All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v9 1/2] drm/panel: Add support for Truly NT35597 panel driver
@ 2018-09-29  0:38 Abhinav Kumar
  2018-09-29  0:38 ` [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings Abhinav Kumar
  0 siblings, 1 reply; 6+ messages in thread
From: Abhinav Kumar @ 2018-09-29  0:38 UTC (permalink / raw)
  To: dri-devel
  Cc: thierry.reding, linux-arm-msm, Abhinav Kumar, robh+dt, seanpaul,
	hoegsberg, chandanu

Add support for Truly NT35597 panel driver used in MSM reference
platforms. This panel driver supports both single DSI and dual
DSI modes.

However, this patch series adds support only for dual DSI mode.

Changes in v9:
- Sorted headers alphabetically
- Remove void type for commands
- Reduce number of lines used by comments
- Fix return value in probe
- Fix driver name to use '-' instead of '_'

Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
---
 drivers/gpu/drm/panel/Kconfig               |   7 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-truly-nt35597.c | 675 ++++++++++++++++++++++++++++
 3 files changed, 683 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 6020c30..073ffa0 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
 	  Say Y here if you want to enable support for the Sitronix
 	  ST7789V controller for 240x320 LCD panels
 
+config DRM_PANEL_TRULY_NT35597_WQXGA
+	tristate "Truly WQXGA"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
+	  Video Mode panel
 endmenu
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 5ccaaa9..80fd19f 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
+obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
diff --git a/drivers/gpu/drm/panel/panel-truly-nt35597.c b/drivers/gpu/drm/panel/panel-truly-nt35597.c
new file mode 100644
index 0000000..fc2a66c
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-truly-nt35597.c
@@ -0,0 +1,675 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_mipi_dsi.h>
+
+#include <linux/gpio/consumer.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/mipi_display.h>
+
+static const char * const regulator_names[] = {
+	"vdda",
+	"vdispp",
+	"vdispn",
+};
+
+static unsigned long const regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000,
+};
+
+static unsigned long const regulator_disable_loads[] = {
+	80,
+	100,
+	100,
+};
+
+struct cmd_set {
+	u8 commands[4];
+	u8 size;
+};
+
+struct nt35597_config {
+	u32 width_mm;
+	u32 height_mm;
+	const char *panel_name;
+	const struct cmd_set *panel_on_cmds;
+	u32 num_on_cmds;
+	const struct drm_display_mode *dm;
+};
+
+struct truly_nt35597 {
+	struct device *dev;
+	struct drm_panel panel;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *mode_gpio;
+
+	struct backlight_device *backlight;
+
+	struct mipi_dsi_device *dsi[2];
+
+	const struct nt35597_config *config;
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel *panel)
+{
+	return container_of(panel, struct truly_nt35597, panel);
+}
+
+static const struct cmd_set qcom_2k_panel_magic_cmds[] = {
+	/* CMD2_P0 */
+	{ { 0xff, 0x20 }, 2 },
+	{ { 0xfb, 0x01 }, 2 },
+	{ { 0x00, 0x01 }, 2 },
+	{ { 0x01, 0x55 }, 2 },
+	{ { 0x02, 0x45 }, 2 },
+	{ { 0x05, 0x40 }, 2 },
+	{ { 0x06, 0x19 }, 2 },
+	{ { 0x07, 0x1e }, 2 },
+	{ { 0x0b, 0x73 }, 2 },
+	{ { 0x0c, 0x73 }, 2 },
+	{ { 0x0e, 0xb0 }, 2 },
+	{ { 0x0f, 0xae }, 2 },
+	{ { 0x11, 0xb8 }, 2 },
+	{ { 0x13, 0x00 }, 2 },
+	{ { 0x58, 0x80 }, 2 },
+	{ { 0x59, 0x01 }, 2 },
+	{ { 0x5a, 0x00 }, 2 },
+	{ { 0x5b, 0x01 }, 2 },
+	{ { 0x5c, 0x80 }, 2 },
+	{ { 0x5d, 0x81 }, 2 },
+	{ { 0x5e, 0x00 }, 2 },
+	{ { 0x5f, 0x01 }, 2 },
+	{ { 0x72, 0x11 }, 2 },
+	{ { 0x68, 0x03 }, 2 },
+	/* CMD2_P4 */
+	{ { 0xFF, 0x24 }, 2 },
+	{ { 0xFB, 0x01 }, 2 },
+	{ { 0x00, 0x1C }, 2 },
+	{ { 0x01, 0x0B }, 2 },
+	{ { 0x02, 0x0C }, 2 },
+	{ { 0x03, 0x01 }, 2 },
+	{ { 0x04, 0x0F }, 2 },
+	{ { 0x05, 0x10 }, 2 },
+	{ { 0x06, 0x10 }, 2 },
+	{ { 0x07, 0x10 }, 2 },
+	{ { 0x08, 0x89 }, 2 },
+	{ { 0x09, 0x8A }, 2 },
+	{ { 0x0A, 0x13 }, 2 },
+	{ { 0x0B, 0x13 }, 2 },
+	{ { 0x0C, 0x15 }, 2 },
+	{ { 0x0D, 0x15 }, 2 },
+	{ { 0x0E, 0x17 }, 2 },
+	{ { 0x0F, 0x17 }, 2 },
+	{ { 0x10, 0x1C }, 2 },
+	{ { 0x11, 0x0B }, 2 },
+	{ { 0x12, 0x0C }, 2 },
+	{ { 0x13, 0x01 }, 2 },
+	{ { 0x14, 0x0F }, 2 },
+	{ { 0x15, 0x10 }, 2 },
+	{ { 0x16, 0x10 }, 2 },
+	{ { 0x17, 0x10 }, 2 },
+	{ { 0x18, 0x89 }, 2 },
+	{ { 0x19, 0x8A }, 2 },
+	{ { 0x1A, 0x13 }, 2 },
+	{ { 0x1B, 0x13 }, 2 },
+	{ { 0x1C, 0x15 }, 2 },
+	{ { 0x1D, 0x15 }, 2 },
+	{ { 0x1E, 0x17 }, 2 },
+	{ { 0x1F, 0x17 }, 2 },
+	/* STV */
+	{ { 0x20, 0x40 }, 2 },
+	{ { 0x21, 0x01 }, 2 },
+	{ { 0x22, 0x00 }, 2 },
+	{ { 0x23, 0x40 }, 2 },
+	{ { 0x24, 0x40 }, 2 },
+	{ { 0x25, 0x6D }, 2 },
+	{ { 0x26, 0x40 }, 2 },
+	{ { 0x27, 0x40 }, 2 },
+	/* Vend */
+	{ { 0xE0, 0x00 }, 2 },
+	{ { 0xDC, 0x21 }, 2 },
+	{ { 0xDD, 0x22 }, 2 },
+	{ { 0xDE, 0x07 }, 2 },
+	{ { 0xDF, 0x07 }, 2 },
+	{ { 0xE3, 0x6D }, 2 },
+	{ { 0xE1, 0x07 }, 2 },
+	{ { 0xE2, 0x07 }, 2 },
+	/* UD */
+	{ { 0x29, 0xD8 }, 2 },
+	{ { 0x2A, 0x2A }, 2 },
+	/* CLK */
+	{ { 0x4B, 0x03 }, 2 },
+	{ { 0x4C, 0x11 }, 2 },
+	{ { 0x4D, 0x10 }, 2 },
+	{ { 0x4E, 0x01 }, 2 },
+	{ { 0x4F, 0x01 }, 2 },
+	{ { 0x50, 0x10 }, 2 },
+	{ { 0x51, 0x00 }, 2 },
+	{ { 0x52, 0x80 }, 2 },
+	{ { 0x53, 0x00 }, 2 },
+	{ { 0x56, 0x00 }, 2 },
+	{ { 0x54, 0x07 }, 2 },
+	{ { 0x58, 0x07 }, 2 },
+	{ { 0x55, 0x25 }, 2 },
+	/* Reset XDONB */
+	{ { 0x5B, 0x43 }, 2 },
+	{ { 0x5C, 0x00 }, 2 },
+	{ { 0x5F, 0x73 }, 2 },
+	{ { 0x60, 0x73 }, 2 },
+	{ { 0x63, 0x22 }, 2 },
+	{ { 0x64, 0x00 }, 2 },
+	{ { 0x67, 0x08 }, 2 },
+	{ { 0x68, 0x04 }, 2 },
+	/* Resolution:1440x2560 */
+	{ { 0x72, 0x02 }, 2 },
+	/* mux */
+	{ { 0x7A, 0x80 }, 2 },
+	{ { 0x7B, 0x91 }, 2 },
+	{ { 0x7C, 0xD8 }, 2 },
+	{ { 0x7D, 0x60 }, 2 },
+	{ { 0x7F, 0x15 }, 2 },
+	{ { 0x75, 0x15 }, 2 },
+	/* ABOFF */
+	{ { 0xB3, 0xC0 }, 2 },
+	{ { 0xB4, 0x00 }, 2 },
+	{ { 0xB5, 0x00 }, 2 },
+	/* Source EQ */
+	{ { 0x78, 0x00 }, 2 },
+	{ { 0x79, 0x00 }, 2 },
+	{ { 0x80, 0x00 }, 2 },
+	{ { 0x83, 0x00 }, 2 },
+	/* FP BP */
+	{ { 0x93, 0x0A }, 2 },
+	{ { 0x94, 0x0A }, 2 },
+	/* Inversion Type */
+	{ { 0x8A, 0x00 }, 2 },
+	{ { 0x9B, 0xFF }, 2 },
+	/* IMGSWAP =1 @PortSwap=1 */
+	{ { 0x9D, 0xB0 }, 2 },
+	{ { 0x9F, 0x63 }, 2 },
+	{ { 0x98, 0x10 }, 2 },
+	/* FRM */
+	{ { 0xEC, 0x00 }, 2 },
+	/* CMD1 */
+	{ { 0xFF, 0x10 }, 2 },
+	/* VBP+VSA=,VFP = 10H */
+	{ { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
+	/* FTE on */
+	{ { 0x35, 0x00 }, 2 },
+	/* EN_BK =1(auto black) */
+	{ { 0xE5, 0x01 }, 2 },
+	/* CMD mode(10) VDO mode(03) */
+	{ { 0xBB, 0x03 }, 2 },
+	/* Non Reload MTP */
+	{ { 0xFB, 0x01 }, 2 },
+};
+
+static int truly_dcs_write(struct drm_panel *panel, u32 command)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write(ctx->dsi[i], command, NULL, 0);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd 0x%x failed for dsi = %d\n",
+				command, i);
+		}
+	}
+
+	return ret;
+}
+
+static int truly_dcs_write_buf(struct drm_panel *panel,
+	u32 size, const u8 *buf)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], buf, size);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"failed to tx cmd [%d], err: %d\n", i, ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int truly_35597_power_on(struct truly_nt35597 *ctx)
+{
+	int ret, i;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+					regulator_enable_loads[i]);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Reset sequence of truly panel requires the panel to be
+	 * out of reset for 10ms, followed by being held in reset
+	 * for 10ms and then out again
+	 */
+	gpiod_set_value(ctx->reset_gpio, 0);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 1);
+	usleep_range(10000, 20000);
+	gpiod_set_value(ctx->reset_gpio, 0);
+
+	return 0;
+}
+
+static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
+{
+	int ret = 0;
+	int i;
+
+	gpiod_set_value(ctx->reset_gpio, 1);
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+				regulator_disable_loads[i]);
+		if (ret) {
+			DRM_DEV_ERROR(ctx->dev,
+				"regulator_set_load failed %d\n", ret);
+			return ret;
+		}
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret) {
+		DRM_DEV_ERROR(ctx->dev,
+			"regulator_bulk_disable failed %d\n", ret);
+	}
+	return ret;
+}
+
+static int truly_nt35597_disable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (!ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_disable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
+				ret);
+	}
+
+	ctx->enabled = false;
+	return 0;
+}
+
+static int truly_nt35597_unprepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret = 0;
+
+	if (!ctx->prepared)
+		return 0;
+
+	ctx->dsi[0]->mode_flags = 0;
+	ctx->dsi[1]->mode_flags = 0;
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_off cmd failed ret = %d\n",
+			ret);
+	}
+
+	/* 120ms delay required here as per DCS spec */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"enter_sleep cmd failed ret = %d\n", ret);
+	}
+
+	ret = truly_nt35597_power_off(ctx);
+	if (ret < 0)
+		DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
+
+	ctx->prepared = false;
+	return ret;
+}
+
+static int truly_nt35597_prepare(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+	int i;
+	const struct cmd_set *panel_on_cmds;
+	const struct nt35597_config *config;
+	u32 num_cmds;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = truly_35597_power_on(ctx);
+	if (ret < 0)
+		return ret;
+
+	ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
+	ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	config = ctx->config;
+	panel_on_cmds = config->panel_on_cmds;
+	num_cmds = config->num_on_cmds;
+
+	for (i = 0; i < num_cmds; i++) {
+		ret = truly_dcs_write_buf(panel,
+				panel_on_cmds[i].size,
+					panel_on_cmds[i].commands);
+		if (ret < 0) {
+			DRM_DEV_ERROR(ctx->dev,
+				"cmd set tx failed i = %d ret = %d\n",
+					i, ret);
+			goto power_off;
+		}
+	}
+
+	ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"exit_sleep_mode cmd failed ret = %d\n",
+			ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending exit sleep DCS command */
+	msleep(120);
+
+	ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev,
+			"set_display_on cmd failed ret = %d\n", ret);
+		goto power_off;
+	}
+
+	/* Per DSI spec wait 120ms after sending set_display_on DCS command */
+	msleep(120);
+
+	ctx->prepared = true;
+
+	return 0;
+
+power_off:
+	if (truly_nt35597_power_off(ctx))
+		DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
+	return ret;
+}
+
+static int truly_nt35597_enable(struct drm_panel *panel)
+{
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	int ret;
+
+	if (ctx->enabled)
+		return 0;
+
+	if (ctx->backlight) {
+		ret = backlight_enable(ctx->backlight);
+		if (ret < 0)
+			DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
+						  ret);
+	}
+
+	ctx->enabled = true;
+
+	return 0;
+}
+
+static int truly_nt35597_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct truly_nt35597 *ctx = panel_to_ctx(panel);
+	struct drm_display_mode *mode;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	mode = drm_mode_create(connector->dev);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev,
+			"failed to create a new display mode\n");
+		return 0;
+	}
+
+	connector->display_info.width_mm = config->width_mm;
+	connector->display_info.height_mm = config->height_mm;
+	drm_mode_copy(mode, config->dm);
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
+	.disable = truly_nt35597_disable,
+	.unprepare = truly_nt35597_unprepare,
+	.prepare = truly_nt35597_prepare,
+	.enable = truly_nt35597_enable,
+	.get_modes = truly_nt35597_get_modes,
+};
+
+static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
+{
+	struct device *dev = ctx->dev;
+	int ret, i;
+	const struct nt35597_config *config;
+
+	config = ctx->config;
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
+			PTR_ERR(ctx->reset_gpio));
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->mode_gpio)) {
+		DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
+			PTR_ERR(ctx->mode_gpio));
+		return PTR_ERR(ctx->mode_gpio);
+	}
+
+	/* dual port */
+	gpiod_set_value(ctx->mode_gpio, 0);
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = dev;
+	ctx->panel.funcs = &truly_nt35597_drm_funcs;
+	drm_panel_add(&ctx->panel);
+
+	return 0;
+}
+
+static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
+	.name = "1440x2560",
+	.clock = 268316,
+	.hdisplay = 1440,
+	.hsync_start = 1440 + 200,
+	.hsync_end = 1440 + 200 + 32,
+	.htotal = 1440 + 200 + 32 + 64,
+	.vdisplay = 2560,
+	.vsync_start = 2560 + 8,
+	.vsync_end = 2560 + 8 + 1,
+	.vtotal = 2560 + 8 + 1 + 7,
+	.vrefresh = 60,
+	.flags = 0,
+};
+
+static const struct nt35597_config nt35597_dir = {
+	.width_mm = 74,
+	.height_mm = 131,
+	.panel_name = "qcom_sdm845_mtp_2k_panel",
+	.dm = &qcom_sdm845_mtp_2k_mode,
+	.panel_on_cmds = qcom_2k_panel_magic_cmds,
+	.num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
+};
+
+static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct truly_nt35597 *ctx;
+	struct mipi_dsi_device *dsi1_device;
+	struct device_node *dsi1;
+	struct mipi_dsi_host *dsi1_host;
+	struct mipi_dsi_device *dsi_dev;
+	int ret = 0;
+	int i;
+
+	const struct mipi_dsi_device_info info = {
+		.type = "trulynt35597",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+
+	if (!ctx)
+		return -ENOMEM;
+
+	/*
+	 * This device represents itself as one with two input ports which are
+	 * fed by the output ports of the two DSI controllers . The DSI0 is
+	 * the master controller and has most of the panel related info in its
+	 * child node.
+	 */
+
+	ctx->config = of_device_get_match_data(dev);
+
+	if (!ctx->config) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+	if (!dsi1) {
+		DRM_DEV_ERROR(dev,
+			"failed to get remote node for dsi1_device\n");
+		return -ENODEV;
+	}
+
+	dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
+	of_node_put(dsi1);
+	if (!dsi1_host) {
+		DRM_DEV_ERROR(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	/* register the second DSI device */
+	dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
+	if (IS_ERR(dsi1_device)) {
+		DRM_DEV_ERROR(dev, "failed to create dsi device\n");
+		return PTR_ERR(dsi1_device);
+	}
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	ctx->dev = dev;
+	ctx->dsi[0] = dsi;
+	ctx->dsi[1] = dsi1_device;
+
+	ret = truly_nt35597_panel_add(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to add panel\n");
+		goto err_panel_add;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
+		dsi_dev = ctx->dsi[i];
+		dsi_dev->lanes = 4;
+		dsi_dev->format = MIPI_DSI_FMT_RGB888;
+		dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
+			MIPI_DSI_CLOCK_NON_CONTINUOUS;
+		ret = mipi_dsi_attach(dsi_dev);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dev,
+				"dsi attach failed i = %d\n", i);
+			goto err_dsi_attach;
+		}
+	}
+
+	return 0;
+
+err_dsi_attach:
+	drm_panel_remove(&ctx->panel);
+err_panel_add:
+	mipi_dsi_device_unregister(dsi1_device);
+	return ret;
+}
+
+static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
+{
+	struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	if (ctx->dsi[0])
+		mipi_dsi_detach(ctx->dsi[0]);
+	if (ctx->dsi[1]) {
+		mipi_dsi_detach(ctx->dsi[1]);
+		mipi_dsi_device_unregister(ctx->dsi[1]);
+	}
+
+	drm_panel_remove(&ctx->panel);
+	return 0;
+}
+
+static const struct of_device_id truly_nt35597_of_match[] = {
+	{
+		.compatible = "truly,nt35597-2K-display",
+		.data = &nt35597_dir,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
+
+static struct mipi_dsi_driver truly_nt35597_driver = {
+	.driver = {
+		.name = "panel-truly-nt35597",
+		.of_match_table = truly_nt35597_of_match,
+	},
+	.probe = truly_nt35597_probe,
+	.remove = truly_nt35597_remove,
+};
+module_mipi_dsi_driver(truly_nt35597_driver);
+
+MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
+MODULE_LICENSE("GPL v2");
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

^ permalink raw reply related	[flat|nested] 6+ messages in thread

* [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings
  2018-09-29  0:38 [PATCH v9 1/2] drm/panel: Add support for Truly NT35597 panel driver Abhinav Kumar
@ 2018-09-29  0:38 ` Abhinav Kumar
  2018-10-04 19:01   ` Rob Herring
  0 siblings, 1 reply; 6+ messages in thread
From: Abhinav Kumar @ 2018-09-29  0:38 UTC (permalink / raw)
  To: dri-devel
  Cc: thierry.reding, linux-arm-msm, Abhinav Kumar, robh+dt, seanpaul,
	hoegsberg, chandanu

Add the device tree bindings for Truly NT35597 panel driver. This panel
driver supports both single DSI and dual DSI.

However, this patch series supports only dual DSI.

Changes in v9:
  - None

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
---
 .../devicetree/bindings/display/truly,nt35597.txt  | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/truly,nt35597.txt

diff --git a/Documentation/devicetree/bindings/display/truly,nt35597.txt b/Documentation/devicetree/bindings/display/truly,nt35597.txt
new file mode 100644
index 0000000..46b29eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/truly,nt35597.txt
@@ -0,0 +1,60 @@
+Truly model NT35597 DSI display driver
+
+The Truly NT35597 is a generic display driver, currently only configured
+for use in the 2K display on the Qualcomm SDM845.
+
+Required properties:
+- compatible: should be "truly,nt35597-2K-display"
+- vdda-supply: phandle of the regulator that provides the supply voltage
+  Power IC supply
+- vdispp-supply: phandle of the regulator that provides the supply voltage
+  for positive LCD bias
+- vdispn-supply: phandle of the regulator that provides the supply voltage
+  for negative LCD bias
+- reset-gpios: phandle of gpio for reset line
+  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
+  (active low)
+- mode-gpios: phandle of the gpio for choosing the mode of the display
+  for single DSI or Dual DSI
+  (active high)
+  This should be low for dual DSI and high for single DSI mode
+- ports: This device has two video ports driven by two DSIs. Their connections
+  are modelled using the OF graph bindings specified in
+  Documentation/devicetree/bindings/graph.txt.
+  - port@0: DSI input port driven by master DSI
+  - port@1: DSI input port driven by secondary DSI
+
+Example:
+
+	dsi@ae94000 {
+		panel@0 {
+			compatible = "truly,nt35597-2K-display";
+			reg = <0>;
+			vdda-supply = <&pm8998_l14>;
+			vdispp-supply = <&lab_regulator>;
+			vdispn-supply = <&ibb_regulator>;
+			pinctrl-names = "default", "suspend";
+			pinctrl-0 = <&dpu_dsi_active>;
+			pinctrl-1 = <&dpu_dsi_suspend>;
+
+			reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+			mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					panel0_in: endpoint {
+						remote-endpoint = <&dsi0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					panel1_in: endpoint {
+						remote-endpoint = <&dsi1_out>;
+					};
+				};
+			};
+		};
+	};
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

^ permalink raw reply related	[flat|nested] 6+ messages in thread

* Re: [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings
  2018-09-29  0:38 ` [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings Abhinav Kumar
@ 2018-10-04 19:01   ` Rob Herring
  2018-10-04 19:42     ` Abhinav Kumar
  0 siblings, 1 reply; 6+ messages in thread
From: Rob Herring @ 2018-10-04 19:01 UTC (permalink / raw)
  To: abhinavk
  Cc: Thierry Reding, linux-arm-msm, dri-devel, Sean Paul,
	Kristian H . Kristensen, chandanu

If you want DT bindings reviewed, you have to cc the DT list. (Or wait
for Sean Paul to ping me on IRC)

On Fri, Sep 28, 2018 at 7:39 PM Abhinav Kumar <abhinavk@codeaurora.org> wrote:
>
> Add the device tree bindings for Truly NT35597 panel driver. This panel
> driver supports both single DSI and dual DSI.

By driver, you means drives panel timing signals or a Linux driver?
The former is okay, the latter is not.

>
> However, this patch series supports only dual DSI.
>
> Changes in v9:
>   - None
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Sean Paul <seanpaul@chromium.org>
> Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
> ---
>  .../devicetree/bindings/display/truly,nt35597.txt  | 60 ++++++++++++++++++++++
>  1 file changed, 60 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/truly,nt35597.txt
>
> diff --git a/Documentation/devicetree/bindings/display/truly,nt35597.txt b/Documentation/devicetree/bindings/display/truly,nt35597.txt
> new file mode 100644
> index 0000000..46b29eb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/truly,nt35597.txt
> @@ -0,0 +1,60 @@
> +Truly model NT35597 DSI display driver
> +
> +The Truly NT35597 is a generic display driver, currently only configured
> +for use in the 2K display on the Qualcomm SDM845.

So this is for *all* SDM845 based boards?

> +
> +Required properties:
> +- compatible: should be "truly,nt35597-2K-display"
> +- vdda-supply: phandle of the regulator that provides the supply voltage
> +  Power IC supply
> +- vdispp-supply: phandle of the regulator that provides the supply voltage
> +  for positive LCD bias
> +- vdispn-supply: phandle of the regulator that provides the supply voltage
> +  for negative LCD bias
> +- reset-gpios: phandle of gpio for reset line
> +  This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
> +  (active low)
> +- mode-gpios: phandle of the gpio for choosing the mode of the display
> +  for single DSI or Dual DSI
> +  (active high)

active high doesn't really make sense for this.

> +  This should be low for dual DSI and high for single DSI mode
> +- ports: This device has two video ports driven by two DSIs. Their connections
> +  are modelled using the OF graph bindings specified in

modeled

> +  Documentation/devicetree/bindings/graph.txt.
> +  - port@0: DSI input port driven by master DSI
> +  - port@1: DSI input port driven by secondary DSI
> +
> +Example:
> +
> +       dsi@ae94000 {
> +               panel@0 {
> +                       compatible = "truly,nt35597-2K-display";
> +                       reg = <0>;
> +                       vdda-supply = <&pm8998_l14>;
> +                       vdispp-supply = <&lab_regulator>;
> +                       vdispn-supply = <&ibb_regulator>;
> +                       pinctrl-names = "default", "suspend";
> +                       pinctrl-0 = <&dpu_dsi_active>;
> +                       pinctrl-1 = <&dpu_dsi_suspend>;
> +
> +                       reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
> +                       mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
> +                       ports {
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               port@0 {
> +                                       reg = <0>;
> +                                       panel0_in: endpoint {
> +                                               remote-endpoint = <&dsi0_out>;
> +                                       };
> +                               };
> +
> +                               port@1 {
> +                                       reg = <1>;
> +                                       panel1_in: endpoint {
> +                                               remote-endpoint = <&dsi1_out>;
> +                                       };
> +                               };
> +                       };
> +               };
> +       };
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings
  2018-10-04 19:01   ` Rob Herring
@ 2018-10-04 19:42     ` Abhinav Kumar
  2018-10-05 17:38       ` Abhinav Kumar
  0 siblings, 1 reply; 6+ messages in thread
From: Abhinav Kumar @ 2018-10-04 19:42 UTC (permalink / raw)
  To: Rob Herring
  Cc: Thierry Reding, linux-arm-msm, dri-devel, Sean Paul,
	Kristian H . Kristensen, chandanu

Hi Rob

Thanks for the review. Will copy the DT list in the next patchset.

Some comments inline.

Thanks

Abhinav

On 2018-10-04 12:01, Rob Herring wrote:
> If you want DT bindings reviewed, you have to cc the DT list. (Or wait
> for Sean Paul to ping me on IRC)
> 
> On Fri, Sep 28, 2018 at 7:39 PM Abhinav Kumar <abhinavk@codeaurora.org> 
> wrote:
>> 
>> Add the device tree bindings for Truly NT35597 panel driver. This 
>> panel
>> driver supports both single DSI and dual DSI.
> 
> By driver, you means drives panel timing signals or a Linux driver?
> The former is okay, the latter is not.
Yes, I mean it driver panel timing signals.
> 
>> 
>> However, this patch series supports only dual DSI.
>> 
>> Changes in v9:
>>   - None
>> 
>> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
>> Reviewed-by: Sean Paul <seanpaul@chromium.org>
>> Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
>> ---
>>  .../devicetree/bindings/display/truly,nt35597.txt  | 60 
>> ++++++++++++++++++++++
>>  1 file changed, 60 insertions(+)
>>  create mode 100644 
>> Documentation/devicetree/bindings/display/truly,nt35597.txt
>> 
>> diff --git 
>> a/Documentation/devicetree/bindings/display/truly,nt35597.txt 
>> b/Documentation/devicetree/bindings/display/truly,nt35597.txt
>> new file mode 100644
>> index 0000000..46b29eb
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/truly,nt35597.txt
>> @@ -0,0 +1,60 @@
>> +Truly model NT35597 DSI display driver
>> +
>> +The Truly NT35597 is a generic display driver, currently only 
>> configured
>> +for use in the 2K display on the Qualcomm SDM845.
> 
> So this is for *all* SDM845 based boards?
This is for SDM845 MTP board. Let me mention that as well.
> 
>> +
>> +Required properties:
>> +- compatible: should be "truly,nt35597-2K-display"
>> +- vdda-supply: phandle of the regulator that provides the supply 
>> voltage
>> +  Power IC supply
>> +- vdispp-supply: phandle of the regulator that provides the supply 
>> voltage
>> +  for positive LCD bias
>> +- vdispn-supply: phandle of the regulator that provides the supply 
>> voltage
>> +  for negative LCD bias
>> +- reset-gpios: phandle of gpio for reset line
>> +  This should be 8mA, gpio can be configured using mux, pinctrl, 
>> pinctrl-names
>> +  (active low)
>> +- mode-gpios: phandle of the gpio for choosing the mode of the 
>> display
>> +  for single DSI or Dual DSI
>> +  (active high)
> 
> active high doesn't really make sense for this.
Alright, will remove this.
> 
>> +  This should be low for dual DSI and high for single DSI mode
>> +- ports: This device has two video ports driven by two DSIs. Their 
>> connections
>> +  are modelled using the OF graph bindings specified in
> 
> modeled
> 
>> +  Documentation/devicetree/bindings/graph.txt.
>> +  - port@0: DSI input port driven by master DSI
>> +  - port@1: DSI input port driven by secondary DSI
>> +
>> +Example:
>> +
>> +       dsi@ae94000 {
>> +               panel@0 {
>> +                       compatible = "truly,nt35597-2K-display";
>> +                       reg = <0>;
>> +                       vdda-supply = <&pm8998_l14>;
>> +                       vdispp-supply = <&lab_regulator>;
>> +                       vdispn-supply = <&ibb_regulator>;
>> +                       pinctrl-names = "default", "suspend";
>> +                       pinctrl-0 = <&dpu_dsi_active>;
>> +                       pinctrl-1 = <&dpu_dsi_suspend>;
>> +
>> +                       reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
>> +                       mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
>> +                       ports {
>> +                               #address-cells = <1>;
>> +                               #size-cells = <0>;
>> +                               port@0 {
>> +                                       reg = <0>;
>> +                                       panel0_in: endpoint {
>> +                                               remote-endpoint = 
>> <&dsi0_out>;
>> +                                       };
>> +                               };
>> +
>> +                               port@1 {
>> +                                       reg = <1>;
>> +                                       panel1_in: endpoint {
>> +                                               remote-endpoint = 
>> <&dsi1_out>;
>> +                                       };
>> +                               };
>> +                       };
>> +               };
>> +       };
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora 
>> Forum,
>> a Linux Foundation Collaborative Project
>> 
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings
  2018-10-04 19:42     ` Abhinav Kumar
@ 2018-10-05 17:38       ` Abhinav Kumar
  2018-10-05 18:35         ` Rob Herring
  0 siblings, 1 reply; 6+ messages in thread
From: Abhinav Kumar @ 2018-10-05 17:38 UTC (permalink / raw)
  To: Rob Herring
  Cc: Thierry Reding, linux-arm-msm, dri-devel, Sean Paul,
	Kristian H . Kristensen, chandanu

Hi Rob

Had one question on below comment. Can you please help to clarify?

Thanks

Abhinav
On 2018-10-04 12:42, Abhinav Kumar wrote:
> Hi Rob
> 
> Thanks for the review. Will copy the DT list in the next patchset.
> 
> Some comments inline.
> 
> Thanks
> 
> Abhinav
> 
> On 2018-10-04 12:01, Rob Herring wrote:
>> If you want DT bindings reviewed, you have to cc the DT list. (Or wait
>> for Sean Paul to ping me on IRC)
>> 
>> On Fri, Sep 28, 2018 at 7:39 PM Abhinav Kumar 
>> <abhinavk@codeaurora.org> wrote:
>>> 
>>> Add the device tree bindings for Truly NT35597 panel driver. This 
>>> panel
>>> driver supports both single DSI and dual DSI.
>> 
>> By driver, you means drives panel timing signals or a Linux driver?
>> The former is okay, the latter is not.
> Yes, I mean it driver panel timing signals.
>> 
>>> 
>>> However, this patch series supports only dual DSI.
>>> 
>>> Changes in v9:
>>>   - None
>>> 
>>> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
>>> Reviewed-by: Sean Paul <seanpaul@chromium.org>
>>> Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
>>> ---
>>>  .../devicetree/bindings/display/truly,nt35597.txt  | 60 
>>> ++++++++++++++++++++++
>>>  1 file changed, 60 insertions(+)
>>>  create mode 100644 
>>> Documentation/devicetree/bindings/display/truly,nt35597.txt
>>> 
>>> diff --git 
>>> a/Documentation/devicetree/bindings/display/truly,nt35597.txt 
>>> b/Documentation/devicetree/bindings/display/truly,nt35597.txt
>>> new file mode 100644
>>> index 0000000..46b29eb
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/display/truly,nt35597.txt
>>> @@ -0,0 +1,60 @@
>>> +Truly model NT35597 DSI display driver
>>> +
>>> +The Truly NT35597 is a generic display driver, currently only 
>>> configured
>>> +for use in the 2K display on the Qualcomm SDM845.
>> 
>> So this is for *all* SDM845 based boards?
> This is for SDM845 MTP board. Let me mention that as well.
>> 
>>> +
>>> +Required properties:
>>> +- compatible: should be "truly,nt35597-2K-display"
>>> +- vdda-supply: phandle of the regulator that provides the supply 
>>> voltage
>>> +  Power IC supply
>>> +- vdispp-supply: phandle of the regulator that provides the supply 
>>> voltage
>>> +  for positive LCD bias
>>> +- vdispn-supply: phandle of the regulator that provides the supply 
>>> voltage
>>> +  for negative LCD bias
>>> +- reset-gpios: phandle of gpio for reset line
>>> +  This should be 8mA, gpio can be configured using mux, pinctrl, 
>>> pinctrl-names
>>> +  (active low)
>>> +- mode-gpios: phandle of the gpio for choosing the mode of the 
>>> display
>>> +  for single DSI or Dual DSI
>>> +  (active high)
>> 
>> active high doesn't really make sense for this.
> Alright, will remove this.
Here you would prefer us to make this GPIO active low right?
OR you were just mentioning that I can remove the active high 
documentation?
>> 
>>> +  This should be low for dual DSI and high for single DSI mode
>>> +- ports: This device has two video ports driven by two DSIs. Their 
>>> connections
>>> +  are modelled using the OF graph bindings specified in
>> 
>> modeled
>> 
>>> +  Documentation/devicetree/bindings/graph.txt.
>>> +  - port@0: DSI input port driven by master DSI
>>> +  - port@1: DSI input port driven by secondary DSI
>>> +
>>> +Example:
>>> +
>>> +       dsi@ae94000 {
>>> +               panel@0 {
>>> +                       compatible = "truly,nt35597-2K-display";
>>> +                       reg = <0>;
>>> +                       vdda-supply = <&pm8998_l14>;
>>> +                       vdispp-supply = <&lab_regulator>;
>>> +                       vdispn-supply = <&ibb_regulator>;
>>> +                       pinctrl-names = "default", "suspend";
>>> +                       pinctrl-0 = <&dpu_dsi_active>;
>>> +                       pinctrl-1 = <&dpu_dsi_suspend>;
>>> +
>>> +                       reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
>>> +                       mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
>>> +                       ports {
>>> +                               #address-cells = <1>;
>>> +                               #size-cells = <0>;
>>> +                               port@0 {
>>> +                                       reg = <0>;
>>> +                                       panel0_in: endpoint {
>>> +                                               remote-endpoint = 
>>> <&dsi0_out>;
>>> +                                       };
>>> +                               };
>>> +
>>> +                               port@1 {
>>> +                                       reg = <1>;
>>> +                                       panel1_in: endpoint {
>>> +                                               remote-endpoint = 
>>> <&dsi1_out>;
>>> +                                       };
>>> +                               };
>>> +                       };
>>> +               };
>>> +       };
>>> --
>>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora 
>>> Forum,
>>> a Linux Foundation Collaborative Project
>>> 
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings
  2018-10-05 17:38       ` Abhinav Kumar
@ 2018-10-05 18:35         ` Rob Herring
  0 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2018-10-05 18:35 UTC (permalink / raw)
  To: abhinavk
  Cc: Thierry Reding, linux-arm-msm, dri-devel, Sean Paul,
	Kristian H . Kristensen, chandanu

On Fri, Oct 5, 2018 at 12:38 PM Abhinav Kumar <abhinavk@codeaurora.org> wrote:
>
> Hi Rob
>
> Had one question on below comment. Can you please help to clarify?
>
> Thanks
>
> Abhinav
> On 2018-10-04 12:42, Abhinav Kumar wrote:
> > Hi Rob
> >
> > Thanks for the review. Will copy the DT list in the next patchset.
> >
> > Some comments inline.
> >
> > Thanks
> >
> > Abhinav
> >
> > On 2018-10-04 12:01, Rob Herring wrote:
> >> If you want DT bindings reviewed, you have to cc the DT list. (Or wait
> >> for Sean Paul to ping me on IRC)
> >>
> >> On Fri, Sep 28, 2018 at 7:39 PM Abhinav Kumar

[...]

> >>> +- reset-gpios: phandle of gpio for reset line
> >>> +  This should be 8mA, gpio can be configured using mux, pinctrl,
> >>> pinctrl-names
> >>> +  (active low)
> >>> +- mode-gpios: phandle of the gpio for choosing the mode of the
> >>> display
> >>> +  for single DSI or Dual DSI
> >>> +  (active high)
> >>
> >> active high doesn't really make sense for this.
> > Alright, will remove this.
> Here you would prefer us to make this GPIO active low right?

No, because both states are active.

> OR you were just mentioning that I can remove the active high
> documentation?

Correct.

Rob
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2018-10-05 18:35 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-09-29  0:38 [PATCH v9 1/2] drm/panel: Add support for Truly NT35597 panel driver Abhinav Kumar
2018-09-29  0:38 ` [PATCH v9 2/2] dt-bindings: Add Truly NT35597 panel driver bindings Abhinav Kumar
2018-10-04 19:01   ` Rob Herring
2018-10-04 19:42     ` Abhinav Kumar
2018-10-05 17:38       ` Abhinav Kumar
2018-10-05 18:35         ` Rob Herring

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.