* [PATCH V3 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
@ 2020-05-13 18:10 Marek Vasut
2020-05-13 18:10 ` [PATCH V3 2/4] ARM: dts: stm32: Add GPIO LEDs " Marek Vasut
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Marek Vasut @ 2020-05-13 18:10 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32
Add bindings for the four GPIO keys on DH PDK2 board. Note that TA1
key is polled because it's IRQ line conflicts with ethernet IRQ, the
rest of the GPIO keys, TA2, TA3, TA4, are interrupt-driven and wake
up sources.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
V3: No change
---
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 43 ++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
index 13b1586d4a8f..e5036c9b9e92 100644
--- a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts
@@ -4,6 +4,7 @@
*/
#include "stm32mp157c-dhcom-som.dtsi"
+#include <dt-bindings/input/input.h>
#include <dt-bindings/pwm/pwm.h>
/ {
@@ -46,6 +47,48 @@ ethernet_vio: vioregulator {
regulator-boot-on;
};
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ /*
+ * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
+ * so mark this as polled GPIO key.
+ */
+ button-0 {
+ label = "TA1-GPIO-A";
+ linux,code = <KEY_A>;
+ gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #size-cells = <0>;
+
+ button-1 {
+ label = "TA2-GPIO-B";
+ linux,code = <KEY_B>;
+ gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ button-2 {
+ label = "TA3-GPIO-C";
+ linux,code = <KEY_C>;
+ gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ button-3 {
+ label = "TA4-GPIO-D";
+ linux,code = <KEY_D>;
+ gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
panel {
compatible = "edt,etm0700g0edh6";
backlight = <&display_bl>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH V3 2/4] ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2 2020-05-13 18:10 [PATCH V3 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut @ 2020-05-13 18:10 ` Marek Vasut 2020-05-13 18:10 ` [PATCH V3 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2 Marek Vasut 2020-05-13 18:10 ` [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut 2 siblings, 0 replies; 6+ messages in thread From: Marek Vasut @ 2020-05-13 18:10 UTC (permalink / raw) To: linux-arm-kernel Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay, Maxime Coquelin, linux-stm32 Add bindings for the four GPIO LEDs on DH PDK2 board. Note that LED5 GPIO-E may conflict with touchscreen interrupt, hence LED5 must be disabled when using the DH 560-200 display unit with touchscreen. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org --- V2: No change V3: No change --- arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 28 ++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts index e5036c9b9e92..b380268750f3 100644 --- a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +++ b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts @@ -89,6 +89,34 @@ button-3 { }; }; + led { + compatible = "gpio-leds"; + + led-0 { + label = "green:led5"; + gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-1 { + label = "green:led6"; + gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "green:led7"; + gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-3 { + label = "green:led8"; + gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + panel { compatible = "edt,etm0700g0edh6"; backlight = <&display_bl>; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH V3 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2 2020-05-13 18:10 [PATCH V3 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut 2020-05-13 18:10 ` [PATCH V3 2/4] ARM: dts: stm32: Add GPIO LEDs " Marek Vasut @ 2020-05-13 18:10 ` Marek Vasut 2020-05-13 18:10 ` [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut 2 siblings, 0 replies; 6+ messages in thread From: Marek Vasut @ 2020-05-13 18:10 UTC (permalink / raw) To: linux-arm-kernel Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay, Maxime Coquelin, linux-stm32 The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx variant. Split the SoC-independent parts of the SoM and PDK2 into the stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example of adding STM32MP157C variant of the SoM into a PDK2 carrier board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org --- V2: - Drop the stm32mp157c-dhcom-som.dtsi , as it was just include statements - Add comment about what SoM+Board combination is currently supported V3: Move the comment to stm32mp157c-dhcom-pdk2.dts --- arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts | 348 +----------------- arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 337 +++++++++++++++++ ...om-som.dtsi => stm32mp15xx-dhcom-som.dtsi} | 5 +- 3 files changed, 352 insertions(+), 338 deletions(-) create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi rename arch/arm/boot/dts/{stm32mp157c-dhcom-som.dtsi => stm32mp15xx-dhcom-som.dtsi} (98%) diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts index b380268750f3..197aa98d49e2 100644 --- a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +++ b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts @@ -1,243 +1,23 @@ // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause /* - * Copyright (C) 2019 Marek Vasut <marex@denx.de> + * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de> + * + * DHCOM STM32MP1 variant: + * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2 + * DHCOR PCB number: 587-200 or newer + * PDK2 PCB number: 516-400 or newer */ +/dts-v1/; -#include "stm32mp157c-dhcom-som.dtsi" -#include <dt-bindings/input/input.h> -#include <dt-bindings/pwm/pwm.h> +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15xx-dhcom-som.dtsi" +#include "stm32mp15xx-dhcom-pdk2.dtsi" / { - model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)"; - compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157"; - - aliases { - serial0 = &uart4; - serial1 = &usart3; - serial2 = &uart8; - ethernet0 = ðernet0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - clk_ext_audio_codec: clock-codec { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <24000000>; - }; - - display_bl: display-bl { - compatible = "pwm-backlight"; - pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; - brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>; - default-brightness-level = <8>; - enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>; - status = "okay"; - }; - - ethernet_vio: vioregulator { - compatible = "regulator-fixed"; - regulator-name = "vio"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpiog 3 GPIO_ACTIVE_LOW>; - regulator-always-on; - regulator-boot-on; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #size-cells = <0>; - poll-interval = <20>; - - /* - * The EXTi IRQ line 3 is shared with touchscreen and ethernet, - * so mark this as polled GPIO key. - */ - button-0 { - label = "TA1-GPIO-A"; - linux,code = <KEY_A>; - gpios = <&gpiof 3 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - #size-cells = <0>; - - button-1 { - label = "TA2-GPIO-B"; - linux,code = <KEY_B>; - gpios = <&gpiod 6 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - - button-2 { - label = "TA3-GPIO-C"; - linux,code = <KEY_C>; - gpios = <&gpioi 11 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - - button-3 { - label = "TA4-GPIO-D"; - linux,code = <KEY_D>; - gpios = <&gpiod 12 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - }; - - led { - compatible = "gpio-leds"; - - led-0 { - label = "green:led5"; - gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led-1 { - label = "green:led6"; - gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led-2 { - label = "green:led7"; - gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led-3 { - label = "green:led8"; - gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - panel { - compatible = "edt,etm0700g0edh6"; - backlight = <&display_bl>; - - port { - lcd_panel_in: endpoint { - remote-endpoint = <&lcd_display_out>; - }; - }; - }; - - sound { - compatible = "audio-graph-card"; - routing = - "MIC_IN", "Capture", - "Capture", "Mic Bias", - "Playback", "HP_OUT"; - dais = <&sai2a_port &sai2b_port>; - status = "okay"; - }; -}; - -&cec { - pinctrl-names = "default"; - pinctrl-0 = <&cec_pins_a>; - status = "okay"; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rmii_pins_a>; - pinctrl-1 = <ðernet0_rmii_sleep_pins_a>; - pinctrl-names = "default", "sleep"; - phy-mode = "rmii"; - max-speed = <100>; - phy-handle = <&phy0>; - st,eth-ref-clk-sel; - phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - - phy0: ethernet-phy@1 { - reg = <1>; - }; - }; -}; - -&i2c2 { /* Header X22 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /* spare dmas for other usage */ - /delete-property/dmas; - /delete-property/dma-names; - status = "okay"; -}; - -&i2c5 { /* Header X21 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c5_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /* spare dmas for other usage */ - /delete-property/dmas; - /delete-property/dma-names; - - sgtl5000: codec@a { - compatible = "fsl,sgtl5000"; - reg = <0x0a>; - #sound-dai-cells = <0>; - clocks = <&clk_ext_audio_codec>; - VDDA-supply = <&v3v3>; - VDDIO-supply = <&vdd>; - - sgtl5000_port: port { - #address-cells = <1>; - #size-cells = <0>; - - sgtl5000_tx_endpoint: endpoint@0 { - reg = <0>; - remote-endpoint = <&sai2a_endpoint>; - frame-master; - bitclock-master; - }; - - sgtl5000_rx_endpoint: endpoint@1 { - reg = <1>; - remote-endpoint = <&sai2b_endpoint>; - frame-master; - bitclock-master; - }; - }; - - }; - - polytouch@38 { - compatible = "edt,edt-ft5x06"; - reg = <0x38>; - interrupt-parent = <&gpiog>; - interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */ - linux,wakeup; - }; -}; - -<dc { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <<dc_pins_b>; - pinctrl-1 = <<dc_sleep_pins_b>; - status = "okay"; - - port { - lcd_display_out: endpoint { - remote-endpoint = <&lcd_panel_in>; - }; - }; + model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)"; + compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som", + "st,stm32mp157"; }; &m_can1 { @@ -246,103 +26,3 @@ &m_can1 { pinctrl-1 = <&m_can1_sleep_pins_a>; status = "okay"; }; - -&sai2 { - clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; - clock-names = "pclk", "x8k", "x11k"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>; - pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>; - status = "okay"; - - sai2a: audio-controller@4400b004 { - #clock-cells = <0>; - dma-names = "tx"; - clocks = <&rcc SAI2_K>; - clock-names = "sai_ck"; - status = "okay"; - - sai2a_port: port { - sai2a_endpoint: endpoint { - remote-endpoint = <&sgtl5000_tx_endpoint>; - format = "i2s"; - mclk-fs = <512>; - dai-tdm-slot-num = <2>; - dai-tdm-slot-width = <16>; - }; - }; - }; - - sai2b: audio-controller@4400b024 { - dma-names = "rx"; - st,sync = <&sai2a 2>; - clocks = <&rcc SAI2_K>, <&sai2a>; - clock-names = "sai_ck", "MCLK"; - status = "okay"; - - sai2b_port: port { - sai2b_endpoint: endpoint { - remote-endpoint = <&sgtl5000_rx_endpoint>; - format = "i2s"; - mclk-fs = <512>; - dai-tdm-slot-num = <2>; - dai-tdm-slot-width = <16>; - }; - }; - }; -}; - -&timers2 { - /* spare dmas for other usage (un-delete to enable pwm capture) */ - /delete-property/dmas; - /delete-property/dma-names; - status = "okay"; - pwm2: pwm { - pinctrl-0 = <&pwm2_pins_a>; - pinctrl-names = "default"; - status = "okay"; - }; - timer@1 { - status = "okay"; - }; -}; - -&usart3 { - pinctrl-names = "default"; - pinctrl-0 = <&usart3_pins_a>; - status = "okay"; -}; - -&uart8 { - pinctrl-names = "default"; - pinctrl-0 = <&uart8_pins_a>; - status = "okay"; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - status = "okay"; -}; - -&usbotg_hs { - dr_mode = "peripheral"; - phys = <&usbphyc_port1 0>; - phy-names = "usb2-phy"; - status = "okay"; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; - -&usbphyc_port1 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi new file mode 100644 index 000000000000..7c4bd615b311 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi @@ -0,0 +1,337 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de> + */ + +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + serial0 = &uart4; + serial1 = &usart3; + serial2 = &uart8; + ethernet0 = ðernet0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clk_ext_audio_codec: clock-codec { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; + + display_bl: display-bl { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>; + default-brightness-level = <8>; + enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + ethernet_vio: vioregulator { + compatible = "regulator-fixed"; + regulator-name = "vio"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpiog 3 GPIO_ACTIVE_LOW>; + regulator-always-on; + regulator-boot-on; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #size-cells = <0>; + poll-interval = <20>; + + /* + * The EXTi IRQ line 3 is shared with touchscreen and ethernet, + * so mark this as polled GPIO key. + */ + button-0 { + label = "TA1-GPIO-A"; + linux,code = <KEY_A>; + gpios = <&gpiof 3 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #size-cells = <0>; + + button-1 { + label = "TA2-GPIO-B"; + linux,code = <KEY_B>; + gpios = <&gpiod 6 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + + button-2 { + label = "TA3-GPIO-C"; + linux,code = <KEY_C>; + gpios = <&gpioi 11 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + + button-3 { + label = "TA4-GPIO-D"; + linux,code = <KEY_D>; + gpios = <&gpiod 12 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + }; + + led { + compatible = "gpio-leds"; + + led-0 { + label = "green:led5"; + gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-1 { + label = "green:led6"; + gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "green:led7"; + gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-3 { + label = "green:led8"; + gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + panel { + compatible = "edt,etm0700g0edh6"; + backlight = <&display_bl>; + + port { + lcd_panel_in: endpoint { + remote-endpoint = <&lcd_display_out>; + }; + }; + }; + + sound { + compatible = "audio-graph-card"; + routing = + "MIC_IN", "Capture", + "Capture", "Mic Bias", + "Playback", "HP_OUT"; + dais = <&sai2a_port &sai2b_port>; + status = "okay"; + }; +}; + +&cec { + pinctrl-names = "default"; + pinctrl-0 = <&cec_pins_a>; + status = "okay"; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rmii_pins_a>; + pinctrl-1 = <ðernet0_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + max-speed = <100>; + phy-handle = <&phy0>; + st,eth-ref-clk-sel; + phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@1 { + reg = <1>; + }; + }; +}; + +&i2c2 { /* Header X22 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; +}; + +&i2c5 { /* Header X21 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + + sgtl5000: codec@a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + #sound-dai-cells = <0>; + clocks = <&clk_ext_audio_codec>; + VDDA-supply = <&v3v3>; + VDDIO-supply = <&vdd>; + + sgtl5000_port: port { + #address-cells = <1>; + #size-cells = <0>; + + sgtl5000_tx_endpoint: endpoint@0 { + reg = <0>; + remote-endpoint = <&sai2a_endpoint>; + frame-master; + bitclock-master; + }; + + sgtl5000_rx_endpoint: endpoint@1 { + reg = <1>; + remote-endpoint = <&sai2b_endpoint>; + frame-master; + bitclock-master; + }; + }; + + }; + + polytouch@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpiog>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */ + linux,wakeup; + }; +}; + +<dc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <<dc_pins_b>; + pinctrl-1 = <<dc_sleep_pins_b>; + status = "okay"; + + port { + lcd_display_out: endpoint { + remote-endpoint = <&lcd_panel_in>; + }; + }; +}; + +&sai2 { + clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + clock-names = "pclk", "x8k", "x11k"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>; + pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>; + status = "okay"; + + sai2a: audio-controller@4400b004 { + #clock-cells = <0>; + dma-names = "tx"; + clocks = <&rcc SAI2_K>; + clock-names = "sai_ck"; + status = "okay"; + + sai2a_port: port { + sai2a_endpoint: endpoint { + remote-endpoint = <&sgtl5000_tx_endpoint>; + format = "i2s"; + mclk-fs = <512>; + dai-tdm-slot-num = <2>; + dai-tdm-slot-width = <16>; + }; + }; + }; + + sai2b: audio-controller@4400b024 { + dma-names = "rx"; + st,sync = <&sai2a 2>; + clocks = <&rcc SAI2_K>, <&sai2a>; + clock-names = "sai_ck", "MCLK"; + status = "okay"; + + sai2b_port: port { + sai2b_endpoint: endpoint { + remote-endpoint = <&sgtl5000_rx_endpoint>; + format = "i2s"; + mclk-fs = <512>; + dai-tdm-slot-num = <2>; + dai-tdm-slot-width = <16>; + }; + }; + }; +}; + +&timers2 { + /* spare dmas for other usage (un-delete to enable pwm capture) */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + pwm2: pwm { + pinctrl-0 = <&pwm2_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@1 { + status = "okay"; + }; +}; + +&usart3 { + pinctrl-names = "default"; + pinctrl-0 = <&usart3_pins_a>; + status = "okay"; +}; + +&uart8 { + pinctrl-names = "default"; + pinctrl-0 = <&uart8_pins_a>; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "peripheral"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi similarity index 98% rename from arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi rename to arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi index f97e0d2ecf17..ba905196fb54 100644 --- a/arch/arm/boot/dts/stm32mp157c-dhcom-som.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi @@ -1,11 +1,8 @@ // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) /* - * Copyright (C) 2019 Marek Vasut <marex@denx.de> + * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de> */ -/dts-v1/; -#include "stm32mp157.dtsi" -#include "stm32mp15xc.dtsi" #include "stm32mp15-pinctrl.dtsi" #include "stm32mp15xxaa-pinctrl.dtsi" #include <dt-bindings/gpio/gpio.h> -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board 2020-05-13 18:10 [PATCH V3 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut 2020-05-13 18:10 ` [PATCH V3 2/4] ARM: dts: stm32: Add GPIO LEDs " Marek Vasut 2020-05-13 18:10 ` [PATCH V3 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2 Marek Vasut @ 2020-05-13 18:10 ` Marek Vasut 2020-05-14 5:18 ` Manivannan Sadhasivam 2020-05-14 14:27 ` Alexandre Torgue 2 siblings, 2 replies; 6+ messages in thread From: Marek Vasut @ 2020-05-13 18:10 UTC (permalink / raw) To: linux-arm-kernel Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay, Maxime Coquelin, Manivannan Sadhasivam, linux-stm32 The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top of an Avenger96 reference board. The DHCOR SoM can be populated with any STM32MP15xx. Split the DTs to reflect this such that the common SoM and Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example implementation of STM32MP157A SoM and Avenger96 board is separated into stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for the sake of backward naming compatibility. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org --- V2: - Drop the stm32mp157a-dhcor-som.dtsi , as it was just include statements - Add comment about what SoM+Board combination is currently supported V3: No change --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +----------------- .../boot/dts/stm32mp157a-dhcor-avenger96.dts | 38 ++ .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++ .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 + arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++ 6 files changed, 675 insertions(+), 615 deletions(-) create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f43467b02bcd..d0f6c5838568 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1029,6 +1029,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32h743i-eval.dtb \ stm32h743i-disco.dtb \ stm32mp157a-avenger96.dtb \ + stm32mp157a-dhcor-avenger96.dtb \ stm32mp157a-dk1.dtb \ stm32mp157c-dhcom-pdk2.dtb \ stm32mp157c-dk2.dtb \ diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts index a9f3ba9da170..8a6eaca994d1 100644 --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts @@ -2,622 +2,10 @@ /* * Copyright (C) Linaro Ltd 2019 - All Rights Reserved * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + * Copyright (C) 2020 Marek Vasut <marex@denx.de> */ /dts-v1/; -#include "stm32mp157.dtsi" -#include "stm32mp15-pinctrl.dtsi" -#include "stm32mp15xxac-pinctrl.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/mfd/st,stpmic1.h> - -/ { - model = "Arrow Electronics STM32MP157A Avenger96 board"; - compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; - - aliases { - ethernet0 = ðernet0; - mmc0 = &sdmmc1; - serial0 = &uart4; - serial1 = &uart7; - serial2 = &usart2; - spi0 = &qspi; - }; - - /* XTal Q1 */ - cec_clock: clk-cec-fixed { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <24000000>; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - hdmi-out { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con: endpoint { - remote-endpoint = <&adv7513_out>; - }; - }; - }; - - memory@c0000000 { - device_type = "memory"; - reg = <0xc0000000 0x40000000>; - }; - - led { - compatible = "gpio-leds"; - led1 { - label = "green:user0"; - gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - led2 { - label = "green:user1"; - gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - led3 { - label = "green:user2"; - gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - led4 { - label = "green:user3"; - gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - panic-indicator; - }; - }; - - sd_switch: regulator-sd_switch { - compatible = "regulator-gpio"; - regulator-name = "sd_switch"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-type = "voltage"; - regulator-always-on; - - gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - states = <1800000 0x1>, - <2900000 0x0>; - }; - - sound { - compatible = "audio-graph-card"; - label = "STM32MP1-AV96-HDMI"; - dais = <&sai2a_port>; - status = "okay"; - }; - - /* Enpirion EP3A8LQI U2 on the DHCOR */ - vdd_io: regulator-buck-io { - compatible = "regulator-fixed"; - regulator-name = "buck-io"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <&vdd>; - }; - - wlan_pwr: regulator-wlan { - compatible = "regulator-fixed"; - - regulator-name = "wl-reg"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&adc { - pinctrl-names = "default"; - pinctrl-0 = <&adc12_ain_pins_b>; - vdd-supply = <&vdd>; - vdda-supply = <&vdda>; - vref-supply = <&vdda>; - status = "okay"; - - adc1: adc@0 { - st,adc-channels = <0 1 6>; - st,min-sample-time-nsecs = <5000>; - status = "okay"; - }; - - adc2: adc@100 { - st,adc-channels = <0 1 2>; - st,min-sample-time-nsecs = <5000>; - status = "okay"; - }; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_c>; - pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; - pinctrl-names = "default", "sleep"; - phy-mode = "rgmii"; - max-speed = <1000>; - phy-handle = <&phy0>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; - reset-delay-us = <1000>; - - phy0: ethernet-phy@7 { - reg = <7>; - - rxc-skew-ps = <1500>; - rxdv-skew-ps = <540>; - rxd0-skew-ps = <420>; - rxd1-skew-ps = <420>; - rxd2-skew-ps = <420>; - rxd3-skew-ps = <420>; - - txc-skew-ps = <1440>; - txen-skew-ps = <540>; - txd0-skew-ps = <420>; - txd1-skew-ps = <420>; - txd2-skew-ps = <420>; - txd3-skew-ps = <420>; - }; - }; -}; - -&i2c1 { /* X6 I2C1 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_b>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c2 { /* X6 I2C2 */ - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_c>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&i2c4 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - /delete-property/dmas; - /delete-property/dma-names; - - pmic: stpmic@33 { - compatible = "st,stpmic1"; - reg = <0x33>; - interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; - interrupt-controller; - #interrupt-cells = <2>; - status = "okay"; - - regulators { - compatible = "st,stpmic1-regulators"; - - ldo1-supply = <&v3v3>; - ldo2-supply = <&v3v3>; - ldo3-supply = <&vdd_ddr>; - ldo5-supply = <&v3v3>; - ldo6-supply = <&v3v3>; - pwr_sw1-supply = <&bst_out>; - pwr_sw2-supply = <&bst_out>; - - vddcore: buck1 { - regulator-name = "vddcore"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd_ddr: buck2 { - regulator-name = "vdd_ddr"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd: buck3 { - regulator-name = "vdd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - v3v3: buck4 { - regulator-name = "v3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-over-current-protection; - regulator-initial-mode = <0>; - }; - - vdda: ldo1 { - regulator-name = "vdda"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = <IT_CURLIM_LDO1 0>; - }; - - v2v8: ldo2 { - regulator-name = "v2v8"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - interrupts = <IT_CURLIM_LDO2 0>; - }; - - vtt_ddr: ldo3 { - regulator-name = "vtt_ddr"; - regulator-min-microvolt = <500000>; - regulator-max-microvolt = <750000>; - regulator-always-on; - regulator-over-current-protection; - }; - - vdd_usb: ldo4 { - regulator-name = "vdd_usb"; - interrupts = <IT_CURLIM_LDO4 0>; - }; - - vdd_sd: ldo5 { - regulator-name = "vdd_sd"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - interrupts = <IT_CURLIM_LDO5 0>; - regulator-boot-on; - }; - - v1v8: ldo6 { - regulator-name = "v1v8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = <IT_CURLIM_LDO6 0>; - regulator-enable-ramp-delay = <300000>; - }; - - vref_ddr: vref_ddr { - regulator-name = "vref_ddr"; - regulator-always-on; - }; - - bst_out: boost { - regulator-name = "bst_out"; - interrupts = <IT_OCP_BOOST 0>; - }; - - vbus_otg: pwr_sw1 { - regulator-name = "vbus_otg"; - interrupts = <IT_OCP_OTG 0>; - regulator-active-discharge = <1>; - }; - - vbus_sw: pwr_sw2 { - regulator-name = "vbus_sw"; - interrupts = <IT_OCP_SWOUT 0>; - regulator-active-discharge = <1>; - }; - }; - - onkey { - compatible = "st,stpmic1-onkey"; - interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; - interrupt-names = "onkey-falling", "onkey-rising"; - status = "okay"; - }; - - watchdog { - compatible = "st,stpmic1-wdt"; - status = "disabled"; - }; - }; - - hdmi-transmitter@3d { - compatible = "adi,adv7513"; - reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; - reg-names = "main", "cec", "edid", "packet"; - clocks = <&cec_clock>; - clock-names = "cec"; - - avdd-supply = <&v3v3>; - dvdd-supply = <&v3v3>; - pvdd-supply = <&v3v3>; - dvdd-3v-supply = <&v3v3>; - bgvdd-supply = <&v3v3>; - - interrupts = <9 IRQ_TYPE_EDGE_FALLING>; - interrupt-parent = <&gpiog>; - - status = "okay"; - - adi,input-depth = <8>; - adi,input-colorspace = "rgb"; - adi,input-clock = "1x"; - adi,input-style = <1>; - adi,input-justification = "evenly"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - adv7513_in: endpoint { - remote-endpoint = <<dc_ep0_out>; - }; - }; - - port@1 { - reg = <1>; - adv7513_out: endpoint { - remote-endpoint = <&hdmi_con>; - }; - }; - - port@2 { - reg = <2>; - adv7513_i2s0: endpoint { - remote-endpoint = <&sai2a_endpoint>; - }; - }; - }; - }; - - eeprom@53 { - compatible = "atmel,24c02"; - reg = <0x53>; - pagesize = <16>; - }; -}; - -&iwdg2 { - timeout-sec = <32>; - status = "okay"; -}; - -<dc { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <<dc_pins_d>; - pinctrl-1 = <<dc_sleep_pins_d>; - status = "okay"; - - port { - #address-cells = <1>; - #size-cells = <0>; - - ltdc_ep0_out: endpoint@0 { - reg = <0>; - remote-endpoint = <&adv7513_in>; - }; - }; -}; - -&m_can1 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can1_pins_b>; - pinctrl-1 = <&m_can1_sleep_pins_b>; - status = "disabled"; -}; - -&m_can2 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can2_pins_a>; - pinctrl-1 = <&m_can2_sleep_pins_a>; - status = "disabled"; -}; - -&pwr_regulators { - vdd-supply = <&vdd_io>; - vdd_3v3_usbfs-supply = <&vdd_usb>; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; - reg = <0x58003000 0x1000>, <0x70000000 0x200000>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - flash0: spi-flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -&rng1 { - status = "okay"; -}; - -&rtc { - status = "okay"; -}; - -&sai2 { - clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sai2a_pins_c>; - pinctrl-1 = <&sai2a_sleep_pins_c>; - clock-names = "pclk", "x8k", "x11k"; - status = "okay"; - - sai2a: audio-controller@4400b004 { - #clock-cells = <0>; - dma-names = "tx"; - clocks = <&rcc SAI2_K>; - clock-names = "sai_ck"; - status = "okay"; - - sai2a_port: port { - sai2a_endpoint: endpoint { - remote-endpoint = <&adv7513_i2s0>; - format = "i2s"; - mclk-fs = <256>; - }; - }; - }; -}; - -&sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; - cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; - disable-wp; - st,sig-dir; - st,neg-edge; - st,use-ckin; - bus-width = <4>; - vmmc-supply = <&vdd_sd>; - vqmmc-supply = <&sd_switch>; - status = "okay"; -}; - -&sdmmc2 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; - pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; - pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; - bus-width = <8>; - mmc-ddr-1_8v; - no-sd; - no-sdio; - non-removable; - st,neg-edge; - vmmc-supply = <&v3v3>; - vqmmc-supply = <&vdd_io>; - status = "okay"; -}; - -&sdmmc3 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc3_b4_pins_b>; - pinctrl-1 = <&sdmmc3_b4_od_pins_b>; - pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; - broken-cd; - non-removable; - st,neg-edge; - bus-width = <4>; - vmmc-supply = <&wlan_pwr>; - status = "okay"; - - #address-cells = <1>; - #size-cells = <0>; - brcmf: bcrmf@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -&spi2 { - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_a>; - cs-gpios = <&gpioi 0 0>; - status = "disabled"; - /delete-property/dmas; - /delete-property/dma-names; -}; - -&uart4 { - /* On Low speed expansion header */ - label = "LS-UART1"; - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins_b>; - status = "okay"; -}; - -&uart7 { - /* On Low speed expansion header */ - label = "LS-UART0"; - pinctrl-names = "default"; - pinctrl-0 = <&uart7_pins_a>; - status = "okay"; -}; - -/* Bluetooth */ -&usart2 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&usart2_pins_a>; - pinctrl-1 = <&usart2_sleep_pins_a>; - st,hw-flow-ctrl; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <3000000>; - shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; - }; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - phy-names = "usb"; - status = "okay"; -}; - -&usbotg_hs { - pinctrl-0 = <&usbotg_hs_pins_a>; - pinctrl-names = "default"; - phy-names = "usb2-phy"; - phys = <&usbphyc_port1 0>; - status = "okay"; - vbus-supply = <&vbus_otg>; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; - -&usbphyc_port1 { - phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; -}; +/* This DT is here only for backward compatibility */ +#include "stm32mp157a-dhcor-avenger96.dts" diff --git a/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts new file mode 100644 index 000000000000..2e3c9fbb4eb3 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts @@ -0,0 +1,38 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + * Copyright (C) 2020 Marek Vasut <marex@denx.de> + * + * DHCOR STM32MP1 variant: + * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG + * DHCOR PCB number: 586-100 or newer + * Avenger96 PCB number: 588-200 or newer + */ + +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15xx-dhcor-som.dtsi" +#include "stm32mp15xx-dhcor-avenger96.dtsi" + +/ { + model = "Arrow Electronics STM32MP157A Avenger96 board"; + compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som", + "st,stm32mp157"; +}; + +&m_can1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can1_pins_b>; + pinctrl-1 = <&m_can1_sleep_pins_b>; + status = "disabled"; +}; + +&m_can2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can2_pins_a>; + pinctrl-1 = <&m_can2_sleep_pins_a>; + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi new file mode 100644 index 000000000000..930202742a3f --- /dev/null +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi @@ -0,0 +1,401 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + * Copyright (C) 2020 Marek Vasut <marex@denx.de> + */ + +/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */ +#include "stm32mp15xx-dhcor-io1v8.dtsi" + +/ { + aliases { + ethernet0 = ðernet0; + mmc0 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + serial2 = &usart2; + spi0 = &qspi; + }; + + /* XTal Q1 */ + cec_clock: clk-cec-fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7513_out>; + }; + }; + }; + + led { + compatible = "gpio-leds"; + led1 { + label = "green:user0"; + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led2 { + label = "green:user1"; + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led3 { + label = "green:user2"; + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "green:user3"; + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + panic-indicator; + }; + }; + + sd_switch: regulator-sd_switch { + compatible = "regulator-gpio"; + regulator-name = "sd_switch"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-type = "voltage"; + regulator-always-on; + + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1>, + <2900000 0x0>; + }; + + sound { + compatible = "audio-graph-card"; + label = "STM32MP1-AV96-HDMI"; + dais = <&sai2a_port>; + status = "okay"; + }; + + wlan_pwr: regulator-wlan { + compatible = "regulator-fixed"; + + regulator-name = "wl-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&adc { + pinctrl-names = "default"; + pinctrl-0 = <&adc12_ain_pins_b>; + vdd-supply = <&vdd>; + vdda-supply = <&vdda>; + vref-supply = <&vdda>; + status = "okay"; + + adc1: adc@0 { + st,adc-channels = <0 1 6>; + st,min-sample-time-nsecs = <5000>; + status = "okay"; + }; + + adc2: adc@100 { + st,adc-channels = <0 1 2>; + st,min-sample-time-nsecs = <5000>; + status = "okay"; + }; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rgmii_pins_c>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii"; + max-speed = <1000>; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; + reset-delay-us = <1000>; + + phy0: ethernet-phy@7 { + reg = <7>; + + rxc-skew-ps = <1500>; + rxdv-skew-ps = <540>; + rxd0-skew-ps = <420>; + rxd1-skew-ps = <420>; + rxd2-skew-ps = <420>; + rxd3-skew-ps = <420>; + + txc-skew-ps = <1440>; + txen-skew-ps = <540>; + txd0-skew-ps = <420>; + txd1-skew-ps = <420>; + txd2-skew-ps = <420>; + txd3-skew-ps = <420>; + }; + }; +}; + +&i2c1 { /* X6 I2C1 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_b>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c2 { /* X6 I2C2 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_c>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c4 { + hdmi-transmitter@3d { + compatible = "adi,adv7513"; + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; + reg-names = "main", "cec", "edid", "packet"; + clocks = <&cec_clock>; + clock-names = "cec"; + + avdd-supply = <&v3v3>; + dvdd-supply = <&v3v3>; + pvdd-supply = <&v3v3>; + dvdd-3v-supply = <&v3v3>; + bgvdd-supply = <&v3v3>; + + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpiog>; + + status = "okay"; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7513_in: endpoint { + remote-endpoint = <<dc_ep0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7513_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + + port@2 { + reg = <2>; + adv7513_i2s0: endpoint { + remote-endpoint = <&sai2a_endpoint>; + }; + }; + }; + }; +}; + +<dc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <<dc_pins_d>; + pinctrl-1 = <<dc_sleep_pins_d>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ltdc_ep0_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&adv7513_in>; + }; + }; +}; + +&sai2 { + clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai2a_pins_c>; + pinctrl-1 = <&sai2a_sleep_pins_c>; + clock-names = "pclk", "x8k", "x11k"; + status = "okay"; + + sai2a: audio-controller@4400b004 { + #clock-cells = <0>; + dma-names = "tx"; + clocks = <&rcc SAI2_K>; + clock-names = "sai_ck"; + status = "okay"; + + sai2a_port: port { + sai2a_endpoint: endpoint { + remote-endpoint = <&adv7513_i2s0>; + format = "i2s"; + mclk-fs = <256>; + }; + }; + }; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; + cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,sig-dir; + st,neg-edge; + st,use-ckin; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + vqmmc-supply = <&sd_switch>; + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; + bus-width = <8>; + mmc-ddr-1_8v; + no-sd; + no-sdio; + non-removable; + st,neg-edge; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&vdd_io>; + status = "okay"; +}; + +&sdmmc3 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc3_b4_pins_b>; + pinctrl-1 = <&sdmmc3_b4_od_pins_b>; + pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; + broken-cd; + non-removable; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&wlan_pwr>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + cs-gpios = <&gpioi 0 0>; + status = "disabled"; + /delete-property/dmas; + /delete-property/dma-names; +}; + +&uart4 { + /* On Low speed expansion header */ + label = "LS-UART1"; + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_b>; + status = "okay"; +}; + +&uart7 { + /* On Low speed expansion header */ + label = "LS-UART0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; +}; + +/* Bluetooth */ +&usart2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&usart2_pins_a>; + pinctrl-1 = <&usart2_sleep_pins_a>; + st,hw-flow-ctrl; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <3000000>; + shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + pinctrl-0 = <&usbotg_hs_pins_a>; + pinctrl-names = "default"; + phy-names = "usb2-phy"; + phys = <&usbphyc_port1 0>; + status = "okay"; + vbus-supply = <&vbus_otg>; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi new file mode 100644 index 000000000000..75172314d7af --- /dev/null +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + * Copyright (C) 2020 Marek Vasut <marex@denx.de> + */ + +/ { + /* Enpirion EP3A8LQI U2 on the DHCOR */ + vdd_io: regulator-buck-io { + compatible = "regulator-fixed"; + regulator-name = "buck-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd>; + }; +}; + +&pwr_regulators { + vdd-supply = <&vdd_io>; +}; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi new file mode 100644 index 000000000000..04fbb324a541 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi @@ -0,0 +1,209 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +/* + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + * Copyright (C) 2020 Marek Vasut <marex@denx.de> + */ + +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxac-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + aliases { + spi0 = &qspi; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x40000000>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO6 0>; + regulator-enable-ramp-delay = <300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + regulator-active-discharge = <1>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + regulator-active-discharge = <1>; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; + + eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x200000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: spi-flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board 2020-05-13 18:10 ` [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut @ 2020-05-14 5:18 ` Manivannan Sadhasivam 2020-05-14 14:27 ` Alexandre Torgue 1 sibling, 0 replies; 6+ messages in thread From: Manivannan Sadhasivam @ 2020-05-14 5:18 UTC (permalink / raw) To: Marek Vasut Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay, Maxime Coquelin, linux-stm32, linux-arm-kernel On Wed, May 13, 2020 at 08:10:20PM +0200, Marek Vasut wrote: > The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top > of an Avenger96 reference board. The DHCOR SoM can be populated with any > STM32MP15xx. Split the DTs to reflect this such that the common SoM and > Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example > implementation of STM32MP157A SoM and Avenger96 board is separated into > stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for > the sake of backward naming compatibility. > > Signed-off-by: Marek Vasut <marex@denx.de> LGTM. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Thanks, Mani > Cc: Alexandre Torgue <alexandre.torgue@st.com> > Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> > Cc: Patrice Chotard <patrice.chotard@st.com> > Cc: Patrick Delaunay <patrick.delaunay@st.com> > Cc: linux-stm32@st-md-mailman.stormreply.com > To: linux-arm-kernel@lists.infradead.org > --- > V2: - Drop the stm32mp157a-dhcor-som.dtsi , as it was just include statements > - Add comment about what SoM+Board combination is currently supported > V3: No change > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +----------------- > .../boot/dts/stm32mp157a-dhcor-avenger96.dts | 38 ++ > .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++ > .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 + > arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++ > 6 files changed, 675 insertions(+), 615 deletions(-) > create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts > create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi > create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi > create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index f43467b02bcd..d0f6c5838568 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -1029,6 +1029,7 @@ dtb-$(CONFIG_ARCH_STM32) += \ > stm32h743i-eval.dtb \ > stm32h743i-disco.dtb \ > stm32mp157a-avenger96.dtb \ > + stm32mp157a-dhcor-avenger96.dtb \ > stm32mp157a-dk1.dtb \ > stm32mp157c-dhcom-pdk2.dtb \ > stm32mp157c-dk2.dtb \ > diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > index a9f3ba9da170..8a6eaca994d1 100644 > --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts > +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts > @@ -2,622 +2,10 @@ > /* > * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + * Copyright (C) 2020 Marek Vasut <marex@denx.de> > */ > > /dts-v1/; > > -#include "stm32mp157.dtsi" > -#include "stm32mp15-pinctrl.dtsi" > -#include "stm32mp15xxac-pinctrl.dtsi" > -#include <dt-bindings/gpio/gpio.h> > -#include <dt-bindings/mfd/st,stpmic1.h> > - > -/ { > - model = "Arrow Electronics STM32MP157A Avenger96 board"; > - compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157"; > - > - aliases { > - ethernet0 = ðernet0; > - mmc0 = &sdmmc1; > - serial0 = &uart4; > - serial1 = &uart7; > - serial2 = &usart2; > - spi0 = &qspi; > - }; > - > - /* XTal Q1 */ > - cec_clock: clk-cec-fixed { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <24000000>; > - }; > - > - chosen { > - stdout-path = "serial0:115200n8"; > - }; > - > - hdmi-out { > - compatible = "hdmi-connector"; > - type = "a"; > - > - port { > - hdmi_con: endpoint { > - remote-endpoint = <&adv7513_out>; > - }; > - }; > - }; > - > - memory@c0000000 { > - device_type = "memory"; > - reg = <0xc0000000 0x40000000>; > - }; > - > - led { > - compatible = "gpio-leds"; > - led1 { > - label = "green:user0"; > - gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > - linux,default-trigger = "heartbeat"; > - default-state = "off"; > - }; > - > - led2 { > - label = "green:user1"; > - gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > - linux,default-trigger = "mmc0"; > - default-state = "off"; > - }; > - > - led3 { > - label = "green:user2"; > - gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > - linux,default-trigger = "mmc1"; > - default-state = "off"; > - }; > - > - led4 { > - label = "green:user3"; > - gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > - linux,default-trigger = "none"; > - default-state = "off"; > - panic-indicator; > - }; > - }; > - > - sd_switch: regulator-sd_switch { > - compatible = "regulator-gpio"; > - regulator-name = "sd_switch"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <2900000>; > - regulator-type = "voltage"; > - regulator-always-on; > - > - gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; > - gpios-states = <0>; > - states = <1800000 0x1>, > - <2900000 0x0>; > - }; > - > - sound { > - compatible = "audio-graph-card"; > - label = "STM32MP1-AV96-HDMI"; > - dais = <&sai2a_port>; > - status = "okay"; > - }; > - > - /* Enpirion EP3A8LQI U2 on the DHCOR */ > - vdd_io: regulator-buck-io { > - compatible = "regulator-fixed"; > - regulator-name = "buck-io"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <1800000>; > - regulator-always-on; > - regulator-boot-on; > - vin-supply = <&vdd>; > - }; > - > - wlan_pwr: regulator-wlan { > - compatible = "regulator-fixed"; > - > - regulator-name = "wl-reg"; > - regulator-min-microvolt = <3300000>; > - regulator-max-microvolt = <3300000>; > - > - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > - enable-active-high; > - }; > -}; > - > -&adc { > - pinctrl-names = "default"; > - pinctrl-0 = <&adc12_ain_pins_b>; > - vdd-supply = <&vdd>; > - vdda-supply = <&vdda>; > - vref-supply = <&vdda>; > - status = "okay"; > - > - adc1: adc@0 { > - st,adc-channels = <0 1 6>; > - st,min-sample-time-nsecs = <5000>; > - status = "okay"; > - }; > - > - adc2: adc@100 { > - st,adc-channels = <0 1 2>; > - st,min-sample-time-nsecs = <5000>; > - status = "okay"; > - }; > -}; > - > -ðernet0 { > - status = "okay"; > - pinctrl-0 = <ðernet0_rgmii_pins_c>; > - pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; > - pinctrl-names = "default", "sleep"; > - phy-mode = "rgmii"; > - max-speed = <1000>; > - phy-handle = <&phy0>; > - > - mdio0 { > - #address-cells = <1>; > - #size-cells = <0>; > - compatible = "snps,dwmac-mdio"; > - reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; > - reset-delay-us = <1000>; > - > - phy0: ethernet-phy@7 { > - reg = <7>; > - > - rxc-skew-ps = <1500>; > - rxdv-skew-ps = <540>; > - rxd0-skew-ps = <420>; > - rxd1-skew-ps = <420>; > - rxd2-skew-ps = <420>; > - rxd3-skew-ps = <420>; > - > - txc-skew-ps = <1440>; > - txen-skew-ps = <540>; > - txd0-skew-ps = <420>; > - txd1-skew-ps = <420>; > - txd2-skew-ps = <420>; > - txd3-skew-ps = <420>; > - }; > - }; > -}; > - > -&i2c1 { /* X6 I2C1 */ > - pinctrl-names = "default"; > - pinctrl-0 = <&i2c1_pins_b>; > - i2c-scl-rising-time-ns = <185>; > - i2c-scl-falling-time-ns = <20>; > - status = "okay"; > - /delete-property/dmas; > - /delete-property/dma-names; > -}; > - > -&i2c2 { /* X6 I2C2 */ > - pinctrl-names = "default"; > - pinctrl-0 = <&i2c2_pins_c>; > - i2c-scl-rising-time-ns = <185>; > - i2c-scl-falling-time-ns = <20>; > - status = "okay"; > - /delete-property/dmas; > - /delete-property/dma-names; > -}; > - > -&i2c4 { > - pinctrl-names = "default"; > - pinctrl-0 = <&i2c4_pins_a>; > - i2c-scl-rising-time-ns = <185>; > - i2c-scl-falling-time-ns = <20>; > - status = "okay"; > - /delete-property/dmas; > - /delete-property/dma-names; > - > - pmic: stpmic@33 { > - compatible = "st,stpmic1"; > - reg = <0x33>; > - interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; > - interrupt-controller; > - #interrupt-cells = <2>; > - status = "okay"; > - > - regulators { > - compatible = "st,stpmic1-regulators"; > - > - ldo1-supply = <&v3v3>; > - ldo2-supply = <&v3v3>; > - ldo3-supply = <&vdd_ddr>; > - ldo5-supply = <&v3v3>; > - ldo6-supply = <&v3v3>; > - pwr_sw1-supply = <&bst_out>; > - pwr_sw2-supply = <&bst_out>; > - > - vddcore: buck1 { > - regulator-name = "vddcore"; > - regulator-min-microvolt = <1200000>; > - regulator-max-microvolt = <1350000>; > - regulator-always-on; > - regulator-initial-mode = <0>; > - regulator-over-current-protection; > - }; > - > - vdd_ddr: buck2 { > - regulator-name = "vdd_ddr"; > - regulator-min-microvolt = <1350000>; > - regulator-max-microvolt = <1350000>; > - regulator-always-on; > - regulator-initial-mode = <0>; > - regulator-over-current-protection; > - }; > - > - vdd: buck3 { > - regulator-name = "vdd"; > - regulator-min-microvolt = <2900000>; > - regulator-max-microvolt = <2900000>; > - regulator-always-on; > - regulator-initial-mode = <0>; > - regulator-over-current-protection; > - }; > - > - v3v3: buck4 { > - regulator-name = "v3v3"; > - regulator-min-microvolt = <3300000>; > - regulator-max-microvolt = <3300000>; > - regulator-always-on; > - regulator-over-current-protection; > - regulator-initial-mode = <0>; > - }; > - > - vdda: ldo1 { > - regulator-name = "vdda"; > - regulator-min-microvolt = <2900000>; > - regulator-max-microvolt = <2900000>; > - interrupts = <IT_CURLIM_LDO1 0>; > - }; > - > - v2v8: ldo2 { > - regulator-name = "v2v8"; > - regulator-min-microvolt = <2800000>; > - regulator-max-microvolt = <2800000>; > - interrupts = <IT_CURLIM_LDO2 0>; > - }; > - > - vtt_ddr: ldo3 { > - regulator-name = "vtt_ddr"; > - regulator-min-microvolt = <500000>; > - regulator-max-microvolt = <750000>; > - regulator-always-on; > - regulator-over-current-protection; > - }; > - > - vdd_usb: ldo4 { > - regulator-name = "vdd_usb"; > - interrupts = <IT_CURLIM_LDO4 0>; > - }; > - > - vdd_sd: ldo5 { > - regulator-name = "vdd_sd"; > - regulator-min-microvolt = <2900000>; > - regulator-max-microvolt = <2900000>; > - interrupts = <IT_CURLIM_LDO5 0>; > - regulator-boot-on; > - }; > - > - v1v8: ldo6 { > - regulator-name = "v1v8"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <1800000>; > - interrupts = <IT_CURLIM_LDO6 0>; > - regulator-enable-ramp-delay = <300000>; > - }; > - > - vref_ddr: vref_ddr { > - regulator-name = "vref_ddr"; > - regulator-always-on; > - }; > - > - bst_out: boost { > - regulator-name = "bst_out"; > - interrupts = <IT_OCP_BOOST 0>; > - }; > - > - vbus_otg: pwr_sw1 { > - regulator-name = "vbus_otg"; > - interrupts = <IT_OCP_OTG 0>; > - regulator-active-discharge = <1>; > - }; > - > - vbus_sw: pwr_sw2 { > - regulator-name = "vbus_sw"; > - interrupts = <IT_OCP_SWOUT 0>; > - regulator-active-discharge = <1>; > - }; > - }; > - > - onkey { > - compatible = "st,stpmic1-onkey"; > - interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > - interrupt-names = "onkey-falling", "onkey-rising"; > - status = "okay"; > - }; > - > - watchdog { > - compatible = "st,stpmic1-wdt"; > - status = "disabled"; > - }; > - }; > - > - hdmi-transmitter@3d { > - compatible = "adi,adv7513"; > - reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; > - reg-names = "main", "cec", "edid", "packet"; > - clocks = <&cec_clock>; > - clock-names = "cec"; > - > - avdd-supply = <&v3v3>; > - dvdd-supply = <&v3v3>; > - pvdd-supply = <&v3v3>; > - dvdd-3v-supply = <&v3v3>; > - bgvdd-supply = <&v3v3>; > - > - interrupts = <9 IRQ_TYPE_EDGE_FALLING>; > - interrupt-parent = <&gpiog>; > - > - status = "okay"; > - > - adi,input-depth = <8>; > - adi,input-colorspace = "rgb"; > - adi,input-clock = "1x"; > - adi,input-style = <1>; > - adi,input-justification = "evenly"; > - > - ports { > - #address-cells = <1>; > - #size-cells = <0>; > - > - port@0 { > - reg = <0>; > - adv7513_in: endpoint { > - remote-endpoint = <<dc_ep0_out>; > - }; > - }; > - > - port@1 { > - reg = <1>; > - adv7513_out: endpoint { > - remote-endpoint = <&hdmi_con>; > - }; > - }; > - > - port@2 { > - reg = <2>; > - adv7513_i2s0: endpoint { > - remote-endpoint = <&sai2a_endpoint>; > - }; > - }; > - }; > - }; > - > - eeprom@53 { > - compatible = "atmel,24c02"; > - reg = <0x53>; > - pagesize = <16>; > - }; > -}; > - > -&iwdg2 { > - timeout-sec = <32>; > - status = "okay"; > -}; > - > -<dc { > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <<dc_pins_d>; > - pinctrl-1 = <<dc_sleep_pins_d>; > - status = "okay"; > - > - port { > - #address-cells = <1>; > - #size-cells = <0>; > - > - ltdc_ep0_out: endpoint@0 { > - reg = <0>; > - remote-endpoint = <&adv7513_in>; > - }; > - }; > -}; > - > -&m_can1 { > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <&m_can1_pins_b>; > - pinctrl-1 = <&m_can1_sleep_pins_b>; > - status = "disabled"; > -}; > - > -&m_can2 { > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <&m_can2_pins_a>; > - pinctrl-1 = <&m_can2_sleep_pins_a>; > - status = "disabled"; > -}; > - > -&pwr_regulators { > - vdd-supply = <&vdd_io>; > - vdd_3v3_usbfs-supply = <&vdd_usb>; > -}; > - > -&qspi { > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; > - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; > - reg = <0x58003000 0x1000>, <0x70000000 0x200000>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "okay"; > - > - flash0: spi-flash@0 { > - compatible = "jedec,spi-nor"; > - reg = <0>; > - spi-rx-bus-width = <4>; > - spi-max-frequency = <108000000>; > - #address-cells = <1>; > - #size-cells = <1>; > - }; > -}; > - > -&rng1 { > - status = "okay"; > -}; > - > -&rtc { > - status = "okay"; > -}; > - > -&sai2 { > - clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <&sai2a_pins_c>; > - pinctrl-1 = <&sai2a_sleep_pins_c>; > - clock-names = "pclk", "x8k", "x11k"; > - status = "okay"; > - > - sai2a: audio-controller@4400b004 { > - #clock-cells = <0>; > - dma-names = "tx"; > - clocks = <&rcc SAI2_K>; > - clock-names = "sai_ck"; > - status = "okay"; > - > - sai2a_port: port { > - sai2a_endpoint: endpoint { > - remote-endpoint = <&adv7513_i2s0>; > - format = "i2s"; > - mclk-fs = <256>; > - }; > - }; > - }; > -}; > - > -&sdmmc1 { > - pinctrl-names = "default", "opendrain", "sleep"; > - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; > - pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; > - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; > - cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > - disable-wp; > - st,sig-dir; > - st,neg-edge; > - st,use-ckin; > - bus-width = <4>; > - vmmc-supply = <&vdd_sd>; > - vqmmc-supply = <&sd_switch>; > - status = "okay"; > -}; > - > -&sdmmc2 { > - pinctrl-names = "default", "opendrain", "sleep"; > - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; > - pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; > - pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; > - bus-width = <8>; > - mmc-ddr-1_8v; > - no-sd; > - no-sdio; > - non-removable; > - st,neg-edge; > - vmmc-supply = <&v3v3>; > - vqmmc-supply = <&vdd_io>; > - status = "okay"; > -}; > - > -&sdmmc3 { > - pinctrl-names = "default", "opendrain", "sleep"; > - pinctrl-0 = <&sdmmc3_b4_pins_b>; > - pinctrl-1 = <&sdmmc3_b4_od_pins_b>; > - pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; > - broken-cd; > - non-removable; > - st,neg-edge; > - bus-width = <4>; > - vmmc-supply = <&wlan_pwr>; > - status = "okay"; > - > - #address-cells = <1>; > - #size-cells = <0>; > - brcmf: bcrmf@1 { > - reg = <1>; > - compatible = "brcm,bcm4329-fmac"; > - }; > -}; > - > -&spi2 { > - pinctrl-names = "default"; > - pinctrl-0 = <&spi2_pins_a>; > - cs-gpios = <&gpioi 0 0>; > - status = "disabled"; > - /delete-property/dmas; > - /delete-property/dma-names; > -}; > - > -&uart4 { > - /* On Low speed expansion header */ > - label = "LS-UART1"; > - pinctrl-names = "default"; > - pinctrl-0 = <&uart4_pins_b>; > - status = "okay"; > -}; > - > -&uart7 { > - /* On Low speed expansion header */ > - label = "LS-UART0"; > - pinctrl-names = "default"; > - pinctrl-0 = <&uart7_pins_a>; > - status = "okay"; > -}; > - > -/* Bluetooth */ > -&usart2 { > - pinctrl-names = "default", "sleep"; > - pinctrl-0 = <&usart2_pins_a>; > - pinctrl-1 = <&usart2_sleep_pins_a>; > - st,hw-flow-ctrl; > - status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <3000000>; > - shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > - }; > -}; > - > -&usbh_ehci { > - phys = <&usbphyc_port0>; > - phy-names = "usb"; > - status = "okay"; > -}; > - > -&usbotg_hs { > - pinctrl-0 = <&usbotg_hs_pins_a>; > - pinctrl-names = "default"; > - phy-names = "usb2-phy"; > - phys = <&usbphyc_port1 0>; > - status = "okay"; > - vbus-supply = <&vbus_otg>; > -}; > - > -&usbphyc { > - status = "okay"; > -}; > - > -&usbphyc_port0 { > - phy-supply = <&vdd_usb>; > - vdda1v1-supply = <®11>; > - vdda1v8-supply = <®18>; > -}; > - > -&usbphyc_port1 { > - phy-supply = <&vdd_usb>; > - vdda1v1-supply = <®11>; > - vdda1v8-supply = <®18>; > -}; > +/* This DT is here only for backward compatibility */ > +#include "stm32mp157a-dhcor-avenger96.dts" > diff --git a/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts > new file mode 100644 > index 000000000000..2e3c9fbb4eb3 > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts > @@ -0,0 +1,38 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + * Copyright (C) 2020 Marek Vasut <marex@denx.de> > + * > + * DHCOR STM32MP1 variant: > + * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG > + * DHCOR PCB number: 586-100 or newer > + * Avenger96 PCB number: 588-200 or newer > + */ > + > +/dts-v1/; > + > +#include "stm32mp157.dtsi" > +#include "stm32mp15xc.dtsi" > +#include "stm32mp15xx-dhcor-som.dtsi" > +#include "stm32mp15xx-dhcor-avenger96.dtsi" > + > +/ { > + model = "Arrow Electronics STM32MP157A Avenger96 board"; > + compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som", > + "st,stm32mp157"; > +}; > + > +&m_can1 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&m_can1_pins_b>; > + pinctrl-1 = <&m_can1_sleep_pins_b>; > + status = "disabled"; > +}; > + > +&m_can2 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&m_can2_pins_a>; > + pinctrl-1 = <&m_can2_sleep_pins_a>; > + status = "disabled"; > +}; > diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi > new file mode 100644 > index 000000000000..930202742a3f > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi > @@ -0,0 +1,401 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + * Copyright (C) 2020 Marek Vasut <marex@denx.de> > + */ > + > +/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */ > +#include "stm32mp15xx-dhcor-io1v8.dtsi" > + > +/ { > + aliases { > + ethernet0 = ðernet0; > + mmc0 = &sdmmc1; > + serial0 = &uart4; > + serial1 = &uart7; > + serial2 = &usart2; > + spi0 = &qspi; > + }; > + > + /* XTal Q1 */ > + cec_clock: clk-cec-fixed { > + #clock-cells = <0>; > + compatible = "fixed-clock"; > + clock-frequency = <24000000>; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + hdmi-out { > + compatible = "hdmi-connector"; > + type = "a"; > + > + port { > + hdmi_con: endpoint { > + remote-endpoint = <&adv7513_out>; > + }; > + }; > + }; > + > + led { > + compatible = "gpio-leds"; > + led1 { > + label = "green:user0"; > + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + default-state = "off"; > + }; > + > + led2 { > + label = "green:user1"; > + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc0"; > + default-state = "off"; > + }; > + > + led3 { > + label = "green:user2"; > + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc1"; > + default-state = "off"; > + }; > + > + led4 { > + label = "green:user3"; > + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "none"; > + default-state = "off"; > + panic-indicator; > + }; > + }; > + > + sd_switch: regulator-sd_switch { > + compatible = "regulator-gpio"; > + regulator-name = "sd_switch"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2900000>; > + regulator-type = "voltage"; > + regulator-always-on; > + > + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; > + gpios-states = <0>; > + states = <1800000 0x1>, > + <2900000 0x0>; > + }; > + > + sound { > + compatible = "audio-graph-card"; > + label = "STM32MP1-AV96-HDMI"; > + dais = <&sai2a_port>; > + status = "okay"; > + }; > + > + wlan_pwr: regulator-wlan { > + compatible = "regulator-fixed"; > + > + regulator-name = "wl-reg"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > +}; > + > +&adc { > + pinctrl-names = "default"; > + pinctrl-0 = <&adc12_ain_pins_b>; > + vdd-supply = <&vdd>; > + vdda-supply = <&vdda>; > + vref-supply = <&vdda>; > + status = "okay"; > + > + adc1: adc@0 { > + st,adc-channels = <0 1 6>; > + st,min-sample-time-nsecs = <5000>; > + status = "okay"; > + }; > + > + adc2: adc@100 { > + st,adc-channels = <0 1 2>; > + st,min-sample-time-nsecs = <5000>; > + status = "okay"; > + }; > +}; > + > +ðernet0 { > + status = "okay"; > + pinctrl-0 = <ðernet0_rgmii_pins_c>; > + pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; > + pinctrl-names = "default", "sleep"; > + phy-mode = "rgmii"; > + max-speed = <1000>; > + phy-handle = <&phy0>; > + > + mdio0 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "snps,dwmac-mdio"; > + reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; > + reset-delay-us = <1000>; > + > + phy0: ethernet-phy@7 { > + reg = <7>; > + > + rxc-skew-ps = <1500>; > + rxdv-skew-ps = <540>; > + rxd0-skew-ps = <420>; > + rxd1-skew-ps = <420>; > + rxd2-skew-ps = <420>; > + rxd3-skew-ps = <420>; > + > + txc-skew-ps = <1440>; > + txen-skew-ps = <540>; > + txd0-skew-ps = <420>; > + txd1-skew-ps = <420>; > + txd2-skew-ps = <420>; > + txd3-skew-ps = <420>; > + }; > + }; > +}; > + > +&i2c1 { /* X6 I2C1 */ > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins_b>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c2 { /* X6 I2C2 */ > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins_c>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&i2c4 { > + hdmi-transmitter@3d { > + compatible = "adi,adv7513"; > + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; > + reg-names = "main", "cec", "edid", "packet"; > + clocks = <&cec_clock>; > + clock-names = "cec"; > + > + avdd-supply = <&v3v3>; > + dvdd-supply = <&v3v3>; > + pvdd-supply = <&v3v3>; > + dvdd-3v-supply = <&v3v3>; > + bgvdd-supply = <&v3v3>; > + > + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; > + interrupt-parent = <&gpiog>; > + > + status = "okay"; > + > + adi,input-depth = <8>; > + adi,input-colorspace = "rgb"; > + adi,input-clock = "1x"; > + adi,input-style = <1>; > + adi,input-justification = "evenly"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + adv7513_in: endpoint { > + remote-endpoint = <<dc_ep0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + adv7513_out: endpoint { > + remote-endpoint = <&hdmi_con>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + adv7513_i2s0: endpoint { > + remote-endpoint = <&sai2a_endpoint>; > + }; > + }; > + }; > + }; > +}; > + > +<dc { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <<dc_pins_d>; > + pinctrl-1 = <<dc_sleep_pins_d>; > + status = "okay"; > + > + port { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ltdc_ep0_out: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&adv7513_in>; > + }; > + }; > +}; > + > +&sai2 { > + clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sai2a_pins_c>; > + pinctrl-1 = <&sai2a_sleep_pins_c>; > + clock-names = "pclk", "x8k", "x11k"; > + status = "okay"; > + > + sai2a: audio-controller@4400b004 { > + #clock-cells = <0>; > + dma-names = "tx"; > + clocks = <&rcc SAI2_K>; > + clock-names = "sai_ck"; > + status = "okay"; > + > + sai2a_port: port { > + sai2a_endpoint: endpoint { > + remote-endpoint = <&adv7513_i2s0>; > + format = "i2s"; > + mclk-fs = <256>; > + }; > + }; > + }; > +}; > + > +&sdmmc1 { > + pinctrl-names = "default", "opendrain", "sleep"; > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; > + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; > + cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > + disable-wp; > + st,sig-dir; > + st,neg-edge; > + st,use-ckin; > + bus-width = <4>; > + vmmc-supply = <&vdd_sd>; > + vqmmc-supply = <&sd_switch>; > + status = "okay"; > +}; > + > +&sdmmc2 { > + pinctrl-names = "default", "opendrain", "sleep"; > + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; > + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; > + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; > + bus-width = <8>; > + mmc-ddr-1_8v; > + no-sd; > + no-sdio; > + non-removable; > + st,neg-edge; > + vmmc-supply = <&v3v3>; > + vqmmc-supply = <&vdd_io>; > + status = "okay"; > +}; > + > +&sdmmc3 { > + pinctrl-names = "default", "opendrain", "sleep"; > + pinctrl-0 = <&sdmmc3_b4_pins_b>; > + pinctrl-1 = <&sdmmc3_b4_od_pins_b>; > + pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; > + broken-cd; > + non-removable; > + st,neg-edge; > + bus-width = <4>; > + vmmc-supply = <&wlan_pwr>; > + status = "okay"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + brcmf: bcrmf@1 { > + reg = <1>; > + compatible = "brcm,bcm4329-fmac"; > + }; > +}; > + > +&spi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi2_pins_a>; > + cs-gpios = <&gpioi 0 0>; > + status = "disabled"; > + /delete-property/dmas; > + /delete-property/dma-names; > +}; > + > +&uart4 { > + /* On Low speed expansion header */ > + label = "LS-UART1"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart4_pins_b>; > + status = "okay"; > +}; > + > +&uart7 { > + /* On Low speed expansion header */ > + label = "LS-UART0"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart7_pins_a>; > + status = "okay"; > +}; > + > +/* Bluetooth */ > +&usart2 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&usart2_pins_a>; > + pinctrl-1 = <&usart2_sleep_pins_a>; > + st,hw-flow-ctrl; > + status = "okay"; > + > + bluetooth { > + compatible = "brcm,bcm43438-bt"; > + max-speed = <3000000>; > + shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +&usbh_ehci { > + phys = <&usbphyc_port0>; > + phy-names = "usb"; > + status = "okay"; > +}; > + > +&usbotg_hs { > + pinctrl-0 = <&usbotg_hs_pins_a>; > + pinctrl-names = "default"; > + phy-names = "usb2-phy"; > + phys = <&usbphyc_port1 0>; > + status = "okay"; > + vbus-supply = <&vbus_otg>; > +}; > + > +&usbphyc { > + status = "okay"; > +}; > + > +&usbphyc_port0 { > + phy-supply = <&vdd_usb>; > + vdda1v1-supply = <®11>; > + vdda1v8-supply = <®18>; > +}; > + > +&usbphyc_port1 { > + phy-supply = <&vdd_usb>; > + vdda1v1-supply = <®11>; > + vdda1v8-supply = <®18>; > +}; > diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi > new file mode 100644 > index 000000000000..75172314d7af > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi > @@ -0,0 +1,23 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + * Copyright (C) 2020 Marek Vasut <marex@denx.de> > + */ > + > +/ { > + /* Enpirion EP3A8LQI U2 on the DHCOR */ > + vdd_io: regulator-buck-io { > + compatible = "regulator-fixed"; > + regulator-name = "buck-io"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-boot-on; > + vin-supply = <&vdd>; > + }; > +}; > + > +&pwr_regulators { > + vdd-supply = <&vdd_io>; > +}; > diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi > new file mode 100644 > index 000000000000..04fbb324a541 > --- /dev/null > +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi > @@ -0,0 +1,209 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) > +/* > + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + * Copyright (C) 2020 Marek Vasut <marex@denx.de> > + */ > + > +#include "stm32mp15-pinctrl.dtsi" > +#include "stm32mp15xxac-pinctrl.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/mfd/st,stpmic1.h> > + > +/ { > + aliases { > + spi0 = &qspi; > + }; > + > + memory@c0000000 { > + device_type = "memory"; > + reg = <0xc0000000 0x40000000>; > + }; > +}; > + > +&i2c4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c4_pins_a>; > + i2c-scl-rising-time-ns = <185>; > + i2c-scl-falling-time-ns = <20>; > + status = "okay"; > + /delete-property/dmas; > + /delete-property/dma-names; > + > + pmic: stpmic@33 { > + compatible = "st,stpmic1"; > + reg = <0x33>; > + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; > + interrupt-controller; > + #interrupt-cells = <2>; > + status = "okay"; > + > + regulators { > + compatible = "st,stpmic1-regulators"; > + > + ldo1-supply = <&v3v3>; > + ldo2-supply = <&v3v3>; > + ldo3-supply = <&vdd_ddr>; > + ldo5-supply = <&v3v3>; > + ldo6-supply = <&v3v3>; > + pwr_sw1-supply = <&bst_out>; > + pwr_sw2-supply = <&bst_out>; > + > + vddcore: buck1 { > + regulator-name = "vddcore"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd_ddr: buck2 { > + regulator-name = "vdd_ddr"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + vdd: buck3 { > + regulator-name = "vdd"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + regulator-always-on; > + regulator-initial-mode = <0>; > + regulator-over-current-protection; > + }; > + > + v3v3: buck4 { > + regulator-name = "v3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-over-current-protection; > + regulator-initial-mode = <0>; > + }; > + > + vdda: ldo1 { > + regulator-name = "vdda"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO1 0>; > + }; > + > + v2v8: ldo2 { > + regulator-name = "v2v8"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + interrupts = <IT_CURLIM_LDO2 0>; > + }; > + > + vtt_ddr: ldo3 { > + regulator-name = "vtt_ddr"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <750000>; > + regulator-always-on; > + regulator-over-current-protection; > + }; > + > + vdd_usb: ldo4 { > + regulator-name = "vdd_usb"; > + interrupts = <IT_CURLIM_LDO4 0>; > + }; > + > + vdd_sd: ldo5 { > + regulator-name = "vdd_sd"; > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + interrupts = <IT_CURLIM_LDO5 0>; > + regulator-boot-on; > + }; > + > + v1v8: ldo6 { > + regulator-name = "v1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + interrupts = <IT_CURLIM_LDO6 0>; > + regulator-enable-ramp-delay = <300000>; > + }; > + > + vref_ddr: vref_ddr { > + regulator-name = "vref_ddr"; > + regulator-always-on; > + }; > + > + bst_out: boost { > + regulator-name = "bst_out"; > + interrupts = <IT_OCP_BOOST 0>; > + }; > + > + vbus_otg: pwr_sw1 { > + regulator-name = "vbus_otg"; > + interrupts = <IT_OCP_OTG 0>; > + regulator-active-discharge = <1>; > + }; > + > + vbus_sw: pwr_sw2 { > + regulator-name = "vbus_sw"; > + interrupts = <IT_OCP_SWOUT 0>; > + regulator-active-discharge = <1>; > + }; > + }; > + > + onkey { > + compatible = "st,stpmic1-onkey"; > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; > + interrupt-names = "onkey-falling", "onkey-rising"; > + status = "okay"; > + }; > + > + watchdog { > + compatible = "st,stpmic1-wdt"; > + status = "disabled"; > + }; > + }; > + > + eeprom@53 { > + compatible = "atmel,24c02"; > + reg = <0x53>; > + pagesize = <16>; > + }; > +}; > + > +&iwdg2 { > + timeout-sec = <32>; > + status = "okay"; > +}; > + > +&pwr_regulators { > + vdd-supply = <&vdd>; > + vdd_3v3_usbfs-supply = <&vdd_usb>; > +}; > + > +&qspi { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; > + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; > + reg = <0x58003000 0x1000>, <0x70000000 0x200000>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + flash0: spi-flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-rx-bus-width = <4>; > + spi-max-frequency = <108000000>; > + #address-cells = <1>; > + #size-cells = <1>; > + }; > +}; > + > +&rng1 { > + status = "okay"; > +}; > + > +&rtc { > + status = "okay"; > +}; > -- > 2.25.1 > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board 2020-05-13 18:10 ` [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut 2020-05-14 5:18 ` Manivannan Sadhasivam @ 2020-05-14 14:27 ` Alexandre Torgue 1 sibling, 0 replies; 6+ messages in thread From: Alexandre Torgue @ 2020-05-14 14:27 UTC (permalink / raw) To: Marek Vasut, linux-arm-kernel Cc: Patrick Delaunay, linux-stm32, Patrice Chotard, Maxime Coquelin, Manivannan Sadhasivam Hi Marek On 5/13/20 8:10 PM, Marek Vasut wrote: > The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top > of an Avenger96 reference board. The DHCOR SoM can be populated with any > STM32MP15xx. Split the DTs to reflect this such that the common SoM and > Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example > implementation of STM32MP157A SoM and Avenger96 board is separated into > stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for > the sake of backward naming compatibility. > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Alexandre Torgue <alexandre.torgue@st.com> > Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> > Cc: Patrice Chotard <patrice.chotard@st.com> > Cc: Patrick Delaunay <patrick.delaunay@st.com> > Cc: linux-stm32@st-md-mailman.stormreply.com > To: linux-arm-kernel@lists.infradead.org > --- > V2: - Drop the stm32mp157a-dhcor-som.dtsi , as it was just include statements > - Add comment about what SoM+Board combination is currently supported > V3: No change > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/stm32mp157a-avenger96.dts | 618 +----------------- > .../boot/dts/stm32mp157a-dhcor-avenger96.dts | 38 ++ > .../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 401 ++++++++++++ > .../arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi | 23 + > arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 209 ++++++ > 6 files changed, 675 insertions(+), 615 deletions(-) > create mode 100644 arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dts > create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi > create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi > create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi > Series applied on stm32-next. Regards Alex _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-05-14 14:27 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-05-13 18:10 [PATCH V3 1/4] ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2 Marek Vasut 2020-05-13 18:10 ` [PATCH V3 2/4] ARM: dts: stm32: Add GPIO LEDs " Marek Vasut 2020-05-13 18:10 ` [PATCH V3 3/4] ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2 Marek Vasut 2020-05-13 18:10 ` [PATCH V3 4/4] ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board Marek Vasut 2020-05-14 5:18 ` Manivannan Sadhasivam 2020-05-14 14:27 ` Alexandre Torgue
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.