* [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905)
[not found] <f28d33f6-8c8a-c40e-1ae4-cc5f7e4f9511@gmail.com>
@ 2017-01-27 20:55 ` Heiner Kallweit
2017-01-31 13:24 ` Jaehoon Chung
2017-01-27 20:56 ` [U-Boot] [PATCH v3 3/3] odroid-c2: enable new Meson GX MMC driver in board defconfig Heiner Kallweit
1 sibling, 1 reply; 7+ messages in thread
From: Heiner Kallweit @ 2017-01-27 20:55 UTC (permalink / raw)
To: u-boot
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas F?rber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
---
v2:
- addressed review comments
- general refactoring
v3:
- remove config symbol MMC_MESON_GX_SD_PORT
---
arch/arm/include/asm/arch-meson/sd_emmc.h | 89 +++++++++
drivers/mmc/Kconfig | 6 +
drivers/mmc/Makefile | 1 +
drivers/mmc/meson_gx_mmc.c | 291 ++++++++++++++++++++++++++++++
include/configs/meson-gxbb-common.h | 4 +
5 files changed, 391 insertions(+)
create mode 100644 arch/arm/include/asm/arch-meson/sd_emmc.h
create mode 100644 drivers/mmc/meson_gx_mmc.c
diff --git a/arch/arm/include/asm/arch-meson/sd_emmc.h b/arch/arm/include/asm/arch-meson/sd_emmc.h
new file mode 100644
index 0000000..25dbf60
--- /dev/null
+++ b/arch/arm/include/asm/arch-meson/sd_emmc.h
@@ -0,0 +1,89 @@
+/*
+ * (C) Copyright 2017 Carlo Caione <carlo@caione.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __SD_EMMC_H__
+#define __SD_EMMC_H__
+
+#include <mmc.h>
+
+#define SDIO_PORT_A 0
+#define SDIO_PORT_B 1
+#define SDIO_PORT_C 2
+
+#define SD_EMMC_CLKSRC_24M 24000000 /* 24 MHz */
+#define SD_EMMC_CLKSRC_DIV2 1000000000 /* 1 GHz */
+
+#define MESON_SD_EMMC_CLOCK 0x00
+#define CLK_MAX_DIV 63
+#define CLK_SRC_24M (0 << 6)
+#define CLK_SRC_DIV2 (1 << 6)
+#define CLK_CO_PHASE_000 (0 << 8)
+#define CLK_CO_PHASE_090 (1 << 8)
+#define CLK_CO_PHASE_180 (2 << 8)
+#define CLK_CO_PHASE_270 (3 << 8)
+#define CLK_TX_PHASE_000 (0 << 10)
+#define CLK_TX_PHASE_090 (1 << 10)
+#define CLK_TX_PHASE_180 (2 << 10)
+#define CLK_TX_PHASE_270 (3 << 10)
+#define CLK_ALWAYS_ON BIT(24)
+
+#define MESON_SD_EMMC_CFG 0x44
+#define CFG_BUS_WIDTH_MASK GENMASK(1, 0)
+#define CFG_BUS_WIDTH_1 0
+#define CFG_BUS_WIDTH_4 1
+#define CFG_BUS_WIDTH_8 2
+#define CFG_BL_LEN_MASK GENMASK(7, 4)
+#define CFG_BL_LEN_SHIFT 4
+#define CFG_BL_LEN_512 (9 << 4)
+#define CFG_RESP_TIMEOUT_MASK GENMASK(11, 8)
+#define CFG_RESP_TIMEOUT_256 (8 << 8)
+#define CFG_RC_CC_MASK GENMASK(15, 12)
+#define CFG_RC_CC_16 (4 << 12)
+#define CFG_SDCLK_ALWAYS_ON BIT(18)
+#define CFG_AUTO_CLK BIT(23)
+
+#define MESON_SD_EMMC_STATUS 0x48
+#define STATUS_MASK GENMASK(15, 0)
+#define STATUS_ERR_MASK GENMASK(12, 0)
+#define STATUS_RXD_ERR_MASK GENMASK(7, 0)
+#define STATUS_TXD_ERR BIT(8)
+#define STATUS_DESC_ERR BIT(9)
+#define STATUS_RESP_ERR BIT(10)
+#define STATUS_RESP_TIMEOUT BIT(11)
+#define STATUS_DESC_TIMEOUT BIT(12)
+#define STATUS_END_OF_CHAIN BIT(13)
+
+#define MESON_SD_EMMC_IRQ_EN 0x4c
+
+#define MESON_SD_EMMC_CMD_CFG 0x50
+#define CMD_CFG_LENGTH_MASK GENMASK(8, 0)
+#define CMD_CFG_BLOCK_MODE BIT(9)
+#define CMD_CFG_R1B BIT(10)
+#define CMD_CFG_END_OF_CHAIN BIT(11)
+#define CMD_CFG_TIMEOUT_4S (12 << 12)
+#define CMD_CFG_NO_RESP BIT(16)
+#define CMD_CFG_DATA_IO BIT(18)
+#define CMD_CFG_DATA_WR BIT(19)
+#define CMD_CFG_RESP_NOCRC BIT(20)
+#define CMD_CFG_RESP_128 BIT(21)
+#define CMD_CFG_CMD_INDEX_SHIFT 24
+#define CMD_CFG_OWNER BIT(31)
+
+#define MESON_SD_EMMC_CMD_ARG 0x54
+#define MESON_SD_EMMC_CMD_DAT 0x58
+#define MESON_SD_EMMC_CMD_RSP 0x5c
+#define MESON_SD_EMMC_CMD_RSP1 0x60
+#define MESON_SD_EMMC_CMD_RSP2 0x64
+#define MESON_SD_EMMC_CMD_RSP3 0x68
+
+struct meson_mmc_platdata {
+ struct mmc_config cfg;
+ struct mmc mmc;
+ void *regbase;
+ void *w_buf;
+};
+
+#endif
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index 147e52d..ffae684 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -168,6 +168,12 @@ config ZYNQ_SDHCI
help
Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform
+config MMC_MESON_GX
+ bool "Meson GX EMMC controller support"
+ depends on DM_MMC && BLK && DM_MMC_OPS && ARCH_MESON
+ help
+ Support for EMMC host controller on Meson GX ARM SoCs platform (S905)
+
config ROCKCHIP_SDHCI
bool "Arasan SDHCI controller for Rockchip support"
depends on DM_MMC && BLK && DM_MMC_OPS
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index 6af7f79..baa6531 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -31,6 +31,7 @@ ifdef CONFIG_SUPPORT_EMMC_BOOT
obj-$(CONFIG_GENERIC_MMC) += mmc_boot.o
endif
obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o
+obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o
obj-$(CONFIG_MMC_SPI) += mmc_spi.o
obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o
obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o
diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
new file mode 100644
index 0000000..612a81e
--- /dev/null
+++ b/drivers/mmc/meson_gx_mmc.c
@@ -0,0 +1,291 @@
+/*
+ * (C) Copyright 2017 Carlo Caione <carlo@caione.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <asm/io.h>
+#include <asm/arch/sd_emmc.h>
+#include <dm/device.h>
+#include <linux/log2.h>
+
+static inline void *get_regbase(const struct mmc *mmc)
+{
+ struct meson_mmc_platdata *pdata = mmc->priv;
+
+ return pdata->regbase;
+}
+
+static inline uint32_t meson_read(struct mmc *mmc, int offset)
+{
+ return readl(get_regbase(mmc) + offset);
+}
+
+static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
+{
+ writel(val, get_regbase(mmc) + offset);
+}
+
+static void meson_mmc_config_clock(struct mmc *mmc)
+{
+ uint32_t meson_mmc_clk = 0;
+ unsigned int clk, clk_src, clk_div;
+
+ /* 1GHz / CLK_MAX_DIV = 15,9 MHz */
+ if (mmc->clock > 16000000) {
+ clk = SD_EMMC_CLKSRC_DIV2;
+ clk_src = CLK_SRC_DIV2;
+ } else {
+ clk = SD_EMMC_CLKSRC_24M;
+ clk_src = CLK_SRC_24M;
+ }
+ clk_div = DIV_ROUND_UP(clk, mmc->clock);
+
+ /* 180 phase core clock */
+ meson_mmc_clk |= CLK_CO_PHASE_180;
+
+ /* 180 phase tx clock */
+ meson_mmc_clk |= CLK_TX_PHASE_180;
+
+ /* clock settings */
+ meson_mmc_clk |= clk_src;
+ meson_mmc_clk |= clk_div;
+
+ meson_write(mmc, meson_mmc_clk, MESON_SD_EMMC_CLOCK);
+}
+
+static int meson_dm_mmc_set_ios(struct udevice *dev)
+{
+ struct mmc *mmc = mmc_get_mmc_dev(dev);
+ uint32_t meson_mmc_cfg;
+
+ meson_mmc_config_clock(mmc);
+
+ meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
+
+ meson_mmc_cfg &= ~CFG_BUS_WIDTH_MASK;
+ if (mmc->bus_width == 1)
+ meson_mmc_cfg |= CFG_BUS_WIDTH_1;
+ else if (mmc->bus_width == 4)
+ meson_mmc_cfg |= CFG_BUS_WIDTH_4;
+ else if (mmc->bus_width == 8)
+ meson_mmc_cfg |= CFG_BUS_WIDTH_8;
+ else
+ return -EINVAL;
+
+ /* 512 bytes block length */
+ meson_mmc_cfg &= ~CFG_BL_LEN_MASK;
+ meson_mmc_cfg |= CFG_BL_LEN_512;
+
+ /* Response timeout 256 clk */
+ meson_mmc_cfg &= ~CFG_RESP_TIMEOUT_MASK;
+ meson_mmc_cfg |= CFG_RESP_TIMEOUT_256;
+
+ /* Command-command gap 16 clk */
+ meson_mmc_cfg &= ~CFG_RC_CC_MASK;
+ meson_mmc_cfg |= CFG_RC_CC_16;
+
+ meson_write(mmc, meson_mmc_cfg, MESON_SD_EMMC_CFG);
+
+ return 0;
+}
+
+static void meson_mmc_setup_cmd(struct mmc *mmc, struct mmc_data *data,
+ struct mmc_cmd *cmd)
+{
+ uint32_t meson_mmc_cmd = 0, cfg;
+
+ meson_mmc_cmd |= cmd->cmdidx << CMD_CFG_CMD_INDEX_SHIFT;
+
+ if (cmd->resp_type & MMC_RSP_PRESENT) {
+ if (cmd->resp_type & MMC_RSP_136)
+ meson_mmc_cmd |= CMD_CFG_RESP_128;
+
+ if (cmd->resp_type & MMC_RSP_BUSY)
+ meson_mmc_cmd |= CMD_CFG_R1B;
+
+ if (!(cmd->resp_type & MMC_RSP_CRC))
+ meson_mmc_cmd |= CMD_CFG_RESP_NOCRC;
+ } else {
+ meson_mmc_cmd |= CMD_CFG_NO_RESP;
+ }
+
+ if (data) {
+ cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
+ cfg &= ~CFG_BL_LEN_MASK;
+ cfg |= ilog2(data->blocksize) << CFG_BL_LEN_SHIFT;
+ meson_write(mmc, cfg, MESON_SD_EMMC_CFG);
+
+ if (data->flags == MMC_DATA_WRITE)
+ meson_mmc_cmd |= CMD_CFG_DATA_WR;
+
+ cfg = CMD_CFG_DATA_IO | CMD_CFG_BLOCK_MODE | data->blocks;
+ meson_mmc_cmd |= cfg;
+ }
+
+ cfg = CMD_CFG_TIMEOUT_4S | CMD_CFG_OWNER | CMD_CFG_END_OF_CHAIN;
+ meson_mmc_cmd |= cfg;
+
+ meson_write(mmc, meson_mmc_cmd, MESON_SD_EMMC_CMD_CFG);
+}
+
+static void meson_mmc_setup_addr(struct mmc *mmc, struct mmc_data *data)
+{
+ struct meson_mmc_platdata *pdata = mmc->priv;
+ unsigned int data_size;
+ uint32_t data_addr = 0;
+
+ if (data) {
+ data_size = data->blocks * data->blocksize;
+
+ if (data->flags == MMC_DATA_READ) {
+ data_addr = (ulong) data->dest;
+ invalidate_dcache_range(data_addr,
+ data_addr + data_size);
+ } else if (data->flags == MMC_DATA_WRITE) {
+ pdata->w_buf = calloc(data_size, sizeof(char));
+ data_addr = (ulong) pdata->w_buf;
+ memcpy(pdata->w_buf, data->src, data_size);
+ flush_dcache_range(data_addr, data_addr + data_size);
+ }
+ }
+
+ meson_write(mmc, data_addr, MESON_SD_EMMC_CMD_DAT);
+}
+
+static void meson_mmc_read_response(struct mmc *mmc, struct mmc_cmd *cmd)
+{
+ if (cmd->resp_type & MMC_RSP_136) {
+ cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP3);
+ cmd->response[1] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP2);
+ cmd->response[2] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP1);
+ cmd->response[3] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
+ } else {
+ cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
+ }
+}
+
+static int meson_dm_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
+ struct mmc_data *data)
+{
+ struct mmc *mmc = mmc_get_mmc_dev(dev);
+ struct meson_mmc_platdata *pdata = mmc->priv;
+ uint32_t status;
+ ulong start;
+ int ret = 0;
+
+ /* max block size supported by chip is 512 byte */
+ if (data && data->blocksize > 512)
+ return -EINVAL;
+
+ meson_mmc_setup_cmd(mmc, data, cmd);
+ meson_mmc_setup_addr(mmc, data);
+
+ meson_write(mmc, cmd->cmdarg, MESON_SD_EMMC_CMD_ARG);
+
+ /* use 10s timeout */
+ start = get_timer(0);
+ do {
+ status = meson_read(mmc, MESON_SD_EMMC_STATUS);
+ } while(!(status & STATUS_END_OF_CHAIN) && get_timer(start) < 10000);
+
+ if (!(status & STATUS_END_OF_CHAIN))
+ ret = -ETIMEDOUT;
+ else if (status & STATUS_RESP_TIMEOUT)
+ ret = -ETIMEDOUT;
+ else if (status & STATUS_ERR_MASK)
+ ret = -EIO;
+
+ meson_mmc_read_response(mmc, cmd);
+
+ if (data && data->flags == MMC_DATA_WRITE)
+ free(pdata->w_buf);
+
+ /* reset status bits */
+ meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
+
+ return ret;
+}
+
+static const struct dm_mmc_ops meson_dm_mmc_ops = {
+ .send_cmd = meson_dm_mmc_send_cmd,
+ .set_ios = meson_dm_mmc_set_ios,
+};
+
+static int meson_mmc_ofdata_to_platdata(struct udevice *dev)
+{
+ struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
+ fdt_addr_t addr;
+
+ addr = dev_get_addr(dev);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ pdata->regbase = (void *)addr;
+
+ return 0;
+}
+
+static int meson_mmc_probe(struct udevice *dev)
+{
+ struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
+ struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
+ struct mmc *mmc = &pdata->mmc;
+ struct mmc_config *cfg = &pdata->cfg;
+ uint32_t val;
+
+ cfg->voltages = MMC_VDD_33_34 | MMC_VDD_32_33 |
+ MMC_VDD_31_32 | MMC_VDD_165_195;
+ cfg->host_caps = MMC_MODE_8BIT | MMC_MODE_4BIT |
+ MMC_MODE_HS_52MHz | MMC_MODE_HS;
+ cfg->f_min = DIV_ROUND_UP(SD_EMMC_CLKSRC_24M, CLK_MAX_DIV);
+ cfg->f_max = 100000000; /* 100 MHz */
+ cfg->b_max = 256; /* max 256 blocks */
+ cfg->name = dev->name;
+
+ mmc->priv = pdata;
+ upriv->mmc = mmc;
+
+ mmc_set_clock(mmc, cfg->f_min);
+
+ /* reset all status bits */
+ meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
+
+ /* disable interrupts */
+ meson_write(mmc, 0, MESON_SD_EMMC_IRQ_EN);
+
+ /* enable auto clock mode */
+ val = meson_read(mmc, MESON_SD_EMMC_CFG);
+ val &= ~CFG_SDCLK_ALWAYS_ON;
+ val |= CFG_AUTO_CLK;
+ meson_write(mmc, val, MESON_SD_EMMC_CFG);
+
+ return 0;
+}
+
+int meson_mmc_bind(struct udevice *dev)
+{
+ struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
+
+ return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
+}
+
+static const struct udevice_id meson_mmc_match[] = {
+ { .compatible = "amlogic,meson-gx-mmc" },
+ { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(meson_mmc) = {
+ .name = "meson_gx_mmc",
+ .id = UCLASS_MMC,
+ .of_match = meson_mmc_match,
+ .ops = &meson_dm_mmc_ops,
+ .probe = meson_mmc_probe,
+ .bind = meson_mmc_bind,
+ .ofdata_to_platdata = meson_mmc_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct meson_mmc_platdata),
+};
diff --git a/include/configs/meson-gxbb-common.h b/include/configs/meson-gxbb-common.h
index 17e81b4..b6dfbcd 100644
--- a/include/configs/meson-gxbb-common.h
+++ b/include/configs/meson-gxbb-common.h
@@ -23,6 +23,10 @@
#define CONFIG_SYS_INIT_SP_ADDR 0x20000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#endif
+
/* Generic Interrupt Controller Definitions */
#define GICD_BASE 0xc4301000
#define GICC_BASE 0xc4302000
--
2.11.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v3 3/3] odroid-c2: enable new Meson GX MMC driver in board defconfig
[not found] <f28d33f6-8c8a-c40e-1ae4-cc5f7e4f9511@gmail.com>
2017-01-27 20:55 ` [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905) Heiner Kallweit
@ 2017-01-27 20:56 ` Heiner Kallweit
2017-01-31 3:48 ` Jaehoon Chung
1 sibling, 1 reply; 7+ messages in thread
From: Heiner Kallweit @ 2017-01-27 20:56 UTC (permalink / raw)
To: u-boot
Enable new Meson GX MMC driver in Odroid C2 defconfig.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
---
v2:
- move GXBB_PINMUX definition from patch 3 to this one
v3:
- remove pinmux configuration in board init and use
pinctrl driver instead
---
configs/odroid-c2_defconfig | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/configs/odroid-c2_defconfig b/configs/odroid-c2_defconfig
index 119ab07..824dd6c 100644
--- a/configs/odroid-c2_defconfig
+++ b/configs/odroid-c2_defconfig
@@ -3,7 +3,9 @@ CONFIG_ARCH_MESON=y
CONFIG_MESON_GXBB=y
CONFIG_TARGET_ODROID_C2=y
CONFIG_IDENT_STRING=" odroid-c2"
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-odroidc2"
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -14,6 +16,7 @@ CONFIG_HUSH_PARSER=y
# CONFIG_CMD_LOADS is not set
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_MMC=y
CONFIG_OF_CONTROL=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM_ETH=y
--
2.11.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v3 3/3] odroid-c2: enable new Meson GX MMC driver in board defconfig
2017-01-27 20:56 ` [U-Boot] [PATCH v3 3/3] odroid-c2: enable new Meson GX MMC driver in board defconfig Heiner Kallweit
@ 2017-01-31 3:48 ` Jaehoon Chung
0 siblings, 0 replies; 7+ messages in thread
From: Jaehoon Chung @ 2017-01-31 3:48 UTC (permalink / raw)
To: u-boot
Hi Heiner,
On 01/28/2017 05:56 AM, Heiner Kallweit wrote:
> Enable new Meson GX MMC driver in Odroid C2 defconfig.
Conflicts this patch on latest u-boot.
Best Regards,
Jaehoon Chung
>
> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
> ---
> v2:
> - move GXBB_PINMUX definition from patch 3 to this one
> v3:
> - remove pinmux configuration in board init and use
> pinctrl driver instead
> ---
> configs/odroid-c2_defconfig | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/configs/odroid-c2_defconfig b/configs/odroid-c2_defconfig
> index 119ab07..824dd6c 100644
> --- a/configs/odroid-c2_defconfig
> +++ b/configs/odroid-c2_defconfig
> @@ -3,7 +3,9 @@ CONFIG_ARCH_MESON=y
> CONFIG_MESON_GXBB=y
> CONFIG_TARGET_ODROID_C2=y
> CONFIG_IDENT_STRING=" odroid-c2"
> -# CONFIG_MMC is not set
> +CONFIG_MMC=y
> +CONFIG_DM_MMC=y
> +CONFIG_MMC_MESON_GX=y
> CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-odroidc2"
> # CONFIG_DISPLAY_CPUINFO is not set
> # CONFIG_DISPLAY_BOARDINFO is not set
> @@ -14,6 +16,7 @@ CONFIG_HUSH_PARSER=y
> # CONFIG_CMD_LOADS is not set
> # CONFIG_CMD_FPGA is not set
> # CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_MMC=y
> CONFIG_OF_CONTROL=y
> CONFIG_NET_RANDOM_ETHADDR=y
> CONFIG_DM_ETH=y
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905)
2017-01-27 20:55 ` [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905) Heiner Kallweit
@ 2017-01-31 13:24 ` Jaehoon Chung
2017-02-02 19:10 ` Heiner Kallweit
0 siblings, 1 reply; 7+ messages in thread
From: Jaehoon Chung @ 2017-01-31 13:24 UTC (permalink / raw)
To: u-boot
On 01/28/2017 05:55 AM, Heiner Kallweit wrote:
> This driver implements MMC support on Meson GX (S905) based systems.
> It's based on Carlo Caione's work, changes:
> - BLK support added
> - general refactoring
>
> Signed-off-by: Carlo Caione <carlo@caione.org>
> Signed-off-by: Andreas F?rber <afaerber@suse.de>
> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Andreas's comment is what this patch's author is Carlo..Not just add Signed-off tag for Carlo.
When you send the email, needs to add "From: Carlo Caione <carlo@caione.org>", not yours.
> ---
> v2:
V3 should be here..not V2.
> - addressed review comments
> - general refactoring
> v3:
> - remove config symbol MMC_MESON_GX_SD_PORT
> ---
> arch/arm/include/asm/arch-meson/sd_emmc.h | 89 +++++++++
> drivers/mmc/Kconfig | 6 +
> drivers/mmc/Makefile | 1 +
> drivers/mmc/meson_gx_mmc.c | 291 ++++++++++++++++++++++++++++++
> include/configs/meson-gxbb-common.h | 4 +
> 5 files changed, 391 insertions(+)
> create mode 100644 arch/arm/include/asm/arch-meson/sd_emmc.h
> create mode 100644 drivers/mmc/meson_gx_mmc.c
>
> diff --git a/arch/arm/include/asm/arch-meson/sd_emmc.h b/arch/arm/include/asm/arch-meson/sd_emmc.h
> new file mode 100644
> index 0000000..25dbf60
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-meson/sd_emmc.h
> @@ -0,0 +1,89 @@
> +/*
> + * (C) Copyright 2017 Carlo Caione <carlo@caione.org>
I don't know Carlo already shared at github..So 2016 might be right, not 2017.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __SD_EMMC_H__
> +#define __SD_EMMC_H__
> +
> +#include <mmc.h>
> +
> +#define SDIO_PORT_A 0
> +#define SDIO_PORT_B 1
> +#define SDIO_PORT_C 2
> +
> +#define SD_EMMC_CLKSRC_24M 24000000 /* 24 MHz */
> +#define SD_EMMC_CLKSRC_DIV2 1000000000 /* 1 GHz */
> +
> +#define MESON_SD_EMMC_CLOCK 0x00
> +#define CLK_MAX_DIV 63
> +#define CLK_SRC_24M (0 << 6)
> +#define CLK_SRC_DIV2 (1 << 6)
> +#define CLK_CO_PHASE_000 (0 << 8)
> +#define CLK_CO_PHASE_090 (1 << 8)
> +#define CLK_CO_PHASE_180 (2 << 8)
> +#define CLK_CO_PHASE_270 (3 << 8)
> +#define CLK_TX_PHASE_000 (0 << 10)
> +#define CLK_TX_PHASE_090 (1 << 10)
> +#define CLK_TX_PHASE_180 (2 << 10)
> +#define CLK_TX_PHASE_270 (3 << 10)
> +#define CLK_ALWAYS_ON BIT(24)
> +
> +#define MESON_SD_EMMC_CFG 0x44
> +#define CFG_BUS_WIDTH_MASK GENMASK(1, 0)
> +#define CFG_BUS_WIDTH_1 0
> +#define CFG_BUS_WIDTH_4 1
> +#define CFG_BUS_WIDTH_8 2
> +#define CFG_BL_LEN_MASK GENMASK(7, 4)
> +#define CFG_BL_LEN_SHIFT 4
> +#define CFG_BL_LEN_512 (9 << 4)
> +#define CFG_RESP_TIMEOUT_MASK GENMASK(11, 8)
> +#define CFG_RESP_TIMEOUT_256 (8 << 8)
> +#define CFG_RC_CC_MASK GENMASK(15, 12)
> +#define CFG_RC_CC_16 (4 << 12)
> +#define CFG_SDCLK_ALWAYS_ON BIT(18)
> +#define CFG_AUTO_CLK BIT(23)
> +
> +#define MESON_SD_EMMC_STATUS 0x48
> +#define STATUS_MASK GENMASK(15, 0)
> +#define STATUS_ERR_MASK GENMASK(12, 0)
> +#define STATUS_RXD_ERR_MASK GENMASK(7, 0)
> +#define STATUS_TXD_ERR BIT(8)
> +#define STATUS_DESC_ERR BIT(9)
> +#define STATUS_RESP_ERR BIT(10)
> +#define STATUS_RESP_TIMEOUT BIT(11)
> +#define STATUS_DESC_TIMEOUT BIT(12)
> +#define STATUS_END_OF_CHAIN BIT(13)
> +
> +#define MESON_SD_EMMC_IRQ_EN 0x4c
> +
> +#define MESON_SD_EMMC_CMD_CFG 0x50
> +#define CMD_CFG_LENGTH_MASK GENMASK(8, 0)
> +#define CMD_CFG_BLOCK_MODE BIT(9)
> +#define CMD_CFG_R1B BIT(10)
> +#define CMD_CFG_END_OF_CHAIN BIT(11)
> +#define CMD_CFG_TIMEOUT_4S (12 << 12)
> +#define CMD_CFG_NO_RESP BIT(16)
> +#define CMD_CFG_DATA_IO BIT(18)
> +#define CMD_CFG_DATA_WR BIT(19)
> +#define CMD_CFG_RESP_NOCRC BIT(20)
> +#define CMD_CFG_RESP_128 BIT(21)
> +#define CMD_CFG_CMD_INDEX_SHIFT 24
> +#define CMD_CFG_OWNER BIT(31)
> +
> +#define MESON_SD_EMMC_CMD_ARG 0x54
> +#define MESON_SD_EMMC_CMD_DAT 0x58
> +#define MESON_SD_EMMC_CMD_RSP 0x5c
> +#define MESON_SD_EMMC_CMD_RSP1 0x60
> +#define MESON_SD_EMMC_CMD_RSP2 0x64
> +#define MESON_SD_EMMC_CMD_RSP3 0x68
> +
> +struct meson_mmc_platdata {
> + struct mmc_config cfg;
> + struct mmc mmc;
> + void *regbase;
> + void *w_buf;
> +};
> +
> +#endif
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index 147e52d..ffae684 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -168,6 +168,12 @@ config ZYNQ_SDHCI
> help
> Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform
>
> +config MMC_MESON_GX
> + bool "Meson GX EMMC controller support"
> + depends on DM_MMC && BLK && DM_MMC_OPS && ARCH_MESON
> + help
> + Support for EMMC host controller on Meson GX ARM SoCs platform (S905)
> +
> config ROCKCHIP_SDHCI
> bool "Arasan SDHCI controller for Rockchip support"
> depends on DM_MMC && BLK && DM_MMC_OPS
> diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
> index 6af7f79..baa6531 100644
> --- a/drivers/mmc/Makefile
> +++ b/drivers/mmc/Makefile
> @@ -31,6 +31,7 @@ ifdef CONFIG_SUPPORT_EMMC_BOOT
> obj-$(CONFIG_GENERIC_MMC) += mmc_boot.o
> endif
> obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o
> +obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o
> obj-$(CONFIG_MMC_SPI) += mmc_spi.o
> obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o
> obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o
> diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
> new file mode 100644
> index 0000000..612a81e
> --- /dev/null
> +++ b/drivers/mmc/meson_gx_mmc.c
> @@ -0,0 +1,291 @@
> +/*
> + * (C) Copyright 2017 Carlo Caione <carlo@caione.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <fdtdec.h>
> +#include <malloc.h>
> +#include <mmc.h>
> +#include <asm/io.h>
> +#include <asm/arch/sd_emmc.h>
> +#include <dm/device.h>
> +#include <linux/log2.h>
> +
> +static inline void *get_regbase(const struct mmc *mmc)
> +{
> + struct meson_mmc_platdata *pdata = mmc->priv;
> +
> + return pdata->regbase;
> +}
> +
> +static inline uint32_t meson_read(struct mmc *mmc, int offset)
> +{
> + return readl(get_regbase(mmc) + offset);
> +}
> +
> +static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
> +{
> + writel(val, get_regbase(mmc) + offset);
> +}
> +
> +static void meson_mmc_config_clock(struct mmc *mmc)
> +{
> + uint32_t meson_mmc_clk = 0;
> + unsigned int clk, clk_src, clk_div;
> +
> + /* 1GHz / CLK_MAX_DIV = 15,9 MHz */
> + if (mmc->clock > 16000000) {
> + clk = SD_EMMC_CLKSRC_DIV2;
> + clk_src = CLK_SRC_DIV2;
> + } else {
> + clk = SD_EMMC_CLKSRC_24M;
> + clk_src = CLK_SRC_24M;
> + }
> + clk_div = DIV_ROUND_UP(clk, mmc->clock);
> +
> + /* 180 phase core clock */
> + meson_mmc_clk |= CLK_CO_PHASE_180;
> +
> + /* 180 phase tx clock */
> + meson_mmc_clk |= CLK_TX_PHASE_180;
> +
> + /* clock settings */
> + meson_mmc_clk |= clk_src;
> + meson_mmc_clk |= clk_div;
> +
> + meson_write(mmc, meson_mmc_clk, MESON_SD_EMMC_CLOCK);
> +}
> +
> +static int meson_dm_mmc_set_ios(struct udevice *dev)
> +{
> + struct mmc *mmc = mmc_get_mmc_dev(dev);
> + uint32_t meson_mmc_cfg;
> +
> + meson_mmc_config_clock(mmc);
> +
> + meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
> +
> + meson_mmc_cfg &= ~CFG_BUS_WIDTH_MASK;
> + if (mmc->bus_width == 1)
> + meson_mmc_cfg |= CFG_BUS_WIDTH_1;
> + else if (mmc->bus_width == 4)
> + meson_mmc_cfg |= CFG_BUS_WIDTH_4;
> + else if (mmc->bus_width == 8)
> + meson_mmc_cfg |= CFG_BUS_WIDTH_8;
> + else
> + return -EINVAL;
> +
> + /* 512 bytes block length */
> + meson_mmc_cfg &= ~CFG_BL_LEN_MASK;
> + meson_mmc_cfg |= CFG_BL_LEN_512;
> +
> + /* Response timeout 256 clk */
> + meson_mmc_cfg &= ~CFG_RESP_TIMEOUT_MASK;
> + meson_mmc_cfg |= CFG_RESP_TIMEOUT_256;
> +
> + /* Command-command gap 16 clk */
> + meson_mmc_cfg &= ~CFG_RC_CC_MASK;
> + meson_mmc_cfg |= CFG_RC_CC_16;
> +
> + meson_write(mmc, meson_mmc_cfg, MESON_SD_EMMC_CFG);
> +
> + return 0;
> +}
> +
> +static void meson_mmc_setup_cmd(struct mmc *mmc, struct mmc_data *data,
> + struct mmc_cmd *cmd)
> +{
> + uint32_t meson_mmc_cmd = 0, cfg;
> +
> + meson_mmc_cmd |= cmd->cmdidx << CMD_CFG_CMD_INDEX_SHIFT;
> +
> + if (cmd->resp_type & MMC_RSP_PRESENT) {
> + if (cmd->resp_type & MMC_RSP_136)
> + meson_mmc_cmd |= CMD_CFG_RESP_128;
> +
> + if (cmd->resp_type & MMC_RSP_BUSY)
> + meson_mmc_cmd |= CMD_CFG_R1B;
> +
> + if (!(cmd->resp_type & MMC_RSP_CRC))
> + meson_mmc_cmd |= CMD_CFG_RESP_NOCRC;
> + } else {
> + meson_mmc_cmd |= CMD_CFG_NO_RESP;
> + }
> +
> + if (data) {
> + cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
> + cfg &= ~CFG_BL_LEN_MASK;
> + cfg |= ilog2(data->blocksize) << CFG_BL_LEN_SHIFT;
> + meson_write(mmc, cfg, MESON_SD_EMMC_CFG);
> +
> + if (data->flags == MMC_DATA_WRITE)
> + meson_mmc_cmd |= CMD_CFG_DATA_WR;
> +
> + cfg = CMD_CFG_DATA_IO | CMD_CFG_BLOCK_MODE | data->blocks;
> + meson_mmc_cmd |= cfg;
> + }
> +
> + cfg = CMD_CFG_TIMEOUT_4S | CMD_CFG_OWNER | CMD_CFG_END_OF_CHAIN;
> + meson_mmc_cmd |= cfg;
> +
> + meson_write(mmc, meson_mmc_cmd, MESON_SD_EMMC_CMD_CFG);
> +}
> +
> +static void meson_mmc_setup_addr(struct mmc *mmc, struct mmc_data *data)
> +{
> + struct meson_mmc_platdata *pdata = mmc->priv;
> + unsigned int data_size;
> + uint32_t data_addr = 0;
> +
> + if (data) {
> + data_size = data->blocks * data->blocksize;
> +
> + if (data->flags == MMC_DATA_READ) {
> + data_addr = (ulong) data->dest;
> + invalidate_dcache_range(data_addr,
> + data_addr + data_size);
> + } else if (data->flags == MMC_DATA_WRITE) {
> + pdata->w_buf = calloc(data_size, sizeof(char));
> + data_addr = (ulong) pdata->w_buf;
> + memcpy(pdata->w_buf, data->src, data_size);
> + flush_dcache_range(data_addr, data_addr + data_size);
> + }
> + }
> +
> + meson_write(mmc, data_addr, MESON_SD_EMMC_CMD_DAT);
> +}
> +
> +static void meson_mmc_read_response(struct mmc *mmc, struct mmc_cmd *cmd)
> +{
> + if (cmd->resp_type & MMC_RSP_136) {
> + cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP3);
> + cmd->response[1] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP2);
> + cmd->response[2] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP1);
> + cmd->response[3] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
> + } else {
> + cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
> + }
> +}
> +
> +static int meson_dm_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
> + struct mmc_data *data)
> +{
> + struct mmc *mmc = mmc_get_mmc_dev(dev);
> + struct meson_mmc_platdata *pdata = mmc->priv;
> + uint32_t status;
> + ulong start;
> + int ret = 0;
> +
> + /* max block size supported by chip is 512 byte */
> + if (data && data->blocksize > 512)
> + return -EINVAL;
> +
> + meson_mmc_setup_cmd(mmc, data, cmd);
> + meson_mmc_setup_addr(mmc, data);
> +
> + meson_write(mmc, cmd->cmdarg, MESON_SD_EMMC_CMD_ARG);
> +
> + /* use 10s timeout */
> + start = get_timer(0);
> + do {
> + status = meson_read(mmc, MESON_SD_EMMC_STATUS);
> + } while(!(status & STATUS_END_OF_CHAIN) && get_timer(start) < 10000);
> +
> + if (!(status & STATUS_END_OF_CHAIN))
> + ret = -ETIMEDOUT;
> + else if (status & STATUS_RESP_TIMEOUT)
> + ret = -ETIMEDOUT;
> + else if (status & STATUS_ERR_MASK)
> + ret = -EIO;
> +
> + meson_mmc_read_response(mmc, cmd);
> +
> + if (data && data->flags == MMC_DATA_WRITE)
> + free(pdata->w_buf);
> +
> + /* reset status bits */
> + meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
> +
> + return ret;
> +}
> +
> +static const struct dm_mmc_ops meson_dm_mmc_ops = {
> + .send_cmd = meson_dm_mmc_send_cmd,
> + .set_ios = meson_dm_mmc_set_ios,
> +};
> +
> +static int meson_mmc_ofdata_to_platdata(struct udevice *dev)
> +{
> + struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
> + fdt_addr_t addr;
> +
> + addr = dev_get_addr(dev);
> + if (addr == FDT_ADDR_T_NONE)
> + return -EINVAL;
> +
> + pdata->regbase = (void *)addr;
> +
> + return 0;
> +}
> +
> +static int meson_mmc_probe(struct udevice *dev)
> +{
> + struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
> + struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
> + struct mmc *mmc = &pdata->mmc;
> + struct mmc_config *cfg = &pdata->cfg;
> + uint32_t val;
> +
> + cfg->voltages = MMC_VDD_33_34 | MMC_VDD_32_33 |
> + MMC_VDD_31_32 | MMC_VDD_165_195;
> + cfg->host_caps = MMC_MODE_8BIT | MMC_MODE_4BIT |
> + MMC_MODE_HS_52MHz | MMC_MODE_HS;
> + cfg->f_min = DIV_ROUND_UP(SD_EMMC_CLKSRC_24M, CLK_MAX_DIV);
> + cfg->f_max = 100000000; /* 100 MHz */
> + cfg->b_max = 256; /* max 256 blocks */
> + cfg->name = dev->name;
> +
> + mmc->priv = pdata;
> + upriv->mmc = mmc;
> +
> + mmc_set_clock(mmc, cfg->f_min);
> +
> + /* reset all status bits */
> + meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
> +
> + /* disable interrupts */
> + meson_write(mmc, 0, MESON_SD_EMMC_IRQ_EN);
> +
> + /* enable auto clock mode */
> + val = meson_read(mmc, MESON_SD_EMMC_CFG);
> + val &= ~CFG_SDCLK_ALWAYS_ON;
> + val |= CFG_AUTO_CLK;
> + meson_write(mmc, val, MESON_SD_EMMC_CFG);
> +
> + return 0;
> +}
> +
> +int meson_mmc_bind(struct udevice *dev)
> +{
> + struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
> +
> + return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
> +}
> +
> +static const struct udevice_id meson_mmc_match[] = {
> + { .compatible = "amlogic,meson-gx-mmc" },
> + { /* sentinel */ }
> +};
> +
> +U_BOOT_DRIVER(meson_mmc) = {
> + .name = "meson_gx_mmc",
> + .id = UCLASS_MMC,
> + .of_match = meson_mmc_match,
> + .ops = &meson_dm_mmc_ops,
> + .probe = meson_mmc_probe,
> + .bind = meson_mmc_bind,
> + .ofdata_to_platdata = meson_mmc_ofdata_to_platdata,
> + .platdata_auto_alloc_size = sizeof(struct meson_mmc_platdata),
> +};
> diff --git a/include/configs/meson-gxbb-common.h b/include/configs/meson-gxbb-common.h
> index 17e81b4..b6dfbcd 100644
> --- a/include/configs/meson-gxbb-common.h
> +++ b/include/configs/meson-gxbb-common.h
> @@ -23,6 +23,10 @@
> #define CONFIG_SYS_INIT_SP_ADDR 0x20000000
> #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_TEXT_BASE
>
> +#ifdef CONFIG_MMC
> +#define CONFIG_GENERIC_MMC
> +#endif
> +
> /* Generic Interrupt Controller Definitions */
> #define GICD_BASE 0xc4301000
> #define GICC_BASE 0xc4302000
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905)
2017-01-31 13:24 ` Jaehoon Chung
@ 2017-02-02 19:10 ` Heiner Kallweit
[not found] ` <20170202193351.GB6393@excalibur.cnev.de>
0 siblings, 1 reply; 7+ messages in thread
From: Heiner Kallweit @ 2017-02-02 19:10 UTC (permalink / raw)
To: u-boot
Am 31.01.2017 um 14:24 schrieb Jaehoon Chung:
> On 01/28/2017 05:55 AM, Heiner Kallweit wrote:
>> This driver implements MMC support on Meson GX (S905) based systems.
>> It's based on Carlo Caione's work, changes:
>> - BLK support added
>> - general refactoring
>>
>> Signed-off-by: Carlo Caione <carlo@caione.org>
>> Signed-off-by: Andreas F?rber <afaerber@suse.de>
>> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
>
> Andreas's comment is what this patch's author is Carlo..Not just add Signed-off tag for Carlo.
>
> When you send the email, needs to add "From: Carlo Caione <carlo@caione.org>", not yours.
>
I sent a v4 series addressing the review comments.
I tried sending patch 2 with Carlo as "From:", however the mail provider replaced this with
my default mail address.
I checked with my other mail providers, they also allow only sender addresses belonging to me.
>
>> ---
>> v2:
>
> V3 should be here..not V2.
>
>> - addressed review comments
>> - general refactoring
>> v3:
>> - remove config symbol MMC_MESON_GX_SD_PORT
>> ---
>> arch/arm/include/asm/arch-meson/sd_emmc.h | 89 +++++++++
>> drivers/mmc/Kconfig | 6 +
>> drivers/mmc/Makefile | 1 +
>> drivers/mmc/meson_gx_mmc.c | 291 ++++++++++++++++++++++++++++++
>> include/configs/meson-gxbb-common.h | 4 +
>> 5 files changed, 391 insertions(+)
>> create mode 100644 arch/arm/include/asm/arch-meson/sd_emmc.h
>> create mode 100644 drivers/mmc/meson_gx_mmc.c
>>
>> diff --git a/arch/arm/include/asm/arch-meson/sd_emmc.h b/arch/arm/include/asm/arch-meson/sd_emmc.h
>> new file mode 100644
>> index 0000000..25dbf60
>> --- /dev/null
>> +++ b/arch/arm/include/asm/arch-meson/sd_emmc.h
>> @@ -0,0 +1,89 @@
>> +/*
>> + * (C) Copyright 2017 Carlo Caione <carlo@caione.org>
>
> I don't know Carlo already shared at github..So 2016 might be right, not 2017.
>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#ifndef __SD_EMMC_H__
>> +#define __SD_EMMC_H__
>> +
>> +#include <mmc.h>
>> +
>> +#define SDIO_PORT_A 0
>> +#define SDIO_PORT_B 1
>> +#define SDIO_PORT_C 2
>> +
>> +#define SD_EMMC_CLKSRC_24M 24000000 /* 24 MHz */
>> +#define SD_EMMC_CLKSRC_DIV2 1000000000 /* 1 GHz */
>> +
>> +#define MESON_SD_EMMC_CLOCK 0x00
>> +#define CLK_MAX_DIV 63
>> +#define CLK_SRC_24M (0 << 6)
>> +#define CLK_SRC_DIV2 (1 << 6)
>> +#define CLK_CO_PHASE_000 (0 << 8)
>> +#define CLK_CO_PHASE_090 (1 << 8)
>> +#define CLK_CO_PHASE_180 (2 << 8)
>> +#define CLK_CO_PHASE_270 (3 << 8)
>> +#define CLK_TX_PHASE_000 (0 << 10)
>> +#define CLK_TX_PHASE_090 (1 << 10)
>> +#define CLK_TX_PHASE_180 (2 << 10)
>> +#define CLK_TX_PHASE_270 (3 << 10)
>> +#define CLK_ALWAYS_ON BIT(24)
>> +
>> +#define MESON_SD_EMMC_CFG 0x44
>> +#define CFG_BUS_WIDTH_MASK GENMASK(1, 0)
>> +#define CFG_BUS_WIDTH_1 0
>> +#define CFG_BUS_WIDTH_4 1
>> +#define CFG_BUS_WIDTH_8 2
>> +#define CFG_BL_LEN_MASK GENMASK(7, 4)
>> +#define CFG_BL_LEN_SHIFT 4
>> +#define CFG_BL_LEN_512 (9 << 4)
>> +#define CFG_RESP_TIMEOUT_MASK GENMASK(11, 8)
>> +#define CFG_RESP_TIMEOUT_256 (8 << 8)
>> +#define CFG_RC_CC_MASK GENMASK(15, 12)
>> +#define CFG_RC_CC_16 (4 << 12)
>> +#define CFG_SDCLK_ALWAYS_ON BIT(18)
>> +#define CFG_AUTO_CLK BIT(23)
>> +
>> +#define MESON_SD_EMMC_STATUS 0x48
>> +#define STATUS_MASK GENMASK(15, 0)
>> +#define STATUS_ERR_MASK GENMASK(12, 0)
>> +#define STATUS_RXD_ERR_MASK GENMASK(7, 0)
>> +#define STATUS_TXD_ERR BIT(8)
>> +#define STATUS_DESC_ERR BIT(9)
>> +#define STATUS_RESP_ERR BIT(10)
>> +#define STATUS_RESP_TIMEOUT BIT(11)
>> +#define STATUS_DESC_TIMEOUT BIT(12)
>> +#define STATUS_END_OF_CHAIN BIT(13)
>> +
>> +#define MESON_SD_EMMC_IRQ_EN 0x4c
>> +
>> +#define MESON_SD_EMMC_CMD_CFG 0x50
>> +#define CMD_CFG_LENGTH_MASK GENMASK(8, 0)
>> +#define CMD_CFG_BLOCK_MODE BIT(9)
>> +#define CMD_CFG_R1B BIT(10)
>> +#define CMD_CFG_END_OF_CHAIN BIT(11)
>> +#define CMD_CFG_TIMEOUT_4S (12 << 12)
>> +#define CMD_CFG_NO_RESP BIT(16)
>> +#define CMD_CFG_DATA_IO BIT(18)
>> +#define CMD_CFG_DATA_WR BIT(19)
>> +#define CMD_CFG_RESP_NOCRC BIT(20)
>> +#define CMD_CFG_RESP_128 BIT(21)
>> +#define CMD_CFG_CMD_INDEX_SHIFT 24
>> +#define CMD_CFG_OWNER BIT(31)
>> +
>> +#define MESON_SD_EMMC_CMD_ARG 0x54
>> +#define MESON_SD_EMMC_CMD_DAT 0x58
>> +#define MESON_SD_EMMC_CMD_RSP 0x5c
>> +#define MESON_SD_EMMC_CMD_RSP1 0x60
>> +#define MESON_SD_EMMC_CMD_RSP2 0x64
>> +#define MESON_SD_EMMC_CMD_RSP3 0x68
>> +
>> +struct meson_mmc_platdata {
>> + struct mmc_config cfg;
>> + struct mmc mmc;
>> + void *regbase;
>> + void *w_buf;
>> +};
>> +
>> +#endif
>> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
>> index 147e52d..ffae684 100644
>> --- a/drivers/mmc/Kconfig
>> +++ b/drivers/mmc/Kconfig
>> @@ -168,6 +168,12 @@ config ZYNQ_SDHCI
>> help
>> Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform
>>
>> +config MMC_MESON_GX
>> + bool "Meson GX EMMC controller support"
>> + depends on DM_MMC && BLK && DM_MMC_OPS && ARCH_MESON
>> + help
>> + Support for EMMC host controller on Meson GX ARM SoCs platform (S905)
>> +
>> config ROCKCHIP_SDHCI
>> bool "Arasan SDHCI controller for Rockchip support"
>> depends on DM_MMC && BLK && DM_MMC_OPS
>> diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
>> index 6af7f79..baa6531 100644
>> --- a/drivers/mmc/Makefile
>> +++ b/drivers/mmc/Makefile
>> @@ -31,6 +31,7 @@ ifdef CONFIG_SUPPORT_EMMC_BOOT
>> obj-$(CONFIG_GENERIC_MMC) += mmc_boot.o
>> endif
>> obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o
>> +obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o
>> obj-$(CONFIG_MMC_SPI) += mmc_spi.o
>> obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o
>> obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o
>> diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
>> new file mode 100644
>> index 0000000..612a81e
>> --- /dev/null
>> +++ b/drivers/mmc/meson_gx_mmc.c
>> @@ -0,0 +1,291 @@
>> +/*
>> + * (C) Copyright 2017 Carlo Caione <carlo@caione.org>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <fdtdec.h>
>> +#include <malloc.h>
>> +#include <mmc.h>
>> +#include <asm/io.h>
>> +#include <asm/arch/sd_emmc.h>
>> +#include <dm/device.h>
>> +#include <linux/log2.h>
>> +
>> +static inline void *get_regbase(const struct mmc *mmc)
>> +{
>> + struct meson_mmc_platdata *pdata = mmc->priv;
>> +
>> + return pdata->regbase;
>> +}
>> +
>> +static inline uint32_t meson_read(struct mmc *mmc, int offset)
>> +{
>> + return readl(get_regbase(mmc) + offset);
>> +}
>> +
>> +static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
>> +{
>> + writel(val, get_regbase(mmc) + offset);
>> +}
>> +
>> +static void meson_mmc_config_clock(struct mmc *mmc)
>> +{
>> + uint32_t meson_mmc_clk = 0;
>> + unsigned int clk, clk_src, clk_div;
>> +
>> + /* 1GHz / CLK_MAX_DIV = 15,9 MHz */
>> + if (mmc->clock > 16000000) {
>> + clk = SD_EMMC_CLKSRC_DIV2;
>> + clk_src = CLK_SRC_DIV2;
>> + } else {
>> + clk = SD_EMMC_CLKSRC_24M;
>> + clk_src = CLK_SRC_24M;
>> + }
>> + clk_div = DIV_ROUND_UP(clk, mmc->clock);
>> +
>> + /* 180 phase core clock */
>> + meson_mmc_clk |= CLK_CO_PHASE_180;
>> +
>> + /* 180 phase tx clock */
>> + meson_mmc_clk |= CLK_TX_PHASE_180;
>> +
>> + /* clock settings */
>> + meson_mmc_clk |= clk_src;
>> + meson_mmc_clk |= clk_div;
>> +
>> + meson_write(mmc, meson_mmc_clk, MESON_SD_EMMC_CLOCK);
>> +}
>> +
>> +static int meson_dm_mmc_set_ios(struct udevice *dev)
>> +{
>> + struct mmc *mmc = mmc_get_mmc_dev(dev);
>> + uint32_t meson_mmc_cfg;
>> +
>> + meson_mmc_config_clock(mmc);
>> +
>> + meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
>> +
>> + meson_mmc_cfg &= ~CFG_BUS_WIDTH_MASK;
>> + if (mmc->bus_width == 1)
>> + meson_mmc_cfg |= CFG_BUS_WIDTH_1;
>> + else if (mmc->bus_width == 4)
>> + meson_mmc_cfg |= CFG_BUS_WIDTH_4;
>> + else if (mmc->bus_width == 8)
>> + meson_mmc_cfg |= CFG_BUS_WIDTH_8;
>> + else
>> + return -EINVAL;
>> +
>> + /* 512 bytes block length */
>> + meson_mmc_cfg &= ~CFG_BL_LEN_MASK;
>> + meson_mmc_cfg |= CFG_BL_LEN_512;
>> +
>> + /* Response timeout 256 clk */
>> + meson_mmc_cfg &= ~CFG_RESP_TIMEOUT_MASK;
>> + meson_mmc_cfg |= CFG_RESP_TIMEOUT_256;
>> +
>> + /* Command-command gap 16 clk */
>> + meson_mmc_cfg &= ~CFG_RC_CC_MASK;
>> + meson_mmc_cfg |= CFG_RC_CC_16;
>> +
>> + meson_write(mmc, meson_mmc_cfg, MESON_SD_EMMC_CFG);
>> +
>> + return 0;
>> +}
>> +
>> +static void meson_mmc_setup_cmd(struct mmc *mmc, struct mmc_data *data,
>> + struct mmc_cmd *cmd)
>> +{
>> + uint32_t meson_mmc_cmd = 0, cfg;
>> +
>> + meson_mmc_cmd |= cmd->cmdidx << CMD_CFG_CMD_INDEX_SHIFT;
>> +
>> + if (cmd->resp_type & MMC_RSP_PRESENT) {
>> + if (cmd->resp_type & MMC_RSP_136)
>> + meson_mmc_cmd |= CMD_CFG_RESP_128;
>> +
>> + if (cmd->resp_type & MMC_RSP_BUSY)
>> + meson_mmc_cmd |= CMD_CFG_R1B;
>> +
>> + if (!(cmd->resp_type & MMC_RSP_CRC))
>> + meson_mmc_cmd |= CMD_CFG_RESP_NOCRC;
>> + } else {
>> + meson_mmc_cmd |= CMD_CFG_NO_RESP;
>> + }
>> +
>> + if (data) {
>> + cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
>> + cfg &= ~CFG_BL_LEN_MASK;
>> + cfg |= ilog2(data->blocksize) << CFG_BL_LEN_SHIFT;
>> + meson_write(mmc, cfg, MESON_SD_EMMC_CFG);
>> +
>> + if (data->flags == MMC_DATA_WRITE)
>> + meson_mmc_cmd |= CMD_CFG_DATA_WR;
>> +
>> + cfg = CMD_CFG_DATA_IO | CMD_CFG_BLOCK_MODE | data->blocks;
>> + meson_mmc_cmd |= cfg;
>> + }
>> +
>> + cfg = CMD_CFG_TIMEOUT_4S | CMD_CFG_OWNER | CMD_CFG_END_OF_CHAIN;
>> + meson_mmc_cmd |= cfg;
>> +
>> + meson_write(mmc, meson_mmc_cmd, MESON_SD_EMMC_CMD_CFG);
>> +}
>> +
>> +static void meson_mmc_setup_addr(struct mmc *mmc, struct mmc_data *data)
>> +{
>> + struct meson_mmc_platdata *pdata = mmc->priv;
>> + unsigned int data_size;
>> + uint32_t data_addr = 0;
>> +
>> + if (data) {
>> + data_size = data->blocks * data->blocksize;
>> +
>> + if (data->flags == MMC_DATA_READ) {
>> + data_addr = (ulong) data->dest;
>> + invalidate_dcache_range(data_addr,
>> + data_addr + data_size);
>> + } else if (data->flags == MMC_DATA_WRITE) {
>> + pdata->w_buf = calloc(data_size, sizeof(char));
>> + data_addr = (ulong) pdata->w_buf;
>> + memcpy(pdata->w_buf, data->src, data_size);
>> + flush_dcache_range(data_addr, data_addr + data_size);
>> + }
>> + }
>> +
>> + meson_write(mmc, data_addr, MESON_SD_EMMC_CMD_DAT);
>> +}
>> +
>> +static void meson_mmc_read_response(struct mmc *mmc, struct mmc_cmd *cmd)
>> +{
>> + if (cmd->resp_type & MMC_RSP_136) {
>> + cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP3);
>> + cmd->response[1] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP2);
>> + cmd->response[2] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP1);
>> + cmd->response[3] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
>> + } else {
>> + cmd->response[0] = meson_read(mmc, MESON_SD_EMMC_CMD_RSP);
>> + }
>> +}
>> +
>> +static int meson_dm_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
>> + struct mmc_data *data)
>> +{
>> + struct mmc *mmc = mmc_get_mmc_dev(dev);
>> + struct meson_mmc_platdata *pdata = mmc->priv;
>> + uint32_t status;
>> + ulong start;
>> + int ret = 0;
>> +
>> + /* max block size supported by chip is 512 byte */
>> + if (data && data->blocksize > 512)
>> + return -EINVAL;
>> +
>> + meson_mmc_setup_cmd(mmc, data, cmd);
>> + meson_mmc_setup_addr(mmc, data);
>> +
>> + meson_write(mmc, cmd->cmdarg, MESON_SD_EMMC_CMD_ARG);
>> +
>> + /* use 10s timeout */
>> + start = get_timer(0);
>> + do {
>> + status = meson_read(mmc, MESON_SD_EMMC_STATUS);
>> + } while(!(status & STATUS_END_OF_CHAIN) && get_timer(start) < 10000);
>> +
>> + if (!(status & STATUS_END_OF_CHAIN))
>> + ret = -ETIMEDOUT;
>> + else if (status & STATUS_RESP_TIMEOUT)
>> + ret = -ETIMEDOUT;
>> + else if (status & STATUS_ERR_MASK)
>> + ret = -EIO;
>> +
>> + meson_mmc_read_response(mmc, cmd);
>> +
>> + if (data && data->flags == MMC_DATA_WRITE)
>> + free(pdata->w_buf);
>> +
>> + /* reset status bits */
>> + meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct dm_mmc_ops meson_dm_mmc_ops = {
>> + .send_cmd = meson_dm_mmc_send_cmd,
>> + .set_ios = meson_dm_mmc_set_ios,
>> +};
>> +
>> +static int meson_mmc_ofdata_to_platdata(struct udevice *dev)
>> +{
>> + struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
>> + fdt_addr_t addr;
>> +
>> + addr = dev_get_addr(dev);
>> + if (addr == FDT_ADDR_T_NONE)
>> + return -EINVAL;
>> +
>> + pdata->regbase = (void *)addr;
>> +
>> + return 0;
>> +}
>> +
>> +static int meson_mmc_probe(struct udevice *dev)
>> +{
>> + struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
>> + struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
>> + struct mmc *mmc = &pdata->mmc;
>> + struct mmc_config *cfg = &pdata->cfg;
>> + uint32_t val;
>> +
>> + cfg->voltages = MMC_VDD_33_34 | MMC_VDD_32_33 |
>> + MMC_VDD_31_32 | MMC_VDD_165_195;
>> + cfg->host_caps = MMC_MODE_8BIT | MMC_MODE_4BIT |
>> + MMC_MODE_HS_52MHz | MMC_MODE_HS;
>> + cfg->f_min = DIV_ROUND_UP(SD_EMMC_CLKSRC_24M, CLK_MAX_DIV);
>> + cfg->f_max = 100000000; /* 100 MHz */
>> + cfg->b_max = 256; /* max 256 blocks */
>> + cfg->name = dev->name;
>> +
>> + mmc->priv = pdata;
>> + upriv->mmc = mmc;
>> +
>> + mmc_set_clock(mmc, cfg->f_min);
>> +
>> + /* reset all status bits */
>> + meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
>> +
>> + /* disable interrupts */
>> + meson_write(mmc, 0, MESON_SD_EMMC_IRQ_EN);
>> +
>> + /* enable auto clock mode */
>> + val = meson_read(mmc, MESON_SD_EMMC_CFG);
>> + val &= ~CFG_SDCLK_ALWAYS_ON;
>> + val |= CFG_AUTO_CLK;
>> + meson_write(mmc, val, MESON_SD_EMMC_CFG);
>> +
>> + return 0;
>> +}
>> +
>> +int meson_mmc_bind(struct udevice *dev)
>> +{
>> + struct meson_mmc_platdata *pdata = dev_get_platdata(dev);
>> +
>> + return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
>> +}
>> +
>> +static const struct udevice_id meson_mmc_match[] = {
>> + { .compatible = "amlogic,meson-gx-mmc" },
>> + { /* sentinel */ }
>> +};
>> +
>> +U_BOOT_DRIVER(meson_mmc) = {
>> + .name = "meson_gx_mmc",
>> + .id = UCLASS_MMC,
>> + .of_match = meson_mmc_match,
>> + .ops = &meson_dm_mmc_ops,
>> + .probe = meson_mmc_probe,
>> + .bind = meson_mmc_bind,
>> + .ofdata_to_platdata = meson_mmc_ofdata_to_platdata,
>> + .platdata_auto_alloc_size = sizeof(struct meson_mmc_platdata),
>> +};
>> diff --git a/include/configs/meson-gxbb-common.h b/include/configs/meson-gxbb-common.h
>> index 17e81b4..b6dfbcd 100644
>> --- a/include/configs/meson-gxbb-common.h
>> +++ b/include/configs/meson-gxbb-common.h
>> @@ -23,6 +23,10 @@
>> #define CONFIG_SYS_INIT_SP_ADDR 0x20000000
>> #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_TEXT_BASE
>>
>> +#ifdef CONFIG_MMC
>> +#define CONFIG_GENERIC_MMC
>> +#endif
>> +
>> /* Generic Interrupt Controller Definitions */
>> #define GICD_BASE 0xc4301000
>> #define GICC_BASE 0xc4302000
>>
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905)
[not found] ` <20170202193351.GB6393@excalibur.cnev.de>
@ 2017-02-02 19:41 ` Heiner Kallweit
2017-02-02 20:21 ` Andreas Färber
0 siblings, 1 reply; 7+ messages in thread
From: Heiner Kallweit @ 2017-02-02 19:41 UTC (permalink / raw)
To: u-boot
Am 02.02.2017 um 20:33 schrieb Karsten Merker:
> On Thu, Feb 02, 2017 at 08:10:54PM +0100, Heiner Kallweit wrote:
>> Am 31.01.2017 um 14:24 schrieb Jaehoon Chung:
>>> On 01/28/2017 05:55 AM, Heiner Kallweit wrote:
>>>> This driver implements MMC support on Meson GX (S905) based systems.
>>>> It's based on Carlo Caione's work, changes:
>>>> - BLK support added
>>>> - general refactoring
>>>>
>>>> Signed-off-by: Carlo Caione <carlo@caione.org>
>>>> Signed-off-by: Andreas F?rber <afaerber@suse.de>
>>>> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
>>>
>>> Andreas's comment is what this patch's author is Carlo..Not
>>> just add Signed-off tag for Carlo.
>>>
>>> When you send the email, needs to add "From: Carlo Caione
>>> <carlo@caione.org>", not yours.
>>>
>> I sent a v4 series addressing the review comments.
>> I tried sending patch 2 with Carlo as "From:", however the mail
>> provider replaced this with my default mail address.
>> I checked with my other mail providers, they also allow only
>> sender addresses belonging to me.
>
> IIRC putting "From: Carlo Caione <carlo@caione.org>" as the
> first line in the commit log makes git set the patch author
> accordingly during "git am" (regardless of what is in the "From:"
> header of the email).
>
Thanks for the hint. Indeed that's what the git am docu says:
"From: " and "Subject: " lines starting the body override the
respective commit author name and title values taken from the
headers.
Patchwork doesn't seem to be that smart ..
> HTH,
> Karsten
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905)
2017-02-02 19:41 ` Heiner Kallweit
@ 2017-02-02 20:21 ` Andreas Färber
0 siblings, 0 replies; 7+ messages in thread
From: Andreas Färber @ 2017-02-02 20:21 UTC (permalink / raw)
To: u-boot
Am 02.02.2017 um 20:41 schrieb Heiner Kallweit:
> Am 02.02.2017 um 20:33 schrieb Karsten Merker:
>> On Thu, Feb 02, 2017 at 08:10:54PM +0100, Heiner Kallweit wrote:
>>> Am 31.01.2017 um 14:24 schrieb Jaehoon Chung:
>>>> On 01/28/2017 05:55 AM, Heiner Kallweit wrote:
>>>>> This driver implements MMC support on Meson GX (S905) based systems.
>>>>> It's based on Carlo Caione's work, changes:
>>>>> - BLK support added
>>>>> - general refactoring
>>>>>
>>>>> Signed-off-by: Carlo Caione <carlo@caione.org>
>>>>> Signed-off-by: Andreas F?rber <afaerber@suse.de>
>>>>> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
>>>>
>>>> Andreas's comment is what this patch's author is Carlo..Not
>>>> just add Signed-off tag for Carlo.
>>>>
>>>> When you send the email, needs to add "From: Carlo Caione
>>>> <carlo@caione.org>", not yours.
>>>>
>>> I sent a v4 series addressing the review comments.
>>> I tried sending patch 2 with Carlo as "From:", however the mail
>>> provider replaced this with my default mail address.
>>> I checked with my other mail providers, they also allow only
>>> sender addresses belonging to me.
>>
>> IIRC putting "From: Carlo Caione <carlo@caione.org>" as the
>> first line in the commit log makes git set the patch author
>> accordingly during "git am" (regardless of what is in the "From:"
>> header of the email).
>>
> Thanks for the hint. Indeed that's what the git am docu says:
> "From: " and "Subject: " lines starting the body override the
> respective commit author name and title values taken from the
> headers.
> Patchwork doesn't seem to be that smart ..
I believe I already pointed you to the --author command line option?
git commit --amend --author="Carlo ... <...>"
Regards,
Andreas
--
SUSE Linux GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Felix Imend?rffer, Jane Smithard, Graham Norton
HRB 21284 (AG N?rnberg)
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2017-02-02 20:21 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <f28d33f6-8c8a-c40e-1ae4-cc5f7e4f9511@gmail.com>
2017-01-27 20:55 ` [U-Boot] [PATCH v3 2/3] mmc: meson: add MMC driver for Meson GX (S905) Heiner Kallweit
2017-01-31 13:24 ` Jaehoon Chung
2017-02-02 19:10 ` Heiner Kallweit
[not found] ` <20170202193351.GB6393@excalibur.cnev.de>
2017-02-02 19:41 ` Heiner Kallweit
2017-02-02 20:21 ` Andreas Färber
2017-01-27 20:56 ` [U-Boot] [PATCH v3 3/3] odroid-c2: enable new Meson GX MMC driver in board defconfig Heiner Kallweit
2017-01-31 3:48 ` Jaehoon Chung
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.