All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v2 01/14] board: freescale: Refactor NXP common mux code
@ 2021-06-24 19:32 Stephen Carlson
  2021-07-12  7:50 ` Priyanka Jain
  0 siblings, 1 reply; 2+ messages in thread
From: Stephen Carlson @ 2021-06-24 19:32 UTC (permalink / raw)
  To: U-Boot Mailing List; +Cc: Priyanka Jain

Refactors similar mux code from multiple NXP boards into a common location,
and allows it to be disabled in config.

New config: CONFIG_FSL_USE_PCA9547_MUX to enable PCA9547 mux functionality.

Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
---
  board/freescale/common/Kconfig      |  6 +++
  board/freescale/common/Makefile     | 11 ++++++
  board/freescale/common/i2c_common.c | 34 +++++++++++++++++
  board/freescale/common/i2c_common.h | 30 +++++++++++++++
  board/freescale/common/i2c_mux.c    | 40 ++++++++++++++++++++
  board/freescale/common/i2c_mux.h    | 15 ++++++++
  board/freescale/common/vid.c        | 58 ++++++-----------------------
  7 files changed, 148 insertions(+), 46 deletions(-)
  create mode 100644 board/freescale/common/i2c_common.c
  create mode 100644 board/freescale/common/i2c_common.h
  create mode 100644 board/freescale/common/i2c_mux.c
  create mode 100644 board/freescale/common/i2c_mux.h

diff --git a/board/freescale/common/Kconfig b/board/freescale/common/Kconfig
index 17db755951..ab9c14ae88 100644
--- a/board/freescale/common/Kconfig
+++ b/board/freescale/common/Kconfig
@@ -21,6 +21,12 @@ config CMD_ESBC_VALIDATE
  	    esbc_validate - validate signature using RSA verification
  	    esbc_halt - put the core in spin loop (Secure Boot Only)

+config FSL_USE_PCA9547_MUX
+	bool "Enable PCA9547 I2C Mux on Freescale boards"
+	default n
+	help
+	 This option enables the PCA9547 I2C mux on Freescale boards.
+
  config VID
  	depends on DM_I2C
  	bool "Enable Freescale VID"
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 114b7ba8f9..45aaa16ca4 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -15,6 +15,15 @@ ifdef MINIMAL
  # necessary to create built-in.o
  obj- := __dummy__.o
  else
+# include i2c_common.o once if either VID or FSL_USE_PCA9547_MUX
+I2C_COMMON=
+ifdef CONFIG_VID
+I2C_COMMON=y
+endif
+ifdef CONFIG_FSL_USE_PCA9547_MUX
+I2C_COMMON=y
+endif
+
  obj-$(CONFIG_FSL_CADMUS)	+= cadmus.o
  obj-$(CONFIG_FSL_VIA)		+= cds_via.o
  obj-$(CONFIG_FMAN_ENET)	+= fman.o
@@ -22,6 +31,8 @@ obj-$(CONFIG_FSL_PIXIS)	+= pixis.o
  ifndef CONFIG_SPL_BUILD
  obj-$(CONFIG_FSL_NGPIXIS)	+= ngpixis.o
  endif
+obj-$(I2C_COMMON)		+= i2c_common.o
+obj-$(CONFIG_FSL_USE_PCA9547_MUX)		+= i2c_mux.o
  obj-$(CONFIG_VID)		+= vid.o
  obj-$(CONFIG_FSL_QIXIS)	+= qixis.o
  obj-$(CONFIG_PQ_MDS_PIB)	+= pq-mds-pib.o
diff --git a/board/freescale/common/i2c_common.c b/board/freescale/common/i2c_common.c
new file mode 100644
index 0000000000..0f09ed7d34
--- /dev/null
+++ b/board/freescale/common/i2c_common.c
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020-21 NXP
+ * Copyright 2021 Microsoft Corporation
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include "i2c_common.h"
+
+#ifdef CONFIG_DM_I2C
+
+/* If DM is in use, retrieve the chip for the specified bus number */
+int fsl_i2c_get_device(int address, int bus, DEVICE_HANDLE_T *dev)
+{
+	int ret = i2c_get_chip_for_busnum(bus, address, 1, dev);
+
+	if (ret)
+		printf("I2C: Bus %d has no device with address 0x%02X\n",
+		       bus, address);
+	return ret;
+}
+
+#else
+
+/* Handle is passed directly */
+int fsl_i2c_get_device(int address, int bus, DEVICE_HANDLE_T *dev)
+{
+	*dev = address;
+	return 0;
+}
+
+#endif
diff --git a/board/freescale/common/i2c_common.h b/board/freescale/common/i2c_common.h
new file mode 100644
index 0000000000..840ad66183
--- /dev/null
+++ b/board/freescale/common/i2c_common.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020-21 NXP
+ * Copyright 2021 Microsoft Corporation
+ */
+
+#ifndef __NXP_I2C_COMMON_H__
+#define __NXP_I2C_COMMON_H__
+
+/* Common functionality shared by the I2C drivers for VID and the mux. */
+#ifdef CONFIG_DM_I2C
+#define DEVICE_HANDLE_T struct udevice *
+
+#define I2C_READ(dev, register, data, length) \
+	dm_i2c_read(dev, register, data, length)
+#define I2C_WRITE(dev, register, data, length) \
+	dm_i2c_write(dev, register, data, length)
+#else
+#define DEVICE_HANDLE_T int
+
+#define I2C_READ(dev, register, data, length) \
+	i2c_read(dev, register, 1, data, length)
+#define I2C_WRITE(dev, register, data, length) \
+	i2c_write(dev, register, 1, data, length)
+#endif
+
+int fsl_i2c_get_device(int address, int bus, DEVICE_HANDLE_T *dev);
+
+#endif
diff --git a/board/freescale/common/i2c_mux.c b/board/freescale/common/i2c_mux.c
new file mode 100644
index 0000000000..54f89e2576
--- /dev/null
+++ b/board/freescale/common/i2c_mux.c
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020-21 NXP
+ * Copyright 2021 Microsoft Corporation
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include "i2c_common.h"
+#include "i2c_mux.h"
+
+/*
+ * A new Kconfig option for something that used to always be built should be
+ * “default y”.
+ */
+#ifdef CONFIG_FSL_USE_PCA9547_MUX
+
+int select_i2c_ch_pca9547(u8 ch, int bus)
+{
+	int ret;
+	DEVICE_HANDLE_T dev;
+
+	/* Open device handle */
+	ret = fsl_i2c_get_device(I2C_MUX_PCA_ADDR_PRI, bus, &dev);
+	if (ret) {
+		printf("PCA: No PCA9547 device found\n");
+		return ret;
+	}
+
+	ret = I2C_WRITE(dev, 0, &ch, sizeof(ch));
+	if (ret) {
+		printf("PCA: Unable to select channel %d (%d)\n", (int)ch, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+#endif
diff --git a/board/freescale/common/i2c_mux.h b/board/freescale/common/i2c_mux.h
new file mode 100644
index 0000000000..0870c1918e
--- /dev/null
+++ b/board/freescale/common/i2c_mux.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020-21 NXP
+ * Copyright 2021 Microsoft Corporation
+ */
+
+#ifndef __NXP_I2C_MUX_H__
+#define __NXP_I2C_MUX_H__
+
+#ifdef CONFIG_FSL_USE_PCA9547_MUX
+int select_i2c_ch_pca9547(u8 ch, int bus);
+#endif
+
+#endif
diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c
index 13ef101e7f..d2c9bbbfe9 100644
--- a/board/freescale/common/vid.c
+++ b/board/freescale/common/vid.c
@@ -20,8 +20,13 @@
  #include <asm/immap_85xx.h>
  #endif
  #include <linux/delay.h>
+#include "i2c_common.h"
  #include "vid.h"

+#ifndef I2C_VOL_MONITOR_BUS
+#define I2C_VOL_MONITOR_BUS                    0
+#endif
+
  /* Voltages are generally handled in mV to keep them as integers */
  #define MV_PER_V 1000

@@ -95,44 +100,6 @@ u16 __weak soc_get_fuse_vid(int vid_index)
  #define I2C_VOL_MONITOR_ADDR                    0
  #endif

-#if CONFIG_IS_ENABLED(DM_I2C)
-#define DEVICE_HANDLE_T struct udevice *
-
-#ifndef I2C_VOL_MONITOR_BUS
-#define I2C_VOL_MONITOR_BUS			0
-#endif
-
-/* If DM is in use, retrieve the udevice chip for the specified bus number */
-static int vid_get_device(int address, DEVICE_HANDLE_T *dev)
-{
-	int ret = i2c_get_chip_for_busnum(I2C_VOL_MONITOR_BUS, address, 1, dev);
-
-	if (ret)
-		printf("VID: Bus %d has no device with address 0x%02X\n",
-		       I2C_VOL_MONITOR_BUS, address);
-	return ret;
-}
-
-#define I2C_READ(dev, register, data, length) \
-	dm_i2c_read(dev, register, data, length)
-#define I2C_WRITE(dev, register, data, length) \
-	dm_i2c_write(dev, register, data, length)
-#else
-#define DEVICE_HANDLE_T int
-
-/* If DM is not in use, I2C addresses are passed directly */
-static int vid_get_device(int address, DEVICE_HANDLE_T *dev)
-{
-	*dev = address;
-	return 0;
-}
-
-#define I2C_READ(dev, register, data, length) \
-	i2c_read(dev, register, 1, data, length)
-#define I2C_WRITE(dev, register, data, length) \
-	i2c_write(dev, register, 1, data, length)
-#endif
-
  #if defined(CONFIG_VOL_MONITOR_IR36021_SET) || \
  	defined(CONFIG_VOL_MONITOR_IR36021_READ)
  /*
@@ -158,7 +125,7 @@ static int find_ir_chip_on_i2c(void)
  	/* Check all the address */
  	for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) {
  		i2caddress = ir_i2c_addr[i];
-		ret = vid_get_device(i2caddress, &dev);
+		ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  		if (!ret) {
  			ret = I2C_READ(dev, IR36021_MFR_ID_OFFSET,
  				       (void *)&mfrID, sizeof(mfrID));
@@ -202,7 +169,7 @@ static int read_voltage_from_INA220(int i2caddress)
  	DEVICE_HANDLE_T dev;

  	/* Open device handle */
-	ret = vid_get_device(i2caddress, &dev);
+	ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  	if (ret)
  		return ret;

@@ -243,7 +210,7 @@ static int read_voltage_from_IR(int i2caddress)
  	DEVICE_HANDLE_T dev;

  	/* Open device handle */
-	ret = vid_get_device(i2caddress, &dev);
+	ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  	if (ret)
  		return ret;

@@ -344,7 +311,7 @@ static int read_voltage_from_pmbus(int i2caddress)
  	DEVICE_HANDLE_T dev;

  	/* Open device handle */
-	ret = vid_get_device(i2caddress, &dev);
+	ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  	if (ret)
  		return ret;

@@ -457,7 +424,7 @@ static int set_voltage_to_IR(int i2caddress, int vdd)
  	DEVICE_HANDLE_T dev;

  	/* Open device handle */
-	ret = vid_get_device(i2caddress, &dev);
+	ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  	if (ret)
  		return ret;

@@ -503,7 +470,7 @@ static int set_voltage_to_pmbus(int i2caddress, int vdd)
  	DEVICE_HANDLE_T dev;

  	/* Open device handle */
-	ret = vid_get_device(i2caddress, &dev);
+	ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  	if (ret)
  		return ret;

@@ -653,7 +620,7 @@ int adjust_vdd(ulong vdd_override)
  		debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
  	}

-	ret = vid_get_device(i2caddress, &dev);
+	ret = fsl_i2c_get_device(i2caddress, I2C_VOL_MONITOR_BUS, &dev);
  	if (ret)
  		return ret;

@@ -785,7 +752,6 @@ exit:
  	i2c_multiplexer_select_vid_channel(I2C_MUX_CH_DEFAULT);

  	return ret < 0 ? -1 : 0;
-
  }

  static int do_vdd_override(struct cmd_tbl *cmdtp,
-- 
2.17.1

^ permalink raw reply related	[flat|nested] 2+ messages in thread
* RE: [PATCH v2 01/14] board: freescale: Refactor NXP common mux code
  2021-06-24 19:32 [PATCH v2 01/14] board: freescale: Refactor NXP common mux code Stephen Carlson
@ 2021-07-12  7:50 ` Priyanka Jain
  0 siblings, 0 replies; 2+ messages in thread
From: Priyanka Jain @ 2021-07-12  7:50 UTC (permalink / raw)
  To: Stephen Carlson, U-Boot Mailing List



>-----Original Message-----
>From: Stephen Carlson <stcarlso@linux.microsoft.com>
>Sent: Friday, June 25, 2021 1:02 AM
>To: U-Boot Mailing List <u-boot@lists.denx.de>
>Cc: Priyanka Jain <priyanka.jain@nxp.com>
>Subject: [PATCH v2 01/14] board: freescale: Refactor NXP common mux code
>
>Refactors similar mux code from multiple NXP boards into a common location,
>and allows it to be disabled in config.
>
>New config: CONFIG_FSL_USE_PCA9547_MUX to enable PCA9547 mux
>functionality.
>
>Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
>---
>  board/freescale/common/Kconfig      |  6 +++
>  board/freescale/common/Makefile     | 11 ++++++
>  board/freescale/common/i2c_common.c | 34 +++++++++++++++++
>  board/freescale/common/i2c_common.h | 30 +++++++++++++++
>  board/freescale/common/i2c_mux.c    | 40 ++++++++++++++++++++
>  board/freescale/common/i2c_mux.h    | 15 ++++++++
>  board/freescale/common/vid.c        | 58 ++++++-----------------------
>  7 files changed, 148 insertions(+), 46 deletions(-)
>  create mode 100644 board/freescale/common/i2c_common.c
>  create mode 100644 board/freescale/common/i2c_common.h
>  create mode 100644 board/freescale/common/i2c_mux.c
>  create mode 100644 board/freescale/common/i2c_mux.h
>
>diff --git a/board/freescale/common/Kconfig
>b/board/freescale/common/Kconfig index 17db755951..ab9c14ae88 100644
>--- a/board/freescale/common/Kconfig
>+++ b/board/freescale/common/Kconfig
>@@ -21,6 +21,12 @@ config CMD_ESBC_VALIDATE
>  	    esbc_validate - validate signature using RSA verification
>  	    esbc_halt - put the core in spin loop (Secure Boot Only)
>
>+config FSL_USE_PCA9547_MUX
>+	bool "Enable PCA9547 I2C Mux on Freescale boards"
>+	default n
>+	help
>+	 This option enables the PCA9547 I2C mux on Freescale boards.
>+
>  config VID
>  	depends on DM_I2C
>  	bool "Enable Freescale VID"
>diff --git a/board/freescale/common/Makefile
>b/board/freescale/common/Makefile index 114b7ba8f9..45aaa16ca4 100644
>--- a/board/freescale/common/Makefile
>+++ b/board/freescale/common/Makefile
>@@ -15,6 +15,15 @@ ifdef MINIMAL
>  # necessary to create built-in.o
>  obj- := __dummy__.o
>  else
>+# include i2c_common.o once if either VID or FSL_USE_PCA9547_MUX
>+I2C_COMMON= ifdef CONFIG_VID I2C_COMMON=y endif ifdef
>+CONFIG_FSL_USE_PCA9547_MUX I2C_COMMON=y endif
>+
>  obj-$(CONFIG_FSL_CADMUS)	+= cadmus.o
>  obj-$(CONFIG_FSL_VIA)		+= cds_via.o
>  obj-$(CONFIG_FMAN_ENET)	+= fman.o
>@@ -22,6 +31,8 @@ obj-$(CONFIG_FSL_PIXIS)	+= pixis.o
>  ifndef CONFIG_SPL_BUILD
>  obj-$(CONFIG_FSL_NGPIXIS)	+= ngpixis.o
>  endif
>+obj-$(I2C_COMMON)		+= i2c_common.o
>+obj-$(CONFIG_FSL_USE_PCA9547_MUX)		+= i2c_mux.o
>  obj-$(CONFIG_VID)		+= vid.o
>  obj-$(CONFIG_FSL_QIXIS)	+= qixis.o
>  obj-$(CONFIG_PQ_MDS_PIB)	+= pq-mds-pib.o
>diff --git a/board/freescale/common/i2c_common.c
>b/board/freescale/common/i2c_common.c
>new file mode 100644
>index 0000000000..0f09ed7d34
>--- /dev/null
>+++ b/board/freescale/common/i2c_common.c
>@@ -0,0 +1,34 @@
>+// SPDX-License-Identifier: GPL-2.0+
>+/*
>+ * Copyright 2014 Freescale Semiconductor, Inc.
>+ * Copyright 2020-21 NXP
>+ * Copyright 2021 Microsoft Corporation  */
>+
>+#include <common.h>
>+#include <i2c.h>
>+#include "i2c_common.h"
>+
>+#ifdef CONFIG_DM_I2C
>+
>+/* If DM is in use, retrieve the chip for the specified bus number */
>+int fsl_i2c_get_device(int address, int bus, DEVICE_HANDLE_T *dev) {
>+	int ret = i2c_get_chip_for_busnum(bus, address, 1, dev);
>+
>+	if (ret)
>+		printf("I2C: Bus %d has no device with address 0x%02X\n",
>+		       bus, address);
>+	return ret;
>+}
>+
>+#else
>+
>+/* Handle is passed directly */
>+int fsl_i2c_get_device(int address, int bus, DEVICE_HANDLE_T *dev) {
>+	*dev = address;
>+	return 0;
>+}
>+
>+#endif
>
<snip>
Stephen,

All patches in the series has one extra space character in start on each line due to which patch does not apply with git am.
Please re-send the series after removing the extra character. Do ensure git am <patch> run successfully.

Also there are some changes in vid.c on master branch, please rebase to top.

Regards
Priyanka


^ permalink raw reply	[flat|nested] 2+ messages in thread
end of thread, other threads:[~2021-07-12  7:50 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-24 19:32 [PATCH v2 01/14] board: freescale: Refactor NXP common mux code Stephen Carlson
2021-07-12  7:50 ` Priyanka Jain

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.