* Re: [<Documentation][PATCH] Update to Krogoth [not found] <1472057811-31302-1-git-send-email-Thomas.Thorne@Net2Edge.com> @ 2016-09-01 14:28 ` Thomas A. F. Thorne MEng AUS MIET 2016-09-01 18:29 ` Otavio Salvador 0 siblings, 1 reply; 17+ messages in thread From: Thomas A. F. Thorne MEng AUS MIET @ 2016-09-01 14:28 UTC (permalink / raw) To: meta-freescale [-- Attachment #1.1: Type: text/plain, Size: 3744 bytes --] Should I be able to see patches submitted to the meta-freescale@yoctoproject.org in the meta-freescale Archives or in my inbox once they are published to the list? Do patches go through some kind of review before they are posted to the wider distribution list? I tried to send a patch for some of user guide documentation last week but have not seen anything of it yet. I did notice that by copy and pasting my way through the documentation instructions I ended up with [<Documentation] in my subject, which looked a bit odd. I tried to submit the patch again on the 31st with an adjusted subject that started [Documentation] but I have not seen anything of that either. My non-patch message made it out within 3 hours. Thomas Thorne Software Engineer Net2Edge Limited On 24/08/16 17:56, Thomas Thorne wrote: > Replace 'Jethro' with 'Krogoth' and '2.0' with '2.1' > > Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com> > --- > FAQ/source/conf.py | 6 +++--- > release-notes/source/conf.py | 2 +- > user-guide/source/conf.py | 6 +++--- > user-guide/source/nsteps.rst | 2 +- > 4 files changed, 8 insertions(+), 8 deletions(-) > > diff --git a/FAQ/source/conf.py b/FAQ/source/conf.py > index a2792a6..00eaebd 100644 > --- a/FAQ/source/conf.py > +++ b/FAQ/source/conf.py > @@ -47,10 +47,10 @@ copyright = u'2014, Freescale Community BSP Team' > # |version| and |release|, also used in various other places throughout the > # built documents. > # > -# The short X.Y version. > -version = '1.5' > +# The short X.Y version or version name if applicable. > +version = 'krogoth' > # The full version, including alpha/beta/rc tags. > -release = '1.5' > +release = '2.1' > > # The language for content autogenerated by Sphinx. Refer to documentation > # for a list of supported languages. > diff --git a/release-notes/source/conf.py b/release-notes/source/conf.py > index 6115217..0ea97f1 100644 > --- a/release-notes/source/conf.py > +++ b/release-notes/source/conf.py > @@ -50,7 +50,7 @@ copyright = u'2013-2016, FSL Community BSP Team' > # |version| and |release|, also used in various other places throughout the > # built documents. > # > -# The short X.Y version. > +# The short X.Y version or version name if applicable. > version = 'krogoth' > # The full version, including alpha/beta/rc tags. > release = '2.1' > diff --git a/user-guide/source/conf.py b/user-guide/source/conf.py > index 558f919..7c9f536 100644 > --- a/user-guide/source/conf.py > +++ b/user-guide/source/conf.py > @@ -47,10 +47,10 @@ copyright = u'2014, Freescale Community BSP Team' > # |version| and |release|, also used in various other places throughout the > # built documents. > # > -# The short X.Y version. > -version = '1.6' > +# The short X.Y version or version name if applicable. > +version = 'krogoth' > # The full version, including alpha/beta/rc tags. > -release = '1.6' > +release = '2.1' > > # The language for content autogenerated by Sphinx. Refer to documentation > # for a list of supported languages. > diff --git a/user-guide/source/nsteps.rst b/user-guide/source/nsteps.rst > index df1c107..a64cca7 100644 > --- a/user-guide/source/nsteps.rst > +++ b/user-guide/source/nsteps.rst > @@ -16,7 +16,7 @@ Build and boot in *N*-steps > $ cd fsl-community-bsp > fsl-community-bsp $ repo init \ > -u https://github.com/Freescale/fsl-community-bsp-platform \ > - -b jethro > + -b krogoth > fsl-community-bsp $ repo sync > > 4. Select your machine (:ref:`machines`) and prepare the environment for bitbake:: [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 484 bytes --] ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-01 14:28 ` [<Documentation][PATCH] Update to Krogoth Thomas A. F. Thorne MEng AUS MIET @ 2016-09-01 18:29 ` Otavio Salvador 2016-09-08 18:40 ` Thomas Thorne 0 siblings, 1 reply; 17+ messages in thread From: Otavio Salvador @ 2016-09-01 18:29 UTC (permalink / raw) To: Thomas.Thorne; +Cc: meta-freescale On Thu, Sep 1, 2016 at 11:28 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: > Should I be able to see patches submitted to the > meta-freescale@yoctoproject.org in the meta-freescale Archives or in my > inbox once they are published to the list? Yes but you need to subscribe. > Do patches go through some kind of review before they are posted to the > wider distribution list? No; once you subscribe you can send the patches. > I tried to send a patch for some of user guide documentation last week > but have not seen anything of it yet. I did notice that by copy and > pasting my way through the documentation instructions I ended up with > [<Documentation] in my subject, which looked a bit odd. I tried to > submit the patch again on the 31st with an adjusted subject that started > [Documentation] but I have not seen anything of that either. My > non-patch message made it out within 3 hours. Please subscribe and resend. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-01 18:29 ` Otavio Salvador @ 2016-09-08 18:40 ` Thomas Thorne 2016-09-08 19:00 ` Otavio Salvador 0 siblings, 1 reply; 17+ messages in thread From: Thomas Thorne @ 2016-09-08 18:40 UTC (permalink / raw) To: Otavio Salvador; +Cc: meta-freescale [-- Attachment #1: Type: text/plain, Size: 1508 bytes --] I've been subscribed for weeks. I can resend again once I return to work in about one weeks time. Even if I was not subscribed, I'd expect to see them in the archive. I have looked but not found them so far. Thomas Thorne - Software Engineer - Net2Edge Sent from my Xperia Z3 Compact ---- Otavio Salvador wrote ---- On Thu, Sep 1, 2016 at 11:28 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: > Should I be able to see patches submitted to the > meta-freescale@yoctoproject.org in the meta-freescale Archives or in my > inbox once they are published to the list? Yes but you need to subscribe. > Do patches go through some kind of review before they are posted to the > wider distribution list? No; once you subscribe you can send the patches. > I tried to send a patch for some of user guide documentation last week > but have not seen anything of it yet. I did notice that by copy and > pasting my way through the documentation instructions I ended up with > [<Documentation] in my subject, which looked a bit odd. I tried to > submit the patch again on the 31st with an adjusted subject that started > [Documentation] but I have not seen anything of that either. My > non-patch message made it out within 3 hours. Please subscribe and resend. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 [-- Attachment #2: Type: text/html, Size: 2464 bytes --] ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-08 18:40 ` Thomas Thorne @ 2016-09-08 19:00 ` Otavio Salvador 2016-09-20 9:15 ` Thomas Thorne 0 siblings, 1 reply; 17+ messages in thread From: Otavio Salvador @ 2016-09-08 19:00 UTC (permalink / raw) To: Thomas Thorne; +Cc: meta-freescale On Thu, Sep 8, 2016 at 3:40 PM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > Even if I was not subscribed, I'd expect to see them in the archive. I have > looked but not found them so far. Only if it was accepted; it may have been discarded due to the mailing list setup. Please rebase the patches and resend them once you are back to work. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-08 19:00 ` Otavio Salvador @ 2016-09-20 9:15 ` Thomas Thorne 2016-09-21 11:24 ` Otavio Salvador 0 siblings, 1 reply; 17+ messages in thread From: Thomas Thorne @ 2016-09-20 9:15 UTC (permalink / raw) To: Otavio Salvador; +Cc: meta-freescale There seem to be no further changes to the documentation repository so I have resent the old patches. I have copies of the 3 emails in my inbox as I CCed myself this time. All three patches that I submitted this morning start their subject line with "[Documentation][PATCH]" On Thu, Sep 8, 2016 at 3:40 PM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > Even if I was not subscribed, I'd expect to see them in the archive. I > have looked but not found them so far. Only if it was accepted; it may have been discarded due to the mailing list setup. Please rebase the patches and resend them once you are back to work. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-20 9:15 ` Thomas Thorne @ 2016-09-21 11:24 ` Otavio Salvador 2016-09-21 11:51 ` Thomas Thorne 0 siblings, 1 reply; 17+ messages in thread From: Otavio Salvador @ 2016-09-21 11:24 UTC (permalink / raw) To: Thomas Thorne, Daiane Angolini; +Cc: meta-freescale On Tue, Sep 20, 2016 at 6:15 AM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > There seem to be no further changes to the documentation repository so I have resent the old patches. I have copies of the 3 emails in my inbox as I CCed myself this time. All three patches that I submitted this morning start their subject line with "[Documentation][PATCH]" We did not receive them. I am adding Daiane on Cc so she can also keep an eye on this. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 11:24 ` Otavio Salvador @ 2016-09-21 11:51 ` Thomas Thorne 2016-09-21 12:03 ` Otavio Salvador 0 siblings, 1 reply; 17+ messages in thread From: Thomas Thorne @ 2016-09-21 11:51 UTC (permalink / raw) To: Otavio Salvador, Daiane Angolini; +Cc: meta-freescale How strange. I have attempted to test if it is my client failing to send or my mail server refusing to deliver outside. To do so I hand edited one of my patch files into a new email and used the same git command to send the message. I received a copy of the email almost instantly in Outlook, which is running on another machine. I am confident that a message made it at least as far as the Exchange server for my office. The email I received was: -----Original Message----- From: Thomas Thorne [mailto:Thomas.Thorne@Net2Edge.com] Sent: 21 September 2016 12:34 To: meta-freescale@yoctoproject.org Cc: Thomas Thorne <Thomas.Thorne@net2edge.com>; otavio.salvador@ossystems.com.br Subject: [Documentation][PATCH] Not Really - This is a hand made test Try and make a message body by hand. Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com> I'll drop the diff stuff for now. I will attempt to send this using the following command: $ git send-email --to meta-freescale@yoctoproject.org --cc Thomas.Thorne@Net2Edge.com --cc otavio.salvador@ossystems.com.br 0001-Hand-Made-Test.patch Maybe I cannot send emails externally through git or something weird like that. CCing Otavio Salvador and myself to check whether it is the list that fails to get this or everthing. I kept the [Documentation][PATCH] bit of the Subject as that was all that was common between the patches. Also update the Date: field by hand. ----- The terminal output when I executed the command was: $ git send-email --to meta-freescale@yoctoproject.org --cc Thomas.Thorne@Net2Edge.com --cc otavio.salvador@ossystems.com.br 0001-Hand-Made-Test.patch 0001-Hand-Made-Test.patch (mbox) Adding cc: Thomas Thorne <Thomas.Thorne@Net2Edge.com> from line 'From: Thomas Thorne <Thomas.Thorne@Net2Edge.com>' (body) Adding cc: Thomas Thorne <Thomas.Thorne@Net2Edge.com> from line 'Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com>' From: Thomas Thorne <Thomas.Thorne@Net2Edge.com> To: meta-freescale@yoctoproject.org Cc: Thomas.Thorne@Net2Edge.com, otavio.salvador@ossystems.com.br Subject: [Documentation][PATCH] Not Really - This is a hand made test Date: Wed, 21 Sep 2016 12:34:07 +0100 Message-Id: <1474457647-16977-1-git-send-email-Thomas.Thorne@Net2Edge.com> X-Mailer: git-send-email 2.7.4 The Cc list above has been expanded by additional addresses found in the patch commit message. By default send-email prompts before sending whenever this occurs. This behavior is controlled by the sendemail.confirm configuration setting. For additional information, run 'git send-email --help'. To retain the current behavior, but squelch this message, run 'git config --global sendemail.confirm auto'. Send this email? ([y]es|[n]o|[q]uit|[a]ll): yes OK. Log says: Sendmail: /usr/sbin/sendmail -i meta-freescale@yoctoproject.org Thomas.Thorne@Net2Edge.com otavio.salvador@ossystems.com.br From: Thomas Thorne <Thomas.Thorne@Net2Edge.com> To: meta-freescale@yoctoproject.org Cc: Thomas.Thorne@Net2Edge.com, otavio.salvador@ossystems.com.br Subject: [Documentation][PATCH] Not Really - This is a hand made test Date: Wed, 21 Sep 2016 12:34:07 +0100 Message-Id: <1474457647-16977-1-git-send-email-Thomas.Thorne@Net2Edge.com> X-Mailer: git-send-email 2.7.4 Result: OK ----- Ahh I may have found something. When I check the syslog of my machine I can see a rejection message: ... Sep 21 11:56:04 thorne-ul-dt postfix/qmgr[5645]: 427121963DE6: from=<thomasthorne@thorne-ul-dt.transition.internal>, size=4069, nrcpt=2 (queue active) Sep 21 11:56:04 thorne-ul-dt postfix/qmgr[5645]: D45561963DE4: from=<thomasthorne@thorne-ul-dt.transition.internal>, size=3214, nrcpt=2 (queue active) Sep 21 11:56:04 thorne-ul-dt postfix/qmgr[5645]: 6FC201963DE1: from=<thomasthorne@thorne-ul-dt.transition.internal>, size=2085, nrcpt=2 (queue active) Sep 21 11:56:06 thorne-ul-dt postfix/smtp[12052]: 6FC201963DE1: to=<meta-freescale@yoctoproject.org>, relay=yocto-www.yoctoproject.org[140.211.169.56]:25, delay=92753, delays=92751/0.03/1.2/0.2, dsn=4.1.8, status=deferred (host yocto-www.yoctoproject.org[140.211.169.56] said: 450 4.1.8 <thomasthorne@thorne-ul-dt.transition.internal>: Sender address rejected: Domain not found (in reply to RCPT TO command)) Sep 21 11:56:06 thorne-ul-dt postfix/smtp[12050]: 427121963DE6: to=<meta-freescale@yoctoproject.org>, relay=yocto-www.yoctoproject.org[140.211.169.56]:25, delay=92726, delays=92724/0.01/1.2/0.2, dsn=4.1.8, status=deferred (host yocto-www.yoctoproject.org[140.211.169.56] said: 450 4.1.8 <thomasthorne@thorne-ul-dt.transition.internal>: Sender address rejected: Domain not found (in reply to RCPT TO command)) Sep 21 11:56:06 thorne-ul-dt postfix/smtp[12051]: D45561963DE4: to=<meta-freescale@yoctoproject.org>, relay=yocto-www.yoctoproject.org[140.211.169.56]:25, delay=92736, delays=92735/0.02/1.2/0.2, dsn=4.1.8, status=deferred (host yocto-www.yoctoproject.org[140.211.169.56] said: 450 4.1.8 <thomasthorne@thorne-ul-dt.transition.internal>: Sender address rejected: Domain not found (in reply to RCPT TO command)) ... Sep 21 12:34:16 thorne-ul-dt postfix/pickup[15440]: B4D4C1962505: uid=1000 from=<thomasthorne> Sep 21 12:34:16 thorne-ul-dt postfix/cleanup[17019]: B4D4C1962505: message-id=<1474457647-16977-1-git-send-email-Thomas.Thorne@Net2Edge.com> Sep 21 12:34:16 thorne-ul-dt postfix/qmgr[5645]: B4D4C1962505: from=<thomasthorne@thorne-ul-dt.transition.internal>, size=1184, nrcpt=3 (queue active) Sep 21 12:34:18 thorne-ul-dt postfix/smtp[17022]: B4D4C1962505: to=<otavio.salvador@ossystems.com.br>, relay=aspmx.l.google.com[173.194.200.26]:25, delay=1.5, delays=0.09/0.02/0.84/0.52, dsn=2.0.0, status=sent (250 2.0.0 OK 1474457658 i40si22363314otd.114 - gsmtp) Sep 21 12:34:18 thorne-ul-dt postfix/smtp[17023]: B4D4C1962505: to=<meta-freescale@yoctoproject.org>, relay=yocto-www.yoctoproject.org[140.211.169.56]:25, delay=1.6, delays=0.09/0.03/1.1/0.3, dsn=4.1.8, status=deferred (host yocto-www.yoctoproject.org[140.211.169.56] said: 450 4.1.8 <thomasthorne@thorne-ul-dt.transition.internal>: Sender address rejected: Domain not found (in reply to RCPT TO command)) Sep 21 12:34:18 thorne-ul-dt postfix/smtp[17021]: B4D4C1962505: to=<Thomas.Thorne@Net2Edge.com>, relay=net2edge-com.mail.protection.outlook.com[213.199.180.170]:25, delay=2.1, delays=0.09/0.01/0.77/1.2, dsn=2.6.0, status=sent (250 2.6.0 <1474457647-16977-1-git-send-email-Thomas.Thorne@Net2Edge.com> [InternalId=16557098934123, Hostname=DB6PR0701MB1880.eurprd07.prod.outlook.com] 7442 bytes in 0.174, 41.540 KB/sec Queued mail for delivery) ... Sep 21 12:41:04 thorne-ul-dt postfix/qmgr[5645]: B4D4C1962505: from=<thomasthorne@thorne-ul-dt.transition.internal>, size=1184, nrcpt=3 (queue active) Sep 21 12:41:04 thorne-ul-dt postfix/smtp[18315]: B4D4C1962505: to=<meta-freescale@yoctoproject.org>, relay=yocto-www.yoctoproject.org[140.211.169.56]:25, delay=408, delays=407/0.01/0.62/0.18, dsn=4.1.8, status=deferred (host yocto-www.yoctoproject.org[140.211.169.56] said: 450 4.1.8 <thomasthorne@thorne-ul-dt.transition.internal>: Sender address rejected: Domain not found (in reply to RCPT TO command)) ----- So it seems that by the time my email reaches the outside world it has been transformed into being "from=" my machine rather than from Exchange account. At this point the yocto server seems to reject the message. Does that look like the correct interpretation to you? I do not know if this is something I can easily amend or if I will need to talk with an IT guy. I can probably copy and paste the message into Thunderbird, which I know sends and received external emails. Does that sound like it may work? Alternativly I could email the patch to myself and forward it onward using either Outlook, Outlook web or Thunderbird. Thomas A. F. Thorne Software Engineer Net2Edge -----Original Message----- From: Otavio Salvador [mailto:otavio.salvador@ossystems.com.br] Sent: 21 September 2016 12:25 To: Thomas Thorne <Thomas.Thorne@net2edge.com>; Daiane Angolini <daiane.angolini@nxp.com> Cc: meta-freescale@yoctoproject.org Subject: Re: [meta-freescale] [<Documentation][PATCH] Update to Krogoth On Tue, Sep 20, 2016 at 6:15 AM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > There seem to be no further changes to the documentation repository so I have resent the old patches. I have copies of the 3 emails in my inbox as I CCed myself this time. All three patches that I submitted this morning start their subject line with "[Documentation][PATCH]" We did not receive them. I am adding Daiane on Cc so she can also keep an eye on this. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 11:51 ` Thomas Thorne @ 2016-09-21 12:03 ` Otavio Salvador 2016-09-21 12:26 ` Thomas A. F. Thorne MEng AUS MIET 0 siblings, 1 reply; 17+ messages in thread From: Otavio Salvador @ 2016-09-21 12:03 UTC (permalink / raw) To: Thomas Thorne; +Cc: meta-freescale On Wed, Sep 21, 2016 at 8:51 AM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > I have attempted to test if it is my client failing to send or my mail server refusing to deliver outside. To do so I hand edited one of my patch files into a new email and used the same git command to send the message. I received a copy of the email almost instantly in Outlook, which is running on another machine. I am confident that a message made it at least as far as the Exchange server for my office. ... It seems your e-mail is not right. Please send the patches attached so we can review them but would be great if you could talk to your admin people so your email settings could be fixed. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 12:03 ` Otavio Salvador @ 2016-09-21 12:26 ` Thomas A. F. Thorne MEng AUS MIET 2016-09-21 15:46 ` Daiane Angolini 0 siblings, 1 reply; 17+ messages in thread From: Thomas A. F. Thorne MEng AUS MIET @ 2016-09-21 12:26 UTC (permalink / raw) To: Otavio Salvador; +Cc: meta-freescale [-- Attachment #1.1.1: Type: text/plain, Size: 1020 bytes --] The three patches are attached: 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch 0001-Update-to-Krogoth.patch Thomas Thorne Software Engineer Net2Edge Limited On 21/09/16 13:03, Otavio Salvador wrote: > On Wed, Sep 21, 2016 at 8:51 AM, Thomas Thorne > <Thomas.Thorne@net2edge.com> wrote: >> I have attempted to test if it is my client failing to send or my mail server refusing to deliver outside. To do so I hand edited one of my patch files into a new email and used the same git command to send the message. I received a copy of the email almost instantly in Outlook, which is running on another machine. I am confident that a message made it at least as far as the Exchange server for my office. > ... > > It seems your e-mail is not right. Please send the patches attached so > we can review them but would be great if you could talk to your admin > people so your email settings could be fixed. > > > [-- Warning: decoded text below may be mangled, UTF-8 assumed --] [-- Attachment #1.1.2: 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch --] [-- Type: text/x-patch; name="0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch", Size: 1861 bytes --] From 34491be8b5358c636b5cdc225bba8b53f4894cdb Mon Sep 17 00:00:00 2001 From: Thomas Thorne <Thomas.Thorne@Net2Edge.com> Date: Wed, 31 Aug 2016 15:48:57 +0100 Subject: [Documentation][PATCH] Add Freescale LS1021A Tower System to machine-list.inc MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The Freescale QorIQ® LS1021A Tower® System Module is a supported platform listed as a supported machine when sourcing the ./setup- environment file. According to the details in the meta-fsl- arm/conf/machine/ls1021atwr.conf this is a ls102xa SoC item is supplied by the meta-fsl-arm layer. Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com> --- user-guide/source/machine-list.inc | 1 + 1 file changed, 1 insertion(+) diff --git a/user-guide/source/machine-list.inc b/user-guide/source/machine-list.inc index 885e4e8..36349e1 100644 --- a/user-guide/source/machine-list.inc +++ b/user-guide/source/machine-list.inc @@ -28,6 +28,7 @@ imx6qsabresd Freescale i.MX6Q SABRE Smart Device i imx6slevk Freescale i.MX6SL Evaluation Kit i.MX6SL meta-fsl-arm imx6solosabreauto Freescale i.MX6Solo SABRE Automotive i.MX6S meta-fsl-arm imx6solosabresd Freescale i.MX6Solo SABRE Smart Device i.MX6S meta-fsl-arm +ls1021atwr Freescale QorIQ® LS1021A Tower® System Module ls102xa meta-fsl-arm twr-vf65gs10 Freescale Vybrid TWR-VF65GS10 vf60 meta-fsl-arm imx233-olinuxino-maxi OLIMEX iMX233-OLinuXino-Maxi i.MX23 meta-fsl-arm-extra imx233-olinuxino-micro OLIMEX iMX233-OLinuXino-Micro i.MX23 meta-fsl-arm-extra -- 2.7.4 [-- Warning: decoded text below may be mangled, UTF-8 assumed --] [-- Attachment #1.1.3: 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch --] [-- Type: text/x-patch; name="0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch", Size: 3845 bytes --] From d8929f519f69412af110807e863c0c5b64216006 Mon Sep 17 00:00:00 2001 From: Thomas Thorne <Thomas.Thorne@Net2Edge.com> Date: Wed, 31 Aug 2016 15:22:44 +0100 Subject: [Documentation][PATCH] Include rootfs.tar.gz Method In Build and boot steps Many Yocto build systems, including the one for the ls1021a-twr do not generate .sdcard bianry images. This changeset adds some instructions on inflaiting a tar'ed and gzip'ed root filesystem image onto an SD card and then copying over the kernel and device tree bianry files too. I think this also reflects the more recent documentation from the Yocto project. Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com> --- user-guide/source/nsteps.rst | 52 +++++++++++++++++++++++++++++++++----------- 1 file changed, 39 insertions(+), 13 deletions(-) diff --git a/user-guide/source/nsteps.rst b/user-guide/source/nsteps.rst index a64cca7..63b2f6b 100644 --- a/user-guide/source/nsteps.rst +++ b/user-guide/source/nsteps.rst @@ -29,19 +29,45 @@ Build and boot in *N*-steps build $ bitbake-layers show-recipes "*image*" | grep ':' # To list all possible images build $ bitbake <selected image> # Bake! The first time can take several hours -6. Flash your SD card:: - - # Insert your SD Card - # Type '$ dmesg | tail' to see the device node being used, e.g /dev/sdb - # In case the SD to be flashed has already some partitions, the host system may have - # mounted these, so unmount them, e.g. '$ sudo umount /dev/sdb?'. - build $ ls -la 'tmp/deploy/images/<selected machine>/*.sdcard' - - # Flash the soft link one - build $ sudo dd if=tmp/deploy/images/<selected machine>/<selected image>-<selected machine>.sdcard \ - of=/dev/sdX \ - bs=1M \ - conv=fsync +6. Flash your SD card: + + a) With a pre-formed sdcard image:: + + # Insert your SD Card + # Type '$ dmesg | tail' to see the device node being used, e.g /dev/sdb + # In case the SD to be flashed has already some partitions, the host system may have + # mounted these, so unmount them, e.g. '$ sudo umount /dev/sdb?'. + build $ ls -la 'tmp/deploy/images/<selected machine>/*.sdcard' + + # Flash the soft link .sdcard image + build $ sudo dd \ + if=tmp/deploy/images/<selected machine>/<selected image>-<selected machine>.sdcard \ + of=/dev/sdX \ + bs=1M \ + conv=fsync + + b) With a pre-formed root filesystem archive, kernel and device tree binary image:: + + # Insert your SD Card + # Check your card is mounted ls /media/<user name>/<mounted filesystem name> + build $ ls -la 'tmp/deploy/images/<selected machine>/*.tar.gz' + + # Inflate the the soft link .tar.gz onto the cards filesystem + build $ sudo tar -zxvf \ + tmp/deploy/images/<selected machine>/<selected image>-<selected machine>.tar.gz \ + -C /media/<user name>/<mounted filesystem name> + + # Copy over the kernel + build $ ls -la 'tmp/deploy/images/<selected machine>/uImage*.bin' + build $ sudo cp \ + 'tmp/deploy/images/<selected machine>/uImage-<selected machine>.bin' \ + /media/<user name>/<mounted filesystem name>/boot/ + + # Copy over the device tree binary + build $ ls -la 'tmp/deploy/images/<selected machine>/uImage*.dtb' + build $ sudo cp \ + 'tmp/deploy/images/<selected machine>/uImage-<selected machine>.dtb' \ + /media/<user name>/<mounted filesystem name>/boot/ 7. Place your SD Card in the correct board's slot and boot! -- 2.7.4 [-- Warning: decoded text below may be mangled, UTF-8 assumed --] [-- Attachment #1.1.4: 0001-Update-to-Krogoth.patch --] [-- Type: text/x-patch; name="0001-Update-to-Krogoth.patch", Size: 2988 bytes --] From af9868ca98c638e9de2c1dfa368893593c454bda Mon Sep 17 00:00:00 2001 From: Thomas Thorne <Thomas.Thorne@Net2Edge.com> Date: Wed, 24 Aug 2016 17:54:59 +0100 Subject: [Documentation][PATCH] Update to Krogoth Replace 'Jethro' with 'Krogoth' and '2.0' with '2.1' Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com> --- FAQ/source/conf.py | 6 +++--- release-notes/source/conf.py | 2 +- user-guide/source/conf.py | 6 +++--- user-guide/source/nsteps.rst | 2 +- 4 files changed, 8 insertions(+), 8 deletions(-) diff --git a/FAQ/source/conf.py b/FAQ/source/conf.py index a2792a6..00eaebd 100644 --- a/FAQ/source/conf.py +++ b/FAQ/source/conf.py @@ -47,10 +47,10 @@ copyright = u'2014, Freescale Community BSP Team' # |version| and |release|, also used in various other places throughout the # built documents. # -# The short X.Y version. -version = '1.5' +# The short X.Y version or version name if applicable. +version = 'krogoth' # The full version, including alpha/beta/rc tags. -release = '1.5' +release = '2.1' # The language for content autogenerated by Sphinx. Refer to documentation # for a list of supported languages. diff --git a/release-notes/source/conf.py b/release-notes/source/conf.py index 6115217..0ea97f1 100644 --- a/release-notes/source/conf.py +++ b/release-notes/source/conf.py @@ -50,7 +50,7 @@ copyright = u'2013-2016, FSL Community BSP Team' # |version| and |release|, also used in various other places throughout the # built documents. # -# The short X.Y version. +# The short X.Y version or version name if applicable. version = 'krogoth' # The full version, including alpha/beta/rc tags. release = '2.1' diff --git a/user-guide/source/conf.py b/user-guide/source/conf.py index 558f919..7c9f536 100644 --- a/user-guide/source/conf.py +++ b/user-guide/source/conf.py @@ -47,10 +47,10 @@ copyright = u'2014, Freescale Community BSP Team' # |version| and |release|, also used in various other places throughout the # built documents. # -# The short X.Y version. -version = '1.6' +# The short X.Y version or version name if applicable. +version = 'krogoth' # The full version, including alpha/beta/rc tags. -release = '1.6' +release = '2.1' # The language for content autogenerated by Sphinx. Refer to documentation # for a list of supported languages. diff --git a/user-guide/source/nsteps.rst b/user-guide/source/nsteps.rst index df1c107..a64cca7 100644 --- a/user-guide/source/nsteps.rst +++ b/user-guide/source/nsteps.rst @@ -16,7 +16,7 @@ Build and boot in *N*-steps $ cd fsl-community-bsp fsl-community-bsp $ repo init \ -u https://github.com/Freescale/fsl-community-bsp-platform \ - -b jethro + -b krogoth fsl-community-bsp $ repo sync 4. Select your machine (:ref:`machines`) and prepare the environment for bitbake:: -- 2.7.4 [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 484 bytes --] ^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 12:26 ` Thomas A. F. Thorne MEng AUS MIET @ 2016-09-21 15:46 ` Daiane Angolini 2016-09-21 16:06 ` Thomas Thorne 0 siblings, 1 reply; 17+ messages in thread From: Daiane Angolini @ 2016-09-21 15:46 UTC (permalink / raw) To: Thomas.Thorne; +Cc: meta-freescale, Otavio Salvador On Wed, Sep 21, 2016 at 9:26 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: > The three patches are attached: > > 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch > > 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch > > 0001-Update-to-Krogoth.patch Let me review your patches and provide feedback. An alternative way to send patches would be using pull request on github. Daiane > > Thomas Thorne Software Engineer Net2Edge Limited > > On 21/09/16 13:03, Otavio Salvador wrote: >> On Wed, Sep 21, 2016 at 8:51 AM, Thomas Thorne >> <Thomas.Thorne@net2edge.com> wrote: >>> I have attempted to test if it is my client failing to send or my mail server refusing to deliver outside. To do so I hand edited one of my patch files into a new email and used the same git command to send the message. I received a copy of the email almost instantly in Outlook, which is running on another machine. I am confident that a message made it at least as far as the Exchange server for my office. >> ... >> >> It seems your e-mail is not right. Please send the patches attached so >> we can review them but would be great if you could talk to your admin >> people so your email settings could be fixed. >> >> >> > > > -- > _______________________________________________ > meta-freescale mailing list > meta-freescale@yoctoproject.org > https://lists.yoctoproject.org/listinfo/meta-freescale > ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 15:46 ` Daiane Angolini @ 2016-09-21 16:06 ` Thomas Thorne 2016-09-21 16:40 ` Daiane Angolini 0 siblings, 1 reply; 17+ messages in thread From: Thomas Thorne @ 2016-09-21 16:06 UTC (permalink / raw) To: Daiane Angolini; +Cc: meta-freescale, Otavio Salvador I can generate pull requests on GitHub for future document patches if that will make things easier. I will also try and follow up with the Exchange administrators about correcting our strange configuration. Thomas A. F. Thorne Software Engineer Net2Edge -----Original Message----- From: angolini@gmail.com [mailto:angolini@gmail.com] On Behalf Of Daiane Angolini Sent: 21 September 2016 16:47 To: Thomas Thorne <Thomas.Thorne@net2edge.com> Cc: Otavio Salvador <otavio.salvador@ossystems.com.br>; meta-freescale@yoctoproject.org Subject: Re: [meta-freescale] [<Documentation][PATCH] Update to Krogoth On Wed, Sep 21, 2016 at 9:26 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: > The three patches are attached: > > 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch > > 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch > > 0001-Update-to-Krogoth.patch Let me review your patches and provide feedback. An alternative way to send patches would be using pull request on github. Daiane > > Thomas Thorne Software Engineer Net2Edge Limited > > On 21/09/16 13:03, Otavio Salvador wrote: >> On Wed, Sep 21, 2016 at 8:51 AM, Thomas Thorne >> <Thomas.Thorne@net2edge.com> wrote: >>> I have attempted to test if it is my client failing to send or my mail server refusing to deliver outside. To do so I hand edited one of my patch files into a new email and used the same git command to send the message. I received a copy of the email almost instantly in Outlook, which is running on another machine. I am confident that a message made it at least as far as the Exchange server for my office. >> ... >> >> It seems your e-mail is not right. Please send the patches attached >> so we can review them but would be great if you could talk to your >> admin people so your email settings could be fixed. >> >> >> > > > -- > _______________________________________________ > meta-freescale mailing list > meta-freescale@yoctoproject.org > https://lists.yoctoproject.org/listinfo/meta-freescale > ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 16:06 ` Thomas Thorne @ 2016-09-21 16:40 ` Daiane Angolini 2016-09-21 16:45 ` Thomas Thorne 2016-09-22 13:55 ` Thomas A. F. Thorne MEng AUS MIET 0 siblings, 2 replies; 17+ messages in thread From: Daiane Angolini @ 2016-09-21 16:40 UTC (permalink / raw) To: Thomas Thorne; +Cc: meta-freescale, Otavio Salvador On Wed, Sep 21, 2016 at 1:06 PM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > I can generate pull requests on GitHub for future document patches if that will make things easier. I will also try and follow up with the Exchange administrators about correcting our strange configuration. > Yes, please ask your administrator, if it's going to take too long, send the pull request with the changes. Have you rendered the User Guide? Have you faced any problem during this process? > Thomas A. F. Thorne Software Engineer Net2Edge > > -----Original Message----- > From: angolini@gmail.com [mailto:angolini@gmail.com] On Behalf Of Daiane Angolini > Sent: 21 September 2016 16:47 > To: Thomas Thorne <Thomas.Thorne@net2edge.com> > Cc: Otavio Salvador <otavio.salvador@ossystems.com.br>; meta-freescale@yoctoproject.org > Subject: Re: [meta-freescale] [<Documentation][PATCH] Update to Krogoth > > On Wed, Sep 21, 2016 at 9:26 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: >> The three patches are attached: >> >> 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch This patch adds only LS1021A-Tower to the table. Can you, please try to update that table using the same content we have in Release Notes? /code/yocto/master/sources/Documentation$ find -name *machine-list.inc ./user-guide/source/machine-list.inc ./release-notes/source/machine-list.inc I think only copying over the file would be enough. >> >> 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch I link this patch! Thanks for documenting this. I would only add a note saying the sdcard may not be partitioned, and which would be the expected partition table to your procedure (would it be 2 partitions, one for rootfs and one for kernel?) Another point, you don't copy any bootloader, would it be a problem? >> >> 0001-Update-to-Krogoth.patch > The only change needed on this patch would be the commit log saying 2.0 -> 2.1 and in fact the patch change a lot of older versions to 2.1. So I would only way in commit log the patch "upgrades the versions to 2.1" Daiane ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 16:40 ` Daiane Angolini @ 2016-09-21 16:45 ` Thomas Thorne 2016-09-22 13:55 ` Thomas A. F. Thorne MEng AUS MIET 1 sibling, 0 replies; 17+ messages in thread From: Thomas Thorne @ 2016-09-21 16:45 UTC (permalink / raw) To: Daiane Angolini; +Cc: meta-freescale, Otavio Salvador I did render all the guides. The only problem I can remember facing is that one of the suggested formats did not work for me. I think I did a PDF in letter size instead of A4 or something. make latexpdf -t a4twoside I think it was the a4twoside which did not work. That is suggested in the README file though. Thomas A. F. Thorne Software Engineer Net2Edge -----Original Message----- From: angolini@gmail.com [mailto:angolini@gmail.com] On Behalf Of Daiane Angolini Sent: 21 September 2016 17:40 To: Thomas Thorne <Thomas.Thorne@net2edge.com> Cc: Otavio Salvador <otavio.salvador@ossystems.com.br>; meta-freescale@yoctoproject.org Subject: Re: [meta-freescale] [<Documentation][PATCH] Update to Krogoth On Wed, Sep 21, 2016 at 1:06 PM, Thomas Thorne <Thomas.Thorne@net2edge.com> wrote: > I can generate pull requests on GitHub for future document patches if that will make things easier. I will also try and follow up with the Exchange administrators about correcting our strange configuration. > Yes, please ask your administrator, if it's going to take too long, send the pull request with the changes. Have you rendered the User Guide? Have you faced any problem during this process? > Thomas A. F. Thorne Software Engineer Net2Edge > > -----Original Message----- > From: angolini@gmail.com [mailto:angolini@gmail.com] On Behalf Of > Daiane Angolini > Sent: 21 September 2016 16:47 > To: Thomas Thorne <Thomas.Thorne@net2edge.com> > Cc: Otavio Salvador <otavio.salvador@ossystems.com.br>; > meta-freescale@yoctoproject.org > Subject: Re: [meta-freescale] [<Documentation][PATCH] Update to > Krogoth > > On Wed, Sep 21, 2016 at 9:26 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: >> The three patches are attached: >> >> 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch This patch adds only LS1021A-Tower to the table. Can you, please try to update that table using the same content we have in Release Notes? /code/yocto/master/sources/Documentation$ find -name *machine-list.inc ./user-guide/source/machine-list.inc ./release-notes/source/machine-list.inc I think only copying over the file would be enough. >> >> 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch I link this patch! Thanks for documenting this. I would only add a note saying the sdcard may not be partitioned, and which would be the expected partition table to your procedure (would it be 2 partitions, one for rootfs and one for kernel?) Another point, you don't copy any bootloader, would it be a problem? >> >> 0001-Update-to-Krogoth.patch > The only change needed on this patch would be the commit log saying 2.0 -> 2.1 and in fact the patch change a lot of older versions to 2.1. So I would only way in commit log the patch "upgrades the versions to 2.1" Daiane ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-21 16:40 ` Daiane Angolini 2016-09-21 16:45 ` Thomas Thorne @ 2016-09-22 13:55 ` Thomas A. F. Thorne MEng AUS MIET 2016-09-22 18:25 ` Daiane Angolini 1 sibling, 1 reply; 17+ messages in thread From: Thomas A. F. Thorne MEng AUS MIET @ 2016-09-22 13:55 UTC (permalink / raw) To: Daiane Angolini; +Cc: meta-freescale, Otavio Salvador [-- Attachment #1.1: Type: text/plain, Size: 1647 bytes --] On Wed, Sep 21, 2016 at 1:06 PM, Thomas Thorne > <Thomas.Thorne@net2edge.com> wrote: >> I can generate pull requests on GitHub for future document patches if that will make things easier. I will also try and follow up with the Exchange administrators about correcting our strange configuration. >> > Yes, please ask your administrator, if it's going to take too long, > send the pull request with the changes. I have tried to set the from field for my git work area using: $ git config sendemail.from Thomas.Thorne@Net2Edge.com As a test I re-sent the 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch $ git send-email --to meta-freescale@yoctoproject.org --cc Thomas.Thorne@Net2Edge.com --cc otavio.salvador@ossystems.com.br ../0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch I do not think this has improved things based on my syslog. I can also still see the Return-Path: field in the header is set to the internal domain. I will try again with the sendemail.envelopeSender also set, transmitting the 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch. If that does not work I will try setting the sendemail.smtpDomain and sending the 0001-Update-to-Krogoth.patch. Hopefully we can see if any of them reach the list. I will work on the suggested alterations to the patches now. Then I can either re-submit the updated versions as attachments or use the git-send-email command if it is working. I will still discuss with my administrators the blocking emails from being sent externally with anything other than an @Net2Edge.com from: field. Regards, Tom [-- Attachment #2: OpenPGP digital signature --] [-- Type: application/pgp-signature, Size: 484 bytes --] ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-22 13:55 ` Thomas A. F. Thorne MEng AUS MIET @ 2016-09-22 18:25 ` Daiane Angolini 2016-09-23 19:18 ` Daiane Angolini 0 siblings, 1 reply; 17+ messages in thread From: Daiane Angolini @ 2016-09-22 18:25 UTC (permalink / raw) To: Thomas Thorne; +Cc: meta-freescale, Otavio Salvador On Thu, Sep 22, 2016 at 10:55 AM, Thomas A. F. Thorne MEng AUS MIET <Thomas.Thorne@net2edge.com> wrote: > On Wed, Sep 21, 2016 at 1:06 PM, Thomas Thorne >> <Thomas.Thorne@net2edge.com> wrote: >>> I can generate pull requests on GitHub for future document patches if that will make things easier. I will also try and follow up with the Exchange administrators about correcting our strange configuration. >>> >> Yes, please ask your administrator, if it's going to take too long, >> send the pull request with the changes. > I have tried to set the from field for my git work area using: > $ git config sendemail.from Thomas.Thorne@Net2Edge.com > > As a test I re-sent the > 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch > $ git send-email --to meta-freescale@yoctoproject.org --cc > Thomas.Thorne@Net2Edge.com --cc otavio.salvador@ossystems.com.br > ../0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch > > I do not think this has improved things based on my syslog. I can also > still see the Return-Path: field in the header is set to the internal > domain. I will try again with the sendemail.envelopeSender also set, > transmitting the > 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch. If > that does not work I will try setting the sendemail.smtpDomain and > sending the 0001-Update-to-Krogoth.patch. Hopefully we can see if any > of them reach the list. > > > I will work on the suggested alterations to the patches now. Then I can > either re-submit the updated versions as attachments or use the > git-send-email command if it is working. Thanks. Daiane > > I will still discuss with my administrators the blocking emails from > being sent externally with anything other than an @Net2Edge.com from: > field. > > Regards, Tom > ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [<Documentation][PATCH] Update to Krogoth 2016-09-22 18:25 ` Daiane Angolini @ 2016-09-23 19:18 ` Daiane Angolini 0 siblings, 0 replies; 17+ messages in thread From: Daiane Angolini @ 2016-09-23 19:18 UTC (permalink / raw) To: Thomas Thorne; +Cc: meta-freescale, Otavio Salvador On Thu, Sep 22, 2016 at 3:25 PM, Daiane Angolini <daiane.list@gmail.com> wrote: > On Thu, Sep 22, 2016 at 10:55 AM, Thomas A. F. Thorne MEng AUS MIET > <Thomas.Thorne@net2edge.com> wrote: >> On Wed, Sep 21, 2016 at 1:06 PM, Thomas Thorne >>> <Thomas.Thorne@net2edge.com> wrote: >>>> I can generate pull requests on GitHub for future document patches if that will make things easier. I will also try and follow up with the Exchange administrators about correcting our strange configuration. >>>> >>> Yes, please ask your administrator, if it's going to take too long, >>> send the pull request with the changes. >> I have tried to set the from field for my git work area using: >> $ git config sendemail.from Thomas.Thorne@Net2Edge.com >> >> As a test I re-sent the >> 0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch >> $ git send-email --to meta-freescale@yoctoproject.org --cc >> Thomas.Thorne@Net2Edge.com --cc otavio.salvador@ossystems.com.br >> ../0001-Add-Freescale-LS1021A-Tower-System-to-machine-list.i.patch >> >> I do not think this has improved things based on my syslog. I can also >> still see the Return-Path: field in the header is set to the internal >> domain. I will try again with the sendemail.envelopeSender also set, >> transmitting the >> 0001-Include-rootfs.tar.gz-Method-In-Build-and-boot-steps.patch. If >> that does not work I will try setting the sendemail.smtpDomain and >> sending the 0001-Update-to-Krogoth.patch. Hopefully we can see if any >> of them reach the list. >> >> >> I will work on the suggested alterations to the patches now. Then I can >> either re-submit the updated versions as attachments or use the >> git-send-email command if it is working. Hi Thomas, Can you confirm if your patches here https://patchwork.openembedded.org/project/meta-freescale/patches/?submitter=12459 are the original or are those with changes already? Daiane > > Thanks. > > Daiane >> >> I will still discuss with my administrators the blocking emails from >> being sent externally with anything other than an @Net2Edge.com from: >> field. >> >> Regards, Tom >> ^ permalink raw reply [flat|nested] 17+ messages in thread
* [Documentation][PATCH] Update to Krogoth @ 2016-09-22 14:37 Thomas.Thorne 0 siblings, 0 replies; 17+ messages in thread From: Thomas.Thorne @ 2016-09-22 14:37 UTC (permalink / raw) To: meta-freescale; +Cc: otavio.salvador From: Thomas Thorne <Thomas.Thorne@Net2Edge.com> Replace 'Jethro' with 'Krogoth' and '2.0' with '2.1' Signed-off-by: Thomas Thorne <Thomas.Thorne@Net2Edge.com> --- FAQ/source/conf.py | 6 +++--- release-notes/source/conf.py | 2 +- user-guide/source/conf.py | 6 +++--- user-guide/source/nsteps.rst | 2 +- 4 files changed, 8 insertions(+), 8 deletions(-) diff --git a/FAQ/source/conf.py b/FAQ/source/conf.py index a2792a6..00eaebd 100644 --- a/FAQ/source/conf.py +++ b/FAQ/source/conf.py @@ -47,10 +47,10 @@ copyright = u'2014, Freescale Community BSP Team' # |version| and |release|, also used in various other places throughout the # built documents. # -# The short X.Y version. -version = '1.5' +# The short X.Y version or version name if applicable. +version = 'krogoth' # The full version, including alpha/beta/rc tags. -release = '1.5' +release = '2.1' # The language for content autogenerated by Sphinx. Refer to documentation # for a list of supported languages. diff --git a/release-notes/source/conf.py b/release-notes/source/conf.py index 6115217..0ea97f1 100644 --- a/release-notes/source/conf.py +++ b/release-notes/source/conf.py @@ -50,7 +50,7 @@ copyright = u'2013-2016, FSL Community BSP Team' # |version| and |release|, also used in various other places throughout the # built documents. # -# The short X.Y version. +# The short X.Y version or version name if applicable. version = 'krogoth' # The full version, including alpha/beta/rc tags. release = '2.1' diff --git a/user-guide/source/conf.py b/user-guide/source/conf.py index 558f919..7c9f536 100644 --- a/user-guide/source/conf.py +++ b/user-guide/source/conf.py @@ -47,10 +47,10 @@ copyright = u'2014, Freescale Community BSP Team' # |version| and |release|, also used in various other places throughout the # built documents. # -# The short X.Y version. -version = '1.6' +# The short X.Y version or version name if applicable. +version = 'krogoth' # The full version, including alpha/beta/rc tags. -release = '1.6' +release = '2.1' # The language for content autogenerated by Sphinx. Refer to documentation # for a list of supported languages. diff --git a/user-guide/source/nsteps.rst b/user-guide/source/nsteps.rst index df1c107..a64cca7 100644 --- a/user-guide/source/nsteps.rst +++ b/user-guide/source/nsteps.rst @@ -16,7 +16,7 @@ Build and boot in *N*-steps $ cd fsl-community-bsp fsl-community-bsp $ repo init \ -u https://github.com/Freescale/fsl-community-bsp-platform \ - -b jethro + -b krogoth fsl-community-bsp $ repo sync 4. Select your machine (:ref:`machines`) and prepare the environment for bitbake:: -- 2.7.4 ^ permalink raw reply related [flat|nested] 17+ messages in thread
end of thread, other threads:[~2016-09-23 19:18 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <1472057811-31302-1-git-send-email-Thomas.Thorne@Net2Edge.com>
2016-09-01 14:28 ` [<Documentation][PATCH] Update to Krogoth Thomas A. F. Thorne MEng AUS MIET
2016-09-01 18:29 ` Otavio Salvador
2016-09-08 18:40 ` Thomas Thorne
2016-09-08 19:00 ` Otavio Salvador
2016-09-20 9:15 ` Thomas Thorne
2016-09-21 11:24 ` Otavio Salvador
2016-09-21 11:51 ` Thomas Thorne
2016-09-21 12:03 ` Otavio Salvador
2016-09-21 12:26 ` Thomas A. F. Thorne MEng AUS MIET
2016-09-21 15:46 ` Daiane Angolini
2016-09-21 16:06 ` Thomas Thorne
2016-09-21 16:40 ` Daiane Angolini
2016-09-21 16:45 ` Thomas Thorne
2016-09-22 13:55 ` Thomas A. F. Thorne MEng AUS MIET
2016-09-22 18:25 ` Daiane Angolini
2016-09-23 19:18 ` Daiane Angolini
2016-09-22 14:37 [Documentation][PATCH] " Thomas.Thorne
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.