[PATCH 1/4] ARM: mxs: dts: Add SSP2 SD mux

[PATCH 1/4] ARM: mxs: dts: Add SSP2 SD mux

[Marek Vasut]

From: Marek Vasut <marek.vasut@gmail.com>

Add pinmux configuration for SSP2 port in SD mode, both for
the 4-bit and 8-bit case.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
---
 arch/arm/boot/dts/imx23.dtsi | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi
index 302d116..c70ebef 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/imx23.dtsi
@@ -249,6 +249,40 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				mmc1_4bit_pins_a: mmc1-4bit at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_GPMI_D00__SSP2_DATA0
+						MX23_PAD_GPMI_D01__SSP2_DATA1
+						MX23_PAD_GPMI_D02__SSP2_DATA2
+						MX23_PAD_GPMI_D03__SSP2_DATA3
+						MX23_PAD_GPMI_RDY1__SSP2_CMD
+						MX23_PAD_GPMI_WRN__SSP2_SCK
+					>;
+					fsl,drive-strength = <MXS_DRIVE_8mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_ENABLE>;
+				};
+
+				mmc1_8bit_pins_a: mmc1-8bit at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_GPMI_D00__SSP2_DATA0
+						MX23_PAD_GPMI_D01__SSP2_DATA1
+						MX23_PAD_GPMI_D02__SSP2_DATA2
+						MX23_PAD_GPMI_D03__SSP2_DATA3
+						MX23_PAD_GPMI_D04__SSP2_DATA4
+						MX23_PAD_GPMI_D05__SSP2_DATA5
+						MX23_PAD_GPMI_D06__SSP2_DATA6
+						MX23_PAD_GPMI_D07__SSP2_DATA7
+						MX23_PAD_GPMI_RDY1__SSP2_CMD
+						MX23_PAD_GPMI_WRN__SSP2_SCK
+					>;
+					fsl,drive-strength = <MXS_DRIVE_8mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_ENABLE>;
+				};
+
 				pwm2_pins_a: pwm2 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
-- 
2.7.0

[PATCH 2/4] ARM: mxs: dts: Add AUART2 pinmux

[Marek Vasut]

From: Marek Vasut <marek.vasut@gmail.com>

Add 2-pin pinmux settings for AUART2.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
---
 arch/arm/boot/dts/imx23.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi
index c70ebef..0c9a357e 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/imx23.dtsi
@@ -171,6 +171,17 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				auart1_2pins_a: auart1-2pins at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_GPMI_D14__AUART2_RX
+						MX23_PAD_GPMI_D15__AUART2_TX
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				gpmi_pins_a: gpmi-nand at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
-- 
2.7.0

[PATCH V2 3/4] ARM: mxs: dts: Add Creative X-Fi3 support

[Marek Vasut]

From: Marek Vasut <marek.vasut@gmail.com>

Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
---
V2: - Fix the button nodes to not generate possible DT warning
    - Drop the address part from the license
---
 arch/arm/boot/dts/Makefile       |   1 +
 arch/arm/boot/dts/imx23-xfi3.dts | 183 +++++++++++++++++++++++++++++++++++++++
 2 files changed, 184 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx23-xfi3.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8f9f1c2..7a79d37 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -417,6 +417,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-evk.dtb \
 	imx23-olinuxino.dtb \
 	imx23-stmp378x_devb.dtb \
+	imx23-xfi3.dtb \
 	imx28-apf28.dtb \
 	imx28-apf28dev.dtb \
 	imx28-apx4devkit.dtb \
diff --git a/arch/arm/boot/dts/imx23-xfi3.dts b/arch/arm/boot/dts/imx23-xfi3.dts
new file mode 100644
index 0000000..abf9457
--- /dev/null
+++ b/arch/arm/boot/dts/imx23-xfi3.dts
@@ -0,0 +1,183 @@
+/*
+ * Copyright (C) 2013-2016 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx23.dtsi"
+
+/ {
+	model = "Creative ZEN X-Fi3";
+	compatible = "creative,x-fi3", "fsl,imx23";
+
+	memory {
+		reg = <0x40000000 0x04000000>;
+	};
+
+	apb at 80000000 {
+		apbh at 80000000 {
+			ssp0: ssp at 80010000 {
+				compatible = "fsl,imx23-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+				bus-width = <4>;
+				vmmc-supply = <&reg_vddio_sd0>;
+				cd-inverted;
+				status = "okay";
+			};
+
+			ssp1: ssp at 80034000 {
+				compatible = "fsl,imx23-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc1_4bit_pins_a>;
+				bus-width = <4>;
+				non-removable;
+				status = "okay";
+			};
+
+			pinctrl at 80018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&hog_pins_a>;
+
+				hog_pins_a: hog at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_GPMI_D07__GPIO_0_7
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				key_pins_a: keys at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_ROTARYA__GPIO_2_7
+						MX23_PAD_ROTARYB__GPIO_2_8
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+			};
+		};
+
+		apbx at 80040000 {
+			i2c: i2c at 80058000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c_pins_a>;
+				status = "okay";
+			};
+
+			pwm: pwm at 80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm2_pins_a>;
+				status = "okay";
+			};
+
+			duart: serial at 80070000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&duart_pins_a>;
+				status = "okay";
+			};
+
+			auart1: serial at 8006e000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&auart1_2pins_a>;
+				status = "okay";
+			};
+
+			usbphy0: usbphy at 8007c000 {
+				status = "okay";
+			};
+
+			lradc at 80050000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb at 80080000 {
+		usb0: usb at 80080000 {
+			dr_mode = "peripheral";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_vddio_sd0: vddio-sd0 {
+			compatible = "regulator-fixed";
+			regulator-name = "vddio-sd0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio0 7 0>;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 2 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_pins_a>;
+
+		voldown {
+			label = "volume-down";
+			linux,code = <114>;
+			gpios = <&gpio2 7 0>;
+			debounce-interval = <20>;
+		};
+
+		volup {
+			label = "volume-up";
+			linux,code = <115>;
+			gpios = <&gpio2 8 0>;
+			debounce-interval = <20>;
+		};
+	};
+};
-- 
2.7.0

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Marek Vasut]

From: Marek Vasut <marek.vasut@gmail.com>

Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
---
V2: - Drop the address part from the license
---
 arch/arm/boot/dts/Makefile        |   1 +
 arch/arm/boot/dts/imx23-sansa.dts | 211 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 212 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx23-sansa.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7a79d37..eaa8048 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -416,6 +416,7 @@ dtb-$(CONFIG_SOC_VF610) += \
 dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-evk.dtb \
 	imx23-olinuxino.dtb \
+	imx23-sansa.dtb \
 	imx23-stmp378x_devb.dtb \
 	imx23-xfi3.dtb \
 	imx28-apf28.dtb \
diff --git a/arch/arm/boot/dts/imx23-sansa.dts b/arch/arm/boot/dts/imx23-sansa.dts
new file mode 100644
index 0000000..c7b0ff4
--- /dev/null
+++ b/arch/arm/boot/dts/imx23-sansa.dts
@@ -0,0 +1,211 @@
+/*
+ * Copyright (C) 2013-2016 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx23.dtsi"
+
+/ {
+	model = "SanDisk Sansa Fuze+";
+	compatible = "sandisk,sansa_fuze_plus", "fsl,imx23";
+
+	memory {
+		reg = <0x40000000 0x04000000>;
+	};
+
+	apb at 80000000 {
+		apbh at 80000000 {
+			ssp0: ssp at 80010000 {
+				compatible = "fsl,imx23-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+				bus-width = <4>;
+				vmmc-supply = <&reg_vddio_sd0>;
+				cd-inverted;
+				status = "okay";
+			};
+
+			ssp1: ssp at 80034000 {
+				compatible = "fsl,imx23-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc1_8bit_pins_a>;
+				bus-width = <8>;
+				vmmc-supply = <&reg_vddio_sd1>;
+				non-removable;
+				status = "okay";
+			};
+
+			pinctrl at 80018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&hog_pins_a>;
+
+				hog_pins_a: hog at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_GPMI_D08__GPIO_0_8
+						MX23_PAD_PWM3__GPIO_1_29
+						MX23_PAD_AUART1_RTS__GPIO_0_27
+						MX23_PAD_AUART1_CTS__GPIO_0_26
+						MX23_PAD_I2C_SCL__I2C_SCL
+						MX23_PAD_I2C_SDA__I2C_SDA
+						MX23_PAD_LCD_DOTCK__GPIO_1_22
+						MX23_PAD_LCD_HSYNC__GPIO_1_24
+						MX23_PAD_PWM3__GPIO_1_29
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+		};
+
+		apbx at 80040000 {
+			pwm: pwm at 80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm2_pins_a>;
+				status = "okay";
+			};
+
+			duart: serial at 80070000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&duart_pins_a>;
+				status = "okay";
+			};
+
+			usbphy0: usbphy at 8007c000 {
+				status = "okay";
+			};
+
+			lradc at 80050000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb at 80080000 {
+		usb0: usb at 80080000 {
+			dr_mode = "peripheral";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_vddio_sd0: vddio-sd0 {
+			compatible = "regulator-fixed";
+			regulator-name = "vddio-sd0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio0 8 0>;
+		};
+
+		reg_vddio_sd1: vddio-sd1 {
+			compatible = "regulator-fixed";
+			regulator-name = "vddio-sd1";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio1 29 0>;
+		};
+
+		reg_vdd_touchpad: vdd-touchpad0 {
+			compatible = "regulator-fixed";
+			regulator-name = "vdd-touchpad0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio0 26 0>;
+			regulator-always-on;
+			enable-active-low;
+		};
+
+		reg_vdd_tuner: vdd-tuner0 {
+			compatible = "regulator-fixed";
+			regulator-name = "vdd-tuner0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio0 29 0>;
+			regulator-always-on;
+			enable-active-low;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 2 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	i2c at 0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "i2c-gpio";
+		gpios = <
+			&gpio1 24 0		/* SDA */
+			&gpio1 22 0		/* SCL */
+		>;
+		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+	};
+
+	i2c at 1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "i2c-gpio";
+		gpios = <
+			&gpio0 31 0		/* SDA */
+			&gpio0 30 0		/* SCL */
+		>;
+		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+
+		touch: touch at 20 {
+			compatible = "synaptics,synaptics_i2c";
+			reg = <0x20>;
+		};
+
+		eeprom: eeprom at 50 {
+			compatible = "atmel,24c64";
+			reg = <0x50>;
+			pagesize = <32>;
+		};
+	};
+
+};
-- 
2.7.0

[PATCH V2 3/4] ARM: mxs: dts: Add Creative X-Fi3 support

[Stefan Wahren]

Am 08.05.2016 um 22:50 schrieb Marek Vasut:
> From: Marek Vasut <marek.vasut@gmail.com>
>
> Add support for this small MP3 player based on STMP3780 (rev.4).
> Currently supported is both external microSD and internal SD-NAND
> bridge, PWM and USB gadget.
>
> Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Shawn Guo <shawnguo@kernel.org>
> ---
> V2: - Fix the button nodes to not generate possible DT warning
>     - Drop the address part from the license
> ---

Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>

Thanks

[PATCH V2 3/4] ARM: mxs: dts: Add Creative X-Fi3 support

[Shawn Guo]

On Sun, May 08, 2016 at 10:50:20PM +0200, Marek Vasut wrote:
> +	regulators {
> +		compatible = "simple-bus";
> +
> +		reg_vddio_sd0: vddio-sd0 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vddio-sd0";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio0 7 0>;
> +		};
> +	};

For new dts, we suggest put fixed regulator node directly under root in
the following naming scheme:

	reg_xxx: regulator-xxx {
		...
	};

Also, the order of subject prefix is like ARM: dts: mxs: ...

Shawn

[PATCH V2 3/4] ARM: mxs: dts: Add Creative X-Fi3 support

[Marek Vasut]

On 06/06/2016 10:45 AM, Shawn Guo wrote:
> On Sun, May 08, 2016 at 10:50:20PM +0200, Marek Vasut wrote:
>> +	regulators {
>> +		compatible = "simple-bus";
>> +
>> +		reg_vddio_sd0: vddio-sd0 {
>> +			compatible = "regulator-fixed";
>> +			regulator-name = "vddio-sd0";
>> +			regulator-min-microvolt = <3300000>;
>> +			regulator-max-microvolt = <3300000>;
>> +			gpio = <&gpio0 7 0>;
>> +		};
>> +	};
> 
> For new dts, we suggest put fixed regulator node directly under root in
> the following naming scheme:
> 
> 	reg_xxx: regulator-xxx {
> 		...
> 	};
> 
> Also, the order of subject prefix is like ARM: dts: mxs: ...

I see, can you do this trivial fix while applying ?

Thanks

-- 
Best regards,
Marek Vasut

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Shawn Guo]

On Sun, May 08, 2016 at 10:50:21PM +0200, Marek Vasut wrote:
> +	regulators {
> +		compatible = "simple-bus";
> +
> +		reg_vddio_sd0: vddio-sd0 {

Put fixed regulator nodes directly under root with suggested naming
scheme.

> +			compatible = "regulator-fixed";
> +			regulator-name = "vddio-sd0";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio0 8 0>;
> +		};
> +
> +		reg_vddio_sd1: vddio-sd1 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vddio-sd1";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio1 29 0>;
> +		};
> +
> +		reg_vdd_touchpad: vdd-touchpad0 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vdd-touchpad0";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio0 26 0>;
> +			regulator-always-on;
> +			enable-active-low;
> +		};
> +
> +		reg_vdd_tuner: vdd-tuner0 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vdd-tuner0";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio0 29 0>;
> +			regulator-always-on;
> +			enable-active-low;
> +		};
> +	};
> +
> +	backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm 2 5000000>;
> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> +		default-brightness-level = <6>;
> +	};
> +
> +	i2c at 0 {

The @unit-address should be used for nodes with 'reg' property.

Shawn

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "i2c-gpio";
> +		gpios = <
> +			&gpio1 24 0		/* SDA */
> +			&gpio1 22 0		/* SCL */
> +		>;
> +		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
> +	};
> +
> +	i2c at 1 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "i2c-gpio";
> +		gpios = <
> +			&gpio0 31 0		/* SDA */
> +			&gpio0 30 0		/* SCL */
> +		>;
> +		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
> +
> +		touch: touch at 20 {
> +			compatible = "synaptics,synaptics_i2c";
> +			reg = <0x20>;
> +		};
> +
> +		eeprom: eeprom at 50 {
> +			compatible = "atmel,24c64";
> +			reg = <0x50>;
> +			pagesize = <32>;
> +		};
> +	};
> +
> +};
> -- 
> 2.7.0
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Marek Vasut]

On 06/09/2016 03:21 AM, Shawn Guo wrote:
> On Sun, May 08, 2016 at 10:50:21PM +0200, Marek Vasut wrote:
>> +	regulators {
>> +		compatible = "simple-bus";
>> +
>> +		reg_vddio_sd0: vddio-sd0 {
> 
> Put fixed regulator nodes directly under root with suggested naming
> scheme.
> 
>> +			compatible = "regulator-fixed";
>> +			regulator-name = "vddio-sd0";
>> +			regulator-min-microvolt = <3300000>;
>> +			regulator-max-microvolt = <3300000>;
>> +			gpio = <&gpio0 8 0>;
>> +		};
>> +
>> +		reg_vddio_sd1: vddio-sd1 {
>> +			compatible = "regulator-fixed";
>> +			regulator-name = "vddio-sd1";
>> +			regulator-min-microvolt = <3300000>;
>> +			regulator-max-microvolt = <3300000>;
>> +			gpio = <&gpio1 29 0>;
>> +		};
>> +
>> +		reg_vdd_touchpad: vdd-touchpad0 {
>> +			compatible = "regulator-fixed";
>> +			regulator-name = "vdd-touchpad0";
>> +			regulator-min-microvolt = <3300000>;
>> +			regulator-max-microvolt = <3300000>;
>> +			gpio = <&gpio0 26 0>;
>> +			regulator-always-on;
>> +			enable-active-low;
>> +		};
>> +
>> +		reg_vdd_tuner: vdd-tuner0 {
>> +			compatible = "regulator-fixed";
>> +			regulator-name = "vdd-tuner0";
>> +			regulator-min-microvolt = <3300000>;
>> +			regulator-max-microvolt = <3300000>;
>> +			gpio = <&gpio0 29 0>;
>> +			regulator-always-on;
>> +			enable-active-low;
>> +		};
>> +	};
>> +
>> +	backlight {
>> +		compatible = "pwm-backlight";
>> +		pwms = <&pwm 2 5000000>;
>> +		brightness-levels = <0 4 8 16 32 64 128 255>;
>> +		default-brightness-level = <6>;
>> +	};
>> +
>> +	i2c at 0 {
> 
> The @unit-address should be used for nodes with 'reg' property.

Can you please do such minor fixes when applying or do you expect a resend ?

> Shawn
> 
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		compatible = "i2c-gpio";
>> +		gpios = <
>> +			&gpio1 24 0		/* SDA */
>> +			&gpio1 22 0		/* SCL */
>> +		>;
>> +		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
>> +	};
>> +
>> +	i2c at 1 {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		compatible = "i2c-gpio";
>> +		gpios = <
>> +			&gpio0 31 0		/* SDA */
>> +			&gpio0 30 0		/* SCL */
>> +		>;
>> +		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
>> +
>> +		touch: touch at 20 {
>> +			compatible = "synaptics,synaptics_i2c";
>> +			reg = <0x20>;
>> +		};
>> +
>> +		eeprom: eeprom at 50 {
>> +			compatible = "atmel,24c64";
>> +			reg = <0x50>;
>> +			pagesize = <32>;
>> +		};
>> +	};
>> +
>> +};
>> -- 
>> 2.7.0
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel


-- 
Best regards,
Marek Vasut

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Shawn Guo]

On Thu, Jun 09, 2016 at 03:30:16AM +0200, Marek Vasut wrote:
> On 06/09/2016 03:21 AM, Shawn Guo wrote:
> > On Sun, May 08, 2016 at 10:50:21PM +0200, Marek Vasut wrote:
> >> +	regulators {
> >> +		compatible = "simple-bus";
> >> +
> >> +		reg_vddio_sd0: vddio-sd0 {
> > 
> > Put fixed regulator nodes directly under root with suggested naming
> > scheme.
> > 
> >> +			compatible = "regulator-fixed";
> >> +			regulator-name = "vddio-sd0";
> >> +			regulator-min-microvolt = <3300000>;
> >> +			regulator-max-microvolt = <3300000>;
> >> +			gpio = <&gpio0 8 0>;
> >> +		};
> >> +
> >> +		reg_vddio_sd1: vddio-sd1 {
> >> +			compatible = "regulator-fixed";
> >> +			regulator-name = "vddio-sd1";
> >> +			regulator-min-microvolt = <3300000>;
> >> +			regulator-max-microvolt = <3300000>;
> >> +			gpio = <&gpio1 29 0>;
> >> +		};
> >> +
> >> +		reg_vdd_touchpad: vdd-touchpad0 {
> >> +			compatible = "regulator-fixed";
> >> +			regulator-name = "vdd-touchpad0";
> >> +			regulator-min-microvolt = <3300000>;
> >> +			regulator-max-microvolt = <3300000>;
> >> +			gpio = <&gpio0 26 0>;
> >> +			regulator-always-on;
> >> +			enable-active-low;
> >> +		};
> >> +
> >> +		reg_vdd_tuner: vdd-tuner0 {
> >> +			compatible = "regulator-fixed";
> >> +			regulator-name = "vdd-tuner0";
> >> +			regulator-min-microvolt = <3300000>;
> >> +			regulator-max-microvolt = <3300000>;
> >> +			gpio = <&gpio0 29 0>;
> >> +			regulator-always-on;
> >> +			enable-active-low;
> >> +		};
> >> +	};
> >> +
> >> +	backlight {
> >> +		compatible = "pwm-backlight";
> >> +		pwms = <&pwm 2 5000000>;
> >> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> >> +		default-brightness-level = <6>;
> >> +	};
> >> +
> >> +	i2c at 0 {
> > 
> > The @unit-address should be used for nodes with 'reg' property.
> 
> Can you please do such minor fixes when applying or do you expect a resend ?

Such minor fixes are just too many to be fixed by myself.  Please
resend.

Shawn

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Marek Vasut]

On 06/09/2016 04:13 AM, Shawn Guo wrote:
> On Thu, Jun 09, 2016 at 03:30:16AM +0200, Marek Vasut wrote:
>> On 06/09/2016 03:21 AM, Shawn Guo wrote:
>>> On Sun, May 08, 2016 at 10:50:21PM +0200, Marek Vasut wrote:
>>>> +	regulators {
>>>> +		compatible = "simple-bus";
>>>> +
>>>> +		reg_vddio_sd0: vddio-sd0 {
>>>
>>> Put fixed regulator nodes directly under root with suggested naming
>>> scheme.
>>>
>>>> +			compatible = "regulator-fixed";
>>>> +			regulator-name = "vddio-sd0";
>>>> +			regulator-min-microvolt = <3300000>;
>>>> +			regulator-max-microvolt = <3300000>;
>>>> +			gpio = <&gpio0 8 0>;
>>>> +		};
>>>> +
>>>> +		reg_vddio_sd1: vddio-sd1 {
>>>> +			compatible = "regulator-fixed";
>>>> +			regulator-name = "vddio-sd1";
>>>> +			regulator-min-microvolt = <3300000>;
>>>> +			regulator-max-microvolt = <3300000>;
>>>> +			gpio = <&gpio1 29 0>;
>>>> +		};
>>>> +
>>>> +		reg_vdd_touchpad: vdd-touchpad0 {
>>>> +			compatible = "regulator-fixed";
>>>> +			regulator-name = "vdd-touchpad0";
>>>> +			regulator-min-microvolt = <3300000>;
>>>> +			regulator-max-microvolt = <3300000>;
>>>> +			gpio = <&gpio0 26 0>;
>>>> +			regulator-always-on;
>>>> +			enable-active-low;
>>>> +		};
>>>> +
>>>> +		reg_vdd_tuner: vdd-tuner0 {
>>>> +			compatible = "regulator-fixed";
>>>> +			regulator-name = "vdd-tuner0";
>>>> +			regulator-min-microvolt = <3300000>;
>>>> +			regulator-max-microvolt = <3300000>;
>>>> +			gpio = <&gpio0 29 0>;
>>>> +			regulator-always-on;
>>>> +			enable-active-low;
>>>> +		};
>>>> +	};
>>>> +
>>>> +	backlight {
>>>> +		compatible = "pwm-backlight";
>>>> +		pwms = <&pwm 2 5000000>;
>>>> +		brightness-levels = <0 4 8 16 32 64 128 255>;
>>>> +		default-brightness-level = <6>;
>>>> +	};
>>>> +
>>>> +	i2c at 0 {
>>>
>>> The @unit-address should be used for nodes with 'reg' property.
>>
>> Can you please do such minor fixes when applying or do you expect a resend ?
> 
> Such minor fixes are just too many to be fixed by myself.  Please
> resend.

I see. Would you be able to review them in less than one month please ?
It is extremely demotivating to wait over a month only to get a review
with a few nitpicks and request to resend.

-- 
Best regards,
Marek Vasut

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Shawn Guo]

On Thu, Jun 09, 2016 at 04:18:11AM +0200, Marek Vasut wrote:
> I see. Would you be able to review them in less than one month please ?
> It is extremely demotivating to wait over a month only to get a review
> with a few nitpicks and request to resend.

Sure, that's really something I'm trying to avoid.  I definitely won't
let the review delay get patches miss the merge window.  So one month
should be the worst case when my paid job get me so busy.

BTW, today is the public holiday in China.

Shawn

[PATCH V2 4/4] ARM: mxs: dts: Add SanDisk Sansa Fuze+ support

[Marek Vasut]

On 06/09/2016 04:42 AM, Shawn Guo wrote:
> On Thu, Jun 09, 2016 at 04:18:11AM +0200, Marek Vasut wrote:
>> I see. Would you be able to review them in less than one month please ?
>> It is extremely demotivating to wait over a month only to get a review
>> with a few nitpicks and request to resend.
> 
> Sure, that's really something I'm trying to avoid.  I definitely won't
> let the review delay get patches miss the merge window.  So one month
> should be the worst case when my paid job get me so busy.

I see, thanks.

> BTW, today is the public holiday in China.
> 
> Shawn
> 


-- 
Best regards,
Marek Vasut