* [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support
@ 2017-05-13 3:09 Simon Glass
2017-05-13 3:09 ` [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD Simon Glass
` (11 more replies)
0 siblings, 12 replies; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
We have about 6600 CONFIG options to convert to Kconfig at the time of
writing and our target is to complete work by the end of the year. We have
no hope of doing this unless we adopt a somewhat more agressive approach
to dropping old boards and options.
There are a very large number of deprecated or very old options. It does
not make sense to convert these to Kconfig just to carry the debt for
another few years. We should remove these options.
Rather than completely dropping boards, one idea is to remove the parts
of their support which have not been migrated. This was done with some
Samsung boards recently, and it provided the maintainers with enough time
to come in and make the changes.
CONFIG_I2C_SOFT and CONFIG_I2C_HARD are very old. This series removes
them. Boards which rely on these options for I2C support lose some of
their functionality. To regain it they would need to be migrated to driver
model.
Changes in v3:
- Update commit message so that it is unique in the series
- Fix up #ifdef in cmd/eeprom.c
- Drop changes to include/config headers
- Rebase to master
Changes in v2:
- Add new patch to adjust omap boards to not need CONFIG_I2C_HARD
- Drop changes to omap board.c files
- Rebase to master
Simon Glass (12):
i2c: Drop use of CONFIG_I2C_HARD
i2c: powerpc: Remove use of CONFIG_HARD_I2C
i2c: cm5200: Drop use of CONFIG_I2C_HARD
i2c: pdm360ng: Drop use of CONFIG_I2C_HARD
i2c: keymile: Drop use of CONFIG_I2C_HARD
i2c: mxc_i2c: Drop use of CONFIG_I2C_HARD
i2c: omap: Modify code to work without CONFIG_I2C_HARD
i2c: Finish dropping use of CONFIG_I2C_HARD
i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX
i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT
Drop CONFIG_I2CFAST
Drop use of CONFIG_I2C_SOFT
README | 64 +--
arch/arm/include/asm/arch-armada100/config.h | 12 -
arch/powerpc/cpu/mpc512x/Makefile | 1 -
arch/powerpc/cpu/mpc512x/i2c.c | 386 --------------
arch/powerpc/cpu/mpc5xxx/Makefile | 1 -
arch/powerpc/cpu/mpc5xxx/i2c.c | 456 -----------------
arch/powerpc/cpu/mpc8260/Makefile | 2 +-
arch/powerpc/cpu/mpc8260/commproc.c | 4 -
arch/powerpc/cpu/mpc8260/i2c.c | 741 ---------------------------
arch/powerpc/cpu/mpc8xx/Makefile | 1 -
arch/powerpc/cpu/mpc8xx/i2c.c | 672 ------------------------
board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c | 12 +-
board/cm5200/cm5200.c | 36 +-
board/cm5200/cmd_cm5200.c | 32 +-
board/davedenx/aria/aria.c | 3 -
board/esd/mecp5123/mecp5123.c | 12 +-
board/freescale/m52277evb/README | 1 -
board/freescale/m53017evb/README | 1 -
board/freescale/m5373evb/README | 1 -
board/freescale/m54455evb/README | 1 -
board/freescale/m547xevb/README | 1 -
board/freescale/mpc5121ads/mpc5121ads.c | 21 -
board/ifm/ac14xx/ac14xx.c | 53 +-
board/keymile/km82xx/km82xx.c | 5 -
board/keymile/km_arm/km_arm.c | 4 -
board/pdm360ng/pdm360ng.c | 30 --
board/renesas/r0p7734/r0p7734.c | 12 +-
board/ti/am335x/board.c | 3 +-
board/ti/am43xx/board.c | 3 +-
board/tqc/tqm5200/tqm5200.c | 18 +-
cmd/eeprom.c | 2 -
common/board_f.c | 4 +-
common/board_r.c | 17 -
common/stdio.c | 5 +-
configs/MiniFAP_defconfig | 2 -
configs/O2D300_defconfig | 1 -
configs/O2DNT2_RAMBOOT_defconfig | 1 -
configs/O2DNT2_defconfig | 1 -
configs/O2D_defconfig | 1 -
configs/O2I_defconfig | 1 -
configs/O2MNT_O2M110_defconfig | 1 -
configs/O2MNT_O2M112_defconfig | 1 -
configs/O2MNT_O2M113_defconfig | 1 -
configs/O2MNT_defconfig | 1 -
configs/O3DNT_defconfig | 1 -
configs/TQM5200S_HIGHBOOT_defconfig | 2 -
configs/TQM5200S_defconfig | 2 -
configs/TQM5200_B_HIGHBOOT_defconfig | 2 -
configs/TQM5200_B_defconfig | 2 -
configs/TQM5200_STK100_defconfig | 2 -
configs/TQM5200_defconfig | 2 -
configs/a4m072_defconfig | 1 -
configs/ac14xx_defconfig | 1 -
configs/ap_sh4a_4a_defconfig | 1 -
configs/apx4devkit_defconfig | 2 -
configs/aria_defconfig | 1 -
configs/aspenite_defconfig | 1 -
configs/cam5200_defconfig | 2 -
configs/cam5200_niosflash_defconfig | 2 -
configs/charon_defconfig | 1 -
configs/cm5200_defconfig | 1 -
configs/digsy_mtc_RAMBOOT_defconfig | 2 -
configs/digsy_mtc_defconfig | 2 -
configs/digsy_mtc_rev5_RAMBOOT_defconfig | 2 -
configs/digsy_mtc_rev5_defconfig | 2 -
configs/fo300_defconfig | 2 -
configs/gplugd_defconfig | 1 -
configs/ipek01_defconfig | 2 -
configs/m28evk_defconfig | 1 -
configs/mecp5123_defconfig | 2 -
configs/motionpro_defconfig | 2 -
configs/mpc5121ads_defconfig | 2 -
configs/mpc5121ads_rev2_defconfig | 2 -
configs/pcm030_LOWBOOT_defconfig | 2 -
configs/pcm030_defconfig | 2 -
configs/pdm360ng_defconfig | 2 -
configs/r0p7734_defconfig | 1 -
configs/v38b_defconfig | 2 -
drivers/i2c/fsl_i2c.c | 9 -
drivers/i2c/fti2c010.c | 9 -
drivers/i2c/mxc_i2c.c | 4 -
include/common.h | 10 +
include/configs/M54418TWR.h | 1 -
include/configs/TQM5200.h | 64 +--
include/configs/a4m072.h | 20 -
include/configs/ac14xx.h | 18 -
include/configs/ap_sh4a_4a.h | 14 -
include/configs/apx4devkit.h | 6 -
include/configs/aria.h | 21 -
include/configs/axs10x.h | 2 +-
include/configs/cm5200.h | 12 +-
include/configs/digsy_mtc.h | 31 --
include/configs/ids8313.h | 1 -
include/configs/ipek01.h | 23 -
include/configs/jupiter.h | 19 -
include/configs/m28evk.h | 6 -
include/configs/manroland/mpc5200-common.h | 176 +++++++
include/configs/mecp5123.h | 18 +-
include/configs/motionpro.h | 22 -
include/configs/mpc5121ads.h | 18 -
include/configs/mxs.h | 10 -
include/configs/o2dnt-common.h | 22 -
include/configs/pcm030.h | 31 +-
include/configs/pdm360ng.h | 30 --
include/configs/r0p7734.h | 14 -
include/configs/s32v234evb.h | 10 -
include/configs/v38b.h | 21 -
include/i2c.h | 3 -
scripts/config_whitelist.txt | 3 -
109 files changed, 220 insertions(+), 3113 deletions(-)
delete mode 100644 arch/powerpc/cpu/mpc512x/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc5xxx/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc8260/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc8xx/i2c.c
create mode 100644 include/configs/manroland/mpc5200-common.h
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:22 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C Simon Glass
` (10 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
README | 17 +--
arch/arm/include/asm/arch-armada100/config.h | 12 --
board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c | 12 +-
board/cm5200/cm5200.c | 32 ++---
board/cm5200/cmd_cm5200.c | 32 +----
board/davedenx/aria/aria.c | 3 -
board/esd/mecp5123/mecp5123.c | 12 +-
board/freescale/mpc5121ads/mpc5121ads.c | 21 ----
board/ifm/ac14xx/ac14xx.c | 53 +-------
board/renesas/r0p7734/r0p7734.c | 12 +-
board/tqc/tqm5200/tqm5200.c | 18 +--
configs/MiniFAP_defconfig | 2 -
configs/O2D300_defconfig | 1 -
configs/O2DNT2_RAMBOOT_defconfig | 1 -
configs/O2DNT2_defconfig | 1 -
configs/O2D_defconfig | 1 -
configs/O2I_defconfig | 1 -
configs/O2MNT_O2M110_defconfig | 1 -
configs/O2MNT_O2M112_defconfig | 1 -
configs/O2MNT_O2M113_defconfig | 1 -
configs/O2MNT_defconfig | 1 -
configs/O3DNT_defconfig | 1 -
configs/TQM5200S_HIGHBOOT_defconfig | 2 -
configs/TQM5200S_defconfig | 2 -
configs/TQM5200_B_HIGHBOOT_defconfig | 2 -
configs/TQM5200_B_defconfig | 2 -
configs/TQM5200_STK100_defconfig | 2 -
configs/TQM5200_defconfig | 2 -
configs/a4m072_defconfig | 1 -
configs/ac14xx_defconfig | 1 -
configs/ap_sh4a_4a_defconfig | 1 -
configs/apx4devkit_defconfig | 2 -
configs/aria_defconfig | 1 -
configs/aspenite_defconfig | 1 -
configs/cam5200_defconfig | 2 -
configs/cam5200_niosflash_defconfig | 2 -
configs/charon_defconfig | 1 -
configs/cm5200_defconfig | 1 -
configs/digsy_mtc_RAMBOOT_defconfig | 2 -
configs/digsy_mtc_defconfig | 2 -
configs/digsy_mtc_rev5_RAMBOOT_defconfig | 2 -
configs/digsy_mtc_rev5_defconfig | 2 -
configs/fo300_defconfig | 2 -
configs/gplugd_defconfig | 1 -
configs/ipek01_defconfig | 2 -
configs/m28evk_defconfig | 1 -
configs/mecp5123_defconfig | 2 -
configs/motionpro_defconfig | 2 -
configs/mpc5121ads_defconfig | 2 -
configs/mpc5121ads_rev2_defconfig | 2 -
configs/pcm030_LOWBOOT_defconfig | 2 -
configs/pcm030_defconfig | 2 -
configs/pdm360ng_defconfig | 2 -
configs/r0p7734_defconfig | 1 -
configs/v38b_defconfig | 2 -
include/common.h | 10 ++
include/configs/M54418TWR.h | 1 -
include/configs/TQM5200.h | 64 +---------
include/configs/a4m072.h | 20 ---
include/configs/ac14xx.h | 18 ---
include/configs/ap_sh4a_4a.h | 14 ---
include/configs/apx4devkit.h | 6 -
include/configs/aria.h | 21 ----
include/configs/axs10x.h | 2 +-
include/configs/cm5200.h | 12 +-
include/configs/digsy_mtc.h | 31 -----
include/configs/ids8313.h | 1 -
include/configs/ipek01.h | 23 ----
include/configs/jupiter.h | 19 ---
include/configs/m28evk.h | 6 -
include/configs/manroland/mpc5200-common.h | 176 +++++++++++++++++++++++++++
include/configs/mecp5123.h | 18 +--
include/configs/motionpro.h | 22 ----
include/configs/mpc5121ads.h | 18 ---
include/configs/mxs.h | 10 --
include/configs/o2dnt-common.h | 22 ----
include/configs/pcm030.h | 31 +----
include/configs/pdm360ng.h | 30 -----
include/configs/r0p7734.h | 14 ---
include/configs/s32v234evb.h | 10 --
include/configs/v38b.h | 21 ----
81 files changed, 211 insertions(+), 701 deletions(-)
create mode 100644 include/configs/manroland/mpc5200-common.h
diff --git a/README b/README
index 2ca0102b57..86f0814f79 100644
--- a/README
+++ b/README
@@ -2213,22 +2213,9 @@ The following options need to be configured:
- approved multibus support
- better i2c mux support
- ** Please consider updating your I2C driver now. **
+ ** CONFIG_HARD_I2C is now being removed **
- These enable legacy I2C serial bus commands. Defining
- CONFIG_HARD_I2C will include the appropriate I2C driver
- for the selected CPU.
-
- This will allow you to use i2c commands at the u-boot
- command line (as long as you set CONFIG_CMD_I2C in
- CONFIG_COMMANDS) and communicate with i2c based realtime
- clock chips. See common/cmd_i2c.c for a description of the
- command line interface.
-
- CONFIG_HARD_I2C selects a hardware I2C controller.
-
- There are several other quantities that must also be
- defined when you define CONFIG_HARD_I2C.
+----under removal:
In both cases you will need to define CONFIG_SYS_I2C_SPEED
to be the frequency (in Hz) at which you wish your i2c bus
diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
index 6ebc759f4b..113e1c73f3 100644
--- a/arch/arm/include/asm/arch-armada100/config.h
+++ b/arch/arm/include/asm/arch-armada100/config.h
@@ -24,17 +24,5 @@
#define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE
#define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register
represents UART Unit Enable */
-/*
- * I2C definition
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MV 1
-#define CONFIG_MV_I2C_NUM 2
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000}
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 0
-#define CONFIG_SYS_I2C_SLAVE 0xfe
-#endif
#endif /* _ARMD1_CONFIG_H */
diff --git a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
index 31418a1f96..9205c22e0b 100644
--- a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
+++ b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
@@ -156,17 +156,7 @@ int board_init(void)
int board_late_init(void)
{
- u8 mac[6];
-
- /* Read Mac Address and set*/
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
-
- /* Read MAC address */
- i2c_read(0x50, 0x0, 0, mac, 6);
-
- if (is_valid_ethaddr(mac))
- eth_setenv_enetaddr("ethaddr", mac);
+ printf("Cannot use I2C to get MAC address\n");
return 0;
}
diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
index 7b862355c8..2f55191caf 100644
--- a/board/cm5200/cm5200.c
+++ b/board/cm5200/cm5200.c
@@ -161,14 +161,7 @@ int dram_init(void)
*/
static void read_hw_id(hw_id_t hw_id)
{
- int i;
- for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
- if (i2c_read(CONFIG_SYS_I2C_EEPROM,
- hw_id_format[i].offset,
- 2,
- (uchar *)&hw_id[i][0],
- hw_id_format[i].length) != 0)
- printf("ERROR: can't read HW ID from EEPROM\n");
+ printf("ERROR: can't read HW ID from EEPROM\n");
}
@@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf)
strcat(buf, tmp);
}
-
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
/*
* Compose string with hostname.
* buf is assumed to have enough space, and be null-terminated.
@@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf)
*p = tolower(*p);
}
-
+#endif
#ifdef CONFIG_OF_BOARD_SETUP
/*
@@ -270,15 +263,6 @@ int checkboard(void)
hw_id_t hw_id_tmp;
char module_name_tmp[MODULE_NAME_MAXLEN] = "";
- /*
- * We need I2C to access HW ID data from EEPROM, so we call i2c_init()
- * here despite the fact that it will be called again later on. We
- * also use a little trick to silence I2C-related output.
- */
- gd->flags |= GD_FLG_SILENT;
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- gd->flags &= ~GD_FLG_SILENT;
-
read_hw_id(hw_id_tmp);
identify_module(hw_id_tmp); /* this sets gd->board_type */
compose_module_name(hw_id_tmp, module_name_tmp);
@@ -334,16 +318,16 @@ int misc_init_r(void)
" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
CONFIG_MAC_OFFSET);
}
+ hostname[0] = 0x00;
+ /* set the hostname appropriate to the module we're running on */
+ compose_hostname(hw_id, hostname);
+ setenv("hostname", hostname);
+
#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
if (!getenv("ethaddr"))
printf(LOG_PREFIX "MAC address not set, networking is not "
"operational\n");
- /* set the hostname appropriate to the module we're running on */
- hostname[0] = 0x00;
- compose_hostname(hw_id, hostname);
- setenv("hostname", hostname);
-
return 0;
}
#endif /* CONFIG_MISC_INIT_R */
diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c
index 9c40ad7b2a..60097dc8c7 100644
--- a/board/cm5200/cmd_cm5200.c
+++ b/board/cm5200/cmd_cm5200.c
@@ -13,34 +13,6 @@
#ifdef CONFIG_CMD_BSP
-static int do_i2c_test(char * const argv[])
-{
- unsigned char temp, temp1;
-
- printf("Starting I2C Test\n"
- "Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
- "Please press any key to start\n\n");
- getc();
-
- temp = 0xf0; /* set io 0-4 as output */
- i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1);
-
- printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
- "Press any key to stop\n\n");
-
- while (!tstc()) {
- i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1);
- temp1 = (temp >> 4) & 0x03;
- temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
- temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
- temp = temp1;
- i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1);
- }
- getc();
-
- return 0;
-}
-
static int do_usb_test(char * const argv[])
{
int i;
@@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
switch (argc) {
case 2:
- if (strncmp(argv[1], "i2c", 3) == 0)
- rcode = do_i2c_test(argv);
- else if (strncmp(argv[1], "led", 3) == 0)
+ if (strncmp(argv[1], "led", 3) == 0)
rcode = do_led_test(argv);
else if (strncmp(argv[1], "usb", 3) == 0)
rcode = do_usb_test(argv);
diff --git a/board/davedenx/aria/aria.c b/board/davedenx/aria/aria.c
index e3441cad4e..e389819e9d 100644
--- a/board/davedenx/aria/aria.c
+++ b/board/davedenx/aria/aria.c
@@ -29,9 +29,6 @@ int misc_init_r(void)
{
u32 tmp;
- /* we use I2C-2 for on-board eeprom */
- i2c_set_bus_num(2);
-
tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE);
printf("FPGA: %u-%u.%u.%u\n",
(tmp & 0xFF000000) >> 24,
diff --git a/board/esd/mecp5123/mecp5123.c b/board/esd/mecp5123/mecp5123.c
index 66dc407bae..78a6b66110 100644
--- a/board/esd/mecp5123/mecp5123.c
+++ b/board/esd/mecp5123/mecp5123.c
@@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR;
int eeprom_write_enable(unsigned dev_addr, int state)
{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
- if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR)
- return -1;
-
- if (state == 0)
- setbits_be32(&im->gpio.gpdat, 0x00100000);
- else
- clrbits_be32(&im->gpio.gpdat, 0x00100000);
-
- return 0;
+ return -ENOSYS;
}
int board_early_init_f(void)
diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c
index f87579f193..d729056fd0 100644
--- a/board/freescale/mpc5121ads/mpc5121ads.c
+++ b/board/freescale/mpc5121ads/mpc5121ads.c
@@ -174,27 +174,6 @@ int dram_init(void)
int misc_init_r(void)
{
- u8 tmp_val;
-
- /* Using this for DIU init before the driver in linux takes over
- * Enable the TFP410 Encoder (I2C address 0x38)
- */
-
- i2c_set_bus_num(2);
- tmp_val = 0xBF;
- i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
- /* Verify if enabled */
- tmp_val = 0;
- i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
- debug("DVI Encoder Read: 0x%02x\n", tmp_val);
-
- tmp_val = 0x10;
- i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
- /* Verify if enabled */
- tmp_val = 0;
- i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
- debug("DVI Encoder Read: 0x%02x\n", tmp_val);
-
return 0;
}
diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c
index 348613736d..cd79e804a0 100644
--- a/board/ifm/ac14xx/ac14xx.c
+++ b/board/ifm/ac14xx/ac14xx.c
@@ -17,7 +17,6 @@
#include <i2c.h>
#endif
-static int eeprom_diag;
static int mac_diag;
static int gpio_diag;
@@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout {
#define HW_COMP_MAINCPU 2
static struct eeprom_layout eeprom_content;
-static int eeprom_was_read; /* has_been_read */
static int eeprom_is_valid;
static int eeprom_version;
@@ -153,53 +151,7 @@ static int eeprom_version;
static int read_eeprom(void)
{
- int eeprom_datalen;
- int ret;
-
- if (eeprom_was_read)
- return 0;
-
- eeprom_is_valid = 0;
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
- (uchar *)&eeprom_content, sizeof(eeprom_content));
- if (eeprom_diag) {
- printf("DIAG: %s() read rc[%d], size[%d]\n",
- __func__, ret, sizeof(eeprom_content));
- }
-
- if (ret != 0)
- return -1;
-
- eeprom_was_read = 1;
-
- /*
- * check validity of EEPROM content
- * (check version, length, optionally checksum)
- */
- eeprom_is_valid = 1;
- eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
- eeprom_version = get_eeprom_field_int(eeprom_content.version);
-
- if (eeprom_diag) {
- printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
- __func__, eeprom_content.magic[0],
- eeprom_content.magic[1], eeprom_content.magic[2],
- eeprom_datalen, eeprom_version, eeprom_content.type);
- }
- if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
- eeprom_is_valid = 0;
- if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
- eeprom_is_valid = 0;
- if ((eeprom_version != 1) && (eeprom_version != 2))
- eeprom_is_valid = 0;
- if (eeprom_content.type != HW_COMP_MAINCPU)
- eeprom_is_valid = 0;
-
- if (eeprom_diag)
- printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);
-
- return ret;
+ return -ENOSYS;
}
int mac_read_from_eeprom(void)
@@ -324,9 +276,6 @@ int misc_init_r(void)
char *s;
int want_recovery;
- /* we use bus I2C-0 for the on-board eeprom */
- i2c_set_bus_num(0);
-
/* setup GPIO directions and initial values */
gpio_configure();
diff --git a/board/renesas/r0p7734/r0p7734.c b/board/renesas/r0p7734/r0p7734.c
index 360e0a1a6f..d0b4537513 100644
--- a/board/renesas/r0p7734/r0p7734.c
+++ b/board/renesas/r0p7734/r0p7734.c
@@ -44,17 +44,7 @@ int board_init(void)
int board_late_init(void)
{
- u8 mac[6];
-
- /* Read Mac Address and set*/
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
-
- /* Read MAC address */
- i2c_read(0x50, 0x10, 0, mac, 6);
-
- if (is_valid_ethaddr(mac))
- eth_setenv_enetaddr("ethaddr", mac);
+ printf("Cannot get MAC address from I2C\n");
return 0;
}
diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c
index 92db093dbf..c48ab11fc4 100644
--- a/board/tqc/tqm5200/tqm5200.c
+++ b/board/tqc/tqm5200/tqm5200.c
@@ -486,20 +486,14 @@ int board_early_init_f (void)
static int tfp410_read_reg(int reg, uchar *buf)
{
- if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) {
- puts ("Error reading the chip.\n");
- return 1;
- }
- return 0;
+ puts("Error reading the chip.\n");
+ return -ENOSYS;
}
static int tfp410_write_reg(int reg, uchar buf)
{
- if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) {
- puts ("Error writing the chip.\n");
- return 1;
- }
- return 0;
+ puts("Error writing the chip.\n");
+ return -ENOSYS;
}
typedef struct _tfp410_config {
@@ -525,12 +519,9 @@ static int charon_last_stage_init(void)
{
volatile struct mpc5xxx_lpb *lpb =
(struct mpc5xxx_lpb *) MPC5XXX_LPB;
- int oldbus = i2c_get_bus_num();
uchar buf;
int i = 0;
- i2c_set_bus_num(CONFIG_SYS_TFP410_BUS);
-
/* check version */
if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0)
return -1;
@@ -551,7 +542,6 @@ static int charon_last_stage_init(void)
i++;
}
printf("TFP410 initialized.\n");
- i2c_set_bus_num(oldbus);
/* set deadcycle for cs3 to 0 */
setbits_be32(&lpb->cs_deadcycle, 0xffffcfff);
diff --git a/configs/MiniFAP_defconfig b/configs/MiniFAP_defconfig
index 7d719f81f5..02ca577e28 100644
--- a/configs/MiniFAP_defconfig
+++ b/configs/MiniFAP_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/O2D300_defconfig b/configs/O2D300_defconfig
index 38101f05df..c0e9541b87 100644
--- a/configs/O2D300_defconfig
+++ b/configs/O2D300_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2DNT2_RAMBOOT_defconfig b/configs/O2DNT2_RAMBOOT_defconfig
index 83006e5582..8cff44cf36 100644
--- a/configs/O2DNT2_RAMBOOT_defconfig
+++ b/configs/O2DNT2_RAMBOOT_defconfig
@@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
CONFIG_AUTOBOOT_STOP_STR="++++++++++"
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2DNT2_defconfig b/configs/O2DNT2_defconfig
index 4202d85203..f29abb83bc 100644
--- a/configs/O2DNT2_defconfig
+++ b/configs/O2DNT2_defconfig
@@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
CONFIG_AUTOBOOT_STOP_STR="++++++++++"
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2D_defconfig b/configs/O2D_defconfig
index b84a1c8839..534cfe12e2 100644
--- a/configs/O2D_defconfig
+++ b/configs/O2D_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2I_defconfig b/configs/O2I_defconfig
index efcc769ff4..acf42abe29 100644
--- a/configs/O2I_defconfig
+++ b/configs/O2I_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_O2M110_defconfig b/configs/O2MNT_O2M110_defconfig
index abdc53df21..de647c76b9 100644
--- a/configs/O2MNT_O2M110_defconfig
+++ b/configs/O2MNT_O2M110_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_O2M112_defconfig b/configs/O2MNT_O2M112_defconfig
index 06089fe3cf..b243e9cc0e 100644
--- a/configs/O2MNT_O2M112_defconfig
+++ b/configs/O2MNT_O2M112_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_O2M113_defconfig b/configs/O2MNT_O2M113_defconfig
index 1ea3f3a09b..1584058289 100644
--- a/configs/O2MNT_O2M113_defconfig
+++ b/configs/O2MNT_O2M113_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O2MNT_defconfig b/configs/O2MNT_defconfig
index 0209085605..20bd31466e 100644
--- a/configs/O2MNT_defconfig
+++ b/configs/O2MNT_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/O3DNT_defconfig b/configs/O3DNT_defconfig
index 5ce4140859..ea769e7edc 100644
--- a/configs/O3DNT_defconfig
+++ b/configs/O3DNT_defconfig
@@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/TQM5200S_HIGHBOOT_defconfig b/configs/TQM5200S_HIGHBOOT_defconfig
index d0cd50a63c..d07596add0 100644
--- a/configs/TQM5200S_HIGHBOOT_defconfig
+++ b/configs/TQM5200S_HIGHBOOT_defconfig
@@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200S_defconfig b/configs/TQM5200S_defconfig
index 5324a9a11c..af3225554b 100644
--- a/configs/TQM5200S_defconfig
+++ b/configs/TQM5200S_defconfig
@@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_B_HIGHBOOT_defconfig b/configs/TQM5200_B_HIGHBOOT_defconfig
index 2f933e6cab..37d6767f28 100644
--- a/configs/TQM5200_B_HIGHBOOT_defconfig
+++ b/configs/TQM5200_B_HIGHBOOT_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_B_defconfig b/configs/TQM5200_B_defconfig
index f204484f59..5e0cf9ea47 100644
--- a/configs/TQM5200_B_defconfig
+++ b/configs/TQM5200_B_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_STK100_defconfig b/configs/TQM5200_STK100_defconfig
index db9bb8a30d..7b4b030d74 100644
--- a/configs/TQM5200_STK100_defconfig
+++ b/configs/TQM5200_STK100_defconfig
@@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/TQM5200_defconfig b/configs/TQM5200_defconfig
index eec60f1be4..4792639653 100644
--- a/configs/TQM5200_defconfig
+++ b/configs/TQM5200_defconfig
@@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -18,7 +17,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/a4m072_defconfig b/configs/a4m072_defconfig
index ce5edcbf01..0054d4cddb 100644
--- a/configs/a4m072_defconfig
+++ b/configs/a4m072_defconfig
@@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="asdfg"
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
diff --git a/configs/ac14xx_defconfig b/configs/ac14xx_defconfig
index e3b7793e04..930ec8acf2 100644
--- a/configs/ac14xx_defconfig
+++ b/configs/ac14xx_defconfig
@@ -5,7 +5,6 @@ CONFIG_FIT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_PROMPT="ac14xx> "
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/ap_sh4a_4a_defconfig b/configs/ap_sh4a_4a_defconfig
index 75cf53fe21..41c8be9120 100644
--- a/configs/ap_sh4a_4a_defconfig
+++ b/configs/ap_sh4a_4a_defconfig
@@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
# CONFIG_CMD_ENV_EXISTS is not set
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_I2C=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_ECHO is not set
# CONFIG_CMD_ITEST is not set
diff --git a/configs/apx4devkit_defconfig b/configs/apx4devkit_defconfig
index e2061a2cce..5c30fe3ce7 100644
--- a/configs/apx4devkit_defconfig
+++ b/configs/apx4devkit_defconfig
@@ -14,14 +14,12 @@ CONFIG_HUSH_PARSER=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_MMC=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
diff --git a/configs/aria_defconfig b/configs/aria_defconfig
index 963661ab2d..0f1432f9a8 100644
--- a/configs/aria_defconfig
+++ b/configs/aria_defconfig
@@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
diff --git a/configs/aspenite_defconfig b/configs/aspenite_defconfig
index 26654426ed..0ac39eabd2 100644
--- a/configs/aspenite_defconfig
+++ b/configs/aspenite_defconfig
@@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
diff --git a/configs/cam5200_defconfig b/configs/cam5200_defconfig
index 92985ab3d6..46a24f56ab 100644
--- a/configs/cam5200_defconfig
+++ b/configs/cam5200_defconfig
@@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_ISO_PARTITION=y
diff --git a/configs/cam5200_niosflash_defconfig b/configs/cam5200_niosflash_defconfig
index 32bc58ee9b..6b9877ff21 100644
--- a/configs/cam5200_niosflash_defconfig
+++ b/configs/cam5200_niosflash_defconfig
@@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_ISO_PARTITION=y
diff --git a/configs/charon_defconfig b/configs/charon_defconfig
index ec22a6368f..8a1429037a 100644
--- a/configs/charon_defconfig
+++ b/configs/charon_defconfig
@@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
diff --git a/configs/cm5200_defconfig b/configs/cm5200_defconfig
index 7d8d01aaaa..d3369f4455 100644
--- a/configs/cm5200_defconfig
+++ b/configs/cm5200_defconfig
@@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5
CONFIG_SILENT_CONSOLE=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
diff --git a/configs/digsy_mtc_RAMBOOT_defconfig b/configs/digsy_mtc_RAMBOOT_defconfig
index 0d11eec75a..86b2b0d804 100644
--- a/configs/digsy_mtc_RAMBOOT_defconfig
+++ b/configs/digsy_mtc_RAMBOOT_defconfig
@@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/digsy_mtc_defconfig b/configs/digsy_mtc_defconfig
index dc17ab4406..85b7f850f7 100644
--- a/configs/digsy_mtc_defconfig
+++ b/configs/digsy_mtc_defconfig
@@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -19,7 +18,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/digsy_mtc_rev5_RAMBOOT_defconfig b/configs/digsy_mtc_rev5_RAMBOOT_defconfig
index 4ab11c755b..7ec8650aca 100644
--- a/configs/digsy_mtc_rev5_RAMBOOT_defconfig
+++ b/configs/digsy_mtc_rev5_RAMBOOT_defconfig
@@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/digsy_mtc_rev5_defconfig b/configs/digsy_mtc_rev5_defconfig
index 1f3f3c8bb6..b4b8533063 100644
--- a/configs/digsy_mtc_rev5_defconfig
+++ b/configs/digsy_mtc_rev5_defconfig
@@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/fo300_defconfig b/configs/fo300_defconfig
index b4f334a436..00418153be 100644
--- a/configs/fo300_defconfig
+++ b/configs/fo300_defconfig
@@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -21,7 +20,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
diff --git a/configs/gplugd_defconfig b/configs/gplugd_defconfig
index 97bb976803..f44b68dae8 100644
--- a/configs/gplugd_defconfig
+++ b/configs/gplugd_defconfig
@@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_SETEXPR is not set
diff --git a/configs/ipek01_defconfig b/configs/ipek01_defconfig
index cac9326b6c..690bc0f461 100644
--- a/configs/ipek01_defconfig
+++ b/configs/ipek01_defconfig
@@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
diff --git a/configs/m28evk_defconfig b/configs/m28evk_defconfig
index 6acbd77d5f..0ab7f6bb3c 100644
--- a/configs/m28evk_defconfig
+++ b/configs/m28evk_defconfig
@@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
diff --git a/configs/mecp5123_defconfig b/configs/mecp5123_defconfig
index ebf5415464..db52077e1a 100644
--- a/configs/mecp5123_defconfig
+++ b/configs/mecp5123_defconfig
@@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig
index 91384a6259..5040ea5742 100644
--- a/configs/motionpro_defconfig
+++ b/configs/motionpro_defconfig
@@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_BEDBUG=y
CONFIG_LED_STATUS=y
diff --git a/configs/mpc5121ads_defconfig b/configs/mpc5121ads_defconfig
index c0af8127b5..47c4e5ace7 100644
--- a/configs/mpc5121ads_defconfig
+++ b/configs/mpc5121ads_defconfig
@@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_MAC_PARTITION=y
diff --git a/configs/mpc5121ads_rev2_defconfig b/configs/mpc5121ads_rev2_defconfig
index ad46e02e94..ef700d0773 100644
--- a/configs/mpc5121ads_rev2_defconfig
+++ b/configs/mpc5121ads_rev2_defconfig
@@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_MAC_PARTITION=y
diff --git a/configs/pcm030_LOWBOOT_defconfig b/configs/pcm030_LOWBOOT_defconfig
index d19908ca8f..2933326e5d 100644
--- a/configs/pcm030_LOWBOOT_defconfig
+++ b/configs/pcm030_LOWBOOT_defconfig
@@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
CONFIG_BOOTDELAY=3
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
-CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
diff --git a/configs/pcm030_defconfig b/configs/pcm030_defconfig
index ef5c85888c..ff9f4e9f4f 100644
--- a/configs/pcm030_defconfig
+++ b/configs/pcm030_defconfig
@@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=3
CONFIG_SYS_PROMPT="uboot> "
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
-CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
diff --git a/configs/pdm360ng_defconfig b/configs/pdm360ng_defconfig
index f45a90caf9..4ef0df1aa8 100644
--- a/configs/pdm360ng_defconfig
+++ b/configs/pdm360ng_defconfig
@@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
# CONFIG_PCI is not set
diff --git a/configs/r0p7734_defconfig b/configs/r0p7734_defconfig
index c5c3d52718..91b08dc24f 100644
--- a/configs/r0p7734_defconfig
+++ b/configs/r0p7734_defconfig
@@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
# CONFIG_CMD_ENV_EXISTS is not set
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_I2C=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_ECHO is not set
# CONFIG_CMD_ITEST is not set
diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig
index db4c47c3d2..18dc039d93 100644
--- a/configs/v38b_defconfig
+++ b/configs/v38b_defconfig
@@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y
CONFIG_TARGET_V38B=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_MAC_PARTITION=y
diff --git a/include/common.h b/include/common.h
index 83e4037a86..45f190a600 100644
--- a/include/common.h
+++ b/include/common.h
@@ -499,9 +499,19 @@ void reset_phy (void);
void fdc_hw_init (void);
/* $(BOARD)/eeprom.c */
+#ifdef CONFIG_CMD_EEPROM
void eeprom_init (int bus);
int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+#else
+/*
+ * Some EEPROM code is depecated because it used the legacy I2C interface. Add
+ * some macros here so we don't have to touch every one of those uses
+ */
+#define eeprom_init(bus)
+#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
+#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
+#endif
/*
* Set this up regardless of board
diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h
index 1817571efe..7b162cccef 100644
--- a/include/configs/M54418TWR.h
+++ b/include/configs/M54418TWR.h
@@ -166,7 +166,6 @@
/* I2c */
#undef CONFIG_SYS_FSL_I2C
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED 80000
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 13f4ef67e1..19e0b1be1b 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -124,8 +124,7 @@
#ifndef CONFIG_CAM5200
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_I2C)
+ CONFIG_SYS_POST_CPU)
#endif
#ifdef CONFIG_POST
@@ -144,7 +143,6 @@
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO
@@ -278,54 +276,6 @@
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-Boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-
-/*
- * HW-Monitor configuration on Mini-FAP
- */
-#if defined (CONFIG_MINIFAP)
-#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C
-#endif
-
-/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_MINIFAP)
-#undef CONFIG_SYS_POST_I2C_ADDRS
-#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_HWMON_ADDR, \
- CONFIG_SYS_I2C_SLAVE}
-#endif
-
/*
* Flash configuration
*/
@@ -544,18 +494,6 @@
#endif
#endif
-/*
- * RTC configuration
- */
-#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
-# define CONFIG_RTC_M41T11 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
- year */
-#else
-# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
-#endif
-
/*
* Miscellaneous configurable options
*/
diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h
index 79099518e7..2ea43ffce1 100644
--- a/include/configs/a4m072.h
+++ b/include/configs/a4m072.h
@@ -81,7 +81,6 @@
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#if defined(CONFIG_PCI)
@@ -145,25 +144,6 @@
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_EEPROM_WREN 1
-#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4
-
/*
* Flash configuration
*/
diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h
index ee015bb83d..2a46e9b864 100644
--- a/include/configs/ac14xx.h
+++ b/include/configs/ac14xx.h
@@ -336,28 +336,11 @@
#define CONFIG_CMDLINE_EDITING 1 /* command line history */
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration for Atmel AT24C01:
- * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-
/*
* Ethernet configuration
*/
@@ -384,7 +367,6 @@
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h
index 5f5882dc8e..d3d72b634d 100644
--- a/include/configs/ap_sh4a_4a.h
+++ b/include/configs/ap_sh4a_4a.h
@@ -35,20 +35,6 @@
#define CONFIG_BITBANGMII
#define CONFIG_BITBANGMII_MULTI
-/* I2C */
-#define CONFIG_SH_SH7734_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_SYS_MAX_I2C_BUS 2
-#define CONFIG_SYS_I2C_MODULE 0
-#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x50
-#define CONFIG_SH_I2C_DATA_HIGH 4
-#define CONFIG_SH_I2C_DATA_LOW 5
-#define CONFIG_SH_I2C_CLOCK 500000000
-#define CONFIG_SH_I2C_BASE0 0xFFC70000
-#define CONFIG_SH_I2C_BASE1 0xFFC71000
-
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h
index a4c7847dab..cce39f27c7 100644
--- a/include/configs/apx4devkit.h
+++ b/include/configs/apx4devkit.h
@@ -79,12 +79,6 @@
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
-/* RTC */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-#endif
-
/* Boot Linux */
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTCOMMAND "run bootcmd_nand"
diff --git a/include/configs/aria.h b/include/configs/aria.h
index 94f6605d46..4d946fc44a 100644
--- a/include/configs/aria.h
+++ b/include/configs/aria.h
@@ -340,31 +340,11 @@
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#endif
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
- * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-
/*
* Ethernet configuration
*/
@@ -392,7 +372,6 @@
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
diff --git a/include/configs/axs10x.h b/include/configs/axs10x.h
index 768e8fbfa4..66e8cd5e9a 100644
--- a/include/configs/axs10x.h
+++ b/include/configs/axs10x.h
@@ -100,7 +100,7 @@
/*
* Environment settings
*/
-#define CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE SZ_512
#define CONFIG_ENV_OFFSET 0
diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
index 0073cb5373..3a7d826837 100644
--- a/include/configs/cm5200.h
+++ b/include/configs/cm5200.h
@@ -44,7 +44,7 @@
/*
* POST support
*/
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU)
#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
/* List of I2C addresses to be verified by POST */
#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \
@@ -199,16 +199,6 @@
"2m(kernel),27904k(rootfs)," \
"-(config)"
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */
-#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */
-
/*
* RTC configuration
*/
diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h
index 2b56945dd9..ab546c50cd 100644
--- a/include/configs/digsy_mtc.h
+++ b/include/configs/digsy_mtc.h
@@ -85,7 +85,6 @@
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_PCI
@@ -205,36 +204,6 @@
#define CONFIG_BOOTCOMMAND "run mtcb_start"
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_MODULE 1
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#if defined(CONFIG_DIGSY_REV5)
-#define CONFIG_SYS_I2C_RTC_ADDR 0x56
-#define CONFIG_RTC_RV3029
-/* Enable 5k Ohm trickle charge resistor */
-#define CONFIG_SYS_RV3029_TCR 0x20
-#else
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */
-#endif
-
/*
* Flash configuration
*/
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
index 6b6bbbd5c0..7ffc9d1dd9 100644
--- a/include/configs/ids8313.h
+++ b/include/configs/ids8313.h
@@ -165,7 +165,6 @@
#define CONFIG_TSEC2
#define CONFIG_TSEC_ENET
#define CONFIG_HARD_SPI
-#define CONFIG_HARD_I2C
/*
* NOR FLASH setup
diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h
index aff4adf5d0..ece72c6aa1 100644
--- a/include/configs/ipek01.h
+++ b/include/configs/ipek01.h
@@ -150,29 +150,6 @@
#define OF_SOC "soc5200 at f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
#define CONFIG_SYS_FLASH_BASE 0xFC000000
#define CONFIG_SYS_FLASH_SIZE 0x01000000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h
index 0d97317c7f..4461623118 100644
--- a/include/configs/jupiter.h
+++ b/include/configs/jupiter.h
@@ -127,25 +127,6 @@
#define OF_STDOUT_PATH "/soc5200 at f0000000/serial at 2000"
#endif
-#if 0
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-#endif
-
/*
* Flash configuration
*/
diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
index f6fa599e6b..c4717238bb 100644
--- a/include/configs/m28evk.h
+++ b/include/configs/m28evk.h
@@ -16,7 +16,6 @@
/* U-Boot Commands */
#define CONFIG_FAT_WRITE
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NAND_TRIMFFS
@@ -63,11 +62,6 @@
#define CONFIG_FEC_MXC
#endif
-/* EEPROM */
-#ifdef CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#endif
-
/* RTC */
#ifdef CONFIG_CMD_DATE
/* Use the internal RTC in the MXS chip */
diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h
new file mode 100644
index 0000000000..68874dc029
--- /dev/null
+++ b/include/configs/manroland/mpc5200-common.h
@@ -0,0 +1,176 @@
+/*
+ * (C) Copyright 2009
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __MANROLAND_MPC52XX__COMMON_H
+#define __MANROLAND_MPC52XX__COMMON_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC5200 1 /* MPC5200 CPU */
+
+/* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\
+ 230400 }
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
+# define CONFIG_SYS_LOWBOOT 1
+#endif
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFF800000
+
+#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */
+#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */
+
+/* Settings for XLB = 132 MHz */
+#define SDRAM_DDR 1
+#define SDRAM_MODE 0x018D0000
+#define SDRAM_EMODE 0x40090000
+#define SDRAM_CONTROL 0x714f0f00
+#define SDRAM_CONFIG1 0x73722930
+#define SDRAM_CONFIG2 0x47770000
+#define SDRAM_TAPDELAY 0x10000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
+#else
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (192 << 10)
+#define CONFIG_SYS_MALLOC_LEN (512 << 10)
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+#define CONFIG_PHY_ADDR 0x00
+#define CONFIG_MII 1
+
+/*use Hardware WDT */
+#define CONFIG_HW_WATCHDOG
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+
+/* 8Mbit SRAM @0x80100000 */
+#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE
+
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+
+#define CONFIG_IDE_PREINIT 1
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#define CONFIG_ATAPI 1
+
+#define OF_CPU "PowerPC,5200 at 0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200 at f0000000/serial at 2000"
+#define CONFIG_OF_IDE_FIXUP
+
+#endif /* __MANROLAND_MPC52XX__COMMON_H */
diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h
index 1a9cb675df..fe94e663c5 100644
--- a/include/configs/mecp5123.h
+++ b/include/configs/mecp5123.h
@@ -241,26 +241,11 @@
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
-#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */
-
/*
* Ethernet configuration
*/
@@ -280,7 +265,7 @@
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */
+#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */
@@ -288,7 +273,6 @@
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index 136db0dd26..cb5c346807 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -34,7 +34,6 @@
* Command line configuration.
*/
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_JFFS2
@@ -255,21 +254,6 @@
#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
#define CONFIG_SYS_ATA_STRIDE 4
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
-
/*
* RTC configuration
*/
@@ -283,12 +267,6 @@
#define ENABLE_GPIO_OUT 0x00000024
#define LED_ON 0x00000010
-/*
- * Temperature sensor
- */
-#define CONFIG_DTT_LM75 1
-#define CONFIG_DTT_SENSORS { 0x49 }
-
/*
* Environment settings
*/
diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h
index dafb724e3f..f3961a6f35 100644
--- a/include/configs/mpc5121ads.h
+++ b/include/configs/mpc5121ads.h
@@ -327,28 +327,11 @@
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#endif
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
-
/*
* Ethernet configuration
*/
@@ -396,7 +379,6 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO
diff --git a/include/configs/mxs.h b/include/configs/mxs.h
index fdf596f82f..c403dda483 100644
--- a/include/configs/mxs.h
+++ b/include/configs/mxs.h
@@ -126,16 +126,6 @@
#endif
#endif
-/* I2C */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXS
-#define CONFIG_HARD_I2C
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED 400000
-#endif
-#endif
-
/* LCD */
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS
diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h
index e2881a7177..1b4200bcbf 100644
--- a/include/configs/o2dnt-common.h
+++ b/include/configs/o2dnt-common.h
@@ -68,7 +68,6 @@
/*
* Supported commands
*/
-#define CONFIG_CMD_EEPROM
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#endif
@@ -172,27 +171,6 @@
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration:
- *
- * O2DNT board is equiped with Ramtron FRAM device FM24CL16
- * 16 Kib Ferroelectric Nonvolatile serial RAM memory
- * organized as 2048 x 8 bits and addressable as eight I2C devices
- * 0x50 ... 0x57 each 256 bytes in size
- *
- */
-#define CONFIG_SYS_I2C_FRAM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
/*
* There is no write delay with FRAM, write operations are performed at bus
* speed. Thus, no status polling or write delay is needed.
diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h
index 6d8a2338a2..406f3e547a 100644
--- a/include/configs/pcm030.h
+++ b/include/configs/pcm030.h
@@ -49,7 +49,6 @@ Serial console configuration
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_PCI
@@ -120,31 +119,6 @@ IPB Bus clocking configuration.
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_XLB_PIPELINING 1
-/*---------------------------------------------------------------------------
- I2C configuration
----------------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*---------------------------------------------------------------------------
- EEPROM CAT24WC32 configuration
----------------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE 2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*---------------------------------------------------------------------------
-RTC configuration
----------------------------------------------------------------------------*/
-#define RTC
-#define CONFIG_RTC_PCF8563 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
/*---------------------------------------------------------------------------
Flash configuration
---------------------------------------------------------------------------*/
@@ -172,11 +146,10 @@ RTC configuration
Environment settings
---------------------------------------------------------------------------*/
-/* pcm030 ships with environment is EEPROM by default */
-#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
/*beginning of the EEPROM */
-#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
+#define CONFIG_ENV_SIZE 2048
#define CONFIG_ENV_OVERWRITE 1
diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h
index 501611dde7..4bd8236b33 100644
--- a/include/configs/pdm360ng.h
+++ b/include/configs/pdm360ng.h
@@ -301,34 +301,11 @@
#define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000
#define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */
-
-/*
- * MAC addr in EEPROM
- */
-#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10
/*
* Enabled only to delete "ethaddr" before testing
* "ethaddr" setting from EEPROM
@@ -344,12 +321,6 @@
#define CONFIG_FEC_AN_TIMEOUT 1
#define CONFIG_HAS_ETH0
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
/*
* Environment
*/
@@ -367,7 +338,6 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_REGINFO
#undef CONFIG_CMD_FUSE
diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h
index 642572fc95..b159b1ed8d 100644
--- a/include/configs/r0p7734.h
+++ b/include/configs/r0p7734.h
@@ -40,20 +40,6 @@
# define CONFIG_SMC911X_BASE (0x84000000)
#endif
-/* I2C */
-#define CONFIG_SH_SH7734_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_SYS_MAX_I2C_BUS 2
-#define CONFIG_SYS_I2C_MODULE 0
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x50
-#define CONFIG_SH_I2C_DATA_HIGH 4
-#define CONFIG_SH_I2C_DATA_LOW 5
-#define CONFIG_SH_I2C_CLOCK 500000000
-#define CONFIG_SH_I2C_BASE0 0xFFC70000
-#define CONFIG_SH_I2C_BASE1 0xFFC7100
-
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
diff --git a/include/configs/s32v234evb.h b/include/configs/s32v234evb.h
index 398b3aa343..33487cd86f 100644
--- a/include/configs/s32v234evb.h
+++ b/include/configs/s32v234evb.h
@@ -97,16 +97,6 @@
#define CONFIG_PHY_MICREL
#endif
-#if 0 /* Disable until the I2C driver will be updated */
-
-/* I2C Configs */
-#define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR
-#define CONFIG_SYS_I2C_SPEED 100000
-#endif
-
#if 0 /* Disable until the FLASH will be implemented */
#define CONFIG_SYS_USE_NAND
#endif
diff --git a/include/configs/v38b.h b/include/configs/v38b.h
index cc0007827d..0bc0ae517a 100644
--- a/include/configs/v38b.h
+++ b/include/configs/v38b.h
@@ -134,27 +134,6 @@
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
/*
* Flash configuration - use CFI driver
*/
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
2017-05-13 3:09 ` [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:23 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD Simon Glass
` (9 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option for powerpc.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
arch/powerpc/cpu/mpc512x/Makefile | 1 -
arch/powerpc/cpu/mpc512x/i2c.c | 386 -------------------
arch/powerpc/cpu/mpc5xxx/Makefile | 1 -
arch/powerpc/cpu/mpc5xxx/i2c.c | 456 ----------------------
arch/powerpc/cpu/mpc8260/Makefile | 2 +-
arch/powerpc/cpu/mpc8260/commproc.c | 4 -
arch/powerpc/cpu/mpc8260/i2c.c | 741 ------------------------------------
arch/powerpc/cpu/mpc8xx/Makefile | 1 -
arch/powerpc/cpu/mpc8xx/i2c.c | 672 --------------------------------
board/freescale/m52277evb/README | 1 -
board/freescale/m53017evb/README | 1 -
board/freescale/m5373evb/README | 1 -
board/freescale/m54455evb/README | 1 -
board/freescale/m547xevb/README | 1 -
14 files changed, 1 insertion(+), 2268 deletions(-)
delete mode 100644 arch/powerpc/cpu/mpc512x/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc5xxx/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc8260/i2c.c
delete mode 100644 arch/powerpc/cpu/mpc8xx/i2c.c
diff --git a/arch/powerpc/cpu/mpc512x/Makefile b/arch/powerpc/cpu/mpc512x/Makefile
index 98991c688b..933deebdae 100644
--- a/arch/powerpc/cpu/mpc512x/Makefile
+++ b/arch/powerpc/cpu/mpc512x/Makefile
@@ -9,7 +9,6 @@ obj-y := cpu.o
obj-y += traps.o
obj-y += cpu_init.o
obj-y += fixed_sdram.o
-obj-y += i2c.o
obj-y += interrupts.o
obj-y += iopin.o
obj-y += serial.o
diff --git a/arch/powerpc/cpu/mpc512x/i2c.c b/arch/powerpc/cpu/mpc512x/i2c.c
deleted file mode 100644
index 15d519a116..0000000000
--- a/arch/powerpc/cpu/mpc512x/i2c.c
+++ /dev/null
@@ -1,386 +0,0 @@
-/*
- * (C) Copyright 2003 - 2009
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Based on the MPC5xxx code.
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_HARD_I2C
-
-#include <i2c.h>
-
-/* by default set I2C bus 0 active */
-static unsigned int bus_num __attribute__ ((section (".data"))) = 0;
-
-#define I2C_TIMEOUT 100
-#define I2C_RETRIES 3
-
-struct mpc512x_i2c_tap {
- int scl2tap;
- int tap2tap;
-};
-
-static int mpc_reg_in(volatile u32 *reg);
-static void mpc_reg_out(volatile u32 *reg, int val, int mask);
-static int wait_for_bb(void);
-static int wait_for_pin(int *status);
-static int do_address(uchar chip, char rdwr_flag);
-static int send_bytes(uchar chip, char *buf, int len);
-static int receive_bytes(uchar chip, char *buf, int len);
-static int mpc_get_fdr(int);
-
-static int mpc_reg_in (volatile u32 *reg)
-{
- int ret = in_be32(reg) >> 24;
-
- return ret;
-}
-
-static void mpc_reg_out (volatile u32 *reg, int val, int mask)
-{
- if (!mask) {
- out_be32(reg, val << 24);
- } else {
- clrsetbits_be32(reg, mask << 24, (val & mask) << 24);
- }
-}
-
-static int wait_for_bb (void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int timeout = I2C_TIMEOUT;
- int status;
-
- status = mpc_reg_in (®s->msr);
-
- while (timeout-- && (status & I2C_BB)) {
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
- (void)mpc_reg_in(®s->mdr);
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- mpc_reg_out (®s->mcr, 0, 0);
- mpc_reg_out (®s->mcr, I2C_EN, 0);
-
- udelay (1000);
- status = mpc_reg_in (®s->msr);
- }
-
- return (status & I2C_BB);
-}
-
-static int wait_for_pin (int *status)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int timeout = I2C_TIMEOUT;
-
- *status = mpc_reg_in (®s->msr);
-
- while (timeout-- && !(*status & I2C_IF)) {
- udelay (1000);
- *status = mpc_reg_in (®s->msr);
- }
-
- if (!(*status & I2C_IF)) {
- return -1;
- }
-
- mpc_reg_out (®s->msr, 0, I2C_IF);
-
- return 0;
-}
-
-static int do_address (uchar chip, char rdwr_flag)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int status;
-
- chip <<= 1;
-
- if (rdwr_flag) {
- chip |= 1;
- }
-
- mpc_reg_out (®s->mcr, I2C_TX, I2C_TX);
- mpc_reg_out (®s->mdr, chip, 0);
-
- if (wait_for_pin (&status)) {
- return -2;
- }
-
- if (status & I2C_RXAK) {
- return -3;
- }
-
- return 0;
-}
-
-static int send_bytes (uchar chip, char *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int wrcount;
- int status;
-
- for (wrcount = 0; wrcount < len; ++wrcount) {
-
- mpc_reg_out (®s->mdr, buf[wrcount], 0);
-
- if (wait_for_pin (&status)) {
- break;
- }
-
- if (status & I2C_RXAK) {
- break;
- }
-
- }
-
- return !(wrcount == len);
-}
-
-static int receive_bytes (uchar chip, char *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int dummy = 1;
- int rdcount = 0;
- int status;
- int i;
-
- mpc_reg_out (®s->mcr, 0, I2C_TX);
-
- for (i = 0; i < len; ++i) {
- buf[rdcount] = mpc_reg_in (®s->mdr);
-
- if (dummy) {
- dummy = 0;
- } else {
- rdcount++;
- }
-
- if (wait_for_pin (&status)) {
- return -4;
- }
- }
-
- mpc_reg_out (®s->mcr, I2C_TXAK, I2C_TXAK);
- buf[rdcount++] = mpc_reg_in (®s->mdr);
-
- if (wait_for_pin (&status)) {
- return -5;
- }
-
- mpc_reg_out (®s->mcr, 0, I2C_TXAK);
-
- return 0;
-}
-
-/**************** I2C API ****************/
-
-void i2c_init (int speed, int saddr)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- int i;
-
- for (i = 0; i < I2C_BUS_CNT; i++){
- volatile i2c512x_dev_t *regs = &im->i2c.dev[i];
-
- mpc_reg_out (®s->mcr, 0, 0);
-
- /* Set clock */
- mpc_reg_out (®s->mfdr, mpc_get_fdr (speed), 0);
- mpc_reg_out (®s->madr, saddr << 1, 0);
-
- /* Enable module */
- mpc_reg_out (®s->mcr, I2C_EN, I2C_INIT_MASK);
- mpc_reg_out (®s->msr, 0, I2C_IF);
- }
-
- /* Disable interrupts */
- out_be32(&im->i2c.icr, 0);
-
- /* Turn off filters */
- out_be32(&im->i2c.mifr, 0);
-}
-
-static int mpc_get_fdr (int speed)
-{
- static int fdr = -1;
-
- if (fdr == -1) {
- ulong best_speed = 0;
- ulong divider;
- ulong ips, scl;
- ulong bestmatch = 0xffffffffUL;
- int best_i = 0, best_j = 0, i, j;
- int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8};
- struct mpc512x_i2c_tap scltap[] = {
- {4, 1},
- {4, 2},
- {6, 4},
- {6, 8},
- {14, 16},
- {30, 32},
- {62, 64},
- {126, 128}
- };
-
- ips = gd->arch.ips_clk;
- for (i = 7; i >= 0; i--) {
- for (j = 7; j >= 0; j--) {
- scl = 2 * (scltap[j].scl2tap +
- (SCL_Tap[i] - 1) * scltap[j].tap2tap
- + 2);
- if (ips <= speed*scl) {
- if ((speed*scl - ips) < bestmatch) {
- bestmatch = speed*scl - ips;
- best_i = i;
- best_j = j;
- best_speed = ips/scl;
- }
- }
- }
- }
- divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2);
- if (gd->flags & GD_FLG_RELOC) {
- fdr = divider;
- } else {
- debug("%ld kHz, \n", best_speed / 1000);
- return divider;
- }
- }
-
- return fdr;
-}
-
-int i2c_probe (uchar chip)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int i;
-
- for (i = 0; i < I2C_RETRIES; i++) {
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
-
- if (! do_address (chip, 0)) {
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- udelay (500);
- break;
- }
-
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- udelay (500);
- }
-
- return (i == I2C_RETRIES);
-}
-
-int i2c_read (uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- char xaddr[4];
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb ()) {
- printf ("i2c_read: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
- if (do_address (chip, 0)) {
- printf ("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes (chip, &xaddr[4-alen], alen)) {
- printf ("i2c_read: send_bytes failed\n");
- goto Done;
- }
-
- mpc_reg_out (®s->mcr, I2C_RSTA, I2C_RSTA);
- if (do_address (chip, 1)) {
- printf ("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (receive_bytes (chip, (char *)buf, len)) {
- printf ("i2c_read: receive_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-int i2c_write (uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- char xaddr[4];
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb ()) {
- printf ("i2c_write: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
- if (do_address (chip, 0)) {
- printf ("i2c_write: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes (chip, &xaddr[4-alen], alen)) {
- printf ("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- if (send_bytes (chip, (char *)buf, len)) {
- printf ("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-int i2c_set_bus_num (unsigned int bus)
-{
- if (bus >= I2C_BUS_CNT) {
- return -1;
- }
- bus_num = bus;
-
- return 0;
-}
-
-unsigned int i2c_get_bus_num (void)
-{
- return bus_num;
-}
-
-#endif /* CONFIG_HARD_I2C */
diff --git a/arch/powerpc/cpu/mpc5xxx/Makefile b/arch/powerpc/cpu/mpc5xxx/Makefile
index 5c67e1d37d..88e3b2e3ae 100644
--- a/arch/powerpc/cpu/mpc5xxx/Makefile
+++ b/arch/powerpc/cpu/mpc5xxx/Makefile
@@ -9,7 +9,6 @@ extra-y = start.o
extra-y += traps.o
obj-y += io.o
obj-y += firmware_sc_task_bestcomm.impl.o
-obj-y += i2c.o
obj-y += cpu.o
obj-y += cpu_init.o
obj-y += ide.o
diff --git a/arch/powerpc/cpu/mpc5xxx/i2c.c b/arch/powerpc/cpu/mpc5xxx/i2c.c
deleted file mode 100644
index 73601ae184..0000000000
--- a/arch/powerpc/cpu/mpc5xxx/i2c.c
+++ /dev/null
@@ -1,456 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_HARD_I2C
-
-#include <mpc5xxx.h>
-#include <i2c.h>
-
-#if !defined(CONFIG_I2C_MULTI_BUS)
-#if (CONFIG_SYS_I2C_MODULE == 2)
-#define I2C_BASE MPC5XXX_I2C2
-#elif (CONFIG_SYS_I2C_MODULE == 1)
-#define I2C_BASE MPC5XXX_I2C1
-#else
-#error CONFIG_SYS_I2C_MODULE is not properly configured
-#endif
-#else
-static unsigned int i2c_bus_num __attribute__ ((section (".data"))) =
- CONFIG_SYS_SPD_BUS_NUM;
-static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED,
- CONFIG_SYS_I2C_SPEED};
-
-static const unsigned long i2c_dev[2] = {
- MPC5XXX_I2C1,
- MPC5XXX_I2C2,
-};
-
-#define I2C_BASE ((struct mpc5xxx_i2c *)i2c_dev[i2c_bus_num])
-#endif
-
-#define I2C_TIMEOUT 6667
-#define I2C_RETRIES 3
-
-struct mpc5xxx_i2c_tap {
- int scl2tap;
- int tap2tap;
-};
-
-static int mpc_reg_in (volatile u32 *reg);
-static void mpc_reg_out (volatile u32 *reg, int val, int mask);
-static int wait_for_bb (void);
-static int wait_for_pin (int *status);
-static int do_address (uchar chip, char rdwr_flag);
-static int send_bytes (uchar chip, char *buf, int len);
-static int receive_bytes (uchar chip, char *buf, int len);
-static int mpc_get_fdr (int);
-
-static int mpc_reg_in(volatile u32 *reg)
-{
- int ret = *reg >> 24;
- __asm__ __volatile__ ("eieio");
- return ret;
-}
-
-static void mpc_reg_out(volatile u32 *reg, int val, int mask)
-{
- int tmp;
-
- if (!mask) {
- *reg = val << 24;
- } else {
- tmp = mpc_reg_in(reg);
- *reg = ((tmp & ~mask) | (val & mask)) << 24;
- }
- __asm__ __volatile__ ("eieio");
-
- return;
-}
-
-static int wait_for_bb(void)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int timeout = I2C_TIMEOUT;
- int status;
-
- status = mpc_reg_in(®s->msr);
-
- while (timeout-- && (status & I2C_BB)) {
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
- (void)mpc_reg_in(®s->mdr);
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- mpc_reg_out(®s->mcr, 0, 0);
- mpc_reg_out(®s->mcr, I2C_EN, 0);
- udelay(15);
- status = mpc_reg_in(®s->msr);
- }
-
- return (status & I2C_BB);
-}
-
-static int wait_for_pin(int *status)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int timeout = I2C_TIMEOUT;
-
- *status = mpc_reg_in(®s->msr);
-
- while (timeout-- && !(*status & I2C_IF)) {
- udelay(15);
- *status = mpc_reg_in(®s->msr);
- }
-
- if (!(*status & I2C_IF)) {
- return -1;
- }
-
- mpc_reg_out(®s->msr, 0, I2C_IF);
-
- return 0;
-}
-
-static int do_address(uchar chip, char rdwr_flag)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int status;
-
- chip <<= 1;
-
- if (rdwr_flag) {
- chip |= 1;
- }
-
- mpc_reg_out(®s->mcr, I2C_TX, I2C_TX);
- mpc_reg_out(®s->mdr, chip, 0);
-
- if (wait_for_pin(&status)) {
- return -2;
- }
-
- if (status & I2C_RXAK) {
- return -3;
- }
-
- return 0;
-}
-
-static int send_bytes(uchar chip, char *buf, int len)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int wrcount;
- int status;
-
- for (wrcount = 0; wrcount < len; ++wrcount) {
-
- mpc_reg_out(®s->mdr, buf[wrcount], 0);
-
- if (wait_for_pin(&status)) {
- break;
- }
-
- if (status & I2C_RXAK) {
- break;
- }
-
- }
-
- return !(wrcount == len);
-}
-
-static int receive_bytes(uchar chip, char *buf, int len)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int dummy = 1;
- int rdcount = 0;
- int status;
- int i;
-
- mpc_reg_out(®s->mcr, 0, I2C_TX);
-
- for (i = 0; i < len; ++i) {
- buf[rdcount] = mpc_reg_in(®s->mdr);
-
- if (dummy) {
- dummy = 0;
- } else {
- rdcount++;
- }
-
-
- if (wait_for_pin(&status)) {
- return -4;
- }
- }
-
- mpc_reg_out(®s->mcr, I2C_TXAK, I2C_TXAK);
- buf[rdcount++] = mpc_reg_in(®s->mdr);
-
- if (wait_for_pin(&status)) {
- return -5;
- }
-
- mpc_reg_out(®s->mcr, 0, I2C_TXAK);
-
- return 0;
-}
-
-#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
-
-#define FDR510(x) (u8) (((x & 0x20) >> 3) | (x & 0x3))
-#define FDR432(x) (u8) ((x & 0x1C) >> 2)
-/*
- * Reset any i2c devices that may have been interrupted during a system reset.
- * Normally this would be accomplished by clocking the line until SCL and SDA
- * are released and then sending a start condtiion (From an Atmel datasheet).
- * There is no direct access to the i2c pins so instead create start commands
- * through the i2c interface. Send a start command then delay for the SDA Hold
- * time, repeat this by disabling/enabling the bus a total of 9 times.
- */
-static void send_reset(void)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int i;
- u32 delay;
- u8 fdr;
- int SDA_Tap[] = { 3, 3, 4, 4, 1, 1, 2, 2};
- struct mpc5xxx_i2c_tap scltap[] = {
- {4, 1},
- {4, 2},
- {6, 4},
- {6, 8},
- {14, 16},
- {30, 32},
- {62, 64},
- {126, 128}
- };
-
- fdr = (u8)mpc_reg_in(®s->mfdr);
-
- delay = scltap[FDR432(fdr)].scl2tap + ((SDA_Tap[FDR510(fdr)] - 1) * \
- scltap[FDR432(fdr)].tap2tap) + 3;
-
- for (i = 0; i < 9; i++) {
- mpc_reg_out(®s->mcr, I2C_EN|I2C_STA|I2C_TX, I2C_INIT_MASK);
- udelay(delay);
- mpc_reg_out(®s->mcr, 0, I2C_INIT_MASK);
- udelay(delay);
- }
-
- mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK);
-}
-#endif /* CONFIG_SYS_I2c_INIT_MPC5XXX */
-
-/**************** I2C API ****************/
-
-void i2c_init(int speed, int saddr)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
-
- mpc_reg_out(®s->mcr, 0, 0);
- mpc_reg_out(®s->madr, saddr << 1, 0);
-
- /* Set clock
- */
- mpc_reg_out(®s->mfdr, mpc_get_fdr(speed), 0);
-
- /* Enable module
- */
- mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK);
- mpc_reg_out(®s->msr, 0, I2C_IF);
-
-#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
- send_reset();
-#endif
- return;
-}
-
-static int mpc_get_fdr(int speed)
-{
- static int fdr = -1;
-
- if (fdr == -1) {
- ulong best_speed = 0;
- ulong divider;
- ulong ipb, scl;
- ulong bestmatch = 0xffffffffUL;
- int best_i = 0, best_j = 0, i, j;
- int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8};
- struct mpc5xxx_i2c_tap scltap[] = {
- {4, 1},
- {4, 2},
- {6, 4},
- {6, 8},
- {14, 16},
- {30, 32},
- {62, 64},
- {126, 128}
- };
-
- ipb = gd->arch.ipb_clk;
- for (i = 7; i >= 0; i--) {
- for (j = 7; j >= 0; j--) {
- scl = 2 * (scltap[j].scl2tap +
- (SCL_Tap[i] - 1) * scltap[j].tap2tap + 2);
- if (ipb <= speed*scl) {
- if ((speed*scl - ipb) < bestmatch) {
- bestmatch = speed*scl - ipb;
- best_i = i;
- best_j = j;
- best_speed = ipb/scl;
- }
- }
- }
- }
- divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2);
- if (gd->flags & GD_FLG_RELOC) {
- fdr = divider;
- } else {
- printf("%ld kHz, ", best_speed / 1000);
- return divider;
- }
- }
-
- return fdr;
-}
-
-int i2c_probe(uchar chip)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int i;
-
- for (i = 0; i < I2C_RETRIES; i++) {
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
-
- if (! do_address(chip, 0)) {
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- udelay(500);
- break;
- }
-
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- udelay(500);
- }
-
- return (i == I2C_RETRIES);
-}
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- char xaddr[4];
- struct mpc5xxx_i2c * regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb()) {
- printf("i2c_read: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
- if (do_address(chip, 0)) {
- printf("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes(chip, &xaddr[4-alen], alen)) {
- printf("i2c_read: send_bytes failed\n");
- goto Done;
- }
-
- mpc_reg_out(®s->mcr, I2C_RSTA, I2C_RSTA);
- if (do_address(chip, 1)) {
- printf("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (receive_bytes(chip, (char *)buf, len)) {
- printf("i2c_read: receive_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- char xaddr[4];
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb()) {
- printf("i2c_write: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
- if (do_address(chip, 0)) {
- printf("i2c_write: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes(chip, &xaddr[4-alen], alen)) {
- printf("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- if (send_bytes(chip, (char *)buf, len)) {
- printf("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-#if defined(CONFIG_I2C_MULTI_BUS)
-int i2c_set_bus_num(unsigned int bus)
-{
- if (bus > 1)
- return -1;
-
- i2c_bus_num = bus;
- i2c_init(i2c_bus_speed[bus], CONFIG_SYS_I2C_SLAVE);
- return 0;
-}
-
-int i2c_set_bus_speed(unsigned int speed)
-{
- i2c_init(speed, CONFIG_SYS_I2C_SLAVE);
- return 0;
-}
-
-unsigned int i2c_get_bus_num(void)
-{
- return i2c_bus_num;
-}
-
-unsigned int i2c_get_bus_speed(void)
-{
- return i2c_bus_speed[i2c_bus_num];
-}
-#endif
-
-
-#endif /* CONFIG_HARD_I2C */
diff --git a/arch/powerpc/cpu/mpc8260/Makefile b/arch/powerpc/cpu/mpc8260/Makefile
index 83adc4c436..72dd8aba25 100644
--- a/arch/powerpc/cpu/mpc8260/Makefile
+++ b/arch/powerpc/cpu/mpc8260/Makefile
@@ -7,7 +7,7 @@
extra-y = start.o
obj-y = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
- interrupts.o ether_fcc.o i2c.o commproc.o \
+ interrupts.o ether_fcc.o commproc.o \
bedbug_603e.o pci.o spi.o kgdb.o
obj-$(CONFIG_ETHER_ON_SCC) += ether_scc.o
diff --git a/arch/powerpc/cpu/mpc8260/commproc.c b/arch/powerpc/cpu/mpc8260/commproc.c
index 484bd17745..ff69881089 100644
--- a/arch/powerpc/cpu/mpc8260/commproc.c
+++ b/arch/powerpc/cpu/mpc8260/commproc.c
@@ -41,10 +41,6 @@ m8260_cpm_reset(void)
do { /* Spin until command processed */
__asm__ __volatile__ ("eieio");
} while ((immr->im_cpm.cp_cpcr & CPM_CR_FLG) && ++count < 1000000);
-
-#ifdef CONFIG_HARD_I2C
- immr->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = 0;
-#endif
}
/* Allocate some memory from the dual ported ram.
diff --git a/arch/powerpc/cpu/mpc8260/i2c.c b/arch/powerpc/cpu/mpc8260/i2c.c
deleted file mode 100644
index a0de101329..0000000000
--- a/arch/powerpc/cpu/mpc8260/i2c.c
+++ /dev/null
@@ -1,741 +0,0 @@
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio at tin.it
- *
- * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <console.h>
-
-#if defined(CONFIG_HARD_I2C)
-
-#include <asm/cpm_8260.h>
-#include <i2c.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_I2C_MULTI_BUS)
-static unsigned int i2c_bus_num __attribute__ ((section(".data"))) = 0;
-#endif /* CONFIG_I2C_MULTI_BUS */
-
-/* uSec to wait between polls of the i2c */
-#define DELAY_US 100
-/* uSec to wait for the CPM to start processing the buffer */
-#define START_DELAY_US 1000
-
-/*
- * tx/rx per-byte timeout: we delay DELAY_US uSec between polls so the
- * timeout will be (tx_length + rx_length) * DELAY_US * TOUT_LOOP
- */
-#define TOUT_LOOP 5
-
-/*
- * Set default values
- */
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED 50000
-#endif
-
-
-typedef void (*i2c_ecb_t) (int, int, void *); /* error callback function */
-
-/* This structure keeps track of the bd and buffer space usage. */
-typedef struct i2c_state {
- int rx_idx; /* index to next free Rx BD */
- int tx_idx; /* index to next free Tx BD */
- void *rxbd; /* pointer to next free Rx BD */
- void *txbd; /* pointer to next free Tx BD */
- int tx_space; /* number of Tx bytes left */
- unsigned char *tx_buf; /* pointer to free Tx area */
- i2c_ecb_t err_cb; /* error callback function */
- void *cb_data; /* private data to be passed */
-} i2c_state_t;
-
-/* flags for i2c_send() and i2c_receive() */
-#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */
-#define I2CF_START_COND 0x02 /* tx: generate start condition */
-#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */
-
-/* return codes */
-#define I2CERR_NO_BUFFERS 1 /* no more BDs or buffer space */
-#define I2CERR_MSG_TOO_LONG 2 /* tried to send/receive to much data */
-#define I2CERR_TIMEOUT 3 /* timeout in i2c_doio() */
-#define I2CERR_QUEUE_EMPTY 4 /* i2c_doio called without send/rcv */
-#define I2CERR_IO_ERROR 5 /* had an error during comms */
-
-/* error callback flags */
-#define I2CECB_RX_ERR 0x10 /* this is a receive error */
-#define I2CECB_RX_OV 0x02 /* receive overrun error */
-#define I2CECB_RX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TX_ERR 0x20 /* this is a transmit error */
-#define I2CECB_TX_CL 0x01 /* transmit collision error */
-#define I2CECB_TX_UN 0x02 /* transmit underflow error */
-#define I2CECB_TX_NAK 0x04 /* transmit no ack error */
-#define I2CECB_TX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */
-
-#define ERROR_I2C_NONE 0
-#define ERROR_I2C_LENGTH 1
-
-#define I2C_WRITE_BIT 0x00
-#define I2C_READ_BIT 0x01
-
-#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
-
-
-#define NUM_RX_BDS 4
-#define NUM_TX_BDS 4
-#define MAX_TX_SPACE 256
-
-typedef struct I2C_BD {
- unsigned short status;
- unsigned short length;
- unsigned char *addr;
-} I2C_BD;
-
-#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */
-
-#define BD_I2C_TX_CL 0x0001 /* collision error */
-#define BD_I2C_TX_UN 0x0002 /* underflow error */
-#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */
-#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL)
-
-#define BD_I2C_RX_ERR BD_SC_OV
-
-/*
- * Returns the best value of I2BRG to meet desired clock speed of I2C with
- * input parameters (clock speed, filter, and predivider value).
- * It returns computer speed value and the difference between it and desired
- * speed.
- */
-static inline int
-i2c_roundrate(int hz, int speed, int filter, int modval,
- int *brgval, int *totspeed)
-{
- int moddiv = 1 << (5 - (modval & 3)), brgdiv, div;
-
- debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n",
- hz, speed, filter, modval);
-
- div = moddiv * speed;
- brgdiv = (hz + div - 1) / div;
-
- debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv);
-
- *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter);
-
- if ((*brgval < 0) || (*brgval > 255)) {
- debug("\t\trejected brgval=%d\n", *brgval);
- return -1;
- }
-
- brgdiv = 2 * (*brgval + 3 + (2 * filter));
- div = moddiv * brgdiv;
- *totspeed = hz / div;
-
- debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed);
-
- return 0;
-}
-
-/*
- * Sets the I2C clock predivider and divider to meet required clock speed.
- */
-static int i2c_setrate(int hz, int speed)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
- int brgval,
- modval, /* 0-3 */
- bestspeed_diff = speed,
- bestspeed_brgval = 0,
- bestspeed_modval = 0,
- bestspeed_filter = 0,
- totspeed,
- filter = 0; /* Use this fixed value */
-
- for (modval = 0; modval < 4; modval++) {
- if (i2c_roundrate(hz, speed, filter, modval, &brgval, &totspeed)
- == 0) {
- int diff = speed - totspeed;
-
- if ((diff >= 0) && (diff < bestspeed_diff)) {
- bestspeed_diff = diff;
- bestspeed_modval = modval;
- bestspeed_brgval = brgval;
- bestspeed_filter = filter;
- }
- }
- }
-
- debug("[I2C] Best is:\n");
- debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n",
- hz, speed, bestspeed_filter, bestspeed_modval, bestspeed_brgval,
- bestspeed_diff);
-
- i2c->i2c_i2mod |= ((bestspeed_modval & 3) << 1) |
- (bestspeed_filter << 3);
- i2c->i2c_i2brg = bestspeed_brgval & 0xff;
-
- debug("[I2C] i2mod=%08x i2brg=%08x\n", i2c->i2c_i2mod,
- i2c->i2c_i2brg);
-
- return 1;
-}
-
-void i2c_init(int speed, int slaveadd)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8260_t *cp = (cpm8260_t *)&immap->im_cpm;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
- volatile iic_t *iip;
- ulong rbase, tbase;
- volatile I2C_BD *rxbd, *txbd;
- uint dpaddr;
-
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
- /*
- * call board specific i2c bus reset routine before accessing the
- * environment, which might be in a chip on that bus. For details
- * about this problem see doc/I2C_Edge_Conditions.
- */
- i2c_init_board();
-#endif
-
- dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
- if (dpaddr == 0) {
- /* need to allocate dual port ram */
- dpaddr = m8260_cpm_dpalloc(64 +
- (NUM_RX_BDS * sizeof(I2C_BD)) +
- (NUM_TX_BDS * sizeof(I2C_BD)) +
- MAX_TX_SPACE, 64);
- immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] =
- dpaddr;
- }
-
- /*
- * initialise data in dual port ram:
- *
- * dpaddr -> parameter ram (64 bytes)
- * rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes)
- * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes)
- * tx buffer (MAX_TX_SPACE bytes)
- */
-
- iip = (iic_t *)&immap->im_dprambase[dpaddr];
- memset((void *)iip, 0, sizeof(iic_t));
-
- rbase = dpaddr + 64;
- tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD);
-
- /* Disable interrupts */
- i2c->i2c_i2mod = 0x00;
- i2c->i2c_i2cmr = 0x00;
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2add = slaveadd;
-
- /*
- * Set the I2C BRG Clock division factor from desired i2c rate
- * and current CPU rate (we assume sccr dfbgr field is 0;
- * divide BRGCLK by 1)
- */
- debug("[I2C] Setting rate...\n");
- i2c_setrate(gd->arch.brg_clk, CONFIG_SYS_I2C_SPEED);
-
- /* Set I2C controller in master mode */
- i2c->i2c_i2com = 0x01;
-
- /* Initialize Tx/Rx parameters */
- iip->iic_rbase = rbase;
- iip->iic_tbase = tbase;
- rxbd = (I2C_BD *)((unsigned char *) &immap->
- im_dprambase[iip->iic_rbase]);
- txbd = (I2C_BD *)((unsigned char *) &immap->
- im_dprambase[iip->iic_tbase]);
-
- debug("[I2C] rbase = %04x\n", iip->iic_rbase);
- debug("[I2C] tbase = %04x\n", iip->iic_tbase);
- debug("[I2C] rxbd = %08x\n", (int) rxbd);
- debug("[I2C] txbd = %08x\n", (int) txbd);
-
- /* Set big endian byte order */
- iip->iic_tfcr = 0x10;
- iip->iic_rfcr = 0x10;
-
- /* Set maximum receive size. */
- iip->iic_mrblr = I2C_RXTX_LEN;
-
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_I2C_PAGE,
- CPM_CR_I2C_SBLOCK,
- 0x00, CPM_CR_INIT_TRX) | CPM_CR_FLG;
- do {
- __asm__ __volatile__("eieio");
- } while (cp->cp_cpcr & CPM_CR_FLG);
-
- /* Clear events and interrupts */
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2cmr = 0x00;
-}
-
-static
-void i2c_newio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile iic_t *iip;
- uint dpaddr;
-
- debug("[I2C] i2c_newio\n");
-
- dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
- iip = (iic_t *)&immap->im_dprambase[dpaddr];
- state->rx_idx = 0;
- state->tx_idx = 0;
- state->rxbd = (void *)&immap->im_dprambase[iip->iic_rbase];
- state->txbd = (void *)&immap->im_dprambase[iip->iic_tbase];
- state->tx_space = MAX_TX_SPACE;
- state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD);
- state->err_cb = NULL;
- state->cb_data = NULL;
-
- debug("[I2C] rxbd = %08x\n", (int)state->rxbd);
- debug("[I2C] txbd = %08x\n", (int)state->txbd);
- debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf);
-
- /* clear the buffer memory */
- memset((char *) state->tx_buf, 0, MAX_TX_SPACE);
-}
-
-static
-int i2c_send(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags, unsigned short size, unsigned char *dataout)
-{
- volatile I2C_BD *txbd;
- int i, j;
-
- debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n",
- address, secondary_address, flags, size);
-
- /* trying to send message larger than BD */
- if (size > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size))
- return I2CERR_NO_BUFFERS;
-
- txbd = (I2C_BD *)state->txbd;
- txbd->addr = state->tx_buf;
-
- debug("[I2C] txbd = %08x\n", (int) txbd);
-
- if (flags & I2CF_START_COND) {
- debug("[I2C] Formatting addresses...\n");
- if (flags & I2CF_ENABLE_SECONDARY) {
- /* Length of message plus dest addresses */
- txbd->length = size + 2;
- txbd->addr[0] = address << 1;
- txbd->addr[1] = secondary_address;
- i = 2;
- } else {
- /* Length of message plus dest address */
- txbd->length = size + 1;
- /* Write destination address to BD */
- txbd->addr[0] = address << 1;
- i = 1;
- }
- } else {
- txbd->length = size; /* Length of message */
- i = 0;
- }
-
- /* set up txbd */
- txbd->status = BD_SC_READY;
- if (flags & I2CF_START_COND)
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND)
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
-
- /* Copy data to send into buffer */
- debug("[I2C] copy data...\n");
- for (j = 0; j < size; i++, j++)
- txbd->addr[i] = dataout[j];
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
-
- return 0;
-}
-
-static
-int i2c_receive(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags,
- unsigned short size_to_expect, unsigned char *datain)
-{
- volatile I2C_BD *rxbd, *txbd;
-
- debug("[I2C] i2c_receive %02d %02d %02d\n", address,
- secondary_address, flags);
-
- /* Expected to receive too much */
- if (size_to_expect > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS
- || state->tx_space < 2)
- return I2CERR_NO_BUFFERS;
-
- rxbd = (I2C_BD *) state->rxbd;
- txbd = (I2C_BD *) state->txbd;
-
- debug("[I2C] rxbd = %08x\n", (int) rxbd);
- debug("[I2C] txbd = %08x\n", (int) txbd);
-
- txbd->addr = state->tx_buf;
-
- /* set up TXBD for destination address */
- if (flags & I2CF_ENABLE_SECONDARY) {
- txbd->length = 2;
- txbd->addr[0] = address << 1; /* Write data */
- txbd->addr[1] = secondary_address; /* Internal address */
- txbd->status = BD_SC_READY;
- } else {
- txbd->length = 1 + size_to_expect;
- txbd->addr[0] = (address << 1) | 0x01;
- txbd->status = BD_SC_READY;
- memset(&txbd->addr[1], 0, txbd->length);
- }
-
- /* set up rxbd for reception */
- rxbd->status = BD_SC_EMPTY;
- rxbd->length = size_to_expect;
- rxbd->addr = datain;
-
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND) {
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
- rxbd->status |= BD_SC_WRAP;
- }
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]);
- debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- rxbd->length, rxbd->status, rxbd->addr[0], rxbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
- state->rx_idx++;
- state->rxbd = (void *) (rxbd + 1);
-
- return 0;
-}
-
-
-static
-int i2c_doio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile iic_t *iip;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
- volatile I2C_BD *txbd, *rxbd;
- int n, i, b, rxcnt = 0, rxtimeo = 0, txcnt = 0, txtimeo = 0, rc = 0;
- uint dpaddr;
-
- debug("[I2C] i2c_doio\n");
-
- if (state->tx_idx <= 0 && state->rx_idx <= 0) {
- debug("[I2C] No I/O is queued\n");
- return I2CERR_QUEUE_EMPTY;
- }
-
- dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
- iip = (iic_t *)&immap->im_dprambase[dpaddr];
- iip->iic_rbptr = iip->iic_rbase;
- iip->iic_tbptr = iip->iic_tbase;
-
- /* Enable I2C */
- debug("[I2C] Enabling I2C...\n");
- i2c->i2c_i2mod |= 0x01;
-
- /* Begin transmission */
- i2c->i2c_i2com |= 0x80;
-
- /* Loop until transmit & receive completed */
-
- n = state->tx_idx;
-
- if (n > 0) {
-
- txbd = ((I2C_BD *) state->txbd) - n;
- for (i = 0; i < n; i++) {
- txtimeo += TOUT_LOOP * txbd->length;
- txbd++;
- }
-
- txbd--; /* wait until last in list is done */
-
- debug("[I2C] Transmitting...(txbd=0x%08lx)\n",
- (ulong) txbd);
-
- udelay(START_DELAY_US); /* give it time to start */
- while ((txbd->status & BD_SC_READY) && (++txcnt < txtimeo)) {
- udelay(DELAY_US);
- if (ctrlc())
- return -1;
- __asm__ __volatile__("eieio");
- }
- }
-
- n = state->rx_idx;
-
- if (txcnt < txtimeo && n > 0) {
-
- rxbd = ((I2C_BD *) state->rxbd) - n;
- for (i = 0; i < n; i++) {
- rxtimeo += TOUT_LOOP * rxbd->length;
- rxbd++;
- }
-
- rxbd--; /* wait until last in list is done */
-
- debug("[I2C] Receiving...(rxbd=0x%08lx)\n", (ulong) rxbd);
-
- udelay(START_DELAY_US); /* give it time to start */
- while ((rxbd->status & BD_SC_EMPTY) && (++rxcnt < rxtimeo)) {
- udelay(DELAY_US);
- if (ctrlc())
- return -1;
- __asm__ __volatile__("eieio");
- }
- }
-
- /* Turn off I2C */
- i2c->i2c_i2mod &= ~0x01;
-
- n = state->tx_idx;
-
- if (n > 0) {
- for (i = 0; i < n; i++) {
- txbd = ((I2C_BD *) state->txbd) - (n - i);
- b = txbd->status & BD_I2C_TX_ERR;
- if (b != 0) {
- if (state->err_cb != NULL)
- (*state->err_cb) (I2CECB_TX_ERR | b,
- i, state->cb_data);
- if (rc == 0)
- rc = I2CERR_IO_ERROR;
- }
- }
- }
-
- n = state->rx_idx;
-
- if (n > 0) {
- for (i = 0; i < n; i++) {
- rxbd = ((I2C_BD *) state->rxbd) - (n - i);
- b = rxbd->status & BD_I2C_RX_ERR;
- if (b != 0) {
- if (state->err_cb != NULL)
- (*state->err_cb) (I2CECB_RX_ERR | b,
- i, state->cb_data);
- if (rc == 0)
- rc = I2CERR_IO_ERROR;
- }
- }
- }
-
- if ((txtimeo > 0 && txcnt >= txtimeo) ||
- (rxtimeo > 0 && rxcnt >= rxtimeo)) {
- if (state->err_cb != NULL)
- (*state->err_cb) (I2CECB_TIMEOUT, -1, state->cb_data);
- if (rc == 0)
- rc = I2CERR_TIMEOUT;
- }
-
- return rc;
-}
-
-static void i2c_probe_callback(int flags, int xnum, void *data)
-{
- /*
- * the only acceptable errors are a transmit NAK or a receive
- * overrun - tx NAK means the device does not exist, rx OV
- * means the device must have responded to the slave address
- * even though the transfer failed
- */
- if (flags == (I2CECB_TX_ERR | I2CECB_TX_NAK))
- *(int *) data |= 1;
- if (flags == (I2CECB_RX_ERR | I2CECB_RX_OV))
- *(int *) data |= 2;
-}
-
-int i2c_probe(uchar chip)
-{
- i2c_state_t state;
- int rc, err_flag;
- uchar buf[1];
-
- i2c_newio(&state);
-
- state.err_cb = i2c_probe_callback;
- state.cb_data = (void *) &err_flag;
- err_flag = 0;
-
- rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1,
- buf);
-
- if (rc != 0)
- return rc; /* probe failed */
-
- rc = i2c_doio(&state);
-
- if (rc == 0)
- return 0; /* device exists - read succeeded */
-
- if (rc == I2CERR_TIMEOUT)
- return -1; /* device does not exist - timeout */
-
- if (rc != I2CERR_IO_ERROR || err_flag == 0)
- return rc; /* probe failed */
-
- if (err_flag & 1)
- return -1; /* device does not exist - had transmit NAK */
-
- return 0; /* device exists - had receive overrun */
-}
-
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones
- * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address
- * and the extra bits end up in the "chip address" bit slots.
- * This makes a 24WC08 (1Kbyte) chip look like four 256 byte
- * chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_read: i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_read: i2c_receive failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_read: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones
- * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address
- * and the extra bits end up in the "chip address" bit slots.
- * This makes a 24WC08 (1Kbyte) chip look like four 256 byte
- * chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_write: first i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_write: second i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_write: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-#if defined(CONFIG_I2C_MULTI_BUS)
-/*
- * Functions for multiple I2C bus handling
- */
-unsigned int i2c_get_bus_num(void)
-{
- return i2c_bus_num;
-}
-
-int i2c_set_bus_num(unsigned int bus)
-{
- if (bus >= CONFIG_SYS_MAX_I2C_BUS)
- return -1;
- i2c_bus_num = bus;
- return 0;
-}
-
-#endif /* CONFIG_I2C_MULTI_BUS */
-#endif /* CONFIG_HARD_I2C */
diff --git a/arch/powerpc/cpu/mpc8xx/Makefile b/arch/powerpc/cpu/mpc8xx/Makefile
index 6f81fee571..fc91a054f0 100644
--- a/arch/powerpc/cpu/mpc8xx/Makefile
+++ b/arch/powerpc/cpu/mpc8xx/Makefile
@@ -14,7 +14,6 @@ obj-y += cpu.o
obj-y += cpu_init.o
obj-y += fec.o
obj-$(CONFIG_OF_LIBFDT) += fdt.o
-obj-y += i2c.o
obj-y += interrupts.o
obj-y += scc.o
obj-y += serial.o
diff --git a/arch/powerpc/cpu/mpc8xx/i2c.c b/arch/powerpc/cpu/mpc8xx/i2c.c
deleted file mode 100644
index 54d5cb5130..0000000000
--- a/arch/powerpc/cpu/mpc8xx/i2c.c
+++ /dev/null
@@ -1,672 +0,0 @@
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio at tin.it
- *
- * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Back ported to the 8xx platform (from the 8260 platform) by
- * Murray.Jensen at cmst.csiro.au, 27-Jan-01.
- */
-
-#include <common.h>
-#include <console.h>
-
-#ifdef CONFIG_HARD_I2C
-
-#include <commproc.h>
-#include <i2c.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* tx/rx timeout (we need the i2c early, so we don't use get_timer()) */
-#define TOUT_LOOP 1000000
-
-#define NUM_RX_BDS 4
-#define NUM_TX_BDS 4
-#define MAX_TX_SPACE 256
-#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
-
-typedef struct I2C_BD {
- unsigned short status;
- unsigned short length;
- unsigned char *addr;
-} I2C_BD;
-
-#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */
-
-#define BD_I2C_TX_CL 0x0001 /* collision error */
-#define BD_I2C_TX_UN 0x0002 /* underflow error */
-#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */
-#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL)
-
-#define BD_I2C_RX_ERR BD_SC_OV
-
-typedef void (*i2c_ecb_t) (int, int); /* error callback function */
-
-/* This structure keeps track of the bd and buffer space usage. */
-typedef struct i2c_state {
- int rx_idx; /* index to next free Rx BD */
- int tx_idx; /* index to next free Tx BD */
- void *rxbd; /* pointer to next free Rx BD */
- void *txbd; /* pointer to next free Tx BD */
- int tx_space; /* number of Tx bytes left */
- unsigned char *tx_buf; /* pointer to free Tx area */
- i2c_ecb_t err_cb; /* error callback function */
-} i2c_state_t;
-
-
-/* flags for i2c_send() and i2c_receive() */
-#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */
-#define I2CF_START_COND 0x02 /* tx: generate start condition */
-#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */
-
-/* return codes */
-#define I2CERR_NO_BUFFERS 0x01 /* no more BDs or buffer space */
-#define I2CERR_MSG_TOO_LONG 0x02 /* tried to send/receive to much data */
-#define I2CERR_TIMEOUT 0x03 /* timeout in i2c_doio() */
-#define I2CERR_QUEUE_EMPTY 0x04 /* i2c_doio called without send/receive */
-
-/* error callback flags */
-#define I2CECB_RX_ERR 0x10 /* this is a receive error */
-#define I2CECB_RX_ERR_OV 0x02 /* receive overrun error */
-#define I2CECB_RX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TX_ERR 0x20 /* this is a transmit error */
-#define I2CECB_TX_CL 0x01 /* transmit collision error */
-#define I2CECB_TX_UN 0x02 /* transmit underflow error */
-#define I2CECB_TX_NAK 0x04 /* transmit no ack error */
-#define I2CECB_TX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */
-
-/*
- * Returns the best value of I2BRG to meet desired clock speed of I2C with
- * input parameters (clock speed, filter, and predivider value).
- * It returns computer speed value and the difference between it and desired
- * speed.
- */
-static inline int
-i2c_roundrate(int hz, int speed, int filter, int modval,
- int *brgval, int *totspeed)
-{
- int moddiv = 1 << (5 - (modval & 3)), brgdiv, div;
-
- debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n",
- hz, speed, filter, modval);
-
- div = moddiv * speed;
- brgdiv = (hz + div - 1) / div;
-
- debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv);
-
- *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter);
-
- if ((*brgval < 0) || (*brgval > 255)) {
- debug("\t\trejected brgval=%d\n", *brgval);
- return -1;
- }
-
- brgdiv = 2 * (*brgval + 3 + (2 * filter));
- div = moddiv * brgdiv;
- *totspeed = hz / div;
-
- debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed);
-
- return 0;
-}
-
-/*
- * Sets the I2C clock predivider and divider to meet required clock speed.
- */
-static int i2c_setrate(int hz, int speed)
-{
- immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c8xx_t *i2c = (i2c8xx_t *) & immap->im_i2c;
- int brgval,
- modval, /* 0-3 */
- bestspeed_diff = speed,
- bestspeed_brgval = 0,
- bestspeed_modval = 0,
- bestspeed_filter = 0,
- totspeed,
- filter = 0; /* Use this fixed value */
-
- for (modval = 0; modval < 4; modval++) {
- if (i2c_roundrate
- (hz, speed, filter, modval, &brgval, &totspeed) == 0) {
- int diff = speed - totspeed;
-
- if ((diff >= 0) && (diff < bestspeed_diff)) {
- bestspeed_diff = diff;
- bestspeed_modval = modval;
- bestspeed_brgval = brgval;
- bestspeed_filter = filter;
- }
- }
- }
-
- debug("[I2C] Best is:\n");
- debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n",
- hz,
- speed,
- bestspeed_filter,
- bestspeed_modval,
- bestspeed_brgval,
- bestspeed_diff);
-
- i2c->i2c_i2mod |=
- ((bestspeed_modval & 3) << 1) | (bestspeed_filter << 3);
- i2c->i2c_i2brg = bestspeed_brgval & 0xff;
-
- debug("[I2C] i2mod=%08x i2brg=%08x\n",
- i2c->i2c_i2mod,
- i2c->i2c_i2brg);
-
- return 1;
-}
-
-void i2c_init(int speed, int slaveaddr)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
- volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
- volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
- ulong rbase, tbase;
- volatile I2C_BD *rxbd, *txbd;
- uint dpaddr;
-
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
- /* call board specific i2c bus reset routine before accessing the */
- /* environment, which might be in a chip on that bus. For details */
- /* about this problem see doc/I2C_Edge_Conditions. */
- i2c_init_board();
-#endif
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#else
- /* Disable relocation */
- iip->iic_rpbase = 0;
-#endif
-
- dpaddr = CPM_I2C_BASE;
-
- /*
- * initialise data in dual port ram:
- *
- * dpaddr->rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes)
- * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes)
- * tx buffer (MAX_TX_SPACE bytes)
- */
-
- rbase = dpaddr;
- tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD);
-
- /* Initialize Port B I2C pins. */
- cp->cp_pbpar |= 0x00000030;
- cp->cp_pbdir |= 0x00000030;
- cp->cp_pbodr |= 0x00000030;
-
- /* Disable interrupts */
- i2c->i2c_i2mod = 0x00;
- i2c->i2c_i2cmr = 0x00;
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2add = slaveaddr;
-
- /*
- * Set the I2C BRG Clock division factor from desired i2c rate
- * and current CPU rate (we assume sccr dfbgr field is 0;
- * divide BRGCLK by 1)
- */
- debug("[I2C] Setting rate...\n");
- i2c_setrate(gd->cpu_clk, CONFIG_SYS_I2C_SPEED);
-
- /* Set I2C controller in master mode */
- i2c->i2c_i2com = 0x01;
-
- /* Set SDMA bus arbitration level to 5 (SDCR) */
- immap->im_siu_conf.sc_sdcr = 0x0001;
-
- /* Initialize Tx/Rx parameters */
- iip->iic_rbase = rbase;
- iip->iic_tbase = tbase;
- rxbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_rbase]);
- txbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_tbase]);
-
- debug("[I2C] rbase = %04x\n", iip->iic_rbase);
- debug("[I2C] tbase = %04x\n", iip->iic_tbase);
- debug("[I2C] rxbd = %08x\n", (int)rxbd);
- debug("[I2C] txbd = %08x\n", (int)txbd);
-
- /* Set big endian byte order */
- iip->iic_tfcr = 0x10;
- iip->iic_rfcr = 0x10;
-
- /* Set maximum receive size. */
- iip->iic_mrblr = I2C_RXTX_LEN;
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- /*
- * Initialize required parameters if using microcode patch.
- */
- iip->iic_rbptr = iip->iic_rbase;
- iip->iic_tbptr = iip->iic_tbase;
- iip->iic_rstate = 0;
- iip->iic_tstate = 0;
-#else
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG;
- do {
- __asm__ __volatile__("eieio");
- } while (cp->cp_cpcr & CPM_CR_FLG);
-#endif
-
- /* Clear events and interrupts */
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2cmr = 0x00;
-}
-
-static void i2c_newio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
- volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-
- debug("[I2C] i2c_newio\n");
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
- state->rx_idx = 0;
- state->tx_idx = 0;
- state->rxbd = (void *)&cp->cp_dpmem[iip->iic_rbase];
- state->txbd = (void *)&cp->cp_dpmem[iip->iic_tbase];
- state->tx_space = MAX_TX_SPACE;
- state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD);
- state->err_cb = NULL;
-
- debug("[I2C] rxbd = %08x\n", (int)state->rxbd);
- debug("[I2C] txbd = %08x\n", (int)state->txbd);
- debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf);
-
- /* clear the buffer memory */
- memset((char *)state->tx_buf, 0, MAX_TX_SPACE);
-}
-
-static int
-i2c_send(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags, unsigned short size, unsigned char *dataout)
-{
- volatile I2C_BD *txbd;
- int i, j;
-
- debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n",
- address, secondary_address, flags, size);
-
- /* trying to send message larger than BD */
- if (size > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size))
- return I2CERR_NO_BUFFERS;
-
- txbd = (I2C_BD *) state->txbd;
- txbd->addr = state->tx_buf;
-
- debug("[I2C] txbd = %08x\n", (int)txbd);
-
- if (flags & I2CF_START_COND) {
- debug("[I2C] Formatting addresses...\n");
- if (flags & I2CF_ENABLE_SECONDARY) {
- /* Length of msg + dest addr */
- txbd->length = size + 2;
-
- txbd->addr[0] = address << 1;
- txbd->addr[1] = secondary_address;
- i = 2;
- } else {
- /* Length of msg + dest addr */
- txbd->length = size + 1;
- /* Write dest addr to BD */
- txbd->addr[0] = address << 1;
- i = 1;
- }
- } else {
- txbd->length = size; /* Length of message */
- i = 0;
- }
-
- /* set up txbd */
- txbd->status = BD_SC_READY;
- if (flags & I2CF_START_COND)
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND)
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
-
- /* Copy data to send into buffer */
- debug("[I2C] copy data...\n");
- for(j = 0; j < size; i++, j++)
- txbd->addr[i] = dataout[j];
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length,
- txbd->status,
- txbd->addr[0],
- txbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
-
- return 0;
-}
-
-static int
-i2c_receive(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags,
- unsigned short size_to_expect, unsigned char *datain)
-{
- volatile I2C_BD *rxbd, *txbd;
-
- debug("[I2C] i2c_receive %02d %02d %02d\n",
- address, secondary_address, flags);
-
- /* Expected to receive too much */
- if (size_to_expect > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS
- || state->tx_space < 2)
- return I2CERR_NO_BUFFERS;
-
- rxbd = (I2C_BD *) state->rxbd;
- txbd = (I2C_BD *) state->txbd;
-
- debug("[I2C] rxbd = %08x\n", (int)rxbd);
- debug("[I2C] txbd = %08x\n", (int)txbd);
-
- txbd->addr = state->tx_buf;
-
- /* set up TXBD for destination address */
- if (flags & I2CF_ENABLE_SECONDARY) {
- txbd->length = 2;
- txbd->addr[0] = address << 1; /* Write data */
- txbd->addr[1] = secondary_address; /* Internal address */
- txbd->status = BD_SC_READY;
- } else {
- txbd->length = 1 + size_to_expect;
- txbd->addr[0] = (address << 1) | 0x01;
- txbd->status = BD_SC_READY;
- memset(&txbd->addr[1], 0, txbd->length);
- }
-
- /* set up rxbd for reception */
- rxbd->status = BD_SC_EMPTY;
- rxbd->length = size_to_expect;
- rxbd->addr = datain;
-
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND) {
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
- rxbd->status |= BD_SC_WRAP;
- }
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length,
- txbd->status,
- txbd->addr[0],
- txbd->addr[1]);
- debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- rxbd->length,
- rxbd->status,
- rxbd->addr[0],
- rxbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
- state->rx_idx++;
- state->rxbd = (void *) (rxbd + 1);
-
- return 0;
-}
-
-
-static int i2c_doio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
- volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
- volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
- volatile I2C_BD *txbd, *rxbd;
- volatile int j = 0;
-
- debug("[I2C] i2c_doio\n");
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
-
- if (state->tx_idx <= 0 && state->rx_idx <= 0) {
- debug("[I2C] No I/O is queued\n");
- return I2CERR_QUEUE_EMPTY;
- }
-
- iip->iic_rbptr = iip->iic_rbase;
- iip->iic_tbptr = iip->iic_tbase;
-
- /* Enable I2C */
- debug("[I2C] Enabling I2C...\n");
- i2c->i2c_i2mod |= 0x01;
-
- /* Begin transmission */
- i2c->i2c_i2com |= 0x80;
-
- /* Loop until transmit & receive completed */
-
- if (state->tx_idx > 0) {
- txbd = ((I2C_BD*)state->txbd) - 1;
-
- debug("[I2C] Transmitting...(txbd=0x%08lx)\n",
- (ulong)txbd);
-
- while ((txbd->status & BD_SC_READY) && (j++ < TOUT_LOOP)) {
- if (ctrlc())
- return (-1);
-
- __asm__ __volatile__("eieio");
- }
- }
-
- if ((state->rx_idx > 0) && (j < TOUT_LOOP)) {
- rxbd = ((I2C_BD*)state->rxbd) - 1;
-
- debug("[I2C] Receiving...(rxbd=0x%08lx)\n",
- (ulong)rxbd);
-
- while ((rxbd->status & BD_SC_EMPTY) && (j++ < TOUT_LOOP)) {
- if (ctrlc())
- return (-1);
-
- __asm__ __volatile__("eieio");
- }
- }
-
- /* Turn off I2C */
- i2c->i2c_i2mod &= ~0x01;
-
- if (state->err_cb != NULL) {
- int n, i, b;
-
- /*
- * if we have an error callback function, look at the
- * error bits in the bd status and pass them back
- */
-
- if ((n = state->tx_idx) > 0) {
- for (i = 0; i < n; i++) {
- txbd = ((I2C_BD *) state->txbd) - (n - i);
- if ((b = txbd->status & BD_I2C_TX_ERR) != 0)
- (*state->err_cb) (I2CECB_TX_ERR | b,
- i);
- }
- }
-
- if ((n = state->rx_idx) > 0) {
- for (i = 0; i < n; i++) {
- rxbd = ((I2C_BD *) state->rxbd) - (n - i);
- if ((b = rxbd->status & BD_I2C_RX_ERR) != 0)
- (*state->err_cb) (I2CECB_RX_ERR | b,
- i);
- }
- }
-
- if (j >= TOUT_LOOP)
- (*state->err_cb) (I2CECB_TIMEOUT, 0);
- }
-
- return (j >= TOUT_LOOP) ? I2CERR_TIMEOUT : 0;
-}
-
-static int had_tx_nak;
-
-static void i2c_test_callback(int flags, int xnum)
-{
- if ((flags & I2CECB_TX_ERR) && (flags & I2CECB_TX_NAK))
- had_tx_nak = 1;
-}
-
-int i2c_probe(uchar chip)
-{
- i2c_state_t state;
- int rc;
- uchar buf[1];
-
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
- i2c_newio(&state);
-
- state.err_cb = i2c_test_callback;
- had_tx_nak = 0;
-
- rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1,
- buf);
-
- if (rc != 0)
- return (rc);
-
- rc = i2c_doio(&state);
-
- if ((rc != 0) && (rc != I2CERR_TIMEOUT))
- return (rc);
-
- return (had_tx_nak);
-}
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones like
- * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
- * extra bits end up in the "chip address" bit slots. This makes
- * a 24WC08 (1Kbyte) chip look like four 256 byte chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_read: i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_read: i2c_receive failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_read: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones like
- * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
- * extra bits end up in the "chip address" bit slots. This makes
- * a 24WC08 (1Kbyte) chip look like four 256 byte chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_write: first i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_write: second i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_write: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-#endif /* CONFIG_HARD_I2C */
diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README
index 92a83849ac..89e033e1c5 100644
--- a/board/freescale/m52277evb/README
+++ b/board/freescale/m52277evb/README
@@ -83,7 +83,6 @@ CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README
index 224e79c46a..2fca12c417 100644
--- a/board/freescale/m53017evb/README
+++ b/board/freescale/m53017evb/README
@@ -91,7 +91,6 @@ CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README
index 582e0c3d9e..757f0abdd7 100644
--- a/board/freescale/m5373evb/README
+++ b/board/freescale/m5373evb/README
@@ -90,7 +90,6 @@ CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README
index c563ad99a7..4a8719333a 100644
--- a/board/freescale/m54455evb/README
+++ b/board/freescale/m54455evb/README
@@ -113,7 +113,6 @@ CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README
index 30c5dedafe..ce7b27b8b2 100644
--- a/board/freescale/m547xevb/README
+++ b/board/freescale/m547xevb/README
@@ -98,7 +98,6 @@ CONFIG_DOS_PARTITION -- enable DOS read/write
CONFIG_SLTTMR -- define to use SLT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
2017-05-13 3:09 ` [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD Simon Glass
2017-05-13 3:09 ` [U-Boot] [PATCH v3 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:23 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 04/12] i2c: pdm360ng: " Simon Glass
` (8 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
board/cm5200/cm5200.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
index 2f55191caf..0c647bbd3d 100644
--- a/board/cm5200/cm5200.c
+++ b/board/cm5200/cm5200.c
@@ -214,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf)
strcat(buf, tmp);
}
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
+#if defined(CONFIG_SYS_I2C_SOFT)
/*
* Compose string with hostname.
* buf is assumed to have enough space, and be null-terminated.
@@ -295,7 +295,7 @@ int board_early_init_r(void)
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
+#if defined(CONFIG_SYS_I2C_SOFT)
uchar buf[6];
char str[18];
char hostname[MODULE_NAME_MAXLEN];
@@ -323,7 +323,7 @@ int misc_init_r(void)
compose_hostname(hw_id, hostname);
setenv("hostname", hostname);
-#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
+#endif /* defined(CONFIG_SYS_I2C_SOFT) */
if (!getenv("ethaddr"))
printf(LOG_PREFIX "MAC address not set, networking is not "
"operational\n");
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 04/12] i2c: pdm360ng: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (2 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:23 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 05/12] i2c: keymile: " Simon Glass
` (7 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
board/pdm360ng/pdm360ng.c | 30 ------------------------------
1 file changed, 30 deletions(-)
diff --git a/board/pdm360ng/pdm360ng.c b/board/pdm360ng/pdm360ng.c
index 9db31d3312..371bcd9e6b 100644
--- a/board/pdm360ng/pdm360ng.c
+++ b/board/pdm360ng/pdm360ng.c
@@ -169,36 +169,6 @@ int misc_init_r(void)
clrsetbits_be32(&im->gpio.gpdat, 0x01000000, 0x00040000);
#endif
-#if defined(CONFIG_HARD_I2C)
- if (!getenv("ethaddr")) {
- uchar buf[6];
- uchar ifm_oui[3] = { 0, 2, 1, };
- int ret;
-
- /* I2C-0 for on-board eeprom */
- i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS_NUM);
-
- /* Read ethaddr from EEPROM */
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR,
- CONFIG_SYS_I2C_EEPROM_MAC_OFFSET, 1, buf, 6);
- if (ret != 0) {
- printf("Error: Unable to read MAC from I2C"
- " EEPROM at address %02X:%02X\n",
- CONFIG_SYS_I2C_EEPROM_ADDR,
- CONFIG_SYS_I2C_EEPROM_MAC_OFFSET);
- return 1;
- }
-
- /* Owned by IFM ? */
- if (memcmp(buf, ifm_oui, sizeof(ifm_oui))) {
- printf("Illegal MAC address in EEPROM: %pM\n", buf);
- return 1;
- }
-
- eth_setenv_enetaddr("ethaddr", buf);
- }
-#endif /* defined(CONFIG_HARD_I2C) */
-
return 0;
}
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 05/12] i2c: keymile: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (3 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 04/12] i2c: pdm360ng: " Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:24 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 06/12] i2c: mxc_i2c: " Simon Glass
` (6 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
board/keymile/km82xx/km82xx.c | 5 -----
board/keymile/km_arm/km_arm.c | 4 ----
2 files changed, 9 deletions(-)
diff --git a/board/keymile/km82xx/km82xx.c b/board/keymile/km82xx/km82xx.c
index 51b4571d40..f5a98b33e7 100644
--- a/board/keymile/km82xx/km82xx.c
+++ b/board/keymile/km82xx/km82xx.c
@@ -153,13 +153,8 @@ const iop_conf_t iop_conf_tab[4][32] = {
{ 0, 0, 0, 0, 0, 0 }, /* PD18 */
{ 0, 0, 0, 0, 0, 0 }, /* PD17 */
{ 0, 0, 0, 0, 0, 0 }, /* PD16 */
-#if defined(CONFIG_HARD_I2C)
- { 1, 1, 1, 0, 1, 0 }, /* PD15 I2C SDA */
- { 1, 1, 1, 0, 1, 0 }, /* PD14 I2C SCL */
-#else
{ 1, 0, 0, 0, 1, 1 }, /* PD15 */
{ 1, 0, 0, 1, 1, 1 }, /* PD14 */
-#endif
{ 0, 0, 0, 0, 0, 0 }, /* PD13 */
{ 0, 0, 0, 0, 0, 0 }, /* PD12 */
{ 0, 0, 0, 0, 0, 0 }, /* PD11 */
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 079509c979..85785ffc02 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -75,10 +75,6 @@ static const u32 kwmpp_config[] = {
#if defined(CONFIG_SYS_I2C_SOFT)
MPP8_GPIO, /* SDA */
MPP9_GPIO, /* SCL */
-#endif
-#if defined(CONFIG_HARD_I2C)
- MPP8_TW_SDA,
- MPP9_TW_SCK,
#endif
MPP10_UART0_TXD,
MPP11_UART0_RXD,
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 06/12] i2c: mxc_i2c: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (4 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 05/12] i2c: keymile: " Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:24 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD Simon Glass
` (5 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
drivers/i2c/mxc_i2c.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
index 13ec0e63b1..b68e82770b 100644
--- a/drivers/i2c/mxc_i2c.c
+++ b/drivers/i2c/mxc_i2c.c
@@ -69,10 +69,6 @@ DECLARE_GLOBAL_DATA_PTR;
#define I2SR_IIF_CLEAR (0 << 1)
#endif
-#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE)
-#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver"
-#endif
-
#ifdef I2C_QUIRK_REG
static u16 i2c_clk_div[60][2] = {
{ 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 },
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (5 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 06/12] i2c: mxc_i2c: " Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-13 15:22 ` Tom Rini
2017-05-15 4:24 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD Simon Glass
` (4 subsequent siblings)
11 siblings, 2 replies; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
---
Changes in v3: None
Changes in v2:
- Add new patch to adjust omap boards to not need CONFIG_I2C_HARD
board/ti/am335x/board.c | 3 ++-
board/ti/am43xx/board.c | 3 ++-
2 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 3e81521399..517965c0f0 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -72,7 +72,8 @@ void do_board_detect(void)
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
- if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR))
+ if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
+ CONFIG_EEPROM_CHIP_ADDRESS))
printf("ti_i2c_eeprom_init failed\n");
}
#endif
diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
index f633e2f85d..f44103d4d6 100644
--- a/board/ti/am43xx/board.c
+++ b/board/ti/am43xx/board.c
@@ -42,7 +42,8 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
#ifdef CONFIG_TI_I2C_BOARD_DETECT
void do_board_detect(void)
{
- if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR))
+ if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
+ CONFIG_EEPROM_CHIP_ADDRESS))
printf("ti_i2c_eeprom_init failed\n");
}
#endif
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (6 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-13 15:22 ` Tom Rini
2017-05-15 4:25 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX Simon Glass
` (3 subsequent siblings)
11 siblings, 2 replies; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3:
- Update commit message so that it is unique in the series
- Fix up #ifdef in cmd/eeprom.c
- Drop changes to include/config headers
Changes in v2:
- Drop changes to omap board.c files
README | 16 ++++++++--------
cmd/eeprom.c | 2 --
common/board_f.c | 4 ++--
common/stdio.c | 5 +----
scripts/config_whitelist.txt | 1 -
5 files changed, 11 insertions(+), 17 deletions(-)
diff --git a/README b/README
index 86f0814f79..11fa84ccc4 100644
--- a/README
+++ b/README
@@ -2204,7 +2204,9 @@ The following options need to be configured:
If you do not have i2c muxes on your board, omit this define.
-- Legacy I2C Support: CONFIG_HARD_I2C
+----under removal:
+
+- Legacy I2C Support: CONFIG_SOFT_I2C
NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
provides the following compelling advantages:
@@ -2213,14 +2215,12 @@ The following options need to be configured:
- approved multibus support
- better i2c mux support
- ** CONFIG_HARD_I2C is now being removed **
-
-----under removal:
+ ** CONFIG_SOFT_I2C is now being removed **
- In both cases you will need to define CONFIG_SYS_I2C_SPEED
- to be the frequency (in Hz) at which you wish your i2c bus
- to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
- the CPU's i2c node address).
+ With CONFIG_SOFT_I2C you will need to define
+ CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you
+ wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the
+ address of this node (ie the CPU's i2c node address).
Now, the u-boot i2c code for the mpc8xx
(arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
diff --git a/cmd/eeprom.c b/cmd/eeprom.c
index 0a0e4a2c1c..e43566bc56 100644
--- a/cmd/eeprom.c
+++ b/cmd/eeprom.c
@@ -73,11 +73,9 @@ void eeprom_init(int bus)
#endif
/* I2C EEPROM */
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
#if defined(CONFIG_SYS_I2C)
if (bus >= 0)
i2c_set_bus_num(bus);
-#endif
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
}
diff --git a/common/board_f.c b/common/board_f.c
index d9431ee79a..eed3e7be2a 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -184,7 +184,7 @@ __weak int dram_init_banksize(void)
return 0;
}
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_SYS_I2C)
static int init_func_i2c(void)
{
puts("I2C: ");
@@ -765,7 +765,7 @@ static const init_fnc_t init_sequence_f[] = {
misc_init_f,
#endif
INIT_FUNC_WATCHDOG_RESET
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_SYS_I2C)
init_func_i2c,
#endif
#if defined(CONFIG_HARD_SPI)
diff --git a/common/stdio.c b/common/stdio.c
index 4d30017530..ee4f0bda9e 100644
--- a/common/stdio.c
+++ b/common/stdio.c
@@ -21,7 +21,7 @@
#include <logbuff.h>
#endif
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_SYS_I2C)
#include <i2c.h>
#endif
@@ -346,9 +346,6 @@ int stdio_add_devices(void)
#ifdef CONFIG_SYS_I2C
i2c_init_all();
#else
-#if defined(CONFIG_HARD_I2C)
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
#endif
#ifdef CONFIG_DM_VIDEO
/*
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index 7646bb6842..da37e49c83 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -1134,7 +1134,6 @@ CONFIG_G_DNL_UMS_VENDOR_NUM
CONFIG_H264_FREQ
CONFIG_H8300
CONFIG_HALEAKALA
-CONFIG_HARD_I2C
CONFIG_HARD_SPI
CONFIG_HASH_VERIFY
CONFIG_HAS_DATAFLASH
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (7 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:25 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT Simon Glass
` (2 subsequent siblings)
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
README | 2 --
1 file changed, 2 deletions(-)
diff --git a/README b/README
index 11fa84ccc4..9f9265dc6d 100644
--- a/README
+++ b/README
@@ -2228,8 +2228,6 @@ The following options need to be configured:
eg, MPC823e User's Manual p.16-473). So, set
CONFIG_SYS_I2C_SLAVE to 0.
- CONFIG_SYS_I2C_INIT_MPC5XXX
-
When a board is reset during an i2c bus transfer
chips might think that the current transfer is still
in progress. Reset the slave devices by sending start
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (8 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:25 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 11/12] Drop CONFIG_I2CFAST Simon Glass
2017-05-13 3:10 ` [U-Boot] [PATCH v3 12/12] Drop use of CONFIG_I2C_SOFT Simon Glass
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
This option is not used by any boards. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
README | 11 -----------
drivers/i2c/fsl_i2c.c | 9 ---------
drivers/i2c/fti2c010.c | 9 ---------
include/i2c.h | 3 ---
scripts/config_whitelist.txt | 1 -
5 files changed, 33 deletions(-)
diff --git a/README b/README
index 9f9265dc6d..96ce6289ea 100644
--- a/README
+++ b/README
@@ -2323,17 +2323,6 @@ The following options need to be configured:
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
- CONFIG_SYS_I2C_BOARD_LATE_INIT
-
- An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
- defined a custom i2c_board_late_init() routine in
- boards/xxx/board.c is run AFTER the operations in i2c_init()
- is completed. This callpoint can be used to unreset i2c bus
- using CPU i2c controller register accesses for CPUs whose i2c
- controller provide such a method. It is called at the end of
- i2c_init() to allow i2c_init operations to setup the i2c bus
- controller on the CPU (e.g. setting bus speed & slave address).
-
CONFIG_I2CFAST (PPC405GP|PPC405EP only)
This option enables configuration of bi_iic_fast[] flags
diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
index a1406baa87..ff3dc25927 100644
--- a/drivers/i2c/fsl_i2c.c
+++ b/drivers/i2c/fsl_i2c.c
@@ -284,15 +284,6 @@ static void __i2c_init(const struct fsl_i2c_base *base, int speed, int
break;
}
-
-#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
- /* Call board specific i2c bus reset routine AFTER the bus has been
- * initialized. Use either this callpoint or i2c_init_board;
- * which is called before i2c_init operations.
- * For details about this problem see doc/I2C_Edge_Conditions.
- */
- i2c_board_late_init();
-#endif
}
static int
diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c
index b35d0d2d9c..4da959fa53 100644
--- a/drivers/i2c/fti2c010.c
+++ b/drivers/i2c/fti2c010.c
@@ -146,15 +146,6 @@ static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr)
set_i2c_bus_speed(chip, speed);
/* slave init, don't care */
-
-#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
- /* Call board specific i2c bus reset routine AFTER the bus has been
- * initialized. Use either this callpoint or i2c_init_board;
- * which is called before fti2c010_init operations.
- * For details about this problem see doc/I2C_Edge_Conditions.
- */
- i2c_board_late_init();
-#endif
}
/*
diff --git a/include/i2c.h b/include/i2c.h
index cd7f61e1c1..a88cc7cddf 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -706,9 +706,6 @@ void i2c_early_init_f(void);
#endif
void i2c_init(int speed, int slaveaddr);
void i2c_init_board(void);
-#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
-void i2c_board_late_init(void);
-#endif
#ifdef CONFIG_SYS_I2C
/*
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index da37e49c83..5cdca33f87 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -4222,7 +4222,6 @@ CONFIG_SYS_I2C_BASE2
CONFIG_SYS_I2C_BASE3
CONFIG_SYS_I2C_BASE4
CONFIG_SYS_I2C_BASE5
-CONFIG_SYS_I2C_BOARD_LATE_INIT
CONFIG_SYS_I2C_BOOT_EEPROM_ADDR
CONFIG_SYS_I2C_BUSES
CONFIG_SYS_I2C_BUS_MAX
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 11/12] Drop CONFIG_I2CFAST
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (9 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT Simon Glass
@ 2017-05-13 3:09 ` Simon Glass
2017-05-15 4:26 ` Heiko Schocher
2017-05-13 3:10 ` [U-Boot] [PATCH v3 12/12] Drop use of CONFIG_I2C_SOFT Simon Glass
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:09 UTC (permalink / raw)
To: u-boot
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3: None
Changes in v2: None
README | 6 ------
common/board_r.c | 17 -----------------
scripts/config_whitelist.txt | 1 -
3 files changed, 24 deletions(-)
diff --git a/README b/README
index 96ce6289ea..71d8de0ba8 100644
--- a/README
+++ b/README
@@ -2323,12 +2323,6 @@ The following options need to be configured:
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
- CONFIG_I2CFAST (PPC405GP|PPC405EP only)
-
- This option enables configuration of bi_iic_fast[] flags
- in u-boot bd_info structure based on u-boot environment
- variable "i2cfast". (see also i2cfast)
-
CONFIG_I2C_MULTI_BUS
This option allows the use of multiple I2C buses, each of which
diff --git a/common/board_r.c b/common/board_r.c
index d69a33c4a3..dba2102b18 100644
--- a/common/board_r.c
+++ b/common/board_r.c
@@ -485,24 +485,7 @@ static int initr_env(void)
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
-#if defined(CONFIG_SYS_EXTBDINFO)
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
-#if defined(CONFIG_I2CFAST)
- /*
- * set bi_iic_fast for linux taking environment variable
- * "i2cfast" into account
- */
- {
- char *s = getenv("i2cfast");
- if (s && ((*s == 'y') || (*s == 'Y'))) {
- gd->bd->bi_iic_fast[0] = 1;
- gd->bd->bi_iic_fast[1] = 1;
- }
- }
-#endif /* CONFIG_I2CFAST */
-#endif /* CONFIG_405GP, CONFIG_405EP */
-#endif /* CONFIG_SYS_EXTBDINFO */
return 0;
}
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index 5cdca33f87..7cdfcd0a52 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -1319,7 +1319,6 @@ CONFIG_HW_ENV_SETTINGS
CONFIG_HW_WATCHDOG
CONFIG_HW_WATCHDOG_TIMEOUT_MS
CONFIG_I2C
-CONFIG_I2CFAST
CONFIG_I2C_CHIPADDRESS
CONFIG_I2C_CMD_TREE
CONFIG_I2C_ENV_EEPROM_BUS
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 12/12] Drop use of CONFIG_I2C_SOFT
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
` (10 preceding siblings ...)
2017-05-13 3:09 ` [U-Boot] [PATCH v3 11/12] Drop CONFIG_I2CFAST Simon Glass
@ 2017-05-13 3:10 ` Simon Glass
2017-05-15 4:26 ` Heiko Schocher
11 siblings, 1 reply; 27+ messages in thread
From: Simon Glass @ 2017-05-13 3:10 UTC (permalink / raw)
To: u-boot
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
Changes in v3:
- Rebase to master
Changes in v2:
- Rebase to master
README | 32 +-------------------------------
1 file changed, 1 insertion(+), 31 deletions(-)
diff --git a/README b/README
index 71d8de0ba8..9525199551 100644
--- a/README
+++ b/README
@@ -2204,37 +2204,7 @@ The following options need to be configured:
If you do not have i2c muxes on your board, omit this define.
-----under removal:
-
-- Legacy I2C Support: CONFIG_SOFT_I2C
-
- NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
- provides the following compelling advantages:
-
- - more than one i2c adapter is usable
- - approved multibus support
- - better i2c mux support
-
- ** CONFIG_SOFT_I2C is now being removed **
-
- With CONFIG_SOFT_I2C you will need to define
- CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you
- wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the
- address of this node (ie the CPU's i2c node address).
-
- Now, the u-boot i2c code for the mpc8xx
- (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
- and so its address should therefore be cleared to 0 (See,
- eg, MPC823e User's Manual p.16-473). So, set
- CONFIG_SYS_I2C_SLAVE to 0.
-
- When a board is reset during an i2c bus transfer
- chips might think that the current transfer is still
- in progress. Reset the slave devices by sending start
- commands until the slave device responds.
-
- That's all that's required for CONFIG_HARD_I2C.
-
+- Legacy I2C Support:
If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
then the following macros need to be defined (examples are
from include/configs/lwmon.h):
--
2.13.0.rc2.291.g57267f2277-goog
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD Simon Glass
@ 2017-05-13 15:22 ` Tom Rini
2017-05-15 4:24 ` Heiko Schocher
1 sibling, 0 replies; 27+ messages in thread
From: Tom Rini @ 2017-05-13 15:22 UTC (permalink / raw)
To: u-boot
On Fri, May 12, 2017 at 09:09:55PM -0600, Simon Glass wrote:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170513/8629ffb8/attachment.sig>
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD Simon Glass
@ 2017-05-13 15:22 ` Tom Rini
2017-05-15 4:25 ` Heiko Schocher
1 sibling, 0 replies; 27+ messages in thread
From: Tom Rini @ 2017-05-13 15:22 UTC (permalink / raw)
To: u-boot
On Fri, May 12, 2017 at 09:09:56PM -0600, Simon Glass wrote:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170513/294c5dc1/attachment.sig>
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD Simon Glass
@ 2017-05-15 4:22 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:22 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> This option is pretty old. It predates CONFIG_SYS_I2C which is itself
> deprecated in favour of driver model. Disable it for all boards.
>
> Also drop I2C options which depend on this.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
Thanks!
Applied to u-boot-i2c.git master
u-boot-2ic master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> Changes in v3: None
> Changes in v2: None
>
> README | 17 +--
> arch/arm/include/asm/arch-armada100/config.h | 12 --
> board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c | 12 +-
> board/cm5200/cm5200.c | 32 ++---
> board/cm5200/cmd_cm5200.c | 32 +----
> board/davedenx/aria/aria.c | 3 -
> board/esd/mecp5123/mecp5123.c | 12 +-
> board/freescale/mpc5121ads/mpc5121ads.c | 21 ----
> board/ifm/ac14xx/ac14xx.c | 53 +-------
> board/renesas/r0p7734/r0p7734.c | 12 +-
> board/tqc/tqm5200/tqm5200.c | 18 +--
> configs/MiniFAP_defconfig | 2 -
> configs/O2D300_defconfig | 1 -
> configs/O2DNT2_RAMBOOT_defconfig | 1 -
> configs/O2DNT2_defconfig | 1 -
> configs/O2D_defconfig | 1 -
> configs/O2I_defconfig | 1 -
> configs/O2MNT_O2M110_defconfig | 1 -
> configs/O2MNT_O2M112_defconfig | 1 -
> configs/O2MNT_O2M113_defconfig | 1 -
> configs/O2MNT_defconfig | 1 -
> configs/O3DNT_defconfig | 1 -
> configs/TQM5200S_HIGHBOOT_defconfig | 2 -
> configs/TQM5200S_defconfig | 2 -
> configs/TQM5200_B_HIGHBOOT_defconfig | 2 -
> configs/TQM5200_B_defconfig | 2 -
> configs/TQM5200_STK100_defconfig | 2 -
> configs/TQM5200_defconfig | 2 -
> configs/a4m072_defconfig | 1 -
> configs/ac14xx_defconfig | 1 -
> configs/ap_sh4a_4a_defconfig | 1 -
> configs/apx4devkit_defconfig | 2 -
> configs/aria_defconfig | 1 -
> configs/aspenite_defconfig | 1 -
> configs/cam5200_defconfig | 2 -
> configs/cam5200_niosflash_defconfig | 2 -
> configs/charon_defconfig | 1 -
> configs/cm5200_defconfig | 1 -
> configs/digsy_mtc_RAMBOOT_defconfig | 2 -
> configs/digsy_mtc_defconfig | 2 -
> configs/digsy_mtc_rev5_RAMBOOT_defconfig | 2 -
> configs/digsy_mtc_rev5_defconfig | 2 -
> configs/fo300_defconfig | 2 -
> configs/gplugd_defconfig | 1 -
> configs/ipek01_defconfig | 2 -
> configs/m28evk_defconfig | 1 -
> configs/mecp5123_defconfig | 2 -
> configs/motionpro_defconfig | 2 -
> configs/mpc5121ads_defconfig | 2 -
> configs/mpc5121ads_rev2_defconfig | 2 -
> configs/pcm030_LOWBOOT_defconfig | 2 -
> configs/pcm030_defconfig | 2 -
> configs/pdm360ng_defconfig | 2 -
> configs/r0p7734_defconfig | 1 -
> configs/v38b_defconfig | 2 -
> include/common.h | 10 ++
> include/configs/M54418TWR.h | 1 -
> include/configs/TQM5200.h | 64 +---------
> include/configs/a4m072.h | 20 ---
> include/configs/ac14xx.h | 18 ---
> include/configs/ap_sh4a_4a.h | 14 ---
> include/configs/apx4devkit.h | 6 -
> include/configs/aria.h | 21 ----
> include/configs/axs10x.h | 2 +-
> include/configs/cm5200.h | 12 +-
> include/configs/digsy_mtc.h | 31 -----
> include/configs/ids8313.h | 1 -
> include/configs/ipek01.h | 23 ----
> include/configs/jupiter.h | 19 ---
> include/configs/m28evk.h | 6 -
> include/configs/manroland/mpc5200-common.h | 176 +++++++++++++++++++++++++++
> include/configs/mecp5123.h | 18 +--
> include/configs/motionpro.h | 22 ----
> include/configs/mpc5121ads.h | 18 ---
> include/configs/mxs.h | 10 --
> include/configs/o2dnt-common.h | 22 ----
> include/configs/pcm030.h | 31 +----
> include/configs/pdm360ng.h | 30 -----
> include/configs/r0p7734.h | 14 ---
> include/configs/s32v234evb.h | 10 --
> include/configs/v38b.h | 21 ----
> 81 files changed, 211 insertions(+), 701 deletions(-)
> create mode 100644 include/configs/manroland/mpc5200-common.h
>
> diff --git a/README b/README
> index 2ca0102b57..86f0814f79 100644
> --- a/README
> +++ b/README
> @@ -2213,22 +2213,9 @@ The following options need to be configured:
> - approved multibus support
> - better i2c mux support
>
> - ** Please consider updating your I2C driver now. **
> + ** CONFIG_HARD_I2C is now being removed **
>
> - These enable legacy I2C serial bus commands. Defining
> - CONFIG_HARD_I2C will include the appropriate I2C driver
> - for the selected CPU.
> -
> - This will allow you to use i2c commands at the u-boot
> - command line (as long as you set CONFIG_CMD_I2C in
> - CONFIG_COMMANDS) and communicate with i2c based realtime
> - clock chips. See common/cmd_i2c.c for a description of the
> - command line interface.
> -
> - CONFIG_HARD_I2C selects a hardware I2C controller.
> -
> - There are several other quantities that must also be
> - defined when you define CONFIG_HARD_I2C.
> +----under removal:
>
> In both cases you will need to define CONFIG_SYS_I2C_SPEED
> to be the frequency (in Hz) at which you wish your i2c bus
> diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
> index 6ebc759f4b..113e1c73f3 100644
> --- a/arch/arm/include/asm/arch-armada100/config.h
> +++ b/arch/arm/include/asm/arch-armada100/config.h
> @@ -24,17 +24,5 @@
> #define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE
> #define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register
> represents UART Unit Enable */
> -/*
> - * I2C definition
> - */
> -#ifdef CONFIG_CMD_I2C
> -#define CONFIG_I2C_MV 1
> -#define CONFIG_MV_I2C_NUM 2
> -#define CONFIG_I2C_MULTI_BUS 1
> -#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000}
> -#define CONFIG_HARD_I2C 1
> -#define CONFIG_SYS_I2C_SPEED 0
> -#define CONFIG_SYS_I2C_SLAVE 0xfe
> -#endif
>
> #endif /* _ARMD1_CONFIG_H */
> diff --git a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
> index 31418a1f96..9205c22e0b 100644
> --- a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
> +++ b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
> @@ -156,17 +156,7 @@ int board_init(void)
>
> int board_late_init(void)
> {
> - u8 mac[6];
> -
> - /* Read Mac Address and set*/
> - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
> -
> - /* Read MAC address */
> - i2c_read(0x50, 0x0, 0, mac, 6);
> -
> - if (is_valid_ethaddr(mac))
> - eth_setenv_enetaddr("ethaddr", mac);
> + printf("Cannot use I2C to get MAC address\n");
>
> return 0;
> }
> diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
> index 7b862355c8..2f55191caf 100644
> --- a/board/cm5200/cm5200.c
> +++ b/board/cm5200/cm5200.c
> @@ -161,14 +161,7 @@ int dram_init(void)
> */
> static void read_hw_id(hw_id_t hw_id)
> {
> - int i;
> - for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
> - if (i2c_read(CONFIG_SYS_I2C_EEPROM,
> - hw_id_format[i].offset,
> - 2,
> - (uchar *)&hw_id[i][0],
> - hw_id_format[i].length) != 0)
> - printf("ERROR: can't read HW ID from EEPROM\n");
> + printf("ERROR: can't read HW ID from EEPROM\n");
> }
>
>
> @@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf)
> strcat(buf, tmp);
> }
>
> -
> +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
> /*
> * Compose string with hostname.
> * buf is assumed to have enough space, and be null-terminated.
> @@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf)
> *p = tolower(*p);
>
> }
> -
> +#endif
>
> #ifdef CONFIG_OF_BOARD_SETUP
> /*
> @@ -270,15 +263,6 @@ int checkboard(void)
> hw_id_t hw_id_tmp;
> char module_name_tmp[MODULE_NAME_MAXLEN] = "";
>
> - /*
> - * We need I2C to access HW ID data from EEPROM, so we call i2c_init()
> - * here despite the fact that it will be called again later on. We
> - * also use a little trick to silence I2C-related output.
> - */
> - gd->flags |= GD_FLG_SILENT;
> - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> - gd->flags &= ~GD_FLG_SILENT;
> -
> read_hw_id(hw_id_tmp);
> identify_module(hw_id_tmp); /* this sets gd->board_type */
> compose_module_name(hw_id_tmp, module_name_tmp);
> @@ -334,16 +318,16 @@ int misc_init_r(void)
> " device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
> CONFIG_MAC_OFFSET);
> }
> + hostname[0] = 0x00;
> + /* set the hostname appropriate to the module we're running on */
> + compose_hostname(hw_id, hostname);
> + setenv("hostname", hostname);
> +
> #endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
> if (!getenv("ethaddr"))
> printf(LOG_PREFIX "MAC address not set, networking is not "
> "operational\n");
>
> - /* set the hostname appropriate to the module we're running on */
> - hostname[0] = 0x00;
> - compose_hostname(hw_id, hostname);
> - setenv("hostname", hostname);
> -
> return 0;
> }
> #endif /* CONFIG_MISC_INIT_R */
> diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c
> index 9c40ad7b2a..60097dc8c7 100644
> --- a/board/cm5200/cmd_cm5200.c
> +++ b/board/cm5200/cmd_cm5200.c
> @@ -13,34 +13,6 @@
>
> #ifdef CONFIG_CMD_BSP
>
> -static int do_i2c_test(char * const argv[])
> -{
> - unsigned char temp, temp1;
> -
> - printf("Starting I2C Test\n"
> - "Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
> - "Please press any key to start\n\n");
> - getc();
> -
> - temp = 0xf0; /* set io 0-4 as output */
> - i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1);
> -
> - printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
> - "Press any key to stop\n\n");
> -
> - while (!tstc()) {
> - i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1);
> - temp1 = (temp >> 4) & 0x03;
> - temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
> - temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
> - temp = temp1;
> - i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1);
> - }
> - getc();
> -
> - return 0;
> -}
> -
> static int do_usb_test(char * const argv[])
> {
> int i;
> @@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
>
> switch (argc) {
> case 2:
> - if (strncmp(argv[1], "i2c", 3) == 0)
> - rcode = do_i2c_test(argv);
> - else if (strncmp(argv[1], "led", 3) == 0)
> + if (strncmp(argv[1], "led", 3) == 0)
> rcode = do_led_test(argv);
> else if (strncmp(argv[1], "usb", 3) == 0)
> rcode = do_usb_test(argv);
> diff --git a/board/davedenx/aria/aria.c b/board/davedenx/aria/aria.c
> index e3441cad4e..e389819e9d 100644
> --- a/board/davedenx/aria/aria.c
> +++ b/board/davedenx/aria/aria.c
> @@ -29,9 +29,6 @@ int misc_init_r(void)
> {
> u32 tmp;
>
> - /* we use I2C-2 for on-board eeprom */
> - i2c_set_bus_num(2);
> -
> tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE);
> printf("FPGA: %u-%u.%u.%u\n",
> (tmp & 0xFF000000) >> 24,
> diff --git a/board/esd/mecp5123/mecp5123.c b/board/esd/mecp5123/mecp5123.c
> index 66dc407bae..78a6b66110 100644
> --- a/board/esd/mecp5123/mecp5123.c
> +++ b/board/esd/mecp5123/mecp5123.c
> @@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR;
>
> int eeprom_write_enable(unsigned dev_addr, int state)
> {
> - volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
> -
> - if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR)
> - return -1;
> -
> - if (state == 0)
> - setbits_be32(&im->gpio.gpdat, 0x00100000);
> - else
> - clrbits_be32(&im->gpio.gpdat, 0x00100000);
> -
> - return 0;
> + return -ENOSYS;
> }
>
> int board_early_init_f(void)
> diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c
> index f87579f193..d729056fd0 100644
> --- a/board/freescale/mpc5121ads/mpc5121ads.c
> +++ b/board/freescale/mpc5121ads/mpc5121ads.c
> @@ -174,27 +174,6 @@ int dram_init(void)
>
> int misc_init_r(void)
> {
> - u8 tmp_val;
> -
> - /* Using this for DIU init before the driver in linux takes over
> - * Enable the TFP410 Encoder (I2C address 0x38)
> - */
> -
> - i2c_set_bus_num(2);
> - tmp_val = 0xBF;
> - i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
> - /* Verify if enabled */
> - tmp_val = 0;
> - i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
> - debug("DVI Encoder Read: 0x%02x\n", tmp_val);
> -
> - tmp_val = 0x10;
> - i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
> - /* Verify if enabled */
> - tmp_val = 0;
> - i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
> - debug("DVI Encoder Read: 0x%02x\n", tmp_val);
> -
> return 0;
> }
>
> diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c
> index 348613736d..cd79e804a0 100644
> --- a/board/ifm/ac14xx/ac14xx.c
> +++ b/board/ifm/ac14xx/ac14xx.c
> @@ -17,7 +17,6 @@
> #include <i2c.h>
> #endif
>
> -static int eeprom_diag;
> static int mac_diag;
> static int gpio_diag;
>
> @@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout {
> #define HW_COMP_MAINCPU 2
>
> static struct eeprom_layout eeprom_content;
> -static int eeprom_was_read; /* has_been_read */
> static int eeprom_is_valid;
> static int eeprom_version;
>
> @@ -153,53 +151,7 @@ static int eeprom_version;
>
> static int read_eeprom(void)
> {
> - int eeprom_datalen;
> - int ret;
> -
> - if (eeprom_was_read)
> - return 0;
> -
> - eeprom_is_valid = 0;
> - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
> - CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
> - (uchar *)&eeprom_content, sizeof(eeprom_content));
> - if (eeprom_diag) {
> - printf("DIAG: %s() read rc[%d], size[%d]\n",
> - __func__, ret, sizeof(eeprom_content));
> - }
> -
> - if (ret != 0)
> - return -1;
> -
> - eeprom_was_read = 1;
> -
> - /*
> - * check validity of EEPROM content
> - * (check version, length, optionally checksum)
> - */
> - eeprom_is_valid = 1;
> - eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
> - eeprom_version = get_eeprom_field_int(eeprom_content.version);
> -
> - if (eeprom_diag) {
> - printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
> - __func__, eeprom_content.magic[0],
> - eeprom_content.magic[1], eeprom_content.magic[2],
> - eeprom_datalen, eeprom_version, eeprom_content.type);
> - }
> - if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
> - eeprom_is_valid = 0;
> - if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
> - eeprom_is_valid = 0;
> - if ((eeprom_version != 1) && (eeprom_version != 2))
> - eeprom_is_valid = 0;
> - if (eeprom_content.type != HW_COMP_MAINCPU)
> - eeprom_is_valid = 0;
> -
> - if (eeprom_diag)
> - printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);
> -
> - return ret;
> + return -ENOSYS;
> }
>
> int mac_read_from_eeprom(void)
> @@ -324,9 +276,6 @@ int misc_init_r(void)
> char *s;
> int want_recovery;
>
> - /* we use bus I2C-0 for the on-board eeprom */
> - i2c_set_bus_num(0);
> -
> /* setup GPIO directions and initial values */
> gpio_configure();
>
> diff --git a/board/renesas/r0p7734/r0p7734.c b/board/renesas/r0p7734/r0p7734.c
> index 360e0a1a6f..d0b4537513 100644
> --- a/board/renesas/r0p7734/r0p7734.c
> +++ b/board/renesas/r0p7734/r0p7734.c
> @@ -44,17 +44,7 @@ int board_init(void)
>
> int board_late_init(void)
> {
> - u8 mac[6];
> -
> - /* Read Mac Address and set*/
> - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
> -
> - /* Read MAC address */
> - i2c_read(0x50, 0x10, 0, mac, 6);
> -
> - if (is_valid_ethaddr(mac))
> - eth_setenv_enetaddr("ethaddr", mac);
> + printf("Cannot get MAC address from I2C\n");
>
> return 0;
> }
> diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c
> index 92db093dbf..c48ab11fc4 100644
> --- a/board/tqc/tqm5200/tqm5200.c
> +++ b/board/tqc/tqm5200/tqm5200.c
> @@ -486,20 +486,14 @@ int board_early_init_f (void)
>
> static int tfp410_read_reg(int reg, uchar *buf)
> {
> - if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) {
> - puts ("Error reading the chip.\n");
> - return 1;
> - }
> - return 0;
> + puts("Error reading the chip.\n");
> + return -ENOSYS;
> }
>
> static int tfp410_write_reg(int reg, uchar buf)
> {
> - if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) {
> - puts ("Error writing the chip.\n");
> - return 1;
> - }
> - return 0;
> + puts("Error writing the chip.\n");
> + return -ENOSYS;
> }
>
> typedef struct _tfp410_config {
> @@ -525,12 +519,9 @@ static int charon_last_stage_init(void)
> {
> volatile struct mpc5xxx_lpb *lpb =
> (struct mpc5xxx_lpb *) MPC5XXX_LPB;
> - int oldbus = i2c_get_bus_num();
> uchar buf;
> int i = 0;
>
> - i2c_set_bus_num(CONFIG_SYS_TFP410_BUS);
> -
> /* check version */
> if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0)
> return -1;
> @@ -551,7 +542,6 @@ static int charon_last_stage_init(void)
> i++;
> }
> printf("TFP410 initialized.\n");
> - i2c_set_bus_num(oldbus);
>
> /* set deadcycle for cs3 to 0 */
> setbits_be32(&lpb->cs_deadcycle, 0xffffcfff);
> diff --git a/configs/MiniFAP_defconfig b/configs/MiniFAP_defconfig
> index 7d719f81f5..02ca577e28 100644
> --- a/configs/MiniFAP_defconfig
> +++ b/configs/MiniFAP_defconfig
> @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/O2D300_defconfig b/configs/O2D300_defconfig
> index 38101f05df..c0e9541b87 100644
> --- a/configs/O2D300_defconfig
> +++ b/configs/O2D300_defconfig
> @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2DNT2_RAMBOOT_defconfig b/configs/O2DNT2_RAMBOOT_defconfig
> index 83006e5582..8cff44cf36 100644
> --- a/configs/O2DNT2_RAMBOOT_defconfig
> +++ b/configs/O2DNT2_RAMBOOT_defconfig
> @@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y
> CONFIG_AUTOBOOT_KEYED=y
> CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
> CONFIG_AUTOBOOT_STOP_STR="++++++++++"
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2DNT2_defconfig b/configs/O2DNT2_defconfig
> index 4202d85203..f29abb83bc 100644
> --- a/configs/O2DNT2_defconfig
> +++ b/configs/O2DNT2_defconfig
> @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
> CONFIG_AUTOBOOT_KEYED=y
> CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
> CONFIG_AUTOBOOT_STOP_STR="++++++++++"
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2D_defconfig b/configs/O2D_defconfig
> index b84a1c8839..534cfe12e2 100644
> --- a/configs/O2D_defconfig
> +++ b/configs/O2D_defconfig
> @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2I_defconfig b/configs/O2I_defconfig
> index efcc769ff4..acf42abe29 100644
> --- a/configs/O2I_defconfig
> +++ b/configs/O2I_defconfig
> @@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2MNT_O2M110_defconfig b/configs/O2MNT_O2M110_defconfig
> index abdc53df21..de647c76b9 100644
> --- a/configs/O2MNT_O2M110_defconfig
> +++ b/configs/O2MNT_O2M110_defconfig
> @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
> CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\""
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2MNT_O2M112_defconfig b/configs/O2MNT_O2M112_defconfig
> index 06089fe3cf..b243e9cc0e 100644
> --- a/configs/O2MNT_O2M112_defconfig
> +++ b/configs/O2MNT_O2M112_defconfig
> @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
> CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\""
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2MNT_O2M113_defconfig b/configs/O2MNT_O2M113_defconfig
> index 1ea3f3a09b..1584058289 100644
> --- a/configs/O2MNT_O2M113_defconfig
> +++ b/configs/O2MNT_O2M113_defconfig
> @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
> CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\""
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O2MNT_defconfig b/configs/O2MNT_defconfig
> index 0209085605..20bd31466e 100644
> --- a/configs/O2MNT_defconfig
> +++ b/configs/O2MNT_defconfig
> @@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/O3DNT_defconfig b/configs/O3DNT_defconfig
> index 5ce4140859..ea769e7edc 100644
> --- a/configs/O3DNT_defconfig
> +++ b/configs/O3DNT_defconfig
> @@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/TQM5200S_HIGHBOOT_defconfig b/configs/TQM5200S_HIGHBOOT_defconfig
> index d0cd50a63c..d07596add0 100644
> --- a/configs/TQM5200S_HIGHBOOT_defconfig
> +++ b/configs/TQM5200S_HIGHBOOT_defconfig
> @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/TQM5200S_defconfig b/configs/TQM5200S_defconfig
> index 5324a9a11c..af3225554b 100644
> --- a/configs/TQM5200S_defconfig
> +++ b/configs/TQM5200S_defconfig
> @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/TQM5200_B_HIGHBOOT_defconfig b/configs/TQM5200_B_HIGHBOOT_defconfig
> index 2f933e6cab..37d6767f28 100644
> --- a/configs/TQM5200_B_HIGHBOOT_defconfig
> +++ b/configs/TQM5200_B_HIGHBOOT_defconfig
> @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/TQM5200_B_defconfig b/configs/TQM5200_B_defconfig
> index f204484f59..5e0cf9ea47 100644
> --- a/configs/TQM5200_B_defconfig
> +++ b/configs/TQM5200_B_defconfig
> @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/TQM5200_STK100_defconfig b/configs/TQM5200_STK100_defconfig
> index db9bb8a30d..7b4b030d74 100644
> --- a/configs/TQM5200_STK100_defconfig
> +++ b/configs/TQM5200_STK100_defconfig
> @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/TQM5200_defconfig b/configs/TQM5200_defconfig
> index eec60f1be4..4792639653 100644
> --- a/configs/TQM5200_defconfig
> +++ b/configs/TQM5200_defconfig
> @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -18,7 +17,6 @@ CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/a4m072_defconfig b/configs/a4m072_defconfig
> index ce5edcbf01..0054d4cddb 100644
> --- a/configs/a4m072_defconfig
> +++ b/configs/a4m072_defconfig
> @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
> CONFIG_AUTOBOOT_KEYED=y
> CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
> CONFIG_AUTOBOOT_DELAY_STR="asdfg"
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> diff --git a/configs/ac14xx_defconfig b/configs/ac14xx_defconfig
> index e3b7793e04..930ec8acf2 100644
> --- a/configs/ac14xx_defconfig
> +++ b/configs/ac14xx_defconfig
> @@ -5,7 +5,6 @@ CONFIG_FIT=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_SYS_PROMPT="ac14xx> "
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/ap_sh4a_4a_defconfig b/configs/ap_sh4a_4a_defconfig
> index 75cf53fe21..41c8be9120 100644
> --- a/configs/ap_sh4a_4a_defconfig
> +++ b/configs/ap_sh4a_4a_defconfig
> @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
> # CONFIG_CMD_ENV_EXISTS is not set
> # CONFIG_CMD_LOADB is not set
> # CONFIG_CMD_LOADS is not set
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_FPGA is not set
> # CONFIG_CMD_ECHO is not set
> # CONFIG_CMD_ITEST is not set
> diff --git a/configs/apx4devkit_defconfig b/configs/apx4devkit_defconfig
> index e2061a2cce..5c30fe3ce7 100644
> --- a/configs/apx4devkit_defconfig
> +++ b/configs/apx4devkit_defconfig
> @@ -14,14 +14,12 @@ CONFIG_HUSH_PARSER=y
> # CONFIG_CMD_IMLS is not set
> # CONFIG_CMD_FLASH is not set
> CONFIG_CMD_MMC=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_CACHE=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_UBI=y
> diff --git a/configs/aria_defconfig b/configs/aria_defconfig
> index 963661ab2d..0f1432f9a8 100644
> --- a/configs/aria_defconfig
> +++ b/configs/aria_defconfig
> @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> diff --git a/configs/aspenite_defconfig b/configs/aspenite_defconfig
> index 26654426ed..0ac39eabd2 100644
> --- a/configs/aspenite_defconfig
> +++ b/configs/aspenite_defconfig
> @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
> CONFIG_BOARD_EARLY_INIT_F=y
> # CONFIG_CMD_IMLS is not set
> # CONFIG_CMD_FLASH is not set
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> # CONFIG_CMD_NET is not set
> # CONFIG_CMD_NFS is not set
> diff --git a/configs/cam5200_defconfig b/configs/cam5200_defconfig
> index 92985ab3d6..46a24f56ab 100644
> --- a/configs/cam5200_defconfig
> +++ b/configs/cam5200_defconfig
> @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_MAC_PARTITION=y
> CONFIG_DOS_PARTITION=y
> CONFIG_ISO_PARTITION=y
> diff --git a/configs/cam5200_niosflash_defconfig b/configs/cam5200_niosflash_defconfig
> index 32bc58ee9b..6b9877ff21 100644
> --- a/configs/cam5200_niosflash_defconfig
> +++ b/configs/cam5200_niosflash_defconfig
> @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_MAC_PARTITION=y
> CONFIG_DOS_PARTITION=y
> CONFIG_ISO_PARTITION=y
> diff --git a/configs/charon_defconfig b/configs/charon_defconfig
> index ec22a6368f..8a1429037a 100644
> --- a/configs/charon_defconfig
> +++ b/configs/charon_defconfig
> @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> diff --git a/configs/cm5200_defconfig b/configs/cm5200_defconfig
> index 7d8d01aaaa..d3369f4455 100644
> --- a/configs/cm5200_defconfig
> +++ b/configs/cm5200_defconfig
> @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5
> CONFIG_SILENT_CONSOLE=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> diff --git a/configs/digsy_mtc_RAMBOOT_defconfig b/configs/digsy_mtc_RAMBOOT_defconfig
> index 0d11eec75a..86b2b0d804 100644
> --- a/configs/digsy_mtc_RAMBOOT_defconfig
> +++ b/configs/digsy_mtc_RAMBOOT_defconfig
> @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
> CONFIG_AUTOBOOT_DELAY_STR="d"
> CONFIG_AUTOBOOT_STOP_STR=" "
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_CACHE=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/digsy_mtc_defconfig b/configs/digsy_mtc_defconfig
> index dc17ab4406..85b7f850f7 100644
> --- a/configs/digsy_mtc_defconfig
> +++ b/configs/digsy_mtc_defconfig
> @@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y
> CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
> CONFIG_AUTOBOOT_DELAY_STR=" "
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -19,7 +18,6 @@ CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_CACHE=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/digsy_mtc_rev5_RAMBOOT_defconfig b/configs/digsy_mtc_rev5_RAMBOOT_defconfig
> index 4ab11c755b..7ec8650aca 100644
> --- a/configs/digsy_mtc_rev5_RAMBOOT_defconfig
> +++ b/configs/digsy_mtc_rev5_RAMBOOT_defconfig
> @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
> CONFIG_AUTOBOOT_DELAY_STR="d"
> CONFIG_AUTOBOOT_STOP_STR=" "
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_CACHE=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/digsy_mtc_rev5_defconfig b/configs/digsy_mtc_rev5_defconfig
> index 1f3f3c8bb6..b4b8533063 100644
> --- a/configs/digsy_mtc_rev5_defconfig
> +++ b/configs/digsy_mtc_rev5_defconfig
> @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
> CONFIG_AUTOBOOT_DELAY_STR="d"
> CONFIG_AUTOBOOT_STOP_STR=" "
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_CACHE=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/fo300_defconfig b/configs/fo300_defconfig
> index b4f334a436..00418153be 100644
> --- a/configs/fo300_defconfig
> +++ b/configs/fo300_defconfig
> @@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> @@ -21,7 +20,6 @@ CONFIG_CMD_PING=y
> CONFIG_CMD_SNTP=y
> CONFIG_CMD_BMP=y
> CONFIG_CMD_BSP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> diff --git a/configs/gplugd_defconfig b/configs/gplugd_defconfig
> index 97bb976803..f44b68dae8 100644
> --- a/configs/gplugd_defconfig
> +++ b/configs/gplugd_defconfig
> @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
> CONFIG_BOARD_EARLY_INIT_F=y
> # CONFIG_CMD_IMLS is not set
> # CONFIG_CMD_FLASH is not set
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_FPGA is not set
> # CONFIG_CMD_SETEXPR is not set
> diff --git a/configs/ipek01_defconfig b/configs/ipek01_defconfig
> index cac9326b6c..690bc0f461 100644
> --- a/configs/ipek01_defconfig
> +++ b/configs/ipek01_defconfig
> @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
> # CONFIG_CONSOLE_MUX is not set
> CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_LOOPW=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_BMP=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_FAT=y
> # CONFIG_MMC is not set
> CONFIG_MTD_NOR_FLASH=y
> diff --git a/configs/m28evk_defconfig b/configs/m28evk_defconfig
> index 6acbd77d5f..0ab7f6bb3c 100644
> --- a/configs/m28evk_defconfig
> +++ b/configs/m28evk_defconfig
> @@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y
> CONFIG_CMD_MMC=y
> CONFIG_CMD_SF=y
> CONFIG_CMD_SPI=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> CONFIG_CMD_GPIO=y
> CONFIG_CMD_DHCP=y
> diff --git a/configs/mecp5123_defconfig b/configs/mecp5123_defconfig
> index ebf5415464..db52077e1a 100644
> --- a/configs/mecp5123_defconfig
> +++ b/configs/mecp5123_defconfig
> @@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_FAT=y
> # CONFIG_MMC is not set
> CONFIG_MTD_NOR_FLASH=y
> diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig
> index 91384a6259..5040ea5742 100644
> --- a/configs/motionpro_defconfig
> +++ b/configs/motionpro_defconfig
> @@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y
> CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
> CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_BEDBUG=y
> CONFIG_LED_STATUS=y
> diff --git a/configs/mpc5121ads_defconfig b/configs/mpc5121ads_defconfig
> index c0af8127b5..47c4e5ace7 100644
> --- a/configs/mpc5121ads_defconfig
> +++ b/configs/mpc5121ads_defconfig
> @@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_MAC_PARTITION=y
> diff --git a/configs/mpc5121ads_rev2_defconfig b/configs/mpc5121ads_rev2_defconfig
> index ad46e02e94..ef700d0773 100644
> --- a/configs/mpc5121ads_rev2_defconfig
> +++ b/configs/mpc5121ads_rev2_defconfig
> @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_EXT2=y
> CONFIG_CMD_FAT=y
> CONFIG_MAC_PARTITION=y
> diff --git a/configs/pcm030_LOWBOOT_defconfig b/configs/pcm030_LOWBOOT_defconfig
> index d19908ca8f..2933326e5d 100644
> --- a/configs/pcm030_LOWBOOT_defconfig
> +++ b/configs/pcm030_LOWBOOT_defconfig
> @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
> CONFIG_BOOTDELAY=3
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> -CONFIG_CMD_DATE=y
> # CONFIG_MMC is not set
> CONFIG_MTD_NOR_FLASH=y
> CONFIG_USB=y
> diff --git a/configs/pcm030_defconfig b/configs/pcm030_defconfig
> index ef5c85888c..ff9f4e9f4f 100644
> --- a/configs/pcm030_defconfig
> +++ b/configs/pcm030_defconfig
> @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
> CONFIG_OF_BOARD_SETUP=y
> CONFIG_BOOTDELAY=3
> CONFIG_SYS_PROMPT="uboot> "
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> -CONFIG_CMD_DATE=y
> # CONFIG_MMC is not set
> CONFIG_MTD_NOR_FLASH=y
> CONFIG_USB=y
> diff --git a/configs/pdm360ng_defconfig b/configs/pdm360ng_defconfig
> index f45a90caf9..4ef0df1aa8 100644
> --- a/configs/pdm360ng_defconfig
> +++ b/configs/pdm360ng_defconfig
> @@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y
> # CONFIG_CONSOLE_MUX is not set
> CONFIG_HUSH_PARSER=y
> CONFIG_CMD_ASKENV=y
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> CONFIG_CMD_BMP=y
> -CONFIG_CMD_DATE=y
> # CONFIG_MMC is not set
> CONFIG_MTD_NOR_FLASH=y
> # CONFIG_PCI is not set
> diff --git a/configs/r0p7734_defconfig b/configs/r0p7734_defconfig
> index c5c3d52718..91b08dc24f 100644
> --- a/configs/r0p7734_defconfig
> +++ b/configs/r0p7734_defconfig
> @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
> # CONFIG_CMD_ENV_EXISTS is not set
> # CONFIG_CMD_LOADB is not set
> # CONFIG_CMD_LOADS is not set
> -CONFIG_CMD_I2C=y
> # CONFIG_CMD_FPGA is not set
> # CONFIG_CMD_ECHO is not set
> # CONFIG_CMD_ITEST is not set
> diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig
> index db4c47c3d2..18dc039d93 100644
> --- a/configs/v38b_defconfig
> +++ b/configs/v38b_defconfig
> @@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y
> CONFIG_TARGET_V38B=y
> CONFIG_BOOTDELAY=3
> CONFIG_BOARD_EARLY_INIT_F=y
> -CONFIG_CMD_I2C=y
> CONFIG_CMD_USB=y
> # CONFIG_CMD_SETEXPR is not set
> CONFIG_CMD_DHCP=y
> CONFIG_CMD_MII=y
> CONFIG_CMD_PING=y
> -CONFIG_CMD_DATE=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_DIAG=y
> CONFIG_MAC_PARTITION=y
> diff --git a/include/common.h b/include/common.h
> index 83e4037a86..45f190a600 100644
> --- a/include/common.h
> +++ b/include/common.h
> @@ -499,9 +499,19 @@ void reset_phy (void);
> void fdc_hw_init (void);
>
> /* $(BOARD)/eeprom.c */
> +#ifdef CONFIG_CMD_EEPROM
> void eeprom_init (int bus);
> int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
> int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
> +#else
> +/*
> + * Some EEPROM code is depecated because it used the legacy I2C interface. Add
> + * some macros here so we don't have to touch every one of those uses
> + */
> +#define eeprom_init(bus)
> +#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
> +#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
> +#endif
>
> /*
> * Set this up regardless of board
> diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h
> index 1817571efe..7b162cccef 100644
> --- a/include/configs/M54418TWR.h
> +++ b/include/configs/M54418TWR.h
> @@ -166,7 +166,6 @@
>
> /* I2c */
> #undef CONFIG_SYS_FSL_I2C
> -#undef CONFIG_HARD_I2C /* I2C with hardware support */
> #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
> /* I2C speed and slave address */
> #define CONFIG_SYS_I2C_SPEED 80000
> diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
> index 13f4ef67e1..19e0b1be1b 100644
> --- a/include/configs/TQM5200.h
> +++ b/include/configs/TQM5200.h
> @@ -124,8 +124,7 @@
> #ifndef CONFIG_CAM5200
> /* POST support */
> #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
> - CONFIG_SYS_POST_CPU | \
> - CONFIG_SYS_POST_I2C)
> + CONFIG_SYS_POST_CPU)
> #endif
>
> #ifdef CONFIG_POST
> @@ -144,7 +143,6 @@
> /*
> * Command line configuration.
> */
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_JFFS2
> #define CONFIG_CMD_REGINFO
>
> @@ -278,54 +276,6 @@
> #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
> #endif
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#ifdef CONFIG_TQM5200_REV100
> -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
> -#else
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
> -#endif
> -
> -/*
> - * I2C clock frequency
> - *
> - * Please notice, that the resulting clock frequency could differ from the
> - * configured value. This is because the I2C clock is derived from system
> - * clock over a frequency divider with only a few divider values. U-Boot
> - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
> - * approximation allways lies below the configured value, never above.
> - */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
> - * also). For other EEPROMs configuration should be verified. On Mini-FAP the
> - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
> - * same configuration could be used.
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
> -
> -/*
> - * HW-Monitor configuration on Mini-FAP
> - */
> -#if defined (CONFIG_MINIFAP)
> -#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C
> -#endif
> -
> -/* List of I2C addresses to be verified by POST */
> -#if defined (CONFIG_MINIFAP)
> -#undef CONFIG_SYS_POST_I2C_ADDRS
> -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
> - CONFIG_SYS_I2C_HWMON_ADDR, \
> - CONFIG_SYS_I2C_SLAVE}
> -#endif
> -
> /*
> * Flash configuration
> */
> @@ -544,18 +494,6 @@
> #endif
> #endif
>
> -/*
> - * RTC configuration
> - */
> -#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
> -# define CONFIG_RTC_M41T11 1
> -# define CONFIG_SYS_I2C_RTC_ADDR 0x68
> -# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
> - year */
> -#else
> -# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
> -#endif
> -
> /*
> * Miscellaneous configurable options
> */
> diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h
> index 79099518e7..2ea43ffce1 100644
> --- a/include/configs/a4m072.h
> +++ b/include/configs/a4m072.h
> @@ -81,7 +81,6 @@
> /*
> * Command line configuration.
> */
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_IDE
>
> #if defined(CONFIG_PCI)
> @@ -145,25 +144,6 @@
> */
> #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
> -
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
> -#define CONFIG_SYS_EEPROM_WREN 1
> -#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4
> -
> /*
> * Flash configuration
> */
> diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h
> index ee015bb83d..2a46e9b864 100644
> --- a/include/configs/ac14xx.h
> +++ b/include/configs/ac14xx.h
> @@ -336,28 +336,11 @@
>
> #define CONFIG_CMDLINE_EDITING 1 /* command line history */
>
> -/* I2C */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_I2C_MULTI_BUS
> -
> -/* I2C speed and slave address */
> -#define CONFIG_SYS_I2C_SPEED 100000
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> /*
> * IIM - IC Identification Module
> */
> #undef CONFIG_FSL_IIM
>
> -/*
> - * EEPROM configuration for Atmel AT24C01:
> - * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
> -
> /*
> * Ethernet configuration
> */
> @@ -384,7 +367,6 @@
> #define CONFIG_LOADS_ECHO 1
> #define CONFIG_SYS_LOADS_BAUD_CHANGE 1
>
> -#define CONFIG_CMD_EEPROM
> #undef CONFIG_CMD_FUSE
> #undef CONFIG_CMD_IDE
> #define CONFIG_CMD_JFFS2
> diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h
> index 5f5882dc8e..d3d72b634d 100644
> --- a/include/configs/ap_sh4a_4a.h
> +++ b/include/configs/ap_sh4a_4a.h
> @@ -35,20 +35,6 @@
> #define CONFIG_BITBANGMII
> #define CONFIG_BITBANGMII_MULTI
>
> -/* I2C */
> -#define CONFIG_SH_SH7734_I2C 1
> -#define CONFIG_HARD_I2C 1
> -#define CONFIG_I2C_MULTI_BUS 1
> -#define CONFIG_SYS_MAX_I2C_BUS 2
> -#define CONFIG_SYS_I2C_MODULE 0
> -#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x50
> -#define CONFIG_SH_I2C_DATA_HIGH 4
> -#define CONFIG_SH_I2C_DATA_LOW 5
> -#define CONFIG_SH_I2C_CLOCK 500000000
> -#define CONFIG_SH_I2C_BASE0 0xFFC70000
> -#define CONFIG_SH_I2C_BASE1 0xFFC71000
> -
> /* undef to save memory */
> #define CONFIG_SYS_LONGHELP
> /* Monitor Command Prompt */
> diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h
> index a4c7847dab..cce39f27c7 100644
> --- a/include/configs/apx4devkit.h
> +++ b/include/configs/apx4devkit.h
> @@ -79,12 +79,6 @@
> #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
> #endif
>
> -/* RTC */
> -#ifdef CONFIG_CMD_DATE
> -#define CONFIG_RTC_PCF8563
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x51
> -#endif
> -
> /* Boot Linux */
> #define CONFIG_BOOTFILE "uImage"
> #define CONFIG_BOOTCOMMAND "run bootcmd_nand"
> diff --git a/include/configs/aria.h b/include/configs/aria.h
> index 94f6605d46..4d946fc44a 100644
> --- a/include/configs/aria.h
> +++ b/include/configs/aria.h
> @@ -340,31 +340,11 @@
>
> #endif
>
> -/* I2C */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_I2C_MULTI_BUS
> -
> -/* I2C speed and slave address */
> -#define CONFIG_SYS_I2C_SPEED 100000
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -#if 0
> -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
> -#endif
> -
> /*
> * IIM - IC Identification Module
> */
> #undef CONFIG_FSL_IIM
>
> -/*
> - * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
> - * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
> -
> /*
> * Ethernet configuration
> */
> @@ -392,7 +372,6 @@
> #define CONFIG_LOADS_ECHO 1
> #define CONFIG_SYS_LOADS_BAUD_CHANGE 1
>
> -#define CONFIG_CMD_EEPROM
> #undef CONFIG_CMD_FUSE
> #undef CONFIG_CMD_IDE
> #define CONFIG_CMD_JFFS2
> diff --git a/include/configs/axs10x.h b/include/configs/axs10x.h
> index 768e8fbfa4..66e8cd5e9a 100644
> --- a/include/configs/axs10x.h
> +++ b/include/configs/axs10x.h
> @@ -100,7 +100,7 @@
> /*
> * Environment settings
> */
> -#define CONFIG_ENV_IS_IN_EEPROM
> +#define CONFIG_ENV_IS_NOWHERE
> #define CONFIG_ENV_SIZE SZ_512
> #define CONFIG_ENV_OFFSET 0
>
> diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
> index 0073cb5373..3a7d826837 100644
> --- a/include/configs/cm5200.h
> +++ b/include/configs/cm5200.h
> @@ -44,7 +44,7 @@
> /*
> * POST support
> */
> -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
> +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU)
> #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
> /* List of I2C addresses to be verified by POST */
> #define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \
> @@ -199,16 +199,6 @@
> "2m(kernel),27904k(rootfs)," \
> "-(config)"
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
> -#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x0
> -#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */
> -#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */
> -
> /*
> * RTC configuration
> */
> diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h
> index 2b56945dd9..ab546c50cd 100644
> --- a/include/configs/digsy_mtc.h
> +++ b/include/configs/digsy_mtc.h
> @@ -85,7 +85,6 @@
> /*
> * Command line configuration.
> */
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_IDE
> #define CONFIG_CMD_IRQ
> #define CONFIG_CMD_PCI
> @@ -205,36 +204,6 @@
>
> #define CONFIG_BOOTCOMMAND "run mtcb_start"
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1
> -#define CONFIG_SYS_I2C_MODULE 1
> -#define CONFIG_SYS_I2C_SPEED 100000
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
> -
> -/*
> - * RTC configuration
> - */
> -#if defined(CONFIG_DIGSY_REV5)
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x56
> -#define CONFIG_RTC_RV3029
> -/* Enable 5k Ohm trickle charge resistor */
> -#define CONFIG_SYS_RV3029_TCR 0x20
> -#else
> -#define CONFIG_RTC_DS1337
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x68
> -#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */
> -#endif
> -
> /*
> * Flash configuration
> */
> diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
> index 6b6bbbd5c0..7ffc9d1dd9 100644
> --- a/include/configs/ids8313.h
> +++ b/include/configs/ids8313.h
> @@ -165,7 +165,6 @@
> #define CONFIG_TSEC2
> #define CONFIG_TSEC_ENET
> #define CONFIG_HARD_SPI
> -#define CONFIG_HARD_I2C
>
> /*
> * NOR FLASH setup
> diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h
> index aff4adf5d0..ece72c6aa1 100644
> --- a/include/configs/ipek01.h
> +++ b/include/configs/ipek01.h
> @@ -150,29 +150,6 @@
> #define OF_SOC "soc5200 at f0000000"
> #define OF_TBCLK (bd->bi_busfreq / 4)
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
> -
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
> -
> -/*
> - * RTC configuration
> - */
> -#define CONFIG_RTC_PCF8563
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x51
> -
> #define CONFIG_SYS_FLASH_BASE 0xFC000000
> #define CONFIG_SYS_FLASH_SIZE 0x01000000
> #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
> diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h
> index 0d97317c7f..4461623118 100644
> --- a/include/configs/jupiter.h
> +++ b/include/configs/jupiter.h
> @@ -127,25 +127,6 @@
> #define OF_STDOUT_PATH "/soc5200 at f0000000/serial at 2000"
> #endif
>
> -#if 0
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
> -
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
> -#endif
> -
> /*
> * Flash configuration
> */
> diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
> index f6fa599e6b..c4717238bb 100644
> --- a/include/configs/m28evk.h
> +++ b/include/configs/m28evk.h
> @@ -16,7 +16,6 @@
> /* U-Boot Commands */
> #define CONFIG_FAT_WRITE
>
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_NAND
> #define CONFIG_CMD_NAND_TRIMFFS
>
> @@ -63,11 +62,6 @@
> #define CONFIG_FEC_MXC
> #endif
>
> -/* EEPROM */
> -#ifdef CONFIG_CMD_EEPROM
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> -#endif
> -
> /* RTC */
> #ifdef CONFIG_CMD_DATE
> /* Use the internal RTC in the MXS chip */
> diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h
> new file mode 100644
> index 0000000000..68874dc029
> --- /dev/null
> +++ b/include/configs/manroland/mpc5200-common.h
> @@ -0,0 +1,176 @@
> +/*
> + * (C) Copyright 2009
> + * Heiko Schocher, DENX Software Engineering, hs at denx.de.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __MANROLAND_MPC52XX__COMMON_H
> +#define __MANROLAND_MPC52XX__COMMON_H
> +
> +/*
> + * High Level Configuration Options
> + * (easy to change)
> + */
> +#define CONFIG_MPC5200 1 /* MPC5200 CPU */
> +
> +/* ... running at 33.000000MHz */
> +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
> +
> +#define CONFIG_HIGH_BATS 1 /* High BATs supported */
> +
> +/*
> + * Serial console configuration
> + */
> +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
> +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\
> + 230400 }
> +
> +#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
> +# define CONFIG_SYS_LOWBOOT 1
> +#endif
> +
> +/*
> + * IPB Bus clocking configuration.
> + */
> +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
> +
> +/*
> + * Flash configuration
> + */
> +#define CONFIG_SYS_FLASH_BASE 0xFF800000
> +
> +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
> +
> +#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
> +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
> + (= chip selects) */
> +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/
> +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/
> +
> +#define CONFIG_FLASH_CFI_DRIVER
> +#define CONFIG_SYS_FLASH_CFI
> +#define CONFIG_SYS_FLASH_EMPTY_INFO
> +#define CONFIG_SYS_FLASH_CFI_AMD_RESET
> +
> +/*
> + * Environment settings
> + */
> +#define CONFIG_ENV_IS_IN_FLASH 1
> +#define CONFIG_ENV_SIZE 0x4000
> +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
> +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
> +
> +/*
> + * Memory map
> + */
> +#define CONFIG_SYS_MBAR 0xF0000000
> +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
> +
> +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
> + GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
> +
> +#define CONFIG_SYS_SDRAM_BASE 0x00000000
> +#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */
> +#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */
> +
> +/* Settings for XLB = 132 MHz */
> +#define SDRAM_DDR 1
> +#define SDRAM_MODE 0x018D0000
> +#define SDRAM_EMODE 0x40090000
> +#define SDRAM_CONTROL 0x714f0f00
> +#define SDRAM_CONFIG1 0x73722930
> +#define SDRAM_CONFIG2 0x47770000
> +#define SDRAM_TAPDELAY 0x10000000
> +
> +/* Use ON-Chip SRAM until RAM will be available */
> +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
> +#ifdef CONFIG_POST
> +/* preserve space for the post_word at end of on-chip SRAM */
> +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
> +#else
> +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
> +#endif
> +
> +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
> +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
> +# define CONFIG_SYS_RAMBOOT 1
> +#endif
> +
> +#define CONFIG_SYS_MONITOR_LEN (192 << 10)
> +#define CONFIG_SYS_MALLOC_LEN (512 << 10)
> +#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
> +
> +/*
> + * Ethernet configuration
> + */
> +#define CONFIG_MPC5xxx_FEC 1
> +#define CONFIG_MPC5xxx_FEC_MII100
> +#define CONFIG_PHY_ADDR 0x00
> +#define CONFIG_MII 1
> +
> +/*use Hardware WDT */
> +#define CONFIG_HW_WATCHDOG
> +
> +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
> +#if defined(CONFIG_CMD_KGDB)
> +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
> +#endif
> +
> +/*
> + * Various low-level settings
> + */
> +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
> +#define CONFIG_SYS_HID0_FINAL HID0_ICE
> +
> +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
> +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
> +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
> +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
> +
> +/* 8Mbit SRAM @0x80100000 */
> +#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE
> +
> +#define CONFIG_SYS_CS_BURST 0x00000000
> +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
> +
> +/*-----------------------------------------------------------------------
> + * IDE/ATA stuff Supports IDE harddisk
> + *-----------------------------------------------------------------------
> + */
> +
> +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
> +
> +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
> +#undef CONFIG_IDE_LED /* LED for ide not supported */
> +
> +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
> +
> +#define CONFIG_IDE_PREINIT 1
> +
> +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
> +
> +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
> +
> +/* Offset for data I/O */
> +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
> +
> +/* Offset for normal register accesses */
> +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
> +
> +/* Offset for alternate registers */
> +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
> +
> +/* Interval between registers */
> +#define CONFIG_SYS_ATA_STRIDE 4
> +
> +#define CONFIG_ATAPI 1
> +
> +#define OF_CPU "PowerPC,5200 at 0"
> +#define OF_SOC "soc5200 at f0000000"
> +#define OF_TBCLK (bd->bi_busfreq / 4)
> +#define OF_STDOUT_PATH "/soc5200 at f0000000/serial at 2000"
> +#define CONFIG_OF_IDE_FIXUP
> +
> +#endif /* __MANROLAND_MPC52XX__COMMON_H */
> diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h
> index 1a9cb675df..fe94e663c5 100644
> --- a/include/configs/mecp5123.h
> +++ b/include/configs/mecp5123.h
> @@ -241,26 +241,11 @@
>
> #define CONFIG_CMDLINE_EDITING 1 /* add command line history */
>
> -/* I2C */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
> -
> /*
> * IIM - IC Identification Module
> */
> #undef CONFIG_FSL_IIM
>
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
> -#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */
> -
> /*
> * Ethernet configuration
> */
> @@ -280,7 +265,7 @@
> /*
> * Environment
> */
> -#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */
> +#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */
> #define CONFIG_ENV_SIZE 0x1000
> #define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */
>
> @@ -288,7 +273,6 @@
> #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
>
> #define CONFIG_CMD_REGINFO
> -#define CONFIG_CMD_EEPROM
> #undef CONFIG_CMD_FUSE
> #undef CONFIG_CMD_IDE
> #define CONFIG_CMD_JFFS2
> diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
> index 136db0dd26..cb5c346807 100644
> --- a/include/configs/motionpro.h
> +++ b/include/configs/motionpro.h
> @@ -34,7 +34,6 @@
> * Command line configuration.
> */
> #define CONFIG_CMD_DTT
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_IDE
> #define CONFIG_CMD_IMMAP
> #define CONFIG_CMD_JFFS2
> @@ -255,21 +254,6 @@
> #define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
> #define CONFIG_SYS_ATA_STRIDE 4
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
> -
> /*
> * RTC configuration
> */
> @@ -283,12 +267,6 @@
> #define ENABLE_GPIO_OUT 0x00000024
> #define LED_ON 0x00000010
>
> -/*
> - * Temperature sensor
> - */
> -#define CONFIG_DTT_LM75 1
> -#define CONFIG_DTT_SENSORS { 0x49 }
> -
> /*
> * Environment settings
> */
> diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h
> index dafb724e3f..f3961a6f35 100644
> --- a/include/configs/mpc5121ads.h
> +++ b/include/configs/mpc5121ads.h
> @@ -327,28 +327,11 @@
>
> #endif
>
> -/* I2C */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -#if 0
> -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
> -#endif
> -
> /*
> * IIM - IC Identification Module
> */
> #undef CONFIG_FSL_IIM
>
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
> -
> /*
> * Ethernet configuration
> */
> @@ -396,7 +379,6 @@
> #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
> #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
>
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_IDE
> #define CONFIG_CMD_JFFS2
> #define CONFIG_CMD_REGINFO
> diff --git a/include/configs/mxs.h b/include/configs/mxs.h
> index fdf596f82f..c403dda483 100644
> --- a/include/configs/mxs.h
> +++ b/include/configs/mxs.h
> @@ -126,16 +126,6 @@
> #endif
> #endif
>
> -/* I2C */
> -#ifdef CONFIG_CMD_I2C
> -#define CONFIG_SYS_I2C
> -#define CONFIG_SYS_I2C_MXS
> -#define CONFIG_HARD_I2C
> -#ifndef CONFIG_SYS_I2C_SPEED
> -#define CONFIG_SYS_I2C_SPEED 400000
> -#endif
> -#endif
> -
> /* LCD */
> #ifdef CONFIG_VIDEO
> #define CONFIG_VIDEO_MXS
> diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h
> index e2881a7177..1b4200bcbf 100644
> --- a/include/configs/o2dnt-common.h
> +++ b/include/configs/o2dnt-common.h
> @@ -68,7 +68,6 @@
> /*
> * Supported commands
> */
> -#define CONFIG_CMD_EEPROM
> #ifdef CONFIG_PCI
> #define CONFIG_CMD_PCI
> #endif
> @@ -172,27 +171,6 @@
> #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
> #endif
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration:
> - *
> - * O2DNT board is equiped with Ramtron FRAM device FM24CL16
> - * 16 Kib Ferroelectric Nonvolatile serial RAM memory
> - * organized as 2048 x 8 bits and addressable as eight I2C devices
> - * 0x50 ... 0x57 each 256 bytes in size
> - *
> - */
> -#define CONFIG_SYS_I2C_FRAM
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
> /*
> * There is no write delay with FRAM, write operations are performed at bus
> * speed. Thus, no status polling or write delay is needed.
> diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h
> index 6d8a2338a2..406f3e547a 100644
> --- a/include/configs/pcm030.h
> +++ b/include/configs/pcm030.h
> @@ -49,7 +49,6 @@ Serial console configuration
> /*
> * Command line configuration.
> */
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_JFFS2
> #define CONFIG_CMD_PCI
>
> @@ -120,31 +119,6 @@ IPB Bus clocking configuration.
> #define CONFIG_PCI_IO_SIZE 0x01000000
> #define CONFIG_SYS_XLB_PIPELINING 1
>
> -/*---------------------------------------------------------------------------
> - I2C configuration
> ----------------------------------------------------------------------------*/
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*---------------------------------------------------------------------------
> - EEPROM CAT24WC32 configuration
> ----------------------------------------------------------------------------*/
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
> -#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
> -#define CONFIG_SYS_EEPROM_SIZE 2048
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
> -
> -/*---------------------------------------------------------------------------
> -RTC configuration
> ----------------------------------------------------------------------------*/
> -#define RTC
> -#define CONFIG_RTC_PCF8563 1
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x51
> -
> /*---------------------------------------------------------------------------
> Flash configuration
> ---------------------------------------------------------------------------*/
> @@ -172,11 +146,10 @@ RTC configuration
> Environment settings
> ---------------------------------------------------------------------------*/
>
> -/* pcm030 ships with environment is EEPROM by default */
> -#define CONFIG_ENV_IS_IN_EEPROM 1
> +#define CONFIG_ENV_IS_NOWHERE
> #define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
> /*beginning of the EEPROM */
> -#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
> +#define CONFIG_ENV_SIZE 2048
>
> #define CONFIG_ENV_OVERWRITE 1
>
> diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h
> index 501611dde7..4bd8236b33 100644
> --- a/include/configs/pdm360ng.h
> +++ b/include/configs/pdm360ng.h
> @@ -301,34 +301,11 @@
> #define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000
> #define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400
>
> -/*
> - * I2C
> - */
> -#define CONFIG_HARD_I2C /* I2C with hardware support */
> -#define CONFIG_I2C_MULTI_BUS
> -#define CONFIG_I2C_CMD_TREE
> -/* I2C speed and slave address */
> -#define CONFIG_SYS_I2C_SPEED 100000
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> /*
> * IIM - IC Identification Module
> */
> #undef CONFIG_FSL_IIM
>
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */
> -
> -/*
> - * MAC addr in EEPROM
> - */
> -#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0
> -#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10
> /*
> * Enabled only to delete "ethaddr" before testing
> * "ethaddr" setting from EEPROM
> @@ -344,12 +321,6 @@
> #define CONFIG_FEC_AN_TIMEOUT 1
> #define CONFIG_HAS_ETH0
>
> -/*
> - * Configure on-board RTC
> - */
> -#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
> -
> /*
> * Environment
> */
> @@ -367,7 +338,6 @@
> #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
> #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
>
> -#define CONFIG_CMD_EEPROM
> #define CONFIG_CMD_REGINFO
>
> #undef CONFIG_CMD_FUSE
> diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h
> index 642572fc95..b159b1ed8d 100644
> --- a/include/configs/r0p7734.h
> +++ b/include/configs/r0p7734.h
> @@ -40,20 +40,6 @@
> # define CONFIG_SMC911X_BASE (0x84000000)
> #endif
>
> -/* I2C */
> -#define CONFIG_SH_SH7734_I2C 1
> -#define CONFIG_HARD_I2C 1
> -#define CONFIG_I2C_MULTI_BUS 1
> -#define CONFIG_SYS_MAX_I2C_BUS 2
> -#define CONFIG_SYS_I2C_MODULE 0
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x50
> -#define CONFIG_SH_I2C_DATA_HIGH 4
> -#define CONFIG_SH_I2C_DATA_LOW 5
> -#define CONFIG_SH_I2C_CLOCK 500000000
> -#define CONFIG_SH_I2C_BASE0 0xFFC70000
> -#define CONFIG_SH_I2C_BASE1 0xFFC7100
> -
> /* undef to save memory */
> #define CONFIG_SYS_LONGHELP
> /* Monitor Command Prompt */
> diff --git a/include/configs/s32v234evb.h b/include/configs/s32v234evb.h
> index 398b3aa343..33487cd86f 100644
> --- a/include/configs/s32v234evb.h
> +++ b/include/configs/s32v234evb.h
> @@ -97,16 +97,6 @@
> #define CONFIG_PHY_MICREL
> #endif
>
> -#if 0 /* Disable until the I2C driver will be updated */
> -
> -/* I2C Configs */
> -#define CONFIG_CMD_I2C
> -#define CONFIG_HARD_I2C
> -#define CONFIG_I2C_MXC
> -#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR
> -#define CONFIG_SYS_I2C_SPEED 100000
> -#endif
> -
> #if 0 /* Disable until the FLASH will be implemented */
> #define CONFIG_SYS_USE_NAND
> #endif
> diff --git a/include/configs/v38b.h b/include/configs/v38b.h
> index cc0007827d..0bc0ae517a 100644
> --- a/include/configs/v38b.h
> +++ b/include/configs/v38b.h
> @@ -134,27 +134,6 @@
> */
> #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
>
> -/*
> - * I2C configuration
> - */
> -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
> -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> -#define CONFIG_SYS_I2C_SLAVE 0x7F
> -
> -/*
> - * EEPROM configuration
> - */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
> -
> -/*
> - * RTC configuration
> - */
> -#define CONFIG_SYS_I2C_RTC_ADDR 0x51
> -
> /*
> * Flash configuration - use CFI driver
> */
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C
2017-05-13 3:09 ` [U-Boot] [PATCH v3 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C Simon Glass
@ 2017-05-15 4:23 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:23 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option for powerpc.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> arch/powerpc/cpu/mpc512x/Makefile | 1 -
> arch/powerpc/cpu/mpc512x/i2c.c | 386 -------------------
> arch/powerpc/cpu/mpc5xxx/Makefile | 1 -
> arch/powerpc/cpu/mpc5xxx/i2c.c | 456 ----------------------
> arch/powerpc/cpu/mpc8260/Makefile | 2 +-
> arch/powerpc/cpu/mpc8260/commproc.c | 4 -
> arch/powerpc/cpu/mpc8260/i2c.c | 741 ------------------------------------
> arch/powerpc/cpu/mpc8xx/Makefile | 1 -
> arch/powerpc/cpu/mpc8xx/i2c.c | 672 --------------------------------
> board/freescale/m52277evb/README | 1 -
> board/freescale/m53017evb/README | 1 -
> board/freescale/m5373evb/README | 1 -
> board/freescale/m54455evb/README | 1 -
> board/freescale/m547xevb/README | 1 -
> 14 files changed, 1 insertion(+), 2268 deletions(-)
> delete mode 100644 arch/powerpc/cpu/mpc512x/i2c.c
> delete mode 100644 arch/powerpc/cpu/mpc5xxx/i2c.c
> delete mode 100644 arch/powerpc/cpu/mpc8260/i2c.c
> delete mode 100644 arch/powerpc/cpu/mpc8xx/i2c.c
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/arch/powerpc/cpu/mpc512x/Makefile b/arch/powerpc/cpu/mpc512x/Makefile
> index 98991c688b..933deebdae 100644
> --- a/arch/powerpc/cpu/mpc512x/Makefile
> +++ b/arch/powerpc/cpu/mpc512x/Makefile
> @@ -9,7 +9,6 @@ obj-y := cpu.o
> obj-y += traps.o
> obj-y += cpu_init.o
> obj-y += fixed_sdram.o
> -obj-y += i2c.o
> obj-y += interrupts.o
> obj-y += iopin.o
> obj-y += serial.o
> diff --git a/arch/powerpc/cpu/mpc512x/i2c.c b/arch/powerpc/cpu/mpc512x/i2c.c
> deleted file mode 100644
> index 15d519a116..0000000000
> --- a/arch/powerpc/cpu/mpc512x/i2c.c
> +++ /dev/null
> @@ -1,386 +0,0 @@
> -/*
> - * (C) Copyright 2003 - 2009
> - * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> - *
> - * SPDX-License-Identifier: GPL-2.0+
> - *
> - * Based on the MPC5xxx code.
> - */
> -
> -#include <common.h>
> -#include <asm/io.h>
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -#ifdef CONFIG_HARD_I2C
> -
> -#include <i2c.h>
> -
> -/* by default set I2C bus 0 active */
> -static unsigned int bus_num __attribute__ ((section (".data"))) = 0;
> -
> -#define I2C_TIMEOUT 100
> -#define I2C_RETRIES 3
> -
> -struct mpc512x_i2c_tap {
> - int scl2tap;
> - int tap2tap;
> -};
> -
> -static int mpc_reg_in(volatile u32 *reg);
> -static void mpc_reg_out(volatile u32 *reg, int val, int mask);
> -static int wait_for_bb(void);
> -static int wait_for_pin(int *status);
> -static int do_address(uchar chip, char rdwr_flag);
> -static int send_bytes(uchar chip, char *buf, int len);
> -static int receive_bytes(uchar chip, char *buf, int len);
> -static int mpc_get_fdr(int);
> -
> -static int mpc_reg_in (volatile u32 *reg)
> -{
> - int ret = in_be32(reg) >> 24;
> -
> - return ret;
> -}
> -
> -static void mpc_reg_out (volatile u32 *reg, int val, int mask)
> -{
> - if (!mask) {
> - out_be32(reg, val << 24);
> - } else {
> - clrsetbits_be32(reg, mask << 24, (val & mask) << 24);
> - }
> -}
> -
> -static int wait_for_bb (void)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - int timeout = I2C_TIMEOUT;
> - int status;
> -
> - status = mpc_reg_in (®s->msr);
> -
> - while (timeout-- && (status & I2C_BB)) {
> - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
> - (void)mpc_reg_in(®s->mdr);
> - mpc_reg_out (®s->mcr, 0, I2C_STA);
> - mpc_reg_out (®s->mcr, 0, 0);
> - mpc_reg_out (®s->mcr, I2C_EN, 0);
> -
> - udelay (1000);
> - status = mpc_reg_in (®s->msr);
> - }
> -
> - return (status & I2C_BB);
> -}
> -
> -static int wait_for_pin (int *status)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - int timeout = I2C_TIMEOUT;
> -
> - *status = mpc_reg_in (®s->msr);
> -
> - while (timeout-- && !(*status & I2C_IF)) {
> - udelay (1000);
> - *status = mpc_reg_in (®s->msr);
> - }
> -
> - if (!(*status & I2C_IF)) {
> - return -1;
> - }
> -
> - mpc_reg_out (®s->msr, 0, I2C_IF);
> -
> - return 0;
> -}
> -
> -static int do_address (uchar chip, char rdwr_flag)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - int status;
> -
> - chip <<= 1;
> -
> - if (rdwr_flag) {
> - chip |= 1;
> - }
> -
> - mpc_reg_out (®s->mcr, I2C_TX, I2C_TX);
> - mpc_reg_out (®s->mdr, chip, 0);
> -
> - if (wait_for_pin (&status)) {
> - return -2;
> - }
> -
> - if (status & I2C_RXAK) {
> - return -3;
> - }
> -
> - return 0;
> -}
> -
> -static int send_bytes (uchar chip, char *buf, int len)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - int wrcount;
> - int status;
> -
> - for (wrcount = 0; wrcount < len; ++wrcount) {
> -
> - mpc_reg_out (®s->mdr, buf[wrcount], 0);
> -
> - if (wait_for_pin (&status)) {
> - break;
> - }
> -
> - if (status & I2C_RXAK) {
> - break;
> - }
> -
> - }
> -
> - return !(wrcount == len);
> -}
> -
> -static int receive_bytes (uchar chip, char *buf, int len)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - int dummy = 1;
> - int rdcount = 0;
> - int status;
> - int i;
> -
> - mpc_reg_out (®s->mcr, 0, I2C_TX);
> -
> - for (i = 0; i < len; ++i) {
> - buf[rdcount] = mpc_reg_in (®s->mdr);
> -
> - if (dummy) {
> - dummy = 0;
> - } else {
> - rdcount++;
> - }
> -
> - if (wait_for_pin (&status)) {
> - return -4;
> - }
> - }
> -
> - mpc_reg_out (®s->mcr, I2C_TXAK, I2C_TXAK);
> - buf[rdcount++] = mpc_reg_in (®s->mdr);
> -
> - if (wait_for_pin (&status)) {
> - return -5;
> - }
> -
> - mpc_reg_out (®s->mcr, 0, I2C_TXAK);
> -
> - return 0;
> -}
> -
> -/**************** I2C API ****************/
> -
> -void i2c_init (int speed, int saddr)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - int i;
> -
> - for (i = 0; i < I2C_BUS_CNT; i++){
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[i];
> -
> - mpc_reg_out (®s->mcr, 0, 0);
> -
> - /* Set clock */
> - mpc_reg_out (®s->mfdr, mpc_get_fdr (speed), 0);
> - mpc_reg_out (®s->madr, saddr << 1, 0);
> -
> - /* Enable module */
> - mpc_reg_out (®s->mcr, I2C_EN, I2C_INIT_MASK);
> - mpc_reg_out (®s->msr, 0, I2C_IF);
> - }
> -
> - /* Disable interrupts */
> - out_be32(&im->i2c.icr, 0);
> -
> - /* Turn off filters */
> - out_be32(&im->i2c.mifr, 0);
> -}
> -
> -static int mpc_get_fdr (int speed)
> -{
> - static int fdr = -1;
> -
> - if (fdr == -1) {
> - ulong best_speed = 0;
> - ulong divider;
> - ulong ips, scl;
> - ulong bestmatch = 0xffffffffUL;
> - int best_i = 0, best_j = 0, i, j;
> - int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8};
> - struct mpc512x_i2c_tap scltap[] = {
> - {4, 1},
> - {4, 2},
> - {6, 4},
> - {6, 8},
> - {14, 16},
> - {30, 32},
> - {62, 64},
> - {126, 128}
> - };
> -
> - ips = gd->arch.ips_clk;
> - for (i = 7; i >= 0; i--) {
> - for (j = 7; j >= 0; j--) {
> - scl = 2 * (scltap[j].scl2tap +
> - (SCL_Tap[i] - 1) * scltap[j].tap2tap
> - + 2);
> - if (ips <= speed*scl) {
> - if ((speed*scl - ips) < bestmatch) {
> - bestmatch = speed*scl - ips;
> - best_i = i;
> - best_j = j;
> - best_speed = ips/scl;
> - }
> - }
> - }
> - }
> - divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2);
> - if (gd->flags & GD_FLG_RELOC) {
> - fdr = divider;
> - } else {
> - debug("%ld kHz, \n", best_speed / 1000);
> - return divider;
> - }
> - }
> -
> - return fdr;
> -}
> -
> -int i2c_probe (uchar chip)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - int i;
> -
> - for (i = 0; i < I2C_RETRIES; i++) {
> - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
> -
> - if (! do_address (chip, 0)) {
> - mpc_reg_out (®s->mcr, 0, I2C_STA);
> - udelay (500);
> - break;
> - }
> -
> - mpc_reg_out (®s->mcr, 0, I2C_STA);
> - udelay (500);
> - }
> -
> - return (i == I2C_RETRIES);
> -}
> -
> -int i2c_read (uchar chip, uint addr, int alen, uchar *buf, int len)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - char xaddr[4];
> - int ret = -1;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> - if (wait_for_bb ()) {
> - printf ("i2c_read: bus is busy\n");
> - goto Done;
> - }
> -
> - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
> - if (do_address (chip, 0)) {
> - printf ("i2c_read: failed to address chip\n");
> - goto Done;
> - }
> -
> - if (send_bytes (chip, &xaddr[4-alen], alen)) {
> - printf ("i2c_read: send_bytes failed\n");
> - goto Done;
> - }
> -
> - mpc_reg_out (®s->mcr, I2C_RSTA, I2C_RSTA);
> - if (do_address (chip, 1)) {
> - printf ("i2c_read: failed to address chip\n");
> - goto Done;
> - }
> -
> - if (receive_bytes (chip, (char *)buf, len)) {
> - printf ("i2c_read: receive_bytes failed\n");
> - goto Done;
> - }
> -
> - ret = 0;
> -Done:
> - mpc_reg_out (®s->mcr, 0, I2C_STA);
> - return ret;
> -}
> -
> -int i2c_write (uchar chip, uint addr, int alen, uchar *buf, int len)
> -{
> - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
> - char xaddr[4];
> - int ret = -1;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> - if (wait_for_bb ()) {
> - printf ("i2c_write: bus is busy\n");
> - goto Done;
> - }
> -
> - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
> - if (do_address (chip, 0)) {
> - printf ("i2c_write: failed to address chip\n");
> - goto Done;
> - }
> -
> - if (send_bytes (chip, &xaddr[4-alen], alen)) {
> - printf ("i2c_write: send_bytes failed\n");
> - goto Done;
> - }
> -
> - if (send_bytes (chip, (char *)buf, len)) {
> - printf ("i2c_write: send_bytes failed\n");
> - goto Done;
> - }
> -
> - ret = 0;
> -Done:
> - mpc_reg_out (®s->mcr, 0, I2C_STA);
> - return ret;
> -}
> -
> -int i2c_set_bus_num (unsigned int bus)
> -{
> - if (bus >= I2C_BUS_CNT) {
> - return -1;
> - }
> - bus_num = bus;
> -
> - return 0;
> -}
> -
> -unsigned int i2c_get_bus_num (void)
> -{
> - return bus_num;
> -}
> -
> -#endif /* CONFIG_HARD_I2C */
> diff --git a/arch/powerpc/cpu/mpc5xxx/Makefile b/arch/powerpc/cpu/mpc5xxx/Makefile
> index 5c67e1d37d..88e3b2e3ae 100644
> --- a/arch/powerpc/cpu/mpc5xxx/Makefile
> +++ b/arch/powerpc/cpu/mpc5xxx/Makefile
> @@ -9,7 +9,6 @@ extra-y = start.o
> extra-y += traps.o
> obj-y += io.o
> obj-y += firmware_sc_task_bestcomm.impl.o
> -obj-y += i2c.o
> obj-y += cpu.o
> obj-y += cpu_init.o
> obj-y += ide.o
> diff --git a/arch/powerpc/cpu/mpc5xxx/i2c.c b/arch/powerpc/cpu/mpc5xxx/i2c.c
> deleted file mode 100644
> index 73601ae184..0000000000
> --- a/arch/powerpc/cpu/mpc5xxx/i2c.c
> +++ /dev/null
> @@ -1,456 +0,0 @@
> -/*
> - * (C) Copyright 2003
> - * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> - *
> - * SPDX-License-Identifier: GPL-2.0+
> - */
> -
> -#include <common.h>
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -#ifdef CONFIG_HARD_I2C
> -
> -#include <mpc5xxx.h>
> -#include <i2c.h>
> -
> -#if !defined(CONFIG_I2C_MULTI_BUS)
> -#if (CONFIG_SYS_I2C_MODULE == 2)
> -#define I2C_BASE MPC5XXX_I2C2
> -#elif (CONFIG_SYS_I2C_MODULE == 1)
> -#define I2C_BASE MPC5XXX_I2C1
> -#else
> -#error CONFIG_SYS_I2C_MODULE is not properly configured
> -#endif
> -#else
> -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) =
> - CONFIG_SYS_SPD_BUS_NUM;
> -static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED,
> - CONFIG_SYS_I2C_SPEED};
> -
> -static const unsigned long i2c_dev[2] = {
> - MPC5XXX_I2C1,
> - MPC5XXX_I2C2,
> -};
> -
> -#define I2C_BASE ((struct mpc5xxx_i2c *)i2c_dev[i2c_bus_num])
> -#endif
> -
> -#define I2C_TIMEOUT 6667
> -#define I2C_RETRIES 3
> -
> -struct mpc5xxx_i2c_tap {
> - int scl2tap;
> - int tap2tap;
> -};
> -
> -static int mpc_reg_in (volatile u32 *reg);
> -static void mpc_reg_out (volatile u32 *reg, int val, int mask);
> -static int wait_for_bb (void);
> -static int wait_for_pin (int *status);
> -static int do_address (uchar chip, char rdwr_flag);
> -static int send_bytes (uchar chip, char *buf, int len);
> -static int receive_bytes (uchar chip, char *buf, int len);
> -static int mpc_get_fdr (int);
> -
> -static int mpc_reg_in(volatile u32 *reg)
> -{
> - int ret = *reg >> 24;
> - __asm__ __volatile__ ("eieio");
> - return ret;
> -}
> -
> -static void mpc_reg_out(volatile u32 *reg, int val, int mask)
> -{
> - int tmp;
> -
> - if (!mask) {
> - *reg = val << 24;
> - } else {
> - tmp = mpc_reg_in(reg);
> - *reg = ((tmp & ~mask) | (val & mask)) << 24;
> - }
> - __asm__ __volatile__ ("eieio");
> -
> - return;
> -}
> -
> -static int wait_for_bb(void)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int timeout = I2C_TIMEOUT;
> - int status;
> -
> - status = mpc_reg_in(®s->msr);
> -
> - while (timeout-- && (status & I2C_BB)) {
> - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
> - (void)mpc_reg_in(®s->mdr);
> - mpc_reg_out(®s->mcr, 0, I2C_STA);
> - mpc_reg_out(®s->mcr, 0, 0);
> - mpc_reg_out(®s->mcr, I2C_EN, 0);
> - udelay(15);
> - status = mpc_reg_in(®s->msr);
> - }
> -
> - return (status & I2C_BB);
> -}
> -
> -static int wait_for_pin(int *status)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int timeout = I2C_TIMEOUT;
> -
> - *status = mpc_reg_in(®s->msr);
> -
> - while (timeout-- && !(*status & I2C_IF)) {
> - udelay(15);
> - *status = mpc_reg_in(®s->msr);
> - }
> -
> - if (!(*status & I2C_IF)) {
> - return -1;
> - }
> -
> - mpc_reg_out(®s->msr, 0, I2C_IF);
> -
> - return 0;
> -}
> -
> -static int do_address(uchar chip, char rdwr_flag)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int status;
> -
> - chip <<= 1;
> -
> - if (rdwr_flag) {
> - chip |= 1;
> - }
> -
> - mpc_reg_out(®s->mcr, I2C_TX, I2C_TX);
> - mpc_reg_out(®s->mdr, chip, 0);
> -
> - if (wait_for_pin(&status)) {
> - return -2;
> - }
> -
> - if (status & I2C_RXAK) {
> - return -3;
> - }
> -
> - return 0;
> -}
> -
> -static int send_bytes(uchar chip, char *buf, int len)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int wrcount;
> - int status;
> -
> - for (wrcount = 0; wrcount < len; ++wrcount) {
> -
> - mpc_reg_out(®s->mdr, buf[wrcount], 0);
> -
> - if (wait_for_pin(&status)) {
> - break;
> - }
> -
> - if (status & I2C_RXAK) {
> - break;
> - }
> -
> - }
> -
> - return !(wrcount == len);
> -}
> -
> -static int receive_bytes(uchar chip, char *buf, int len)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int dummy = 1;
> - int rdcount = 0;
> - int status;
> - int i;
> -
> - mpc_reg_out(®s->mcr, 0, I2C_TX);
> -
> - for (i = 0; i < len; ++i) {
> - buf[rdcount] = mpc_reg_in(®s->mdr);
> -
> - if (dummy) {
> - dummy = 0;
> - } else {
> - rdcount++;
> - }
> -
> -
> - if (wait_for_pin(&status)) {
> - return -4;
> - }
> - }
> -
> - mpc_reg_out(®s->mcr, I2C_TXAK, I2C_TXAK);
> - buf[rdcount++] = mpc_reg_in(®s->mdr);
> -
> - if (wait_for_pin(&status)) {
> - return -5;
> - }
> -
> - mpc_reg_out(®s->mcr, 0, I2C_TXAK);
> -
> - return 0;
> -}
> -
> -#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
> -
> -#define FDR510(x) (u8) (((x & 0x20) >> 3) | (x & 0x3))
> -#define FDR432(x) (u8) ((x & 0x1C) >> 2)
> -/*
> - * Reset any i2c devices that may have been interrupted during a system reset.
> - * Normally this would be accomplished by clocking the line until SCL and SDA
> - * are released and then sending a start condtiion (From an Atmel datasheet).
> - * There is no direct access to the i2c pins so instead create start commands
> - * through the i2c interface. Send a start command then delay for the SDA Hold
> - * time, repeat this by disabling/enabling the bus a total of 9 times.
> - */
> -static void send_reset(void)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int i;
> - u32 delay;
> - u8 fdr;
> - int SDA_Tap[] = { 3, 3, 4, 4, 1, 1, 2, 2};
> - struct mpc5xxx_i2c_tap scltap[] = {
> - {4, 1},
> - {4, 2},
> - {6, 4},
> - {6, 8},
> - {14, 16},
> - {30, 32},
> - {62, 64},
> - {126, 128}
> - };
> -
> - fdr = (u8)mpc_reg_in(®s->mfdr);
> -
> - delay = scltap[FDR432(fdr)].scl2tap + ((SDA_Tap[FDR510(fdr)] - 1) * \
> - scltap[FDR432(fdr)].tap2tap) + 3;
> -
> - for (i = 0; i < 9; i++) {
> - mpc_reg_out(®s->mcr, I2C_EN|I2C_STA|I2C_TX, I2C_INIT_MASK);
> - udelay(delay);
> - mpc_reg_out(®s->mcr, 0, I2C_INIT_MASK);
> - udelay(delay);
> - }
> -
> - mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK);
> -}
> -#endif /* CONFIG_SYS_I2c_INIT_MPC5XXX */
> -
> -/**************** I2C API ****************/
> -
> -void i2c_init(int speed, int saddr)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> -
> - mpc_reg_out(®s->mcr, 0, 0);
> - mpc_reg_out(®s->madr, saddr << 1, 0);
> -
> - /* Set clock
> - */
> - mpc_reg_out(®s->mfdr, mpc_get_fdr(speed), 0);
> -
> - /* Enable module
> - */
> - mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK);
> - mpc_reg_out(®s->msr, 0, I2C_IF);
> -
> -#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
> - send_reset();
> -#endif
> - return;
> -}
> -
> -static int mpc_get_fdr(int speed)
> -{
> - static int fdr = -1;
> -
> - if (fdr == -1) {
> - ulong best_speed = 0;
> - ulong divider;
> - ulong ipb, scl;
> - ulong bestmatch = 0xffffffffUL;
> - int best_i = 0, best_j = 0, i, j;
> - int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8};
> - struct mpc5xxx_i2c_tap scltap[] = {
> - {4, 1},
> - {4, 2},
> - {6, 4},
> - {6, 8},
> - {14, 16},
> - {30, 32},
> - {62, 64},
> - {126, 128}
> - };
> -
> - ipb = gd->arch.ipb_clk;
> - for (i = 7; i >= 0; i--) {
> - for (j = 7; j >= 0; j--) {
> - scl = 2 * (scltap[j].scl2tap +
> - (SCL_Tap[i] - 1) * scltap[j].tap2tap + 2);
> - if (ipb <= speed*scl) {
> - if ((speed*scl - ipb) < bestmatch) {
> - bestmatch = speed*scl - ipb;
> - best_i = i;
> - best_j = j;
> - best_speed = ipb/scl;
> - }
> - }
> - }
> - }
> - divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2);
> - if (gd->flags & GD_FLG_RELOC) {
> - fdr = divider;
> - } else {
> - printf("%ld kHz, ", best_speed / 1000);
> - return divider;
> - }
> - }
> -
> - return fdr;
> -}
> -
> -int i2c_probe(uchar chip)
> -{
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int i;
> -
> - for (i = 0; i < I2C_RETRIES; i++) {
> - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
> -
> - if (! do_address(chip, 0)) {
> - mpc_reg_out(®s->mcr, 0, I2C_STA);
> - udelay(500);
> - break;
> - }
> -
> - mpc_reg_out(®s->mcr, 0, I2C_STA);
> - udelay(500);
> - }
> -
> - return (i == I2C_RETRIES);
> -}
> -
> -int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len)
> -{
> - char xaddr[4];
> - struct mpc5xxx_i2c * regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int ret = -1;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> - if (wait_for_bb()) {
> - printf("i2c_read: bus is busy\n");
> - goto Done;
> - }
> -
> - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
> - if (do_address(chip, 0)) {
> - printf("i2c_read: failed to address chip\n");
> - goto Done;
> - }
> -
> - if (send_bytes(chip, &xaddr[4-alen], alen)) {
> - printf("i2c_read: send_bytes failed\n");
> - goto Done;
> - }
> -
> - mpc_reg_out(®s->mcr, I2C_RSTA, I2C_RSTA);
> - if (do_address(chip, 1)) {
> - printf("i2c_read: failed to address chip\n");
> - goto Done;
> - }
> -
> - if (receive_bytes(chip, (char *)buf, len)) {
> - printf("i2c_read: receive_bytes failed\n");
> - goto Done;
> - }
> -
> - ret = 0;
> -Done:
> - mpc_reg_out(®s->mcr, 0, I2C_STA);
> - return ret;
> -}
> -
> -int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len)
> -{
> - char xaddr[4];
> - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
> - int ret = -1;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> - if (wait_for_bb()) {
> - printf("i2c_write: bus is busy\n");
> - goto Done;
> - }
> -
> - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
> - if (do_address(chip, 0)) {
> - printf("i2c_write: failed to address chip\n");
> - goto Done;
> - }
> -
> - if (send_bytes(chip, &xaddr[4-alen], alen)) {
> - printf("i2c_write: send_bytes failed\n");
> - goto Done;
> - }
> -
> - if (send_bytes(chip, (char *)buf, len)) {
> - printf("i2c_write: send_bytes failed\n");
> - goto Done;
> - }
> -
> - ret = 0;
> -Done:
> - mpc_reg_out(®s->mcr, 0, I2C_STA);
> - return ret;
> -}
> -
> -#if defined(CONFIG_I2C_MULTI_BUS)
> -int i2c_set_bus_num(unsigned int bus)
> -{
> - if (bus > 1)
> - return -1;
> -
> - i2c_bus_num = bus;
> - i2c_init(i2c_bus_speed[bus], CONFIG_SYS_I2C_SLAVE);
> - return 0;
> -}
> -
> -int i2c_set_bus_speed(unsigned int speed)
> -{
> - i2c_init(speed, CONFIG_SYS_I2C_SLAVE);
> - return 0;
> -}
> -
> -unsigned int i2c_get_bus_num(void)
> -{
> - return i2c_bus_num;
> -}
> -
> -unsigned int i2c_get_bus_speed(void)
> -{
> - return i2c_bus_speed[i2c_bus_num];
> -}
> -#endif
> -
> -
> -#endif /* CONFIG_HARD_I2C */
> diff --git a/arch/powerpc/cpu/mpc8260/Makefile b/arch/powerpc/cpu/mpc8260/Makefile
> index 83adc4c436..72dd8aba25 100644
> --- a/arch/powerpc/cpu/mpc8260/Makefile
> +++ b/arch/powerpc/cpu/mpc8260/Makefile
> @@ -7,7 +7,7 @@
>
> extra-y = start.o
> obj-y = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
> - interrupts.o ether_fcc.o i2c.o commproc.o \
> + interrupts.o ether_fcc.o commproc.o \
> bedbug_603e.o pci.o spi.o kgdb.o
>
> obj-$(CONFIG_ETHER_ON_SCC) += ether_scc.o
> diff --git a/arch/powerpc/cpu/mpc8260/commproc.c b/arch/powerpc/cpu/mpc8260/commproc.c
> index 484bd17745..ff69881089 100644
> --- a/arch/powerpc/cpu/mpc8260/commproc.c
> +++ b/arch/powerpc/cpu/mpc8260/commproc.c
> @@ -41,10 +41,6 @@ m8260_cpm_reset(void)
> do { /* Spin until command processed */
> __asm__ __volatile__ ("eieio");
> } while ((immr->im_cpm.cp_cpcr & CPM_CR_FLG) && ++count < 1000000);
> -
> -#ifdef CONFIG_HARD_I2C
> - immr->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = 0;
> -#endif
> }
>
> /* Allocate some memory from the dual ported ram.
> diff --git a/arch/powerpc/cpu/mpc8260/i2c.c b/arch/powerpc/cpu/mpc8260/i2c.c
> deleted file mode 100644
> index a0de101329..0000000000
> --- a/arch/powerpc/cpu/mpc8260/i2c.c
> +++ /dev/null
> @@ -1,741 +0,0 @@
> -/*
> - * (C) Copyright 2000
> - * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio at tin.it
> - *
> - * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
> - * Marius Groeger <mgroeger@sysgo.de>
> - *
> - * SPDX-License-Identifier: GPL-2.0+
> - */
> -
> -#include <common.h>
> -#include <console.h>
> -
> -#if defined(CONFIG_HARD_I2C)
> -
> -#include <asm/cpm_8260.h>
> -#include <i2c.h>
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -#if defined(CONFIG_I2C_MULTI_BUS)
> -static unsigned int i2c_bus_num __attribute__ ((section(".data"))) = 0;
> -#endif /* CONFIG_I2C_MULTI_BUS */
> -
> -/* uSec to wait between polls of the i2c */
> -#define DELAY_US 100
> -/* uSec to wait for the CPM to start processing the buffer */
> -#define START_DELAY_US 1000
> -
> -/*
> - * tx/rx per-byte timeout: we delay DELAY_US uSec between polls so the
> - * timeout will be (tx_length + rx_length) * DELAY_US * TOUT_LOOP
> - */
> -#define TOUT_LOOP 5
> -
> -/*
> - * Set default values
> - */
> -#ifndef CONFIG_SYS_I2C_SPEED
> -#define CONFIG_SYS_I2C_SPEED 50000
> -#endif
> -
> -
> -typedef void (*i2c_ecb_t) (int, int, void *); /* error callback function */
> -
> -/* This structure keeps track of the bd and buffer space usage. */
> -typedef struct i2c_state {
> - int rx_idx; /* index to next free Rx BD */
> - int tx_idx; /* index to next free Tx BD */
> - void *rxbd; /* pointer to next free Rx BD */
> - void *txbd; /* pointer to next free Tx BD */
> - int tx_space; /* number of Tx bytes left */
> - unsigned char *tx_buf; /* pointer to free Tx area */
> - i2c_ecb_t err_cb; /* error callback function */
> - void *cb_data; /* private data to be passed */
> -} i2c_state_t;
> -
> -/* flags for i2c_send() and i2c_receive() */
> -#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */
> -#define I2CF_START_COND 0x02 /* tx: generate start condition */
> -#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */
> -
> -/* return codes */
> -#define I2CERR_NO_BUFFERS 1 /* no more BDs or buffer space */
> -#define I2CERR_MSG_TOO_LONG 2 /* tried to send/receive to much data */
> -#define I2CERR_TIMEOUT 3 /* timeout in i2c_doio() */
> -#define I2CERR_QUEUE_EMPTY 4 /* i2c_doio called without send/rcv */
> -#define I2CERR_IO_ERROR 5 /* had an error during comms */
> -
> -/* error callback flags */
> -#define I2CECB_RX_ERR 0x10 /* this is a receive error */
> -#define I2CECB_RX_OV 0x02 /* receive overrun error */
> -#define I2CECB_RX_MASK 0x0f /* mask for error bits */
> -#define I2CECB_TX_ERR 0x20 /* this is a transmit error */
> -#define I2CECB_TX_CL 0x01 /* transmit collision error */
> -#define I2CECB_TX_UN 0x02 /* transmit underflow error */
> -#define I2CECB_TX_NAK 0x04 /* transmit no ack error */
> -#define I2CECB_TX_MASK 0x0f /* mask for error bits */
> -#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */
> -
> -#define ERROR_I2C_NONE 0
> -#define ERROR_I2C_LENGTH 1
> -
> -#define I2C_WRITE_BIT 0x00
> -#define I2C_READ_BIT 0x01
> -
> -#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
> -
> -
> -#define NUM_RX_BDS 4
> -#define NUM_TX_BDS 4
> -#define MAX_TX_SPACE 256
> -
> -typedef struct I2C_BD {
> - unsigned short status;
> - unsigned short length;
> - unsigned char *addr;
> -} I2C_BD;
> -
> -#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */
> -
> -#define BD_I2C_TX_CL 0x0001 /* collision error */
> -#define BD_I2C_TX_UN 0x0002 /* underflow error */
> -#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */
> -#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL)
> -
> -#define BD_I2C_RX_ERR BD_SC_OV
> -
> -/*
> - * Returns the best value of I2BRG to meet desired clock speed of I2C with
> - * input parameters (clock speed, filter, and predivider value).
> - * It returns computer speed value and the difference between it and desired
> - * speed.
> - */
> -static inline int
> -i2c_roundrate(int hz, int speed, int filter, int modval,
> - int *brgval, int *totspeed)
> -{
> - int moddiv = 1 << (5 - (modval & 3)), brgdiv, div;
> -
> - debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n",
> - hz, speed, filter, modval);
> -
> - div = moddiv * speed;
> - brgdiv = (hz + div - 1) / div;
> -
> - debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv);
> -
> - *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter);
> -
> - if ((*brgval < 0) || (*brgval > 255)) {
> - debug("\t\trejected brgval=%d\n", *brgval);
> - return -1;
> - }
> -
> - brgdiv = 2 * (*brgval + 3 + (2 * filter));
> - div = moddiv * brgdiv;
> - *totspeed = hz / div;
> -
> - debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed);
> -
> - return 0;
> -}
> -
> -/*
> - * Sets the I2C clock predivider and divider to meet required clock speed.
> - */
> -static int i2c_setrate(int hz, int speed)
> -{
> - immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
> - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
> - int brgval,
> - modval, /* 0-3 */
> - bestspeed_diff = speed,
> - bestspeed_brgval = 0,
> - bestspeed_modval = 0,
> - bestspeed_filter = 0,
> - totspeed,
> - filter = 0; /* Use this fixed value */
> -
> - for (modval = 0; modval < 4; modval++) {
> - if (i2c_roundrate(hz, speed, filter, modval, &brgval, &totspeed)
> - == 0) {
> - int diff = speed - totspeed;
> -
> - if ((diff >= 0) && (diff < bestspeed_diff)) {
> - bestspeed_diff = diff;
> - bestspeed_modval = modval;
> - bestspeed_brgval = brgval;
> - bestspeed_filter = filter;
> - }
> - }
> - }
> -
> - debug("[I2C] Best is:\n");
> - debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n",
> - hz, speed, bestspeed_filter, bestspeed_modval, bestspeed_brgval,
> - bestspeed_diff);
> -
> - i2c->i2c_i2mod |= ((bestspeed_modval & 3) << 1) |
> - (bestspeed_filter << 3);
> - i2c->i2c_i2brg = bestspeed_brgval & 0xff;
> -
> - debug("[I2C] i2mod=%08x i2brg=%08x\n", i2c->i2c_i2mod,
> - i2c->i2c_i2brg);
> -
> - return 1;
> -}
> -
> -void i2c_init(int speed, int slaveadd)
> -{
> - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
> - volatile cpm8260_t *cp = (cpm8260_t *)&immap->im_cpm;
> - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
> - volatile iic_t *iip;
> - ulong rbase, tbase;
> - volatile I2C_BD *rxbd, *txbd;
> - uint dpaddr;
> -
> -#ifdef CONFIG_SYS_I2C_INIT_BOARD
> - /*
> - * call board specific i2c bus reset routine before accessing the
> - * environment, which might be in a chip on that bus. For details
> - * about this problem see doc/I2C_Edge_Conditions.
> - */
> - i2c_init_board();
> -#endif
> -
> - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
> - if (dpaddr == 0) {
> - /* need to allocate dual port ram */
> - dpaddr = m8260_cpm_dpalloc(64 +
> - (NUM_RX_BDS * sizeof(I2C_BD)) +
> - (NUM_TX_BDS * sizeof(I2C_BD)) +
> - MAX_TX_SPACE, 64);
> - immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] =
> - dpaddr;
> - }
> -
> - /*
> - * initialise data in dual port ram:
> - *
> - * dpaddr -> parameter ram (64 bytes)
> - * rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes)
> - * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes)
> - * tx buffer (MAX_TX_SPACE bytes)
> - */
> -
> - iip = (iic_t *)&immap->im_dprambase[dpaddr];
> - memset((void *)iip, 0, sizeof(iic_t));
> -
> - rbase = dpaddr + 64;
> - tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD);
> -
> - /* Disable interrupts */
> - i2c->i2c_i2mod = 0x00;
> - i2c->i2c_i2cmr = 0x00;
> - i2c->i2c_i2cer = 0xff;
> - i2c->i2c_i2add = slaveadd;
> -
> - /*
> - * Set the I2C BRG Clock division factor from desired i2c rate
> - * and current CPU rate (we assume sccr dfbgr field is 0;
> - * divide BRGCLK by 1)
> - */
> - debug("[I2C] Setting rate...\n");
> - i2c_setrate(gd->arch.brg_clk, CONFIG_SYS_I2C_SPEED);
> -
> - /* Set I2C controller in master mode */
> - i2c->i2c_i2com = 0x01;
> -
> - /* Initialize Tx/Rx parameters */
> - iip->iic_rbase = rbase;
> - iip->iic_tbase = tbase;
> - rxbd = (I2C_BD *)((unsigned char *) &immap->
> - im_dprambase[iip->iic_rbase]);
> - txbd = (I2C_BD *)((unsigned char *) &immap->
> - im_dprambase[iip->iic_tbase]);
> -
> - debug("[I2C] rbase = %04x\n", iip->iic_rbase);
> - debug("[I2C] tbase = %04x\n", iip->iic_tbase);
> - debug("[I2C] rxbd = %08x\n", (int) rxbd);
> - debug("[I2C] txbd = %08x\n", (int) txbd);
> -
> - /* Set big endian byte order */
> - iip->iic_tfcr = 0x10;
> - iip->iic_rfcr = 0x10;
> -
> - /* Set maximum receive size. */
> - iip->iic_mrblr = I2C_RXTX_LEN;
> -
> - cp->cp_cpcr = mk_cr_cmd(CPM_CR_I2C_PAGE,
> - CPM_CR_I2C_SBLOCK,
> - 0x00, CPM_CR_INIT_TRX) | CPM_CR_FLG;
> - do {
> - __asm__ __volatile__("eieio");
> - } while (cp->cp_cpcr & CPM_CR_FLG);
> -
> - /* Clear events and interrupts */
> - i2c->i2c_i2cer = 0xff;
> - i2c->i2c_i2cmr = 0x00;
> -}
> -
> -static
> -void i2c_newio(i2c_state_t *state)
> -{
> - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
> - volatile iic_t *iip;
> - uint dpaddr;
> -
> - debug("[I2C] i2c_newio\n");
> -
> - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
> - iip = (iic_t *)&immap->im_dprambase[dpaddr];
> - state->rx_idx = 0;
> - state->tx_idx = 0;
> - state->rxbd = (void *)&immap->im_dprambase[iip->iic_rbase];
> - state->txbd = (void *)&immap->im_dprambase[iip->iic_tbase];
> - state->tx_space = MAX_TX_SPACE;
> - state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD);
> - state->err_cb = NULL;
> - state->cb_data = NULL;
> -
> - debug("[I2C] rxbd = %08x\n", (int)state->rxbd);
> - debug("[I2C] txbd = %08x\n", (int)state->txbd);
> - debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf);
> -
> - /* clear the buffer memory */
> - memset((char *) state->tx_buf, 0, MAX_TX_SPACE);
> -}
> -
> -static
> -int i2c_send(i2c_state_t *state,
> - unsigned char address,
> - unsigned char secondary_address,
> - unsigned int flags, unsigned short size, unsigned char *dataout)
> -{
> - volatile I2C_BD *txbd;
> - int i, j;
> -
> - debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n",
> - address, secondary_address, flags, size);
> -
> - /* trying to send message larger than BD */
> - if (size > I2C_RXTX_LEN)
> - return I2CERR_MSG_TOO_LONG;
> -
> - /* no more free bds */
> - if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size))
> - return I2CERR_NO_BUFFERS;
> -
> - txbd = (I2C_BD *)state->txbd;
> - txbd->addr = state->tx_buf;
> -
> - debug("[I2C] txbd = %08x\n", (int) txbd);
> -
> - if (flags & I2CF_START_COND) {
> - debug("[I2C] Formatting addresses...\n");
> - if (flags & I2CF_ENABLE_SECONDARY) {
> - /* Length of message plus dest addresses */
> - txbd->length = size + 2;
> - txbd->addr[0] = address << 1;
> - txbd->addr[1] = secondary_address;
> - i = 2;
> - } else {
> - /* Length of message plus dest address */
> - txbd->length = size + 1;
> - /* Write destination address to BD */
> - txbd->addr[0] = address << 1;
> - i = 1;
> - }
> - } else {
> - txbd->length = size; /* Length of message */
> - i = 0;
> - }
> -
> - /* set up txbd */
> - txbd->status = BD_SC_READY;
> - if (flags & I2CF_START_COND)
> - txbd->status |= BD_I2C_TX_START;
> - if (flags & I2CF_STOP_COND)
> - txbd->status |= BD_SC_LAST | BD_SC_WRAP;
> -
> - /* Copy data to send into buffer */
> - debug("[I2C] copy data...\n");
> - for (j = 0; j < size; i++, j++)
> - txbd->addr[i] = dataout[j];
> -
> - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
> - txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]);
> -
> - /* advance state */
> - state->tx_buf += txbd->length;
> - state->tx_space -= txbd->length;
> - state->tx_idx++;
> - state->txbd = (void *) (txbd + 1);
> -
> - return 0;
> -}
> -
> -static
> -int i2c_receive(i2c_state_t *state,
> - unsigned char address,
> - unsigned char secondary_address,
> - unsigned int flags,
> - unsigned short size_to_expect, unsigned char *datain)
> -{
> - volatile I2C_BD *rxbd, *txbd;
> -
> - debug("[I2C] i2c_receive %02d %02d %02d\n", address,
> - secondary_address, flags);
> -
> - /* Expected to receive too much */
> - if (size_to_expect > I2C_RXTX_LEN)
> - return I2CERR_MSG_TOO_LONG;
> -
> - /* no more free bds */
> - if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS
> - || state->tx_space < 2)
> - return I2CERR_NO_BUFFERS;
> -
> - rxbd = (I2C_BD *) state->rxbd;
> - txbd = (I2C_BD *) state->txbd;
> -
> - debug("[I2C] rxbd = %08x\n", (int) rxbd);
> - debug("[I2C] txbd = %08x\n", (int) txbd);
> -
> - txbd->addr = state->tx_buf;
> -
> - /* set up TXBD for destination address */
> - if (flags & I2CF_ENABLE_SECONDARY) {
> - txbd->length = 2;
> - txbd->addr[0] = address << 1; /* Write data */
> - txbd->addr[1] = secondary_address; /* Internal address */
> - txbd->status = BD_SC_READY;
> - } else {
> - txbd->length = 1 + size_to_expect;
> - txbd->addr[0] = (address << 1) | 0x01;
> - txbd->status = BD_SC_READY;
> - memset(&txbd->addr[1], 0, txbd->length);
> - }
> -
> - /* set up rxbd for reception */
> - rxbd->status = BD_SC_EMPTY;
> - rxbd->length = size_to_expect;
> - rxbd->addr = datain;
> -
> - txbd->status |= BD_I2C_TX_START;
> - if (flags & I2CF_STOP_COND) {
> - txbd->status |= BD_SC_LAST | BD_SC_WRAP;
> - rxbd->status |= BD_SC_WRAP;
> - }
> -
> - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
> - txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]);
> - debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
> - rxbd->length, rxbd->status, rxbd->addr[0], rxbd->addr[1]);
> -
> - /* advance state */
> - state->tx_buf += txbd->length;
> - state->tx_space -= txbd->length;
> - state->tx_idx++;
> - state->txbd = (void *) (txbd + 1);
> - state->rx_idx++;
> - state->rxbd = (void *) (rxbd + 1);
> -
> - return 0;
> -}
> -
> -
> -static
> -int i2c_doio(i2c_state_t *state)
> -{
> - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
> - volatile iic_t *iip;
> - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
> - volatile I2C_BD *txbd, *rxbd;
> - int n, i, b, rxcnt = 0, rxtimeo = 0, txcnt = 0, txtimeo = 0, rc = 0;
> - uint dpaddr;
> -
> - debug("[I2C] i2c_doio\n");
> -
> - if (state->tx_idx <= 0 && state->rx_idx <= 0) {
> - debug("[I2C] No I/O is queued\n");
> - return I2CERR_QUEUE_EMPTY;
> - }
> -
> - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
> - iip = (iic_t *)&immap->im_dprambase[dpaddr];
> - iip->iic_rbptr = iip->iic_rbase;
> - iip->iic_tbptr = iip->iic_tbase;
> -
> - /* Enable I2C */
> - debug("[I2C] Enabling I2C...\n");
> - i2c->i2c_i2mod |= 0x01;
> -
> - /* Begin transmission */
> - i2c->i2c_i2com |= 0x80;
> -
> - /* Loop until transmit & receive completed */
> -
> - n = state->tx_idx;
> -
> - if (n > 0) {
> -
> - txbd = ((I2C_BD *) state->txbd) - n;
> - for (i = 0; i < n; i++) {
> - txtimeo += TOUT_LOOP * txbd->length;
> - txbd++;
> - }
> -
> - txbd--; /* wait until last in list is done */
> -
> - debug("[I2C] Transmitting...(txbd=0x%08lx)\n",
> - (ulong) txbd);
> -
> - udelay(START_DELAY_US); /* give it time to start */
> - while ((txbd->status & BD_SC_READY) && (++txcnt < txtimeo)) {
> - udelay(DELAY_US);
> - if (ctrlc())
> - return -1;
> - __asm__ __volatile__("eieio");
> - }
> - }
> -
> - n = state->rx_idx;
> -
> - if (txcnt < txtimeo && n > 0) {
> -
> - rxbd = ((I2C_BD *) state->rxbd) - n;
> - for (i = 0; i < n; i++) {
> - rxtimeo += TOUT_LOOP * rxbd->length;
> - rxbd++;
> - }
> -
> - rxbd--; /* wait until last in list is done */
> -
> - debug("[I2C] Receiving...(rxbd=0x%08lx)\n", (ulong) rxbd);
> -
> - udelay(START_DELAY_US); /* give it time to start */
> - while ((rxbd->status & BD_SC_EMPTY) && (++rxcnt < rxtimeo)) {
> - udelay(DELAY_US);
> - if (ctrlc())
> - return -1;
> - __asm__ __volatile__("eieio");
> - }
> - }
> -
> - /* Turn off I2C */
> - i2c->i2c_i2mod &= ~0x01;
> -
> - n = state->tx_idx;
> -
> - if (n > 0) {
> - for (i = 0; i < n; i++) {
> - txbd = ((I2C_BD *) state->txbd) - (n - i);
> - b = txbd->status & BD_I2C_TX_ERR;
> - if (b != 0) {
> - if (state->err_cb != NULL)
> - (*state->err_cb) (I2CECB_TX_ERR | b,
> - i, state->cb_data);
> - if (rc == 0)
> - rc = I2CERR_IO_ERROR;
> - }
> - }
> - }
> -
> - n = state->rx_idx;
> -
> - if (n > 0) {
> - for (i = 0; i < n; i++) {
> - rxbd = ((I2C_BD *) state->rxbd) - (n - i);
> - b = rxbd->status & BD_I2C_RX_ERR;
> - if (b != 0) {
> - if (state->err_cb != NULL)
> - (*state->err_cb) (I2CECB_RX_ERR | b,
> - i, state->cb_data);
> - if (rc == 0)
> - rc = I2CERR_IO_ERROR;
> - }
> - }
> - }
> -
> - if ((txtimeo > 0 && txcnt >= txtimeo) ||
> - (rxtimeo > 0 && rxcnt >= rxtimeo)) {
> - if (state->err_cb != NULL)
> - (*state->err_cb) (I2CECB_TIMEOUT, -1, state->cb_data);
> - if (rc == 0)
> - rc = I2CERR_TIMEOUT;
> - }
> -
> - return rc;
> -}
> -
> -static void i2c_probe_callback(int flags, int xnum, void *data)
> -{
> - /*
> - * the only acceptable errors are a transmit NAK or a receive
> - * overrun - tx NAK means the device does not exist, rx OV
> - * means the device must have responded to the slave address
> - * even though the transfer failed
> - */
> - if (flags == (I2CECB_TX_ERR | I2CECB_TX_NAK))
> - *(int *) data |= 1;
> - if (flags == (I2CECB_RX_ERR | I2CECB_RX_OV))
> - *(int *) data |= 2;
> -}
> -
> -int i2c_probe(uchar chip)
> -{
> - i2c_state_t state;
> - int rc, err_flag;
> - uchar buf[1];
> -
> - i2c_newio(&state);
> -
> - state.err_cb = i2c_probe_callback;
> - state.cb_data = (void *) &err_flag;
> - err_flag = 0;
> -
> - rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1,
> - buf);
> -
> - if (rc != 0)
> - return rc; /* probe failed */
> -
> - rc = i2c_doio(&state);
> -
> - if (rc == 0)
> - return 0; /* device exists - read succeeded */
> -
> - if (rc == I2CERR_TIMEOUT)
> - return -1; /* device does not exist - timeout */
> -
> - if (rc != I2CERR_IO_ERROR || err_flag == 0)
> - return rc; /* probe failed */
> -
> - if (err_flag & 1)
> - return -1; /* device does not exist - had transmit NAK */
> -
> - return 0; /* device exists - had receive overrun */
> -}
> -
> -
> -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> -{
> - i2c_state_t state;
> - uchar xaddr[4];
> - int rc;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
> - /*
> - * EEPROM chips that implement "address overflow" are ones
> - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address
> - * and the extra bits end up in the "chip address" bit slots.
> - * This makes a 24WC08 (1Kbyte) chip look like four 256 byte
> - * chips.
> - *
> - * Note that we consider the length of the address field to still
> - * be one byte because the extra address bits are hidden in the
> - * chip address.
> - */
> - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> -#endif
> -
> - i2c_newio(&state);
> -
> - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
> - &xaddr[4 - alen]);
> - if (rc != 0) {
> - printf("i2c_read: i2c_send failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer);
> - if (rc != 0) {
> - printf("i2c_read: i2c_receive failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_doio(&state);
> - if (rc != 0) {
> - printf("i2c_read: i2c_doio failed (%d)\n", rc);
> - return 1;
> - }
> - return 0;
> -}
> -
> -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> -{
> - i2c_state_t state;
> - uchar xaddr[4];
> - int rc;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
> - /*
> - * EEPROM chips that implement "address overflow" are ones
> - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address
> - * and the extra bits end up in the "chip address" bit slots.
> - * This makes a 24WC08 (1Kbyte) chip look like four 256 byte
> - * chips.
> - *
> - * Note that we consider the length of the address field to still
> - * be one byte because the extra address bits are hidden in the
> - * chip address.
> - */
> - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> -#endif
> -
> - i2c_newio(&state);
> -
> - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
> - &xaddr[4 - alen]);
> - if (rc != 0) {
> - printf("i2c_write: first i2c_send failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer);
> - if (rc != 0) {
> - printf("i2c_write: second i2c_send failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_doio(&state);
> - if (rc != 0) {
> - printf("i2c_write: i2c_doio failed (%d)\n", rc);
> - return 1;
> - }
> - return 0;
> -}
> -
> -#if defined(CONFIG_I2C_MULTI_BUS)
> -/*
> - * Functions for multiple I2C bus handling
> - */
> -unsigned int i2c_get_bus_num(void)
> -{
> - return i2c_bus_num;
> -}
> -
> -int i2c_set_bus_num(unsigned int bus)
> -{
> - if (bus >= CONFIG_SYS_MAX_I2C_BUS)
> - return -1;
> - i2c_bus_num = bus;
> - return 0;
> -}
> -
> -#endif /* CONFIG_I2C_MULTI_BUS */
> -#endif /* CONFIG_HARD_I2C */
> diff --git a/arch/powerpc/cpu/mpc8xx/Makefile b/arch/powerpc/cpu/mpc8xx/Makefile
> index 6f81fee571..fc91a054f0 100644
> --- a/arch/powerpc/cpu/mpc8xx/Makefile
> +++ b/arch/powerpc/cpu/mpc8xx/Makefile
> @@ -14,7 +14,6 @@ obj-y += cpu.o
> obj-y += cpu_init.o
> obj-y += fec.o
> obj-$(CONFIG_OF_LIBFDT) += fdt.o
> -obj-y += i2c.o
> obj-y += interrupts.o
> obj-y += scc.o
> obj-y += serial.o
> diff --git a/arch/powerpc/cpu/mpc8xx/i2c.c b/arch/powerpc/cpu/mpc8xx/i2c.c
> deleted file mode 100644
> index 54d5cb5130..0000000000
> --- a/arch/powerpc/cpu/mpc8xx/i2c.c
> +++ /dev/null
> @@ -1,672 +0,0 @@
> -/*
> - * (C) Copyright 2000
> - * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio at tin.it
> - *
> - * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
> - * Marius Groeger <mgroeger@sysgo.de>
> - *
> - * SPDX-License-Identifier: GPL-2.0+
> - *
> - * Back ported to the 8xx platform (from the 8260 platform) by
> - * Murray.Jensen at cmst.csiro.au, 27-Jan-01.
> - */
> -
> -#include <common.h>
> -#include <console.h>
> -
> -#ifdef CONFIG_HARD_I2C
> -
> -#include <commproc.h>
> -#include <i2c.h>
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -/* tx/rx timeout (we need the i2c early, so we don't use get_timer()) */
> -#define TOUT_LOOP 1000000
> -
> -#define NUM_RX_BDS 4
> -#define NUM_TX_BDS 4
> -#define MAX_TX_SPACE 256
> -#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
> -
> -typedef struct I2C_BD {
> - unsigned short status;
> - unsigned short length;
> - unsigned char *addr;
> -} I2C_BD;
> -
> -#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */
> -
> -#define BD_I2C_TX_CL 0x0001 /* collision error */
> -#define BD_I2C_TX_UN 0x0002 /* underflow error */
> -#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */
> -#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL)
> -
> -#define BD_I2C_RX_ERR BD_SC_OV
> -
> -typedef void (*i2c_ecb_t) (int, int); /* error callback function */
> -
> -/* This structure keeps track of the bd and buffer space usage. */
> -typedef struct i2c_state {
> - int rx_idx; /* index to next free Rx BD */
> - int tx_idx; /* index to next free Tx BD */
> - void *rxbd; /* pointer to next free Rx BD */
> - void *txbd; /* pointer to next free Tx BD */
> - int tx_space; /* number of Tx bytes left */
> - unsigned char *tx_buf; /* pointer to free Tx area */
> - i2c_ecb_t err_cb; /* error callback function */
> -} i2c_state_t;
> -
> -
> -/* flags for i2c_send() and i2c_receive() */
> -#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */
> -#define I2CF_START_COND 0x02 /* tx: generate start condition */
> -#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */
> -
> -/* return codes */
> -#define I2CERR_NO_BUFFERS 0x01 /* no more BDs or buffer space */
> -#define I2CERR_MSG_TOO_LONG 0x02 /* tried to send/receive to much data */
> -#define I2CERR_TIMEOUT 0x03 /* timeout in i2c_doio() */
> -#define I2CERR_QUEUE_EMPTY 0x04 /* i2c_doio called without send/receive */
> -
> -/* error callback flags */
> -#define I2CECB_RX_ERR 0x10 /* this is a receive error */
> -#define I2CECB_RX_ERR_OV 0x02 /* receive overrun error */
> -#define I2CECB_RX_MASK 0x0f /* mask for error bits */
> -#define I2CECB_TX_ERR 0x20 /* this is a transmit error */
> -#define I2CECB_TX_CL 0x01 /* transmit collision error */
> -#define I2CECB_TX_UN 0x02 /* transmit underflow error */
> -#define I2CECB_TX_NAK 0x04 /* transmit no ack error */
> -#define I2CECB_TX_MASK 0x0f /* mask for error bits */
> -#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */
> -
> -/*
> - * Returns the best value of I2BRG to meet desired clock speed of I2C with
> - * input parameters (clock speed, filter, and predivider value).
> - * It returns computer speed value and the difference between it and desired
> - * speed.
> - */
> -static inline int
> -i2c_roundrate(int hz, int speed, int filter, int modval,
> - int *brgval, int *totspeed)
> -{
> - int moddiv = 1 << (5 - (modval & 3)), brgdiv, div;
> -
> - debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n",
> - hz, speed, filter, modval);
> -
> - div = moddiv * speed;
> - brgdiv = (hz + div - 1) / div;
> -
> - debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv);
> -
> - *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter);
> -
> - if ((*brgval < 0) || (*brgval > 255)) {
> - debug("\t\trejected brgval=%d\n", *brgval);
> - return -1;
> - }
> -
> - brgdiv = 2 * (*brgval + 3 + (2 * filter));
> - div = moddiv * brgdiv;
> - *totspeed = hz / div;
> -
> - debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed);
> -
> - return 0;
> -}
> -
> -/*
> - * Sets the I2C clock predivider and divider to meet required clock speed.
> - */
> -static int i2c_setrate(int hz, int speed)
> -{
> - immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
> - volatile i2c8xx_t *i2c = (i2c8xx_t *) & immap->im_i2c;
> - int brgval,
> - modval, /* 0-3 */
> - bestspeed_diff = speed,
> - bestspeed_brgval = 0,
> - bestspeed_modval = 0,
> - bestspeed_filter = 0,
> - totspeed,
> - filter = 0; /* Use this fixed value */
> -
> - for (modval = 0; modval < 4; modval++) {
> - if (i2c_roundrate
> - (hz, speed, filter, modval, &brgval, &totspeed) == 0) {
> - int diff = speed - totspeed;
> -
> - if ((diff >= 0) && (diff < bestspeed_diff)) {
> - bestspeed_diff = diff;
> - bestspeed_modval = modval;
> - bestspeed_brgval = brgval;
> - bestspeed_filter = filter;
> - }
> - }
> - }
> -
> - debug("[I2C] Best is:\n");
> - debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n",
> - hz,
> - speed,
> - bestspeed_filter,
> - bestspeed_modval,
> - bestspeed_brgval,
> - bestspeed_diff);
> -
> - i2c->i2c_i2mod |=
> - ((bestspeed_modval & 3) << 1) | (bestspeed_filter << 3);
> - i2c->i2c_i2brg = bestspeed_brgval & 0xff;
> -
> - debug("[I2C] i2mod=%08x i2brg=%08x\n",
> - i2c->i2c_i2mod,
> - i2c->i2c_i2brg);
> -
> - return 1;
> -}
> -
> -void i2c_init(int speed, int slaveaddr)
> -{
> - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
> - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
> - volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
> - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
> - ulong rbase, tbase;
> - volatile I2C_BD *rxbd, *txbd;
> - uint dpaddr;
> -
> -#ifdef CONFIG_SYS_I2C_INIT_BOARD
> - /* call board specific i2c bus reset routine before accessing the */
> - /* environment, which might be in a chip on that bus. For details */
> - /* about this problem see doc/I2C_Edge_Conditions. */
> - i2c_init_board();
> -#endif
> -
> -#ifdef CONFIG_SYS_I2C_UCODE_PATCH
> - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
> -#else
> - /* Disable relocation */
> - iip->iic_rpbase = 0;
> -#endif
> -
> - dpaddr = CPM_I2C_BASE;
> -
> - /*
> - * initialise data in dual port ram:
> - *
> - * dpaddr->rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes)
> - * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes)
> - * tx buffer (MAX_TX_SPACE bytes)
> - */
> -
> - rbase = dpaddr;
> - tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD);
> -
> - /* Initialize Port B I2C pins. */
> - cp->cp_pbpar |= 0x00000030;
> - cp->cp_pbdir |= 0x00000030;
> - cp->cp_pbodr |= 0x00000030;
> -
> - /* Disable interrupts */
> - i2c->i2c_i2mod = 0x00;
> - i2c->i2c_i2cmr = 0x00;
> - i2c->i2c_i2cer = 0xff;
> - i2c->i2c_i2add = slaveaddr;
> -
> - /*
> - * Set the I2C BRG Clock division factor from desired i2c rate
> - * and current CPU rate (we assume sccr dfbgr field is 0;
> - * divide BRGCLK by 1)
> - */
> - debug("[I2C] Setting rate...\n");
> - i2c_setrate(gd->cpu_clk, CONFIG_SYS_I2C_SPEED);
> -
> - /* Set I2C controller in master mode */
> - i2c->i2c_i2com = 0x01;
> -
> - /* Set SDMA bus arbitration level to 5 (SDCR) */
> - immap->im_siu_conf.sc_sdcr = 0x0001;
> -
> - /* Initialize Tx/Rx parameters */
> - iip->iic_rbase = rbase;
> - iip->iic_tbase = tbase;
> - rxbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_rbase]);
> - txbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_tbase]);
> -
> - debug("[I2C] rbase = %04x\n", iip->iic_rbase);
> - debug("[I2C] tbase = %04x\n", iip->iic_tbase);
> - debug("[I2C] rxbd = %08x\n", (int)rxbd);
> - debug("[I2C] txbd = %08x\n", (int)txbd);
> -
> - /* Set big endian byte order */
> - iip->iic_tfcr = 0x10;
> - iip->iic_rfcr = 0x10;
> -
> - /* Set maximum receive size. */
> - iip->iic_mrblr = I2C_RXTX_LEN;
> -
> -#ifdef CONFIG_SYS_I2C_UCODE_PATCH
> - /*
> - * Initialize required parameters if using microcode patch.
> - */
> - iip->iic_rbptr = iip->iic_rbase;
> - iip->iic_tbptr = iip->iic_tbase;
> - iip->iic_rstate = 0;
> - iip->iic_tstate = 0;
> -#else
> - cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG;
> - do {
> - __asm__ __volatile__("eieio");
> - } while (cp->cp_cpcr & CPM_CR_FLG);
> -#endif
> -
> - /* Clear events and interrupts */
> - i2c->i2c_i2cer = 0xff;
> - i2c->i2c_i2cmr = 0x00;
> -}
> -
> -static void i2c_newio(i2c_state_t *state)
> -{
> - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
> - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
> - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
> -
> - debug("[I2C] i2c_newio\n");
> -
> -#ifdef CONFIG_SYS_I2C_UCODE_PATCH
> - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
> -#endif
> - state->rx_idx = 0;
> - state->tx_idx = 0;
> - state->rxbd = (void *)&cp->cp_dpmem[iip->iic_rbase];
> - state->txbd = (void *)&cp->cp_dpmem[iip->iic_tbase];
> - state->tx_space = MAX_TX_SPACE;
> - state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD);
> - state->err_cb = NULL;
> -
> - debug("[I2C] rxbd = %08x\n", (int)state->rxbd);
> - debug("[I2C] txbd = %08x\n", (int)state->txbd);
> - debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf);
> -
> - /* clear the buffer memory */
> - memset((char *)state->tx_buf, 0, MAX_TX_SPACE);
> -}
> -
> -static int
> -i2c_send(i2c_state_t *state,
> - unsigned char address,
> - unsigned char secondary_address,
> - unsigned int flags, unsigned short size, unsigned char *dataout)
> -{
> - volatile I2C_BD *txbd;
> - int i, j;
> -
> - debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n",
> - address, secondary_address, flags, size);
> -
> - /* trying to send message larger than BD */
> - if (size > I2C_RXTX_LEN)
> - return I2CERR_MSG_TOO_LONG;
> -
> - /* no more free bds */
> - if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size))
> - return I2CERR_NO_BUFFERS;
> -
> - txbd = (I2C_BD *) state->txbd;
> - txbd->addr = state->tx_buf;
> -
> - debug("[I2C] txbd = %08x\n", (int)txbd);
> -
> - if (flags & I2CF_START_COND) {
> - debug("[I2C] Formatting addresses...\n");
> - if (flags & I2CF_ENABLE_SECONDARY) {
> - /* Length of msg + dest addr */
> - txbd->length = size + 2;
> -
> - txbd->addr[0] = address << 1;
> - txbd->addr[1] = secondary_address;
> - i = 2;
> - } else {
> - /* Length of msg + dest addr */
> - txbd->length = size + 1;
> - /* Write dest addr to BD */
> - txbd->addr[0] = address << 1;
> - i = 1;
> - }
> - } else {
> - txbd->length = size; /* Length of message */
> - i = 0;
> - }
> -
> - /* set up txbd */
> - txbd->status = BD_SC_READY;
> - if (flags & I2CF_START_COND)
> - txbd->status |= BD_I2C_TX_START;
> - if (flags & I2CF_STOP_COND)
> - txbd->status |= BD_SC_LAST | BD_SC_WRAP;
> -
> - /* Copy data to send into buffer */
> - debug("[I2C] copy data...\n");
> - for(j = 0; j < size; i++, j++)
> - txbd->addr[i] = dataout[j];
> -
> - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
> - txbd->length,
> - txbd->status,
> - txbd->addr[0],
> - txbd->addr[1]);
> -
> - /* advance state */
> - state->tx_buf += txbd->length;
> - state->tx_space -= txbd->length;
> - state->tx_idx++;
> - state->txbd = (void *) (txbd + 1);
> -
> - return 0;
> -}
> -
> -static int
> -i2c_receive(i2c_state_t *state,
> - unsigned char address,
> - unsigned char secondary_address,
> - unsigned int flags,
> - unsigned short size_to_expect, unsigned char *datain)
> -{
> - volatile I2C_BD *rxbd, *txbd;
> -
> - debug("[I2C] i2c_receive %02d %02d %02d\n",
> - address, secondary_address, flags);
> -
> - /* Expected to receive too much */
> - if (size_to_expect > I2C_RXTX_LEN)
> - return I2CERR_MSG_TOO_LONG;
> -
> - /* no more free bds */
> - if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS
> - || state->tx_space < 2)
> - return I2CERR_NO_BUFFERS;
> -
> - rxbd = (I2C_BD *) state->rxbd;
> - txbd = (I2C_BD *) state->txbd;
> -
> - debug("[I2C] rxbd = %08x\n", (int)rxbd);
> - debug("[I2C] txbd = %08x\n", (int)txbd);
> -
> - txbd->addr = state->tx_buf;
> -
> - /* set up TXBD for destination address */
> - if (flags & I2CF_ENABLE_SECONDARY) {
> - txbd->length = 2;
> - txbd->addr[0] = address << 1; /* Write data */
> - txbd->addr[1] = secondary_address; /* Internal address */
> - txbd->status = BD_SC_READY;
> - } else {
> - txbd->length = 1 + size_to_expect;
> - txbd->addr[0] = (address << 1) | 0x01;
> - txbd->status = BD_SC_READY;
> - memset(&txbd->addr[1], 0, txbd->length);
> - }
> -
> - /* set up rxbd for reception */
> - rxbd->status = BD_SC_EMPTY;
> - rxbd->length = size_to_expect;
> - rxbd->addr = datain;
> -
> - txbd->status |= BD_I2C_TX_START;
> - if (flags & I2CF_STOP_COND) {
> - txbd->status |= BD_SC_LAST | BD_SC_WRAP;
> - rxbd->status |= BD_SC_WRAP;
> - }
> -
> - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
> - txbd->length,
> - txbd->status,
> - txbd->addr[0],
> - txbd->addr[1]);
> - debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
> - rxbd->length,
> - rxbd->status,
> - rxbd->addr[0],
> - rxbd->addr[1]);
> -
> - /* advance state */
> - state->tx_buf += txbd->length;
> - state->tx_space -= txbd->length;
> - state->tx_idx++;
> - state->txbd = (void *) (txbd + 1);
> - state->rx_idx++;
> - state->rxbd = (void *) (rxbd + 1);
> -
> - return 0;
> -}
> -
> -
> -static int i2c_doio(i2c_state_t *state)
> -{
> - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
> - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
> - volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
> - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
> - volatile I2C_BD *txbd, *rxbd;
> - volatile int j = 0;
> -
> - debug("[I2C] i2c_doio\n");
> -
> -#ifdef CONFIG_SYS_I2C_UCODE_PATCH
> - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
> -#endif
> -
> - if (state->tx_idx <= 0 && state->rx_idx <= 0) {
> - debug("[I2C] No I/O is queued\n");
> - return I2CERR_QUEUE_EMPTY;
> - }
> -
> - iip->iic_rbptr = iip->iic_rbase;
> - iip->iic_tbptr = iip->iic_tbase;
> -
> - /* Enable I2C */
> - debug("[I2C] Enabling I2C...\n");
> - i2c->i2c_i2mod |= 0x01;
> -
> - /* Begin transmission */
> - i2c->i2c_i2com |= 0x80;
> -
> - /* Loop until transmit & receive completed */
> -
> - if (state->tx_idx > 0) {
> - txbd = ((I2C_BD*)state->txbd) - 1;
> -
> - debug("[I2C] Transmitting...(txbd=0x%08lx)\n",
> - (ulong)txbd);
> -
> - while ((txbd->status & BD_SC_READY) && (j++ < TOUT_LOOP)) {
> - if (ctrlc())
> - return (-1);
> -
> - __asm__ __volatile__("eieio");
> - }
> - }
> -
> - if ((state->rx_idx > 0) && (j < TOUT_LOOP)) {
> - rxbd = ((I2C_BD*)state->rxbd) - 1;
> -
> - debug("[I2C] Receiving...(rxbd=0x%08lx)\n",
> - (ulong)rxbd);
> -
> - while ((rxbd->status & BD_SC_EMPTY) && (j++ < TOUT_LOOP)) {
> - if (ctrlc())
> - return (-1);
> -
> - __asm__ __volatile__("eieio");
> - }
> - }
> -
> - /* Turn off I2C */
> - i2c->i2c_i2mod &= ~0x01;
> -
> - if (state->err_cb != NULL) {
> - int n, i, b;
> -
> - /*
> - * if we have an error callback function, look at the
> - * error bits in the bd status and pass them back
> - */
> -
> - if ((n = state->tx_idx) > 0) {
> - for (i = 0; i < n; i++) {
> - txbd = ((I2C_BD *) state->txbd) - (n - i);
> - if ((b = txbd->status & BD_I2C_TX_ERR) != 0)
> - (*state->err_cb) (I2CECB_TX_ERR | b,
> - i);
> - }
> - }
> -
> - if ((n = state->rx_idx) > 0) {
> - for (i = 0; i < n; i++) {
> - rxbd = ((I2C_BD *) state->rxbd) - (n - i);
> - if ((b = rxbd->status & BD_I2C_RX_ERR) != 0)
> - (*state->err_cb) (I2CECB_RX_ERR | b,
> - i);
> - }
> - }
> -
> - if (j >= TOUT_LOOP)
> - (*state->err_cb) (I2CECB_TIMEOUT, 0);
> - }
> -
> - return (j >= TOUT_LOOP) ? I2CERR_TIMEOUT : 0;
> -}
> -
> -static int had_tx_nak;
> -
> -static void i2c_test_callback(int flags, int xnum)
> -{
> - if ((flags & I2CECB_TX_ERR) && (flags & I2CECB_TX_NAK))
> - had_tx_nak = 1;
> -}
> -
> -int i2c_probe(uchar chip)
> -{
> - i2c_state_t state;
> - int rc;
> - uchar buf[1];
> -
> - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> -
> - i2c_newio(&state);
> -
> - state.err_cb = i2c_test_callback;
> - had_tx_nak = 0;
> -
> - rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1,
> - buf);
> -
> - if (rc != 0)
> - return (rc);
> -
> - rc = i2c_doio(&state);
> -
> - if ((rc != 0) && (rc != I2CERR_TIMEOUT))
> - return (rc);
> -
> - return (had_tx_nak);
> -}
> -
> -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> -{
> - i2c_state_t state;
> - uchar xaddr[4];
> - int rc;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
> - /*
> - * EEPROM chips that implement "address overflow" are ones like
> - * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
> - * extra bits end up in the "chip address" bit slots. This makes
> - * a 24WC08 (1Kbyte) chip look like four 256 byte chips.
> - *
> - * Note that we consider the length of the address field to still
> - * be one byte because the extra address bits are hidden in the
> - * chip address.
> - */
> - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> -#endif
> -
> - i2c_newio(&state);
> -
> - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
> - &xaddr[4 - alen]);
> - if (rc != 0) {
> - printf("i2c_read: i2c_send failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer);
> - if (rc != 0) {
> - printf("i2c_read: i2c_receive failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_doio(&state);
> - if (rc != 0) {
> - printf("i2c_read: i2c_doio failed (%d)\n", rc);
> - return 1;
> - }
> - return 0;
> -}
> -
> -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> -{
> - i2c_state_t state;
> - uchar xaddr[4];
> - int rc;
> -
> - xaddr[0] = (addr >> 24) & 0xFF;
> - xaddr[1] = (addr >> 16) & 0xFF;
> - xaddr[2] = (addr >> 8) & 0xFF;
> - xaddr[3] = addr & 0xFF;
> -
> -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
> - /*
> - * EEPROM chips that implement "address overflow" are ones like
> - * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
> - * extra bits end up in the "chip address" bit slots. This makes
> - * a 24WC08 (1Kbyte) chip look like four 256 byte chips.
> - *
> - * Note that we consider the length of the address field to still
> - * be one byte because the extra address bits are hidden in the
> - * chip address.
> - */
> - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> -#endif
> -
> - i2c_newio(&state);
> -
> - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
> - &xaddr[4 - alen]);
> - if (rc != 0) {
> - printf("i2c_write: first i2c_send failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer);
> - if (rc != 0) {
> - printf("i2c_write: second i2c_send failed (%d)\n", rc);
> - return 1;
> - }
> -
> - rc = i2c_doio(&state);
> - if (rc != 0) {
> - printf("i2c_write: i2c_doio failed (%d)\n", rc);
> - return 1;
> - }
> - return 0;
> -}
> -
> -#endif /* CONFIG_HARD_I2C */
> diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README
> index 92a83849ac..89e033e1c5 100644
> --- a/board/freescale/m52277evb/README
> +++ b/board/freescale/m52277evb/README
> @@ -83,7 +83,6 @@ CONFIG_MCFTMR -- define to use DMA timer
> CONFIG_MCFPIT -- define to use PIT timer
>
> CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
> -CONFIG_HARD_I2C -- define for I2C hardware support
> CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
> CONFIG_SYS_I2C_SPEED -- define for I2C speed
> CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
> diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README
> index 224e79c46a..2fca12c417 100644
> --- a/board/freescale/m53017evb/README
> +++ b/board/freescale/m53017evb/README
> @@ -91,7 +91,6 @@ CONFIG_MCFTMR -- define to use DMA timer
> CONFIG_MCFPIT -- define to use PIT timer
>
> CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
> -CONFIG_HARD_I2C -- define for I2C hardware support
> CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
> CONFIG_SYS_I2C_SPEED -- define for I2C speed
> CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
> diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README
> index 582e0c3d9e..757f0abdd7 100644
> --- a/board/freescale/m5373evb/README
> +++ b/board/freescale/m5373evb/README
> @@ -90,7 +90,6 @@ CONFIG_MCFTMR -- define to use DMA timer
> CONFIG_MCFPIT -- define to use PIT timer
>
> CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
> -CONFIG_HARD_I2C -- define for I2C hardware support
> CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
> CONFIG_SYS_I2C_SPEED -- define for I2C speed
> CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
> diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README
> index c563ad99a7..4a8719333a 100644
> --- a/board/freescale/m54455evb/README
> +++ b/board/freescale/m54455evb/README
> @@ -113,7 +113,6 @@ CONFIG_MCFTMR -- define to use DMA timer
> CONFIG_MCFPIT -- define to use PIT timer
>
> CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver
> -CONFIG_HARD_I2C -- define for I2C hardware support
> CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
> CONFIG_SYS_I2C_SPEED -- define for I2C speed
> CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
> diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README
> index 30c5dedafe..ce7b27b8b2 100644
> --- a/board/freescale/m547xevb/README
> +++ b/board/freescale/m547xevb/README
> @@ -98,7 +98,6 @@ CONFIG_DOS_PARTITION -- enable DOS read/write
> CONFIG_SLTTMR -- define to use SLT timer
>
> CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
> -CONFIG_HARD_I2C -- define for I2C hardware support
> CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
> CONFIG_SYS_I2C_SPEED -- define for I2C speed
> CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD Simon Glass
@ 2017-05-15 4:23 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:23 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> board/cm5200/cm5200.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
> index 2f55191caf..0c647bbd3d 100644
> --- a/board/cm5200/cm5200.c
> +++ b/board/cm5200/cm5200.c
> @@ -214,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf)
> strcat(buf, tmp);
> }
>
> -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
> +#if defined(CONFIG_SYS_I2C_SOFT)
> /*
> * Compose string with hostname.
> * buf is assumed to have enough space, and be null-terminated.
> @@ -295,7 +295,7 @@ int board_early_init_r(void)
> #ifdef CONFIG_MISC_INIT_R
> int misc_init_r(void)
> {
> -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
> +#if defined(CONFIG_SYS_I2C_SOFT)
> uchar buf[6];
> char str[18];
> char hostname[MODULE_NAME_MAXLEN];
> @@ -323,7 +323,7 @@ int misc_init_r(void)
> compose_hostname(hw_id, hostname);
> setenv("hostname", hostname);
>
> -#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
> +#endif /* defined(CONFIG_SYS_I2C_SOFT) */
> if (!getenv("ethaddr"))
> printf(LOG_PREFIX "MAC address not set, networking is not "
> "operational\n");
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 04/12] i2c: pdm360ng: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 04/12] i2c: pdm360ng: " Simon Glass
@ 2017-05-15 4:23 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:23 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> board/pdm360ng/pdm360ng.c | 30 ------------------------------
> 1 file changed, 30 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/board/pdm360ng/pdm360ng.c b/board/pdm360ng/pdm360ng.c
> index 9db31d3312..371bcd9e6b 100644
> --- a/board/pdm360ng/pdm360ng.c
> +++ b/board/pdm360ng/pdm360ng.c
> @@ -169,36 +169,6 @@ int misc_init_r(void)
> clrsetbits_be32(&im->gpio.gpdat, 0x01000000, 0x00040000);
> #endif
>
> -#if defined(CONFIG_HARD_I2C)
> - if (!getenv("ethaddr")) {
> - uchar buf[6];
> - uchar ifm_oui[3] = { 0, 2, 1, };
> - int ret;
> -
> - /* I2C-0 for on-board eeprom */
> - i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS_NUM);
> -
> - /* Read ethaddr from EEPROM */
> - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR,
> - CONFIG_SYS_I2C_EEPROM_MAC_OFFSET, 1, buf, 6);
> - if (ret != 0) {
> - printf("Error: Unable to read MAC from I2C"
> - " EEPROM at address %02X:%02X\n",
> - CONFIG_SYS_I2C_EEPROM_ADDR,
> - CONFIG_SYS_I2C_EEPROM_MAC_OFFSET);
> - return 1;
> - }
> -
> - /* Owned by IFM ? */
> - if (memcmp(buf, ifm_oui, sizeof(ifm_oui))) {
> - printf("Illegal MAC address in EEPROM: %pM\n", buf);
> - return 1;
> - }
> -
> - eth_setenv_enetaddr("ethaddr", buf);
> - }
> -#endif /* defined(CONFIG_HARD_I2C) */
> -
> return 0;
> }
>
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 05/12] i2c: keymile: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 05/12] i2c: keymile: " Simon Glass
@ 2017-05-15 4:24 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:24 UTC (permalink / raw)
To: u-boot
Hello simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> board/keymile/km82xx/km82xx.c | 5 -----
> board/keymile/km_arm/km_arm.c | 4 ----
> 2 files changed, 9 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/board/keymile/km82xx/km82xx.c b/board/keymile/km82xx/km82xx.c
> index 51b4571d40..f5a98b33e7 100644
> --- a/board/keymile/km82xx/km82xx.c
> +++ b/board/keymile/km82xx/km82xx.c
> @@ -153,13 +153,8 @@ const iop_conf_t iop_conf_tab[4][32] = {
> { 0, 0, 0, 0, 0, 0 }, /* PD18 */
> { 0, 0, 0, 0, 0, 0 }, /* PD17 */
> { 0, 0, 0, 0, 0, 0 }, /* PD16 */
> -#if defined(CONFIG_HARD_I2C)
> - { 1, 1, 1, 0, 1, 0 }, /* PD15 I2C SDA */
> - { 1, 1, 1, 0, 1, 0 }, /* PD14 I2C SCL */
> -#else
> { 1, 0, 0, 0, 1, 1 }, /* PD15 */
> { 1, 0, 0, 1, 1, 1 }, /* PD14 */
> -#endif
> { 0, 0, 0, 0, 0, 0 }, /* PD13 */
> { 0, 0, 0, 0, 0, 0 }, /* PD12 */
> { 0, 0, 0, 0, 0, 0 }, /* PD11 */
> diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
> index 079509c979..85785ffc02 100644
> --- a/board/keymile/km_arm/km_arm.c
> +++ b/board/keymile/km_arm/km_arm.c
> @@ -75,10 +75,6 @@ static const u32 kwmpp_config[] = {
> #if defined(CONFIG_SYS_I2C_SOFT)
> MPP8_GPIO, /* SDA */
> MPP9_GPIO, /* SCL */
> -#endif
> -#if defined(CONFIG_HARD_I2C)
> - MPP8_TW_SDA,
> - MPP9_TW_SCK,
> #endif
> MPP10_UART0_TXD,
> MPP11_UART0_RXD,
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 06/12] i2c: mxc_i2c: Drop use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 06/12] i2c: mxc_i2c: " Simon Glass
@ 2017-05-15 4:24 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:24 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> drivers/i2c/mxc_i2c.c | 4 ----
> 1 file changed, 4 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
> index 13ec0e63b1..b68e82770b 100644
> --- a/drivers/i2c/mxc_i2c.c
> +++ b/drivers/i2c/mxc_i2c.c
> @@ -69,10 +69,6 @@ DECLARE_GLOBAL_DATA_PTR;
> #define I2SR_IIF_CLEAR (0 << 1)
> #endif
>
> -#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE)
> -#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver"
> -#endif
> -
> #ifdef I2C_QUIRK_REG
> static u16 i2c_clk_div[60][2] = {
> { 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 },
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD Simon Glass
2017-05-13 15:22 ` Tom Rini
@ 2017-05-15 4:24 ` Heiko Schocher
1 sibling, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:24 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
>
> Changes in v3: None
> Changes in v2:
> - Add new patch to adjust omap boards to not need CONFIG_I2C_HARD
>
> board/ti/am335x/board.c | 3 ++-
> board/ti/am43xx/board.c | 3 ++-
> 2 files changed, 4 insertions(+), 2 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
> index 3e81521399..517965c0f0 100644
> --- a/board/ti/am335x/board.c
> +++ b/board/ti/am335x/board.c
> @@ -72,7 +72,8 @@ void do_board_detect(void)
> enable_i2c0_pin_mux();
> i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
>
> - if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR))
> + if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
> + CONFIG_EEPROM_CHIP_ADDRESS))
> printf("ti_i2c_eeprom_init failed\n");
> }
> #endif
> diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
> index f633e2f85d..f44103d4d6 100644
> --- a/board/ti/am43xx/board.c
> +++ b/board/ti/am43xx/board.c
> @@ -42,7 +42,8 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
> #ifdef CONFIG_TI_I2C_BOARD_DETECT
> void do_board_detect(void)
> {
> - if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR))
> + if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
> + CONFIG_EEPROM_CHIP_ADDRESS))
> printf("ti_i2c_eeprom_init failed\n");
> }
> #endif
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD
2017-05-13 3:09 ` [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD Simon Glass
2017-05-13 15:22 ` Tom Rini
@ 2017-05-15 4:25 ` Heiko Schocher
1 sibling, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:25 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> Drop use of this long-deprecated option.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3:
> - Update commit message so that it is unique in the series
> - Fix up #ifdef in cmd/eeprom.c
> - Drop changes to include/config headers
>
> Changes in v2:
> - Drop changes to omap board.c files
>
> README | 16 ++++++++--------
> cmd/eeprom.c | 2 --
> common/board_f.c | 4 ++--
> common/stdio.c | 5 +----
> scripts/config_whitelist.txt | 1 -
> 5 files changed, 11 insertions(+), 17 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/README b/README
> index 86f0814f79..11fa84ccc4 100644
> --- a/README
> +++ b/README
> @@ -2204,7 +2204,9 @@ The following options need to be configured:
>
> If you do not have i2c muxes on your board, omit this define.
>
> -- Legacy I2C Support: CONFIG_HARD_I2C
> +----under removal:
> +
> +- Legacy I2C Support: CONFIG_SOFT_I2C
>
> NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
> provides the following compelling advantages:
> @@ -2213,14 +2215,12 @@ The following options need to be configured:
> - approved multibus support
> - better i2c mux support
>
> - ** CONFIG_HARD_I2C is now being removed **
> -
> -----under removal:
> + ** CONFIG_SOFT_I2C is now being removed **
>
> - In both cases you will need to define CONFIG_SYS_I2C_SPEED
> - to be the frequency (in Hz) at which you wish your i2c bus
> - to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
> - the CPU's i2c node address).
> + With CONFIG_SOFT_I2C you will need to define
> + CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you
> + wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the
> + address of this node (ie the CPU's i2c node address).
>
> Now, the u-boot i2c code for the mpc8xx
> (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
> diff --git a/cmd/eeprom.c b/cmd/eeprom.c
> index 0a0e4a2c1c..e43566bc56 100644
> --- a/cmd/eeprom.c
> +++ b/cmd/eeprom.c
> @@ -73,11 +73,9 @@ void eeprom_init(int bus)
> #endif
>
> /* I2C EEPROM */
> -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
> #if defined(CONFIG_SYS_I2C)
> if (bus >= 0)
> i2c_set_bus_num(bus);
> -#endif
> i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> #endif
> }
> diff --git a/common/board_f.c b/common/board_f.c
> index d9431ee79a..eed3e7be2a 100644
> --- a/common/board_f.c
> +++ b/common/board_f.c
> @@ -184,7 +184,7 @@ __weak int dram_init_banksize(void)
> return 0;
> }
>
> -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
> +#if defined(CONFIG_SYS_I2C)
> static int init_func_i2c(void)
> {
> puts("I2C: ");
> @@ -765,7 +765,7 @@ static const init_fnc_t init_sequence_f[] = {
> misc_init_f,
> #endif
> INIT_FUNC_WATCHDOG_RESET
> -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
> +#if defined(CONFIG_SYS_I2C)
> init_func_i2c,
> #endif
> #if defined(CONFIG_HARD_SPI)
> diff --git a/common/stdio.c b/common/stdio.c
> index 4d30017530..ee4f0bda9e 100644
> --- a/common/stdio.c
> +++ b/common/stdio.c
> @@ -21,7 +21,7 @@
> #include <logbuff.h>
> #endif
>
> -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
> +#if defined(CONFIG_SYS_I2C)
> #include <i2c.h>
> #endif
>
> @@ -346,9 +346,6 @@ int stdio_add_devices(void)
> #ifdef CONFIG_SYS_I2C
> i2c_init_all();
> #else
> -#if defined(CONFIG_HARD_I2C)
> - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> -#endif
> #endif
> #ifdef CONFIG_DM_VIDEO
> /*
> diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
> index 7646bb6842..da37e49c83 100644
> --- a/scripts/config_whitelist.txt
> +++ b/scripts/config_whitelist.txt
> @@ -1134,7 +1134,6 @@ CONFIG_G_DNL_UMS_VENDOR_NUM
> CONFIG_H264_FREQ
> CONFIG_H8300
> CONFIG_HALEAKALA
> -CONFIG_HARD_I2C
> CONFIG_HARD_SPI
> CONFIG_HASH_VERIFY
> CONFIG_HAS_DATAFLASH
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX
2017-05-13 3:09 ` [U-Boot] [PATCH v3 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX Simon Glass
@ 2017-05-15 4:25 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:25 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> This option is not used in U-Boot. Drop it.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> README | 2 --
> 1 file changed, 2 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/README b/README
> index 11fa84ccc4..9f9265dc6d 100644
> --- a/README
> +++ b/README
> @@ -2228,8 +2228,6 @@ The following options need to be configured:
> eg, MPC823e User's Manual p.16-473). So, set
> CONFIG_SYS_I2C_SLAVE to 0.
>
> - CONFIG_SYS_I2C_INIT_MPC5XXX
> -
> When a board is reset during an i2c bus transfer
> chips might think that the current transfer is still
> in progress. Reset the slave devices by sending start
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT
2017-05-13 3:09 ` [U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT Simon Glass
@ 2017-05-15 4:25 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:25 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> This option is not used by any boards. Drop it.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> README | 11 -----------
> drivers/i2c/fsl_i2c.c | 9 ---------
> drivers/i2c/fti2c010.c | 9 ---------
> include/i2c.h | 3 ---
> scripts/config_whitelist.txt | 1 -
> 5 files changed, 33 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/README b/README
> index 9f9265dc6d..96ce6289ea 100644
> --- a/README
> +++ b/README
> @@ -2323,17 +2323,6 @@ The following options need to be configured:
> custom i2c_init_board() routine in boards/xxx/board.c
> is run early in the boot sequence.
>
> - CONFIG_SYS_I2C_BOARD_LATE_INIT
> -
> - An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
> - defined a custom i2c_board_late_init() routine in
> - boards/xxx/board.c is run AFTER the operations in i2c_init()
> - is completed. This callpoint can be used to unreset i2c bus
> - using CPU i2c controller register accesses for CPUs whose i2c
> - controller provide such a method. It is called at the end of
> - i2c_init() to allow i2c_init operations to setup the i2c bus
> - controller on the CPU (e.g. setting bus speed & slave address).
> -
> CONFIG_I2CFAST (PPC405GP|PPC405EP only)
>
> This option enables configuration of bi_iic_fast[] flags
> diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
> index a1406baa87..ff3dc25927 100644
> --- a/drivers/i2c/fsl_i2c.c
> +++ b/drivers/i2c/fsl_i2c.c
> @@ -284,15 +284,6 @@ static void __i2c_init(const struct fsl_i2c_base *base, int speed, int
>
> break;
> }
> -
> -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
> - /* Call board specific i2c bus reset routine AFTER the bus has been
> - * initialized. Use either this callpoint or i2c_init_board;
> - * which is called before i2c_init operations.
> - * For details about this problem see doc/I2C_Edge_Conditions.
> - */
> - i2c_board_late_init();
> -#endif
> }
>
> static int
> diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c
> index b35d0d2d9c..4da959fa53 100644
> --- a/drivers/i2c/fti2c010.c
> +++ b/drivers/i2c/fti2c010.c
> @@ -146,15 +146,6 @@ static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr)
> set_i2c_bus_speed(chip, speed);
>
> /* slave init, don't care */
> -
> -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
> - /* Call board specific i2c bus reset routine AFTER the bus has been
> - * initialized. Use either this callpoint or i2c_init_board;
> - * which is called before fti2c010_init operations.
> - * For details about this problem see doc/I2C_Edge_Conditions.
> - */
> - i2c_board_late_init();
> -#endif
> }
>
> /*
> diff --git a/include/i2c.h b/include/i2c.h
> index cd7f61e1c1..a88cc7cddf 100644
> --- a/include/i2c.h
> +++ b/include/i2c.h
> @@ -706,9 +706,6 @@ void i2c_early_init_f(void);
> #endif
> void i2c_init(int speed, int slaveaddr);
> void i2c_init_board(void);
> -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
> -void i2c_board_late_init(void);
> -#endif
>
> #ifdef CONFIG_SYS_I2C
> /*
> diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
> index da37e49c83..5cdca33f87 100644
> --- a/scripts/config_whitelist.txt
> +++ b/scripts/config_whitelist.txt
> @@ -4222,7 +4222,6 @@ CONFIG_SYS_I2C_BASE2
> CONFIG_SYS_I2C_BASE3
> CONFIG_SYS_I2C_BASE4
> CONFIG_SYS_I2C_BASE5
> -CONFIG_SYS_I2C_BOARD_LATE_INIT
> CONFIG_SYS_I2C_BOOT_EEPROM_ADDR
> CONFIG_SYS_I2C_BUSES
> CONFIG_SYS_I2C_BUS_MAX
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 11/12] Drop CONFIG_I2CFAST
2017-05-13 3:09 ` [U-Boot] [PATCH v3 11/12] Drop CONFIG_I2CFAST Simon Glass
@ 2017-05-15 4:26 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:26 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:09 schrieb Simon Glass:
> This option is not used in U-Boot. Drop it.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> README | 6 ------
> common/board_r.c | 17 -----------------
> scripts/config_whitelist.txt | 1 -
> 3 files changed, 24 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/README b/README
> index 96ce6289ea..71d8de0ba8 100644
> --- a/README
> +++ b/README
> @@ -2323,12 +2323,6 @@ The following options need to be configured:
> custom i2c_init_board() routine in boards/xxx/board.c
> is run early in the boot sequence.
>
> - CONFIG_I2CFAST (PPC405GP|PPC405EP only)
> -
> - This option enables configuration of bi_iic_fast[] flags
> - in u-boot bd_info structure based on u-boot environment
> - variable "i2cfast". (see also i2cfast)
> -
> CONFIG_I2C_MULTI_BUS
>
> This option allows the use of multiple I2C buses, each of which
> diff --git a/common/board_r.c b/common/board_r.c
> index d69a33c4a3..dba2102b18 100644
> --- a/common/board_r.c
> +++ b/common/board_r.c
> @@ -485,24 +485,7 @@ static int initr_env(void)
>
> /* Initialize from environment */
> load_addr = getenv_ulong("loadaddr", 16, load_addr);
> -#if defined(CONFIG_SYS_EXTBDINFO)
> -#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
> -#if defined(CONFIG_I2CFAST)
> - /*
> - * set bi_iic_fast for linux taking environment variable
> - * "i2cfast" into account
> - */
> - {
> - char *s = getenv("i2cfast");
>
> - if (s && ((*s == 'y') || (*s == 'Y'))) {
> - gd->bd->bi_iic_fast[0] = 1;
> - gd->bd->bi_iic_fast[1] = 1;
> - }
> - }
> -#endif /* CONFIG_I2CFAST */
> -#endif /* CONFIG_405GP, CONFIG_405EP */
> -#endif /* CONFIG_SYS_EXTBDINFO */
> return 0;
> }
>
> diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
> index 5cdca33f87..7cdfcd0a52 100644
> --- a/scripts/config_whitelist.txt
> +++ b/scripts/config_whitelist.txt
> @@ -1319,7 +1319,6 @@ CONFIG_HW_ENV_SETTINGS
> CONFIG_HW_WATCHDOG
> CONFIG_HW_WATCHDOG_TIMEOUT_MS
> CONFIG_I2C
> -CONFIG_I2CFAST
> CONFIG_I2C_CHIPADDRESS
> CONFIG_I2C_CMD_TREE
> CONFIG_I2C_ENV_EEPROM_BUS
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
* [U-Boot] [PATCH v3 12/12] Drop use of CONFIG_I2C_SOFT
2017-05-13 3:10 ` [U-Boot] [PATCH v3 12/12] Drop use of CONFIG_I2C_SOFT Simon Glass
@ 2017-05-15 4:26 ` Heiko Schocher
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Schocher @ 2017-05-15 4:26 UTC (permalink / raw)
To: u-boot
Hello Simon,
Am 13.05.2017 um 05:10 schrieb Simon Glass:
> This option is not used in U-Boot. Drop it.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3:
> - Rebase to master
>
> Changes in v2:
> - Rebase to master
>
> README | 32 +-------------------------------
> 1 file changed, 1 insertion(+), 31 deletions(-)
Thanks!
Applied to u-boot-i2c.git master
u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665
bye,
Heiko
>
> diff --git a/README b/README
> index 71d8de0ba8..9525199551 100644
> --- a/README
> +++ b/README
> @@ -2204,37 +2204,7 @@ The following options need to be configured:
>
> If you do not have i2c muxes on your board, omit this define.
>
> -----under removal:
> -
> -- Legacy I2C Support: CONFIG_SOFT_I2C
> -
> - NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
> - provides the following compelling advantages:
> -
> - - more than one i2c adapter is usable
> - - approved multibus support
> - - better i2c mux support
> -
> - ** CONFIG_SOFT_I2C is now being removed **
> -
> - With CONFIG_SOFT_I2C you will need to define
> - CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you
> - wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the
> - address of this node (ie the CPU's i2c node address).
> -
> - Now, the u-boot i2c code for the mpc8xx
> - (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
> - and so its address should therefore be cleared to 0 (See,
> - eg, MPC823e User's Manual p.16-473). So, set
> - CONFIG_SYS_I2C_SLAVE to 0.
> -
> - When a board is reset during an i2c bus transfer
> - chips might think that the current transfer is still
> - in progress. Reset the slave devices by sending start
> - commands until the slave device responds.
> -
> - That's all that's required for CONFIG_HARD_I2C.
> -
> +- Legacy I2C Support:
> If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
> then the following macros need to be defined (examples are
> from include/configs/lwmon.h):
>
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2017-05-15 4:26 UTC | newest]
Thread overview: 27+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-05-13 3:09 [U-Boot] [PATCH v3 00/12] i2c: Remove old I2C support Simon Glass
2017-05-13 3:09 ` [U-Boot] [PATCH v3 01/12] i2c: Drop use of CONFIG_I2C_HARD Simon Glass
2017-05-15 4:22 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C Simon Glass
2017-05-15 4:23 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD Simon Glass
2017-05-15 4:23 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 04/12] i2c: pdm360ng: " Simon Glass
2017-05-15 4:23 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 05/12] i2c: keymile: " Simon Glass
2017-05-15 4:24 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 06/12] i2c: mxc_i2c: " Simon Glass
2017-05-15 4:24 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD Simon Glass
2017-05-13 15:22 ` Tom Rini
2017-05-15 4:24 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD Simon Glass
2017-05-13 15:22 ` Tom Rini
2017-05-15 4:25 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX Simon Glass
2017-05-15 4:25 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT Simon Glass
2017-05-15 4:25 ` Heiko Schocher
2017-05-13 3:09 ` [U-Boot] [PATCH v3 11/12] Drop CONFIG_I2CFAST Simon Glass
2017-05-15 4:26 ` Heiko Schocher
2017-05-13 3:10 ` [U-Boot] [PATCH v3 12/12] Drop use of CONFIG_I2C_SOFT Simon Glass
2017-05-15 4:26 ` Heiko Schocher
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.