* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node @ 2019-03-22 9:15 Ley Foon Tan 2019-03-22 10:51 ` Marek Vasut 2019-03-22 11:43 ` Simon Goldschmidt 0 siblings, 2 replies; 10+ messages in thread From: Ley Foon Tan @ 2019-03-22 9:15 UTC (permalink / raw) To: u-boot Add QSPI device tree to Stratix 10. Sync from Linux Stratix 10 dts. Tested on Stratix 10 SoC devkit. SOCFPGA_STRATIX10 # sf probe 0:0 SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> --- arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ 2 files changed, 36 insertions(+) diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi index ee93725d64..9998bb1ba3 100644 --- a/arch/arm/dts/socfpga_stratix10.dtsi +++ b/arch/arm/dts/socfpga_stratix10.dtsi @@ -391,5 +391,20 @@ resets = <&rst WATCHDOG3_RESET>; status = "disabled"; }; + + qspi: spi at ff8d2000 { + compatible = "cdns,qspi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff8d2000 0x100>, + <0xff900000 0x100000>; + interrupts = <0 3 4>; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + bus-num = <0>; + status = "disabled"; + u-boot,dm-pre-reloc; + }; }; }; diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts index c59b77d829..4c47415b51 100644 --- a/arch/arm/dts/socfpga_stratix10_socdk.dts +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts @@ -10,6 +10,7 @@ aliases { serial0 = &uart0; + spi0 = &qspi; }; chosen { @@ -87,6 +88,26 @@ smplsel = <0>; }; +&qspi { + status = "okay"; + + flash at 0 { + u-boot,dm-pre-reloc; + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash"; + reg = <0>; /* chip select */ + spi-max-frequency = <50000000>; + + page-size = <256>; + block-size = <16>; /* 2^16, 64KB */ + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; +}; + &uart0 { status = "okay"; }; -- 2.19.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 9:15 [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node Ley Foon Tan @ 2019-03-22 10:51 ` Marek Vasut 2019-03-22 12:06 ` Simon Goldschmidt 2019-03-22 11:43 ` Simon Goldschmidt 1 sibling, 1 reply; 10+ messages in thread From: Marek Vasut @ 2019-03-22 10:51 UTC (permalink / raw) To: u-boot On 3/22/19 10:15 AM, Ley Foon Tan wrote: > Add QSPI device tree to Stratix 10. > Sync from Linux Stratix 10 dts. > > Tested on Stratix 10 SoC devkit. > SOCFPGA_STRATIX10 # sf probe 0:0 > SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB > > Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > --- > arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > 2 files changed, 36 insertions(+) > > diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi > index ee93725d64..9998bb1ba3 100644 > --- a/arch/arm/dts/socfpga_stratix10.dtsi > +++ b/arch/arm/dts/socfpga_stratix10.dtsi > @@ -391,5 +391,20 @@ > resets = <&rst WATCHDOG3_RESET>; > status = "disabled"; > }; > + > + qspi: spi at ff8d2000 { > + compatible = "cdns,qspi-nor"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0xff8d2000 0x100>, > + <0xff900000 0x100000>; > + interrupts = <0 3 4>; > + cdns,fifo-depth = <128>; > + cdns,fifo-width = <4>; > + cdns,trigger-address = <0x00000000>; > + bus-num = <0>; > + status = "disabled"; > + u-boot,dm-pre-reloc; > + }; > }; > }; > diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts > index c59b77d829..4c47415b51 100644 > --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > @@ -10,6 +10,7 @@ > > aliases { > serial0 = &uart0; > + spi0 = &qspi; > }; > > chosen { > @@ -87,6 +88,26 @@ > smplsel = <0>; > }; > > +&qspi { > + status = "okay"; > + > + flash at 0 { > + u-boot,dm-pre-reloc; > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "spi-flash"; > + reg = <0>; /* chip select */ > + spi-max-frequency = <50000000>; The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 MHz ? > + page-size = <256>; > + block-size = <16>; /* 2^16, 64KB */ > + cdns,tshsl-ns = <50>; > + cdns,tsd2d-ns = <50>; > + cdns,tchsh-ns = <4>; > + cdns,tslch-ns = <4>; > + }; > +}; > + > &uart0 { > status = "okay"; > }; > -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 10:51 ` Marek Vasut @ 2019-03-22 12:06 ` Simon Goldschmidt 2019-03-22 12:09 ` Marek Vasut 0 siblings, 1 reply; 10+ messages in thread From: Simon Goldschmidt @ 2019-03-22 12:06 UTC (permalink / raw) To: u-boot On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: > > On 3/22/19 10:15 AM, Ley Foon Tan wrote: > > Add QSPI device tree to Stratix 10. > > Sync from Linux Stratix 10 dts. > > > > Tested on Stratix 10 SoC devkit. > > SOCFPGA_STRATIX10 # sf probe 0:0 > > SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB > > > > Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > > --- > > arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > > arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > > 2 files changed, 36 insertions(+) > > > > diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi > > index ee93725d64..9998bb1ba3 100644 > > --- a/arch/arm/dts/socfpga_stratix10.dtsi > > +++ b/arch/arm/dts/socfpga_stratix10.dtsi > > @@ -391,5 +391,20 @@ > > resets = <&rst WATCHDOG3_RESET>; > > status = "disabled"; > > }; > > + > > + qspi: spi at ff8d2000 { > > + compatible = "cdns,qspi-nor"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0xff8d2000 0x100>, > > + <0xff900000 0x100000>; > > + interrupts = <0 3 4>; > > + cdns,fifo-depth = <128>; > > + cdns,fifo-width = <4>; > > + cdns,trigger-address = <0x00000000>; > > + bus-num = <0>; > > + status = "disabled"; > > + u-boot,dm-pre-reloc; > > + }; > > }; > > }; > > diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts > > index c59b77d829..4c47415b51 100644 > > --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > > +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > > @@ -10,6 +10,7 @@ > > > > aliases { > > serial0 = &uart0; > > + spi0 = &qspi; > > }; > > > > chosen { > > @@ -87,6 +88,26 @@ > > smplsel = <0>; > > }; > > > > +&qspi { > > + status = "okay"; > > + > > + flash at 0 { > > + u-boot,dm-pre-reloc; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + compatible = "spi-flash"; > > + reg = <0>; /* chip select */ > > + spi-max-frequency = <50000000>; > > The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 MHz ? I wonder who, when and why they were switched to 100 MHz, as they were at 50 MHz in the past as well, or am I wrong? Regards, Simon > > > + page-size = <256>; > > + block-size = <16>; /* 2^16, 64KB */ > > + cdns,tshsl-ns = <50>; > > + cdns,tsd2d-ns = <50>; > > + cdns,tchsh-ns = <4>; > > + cdns,tslch-ns = <4>; > > + }; > > +}; > > + > > &uart0 { > > status = "okay"; > > }; > > > > > -- > Best regards, > Marek Vasut ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 12:06 ` Simon Goldschmidt @ 2019-03-22 12:09 ` Marek Vasut 2019-03-22 12:18 ` Simon Goldschmidt 0 siblings, 1 reply; 10+ messages in thread From: Marek Vasut @ 2019-03-22 12:09 UTC (permalink / raw) To: u-boot On 3/22/19 1:06 PM, Simon Goldschmidt wrote: > On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: >> >> On 3/22/19 10:15 AM, Ley Foon Tan wrote: >>> Add QSPI device tree to Stratix 10. >>> Sync from Linux Stratix 10 dts. >>> >>> Tested on Stratix 10 SoC devkit. >>> SOCFPGA_STRATIX10 # sf probe 0:0 >>> SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB >>> >>> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> >>> --- >>> arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ >>> arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ >>> 2 files changed, 36 insertions(+) >>> >>> diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi >>> index ee93725d64..9998bb1ba3 100644 >>> --- a/arch/arm/dts/socfpga_stratix10.dtsi >>> +++ b/arch/arm/dts/socfpga_stratix10.dtsi >>> @@ -391,5 +391,20 @@ >>> resets = <&rst WATCHDOG3_RESET>; >>> status = "disabled"; >>> }; >>> + >>> + qspi: spi at ff8d2000 { >>> + compatible = "cdns,qspi-nor"; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + reg = <0xff8d2000 0x100>, >>> + <0xff900000 0x100000>; >>> + interrupts = <0 3 4>; >>> + cdns,fifo-depth = <128>; >>> + cdns,fifo-width = <4>; >>> + cdns,trigger-address = <0x00000000>; >>> + bus-num = <0>; >>> + status = "disabled"; >>> + u-boot,dm-pre-reloc; >>> + }; >>> }; >>> }; >>> diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts >>> index c59b77d829..4c47415b51 100644 >>> --- a/arch/arm/dts/socfpga_stratix10_socdk.dts >>> +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts >>> @@ -10,6 +10,7 @@ >>> >>> aliases { >>> serial0 = &uart0; >>> + spi0 = &qspi; >>> }; >>> >>> chosen { >>> @@ -87,6 +88,26 @@ >>> smplsel = <0>; >>> }; >>> >>> +&qspi { >>> + status = "okay"; >>> + >>> + flash at 0 { >>> + u-boot,dm-pre-reloc; >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + compatible = "spi-flash"; >>> + reg = <0>; /* chip select */ >>> + spi-max-frequency = <50000000>; >> >> The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 MHz ? > > I wonder who, when and why they were switched to 100 MHz, as they were at 50 MHz > in the past as well, or am I wrong? I was under the impression they were 100 since the beginning of times. Where did you find 50 MHz ? -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 12:09 ` Marek Vasut @ 2019-03-22 12:18 ` Simon Goldschmidt 2019-03-22 12:27 ` Simon Goldschmidt 0 siblings, 1 reply; 10+ messages in thread From: Simon Goldschmidt @ 2019-03-22 12:18 UTC (permalink / raw) To: u-boot On Fri, Mar 22, 2019 at 1:10 PM Marek Vasut <marex@denx.de> wrote: > > On 3/22/19 1:06 PM, Simon Goldschmidt wrote: > > On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: > >> > >> On 3/22/19 10:15 AM, Ley Foon Tan wrote: > >>> Add QSPI device tree to Stratix 10. > >>> Sync from Linux Stratix 10 dts. > >>> > >>> Tested on Stratix 10 SoC devkit. > >>> SOCFPGA_STRATIX10 # sf probe 0:0 > >>> SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB > >>> > >>> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > >>> --- > >>> arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > >>> arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > >>> 2 files changed, 36 insertions(+) > >>> > >>> diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi > >>> index ee93725d64..9998bb1ba3 100644 > >>> --- a/arch/arm/dts/socfpga_stratix10.dtsi > >>> +++ b/arch/arm/dts/socfpga_stratix10.dtsi > >>> @@ -391,5 +391,20 @@ > >>> resets = <&rst WATCHDOG3_RESET>; > >>> status = "disabled"; > >>> }; > >>> + > >>> + qspi: spi at ff8d2000 { > >>> + compatible = "cdns,qspi-nor"; > >>> + #address-cells = <1>; > >>> + #size-cells = <0>; > >>> + reg = <0xff8d2000 0x100>, > >>> + <0xff900000 0x100000>; > >>> + interrupts = <0 3 4>; > >>> + cdns,fifo-depth = <128>; > >>> + cdns,fifo-width = <4>; > >>> + cdns,trigger-address = <0x00000000>; > >>> + bus-num = <0>; > >>> + status = "disabled"; > >>> + u-boot,dm-pre-reloc; > >>> + }; > >>> }; > >>> }; > >>> diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts > >>> index c59b77d829..4c47415b51 100644 > >>> --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > >>> +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > >>> @@ -10,6 +10,7 @@ > >>> > >>> aliases { > >>> serial0 = &uart0; > >>> + spi0 = &qspi; > >>> }; > >>> > >>> chosen { > >>> @@ -87,6 +88,26 @@ > >>> smplsel = <0>; > >>> }; > >>> > >>> +&qspi { > >>> + status = "okay"; > >>> + > >>> + flash at 0 { > >>> + u-boot,dm-pre-reloc; > >>> + #address-cells = <1>; > >>> + #size-cells = <1>; > >>> + compatible = "spi-flash"; > >>> + reg = <0>; /* chip select */ > >>> + spi-max-frequency = <50000000>; > >> > >> The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 MHz ? > > > > I wonder who, when and why they were switched to 100 MHz, as they were at 50 MHz > > in the past as well, or am I wrong? > > I was under the impression they were 100 since the beginning of times. > Where did you find 50 MHz ? Good question, let me dig on that. Regards, Simon ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 12:18 ` Simon Goldschmidt @ 2019-03-22 12:27 ` Simon Goldschmidt 2019-03-22 12:35 ` Marek Vasut 0 siblings, 1 reply; 10+ messages in thread From: Simon Goldschmidt @ 2019-03-22 12:27 UTC (permalink / raw) To: u-boot On Fri, Mar 22, 2019 at 1:18 PM Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> wrote: > > On Fri, Mar 22, 2019 at 1:10 PM Marek Vasut <marex@denx.de> wrote: > > > > On 3/22/19 1:06 PM, Simon Goldschmidt wrote: > > > On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: > > >> > > >> On 3/22/19 10:15 AM, Ley Foon Tan wrote: > > >>> Add QSPI device tree to Stratix 10. > > >>> Sync from Linux Stratix 10 dts. > > >>> > > >>> Tested on Stratix 10 SoC devkit. > > >>> SOCFPGA_STRATIX10 # sf probe 0:0 > > >>> SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB > > >>> > > >>> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > > >>> --- > > >>> arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > > >>> arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > > >>> 2 files changed, 36 insertions(+) > > >>> > > >>> diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi > > >>> index ee93725d64..9998bb1ba3 100644 > > >>> --- a/arch/arm/dts/socfpga_stratix10.dtsi > > >>> +++ b/arch/arm/dts/socfpga_stratix10.dtsi > > >>> @@ -391,5 +391,20 @@ > > >>> resets = <&rst WATCHDOG3_RESET>; > > >>> status = "disabled"; > > >>> }; > > >>> + > > >>> + qspi: spi at ff8d2000 { > > >>> + compatible = "cdns,qspi-nor"; > > >>> + #address-cells = <1>; > > >>> + #size-cells = <0>; > > >>> + reg = <0xff8d2000 0x100>, > > >>> + <0xff900000 0x100000>; > > >>> + interrupts = <0 3 4>; > > >>> + cdns,fifo-depth = <128>; > > >>> + cdns,fifo-width = <4>; > > >>> + cdns,trigger-address = <0x00000000>; > > >>> + bus-num = <0>; > > >>> + status = "disabled"; > > >>> + u-boot,dm-pre-reloc; > > >>> + }; > > >>> }; > > >>> }; > > >>> diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts > > >>> index c59b77d829..4c47415b51 100644 > > >>> --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > > >>> +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > > >>> @@ -10,6 +10,7 @@ > > >>> > > >>> aliases { > > >>> serial0 = &uart0; > > >>> + spi0 = &qspi; > > >>> }; > > >>> > > >>> chosen { > > >>> @@ -87,6 +88,26 @@ > > >>> smplsel = <0>; > > >>> }; > > >>> > > >>> +&qspi { > > >>> + status = "okay"; > > >>> + > > >>> + flash at 0 { > > >>> + u-boot,dm-pre-reloc; > > >>> + #address-cells = <1>; > > >>> + #size-cells = <1>; > > >>> + compatible = "spi-flash"; > > >>> + reg = <0>; /* chip select */ > > >>> + spi-max-frequency = <50000000>; > > >> > > >> The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 MHz ? > > > > > > I wonder who, when and why they were switched to 100 MHz, as they were at 50 MHz > > > in the past as well, or am I wrong? > > > > I was under the impression they were 100 since the beginning of times. > > Where did you find 50 MHz ? > > Good question, let me dig on that. Some boards were at 50 MHz before I merged the dt files from Linux: https://github.com/u-boot/u-boot/commit/c402e8170245a0ca2b9398185638b349eeff10a3 In contrast to the U-Boot dts, the Linux dts for e.g. the socrates board has been at 100 MHz from the beginning. I don't know if that is due to a limitation of the flash chips on those boards or if it has been an error when reading those specs... Regards, Simon ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 12:27 ` Simon Goldschmidt @ 2019-03-22 12:35 ` Marek Vasut 2019-03-22 12:42 ` Simon Goldschmidt 0 siblings, 1 reply; 10+ messages in thread From: Marek Vasut @ 2019-03-22 12:35 UTC (permalink / raw) To: u-boot On 3/22/19 1:27 PM, Simon Goldschmidt wrote: > On Fri, Mar 22, 2019 at 1:18 PM Simon Goldschmidt > <simon.k.r.goldschmidt@gmail.com> wrote: >> >> On Fri, Mar 22, 2019 at 1:10 PM Marek Vasut <marex@denx.de> wrote: >>> >>> On 3/22/19 1:06 PM, Simon Goldschmidt wrote: >>>> On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: >>>>> >>>>> On 3/22/19 10:15 AM, Ley Foon Tan wrote: >>>>>> Add QSPI device tree to Stratix 10. >>>>>> Sync from Linux Stratix 10 dts. >>>>>> >>>>>> Tested on Stratix 10 SoC devkit. >>>>>> SOCFPGA_STRATIX10 # sf probe 0:0 >>>>>> SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB >>>>>> >>>>>> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> >>>>>> --- >>>>>> arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ >>>>>> arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ >>>>>> 2 files changed, 36 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi >>>>>> index ee93725d64..9998bb1ba3 100644 >>>>>> --- a/arch/arm/dts/socfpga_stratix10.dtsi >>>>>> +++ b/arch/arm/dts/socfpga_stratix10.dtsi >>>>>> @@ -391,5 +391,20 @@ >>>>>> resets = <&rst WATCHDOG3_RESET>; >>>>>> status = "disabled"; >>>>>> }; >>>>>> + >>>>>> + qspi: spi at ff8d2000 { >>>>>> + compatible = "cdns,qspi-nor"; >>>>>> + #address-cells = <1>; >>>>>> + #size-cells = <0>; >>>>>> + reg = <0xff8d2000 0x100>, >>>>>> + <0xff900000 0x100000>; >>>>>> + interrupts = <0 3 4>; >>>>>> + cdns,fifo-depth = <128>; >>>>>> + cdns,fifo-width = <4>; >>>>>> + cdns,trigger-address = <0x00000000>; >>>>>> + bus-num = <0>; >>>>>> + status = "disabled"; >>>>>> + u-boot,dm-pre-reloc; >>>>>> + }; >>>>>> }; >>>>>> }; >>>>>> diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts >>>>>> index c59b77d829..4c47415b51 100644 >>>>>> --- a/arch/arm/dts/socfpga_stratix10_socdk.dts >>>>>> +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts >>>>>> @@ -10,6 +10,7 @@ >>>>>> >>>>>> aliases { >>>>>> serial0 = &uart0; >>>>>> + spi0 = &qspi; >>>>>> }; >>>>>> >>>>>> chosen { >>>>>> @@ -87,6 +88,26 @@ >>>>>> smplsel = <0>; >>>>>> }; >>>>>> >>>>>> +&qspi { >>>>>> + status = "okay"; >>>>>> + >>>>>> + flash at 0 { >>>>>> + u-boot,dm-pre-reloc; >>>>>> + #address-cells = <1>; >>>>>> + #size-cells = <1>; >>>>>> + compatible = "spi-flash"; >>>>>> + reg = <0>; /* chip select */ >>>>>> + spi-max-frequency = <50000000>; >>>>> >>>>> The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 MHz ? >>>> >>>> I wonder who, when and why they were switched to 100 MHz, as they were at 50 MHz >>>> in the past as well, or am I wrong? >>> >>> I was under the impression they were 100 since the beginning of times. >>> Where did you find 50 MHz ? >> >> Good question, let me dig on that. > > Some boards were at 50 MHz before I merged the dt files from Linux: > https://github.com/u-boot/u-boot/commit/c402e8170245a0ca2b9398185638b349eeff10a3 > > In contrast to the U-Boot dts, the Linux dts for e.g. the socrates > board has been > at 100 MHz from the beginning. > > I don't know if that is due to a limitation of the flash chips on > those boards or if > it has been an error when reading those specs... So it's a per-board thing then ? Let's see what Ley has to say about the S10 then . -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 12:35 ` Marek Vasut @ 2019-03-22 12:42 ` Simon Goldschmidt 2019-03-25 2:43 ` Ley Foon Tan 0 siblings, 1 reply; 10+ messages in thread From: Simon Goldschmidt @ 2019-03-22 12:42 UTC (permalink / raw) To: u-boot Marek Vasut <marex@denx.de> schrieb am Fr., 22. März 2019, 13:35: > On 3/22/19 1:27 PM, Simon Goldschmidt wrote: > > On Fri, Mar 22, 2019 at 1:18 PM Simon Goldschmidt > > <simon.k.r.goldschmidt@gmail.com> wrote: > >> > >> On Fri, Mar 22, 2019 at 1:10 PM Marek Vasut <marex@denx.de> wrote: > >>> > >>> On 3/22/19 1:06 PM, Simon Goldschmidt wrote: > >>>> On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: > >>>>> > >>>>> On 3/22/19 10:15 AM, Ley Foon Tan wrote: > >>>>>> Add QSPI device tree to Stratix 10. > >>>>>> Sync from Linux Stratix 10 dts. > >>>>>> > >>>>>> Tested on Stratix 10 SoC devkit. > >>>>>> SOCFPGA_STRATIX10 # sf probe 0:0 > >>>>>> SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, > total 256 MiB > >>>>>> > >>>>>> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > >>>>>> --- > >>>>>> arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > >>>>>> arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > >>>>>> 2 files changed, 36 insertions(+) > >>>>>> > >>>>>> diff --git a/arch/arm/dts/socfpga_stratix10.dtsi > b/arch/arm/dts/socfpga_stratix10.dtsi > >>>>>> index ee93725d64..9998bb1ba3 100644 > >>>>>> --- a/arch/arm/dts/socfpga_stratix10.dtsi > >>>>>> +++ b/arch/arm/dts/socfpga_stratix10.dtsi > >>>>>> @@ -391,5 +391,20 @@ > >>>>>> resets = <&rst WATCHDOG3_RESET>; > >>>>>> status = "disabled"; > >>>>>> }; > >>>>>> + > >>>>>> + qspi: spi at ff8d2000 { > >>>>>> + compatible = "cdns,qspi-nor"; > >>>>>> + #address-cells = <1>; > >>>>>> + #size-cells = <0>; > >>>>>> + reg = <0xff8d2000 0x100>, > >>>>>> + <0xff900000 0x100000>; > >>>>>> + interrupts = <0 3 4>; > >>>>>> + cdns,fifo-depth = <128>; > >>>>>> + cdns,fifo-width = <4>; > >>>>>> + cdns,trigger-address = <0x00000000>; > >>>>>> + bus-num = <0>; > >>>>>> + status = "disabled"; > >>>>>> + u-boot,dm-pre-reloc; > >>>>>> + }; > >>>>>> }; > >>>>>> }; > >>>>>> diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts > b/arch/arm/dts/socfpga_stratix10_socdk.dts > >>>>>> index c59b77d829..4c47415b51 100644 > >>>>>> --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > >>>>>> +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > >>>>>> @@ -10,6 +10,7 @@ > >>>>>> > >>>>>> aliases { > >>>>>> serial0 = &uart0; > >>>>>> + spi0 = &qspi; > >>>>>> }; > >>>>>> > >>>>>> chosen { > >>>>>> @@ -87,6 +88,26 @@ > >>>>>> smplsel = <0>; > >>>>>> }; > >>>>>> > >>>>>> +&qspi { > >>>>>> + status = "okay"; > >>>>>> + > >>>>>> + flash at 0 { > >>>>>> + u-boot,dm-pre-reloc; > >>>>>> + #address-cells = <1>; > >>>>>> + #size-cells = <1>; > >>>>>> + compatible = "spi-flash"; > >>>>>> + reg = <0>; /* chip select */ > >>>>>> + spi-max-frequency = <50000000>; > >>>>> > >>>>> The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 > MHz ? > >>>> > >>>> I wonder who, when and why they were switched to 100 MHz, as they > were at 50 MHz > >>>> in the past as well, or am I wrong? > >>> > >>> I was under the impression they were 100 since the beginning of times. > >>> Where did you find 50 MHz ? > >> > >> Good question, let me dig on that. > > > > Some boards were at 50 MHz before I merged the dt files from Linux: > > > https://github.com/u-boot/u-boot/commit/c402e8170245a0ca2b9398185638b349eeff10a3 > > > > In contrast to the U-Boot dts, the Linux dts for e.g. the socrates > > board has been > > at 100 MHz from the beginning. > > > > I don't know if that is due to a limitation of the flash chips on > > those boards or if > > it has been an error when reading those specs... > > So it's a per-board thing then ? Let's see what Ley has to say about the > S10 then . > From a devicetree point of view, it's a per-board thing. And it describes the flash chip, so yes, board specific. But it still seemed inconsistent. Regards, Simon ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 12:42 ` Simon Goldschmidt @ 2019-03-25 2:43 ` Ley Foon Tan 0 siblings, 0 replies; 10+ messages in thread From: Ley Foon Tan @ 2019-03-25 2:43 UTC (permalink / raw) To: u-boot On Fri, Mar 22, 2019 at 8:42 PM Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> wrote: > > Marek Vasut <marex@denx.de> schrieb am Fr., 22. März 2019, 13:35: > > > On 3/22/19 1:27 PM, Simon Goldschmidt wrote: > > > On Fri, Mar 22, 2019 at 1:18 PM Simon Goldschmidt > > > <simon.k.r.goldschmidt@gmail.com> wrote: > > >> > > >> On Fri, Mar 22, 2019 at 1:10 PM Marek Vasut <marex@denx.de> wrote: > > >>> > > >>> On 3/22/19 1:06 PM, Simon Goldschmidt wrote: > > >>>> On Fri, Mar 22, 2019 at 12:59 PM Marek Vasut <marex@denx.de> wrote: > > >>>>> > > >>>>> On 3/22/19 10:15 AM, Ley Foon Tan wrote: > > >>>>>> Add QSPI device tree to Stratix 10. > > >>>>>> Sync from Linux Stratix 10 dts. > > >>>>>> > > >>>>>> Tested on Stratix 10 SoC devkit. > > >>>>>> SOCFPGA_STRATIX10 # sf probe 0:0 > > >>>>>> SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, > > total 256 MiB > > >>>>>> > > >>>>>> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > > >>>>>> --- > > >>>>>> arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > > >>>>>> arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > > >>>>>> 2 files changed, 36 insertions(+) > > >>>>>> > > >>>>>> diff --git a/arch/arm/dts/socfpga_stratix10.dtsi > > b/arch/arm/dts/socfpga_stratix10.dtsi > > >>>>>> index ee93725d64..9998bb1ba3 100644 > > >>>>>> --- a/arch/arm/dts/socfpga_stratix10.dtsi > > >>>>>> +++ b/arch/arm/dts/socfpga_stratix10.dtsi > > >>>>>> @@ -391,5 +391,20 @@ > > >>>>>> resets = <&rst WATCHDOG3_RESET>; > > >>>>>> status = "disabled"; > > >>>>>> }; > > >>>>>> + > > >>>>>> + qspi: spi at ff8d2000 { > > >>>>>> + compatible = "cdns,qspi-nor"; > > >>>>>> + #address-cells = <1>; > > >>>>>> + #size-cells = <0>; > > >>>>>> + reg = <0xff8d2000 0x100>, > > >>>>>> + <0xff900000 0x100000>; > > >>>>>> + interrupts = <0 3 4>; > > >>>>>> + cdns,fifo-depth = <128>; > > >>>>>> + cdns,fifo-width = <4>; > > >>>>>> + cdns,trigger-address = <0x00000000>; > > >>>>>> + bus-num = <0>; > > >>>>>> + status = "disabled"; > > >>>>>> + u-boot,dm-pre-reloc; > > >>>>>> + }; > > >>>>>> }; > > >>>>>> }; > > >>>>>> diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts > > b/arch/arm/dts/socfpga_stratix10_socdk.dts > > >>>>>> index c59b77d829..4c47415b51 100644 > > >>>>>> --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > > >>>>>> +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > > >>>>>> @@ -10,6 +10,7 @@ > > >>>>>> > > >>>>>> aliases { > > >>>>>> serial0 = &uart0; > > >>>>>> + spi0 = &qspi; > > >>>>>> }; > > >>>>>> > > >>>>>> chosen { > > >>>>>> @@ -87,6 +88,26 @@ > > >>>>>> smplsel = <0>; > > >>>>>> }; > > >>>>>> > > >>>>>> +&qspi { > > >>>>>> + status = "okay"; > > >>>>>> + > > >>>>>> + flash at 0 { > > >>>>>> + u-boot,dm-pre-reloc; > > >>>>>> + #address-cells = <1>; > > >>>>>> + #size-cells = <1>; > > >>>>>> + compatible = "spi-flash"; > > >>>>>> + reg = <0>; /* chip select */ > > >>>>>> + spi-max-frequency = <50000000>; > > >>>>> > > >>>>> The other SoCFPGAs use 100 MHz for the CQSPI , why would S10 use 50 > > MHz ? > > >>>> > > >>>> I wonder who, when and why they were switched to 100 MHz, as they > > were at 50 MHz > > >>>> in the past as well, or am I wrong? > > >>> > > >>> I was under the impression they were 100 since the beginning of times. > > >>> Where did you find 50 MHz ? > > >> > > >> Good question, let me dig on that. > > > > > > Some boards were at 50 MHz before I merged the dt files from Linux: > > > > > https://github.com/u-boot/u-boot/commit/c402e8170245a0ca2b9398185638b349eeff10a3 > > > > > > In contrast to the U-Boot dts, the Linux dts for e.g. the socrates > > > board has been > > > at 100 MHz from the beginning. > > > > > > I don't know if that is due to a limitation of the flash chips on > > > those boards or if > > > it has been an error when reading those specs... > > > > So it's a per-board thing then ? Let's see what Ley has to say about the > > S10 then . > > > > From a devicetree point of view, it's a per-board thing. And it describes > the flash chip, so yes, board specific. But it still seemed inconsistent. > It should be 100MHz. QSPI reference clock is 400MHz. SPI flash clock can up to 100MHz. Dinh, Linux dts need to update this too. Please take note. Regards Ley Foon ^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node 2019-03-22 9:15 [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node Ley Foon Tan 2019-03-22 10:51 ` Marek Vasut @ 2019-03-22 11:43 ` Simon Goldschmidt 1 sibling, 0 replies; 10+ messages in thread From: Simon Goldschmidt @ 2019-03-22 11:43 UTC (permalink / raw) To: u-boot On Fri, Mar 22, 2019 at 10:15 AM Ley Foon Tan <ley.foon.tan@intel.com> wrote: > > Add QSPI device tree to Stratix 10. > Sync from Linux Stratix 10 dts. > > Tested on Stratix 10 SoC devkit. > SOCFPGA_STRATIX10 # sf probe 0:0 > SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB > > Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> > --- > arch/arm/dts/socfpga_stratix10.dtsi | 15 +++++++++++++++ > arch/arm/dts/socfpga_stratix10_socdk.dts | 21 +++++++++++++++++++++ > 2 files changed, 36 insertions(+) > > diff --git a/arch/arm/dts/socfpga_stratix10.dtsi b/arch/arm/dts/socfpga_stratix10.dtsi > index ee93725d64..9998bb1ba3 100644 > --- a/arch/arm/dts/socfpga_stratix10.dtsi > +++ b/arch/arm/dts/socfpga_stratix10.dtsi > @@ -391,5 +391,20 @@ > resets = <&rst WATCHDOG3_RESET>; > status = "disabled"; > }; > + > + qspi: spi at ff8d2000 { > + compatible = "cdns,qspi-nor"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0xff8d2000 0x100>, > + <0xff900000 0x100000>; > + interrupts = <0 3 4>; > + cdns,fifo-depth = <128>; > + cdns,fifo-width = <4>; > + cdns,trigger-address = <0x00000000>; > + bus-num = <0>; > + status = "disabled"; > + u-boot,dm-pre-reloc; > + }; > }; > }; > diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts > index c59b77d829..4c47415b51 100644 > --- a/arch/arm/dts/socfpga_stratix10_socdk.dts > +++ b/arch/arm/dts/socfpga_stratix10_socdk.dts > @@ -10,6 +10,7 @@ > > aliases { > serial0 = &uart0; > + spi0 = &qspi; > }; > > chosen { > @@ -87,6 +88,26 @@ > smplsel = <0>; > }; > > +&qspi { > + status = "okay"; > + > + flash at 0 { > + u-boot,dm-pre-reloc; > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "spi-flash"; "jedec,spi-nor", see my comment to in the other thread. > + reg = <0>; /* chip select */ > + spi-max-frequency = <50000000>; This has changed to the one sent 10 minutes ago, so it should be a v2, right? > + > + page-size = <256>; > + block-size = <16>; /* 2^16, 64KB */ > + cdns,tshsl-ns = <50>; > + cdns,tsd2d-ns = <50>; > + cdns,tchsh-ns = <4>; > + cdns,tslch-ns = <4>; > + }; > +}; > + > &uart0 { > status = "okay"; > }; > -- > 2.19.0 ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2019-03-25 2:43 UTC | newest] Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-03-22 9:15 [U-Boot] [RESEND] [PATCH] arm: dts: Stratix10: Add QSPI node Ley Foon Tan 2019-03-22 10:51 ` Marek Vasut 2019-03-22 12:06 ` Simon Goldschmidt 2019-03-22 12:09 ` Marek Vasut 2019-03-22 12:18 ` Simon Goldschmidt 2019-03-22 12:27 ` Simon Goldschmidt 2019-03-22 12:35 ` Marek Vasut 2019-03-22 12:42 ` Simon Goldschmidt 2019-03-25 2:43 ` Ley Foon Tan 2019-03-22 11:43 ` Simon Goldschmidt
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.