From: <thomas.langer-th3ZBGNqt+7QT0dZR+AlfA@public.gmane.org> To: <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>, <pekon-l0cyMroinI0@public.gmane.org> Cc: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org, sourav.poddar-l0cyMroinI0@public.gmane.org, tpiepho-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, wangyuhang2014-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org Subject: RE: support DUAL and QUAD[patch v1] Date: Mon, 22 Jul 2013 11:21:58 +0000 [thread overview] Message-ID: <593AEF6C47F46446852B067021A273D6D97E2ED4@MUCSE039.lantiq.com> (raw) In-Reply-To: <51ED0A57.4060105-KZfg59tc24xl57MIdRCFDg@public.gmane.org> Hello Huang, Huang Shijie wrote on 2013-07-22: > 于 2013年07月22日 17:56, Gupta, Pekon 写道: >> (b) struct spi_transfer: if each transfer of same message need to be >> transferred at different width. Example: Command @ Single-SPI >> followed by Data @ Quad-SPI > I am coding the QuadSpi driver for Freescale's Vybrid now. > > I think we dot need to change the spi code. the spi layer should not > know the different width of the command and the data, let the qspi > driver does it. NO! > > In the m25p_probe(), after we knows that the qspi driver and flash > support the Quad read, so we can set the > m25p->read_opcode to 0xeb or 0xec. In the qspi driver, it can do the > real job. No, the qspi driver (as example here) should provide a transparent interface only, and the mp25p80 driver, which knows the details of the flash, has to provide the information which parts of a transfer has to be done in single-/dual- or quad-mode. Otherwise you always need to extend the qspi driver for new flashes. > > thanks > Huang Shijie > Best Regards, Thomas ------------------------------------------------------------------------------ See everything from the browser to the database with AppDynamics Get end-to-end visibility with application monitoring from AppDynamics Isolate bottlenecks and diagnose root cause in seconds. Start your free trial of AppDynamics Pro today! http://pubads.g.doubleclick.net/gampad/clk?id=48808831&iu=/4140/ostg.clktrk _______________________________________________ spi-devel-general mailing list spi-devel-general@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/spi-devel-general
WARNING: multiple messages have this Message-ID (diff)
From: <thomas.langer@lantiq.com> To: <b32955@freescale.com>, <pekon@ti.com> Cc: broonie@kernel.org, linux-mtd@lists.infradead.org, spi-devel-general@lists.sourceforge.net, sourav.poddar@ti.com, tpiepho@gmail.com, wangyuhang2014@gmail.com Subject: RE: support DUAL and QUAD[patch v1] Date: Mon, 22 Jul 2013 11:21:58 +0000 [thread overview] Message-ID: <593AEF6C47F46446852B067021A273D6D97E2ED4@MUCSE039.lantiq.com> (raw) In-Reply-To: <51ED0A57.4060105@freescale.com> Hello Huang, Huang Shijie wrote on 2013-07-22: > 于 2013年07月22日 17:56, Gupta, Pekon 写道: >> (b) struct spi_transfer: if each transfer of same message need to be >> transferred at different width. Example: Command @ Single-SPI >> followed by Data @ Quad-SPI > I am coding the QuadSpi driver for Freescale's Vybrid now. > > I think we dot need to change the spi code. the spi layer should not > know the different width of the command and the data, let the qspi > driver does it. NO! > > In the m25p_probe(), after we knows that the qspi driver and flash > support the Quad read, so we can set the > m25p->read_opcode to 0xeb or 0xec. In the qspi driver, it can do the > real job. No, the qspi driver (as example here) should provide a transparent interface only, and the mp25p80 driver, which knows the details of the flash, has to provide the information which parts of a transfer has to be done in single-/dual- or quad-mode. Otherwise you always need to extend the qspi driver for new flashes. > > thanks > Huang Shijie > Best Regards, Thomas
next prev parent reply other threads:[~2013-07-22 11:21 UTC|newest] Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top 2013-07-10 8:34 SPI: support DUAL and QUAD[patch v1] yuhang wang 2013-07-10 8:34 ` yuhang wang [not found] ` <CAHSAbzP0Nc1ahf_ra6yDuMvV998_+EGcUOGDv5ifKaagYf+NOg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> 2013-07-16 8:08 ` Gupta, Pekon 2013-07-16 8:08 ` Gupta, Pekon [not found] ` <20980858CB6D3A4BAE95CA194937D5E73E9E84D2-yXqyApvAXouIQmiDNMet8wC/G2K4zDHf@public.gmane.org> 2013-07-16 8:59 ` yuhang wang 2013-07-16 8:59 ` yuhang wang [not found] ` <CAHSAbzMDOWo5oBqUHqMxybuDwUjFbczYwN+85gH+rxZ9z8u2Pw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> 2013-07-16 9:11 ` Gupta, Pekon 2013-07-16 9:11 ` Gupta, Pekon [not found] ` <20980858CB6D3A4BAE95CA194937D5E73E9E851E-yXqyApvAXouIQmiDNMet8wC/G2K4zDHf@public.gmane.org> 2013-07-16 10:12 ` thomas.langer-th3ZBGNqt+7QT0dZR+AlfA 2013-07-16 10:12 ` thomas.langer [not found] ` <593AEF6C47F46446852B067021A273D6D93B49E1-6yu8tajIPx7U45ihrnOXy0EOCMrvLtNR@public.gmane.org> 2013-07-16 11:20 ` Gupta, Pekon 2013-07-16 11:20 ` Gupta, Pekon [not found] ` <20980858CB6D3A4BAE95CA194937D5E73E9E85D0-yXqyApvAXouIQmiDNMet8wC/G2K4zDHf@public.gmane.org> 2013-07-16 11:59 ` yuhang wang 2013-07-16 11:59 ` yuhang wang 2013-07-16 12:18 ` thomas.langer-th3ZBGNqt+7QT0dZR+AlfA 2013-07-16 12:18 ` thomas.langer 2013-07-18 1:58 ` yuhang wang 2013-07-18 1:58 ` yuhang wang [not found] ` <CAHSAbzP5jqHwCm0qhu=DiNzpP0swqWHsQ0=MnF+EKaSN22E5hg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> 2013-07-18 2:25 ` Trent Piepho 2013-07-18 2:25 ` Trent Piepho [not found] ` <CA+7tXihoZZhpoyvxj58c+Zi-Zy631kK5s-kDoSxPKq=ej0qyvA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> 2013-07-19 2:24 ` yuhang wang 2013-07-19 2:24 ` yuhang wang 2013-07-19 19:34 ` Gupta, Pekon 2013-07-19 19:34 ` Gupta, Pekon 2013-07-22 9:33 ` Mark Brown 2013-07-22 9:33 ` Mark Brown [not found] ` <20130722093342.GJ9858-GFdadSzt00ze9xe1eoZjHA@public.gmane.org> 2013-07-22 9:56 ` Gupta, Pekon 2013-07-22 9:56 ` Gupta, Pekon 2013-07-22 10:32 ` Huang Shijie 2013-07-22 10:32 ` Huang Shijie [not found] ` <51ED0A57.4060105-KZfg59tc24xl57MIdRCFDg@public.gmane.org> 2013-07-22 11:21 ` thomas.langer-th3ZBGNqt+7QT0dZR+AlfA [this message] 2013-07-22 11:21 ` thomas.langer 2013-07-22 12:55 ` Gupta, Pekon 2013-07-22 12:55 ` Gupta, Pekon [not found] ` <20980858CB6D3A4BAE95CA194937D5E73E9ECAFC-yXqyApvAXouIQmiDNMet8wC/G2K4zDHf@public.gmane.org> 2013-07-23 2:24 ` Huang Shijie 2013-07-23 2:24 ` Huang Shijie [not found] ` <20980858CB6D3A4BAE95CA194937D5E73E9EC9B1-yXqyApvAXouIQmiDNMet8wC/G2K4zDHf@public.gmane.org> 2013-07-27 11:35 ` yuhang wang 2013-07-27 11:35 ` yuhang wang 2013-07-16 9:29 ` Mark Brown 2013-07-16 9:29 ` Mark Brown
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=593AEF6C47F46446852B067021A273D6D97E2ED4@MUCSE039.lantiq.com \ --to=thomas.langer-th3zbgnqt+7qt0dzr+alfa@public.gmane.org \ --cc=b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org \ --cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \ --cc=linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \ --cc=pekon-l0cyMroinI0@public.gmane.org \ --cc=sourav.poddar-l0cyMroinI0@public.gmane.org \ --cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \ --cc=tpiepho-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \ --cc=wangyuhang2014-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.