[PATCH 0/3] TQMa93xxLA support

[PATCH 0/3] TQMa93xxLA support

[Alexander Stein]

Hi,

this series adds initial support for TQMa93xxLA soldered on MBa93xxLA.
As the name indicates this is an i.MX93 based SBC board. The initial support
includes typical interfaces like UART, eMMC, I2C, Ethernet.
Support for USB, LVDS and PMIC is still pending, which require additional
patches.
Patch 1 adds the compatible to dt bindings
Patch 2 adds .dts[i] files for module and sbc board support
Patch 3 adds more i.MX93 drivers to arm64 defconfig

Best regards,
Alexander

Alexander Stein (2):
  arm64: dts: freescale: add initial device tree for MBa93xxLA SBC board
  arm64: defconfig: Enable i.MX93 devices

Markus Niebel (1):
  dt: bindings: add bindings for TQMa93xxLA SOM

 .../devicetree/bindings/arm/fsl.yaml          |  19 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx93-tqma9352-mba93xxla.dts    | 629 ++++++++++++++++++
 .../boot/dts/freescale/imx93-tqma9352.dtsi    | 213 ++++++
 arch/arm64/configs/defconfig                  |   4 +
 5 files changed, 866 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi

-- 
2.34.1

[PATCH 0/3] TQMa93xxLA support

[Alexander Stein]

Hi,

this series adds initial support for TQMa93xxLA soldered on MBa93xxLA.
As the name indicates this is an i.MX93 based SBC board. The initial support
includes typical interfaces like UART, eMMC, I2C, Ethernet.
Support for USB, LVDS and PMIC is still pending, which require additional
patches.
Patch 1 adds the compatible to dt bindings
Patch 2 adds .dts[i] files for module and sbc board support
Patch 3 adds more i.MX93 drivers to arm64 defconfig

Best regards,
Alexander

Alexander Stein (2):
  arm64: dts: freescale: add initial device tree for MBa93xxLA SBC board
  arm64: defconfig: Enable i.MX93 devices

Markus Niebel (1):
  dt: bindings: add bindings for TQMa93xxLA SOM

 .../devicetree/bindings/arm/fsl.yaml          |  19 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx93-tqma9352-mba93xxla.dts    | 629 ++++++++++++++++++
 .../boot/dts/freescale/imx93-tqma9352.dtsi    | 213 ++++++
 arch/arm64/configs/defconfig                  |   4 +
 5 files changed, 866 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Alexander Stein]

From: Markus Niebel <Markus.Niebel@ew.tq-group.com>

TQMa93xxLA is a SOM variant in the TQ-Systems GmbH TQMa93xx series using
NXP i.MX93 CPU on an LGA type board.
MBa93xxCA is a starterkit base board for TQMa93xxLA on an adapter board.

Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 .../devicetree/bindings/arm/fsl.yaml          | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 2510eaa8906dd..8048c7f6a299d 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1219,6 +1219,25 @@ properties:
               - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
           - const: fsl,imxrt1170
 
+      - description:
+          TQMa93xxLA and TQMa93xxCA are two series of feature compatible SOM
+          using NXP i.MX93 SOC in 11x11 mm package.
+          TQMa93xxLA is designed to be soldered on different carrier boards.
+          TQMa93xxCA is a compatible variant using board to board connectors.
+          All SOM and CPU variants use the same device tree hence only one
+          compatible is needed. Bootloader disables all features not present
+          in the assembled SOC.
+          MBa93xxCA mainboard can be used as starterkit for the SOM
+          soldered on an adapter board or for the connector variant
+          MBa93xxLA mainboard is a single board computer using the solderable
+          SOM variant
+        items:
+          - enum:
+              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM on MBa93xxCA
+              - tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on MBa93xxLA SBC
+          - const: tq,imx93-tqma9352        # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM
+          - const: fsl,imx93
+
       - description:
           Freescale Vybrid Platform Device Tree Bindings
 
-- 
2.34.1

[PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Alexander Stein]

From: Markus Niebel <Markus.Niebel@ew.tq-group.com>

TQMa93xxLA is a SOM variant in the TQ-Systems GmbH TQMa93xx series using
NXP i.MX93 CPU on an LGA type board.
MBa93xxCA is a starterkit base board for TQMa93xxLA on an adapter board.

Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 .../devicetree/bindings/arm/fsl.yaml          | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 2510eaa8906dd..8048c7f6a299d 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1219,6 +1219,25 @@ properties:
               - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
           - const: fsl,imxrt1170
 
+      - description:
+          TQMa93xxLA and TQMa93xxCA are two series of feature compatible SOM
+          using NXP i.MX93 SOC in 11x11 mm package.
+          TQMa93xxLA is designed to be soldered on different carrier boards.
+          TQMa93xxCA is a compatible variant using board to board connectors.
+          All SOM and CPU variants use the same device tree hence only one
+          compatible is needed. Bootloader disables all features not present
+          in the assembled SOC.
+          MBa93xxCA mainboard can be used as starterkit for the SOM
+          soldered on an adapter board or for the connector variant
+          MBa93xxLA mainboard is a single board computer using the solderable
+          SOM variant
+        items:
+          - enum:
+              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM on MBa93xxCA
+              - tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on MBa93xxLA SBC
+          - const: tq,imx93-tqma9352        # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM
+          - const: fsl,imx93
+
       - description:
           Freescale Vybrid Platform Device Tree Bindings
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/3] arm64: dts: freescale: add initial device tree for MBa93xxLA SBC board

[Alexander Stein]

This adds support for TQMa93xx module and MBa93xxLA SBC board.
TQMa93xx is a SOM using i.MX93 SOC. The SOM features PMIC, RAM, e-MMC and
some optional peripherals like SPI-NOR, RTC, EEPROM, gyroscope and
secure element.
TQMa93xxLA is a solder on type SOM and can be used directly on MBa93XXLA.
TQMa93xxCA is a feature compatible, socketable type SOM.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx93-tqma9352-mba93xxla.dts    | 629 ++++++++++++++++++
 .../boot/dts/freescale/imx93-tqma9352.dtsi    | 213 ++++++
 3 files changed, 843 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a750be13ace89..2d5e9f495a646 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -141,6 +141,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-iris-v2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
 
 imx8mm-venice-gw72xx-0x-imx219-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-imx219.dtbo
 imx8mm-venice-gw72xx-0x-rs232-rts-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs232-rts.dtbo
diff --git a/arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts b/arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
new file mode 100644
index 0000000000000..a98a6592ecd83
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
@@ -0,0 +1,629 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2022-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Markus Niebel
+ * Author: Alexander Stein
+ */
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include "imx93-tqma9352.dtsi"
+
+/{
+	model = "TQ-Systems i.MX93 TQMa93xxLA on MBa93xxLA SBC";
+	compatible = "tq,imx93-tqma9352-mba93xxla",
+		     "tq,imx93-tqma9352", "fsl,imx93";
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	aliases {
+		eeprom0 = &eeprom0;
+		rtc0 = &pcf85063;
+		rtc1 = &bbnsm_rtc;
+	};
+
+	backlight_lvds: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&tpm5 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_12v0>;
+		enable-gpios = <&expander2 2 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	dp_refclk: dp-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		switch-a {
+			label = "switcha";
+			linux,code = <BTN_0>;
+			gpios = <&expander0 6 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		switch-b {
+			label = "switchb";
+			linux,code = <BTN_1>;
+			gpios = <&expander0 7 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&expander2 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&expander2 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_MB";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_3v8: regulator-3v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V8";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/* TODO: this is supply for IOT module */
+		regulator-always-on;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_5V0_MB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&expander1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy_eqos>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy_eqos: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_eqos_phy>;
+			reset-gpios = <&expander1 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <50000>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+			interrupt-parent = <&gpio3>;
+			interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy_fec>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <5000000>;
+
+		ethphy_fec: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fec_phy>;
+			reset-gpios = <&expander1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <50000>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+			interrupt-parent = <&gpio3>;
+			interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&gpio1 {
+	expander-irq-hog {
+		gpio-hog;
+		gpios = <12 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "PEX_INT#";
+	};
+
+	rtc-irq-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "RTC_EVENT#";
+	};
+};
+
+&gpio3 {
+	ethphy-eqos-irq-hog {
+		gpio-hog;
+		gpios = <26 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "ENET0_IRQ#";
+	};
+
+	ethphy-fec-irq-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "ENET1_IRQ#";
+	};
+};
+
+&lpi2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+	pinctrl-1 = <&pinctrl_lpi2c3>;
+	status = "okay";
+
+	temperature-sensor@1c {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x1c>;
+	};
+
+	eeprom2: eeprom@54 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x54>;
+		pagesize = <16>;
+		vcc-supply = <&reg_3v3>;
+	};
+
+	expander0: gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pexp_irq>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3>;
+		gpio-line-names = "3V8_EN", "",
+				  "", "IOT_PWRKEY",
+				  "IOT_RESET", "IOT_W_DISABLE",
+				  "BUTTON_A#", "BUTTON_B#";
+
+		/*
+		 * Controls the IOT W_DISABLE pin which is low active
+		 * as disable signal but inverted as seen from the CPU.
+		 * The output-low states, the signal is
+		 * inactive, e.g. not disabled
+		 */
+		iot_wdisable_hog: iot-wdisable-hog {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "IOT_W_DISABLE";
+		};
+	};
+
+	expander1: gpio@71 {
+		compatible = "nxp,pca9538";
+		reg = <0x71>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		gpio-line-names = "ENET1_RESET#", "ENET2_RESET#",
+				  "USB_RESET#", "",
+				  "WLAN_PD#", "WLAN_W_DISABLE#",
+				  "WLAN_PERST#", "12V_EN";
+
+		/*
+		 * Controls the WiFi card PD pin which is low active
+		 * as power down signal. The output-low states, the signal
+		 * is inactive, e.g. not power down
+		 */
+		wlan-pd-hog {
+			gpio-hog;
+			gpios = <4 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "WLAN_PD#";
+		};
+
+		/*
+		 * Controls the WiFi card disable pin which is low active
+		 * as disable signal. The output-low states, the signal
+		 * is inactive, e.g. not disabled
+		 */
+		wlan-wdisable-hog {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "WLAN_W_DISABLE#";
+		};
+
+		/*
+		 * Controls the WiFi card reset pin which is low active
+		 * as reset signal. The output-low states, the signal
+		 * is inactive, e.g. not in reset
+		 */
+		wlan-perst-hog {
+			gpio-hog;
+			gpios = <6 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "WLAN_PERST#";
+		};
+	};
+
+	expander2: gpio@72 {
+		compatible = "nxp,pca9538";
+		reg = <0x72>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		gpio-line-names = "LCD_RESET#", "LCD_PWR_EN",
+				  "LCD_BL_EN", "DP_EN",
+				  "MIPI_CSI_EN", "MIPI_CSI_RST#",
+				  "USER_LED1", "USER_LED2";
+	};
+};
+
+&lpi2c5 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpi2c5>;
+	pinctrl-1 = <&pinctrl_lpi2c5>;
+	status = "okay";
+
+	dp_bridge: dp-bridge@f {
+		compatible = "toshiba,tc358767";
+		reg = <0x0f>;
+		reset-gpios = <&expander2 3 GPIO_ACTIVE_LOW>;
+		clock-names = "ref";
+		clocks = <&dp_refclk>;
+		toshiba,hpd-pin = <0>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				dp_dsi_in: endpoint {
+				};
+			};
+		};
+	};
+};
+
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&lpuart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+/* disabled per default, console for M33 */
+&lpuart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "disabled";
+};
+
+&lpuart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	status = "okay";
+};
+
+&lpuart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart8>;
+	status = "okay";
+};
+
+&pcf85063 {
+	/* RTC_EVENT# is connected on MBa93xxLA */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcf85063>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&tpm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm5>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2_hs>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_uhs>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_uhs>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	disable-wp;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET1_MDC__ENET_QOS_MDC		0x51e
+			MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO		0x4000051e
+			/* PD | FSEL_2 | DSE X6 */
+			MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0		0x57e
+			MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1		0x57e
+			MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2		0x57e
+			MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3		0x57e
+			/* PD | FSEL_3 | DSE X6 */
+			MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x5fe
+			MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x57e
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0		0x51e
+			MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1		0x51e
+			MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2		0x51e
+			MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3		0x51e
+			MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x51e
+			/* PD | FSEL_3 | DSE X3 */
+			MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x58e
+		>;
+	};
+
+	pinctrl_eqos_phy: eqosphygrp {
+		fsl,pins = <
+			MX93_PAD_CCM_CLKO1__GPIO3_IO26		0x1306
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET2_MDC__ENET1_MDC			0x51e
+			MX93_PAD_ENET2_MDIO__ENET1_MDIO			0x4000051e
+			/* PD | FSEL_2 | DSE X6 */
+			MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0		0x57e
+			MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1		0x57e
+			MX93_PAD_ENET2_RD2__ENET1_RGMII_RD2		0x57e
+			MX93_PAD_ENET2_RD3__ENET1_RGMII_RD3		0x57e
+			/* PD | FSEL_3 | DSE X6 */
+			MX93_PAD_ENET2_RXC__ENET1_RGMII_RXC		0x5fe
+			MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL	0x57e
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0		0x51e
+			MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1		0x51e
+			MX93_PAD_ENET2_TD2__ENET1_RGMII_TD2		0x51e
+			MX93_PAD_ENET2_TD3__ENET1_RGMII_TD3		0x51e
+			MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL	0x51e
+			/* PD | FSEL_3 | DSE X3 */
+			MX93_PAD_ENET2_TXC__ENET1_RGMII_TXC		0x58e
+		>;
+	};
+
+	pinctrl_fec_phy: fecphygrp {
+		fsl,pins = <
+			MX93_PAD_CCM_CLKO2__GPIO3_IO27		0x1306
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX93_PAD_PDM_BIT_STREAM0__CAN1_RX	0x139e
+			MX93_PAD_PDM_CLK__CAN1_TX		0x139e
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO25__CAN2_TX		0x139e
+			MX93_PAD_GPIO_IO27__CAN2_RX		0x139e
+		>;
+	};
+
+	pinctrl_lpi2c3: lpi2c3grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO28__LPI2C3_SDA		0x40000b9e
+			MX93_PAD_GPIO_IO29__LPI2C3_SCL		0x40000b9e
+		>;
+	};
+
+	pinctrl_lpi2c5: lpi2c5grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO22__LPI2C5_SDA		0x40000b9e
+			MX93_PAD_GPIO_IO23__LPI2C5_SCL		0x40000b9e
+		>;
+	};
+
+	pinctrl_pcf85063: pcf85063grp {
+		fsl,pins = <
+			MX93_PAD_SAI1_RXD0__GPIO1_IO14		0x1306
+		>;
+	};
+
+	pinctrl_pexp_irq: pexpirqgrp {
+		fsl,pins = <
+			MX93_PAD_SAI1_TXC__GPIO1_IO12		0x1306
+		>;
+	};
+
+	pinctrl_tpm5: tpm5grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO06__TPM5_CH0		0x57e
+		>;
+	};
+
+	pinctrl_typec: typecgrp {
+		fsl,pins = <
+			MX93_PAD_I2C2_SCL__GPIO1_IO02		0x1306
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX93_PAD_UART1_RXD__LPUART1_RX		0x31e
+			MX93_PAD_UART1_TXD__LPUART1_TX		0x31e
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX93_PAD_UART2_TXD__LPUART2_TX		0x31e
+			MX93_PAD_UART2_RXD__LPUART2_RX		0x31e
+			MX93_PAD_SAI1_TXD0__LPUART2_RTS_B	0x31e
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO14__LPUART3_TX		0x31e
+			MX93_PAD_GPIO_IO15__LPUART3_RX		0x31e
+		>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO04__LPUART6_TX		0x31e
+			MX93_PAD_GPIO_IO05__LPUART6_RX		0x31e
+		>;
+	};
+
+	pinctrl_uart8: uart8grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO12__LPUART8_TX		0x31e
+			MX93_PAD_GPIO_IO13__LPUART8_RX		0x31e
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
+		>;
+	};
+
+	pinctrl_usdhc2_hs: usdhc2hsgrp {
+		fsl,pins = <
+			/* HYS | PD | PU | FSEL_3 | DSE X5 */
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17be
+			/* HYS | PD | PU | FSEL_3 | DSE X4 */
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x139e
+			/* HYS | PD | PU | FSEL_3 | DSE X3 */
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x138e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x138e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x138e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x138e
+			/* PD | PU | FSEL_2 | DSE X3 */
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x50e
+		>;
+	};
+
+	pinctrl_usdhc2_uhs: usdhc2uhsgrp {
+		fsl,pins = <
+			/* HYS | PD | PU | FSEL_3 | DSE X6 */
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17fe
+			/* HYS | PD | PU | FSEL_3 | DSE X4 */
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x139e
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x139e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x139e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x139e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x139e
+			/* PD | PU | FSEL_2 | DSE X3 */
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x50e
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi b/arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi
new file mode 100644
index 0000000000000..2f2bb2c49f04c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2022 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Markus Niebel
+ */
+
+#include "imx93.dtsi"
+
+/{
+	model = "TQ-Systems i.MX93 TQMa93xxLA/TQMa93xxCA SOM";
+	compatible = "tq,imx93-tqma9352", "fsl,imx93";
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			alloc-ranges = <0 0x60000000 0 0x40000000>;
+			size = <0 0x10000000>;
+			linux,cma-default;
+		};
+	};
+
+	reg_v1v8: regulator-v1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/* SD2 RST# via PMIC SW_EN */
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_v3v3>;
+		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_v1v8>;
+};
+
+&flexspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi1>;
+	status = "okay";
+
+	flash0: flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		/*
+		 * no DQS, RXCLKSRC internal loop back, max 66 MHz
+		 * clk framework uses CLK_DIVIDER_ROUND_CLOSEST
+		 * selected value together with root from
+		 * IMX93_CLK_SYS_PLL_PFD1 @ 800.000.000 Hz helps to
+		 * respect the maximum value.
+		 */
+		spi-max-frequency = <62000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&gpio1 {
+	pmic-irq-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "PMIC_IRQ#";
+	};
+};
+
+&lpi2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	pinctrl-1 = <&pinctrl_lpi2c1>;
+	status = "okay";
+
+	se97_som: temperature-sensor@1b {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <7000>;
+	};
+
+	eeprom0: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_v3v3>;
+	};
+
+	eeprom1: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+		vcc-supply = <&reg_v3v3>;
+	};
+
+	/* protectable identification memory (part of M24C64-D @57) */
+	eeprom@5f {
+		compatible = "st,24c64", "atmel,24c64";
+		reg = <0x5f>;
+		size = <32>;
+		pagesize = <32>;
+		vcc-supply = <&reg_v3v3>;
+	};
+
+	imu@6a {
+		compatible = "st,ism330dhcx";
+		reg = <0x6a>;
+		vdd-supply = <&reg_v3v3>;
+		vddio-supply = <&reg_v3v3>;
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&wdog3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexspi1: flexspi1grp {
+		fsl,pins = <
+			MX93_PAD_SD3_CMD__FLEXSPI1_A_SS0_B	0x3fe
+			MX93_PAD_SD3_CLK__FLEXSPI1_A_SCLK	0x3fe
+			MX93_PAD_SD3_DATA0__FLEXSPI1_A_DATA00	0x3fe
+			MX93_PAD_SD3_DATA1__FLEXSPI1_A_DATA01	0x3fe
+			MX93_PAD_SD3_DATA2__FLEXSPI1_A_DATA02	0x3fe
+			MX93_PAD_SD3_DATA3__FLEXSPI1_A_DATA03	0x3fe
+		>;
+	};
+
+	pinctrl_lpi2c1: lpi2c1grp {
+		fsl,pins = <
+			MX93_PAD_I2C1_SCL__LPI2C1_SCL		0x40000b9e
+			MX93_PAD_I2C1_SDA__LPI2C1_SDA		0x40000b9e
+		>;
+	};
+
+	pinctrl_pca9451: pca9451grp {
+		fsl,pins = <
+			MX93_PAD_I2C2_SDA__GPIO1_IO03		0x1306
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX93_PAD_SD2_RESET_B__GPIO3_IO07	0x1306
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			/* HYS | PU | PD | FSEL_3 | X5 */
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17be
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x17be
+			/* HYS | PU | FSEL_3 | X5 */
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x13be
+			/* HYS | PU | FSEL_3 | X4 */
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x139e
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x139e
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x139e
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x139e
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x139e
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x139e
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x139e
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x139e
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX93_PAD_WDOG_ANY__WDOG1_WDOG_ANY	0x31e
+		>;
+	};
+};
-- 
2.34.1

[PATCH 2/3] arm64: dts: freescale: add initial device tree for MBa93xxLA SBC board

[Alexander Stein]

This adds support for TQMa93xx module and MBa93xxLA SBC board.
TQMa93xx is a SOM using i.MX93 SOC. The SOM features PMIC, RAM, e-MMC and
some optional peripherals like SPI-NOR, RTC, EEPROM, gyroscope and
secure element.
TQMa93xxLA is a solder on type SOM and can be used directly on MBa93XXLA.
TQMa93xxCA is a feature compatible, socketable type SOM.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx93-tqma9352-mba93xxla.dts    | 629 ++++++++++++++++++
 .../boot/dts/freescale/imx93-tqma9352.dtsi    | 213 ++++++
 3 files changed, 843 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a750be13ace89..2d5e9f495a646 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -141,6 +141,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-iris-v2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
 
 imx8mm-venice-gw72xx-0x-imx219-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-imx219.dtbo
 imx8mm-venice-gw72xx-0x-rs232-rts-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs232-rts.dtbo
diff --git a/arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts b/arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
new file mode 100644
index 0000000000000..a98a6592ecd83
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-tqma9352-mba93xxla.dts
@@ -0,0 +1,629 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2022-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Markus Niebel
+ * Author: Alexander Stein
+ */
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include "imx93-tqma9352.dtsi"
+
+/{
+	model = "TQ-Systems i.MX93 TQMa93xxLA on MBa93xxLA SBC";
+	compatible = "tq,imx93-tqma9352-mba93xxla",
+		     "tq,imx93-tqma9352", "fsl,imx93";
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	aliases {
+		eeprom0 = &eeprom0;
+		rtc0 = &pcf85063;
+		rtc1 = &bbnsm_rtc;
+	};
+
+	backlight_lvds: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&tpm5 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_12v0>;
+		enable-gpios = <&expander2 2 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	dp_refclk: dp-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		switch-a {
+			label = "switcha";
+			linux,code = <BTN_0>;
+			gpios = <&expander0 6 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		switch-b {
+			label = "switchb";
+			linux,code = <BTN_1>;
+			gpios = <&expander0 7 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&expander2 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&expander2 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_MB";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_3v8: regulator-3v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V8";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/* TODO: this is supply for IOT module */
+		regulator-always-on;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_5V0_MB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&expander1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy_eqos>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy_eqos: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_eqos_phy>;
+			reset-gpios = <&expander1 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <50000>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+			interrupt-parent = <&gpio3>;
+			interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy_fec>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <5000000>;
+
+		ethphy_fec: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fec_phy>;
+			reset-gpios = <&expander1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <50000>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+			interrupt-parent = <&gpio3>;
+			interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&gpio1 {
+	expander-irq-hog {
+		gpio-hog;
+		gpios = <12 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "PEX_INT#";
+	};
+
+	rtc-irq-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "RTC_EVENT#";
+	};
+};
+
+&gpio3 {
+	ethphy-eqos-irq-hog {
+		gpio-hog;
+		gpios = <26 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "ENET0_IRQ#";
+	};
+
+	ethphy-fec-irq-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "ENET1_IRQ#";
+	};
+};
+
+&lpi2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+	pinctrl-1 = <&pinctrl_lpi2c3>;
+	status = "okay";
+
+	temperature-sensor@1c {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x1c>;
+	};
+
+	eeprom2: eeprom@54 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x54>;
+		pagesize = <16>;
+		vcc-supply = <&reg_3v3>;
+	};
+
+	expander0: gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pexp_irq>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3>;
+		gpio-line-names = "3V8_EN", "",
+				  "", "IOT_PWRKEY",
+				  "IOT_RESET", "IOT_W_DISABLE",
+				  "BUTTON_A#", "BUTTON_B#";
+
+		/*
+		 * Controls the IOT W_DISABLE pin which is low active
+		 * as disable signal but inverted as seen from the CPU.
+		 * The output-low states, the signal is
+		 * inactive, e.g. not disabled
+		 */
+		iot_wdisable_hog: iot-wdisable-hog {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "IOT_W_DISABLE";
+		};
+	};
+
+	expander1: gpio@71 {
+		compatible = "nxp,pca9538";
+		reg = <0x71>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		gpio-line-names = "ENET1_RESET#", "ENET2_RESET#",
+				  "USB_RESET#", "",
+				  "WLAN_PD#", "WLAN_W_DISABLE#",
+				  "WLAN_PERST#", "12V_EN";
+
+		/*
+		 * Controls the WiFi card PD pin which is low active
+		 * as power down signal. The output-low states, the signal
+		 * is inactive, e.g. not power down
+		 */
+		wlan-pd-hog {
+			gpio-hog;
+			gpios = <4 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "WLAN_PD#";
+		};
+
+		/*
+		 * Controls the WiFi card disable pin which is low active
+		 * as disable signal. The output-low states, the signal
+		 * is inactive, e.g. not disabled
+		 */
+		wlan-wdisable-hog {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "WLAN_W_DISABLE#";
+		};
+
+		/*
+		 * Controls the WiFi card reset pin which is low active
+		 * as reset signal. The output-low states, the signal
+		 * is inactive, e.g. not in reset
+		 */
+		wlan-perst-hog {
+			gpio-hog;
+			gpios = <6 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "WLAN_PERST#";
+		};
+	};
+
+	expander2: gpio@72 {
+		compatible = "nxp,pca9538";
+		reg = <0x72>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		gpio-line-names = "LCD_RESET#", "LCD_PWR_EN",
+				  "LCD_BL_EN", "DP_EN",
+				  "MIPI_CSI_EN", "MIPI_CSI_RST#",
+				  "USER_LED1", "USER_LED2";
+	};
+};
+
+&lpi2c5 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpi2c5>;
+	pinctrl-1 = <&pinctrl_lpi2c5>;
+	status = "okay";
+
+	dp_bridge: dp-bridge@f {
+		compatible = "toshiba,tc358767";
+		reg = <0x0f>;
+		reset-gpios = <&expander2 3 GPIO_ACTIVE_LOW>;
+		clock-names = "ref";
+		clocks = <&dp_refclk>;
+		toshiba,hpd-pin = <0>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				dp_dsi_in: endpoint {
+				};
+			};
+		};
+	};
+};
+
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&lpuart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+/* disabled per default, console for M33 */
+&lpuart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "disabled";
+};
+
+&lpuart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	status = "okay";
+};
+
+&lpuart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart8>;
+	status = "okay";
+};
+
+&pcf85063 {
+	/* RTC_EVENT# is connected on MBa93xxLA */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcf85063>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&tpm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm5>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2_hs>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_uhs>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_uhs>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	disable-wp;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET1_MDC__ENET_QOS_MDC		0x51e
+			MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO		0x4000051e
+			/* PD | FSEL_2 | DSE X6 */
+			MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0		0x57e
+			MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1		0x57e
+			MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2		0x57e
+			MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3		0x57e
+			/* PD | FSEL_3 | DSE X6 */
+			MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x5fe
+			MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x57e
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0		0x51e
+			MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1		0x51e
+			MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2		0x51e
+			MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3		0x51e
+			MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x51e
+			/* PD | FSEL_3 | DSE X3 */
+			MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x58e
+		>;
+	};
+
+	pinctrl_eqos_phy: eqosphygrp {
+		fsl,pins = <
+			MX93_PAD_CCM_CLKO1__GPIO3_IO26		0x1306
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET2_MDC__ENET1_MDC			0x51e
+			MX93_PAD_ENET2_MDIO__ENET1_MDIO			0x4000051e
+			/* PD | FSEL_2 | DSE X6 */
+			MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0		0x57e
+			MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1		0x57e
+			MX93_PAD_ENET2_RD2__ENET1_RGMII_RD2		0x57e
+			MX93_PAD_ENET2_RD3__ENET1_RGMII_RD3		0x57e
+			/* PD | FSEL_3 | DSE X6 */
+			MX93_PAD_ENET2_RXC__ENET1_RGMII_RXC		0x5fe
+			MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL	0x57e
+			/* PD | FSEL_2 | DSE X4 */
+			MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0		0x51e
+			MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1		0x51e
+			MX93_PAD_ENET2_TD2__ENET1_RGMII_TD2		0x51e
+			MX93_PAD_ENET2_TD3__ENET1_RGMII_TD3		0x51e
+			MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL	0x51e
+			/* PD | FSEL_3 | DSE X3 */
+			MX93_PAD_ENET2_TXC__ENET1_RGMII_TXC		0x58e
+		>;
+	};
+
+	pinctrl_fec_phy: fecphygrp {
+		fsl,pins = <
+			MX93_PAD_CCM_CLKO2__GPIO3_IO27		0x1306
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX93_PAD_PDM_BIT_STREAM0__CAN1_RX	0x139e
+			MX93_PAD_PDM_CLK__CAN1_TX		0x139e
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO25__CAN2_TX		0x139e
+			MX93_PAD_GPIO_IO27__CAN2_RX		0x139e
+		>;
+	};
+
+	pinctrl_lpi2c3: lpi2c3grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO28__LPI2C3_SDA		0x40000b9e
+			MX93_PAD_GPIO_IO29__LPI2C3_SCL		0x40000b9e
+		>;
+	};
+
+	pinctrl_lpi2c5: lpi2c5grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO22__LPI2C5_SDA		0x40000b9e
+			MX93_PAD_GPIO_IO23__LPI2C5_SCL		0x40000b9e
+		>;
+	};
+
+	pinctrl_pcf85063: pcf85063grp {
+		fsl,pins = <
+			MX93_PAD_SAI1_RXD0__GPIO1_IO14		0x1306
+		>;
+	};
+
+	pinctrl_pexp_irq: pexpirqgrp {
+		fsl,pins = <
+			MX93_PAD_SAI1_TXC__GPIO1_IO12		0x1306
+		>;
+	};
+
+	pinctrl_tpm5: tpm5grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO06__TPM5_CH0		0x57e
+		>;
+	};
+
+	pinctrl_typec: typecgrp {
+		fsl,pins = <
+			MX93_PAD_I2C2_SCL__GPIO1_IO02		0x1306
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX93_PAD_UART1_RXD__LPUART1_RX		0x31e
+			MX93_PAD_UART1_TXD__LPUART1_TX		0x31e
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX93_PAD_UART2_TXD__LPUART2_TX		0x31e
+			MX93_PAD_UART2_RXD__LPUART2_RX		0x31e
+			MX93_PAD_SAI1_TXD0__LPUART2_RTS_B	0x31e
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO14__LPUART3_TX		0x31e
+			MX93_PAD_GPIO_IO15__LPUART3_RX		0x31e
+		>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO04__LPUART6_TX		0x31e
+			MX93_PAD_GPIO_IO05__LPUART6_RX		0x31e
+		>;
+	};
+
+	pinctrl_uart8: uart8grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO12__LPUART8_TX		0x31e
+			MX93_PAD_GPIO_IO13__LPUART8_RX		0x31e
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
+		>;
+	};
+
+	pinctrl_usdhc2_hs: usdhc2hsgrp {
+		fsl,pins = <
+			/* HYS | PD | PU | FSEL_3 | DSE X5 */
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17be
+			/* HYS | PD | PU | FSEL_3 | DSE X4 */
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x139e
+			/* HYS | PD | PU | FSEL_3 | DSE X3 */
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x138e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x138e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x138e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x138e
+			/* PD | PU | FSEL_2 | DSE X3 */
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x50e
+		>;
+	};
+
+	pinctrl_usdhc2_uhs: usdhc2uhsgrp {
+		fsl,pins = <
+			/* HYS | PD | PU | FSEL_3 | DSE X6 */
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17fe
+			/* HYS | PD | PU | FSEL_3 | DSE X4 */
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x139e
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x139e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x139e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x139e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x139e
+			/* PD | PU | FSEL_2 | DSE X3 */
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x50e
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi b/arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi
new file mode 100644
index 0000000000000..2f2bb2c49f04c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-tqma9352.dtsi
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2022 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Markus Niebel
+ */
+
+#include "imx93.dtsi"
+
+/{
+	model = "TQ-Systems i.MX93 TQMa93xxLA/TQMa93xxCA SOM";
+	compatible = "tq,imx93-tqma9352", "fsl,imx93";
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			alloc-ranges = <0 0x60000000 0 0x40000000>;
+			size = <0 0x10000000>;
+			linux,cma-default;
+		};
+	};
+
+	reg_v1v8: regulator-v1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/* SD2 RST# via PMIC SW_EN */
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_v3v3>;
+		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_v1v8>;
+};
+
+&flexspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi1>;
+	status = "okay";
+
+	flash0: flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		/*
+		 * no DQS, RXCLKSRC internal loop back, max 66 MHz
+		 * clk framework uses CLK_DIVIDER_ROUND_CLOSEST
+		 * selected value together with root from
+		 * IMX93_CLK_SYS_PLL_PFD1 @ 800.000.000 Hz helps to
+		 * respect the maximum value.
+		 */
+		spi-max-frequency = <62000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&gpio1 {
+	pmic-irq-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "PMIC_IRQ#";
+	};
+};
+
+&lpi2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	pinctrl-1 = <&pinctrl_lpi2c1>;
+	status = "okay";
+
+	se97_som: temperature-sensor@1b {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <7000>;
+	};
+
+	eeprom0: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_v3v3>;
+	};
+
+	eeprom1: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+		vcc-supply = <&reg_v3v3>;
+	};
+
+	/* protectable identification memory (part of M24C64-D @57) */
+	eeprom@5f {
+		compatible = "st,24c64", "atmel,24c64";
+		reg = <0x5f>;
+		size = <32>;
+		pagesize = <32>;
+		vcc-supply = <&reg_v3v3>;
+	};
+
+	imu@6a {
+		compatible = "st,ism330dhcx";
+		reg = <0x6a>;
+		vdd-supply = <&reg_v3v3>;
+		vddio-supply = <&reg_v3v3>;
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&wdog3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexspi1: flexspi1grp {
+		fsl,pins = <
+			MX93_PAD_SD3_CMD__FLEXSPI1_A_SS0_B	0x3fe
+			MX93_PAD_SD3_CLK__FLEXSPI1_A_SCLK	0x3fe
+			MX93_PAD_SD3_DATA0__FLEXSPI1_A_DATA00	0x3fe
+			MX93_PAD_SD3_DATA1__FLEXSPI1_A_DATA01	0x3fe
+			MX93_PAD_SD3_DATA2__FLEXSPI1_A_DATA02	0x3fe
+			MX93_PAD_SD3_DATA3__FLEXSPI1_A_DATA03	0x3fe
+		>;
+	};
+
+	pinctrl_lpi2c1: lpi2c1grp {
+		fsl,pins = <
+			MX93_PAD_I2C1_SCL__LPI2C1_SCL		0x40000b9e
+			MX93_PAD_I2C1_SDA__LPI2C1_SDA		0x40000b9e
+		>;
+	};
+
+	pinctrl_pca9451: pca9451grp {
+		fsl,pins = <
+			MX93_PAD_I2C2_SDA__GPIO1_IO03		0x1306
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX93_PAD_SD2_RESET_B__GPIO3_IO07	0x1306
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			/* HYS | PU | PD | FSEL_3 | X5 */
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17be
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x17be
+			/* HYS | PU | FSEL_3 | X5 */
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x13be
+			/* HYS | PU | FSEL_3 | X4 */
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x139e
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x139e
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x139e
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x139e
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x139e
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x139e
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x139e
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x139e
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX93_PAD_WDOG_ANY__WDOG1_WDOG_ANY	0x31e
+		>;
+	};
+};
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/3] arm64: defconfig: Enable i.MX93 devices

[Alexander Stein]

These drivers are used on i.MX93 based devices.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 arch/arm64/configs/defconfig | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 8d850be05835f..0c2ee173a8730 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -425,6 +425,7 @@ CONFIG_TOUCHSCREEN_GOODIX=m
 CONFIG_TOUCHSCREEN_ELAN=m
 CONFIG_TOUCHSCREEN_EDT_FT5X06=m
 CONFIG_INPUT_MISC=y
+CONFIG_INPUT_BBNSM_PWRKEY=m
 CONFIG_INPUT_PM8941_PWRKEY=y
 CONFIG_INPUT_PM8XXX_VIBRATOR=m
 CONFIG_INPUT_TPS65219_PWRBUTTON=m
@@ -674,6 +675,7 @@ CONFIG_SUNXI_WATCHDOG=m
 CONFIG_NPCM7XX_WATCHDOG=y
 CONFIG_IMX2_WDT=y
 CONFIG_IMX_SC_WDT=m
+CONFIG_IMX7ULP_WDT=m
 CONFIG_QCOM_WDT=m
 CONFIG_MESON_GXBB_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=m
@@ -1088,6 +1090,7 @@ CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_RTC_DRV_PM8XXX=m
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_SNVS=m
+CONFIG_RTC_DRV_BBNSM=m
 CONFIG_RTC_DRV_IMX_SC=m
 CONFIG_RTC_DRV_MT6397=m
 CONFIG_RTC_DRV_XGENE=y
@@ -1396,6 +1399,7 @@ CONFIG_ARM_SPE_PMU=m
 CONFIG_ARM_DMC620_PMU=m
 CONFIG_HISI_PMU=y
 CONFIG_NVMEM_IMX_OCOTP=y
+CONFIG_NVMEM_IMX_OCOTP_ELE=m
 CONFIG_NVMEM_IMX_OCOTP_SCU=y
 CONFIG_NVMEM_LAYERSCAPE_SFP=m
 CONFIG_NVMEM_MESON_EFUSE=m
-- 
2.34.1

[PATCH 3/3] arm64: defconfig: Enable i.MX93 devices

[Alexander Stein]

These drivers are used on i.MX93 based devices.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 arch/arm64/configs/defconfig | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 8d850be05835f..0c2ee173a8730 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -425,6 +425,7 @@ CONFIG_TOUCHSCREEN_GOODIX=m
 CONFIG_TOUCHSCREEN_ELAN=m
 CONFIG_TOUCHSCREEN_EDT_FT5X06=m
 CONFIG_INPUT_MISC=y
+CONFIG_INPUT_BBNSM_PWRKEY=m
 CONFIG_INPUT_PM8941_PWRKEY=y
 CONFIG_INPUT_PM8XXX_VIBRATOR=m
 CONFIG_INPUT_TPS65219_PWRBUTTON=m
@@ -674,6 +675,7 @@ CONFIG_SUNXI_WATCHDOG=m
 CONFIG_NPCM7XX_WATCHDOG=y
 CONFIG_IMX2_WDT=y
 CONFIG_IMX_SC_WDT=m
+CONFIG_IMX7ULP_WDT=m
 CONFIG_QCOM_WDT=m
 CONFIG_MESON_GXBB_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=m
@@ -1088,6 +1090,7 @@ CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_RTC_DRV_PM8XXX=m
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_SNVS=m
+CONFIG_RTC_DRV_BBNSM=m
 CONFIG_RTC_DRV_IMX_SC=m
 CONFIG_RTC_DRV_MT6397=m
 CONFIG_RTC_DRV_XGENE=y
@@ -1396,6 +1399,7 @@ CONFIG_ARM_SPE_PMU=m
 CONFIG_ARM_DMC620_PMU=m
 CONFIG_HISI_PMU=y
 CONFIG_NVMEM_IMX_OCOTP=y
+CONFIG_NVMEM_IMX_OCOTP_ELE=m
 CONFIG_NVMEM_IMX_OCOTP_SCU=y
 CONFIG_NVMEM_LAYERSCAPE_SFP=m
 CONFIG_NVMEM_MESON_EFUSE=m
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Krzysztof Kozlowski]

On 09/06/2023 15:29, Alexander Stein wrote:
> From: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> 
> TQMa93xxLA is a SOM variant in the TQ-Systems GmbH TQMa93xx series using
> NXP i.MX93 CPU on an LGA type board.
> MBa93xxCA is a starterkit base board for TQMa93xxLA on an adapter board.

Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.

It is dt-bindings, not something else.

A nit, subject: drop second/last, redundant "bindings for". The
"dt-bindings" prefix is already stating that these are bindings. One
bindings is enough.


> 
> Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
>  .../devicetree/bindings/arm/fsl.yaml          | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 2510eaa8906dd..8048c7f6a299d 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -1219,6 +1219,25 @@ properties:
>                - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
>            - const: fsl,imxrt1170
>  
> +      - description:
> +          TQMa93xxLA and TQMa93xxCA are two series of feature compatible SOM
> +          using NXP i.MX93 SOC in 11x11 mm package.
> +          TQMa93xxLA is designed to be soldered on different carrier boards.
> +          TQMa93xxCA is a compatible variant using board to board connectors.
> +          All SOM and CPU variants use the same device tree hence only one
> +          compatible is needed. Bootloader disables all features not present
> +          in the assembled SOC.
> +          MBa93xxCA mainboard can be used as starterkit for the SOM
> +          soldered on an adapter board or for the connector variant
> +          MBa93xxLA mainboard is a single board computer using the solderable
> +          SOM variant
> +        items:
> +          - enum:
> +              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM on MBa93xxCA
> +              - tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on MBa93xxLA SBC

xx sound like wildcard which you should not use. If you open the product
page, it also suggests that.

Best regards,
Krzysztof

Re: [PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Krzysztof Kozlowski]

On 09/06/2023 15:29, Alexander Stein wrote:
> From: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> 
> TQMa93xxLA is a SOM variant in the TQ-Systems GmbH TQMa93xx series using
> NXP i.MX93 CPU on an LGA type board.
> MBa93xxCA is a starterkit base board for TQMa93xxLA on an adapter board.

Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.

It is dt-bindings, not something else.

A nit, subject: drop second/last, redundant "bindings for". The
"dt-bindings" prefix is already stating that these are bindings. One
bindings is enough.


> 
> Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
>  .../devicetree/bindings/arm/fsl.yaml          | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 2510eaa8906dd..8048c7f6a299d 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -1219,6 +1219,25 @@ properties:
>                - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
>            - const: fsl,imxrt1170
>  
> +      - description:
> +          TQMa93xxLA and TQMa93xxCA are two series of feature compatible SOM
> +          using NXP i.MX93 SOC in 11x11 mm package.
> +          TQMa93xxLA is designed to be soldered on different carrier boards.
> +          TQMa93xxCA is a compatible variant using board to board connectors.
> +          All SOM and CPU variants use the same device tree hence only one
> +          compatible is needed. Bootloader disables all features not present
> +          in the assembled SOC.
> +          MBa93xxCA mainboard can be used as starterkit for the SOM
> +          soldered on an adapter board or for the connector variant
> +          MBa93xxLA mainboard is a single board computer using the solderable
> +          SOM variant
> +        items:
> +          - enum:
> +              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM on MBa93xxCA
> +              - tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on MBa93xxLA SBC

xx sound like wildcard which you should not use. If you open the product
page, it also suggests that.

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Alexander Stein]

Hi,

Am Freitag, 9. Juni 2023, 17:58:17 CEST schrieb Krzysztof Kozlowski:
> On 09/06/2023 15:29, Alexander Stein wrote:
> > From: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> > 
> > TQMa93xxLA is a SOM variant in the TQ-Systems GmbH TQMa93xx series using
> > NXP i.MX93 CPU on an LGA type board.
> > MBa93xxCA is a starterkit base board for TQMa93xxLA on an adapter board.
> 
> Please use subject prefixes matching the subsystem. You can get them for
> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
> your patch is touching.
> 
> It is dt-bindings, not something else.
> 
> A nit, subject: drop second/last, redundant "bindings for". The
> "dt-bindings" prefix is already stating that these are bindings. One
> bindings is enough.

Thanks. I'll update that.

> > Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> > Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> > ---
> > 
> >  .../devicetree/bindings/arm/fsl.yaml          | 19 +++++++++++++++++++
> >  1 file changed, 19 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml
> > b/Documentation/devicetree/bindings/arm/fsl.yaml index
> > 2510eaa8906dd..8048c7f6a299d 100644
> > --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> > +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> > 
> > @@ -1219,6 +1219,25 @@ properties:
> >                - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
> >            
> >            - const: fsl,imxrt1170
> > 
> > +      - description:
> > +          TQMa93xxLA and TQMa93xxCA are two series of feature compatible
> > SOM +          using NXP i.MX93 SOC in 11x11 mm package.
> > +          TQMa93xxLA is designed to be soldered on different carrier
> > boards. +          TQMa93xxCA is a compatible variant using board to
> > board connectors. +          All SOM and CPU variants use the same device
> > tree hence only one +          compatible is needed. Bootloader disables
> > all features not present +          in the assembled SOC.
> > +          MBa93xxCA mainboard can be used as starterkit for the SOM
> > +          soldered on an adapter board or for the connector variant
> > +          MBa93xxLA mainboard is a single board computer using the
> > solderable +          SOM variant
> > +        items:
> > +          - enum:
> > +              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93
> > TQMa93xxCA/LA SOM on MBa93xxCA +              -
> > tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on
> > MBa93xxLA SBC
> xx sound like wildcard which you should not use. If you open the product
> page, it also suggests that.

xx is a wildcard only for modules TQMa93xx, depending on the soldered SoC, but 
not for the mainboard MBa93xx.
You are right that there is the ordering number MBa9352LA-AA, so the 
compatible would be "tq,imx93-tqma9352-mba9352la". But the actual values for 
the wildcards is copied from the soldered module. So using a TQMa9351LA would 
result in MBa9351LA-AA, although the mainboard is identical.

Best regards,
Alexander

> Best regards,
> Krzysztof


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/

Re: [PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Alexander Stein]

Hi,

Am Freitag, 9. Juni 2023, 17:58:17 CEST schrieb Krzysztof Kozlowski:
> On 09/06/2023 15:29, Alexander Stein wrote:
> > From: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> > 
> > TQMa93xxLA is a SOM variant in the TQ-Systems GmbH TQMa93xx series using
> > NXP i.MX93 CPU on an LGA type board.
> > MBa93xxCA is a starterkit base board for TQMa93xxLA on an adapter board.
> 
> Please use subject prefixes matching the subsystem. You can get them for
> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
> your patch is touching.
> 
> It is dt-bindings, not something else.
> 
> A nit, subject: drop second/last, redundant "bindings for". The
> "dt-bindings" prefix is already stating that these are bindings. One
> bindings is enough.

Thanks. I'll update that.

> > Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> > Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> > ---
> > 
> >  .../devicetree/bindings/arm/fsl.yaml          | 19 +++++++++++++++++++
> >  1 file changed, 19 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml
> > b/Documentation/devicetree/bindings/arm/fsl.yaml index
> > 2510eaa8906dd..8048c7f6a299d 100644
> > --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> > +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> > 
> > @@ -1219,6 +1219,25 @@ properties:
> >                - fsl,imxrt1170-evk         # i.MXRT1170 EVK Board
> >            
> >            - const: fsl,imxrt1170
> > 
> > +      - description:
> > +          TQMa93xxLA and TQMa93xxCA are two series of feature compatible
> > SOM +          using NXP i.MX93 SOC in 11x11 mm package.
> > +          TQMa93xxLA is designed to be soldered on different carrier
> > boards. +          TQMa93xxCA is a compatible variant using board to
> > board connectors. +          All SOM and CPU variants use the same device
> > tree hence only one +          compatible is needed. Bootloader disables
> > all features not present +          in the assembled SOC.
> > +          MBa93xxCA mainboard can be used as starterkit for the SOM
> > +          soldered on an adapter board or for the connector variant
> > +          MBa93xxLA mainboard is a single board computer using the
> > solderable +          SOM variant
> > +        items:
> > +          - enum:
> > +              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93
> > TQMa93xxCA/LA SOM on MBa93xxCA +              -
> > tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on
> > MBa93xxLA SBC
> xx sound like wildcard which you should not use. If you open the product
> page, it also suggests that.

xx is a wildcard only for modules TQMa93xx, depending on the soldered SoC, but 
not for the mainboard MBa93xx.
You are right that there is the ordering number MBa9352LA-AA, so the 
compatible would be "tq,imx93-tqma9352-mba9352la". But the actual values for 
the wildcards is copied from the soldered module. So using a TQMa9351LA would 
result in MBa9351LA-AA, although the mainboard is identical.

Best regards,
Alexander

> Best regards,
> Krzysztof


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Krzysztof Kozlowski]

On 15/06/2023 16:46, Alexander Stein wrote:
>>> +          TQMa93xxLA and TQMa93xxCA are two series of feature compatible
>>> SOM +          using NXP i.MX93 SOC in 11x11 mm package.
>>> +          TQMa93xxLA is designed to be soldered on different carrier
>>> boards. +          TQMa93xxCA is a compatible variant using board to
>>> board connectors. +          All SOM and CPU variants use the same device
>>> tree hence only one +          compatible is needed. Bootloader disables
>>> all features not present +          in the assembled SOC.
>>> +          MBa93xxCA mainboard can be used as starterkit for the SOM
>>> +          soldered on an adapter board or for the connector variant
>>> +          MBa93xxLA mainboard is a single board computer using the
>>> solderable +          SOM variant
>>> +        items:
>>> +          - enum:
>>> +              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93
>>> TQMa93xxCA/LA SOM on MBa93xxCA +              -
>>> tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on
>>> MBa93xxLA SBC
>> xx sound like wildcard which you should not use. If you open the product
>> page, it also suggests that.
> 
> xx is a wildcard only for modules TQMa93xx, depending on the soldered SoC, but 
> not for the mainboard MBa93xx.
> You are right that there is the ordering number MBa9352LA-AA, so the 
> compatible would be "tq,imx93-tqma9352-mba9352la". But the actual values for 
> the wildcards is copied from the soldered module. So using a TQMa9351LA would 
> result in MBa9351LA-AA, although the mainboard is identical.

OK

Best regards,
Krzysztof

Re: [PATCH 1/3] dt: bindings: add bindings for TQMa93xxLA SOM

[Krzysztof Kozlowski]

On 15/06/2023 16:46, Alexander Stein wrote:
>>> +          TQMa93xxLA and TQMa93xxCA are two series of feature compatible
>>> SOM +          using NXP i.MX93 SOC in 11x11 mm package.
>>> +          TQMa93xxLA is designed to be soldered on different carrier
>>> boards. +          TQMa93xxCA is a compatible variant using board to
>>> board connectors. +          All SOM and CPU variants use the same device
>>> tree hence only one +          compatible is needed. Bootloader disables
>>> all features not present +          in the assembled SOC.
>>> +          MBa93xxCA mainboard can be used as starterkit for the SOM
>>> +          soldered on an adapter board or for the connector variant
>>> +          MBa93xxLA mainboard is a single board computer using the
>>> solderable +          SOM variant
>>> +        items:
>>> +          - enum:
>>> +              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93
>>> TQMa93xxCA/LA SOM on MBa93xxCA +              -
>>> tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on
>>> MBa93xxLA SBC
>> xx sound like wildcard which you should not use. If you open the product
>> page, it also suggests that.
> 
> xx is a wildcard only for modules TQMa93xx, depending on the soldered SoC, but 
> not for the mainboard MBa93xx.
> You are right that there is the ordering number MBa9352LA-AA, so the 
> compatible would be "tq,imx93-tqma9352-mba9352la". But the actual values for 
> the wildcards is copied from the soldered module. So using a TQMa9351LA would 
> result in MBa9351LA-AA, although the mainboard is identical.

OK

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel