* [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding
@ 2015-11-22 8:40 John Crispin
2015-11-22 8:40 ` [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached John Crispin
` (6 more replies)
0 siblings, 7 replies; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
Add three files. ralink,rt2880-net.txt descibes the actual frame engine
and the other two describe the switch forntend bindings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
Cc: devicetree@vger.kernel.org
---
.../bindings/net/mediatek,mt7620-gsw.txt | 26 +++++++++
.../devicetree/bindings/net/ralink,rt2880-net.txt | 61 ++++++++++++++++++++
.../devicetree/bindings/net/ralink,rt3050-esw.txt | 32 ++++++++++
3 files changed, 119 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt
create mode 100644 Documentation/devicetree/bindings/net/ralink,rt2880-net.txt
create mode 100644 Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt
diff --git a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt
new file mode 100644
index 0000000..fb47d8e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt
@@ -0,0 +1,26 @@
+Mediatek Gigabit Switch
+=======================
+
+The mediatek gigabit switch can be found on Mediatek SoCs (mt7620, mt7621).
+
+Required properties:
+- compatible: Should be "mediatek,mt7620-gsw"
+- reg: Address and length of the register set for the device
+- interrupt-parent: Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- interrupts: Should contain the gigabit switches interrupt
+- resets: Should contain the gigabit switches resets
+- reset-names: Should contain the reset names "gsw"
+
+Example:
+
+gsw@10110000 {
+ compatible = "ralink,mt7620-gsw";
+ reg = <0x10110000 8000>;
+
+ resets = <&rstctrl 23>;
+ reset-names = "gsw";
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+};
diff --git a/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt
new file mode 100644
index 0000000..88b095d
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt
@@ -0,0 +1,61 @@
+Ralink Frame Engine Ethernet controller
+=======================================
+
+The Ralink frame engine ethernet controller can be found on Ralink and
+Mediatek SoCs (RT288x, RT3x5x, RT366x, RT388x, rt5350, mt7620, mt7621, mt76x8).
+
+Depending on the SoC, there is a number of ports connected to the CPU port
+directly and/or via a (gigabit-)switch.
+
+* Ethernet controller node
+
+Required properties:
+- compatible: Should be one of "ralink,rt2880-eth", "ralink,rt3050-eth",
+ "ralink,rt3050-eth", "ralink,rt3883-eth", "ralink,rt5350-eth",
+ "mediatek,mt7620-eth", "mediatek,mt7621-eth"
+- reg: Address and length of the register set for the device
+- interrupt-parent: Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- interrupts: Should contain the frame engines interrupt
+- resets: Should contain the frame engines resets
+- reset-names: Should contain the reset names "fe". If a switch is present
+ "esw" is also required.
+
+
+* Ethernet port node
+
+Required properties:
+- compatible: Should be "ralink,eth-port"
+- reg: The number of the physical port
+- phy-handle: reference to the node describing the phy
+
+Example:
+
+mdio-bus {
+ ...
+ phy0: ethernet-phy@0 {
+ phy-mode = "mii";
+ reg = <0>;
+ };
+};
+
+ethernet@400000 {
+ compatible = "ralink,rt2880-eth";
+ reg = <0x00400000 10000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ resets = <&rstctrl 18>;
+ reset-names = "fe";
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <5>;
+
+ port@0 {
+ compatible = "ralink,eth-port";
+ reg = <0>;
+ phy-handle = <&phy0>;
+ };
+
+};
diff --git a/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt
new file mode 100644
index 0000000..ed32e21
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt
@@ -0,0 +1,32 @@
+Ralink Fast Ethernet Embedded Switch
+====================================
+
+The ralink fast ethernet embedded switch can be found on Ralink and Mediatek
+SoCs (RT3x5x, rt5350, mt76x8).
+
+Required properties:
+- compatible: Should be "ralink,rt3050-esw"
+- reg: Address and length of the register set for the device
+- interrupt-parent: Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- interrupts: Should contain the embedded switches interrupt
+- resets: Should contain the embedded switches resets
+- reset-names: Should contain the reset names "esw"
+
+Optional properties:
+- ralink,portmap: can be used to choose if the default switch setup is
+ llllw or wllll
+- ralink,led_polarity: override the active high/low settings of the leds
+
+Example:
+
+esw@10110000 {
+ compatible = "ralink,rt3050-esw";
+ reg = <0x10110000 8000>;
+
+ resets = <&rstctrl 23>;
+ reset-names = "esw";
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
@ 2015-11-22 8:40 ` John Crispin
2015-11-24 18:42 ` Florian Fainelli
2015-11-22 8:40 ` [RFC 3/8] net-next: ralink: add the drivers core files John Crispin
` (5 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
A network core might have more than one phy attached to its cpu port via a
switch. The current code will set the carrier state to on/off when ever a
cable is plugged into any of these ports.
The patch adds a new bool that allows the driver to tell the phy_device to not
set the carrier state. Instead the driver can manually handle the carrier
state.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/phy.c | 9 ++++++---
include/linux/phy.h | 1 +
2 files changed, 7 insertions(+), 3 deletions(-)
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 48ce6ef..bd2df40 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -843,7 +843,8 @@ void phy_state_machine(struct work_struct *work)
/* If the link is down, give up on negotiation for now */
if (!phydev->link) {
phydev->state = PHY_NOLINK;
- netif_carrier_off(phydev->attached_dev);
+ if (!phydev->no_auto_carrier_off)
+ netif_carrier_off(phydev->attached_dev);
phydev->adjust_link(phydev->attached_dev);
break;
}
@@ -926,7 +927,8 @@ void phy_state_machine(struct work_struct *work)
netif_carrier_on(phydev->attached_dev);
} else {
phydev->state = PHY_NOLINK;
- netif_carrier_off(phydev->attached_dev);
+ if (!phydev->no_auto_carrier_off)
+ netif_carrier_off(phydev->attached_dev);
}
phydev->adjust_link(phydev->attached_dev);
@@ -938,7 +940,8 @@ void phy_state_machine(struct work_struct *work)
case PHY_HALTED:
if (phydev->link) {
phydev->link = 0;
- netif_carrier_off(phydev->attached_dev);
+ if (!phydev->no_auto_carrier_off)
+ netif_carrier_off(phydev->attached_dev);
phydev->adjust_link(phydev->attached_dev);
do_suspend = true;
}
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 05fde31..276ab8a 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -377,6 +377,7 @@ struct phy_device {
bool is_pseudo_fixed_link;
bool has_fixups;
bool suspended;
+ bool no_auto_carrier_off;
enum phy_state state;
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 3/8] net-next: ralink: add the drivers core files
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
2015-11-22 8:40 ` [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached John Crispin
@ 2015-11-22 8:40 ` John Crispin
2015-11-22 8:40 ` [RFC 4/8] net-next: ralink: add support for rt2880 John Crispin
` (4 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
This patch adds the main chunk of the driver. The ethernet core is used in all
of the Mediatek/Ralink Wireless SoCs. Over the years we have seen verious
changes to
* the register layout
* the type of ports (single/dual gbit, internal FE/Gbit switch)
* dma engine
and new offloading features were added, such as
* checksum
* vlan tx/rx
* gso
* lro
However the core functionality has remained the sama allowing us to use the
same core for all SoCs.
The abstraction for the various SoCs uses the typical ops struct pattern which
allows us to extend or override the cores functionality depending on which SoC
we are on. The code to bring up the switches and external ports has also been
split into separate files.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
---
drivers/net/ethernet/ralink/mdio.c | 268 +++++
drivers/net/ethernet/ralink/mdio.h | 27 +
drivers/net/ethernet/ralink/ralink_ethtool.c | 235 ++++
drivers/net/ethernet/ralink/ralink_ethtool.h | 22 +
drivers/net/ethernet/ralink/ralink_soc_eth.c | 1622 ++++++++++++++++++++++++++
drivers/net/ethernet/ralink/ralink_soc_eth.h | 519 ++++++++
6 files changed, 2693 insertions(+)
create mode 100644 drivers/net/ethernet/ralink/mdio.c
create mode 100644 drivers/net/ethernet/ralink/mdio.h
create mode 100644 drivers/net/ethernet/ralink/ralink_ethtool.c
create mode 100644 drivers/net/ethernet/ralink/ralink_ethtool.h
create mode 100644 drivers/net/ethernet/ralink/ralink_soc_eth.c
create mode 100644 drivers/net/ethernet/ralink/ralink_soc_eth.h
diff --git a/drivers/net/ethernet/ralink/mdio.c b/drivers/net/ethernet/ralink/mdio.c
new file mode 100644
index 0000000..de95ddb
--- /dev/null
+++ b/drivers/net/ethernet/ralink/mdio.c
@@ -0,0 +1,268 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/skbuff.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+
+#include "ralink_soc_eth.h"
+#include "mdio.h"
+
+static int fe_mdio_reset(struct mii_bus *bus)
+{
+ /* TODO */
+ return 0;
+}
+
+static void fe_phy_link_adjust(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ unsigned long flags;
+ int i;
+
+ spin_lock_irqsave(&priv->phy->lock, flags);
+ for (i = 0; i < 8; i++) {
+ if (priv->phy->phy_node[i]) {
+ struct phy_device *phydev = priv->phy->phy[i];
+ int status_change = 0;
+
+ if (phydev->link)
+ if (priv->phy->duplex[i] != phydev->duplex ||
+ priv->phy->speed[i] != phydev->speed)
+ status_change = 1;
+
+ if (phydev->link != priv->link[i])
+ status_change = 1;
+
+ switch (phydev->speed) {
+ case SPEED_1000:
+ case SPEED_100:
+ case SPEED_10:
+ priv->link[i] = phydev->link;
+ priv->phy->duplex[i] = phydev->duplex;
+ priv->phy->speed[i] = phydev->speed;
+
+ if (status_change &&
+ priv->soc->mdio_adjust_link)
+ priv->soc->mdio_adjust_link(priv, i);
+ break;
+ }
+ }
+ }
+}
+
+int fe_connect_phy_node(struct fe_priv *priv, struct device_node *phy_node)
+{
+ const __be32 *_port = NULL;
+ struct phy_device *phydev;
+ int phy_mode, port;
+
+ _port = of_get_property(phy_node, "reg", NULL);
+
+ if (!_port || (be32_to_cpu(*_port) >= 0x20)) {
+ pr_err("%s: invalid port id\n", phy_node->name);
+ return -EINVAL;
+ }
+ port = be32_to_cpu(*_port);
+ phy_mode = of_get_phy_mode(phy_node);
+ if (phy_mode < 0) {
+ dev_err(priv->device, "incorrect phy-mode %d\n", phy_mode);
+ priv->phy->phy_node[port] = NULL;
+ return -EINVAL;
+ }
+
+ phydev = of_phy_connect(priv->netdev, phy_node, fe_phy_link_adjust,
+ 0, phy_mode);
+ if (IS_ERR(phydev)) {
+ dev_err(priv->device, "could not connect to PHY\n");
+ priv->phy->phy_node[port] = NULL;
+ return PTR_ERR(phydev);
+ }
+
+ phydev->supported &= PHY_GBIT_FEATURES;
+ phydev->advertising = phydev->supported;
+ phydev->no_auto_carrier_off = 1;
+
+ dev_info(priv->device,
+ "connected port %d to PHY at %s [uid=%08x, driver=%s]\n",
+ port, dev_name(&phydev->dev), phydev->phy_id,
+ phydev->drv->name);
+
+ priv->phy->phy[port] = phydev;
+ priv->link[port] = 0;
+
+ return 0;
+}
+
+static void phy_init(struct fe_priv *priv, struct phy_device *phy)
+{
+ phy_attach(priv->netdev, dev_name(&phy->dev), PHY_INTERFACE_MODE_MII);
+
+ phy->autoneg = AUTONEG_ENABLE;
+ phy->speed = 0;
+ phy->duplex = 0;
+ phy->supported &= PHY_BASIC_FEATURES;
+ phy->advertising = phy->supported | ADVERTISED_Autoneg;
+
+ phy_start_aneg(phy);
+}
+
+static int fe_phy_connect(struct fe_priv *priv)
+{
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ if (priv->phy->phy_node[i]) {
+ if (!priv->phy_dev) {
+ priv->phy_dev = priv->phy->phy[i];
+ priv->phy_flags = FE_PHY_FLAG_PORT;
+ }
+ } else if (priv->mii_bus && priv->mii_bus->phy_map[i]) {
+ phy_init(priv, priv->mii_bus->phy_map[i]);
+ if (!priv->phy_dev) {
+ priv->phy_dev = priv->mii_bus->phy_map[i];
+ priv->phy_flags = FE_PHY_FLAG_ATTACH;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static void fe_phy_disconnect(struct fe_priv *priv)
+{
+ unsigned long flags;
+ int i;
+
+ for (i = 0; i < 8; i++)
+ if (priv->phy->phy_fixed[i]) {
+ spin_lock_irqsave(&priv->phy->lock, flags);
+ priv->link[i] = 0;
+ if (priv->soc->mdio_adjust_link)
+ priv->soc->mdio_adjust_link(priv, i);
+ spin_unlock_irqrestore(&priv->phy->lock, flags);
+ } else if (priv->phy->phy[i]) {
+ phy_disconnect(priv->phy->phy[i]);
+ } else if (priv->mii_bus && priv->mii_bus->phy_map[i]) {
+ phy_detach(priv->mii_bus->phy_map[i]);
+ }
+}
+
+static void fe_phy_start(struct fe_priv *priv)
+{
+ unsigned long flags;
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ if (priv->phy->phy_fixed[i]) {
+ spin_lock_irqsave(&priv->phy->lock, flags);
+ priv->link[i] = 1;
+ if (priv->soc->mdio_adjust_link)
+ priv->soc->mdio_adjust_link(priv, i);
+ spin_unlock_irqrestore(&priv->phy->lock, flags);
+ } else if (priv->phy->phy[i]) {
+ phy_start(priv->phy->phy[i]);
+ }
+ }
+}
+
+static void fe_phy_stop(struct fe_priv *priv)
+{
+ unsigned long flags;
+ int i;
+
+ for (i = 0; i < 8; i++)
+ if (priv->phy->phy_fixed[i]) {
+ spin_lock_irqsave(&priv->phy->lock, flags);
+ priv->link[i] = 0;
+ if (priv->soc->mdio_adjust_link)
+ priv->soc->mdio_adjust_link(priv, i);
+ spin_unlock_irqrestore(&priv->phy->lock, flags);
+ } else if (priv->phy->phy[i]) {
+ phy_stop(priv->phy->phy[i]);
+ }
+}
+
+static struct fe_phy phy_ralink = {
+ .connect = fe_phy_connect,
+ .disconnect = fe_phy_disconnect,
+ .start = fe_phy_start,
+ .stop = fe_phy_stop,
+};
+
+int fe_mdio_init(struct fe_priv *priv)
+{
+ struct device_node *mii_np;
+ int err;
+
+ if (!priv->soc->mdio_read || !priv->soc->mdio_write)
+ return 0;
+
+ spin_lock_init(&phy_ralink.lock);
+ priv->phy = &phy_ralink;
+
+ mii_np = of_get_child_by_name(priv->device->of_node, "mdio-bus");
+ if (!mii_np) {
+ dev_err(priv->device, "no %s child node found", "mdio-bus");
+ return -ENODEV;
+ }
+
+ if (!of_device_is_available(mii_np)) {
+ err = 0;
+ goto err_put_node;
+ }
+
+ priv->mii_bus = mdiobus_alloc();
+ if (!priv->mii_bus) {
+ err = -ENOMEM;
+ goto err_put_node;
+ }
+
+ priv->mii_bus->name = "mdio";
+ priv->mii_bus->read = priv->soc->mdio_read;
+ priv->mii_bus->write = priv->soc->mdio_write;
+ priv->mii_bus->reset = fe_mdio_reset;
+ priv->mii_bus->priv = priv;
+ priv->mii_bus->parent = priv->device;
+
+ snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s", mii_np->name);
+ err = of_mdiobus_register(priv->mii_bus, mii_np);
+ if (err)
+ goto err_free_bus;
+
+ return 0;
+
+err_free_bus:
+ kfree(priv->mii_bus);
+err_put_node:
+ of_node_put(mii_np);
+ priv->mii_bus = NULL;
+ return err;
+}
+
+void fe_mdio_cleanup(struct fe_priv *priv)
+{
+ if (!priv->mii_bus)
+ return;
+
+ mdiobus_unregister(priv->mii_bus);
+ of_node_put(priv->mii_bus->dev.of_node);
+ kfree(priv->mii_bus);
+}
diff --git a/drivers/net/ethernet/ralink/mdio.h b/drivers/net/ethernet/ralink/mdio.h
new file mode 100644
index 0000000..b1bb8ec
--- /dev/null
+++ b/drivers/net/ethernet/ralink/mdio.h
@@ -0,0 +1,27 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#ifndef _RALINK_MDIO_H__
+#define _RALINK_MDIO_H__
+
+#ifdef CONFIG_NET_RALINK_MDIO
+int fe_mdio_init(struct fe_priv *priv);
+void fe_mdio_cleanup(struct fe_priv *priv);
+int fe_connect_phy_node(struct fe_priv *priv,
+ struct device_node *phy_node);
+#else
+static inline int fe_mdio_init(struct fe_priv *priv) { return 0; }
+static inline void fe_mdio_cleanup(struct fe_priv *priv) {}
+#endif
+#endif
diff --git a/drivers/net/ethernet/ralink/ralink_ethtool.c b/drivers/net/ethernet/ralink/ralink_ethtool.c
new file mode 100644
index 0000000..2a2c431
--- /dev/null
+++ b/drivers/net/ethernet/ralink/ralink_ethtool.c
@@ -0,0 +1,235 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include "ralink_soc_eth.h"
+
+static const char fe_gdma_str[][ETH_GSTRING_LEN] = {
+#define _FE(x...) # x,
+FE_STAT_REG_DECLARE
+#undef _FE
+};
+
+static int fe_get_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ int err;
+
+ if (!priv->phy_dev)
+ goto out_gset;
+
+ if (priv->phy_flags == FE_PHY_FLAG_ATTACH) {
+ err = phy_read_status(priv->phy_dev);
+ if (err)
+ goto out_gset;
+ }
+
+ return phy_ethtool_gset(priv->phy_dev, cmd);
+
+out_gset:
+ return -ENODEV;
+}
+
+static int fe_set_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ if (!priv->phy_dev)
+ goto out_sset;
+
+ if (cmd->phy_address != priv->phy_dev->addr) {
+ if (priv->phy->phy_node[cmd->phy_address]) {
+ priv->phy_dev = priv->phy->phy[cmd->phy_address];
+ priv->phy_flags = FE_PHY_FLAG_PORT;
+ } else if (priv->mii_bus &&
+ priv->mii_bus->phy_map[cmd->phy_address]) {
+ priv->phy_dev =
+ priv->mii_bus->phy_map[cmd->phy_address];
+ priv->phy_flags = FE_PHY_FLAG_ATTACH;
+ } else {
+ goto out_sset;
+ }
+ }
+
+ return phy_ethtool_sset(priv->phy_dev, cmd);
+
+out_sset:
+ return -ENODEV;
+}
+
+static void fe_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct fe_soc_data *soc = priv->soc;
+
+ strlcpy(info->driver, priv->device->driver->name, sizeof(info->driver));
+ strlcpy(info->version, FE_DRV_VERSION, sizeof(info->version));
+ strlcpy(info->bus_info, dev_name(priv->device), sizeof(info->bus_info));
+
+ if (soc->reg_table[FE_REG_FE_COUNTER_BASE])
+ info->n_stats = ARRAY_SIZE(fe_gdma_str);
+}
+
+static u32 fe_get_msglevel(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ return priv->msg_enable;
+}
+
+static void fe_set_msglevel(struct net_device *dev, u32 value)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ priv->msg_enable = value;
+}
+
+static int fe_nway_reset(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ if (!priv->phy_dev)
+ goto out_nway_reset;
+
+ return genphy_restart_aneg(priv->phy_dev);
+
+out_nway_reset:
+ return -EOPNOTSUPP;
+}
+
+static u32 fe_get_link(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ int err;
+
+ if (!priv->phy_dev)
+ goto out_get_link;
+
+ if (priv->phy_flags == FE_PHY_FLAG_ATTACH) {
+ err = genphy_update_link(priv->phy_dev);
+ if (err)
+ goto out_get_link;
+ }
+
+ return priv->phy_dev->link;
+
+out_get_link:
+ return ethtool_op_get_link(dev);
+}
+
+static int fe_set_ringparam(struct net_device *dev,
+ struct ethtool_ringparam *ring)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ if ((ring->tx_pending < 2) ||
+ (ring->rx_pending < 2) ||
+ (ring->rx_pending > MAX_DMA_DESC) ||
+ (ring->tx_pending > MAX_DMA_DESC))
+ return -EINVAL;
+
+ dev->netdev_ops->ndo_stop(dev);
+
+ priv->tx_ring.tx_ring_size = BIT(fls(ring->tx_pending) - 1);
+ priv->rx_ring.rx_ring_size = BIT(fls(ring->rx_pending) - 1);
+
+ dev->netdev_ops->ndo_open(dev);
+
+ return 0;
+}
+
+static void fe_get_ringparam(struct net_device *dev,
+ struct ethtool_ringparam *ring)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ ring->rx_max_pending = MAX_DMA_DESC;
+ ring->tx_max_pending = MAX_DMA_DESC;
+ ring->rx_pending = priv->rx_ring.rx_ring_size;
+ ring->tx_pending = priv->tx_ring.tx_ring_size;
+}
+
+static void fe_get_strings(struct net_device *dev, u32 stringset, u8 *data)
+{
+ switch (stringset) {
+ case ETH_SS_STATS:
+ memcpy(data, *fe_gdma_str, sizeof(fe_gdma_str));
+ break;
+ }
+}
+
+static int fe_get_sset_count(struct net_device *dev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_STATS:
+ return ARRAY_SIZE(fe_gdma_str);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void fe_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct fe_hw_stats *hwstats = priv->hw_stats;
+ u64 *data_src, *data_dst;
+ unsigned int start;
+ int i;
+
+ if (netif_running(dev) && netif_device_present(dev)) {
+ if (spin_trylock(&hwstats->stats_lock)) {
+ fe_stats_update(priv);
+ spin_unlock(&hwstats->stats_lock);
+ }
+ }
+
+ do {
+ data_src = &hwstats->tx_bytes;
+ data_dst = data;
+ start = u64_stats_fetch_begin_irq(&hwstats->syncp);
+
+ for (i = 0; i < ARRAY_SIZE(fe_gdma_str); i++)
+ *data_dst++ = *data_src++;
+
+ } while (u64_stats_fetch_retry_irq(&hwstats->syncp, start));
+}
+
+static struct ethtool_ops fe_ethtool_ops = {
+ .get_settings = fe_get_settings,
+ .set_settings = fe_set_settings,
+ .get_drvinfo = fe_get_drvinfo,
+ .get_msglevel = fe_get_msglevel,
+ .set_msglevel = fe_set_msglevel,
+ .nway_reset = fe_nway_reset,
+ .get_link = fe_get_link,
+ .set_ringparam = fe_set_ringparam,
+ .get_ringparam = fe_get_ringparam,
+};
+
+void fe_set_ethtool_ops(struct net_device *netdev)
+{
+ struct fe_priv *priv = netdev_priv(netdev);
+ struct fe_soc_data *soc = priv->soc;
+
+ if (soc->reg_table[FE_REG_FE_COUNTER_BASE]) {
+ fe_ethtool_ops.get_strings = fe_get_strings;
+ fe_ethtool_ops.get_sset_count = fe_get_sset_count;
+ fe_ethtool_ops.get_ethtool_stats = fe_get_ethtool_stats;
+ }
+
+ netdev->ethtool_ops = &fe_ethtool_ops;
+}
diff --git a/drivers/net/ethernet/ralink/ralink_ethtool.h b/drivers/net/ethernet/ralink/ralink_ethtool.h
new file mode 100644
index 0000000..955b84f
--- /dev/null
+++ b/drivers/net/ethernet/ralink/ralink_ethtool.h
@@ -0,0 +1,22 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#ifndef FE_ETHTOOL_H
+#define FE_ETHTOOL_H
+
+#include <linux/ethtool.h>
+
+void fe_set_ethtool_ops(struct net_device *netdev);
+
+#endif /* FE_ETHTOOL_H */
diff --git a/drivers/net/ethernet/ralink/ralink_soc_eth.c b/drivers/net/ethernet/ralink/ralink_soc_eth.c
new file mode 100644
index 0000000..41b245f
--- /dev/null
+++ b/drivers/net/ethernet/ralink/ralink_soc_eth.c
@@ -0,0 +1,1622 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/skbuff.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/if_vlan.h>
+#include <linux/reset.h>
+#include <linux/tcp.h>
+#include <linux/io.h>
+#include <linux/bug.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "ralink_soc_eth.h"
+#include "esw_rt3050.h"
+#include "mdio.h"
+#include "ralink_ethtool.h"
+
+#define MAX_RX_LENGTH 1536
+#define FE_RX_ETH_HLEN (VLAN_ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN)
+#define FE_RX_HLEN (NET_SKB_PAD + FE_RX_ETH_HLEN + NET_IP_ALIGN)
+#define DMA_DUMMY_DESC 0xffffffff
+#define FE_DEFAULT_MSG_ENABLE \
+ (NETIF_MSG_DRV | \
+ NETIF_MSG_PROBE | \
+ NETIF_MSG_LINK | \
+ NETIF_MSG_TIMER | \
+ NETIF_MSG_IFDOWN | \
+ NETIF_MSG_IFUP | \
+ NETIF_MSG_RX_ERR | \
+ NETIF_MSG_TX_ERR)
+
+#define TX_DMA_DESP2_DEF (TX_DMA_LS0 | TX_DMA_DONE)
+#define TX_DMA_DESP4_DEF (TX_DMA_QN(3) | TX_DMA_PN(1))
+#define NEXT_TX_DESP_IDX(X) (((X) + 1) & (ring->tx_ring_size - 1))
+#define NEXT_RX_DESP_IDX(X) (((X) + 1) & (ring->rx_ring_size - 1))
+
+#define SYSC_REG_RSTCTRL 0x34
+
+static int fe_msg_level = -1;
+module_param_named(msg_level, fe_msg_level, int, 0);
+MODULE_PARM_DESC(msg_level, "Message level (-1=defaults,0=none,...,16=all)");
+
+static const u16 fe_reg_table_default[FE_REG_COUNT] = {
+ [FE_REG_PDMA_GLO_CFG] = FE_PDMA_GLO_CFG,
+ [FE_REG_PDMA_RST_CFG] = FE_PDMA_RST_CFG,
+ [FE_REG_DLY_INT_CFG] = FE_DLY_INT_CFG,
+ [FE_REG_TX_BASE_PTR0] = FE_TX_BASE_PTR0,
+ [FE_REG_TX_MAX_CNT0] = FE_TX_MAX_CNT0,
+ [FE_REG_TX_CTX_IDX0] = FE_TX_CTX_IDX0,
+ [FE_REG_TX_DTX_IDX0] = FE_TX_DTX_IDX0,
+ [FE_REG_RX_BASE_PTR0] = FE_RX_BASE_PTR0,
+ [FE_REG_RX_MAX_CNT0] = FE_RX_MAX_CNT0,
+ [FE_REG_RX_CALC_IDX0] = FE_RX_CALC_IDX0,
+ [FE_REG_RX_DRX_IDX0] = FE_RX_DRX_IDX0,
+ [FE_REG_FE_INT_ENABLE] = FE_FE_INT_ENABLE,
+ [FE_REG_FE_INT_STATUS] = FE_FE_INT_STATUS,
+ [FE_REG_FE_DMA_VID_BASE] = FE_DMA_VID0,
+ [FE_REG_FE_COUNTER_BASE] = FE_GDMA1_TX_GBCNT,
+ [FE_REG_FE_RST_GL] = FE_FE_RST_GL,
+};
+
+static const u16 *fe_reg_table = fe_reg_table_default;
+
+struct fe_work_t {
+ int bitnr;
+ void (*action)(struct fe_priv *);
+};
+
+static void __iomem *fe_base;
+
+void fe_w32(u32 val, unsigned reg)
+{
+ __raw_writel(val, fe_base + reg);
+}
+
+u32 fe_r32(unsigned reg)
+{
+ return __raw_readl(fe_base + reg);
+}
+
+void fe_reg_w32(u32 val, enum fe_reg reg)
+{
+ fe_w32(val, fe_reg_table[reg]);
+}
+
+u32 fe_reg_r32(enum fe_reg reg)
+{
+ return fe_r32(fe_reg_table[reg]);
+}
+
+void fe_reset(u32 reset_bits)
+{
+ u32 t;
+
+ t = rt_sysc_r32(SYSC_REG_RSTCTRL);
+ t |= reset_bits;
+ rt_sysc_w32(t, SYSC_REG_RSTCTRL);
+ usleep_range(10, 20);
+
+ t &= ~reset_bits;
+ rt_sysc_w32(t, SYSC_REG_RSTCTRL);
+ usleep_range(10, 20);
+}
+
+static inline void fe_int_disable(u32 mask)
+{
+ fe_reg_w32(fe_reg_r32(FE_REG_FE_INT_ENABLE) & ~mask,
+ FE_REG_FE_INT_ENABLE);
+ /* flush write */
+ fe_reg_r32(FE_REG_FE_INT_ENABLE);
+}
+
+static inline void fe_int_enable(u32 mask)
+{
+ fe_reg_w32(fe_reg_r32(FE_REG_FE_INT_ENABLE) | mask,
+ FE_REG_FE_INT_ENABLE);
+ /* flush write */
+ fe_reg_r32(FE_REG_FE_INT_ENABLE);
+}
+
+static inline void fe_hw_set_macaddr(struct fe_priv *priv, unsigned char *mac)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->page_lock, flags);
+ fe_w32((mac[0] << 8) | mac[1], FE_GDMA1_MAC_ADRH);
+ fe_w32((mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5],
+ FE_GDMA1_MAC_ADRL);
+ spin_unlock_irqrestore(&priv->page_lock, flags);
+}
+
+static int fe_set_mac_address(struct net_device *dev, void *p)
+{
+ int ret = eth_mac_addr(dev, p);
+
+ if (!ret) {
+ struct fe_priv *priv = netdev_priv(dev);
+
+ if (priv->soc->set_mac)
+ priv->soc->set_mac(priv, dev->dev_addr);
+ else
+ fe_hw_set_macaddr(priv, p);
+ }
+
+ return ret;
+}
+
+static inline int fe_max_frag_size(int mtu)
+{
+ /* make sure buf_size will be at least MAX_RX_LENGTH */
+ if (mtu + FE_RX_ETH_HLEN < MAX_RX_LENGTH)
+ mtu = MAX_RX_LENGTH - FE_RX_ETH_HLEN;
+
+ return SKB_DATA_ALIGN(FE_RX_HLEN + mtu) +
+ SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+}
+
+static inline int fe_max_buf_size(int frag_size)
+{
+ int buf_size = frag_size - NET_SKB_PAD - NET_IP_ALIGN -
+ SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
+
+ BUG_ON(buf_size < MAX_RX_LENGTH);
+ return buf_size;
+}
+
+static inline void fe_get_rxd(struct fe_rx_dma *rxd, struct fe_rx_dma *dma_rxd)
+{
+ rxd->rxd1 = dma_rxd->rxd1;
+ rxd->rxd2 = dma_rxd->rxd2;
+ rxd->rxd3 = dma_rxd->rxd3;
+ rxd->rxd4 = dma_rxd->rxd4;
+}
+
+static inline void fe_set_txd(struct fe_tx_dma *txd, struct fe_tx_dma *dma_txd)
+{
+ dma_txd->txd1 = txd->txd1;
+ dma_txd->txd3 = txd->txd3;
+ dma_txd->txd4 = txd->txd4;
+ /* clean dma done flag last */
+ dma_txd->txd2 = txd->txd2;
+}
+
+static void fe_clean_rx(struct fe_priv *priv)
+{
+ int i;
+ struct fe_rx_ring *ring = &priv->rx_ring;
+
+ if (ring->rx_data) {
+ for (i = 0; i < ring->rx_ring_size; i++)
+ if (ring->rx_data[i]) {
+ if (ring->rx_dma && ring->rx_dma[i].rxd1)
+ dma_unmap_single(&priv->netdev->dev,
+ ring->rx_dma[i].rxd1,
+ ring->rx_buf_size,
+ DMA_FROM_DEVICE);
+ put_page(virt_to_head_page(ring->rx_data[i]));
+ }
+
+ kfree(ring->rx_data);
+ ring->rx_data = NULL;
+ }
+
+ if (ring->rx_dma) {
+ dma_free_coherent(&priv->netdev->dev,
+ ring->rx_ring_size * sizeof(*ring->rx_dma),
+ ring->rx_dma,
+ ring->rx_phys);
+ ring->rx_dma = NULL;
+ }
+}
+
+static int fe_alloc_rx(struct fe_priv *priv)
+{
+ struct net_device *netdev = priv->netdev;
+ struct fe_rx_ring *ring = &priv->rx_ring;
+ int i, pad;
+
+ ring->rx_data = kcalloc(ring->rx_ring_size, sizeof(*ring->rx_data),
+ GFP_KERNEL);
+ if (!ring->rx_data)
+ goto no_rx_mem;
+
+ for (i = 0; i < ring->rx_ring_size; i++) {
+ ring->rx_data[i] = netdev_alloc_frag(ring->frag_size);
+ if (!ring->rx_data[i])
+ goto no_rx_mem;
+ }
+
+ ring->rx_dma = dma_alloc_coherent(&netdev->dev,
+ ring->rx_ring_size * sizeof(*ring->rx_dma),
+ &ring->rx_phys,
+ GFP_ATOMIC | __GFP_ZERO);
+ if (!ring->rx_dma)
+ goto no_rx_mem;
+
+ if (priv->flags & FE_FLAG_RX_2B_OFFSET)
+ pad = 0;
+ else
+ pad = NET_IP_ALIGN;
+ for (i = 0; i < ring->rx_ring_size; i++) {
+ dma_addr_t dma_addr = dma_map_single(&netdev->dev,
+ ring->rx_data[i] + NET_SKB_PAD + pad,
+ ring->rx_buf_size,
+ DMA_FROM_DEVICE);
+ if (unlikely(dma_mapping_error(&netdev->dev, dma_addr)))
+ goto no_rx_mem;
+ ring->rx_dma[i].rxd1 = (unsigned int)dma_addr;
+
+ if (priv->flags & FE_FLAG_RX_SG_DMA)
+ ring->rx_dma[i].rxd2 = RX_DMA_PLEN0(ring->rx_buf_size);
+ else
+ ring->rx_dma[i].rxd2 = RX_DMA_LSO;
+ }
+ ring->rx_calc_idx = ring->rx_ring_size - 1;
+ /* make sure that all changes to the dma ring are flushed before we
+ * continue
+ */
+ wmb();
+
+ fe_reg_w32(ring->rx_phys, FE_REG_RX_BASE_PTR0);
+ fe_reg_w32(ring->rx_ring_size, FE_REG_RX_MAX_CNT0);
+ fe_reg_w32(ring->rx_calc_idx, FE_REG_RX_CALC_IDX0);
+ fe_reg_w32(FE_PST_DRX_IDX0, FE_REG_PDMA_RST_CFG);
+
+ return 0;
+
+no_rx_mem:
+ return -ENOMEM;
+}
+
+static void fe_txd_unmap(struct device *dev, struct fe_tx_buf *tx_buf)
+{
+ if (tx_buf->flags & FE_TX_FLAGS_SINGLE0) {
+ dma_unmap_single(dev,
+ dma_unmap_addr(tx_buf, dma_addr0),
+ dma_unmap_len(tx_buf, dma_len0),
+ DMA_TO_DEVICE);
+ } else if (tx_buf->flags & FE_TX_FLAGS_PAGE0) {
+ dma_unmap_page(dev,
+ dma_unmap_addr(tx_buf, dma_addr0),
+ dma_unmap_len(tx_buf, dma_len0),
+ DMA_TO_DEVICE);
+ }
+ if (tx_buf->flags & FE_TX_FLAGS_PAGE1)
+ dma_unmap_page(dev,
+ dma_unmap_addr(tx_buf, dma_addr1),
+ dma_unmap_len(tx_buf, dma_len1),
+ DMA_TO_DEVICE);
+
+ tx_buf->flags = 0;
+ if (tx_buf->skb && (tx_buf->skb != (struct sk_buff *)DMA_DUMMY_DESC))
+ dev_kfree_skb_any(tx_buf->skb);
+ tx_buf->skb = NULL;
+}
+
+static void fe_clean_tx(struct fe_priv *priv)
+{
+ int i;
+ struct device *dev = &priv->netdev->dev;
+ struct fe_tx_ring *ring = &priv->tx_ring;
+
+ if (ring->tx_buf) {
+ for (i = 0; i < ring->tx_ring_size; i++)
+ fe_txd_unmap(dev, &ring->tx_buf[i]);
+ kfree(ring->tx_buf);
+ ring->tx_buf = NULL;
+ }
+
+ if (ring->tx_dma) {
+ dma_free_coherent(dev,
+ ring->tx_ring_size * sizeof(*ring->tx_dma),
+ ring->tx_dma,
+ ring->tx_phys);
+ ring->tx_dma = NULL;
+ }
+
+ netdev_reset_queue(priv->netdev);
+}
+
+static int fe_alloc_tx(struct fe_priv *priv)
+{
+ int i;
+ struct fe_tx_ring *ring = &priv->tx_ring;
+
+ ring->tx_free_idx = 0;
+ ring->tx_next_idx = 0;
+ ring->tx_thresh = max((unsigned long)ring->tx_ring_size >> 2,
+ MAX_SKB_FRAGS);
+
+ ring->tx_buf = kcalloc(ring->tx_ring_size, sizeof(*ring->tx_buf),
+ GFP_KERNEL);
+ if (!ring->tx_buf)
+ goto no_tx_mem;
+
+ ring->tx_dma = dma_alloc_coherent(&priv->netdev->dev,
+ ring->tx_ring_size * sizeof(*ring->tx_dma),
+ &ring->tx_phys,
+ GFP_ATOMIC | __GFP_ZERO);
+ if (!ring->tx_dma)
+ goto no_tx_mem;
+
+ for (i = 0; i < ring->tx_ring_size; i++) {
+ if (priv->soc->tx_dma)
+ priv->soc->tx_dma(&ring->tx_dma[i]);
+ ring->tx_dma[i].txd2 = TX_DMA_DESP2_DEF;
+ }
+ /* make sure that all changes to the dma ring are flushed before we
+ * continue
+ */
+ wmb();
+
+ fe_reg_w32(ring->tx_phys, FE_REG_TX_BASE_PTR0);
+ fe_reg_w32(ring->tx_ring_size, FE_REG_TX_MAX_CNT0);
+ fe_reg_w32(0, FE_REG_TX_CTX_IDX0);
+ fe_reg_w32(FE_PST_DTX_IDX0, FE_REG_PDMA_RST_CFG);
+
+ return 0;
+
+no_tx_mem:
+ return -ENOMEM;
+}
+
+static int fe_init_dma(struct fe_priv *priv)
+{
+ int err;
+
+ err = fe_alloc_tx(priv);
+ if (err)
+ return err;
+
+ err = fe_alloc_rx(priv);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+static void fe_free_dma(struct fe_priv *priv)
+{
+ fe_clean_tx(priv);
+ fe_clean_rx(priv);
+}
+
+void fe_stats_update(struct fe_priv *priv)
+{
+ struct fe_hw_stats *hwstats = priv->hw_stats;
+ unsigned int base = fe_reg_table[FE_REG_FE_COUNTER_BASE];
+ u64 stats;
+
+ u64_stats_update_begin(&hwstats->syncp);
+
+ if (IS_ENABLED(CONFIG_SOC_MT7621)) {
+ hwstats->rx_bytes += fe_r32(base);
+ stats = fe_r32(base + 0x04);
+ if (stats)
+ hwstats->rx_bytes += (stats << 32);
+ hwstats->rx_packets += fe_r32(base + 0x08);
+ hwstats->rx_overflow += fe_r32(base + 0x10);
+ hwstats->rx_fcs_errors += fe_r32(base + 0x14);
+ hwstats->rx_short_errors += fe_r32(base + 0x18);
+ hwstats->rx_long_errors += fe_r32(base + 0x1c);
+ hwstats->rx_checksum_errors += fe_r32(base + 0x20);
+ hwstats->rx_flow_control_packets += fe_r32(base + 0x24);
+ hwstats->tx_skip += fe_r32(base + 0x28);
+ hwstats->tx_collisions += fe_r32(base + 0x2c);
+ hwstats->tx_bytes += fe_r32(base + 0x30);
+ stats = fe_r32(base + 0x34);
+ if (stats)
+ hwstats->tx_bytes += (stats << 32);
+ hwstats->tx_packets += fe_r32(base + 0x38);
+ } else {
+ hwstats->tx_bytes += fe_r32(base);
+ hwstats->tx_packets += fe_r32(base + 0x04);
+ hwstats->tx_skip += fe_r32(base + 0x08);
+ hwstats->tx_collisions += fe_r32(base + 0x0c);
+ hwstats->rx_bytes += fe_r32(base + 0x20);
+ hwstats->rx_packets += fe_r32(base + 0x24);
+ hwstats->rx_overflow += fe_r32(base + 0x28);
+ hwstats->rx_fcs_errors += fe_r32(base + 0x2c);
+ hwstats->rx_short_errors += fe_r32(base + 0x30);
+ hwstats->rx_long_errors += fe_r32(base + 0x34);
+ hwstats->rx_checksum_errors += fe_r32(base + 0x38);
+ hwstats->rx_flow_control_packets += fe_r32(base + 0x3c);
+ }
+
+ u64_stats_update_end(&hwstats->syncp);
+}
+
+static struct rtnl_link_stats64 *fe_get_stats64(struct net_device *dev,
+ struct rtnl_link_stats64 *storage)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct fe_hw_stats *hwstats = priv->hw_stats;
+ unsigned int base = fe_reg_table[FE_REG_FE_COUNTER_BASE];
+ unsigned int start;
+
+ if (!base) {
+ netdev_stats_to_stats64(storage, &dev->stats);
+ return storage;
+ }
+
+ if (netif_running(dev) && netif_device_present(dev)) {
+ if (spin_trylock(&hwstats->stats_lock)) {
+ fe_stats_update(priv);
+ spin_unlock(&hwstats->stats_lock);
+ }
+ }
+
+ do {
+ start = u64_stats_fetch_begin_irq(&hwstats->syncp);
+ storage->rx_packets = hwstats->rx_packets;
+ storage->tx_packets = hwstats->tx_packets;
+ storage->rx_bytes = hwstats->rx_bytes;
+ storage->tx_bytes = hwstats->tx_bytes;
+ storage->collisions = hwstats->tx_collisions;
+ storage->rx_length_errors = hwstats->rx_short_errors +
+ hwstats->rx_long_errors;
+ storage->rx_over_errors = hwstats->rx_overflow;
+ storage->rx_crc_errors = hwstats->rx_fcs_errors;
+ storage->rx_errors = hwstats->rx_checksum_errors;
+ storage->tx_aborted_errors = hwstats->tx_skip;
+ } while (u64_stats_fetch_retry_irq(&hwstats->syncp, start));
+
+ storage->tx_errors = priv->netdev->stats.tx_errors;
+ storage->rx_dropped = priv->netdev->stats.rx_dropped;
+ storage->tx_dropped = priv->netdev->stats.tx_dropped;
+
+ return storage;
+}
+
+static int fe_vlan_rx_add_vid(struct net_device *dev,
+ __be16 proto, u16 vid)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ u32 idx = (vid & 0xf);
+ u32 vlan_cfg;
+
+ if (!((fe_reg_table[FE_REG_FE_DMA_VID_BASE]) &&
+ (dev->features & NETIF_F_HW_VLAN_CTAG_TX)))
+ return 0;
+
+ if (test_bit(idx, &priv->vlan_map)) {
+ netdev_warn(dev, "disable tx vlan offload\n");
+ dev->wanted_features &= ~NETIF_F_HW_VLAN_CTAG_TX;
+ netdev_update_features(dev);
+ } else {
+ vlan_cfg = fe_r32(fe_reg_table[FE_REG_FE_DMA_VID_BASE] +
+ ((idx >> 1) << 2));
+ if (idx & 0x1) {
+ vlan_cfg &= 0xffff;
+ vlan_cfg |= (vid << 16);
+ } else {
+ vlan_cfg &= 0xffff0000;
+ vlan_cfg |= vid;
+ }
+ fe_w32(vlan_cfg, fe_reg_table[FE_REG_FE_DMA_VID_BASE] +
+ ((idx >> 1) << 2));
+ set_bit(idx, &priv->vlan_map);
+ }
+
+ return 0;
+}
+
+static int fe_vlan_rx_kill_vid(struct net_device *dev,
+ __be16 proto, u16 vid)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ u32 idx = (vid & 0xf);
+
+ if (!((fe_reg_table[FE_REG_FE_DMA_VID_BASE]) &&
+ (dev->features & NETIF_F_HW_VLAN_CTAG_TX)))
+ return 0;
+
+ clear_bit(idx, &priv->vlan_map);
+
+ return 0;
+}
+
+static inline u32 fe_empty_txd(struct fe_tx_ring *ring)
+{
+ barrier();
+ return (u32)(ring->tx_ring_size -
+ ((ring->tx_next_idx - ring->tx_free_idx) &
+ (ring->tx_ring_size - 1)));
+}
+
+static int fe_tx_map_dma(struct sk_buff *skb, struct net_device *dev,
+ int tx_num, struct fe_tx_ring *ring)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct skb_frag_struct *frag;
+ struct fe_tx_dma txd, *ptxd;
+ struct fe_tx_buf *tx_buf;
+ dma_addr_t mapped_addr;
+ unsigned int nr_frags;
+ u32 def_txd4;
+ int i, j, k, frag_size, frag_map_size, offset;
+
+ tx_buf = &ring->tx_buf[ring->tx_next_idx];
+ memset(tx_buf, 0, sizeof(*tx_buf));
+ memset(&txd, 0, sizeof(txd));
+ nr_frags = skb_shinfo(skb)->nr_frags;
+
+ /* init tx descriptor */
+ if (priv->soc->tx_dma)
+ priv->soc->tx_dma(&txd);
+ else
+ txd.txd4 = TX_DMA_DESP4_DEF;
+ def_txd4 = txd.txd4;
+
+ /* TX Checksum offload */
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
+ txd.txd4 |= TX_DMA_CHKSUM;
+
+ /* VLAN header offload */
+ if (skb_vlan_tag_present(skb)) {
+ u16 tag = skb_vlan_tag_get(skb);
+
+ if (IS_ENABLED(CONFIG_SOC_MT7621))
+ txd.txd4 |= TX_DMA_INS_VLAN_MT7621 | tag;
+ else
+ txd.txd4 |= TX_DMA_INS_VLAN |
+ ((tag >> VLAN_PRIO_SHIFT) << 4) |
+ (tag & 0xF);
+ }
+
+ /* TSO: fill MSS info in tcp checksum field */
+ if (skb_is_gso(skb)) {
+ if (skb_cow_head(skb, 0)) {
+ netif_warn(priv, tx_err, dev,
+ "GSO expand head fail.\n");
+ goto err_out;
+ }
+ if (skb_shinfo(skb)->gso_type &
+ (SKB_GSO_TCPV4 | SKB_GSO_TCPV6)) {
+ txd.txd4 |= TX_DMA_TSO;
+ tcp_hdr(skb)->check = htons(skb_shinfo(skb)->gso_size);
+ }
+ }
+
+ mapped_addr = dma_map_single(&dev->dev, skb->data,
+ skb_headlen(skb), DMA_TO_DEVICE);
+ if (unlikely(dma_mapping_error(&dev->dev, mapped_addr)))
+ goto err_out;
+ txd.txd1 = mapped_addr;
+ txd.txd2 = TX_DMA_PLEN0(skb_headlen(skb));
+
+ tx_buf->flags |= FE_TX_FLAGS_SINGLE0;
+ dma_unmap_addr_set(tx_buf, dma_addr0, mapped_addr);
+ dma_unmap_len_set(tx_buf, dma_len0, skb_headlen(skb));
+
+ /* TX SG offload */
+ j = ring->tx_next_idx;
+ k = 0;
+ for (i = 0; i < nr_frags; i++) {
+ offset = 0;
+ frag = &skb_shinfo(skb)->frags[i];
+ frag_size = skb_frag_size(frag);
+
+ while (frag_size > 0) {
+ frag_map_size = min(frag_size, TX_DMA_BUF_LEN);
+ mapped_addr = skb_frag_dma_map(&dev->dev, frag, offset,
+ frag_map_size,
+ DMA_TO_DEVICE);
+ if (unlikely(dma_mapping_error(&dev->dev, mapped_addr)))
+ goto err_dma;
+
+ if (k & 0x1) {
+ j = NEXT_TX_DESP_IDX(j);
+ txd.txd1 = mapped_addr;
+ txd.txd2 = TX_DMA_PLEN0(frag_map_size);
+ txd.txd4 = def_txd4;
+
+ tx_buf = &ring->tx_buf[j];
+ memset(tx_buf, 0, sizeof(*tx_buf));
+
+ tx_buf->flags |= FE_TX_FLAGS_PAGE0;
+ dma_unmap_addr_set(tx_buf, dma_addr0,
+ mapped_addr);
+ dma_unmap_len_set(tx_buf, dma_len0,
+ frag_map_size);
+ } else {
+ txd.txd3 = mapped_addr;
+ txd.txd2 |= TX_DMA_PLEN1(frag_map_size);
+
+ tx_buf->skb = (struct sk_buff *)DMA_DUMMY_DESC;
+ tx_buf->flags |= FE_TX_FLAGS_PAGE1;
+ dma_unmap_addr_set(tx_buf, dma_addr1,
+ mapped_addr);
+ dma_unmap_len_set(tx_buf, dma_len1,
+ frag_map_size);
+
+ if (!((i == (nr_frags - 1)) &&
+ (frag_map_size == frag_size))) {
+ fe_set_txd(&txd, &ring->tx_dma[j]);
+ memset(&txd, 0, sizeof(txd));
+ }
+ }
+ frag_size -= frag_map_size;
+ offset += frag_map_size;
+ k++;
+ }
+ }
+
+ /* set last segment */
+ if (k & 0x1)
+ txd.txd2 |= TX_DMA_LS1;
+ else
+ txd.txd2 |= TX_DMA_LS0;
+ fe_set_txd(&txd, &ring->tx_dma[j]);
+
+ /* store skb to cleanup */
+ tx_buf->skb = skb;
+
+ netdev_sent_queue(dev, skb->len);
+ skb_tx_timestamp(skb);
+
+ ring->tx_next_idx = NEXT_TX_DESP_IDX(j);
+ /* make sure that all changes to the dma ring are flushed before we
+ * continue
+ */
+ wmb();
+ if (unlikely(fe_empty_txd(ring) <= ring->tx_thresh)) {
+ netif_stop_queue(dev);
+ smp_mb();
+ if (unlikely(fe_empty_txd(ring) > ring->tx_thresh))
+ netif_wake_queue(dev);
+ }
+
+ if (netif_xmit_stopped(netdev_get_tx_queue(dev, 0)) || !skb->xmit_more)
+ fe_reg_w32(ring->tx_next_idx, FE_REG_TX_CTX_IDX0);
+
+ return 0;
+
+err_dma:
+ j = ring->tx_next_idx;
+ for (i = 0; i < tx_num; i++) {
+ ptxd = &ring->tx_dma[j];
+ tx_buf = &ring->tx_buf[j];
+
+ /* unmap dma */
+ fe_txd_unmap(&dev->dev, tx_buf);
+
+ ptxd->txd2 = TX_DMA_DESP2_DEF;
+ j = NEXT_TX_DESP_IDX(j);
+ }
+ /* make sure that all changes to the dma ring are flushed before we
+ * continue
+ */
+ wmb();
+
+err_out:
+ return -1;
+}
+
+static inline int fe_skb_padto(struct sk_buff *skb, struct fe_priv *priv)
+{
+ unsigned int len;
+ int ret;
+
+ ret = 0;
+ if (unlikely(skb->len < VLAN_ETH_ZLEN)) {
+ if ((priv->flags & FE_FLAG_PADDING_64B) &&
+ !(priv->flags & FE_FLAG_PADDING_BUG))
+ return ret;
+
+ if (skb_vlan_tag_present(skb))
+ len = ETH_ZLEN;
+ else if (skb->protocol == cpu_to_be16(ETH_P_8021Q))
+ len = VLAN_ETH_ZLEN;
+ else if (!(priv->flags & FE_FLAG_PADDING_64B))
+ len = ETH_ZLEN;
+ else
+ return ret;
+
+ if (skb->len < len) {
+ ret = skb_pad(skb, len - skb->len);
+ if (ret < 0)
+ return ret;
+ skb->len = len;
+ skb_set_tail_pointer(skb, len);
+ }
+ }
+
+ return ret;
+}
+
+static inline int fe_cal_txd_req(struct sk_buff *skb)
+{
+ int i, nfrags;
+ struct skb_frag_struct *frag;
+
+ nfrags = 1;
+ if (skb_is_gso(skb)) {
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ frag = &skb_shinfo(skb)->frags[i];
+ nfrags += DIV_ROUND_UP(frag->size, TX_DMA_BUF_LEN);
+ }
+ } else {
+ nfrags += skb_shinfo(skb)->nr_frags;
+ }
+
+ return DIV_ROUND_UP(nfrags, 2);
+}
+
+static int fe_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct fe_tx_ring *ring = &priv->tx_ring;
+ struct net_device_stats *stats = &dev->stats;
+ int tx_num;
+ int len = skb->len;
+
+ if (fe_skb_padto(skb, priv)) {
+ netif_warn(priv, tx_err, dev, "tx padding failed!\n");
+ return NETDEV_TX_OK;
+ }
+
+ tx_num = fe_cal_txd_req(skb);
+ if (unlikely(fe_empty_txd(ring) <= tx_num)) {
+ netif_stop_queue(dev);
+ netif_err(priv, tx_queued, dev,
+ "Tx Ring full when queue awake!\n");
+ return NETDEV_TX_BUSY;
+ }
+
+ if (fe_tx_map_dma(skb, dev, tx_num, ring) < 0) {
+ stats->tx_dropped++;
+ } else {
+ stats->tx_packets++;
+ stats->tx_bytes += len;
+ }
+
+ return NETDEV_TX_OK;
+}
+
+static inline void fe_rx_vlan(struct sk_buff *skb)
+{
+ struct ethhdr *ehdr;
+ u16 vlanid;
+
+ if (!__vlan_get_tag(skb, &vlanid)) {
+ /* pop the vlan tag */
+ ehdr = (struct ethhdr *)skb->data;
+ memmove(skb->data + VLAN_HLEN, ehdr, ETH_ALEN * 2);
+ skb_pull(skb, VLAN_HLEN);
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlanid);
+ }
+}
+
+static int fe_poll_rx(struct napi_struct *napi, int budget,
+ struct fe_priv *priv, u32 rx_intr)
+{
+ struct net_device *netdev = priv->netdev;
+ struct net_device_stats *stats = &netdev->stats;
+ struct fe_soc_data *soc = priv->soc;
+ struct fe_rx_ring *ring = &priv->rx_ring;
+ int idx = ring->rx_calc_idx;
+ u32 checksum_bit;
+ struct sk_buff *skb;
+ u8 *data, *new_data;
+ struct fe_rx_dma *rxd, trxd;
+ int done = 0, pad;
+ bool rx_vlan = netdev->features & NETIF_F_HW_VLAN_CTAG_RX;
+
+ if (netdev->features & NETIF_F_RXCSUM)
+ checksum_bit = soc->checksum_bit;
+ else
+ checksum_bit = 0;
+
+ if (priv->flags & FE_FLAG_RX_2B_OFFSET)
+ pad = 0;
+ else
+ pad = NET_IP_ALIGN;
+
+ while (done < budget) {
+ unsigned int pktlen;
+ dma_addr_t dma_addr;
+
+ idx = NEXT_RX_DESP_IDX(idx);
+ rxd = &ring->rx_dma[idx];
+ data = ring->rx_data[idx];
+
+ fe_get_rxd(&trxd, rxd);
+ if (!(trxd.rxd2 & RX_DMA_DONE))
+ break;
+
+ /* alloc new buffer */
+ new_data = netdev_alloc_frag(ring->frag_size);
+ if (unlikely(!new_data)) {
+ stats->rx_dropped++;
+ goto release_desc;
+ }
+ dma_addr = dma_map_single(&netdev->dev,
+ new_data + NET_SKB_PAD + pad,
+ ring->rx_buf_size,
+ DMA_FROM_DEVICE);
+ if (unlikely(dma_mapping_error(&netdev->dev, dma_addr))) {
+ put_page(virt_to_head_page(new_data));
+ goto release_desc;
+ }
+
+ /* receive data */
+ skb = build_skb(data, ring->frag_size);
+ if (unlikely(!skb)) {
+ put_page(virt_to_head_page(new_data));
+ goto release_desc;
+ }
+ skb_reserve(skb, NET_SKB_PAD + NET_IP_ALIGN);
+
+ dma_unmap_single(&netdev->dev, trxd.rxd1,
+ ring->rx_buf_size, DMA_FROM_DEVICE);
+ pktlen = RX_DMA_GET_PLEN0(trxd.rxd2);
+ skb->dev = netdev;
+ skb_put(skb, pktlen);
+ if (trxd.rxd4 & checksum_bit)
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ else
+ skb_checksum_none_assert(skb);
+ if (rx_vlan)
+ fe_rx_vlan(skb);
+ skb->protocol = eth_type_trans(skb, netdev);
+
+ stats->rx_packets++;
+ stats->rx_bytes += pktlen;
+
+ napi_gro_receive(napi, skb);
+
+ ring->rx_data[idx] = new_data;
+ rxd->rxd1 = (unsigned int)dma_addr;
+
+release_desc:
+ if (priv->flags & FE_FLAG_RX_SG_DMA)
+ rxd->rxd2 = RX_DMA_PLEN0(ring->rx_buf_size);
+ else
+ rxd->rxd2 = RX_DMA_LSO;
+
+ ring->rx_calc_idx = idx;
+ /* make sure that all changes to the dma ring are flushed before
+ * we continue
+ */
+ wmb();
+ fe_reg_w32(ring->rx_calc_idx, FE_REG_RX_CALC_IDX0);
+ done++;
+ }
+
+ if (done < budget)
+ fe_reg_w32(rx_intr, FE_REG_FE_INT_STATUS);
+
+ return done;
+}
+
+static int fe_poll_tx(struct fe_priv *priv, int budget, u32 tx_intr,
+ int *tx_again)
+{
+ struct net_device *netdev = priv->netdev;
+ struct device *dev = &netdev->dev;
+ unsigned int bytes_compl = 0;
+ struct sk_buff *skb;
+ struct fe_tx_buf *tx_buf;
+ int done = 0;
+ u32 idx, hwidx;
+ struct fe_tx_ring *ring = &priv->tx_ring;
+
+ idx = ring->tx_free_idx;
+ hwidx = fe_reg_r32(FE_REG_TX_DTX_IDX0);
+
+ while ((idx != hwidx) && budget) {
+ tx_buf = &ring->tx_buf[idx];
+ skb = tx_buf->skb;
+
+ if (!skb)
+ break;
+
+ if (skb != (struct sk_buff *)DMA_DUMMY_DESC) {
+ bytes_compl += skb->len;
+ done++;
+ budget--;
+ }
+ fe_txd_unmap(dev, tx_buf);
+ idx = NEXT_TX_DESP_IDX(idx);
+ }
+ ring->tx_free_idx = idx;
+
+ if (idx == hwidx) {
+ /* read hw index again make sure no new tx packet */
+ hwidx = fe_reg_r32(FE_REG_TX_DTX_IDX0);
+ if (idx == hwidx)
+ fe_reg_w32(tx_intr, FE_REG_FE_INT_STATUS);
+ else
+ *tx_again = 1;
+ } else {
+ *tx_again = 1;
+ }
+
+ if (done) {
+ netdev_completed_queue(netdev, done, bytes_compl);
+ smp_mb();
+ if (unlikely(netif_queue_stopped(netdev) &&
+ (fe_empty_txd(ring) > ring->tx_thresh)))
+ netif_wake_queue(netdev);
+ }
+
+ return done;
+}
+
+static int fe_poll(struct napi_struct *napi, int budget)
+{
+ struct fe_priv *priv = container_of(napi, struct fe_priv, rx_napi);
+ struct fe_hw_stats *hwstat = priv->hw_stats;
+ int tx_done, rx_done, tx_again;
+ u32 status, fe_status, status_reg, mask;
+ u32 tx_intr, rx_intr, status_intr;
+
+ status = fe_reg_r32(FE_REG_FE_INT_STATUS);
+ fe_status = status;
+ tx_intr = priv->soc->tx_int;
+ rx_intr = priv->soc->rx_int;
+ status_intr = priv->soc->status_int;
+ tx_done = 0;
+ rx_done = 0;
+ tx_again = 0;
+
+ if (fe_reg_table[FE_REG_FE_INT_STATUS2]) {
+ fe_status = fe_reg_r32(FE_REG_FE_INT_STATUS2);
+ status_reg = FE_REG_FE_INT_STATUS2;
+ } else {
+ status_reg = FE_REG_FE_INT_STATUS;
+ }
+
+ if (status & tx_intr)
+ tx_done = fe_poll_tx(priv, budget, tx_intr, &tx_again);
+
+ if (status & rx_intr)
+ rx_done = fe_poll_rx(napi, budget, priv, rx_intr);
+
+ if (unlikely(fe_status & status_intr)) {
+ if (hwstat && spin_trylock(&hwstat->stats_lock)) {
+ fe_stats_update(priv);
+ spin_unlock(&hwstat->stats_lock);
+ }
+ fe_reg_w32(status_intr, status_reg);
+ }
+
+ if (unlikely(netif_msg_intr(priv))) {
+ mask = fe_reg_r32(FE_REG_FE_INT_ENABLE);
+ netdev_info(priv->netdev,
+ "done tx %d, rx %d, intr 0x%08x/0x%x\n",
+ tx_done, rx_done, status, mask);
+ }
+
+ if (!tx_again && (rx_done < budget)) {
+ status = fe_reg_r32(FE_REG_FE_INT_STATUS);
+ if (status & (tx_intr | rx_intr)) {
+ /* let napi poll again */
+ rx_done = budget;
+ goto poll_again;
+ }
+
+ napi_complete(napi);
+ fe_int_enable(tx_intr | rx_intr);
+ }
+
+poll_again:
+ return rx_done;
+}
+
+static void fe_tx_timeout(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct fe_tx_ring *ring = &priv->tx_ring;
+
+ priv->netdev->stats.tx_errors++;
+ netif_err(priv, tx_err, dev,
+ "transmit timed out\n");
+ netif_info(priv, drv, dev, "dma_cfg:%08x\n",
+ fe_reg_r32(FE_REG_PDMA_GLO_CFG));
+ netif_info(priv, drv, dev, "tx_ring=%d, "
+ "base=%08x, max=%u, ctx=%u, dtx=%u, fdx=%hu, next=%hu\n",
+ 0, fe_reg_r32(FE_REG_TX_BASE_PTR0),
+ fe_reg_r32(FE_REG_TX_MAX_CNT0),
+ fe_reg_r32(FE_REG_TX_CTX_IDX0),
+ fe_reg_r32(FE_REG_TX_DTX_IDX0),
+ ring->tx_free_idx,
+ ring->tx_next_idx);
+ netif_info(priv, drv, dev,
+ "rx_ring=%d, base=%08x, max=%u, calc=%u, drx=%u\n",
+ 0, fe_reg_r32(FE_REG_RX_BASE_PTR0),
+ fe_reg_r32(FE_REG_RX_MAX_CNT0),
+ fe_reg_r32(FE_REG_RX_CALC_IDX0),
+ fe_reg_r32(FE_REG_RX_DRX_IDX0));
+
+ if (!test_and_set_bit(FE_FLAG_RESET_PENDING, priv->pending_flags))
+ schedule_work(&priv->pending_work);
+}
+
+static irqreturn_t fe_handle_irq(int irq, void *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ u32 status, int_mask;
+
+ status = fe_reg_r32(FE_REG_FE_INT_STATUS);
+
+ if (unlikely(!status))
+ return IRQ_NONE;
+
+ int_mask = (priv->soc->rx_int | priv->soc->tx_int);
+ if (likely(status & int_mask)) {
+ if (likely(napi_schedule_prep(&priv->rx_napi))) {
+ fe_int_disable(int_mask);
+ __napi_schedule(&priv->rx_napi);
+ }
+ } else {
+ fe_reg_w32(status, FE_REG_FE_INT_STATUS);
+ }
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void fe_poll_controller(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ u32 int_mask = priv->soc->tx_int | priv->soc->rx_int;
+
+ fe_int_disable(int_mask);
+ fe_handle_irq(dev->irq, dev);
+ fe_int_enable(int_mask);
+}
+#endif
+
+int fe_set_clock_cycle(struct fe_priv *priv)
+{
+ unsigned long sysclk = priv->sysclk;
+
+ if (!sysclk)
+ return -EINVAL;
+
+ sysclk /= FE_US_CYC_CNT_DIVISOR;
+ sysclk <<= FE_US_CYC_CNT_SHIFT;
+
+ fe_w32((fe_r32(FE_FE_GLO_CFG) &
+ ~(FE_US_CYC_CNT_MASK << FE_US_CYC_CNT_SHIFT)) |
+ sysclk,
+ FE_FE_GLO_CFG);
+ return 0;
+}
+
+void fe_fwd_config(struct fe_priv *priv)
+{
+ u32 fwd_cfg;
+
+ fwd_cfg = fe_r32(FE_GDMA1_FWD_CFG);
+
+ /* disable jumbo frame */
+ if (priv->flags & FE_FLAG_JUMBO_FRAME)
+ fwd_cfg &= ~FE_GDM1_JMB_EN;
+
+ /* set unicast/multicast/broadcast frame to cpu */
+ fwd_cfg &= ~0xffff;
+
+ fe_w32(fwd_cfg, FE_GDMA1_FWD_CFG);
+}
+
+static void fe_rxcsum_config(bool enable)
+{
+ if (enable)
+ fe_w32(fe_r32(FE_GDMA1_FWD_CFG) | (FE_GDM1_ICS_EN |
+ FE_GDM1_TCS_EN | FE_GDM1_UCS_EN),
+ FE_GDMA1_FWD_CFG);
+ else
+ fe_w32(fe_r32(FE_GDMA1_FWD_CFG) & ~(FE_GDM1_ICS_EN |
+ FE_GDM1_TCS_EN | FE_GDM1_UCS_EN),
+ FE_GDMA1_FWD_CFG);
+}
+
+static void fe_txcsum_config(bool enable)
+{
+ if (enable)
+ fe_w32(fe_r32(FE_CDMA_CSG_CFG) | (FE_ICS_GEN_EN |
+ FE_TCS_GEN_EN | FE_UCS_GEN_EN),
+ FE_CDMA_CSG_CFG);
+ else
+ fe_w32(fe_r32(FE_CDMA_CSG_CFG) & ~(FE_ICS_GEN_EN |
+ FE_TCS_GEN_EN | FE_UCS_GEN_EN),
+ FE_CDMA_CSG_CFG);
+}
+
+void fe_csum_config(struct fe_priv *priv)
+{
+ struct net_device *dev = priv_netdev(priv);
+
+ fe_txcsum_config((dev->features & NETIF_F_IP_CSUM));
+ fe_rxcsum_config((dev->features & NETIF_F_RXCSUM));
+}
+
+static int fe_hw_init(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ int i, err;
+
+ err = devm_request_irq(priv->device, dev->irq, fe_handle_irq, 0,
+ dev_name(priv->device), dev);
+ if (err)
+ return err;
+
+ if (priv->soc->set_mac)
+ priv->soc->set_mac(priv, dev->dev_addr);
+ else
+ fe_hw_set_macaddr(priv, dev->dev_addr);
+
+ /* disable delay interrupt */
+ fe_reg_w32(0, FE_REG_DLY_INT_CFG);
+
+ fe_int_disable(priv->soc->tx_int | priv->soc->rx_int);
+
+ /* frame engine will push VLAN tag regarding to VIDX feild in Tx desc */
+ if (fe_reg_table[FE_REG_FE_DMA_VID_BASE])
+ for (i = 0; i < 16; i += 2)
+ fe_w32(((i + 1) << 16) + i,
+ fe_reg_table[FE_REG_FE_DMA_VID_BASE] +
+ (i * 2));
+
+ if (priv->soc->fwd_config(priv))
+ netdev_err(dev, "unable to get clock\n");
+
+ if (fe_reg_table[FE_REG_FE_RST_GL]) {
+ fe_reg_w32(1, FE_REG_FE_RST_GL);
+ fe_reg_w32(0, FE_REG_FE_RST_GL);
+ }
+
+ return 0;
+}
+
+static int fe_open(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ unsigned long flags;
+ u32 val;
+ int err;
+
+ err = fe_init_dma(priv);
+ if (err)
+ goto err_out;
+
+ spin_lock_irqsave(&priv->page_lock, flags);
+
+ val = FE_TX_WB_DDONE | FE_RX_DMA_EN | FE_TX_DMA_EN;
+ if (priv->flags & FE_FLAG_RX_2B_OFFSET)
+ val |= FE_RX_2B_OFFSET;
+ val |= priv->soc->pdma_glo_cfg;
+ fe_reg_w32(val, FE_REG_PDMA_GLO_CFG);
+
+ spin_unlock_irqrestore(&priv->page_lock, flags);
+
+ if (priv->phy)
+ priv->phy->start(priv);
+
+ if (priv->soc->has_carrier && priv->soc->has_carrier(priv))
+ netif_carrier_on(dev);
+
+ napi_enable(&priv->rx_napi);
+ fe_int_enable(priv->soc->tx_int | priv->soc->rx_int);
+ netif_start_queue(dev);
+
+ return 0;
+
+err_out:
+ fe_free_dma(priv);
+ return err;
+}
+
+static int fe_stop(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ unsigned long flags;
+ int i;
+
+ netif_tx_disable(dev);
+ fe_int_disable(priv->soc->tx_int | priv->soc->rx_int);
+ napi_disable(&priv->rx_napi);
+
+ if (priv->phy)
+ priv->phy->stop(priv);
+
+ spin_lock_irqsave(&priv->page_lock, flags);
+
+ fe_reg_w32(fe_reg_r32(FE_REG_PDMA_GLO_CFG) &
+ ~(FE_TX_WB_DDONE | FE_RX_DMA_EN | FE_TX_DMA_EN),
+ FE_REG_PDMA_GLO_CFG);
+ spin_unlock_irqrestore(&priv->page_lock, flags);
+
+ /* wait dma stop */
+ for (i = 0; i < 10; i++) {
+ if (fe_reg_r32(FE_REG_PDMA_GLO_CFG) &
+ (FE_TX_DMA_BUSY | FE_RX_DMA_BUSY)) {
+ msleep(20);
+ continue;
+ }
+ break;
+ }
+
+ fe_free_dma(priv);
+
+ return 0;
+}
+
+static int __init fe_init(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ struct device_node *port;
+ const char *mac_addr;
+ int err;
+
+ priv->soc->reset_fe();
+
+ if (priv->soc->switch_init)
+ priv->soc->switch_init(priv);
+
+ mac_addr = of_get_mac_address(priv->device->of_node);
+ if (mac_addr)
+ ether_addr_copy(dev->dev_addr, mac_addr);
+
+ /*If the mac address is invalid, use random mac address */
+ if (!is_valid_ether_addr(dev->dev_addr)) {
+ random_ether_addr(dev->dev_addr);
+ dev_err(priv->device, "generated random MAC address %pM\n",
+ dev->dev_addr);
+ }
+
+ err = fe_mdio_init(priv);
+ if (err)
+ return err;
+
+ if (priv->soc->port_init)
+ for_each_child_of_node(priv->device->of_node, port)
+ if (of_device_is_compatible(port, "ralink,eth-port") &&
+ of_device_is_available(port))
+ priv->soc->port_init(priv, port);
+
+ if (priv->phy) {
+ err = priv->phy->connect(priv);
+ if (err)
+ goto err_phy_disconnect;
+ }
+
+ err = fe_hw_init(dev);
+ if (!err)
+ return 0;
+
+err_phy_disconnect:
+ if (priv->phy)
+ priv->phy->disconnect(priv);
+ fe_mdio_cleanup(priv);
+
+ return err;
+}
+
+static void fe_uninit(struct net_device *dev)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ if (priv->phy)
+ priv->phy->disconnect(priv);
+ fe_mdio_cleanup(priv);
+
+ fe_reg_w32(0, FE_REG_FE_INT_ENABLE);
+ free_irq(dev->irq, dev);
+}
+
+static int fe_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+
+ if (!priv->phy_dev)
+ return -ENODEV;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return phy_mii_ioctl(priv->phy_dev, ifr, cmd);
+ default:
+ break;
+ }
+
+ return -EOPNOTSUPP;
+}
+
+static int fe_change_mtu(struct net_device *dev, int new_mtu)
+{
+ struct fe_priv *priv = netdev_priv(dev);
+ int frag_size, old_mtu;
+ u32 fwd_cfg;
+
+ if (!(priv->flags & FE_FLAG_JUMBO_FRAME))
+ return eth_change_mtu(dev, new_mtu);
+
+ frag_size = fe_max_frag_size(new_mtu);
+ if (new_mtu < 68 || frag_size > PAGE_SIZE)
+ return -EINVAL;
+
+ old_mtu = dev->mtu;
+ dev->mtu = new_mtu;
+
+ /* return early if the buffer sizes will not change */
+ if (old_mtu <= ETH_DATA_LEN && new_mtu <= ETH_DATA_LEN)
+ return 0;
+ if (old_mtu > ETH_DATA_LEN && new_mtu > ETH_DATA_LEN)
+ return 0;
+
+ if (new_mtu <= ETH_DATA_LEN)
+ priv->rx_ring.frag_size = fe_max_frag_size(ETH_DATA_LEN);
+ else
+ priv->rx_ring.frag_size = PAGE_SIZE;
+ priv->rx_ring.rx_buf_size = fe_max_buf_size(priv->rx_ring.frag_size);
+
+ if (!netif_running(dev))
+ return 0;
+
+ fe_stop(dev);
+ fwd_cfg = fe_r32(FE_GDMA1_FWD_CFG);
+ if (new_mtu <= ETH_DATA_LEN) {
+ fwd_cfg &= ~FE_GDM1_JMB_EN;
+ } else {
+ fwd_cfg &= ~(FE_GDM1_JMB_LEN_MASK << FE_GDM1_JMB_LEN_SHIFT);
+ fwd_cfg |= (DIV_ROUND_UP(frag_size, 1024) <<
+ FE_GDM1_JMB_LEN_SHIFT) | FE_GDM1_JMB_EN;
+ }
+ fe_w32(fwd_cfg, FE_GDMA1_FWD_CFG);
+
+ return fe_open(dev);
+}
+
+static const struct net_device_ops fe_netdev_ops = {
+ .ndo_init = fe_init,
+ .ndo_uninit = fe_uninit,
+ .ndo_open = fe_open,
+ .ndo_stop = fe_stop,
+ .ndo_start_xmit = fe_start_xmit,
+ .ndo_set_mac_address = fe_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_do_ioctl = fe_do_ioctl,
+ .ndo_change_mtu = fe_change_mtu,
+ .ndo_tx_timeout = fe_tx_timeout,
+ .ndo_get_stats64 = fe_get_stats64,
+ .ndo_vlan_rx_add_vid = fe_vlan_rx_add_vid,
+ .ndo_vlan_rx_kill_vid = fe_vlan_rx_kill_vid,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = fe_poll_controller,
+#endif
+};
+
+static void fe_reset_pending(struct fe_priv *priv)
+{
+ struct net_device *dev = priv->netdev;
+ int err;
+
+ rtnl_lock();
+ fe_stop(dev);
+
+ err = fe_open(dev);
+ if (err)
+ goto error;
+ rtnl_unlock();
+
+ return;
+error:
+ netif_alert(priv, ifup, dev,
+ "Driver up/down cycle failed, closing device.\n");
+ dev_close(dev);
+ rtnl_unlock();
+}
+
+static const struct fe_work_t fe_work[] = {
+ {FE_FLAG_RESET_PENDING, fe_reset_pending},
+};
+
+static void fe_pending_work(struct work_struct *work)
+{
+ struct fe_priv *priv = container_of(work, struct fe_priv, pending_work);
+ int i;
+ bool pending;
+
+ for (i = 0; i < ARRAY_SIZE(fe_work); i++) {
+ pending = test_and_clear_bit(fe_work[i].bitnr,
+ priv->pending_flags);
+ if (pending)
+ fe_work[i].action(priv);
+ }
+}
+
+static int fe_probe(struct platform_device *pdev)
+{
+ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ const struct of_device_id *match;
+ struct fe_soc_data *soc;
+ struct net_device *netdev;
+ struct fe_priv *priv;
+ struct clk *sysclk;
+ int err, napi_weight;
+
+ device_reset(&pdev->dev);
+
+ match = of_match_device(of_fe_match, &pdev->dev);
+ soc = (struct fe_soc_data *)match->data;
+
+ if (soc->reg_table)
+ fe_reg_table = soc->reg_table;
+ else
+ soc->reg_table = fe_reg_table;
+
+ fe_base = devm_ioremap_resource(&pdev->dev, res);
+ if (!fe_base) {
+ err = -EADDRNOTAVAIL;
+ goto err_out;
+ }
+
+ netdev = alloc_etherdev(sizeof(*priv));
+ if (!netdev) {
+ dev_err(&pdev->dev, "alloc_etherdev failed\n");
+ err = -ENOMEM;
+ goto err_iounmap;
+ }
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+ netdev->netdev_ops = &fe_netdev_ops;
+ netdev->base_addr = (unsigned long)fe_base;
+
+ netdev->irq = platform_get_irq(pdev, 0);
+ if (netdev->irq < 0) {
+ dev_err(&pdev->dev, "no IRQ resource found\n");
+ err = -ENXIO;
+ goto err_free_dev;
+ }
+
+ if (soc->init_data)
+ soc->init_data(soc, netdev);
+ /* fake NETIF_F_HW_VLAN_CTAG_RX for good GRO performance */
+ netdev->hw_features |= NETIF_F_HW_VLAN_CTAG_RX;
+ netdev->vlan_features = netdev->hw_features &
+ ~(NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX);
+ netdev->features |= netdev->hw_features;
+
+ /* fake rx vlan filter func. to support tx vlan offload func */
+ if (fe_reg_table[FE_REG_FE_DMA_VID_BASE])
+ netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER;
+
+ priv = netdev_priv(netdev);
+ spin_lock_init(&priv->page_lock);
+ if (fe_reg_table[FE_REG_FE_COUNTER_BASE]) {
+ priv->hw_stats = kzalloc(sizeof(*priv->hw_stats), GFP_KERNEL);
+ if (!priv->hw_stats) {
+ err = -ENOMEM;
+ goto err_free_dev;
+ }
+ spin_lock_init(&priv->hw_stats->stats_lock);
+ }
+
+ sysclk = devm_clk_get(&pdev->dev, NULL);
+ if (!IS_ERR(sysclk))
+ priv->sysclk = clk_get_rate(sysclk);
+
+ priv->netdev = netdev;
+ priv->device = &pdev->dev;
+ priv->soc = soc;
+ priv->msg_enable = netif_msg_init(fe_msg_level, FE_DEFAULT_MSG_ENABLE);
+ priv->rx_ring.frag_size = fe_max_frag_size(ETH_DATA_LEN);
+ priv->rx_ring.rx_buf_size = fe_max_buf_size(priv->rx_ring.frag_size);
+ priv->tx_ring.tx_ring_size = NUM_DMA_DESC;
+ priv->rx_ring.rx_ring_size = NUM_DMA_DESC;
+ INIT_WORK(&priv->pending_work, fe_pending_work);
+
+ napi_weight = 32;
+ if (priv->flags & FE_FLAG_NAPI_WEIGHT) {
+ napi_weight *= 4;
+ priv->tx_ring.tx_ring_size *= 4;
+ priv->rx_ring.rx_ring_size *= 4;
+ }
+ netif_napi_add(netdev, &priv->rx_napi, fe_poll, napi_weight);
+ fe_set_ethtool_ops(netdev);
+
+ err = register_netdev(netdev);
+ if (err) {
+ dev_err(&pdev->dev, "error bringing up device\n");
+ goto err_free_dev;
+ }
+
+ platform_set_drvdata(pdev, netdev);
+
+ netif_info(priv, probe, netdev, "ralink at 0x%08lx, irq %d\n",
+ netdev->base_addr, netdev->irq);
+
+ return 0;
+
+err_free_dev:
+ free_netdev(netdev);
+err_iounmap:
+ devm_iounmap(&pdev->dev, fe_base);
+err_out:
+ return err;
+}
+
+static int fe_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct fe_priv *priv = netdev_priv(dev);
+
+ netif_napi_del(&priv->rx_napi);
+ kfree(priv->hw_stats);
+
+ cancel_work_sync(&priv->pending_work);
+
+ unregister_netdev(dev);
+ free_netdev(dev);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver fe_driver = {
+ .probe = fe_probe,
+ .remove = fe_remove,
+ .driver = {
+ .name = "ralink_soc_eth",
+ .owner = THIS_MODULE,
+ .of_match_table = of_fe_match,
+ },
+};
+
+static int __init init_rtfe(void)
+{
+ int ret;
+
+ ret = rtesw_init();
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&fe_driver);
+ if (ret)
+ rtesw_exit();
+
+ return ret;
+}
+
+static void __exit exit_rtfe(void)
+{
+ platform_driver_unregister(&fe_driver);
+ rtesw_exit();
+}
+
+module_init(init_rtfe);
+module_exit(exit_rtfe);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("John Crispin <blogic@openwrt.org>");
+MODULE_DESCRIPTION("Ethernet driver for Ralink SoC");
+MODULE_VERSION(FE_DRV_VERSION);
diff --git a/drivers/net/ethernet/ralink/ralink_soc_eth.h b/drivers/net/ethernet/ralink/ralink_soc_eth.h
new file mode 100644
index 0000000..55bd2c9
--- /dev/null
+++ b/drivers/net/ethernet/ralink/ralink_soc_eth.h
@@ -0,0 +1,519 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#ifndef FE_ETH_H
+#define FE_ETH_H
+
+#include <linux/mii.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/dma-mapping.h>
+#include <linux/phy.h>
+#include <linux/ethtool.h>
+#include <linux/version.h>
+
+enum fe_reg {
+ FE_REG_PDMA_GLO_CFG = 0,
+ FE_REG_PDMA_RST_CFG,
+ FE_REG_DLY_INT_CFG,
+ FE_REG_TX_BASE_PTR0,
+ FE_REG_TX_MAX_CNT0,
+ FE_REG_TX_CTX_IDX0,
+ FE_REG_TX_DTX_IDX0,
+ FE_REG_RX_BASE_PTR0,
+ FE_REG_RX_MAX_CNT0,
+ FE_REG_RX_CALC_IDX0,
+ FE_REG_RX_DRX_IDX0,
+ FE_REG_FE_INT_ENABLE,
+ FE_REG_FE_INT_STATUS,
+ FE_REG_FE_DMA_VID_BASE,
+ FE_REG_FE_COUNTER_BASE,
+ FE_REG_FE_RST_GL,
+ FE_REG_FE_INT_STATUS2,
+ FE_REG_COUNT
+};
+
+enum fe_work_flag {
+ FE_FLAG_RESET_PENDING,
+ FE_FLAG_MAX
+};
+
+#define FE_DRV_VERSION "0.1.2"
+
+/* power of 2 to let NEXT_TX_DESP_IDX work */
+#define NUM_DMA_DESC BIT(7)
+#define MAX_DMA_DESC 0xfff
+
+#define FE_DELAY_EN_INT 0x80
+#define FE_DELAY_MAX_INT 0x04
+#define FE_DELAY_MAX_TOUT 0x04
+#define FE_DELAY_TIME 20
+#define FE_DELAY_CHAN (((FE_DELAY_EN_INT | FE_DELAY_MAX_INT) << 8) | \
+ FE_DELAY_MAX_TOUT)
+#define FE_DELAY_INIT ((FE_DELAY_CHAN << 16) | FE_DELAY_CHAN)
+#define FE_PSE_FQFC_CFG_INIT 0x80504000
+#define FE_PSE_FQFC_CFG_256Q 0xff908000
+
+/* interrupt bits */
+#define FE_CNT_PPE_AF BIT(31)
+#define FE_CNT_GDM_AF BIT(29)
+#define FE_PSE_P2_FC BIT(26)
+#define FE_PSE_BUF_DROP BIT(24)
+#define FE_GDM_OTHER_DROP BIT(23)
+#define FE_PSE_P1_FC BIT(22)
+#define FE_PSE_P0_FC BIT(21)
+#define FE_PSE_FQ_EMPTY BIT(20)
+#define FE_GE1_STA_CHG BIT(18)
+#define FE_TX_COHERENT BIT(17)
+#define FE_RX_COHERENT BIT(16)
+#define FE_TX_DONE_INT3 BIT(11)
+#define FE_TX_DONE_INT2 BIT(10)
+#define FE_TX_DONE_INT1 BIT(9)
+#define FE_TX_DONE_INT0 BIT(8)
+#define FE_RX_DONE_INT0 BIT(2)
+#define FE_TX_DLY_INT BIT(1)
+#define FE_RX_DLY_INT BIT(0)
+
+#define FE_RX_DONE_INT FE_RX_DONE_INT0
+#define FE_TX_DONE_INT (FE_TX_DONE_INT0 | FE_TX_DONE_INT1 | \
+ FE_TX_DONE_INT2 | FE_TX_DONE_INT3)
+
+#define RT5350_RX_DLY_INT BIT(30)
+#define RT5350_TX_DLY_INT BIT(28)
+#define RT5350_RX_DONE_INT1 BIT(17)
+#define RT5350_RX_DONE_INT0 BIT(16)
+#define RT5350_TX_DONE_INT3 BIT(3)
+#define RT5350_TX_DONE_INT2 BIT(2)
+#define RT5350_TX_DONE_INT1 BIT(1)
+#define RT5350_TX_DONE_INT0 BIT(0)
+
+#define RT5350_RX_DONE_INT (RT5350_RX_DONE_INT0 | RT5350_RX_DONE_INT1)
+#define RT5350_TX_DONE_INT (RT5350_TX_DONE_INT0 | RT5350_TX_DONE_INT1 | \
+ RT5350_TX_DONE_INT2 | RT5350_TX_DONE_INT3)
+
+/* registers */
+#define FE_FE_OFFSET 0x0000
+#define FE_GDMA_OFFSET 0x0020
+#define FE_PSE_OFFSET 0x0040
+#define FE_GDMA2_OFFSET 0x0060
+#define FE_CDMA_OFFSET 0x0080
+#define FE_DMA_VID0 0x00a8
+#define FE_PDMA_OFFSET 0x0100
+#define FE_PPE_OFFSET 0x0200
+#define FE_CMTABLE_OFFSET 0x0400
+#define FE_POLICYTABLE_OFFSET 0x1000
+
+#define RT5350_PDMA_OFFSET 0x0800
+#define RT5350_SDM_OFFSET 0x0c00
+
+#define FE_MDIO_ACCESS (FE_FE_OFFSET + 0x00)
+#define FE_MDIO_CFG (FE_FE_OFFSET + 0x04)
+#define FE_FE_GLO_CFG (FE_FE_OFFSET + 0x08)
+#define FE_FE_RST_GL (FE_FE_OFFSET + 0x0C)
+#define FE_FE_INT_STATUS (FE_FE_OFFSET + 0x10)
+#define FE_FE_INT_ENABLE (FE_FE_OFFSET + 0x14)
+#define FE_MDIO_CFG2 (FE_FE_OFFSET + 0x18)
+#define FE_FOC_TS_T (FE_FE_OFFSET + 0x1C)
+
+#define FE_GDMA1_FWD_CFG (FE_GDMA_OFFSET + 0x00)
+#define FE_GDMA1_SCH_CFG (FE_GDMA_OFFSET + 0x04)
+#define FE_GDMA1_SHPR_CFG (FE_GDMA_OFFSET + 0x08)
+#define FE_GDMA1_MAC_ADRL (FE_GDMA_OFFSET + 0x0C)
+#define FE_GDMA1_MAC_ADRH (FE_GDMA_OFFSET + 0x10)
+
+#define FE_GDMA2_FWD_CFG (FE_GDMA2_OFFSET + 0x00)
+#define FE_GDMA2_SCH_CFG (FE_GDMA2_OFFSET + 0x04)
+#define FE_GDMA2_SHPR_CFG (FE_GDMA2_OFFSET + 0x08)
+#define FE_GDMA2_MAC_ADRL (FE_GDMA2_OFFSET + 0x0C)
+#define FE_GDMA2_MAC_ADRH (FE_GDMA2_OFFSET + 0x10)
+
+#define FE_PSE_FQ_CFG (FE_PSE_OFFSET + 0x00)
+#define FE_CDMA_FC_CFG (FE_PSE_OFFSET + 0x04)
+#define FE_GDMA1_FC_CFG (FE_PSE_OFFSET + 0x08)
+#define FE_GDMA2_FC_CFG (FE_PSE_OFFSET + 0x0C)
+
+#define FE_CDMA_CSG_CFG (FE_CDMA_OFFSET + 0x00)
+#define FE_CDMA_SCH_CFG (FE_CDMA_OFFSET + 0x04)
+
+#ifdef CONFIG_SOC_MT7621
+#define MT7620A_GDMA_OFFSET 0x0500
+#else
+#define MT7620A_GDMA_OFFSET 0x0600
+#endif
+#define MT7620A_GDMA1_FWD_CFG (MT7620A_GDMA_OFFSET + 0x00)
+#define MT7620A_FE_GDMA1_SCH_CFG (MT7620A_GDMA_OFFSET + 0x04)
+#define MT7620A_FE_GDMA1_SHPR_CFG (MT7620A_GDMA_OFFSET + 0x08)
+#define MT7620A_FE_GDMA1_MAC_ADRL (MT7620A_GDMA_OFFSET + 0x0C)
+#define MT7620A_FE_GDMA1_MAC_ADRH (MT7620A_GDMA_OFFSET + 0x10)
+
+#define RT5350_TX_BASE_PTR0 (RT5350_PDMA_OFFSET + 0x00)
+#define RT5350_TX_MAX_CNT0 (RT5350_PDMA_OFFSET + 0x04)
+#define RT5350_TX_CTX_IDX0 (RT5350_PDMA_OFFSET + 0x08)
+#define RT5350_TX_DTX_IDX0 (RT5350_PDMA_OFFSET + 0x0C)
+#define RT5350_TX_BASE_PTR1 (RT5350_PDMA_OFFSET + 0x10)
+#define RT5350_TX_MAX_CNT1 (RT5350_PDMA_OFFSET + 0x14)
+#define RT5350_TX_CTX_IDX1 (RT5350_PDMA_OFFSET + 0x18)
+#define RT5350_TX_DTX_IDX1 (RT5350_PDMA_OFFSET + 0x1C)
+#define RT5350_TX_BASE_PTR2 (RT5350_PDMA_OFFSET + 0x20)
+#define RT5350_TX_MAX_CNT2 (RT5350_PDMA_OFFSET + 0x24)
+#define RT5350_TX_CTX_IDX2 (RT5350_PDMA_OFFSET + 0x28)
+#define RT5350_TX_DTX_IDX2 (RT5350_PDMA_OFFSET + 0x2C)
+#define RT5350_TX_BASE_PTR3 (RT5350_PDMA_OFFSET + 0x30)
+#define RT5350_TX_MAX_CNT3 (RT5350_PDMA_OFFSET + 0x34)
+#define RT5350_TX_CTX_IDX3 (RT5350_PDMA_OFFSET + 0x38)
+#define RT5350_TX_DTX_IDX3 (RT5350_PDMA_OFFSET + 0x3C)
+#define RT5350_RX_BASE_PTR0 (RT5350_PDMA_OFFSET + 0x100)
+#define RT5350_RX_MAX_CNT0 (RT5350_PDMA_OFFSET + 0x104)
+#define RT5350_RX_CALC_IDX0 (RT5350_PDMA_OFFSET + 0x108)
+#define RT5350_RX_DRX_IDX0 (RT5350_PDMA_OFFSET + 0x10C)
+#define RT5350_RX_BASE_PTR1 (RT5350_PDMA_OFFSET + 0x110)
+#define RT5350_RX_MAX_CNT1 (RT5350_PDMA_OFFSET + 0x114)
+#define RT5350_RX_CALC_IDX1 (RT5350_PDMA_OFFSET + 0x118)
+#define RT5350_RX_DRX_IDX1 (RT5350_PDMA_OFFSET + 0x11C)
+#define RT5350_PDMA_GLO_CFG (RT5350_PDMA_OFFSET + 0x204)
+#define RT5350_PDMA_RST_CFG (RT5350_PDMA_OFFSET + 0x208)
+#define RT5350_DLY_INT_CFG (RT5350_PDMA_OFFSET + 0x20c)
+#define RT5350_FE_INT_STATUS (RT5350_PDMA_OFFSET + 0x220)
+#define RT5350_FE_INT_ENABLE (RT5350_PDMA_OFFSET + 0x228)
+#define RT5350_PDMA_SCH_CFG (RT5350_PDMA_OFFSET + 0x280)
+
+#define FE_PDMA_GLO_CFG (FE_PDMA_OFFSET + 0x00)
+#define FE_PDMA_RST_CFG (FE_PDMA_OFFSET + 0x04)
+#define FE_PDMA_SCH_CFG (FE_PDMA_OFFSET + 0x08)
+#define FE_DLY_INT_CFG (FE_PDMA_OFFSET + 0x0C)
+#define FE_TX_BASE_PTR0 (FE_PDMA_OFFSET + 0x10)
+#define FE_TX_MAX_CNT0 (FE_PDMA_OFFSET + 0x14)
+#define FE_TX_CTX_IDX0 (FE_PDMA_OFFSET + 0x18)
+#define FE_TX_DTX_IDX0 (FE_PDMA_OFFSET + 0x1C)
+#define FE_TX_BASE_PTR1 (FE_PDMA_OFFSET + 0x20)
+#define FE_TX_MAX_CNT1 (FE_PDMA_OFFSET + 0x24)
+#define FE_TX_CTX_IDX1 (FE_PDMA_OFFSET + 0x28)
+#define FE_TX_DTX_IDX1 (FE_PDMA_OFFSET + 0x2C)
+#define FE_RX_BASE_PTR0 (FE_PDMA_OFFSET + 0x30)
+#define FE_RX_MAX_CNT0 (FE_PDMA_OFFSET + 0x34)
+#define FE_RX_CALC_IDX0 (FE_PDMA_OFFSET + 0x38)
+#define FE_RX_DRX_IDX0 (FE_PDMA_OFFSET + 0x3C)
+#define FE_TX_BASE_PTR2 (FE_PDMA_OFFSET + 0x40)
+#define FE_TX_MAX_CNT2 (FE_PDMA_OFFSET + 0x44)
+#define FE_TX_CTX_IDX2 (FE_PDMA_OFFSET + 0x48)
+#define FE_TX_DTX_IDX2 (FE_PDMA_OFFSET + 0x4C)
+#define FE_TX_BASE_PTR3 (FE_PDMA_OFFSET + 0x50)
+#define FE_TX_MAX_CNT3 (FE_PDMA_OFFSET + 0x54)
+#define FE_TX_CTX_IDX3 (FE_PDMA_OFFSET + 0x58)
+#define FE_TX_DTX_IDX3 (FE_PDMA_OFFSET + 0x5C)
+#define FE_RX_BASE_PTR1 (FE_PDMA_OFFSET + 0x60)
+#define FE_RX_MAX_CNT1 (FE_PDMA_OFFSET + 0x64)
+#define FE_RX_CALC_IDX1 (FE_PDMA_OFFSET + 0x68)
+#define FE_RX_DRX_IDX1 (FE_PDMA_OFFSET + 0x6C)
+
+/* Switch DMA configuration */
+#define RT5350_SDM_CFG (RT5350_SDM_OFFSET + 0x00)
+#define RT5350_SDM_RRING (RT5350_SDM_OFFSET + 0x04)
+#define RT5350_SDM_TRING (RT5350_SDM_OFFSET + 0x08)
+#define RT5350_SDM_MAC_ADRL (RT5350_SDM_OFFSET + 0x0C)
+#define RT5350_SDM_MAC_ADRH (RT5350_SDM_OFFSET + 0x10)
+#define RT5350_SDM_TPCNT (RT5350_SDM_OFFSET + 0x100)
+#define RT5350_SDM_TBCNT (RT5350_SDM_OFFSET + 0x104)
+#define RT5350_SDM_RPCNT (RT5350_SDM_OFFSET + 0x108)
+#define RT5350_SDM_RBCNT (RT5350_SDM_OFFSET + 0x10C)
+#define RT5350_SDM_CS_ERR (RT5350_SDM_OFFSET + 0x110)
+
+#define RT5350_SDM_ICS_EN BIT(16)
+#define RT5350_SDM_TCS_EN BIT(17)
+#define RT5350_SDM_UCS_EN BIT(18)
+
+/* MDIO_CFG register bits */
+#define FE_MDIO_CFG_AUTO_POLL_EN BIT(29)
+#define FE_MDIO_CFG_GP1_BP_EN BIT(16)
+#define FE_MDIO_CFG_GP1_FRC_EN BIT(15)
+#define FE_MDIO_CFG_GP1_SPEED_10 (0 << 13)
+#define FE_MDIO_CFG_GP1_SPEED_100 (1 << 13)
+#define FE_MDIO_CFG_GP1_SPEED_1000 (2 << 13)
+#define FE_MDIO_CFG_GP1_DUPLEX BIT(12)
+#define FE_MDIO_CFG_GP1_FC_TX BIT(11)
+#define FE_MDIO_CFG_GP1_FC_RX BIT(10)
+#define FE_MDIO_CFG_GP1_LNK_DWN BIT(9)
+#define FE_MDIO_CFG_GP1_AN_FAIL BIT(8)
+#define FE_MDIO_CFG_MDC_CLK_DIV_1 (0 << 6)
+#define FE_MDIO_CFG_MDC_CLK_DIV_2 (1 << 6)
+#define FE_MDIO_CFG_MDC_CLK_DIV_4 (2 << 6)
+#define FE_MDIO_CFG_MDC_CLK_DIV_8 (3 << 6)
+#define FE_MDIO_CFG_TURBO_MII_FREQ BIT(5)
+#define FE_MDIO_CFG_TURBO_MII_MODE BIT(4)
+#define FE_MDIO_CFG_RX_CLK_SKEW_0 (0 << 2)
+#define FE_MDIO_CFG_RX_CLK_SKEW_200 (1 << 2)
+#define FE_MDIO_CFG_RX_CLK_SKEW_400 (2 << 2)
+#define FE_MDIO_CFG_RX_CLK_SKEW_INV (3 << 2)
+#define FE_MDIO_CFG_TX_CLK_SKEW_0 0
+#define FE_MDIO_CFG_TX_CLK_SKEW_200 1
+#define FE_MDIO_CFG_TX_CLK_SKEW_400 2
+#define FE_MDIO_CFG_TX_CLK_SKEW_INV 3
+
+/* uni-cast port */
+#define FE_GDM1_JMB_LEN_MASK 0xf
+#define FE_GDM1_JMB_LEN_SHIFT 28
+#define FE_GDM1_ICS_EN BIT(22)
+#define FE_GDM1_TCS_EN BIT(21)
+#define FE_GDM1_UCS_EN BIT(20)
+#define FE_GDM1_JMB_EN BIT(19)
+#define FE_GDM1_STRPCRC BIT(16)
+#define FE_GDM1_UFRC_P_CPU (0 << 12)
+#define FE_GDM1_UFRC_P_GDMA1 (1 << 12)
+#define FE_GDM1_UFRC_P_PPE (6 << 12)
+
+/* checksums */
+#define FE_ICS_GEN_EN BIT(2)
+#define FE_UCS_GEN_EN BIT(1)
+#define FE_TCS_GEN_EN BIT(0)
+
+/* dma ring */
+#define FE_PST_DRX_IDX0 BIT(16)
+#define FE_PST_DTX_IDX3 BIT(3)
+#define FE_PST_DTX_IDX2 BIT(2)
+#define FE_PST_DTX_IDX1 BIT(1)
+#define FE_PST_DTX_IDX0 BIT(0)
+
+#define FE_RX_2B_OFFSET BIT(31)
+#define FE_TX_WB_DDONE BIT(6)
+#define FE_RX_DMA_BUSY BIT(3)
+#define FE_TX_DMA_BUSY BIT(1)
+#define FE_RX_DMA_EN BIT(2)
+#define FE_TX_DMA_EN BIT(0)
+
+#define FE_PDMA_SIZE_4DWORDS (0 << 4)
+#define FE_PDMA_SIZE_8DWORDS (1 << 4)
+#define FE_PDMA_SIZE_16DWORDS (2 << 4)
+
+#define FE_US_CYC_CNT_MASK 0xff
+#define FE_US_CYC_CNT_SHIFT 0x8
+#define FE_US_CYC_CNT_DIVISOR 1000000
+
+/* rxd2 */
+#define RX_DMA_DONE BIT(31)
+#define RX_DMA_LSO BIT(30)
+#define RX_DMA_PLEN0(_x) (((_x) & 0x3fff) << 16)
+#define RX_DMA_GET_PLEN0(_x) (((_x) >> 16) & 0x3fff)
+#define RX_DMA_TAG BIT(15)
+/* rxd3 */
+#define RX_DMA_TPID(_x) (((_x) >> 16) & 0xffff)
+#define RX_DMA_VID(_x) ((_x) & 0xffff)
+/* rxd4 */
+#define RX_DMA_L4VALID BIT(30)
+
+struct fe_rx_dma {
+ unsigned int rxd1;
+ unsigned int rxd2;
+ unsigned int rxd3;
+ unsigned int rxd4;
+} __packed __aligned(4);
+
+#define TX_DMA_BUF_LEN 0x3fff
+#define TX_DMA_PLEN0_MASK (TX_DMA_BUF_LEN << 16)
+#define TX_DMA_PLEN0(_x) (((_x) & TX_DMA_BUF_LEN) << 16)
+#define TX_DMA_PLEN1(_x) ((_x) & TX_DMA_BUF_LEN)
+#define TX_DMA_GET_PLEN0(_x) (((_x) >> 16) & TX_DMA_BUF_LEN)
+#define TX_DMA_GET_PLEN1(_x) ((_x) & TX_DMA_BUF_LEN)
+#define TX_DMA_LS1 BIT(14)
+#define TX_DMA_LS0 BIT(30)
+#define TX_DMA_DONE BIT(31)
+
+#define TX_DMA_INS_VLAN_MT7621 BIT(16)
+#define TX_DMA_INS_VLAN BIT(7)
+#define TX_DMA_INS_PPPOE BIT(12)
+#define TX_DMA_QN(_x) ((_x) << 16)
+#define TX_DMA_PN(_x) ((_x) << 24)
+#define TX_DMA_QN_MASK TX_DMA_QN(0x7)
+#define TX_DMA_PN_MASK TX_DMA_PN(0x7)
+#define TX_DMA_UDF BIT(20)
+#define TX_DMA_CHKSUM (0x7 << 29)
+#define TX_DMA_TSO BIT(28)
+
+/* frame engine counters */
+#define FE_PPE_AC_BCNT0 (FE_CMTABLE_OFFSET + 0x00)
+#define FE_GDMA1_TX_GBCNT (FE_CMTABLE_OFFSET + 0x300)
+#define FE_GDMA2_TX_GBCNT (FE_GDMA1_TX_GBCNT + 0x40)
+
+/* phy device flags */
+#define FE_PHY_FLAG_PORT BIT(0)
+#define FE_PHY_FLAG_ATTACH BIT(1)
+
+struct fe_tx_dma {
+ unsigned int txd1;
+ unsigned int txd2;
+ unsigned int txd3;
+ unsigned int txd4;
+} __packed __aligned(4);
+
+struct fe_priv;
+
+struct fe_phy {
+ /* make sure that phy operations are atomic */
+ spinlock_t lock;
+
+ struct phy_device *phy[8];
+ struct device_node *phy_node[8];
+ const __be32 *phy_fixed[8];
+ int duplex[8];
+ int speed[8];
+ int tx_fc[8];
+ int rx_fc[8];
+ int (*connect)(struct fe_priv *priv);
+ void (*disconnect)(struct fe_priv *priv);
+ void (*start)(struct fe_priv *priv);
+ void (*stop)(struct fe_priv *priv);
+};
+
+struct fe_soc_data {
+ const u16 *reg_table;
+
+ void (*init_data)(struct fe_soc_data *data, struct net_device *netdev);
+ void (*reset_fe)(void);
+ void (*set_mac)(struct fe_priv *priv, unsigned char *mac);
+ int (*fwd_config)(struct fe_priv *priv);
+ void (*tx_dma)(struct fe_tx_dma *txd);
+ int (*switch_init)(struct fe_priv *priv);
+ void (*port_init)(struct fe_priv *priv, struct device_node *port);
+ int (*has_carrier)(struct fe_priv *priv);
+ int (*mdio_init)(struct fe_priv *priv);
+ void (*mdio_cleanup)(struct fe_priv *priv);
+ int (*mdio_write)(struct mii_bus *bus, int phy_addr, int phy_reg,
+ u16 val);
+ int (*mdio_read)(struct mii_bus *bus, int phy_addr, int phy_reg);
+ void (*mdio_adjust_link)(struct fe_priv *priv, int port);
+
+ void *swpriv;
+ u32 pdma_glo_cfg;
+ u32 rx_int;
+ u32 tx_int;
+ u32 status_int;
+ u32 checksum_bit;
+};
+
+#define FE_FLAG_PADDING_64B BIT(0)
+#define FE_FLAG_PADDING_BUG BIT(1)
+#define FE_FLAG_JUMBO_FRAME BIT(2)
+#define FE_FLAG_RX_2B_OFFSET BIT(3)
+#define FE_FLAG_RX_SG_DMA BIT(4)
+#define FE_FLAG_RX_VLAN_CTAG BIT(5)
+#define FE_FLAG_NAPI_WEIGHT BIT(6)
+
+#define FE_STAT_REG_DECLARE \
+ _FE(tx_bytes) \
+ _FE(tx_packets) \
+ _FE(tx_skip) \
+ _FE(tx_collisions) \
+ _FE(rx_bytes) \
+ _FE(rx_packets) \
+ _FE(rx_overflow) \
+ _FE(rx_fcs_errors) \
+ _FE(rx_short_errors) \
+ _FE(rx_long_errors) \
+ _FE(rx_checksum_errors) \
+ _FE(rx_flow_control_packets)
+
+struct fe_hw_stats {
+ /* make sure that stats operations are atomic */
+ spinlock_t stats_lock;
+
+ struct u64_stats_sync syncp;
+#define _FE(x) u64 x;
+ FE_STAT_REG_DECLARE
+#undef _FE
+};
+
+enum fe_tx_flags {
+ FE_TX_FLAGS_SINGLE0 = 0x01,
+ FE_TX_FLAGS_PAGE0 = 0x02,
+ FE_TX_FLAGS_PAGE1 = 0x04,
+};
+
+struct fe_tx_buf {
+ struct sk_buff *skb;
+ u32 flags;
+ DEFINE_DMA_UNMAP_ADDR(dma_addr0);
+ DEFINE_DMA_UNMAP_LEN(dma_len0);
+ DEFINE_DMA_UNMAP_ADDR(dma_addr1);
+ DEFINE_DMA_UNMAP_LEN(dma_len1);
+};
+
+struct fe_tx_ring {
+ struct fe_tx_dma *tx_dma;
+ struct fe_tx_buf *tx_buf;
+ dma_addr_t tx_phys;
+ u16 tx_ring_size;
+ u16 tx_free_idx;
+ u16 tx_next_idx;
+ u16 tx_thresh;
+};
+
+struct fe_rx_ring {
+ struct fe_rx_dma *rx_dma;
+ u8 **rx_data;
+ dma_addr_t rx_phys;
+ u16 rx_ring_size;
+ u16 frag_size;
+ u16 rx_buf_size;
+ u16 rx_calc_idx;
+};
+
+struct fe_priv {
+ /* make sure that register operations are atomic */
+ spinlock_t page_lock;
+
+ struct fe_soc_data *soc;
+ struct net_device *netdev;
+ u32 msg_enable;
+ u32 flags;
+
+ struct device *device;
+ unsigned long sysclk;
+
+ struct fe_rx_ring rx_ring;
+ struct napi_struct rx_napi;
+
+ struct fe_tx_ring tx_ring;
+
+ struct fe_phy *phy;
+ struct mii_bus *mii_bus;
+ struct phy_device *phy_dev;
+ u32 phy_flags;
+
+ int link[8];
+
+ struct fe_hw_stats *hw_stats;
+ unsigned long vlan_map;
+ struct work_struct pending_work;
+ DECLARE_BITMAP(pending_flags, FE_FLAG_MAX);
+};
+
+extern const struct of_device_id of_fe_match[];
+
+void fe_w32(u32 val, unsigned reg);
+u32 fe_r32(unsigned reg);
+
+int fe_set_clock_cycle(struct fe_priv *priv);
+void fe_csum_config(struct fe_priv *priv);
+void fe_stats_update(struct fe_priv *priv);
+void fe_fwd_config(struct fe_priv *priv);
+void fe_reg_w32(u32 val, enum fe_reg reg);
+u32 fe_reg_r32(enum fe_reg reg);
+
+void fe_reset(u32 reset_bits);
+
+static inline void *priv_netdev(struct fe_priv *priv)
+{
+ return (char *)priv - ALIGN(sizeof(struct net_device), NETDEV_ALIGN);
+}
+
+#endif /* FE_ETH_H */
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 4/8] net-next: ralink: add support for rt2880
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
2015-11-22 8:40 ` [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached John Crispin
2015-11-22 8:40 ` [RFC 3/8] net-next: ralink: add the drivers core files John Crispin
@ 2015-11-22 8:40 ` John Crispin
2015-11-22 8:40 ` [RFC 5/8] net-next: ralink: add support for rt3050 family John Crispin
` (3 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
rt2880 is the oldest SoC with this core. It has a single gBit port that will
normally be attached to an external phy of switch. The patch also adds the
code required to drive the mdio bus.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
---
drivers/net/ethernet/ralink/mdio_rt2880.c | 231 +++++++++++++++++++++++++++++
drivers/net/ethernet/ralink/mdio_rt2880.h | 23 +++
drivers/net/ethernet/ralink/soc_rt2880.c | 76 ++++++++++
3 files changed, 330 insertions(+)
create mode 100644 drivers/net/ethernet/ralink/mdio_rt2880.c
create mode 100644 drivers/net/ethernet/ralink/mdio_rt2880.h
create mode 100644 drivers/net/ethernet/ralink/soc_rt2880.c
diff --git a/drivers/net/ethernet/ralink/mdio_rt2880.c b/drivers/net/ethernet/ralink/mdio_rt2880.c
new file mode 100644
index 0000000..f3d19f0
--- /dev/null
+++ b/drivers/net/ethernet/ralink/mdio_rt2880.c
@@ -0,0 +1,231 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/skbuff.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+
+#include "ralink_soc_eth.h"
+#include "mdio_rt2880.h"
+#include "mdio.h"
+
+#define FE_MDIO_RETRY 1000
+
+static unsigned char *rt2880_speed_str(struct fe_priv *priv)
+{
+ switch (priv->phy->speed[0]) {
+ case SPEED_1000:
+ return "1000";
+ case SPEED_100:
+ return "100";
+ case SPEED_10:
+ return "10";
+ }
+
+ return "?";
+}
+
+void rt2880_mdio_link_adjust(struct fe_priv *priv, int port)
+{
+ u32 mdio_cfg;
+
+ if (!priv->link[0]) {
+ netif_carrier_off(priv->netdev);
+ netdev_info(priv->netdev, "link down\n");
+ return;
+ }
+
+ mdio_cfg = FE_MDIO_CFG_TX_CLK_SKEW_200 |
+ FE_MDIO_CFG_RX_CLK_SKEW_200 |
+ FE_MDIO_CFG_GP1_FRC_EN;
+
+ if (priv->phy->duplex[0] == DUPLEX_FULL)
+ mdio_cfg |= FE_MDIO_CFG_GP1_DUPLEX;
+
+ if (priv->phy->tx_fc[0])
+ mdio_cfg |= FE_MDIO_CFG_GP1_FC_TX;
+
+ if (priv->phy->rx_fc[0])
+ mdio_cfg |= FE_MDIO_CFG_GP1_FC_RX;
+
+ switch (priv->phy->speed[0]) {
+ case SPEED_10:
+ mdio_cfg |= FE_MDIO_CFG_GP1_SPEED_10;
+ break;
+ case SPEED_100:
+ mdio_cfg |= FE_MDIO_CFG_GP1_SPEED_100;
+ break;
+ case SPEED_1000:
+ mdio_cfg |= FE_MDIO_CFG_GP1_SPEED_1000;
+ break;
+ default:
+ BUG();
+ }
+
+ fe_w32(mdio_cfg, FE_MDIO_CFG);
+
+ netif_carrier_on(priv->netdev);
+ netdev_info(priv->netdev, "link up (%sMbps/%s duplex)\n",
+ rt2880_speed_str(priv),
+ (priv->phy->duplex[0] == DUPLEX_FULL) ? "Full" : "Half");
+}
+
+static int rt2880_mdio_wait_ready(struct fe_priv *priv)
+{
+ int retries;
+
+ retries = FE_MDIO_RETRY;
+ while (1) {
+ u32 t;
+
+ t = fe_r32(FE_MDIO_ACCESS);
+ if ((t & BIT(31)) == 0)
+ return 0;
+
+ if (retries-- == 0)
+ break;
+
+ udelay(1);
+ }
+
+ dev_err(priv->device, "MDIO operation timed out\n");
+ return -ETIMEDOUT;
+}
+
+int rt2880_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg)
+{
+ struct fe_priv *priv = bus->priv;
+ int err;
+ u32 t;
+
+ err = rt2880_mdio_wait_ready(priv);
+ if (err)
+ return 0xffff;
+
+ t = (phy_addr << 24) | (phy_reg << 16);
+ fe_w32(t, FE_MDIO_ACCESS);
+ t |= BIT(31);
+ fe_w32(t, FE_MDIO_ACCESS);
+
+ err = rt2880_mdio_wait_ready(priv);
+ if (err)
+ return 0xffff;
+
+ pr_debug("%s: addr=%04x, reg=%04x, value=%04x\n", __func__,
+ phy_addr, phy_reg, fe_r32(FE_MDIO_ACCESS) & 0xffff);
+
+ return fe_r32(FE_MDIO_ACCESS) & 0xffff;
+}
+
+int rt2880_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, u16 val)
+{
+ struct fe_priv *priv = bus->priv;
+ int err;
+ u32 t;
+
+ pr_debug("%s: addr=%04x, reg=%04x, value=%04x\n", __func__,
+ phy_addr, phy_reg, fe_r32(FE_MDIO_ACCESS) & 0xffff);
+
+ err = rt2880_mdio_wait_ready(priv);
+ if (err)
+ return err;
+
+ t = (1 << 30) | (phy_addr << 24) | (phy_reg << 16) | val;
+ fe_w32(t, FE_MDIO_ACCESS);
+ t |= BIT(31);
+ fe_w32(t, FE_MDIO_ACCESS);
+
+ return rt2880_mdio_wait_ready(priv);
+}
+
+void rt2880_port_init(struct fe_priv *priv, struct device_node *np)
+{
+ const __be32 *id = of_get_property(np, "reg", NULL);
+ const __be32 *link;
+ int size;
+ int phy_mode;
+
+ if (!id || (be32_to_cpu(*id) != 0)) {
+ pr_err("%s: invalid port id\n", np->name);
+ return;
+ }
+
+ priv->phy->phy_fixed[0] = of_get_property(np,
+ "ralink,fixed-link", &size);
+ if (priv->phy->phy_fixed[0] &&
+ (size != (4 * sizeof(*priv->phy->phy_fixed[0])))) {
+ pr_err("%s: invalid fixed link property\n", np->name);
+ priv->phy->phy_fixed[0] = NULL;
+ return;
+ }
+
+ phy_mode = of_get_phy_mode(np);
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_RGMII:
+ break;
+ case PHY_INTERFACE_MODE_MII:
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ break;
+ default:
+ if (!priv->phy->phy_fixed[0])
+ dev_err(priv->device, "port %d - invalid phy mode\n",
+ priv->phy->speed[0]);
+ break;
+ }
+
+ priv->phy->phy_node[0] = of_parse_phandle(np, "phy-handle", 0);
+ if (!priv->phy->phy_node[0] && !priv->phy->phy_fixed[0])
+ return;
+
+ if (priv->phy->phy_fixed[0]) {
+ link = priv->phy->phy_fixed[0];
+ priv->phy->speed[0] = be32_to_cpup(link++);
+ priv->phy->duplex[0] = be32_to_cpup(link++);
+ priv->phy->tx_fc[0] = be32_to_cpup(link++);
+ priv->phy->rx_fc[0] = be32_to_cpup(link++);
+
+ priv->link[0] = 1;
+ switch (priv->phy->speed[0]) {
+ case SPEED_10:
+ break;
+ case SPEED_100:
+ break;
+ case SPEED_1000:
+ break;
+ default:
+ dev_err(priv->device, "invalid link speed: %d\n",
+ priv->phy->speed[0]);
+ priv->phy->phy_fixed[0] = 0;
+ return;
+ }
+ dev_info(priv->device, "using fixed link parameters\n");
+ rt2880_mdio_link_adjust(priv, 0);
+ return;
+ }
+
+ if (priv->phy->phy_node[0] && priv->mii_bus->phy_map[0])
+ fe_connect_phy_node(priv, priv->phy->phy_node[0]);
+}
diff --git a/drivers/net/ethernet/ralink/mdio_rt2880.h b/drivers/net/ethernet/ralink/mdio_rt2880.h
new file mode 100644
index 0000000..6884894
--- /dev/null
+++ b/drivers/net/ethernet/ralink/mdio_rt2880.h
@@ -0,0 +1,23 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#ifndef _RALINK_MDIO_RT2880_H__
+#define _RALINK_MDIO_RT2880_H__
+
+void rt2880_mdio_link_adjust(struct fe_priv *priv, int port);
+int rt2880_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg);
+int rt2880_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, u16 val);
+void rt2880_port_init(struct fe_priv *priv, struct device_node *np);
+
+#endif
diff --git a/drivers/net/ethernet/ralink/soc_rt2880.c b/drivers/net/ethernet/ralink/soc_rt2880.c
new file mode 100644
index 0000000..eb9b9c2
--- /dev/null
+++ b/drivers/net/ethernet/ralink/soc_rt2880.c
@@ -0,0 +1,76 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "ralink_soc_eth.h"
+#include "mdio_rt2880.h"
+
+#define RT2880_RESET_FE BIT(18)
+
+static void rt2880_init_data(struct fe_soc_data *data,
+ struct net_device *netdev)
+{
+ struct fe_priv *priv = netdev_priv(netdev);
+
+ priv->flags = FE_FLAG_PADDING_64B | FE_FLAG_PADDING_BUG |
+ FE_FLAG_JUMBO_FRAME;
+ netdev->hw_features = NETIF_F_SG | NETIF_F_HW_VLAN_CTAG_TX;
+ /* this should work according to the datasheet but actually does not*/
+ /* netdev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_RXCSUM; */
+}
+
+void rt2880_fe_reset(void)
+{
+ fe_reset(RT2880_RESET_FE);
+}
+
+static int rt2880_fwd_config(struct fe_priv *priv)
+{
+ int ret;
+
+ ret = fe_set_clock_cycle(priv);
+ if (ret)
+ return ret;
+
+ fe_fwd_config(priv);
+ fe_w32(FE_PSE_FQFC_CFG_INIT, FE_PSE_FQ_CFG);
+ fe_csum_config(priv);
+
+ return ret;
+}
+
+struct fe_soc_data rt2880_data = {
+ .init_data = rt2880_init_data,
+ .reset_fe = rt2880_fe_reset,
+ .fwd_config = rt2880_fwd_config,
+ .pdma_glo_cfg = FE_PDMA_SIZE_8DWORDS,
+ .checksum_bit = RX_DMA_L4VALID,
+ .rx_int = FE_RX_DONE_INT,
+ .tx_int = FE_TX_DONE_INT,
+ .status_int = FE_CNT_GDM_AF,
+ .mdio_read = rt2880_mdio_read,
+ .mdio_write = rt2880_mdio_write,
+ .mdio_adjust_link = rt2880_mdio_link_adjust,
+ .port_init = rt2880_port_init,
+};
+
+const struct of_device_id of_fe_match[] = {
+ { .compatible = "ralink,rt2880-eth", .data = &rt2880_data },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, of_fe_match);
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 5/8] net-next: ralink: add support for rt3050 family
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
` (2 preceding siblings ...)
2015-11-22 8:40 ` [RFC 4/8] net-next: ralink: add support for rt2880 John Crispin
@ 2015-11-22 8:40 ` John Crispin
2015-11-22 16:36 ` Andrew Lunn
2015-11-22 8:40 ` [RFC 6/8] net-next: ralink: add support for rt3883 John Crispin
` (2 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
Add support for SoCs from the rt3050 family. This include rt3050, rt3052,
rt3352 and rt5350. These all have a builtin 5 port 100mbit switch. This patch
includes rudimentary code to power up the switch. There are a lot of magic
values that get written to the switch and the internal phys. These values
come straight from the SDK driver and we do not know the meaning of most of
them.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
---
drivers/net/ethernet/ralink/esw_rt3050.c | 682 ++++++++++++++++++++++++++++++
drivers/net/ethernet/ralink/esw_rt3050.h | 29 ++
drivers/net/ethernet/ralink/soc_rt3050.c | 154 +++++++
3 files changed, 865 insertions(+)
create mode 100644 drivers/net/ethernet/ralink/esw_rt3050.c
create mode 100644 drivers/net/ethernet/ralink/esw_rt3050.h
create mode 100644 drivers/net/ethernet/ralink/soc_rt3050.c
diff --git a/drivers/net/ethernet/ralink/esw_rt3050.c b/drivers/net/ethernet/ralink/esw_rt3050.c
new file mode 100644
index 0000000..aae6dac
--- /dev/null
+++ b/drivers/net/ethernet/ralink/esw_rt3050.c
@@ -0,0 +1,682 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/skbuff.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "ralink_soc_eth.h"
+
+#include <linux/ioport.h>
+#include <linux/mii.h>
+
+#include <ralink_regs.h>
+
+/* HW limitations for this switch:
+ * - No large frame support (PKT_MAX_LEN at most 1536)
+ * - Can't have untagged vlan and tagged vlan on one port at the same time,
+ * though this might be possible using the undocumented PPE.
+ */
+
+#define RT305X_ESW_REG_ISR 0x00
+#define RT305X_ESW_REG_IMR 0x04
+#define RT305X_ESW_REG_FCT0 0x08
+#define RT305X_ESW_REG_PFC1 0x14
+#define RT305X_ESW_REG_ATS 0x24
+#define RT305X_ESW_REG_ATS0 0x28
+#define RT305X_ESW_REG_ATS1 0x2c
+#define RT305X_ESW_REG_ATS2 0x30
+#define RT305X_ESW_REG_PVIDC(_n) (0x40 + 4 * (_n))
+#define RT305X_ESW_REG_VLANI(_n) (0x50 + 4 * (_n))
+#define RT305X_ESW_REG_VMSC(_n) (0x70 + 4 * (_n))
+#define RT305X_ESW_REG_POA 0x80
+#define RT305X_ESW_REG_FPA 0x84
+#define RT305X_ESW_REG_SOCPC 0x8c
+#define RT305X_ESW_REG_POC0 0x90
+#define RT305X_ESW_REG_POC1 0x94
+#define RT305X_ESW_REG_POC2 0x98
+#define RT305X_ESW_REG_SGC 0x9c
+#define RT305X_ESW_REG_STRT 0xa0
+#define RT305X_ESW_REG_PCR0 0xc0
+#define RT305X_ESW_REG_PCR1 0xc4
+#define RT305X_ESW_REG_FPA2 0xc8
+#define RT305X_ESW_REG_FCT2 0xcc
+#define RT305X_ESW_REG_SGC2 0xe4
+#define RT305X_ESW_REG_P0LED 0xa4
+#define RT305X_ESW_REG_P1LED 0xa8
+#define RT305X_ESW_REG_P2LED 0xac
+#define RT305X_ESW_REG_P3LED 0xb0
+#define RT305X_ESW_REG_P4LED 0xb4
+#define RT305X_ESW_REG_PXPC(_x) (0xe8 + (4 * _x))
+#define RT305X_ESW_REG_P1PC 0xec
+#define RT305X_ESW_REG_P2PC 0xf0
+#define RT305X_ESW_REG_P3PC 0xf4
+#define RT305X_ESW_REG_P4PC 0xf8
+#define RT305X_ESW_REG_P5PC 0xfc
+
+#define RT305X_ESW_LED_LINK 0
+#define RT305X_ESW_LED_100M 1
+#define RT305X_ESW_LED_DUPLEX 2
+#define RT305X_ESW_LED_ACTIVITY 3
+#define RT305X_ESW_LED_COLLISION 4
+#define RT305X_ESW_LED_LINKACT 5
+#define RT305X_ESW_LED_DUPLCOLL 6
+#define RT305X_ESW_LED_10MACT 7
+#define RT305X_ESW_LED_100MACT 8
+/* Additional led states not in datasheet: */
+#define RT305X_ESW_LED_BLINK 10
+#define RT305X_ESW_LED_ON 12
+
+#define RT305X_ESW_LINK_S 25
+#define RT305X_ESW_DUPLEX_S 9
+#define RT305X_ESW_SPD_S 0
+
+#define RT305X_ESW_PCR0_WT_NWAY_DATA_S 16
+#define RT305X_ESW_PCR0_WT_PHY_CMD BIT(13)
+#define RT305X_ESW_PCR0_CPU_PHY_REG_S 8
+
+#define RT305X_ESW_PCR1_WT_DONE BIT(0)
+
+#define RT305X_ESW_ATS_TIMEOUT (5 * HZ)
+#define RT305X_ESW_PHY_TIMEOUT (5 * HZ)
+
+#define RT305X_ESW_PVIDC_PVID_M 0xfff
+#define RT305X_ESW_PVIDC_PVID_S 12
+
+#define RT305X_ESW_VLANI_VID_M 0xfff
+#define RT305X_ESW_VLANI_VID_S 12
+
+#define RT305X_ESW_VMSC_MSC_M 0xff
+#define RT305X_ESW_VMSC_MSC_S 8
+
+#define RT305X_ESW_SOCPC_DISUN2CPU_S 0
+#define RT305X_ESW_SOCPC_DISMC2CPU_S 8
+#define RT305X_ESW_SOCPC_DISBC2CPU_S 16
+#define RT305X_ESW_SOCPC_CRC_PADDING BIT(25)
+
+#define RT305X_ESW_POC0_EN_BP_S 0
+#define RT305X_ESW_POC0_EN_FC_S 8
+#define RT305X_ESW_POC0_DIS_RMC2CPU_S 16
+#define RT305X_ESW_POC0_DIS_PORT_M 0x7f
+#define RT305X_ESW_POC0_DIS_PORT_S 23
+
+#define RT305X_ESW_POC2_UNTAG_EN_M 0xff
+#define RT305X_ESW_POC2_UNTAG_EN_S 0
+#define RT305X_ESW_POC2_ENAGING_S 8
+#define RT305X_ESW_POC2_DIS_UC_PAUSE_S 16
+
+#define RT305X_ESW_SGC2_DOUBLE_TAG_M 0x7f
+#define RT305X_ESW_SGC2_DOUBLE_TAG_S 0
+#define RT305X_ESW_SGC2_LAN_PMAP_M 0x3f
+#define RT305X_ESW_SGC2_LAN_PMAP_S 24
+
+#define RT305X_ESW_PFC1_EN_VLAN_M 0xff
+#define RT305X_ESW_PFC1_EN_VLAN_S 16
+#define RT305X_ESW_PFC1_EN_TOS_S 24
+
+#define RT305X_ESW_VLAN_NONE 0xfff
+
+#define RT305X_ESW_GSC_BC_STROM_MASK 0x3
+#define RT305X_ESW_GSC_BC_STROM_SHIFT 4
+
+#define RT305X_ESW_GSC_LED_FREQ_MASK 0x3
+#define RT305X_ESW_GSC_LED_FREQ_SHIFT 23
+
+#define RT305X_ESW_POA_LINK_MASK 0x1f
+#define RT305X_ESW_POA_LINK_SHIFT 25
+
+#define RT305X_ESW_PORT_ST_CHG BIT(26)
+#define RT305X_ESW_PORT0 0
+#define RT305X_ESW_PORT1 1
+#define RT305X_ESW_PORT2 2
+#define RT305X_ESW_PORT3 3
+#define RT305X_ESW_PORT4 4
+#define RT305X_ESW_PORT5 5
+#define RT305X_ESW_PORT6 6
+
+#define RT305X_ESW_PORTS_NONE 0
+
+#define RT305X_ESW_PMAP_LLLLLL 0x3f
+#define RT305X_ESW_PMAP_LLLLWL 0x2f
+#define RT305X_ESW_PMAP_WLLLLL 0x3e
+
+#define RT305X_ESW_PORTS_INTERNAL \
+ (BIT(RT305X_ESW_PORT0) | BIT(RT305X_ESW_PORT1) | \
+ BIT(RT305X_ESW_PORT2) | BIT(RT305X_ESW_PORT3) | \
+ BIT(RT305X_ESW_PORT4))
+
+#define RT305X_ESW_PORTS_NOCPU \
+ (RT305X_ESW_PORTS_INTERNAL | BIT(RT305X_ESW_PORT5))
+
+#define RT305X_ESW_PORTS_CPU BIT(RT305X_ESW_PORT6)
+
+#define RT305X_ESW_PORTS_ALL \
+ (RT305X_ESW_PORTS_NOCPU | RT305X_ESW_PORTS_CPU)
+
+#define RT305X_ESW_NUM_VLANS 16
+#define RT305X_ESW_NUM_VIDS 4096
+#define RT305X_ESW_NUM_PORTS 7
+#define RT305X_ESW_NUM_LANWAN 6
+#define RT305X_ESW_NUM_LEDS 5
+
+#define RT5350_ESW_REG_PXTPC(_x) (0x150 + (4 * _x))
+#define RT5350_EWS_REG_LED_POLARITY 0x168
+#define RT5350_RESET_EPHY BIT(24)
+
+enum {
+ /* Global attributes. */
+ RT305X_ESW_ATTR_ENABLE_VLAN,
+ RT305X_ESW_ATTR_ALT_VLAN_DISABLE,
+ RT305X_ESW_ATTR_BC_STATUS,
+ RT305X_ESW_ATTR_LED_FREQ,
+ /* Port attributes. */
+ RT305X_ESW_ATTR_PORT_DISABLE,
+ RT305X_ESW_ATTR_PORT_DOUBLETAG,
+ RT305X_ESW_ATTR_PORT_UNTAG,
+ RT305X_ESW_ATTR_PORT_LED,
+ RT305X_ESW_ATTR_PORT_LAN,
+ RT305X_ESW_ATTR_PORT_RECV_BAD,
+ RT305X_ESW_ATTR_PORT_RECV_GOOD,
+ RT5350_ESW_ATTR_PORT_TR_BAD,
+ RT5350_ESW_ATTR_PORT_TR_GOOD,
+};
+
+struct esw_port {
+ bool disable;
+ bool doubletag;
+ bool untag;
+ u8 led;
+ u16 pvid;
+};
+
+struct esw_vlan {
+ u8 ports;
+ u16 vid;
+};
+
+enum {
+ RT305X_ESW_VLAN_CONFIG_NONE = 0,
+ RT305X_ESW_VLAN_CONFIG_LLLLW,
+ RT305X_ESW_VLAN_CONFIG_WLLLL,
+};
+
+struct rt305x_esw {
+ struct device *dev;
+ void __iomem *base;
+ int irq;
+
+ /* Protects against concurrent register r/w operations. */
+ spinlock_t reg_rw_lock;
+
+ unsigned char port_map;
+ unsigned int reg_led_polarity;
+
+ bool global_vlan_enable;
+ bool alt_vlan_disable;
+ int bc_storm_protect;
+ int led_frequency;
+ struct esw_vlan vlans[RT305X_ESW_NUM_VLANS];
+ struct esw_port ports[RT305X_ESW_NUM_PORTS];
+
+};
+
+static inline void esw_w32(struct rt305x_esw *esw, u32 val, unsigned reg)
+{
+ __raw_writel(val, esw->base + reg);
+}
+
+static inline u32 esw_r32(struct rt305x_esw *esw, unsigned reg)
+{
+ return __raw_readl(esw->base + reg);
+}
+
+static inline void esw_rmw_raw(struct rt305x_esw *esw, unsigned reg,
+ unsigned long mask, unsigned long val)
+{
+ unsigned long t;
+
+ t = __raw_readl(esw->base + reg) & ~mask;
+ __raw_writel(t | val, esw->base + reg);
+}
+
+static void esw_rmw(struct rt305x_esw *esw, unsigned reg,
+ unsigned long mask, unsigned long val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&esw->reg_rw_lock, flags);
+ esw_rmw_raw(esw, reg, mask, val);
+ spin_unlock_irqrestore(&esw->reg_rw_lock, flags);
+}
+
+static u32 rt305x_mii_write(struct rt305x_esw *esw, u32 phy_addr,
+ u32 phy_register, u32 write_data)
+{
+ unsigned long t_start = jiffies;
+ int ret = 0;
+
+ while (1) {
+ if (!(esw_r32(esw, RT305X_ESW_REG_PCR1) &
+ RT305X_ESW_PCR1_WT_DONE))
+ break;
+ if (time_after(jiffies, t_start + RT305X_ESW_PHY_TIMEOUT)) {
+ ret = 1;
+ goto out;
+ }
+ }
+
+ write_data &= 0xffff;
+ esw_w32(esw, (write_data << RT305X_ESW_PCR0_WT_NWAY_DATA_S) |
+ (phy_register << RT305X_ESW_PCR0_CPU_PHY_REG_S) |
+ (phy_addr) | RT305X_ESW_PCR0_WT_PHY_CMD,
+ RT305X_ESW_REG_PCR0);
+
+ t_start = jiffies;
+ while (1) {
+ if (esw_r32(esw, RT305X_ESW_REG_PCR1) &
+ RT305X_ESW_PCR1_WT_DONE)
+ break;
+
+ if (time_after(jiffies, t_start + RT305X_ESW_PHY_TIMEOUT)) {
+ ret = 1;
+ break;
+ }
+ }
+out:
+ if (ret)
+ dev_err(esw->dev, "ramips_eth: MDIO timeout\n");
+ return ret;
+}
+
+static unsigned esw_get_port_disable(struct rt305x_esw *esw)
+{
+ unsigned reg;
+
+ reg = esw_r32(esw, RT305X_ESW_REG_POC0);
+ return (reg >> RT305X_ESW_POC0_DIS_PORT_S) &
+ RT305X_ESW_POC0_DIS_PORT_M;
+}
+
+static void esw_hw_init(struct rt305x_esw *esw)
+{
+ int i;
+ u8 port_disable = 0;
+ u8 port_map = RT305X_ESW_PMAP_LLLLLL;
+
+ /* vodoo from original driver */
+ esw_w32(esw, 0xC8A07850, RT305X_ESW_REG_FCT0);
+ esw_w32(esw, 0x00000000, RT305X_ESW_REG_SGC2);
+ /* Port priority 1 for all ports, vlan enabled. */
+ esw_w32(esw, 0x00005555 |
+ (RT305X_ESW_PORTS_ALL << RT305X_ESW_PFC1_EN_VLAN_S),
+ RT305X_ESW_REG_PFC1);
+
+ /* Enable Back Pressure, and Flow Control */
+ esw_w32(esw, ((RT305X_ESW_PORTS_ALL << RT305X_ESW_POC0_EN_BP_S) |
+ (RT305X_ESW_PORTS_ALL << RT305X_ESW_POC0_EN_FC_S)),
+ RT305X_ESW_REG_POC0);
+
+ /* Enable Aging, and VLAN TAG removal */
+ esw_w32(esw, ((RT305X_ESW_PORTS_ALL << RT305X_ESW_POC2_ENAGING_S) |
+ (RT305X_ESW_PORTS_NOCPU << RT305X_ESW_POC2_UNTAG_EN_S)),
+ RT305X_ESW_REG_POC2);
+
+ esw_w32(esw, 0x00d6500c, RT305X_ESW_REG_FCT2);
+
+ /* 300s aging timer, max packet len 1536, broadcast storm prevention
+ * disabled, disable collision abort, mac xor48 hash, 10 packet back
+ * pressure jam, GMII disable was_transmit, back pressure disabled,
+ * 30ms led flash, unmatched IGMP as broadcast, rmc tb fault to all
+ * ports.
+ */
+ esw_w32(esw, 0x0008a301, RT305X_ESW_REG_SGC);
+
+ /* Setup SoC Port control register */
+ esw_w32(esw,
+ (RT305X_ESW_SOCPC_CRC_PADDING |
+ (RT305X_ESW_PORTS_CPU << RT305X_ESW_SOCPC_DISUN2CPU_S) |
+ (RT305X_ESW_PORTS_CPU << RT305X_ESW_SOCPC_DISMC2CPU_S) |
+ (RT305X_ESW_PORTS_CPU << RT305X_ESW_SOCPC_DISBC2CPU_S)),
+ RT305X_ESW_REG_SOCPC);
+
+ /* ext phy base addr 31, enable port 5 polling, rx/tx clock skew 1,
+ * turbo mii off, rgmi 3.3v off
+ * port5: disabled
+ * port6: enabled, gige, full-duplex, rx/tx-flow-control
+ */
+ esw_w32(esw, 0x3f502b28, RT305X_ESW_REG_FPA2);
+ esw_w32(esw, 0x00000000, RT305X_ESW_REG_FPA);
+
+ /* Force Link/Activity on ports */
+ esw_w32(esw, 0x00000005, RT305X_ESW_REG_P0LED);
+ esw_w32(esw, 0x00000005, RT305X_ESW_REG_P1LED);
+ esw_w32(esw, 0x00000005, RT305X_ESW_REG_P2LED);
+ esw_w32(esw, 0x00000005, RT305X_ESW_REG_P3LED);
+ esw_w32(esw, 0x00000005, RT305X_ESW_REG_P4LED);
+
+ /* Copy disabled port configuration from bootloader setup */
+ port_disable = esw_get_port_disable(esw);
+ for (i = 0; i < 6; i++)
+ esw->ports[i].disable = (port_disable & (1 << i)) != 0;
+
+ if (ralink_soc == RT305X_SOC_RT3352) {
+ /* reset EPHY */
+ fe_reset(RT5350_RESET_EPHY);
+
+ rt305x_mii_write(esw, 0, 31, 0x8000);
+ for (i = 0; i < 5; i++) {
+ if (esw->ports[i].disable) {
+ rt305x_mii_write(esw, i, MII_BMCR, BMCR_PDOWN);
+ } else {
+ rt305x_mii_write(esw, i, MII_BMCR,
+ BMCR_FULLDPLX |
+ BMCR_ANENABLE |
+ BMCR_SPEED100);
+ }
+ /* TX10 waveform coefficient LSB=0 disable PHY */
+ rt305x_mii_write(esw, i, 26, 0x1601);
+ /* TX100/TX10 AD/DA current bias */
+ rt305x_mii_write(esw, i, 29, 0x7016);
+ /* TX100 slew rate control */
+ rt305x_mii_write(esw, i, 30, 0x0038);
+ }
+
+ /* select global register */
+ rt305x_mii_write(esw, 0, 31, 0x0);
+ /* enlarge agcsel threshold 3 and threshold 2 */
+ rt305x_mii_write(esw, 0, 1, 0x4a40);
+ /* enlarge agcsel threshold 5 and threshold 4 */
+ rt305x_mii_write(esw, 0, 2, 0x6254);
+ /* enlarge agcsel threshold */
+ rt305x_mii_write(esw, 0, 3, 0xa17f);
+ rt305x_mii_write(esw, 0, 12, 0x7eaa);
+ /* longer TP_IDL tail length */
+ rt305x_mii_write(esw, 0, 14, 0x65);
+ /* increased squelch pulse count threshold. */
+ rt305x_mii_write(esw, 0, 16, 0x0684);
+ /* set TX10 signal amplitude threshold to minimum */
+ rt305x_mii_write(esw, 0, 17, 0x0fe0);
+ /* set squelch amplitude to higher threshold */
+ rt305x_mii_write(esw, 0, 18, 0x40ba);
+ /* tune TP_IDL tail and head waveform, enable power
+ * down slew rate control
+ */
+ rt305x_mii_write(esw, 0, 22, 0x253f);
+ /* set PLL/Receive bias current are calibrated */
+ rt305x_mii_write(esw, 0, 27, 0x2fda);
+ /* change PLL/Receive bias current to internal(RT3350) */
+ rt305x_mii_write(esw, 0, 28, 0xc410);
+ /* change PLL bias current to internal(RT3052_MP3) */
+ rt305x_mii_write(esw, 0, 29, 0x598b);
+ /* select local register */
+ rt305x_mii_write(esw, 0, 31, 0x8000);
+ } else if (ralink_soc == RT305X_SOC_RT5350) {
+ /* reset EPHY */
+ fe_reset(RT5350_RESET_EPHY);
+
+ /* set the led polarity */
+ esw_w32(esw, esw->reg_led_polarity & 0x1F,
+ RT5350_EWS_REG_LED_POLARITY);
+
+ /* local registers */
+ rt305x_mii_write(esw, 0, 31, 0x8000);
+ for (i = 0; i < 5; i++) {
+ if (esw->ports[i].disable) {
+ rt305x_mii_write(esw, i, MII_BMCR, BMCR_PDOWN);
+ } else {
+ rt305x_mii_write(esw, i, MII_BMCR,
+ BMCR_FULLDPLX |
+ BMCR_ANENABLE |
+ BMCR_SPEED100);
+ }
+ /* TX10 waveform coefficient LSB=0 disable PHY */
+ rt305x_mii_write(esw, i, 26, 0x1601);
+ /* TX100/TX10 AD/DA current bias */
+ rt305x_mii_write(esw, i, 29, 0x7015);
+ /* TX100 slew rate control */
+ rt305x_mii_write(esw, i, 30, 0x0038);
+ }
+
+ /* global registers */
+ rt305x_mii_write(esw, 0, 31, 0x0);
+ /* enlarge agcsel threshold 3 and threshold 2 */
+ rt305x_mii_write(esw, 0, 1, 0x4a40);
+ /* enlarge agcsel threshold 5 and threshold 4 */
+ rt305x_mii_write(esw, 0, 2, 0x6254);
+ /* enlarge agcsel threshold 6 */
+ rt305x_mii_write(esw, 0, 3, 0xa17f);
+ rt305x_mii_write(esw, 0, 12, 0x7eaa);
+ /* longer TP_IDL tail length */
+ rt305x_mii_write(esw, 0, 14, 0x65);
+ /* increased squelch pulse count threshold. */
+ rt305x_mii_write(esw, 0, 16, 0x0684);
+ /* set TX10 signal amplitude threshold to minimum */
+ rt305x_mii_write(esw, 0, 17, 0x0fe0);
+ /* set squelch amplitude to higher threshold */
+ rt305x_mii_write(esw, 0, 18, 0x40ba);
+ /* tune TP_IDL tail and head waveform, enable power
+ * down slew rate control
+ */
+ rt305x_mii_write(esw, 0, 22, 0x253f);
+ /* set PLL/Receive bias current are calibrated */
+ rt305x_mii_write(esw, 0, 27, 0x2fda);
+ /* change PLL/Receive bias current to internal(RT3350) */
+ rt305x_mii_write(esw, 0, 28, 0xc410);
+ /* change PLL bias current to internal(RT3052_MP3) */
+ rt305x_mii_write(esw, 0, 29, 0x598b);
+ /* select local register */
+ rt305x_mii_write(esw, 0, 31, 0x8000);
+ } else if (ralink_soc == MT762X_SOC_MT7628AN) {
+ int i;
+
+ /* reset EPHY */
+ fe_reset(RT5350_RESET_EPHY);
+
+ rt305x_mii_write(esw, 0, 31, 0x2000); /* change G2 page */
+ rt305x_mii_write(esw, 0, 26, 0x0020);
+
+ for (i = 0; i < 5; i++) {
+ rt305x_mii_write(esw, i, 31, 0x8000);
+ rt305x_mii_write(esw, i, 0, 0x3100);
+ rt305x_mii_write(esw, i, 30, 0xa000);
+ rt305x_mii_write(esw, i, 31, 0xa000);
+ rt305x_mii_write(esw, i, 16, 0x0606);
+ rt305x_mii_write(esw, i, 23, 0x0f0e);
+ rt305x_mii_write(esw, i, 24, 0x1610);
+ rt305x_mii_write(esw, i, 30, 0x1f15);
+ rt305x_mii_write(esw, i, 28, 0x6111);
+ rt305x_mii_write(esw, i, 31, 0x2000);
+ rt305x_mii_write(esw, i, 26, 0x0000);
+ }
+
+ /* 100Base AOI setting */
+ rt305x_mii_write(esw, 0, 31, 0x5000);
+ rt305x_mii_write(esw, 0, 19, 0x004a);
+ rt305x_mii_write(esw, 0, 20, 0x015a);
+ rt305x_mii_write(esw, 0, 21, 0x00ee);
+ rt305x_mii_write(esw, 0, 22, 0x0033);
+ rt305x_mii_write(esw, 0, 23, 0x020a);
+ rt305x_mii_write(esw, 0, 24, 0x0000);
+ rt305x_mii_write(esw, 0, 25, 0x024a);
+ rt305x_mii_write(esw, 0, 26, 0x035a);
+ rt305x_mii_write(esw, 0, 27, 0x02ee);
+ rt305x_mii_write(esw, 0, 28, 0x0233);
+ rt305x_mii_write(esw, 0, 29, 0x000a);
+ rt305x_mii_write(esw, 0, 30, 0x0000);
+ } else {
+ rt305x_mii_write(esw, 0, 31, 0x8000);
+ for (i = 0; i < 5; i++) {
+ if (esw->ports[i].disable) {
+ rt305x_mii_write(esw, i, MII_BMCR, BMCR_PDOWN);
+ } else {
+ rt305x_mii_write(esw, i, MII_BMCR,
+ BMCR_FULLDPLX |
+ BMCR_ANENABLE |
+ BMCR_SPEED100);
+ }
+ /* TX10 waveform coefficient */
+ rt305x_mii_write(esw, i, 26, 0x1601);
+ /* TX100/TX10 AD/DA current bias */
+ rt305x_mii_write(esw, i, 29, 0x7058);
+ /* TX100 slew rate control */
+ rt305x_mii_write(esw, i, 30, 0x0018);
+ }
+
+ /* PHY IOT */
+ /* select global register */
+ rt305x_mii_write(esw, 0, 31, 0x0);
+ /* tune TP_IDL tail and head waveform */
+ rt305x_mii_write(esw, 0, 22, 0x052f);
+ /* set TX10 signal amplitude threshold to minimum */
+ rt305x_mii_write(esw, 0, 17, 0x0fe0);
+ /* set squelch amplitude to higher threshold */
+ rt305x_mii_write(esw, 0, 18, 0x40ba);
+ /* longer TP_IDL tail length */
+ rt305x_mii_write(esw, 0, 14, 0x65);
+ /* select local register */
+ rt305x_mii_write(esw, 0, 31, 0x8000);
+ }
+
+ if (esw->port_map)
+ port_map = esw->port_map;
+ else
+ port_map = RT305X_ESW_PMAP_LLLLLL;
+
+ /* Unused HW feature, but still nice to be consistent here...
+ * This is also exported to userspace ('lan' attribute) so it's
+ * conveniently usable to decide which ports go into the wan vlan by
+ * default.
+ */
+ esw_rmw(esw, RT305X_ESW_REG_SGC2,
+ RT305X_ESW_SGC2_LAN_PMAP_M << RT305X_ESW_SGC2_LAN_PMAP_S,
+ port_map << RT305X_ESW_SGC2_LAN_PMAP_S);
+
+ /* make the switch leds blink */
+ for (i = 0; i < RT305X_ESW_NUM_LEDS; i++)
+ esw->ports[i].led = 0x05;
+
+ /* Only unmask the port change interrupt */
+ esw_w32(esw, ~RT305X_ESW_PORT_ST_CHG, RT305X_ESW_REG_IMR);
+}
+
+static irqreturn_t esw_interrupt(int irq, void *_esw)
+{
+ struct rt305x_esw *esw = (struct rt305x_esw *)_esw;
+ u32 status;
+
+ status = esw_r32(esw, RT305X_ESW_REG_ISR);
+ if (status & RT305X_ESW_PORT_ST_CHG) {
+ u32 link = esw_r32(esw, RT305X_ESW_REG_POA);
+
+ link >>= RT305X_ESW_POA_LINK_SHIFT;
+ link &= RT305X_ESW_POA_LINK_MASK;
+ dev_info(esw->dev, "link changed 0x%02X\n", link);
+ }
+ esw_w32(esw, status, RT305X_ESW_REG_ISR);
+
+ return IRQ_HANDLED;
+}
+
+static int esw_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ const __be32 *port_map, *reg_init;
+ struct rt305x_esw *esw;
+ struct resource *res, *irq;
+ int ret;
+
+ esw = devm_kzalloc(&pdev->dev, sizeof(*esw), GFP_KERNEL);
+ if (!esw)
+ return -ENOMEM;
+
+ esw->dev = &pdev->dev;
+ esw->irq = irq->start;
+ esw->base = devm_ioremap_resource(&pdev->dev, res);
+ if (!esw->base)
+ return -EADDRNOTAVAIL;
+
+ port_map = of_get_property(np, "ralink,portmap", NULL);
+ if (port_map)
+ esw->port_map = be32_to_cpu(*port_map);
+
+ reg_init = of_get_property(np, "ralink,led_polarity", NULL);
+ if (reg_init)
+ esw->reg_led_polarity = be32_to_cpu(*reg_init);
+
+ platform_set_drvdata(pdev, esw);
+
+ spin_lock_init(&esw->reg_rw_lock);
+
+ esw_hw_init(esw);
+
+ ret = devm_request_irq(&pdev->dev, esw->irq, esw_interrupt, 0, "esw",
+ esw);
+
+ if (!ret) {
+ esw_w32(esw, RT305X_ESW_PORT_ST_CHG, RT305X_ESW_REG_ISR);
+ esw_w32(esw, ~RT305X_ESW_PORT_ST_CHG, RT305X_ESW_REG_IMR);
+ }
+
+ return ret;
+}
+
+static int esw_remove(struct platform_device *pdev)
+{
+ struct rt305x_esw *esw = platform_get_drvdata(pdev);
+
+ if (esw) {
+ esw_w32(esw, ~0, RT305X_ESW_REG_IMR);
+ platform_set_drvdata(pdev, NULL);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id ralink_esw_match[] = {
+ { .compatible = "ralink,rt3050-esw" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ralink_esw_match);
+
+static struct platform_driver esw_driver = {
+ .probe = esw_probe,
+ .remove = esw_remove,
+ .driver = {
+ .name = "rt305x-esw",
+ .owner = THIS_MODULE,
+ .of_match_table = ralink_esw_match,
+ },
+};
+
+int __init rtesw_init(void)
+{
+ return platform_driver_register(&esw_driver);
+}
+
+void rtesw_exit(void)
+{
+ platform_driver_unregister(&esw_driver);
+}
diff --git a/drivers/net/ethernet/ralink/esw_rt3050.h b/drivers/net/ethernet/ralink/esw_rt3050.h
new file mode 100644
index 0000000..3af0b8d
--- /dev/null
+++ b/drivers/net/ethernet/ralink/esw_rt3050.h
@@ -0,0 +1,29 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#ifndef _RALINK_ESW_RT3052_H__
+#define _RALINK_ESW_RT3052_H__
+
+#ifdef CONFIG_NET_RALINK_ESW_RT3052
+
+int __init rtesw_init(void);
+void rtesw_exit(void);
+
+#else
+
+static inline int __init rtesw_init(void) { return 0; }
+static inline void rtesw_exit(void) { }
+
+#endif
+#endif
diff --git a/drivers/net/ethernet/ralink/soc_rt3050.c b/drivers/net/ethernet/ralink/soc_rt3050.c
new file mode 100644
index 0000000..25f35b0
--- /dev/null
+++ b/drivers/net/ethernet/ralink/soc_rt3050.c
@@ -0,0 +1,154 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "ralink_soc_eth.h"
+#include "mdio_rt2880.h"
+
+#define RT305X_RESET_FE BIT(21)
+#define RT305X_RESET_ESW BIT(23)
+
+static const u16 rt5350_reg_table[FE_REG_COUNT] = {
+ [FE_REG_PDMA_GLO_CFG] = RT5350_PDMA_GLO_CFG,
+ [FE_REG_PDMA_RST_CFG] = RT5350_PDMA_RST_CFG,
+ [FE_REG_DLY_INT_CFG] = RT5350_DLY_INT_CFG,
+ [FE_REG_TX_BASE_PTR0] = RT5350_TX_BASE_PTR0,
+ [FE_REG_TX_MAX_CNT0] = RT5350_TX_MAX_CNT0,
+ [FE_REG_TX_CTX_IDX0] = RT5350_TX_CTX_IDX0,
+ [FE_REG_TX_DTX_IDX0] = RT5350_TX_DTX_IDX0,
+ [FE_REG_RX_BASE_PTR0] = RT5350_RX_BASE_PTR0,
+ [FE_REG_RX_MAX_CNT0] = RT5350_RX_MAX_CNT0,
+ [FE_REG_RX_CALC_IDX0] = RT5350_RX_CALC_IDX0,
+ [FE_REG_RX_DRX_IDX0] = RT5350_RX_DRX_IDX0,
+ [FE_REG_FE_INT_ENABLE] = RT5350_FE_INT_ENABLE,
+ [FE_REG_FE_INT_STATUS] = RT5350_FE_INT_STATUS,
+ [FE_REG_FE_RST_GL] = 0,
+ [FE_REG_FE_DMA_VID_BASE] = 0,
+};
+
+static void rt305x_init_data(struct fe_soc_data *data,
+ struct net_device *netdev)
+{
+ struct fe_priv *priv = netdev_priv(netdev);
+
+ priv->flags = FE_FLAG_PADDING_64B | FE_FLAG_PADDING_BUG;
+ netdev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM |
+ NETIF_F_RXCSUM | NETIF_F_HW_VLAN_CTAG_TX;
+}
+
+static int rt3050_fwd_config(struct fe_priv *priv)
+{
+ int ret;
+
+ if (ralink_soc != RT305X_SOC_RT3052) {
+ ret = fe_set_clock_cycle(priv);
+ if (ret)
+ return ret;
+ }
+
+ fe_fwd_config(priv);
+ if (ralink_soc != RT305X_SOC_RT3352)
+ fe_w32(FE_PSE_FQFC_CFG_INIT, FE_PSE_FQ_CFG);
+ fe_csum_config(priv);
+
+ return 0;
+}
+
+static void rt305x_fe_reset(void)
+{
+ fe_reset(RT305X_RESET_FE);
+}
+
+static void rt5350_init_data(struct fe_soc_data *data,
+ struct net_device *netdev)
+{
+ netdev->hw_features = NETIF_F_SG | NETIF_F_RXCSUM;
+}
+
+static void rt5350_set_mac(struct fe_priv *priv, unsigned char *mac)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->page_lock, flags);
+ fe_w32((mac[0] << 8) | mac[1], RT5350_SDM_MAC_ADRH);
+ fe_w32((mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5],
+ RT5350_SDM_MAC_ADRL);
+ spin_unlock_irqrestore(&priv->page_lock, flags);
+}
+
+static void rt5350_rxcsum_config(bool enable)
+{
+ if (enable)
+ fe_w32(fe_r32(RT5350_SDM_CFG) | (RT5350_SDM_ICS_EN |
+ RT5350_SDM_TCS_EN | RT5350_SDM_UCS_EN),
+ RT5350_SDM_CFG);
+ else
+ fe_w32(fe_r32(RT5350_SDM_CFG) & ~(RT5350_SDM_ICS_EN |
+ RT5350_SDM_TCS_EN | RT5350_SDM_UCS_EN),
+ RT5350_SDM_CFG);
+}
+
+static int rt5350_fwd_config(struct fe_priv *priv)
+{
+ struct net_device *dev = priv_netdev(priv);
+
+ rt5350_rxcsum_config((dev->features & NETIF_F_RXCSUM));
+
+ return 0;
+}
+
+static void rt5350_tx_dma(struct fe_tx_dma *txd)
+{
+ txd->txd4 = 0;
+}
+
+static void rt5350_fe_reset(void)
+{
+ fe_reset(RT305X_RESET_FE | RT305X_RESET_ESW);
+}
+
+static struct fe_soc_data rt3050_data = {
+ .init_data = rt305x_init_data,
+ .reset_fe = rt305x_fe_reset,
+ .fwd_config = rt3050_fwd_config,
+ .pdma_glo_cfg = FE_PDMA_SIZE_8DWORDS,
+ .checksum_bit = RX_DMA_L4VALID,
+ .rx_int = FE_RX_DONE_INT,
+ .tx_int = FE_TX_DONE_INT,
+ .status_int = FE_CNT_GDM_AF,
+};
+
+static struct fe_soc_data rt5350_data = {
+ .init_data = rt5350_init_data,
+ .reg_table = rt5350_reg_table,
+ .reset_fe = rt5350_fe_reset,
+ .set_mac = rt5350_set_mac,
+ .fwd_config = rt5350_fwd_config,
+ .tx_dma = rt5350_tx_dma,
+ .pdma_glo_cfg = FE_PDMA_SIZE_8DWORDS,
+ .checksum_bit = RX_DMA_L4VALID,
+ .rx_int = RT5350_RX_DONE_INT,
+ .tx_int = RT5350_TX_DONE_INT,
+};
+
+const struct of_device_id of_fe_match[] = {
+ { .compatible = "ralink,rt3050-eth", .data = &rt3050_data },
+ { .compatible = "ralink,rt5350-eth", .data = &rt5350_data },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, of_fe_match);
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 6/8] net-next: ralink: add support for rt3883
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
` (3 preceding siblings ...)
2015-11-22 8:40 ` [RFC 5/8] net-next: ralink: add support for rt3050 family John Crispin
@ 2015-11-22 8:40 ` John Crispin
2015-11-22 8:40 ` [RFC 7/8] net-next: ralink: add support for mt7620 family John Crispin
2015-11-22 8:40 ` [RFC 8/8] net-next: ralink: add Kconfig and Makefile John Crispin
6 siblings, 0 replies; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
Add support for rt3883 and its smaller version rt3662. They both have a single
gBit port that will normally be attached to an external phy of switch.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
---
drivers/net/ethernet/ralink/soc_rt3883.c | 75 ++++++++++++++++++++++++++++++
1 file changed, 75 insertions(+)
create mode 100644 drivers/net/ethernet/ralink/soc_rt3883.c
diff --git a/drivers/net/ethernet/ralink/soc_rt3883.c b/drivers/net/ethernet/ralink/soc_rt3883.c
new file mode 100644
index 0000000..f7b6769
--- /dev/null
+++ b/drivers/net/ethernet/ralink/soc_rt3883.c
@@ -0,0 +1,75 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "ralink_soc_eth.h"
+#include "mdio_rt2880.h"
+
+#define RT3883_RSTCTRL_FE BIT(21)
+
+static void rt3883_fe_reset(void)
+{
+ fe_reset(RT3883_RSTCTRL_FE);
+}
+
+static int rt3883_fwd_config(struct fe_priv *priv)
+{
+ int ret;
+
+ ret = fe_set_clock_cycle(priv);
+ if (ret)
+ return ret;
+
+ fe_fwd_config(priv);
+ fe_w32(FE_PSE_FQFC_CFG_256Q, FE_PSE_FQ_CFG);
+ fe_csum_config(priv);
+
+ return ret;
+}
+
+static void rt3883_init_data(struct fe_soc_data *data,
+ struct net_device *netdev)
+{
+ struct fe_priv *priv = netdev_priv(netdev);
+
+ priv->flags = FE_FLAG_PADDING_64B | FE_FLAG_PADDING_BUG |
+ FE_FLAG_JUMBO_FRAME;
+ netdev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM |
+ NETIF_F_RXCSUM | NETIF_F_HW_VLAN_CTAG_TX;
+}
+
+static struct fe_soc_data rt3883_data = {
+ .init_data = rt3883_init_data,
+ .reset_fe = rt3883_fe_reset,
+ .fwd_config = rt3883_fwd_config,
+ .pdma_glo_cfg = FE_PDMA_SIZE_8DWORDS,
+ .rx_int = FE_RX_DONE_INT,
+ .tx_int = FE_TX_DONE_INT,
+ .status_int = FE_CNT_GDM_AF,
+ .checksum_bit = RX_DMA_L4VALID,
+ .mdio_read = rt2880_mdio_read,
+ .mdio_write = rt2880_mdio_write,
+ .mdio_adjust_link = rt2880_mdio_link_adjust,
+ .port_init = rt2880_port_init,
+};
+
+const struct of_device_id of_fe_match[] = {
+ { .compatible = "ralink,rt3883-eth", .data = &rt3883_data },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, of_fe_match);
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 7/8] net-next: ralink: add support for mt7620 family
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
` (4 preceding siblings ...)
2015-11-22 8:40 ` [RFC 6/8] net-next: ralink: add support for rt3883 John Crispin
@ 2015-11-22 8:40 ` John Crispin
2015-11-22 8:40 ` [RFC 8/8] net-next: ralink: add Kconfig and Makefile John Crispin
6 siblings, 0 replies; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
Add support for SoCs from the mt7620 family. This include mt7620 and mt7621.
These all have one dedicated external gbit port and a builtin 5 port 100mbit
switch. Additionally one of the 5 switch ports can be changed to become an
additional gbit port that we can attach a phy to. This patch includes
rudimentary code to power up the switch. There are a lot of magic values
that get written to the switch and the internal phys. These values come
straight from the SDK driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
---
drivers/net/ethernet/ralink/gsw_mt7620.c | 784 ++++++++++++++++++++++++++++++
drivers/net/ethernet/ralink/gsw_mt7620.h | 26 +
drivers/net/ethernet/ralink/soc_mt7620.c | 273 +++++++++++
3 files changed, 1083 insertions(+)
create mode 100644 drivers/net/ethernet/ralink/gsw_mt7620.c
create mode 100644 drivers/net/ethernet/ralink/gsw_mt7620.h
create mode 100644 drivers/net/ethernet/ralink/soc_mt7620.c
diff --git a/drivers/net/ethernet/ralink/gsw_mt7620.c b/drivers/net/ethernet/ralink/gsw_mt7620.c
new file mode 100644
index 0000000..24bc312
--- /dev/null
+++ b/drivers/net/ethernet/ralink/gsw_mt7620.c
@@ -0,0 +1,784 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/skbuff.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/ioport.h>
+#include <linux/mii.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "ralink_soc_eth.h"
+
+#include <ralink_regs.h>
+#include <asm/mach-ralink/mt7620.h>
+
+#include "ralink_soc_eth.h"
+#include "gsw_mt7620.h"
+#include "mdio.h"
+
+#define GSW_REG_PHY_TIMEOUT (5 * HZ)
+
+#ifdef CONFIG_SOC_MT7621
+#define MT7620A_GSW_REG_PIAC 0x0004
+#else
+#define MT7620A_GSW_REG_PIAC 0x7004
+#endif
+
+#define GSW_NUM_VLANS 16
+#define GSW_NUM_VIDS 4096
+#define GSW_NUM_PORTS 7
+#define GSW_PORT6 6
+
+#define GSW_MDIO_ACCESS BIT(31)
+#define GSW_MDIO_READ BIT(19)
+#define GSW_MDIO_WRITE BIT(18)
+#define GSW_MDIO_START BIT(16)
+#define GSW_MDIO_ADDR_SHIFT 20
+#define GSW_MDIO_REG_SHIFT 25
+
+#define GSW_REG_PORT_PMCR(x) (0x3000 + (x * 0x100))
+#define GSW_REG_PORT_STATUS(x) (0x3008 + (x * 0x100))
+#define GSW_REG_SMACCR0 0x3fE4
+#define GSW_REG_SMACCR1 0x3fE8
+#define GSW_REG_CKGCR 0x3ff0
+
+#define GSW_REG_IMR 0x7008
+#define GSW_REG_ISR 0x700c
+#define GSW_REG_GPC1 0x7014
+
+#define SYSC_REG_CHIP_REV_ID 0x0c
+#define SYSC_REG_CFG1 0x14
+#define RST_CTRL_MCM BIT(2)
+#define SYSC_PAD_RGMII2_MDIO 0x58
+#define SYSC_GPIO_MODE 0x60
+
+#define PORT_IRQ_ST_CHG 0x7f
+
+#ifdef CONFIG_SOC_MT7621
+#define ESW_PHY_POLLING 0x0000
+#else
+#define ESW_PHY_POLLING 0x7000
+#endif
+
+#define PMCR_IPG BIT(18)
+#define PMCR_MAC_MODE BIT(16)
+#define PMCR_FORCE BIT(15)
+#define PMCR_TX_EN BIT(14)
+#define PMCR_RX_EN BIT(13)
+#define PMCR_BACKOFF BIT(9)
+#define PMCR_BACKPRES BIT(8)
+#define PMCR_RX_FC BIT(5)
+#define PMCR_TX_FC BIT(4)
+#define PMCR_SPEED(_x) (_x << 2)
+#define PMCR_DUPLEX BIT(1)
+#define PMCR_LINK BIT(0)
+
+#define PHY_AN_EN BIT(31)
+#define PHY_PRE_EN BIT(30)
+#define PMY_MDC_CONF(_x) ((_x & 0x3f) << 24)
+
+enum {
+ /* Global attributes. */
+ GSW_ATTR_ENABLE_VLAN,
+ /* Port attributes. */
+ GSW_ATTR_PORT_UNTAG,
+};
+
+enum {
+ PORT4_EPHY = 0,
+ PORT4_EXT,
+};
+
+struct mt7620_gsw {
+ struct device *dev;
+ void __iomem *base;
+ int irq;
+ int port4;
+ unsigned long int autopoll;
+};
+
+static inline void gsw_w32(struct mt7620_gsw *gsw, u32 val, unsigned reg)
+{
+ iowrite32(val, gsw->base + reg);
+}
+
+static inline u32 gsw_r32(struct mt7620_gsw *gsw, unsigned reg)
+{
+ return ioread32(gsw->base + reg);
+}
+
+static int mt7620_mii_busy_wait(struct mt7620_gsw *gsw)
+{
+ unsigned long t_start = jiffies;
+
+ while (1) {
+ if (!(gsw_r32(gsw, MT7620A_GSW_REG_PIAC) & GSW_MDIO_ACCESS))
+ return 0;
+ if (time_after(jiffies, t_start + GSW_REG_PHY_TIMEOUT))
+ break;
+ }
+
+ dev_err(gsw->dev, "mdio: MDIO timeout\n");
+ return -1;
+}
+
+static u32 _mt7620_mii_write(struct mt7620_gsw *gsw, u32 phy_addr,
+ u32 phy_register, u32 write_data)
+{
+ if (mt7620_mii_busy_wait(gsw))
+ return -1;
+
+ write_data &= 0xffff;
+
+ gsw_w32(gsw, GSW_MDIO_ACCESS | GSW_MDIO_START | GSW_MDIO_WRITE |
+ (phy_register << GSW_MDIO_REG_SHIFT) |
+ (phy_addr << GSW_MDIO_ADDR_SHIFT) | write_data,
+ MT7620A_GSW_REG_PIAC);
+
+ if (mt7620_mii_busy_wait(gsw))
+ return -1;
+
+ return 0;
+}
+
+static u32 _mt7620_mii_read(struct mt7620_gsw *gsw, int phy_addr, int phy_reg)
+{
+ u32 d;
+
+ if (mt7620_mii_busy_wait(gsw))
+ return 0xffff;
+
+ gsw_w32(gsw, GSW_MDIO_ACCESS | GSW_MDIO_START | GSW_MDIO_READ |
+ (phy_reg << GSW_MDIO_REG_SHIFT) |
+ (phy_addr << GSW_MDIO_ADDR_SHIFT),
+ MT7620A_GSW_REG_PIAC);
+
+ if (mt7620_mii_busy_wait(gsw))
+ return 0xffff;
+
+ d = gsw_r32(gsw, MT7620A_GSW_REG_PIAC) & 0xffff;
+
+ return d;
+}
+
+int mt7620_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, u16 val)
+{
+ struct fe_priv *priv = bus->priv;
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+
+ return _mt7620_mii_write(gsw, phy_addr, phy_reg, val);
+}
+
+int mt7620_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg)
+{
+ struct fe_priv *priv = bus->priv;
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+
+ return _mt7620_mii_read(gsw, phy_addr, phy_reg);
+}
+
+static void mt7530_mdio_w32(struct mt7620_gsw *gsw, u32 reg, u32 val)
+{
+ _mt7620_mii_write(gsw, 0x1f, 0x1f, (reg >> 6) & 0x3ff);
+ _mt7620_mii_write(gsw, 0x1f, (reg >> 2) & 0xf, val & 0xffff);
+ _mt7620_mii_write(gsw, 0x1f, 0x10, val >> 16);
+}
+
+static u32 mt7530_mdio_r32(struct mt7620_gsw *gsw, u32 reg)
+{
+ u16 high, low;
+
+ _mt7620_mii_write(gsw, 0x1f, 0x1f, (reg >> 6) & 0x3ff);
+ low = _mt7620_mii_read(gsw, 0x1f, (reg >> 2) & 0xf);
+ high = _mt7620_mii_read(gsw, 0x1f, 0x10);
+
+ return (high << 16) | (low & 0xffff);
+}
+
+static unsigned char *fe_speed_str(int speed)
+{
+ switch (speed) {
+ case 2:
+ case SPEED_1000:
+ return "1000";
+ case 1:
+ case SPEED_100:
+ return "100";
+ case 0:
+ case SPEED_10:
+ return "10";
+ }
+
+ return "? ";
+}
+
+int mt7620a_has_carrier(struct fe_priv *priv)
+{
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+ int i;
+
+ for (i = 0; i < GSW_PORT6; i++)
+ if (gsw_r32(gsw, GSW_REG_PORT_STATUS(i)) & 0x1)
+ return 1;
+ return 0;
+}
+
+static void mt7620_handle_carrier(struct fe_priv *priv)
+{
+ if (!priv->phy)
+ return;
+
+ if (mt7620a_has_carrier(priv))
+ netif_carrier_on(priv->netdev);
+ else
+ netif_carrier_off(priv->netdev);
+}
+
+static void mt7620_print_link_state(struct fe_priv *priv, int port, int link,
+ int speed, int duplex)
+{
+ if (link)
+ netdev_info(priv->netdev, "port %d link up (%sMbps/%s duplex)\n",
+ port, fe_speed_str(speed),
+ (duplex) ? "Full" : "Half");
+ else
+ netdev_info(priv->netdev, "port %d link down\n", port);
+}
+
+void mt7620_mdio_link_adjust(struct fe_priv *priv, int port)
+{
+ mt7620_print_link_state(priv, port, priv->link[port],
+ priv->phy->speed[port],
+ (priv->phy->duplex[port] == DUPLEX_FULL));
+ mt7620_handle_carrier(priv);
+}
+
+static irqreturn_t gsw_interrupt_mt7620(int irq, void *_priv)
+{
+ struct fe_priv *priv = (struct fe_priv *)_priv;
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+ u32 status;
+ int i, max = (gsw->port4 == PORT4_EPHY) ? (4) : (3);
+
+ status = gsw_r32(gsw, GSW_REG_ISR);
+ if (status & PORT_IRQ_ST_CHG)
+ for (i = 0; i <= max; i++) {
+ u32 status = gsw_r32(gsw, GSW_REG_PORT_STATUS(i));
+ int link = status & 0x1;
+
+ if (link != priv->link[i])
+ mt7620_print_link_state(priv, i, link,
+ (status >> 2) & 3,
+ (status & 0x2));
+
+ priv->link[i] = link;
+ }
+ mt7620_handle_carrier(priv);
+
+ gsw_w32(gsw, status, GSW_REG_ISR);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t gsw_interrupt_mt7621(int irq, void *_priv)
+{
+ struct fe_priv *priv = (struct fe_priv *)_priv;
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+ u32 reg, i;
+
+ reg = mt7530_mdio_r32(gsw, 0x700c);
+
+ for (i = 0; i < 5; i++)
+ if (reg & BIT(i)) {
+ unsigned int link;
+
+ link = mt7530_mdio_r32(gsw,
+ 0x3008 + (i * 0x100)) & 0x1;
+
+ if (link != priv->link[i]) {
+ priv->link[i] = link;
+ if (link)
+ netdev_info(priv->netdev,
+ "port %d link up\n", i);
+ else
+ netdev_info(priv->netdev,
+ "port %d link down\n", i);
+ }
+ }
+
+ mt7620_handle_carrier(priv);
+ mt7530_mdio_w32(gsw, 0x700c, 0x1f);
+
+ return IRQ_HANDLED;
+}
+
+static int mt7620_is_bga(void)
+{
+ u32 bga = rt_sysc_r32(0x0c);
+
+ return (bga >> 16) & 1;
+}
+
+static void gsw_auto_poll(struct mt7620_gsw *gsw)
+{
+ int phy;
+ int lsb = -1, msb = 0;
+
+ for_each_set_bit(phy, &gsw->autopoll, 32) {
+ if (lsb < 0)
+ lsb = phy;
+ msb = phy;
+ }
+
+ if (lsb == msb)
+ lsb--;
+
+ gsw_w32(gsw, PHY_AN_EN | PHY_PRE_EN | PMY_MDC_CONF(5) |
+ (msb << 8) | lsb, ESW_PHY_POLLING);
+}
+
+void mt7620_port_init(struct fe_priv *priv, struct device_node *np)
+{
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+ const __be32 *_id = of_get_property(np, "reg", NULL);
+ int phy_mode, size, id;
+ int shift = 12;
+ u32 val, mask = 0;
+ int min = (gsw->port4 == PORT4_EPHY) ? (5) : (4);
+
+ if (!_id || (be32_to_cpu(*_id) < min) || (be32_to_cpu(*_id) > 5)) {
+ if (_id)
+ pr_err("%s: invalid port id %d\n", np->name,
+ be32_to_cpu(*_id));
+ else
+ pr_err("%s: invalid port id\n", np->name);
+ return;
+ }
+
+ id = be32_to_cpu(*_id);
+
+ if (id == 4)
+ shift = 14;
+
+ priv->phy->phy_fixed[id] = of_get_property(np, "ralink,fixed-link",
+ &size);
+ if (priv->phy->phy_fixed[id] &&
+ (size != (4 * sizeof(*priv->phy->phy_fixed[id])))) {
+ pr_err("%s: invalid fixed link property\n", np->name);
+ priv->phy->phy_fixed[id] = NULL;
+ return;
+ }
+
+ phy_mode = of_get_phy_mode(np);
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_RGMII:
+ mask = 0;
+ break;
+ case PHY_INTERFACE_MODE_MII:
+ mask = 1;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ mask = 2;
+ break;
+ default:
+ dev_err(priv->device, "port %d - invalid phy mode\n", id);
+ return;
+ }
+
+ priv->phy->phy_node[id] = of_parse_phandle(np, "phy-handle", 0);
+ if (!priv->phy->phy_node[id] && !priv->phy->phy_fixed[id])
+ return;
+
+ val = rt_sysc_r32(SYSC_REG_CFG1);
+ val &= ~(3 << shift);
+ val |= mask << shift;
+ rt_sysc_w32(val, SYSC_REG_CFG1);
+
+ if (priv->phy->phy_fixed[id]) {
+ const __be32 *link = priv->phy->phy_fixed[id];
+ int tx_fc, rx_fc;
+ u32 val = 0;
+
+ priv->phy->speed[id] = be32_to_cpup(link++);
+ tx_fc = be32_to_cpup(link++);
+ rx_fc = be32_to_cpup(link++);
+ priv->phy->duplex[id] = be32_to_cpup(link++);
+ priv->link[id] = 1;
+
+ switch (priv->phy->speed[id]) {
+ case SPEED_10:
+ val = 0;
+ break;
+ case SPEED_100:
+ val = 1;
+ break;
+ case SPEED_1000:
+ val = 2;
+ break;
+ default:
+ dev_err(priv->device, "invalid link speed: %d\n",
+ priv->phy->speed[id]);
+ priv->phy->phy_fixed[id] = 0;
+ return;
+ }
+ val = PMCR_SPEED(val);
+ val |= PMCR_LINK | PMCR_BACKPRES | PMCR_BACKOFF | PMCR_RX_EN |
+ PMCR_TX_EN | PMCR_FORCE | PMCR_MAC_MODE | PMCR_IPG;
+ if (tx_fc)
+ val |= PMCR_TX_FC;
+ if (rx_fc)
+ val |= PMCR_RX_FC;
+ if (priv->phy->duplex[id])
+ val |= PMCR_DUPLEX;
+ gsw_w32(gsw, val, GSW_REG_PORT_PMCR(id));
+ dev_info(priv->device, "using fixed link parameters\n");
+ return;
+ }
+
+ if (priv->phy->phy_node[id] && priv->mii_bus->phy_map[id]) {
+ u32 val = PMCR_BACKPRES | PMCR_BACKOFF | PMCR_RX_EN |
+ PMCR_TX_EN | PMCR_MAC_MODE | PMCR_IPG;
+
+ gsw_w32(gsw, val, GSW_REG_PORT_PMCR(id));
+ fe_connect_phy_node(priv, priv->phy->phy_node[id]);
+ gsw->autopoll |= BIT(id);
+ gsw_auto_poll(gsw);
+ return;
+ }
+}
+
+static void gsw_hw_init_mt7620(struct mt7620_gsw *gsw, struct device_node *np)
+{
+ u32 is_BGA = mt7620_is_bga();
+
+ rt_sysc_w32(rt_sysc_r32(SYSC_REG_CFG1) | BIT(8), SYSC_REG_CFG1);
+ gsw_w32(gsw, gsw_r32(gsw, GSW_REG_CKGCR) & ~(0x3 << 4), GSW_REG_CKGCR);
+
+ if (of_property_read_bool(np, "mediatek,mt7530")) {
+ u32 val;
+
+ /* turn off ephy and set phy base addr to 12 */
+ gsw_w32(gsw, gsw_r32(gsw, GSW_REG_GPC1) |
+ (0x1f << 24) | (0xc << 16),
+ GSW_REG_GPC1);
+
+ /* set MT7530 central align */
+ val = mt7530_mdio_r32(gsw, 0x7830);
+ val &= ~BIT(0);
+ val |= BIT(1);
+ mt7530_mdio_w32(gsw, 0x7830, val);
+
+ val = mt7530_mdio_r32(gsw, 0x7a40);
+ val &= ~BIT(30);
+ mt7530_mdio_w32(gsw, 0x7a40, val);
+
+ mt7530_mdio_w32(gsw, 0x7a78, 0x855);
+ } else {
+ /* EPHY1 fixup - only run if the ephy is enabled */
+
+ /* global page 4 */
+ _mt7620_mii_write(gsw, 1, 31, 0x4000);
+
+ _mt7620_mii_write(gsw, 1, 17, 0x7444);
+ if (is_BGA)
+ _mt7620_mii_write(gsw, 1, 19, 0x0114);
+ else
+ _mt7620_mii_write(gsw, 1, 19, 0x0117);
+
+ _mt7620_mii_write(gsw, 1, 22, 0x10cf);
+ _mt7620_mii_write(gsw, 1, 25, 0x6212);
+ _mt7620_mii_write(gsw, 1, 26, 0x0777);
+ _mt7620_mii_write(gsw, 1, 29, 0x4000);
+ _mt7620_mii_write(gsw, 1, 28, 0xc077);
+ _mt7620_mii_write(gsw, 1, 24, 0x0000);
+
+ /* global page 3 */
+ _mt7620_mii_write(gsw, 1, 31, 0x3000);
+ _mt7620_mii_write(gsw, 1, 17, 0x4838);
+
+ /* global page 2 */
+ _mt7620_mii_write(gsw, 1, 31, 0x2000);
+ if (is_BGA) {
+ _mt7620_mii_write(gsw, 1, 21, 0x0515);
+ _mt7620_mii_write(gsw, 1, 22, 0x0053);
+ _mt7620_mii_write(gsw, 1, 23, 0x00bf);
+ _mt7620_mii_write(gsw, 1, 24, 0x0aaf);
+ _mt7620_mii_write(gsw, 1, 25, 0x0fad);
+ _mt7620_mii_write(gsw, 1, 26, 0x0fc1);
+ } else {
+ _mt7620_mii_write(gsw, 1, 21, 0x0517);
+ _mt7620_mii_write(gsw, 1, 22, 0x0fd2);
+ _mt7620_mii_write(gsw, 1, 23, 0x00bf);
+ _mt7620_mii_write(gsw, 1, 24, 0x0aab);
+ _mt7620_mii_write(gsw, 1, 25, 0x00ae);
+ _mt7620_mii_write(gsw, 1, 26, 0x0fff);
+ }
+ /* global page 1 */
+ _mt7620_mii_write(gsw, 1, 31, 0x1000);
+ _mt7620_mii_write(gsw, 1, 17, 0xe7f8);
+ }
+
+ /* global page 0 */
+ _mt7620_mii_write(gsw, 1, 31, 0x8000);
+ _mt7620_mii_write(gsw, 0, 30, 0xa000);
+ _mt7620_mii_write(gsw, 1, 30, 0xa000);
+ _mt7620_mii_write(gsw, 2, 30, 0xa000);
+ _mt7620_mii_write(gsw, 3, 30, 0xa000);
+
+ _mt7620_mii_write(gsw, 0, 4, 0x05e1);
+ _mt7620_mii_write(gsw, 1, 4, 0x05e1);
+ _mt7620_mii_write(gsw, 2, 4, 0x05e1);
+ _mt7620_mii_write(gsw, 3, 4, 0x05e1);
+
+ /* global page 2 */
+ _mt7620_mii_write(gsw, 1, 31, 0xa000);
+ _mt7620_mii_write(gsw, 0, 16, 0x1111);
+ _mt7620_mii_write(gsw, 1, 16, 0x1010);
+ _mt7620_mii_write(gsw, 2, 16, 0x1515);
+ _mt7620_mii_write(gsw, 3, 16, 0x0f0f);
+
+ /* CPU Port6 Force Link 1G, FC ON */
+ gsw_w32(gsw, 0x5e33b, GSW_REG_PORT_PMCR(6));
+
+ /* Set Port 6 as CPU Port */
+ gsw_w32(gsw, 0x7f7f7fe0, 0x0010);
+
+ /* setup port 4 */
+ if (gsw->port4 == PORT4_EPHY) {
+ u32 val = rt_sysc_r32(SYSC_REG_CFG1);
+
+ val |= 3 << 14;
+ rt_sysc_w32(val, SYSC_REG_CFG1);
+ _mt7620_mii_write(gsw, 4, 30, 0xa000);
+ _mt7620_mii_write(gsw, 4, 4, 0x05e1);
+ _mt7620_mii_write(gsw, 4, 16, 0x1313);
+ pr_info("gsw: setting port4 to ephy mode\n");
+ }
+}
+
+static void gsw_hw_init_mt7621(struct mt7620_gsw *gsw, struct device_node *np)
+{
+ u32 i;
+ u32 val;
+
+ /* wardware reset the switch */
+ fe_reset(RST_CTRL_MCM);
+ mdelay(10);
+
+ /* reduce RGMII2 PAD driving strength */
+ rt_sysc_m32(3 << 4, 0, SYSC_PAD_RGMII2_MDIO);
+
+ /* gpio mux - RGMII1=Normal mode */
+ rt_sysc_m32(BIT(14), 0, SYSC_GPIO_MODE);
+
+ /* set GMAC1 RGMII mode */
+ rt_sysc_m32(3 << 12, 0, SYSC_REG_CFG1);
+
+ /* enable MDIO to control MT7530 */
+ rt_sysc_m32(3 << 12, 0, SYSC_GPIO_MODE);
+
+ /* turn off all PHYs */
+ for (i = 0; i <= 4; i++) {
+ val = _mt7620_mii_read(gsw, i, 0x0);
+ val |= BIT(11);
+ _mt7620_mii_write(gsw, i, 0x0, val);
+ }
+
+ /* reset the switch */
+ mt7530_mdio_w32(gsw, 0x7000, 0x3);
+ usleep_range(10, 20);
+
+ if ((rt_sysc_r32(SYSC_REG_CHIP_REV_ID) & 0xFFFF) == 0x0101) {
+ /* (GE1, Force 1000M/FD, FC ON, MAX_RX_LENGTH 1536) */
+ gsw_w32(gsw, 0x2105e30b, 0x100);
+ mt7530_mdio_w32(gsw, 0x3600, 0x5e30b);
+ } else {
+ /* (GE1, Force 1000M/FD, FC ON, MAX_RX_LENGTH 1536) */
+ gsw_w32(gsw, 0x2105e33b, 0x100);
+ mt7530_mdio_w32(gsw, 0x3600, 0x5e33b);
+ }
+
+ /* (GE2, Link down) */
+ gsw_w32(gsw, 0x8000, 0x200);
+
+ /* Enable Port 6, P5 as GMAC5, P5 disable */
+ val = mt7530_mdio_r32(gsw, 0x7804);
+ val &= ~BIT(8);
+ val |= BIT(6) | BIT(13) | BIT(16);
+ mt7530_mdio_w32(gsw, 0x7804, val);
+
+ val = rt_sysc_r32(0x10);
+ val = (val >> 6) & 0x7;
+ if (val >= 6) {
+ /* 25Mhz Xtal - do nothing */
+ } else if (val >= 3) {
+ /* 40Mhz */
+
+ /* disable MT7530 core clock */
+ _mt7620_mii_write(gsw, 0, 13, 0x1f);
+ _mt7620_mii_write(gsw, 0, 14, 0x410);
+ _mt7620_mii_write(gsw, 0, 13, 0x401f);
+ _mt7620_mii_write(gsw, 0, 14, 0x0);
+
+ /* disable MT7530 PLL */
+ _mt7620_mii_write(gsw, 0, 13, 0x1f);
+ _mt7620_mii_write(gsw, 0, 14, 0x40d);
+ _mt7620_mii_write(gsw, 0, 13, 0x401f);
+ _mt7620_mii_write(gsw, 0, 14, 0x2020);
+
+ /* for MT7530 core clock = 500Mhz */
+ _mt7620_mii_write(gsw, 0, 13, 0x1f);
+ _mt7620_mii_write(gsw, 0, 14, 0x40e);
+ _mt7620_mii_write(gsw, 0, 13, 0x401f);
+ _mt7620_mii_write(gsw, 0, 14, 0x119);
+
+ /* enable MT7530 PLL */
+ _mt7620_mii_write(gsw, 0, 13, 0x1f);
+ _mt7620_mii_write(gsw, 0, 14, 0x40d);
+ _mt7620_mii_write(gsw, 0, 13, 0x401f);
+ _mt7620_mii_write(gsw, 0, 14, 0x2820);
+
+ usleep_range(20, 40);
+
+ /* enable MT7530 core clock */
+ _mt7620_mii_write(gsw, 0, 13, 0x1f);
+ _mt7620_mii_write(gsw, 0, 14, 0x410);
+ _mt7620_mii_write(gsw, 0, 13, 0x401f);
+ } else {
+ /* 20Mhz Xtal - TODO */
+ }
+
+ /* RGMII */
+ _mt7620_mii_write(gsw, 0, 14, 0x1);
+
+ /* set MT7530 central align */
+ val = mt7530_mdio_r32(gsw, 0x7830);
+ val &= ~BIT(0);
+ val |= BIT(1);
+ mt7530_mdio_w32(gsw, 0x7830, val);
+ val = mt7530_mdio_r32(gsw, 0x7a40);
+ val &= ~BIT(30);
+ mt7530_mdio_w32(gsw, 0x7a40, val);
+ mt7530_mdio_w32(gsw, 0x7a78, 0x855);
+
+ /* delay setting for 10/1000M */
+ mt7530_mdio_w32(gsw, 0x7b00, 0x102);
+ mt7530_mdio_w32(gsw, 0x7b04, 0x14);
+
+ /* lower Tx Driving*/
+ mt7530_mdio_w32(gsw, 0x7a54, 0x44);
+ mt7530_mdio_w32(gsw, 0x7a5c, 0x44);
+ mt7530_mdio_w32(gsw, 0x7a64, 0x44);
+ mt7530_mdio_w32(gsw, 0x7a6c, 0x44);
+ mt7530_mdio_w32(gsw, 0x7a74, 0x44);
+ mt7530_mdio_w32(gsw, 0x7a7c, 0x44);
+
+ /* turn on all PHYs */
+ for (i = 0; i <= 4; i++) {
+ val = _mt7620_mii_read(gsw, i, 0);
+ val &= ~BIT(11);
+ _mt7620_mii_write(gsw, i, 0, val);
+ }
+
+ /* enable irq */
+ val = mt7530_mdio_r32(gsw, 0x7808);
+ val |= 3 << 16;
+ mt7530_mdio_w32(gsw, 0x7808, val);
+}
+
+void mt7620_set_mac(struct fe_priv *priv, unsigned char *mac)
+{
+ struct mt7620_gsw *gsw = (struct mt7620_gsw *)priv->soc->swpriv;
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->page_lock, flags);
+ gsw_w32(gsw, (mac[0] << 8) | mac[1], GSW_REG_SMACCR1);
+ gsw_w32(gsw, (mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5],
+ GSW_REG_SMACCR0);
+ spin_unlock_irqrestore(&priv->page_lock, flags);
+}
+
+static const struct of_device_id gsw_match[] = {
+ { .compatible = "mediatek,mt7620-gsw" },
+ {}
+};
+
+int mt7620_gsw_probe(struct fe_priv *priv)
+{
+ struct mt7620_gsw *gsw;
+ struct device_node *np;
+ const char *port4 = NULL;
+
+ np = of_find_matching_node(NULL, gsw_match);
+ if (!np) {
+ dev_err(priv->device, "no gsw node found\n");
+ return -EINVAL;
+ }
+ np = of_node_get(np);
+
+ gsw = devm_kzalloc(priv->device, sizeof(struct mt7620_gsw), GFP_KERNEL);
+ if (!gsw)
+ return -ENOMEM;
+
+ gsw->base = of_iomap(np, 0);
+ if (!gsw->base) {
+ dev_err(priv->device, "gsw ioremap failed\n");
+ return -ENOMEM;
+ }
+
+ gsw->dev = priv->device;
+ priv->soc->swpriv = gsw;
+
+ of_property_read_string(np, "mediatek,port4", &port4);
+ if (port4 && !strcmp(port4, "ephy"))
+ gsw->port4 = PORT4_EPHY;
+ else if (port4 && !strcmp(port4, "gmac"))
+ gsw->port4 = PORT4_EXT;
+ else
+ gsw->port4 = PORT4_EPHY;
+
+ if (IS_ENABLED(CONFIG_SOC_MT7620))
+ gsw_hw_init_mt7620(gsw, np);
+ else
+ gsw_hw_init_mt7621(gsw, np);
+
+ gsw->irq = irq_of_parse_and_map(np, 0);
+ if (gsw->irq) {
+ if (IS_ENABLED(CONFIG_SOC_MT7620)) {
+ request_irq(gsw->irq, gsw_interrupt_mt7620, 0,
+ "gsw", priv);
+ gsw_w32(gsw, ~PORT_IRQ_ST_CHG, GSW_REG_IMR);
+ } else {
+ request_irq(gsw->irq, gsw_interrupt_mt7621, 0,
+ "gsw", priv);
+ mt7530_mdio_w32(gsw, 0x7008, 0x1f);
+ }
+ }
+
+ return 0;
+}
diff --git a/drivers/net/ethernet/ralink/gsw_mt7620.h b/drivers/net/ethernet/ralink/gsw_mt7620.h
new file mode 100644
index 0000000..9a42332
--- /dev/null
+++ b/drivers/net/ethernet/ralink/gsw_mt7620.h
@@ -0,0 +1,26 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#ifndef _RALINK_GSW_MT7620_H__
+#define _RALINK_GSW_MT7620_H__
+
+int mt7620_gsw_probe(struct fe_priv *priv);
+void mt7620_set_mac(struct fe_priv *priv, unsigned char *mac);
+int mt7620_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, u16 val);
+int mt7620_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg);
+void mt7620_mdio_link_adjust(struct fe_priv *priv, int port);
+void mt7620_port_init(struct fe_priv *priv, struct device_node *np);
+int mt7620a_has_carrier(struct fe_priv *priv);
+
+#endif
diff --git a/drivers/net/ethernet/ralink/soc_mt7620.c b/drivers/net/ethernet/ralink/soc_mt7620.c
new file mode 100644
index 0000000..baced12
--- /dev/null
+++ b/drivers/net/ethernet/ralink/soc_mt7620.c
@@ -0,0 +1,273 @@
+/* This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Copyright (C) 2009-2015 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2009-2015 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2013-2015 Michael Lee <igvtee@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/if_vlan.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include <mt7620.h>
+#include "ralink_soc_eth.h"
+#include "gsw_mt7620.h"
+
+#define MT7620A_CDMA_CSG_CFG 0x400
+#define MT7620_DMA_VID (MT7620A_CDMA_CSG_CFG | 0x30)
+#define MT7621_CDMP_IG_CTRL (MT7620A_CDMA_CSG_CFG + 0x00)
+#define MT7621_CDMP_EG_CTRL (MT7620A_CDMA_CSG_CFG + 0x04)
+#define MT7620A_RESET_FE BIT(21)
+#define MT7621_RESET_FE BIT(6)
+#define MT7620A_RESET_ESW BIT(23)
+#define MT7620_L4_VALID BIT(23)
+#define MT7621_L4_VALID BIT(24)
+
+#define MT7620_TX_DMA_UDF BIT(15)
+#define MT7621_TX_DMA_UDF BIT(19)
+#define TX_DMA_FP_BMAP ((0xff) << 19)
+
+#define CDMA_ICS_EN BIT(2)
+#define CDMA_UCS_EN BIT(1)
+#define CDMA_TCS_EN BIT(0)
+
+#define GDMA_ICS_EN BIT(22)
+#define GDMA_TCS_EN BIT(21)
+#define GDMA_UCS_EN BIT(20)
+
+/* frame engine counters */
+#define MT7620_REG_MIB_OFFSET 0x1000
+#define MT7620_PPE_AC_BCNT0 (MT7620_REG_MIB_OFFSET + 0x00)
+#define MT7620_GDM1_TX_GBCNT (MT7620_REG_MIB_OFFSET + 0x300)
+#define MT7620_GDM2_TX_GBCNT (MT7620_GDM1_TX_GBCNT + 0x40)
+
+#define MT7621_REG_MIB_OFFSET 0x2000
+#define MT7621_PPE_AC_BCNT0 (MT7621_REG_MIB_OFFSET + 0x00)
+#define MT7621_GDM1_TX_GBCNT (MT7621_REG_MIB_OFFSET + 0x400)
+#define MT7621_GDM2_TX_GBCNT (MT7621_GDM1_TX_GBCNT + 0x40)
+
+#define GSW_REG_GDMA1_MAC_ADRL 0x508
+#define GSW_REG_GDMA1_MAC_ADRH 0x50C
+
+#define MT7621_FE_RST_GL (FE_FE_OFFSET + 0x04)
+#define MT7620_FE_INT_STATUS2 (FE_FE_OFFSET + 0x08)
+
+/* FE_INT_STATUS reg on mt7620 define CNT_GDM1_AF at BIT(29)
+ * but after test it should be BIT(13).
+ */
+#define MT7620_FE_GDM1_AF BIT(13)
+#define MT7621_FE_GDM1_AF BIT(28)
+#define MT7621_FE_GDM2_AF BIT(29)
+
+static const u16 mt7620_reg_table[FE_REG_COUNT] = {
+ [FE_REG_PDMA_GLO_CFG] = RT5350_PDMA_GLO_CFG,
+ [FE_REG_PDMA_RST_CFG] = RT5350_PDMA_RST_CFG,
+ [FE_REG_DLY_INT_CFG] = RT5350_DLY_INT_CFG,
+ [FE_REG_TX_BASE_PTR0] = RT5350_TX_BASE_PTR0,
+ [FE_REG_TX_MAX_CNT0] = RT5350_TX_MAX_CNT0,
+ [FE_REG_TX_CTX_IDX0] = RT5350_TX_CTX_IDX0,
+ [FE_REG_TX_DTX_IDX0] = RT5350_TX_DTX_IDX0,
+ [FE_REG_RX_BASE_PTR0] = RT5350_RX_BASE_PTR0,
+ [FE_REG_RX_MAX_CNT0] = RT5350_RX_MAX_CNT0,
+ [FE_REG_RX_CALC_IDX0] = RT5350_RX_CALC_IDX0,
+ [FE_REG_RX_DRX_IDX0] = RT5350_RX_DRX_IDX0,
+ [FE_REG_FE_INT_ENABLE] = RT5350_FE_INT_ENABLE,
+ [FE_REG_FE_INT_STATUS] = RT5350_FE_INT_STATUS,
+ [FE_REG_FE_DMA_VID_BASE] = MT7620_DMA_VID,
+ [FE_REG_FE_COUNTER_BASE] = MT7620_GDM1_TX_GBCNT,
+ [FE_REG_FE_RST_GL] = MT7621_FE_RST_GL,
+ [FE_REG_FE_INT_STATUS2] = MT7620_FE_INT_STATUS2,
+};
+
+static const u16 mt7621_reg_table[FE_REG_COUNT] = {
+ [FE_REG_PDMA_GLO_CFG] = RT5350_PDMA_GLO_CFG,
+ [FE_REG_PDMA_RST_CFG] = RT5350_PDMA_RST_CFG,
+ [FE_REG_DLY_INT_CFG] = RT5350_DLY_INT_CFG,
+ [FE_REG_TX_BASE_PTR0] = RT5350_TX_BASE_PTR0,
+ [FE_REG_TX_MAX_CNT0] = RT5350_TX_MAX_CNT0,
+ [FE_REG_TX_CTX_IDX0] = RT5350_TX_CTX_IDX0,
+ [FE_REG_TX_DTX_IDX0] = RT5350_TX_DTX_IDX0,
+ [FE_REG_RX_BASE_PTR0] = RT5350_RX_BASE_PTR0,
+ [FE_REG_RX_MAX_CNT0] = RT5350_RX_MAX_CNT0,
+ [FE_REG_RX_CALC_IDX0] = RT5350_RX_CALC_IDX0,
+ [FE_REG_RX_DRX_IDX0] = RT5350_RX_DRX_IDX0,
+ [FE_REG_FE_INT_ENABLE] = RT5350_FE_INT_ENABLE,
+ [FE_REG_FE_INT_STATUS] = RT5350_FE_INT_STATUS,
+ [FE_REG_FE_DMA_VID_BASE] = 0,
+ [FE_REG_FE_COUNTER_BASE] = MT7621_GDM1_TX_GBCNT,
+ [FE_REG_FE_RST_GL] = MT7621_FE_RST_GL,
+ [FE_REG_FE_INT_STATUS2] = MT7620_FE_INT_STATUS2,
+};
+
+static void mt7620_fe_reset(void)
+{
+ fe_reset(MT7620A_RESET_FE | MT7620A_RESET_ESW);
+}
+
+static void mt7621_fe_reset(void)
+{
+ fe_reset(MT7621_RESET_FE);
+}
+
+static void mt7620_rxcsum_config(bool enable)
+{
+ if (enable)
+ fe_w32(fe_r32(MT7620A_GDMA1_FWD_CFG) | (GDMA_ICS_EN |
+ GDMA_TCS_EN | GDMA_UCS_EN),
+ MT7620A_GDMA1_FWD_CFG);
+ else
+ fe_w32(fe_r32(MT7620A_GDMA1_FWD_CFG) & ~(GDMA_ICS_EN |
+ GDMA_TCS_EN | GDMA_UCS_EN),
+ MT7620A_GDMA1_FWD_CFG);
+}
+
+static void mt7620_txcsum_config(bool enable)
+{
+ if (enable)
+ fe_w32(fe_r32(MT7620A_CDMA_CSG_CFG) | (CDMA_ICS_EN |
+ CDMA_UCS_EN | CDMA_TCS_EN),
+ MT7620A_CDMA_CSG_CFG);
+ else
+ fe_w32(fe_r32(MT7620A_CDMA_CSG_CFG) & ~(CDMA_ICS_EN |
+ CDMA_UCS_EN | CDMA_TCS_EN),
+ MT7620A_CDMA_CSG_CFG);
+}
+
+static void mt7621_rxvlan_config(bool enable)
+{
+ if (enable)
+ fe_w32(1, MT7621_CDMP_EG_CTRL);
+ else
+ fe_w32(0, MT7621_CDMP_EG_CTRL);
+}
+
+static int mt7620_fwd_config(struct fe_priv *priv)
+{
+ struct net_device *dev = priv_netdev(priv);
+
+ fe_w32(fe_r32(MT7620A_GDMA1_FWD_CFG) & ~7, MT7620A_GDMA1_FWD_CFG);
+
+ mt7620_txcsum_config((dev->features & NETIF_F_IP_CSUM));
+ mt7620_rxcsum_config((dev->features & NETIF_F_RXCSUM));
+
+ return 0;
+}
+
+static int mt7621_fwd_config(struct fe_priv *priv)
+{
+ struct net_device *dev = priv_netdev(priv);
+
+ fe_w32(fe_r32(MT7620A_GDMA1_FWD_CFG) & ~0xffff,
+ MT7620A_GDMA1_FWD_CFG);
+
+ /* mt7621 don't have txcsum config */
+ mt7620_rxcsum_config((dev->features & NETIF_F_RXCSUM));
+ mt7621_rxvlan_config((dev->features & NETIF_F_HW_VLAN_CTAG_RX) &&
+ (priv->flags & FE_FLAG_RX_VLAN_CTAG));
+
+ return 0;
+}
+
+static void mt7620_tx_dma(struct fe_tx_dma *txd)
+{
+}
+
+static void mt7621_tx_dma(struct fe_tx_dma *txd)
+{
+ txd->txd4 = BIT(25);
+}
+
+static void mt7620_init_data(struct fe_soc_data *data,
+ struct net_device *netdev)
+{
+ struct fe_priv *priv = netdev_priv(netdev);
+
+ priv->flags = FE_FLAG_PADDING_64B | FE_FLAG_RX_2B_OFFSET |
+ FE_FLAG_RX_SG_DMA;
+
+ netdev->hw_features = NETIF_F_IP_CSUM | NETIF_F_RXCSUM |
+ NETIF_F_HW_VLAN_CTAG_TX;
+ if (mt7620_get_eco() >= 5)
+ netdev->hw_features |= NETIF_F_SG | NETIF_F_TSO | NETIF_F_TSO6 |
+ NETIF_F_IPV6_CSUM;
+}
+
+static void mt7621_init_data(struct fe_soc_data *data,
+ struct net_device *netdev)
+{
+ struct fe_priv *priv = netdev_priv(netdev);
+
+ priv->flags = FE_FLAG_PADDING_64B | FE_FLAG_RX_2B_OFFSET |
+ FE_FLAG_RX_SG_DMA | FE_FLAG_NAPI_WEIGHT;
+
+ netdev->hw_features = NETIF_F_IP_CSUM | NETIF_F_RXCSUM |
+ NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_SG | NETIF_F_TSO |
+ NETIF_F_TSO6 | NETIF_F_IPV6_CSUM;
+}
+
+static void mt7621_set_mac(struct fe_priv *priv, unsigned char *mac)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->page_lock, flags);
+ fe_w32((mac[0] << 8) | mac[1], GSW_REG_GDMA1_MAC_ADRH);
+ fe_w32((mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5],
+ GSW_REG_GDMA1_MAC_ADRL);
+ spin_unlock_irqrestore(&priv->page_lock, flags);
+}
+
+static struct fe_soc_data mt7620_data = {
+ .init_data = mt7620_init_data,
+ .reset_fe = mt7620_fe_reset,
+ .set_mac = mt7620_set_mac,
+ .fwd_config = mt7620_fwd_config,
+ .tx_dma = mt7620_tx_dma,
+ .switch_init = mt7620_gsw_probe,
+ .port_init = mt7620_port_init,
+ .reg_table = mt7620_reg_table,
+ .pdma_glo_cfg = FE_PDMA_SIZE_16DWORDS,
+ .rx_int = RT5350_RX_DONE_INT,
+ .tx_int = RT5350_TX_DONE_INT,
+ .status_int = MT7620_FE_GDM1_AF,
+ .checksum_bit = MT7620_L4_VALID,
+ .has_carrier = mt7620a_has_carrier,
+ .mdio_read = mt7620_mdio_read,
+ .mdio_write = mt7620_mdio_write,
+ .mdio_adjust_link = mt7620_mdio_link_adjust,
+};
+
+static struct fe_soc_data mt7621_data = {
+ .init_data = mt7621_init_data,
+ .reset_fe = mt7621_fe_reset,
+ .set_mac = mt7621_set_mac,
+ .fwd_config = mt7621_fwd_config,
+ .tx_dma = mt7621_tx_dma,
+ .switch_init = mt7620_gsw_probe,
+ .reg_table = mt7621_reg_table,
+ .pdma_glo_cfg = FE_PDMA_SIZE_16DWORDS,
+ .rx_int = RT5350_RX_DONE_INT,
+ .tx_int = RT5350_TX_DONE_INT,
+ .status_int = (MT7621_FE_GDM1_AF | MT7621_FE_GDM2_AF),
+ .checksum_bit = MT7621_L4_VALID,
+ .has_carrier = mt7620a_has_carrier,
+ .mdio_read = mt7620_mdio_read,
+ .mdio_write = mt7620_mdio_write,
+ .mdio_adjust_link = mt7620_mdio_link_adjust,
+};
+
+const struct of_device_id of_fe_match[] = {
+ { .compatible = "mediatek,mt7620-eth", .data = &mt7620_data },
+ { .compatible = "mediatek,mt7621-eth", .data = &mt7621_data },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, of_fe_match);
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC 8/8] net-next: ralink: add Kconfig and Makefile
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
` (5 preceding siblings ...)
2015-11-22 8:40 ` [RFC 7/8] net-next: ralink: add support for mt7620 family John Crispin
@ 2015-11-22 8:40 ` John Crispin
6 siblings, 0 replies; 13+ messages in thread
From: John Crispin @ 2015-11-22 8:40 UTC (permalink / raw)
To: David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
Steven Liu (劉人豪),
Fred Chang (張嘉宏),
John Crispin
This patch adds the Makefile and Kconfig required to make the driver build.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
---
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/ralink/Kconfig | 49 ++++++++++++++++++++++++++++++++++
drivers/net/ethernet/ralink/Makefile | 19 +++++++++++++
4 files changed, 70 insertions(+)
create mode 100644 drivers/net/ethernet/ralink/Kconfig
create mode 100644 drivers/net/ethernet/ralink/Makefile
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 955d06b..2d24101 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -153,6 +153,7 @@ source "drivers/net/ethernet/packetengines/Kconfig"
source "drivers/net/ethernet/pasemi/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/qualcomm/Kconfig"
+source "drivers/net/ethernet/ralink/Kconfig"
source "drivers/net/ethernet/realtek/Kconfig"
source "drivers/net/ethernet/renesas/Kconfig"
source "drivers/net/ethernet/rdc/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 4a2ee98..fba816c 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_NET_PACKET_ENGINE) += packetengines/
obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_QUALCOMM) += qualcomm/
+obj-$(CONFIG_NET_RALINK) += ralink/
obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
obj-$(CONFIG_NET_VENDOR_RENESAS) += renesas/
obj-$(CONFIG_NET_VENDOR_RDC) += rdc/
diff --git a/drivers/net/ethernet/ralink/Kconfig b/drivers/net/ethernet/ralink/Kconfig
new file mode 100644
index 0000000..09639cd
--- /dev/null
+++ b/drivers/net/ethernet/ralink/Kconfig
@@ -0,0 +1,49 @@
+config NET_RALINK
+ tristate "Ralink ethernet driver"
+ depends on RALINK
+ help
+ This driver supports the ethernet mac inside the ralink wisocs
+
+if NET_RALINK
+choice
+ prompt "MAC type"
+
+config NET_RALINK_RT2880
+ bool "RT2882"
+ depends on SOC_RT288X
+
+config NET_RALINK_RT3050
+ bool "RT3050/MT7628"
+ depends on (SOC_RT305X || SOC_MT7620)
+
+config NET_RALINK_RT3883
+ bool "RT3883"
+ depends on SOC_RT3883
+
+config NET_RALINK_MT7620
+ bool "MT7620"
+ depends on (SOC_MT7620 || SOC_MT7621)
+
+endchoice
+
+config NET_RALINK_MDIO
+ def_bool NET_RALINK
+ depends on (NET_RALINK_RT2880 || NET_RALINK_RT3883 || NET_RALINK_MT7620 || NET_RALINK_MT7621)
+ select PHYLIB
+
+config NET_RALINK_MDIO_RT2880
+ def_bool NET_RALINK
+ depends on (NET_RALINK_RT2880 || NET_RALINK_RT3883)
+ select NET_RALINK_MDIO
+
+config NET_RALINK_ESW_RT3050
+ def_bool NET_RALINK
+ depends on NET_RALINK_RT3050
+ select PHYLIB
+
+config NET_RALINK_GSW_MT7620
+ def_bool NET_RALINK
+ depends on NET_RALINK_MT7620 || NET_RALINK_MT7621
+ select NET_RALINK_MDIO
+ select PHYLIB
+endif
diff --git a/drivers/net/ethernet/ralink/Makefile b/drivers/net/ethernet/ralink/Makefile
new file mode 100644
index 0000000..eb90c56
--- /dev/null
+++ b/drivers/net/ethernet/ralink/Makefile
@@ -0,0 +1,19 @@
+#
+# Makefile for the Ralink SoCs built-in ethernet macs
+#
+
+ralink-eth-y += ralink_soc_eth.o ralink_ethtool.o
+
+ralink-eth-$(CONFIG_NET_RALINK_MDIO) += mdio.o
+ralink-eth-$(CONFIG_NET_RALINK_MDIO_RT2880) += mdio_rt2880.o
+
+ralink-eth-$(CONFIG_NET_RALINK_ESW_RT3050) += esw_rt3050.o
+ralink-eth-$(CONFIG_NET_RALINK_GSW_MT7620) += gsw_mt7620.o
+
+ralink-eth-$(CONFIG_NET_RALINK_RT2880) += soc_rt2880.o
+ralink-eth-$(CONFIG_NET_RALINK_RT3050) += soc_rt3050.o
+ralink-eth-$(CONFIG_NET_RALINK_RT3883) += soc_rt3883.o
+ralink-eth-$(CONFIG_NET_RALINK_MT7620) += soc_mt7620.o
+ralink-eth-$(CONFIG_NET_RALINK_MT7621) += soc_mt7621.o
+
+obj-$(CONFIG_NET_RALINK) += ralink-eth.o
--
1.7.10.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [RFC 5/8] net-next: ralink: add support for rt3050 family
2015-11-22 8:40 ` [RFC 5/8] net-next: ralink: add support for rt3050 family John Crispin
@ 2015-11-22 16:36 ` Andrew Lunn
2015-11-22 19:06 ` John Crispin
0 siblings, 1 reply; 13+ messages in thread
From: Andrew Lunn @ 2015-11-22 16:36 UTC (permalink / raw)
To: John Crispin
Cc: David S. Miller, netdev, Michael Lee, Felix Fietkau,
Steven Liu (?????????), Fred Chang (?????????)
On Sun, Nov 22, 2015 at 09:40:55AM +0100, John Crispin wrote:
> Add support for SoCs from the rt3050 family. This include rt3050, rt3052,
> rt3352 and rt5350. These all have a builtin 5 port 100mbit switch. This patch
> includes rudimentary code to power up the switch.
Hi John
How do you plan to control this switch?
Does it make sense to write a DSA driver for it?
Andrew
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC 5/8] net-next: ralink: add support for rt3050 family
2015-11-22 16:36 ` Andrew Lunn
@ 2015-11-22 19:06 ` John Crispin
2015-11-22 23:16 ` Andrew Lunn
0 siblings, 1 reply; 13+ messages in thread
From: John Crispin @ 2015-11-22 19:06 UTC (permalink / raw)
To: Andrew Lunn
Cc: David S. Miller, netdev, Michael Lee, Felix Fietkau,
Steven Liu (?????????), Fred Chang (?????????)
On 22/11/2015 17:36, Andrew Lunn wrote:
> On Sun, Nov 22, 2015 at 09:40:55AM +0100, John Crispin wrote:
>> Add support for SoCs from the rt3050 family. This include rt3050, rt3052,
>> rt3352 and rt5350. These all have a builtin 5 port 100mbit switch. This patch
>> includes rudimentary code to power up the switch.
>
> Hi John
>
> How do you plan to control this switch?
>
> Does it make sense to write a DSA driver for it?
>
> Andrew
>
Hi Andrew,
we have had a switch layer inside openwrt called swconfig for several
years. at the moment i have an add-on patch in openwrt to provide an
userland interface via that layer. the driver i have sent will bring up
the switch to a point where traffic flow is possible.
John
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC 5/8] net-next: ralink: add support for rt3050 family
2015-11-22 19:06 ` John Crispin
@ 2015-11-22 23:16 ` Andrew Lunn
2015-11-23 6:47 ` John Crispin
0 siblings, 1 reply; 13+ messages in thread
From: Andrew Lunn @ 2015-11-22 23:16 UTC (permalink / raw)
To: John Crispin
Cc: David S. Miller, netdev, Michael Lee, Felix Fietkau,
Steven Liu (?????????), Fred Chang (?????????)
> Hi Andrew,
>
> we have had a switch layer inside openwrt called swconfig for several
> years. at the moment i have an add-on patch in openwrt to provide an
> userland interface via that layer.
Hi John
I know of swconfig. However, it has been NACKed for mainline. So you
either need to do switchdev or DSA for controlling switches in
mainline.
Andrew
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC 5/8] net-next: ralink: add support for rt3050 family
2015-11-22 23:16 ` Andrew Lunn
@ 2015-11-23 6:47 ` John Crispin
0 siblings, 0 replies; 13+ messages in thread
From: John Crispin @ 2015-11-23 6:47 UTC (permalink / raw)
To: Andrew Lunn
Cc: David S. Miller, netdev, Michael Lee, Felix Fietkau,
Steven Liu (?????????), Fred Chang (?????????)
On 23/11/2015 00:16, Andrew Lunn wrote:
>> Hi Andrew,
>>
>> we have had a switch layer inside openwrt called swconfig for several
>> years. at the moment i have an add-on patch in openwrt to provide an
>> userland interface via that layer.
>
> Hi John
>
> I know of swconfig. However, it has been NACKed for mainline. So you
> either need to do switchdev or DSA for controlling switches in
> mainline.
>
> Andrew
>
Hi Andrew.
I am not planning to bring the switch support upstream in the near
future. right now my focus is on bringing the core driver upstream. once
that is done i plan so add support for the new DMA core, then the new
ARM SoCs. once those are done i plan to add support for the new media
center SoC and once that is done i am probably going to have a go at the
hw offloading engine. Once all that is done, i will have time to look at
the switch driver. however that wont happen in the near future.
John
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached
2015-11-22 8:40 ` [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached John Crispin
@ 2015-11-24 18:42 ` Florian Fainelli
0 siblings, 0 replies; 13+ messages in thread
From: Florian Fainelli @ 2015-11-24 18:42 UTC (permalink / raw)
To: John Crispin, David S. Miller
Cc: netdev, Michael Lee, Felix Fietkau,
"Steven Liu (劉人豪)",
"Fred Chang (張嘉宏)",
Andrew Lunn, jogo
On 22/11/15 00:40, John Crispin wrote:
> A network core might have more than one phy attached to its cpu port via a
> switch. The current code will set the carrier state to on/off when ever a
> cable is plugged into any of these ports.
Not really, no. The current PHY library implementation does not allow
more than one net_device instance to be bound to multiple PHY devices.
Since this is an integrated switch, you should really expose per-port
network devices, that is the paradigm we settled down on using for
Ethernet switches now (irrespective of using DSA or switchdev, or both).
>
> The patch adds a new bool that allows the driver to tell the phy_device to not
> set the carrier state. Instead the driver can manually handle the carrier
> state.
I am missing the bigger picture of how this is used, also, if link down
is a problem, would not link up be for the same reasons?
>
> Signed-off-by: John Crispin <blogic@openwrt.org>
> Signed-off-by: Felix Fietkau <nbd@openwrt.org>
> Signed-off-by: Michael Lee <igvtee@gmail.com>
> Cc: Florian Fainelli <f.fainelli@gmail.com>
> ---
> drivers/net/phy/phy.c | 9 ++++++---
> include/linux/phy.h | 1 +
> 2 files changed, 7 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> index 48ce6ef..bd2df40 100644
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c
> @@ -843,7 +843,8 @@ void phy_state_machine(struct work_struct *work)
> /* If the link is down, give up on negotiation for now */
> if (!phydev->link) {
> phydev->state = PHY_NOLINK;
> - netif_carrier_off(phydev->attached_dev);
> + if (!phydev->no_auto_carrier_off)
> + netif_carrier_off(phydev->attached_dev);
> phydev->adjust_link(phydev->attached_dev);
> break;
> }
> @@ -926,7 +927,8 @@ void phy_state_machine(struct work_struct *work)
> netif_carrier_on(phydev->attached_dev);
> } else {
> phydev->state = PHY_NOLINK;
> - netif_carrier_off(phydev->attached_dev);
> + if (!phydev->no_auto_carrier_off)
> + netif_carrier_off(phydev->attached_dev);
> }
>
> phydev->adjust_link(phydev->attached_dev);
> @@ -938,7 +940,8 @@ void phy_state_machine(struct work_struct *work)
> case PHY_HALTED:
> if (phydev->link) {
> phydev->link = 0;
> - netif_carrier_off(phydev->attached_dev);
> + if (!phydev->no_auto_carrier_off)
> + netif_carrier_off(phydev->attached_dev);
> phydev->adjust_link(phydev->attached_dev);
> do_suspend = true;
> }
> diff --git a/include/linux/phy.h b/include/linux/phy.h
> index 05fde31..276ab8a 100644
> --- a/include/linux/phy.h
> +++ b/include/linux/phy.h
> @@ -377,6 +377,7 @@ struct phy_device {
> bool is_pseudo_fixed_link;
> bool has_fixups;
> bool suspended;
> + bool no_auto_carrier_off;
>
> enum phy_state state;
>
>
--
Florian
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2015-11-24 18:43 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-11-22 8:40 [RFC 1/8] Documentation: DT: net: add docs for ralink/mediatek SoC ethernet binding John Crispin
2015-11-22 8:40 ` [RFC 2/8] net-next: phy: dont auto handle carrier state when multiple phys are attached John Crispin
2015-11-24 18:42 ` Florian Fainelli
2015-11-22 8:40 ` [RFC 3/8] net-next: ralink: add the drivers core files John Crispin
2015-11-22 8:40 ` [RFC 4/8] net-next: ralink: add support for rt2880 John Crispin
2015-11-22 8:40 ` [RFC 5/8] net-next: ralink: add support for rt3050 family John Crispin
2015-11-22 16:36 ` Andrew Lunn
2015-11-22 19:06 ` John Crispin
2015-11-22 23:16 ` Andrew Lunn
2015-11-23 6:47 ` John Crispin
2015-11-22 8:40 ` [RFC 6/8] net-next: ralink: add support for rt3883 John Crispin
2015-11-22 8:40 ` [RFC 7/8] net-next: ralink: add support for mt7620 family John Crispin
2015-11-22 8:40 ` [RFC 8/8] net-next: ralink: add Kconfig and Makefile John Crispin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.