* [U-Boot] [PATCH] Support for the OpenRD base board
@ 2009-09-10 13:02 Simon Kagstrom
2009-09-11 8:14 ` [U-Boot] [PATCH v2] " Simon Kagstrom
` (2 more replies)
0 siblings, 3 replies; 12+ messages in thread
From: Simon Kagstrom @ 2009-09-10 13:02 UTC (permalink / raw)
To: u-boot
Support for the OpenRD base board
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code and likely to be a bit incomplete.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
---
The configuration does not include UBIFS support, which still needs
he remaining patches for the bitops cleanup and fixes:
http://lists.denx.de/pipermail/u-boot/2009-August/059285.html
to build. Until those are applied, it's turned off here.
I get run-time problems when building for armv5te for OpenRD base
(apparently the same problem occurs for other Kirkwood boards). This
patch fixes that:
http://lists.denx.de/pipermail/u-boot/2009-September/059896.html
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/openrd_base/Makefile | 51 +++++++
board/Marvell/openrd_base/config.mk | 25 ++++
board/Marvell/openrd_base/openrd_base.c | 158 ++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.h | 46 +++++++
include/configs/openrd_base.h | 218 +++++++++++++++++++++++++++++++
8 files changed, 506 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/openrd_base/Makefile
create mode 100644 board/Marvell/openrd_base/config.mk
create mode 100644 board/Marvell/openrd_base/openrd_base.c
create mode 100644 board/Marvell/openrd_base/openrd_base.h
create mode 100644 include/configs/openrd_base.h
diff --git a/MAINTAINERS b/MAINTAINERS
index e9db278..99cdc12 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -588,6 +588,10 @@ Gary Jennejohn <garyj@denx.de>
Konstantin Kletschke <kletschke@synertronixx.de>
scb9328 ARM920T
+Simon Kagstrom <simon.kagstrom@netinsight.net>
+
+ openrd_base ARM926EJS (Kirkwood SoC)
+
Nishant Kamat <nskamat@ti.com>
omap1610h2 ARM926EJS
diff --git a/MAKEALL b/MAKEALL
index f0ed8ea..9e6eee2 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -533,6 +533,7 @@ LIST_ARM9=" \
omap1610inn \
omap5912osk \
omap730p2 \
+ openrd_base \
rd6281a \
sbc2410x \
scb9328 \
diff --git a/Makefile b/Makefile
index 0449a5b..27b0179 100644
--- a/Makefile
+++ b/Makefile
@@ -3018,6 +3018,9 @@ omap1610h2_cs_autoboot_config: unconfig
omap5912osk_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
+openrd_base_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
omap730p2_config \
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
new file mode 100644
index 0000000..defbb08
--- /dev/null
+++ b/board/Marvell/openrd_base/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := openrd_base.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd_base/config.mk b/board/Marvell/openrd_base/config.mk
new file mode 100644
index 0000000..a4ea769
--- /dev/null
+++ b/board/Marvell/openrd_base/config.mk
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
new file mode 100644
index 0000000..4c9a848
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.c
@@ -0,0 +1,158 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd_base.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(OPENRD_OE_VAL_LOW,
+ OPENRD_OE_VAL_HIGH,
+ OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD, /* Alt UART1_TXD */
+ MPP14_SD_D0, /* Alt UART1_RXD */
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO, /* UART1 / SD sel */
+ MPP35_TDM_CH0_TX_QL,
+ MPP36_TDM_SPI_CS1,
+ MPP37_TDM_CH2_TX_QL,
+ MPP38_TDM_CH2_RX_QL,
+ MPP39_AUDIO_I2SBCLK,
+ MPP40_AUDIO_I2SDO,
+ MPP41_AUDIO_I2SLRC,
+ MPP42_AUDIO_I2SMCLK,
+ MPP43_AUDIO_I2SDI,
+ MPP44_AUDIO_EXTCLK,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_TDM_CH0_RX_QL,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
new file mode 100644
index 0000000..f3daf17
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.h
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_BASE_H
+#define __OPENRD_BASE_H
+
+#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
+#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __OPENRD_BASE_H */
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
new file mode 100644
index 0000000..ebda0c5
--- /dev/null
+++ b/include/configs/openrd_base.h
@@ -0,0 +1,218 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_BASE_H
+#define _CONFIG_OPENRD_BASE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-OpenRD_base"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_BASE /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_MV88E1116 /* Support for the MV88E1116 PHY */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_IMI
+/*
+ * Flash configuration
+ */
+#ifndef CONFIG_CMD_FLASH
+#define CONFIG_SYS_NO_FLASH 1 /* Declare no flash (NOR/SPI) */
+#endif
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0xa0000
+#define CONFIG_ENV_OFFSET 0xa0000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x8
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_OPENRD_BASE_H */
--
1.6.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2] Support for the OpenRD base board
2009-09-10 13:02 [U-Boot] [PATCH] Support for the OpenRD base board Simon Kagstrom
@ 2009-09-11 8:14 ` Simon Kagstrom
2009-09-11 10:43 ` Prafulla Wadaskar
2009-09-14 7:46 ` [U-Boot] [PATCH v3] " Simon Kagstrom
2009-09-21 10:54 ` [U-Boot] [PATCH v4] " Simon Kagstrom
2 siblings, 1 reply; 12+ messages in thread
From: Simon Kagstrom @ 2009-09-11 8:14 UTC (permalink / raw)
To: u-boot
Support for the OpenRD base board
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code and likely to be a bit incomplete.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
---
The configuration does not include UBIFS support, which still needs
he remaining patches for the bitops cleanup and fixes:
http://lists.denx.de/pipermail/u-boot/2009-August/059285.html
to build. Until those are applied, it's turned off here.
I get run-time problems when building for armv5te for OpenRD base
(apparently the same problem occurs for other Kirkwood boards). This
patch fixes that:
http://lists.denx.de/pipermail/u-boot/2009-September/059896.html
The second version contains the kwbimage.cfg needed to produce an image
to install on the NAND flash.
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/openrd_base/Makefile | 51 +++++++
board/Marvell/openrd_base/config.mk | 28 ++++
board/Marvell/openrd_base/kwbimage.cfg | 168 ++++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.c | 158 ++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.h | 46 +++++++
include/configs/openrd_base.h | 218 +++++++++++++++++++++++++++++++
9 files changed, 677 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/openrd_base/Makefile
create mode 100644 board/Marvell/openrd_base/config.mk
create mode 100644 board/Marvell/openrd_base/kwbimage.cfg
create mode 100644 board/Marvell/openrd_base/openrd_base.c
create mode 100644 board/Marvell/openrd_base/openrd_base.h
create mode 100644 include/configs/openrd_base.h
diff --git a/MAINTAINERS b/MAINTAINERS
index e9db278..99cdc12 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -588,6 +588,10 @@ Gary Jennejohn <garyj@denx.de>
Konstantin Kletschke <kletschke@synertronixx.de>
scb9328 ARM920T
+Simon Kagstrom <simon.kagstrom@netinsight.net>
+
+ openrd_base ARM926EJS (Kirkwood SoC)
+
Nishant Kamat <nskamat@ti.com>
omap1610h2 ARM926EJS
diff --git a/MAKEALL b/MAKEALL
index f0ed8ea..9e6eee2 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -533,6 +533,7 @@ LIST_ARM9=" \
omap1610inn \
omap5912osk \
omap730p2 \
+ openrd_base \
rd6281a \
sbc2410x \
scb9328 \
diff --git a/Makefile b/Makefile
index 9764cea..6cef82a 100644
--- a/Makefile
+++ b/Makefile
@@ -3022,6 +3022,9 @@ omap1610h2_cs_autoboot_config: unconfig
omap5912osk_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
+openrd_base_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
omap730p2_config \
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
new file mode 100644
index 0000000..defbb08
--- /dev/null
+++ b/board/Marvell/openrd_base/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := openrd_base.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd_base/config.mk b/board/Marvell/openrd_base/config.mk
new file mode 100644
index 0000000..2bd9f79
--- /dev/null
+++ b/board/Marvell/openrd_base/config.mk
@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg
new file mode 100644
index 0000000..1228ac8
--- /dev/null
+++ b/board/Marvell/openrd_base/kwbimage.cfg
@@ -0,0 +1,168 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Reserved
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Reserved
+# bit7-6: 11, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000042 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 1, DDR drive strength reduced
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
+# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
+# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
+# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+
+DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
+# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
+# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
+# bit14: 1, M_STARTBURST_IN ODT: Enabled
+# bit15: 1, DDR IO ODT Unit: Use ODT block
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
new file mode 100644
index 0000000..4c9a848
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.c
@@ -0,0 +1,158 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd_base.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(OPENRD_OE_VAL_LOW,
+ OPENRD_OE_VAL_HIGH,
+ OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD, /* Alt UART1_TXD */
+ MPP14_SD_D0, /* Alt UART1_RXD */
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO, /* UART1 / SD sel */
+ MPP35_TDM_CH0_TX_QL,
+ MPP36_TDM_SPI_CS1,
+ MPP37_TDM_CH2_TX_QL,
+ MPP38_TDM_CH2_RX_QL,
+ MPP39_AUDIO_I2SBCLK,
+ MPP40_AUDIO_I2SDO,
+ MPP41_AUDIO_I2SLRC,
+ MPP42_AUDIO_I2SMCLK,
+ MPP43_AUDIO_I2SDI,
+ MPP44_AUDIO_EXTCLK,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_TDM_CH0_RX_QL,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
new file mode 100644
index 0000000..f3daf17
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.h
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_BASE_H
+#define __OPENRD_BASE_H
+
+#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
+#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __OPENRD_BASE_H */
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
new file mode 100644
index 0000000..ebda0c5
--- /dev/null
+++ b/include/configs/openrd_base.h
@@ -0,0 +1,218 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_BASE_H
+#define _CONFIG_OPENRD_BASE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-OpenRD_base"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_BASE /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_MV88E1116 /* Support for the MV88E1116 PHY */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_IMI
+/*
+ * Flash configuration
+ */
+#ifndef CONFIG_CMD_FLASH
+#define CONFIG_SYS_NO_FLASH 1 /* Declare no flash (NOR/SPI) */
+#endif
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0xa0000
+#define CONFIG_ENV_OFFSET 0xa0000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x8
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_OPENRD_BASE_H */
--
1.6.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2] Support for the OpenRD base board
2009-09-11 8:14 ` [U-Boot] [PATCH v2] " Simon Kagstrom
@ 2009-09-11 10:43 ` Prafulla Wadaskar
2009-09-11 12:18 ` Simon Kagstrom
0 siblings, 1 reply; 12+ messages in thread
From: Prafulla Wadaskar @ 2009-09-11 10:43 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Simon Kagstrom [mailto:simon.kagstrom at netinsight.net]
> Sent: Friday, September 11, 2009 1:45 PM
> To: U-Boot ML
> Cc: Prafulla Wadaskar; Dhaval Vasa; Prabhanjan Sarnaik; Ashish Karkare
> Subject: [PATCH v2] Support for the OpenRD base board
>
> Support for the OpenRD base board
>
> The implementation is borrowed from the sheevaplug board and
> the Marvell
> 1.1.4 code and likely to be a bit incomplete.
>
> Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
> ---
> The configuration does not include UBIFS support, which still needs
> he remaining patches for the bitops cleanup and fixes:
Pls correct typo here
>
> http://lists.denx.de/pipermail/u-boot/2009-August/059285.html
>
> to build. Until those are applied, it's turned off here.
>
>
> I get run-time problems when building for armv5te for OpenRD base
> (apparently the same problem occurs for other Kirkwood boards). This
> patch fixes that:
>
> http://lists.denx.de/pipermail/u-boot/2009-September/059896.html
>
>
> The second version contains the kwbimage.cfg needed to
> produce an image
> to install on the NAND flash.
>
> MAINTAINERS | 4 +
> MAKEALL | 1 +
> Makefile | 3 +
> board/Marvell/openrd_base/Makefile | 51 +++++++
> board/Marvell/openrd_base/config.mk | 28 ++++
> board/Marvell/openrd_base/kwbimage.cfg | 168
> ++++++++++++++++++++++++
> board/Marvell/openrd_base/openrd_base.c | 158 ++++++++++++++++++++++
> board/Marvell/openrd_base/openrd_base.h | 46 +++++++
> include/configs/openrd_base.h | 218
> +++++++++++++++++++++++++++++++
> 9 files changed, 677 insertions(+), 0 deletions(-)
> create mode 100644 board/Marvell/openrd_base/Makefile
> create mode 100644 board/Marvell/openrd_base/config.mk
> create mode 100644 board/Marvell/openrd_base/kwbimage.cfg
> create mode 100644 board/Marvell/openrd_base/openrd_base.c
> create mode 100644 board/Marvell/openrd_base/openrd_base.h
> create mode 100644 include/configs/openrd_base.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index e9db278..99cdc12 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -588,6 +588,10 @@ Gary Jennejohn <garyj@denx.de>
> Konstantin Kletschke <kletschke@synertronixx.de>
> scb9328 ARM920T
>
> +Simon Kagstrom <simon.kagstrom@netinsight.net>
> +
> + openrd_base ARM926EJS (Kirkwood SoC)
> +
> Nishant Kamat <nskamat@ti.com>
>
> omap1610h2 ARM926EJS
> diff --git a/MAKEALL b/MAKEALL
> index f0ed8ea..9e6eee2 100755
> --- a/MAKEALL
> +++ b/MAKEALL
> @@ -533,6 +533,7 @@ LIST_ARM9=" \
> omap1610inn \
> omap5912osk \
> omap730p2 \
> + openrd_base \
> rd6281a \
> sbc2410x \
> scb9328 \
> diff --git a/Makefile b/Makefile
> index 9764cea..6cef82a 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -3022,6 +3022,9 @@ omap1610h2_cs_autoboot_config: unconfig
> omap5912osk_config : unconfig
> @$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
>
> +openrd_base_config: unconfig
> + @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=)
> Marvell kirkwood
> +
> xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,,
> $(subst _config,,$1)))
>
> omap730p2_config \
> diff --git a/board/Marvell/openrd_base/Makefile
> b/board/Marvell/openrd_base/Makefile
> new file mode 100644
> index 0000000..defbb08
> --- /dev/null
> +++ b/board/Marvell/openrd_base/Makefile
> @@ -0,0 +1,51 @@
> +#
> +# (C) Copyright 2009
> +# Marvell Semiconductor <www.marvell.com>
> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
I think you must add your reference here..
>
+#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> +# MA 02110-1301 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB = $(obj)lib$(BOARD).a
> +
> +COBJS := openrd_base.o
> +
> +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS))
> +SOBJS := $(addprefix $(obj),$(SOBJS))
> +
> +$(LIB): $(obj).depend $(OBJS) $(SOBJS)
> + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
> +
> +clean:
> + rm -f $(SOBJS) $(OBJS)
> +
> +distclean: clean
> + rm -f $(LIB) core *.bak .depend
> +
> +#############################################################
> ############
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#############################################################
> ############
> diff --git a/board/Marvell/openrd_base/config.mk
> b/board/Marvell/openrd_base/config.mk
> new file mode 100644
> index 0000000..2bd9f79
> --- /dev/null
> +++ b/board/Marvell/openrd_base/config.mk
> @@ -0,0 +1,28 @@
> +#
> +# (C) Copyright 2009
> +# Marvell Semiconductor <www.marvell.com>
> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
Same here
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> +# MA 02110-1301 USA
> +#
> +
> +TEXT_BASE = 0x00600000
> +
> +# Kirkwood Boot Image configuration file
> +KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
> diff --git a/board/Marvell/openrd_base/kwbimage.cfg
> b/board/Marvell/openrd_base/kwbimage.cfg
> new file mode 100644
> index 0000000..1228ac8
> --- /dev/null
> +++ b/board/Marvell/openrd_base/kwbimage.cfg
> @@ -0,0 +1,168 @@
> +#
> +# (C) Copyright 2009
> +# Marvell Semiconductor <www.marvell.com>
> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> +# MA 02110-1301 USA
> +#
> +# Refer docs/README.kwimage for more details about how-to configure
> +# and create kirkwood boot image
> +#
> +
> +# Boot Media configurations
> +BOOT_FROM nand
> +NAND_ECC_MODE default
> +NAND_PAGE_SIZE 0x0800
> +
> +# SOC registers configuration using bootrom header extension
> +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> +
> +# Configure RGMII-0 interface pad voltage to 1.8V
> +DATA 0xFFD100e0 0x1b1b1b9b
> +
> +#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> +DATA 0xFFD01400 0x43000c30 # DDR Configuration register
> +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
> +# bit23-14: zero
> +# bit24: 1= enable exit self refresh mode on DDR access
> +# bit25: 1 required
> +# bit29-26: zero
> +# bit31-30: 01
> +
> +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
> +# bit 4: 0=addr/cmd in smame cycle
> +# bit 5: 0=clk is driven during self refresh, we don't
> care for APX
> +# bit 6: 0=use recommended falling edge of clk for addr/cmd
> +# bit14: 0=input buffer always powered up
> +# bit18: 1=cpu lock transaction enabled
> +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL
> disabled bit31=0
> +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs
> 400MHz, unbuffered DIMM
> +# bit30-28: 3 required
> +# bit31: 0=no additional STARTBURST delay
> +
> +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active
> cycles value +1)
> +# bit3-0: TRAS lsbs
> +# bit7-4: TRCD
> +# bit11- 8: TRP
> +# bit15-12: TWR
> +# bit19-16: TWTR
> +# bit20: TRAS msb
> +# bit23-21: 0x0
> +# bit27-24: TRRD
> +# bit31-28: TRTP
> +
> +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
> +# bit6-0: TRFC
> +# bit8-7: TR2R
> +# bit10-9: TR2W
> +# bit12-11: TW2W
> +# bit31-13: zero required
> +
> +DATA 0xFFD01410 0x000000cc # DDR Address Control
> +# bit1-0: 00, Reserved
This means 0x8 not reserved as per rev-C specification document
> +# bit3-2: 11, Cs0size=1Gb
> +# bit5-4: 00, Reserved
Ditto
> +# bit7-6: 11, Cs1size=1Gb
> +# bit9-8: 00, Cs2width=nonexistent
> +# bit11-10: 00, Cs2size =nonexistent
> +# bit13-12: 00, Cs3width=nonexistent
> +# bit15-14: 00, Cs3size =nonexistent
> +# bit16: 0, Cs0AddrSel
> +# bit17: 0, Cs1AddrSel
> +# bit18: 0, Cs2AddrSel
> +# bit19: 0, Cs3AddrSel
> +# bit31-20: 0 required
> +
> +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> +# bit0: 0, OpenPage enabled
> +# bit31-1: 0 required
> +
> +DATA 0xFFD01418 0x00000000 # DDR Operation
> +# bit3-0: 0x0, DDR cmd
> +# bit31-4: 0 required
> +
> +DATA 0xFFD0141C 0x00000C52 # DDR Mode
> +# bit2-0: 2, BurstLen=2 required
> +# bit3: 0, BurstType=0 required
> +# bit6-4: 4, CL=5
> +# bit7: 0, TestMode=0 normal
> +# bit8: 0, DLL reset=0 normal
> +# bit11-9: 6, auto-precharge write recovery ????????????
> +# bit12: 0, PD must be zero
> +# bit31-13: 0 required
> +
> +DATA 0xFFD01420 0x00000042 # DDR Extended Mode
> +# bit0: 0, DDR DLL enabled
> +# bit1: 1, DDR drive strength reduced
> +# bit2: 0, DDR ODT control lsd (disabled)
> +# bit5-3: 000, required
> +# bit6: 1, DDR ODT control msb, (disabled)
> +# bit9-7: 000, required
> +# bit10: 0, differential DQS enabled
> +# bit11: 0, required
> +# bit12: 0, DDR output buffer enabled
> +# bit31-13: 0 required
> +
> +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
> +# bit2-0: 111, required
> +# bit3 : 1 , MBUS Burst Chop disabled
> +# bit6-4: 111, required
> +# bit7 : 0
> +# bit8 : 1 , add writepath sample stage, must be 1 for
> DDR freq >= 300MHz
> +# bit9 : 0 , no half clock cycle addition to dataout
> +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> +# bit15-12: 1111 required
> +# bit31-16: 0 required
> +
> +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
> +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
> +
> +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
> +# bit0: 1, Window enabled
> +# bit1: 0, Write Protect disabled
> +# bit3-2: 00, CS0 hit selected
> +# bit23-4: ones, required
> +# bit31-24: 0x0F, Size (i.e. 256MB)
> +
> +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
> +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window
> enabled for CS1
> +
> +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> +
> +DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
> +# bit3-0: 0010, (read) M_ODT[0] is asserted during read
> from DRAM CS1
> +# bit7-4: 0001, (read) M_ODT[1] is asserted during read
> from DRAM CS0
> +# bit19-16: 0010, (write) M_ODT[0] is asserted during write
> to DRAM CS1.
> +# bit23-20: 0001, (write) M_ODT[1] is asserted during write
> to DRAM CS0.
> +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> +
> +DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
> +# bit3-0: 1111, internal ODT is asserted during read from
> DRAM bank 0-3
> +# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT
> Select: 150 ohm
> +# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
> +# bit14: 1, M_STARTBURST_IN ODT: Enabled
> +# bit15: 1, DDR IO ODT Unit: Use ODT block
> +DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> +#bit0=1, enable DDR init upon this register write
> +
> +# End of Header extension
> +DATA 0x0 0x0
> diff --git a/board/Marvell/openrd_base/openrd_base.c
> b/board/Marvell/openrd_base/openrd_base.c
> new file mode 100644
> index 0000000..4c9a848
> --- /dev/null
> +++ b/board/Marvell/openrd_base/openrd_base.c
> @@ -0,0 +1,158 @@
> +/*
> + * (C) Copyright 2009
> + * Net Insight <www.netinsight.net>
> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
> + *
> + * Based on sheevaplug.c:
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
You can follow the same documentation for above files
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#include <common.h>
> +#include <miiphy.h>
> +#include <asm/arch/kirkwood.h>
> +#include <asm/arch/mpp.h>
> +#include "openrd_base.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int board_init(void)
> +{
> + /*
> + * default gpio configuration
> + * There are maximum 64 gpios controlled through 2 sets
> of registers
> + * the below configuration configures mainly initial LED status
> + */
> + kw_config_gpio(OPENRD_OE_VAL_LOW,
> + OPENRD_OE_VAL_HIGH,
> + OPENRD_OE_LOW, OPENRD_OE_HIGH);
> +
> + /* Multi-Purpose Pins Functionality configuration */
> + u32 kwmpp_config[] = {
> + MPP0_NF_IO2,
> + MPP1_NF_IO3,
> + MPP2_NF_IO4,
> + MPP3_NF_IO5,
> + MPP4_NF_IO6,
> + MPP5_NF_IO7,
> + MPP6_SYSRST_OUTn,
> + MPP7_GPO,
> + MPP8_TW_SDA,
> + MPP9_TW_SCK,
> + MPP10_UART0_TXD,
> + MPP11_UART0_RXD,
> + MPP12_SD_CLK,
> + MPP13_SD_CMD, /* Alt UART1_TXD */
> + MPP14_SD_D0, /* Alt UART1_RXD */
> + MPP15_SD_D1,
> + MPP16_SD_D2,
> + MPP17_SD_D3,
> + MPP18_NF_IO0,
> + MPP19_NF_IO1,
> + MPP20_GE1_0,
> + MPP21_GE1_1,
> + MPP22_GE1_2,
> + MPP23_GE1_3,
> + MPP24_GE1_4,
> + MPP25_GE1_5,
> + MPP26_GE1_6,
> + MPP27_GE1_7,
> + MPP28_GPIO,
> + MPP29_TSMP9,
> + MPP30_GE1_10,
> + MPP31_GE1_11,
> + MPP32_GE1_12,
> + MPP33_GE1_13,
> + MPP34_GPIO, /* UART1 / SD sel */
> + MPP35_TDM_CH0_TX_QL,
> + MPP36_TDM_SPI_CS1,
> + MPP37_TDM_CH2_TX_QL,
> + MPP38_TDM_CH2_RX_QL,
> + MPP39_AUDIO_I2SBCLK,
> + MPP40_AUDIO_I2SDO,
> + MPP41_AUDIO_I2SLRC,
> + MPP42_AUDIO_I2SMCLK,
> + MPP43_AUDIO_I2SDI,
> + MPP44_AUDIO_EXTCLK,
> + MPP45_TDM_PCLK,
> + MPP46_TDM_FS,
> + MPP47_TDM_DRX,
> + MPP48_TDM_DTX,
> + MPP49_TDM_CH0_RX_QL,
> + 0
> + };
Looks better if empty line can be inserted here
> + kirkwood_mpp_conf(kwmpp_config);
> +
> + /*
> + * arch number of board
> + */
> + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
> +
> + /* adress of boot parameters */
> + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
> + return 0;
Pls correct indentation b y using tabs only here and everywhere
> +}
> +
> +int dram_init(void)
> +{
> + int i;
> +
> + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
> + gd->bd->bi_dram[i].start = kw_sdram_bar(i);
> + gd->bd->bi_dram[i].size = kw_sdram_bs(i);
> + }
> + return 0;
> +}
> +
> +#ifdef CONFIG_RESET_PHY_R
> +void reset_phy(void)
> +{
> + u16 reg;
> + u16 devadr;
> + char *name = "egiga0";
> +
> + if (miiphy_set_current_dev(name))
> + return;
> +
> + /* command to read PHY dev address */
> + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
> + printf("Err..%s could not read PHY dev address\n",
> + __FUNCTION__);
> + return;
> + }
> +
> + /*
> + * Enable RGMII delay on Tx and Rx for CPU port
> + * Ref: sec 4.7.2 of chip datasheet
> + */
> + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
> + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
> + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
> + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
> + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
> +
> + /* reset the phy */
> + miiphy_reset(name, devadr);
> +
> + printf("88E1116 Initialized on %s\n", name);
> +}
> +#endif /* CONFIG_RESET_PHY_R */
> diff --git a/board/Marvell/openrd_base/openrd_base.h
> b/board/Marvell/openrd_base/openrd_base.h
> new file mode 100644
> index 0000000..f3daf17
> --- /dev/null
> +++ b/board/Marvell/openrd_base/openrd_base.h
> @@ -0,0 +1,46 @@
> +/*
> + * (C) Copyright 2009
> + * Net Insight <www.netinsight.net>
> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
> + *
> + * Based on sheevaplug.h:
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#ifndef __OPENRD_BASE_H
> +#define __OPENRD_BASE_H
> +
> +#define OPENRD_OE_LOW (~(1<<28)) /*
> RS232 / RS485 */
> +#define OPENRD_OE_HIGH (~(1<<2)) /* SD
> / UART1 */
> +#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
> +#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
> +
> +/* PHY related */
> +#define MV88E1116_LED_FCTRL_REG 10
> +#define MV88E1116_CPRSP_CR3_REG 21
> +#define MV88E1116_MAC_CTRL_REG 21
> +#define MV88E1116_PGADR_REG 22
> +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
> +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
> +
> +#endif /* __OPENRD_BASE_H */
> diff --git a/include/configs/openrd_base.h
> b/include/configs/openrd_base.h
> new file mode 100644
> index 0000000..ebda0c5
> --- /dev/null
> +++ b/include/configs/openrd_base.h
> @@ -0,0 +1,218 @@
> +/*
> + * (C) Copyright 2009
> + * Net Insight <www.netinsight.net>
> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
> + *
> + * Based on sheevaplug.h:
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#ifndef _CONFIG_OPENRD_BASE_H
> +#define _CONFIG_OPENRD_BASE_H
> +
> +/*
> + * Version number information
> + */
> +#define CONFIG_IDENT_STRING "\nMarvell-OpenRD_base"
Is this name in synce with what you have registered on armlinux with machin-id?
Can you pls use short name here?
> +
> +/*
> + * High Level Configuration Options (easy to change)
> + */
> +#define CONFIG_MARVELL 1
> +#define CONFIG_ARM926EJS 1 /* Basic Architecture */
> +#define CONFIG_FEROCEON_88FR131 1 /* CPU Core
> subversion */
Pls Use CONFIG_SHEEVA_88SV131 here
> +#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
> +#define CONFIG_KW88F6281 1 /* SOC Name */
> +#define CONFIG_MACH_OPENRD_BASE /* Machine type */
> +
> +#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5
> support */
> +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board
> lowlevel_init */
> +#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1
> for kernel */
> +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII
> Pad voltage to 1.8V */
Does this board have PCI interface, if yet then pls include following line
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
> +#define CONFIG_MV88E1116 /* Support for the
> MV88E1116 PHY */
> +
> +/*
> + * CLKs configurations
> + */
> +#define CONFIG_SYS_HZ 1000
> +
> +/*
> + * NS16550 Configuration
> + */
> +#define CONFIG_SYS_NS16550
> +#define CONFIG_SYS_NS16550_SERIAL
> +#define CONFIG_SYS_NS16550_REG_SIZE (-4)
> +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
> +#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
> +
> +/*
> + * Serial Port configuration
> + * The following definitions let you select what serial you
> want to use
> + * for your console driver.
> + */
> +
> +#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
> +#define CONFIG_BAUDRATE 115200
> +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
> + 115200,230400,
> 460800, 921600 }
> +/* auto boot */
> +#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
> +
> +/*
> + * For booting Linux, the board info and command line data
> + * have to be in the first 8 MB of memory, since this is
> + * the maximum mapped by the Linux kernel during initialization.
> + */
> +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
> +#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
> +#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
> +
> +#define CONFIG_SYS_PROMPT "Marvell>> " /*
> Command Prompt */
> +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O
> Buff Size */
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
> + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
> +/*
> + * Commands configuration
> + */
> +#define CONFIG_CMD_AUTOSCRIPT
> +#define CONFIG_CMD_BOOTD
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_ENV
> +#define CONFIG_CMD_FAT
> +#define CONFIG_CMD_LOADB
> +#define CONFIG_CMD_MEMORY
> +#define CONFIG_CMD_NAND
> +#define CONFIG_CMD_NET
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_RUN
> +#define CONFIG_CMD_SAVEENV
> +#define CONFIG_CMD_USB
> +#define CONFIG_CMD_IMI
Again I suggest to use config_cmd_default.h here :-) to bring it in sync with other Marvell and arm boards configuration
> +/*
> + * Flash configuration
> + */
> +#ifndef CONFIG_CMD_FLASH
> +#define CONFIG_SYS_NO_FLASH 1 /* Declare no
> flash (NOR/SPI) */
> +#endif
> +
> +/*
> + * NAND configuration
> + */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_NAND_KIRKWOOD
> +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> +#define NAND_MAX_CHIPS 1
> +#define CONFIG_SYS_NAND_BASE 0xD8000000 /*
> KW_DEFADR_NANDF */
> +#define NAND_ALLOW_ERASE_ALL 1
> +#endif
> +
> +/*
> + * Environment variables configurations
> + */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_ENV_IS_IN_NAND 1
> +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
> +#else
> +#define CONFIG_ENV_IS_NOWHERE 1 /* if
> env in SDRAM */
> +#endif
> +/*
> + * max 4k env size is enough, but in case of nand
> + * it has to be rounded to sector size
> + */
> +#define CONFIG_ENV_SIZE 0x20000 /* 128k */
> +#define CONFIG_ENV_ADDR 0xa0000
> +#define CONFIG_ENV_OFFSET 0xa0000 /* env starts here */
Do you really need this address? the u-boot binary is within 256kb, at the most it can go till 512kb
> +
> +/*
> + * Default environment variables
> + */
> +#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
> + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
> + "${x_bootcmd_usb}; bootm 0x6400000;"
> +
> +#define MTDIDS_DEFAULT "nand0=nand_mtd"
> +#define MTDPARTS_DEFAULT
> "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(
> uImage),"\
> + "0x1fb00000 at 0x500000(rootfs)"
This is must be the default setup in board setup file for openrd_base (if it is again derived from sheevaplug)
In that case this settings not required
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
> + "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
> + "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
> + "x_bootcmd_usb=usb start\0" \
You must add x_bootcmd_eth for program MAC addrss in hardware before kernel boot.
> + "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
> + "mtdids="MTDIDS_DEFAULT"\0" \
> + "mtdparts="MTDPARTS_DEFAULT"\0"
> +
> +/*
> + * Size of malloc() pool
> + */
> +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB
> for malloc() */
> +/* size in bytes reserved for initial data */
> +#define CONFIG_SYS_GBL_DATA_SIZE 128
> +
> +/*
> + * Other required minimal configurations
> + */
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_AUTO_COMPLETE
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
> +#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
> +#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
> +#define CONFIG_NR_DRAM_BANKS 4
> +#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
> +#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load
> adr- 8M */
> +#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
> +#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
> +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
> +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
> +
> +/*
> + * Ethernet Driver configuration
> + */
> +#ifdef CONFIG_CMD_NET
> +#define CONFIG_NETCONSOLE /* include NetConsole support */
> +#define CONFIG_NET_MULTI /* specify more that one ports
> available */
> +#define CONFIG_MII /* expose smi ove
> miiphy interface */
> +#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe
> Controller Driver */
> +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link
> using phy */
> +#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
> +#define CONFIG_PHY_BASE_ADR 0x8
> +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
> +#define CONFIG_RESET_PHY_R /* use reset_phy() to init
> mv8831116 PHY */
> +#endif /* CONFIG_CMD_NET */
> +
> +/*
> + * USB/EHCI
> + */
> +#ifdef CONFIG_CMD_USB
> +#define CONFIG_USB_EHCI /* Enable EHCI
> USB support */
> +#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
> +#define CONFIG_EHCI_IS_TDI
> +#define CONFIG_USB_STORAGE
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_ISO_PARTITION
> +#define CONFIG_SUPPORT_VFAT
> +#endif /* CONFIG_CMD_USB */
> +
> +#endif /* _CONFIG_OPENRD_BASE_H */
> --
Regards..
Prafulla . .
> 1.6.0.4
>
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2] Support for the OpenRD base board
2009-09-11 10:43 ` Prafulla Wadaskar
@ 2009-09-11 12:18 ` Simon Kagstrom
2009-09-11 13:33 ` Prafulla Wadaskar
0 siblings, 1 reply; 12+ messages in thread
From: Simon Kagstrom @ 2009-09-11 12:18 UTC (permalink / raw)
To: u-boot
Thanks for the comments Prafulla!
I'll update the patch according to them, but have some questions:
On Fri, 11 Sep 2009 03:43:04 -0700
Prafulla Wadaskar <prafulla@marvell.com> wrote:
> > +#define CONFIG_ENV_SIZE 0x20000 /* 128k */
> > +#define CONFIG_ENV_ADDR 0xa0000
> > +#define CONFIG_ENV_OFFSET 0xa0000 /* env starts here */
> Do you really need this address? the u-boot binary is within 256kb, at the most it can go till 512kb
This is where the default environment (for the U-boot shipped by
Marvell) resides. Like on Sheevaplug, it uses 4-bit ECC, so current
U-boot won't be able to read it, but I know you're working on it.
> > +#define MTDIDS_DEFAULT "nand0=nand_mtd"
> > +#define MTDPARTS_DEFAULT
> > "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(
> > uImage),"\
> > + "0x1fb00000 at 0x500000(rootfs)"
> This is must be the default setup in board setup file for openrd_base (if it is again derived from sheevaplug)
> In that case this settings not required
I don't quite understand this. This is also the default addresses
shipped with the board.
> > +#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
> > + "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
> > + "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
> > + "x_bootcmd_usb=usb start\0" \
> You must add x_bootcmd_eth for program MAC addrss in hardware before kernel boot.
Well, we need to figure out some generic way of giving Linux the MAC
address on these boards, but I've understood that initializing the
interface without using it is not popular, so in this case I'd just let
the problem remain (no x_bootcmd_eth).
Or did I misunderstand your comment?
// Simon
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2] Support for the OpenRD base board
2009-09-11 12:18 ` Simon Kagstrom
@ 2009-09-11 13:33 ` Prafulla Wadaskar
2009-09-11 13:52 ` Simon Kagstrom
0 siblings, 1 reply; 12+ messages in thread
From: Prafulla Wadaskar @ 2009-09-11 13:33 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Simon Kagstrom [mailto:simon.kagstrom at netinsight.net]
> Sent: Friday, September 11, 2009 5:48 PM
> To: Prafulla Wadaskar
> Cc: U-Boot ML; Dhaval Vasa; Prabhanjan Sarnaik; Ashish Karkare
> Subject: Re: [PATCH v2] Support for the OpenRD base board
>
> Thanks for the comments Prafulla!
>
> I'll update the patch according to them, but have some questions:
>
> On Fri, 11 Sep 2009 03:43:04 -0700
> Prafulla Wadaskar <prafulla@marvell.com> wrote:
>
> > > +#define CONFIG_ENV_SIZE 0x20000 /* 128k */
> > > +#define CONFIG_ENV_ADDR 0xa0000
> > > +#define CONFIG_ENV_OFFSET 0xa0000 /* env
> starts here */
> > Do you really need this address? the u-boot binary is
> within 256kb, at the most it can go till 512kb
>
> This is where the default environment (for the U-boot shipped by
> Marvell) resides. Like on Sheevaplug, it uses 4-bit ECC, so current
> U-boot won't be able to read it, but I know you're working on it.
So I think, you want to retain both environment variables untouched
( i.e. latest u-boot and u-boot shipped by Marvell)
But so far as mainlined u-boot is considered,
doesn't it make sense to pack uboot-bin and environment sector together?
like sheevaplug, I think first 2 sectors for u-boot and next once sector for env should be better to choose.
>
> > > +#define MTDIDS_DEFAULT "nand0=nand_mtd"
> > > +#define MTDPARTS_DEFAULT
> > > "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(
> > > uImage),"\
> > > + "0x1fb00000 at 0x500000(rootfs)"
> > This is must be the default setup in board setup file for
> openrd_base (if it is again derived from sheevaplug)
> > In that case this settings not required
>
> I don't quite understand this. This is also the default addresses
> shipped with the board.
W..r.to line 24 at http://git.marvell.com/?p=orion.git;a=blob;f=arch/arm/mach-kirkwood/openrd_base-setup.c;h=947dfb8cd5b252bf326d691ee5179e29ad07a9a9;hb=HEAD
By default kernel has same mdtpart configuration as you are describing here.
So you don't need this default setup here, you should skip it
>
> > > +#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
> > > + "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
> > > + "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
> > > + "x_bootcmd_usb=usb start\0" \
> > You must add x_bootcmd_eth for program MAC addrss in
> hardware before kernel boot.
>
> Well, we need to figure out some generic way of giving Linux the MAC
> address on these boards, but I've understood that initializing the
> interface without using it is not popular, so in this case
> I'd just let
> the problem remain (no x_bootcmd_eth).
Okay,
>
> Or did I misunderstand your comment?
No you understood it properly
As per my knowledge, I don't this the any hack for this in kernel will be accepted.
The same is with u-boot arm net drivers.
At both places fingures are crossed. s/w guys thinks h/w should take care of this.
But unfortunately this is not happening with this h/w (may be there are few more).
I personally feel that u-boot should handle this (copying ben for this)
Regards..
Prafulla . .
>
> // Simon
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2] Support for the OpenRD base board
2009-09-11 13:33 ` Prafulla Wadaskar
@ 2009-09-11 13:52 ` Simon Kagstrom
2009-09-12 17:54 ` Prafulla Wadaskar
0 siblings, 1 reply; 12+ messages in thread
From: Simon Kagstrom @ 2009-09-11 13:52 UTC (permalink / raw)
To: u-boot
On Fri, 11 Sep 2009 06:33:44 -0700
Prafulla Wadaskar <prafulla@marvell.com> wrote:
> > > > +#define CONFIG_ENV_SIZE 0x20000 /* 128k */
> > > > +#define CONFIG_ENV_ADDR 0xa0000
> > > > +#define CONFIG_ENV_OFFSET 0xa0000 /* env
> > starts here */
> > > Do you really need this address? the u-boot binary is
> > within 256kb, at the most it can go till 512kb
> >
> > This is where the default environment (for the U-boot shipped by
> > Marvell) resides. Like on Sheevaplug, it uses 4-bit ECC, so current
> > U-boot won't be able to read it, but I know you're working on it.
> So I think, you want to retain both environment variables untouched
> ( i.e. latest u-boot and u-boot shipped by Marvell)
> But so far as mainlined u-boot is considered,
> doesn't it make sense to pack uboot-bin and environment sector together?
> like sheevaplug, I think first 2 sectors for u-boot and next once sector for env should be better to choose.
Right, makes sense. I'll update that and skip the current address.
> > > > +#define MTDIDS_DEFAULT "nand0=nand_mtd"
> > > > +#define MTDPARTS_DEFAULT
> > > > "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(
> > > > uImage),"\
> > > > + "0x1fb00000 at 0x500000(rootfs)"
>
> > I don't quite understand this. This is also the default addresses
> > shipped with the board.
> W..r.to line 24 at http://git.marvell.com/?p=orion.git;a=blob;f=arch/arm/mach-kirkwood/openrd_base-setup.c;h=947dfb8cd5b252bf326d691ee5179e29ad07a9a9;hb=HEAD
> By default kernel has same mdtpart configuration as you are describing here.
> So you don't need this default setup here, you should skip it
OK, I understand. However, but it might also be useful from U-boot.
Locally, I've loaded the kernel from the ubifs partition, and then it's
useful to have this defined in U-boot as well. If it shouldn't be there
by default, I'll remove it though.
// Simon
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v2] Support for the OpenRD base board
2009-09-11 13:52 ` Simon Kagstrom
@ 2009-09-12 17:54 ` Prafulla Wadaskar
0 siblings, 0 replies; 12+ messages in thread
From: Prafulla Wadaskar @ 2009-09-12 17:54 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Simon Kagstrom [mailto:simon.kagstrom at netinsight.net]
> Sent: Friday, September 11, 2009 7:22 PM
> To: Prafulla Wadaskar
> Cc: U-Boot ML; Dhaval Vasa; Prabhanjan Sarnaik; Ashish
> Karkare; Ben Warren
> Subject: Re: [PATCH v2] Support for the OpenRD base board
>
> On Fri, 11 Sep 2009 06:33:44 -0700
> Prafulla Wadaskar <prafulla@marvell.com> wrote:
>
> > > > > +#define CONFIG_ENV_SIZE 0x20000
> /* 128k */
> > > > > +#define CONFIG_ENV_ADDR 0xa0000
> > > > > +#define CONFIG_ENV_OFFSET 0xa0000 /* env
> > > starts here */
> > > > Do you really need this address? the u-boot binary is
> > > within 256kb, at the most it can go till 512kb
> > >
> > > This is where the default environment (for the U-boot shipped by
> > > Marvell) resides. Like on Sheevaplug, it uses 4-bit ECC,
> so current
> > > U-boot won't be able to read it, but I know you're working on it.
> > So I think, you want to retain both environment variables untouched
> > ( i.e. latest u-boot and u-boot shipped by Marvell)
> > But so far as mainlined u-boot is considered,
> > doesn't it make sense to pack uboot-bin and environment
> sector together?
> > like sheevaplug, I think first 2 sectors for u-boot and
> next once sector for env should be better to choose.
>
> Right, makes sense. I'll update that and skip the current address.
>
> > > > > +#define MTDIDS_DEFAULT "nand0=nand_mtd"
> > > > > +#define MTDPARTS_DEFAULT
> > > > > "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(
> > > > > uImage),"\
> > > > > + "0x1fb00000 at 0x500000(rootfs)"
> >
> > > I don't quite understand this. This is also the default addresses
> > > shipped with the board.
>
> > W..r.to line 24 at
> http://git.marvell.com/?p=orion.git;a=blob;f=arch/arm/mach-kir
> kwood/openrd_base-setup.c;h=947dfb8cd5b252bf326d691ee5179e29ad
> 07a9a9;hb=HEAD
> > By default kernel has same mdtpart configuration as you are
> describing here.
> > So you don't need this default setup here, you should skip it
>
> OK, I understand. However, but it might also be useful from U-boot.
> Locally, I've loaded the kernel from the ubifs partition, and
> then it's
> useful to have this defined in U-boot as well. If it
> shouldn't be there
> by default, I'll remove it though.
Yes.
I leave decision up to you for this. My intension was to save some thing which is not required
Regards..
Prafulla. . .
>
> // Simon
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v3] Support for the OpenRD base board
2009-09-10 13:02 [U-Boot] [PATCH] Support for the OpenRD base board Simon Kagstrom
2009-09-11 8:14 ` [U-Boot] [PATCH v2] " Simon Kagstrom
@ 2009-09-14 7:46 ` Simon Kagstrom
2009-09-21 10:32 ` Prafulla Wadaskar
2009-09-21 10:54 ` [U-Boot] [PATCH v4] " Simon Kagstrom
2 siblings, 1 reply; 12+ messages in thread
From: Simon Kagstrom @ 2009-09-14 7:46 UTC (permalink / raw)
To: u-boot
Support for the OpenRD base board
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code and likely to be a bit incomplete.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
---
The configuration does not include UBIFS support, which still needs
the remaining patches for the bitops cleanup and fixes:
http://lists.denx.de/pipermail/u-boot/2009-August/059285.html
to build. Until those are applied, it's turned off here.
I get run-time problems when building for armv5te for OpenRD base
(apparently the same problem occurs for other Kirkwood boards). This
patch fixes that:
http://lists.denx.de/pipermail/u-boot/2009-September/059896.html
ChangeLog:
v2: kwbimage.cfg, which is needed to produce an image to install on the
NAND flash, has been added
v3: Updated after Prafullas review:
* Correct typo in comment section :-)
* Update copyright references
* Correct bit meaning in kwbimage.cfg according to new specification
* Add empty line after MPP configuration
* Use short name for board identity string in config
* Use CONFIG_SHEEVA_88SV131 instead of Feroceon
* Add CONFIG_KIRKWOOD_PCIE_INIT to config
* Use config_cmd_default.h and remove options which are not needed anymore
* Move config address to 0x60000 (384KB). I'd like it at this address since
adding UBI/UBIFS support to U-boot makes the binary a bit more than 300KB
and would thus overlap a config address at 0x40000.
Not updated in v3:
* The default MTD options are kept (useful for UBIFS)
* eth init is not done, this needs to be done in a generic way
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/openrd_base/Makefile | 56 ++++++++
board/Marvell/openrd_base/config.mk | 33 +++++
board/Marvell/openrd_base/kwbimage.cfg | 168 +++++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.c | 160 +++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.h | 46 +++++++
include/configs/openrd_base.h | 209 +++++++++++++++++++++++++++++++
9 files changed, 680 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/openrd_base/Makefile
create mode 100644 board/Marvell/openrd_base/config.mk
create mode 100644 board/Marvell/openrd_base/kwbimage.cfg
create mode 100644 board/Marvell/openrd_base/openrd_base.c
create mode 100644 board/Marvell/openrd_base/openrd_base.h
create mode 100644 include/configs/openrd_base.h
diff --git a/MAINTAINERS b/MAINTAINERS
index e9db278..99cdc12 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -588,6 +588,10 @@ Gary Jennejohn <garyj@denx.de>
Konstantin Kletschke <kletschke@synertronixx.de>
scb9328 ARM920T
+Simon Kagstrom <simon.kagstrom@netinsight.net>
+
+ openrd_base ARM926EJS (Kirkwood SoC)
+
Nishant Kamat <nskamat@ti.com>
omap1610h2 ARM926EJS
diff --git a/MAKEALL b/MAKEALL
index f0ed8ea..9e6eee2 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -533,6 +533,7 @@ LIST_ARM9=" \
omap1610inn \
omap5912osk \
omap730p2 \
+ openrd_base \
rd6281a \
sbc2410x \
scb9328 \
diff --git a/Makefile b/Makefile
index 9764cea..6cef82a 100644
--- a/Makefile
+++ b/Makefile
@@ -3022,6 +3022,9 @@ omap1610h2_cs_autoboot_config: unconfig
omap5912osk_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
+openrd_base_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
omap730p2_config \
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
new file mode 100644
index 0000000..3ef0b9b
--- /dev/null
+++ b/board/Marvell/openrd_base/Makefile
@@ -0,0 +1,56 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := openrd_base.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd_base/config.mk b/board/Marvell/openrd_base/config.mk
new file mode 100644
index 0000000..8ae355e
--- /dev/null
+++ b/board/Marvell/openrd_base/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg
new file mode 100644
index 0000000..757eb28
--- /dev/null
+++ b/board/Marvell/openrd_base/kwbimage.cfg
@@ -0,0 +1,168 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=x8
+# bit7-6: 11, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000042 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 1, DDR drive strength reduced
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
+# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
+# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
+# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+
+DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
+# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
+# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
+# bit14: 1, M_STARTBURST_IN ODT: Enabled
+# bit15: 1, DDR IO ODT Unit: Use ODT block
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
new file mode 100644
index 0000000..c00a08a
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.c
@@ -0,0 +1,160 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd_base.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(OPENRD_OE_VAL_LOW,
+ OPENRD_OE_VAL_HIGH,
+ OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD, /* Alt UART1_TXD */
+ MPP14_SD_D0, /* Alt UART1_RXD */
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO, /* UART1 / SD sel */
+ MPP35_TDM_CH0_TX_QL,
+ MPP36_TDM_SPI_CS1,
+ MPP37_TDM_CH2_TX_QL,
+ MPP38_TDM_CH2_RX_QL,
+ MPP39_AUDIO_I2SBCLK,
+ MPP40_AUDIO_I2SDO,
+ MPP41_AUDIO_I2SLRC,
+ MPP42_AUDIO_I2SMCLK,
+ MPP43_AUDIO_I2SDI,
+ MPP44_AUDIO_EXTCLK,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_TDM_CH0_RX_QL,
+ 0
+ };
+
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
new file mode 100644
index 0000000..f3daf17
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.h
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_BASE_H
+#define __OPENRD_BASE_H
+
+#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
+#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __OPENRD_BASE_H */
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
new file mode 100644
index 0000000..aea0dfb
--- /dev/null
+++ b/include/configs/openrd_base.h
@@ -0,0 +1,209 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_BASE_H
+#define _CONFIG_OPENRD_BASE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nOpenRD_base"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_BASE /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
+ "0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x8
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_OPENRD_BASE_H */
--
1.6.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v3] Support for the OpenRD base board
2009-09-14 7:46 ` [U-Boot] [PATCH v3] " Simon Kagstrom
@ 2009-09-21 10:32 ` Prafulla Wadaskar
0 siblings, 0 replies; 12+ messages in thread
From: Prafulla Wadaskar @ 2009-09-21 10:32 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Simon Kagstrom [mailto:simon.kagstrom at netinsight.net]
> Sent: Monday, September 14, 2009 1:17 PM
> To: U-Boot ML
> Cc: Prafulla Wadaskar; Dhaval Vasa; Prabhanjan Sarnaik; Ashish Karkare
> Subject: [PATCH v3] Support for the OpenRD base board
>
> Support for the OpenRD base board
Hi Simon
Two small things-
Can you pls remove this line, git log shows two lines since subject is also the same
>
> The implementation is borrowed from the sheevaplug board and
> the Marvell
> 1.1.4 code and likely to be a bit incomplete.
Though you have specified below ---,
it is better if you can specify what's incomplete here since it will appear in git log.
If that is UBIFS only, then I don't think it is incomplete :-)
Rest is okay
Regards..
Prafulla . .
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v4] Support for the OpenRD base board
2009-09-10 13:02 [U-Boot] [PATCH] Support for the OpenRD base board Simon Kagstrom
2009-09-11 8:14 ` [U-Boot] [PATCH v2] " Simon Kagstrom
2009-09-14 7:46 ` [U-Boot] [PATCH v3] " Simon Kagstrom
@ 2009-09-21 10:54 ` Simon Kagstrom
2009-09-21 16:47 ` Prafulla Wadaskar
2009-09-21 17:26 ` Prafulla Wadaskar
2 siblings, 2 replies; 12+ messages in thread
From: Simon Kagstrom @ 2009-09-21 10:54 UTC (permalink / raw)
To: u-boot
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
---
I get run-time problems when building for armv5te for OpenRD base
(apparently the same problem occurs for other Kirkwood boards).
ChangeLog:
v2: kwbimage.cfg, which is needed to produce an image to install on the
NAND flash, has been added
v3: Updated after Prafullas review:
* Correct typo in comment section :-)
* Update copyright references
* Correct bit meaning in kwbimage.cfg according to new specification
* Add empty line after MPP configuration
* Use short name for board identity string in config
* Use CONFIG_SHEEVA_88SV131 instead of Feroceon
* Add CONFIG_KIRKWOOD_PCIE_INIT to config
* Use config_cmd_default.h and remove options which are not needed anymore
* Move config address to 0x60000 (384KB). I'd like it at this address since
adding UBI/UBIFS support to U-boot makes the binary a bit more than 300KB
and would thus overlap a config address at 0x40000.
Not updated in v3:
* The default MTD options are kept (useful for UBIFS)
* eth init is not done, this needs to be done in a generic way
v4: Updated after Prafullas second review:
* Remove the double title line
* Change the description to note what's not tested
* Re-enable UBIFS since the bitops patch was merged
Thanks for the reviews, Prafulla!
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/openrd_base/Makefile | 56 ++++++++
board/Marvell/openrd_base/config.mk | 33 +++++
board/Marvell/openrd_base/kwbimage.cfg | 168 +++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.c | 160 ++++++++++++++++++++++
board/Marvell/openrd_base/openrd_base.h | 46 +++++++
include/configs/openrd_base.h | 220 +++++++++++++++++++++++++++++++
9 files changed, 691 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/openrd_base/Makefile
create mode 100644 board/Marvell/openrd_base/config.mk
create mode 100644 board/Marvell/openrd_base/kwbimage.cfg
create mode 100644 board/Marvell/openrd_base/openrd_base.c
create mode 100644 board/Marvell/openrd_base/openrd_base.h
create mode 100644 include/configs/openrd_base.h
diff --git a/MAINTAINERS b/MAINTAINERS
index f42c8f0..50f9260 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -588,6 +588,10 @@ Gary Jennejohn <garyj@denx.de>
Konstantin Kletschke <kletschke@synertronixx.de>
scb9328 ARM920T
+Simon Kagstrom <simon.kagstrom@netinsight.net>
+
+ openrd_base ARM926EJS (Kirkwood SoC)
+
Nishant Kamat <nskamat@ti.com>
omap1610h2 ARM926EJS
diff --git a/MAKEALL b/MAKEALL
index 1d50c34..a0a3006 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -533,6 +533,7 @@ LIST_ARM9=" \
omap1610inn \
omap5912osk \
omap730p2 \
+ openrd_base \
rd6281a \
sbc2410x \
scb9328 \
diff --git a/Makefile b/Makefile
index 0b61d05..8541b36 100644
--- a/Makefile
+++ b/Makefile
@@ -3022,6 +3022,9 @@ omap1610h2_cs_autoboot_config: unconfig
omap5912osk_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
+openrd_base_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
omap730p2_config \
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
new file mode 100644
index 0000000..3ef0b9b
--- /dev/null
+++ b/board/Marvell/openrd_base/Makefile
@@ -0,0 +1,56 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := openrd_base.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd_base/config.mk b/board/Marvell/openrd_base/config.mk
new file mode 100644
index 0000000..8ae355e
--- /dev/null
+++ b/board/Marvell/openrd_base/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg
new file mode 100644
index 0000000..757eb28
--- /dev/null
+++ b/board/Marvell/openrd_base/kwbimage.cfg
@@ -0,0 +1,168 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=x8
+# bit7-6: 11, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000042 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 1, DDR drive strength reduced
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
+# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
+# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
+# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+
+DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
+# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
+# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
+# bit14: 1, M_STARTBURST_IN ODT: Enabled
+# bit15: 1, DDR IO ODT Unit: Use ODT block
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
new file mode 100644
index 0000000..c00a08a
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.c
@@ -0,0 +1,160 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd_base.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(OPENRD_OE_VAL_LOW,
+ OPENRD_OE_VAL_HIGH,
+ OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD, /* Alt UART1_TXD */
+ MPP14_SD_D0, /* Alt UART1_RXD */
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO, /* UART1 / SD sel */
+ MPP35_TDM_CH0_TX_QL,
+ MPP36_TDM_SPI_CS1,
+ MPP37_TDM_CH2_TX_QL,
+ MPP38_TDM_CH2_RX_QL,
+ MPP39_AUDIO_I2SBCLK,
+ MPP40_AUDIO_I2SDO,
+ MPP41_AUDIO_I2SLRC,
+ MPP42_AUDIO_I2SMCLK,
+ MPP43_AUDIO_I2SDI,
+ MPP44_AUDIO_EXTCLK,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_TDM_CH0_RX_QL,
+ 0
+ };
+
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
new file mode 100644
index 0000000..f3daf17
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.h
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_BASE_H
+#define __OPENRD_BASE_H
+
+#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
+#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __OPENRD_BASE_H */
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
new file mode 100644
index 0000000..2aba0cb
--- /dev/null
+++ b/include/configs/openrd_base.h
@@ -0,0 +1,220 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_BASE_H
+#define _CONFIG_OPENRD_BASE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nOpenRD_base"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_BASE /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
+ "0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x8
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_OPENRD_BASE_H */
--
1.6.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v4] Support for the OpenRD base board
2009-09-21 10:54 ` [U-Boot] [PATCH v4] " Simon Kagstrom
@ 2009-09-21 16:47 ` Prafulla Wadaskar
2009-09-21 17:26 ` Prafulla Wadaskar
1 sibling, 0 replies; 12+ messages in thread
From: Prafulla Wadaskar @ 2009-09-21 16:47 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Simon Kagstrom [mailto:simon.kagstrom at netinsight.net]
> Sent: Monday, September 21, 2009 4:24 PM
> To: U-Boot ML
> Cc: Prafulla Wadaskar; Dhaval Vasa; Prabhanjan Sarnaik; Ashish Karkare
> Subject: Re: [U-Boot] [PATCH v4] Support for the OpenRD base board
>
> The implementation is borrowed from the sheevaplug board and
> the Marvell
> 1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
>
> Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
> ---
> I get run-time problems when building for armv5te for OpenRD base
> (apparently the same problem occurs for other Kirkwood boards).
>
>
> ChangeLog:
>
> v2: kwbimage.cfg, which is needed to produce an image to
> install on the
> NAND flash, has been added
> v3: Updated after Prafullas review:
> * Correct typo in comment section :-)
> * Update copyright references
> * Correct bit meaning in kwbimage.cfg according to new specification
> * Add empty line after MPP configuration
> * Use short name for board identity string in config
> * Use CONFIG_SHEEVA_88SV131 instead of Feroceon
> * Add CONFIG_KIRKWOOD_PCIE_INIT to config
> * Use config_cmd_default.h and remove options which are not
> needed anymore
> * Move config address to 0x60000 (384KB). I'd like it at
> this address since
> adding UBI/UBIFS support to U-boot makes the binary a bit
> more than 300KB
> and would thus overlap a config address at 0x40000.
> Not updated in v3:
> * The default MTD options are kept (useful for UBIFS)
> * eth init is not done, this needs to be done in a generic way
> v4: Updated after Prafullas second review:
> * Remove the double title line
> * Change the description to note what's not tested
> * Re-enable UBIFS since the bitops patch was merged
Oh that's great, so it's perfect now.
>
> Thanks for the reviews, Prafulla!
That's my pleasure too :-)
Regards..
Prafulla . .
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH v4] Support for the OpenRD base board
2009-09-21 10:54 ` [U-Boot] [PATCH v4] " Simon Kagstrom
2009-09-21 16:47 ` Prafulla Wadaskar
@ 2009-09-21 17:26 ` Prafulla Wadaskar
1 sibling, 0 replies; 12+ messages in thread
From: Prafulla Wadaskar @ 2009-09-21 17:26 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Simon Kagstrom [mailto:simon.kagstrom at netinsight.net]
> Sent: Monday, September 21, 2009 4:24 PM
> To: U-Boot ML
> Cc: Prafulla Wadaskar; Dhaval Vasa; Prabhanjan Sarnaik; Ashish Karkare
> Subject: Re: [U-Boot] [PATCH v4] Support for the OpenRD base board
>
> The implementation is borrowed from the sheevaplug board and
> the Marvell
> 1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
>
> Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
> ---
> I get run-time problems when building for armv5te for OpenRD base
> (apparently the same problem occurs for other Kirkwood boards).
>
>
> ChangeLog:
>
> v2: kwbimage.cfg, which is needed to produce an image to
> install on the
> NAND flash, has been added
> v3: Updated after Prafullas review:
> * Correct typo in comment section :-)
> * Update copyright references
> * Correct bit meaning in kwbimage.cfg according to new specification
> * Add empty line after MPP configuration
> * Use short name for board identity string in config
> * Use CONFIG_SHEEVA_88SV131 instead of Feroceon
> * Add CONFIG_KIRKWOOD_PCIE_INIT to config
> * Use config_cmd_default.h and remove options which are not
> needed anymore
> * Move config address to 0x60000 (384KB). I'd like it at
> this address since
> adding UBI/UBIFS support to U-boot makes the binary a bit
> more than 300KB
> and would thus overlap a config address at 0x40000.
> Not updated in v3:
> * The default MTD options are kept (useful for UBIFS)
> * eth init is not done, this needs to be done in a generic way
> v4: Updated after Prafullas second review:
> * Remove the double title line
> * Change the description to note what's not tested
> * Re-enable UBIFS since the bitops patch was merged
>
> Thanks for the reviews, Prafulla!
>
> MAINTAINERS | 4 +
> MAKEALL | 1 +
> Makefile | 3 +
> board/Marvell/openrd_base/Makefile | 56 ++++++++
> board/Marvell/openrd_base/config.mk | 33 +++++
> board/Marvell/openrd_base/kwbimage.cfg | 168
> +++++++++++++++++++++++
> board/Marvell/openrd_base/openrd_base.c | 160 ++++++++++++++++++++++
> board/Marvell/openrd_base/openrd_base.h | 46 +++++++
> include/configs/openrd_base.h | 220
> +++++++++++++++++++++++++++++++
> 9 files changed, 691 insertions(+), 0 deletions(-)
> create mode 100644 board/Marvell/openrd_base/Makefile
> create mode 100644 board/Marvell/openrd_base/config.mk
> create mode 100644 board/Marvell/openrd_base/kwbimage.cfg
> create mode 100644 board/Marvell/openrd_base/openrd_base.c
> create mode 100644 board/Marvell/openrd_base/openrd_base.h
> create mode 100644 include/configs/openrd_base.h
>
Applied to u-boot-marvell master branch
Regards..
Prafulla . .
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2009-09-21 17:26 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-09-10 13:02 [U-Boot] [PATCH] Support for the OpenRD base board Simon Kagstrom
2009-09-11 8:14 ` [U-Boot] [PATCH v2] " Simon Kagstrom
2009-09-11 10:43 ` Prafulla Wadaskar
2009-09-11 12:18 ` Simon Kagstrom
2009-09-11 13:33 ` Prafulla Wadaskar
2009-09-11 13:52 ` Simon Kagstrom
2009-09-12 17:54 ` Prafulla Wadaskar
2009-09-14 7:46 ` [U-Boot] [PATCH v3] " Simon Kagstrom
2009-09-21 10:32 ` Prafulla Wadaskar
2009-09-21 10:54 ` [U-Boot] [PATCH v4] " Simon Kagstrom
2009-09-21 16:47 ` Prafulla Wadaskar
2009-09-21 17:26 ` Prafulla Wadaskar
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.