Re: [PATCH 6/6] riscv: dts: starfive: Add crypto and DMA node for VisionFive 2

From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Jia Jie Ho <jiajie.ho@starfivetech.com>,
	Herbert Xu <herbert@gondor.apana.org.au>,
	"David S . Miller" <davem@davemloft.net>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-crypto@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-riscv@lists.infradead.org
Subject: Re: [PATCH 6/6] riscv: dts: starfive: Add crypto and DMA node for VisionFive 2
Date: Wed, 30 Nov 2022 14:21:36 +0100	[thread overview]
Message-ID: <6de013d9-f2ab-a2d8-1022-2474c037c737@linaro.org> (raw)
In-Reply-To: <20221130055214.2416888-7-jiajie.ho@starfivetech.com>

On 30/11/2022 06:52, Jia Jie Ho wrote:
> Adding StarFive crypto IP and DMA controller node
> to VisionFive 2 SoC.
> 
> Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
> Signed-off-by: Huan Feng <huan.feng@starfivetech.com>
> ---
>  .../jh7110-starfive-visionfive-v2.dts         |  8 +++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 36 +++++++++++++++++++
>  2 files changed, 44 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
> index 450e920236a5..da2aa4d597f3 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
> @@ -115,3 +115,11 @@ &tdm_ext {
>  &mclk_ext {
>  	clock-frequency = <49152000>;
>  };
> +
> +&sec_dma {
> +	status = "okay";
> +};
> +
> +&crypto {
> +	status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 4ac159d79d66..745a5650882c 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -455,5 +455,41 @@ uart5: serial@12020000 {
>  			reg-shift = <2>;
>  			status = "disabled";
>  		};
> +
> +		sec_dma: sec_dma@16008000 {

Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

No underscores in node names.

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

Best regards,
Krzysztof