* [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
@ 2016-06-10 9:34 ` Srinivas Kandagatla
0 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 9:34 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, David Brown, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-soc-u79uwXL29TY76Z2rM5mHXA, Srinivas Kandagatla
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 2 +-
.../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
.../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
.../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
5 files changed, 402 insertions(+), 402 deletions(-)
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 488a943..66e182c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -573,7 +573,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \
dtb-$(CONFIG_ARCH_OXNAS) += \
wd-mbwe.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-apq8064-arrow-db600c.dtb \
+ qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
deleted file mode 100644
index a3efb97..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
+++ /dev/null
@@ -1,52 +0,0 @@
-&tlmm_pinmux {
- card_detect: card-detect {
- mux {
- pins = "gpio26";
- function = "gpio";
- bias-disable;
- };
- };
-
- pcie_pins: pcie-pinmux {
- mux {
- pins = "gpio27";
- function = "gpio";
- };
- conf {
- pins = "gpio27";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- user_leds: user-leds {
- mux {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- };
-
- conf {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- output-low;
- };
- };
-
- magneto_pins: magneto-pins {
- mux {
- pins = "gpio31", "gpio48";
- function = "gpio";
- bias-disable;
- };
- };
-};
-
-&pm8921_mpps {
- mpp_leds: mpp-leds {
- pinconf {
- pins = "mpp7", "mpp8";
- function = "digital";
- output-low;
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
deleted file mode 100644
index e01b27e..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
+++ /dev/null
@@ -1,349 +0,0 @@
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-db600c-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Arrow Electronics, APQ8064 DB600c";
- compatible = "arrow,db600c", "qcom,apq8064";
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi1_serial;
- i2c0 = &gsbi2_i2c;
- i2c1 = &gsbi3_i2c;
- i2c2 = &gsbi4_i2c;
- i2c3 = &gsbi7_i2c;
- spi0 = &gsbi5_spi;
- };
-
- regulators {
- compatible = "simple-bus";
- vph: regulator-fixed@1 {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <4500000>;
- regulator-name = "VPH";
- regulator-type = "voltage";
- regulator-boot-on;
- };
-
- /* on board fixed 3.3v supply */
- vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- };
-
- soc {
- rpm@108000 {
- regulators {
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_s5-supply = <&vph>;
- vdd_s6-supply = <&vph>;
- vdd_s7-supply = <&vph>;
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
- vdd_l3_l15_l17-supply = <&vph>;
- vdd_l4_l14-supply = <&vph>;
- vdd_l5_l8_l16-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l9_l11-supply = <&vph>;
- vdd_l10_l22-supply = <&vph>;
- vdd_l21_l23_l29-supply = <&vph>;
- vdd_l24-supply = <&pm8921_s1>;
- vdd_l25-supply = <&pm8921_s1>;
- vdd_l26-supply = <&pm8921_s7>;
- vdd_l27-supply = <&pm8921_s7>;
- vdd_l28-supply = <&pm8921_s7>;
- vin_lvs1_3_6-supply = <&pm8921_s4>;
- vin_lvs2-supply = <&pm8921_s1>;
- vin_lvs4_5_7-supply = <&pm8921_s4>;
-
- s1 {
- regulator-always-on;
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- };
-
- s3 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <4800000>;
- };
-
- s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s7 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <3200000>;
- };
-
- l3 {
- regulator-min-microvolt = <3050000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
-
- l4 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
-
- l5 {
- regulator-min-microvolt = <2750000>;
- regulator-max-microvolt = <3000000>;
- bias-pull-down;
- regulator-boot-on;
- regulator-always-on;
- };
-
- l6 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- bias-pull-down;
- };
-
- l23 {
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- bias-pull-down;
- };
-
- lvs6 {
- bias-pull-down;
- };
-
- lvs7 {
- bias-pull-down;
- };
- };
- };
-
- gsbi@12440000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- serial@12450000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi1_uart_4pins>;
- };
- };
-
- gsbi@12480000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@124a0000 {
- /* On Low speed expansion and Sensors */
- label = "LS-I2C0";
- status = "okay";
- lis3mdl_mag@1e {
- compatible = "st,lis3mdl-magn";
- reg = <0x1e>;
- vdd-supply = <&vcc3v3>;
- vddio-supply = <&pm8921_s4>;
- pinctrl-names = "default";
- pinctrl-0 = <&magneto_pins>;
- interrupt-parent = <&tlmm_pinmux>;
-
- st,drdy-int-pin = <2>;
- interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
- <31 IRQ_TYPE_EDGE_RISING>; /* INT */
- };
- };
- };
-
- gsbi@16200000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16280000 {
- /* On Low speed expansion */
- status = "okay";
- label = "LS-I2C1";
- clock-frequency = <200000>;
- eeprom@52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <64>;
- };
- };
- };
-
- gsbi@16300000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16380000 {
- /* On High speed expansion */
- label = "HS-CAM-I2C3";
- status = "okay";
- };
- };
-
- gsbi@1a200000 {
- status = "okay";
- spi@1a280000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
- };
-
- /* DEBUG UART */
- gsbi@16600000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
- serial@16640000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi7_uart_2pins>;
- };
-
- i2c@16680000 {
- /* On High speed expansion */
- status = "okay";
- label = "HS-CAM-I2C2";
- };
- };
-
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
- compatible = "gpio-leds";
-
- user-led0 {
- label = "user0-led";
- gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- user-led1 {
- label = "user1-led";
- gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- user-led2 {
- label = "user2-led";
- gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- user-led3 {
- label = "user3-led";
- gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- };
-
- wifi-led {
- label = "WiFi-led";
- gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- bt-led {
- label = "BT-led";
- gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- pci@1b500000 {
- status = "okay";
- vdda-supply = <&pm8921_s3>;
- vdda_phy-supply = <&pm8921_lvs6>;
- vdda_refclk-supply = <&vcc3v3>;
- pinctrl-0 = <&pcie_pins>;
- pinctrl-names = "default";
- perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- target-supply = <&pm8921_lvs7>;
- };
-
- /* OTG */
- phy@12500000 {
- status = "okay";
- dr_mode = "peripheral";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l4>;
- };
-
- phy@12520000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- phy@12530000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- gadget@12500000 {
- status = "okay";
- };
-
- /* OTG */
- usb@12500000 {
- status = "okay";
- };
-
- usb@12520000 {
- status = "okay";
- };
-
- usb@12530000 {
- status = "okay";
- };
-
- amba {
- /* eMMC */
- sdcc@12400000 {
- status = "okay";
- vmmc-supply = <&pm8921_l5>;
- vqmmc-supply = <&pm8921_s4>;
- };
-
- /* External micro SD card */
- sdcc@12180000 {
- status = "okay";
- vmmc-supply = <&pm8921_l6>;
- pinctrl-names = "default";
- pinctrl-0 = <&card_detect>;
- cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
new file mode 100644
index 0000000..a3efb97
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
@@ -0,0 +1,52 @@
+&tlmm_pinmux {
+ card_detect: card-detect {
+ mux {
+ pins = "gpio26";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ pcie_pins: pcie-pinmux {
+ mux {
+ pins = "gpio27";
+ function = "gpio";
+ };
+ conf {
+ pins = "gpio27";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ user_leds: user-leds {
+ mux {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ };
+
+ conf {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ output-low;
+ };
+ };
+
+ magneto_pins: magneto-pins {
+ mux {
+ pins = "gpio31", "gpio48";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+};
+
+&pm8921_mpps {
+ mpp_leds: mpp-leds {
+ pinconf {
+ pins = "mpp7", "mpp8";
+ function = "digital";
+ output-low;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
new file mode 100644
index 0000000..7df0108
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -0,0 +1,349 @@
+#include "qcom-apq8064-v2.0.dtsi"
+#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Arrow Electronics, APQ8064 SD_600eval";
+ compatible = "arrow,sd_600eval", "qcom,apq8064";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi1_serial;
+ i2c0 = &gsbi2_i2c;
+ i2c1 = &gsbi3_i2c;
+ i2c2 = &gsbi4_i2c;
+ i2c3 = &gsbi7_i2c;
+ spi0 = &gsbi5_spi;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ vph: regulator-fixed@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <4500000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ };
+
+ /* on board fixed 3.3v supply */
+ vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ };
+
+ soc {
+ rpm@108000 {
+ regulators {
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_s5-supply = <&vph>;
+ vdd_s6-supply = <&vph>;
+ vdd_s7-supply = <&vph>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l3_l15_l17-supply = <&vph>;
+ vdd_l4_l14-supply = <&vph>;
+ vdd_l5_l8_l16-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l9_l11-supply = <&vph>;
+ vdd_l10_l22-supply = <&vph>;
+ vdd_l21_l23_l29-supply = <&vph>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s1>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ l5 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ l23 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ lvs6 {
+ bias-pull-down;
+ };
+
+ lvs7 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ gsbi@12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ serial@12450000 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi1_uart_4pins>;
+ };
+ };
+
+ gsbi@12480000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@124a0000 {
+ /* On Low speed expansion and Sensors */
+ label = "LS-I2C0";
+ status = "okay";
+ lis3mdl_mag@1e {
+ compatible = "st,lis3mdl-magn";
+ reg = <0x1e>;
+ vdd-supply = <&vcc3v3>;
+ vddio-supply = <&pm8921_s4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&magneto_pins>;
+ interrupt-parent = <&tlmm_pinmux>;
+
+ st,drdy-int-pin = <2>;
+ interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
+ <31 IRQ_TYPE_EDGE_RISING>; /* INT */
+ };
+ };
+ };
+
+ gsbi@16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16280000 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+ clock-frequency = <200000>;
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <64>;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16380000 {
+ /* On High speed expansion */
+ label = "HS-CAM-I2C3";
+ status = "okay";
+ };
+ };
+
+ gsbi@1a200000 {
+ status = "okay";
+ spi@1a280000 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+ };
+ };
+
+ /* DEBUG UART */
+ gsbi@16600000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16640000 {
+ label = "LS-UART0";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi7_uart_2pins>;
+ };
+
+ i2c@16680000 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-CAM-I2C2";
+ };
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+ compatible = "gpio-leds";
+
+ user-led0 {
+ label = "user0-led";
+ gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ user-led1 {
+ label = "user1-led";
+ gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ user-led2 {
+ label = "user2-led";
+ gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ user-led3 {
+ label = "user3-led";
+ gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ };
+
+ wifi-led {
+ label = "WiFi-led";
+ gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ bt-led {
+ label = "BT-led";
+ gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ pci@1b500000 {
+ status = "okay";
+ vdda-supply = <&pm8921_s3>;
+ vdda_phy-supply = <&pm8921_lvs6>;
+ vdda_refclk-supply = <&vcc3v3>;
+ pinctrl-0 = <&pcie_pins>;
+ pinctrl-names = "default";
+ perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+ };
+
+ phy@1b400000 {
+ status = "okay";
+ };
+
+ sata@29000000 {
+ status = "okay";
+ target-supply = <&pm8921_lvs7>;
+ };
+
+ /* OTG */
+ phy@12500000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+
+ phy@12520000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ phy@12530000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ gadget@12500000 {
+ status = "okay";
+ };
+
+ /* OTG */
+ usb@12500000 {
+ status = "okay";
+ };
+
+ usb@12520000 {
+ status = "okay";
+ };
+
+ usb@12530000 {
+ status = "okay";
+ };
+
+ amba {
+ /* eMMC */
+ sdcc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
+ };
+
+ /* External micro SD card */
+ sdcc@12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&card_detect>;
+ cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
--
2.8.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
@ 2016-06-10 9:34 ` Srinivas Kandagatla
0 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 9:34 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, David Brown, devicetree, linux-arm-kernel,
linux-kernel, linux-arm-msm, linux-soc, Srinivas Kandagatla
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm/boot/dts/Makefile | 2 +-
.../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
.../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
.../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
5 files changed, 402 insertions(+), 402 deletions(-)
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 488a943..66e182c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -573,7 +573,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \
dtb-$(CONFIG_ARCH_OXNAS) += \
wd-mbwe.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-apq8064-arrow-db600c.dtb \
+ qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
deleted file mode 100644
index a3efb97..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
+++ /dev/null
@@ -1,52 +0,0 @@
-&tlmm_pinmux {
- card_detect: card-detect {
- mux {
- pins = "gpio26";
- function = "gpio";
- bias-disable;
- };
- };
-
- pcie_pins: pcie-pinmux {
- mux {
- pins = "gpio27";
- function = "gpio";
- };
- conf {
- pins = "gpio27";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- user_leds: user-leds {
- mux {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- };
-
- conf {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- output-low;
- };
- };
-
- magneto_pins: magneto-pins {
- mux {
- pins = "gpio31", "gpio48";
- function = "gpio";
- bias-disable;
- };
- };
-};
-
-&pm8921_mpps {
- mpp_leds: mpp-leds {
- pinconf {
- pins = "mpp7", "mpp8";
- function = "digital";
- output-low;
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
deleted file mode 100644
index e01b27e..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
+++ /dev/null
@@ -1,349 +0,0 @@
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-db600c-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Arrow Electronics, APQ8064 DB600c";
- compatible = "arrow,db600c", "qcom,apq8064";
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi1_serial;
- i2c0 = &gsbi2_i2c;
- i2c1 = &gsbi3_i2c;
- i2c2 = &gsbi4_i2c;
- i2c3 = &gsbi7_i2c;
- spi0 = &gsbi5_spi;
- };
-
- regulators {
- compatible = "simple-bus";
- vph: regulator-fixed@1 {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <4500000>;
- regulator-name = "VPH";
- regulator-type = "voltage";
- regulator-boot-on;
- };
-
- /* on board fixed 3.3v supply */
- vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- };
-
- soc {
- rpm@108000 {
- regulators {
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_s5-supply = <&vph>;
- vdd_s6-supply = <&vph>;
- vdd_s7-supply = <&vph>;
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
- vdd_l3_l15_l17-supply = <&vph>;
- vdd_l4_l14-supply = <&vph>;
- vdd_l5_l8_l16-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l9_l11-supply = <&vph>;
- vdd_l10_l22-supply = <&vph>;
- vdd_l21_l23_l29-supply = <&vph>;
- vdd_l24-supply = <&pm8921_s1>;
- vdd_l25-supply = <&pm8921_s1>;
- vdd_l26-supply = <&pm8921_s7>;
- vdd_l27-supply = <&pm8921_s7>;
- vdd_l28-supply = <&pm8921_s7>;
- vin_lvs1_3_6-supply = <&pm8921_s4>;
- vin_lvs2-supply = <&pm8921_s1>;
- vin_lvs4_5_7-supply = <&pm8921_s4>;
-
- s1 {
- regulator-always-on;
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- };
-
- s3 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <4800000>;
- };
-
- s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s7 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <3200000>;
- };
-
- l3 {
- regulator-min-microvolt = <3050000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
-
- l4 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
-
- l5 {
- regulator-min-microvolt = <2750000>;
- regulator-max-microvolt = <3000000>;
- bias-pull-down;
- regulator-boot-on;
- regulator-always-on;
- };
-
- l6 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- bias-pull-down;
- };
-
- l23 {
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- bias-pull-down;
- };
-
- lvs6 {
- bias-pull-down;
- };
-
- lvs7 {
- bias-pull-down;
- };
- };
- };
-
- gsbi@12440000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- serial@12450000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi1_uart_4pins>;
- };
- };
-
- gsbi@12480000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@124a0000 {
- /* On Low speed expansion and Sensors */
- label = "LS-I2C0";
- status = "okay";
- lis3mdl_mag@1e {
- compatible = "st,lis3mdl-magn";
- reg = <0x1e>;
- vdd-supply = <&vcc3v3>;
- vddio-supply = <&pm8921_s4>;
- pinctrl-names = "default";
- pinctrl-0 = <&magneto_pins>;
- interrupt-parent = <&tlmm_pinmux>;
-
- st,drdy-int-pin = <2>;
- interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
- <31 IRQ_TYPE_EDGE_RISING>; /* INT */
- };
- };
- };
-
- gsbi@16200000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16280000 {
- /* On Low speed expansion */
- status = "okay";
- label = "LS-I2C1";
- clock-frequency = <200000>;
- eeprom@52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <64>;
- };
- };
- };
-
- gsbi@16300000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16380000 {
- /* On High speed expansion */
- label = "HS-CAM-I2C3";
- status = "okay";
- };
- };
-
- gsbi@1a200000 {
- status = "okay";
- spi@1a280000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
- };
-
- /* DEBUG UART */
- gsbi@16600000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
- serial@16640000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi7_uart_2pins>;
- };
-
- i2c@16680000 {
- /* On High speed expansion */
- status = "okay";
- label = "HS-CAM-I2C2";
- };
- };
-
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
- compatible = "gpio-leds";
-
- user-led0 {
- label = "user0-led";
- gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- user-led1 {
- label = "user1-led";
- gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- user-led2 {
- label = "user2-led";
- gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- user-led3 {
- label = "user3-led";
- gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- };
-
- wifi-led {
- label = "WiFi-led";
- gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- bt-led {
- label = "BT-led";
- gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- pci@1b500000 {
- status = "okay";
- vdda-supply = <&pm8921_s3>;
- vdda_phy-supply = <&pm8921_lvs6>;
- vdda_refclk-supply = <&vcc3v3>;
- pinctrl-0 = <&pcie_pins>;
- pinctrl-names = "default";
- perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- target-supply = <&pm8921_lvs7>;
- };
-
- /* OTG */
- phy@12500000 {
- status = "okay";
- dr_mode = "peripheral";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l4>;
- };
-
- phy@12520000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- phy@12530000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- gadget@12500000 {
- status = "okay";
- };
-
- /* OTG */
- usb@12500000 {
- status = "okay";
- };
-
- usb@12520000 {
- status = "okay";
- };
-
- usb@12530000 {
- status = "okay";
- };
-
- amba {
- /* eMMC */
- sdcc@12400000 {
- status = "okay";
- vmmc-supply = <&pm8921_l5>;
- vqmmc-supply = <&pm8921_s4>;
- };
-
- /* External micro SD card */
- sdcc@12180000 {
- status = "okay";
- vmmc-supply = <&pm8921_l6>;
- pinctrl-names = "default";
- pinctrl-0 = <&card_detect>;
- cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
new file mode 100644
index 0000000..a3efb97
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
@@ -0,0 +1,52 @@
+&tlmm_pinmux {
+ card_detect: card-detect {
+ mux {
+ pins = "gpio26";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ pcie_pins: pcie-pinmux {
+ mux {
+ pins = "gpio27";
+ function = "gpio";
+ };
+ conf {
+ pins = "gpio27";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ user_leds: user-leds {
+ mux {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ };
+
+ conf {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ output-low;
+ };
+ };
+
+ magneto_pins: magneto-pins {
+ mux {
+ pins = "gpio31", "gpio48";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+};
+
+&pm8921_mpps {
+ mpp_leds: mpp-leds {
+ pinconf {
+ pins = "mpp7", "mpp8";
+ function = "digital";
+ output-low;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
new file mode 100644
index 0000000..7df0108
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -0,0 +1,349 @@
+#include "qcom-apq8064-v2.0.dtsi"
+#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Arrow Electronics, APQ8064 SD_600eval";
+ compatible = "arrow,sd_600eval", "qcom,apq8064";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi1_serial;
+ i2c0 = &gsbi2_i2c;
+ i2c1 = &gsbi3_i2c;
+ i2c2 = &gsbi4_i2c;
+ i2c3 = &gsbi7_i2c;
+ spi0 = &gsbi5_spi;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ vph: regulator-fixed@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <4500000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ };
+
+ /* on board fixed 3.3v supply */
+ vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ };
+
+ soc {
+ rpm@108000 {
+ regulators {
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_s5-supply = <&vph>;
+ vdd_s6-supply = <&vph>;
+ vdd_s7-supply = <&vph>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l3_l15_l17-supply = <&vph>;
+ vdd_l4_l14-supply = <&vph>;
+ vdd_l5_l8_l16-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l9_l11-supply = <&vph>;
+ vdd_l10_l22-supply = <&vph>;
+ vdd_l21_l23_l29-supply = <&vph>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s1>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ l5 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ l23 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ lvs6 {
+ bias-pull-down;
+ };
+
+ lvs7 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ gsbi@12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ serial@12450000 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi1_uart_4pins>;
+ };
+ };
+
+ gsbi@12480000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@124a0000 {
+ /* On Low speed expansion and Sensors */
+ label = "LS-I2C0";
+ status = "okay";
+ lis3mdl_mag@1e {
+ compatible = "st,lis3mdl-magn";
+ reg = <0x1e>;
+ vdd-supply = <&vcc3v3>;
+ vddio-supply = <&pm8921_s4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&magneto_pins>;
+ interrupt-parent = <&tlmm_pinmux>;
+
+ st,drdy-int-pin = <2>;
+ interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
+ <31 IRQ_TYPE_EDGE_RISING>; /* INT */
+ };
+ };
+ };
+
+ gsbi@16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16280000 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+ clock-frequency = <200000>;
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <64>;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c@16380000 {
+ /* On High speed expansion */
+ label = "HS-CAM-I2C3";
+ status = "okay";
+ };
+ };
+
+ gsbi@1a200000 {
+ status = "okay";
+ spi@1a280000 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+ };
+ };
+
+ /* DEBUG UART */
+ gsbi@16600000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial@16640000 {
+ label = "LS-UART0";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi7_uart_2pins>;
+ };
+
+ i2c@16680000 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-CAM-I2C2";
+ };
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+ compatible = "gpio-leds";
+
+ user-led0 {
+ label = "user0-led";
+ gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ user-led1 {
+ label = "user1-led";
+ gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ user-led2 {
+ label = "user2-led";
+ gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ user-led3 {
+ label = "user3-led";
+ gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ };
+
+ wifi-led {
+ label = "WiFi-led";
+ gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ bt-led {
+ label = "BT-led";
+ gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ pci@1b500000 {
+ status = "okay";
+ vdda-supply = <&pm8921_s3>;
+ vdda_phy-supply = <&pm8921_lvs6>;
+ vdda_refclk-supply = <&vcc3v3>;
+ pinctrl-0 = <&pcie_pins>;
+ pinctrl-names = "default";
+ perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+ };
+
+ phy@1b400000 {
+ status = "okay";
+ };
+
+ sata@29000000 {
+ status = "okay";
+ target-supply = <&pm8921_lvs7>;
+ };
+
+ /* OTG */
+ phy@12500000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+
+ phy@12520000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ phy@12530000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ gadget@12500000 {
+ status = "okay";
+ };
+
+ /* OTG */
+ usb@12500000 {
+ status = "okay";
+ };
+
+ usb@12520000 {
+ status = "okay";
+ };
+
+ usb@12530000 {
+ status = "okay";
+ };
+
+ amba {
+ /* eMMC */
+ sdcc@12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
+ };
+
+ /* External micro SD card */
+ sdcc@12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&card_detect>;
+ cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
--
2.8.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
@ 2016-06-10 9:34 ` Srinivas Kandagatla
0 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 9:34 UTC (permalink / raw)
To: linux-arm-kernel
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm/boot/dts/Makefile | 2 +-
.../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
.../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
.../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
5 files changed, 402 insertions(+), 402 deletions(-)
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 488a943..66e182c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -573,7 +573,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \
dtb-$(CONFIG_ARCH_OXNAS) += \
wd-mbwe.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-apq8064-arrow-db600c.dtb \
+ qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
deleted file mode 100644
index a3efb97..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
+++ /dev/null
@@ -1,52 +0,0 @@
-&tlmm_pinmux {
- card_detect: card-detect {
- mux {
- pins = "gpio26";
- function = "gpio";
- bias-disable;
- };
- };
-
- pcie_pins: pcie-pinmux {
- mux {
- pins = "gpio27";
- function = "gpio";
- };
- conf {
- pins = "gpio27";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- user_leds: user-leds {
- mux {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- };
-
- conf {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- output-low;
- };
- };
-
- magneto_pins: magneto-pins {
- mux {
- pins = "gpio31", "gpio48";
- function = "gpio";
- bias-disable;
- };
- };
-};
-
-&pm8921_mpps {
- mpp_leds: mpp-leds {
- pinconf {
- pins = "mpp7", "mpp8";
- function = "digital";
- output-low;
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
deleted file mode 100644
index e01b27e..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
+++ /dev/null
@@ -1,349 +0,0 @@
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-db600c-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Arrow Electronics, APQ8064 DB600c";
- compatible = "arrow,db600c", "qcom,apq8064";
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi1_serial;
- i2c0 = &gsbi2_i2c;
- i2c1 = &gsbi3_i2c;
- i2c2 = &gsbi4_i2c;
- i2c3 = &gsbi7_i2c;
- spi0 = &gsbi5_spi;
- };
-
- regulators {
- compatible = "simple-bus";
- vph: regulator-fixed at 1 {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <4500000>;
- regulator-name = "VPH";
- regulator-type = "voltage";
- regulator-boot-on;
- };
-
- /* on board fixed 3.3v supply */
- vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- };
-
- soc {
- rpm at 108000 {
- regulators {
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_s5-supply = <&vph>;
- vdd_s6-supply = <&vph>;
- vdd_s7-supply = <&vph>;
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
- vdd_l3_l15_l17-supply = <&vph>;
- vdd_l4_l14-supply = <&vph>;
- vdd_l5_l8_l16-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l9_l11-supply = <&vph>;
- vdd_l10_l22-supply = <&vph>;
- vdd_l21_l23_l29-supply = <&vph>;
- vdd_l24-supply = <&pm8921_s1>;
- vdd_l25-supply = <&pm8921_s1>;
- vdd_l26-supply = <&pm8921_s7>;
- vdd_l27-supply = <&pm8921_s7>;
- vdd_l28-supply = <&pm8921_s7>;
- vin_lvs1_3_6-supply = <&pm8921_s4>;
- vin_lvs2-supply = <&pm8921_s1>;
- vin_lvs4_5_7-supply = <&pm8921_s4>;
-
- s1 {
- regulator-always-on;
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- };
-
- s3 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <4800000>;
- };
-
- s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s7 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <3200000>;
- };
-
- l3 {
- regulator-min-microvolt = <3050000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
-
- l4 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
-
- l5 {
- regulator-min-microvolt = <2750000>;
- regulator-max-microvolt = <3000000>;
- bias-pull-down;
- regulator-boot-on;
- regulator-always-on;
- };
-
- l6 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- bias-pull-down;
- };
-
- l23 {
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- bias-pull-down;
- };
-
- lvs6 {
- bias-pull-down;
- };
-
- lvs7 {
- bias-pull-down;
- };
- };
- };
-
- gsbi at 12440000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- serial at 12450000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi1_uart_4pins>;
- };
- };
-
- gsbi at 12480000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c at 124a0000 {
- /* On Low speed expansion and Sensors */
- label = "LS-I2C0";
- status = "okay";
- lis3mdl_mag at 1e {
- compatible = "st,lis3mdl-magn";
- reg = <0x1e>;
- vdd-supply = <&vcc3v3>;
- vddio-supply = <&pm8921_s4>;
- pinctrl-names = "default";
- pinctrl-0 = <&magneto_pins>;
- interrupt-parent = <&tlmm_pinmux>;
-
- st,drdy-int-pin = <2>;
- interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
- <31 IRQ_TYPE_EDGE_RISING>; /* INT */
- };
- };
- };
-
- gsbi at 16200000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c at 16280000 {
- /* On Low speed expansion */
- status = "okay";
- label = "LS-I2C1";
- clock-frequency = <200000>;
- eeprom at 52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <64>;
- };
- };
- };
-
- gsbi at 16300000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c at 16380000 {
- /* On High speed expansion */
- label = "HS-CAM-I2C3";
- status = "okay";
- };
- };
-
- gsbi at 1a200000 {
- status = "okay";
- spi at 1a280000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
- };
-
- /* DEBUG UART */
- gsbi at 16600000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
- serial at 16640000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi7_uart_2pins>;
- };
-
- i2c at 16680000 {
- /* On High speed expansion */
- status = "okay";
- label = "HS-CAM-I2C2";
- };
- };
-
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
- compatible = "gpio-leds";
-
- user-led0 {
- label = "user0-led";
- gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- user-led1 {
- label = "user1-led";
- gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- user-led2 {
- label = "user2-led";
- gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- user-led3 {
- label = "user3-led";
- gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- };
-
- wifi-led {
- label = "WiFi-led";
- gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- bt-led {
- label = "BT-led";
- gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- pci at 1b500000 {
- status = "okay";
- vdda-supply = <&pm8921_s3>;
- vdda_phy-supply = <&pm8921_lvs6>;
- vdda_refclk-supply = <&vcc3v3>;
- pinctrl-0 = <&pcie_pins>;
- pinctrl-names = "default";
- perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- phy at 1b400000 {
- status = "okay";
- };
-
- sata at 29000000 {
- status = "okay";
- target-supply = <&pm8921_lvs7>;
- };
-
- /* OTG */
- phy at 12500000 {
- status = "okay";
- dr_mode = "peripheral";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l4>;
- };
-
- phy at 12520000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- phy at 12530000 {
- status = "okay";
- vddcx-supply = <&pm8921_s3>;
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
-
- gadget at 12500000 {
- status = "okay";
- };
-
- /* OTG */
- usb at 12500000 {
- status = "okay";
- };
-
- usb at 12520000 {
- status = "okay";
- };
-
- usb at 12530000 {
- status = "okay";
- };
-
- amba {
- /* eMMC */
- sdcc at 12400000 {
- status = "okay";
- vmmc-supply = <&pm8921_l5>;
- vqmmc-supply = <&pm8921_s4>;
- };
-
- /* External micro SD card */
- sdcc at 12180000 {
- status = "okay";
- vmmc-supply = <&pm8921_l6>;
- pinctrl-names = "default";
- pinctrl-0 = <&card_detect>;
- cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
new file mode 100644
index 0000000..a3efb97
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
@@ -0,0 +1,52 @@
+&tlmm_pinmux {
+ card_detect: card-detect {
+ mux {
+ pins = "gpio26";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ pcie_pins: pcie-pinmux {
+ mux {
+ pins = "gpio27";
+ function = "gpio";
+ };
+ conf {
+ pins = "gpio27";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ user_leds: user-leds {
+ mux {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ };
+
+ conf {
+ pins = "gpio3", "gpio7", "gpio10", "gpio11";
+ function = "gpio";
+ output-low;
+ };
+ };
+
+ magneto_pins: magneto-pins {
+ mux {
+ pins = "gpio31", "gpio48";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+};
+
+&pm8921_mpps {
+ mpp_leds: mpp-leds {
+ pinconf {
+ pins = "mpp7", "mpp8";
+ function = "digital";
+ output-low;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
new file mode 100644
index 0000000..7df0108
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -0,0 +1,349 @@
+#include "qcom-apq8064-v2.0.dtsi"
+#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Arrow Electronics, APQ8064 SD_600eval";
+ compatible = "arrow,sd_600eval", "qcom,apq8064";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi1_serial;
+ i2c0 = &gsbi2_i2c;
+ i2c1 = &gsbi3_i2c;
+ i2c2 = &gsbi4_i2c;
+ i2c3 = &gsbi7_i2c;
+ spi0 = &gsbi5_spi;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ vph: regulator-fixed at 1 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <4500000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ };
+
+ /* on board fixed 3.3v supply */
+ vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ };
+
+ soc {
+ rpm at 108000 {
+ regulators {
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_s5-supply = <&vph>;
+ vdd_s6-supply = <&vph>;
+ vdd_s7-supply = <&vph>;
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l3_l15_l17-supply = <&vph>;
+ vdd_l4_l14-supply = <&vph>;
+ vdd_l5_l8_l16-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l9_l11-supply = <&vph>;
+ vdd_l10_l22-supply = <&vph>;
+ vdd_l21_l23_l29-supply = <&vph>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s1>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ l5 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ l23 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ lvs6 {
+ bias-pull-down;
+ };
+
+ lvs7 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ gsbi at 12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ serial at 12450000 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi1_uart_4pins>;
+ };
+ };
+
+ gsbi at 12480000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c at 124a0000 {
+ /* On Low speed expansion and Sensors */
+ label = "LS-I2C0";
+ status = "okay";
+ lis3mdl_mag at 1e {
+ compatible = "st,lis3mdl-magn";
+ reg = <0x1e>;
+ vdd-supply = <&vcc3v3>;
+ vddio-supply = <&pm8921_s4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&magneto_pins>;
+ interrupt-parent = <&tlmm_pinmux>;
+
+ st,drdy-int-pin = <2>;
+ interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
+ <31 IRQ_TYPE_EDGE_RISING>; /* INT */
+ };
+ };
+ };
+
+ gsbi at 16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c at 16280000 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+ clock-frequency = <200000>;
+ eeprom at 52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <64>;
+ };
+ };
+ };
+
+ gsbi at 16300000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c at 16380000 {
+ /* On High speed expansion */
+ label = "HS-CAM-I2C3";
+ status = "okay";
+ };
+ };
+
+ gsbi at 1a200000 {
+ status = "okay";
+ spi at 1a280000 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+ };
+ };
+
+ /* DEBUG UART */
+ gsbi at 16600000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ serial at 16640000 {
+ label = "LS-UART0";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi7_uart_2pins>;
+ };
+
+ i2c at 16680000 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-CAM-I2C2";
+ };
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+ compatible = "gpio-leds";
+
+ user-led0 {
+ label = "user0-led";
+ gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ user-led1 {
+ label = "user1-led";
+ gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ user-led2 {
+ label = "user2-led";
+ gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ user-led3 {
+ label = "user3-led";
+ gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ };
+
+ wifi-led {
+ label = "WiFi-led";
+ gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ bt-led {
+ label = "BT-led";
+ gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ pci at 1b500000 {
+ status = "okay";
+ vdda-supply = <&pm8921_s3>;
+ vdda_phy-supply = <&pm8921_lvs6>;
+ vdda_refclk-supply = <&vcc3v3>;
+ pinctrl-0 = <&pcie_pins>;
+ pinctrl-names = "default";
+ perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+ };
+
+ phy at 1b400000 {
+ status = "okay";
+ };
+
+ sata at 29000000 {
+ status = "okay";
+ target-supply = <&pm8921_lvs7>;
+ };
+
+ /* OTG */
+ phy at 12500000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+
+ phy at 12520000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ phy at 12530000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ gadget at 12500000 {
+ status = "okay";
+ };
+
+ /* OTG */
+ usb at 12500000 {
+ status = "okay";
+ };
+
+ usb at 12520000 {
+ status = "okay";
+ };
+
+ usb at 12530000 {
+ status = "okay";
+ };
+
+ amba {
+ /* eMMC */
+ sdcc at 12400000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
+ };
+
+ /* External micro SD card */
+ sdcc at 12180000 {
+ status = "okay";
+ vmmc-supply = <&pm8921_l6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&card_detect>;
+ cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
--
2.8.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: dts: sd_600eval: Fix eMMC lockup issue
2016-06-10 9:34 ` Srinivas Kandagatla
@ 2016-06-10 9:34 ` Srinivas Kandagatla
-1 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 9:34 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, David Brown, devicetree, linux-arm-kernel,
linux-kernel, linux-arm-msm, linux-soc, Parth Pancholi
From: Parth Pancholi <parth.pancholi@einfochips.com>
This board locks up if we stress test the eMMC, as the regulator s4 is
unable to supply enough current for all the peripherials attached to it.
As this supply is wired up to most of the peripherials including DDR,
it resulted in such lockup.
This patch fixes this issue by setting s4 regulator correctly with
Auto power mode.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[Srinivas Kandagatla: rewrote the change log]
Tested-by: Girish Sharma <girish.sharma@einfochips.com>
Signed-off-by: Parth Pancholi <parth.pancholi@einfochips.com>
---
arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index 7df0108..39ae2bc 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -1,6 +1,7 @@
#include "qcom-apq8064-v2.0.dtsi"
#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
/ {
model = "Arrow Electronics, APQ8064 SD_600eval";
@@ -82,7 +83,8 @@
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
+ qcom,switch-mode-frequency = <1600000>;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
bias-pull-down;
regulator-always-on;
};
--
2.8.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: dts: sd_600eval: Fix eMMC lockup issue
@ 2016-06-10 9:34 ` Srinivas Kandagatla
0 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 9:34 UTC (permalink / raw)
To: linux-arm-kernel
From: Parth Pancholi <parth.pancholi@einfochips.com>
This board locks up if we stress test the eMMC, as the regulator s4 is
unable to supply enough current for all the peripherials attached to it.
As this supply is wired up to most of the peripherials including DDR,
it resulted in such lockup.
This patch fixes this issue by setting s4 regulator correctly with
Auto power mode.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[Srinivas Kandagatla: rewrote the change log]
Tested-by: Girish Sharma <girish.sharma@einfochips.com>
Signed-off-by: Parth Pancholi <parth.pancholi@einfochips.com>
---
arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index 7df0108..39ae2bc 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -1,6 +1,7 @@
#include "qcom-apq8064-v2.0.dtsi"
#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
/ {
model = "Arrow Electronics, APQ8064 SD_600eval";
@@ -82,7 +83,8 @@
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
+ qcom,switch-mode-frequency = <1600000>;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
bias-pull-down;
regulator-always-on;
};
--
2.8.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
2016-06-10 9:34 ` Srinivas Kandagatla
@ 2016-06-10 12:36 ` Georgi Djakov
-1 siblings, 0 replies; 9+ messages in thread
From: Georgi Djakov @ 2016-06-10 12:36 UTC (permalink / raw)
To: Srinivas Kandagatla, Andy Gross
Cc: Rob Herring, David Brown, devicetree, linux-arm-kernel,
linux-kernel, linux-arm-msm, linux-soc
Hi Srini,
On 06/10/2016 12:34 PM, Srinivas Kandagatla wrote:
> This board has been renamed recently and announced at
> https://eragon.einfochips.com/products/sd-600eval.html
>
> So rename this board files so that it reflects actual product in market.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
> arch/arm/boot/dts/Makefile | 2 +-
> .../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
> arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
> .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
> .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
> 5 files changed, 402 insertions(+), 402 deletions(-)
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>
If you use git format-patch -M, we will see and track the renamed files
easier than deleting and adding the files.
BR,
Georgi
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
@ 2016-06-10 12:36 ` Georgi Djakov
0 siblings, 0 replies; 9+ messages in thread
From: Georgi Djakov @ 2016-06-10 12:36 UTC (permalink / raw)
To: linux-arm-kernel
Hi Srini,
On 06/10/2016 12:34 PM, Srinivas Kandagatla wrote:
> This board has been renamed recently and announced at
> https://eragon.einfochips.com/products/sd-600eval.html
>
> So rename this board files so that it reflects actual product in market.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
> arch/arm/boot/dts/Makefile | 2 +-
> .../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
> arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
> .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
> .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
> 5 files changed, 402 insertions(+), 402 deletions(-)
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>
If you use git format-patch -M, we will see and track the renamed files
easier than deleting and adding the files.
BR,
Georgi
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
2016-06-10 12:36 ` Georgi Djakov
@ 2016-06-10 12:49 ` Srinivas Kandagatla
-1 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 12:49 UTC (permalink / raw)
To: Georgi Djakov, Andy Gross
Cc: Rob Herring, David Brown, devicetree, linux-arm-kernel,
linux-kernel, linux-arm-msm, linux-soc
On 10/06/16 13:36, Georgi Djakov wrote:
> Hi Srini,
>
> On 06/10/2016 12:34 PM, Srinivas Kandagatla wrote:
>> This board has been renamed recently and announced at
>> https://eragon.einfochips.com/products/sd-600eval.html
>>
>> So rename this board files so that it reflects actual product in market.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> ---
>> arch/arm/boot/dts/Makefile | 2 +-
>> .../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
>> arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
>> .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
>> .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
>> 5 files changed, 402 insertions(+), 402 deletions(-)
>> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
>> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
>> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
>> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>>
>
> If you use git format-patch -M, we will see and track the renamed files
> easier than deleting and adding the files.
Yep, that would give good diff stat as well.
Thanks for suggestion, will resend v2 with that change.
--srini
>
> BR,
> Georgi
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval
@ 2016-06-10 12:49 ` Srinivas Kandagatla
0 siblings, 0 replies; 9+ messages in thread
From: Srinivas Kandagatla @ 2016-06-10 12:49 UTC (permalink / raw)
To: linux-arm-kernel
On 10/06/16 13:36, Georgi Djakov wrote:
> Hi Srini,
>
> On 06/10/2016 12:34 PM, Srinivas Kandagatla wrote:
>> This board has been renamed recently and announced at
>> https://eragon.einfochips.com/products/sd-600eval.html
>>
>> So rename this board files so that it reflects actual product in market.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> ---
>> arch/arm/boot/dts/Makefile | 2 +-
>> .../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 ---
>> arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 ---------------------
>> .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++
>> .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++
>> 5 files changed, 402 insertions(+), 402 deletions(-)
>> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
>> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
>> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
>> create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>>
>
> If you use git format-patch -M, we will see and track the renamed files
> easier than deleting and adding the files.
Yep, that would give good diff stat as well.
Thanks for suggestion, will resend v2 with that change.
--srini
>
> BR,
> Georgi
>
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2016-06-10 12:49 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-10 9:34 [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval Srinivas Kandagatla
2016-06-10 9:34 ` Srinivas Kandagatla
2016-06-10 9:34 ` Srinivas Kandagatla
2016-06-10 9:34 ` [PATCH 2/2] ARM: dts: sd_600eval: Fix eMMC lockup issue Srinivas Kandagatla
2016-06-10 9:34 ` Srinivas Kandagatla
2016-06-10 12:36 ` [PATCH 1/2] ARM: dts: apq8064: rename db600c to SD_600eval Georgi Djakov
2016-06-10 12:36 ` Georgi Djakov
2016-06-10 12:49 ` Srinivas Kandagatla
2016-06-10 12:49 ` Srinivas Kandagatla
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.