* Cannot start array on disk [not found] <1124605843.526681.1468785592654.JavaMail.yahoo.ref@mail.yahoo.com> @ 2016-07-17 19:59 ` Bhatia Amit 2016-07-19 9:12 ` Phil Turmel 0 siblings, 1 reply; 12+ messages in thread From: Bhatia Amit @ 2016-07-17 19:59 UTC (permalink / raw) To: linux-raid Hi I have a WD Live duo setup with two 3TB drives in RAID1. After a recent power surge etc, I could not access the enclosure data. I removed the drives out from the enclosure and connected them via esata cable to a Linux laptop. One of the drives had physical noise and failed to connect at all. The other drive was able to connect and showed up as /dev/sdc. Following some online search, I issued the following commands to get some results, but am unable to mount the drive to a linux laptop via esata. Questions: * Ideally both sdc3 and sdc4 should have shown RAID=RAID1. If sdc4 is showing RAID=linear, is it because the other drive went totally bad, and software decided to reconfigure this drive from RAID1 to linear ? * Given the one of the two drives is totally dead, is it still possible to reconfigure, mount and recover data from the single drive? * I tried scanning the drive via r-linux and it does show files exist, but does not show any folder information. So data is there on the drive. Is there a way to recreate the setup with just this single drive, so that I can extract files with folder information? * Looking at an online "derrick" script, the script seems to call mdadm create with the "missing" flag. Is that something I should be doing to be able to assemble and recover data from the drive ? "mdadm --create $rootfsRaid --verbose --metadata=0.9 --raid-devices=2 --level=raid1 --run $diskRoot1 missing" Thanks Amit Parted shows missing filesystem for sdc4 : $ sudo parted -l Model: ATA WDC WD30EZRX-00D (scsi) Disk /dev/sdc: 3001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 3 15.7MB 528MB 513MB primary raid 1 528MB 2576MB 2048MB ext3 primary raid 2 2576MB 4624MB 2048MB ext3 primary raid 4 4624MB 3001GB 2996GB primary raid Mdstat shows only sdc3 as active, but sdc4 as inactive: $ sudo cat /proc/mdstat Personalities : [linear] [raid1] md126 : active (auto-read-only) raid1 sdc3[2] 500724 blocks super 1.0 [2/1] [_U] md127 : inactive sdc4[0](S) 2925750264 blocks super 1.0 unused devices: <none> Trying to assemble and scan only shows /dev/sdc3 as active: $ sudo mdadm --stop /dev/md12[567] mdadm: stopped /dev/md126 mdadm: stopped /dev/md127 $ sudo cat /proc/mdstat Personalities : [linear] [raid1] unused devices: <none> $ sudo mdadm --assemble --scan mdadm: /dev/md/MyBookLiveDuo:3 assembled from 1 drive - not enough to start the array. mdadm: /dev/md/MyBookLiveDuo:2 has been started with 1 drive (out of 2). mdadm: /dev/md/MyBookLiveDuo:3 assembled from 1 drive - not enough to start the array. $ sudo cat /proc/mdstat Personalities : [linear] [raid1] md127 : active raid1 sdc3[2] 500724 blocks super 1.0 [2/1] [_U] unused devices: <none> Output from examine sdc3 is below, which mdstat says is active. It says RAID level = RAID1. $ sudo mdadm --examine /dev/sdc3 /dev/sdc3: Magic : a92b4efc Version : 1.0 Feature Map : 0x0 Array UUID : 7c040c5e:9c30ac6d:e534a129:20457e22 Name : MyBookLiveDuo:2 Creation Time : Wed Dec 31 19:01:40 1969 Raid Level : raid1 Raid Devices : 2 Avail Dev Size : 1001448 (489.07 MiB 512.74 MB) Array Size : 500724 (489.07 MiB 512.74 MB) Super Offset : 1001456 sectors State : clean Device UUID : 1d9fe3e3:d5ac7387:d9ededba:88ca24a5 Update Time : Sun Jul 3 11:53:31 2016 Checksum : 31589560 - correct Events : 101 Device Role : Active device 1 Array State : .A ('A' == active, '.' == missing) $ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md126 : active (auto-read-only) raid1 sdc3[2] 500724 blocks super 1.0 [2/1] [_U] md127 : inactive sdc4[0](S) 2925750264 blocks super 1.0 unused devices: <none> But, output from examine sdc4 is below, which says RAID level = linear. $ sudo mdadm --examine /dev/sdc4 /dev/sdc4: Magic : a92b4efc Version : 1.0 Feature Map : 0x0 Array UUID : 374e689e:3bfd050c:ab0b0dce:2d50f5fd Name : MyBookLiveDuo:3 Creation Time : Mon Sep 16 14:53:47 2013 Raid Level : linear Raid Devices : 2 Avail Dev Size : 5851500528 (2790.21 GiB 2995.97 GB) Used Dev Size : 0 Super Offset : 5851500528 sectors State : clean Device UUID : 9096f74b:0a8f2b61:93347be3:6d3b6c1b Update Time : Mon Sep 16 14:53:47 2013 Checksum : 77aa5963 - correct Events : 0 Rounding : 0K Device Role : Active device 0 Array State : AA ('A' == active, '.' == missing) And partitions output is: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 1953411072 sda2 8 16 1953514584 sdb 8 17 248832 sdb1 8 18 1 sdb2 8 21 1953263616 sdb5 252 0 1953261568 dm-0 252 1 1919635456 dm-1 252 2 33488896 dm-2 8 32 2930266584 sdc 8 33 1999872 sdc1 8 34 1999872 sdc2 8 35 500736 sdc3 8 36 2925750272 sdc4 9 126 500724 md126 ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-17 19:59 ` Cannot start array on disk Bhatia Amit @ 2016-07-19 9:12 ` Phil Turmel 2016-07-20 2:10 ` Bhatia Amit 0 siblings, 1 reply; 12+ messages in thread From: Phil Turmel @ 2016-07-19 9:12 UTC (permalink / raw) To: Bhatia Amit, linux-raid On 07/17/2016 03:59 PM, Bhatia Amit wrote: > Hi > > I have a WD Live duo setup with two 3TB drives in RAID1. After a > recent power surge etc, I could not access the enclosure data. I > removed the drives out from the enclosure and connected them via > esata cable to a Linux laptop. One of the drives had physical noise > and failed to connect at all. The other drive was able to connect and > showed up as /dev/sdc. Following some online search, I issued the > following commands to get some results, but am unable to mount the > drive to a linux laptop via esata. Questions: > > * Ideally both sdc3 and sdc4 should have shown RAID=RAID1. If sdc4 is > showing RAID=linear, is it because the other drive went totally bad, > and software decided to reconfigure this drive from RAID1 to linear > ? No way to know. I would be inclined to believe that that you didn't actually have raid1 set for those partitions. Do you recall the available space in that device while running? > * Given the one of the two drives is totally dead, is it still > possible to reconfigure, mount and recover data from the single > drive? If truly linear, no, not past the half-way mark. The device is identified as role 0, so it would be the beginning of the filesystem in a linear array. If it really was raid1 with v0.9 or v1.0 metadata, you can mount /dev/sdc4 directly to access your data. That it doesn't show a detected filesystem suggests that it wasn't raid1. Even worse, that partition shows a creation date and update date both in 2013, with no events. Suggesting that the device hasn't actually been running properly in the array since its initial creation. > * I tried scanning the drive via r-linux and it does show files > exist, but does not show any folder information. So data is there on > the drive. Is there a way to recreate the setup with just this single > drive, so that I can extract files with folder information? With v1.0 metadata, you should be able to fsck /dev/sdc4 and then mount. Kinda dangerous though -- I suggest you use an overlay for that. I suspect that sdc4 hasn't been running in your array for the past three years. > * Looking at an online "derrick" script, the script seems to call > mdadm create with the "missing" flag. Is that something I should be > doing to be able to assemble and recover data from the drive ? > "mdadm --create $rootfsRaid --verbose --metadata=0.9 --raid-devices=2 > --level=raid1 --run $diskRoot1 missing" No. Using --create is practically never the right solution, unless you've done operations that destroy the right solution. Metadata v0.9 is almost certainly wrong. If you have syslogs on your other array that show the boot details from the last successful boot *before* it died, that might provide the details needed to figure if anything recent is on sdc4. Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-19 9:12 ` Phil Turmel @ 2016-07-20 2:10 ` Bhatia Amit 2016-07-20 2:52 ` Bhatia Amit 0 siblings, 1 reply; 12+ messages in thread From: Bhatia Amit @ 2016-07-20 2:10 UTC (permalink / raw) To: Phil Turmel, linux-raid Hi Phil 1. The enclosure had 2 drives in RAID1, since 2013. One drive went bad early this year around Feb 2016 (Drive A). WDC gave a RMA replacement drive. I remember accessing the enclosure at least once after the RMA drive rebuilt. This drive A is the one that is still alive. The drive B went bad recently (June 2016) after which I was unable to access the system at all. 2. The drive should be around 1/3rd used i.e around 1TB out of 3TB drive should be used. 3. Connecting this drive via esata to a linux laptop, gparted shows sdc1 and sdc2 as EXT3 of 1.91GB each, and sdc3 (489MB) and sdc4 (2.72TB) as linux-raid filesystem. 4. I mounted sdc1 and sdc2 and var/log directories on both look like copy of each other: $ ls -lart p1/var/log total 1136 -rw-rw-rw- 1 root root 31 Dec 31 1969 master_drive_serial_number drwxr-xr-x 2 root root 4096 Mar 24 2010 sysstat drwxr-xr-x 2 root root 4096 Sep 16 2013 apt -rw-rw-rw- 1 root adm 4734 Sep 16 2013 dmesg.4.gz -rw-rw-rw- 1 root adm 4799 Sep 16 2013 dmesg.3.gz drwxr-xr-- 2 root root 4096 Sep 16 2013 news -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.warn -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.log -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.info -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.err -rw-r--r-- 1 root adm 0 Sep 16 2013 lpr.log drwxr-xr-x 2 root root 4096 Sep 16 2013 apache2 -rw-rw-rw- 1 root adm 14889 May 7 2015 dmesg.0 -rw-r--r-- 1 root adm 0 May 7 2015 sshd.log -rw-r--r-- 1 root adm 1765 May 7 2015 kern.log -rw-r--r-- 1 root root 1504 May 7 2015 dpkg.log -rw-r----- 1 root adm 0 Jul 1 22:38 vsftpd.log drwxr-xr-x 3 root root 4096 Jul 1 22:38 samba -rw-rw-rw- 1 root adm 4747 Jul 1 22:42 dmesg.2.gz -rw-rw-rw- 1 root adm 4747 Jul 1 22:48 dmesg.1.gz -rw-rw-rw- 1 root root 154 Jul 1 23:01 version.log drwxr-xr-x 14 root root 4096 Jul 1 23:06 .. -rw-r--r-- 1 root adm 75 Jul 1 23:06 wdalerts.log -rw-r--r-- 1 root adm 15259 Jul 1 23:10 wdnas.log -rw-r--r-- 1 root root 3067 Jul 1 23:10 forked-daapd.log -rw-r--r-- 1 root adm 32586 Jul 1 23:11 user.log -rw-r--r-- 1 root adm 74 Jul 1 23:11 dlna_server.log -rw-r--r-- 1 root adm 4243 Jul 1 23:11 miocrawler.log -rw-r--r-- 1 root adm 21531 Jul 1 23:12 mediacrawler.log -rw-r--r-- 1 root adm 643021 Jul 2 00:02 rest_api.log.1 -rw-r--r-- 1 root adm 151111 Jul 2 00:02 messages -rw-r--r-- 1 root adm 31328 Jul 2 02:14 daemon.log -rw-rw-rw- 1 root root 720 Jul 2 03:00 ramlog -rw-rw-rw- 1 root adm 15162 Jul 2 12:02 dmesg -rw-rw-rw- 1 root root 108362 Jul 2 12:02 rest_api.log -rw-rw-rw- 1 root root 58 Jul 2 12:02 purge.log drwxr-xr-x 7 root root 4096 Jul 2 12:02 . 5. A grep of raid or sd or ext, on messages shows: $ cat p1/var/log/messages | egrep -i "sd|raid|ext" Sep 16 11:53:17 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts Sep 16 11:53:17 MyBookLiveDuo kernel: Kernel command line: root=/dev/md0 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) Sep 16 11:53:17 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 Sep 16 11:53:17 MyBookLiveDuo kernel: sda: Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Sep 16 11:53:17 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots Sep 16 11:53:17 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 Sep 16 11:53:17 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk Sep 16 11:53:17 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect Sep 16 11:53:17 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. Sep 16 11:53:17 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: considering sdb2 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sdb2 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sdb1 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sda2 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sda1 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sda1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sda2> Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sdb1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sdb2> Sep 16 11:53:17 MyBookLiveDuo kernel: md: running: <sdb2><sdb1><sda2><sda1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: kicking non-fresh sdb2 from array! Sep 16 11:53:17 MyBookLiveDuo kernel: md: unbind<sdb2> Sep 16 11:53:17 MyBookLiveDuo kernel: md: export_rdev(sdb2) Sep 16 11:53:17 MyBookLiveDuo kernel: md: kicking non-fresh sdb1 from array! Sep 16 11:53:17 MyBookLiveDuo kernel: md: unbind<sdb1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: export_rdev(sdb1) Sep 16 11:53:17 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. Sep 16 11:53:17 MyBookLiveDuo kernel: raid1: raid set md0 active with 2 out of 4 mirrors Sep 16 11:53:17 MyBookLiveDuo kernel: EXT3 FS on md0, internal journal Sep 16 11:53:17 MyBookLiveDuo kernel: EXT3-fs: recovery complete. Sep 16 11:53:17 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. Sep 16 11:53:17 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:0. Sep 16 11:53:25 MyBookLiveDuo kernel: md: bind<sdb3> Sep 16 11:53:25 MyBookLiveDuo kernel: md: bind<sda3> Sep 16 11:53:25 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors Sep 16 11:53:36 MyBookLiveDuo [admin-rest-api.postinst] 09/16/13 18:53:36: test context=test Sep 16 11:53:40 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k Sep 16 11:54:02 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. Sep 16 11:54:02 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. Sep 16 11:54:02 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d1790000 Jul 1 19:39:01 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:39:01 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:39:01 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:39:01 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:39:01 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:39:01 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:39:01 MyBookLiveDuo kernel: disk 2, wo:1, o:1, dev:sdb1 Jul 1 19:39:02 MyBookLiveDuo kernel: md: recovery of RAID array md0 Jul 1 19:39:02 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 19:39:40 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:39:40 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb1 Jul 1 19:39:40 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:39:40 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb1 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 3, wo:1, o:1, dev:sdb2 Jul 1 19:39:41 MyBookLiveDuo kernel: md: recovery of RAID array md0 Jul 1 19:40:18 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:40:18 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:40:18 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:40:18 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb1 Jul 1 19:40:18 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sdb2 Jul 1 19:42:02 MyBookLiveDuo kernel: nfsd: last server has exited, flushing export cache Jul 1 19:42:02 MyBookLiveDuo kernel: ufsd: driver unloaded Jul 1 19:42:26 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts Jul 1 19:42:26 MyBookLiveDuo kernel: Kernel command line: root=/dev/md0 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) Jul 1 19:42:26 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 Jul 1 19:42:26 MyBookLiveDuo kernel: sda: Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:42:26 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots Jul 1 19:42:26 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 Jul 1 19:42:26 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk Jul 1 19:42:26 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect Jul 1 19:42:26 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. Jul 1 19:42:26 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: considering sdb2 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sdb2 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sdb1 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sda2 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sda1 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sda1> Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sda2> Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 19:42:26 MyBookLiveDuo kernel: md: running: <sdb2><sdb1><sda2><sda1> Jul 1 19:42:26 MyBookLiveDuo kernel: md0: WARNING: sdb2 appears to be on the same physical disk as sdb1. Jul 1 19:42:26 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. Jul 1 19:42:26 MyBookLiveDuo kernel: raid1: raid set md0 active with 4 out of 4 mirrors Jul 1 19:42:26 MyBookLiveDuo kernel: EXT3 FS on md0, internal journal Jul 1 19:42:26 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. Jul 1 19:42:26 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:0. Jul 1 19:42:32 MyBookLiveDuo kernel: md: bind<sdb3> Jul 1 19:42:32 MyBookLiveDuo kernel: md: bind<sda3> Jul 1 19:42:32 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors Jul 1 19:42:40 MyBookLiveDuo [admin-rest-api.postinst] 07/02/16 02:42:40: test context=test Jul 1 19:42:44 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k Jul 1 19:43:06 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. Jul 1 19:43:06 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. Jul 1 19:43:06 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d1790000 Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sdb1 from md0 ... Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sdb2 from md0 ... Jul 1 19:47:30 MyBookLiveDuo kernel: nfsd: last server has exited, flushing export cache Jul 1 19:47:31 MyBookLiveDuo kernel: ufsd: driver unloaded Jul 1 19:48:09 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts Jul 1 19:48:09 MyBookLiveDuo kernel: Kernel command line: root=/dev/md0 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) Jul 1 19:48:09 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 Jul 1 19:48:09 MyBookLiveDuo kernel: sda: Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:48:09 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots Jul 1 19:48:09 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 Jul 1 19:48:09 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk Jul 1 19:48:09 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect Jul 1 19:48:09 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. Jul 1 19:48:09 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: considering sdb2 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sdb2 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sdb1 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sda2 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sda1 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sda1> Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sda2> Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 19:48:09 MyBookLiveDuo kernel: md: running: <sdb2><sdb1><sda2><sda1> Jul 1 19:48:09 MyBookLiveDuo kernel: md0: WARNING: sdb2 appears to be on the same physical disk as sdb1. Jul 1 19:48:09 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. Jul 1 19:48:09 MyBookLiveDuo kernel: raid1: raid set md0 active with 4 out of 4 mirrors Jul 1 19:48:09 MyBookLiveDuo kernel: EXT3 FS on md0, internal journal Jul 1 19:48:09 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. Jul 1 19:48:09 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:0. Jul 1 19:48:13 MyBookLiveDuo kernel: md: bind<sda4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: bind<sdb4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: unbind<sdb4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: export_rdev(sdb4) Jul 1 19:48:13 MyBookLiveDuo kernel: md: unbind<sda4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: export_rdev(sda4) Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sdb3> Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sda3> Jul 1 19:48:15 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sdb4> Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sda4> Jul 1 19:53:51 MyBookLiveDuo kernel: EXT4-fs (md3): mounted filesystem with ordered data mode Jul 1 19:53:56 MyBookLiveDuo [wd-nas.postinst] 07/02/16 02:53:55: restore context=restore Jul 1 19:54:00 MyBookLiveDuo [networking-general.postinst] 07/02/16 02:54:00: restore context=restore Jul 1 19:54:01 MyBookLiveDuo [apache-php-webdav.postinst] 07/02/16 02:54:01: restore context=restore Jul 1 19:54:06 MyBookLiveDuo [date-time.postinst] 07/02/16 02:54:06: restore context=restore Jul 1 19:54:09 MyBookLiveDuo [alerts.postinst] 07/02/16 02:54:09: restore context=restore Jul 1 19:54:10 MyBookLiveDuo [admin-rest-api.postinst] 07/02/16 02:54:10: restore context=restore Jul 1 19:54:12 MyBookLiveDuo [drive-lib.postinst] 07/02/16 02:54:12: restore context=restore Jul 1 19:54:13 MyBookLiveDuo [data-volume-config.postinst] 07/02/16 02:54:13: restore context=restore Jul 1 19:54:14 MyBookLiveDuo [upnp-nas.postinst] 07/02/16 02:54:14: restore context=restore Jul 1 19:54:15 MyBookLiveDuo [dlna-server-access.postinst] 07/02/16 02:54:15: restore context=restore Jul 1 19:54:16 MyBookLiveDuo [itunes.postinst] 07/02/16 02:54:16: restore context=restore Jul 1 19:54:17 MyBookLiveDuo [nas-safepoint.postinst] 07/02/16 02:54:17: restore context=restore Jul 1 19:54:18 MyBookLiveDuo [webui.postinst] 07/02/16 02:54:18: restore context=restore Jul 1 19:54:28 MyBookLiveDuo [orion-resources.postinst] 07/02/16 02:54:28: restore context=restore Jul 1 19:54:29 MyBookLiveDuo [afp.postinst] 07/02/16 02:54:29: restore context=restore Jul 1 19:54:29 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k Jul 1 19:55:18 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:55:19 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:55:19 MyBookLiveDuo kernel: md: cannot remove active disk sdb1 from md0 ... Jul 1 19:55:19 MyBookLiveDuo kernel: md: cannot remove active disk sdb2 from md0 ... Jul 1 19:55:28 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. Jul 1 19:55:28 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. Jul 1 19:55:28 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d3b00000 Jul 1 19:55:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:55:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 2, wo:1, o:0, dev:sdb1 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sdb2 Jul 1 19:55:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:55:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sdb2 Jul 1 19:55:31 MyBookLiveDuo kernel: md: unbind<sdb1> Jul 1 19:55:31 MyBookLiveDuo kernel: md: export_rdev(sdb1) Jul 1 19:55:32 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:55:32 MyBookLiveDuo kernel: raid1: raid set md1 active with 1 out of 4 mirrors Jul 1 19:58:57 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:58:57 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:58:57 MyBookLiveDuo kernel: md: cannot remove active disk sdb2 from md0 ... Jul 1 20:00:59 MyBookLiveDuo kernel: EXT3-fs warning: checktime reached, running e2fsck is recommended Jul 1 20:00:59 MyBookLiveDuo kernel: EXT3 FS on md1, internal journal Jul 1 20:00:59 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with writeback data mode. May 7 18:23:57 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts May 7 18:23:57 MyBookLiveDuo kernel: Kernel command line: root=/dev/md1 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) May 7 18:23:57 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). May 7 18:23:57 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 May 7 18:23:57 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 May 7 18:23:57 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 May 7 18:23:57 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 May 7 18:23:57 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 May 7 18:23:57 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 May 7 18:23:57 MyBookLiveDuo kernel: sda: May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA May 7 18:23:57 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots May 7 18:23:57 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 May 7 18:23:57 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk May 7 18:23:57 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect May 7 18:23:57 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. May 7 18:23:57 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: considering sdb2 ... May 7 18:23:57 MyBookLiveDuo kernel: md: adding sdb2 ... May 7 18:23:57 MyBookLiveDuo kernel: md: sdb1 has different UUID to sdb2 May 7 18:23:57 MyBookLiveDuo kernel: md: adding sda2 ... May 7 18:23:57 MyBookLiveDuo kernel: md: adding sda1 ... May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sda1> May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sda2> May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sdb2> May 7 18:23:57 MyBookLiveDuo kernel: md: running: <sdb2><sda2><sda1> May 7 18:23:57 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. May 7 18:23:57 MyBookLiveDuo kernel: raid1: raid set md0 active with 3 out of 4 mirrors May 7 18:23:57 MyBookLiveDuo kernel: md: considering sdb1 ... May 7 18:23:57 MyBookLiveDuo kernel: md: adding sdb1 ... May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sdb1> May 7 18:23:57 MyBookLiveDuo kernel: md: running: <sdb1> May 7 18:23:57 MyBookLiveDuo kernel: raid1: raid set md1 active with 1 out of 4 mirrors May 7 18:23:57 MyBookLiveDuo kernel: EXT3 FS on md1, internal journal May 7 18:23:57 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. May 7 18:23:57 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:1. May 7 18:24:01 MyBookLiveDuo kernel: md: bind<sdb3> May 7 18:24:01 MyBookLiveDuo kernel: md: bind<sda3> May 7 18:24:01 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors May 7 18:24:02 MyBookLiveDuo kernel: md: bind<sdb4> May 7 18:24:02 MyBookLiveDuo kernel: md: bind<sda4> May 7 18:24:02 MyBookLiveDuo kernel: EXT4-fs (md3): mounted filesystem with ordered data mode May 7 18:24:10 MyBookLiveDuo [admin-rest-api.postinst] 05/08/15 01:24:10: test context=test May 7 18:24:14 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k May 7 18:24:23 MyBookLiveDuo [dlna-server-access.postinst] 05/08/15 01:24:23: configure 02.00.00-100316 context=upgrade May 7 18:24:52 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. May 7 18:24:52 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. May 7 18:24:52 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d2750000 Jul 1 20:06:48 MyBookLiveDuo kernel: md: unbind<sdb2> Jul 1 20:06:48 MyBookLiveDuo kernel: md: export_rdev(sdb2) Jul 1 20:06:48 MyBookLiveDuo kernel: md: unbind<sda2> Jul 1 20:06:48 MyBookLiveDuo kernel: md: export_rdev(sda2) Jul 1 20:06:48 MyBookLiveDuo kernel: md: unbind<sda1> Jul 1 20:06:48 MyBookLiveDuo kernel: md: export_rdev(sda1) Jul 1 20:06:50 MyBookLiveDuo kernel: md: bind<sda1> Jul 1 20:06:50 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:06:50 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:06:50 MyBookLiveDuo kernel: disk 1, wo:1, o:1, dev:sda1 Jul 1 20:06:50 MyBookLiveDuo kernel: md: recovery of RAID array md1 Jul 1 20:06:50 MyBookLiveDuo kernel: md: bind<sda2> Jul 1 20:06:50 MyBookLiveDuo kernel: md: cannot remove active disk sdb1 from md1 ... Jul 1 20:06:50 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 20:07:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:07:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:07:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:07:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 2, wo:1, o:1, dev:sdb2 Jul 1 20:07:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:07:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 2, wo:1, o:1, dev:sdb2 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 3, wo:1, o:1, dev:sda2 Jul 1 20:07:31 MyBookLiveDuo kernel: md: recovery of RAID array md1 Jul 1 20:08:39 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:08:39 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:08:39 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:08:39 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb2 Jul 1 20:08:39 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sda2 Jul 1 20:09:54 MyBookLiveDuo kernel: nfsd: last server has exited, flushing export cache Jul 1 20:10:49 MyBookLiveDuo kernel: md: unbind<sda4> Jul 1 20:10:49 MyBookLiveDuo kernel: md: export_rdev(sda4) Jul 1 20:10:49 MyBookLiveDuo kernel: md: unbind<sdb4> Jul 1 20:10:49 MyBookLiveDuo kernel: md: export_rdev(sdb4) Jul 1 20:10:51 MyBookLiveDuo kernel: md: bind<sda4> Jul 1 20:10:51 MyBookLiveDuo kernel: raid1: raid set md3 active with 1 out of 2 mirrors Jul 1 20:10:51 MyBookLiveDuo kernel: md: bind<sdb4> Jul 1 20:10:51 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:10:51 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda4 Jul 1 20:10:51 MyBookLiveDuo kernel: disk 1, wo:1, o:1, dev:sdb4 Jul 1 20:10:51 MyBookLiveDuo kernel: md: recovery of RAID array md3 Jul 1 20:10:51 MyBookLiveDuo kernel: EXT4-fs (md3): mounted filesystem with ordered data mode The messages file has 1922 lines, so I am not pasting the whole content here yet, unless you suggest. 6. Trying to mount sdc4 as ext4 fails: $ sudo mount -t ext4 /dev/sdc4 p4 mount: /dev/sdc4 already mounted or p4 busy Is there a way to confirm whether sdc4 was ext4 (as r-linux) had reported, or ext3? 7. Before trying to do fsck on sdc4, I wanted to check if you had any other suggestion based on info above. Also, looks like for fsck I should be providing filesystem type. So, wanted to check if I should try ext3 or ext4 on sdc4, when trying fsck. Thanks Amit ----- Original Message ----- From: Phil Turmel <philip@turmel.org> To: Bhatia Amit <amitbhatia@rocketmail.com>; "linux-raid@vger.kernel.org" <linux-raid@vger.kernel.org> Sent: Tuesday, July 19, 2016 5:12 AM Subject: Re: Cannot start array on disk On 07/17/2016 03:59 PM, Bhatia Amit wrote: > Hi > > I have a WD Live duo setup with two 3TB drives in RAID1. After a > recent power surge etc, I could not access the enclosure data. I > removed the drives out from the enclosure and connected them via > esata cable to a Linux laptop. One of the drives had physical noise > and failed to connect at all. The other drive was able to connect and > showed up as /dev/sdc. Following some online search, I issued the > following commands to get some results, but am unable to mount the > drive to a linux laptop via esata. Questions: > > * Ideally both sdc3 and sdc4 should have shown RAID=RAID1. If sdc4 is > showing RAID=linear, is it because the other drive went totally bad, > and software decided to reconfigure this drive from RAID1 to linear > ? No way to know. I would be inclined to believe that that you didn't actually have raid1 set for those partitions. Do you recall the available space in that device while running? > * Given the one of the two drives is totally dead, is it still > possible to reconfigure, mount and recover data from the single > drive? If truly linear, no, not past the half-way mark. The device is identified as role 0, so it would be the beginning of the filesystem in a linear array. If it really was raid1 with v0.9 or v1.0 metadata, you can mount /dev/sdc4 directly to access your data. That it doesn't show a detected filesystem suggests that it wasn't raid1. Even worse, that partition shows a creation date and update date both in 2013, with no events. Suggesting that the device hasn't actually been running properly in the array since its initial creation. > * I tried scanning the drive via r-linux and it does show files > exist, but does not show any folder information. So data is there on > the drive. Is there a way to recreate the setup with just this single > drive, so that I can extract files with folder information? With v1.0 metadata, you should be able to fsck /dev/sdc4 and then mount. Kinda dangerous though -- I suggest you use an overlay for that. I suspect that sdc4 hasn't been running in your array for the past three years. > * Looking at an online "derrick" script, the script seems to call > mdadm create with the "missing" flag. Is that something I should be > doing to be able to assemble and recover data from the drive ? > "mdadm --create $rootfsRaid --verbose --metadata=0.9 --raid-devices=2 > --level=raid1 --run $diskRoot1 missing" No. Using --create is practically never the right solution, unless you've done operations that destroy the right solution. Metadata v0.9 is almost certainly wrong. If you have syslogs on your other array that show the boot details from the last successful boot *before* it died, that might provide the details needed to figure if anything recent is on sdc4. Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-20 2:10 ` Bhatia Amit @ 2016-07-20 2:52 ` Bhatia Amit 2016-07-20 10:30 ` Phil Turmel 0 siblings, 1 reply; 12+ messages in thread From: Bhatia Amit @ 2016-07-20 2:52 UTC (permalink / raw) To: Bhatia Amit, Phil Turmel, linux-raid Hi Phil One more thing. When the enclosure became inaccesible in June 2016, WDC gave me a new unit with drives. I dont remember for sure, but I think I first replaced drive A from new enclosure with the Drive A (currently in discussion) from old enclosure, hoping new unit would reconfigure based on info from old drive. But I was not able to access the unit. Then I put back the two new drives back in new enclosure, configured new unit for RAID1 and then replaced the drive A again with the drive A from old enclosure, but again no luck accessing it (Error Message=Unable to mount). Since the default configuration of a new configuration is Striping and not RAID1, probably the first action (replacing drive A before configuring new unit for RAID1), might have been the cause why this drive A shows as RAID =linear, rather than RAID1. Thanks Amit ----- Original Message ----- From: Bhatia Amit <amitbhatia@rocketmail.com> To: Phil Turmel <philip@turmel.org>; "linux-raid@vger.kernel.org" <linux-raid@vger.kernel.org> Sent: Tuesday, July 19, 2016 10:10 PM Subject: Re: Cannot start array on disk Hi Phil 1. The enclosure had 2 drives in RAID1, since 2013. One drive went bad early this year around Feb 2016 (Drive A). WDC gave a RMA replacement drive. I remember accessing the enclosure at least once after the RMA drive rebuilt. This drive A is the one that is still alive. The drive B went bad recently (June 2016) after which I was unable to access the system at all. 2. The drive should be around 1/3rd used i.e around 1TB out of 3TB drive should be used. 3. Connecting this drive via esata to a linux laptop, gparted shows sdc1 and sdc2 as EXT3 of 1.91GB each, and sdc3 (489MB) and sdc4 (2.72TB) as linux-raid filesystem. 4. I mounted sdc1 and sdc2 and var/log directories on both look like copy of each other: $ ls -lart p1/var/log total 1136 -rw-rw-rw- 1 root root 31 Dec 31 1969 master_drive_serial_number drwxr-xr-x 2 root root 4096 Mar 24 2010 sysstat drwxr-xr-x 2 root root 4096 Sep 16 2013 apt -rw-rw-rw- 1 root adm 4734 Sep 16 2013 dmesg.4.gz -rw-rw-rw- 1 root adm 4799 Sep 16 2013 dmesg.3.gz drwxr-xr-- 2 root root 4096 Sep 16 2013 news -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.warn -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.log -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.info -rw-r--r-- 1 root adm 0 Sep 16 2013 mail.err -rw-r--r-- 1 root adm 0 Sep 16 2013 lpr.log drwxr-xr-x 2 root root 4096 Sep 16 2013 apache2 -rw-rw-rw- 1 root adm 14889 May 7 2015 dmesg.0 -rw-r--r-- 1 root adm 0 May 7 2015 sshd.log -rw-r--r-- 1 root adm 1765 May 7 2015 kern.log -rw-r--r-- 1 root root 1504 May 7 2015 dpkg.log -rw-r----- 1 root adm 0 Jul 1 22:38 vsftpd.log drwxr-xr-x 3 root root 4096 Jul 1 22:38 samba -rw-rw-rw- 1 root adm 4747 Jul 1 22:42 dmesg.2.gz -rw-rw-rw- 1 root adm 4747 Jul 1 22:48 dmesg.1.gz -rw-rw-rw- 1 root root 154 Jul 1 23:01 version.log drwxr-xr-x 14 root root 4096 Jul 1 23:06 .. -rw-r--r-- 1 root adm 75 Jul 1 23:06 wdalerts.log -rw-r--r-- 1 root adm 15259 Jul 1 23:10 wdnas.log -rw-r--r-- 1 root root 3067 Jul 1 23:10 forked-daapd.log -rw-r--r-- 1 root adm 32586 Jul 1 23:11 user.log -rw-r--r-- 1 root adm 74 Jul 1 23:11 dlna_server.log -rw-r--r-- 1 root adm 4243 Jul 1 23:11 miocrawler.log -rw-r--r-- 1 root adm 21531 Jul 1 23:12 mediacrawler.log -rw-r--r-- 1 root adm 643021 Jul 2 00:02 rest_api.log.1 -rw-r--r-- 1 root adm 151111 Jul 2 00:02 messages -rw-r--r-- 1 root adm 31328 Jul 2 02:14 daemon.log -rw-rw-rw- 1 root root 720 Jul 2 03:00 ramlog -rw-rw-rw- 1 root adm 15162 Jul 2 12:02 dmesg -rw-rw-rw- 1 root root 108362 Jul 2 12:02 rest_api.log -rw-rw-rw- 1 root root 58 Jul 2 12:02 purge.log drwxr-xr-x 7 root root 4096 Jul 2 12:02 . 5. A grep of raid or sd or ext, on messages shows: $ cat p1/var/log/messages | egrep -i "sd|raid|ext" Sep 16 11:53:17 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts Sep 16 11:53:17 MyBookLiveDuo kernel: Kernel command line: root=/dev/md0 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s Sep 16 11:53:17 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) Sep 16 11:53:17 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 Sep 16 11:53:17 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 Sep 16 11:53:17 MyBookLiveDuo kernel: sda: Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Sep 16 11:53:17 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots Sep 16 11:53:17 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 Sep 16 11:53:17 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 Sep 16 11:53:17 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk Sep 16 11:53:17 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk Sep 16 11:53:17 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect Sep 16 11:53:17 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. Sep 16 11:53:17 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! Sep 16 11:53:17 MyBookLiveDuo kernel: md: considering sdb2 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sdb2 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sdb1 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sda2 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: adding sda1 ... Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sda1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sda2> Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sdb1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: bind<sdb2> Sep 16 11:53:17 MyBookLiveDuo kernel: md: running: <sdb2><sdb1><sda2><sda1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: kicking non-fresh sdb2 from array! Sep 16 11:53:17 MyBookLiveDuo kernel: md: unbind<sdb2> Sep 16 11:53:17 MyBookLiveDuo kernel: md: export_rdev(sdb2) Sep 16 11:53:17 MyBookLiveDuo kernel: md: kicking non-fresh sdb1 from array! Sep 16 11:53:17 MyBookLiveDuo kernel: md: unbind<sdb1> Sep 16 11:53:17 MyBookLiveDuo kernel: md: export_rdev(sdb1) Sep 16 11:53:17 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. Sep 16 11:53:17 MyBookLiveDuo kernel: raid1: raid set md0 active with 2 out of 4 mirrors Sep 16 11:53:17 MyBookLiveDuo kernel: EXT3 FS on md0, internal journal Sep 16 11:53:17 MyBookLiveDuo kernel: EXT3-fs: recovery complete. Sep 16 11:53:17 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. Sep 16 11:53:17 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:0. Sep 16 11:53:25 MyBookLiveDuo kernel: md: bind<sdb3> Sep 16 11:53:25 MyBookLiveDuo kernel: md: bind<sda3> Sep 16 11:53:25 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors Sep 16 11:53:36 MyBookLiveDuo [admin-rest-api.postinst] 09/16/13 18:53:36: test context=test Sep 16 11:53:40 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k Sep 16 11:54:02 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. Sep 16 11:54:02 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. Sep 16 11:54:02 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d1790000 Jul 1 19:39:01 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:39:01 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:39:01 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:39:01 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:39:01 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:39:01 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:39:01 MyBookLiveDuo kernel: disk 2, wo:1, o:1, dev:sdb1 Jul 1 19:39:02 MyBookLiveDuo kernel: md: recovery of RAID array md0 Jul 1 19:39:02 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 19:39:40 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:39:40 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb1 Jul 1 19:39:40 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:39:40 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb1 Jul 1 19:39:40 MyBookLiveDuo kernel: disk 3, wo:1, o:1, dev:sdb2 Jul 1 19:39:41 MyBookLiveDuo kernel: md: recovery of RAID array md0 Jul 1 19:40:18 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:40:18 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:40:18 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:40:18 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb1 Jul 1 19:40:18 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sdb2 Jul 1 19:42:02 MyBookLiveDuo kernel: nfsd: last server has exited, flushing export cache Jul 1 19:42:02 MyBookLiveDuo kernel: ufsd: driver unloaded Jul 1 19:42:26 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts Jul 1 19:42:26 MyBookLiveDuo kernel: Kernel command line: root=/dev/md0 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s Jul 1 19:42:26 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) Jul 1 19:42:26 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 Jul 1 19:42:26 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 Jul 1 19:42:26 MyBookLiveDuo kernel: sda: Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:42:26 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots Jul 1 19:42:26 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 Jul 1 19:42:26 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 Jul 1 19:42:26 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk Jul 1 19:42:26 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk Jul 1 19:42:26 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect Jul 1 19:42:26 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. Jul 1 19:42:26 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! Jul 1 19:42:26 MyBookLiveDuo kernel: md: considering sdb2 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sdb2 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sdb1 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sda2 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: adding sda1 ... Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sda1> Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sda2> Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:42:26 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 19:42:26 MyBookLiveDuo kernel: md: running: <sdb2><sdb1><sda2><sda1> Jul 1 19:42:26 MyBookLiveDuo kernel: md0: WARNING: sdb2 appears to be on the same physical disk as sdb1. Jul 1 19:42:26 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. Jul 1 19:42:26 MyBookLiveDuo kernel: raid1: raid set md0 active with 4 out of 4 mirrors Jul 1 19:42:26 MyBookLiveDuo kernel: EXT3 FS on md0, internal journal Jul 1 19:42:26 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. Jul 1 19:42:26 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:0. Jul 1 19:42:32 MyBookLiveDuo kernel: md: bind<sdb3> Jul 1 19:42:32 MyBookLiveDuo kernel: md: bind<sda3> Jul 1 19:42:32 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors Jul 1 19:42:40 MyBookLiveDuo [admin-rest-api.postinst] 07/02/16 02:42:40: test context=test Jul 1 19:42:44 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k Jul 1 19:43:06 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. Jul 1 19:43:06 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. Jul 1 19:43:06 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d1790000 Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sdb1 from md0 ... Jul 1 19:44:37 MyBookLiveDuo kernel: md: cannot remove active disk sdb2 from md0 ... Jul 1 19:47:30 MyBookLiveDuo kernel: nfsd: last server has exited, flushing export cache Jul 1 19:47:31 MyBookLiveDuo kernel: ufsd: driver unloaded Jul 1 19:48:09 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts Jul 1 19:48:09 MyBookLiveDuo kernel: Kernel command line: root=/dev/md0 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s Jul 1 19:48:09 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) Jul 1 19:48:09 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 Jul 1 19:48:09 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 Jul 1 19:48:09 MyBookLiveDuo kernel: sda: Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jul 1 19:48:09 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots Jul 1 19:48:09 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 Jul 1 19:48:09 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 Jul 1 19:48:09 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk Jul 1 19:48:09 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk Jul 1 19:48:09 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect Jul 1 19:48:09 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. Jul 1 19:48:09 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! Jul 1 19:48:09 MyBookLiveDuo kernel: md: considering sdb2 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sdb2 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sdb1 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sda2 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: adding sda1 ... Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sda1> Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sda2> Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:48:09 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 19:48:09 MyBookLiveDuo kernel: md: running: <sdb2><sdb1><sda2><sda1> Jul 1 19:48:09 MyBookLiveDuo kernel: md0: WARNING: sdb2 appears to be on the same physical disk as sdb1. Jul 1 19:48:09 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. Jul 1 19:48:09 MyBookLiveDuo kernel: raid1: raid set md0 active with 4 out of 4 mirrors Jul 1 19:48:09 MyBookLiveDuo kernel: EXT3 FS on md0, internal journal Jul 1 19:48:09 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. Jul 1 19:48:09 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:0. Jul 1 19:48:13 MyBookLiveDuo kernel: md: bind<sda4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: bind<sdb4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: unbind<sdb4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: export_rdev(sdb4) Jul 1 19:48:13 MyBookLiveDuo kernel: md: unbind<sda4> Jul 1 19:48:13 MyBookLiveDuo kernel: md: export_rdev(sda4) Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sdb3> Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sda3> Jul 1 19:48:15 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sdb4> Jul 1 19:48:15 MyBookLiveDuo kernel: md: bind<sda4> Jul 1 19:53:51 MyBookLiveDuo kernel: EXT4-fs (md3): mounted filesystem with ordered data mode Jul 1 19:53:56 MyBookLiveDuo [wd-nas.postinst] 07/02/16 02:53:55: restore context=restore Jul 1 19:54:00 MyBookLiveDuo [networking-general.postinst] 07/02/16 02:54:00: restore context=restore Jul 1 19:54:01 MyBookLiveDuo [apache-php-webdav.postinst] 07/02/16 02:54:01: restore context=restore Jul 1 19:54:06 MyBookLiveDuo [date-time.postinst] 07/02/16 02:54:06: restore context=restore Jul 1 19:54:09 MyBookLiveDuo [alerts.postinst] 07/02/16 02:54:09: restore context=restore Jul 1 19:54:10 MyBookLiveDuo [admin-rest-api.postinst] 07/02/16 02:54:10: restore context=restore Jul 1 19:54:12 MyBookLiveDuo [drive-lib.postinst] 07/02/16 02:54:12: restore context=restore Jul 1 19:54:13 MyBookLiveDuo [data-volume-config.postinst] 07/02/16 02:54:13: restore context=restore Jul 1 19:54:14 MyBookLiveDuo [upnp-nas.postinst] 07/02/16 02:54:14: restore context=restore Jul 1 19:54:15 MyBookLiveDuo [dlna-server-access.postinst] 07/02/16 02:54:15: restore context=restore Jul 1 19:54:16 MyBookLiveDuo [itunes.postinst] 07/02/16 02:54:16: restore context=restore Jul 1 19:54:17 MyBookLiveDuo [nas-safepoint.postinst] 07/02/16 02:54:17: restore context=restore Jul 1 19:54:18 MyBookLiveDuo [webui.postinst] 07/02/16 02:54:18: restore context=restore Jul 1 19:54:28 MyBookLiveDuo [orion-resources.postinst] 07/02/16 02:54:28: restore context=restore Jul 1 19:54:29 MyBookLiveDuo [afp.postinst] 07/02/16 02:54:29: restore context=restore Jul 1 19:54:29 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k Jul 1 19:55:18 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:55:19 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:55:19 MyBookLiveDuo kernel: md: cannot remove active disk sdb1 from md0 ... Jul 1 19:55:19 MyBookLiveDuo kernel: md: cannot remove active disk sdb2 from md0 ... Jul 1 19:55:28 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. Jul 1 19:55:28 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. Jul 1 19:55:28 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d3b00000 Jul 1 19:55:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:55:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 2, wo:1, o:0, dev:sdb1 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sdb2 Jul 1 19:55:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 19:55:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda1 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda2 Jul 1 19:55:31 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sdb2 Jul 1 19:55:31 MyBookLiveDuo kernel: md: unbind<sdb1> Jul 1 19:55:31 MyBookLiveDuo kernel: md: export_rdev(sdb1) Jul 1 19:55:32 MyBookLiveDuo kernel: md: bind<sdb1> Jul 1 19:55:32 MyBookLiveDuo kernel: raid1: raid set md1 active with 1 out of 4 mirrors Jul 1 19:58:57 MyBookLiveDuo kernel: md: cannot remove active disk sda1 from md0 ... Jul 1 19:58:57 MyBookLiveDuo kernel: md: cannot remove active disk sda2 from md0 ... Jul 1 19:58:57 MyBookLiveDuo kernel: md: cannot remove active disk sdb2 from md0 ... Jul 1 20:00:59 MyBookLiveDuo kernel: EXT3-fs warning: checktime reached, running e2fsck is recommended Jul 1 20:00:59 MyBookLiveDuo kernel: EXT3 FS on md1, internal journal Jul 1 20:00:59 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with writeback data mode. May 7 18:23:57 MyBookLiveDuo kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts May 7 18:23:57 MyBookLiveDuo kernel: Kernel command line: root=/dev/md1 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x1 185 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x2 189 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x4 197 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: int32x8 189 MB/s May 7 18:23:57 MyBookLiveDuo kernel: raid6: using algorithm int32x4 (197 MB/s) May 7 18:23:57 MyBookLiveDuo kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de). May 7 18:23:57 MyBookLiveDuo kernel: md: raid0 personality registered for level 0 May 7 18:23:57 MyBookLiveDuo kernel: md: raid1 personality registered for level 1 May 7 18:23:57 MyBookLiveDuo kernel: md: raid10 personality registered for level 10 May 7 18:23:57 MyBookLiveDuo kernel: md: raid6 personality registered for level 6 May 7 18:23:57 MyBookLiveDuo kernel: md: raid5 personality registered for level 5 May 7 18:23:57 MyBookLiveDuo kernel: md: raid4 personality registered for level 4 May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] 4096-byte physical blocks May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write Protect is off May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] 4096-byte physical blocks May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0 May 7 18:23:57 MyBookLiveDuo kernel: sda: May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write Protect is off May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA May 7 18:23:57 MyBookLiveDuo kernel: sdb:apm82181 adma3: allocated 512 descriptor slots May 7 18:23:57 MyBookLiveDuo kernel: sda1 sda2 sda3 sda4 May 7 18:23:57 MyBookLiveDuo kernel: sdb1 sdb2 sdb3 sdb4 May 7 18:23:57 MyBookLiveDuo kernel: sd 0:0:0:0: [sda] Attached SCSI disk May 7 18:23:57 MyBookLiveDuo kernel: sd 1:0:0:0: [sdb] Attached SCSI disk May 7 18:23:57 MyBookLiveDuo kernel: md: If you don't use raid, use raid=noautodetect May 7 18:23:57 MyBookLiveDuo kernel: md: Autodetecting RAID arrays. May 7 18:23:57 MyBookLiveDuo kernel: md: sda3 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: sda4 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: sdb3 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: sdb4 does not have a valid v0.90 superblock, not importing! May 7 18:23:57 MyBookLiveDuo kernel: md: considering sdb2 ... May 7 18:23:57 MyBookLiveDuo kernel: md: adding sdb2 ... May 7 18:23:57 MyBookLiveDuo kernel: md: sdb1 has different UUID to sdb2 May 7 18:23:57 MyBookLiveDuo kernel: md: adding sda2 ... May 7 18:23:57 MyBookLiveDuo kernel: md: adding sda1 ... May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sda1> May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sda2> May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sdb2> May 7 18:23:57 MyBookLiveDuo kernel: md: running: <sdb2><sda2><sda1> May 7 18:23:57 MyBookLiveDuo kernel: md0: WARNING: sda2 appears to be on the same physical disk as sda1. May 7 18:23:57 MyBookLiveDuo kernel: raid1: raid set md0 active with 3 out of 4 mirrors May 7 18:23:57 MyBookLiveDuo kernel: md: considering sdb1 ... May 7 18:23:57 MyBookLiveDuo kernel: md: adding sdb1 ... May 7 18:23:57 MyBookLiveDuo kernel: md: bind<sdb1> May 7 18:23:57 MyBookLiveDuo kernel: md: running: <sdb1> May 7 18:23:57 MyBookLiveDuo kernel: raid1: raid set md1 active with 1 out of 4 mirrors May 7 18:23:57 MyBookLiveDuo kernel: EXT3 FS on md1, internal journal May 7 18:23:57 MyBookLiveDuo kernel: EXT3-fs: mounted filesystem with ordered data mode. May 7 18:23:57 MyBookLiveDuo kernel: VFS: Mounted root (ext3 filesystem) on device 9:1. May 7 18:24:01 MyBookLiveDuo kernel: md: bind<sdb3> May 7 18:24:01 MyBookLiveDuo kernel: md: bind<sda3> May 7 18:24:01 MyBookLiveDuo kernel: raid1: raid set md2 active with 2 out of 2 mirrors May 7 18:24:02 MyBookLiveDuo kernel: md: bind<sdb4> May 7 18:24:02 MyBookLiveDuo kernel: md: bind<sda4> May 7 18:24:02 MyBookLiveDuo kernel: EXT4-fs (md3): mounted filesystem with ordered data mode May 7 18:24:10 MyBookLiveDuo [admin-rest-api.postinst] 05/08/15 01:24:10: test context=test May 7 18:24:14 MyBookLiveDuo kernel: Adding 500544k swap on /dev/md2. Priority:-1 extents:1 across:500544k May 7 18:24:23 MyBookLiveDuo [dlna-server-access.postinst] 05/08/15 01:24:23: configure 02.00.00-100316 context=upgrade May 7 18:24:52 MyBookLiveDuo kernel: ufsd: bad vermagic: kernel tainted. May 7 18:24:52 MyBookLiveDuo kernel: ufsd: module license 'unspecified' taints kernel. May 7 18:24:52 MyBookLiveDuo kernel: ufsd: driver 8.5 (NTFS4LINUX_U85_014_S[2011-09-15-11:41:06]) LBD=ON with delayalloc with ioctl loaded at d2750000 Jul 1 20:06:48 MyBookLiveDuo kernel: md: unbind<sdb2> Jul 1 20:06:48 MyBookLiveDuo kernel: md: export_rdev(sdb2) Jul 1 20:06:48 MyBookLiveDuo kernel: md: unbind<sda2> Jul 1 20:06:48 MyBookLiveDuo kernel: md: export_rdev(sda2) Jul 1 20:06:48 MyBookLiveDuo kernel: md: unbind<sda1> Jul 1 20:06:48 MyBookLiveDuo kernel: md: export_rdev(sda1) Jul 1 20:06:50 MyBookLiveDuo kernel: md: bind<sda1> Jul 1 20:06:50 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:06:50 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:06:50 MyBookLiveDuo kernel: disk 1, wo:1, o:1, dev:sda1 Jul 1 20:06:50 MyBookLiveDuo kernel: md: recovery of RAID array md1 Jul 1 20:06:50 MyBookLiveDuo kernel: md: bind<sda2> Jul 1 20:06:50 MyBookLiveDuo kernel: md: cannot remove active disk sdb1 from md1 ... Jul 1 20:06:50 MyBookLiveDuo kernel: md: bind<sdb2> Jul 1 20:07:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:07:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:07:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:07:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 2, wo:1, o:1, dev:sdb2 Jul 1 20:07:31 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:07:31 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 2, wo:1, o:1, dev:sdb2 Jul 1 20:07:31 MyBookLiveDuo kernel: disk 3, wo:1, o:1, dev:sda2 Jul 1 20:07:31 MyBookLiveDuo kernel: md: recovery of RAID array md1 Jul 1 20:08:39 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:08:39 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sdb1 Jul 1 20:08:39 MyBookLiveDuo kernel: disk 1, wo:0, o:1, dev:sda1 Jul 1 20:08:39 MyBookLiveDuo kernel: disk 2, wo:0, o:1, dev:sdb2 Jul 1 20:08:39 MyBookLiveDuo kernel: disk 3, wo:0, o:1, dev:sda2 Jul 1 20:09:54 MyBookLiveDuo kernel: nfsd: last server has exited, flushing export cache Jul 1 20:10:49 MyBookLiveDuo kernel: md: unbind<sda4> Jul 1 20:10:49 MyBookLiveDuo kernel: md: export_rdev(sda4) Jul 1 20:10:49 MyBookLiveDuo kernel: md: unbind<sdb4> Jul 1 20:10:49 MyBookLiveDuo kernel: md: export_rdev(sdb4) Jul 1 20:10:51 MyBookLiveDuo kernel: md: bind<sda4> Jul 1 20:10:51 MyBookLiveDuo kernel: raid1: raid set md3 active with 1 out of 2 mirrors Jul 1 20:10:51 MyBookLiveDuo kernel: md: bind<sdb4> Jul 1 20:10:51 MyBookLiveDuo kernel: RAID1 conf printout: Jul 1 20:10:51 MyBookLiveDuo kernel: disk 0, wo:0, o:1, dev:sda4 Jul 1 20:10:51 MyBookLiveDuo kernel: disk 1, wo:1, o:1, dev:sdb4 Jul 1 20:10:51 MyBookLiveDuo kernel: md: recovery of RAID array md3 Jul 1 20:10:51 MyBookLiveDuo kernel: EXT4-fs (md3): mounted filesystem with ordered data mode The messages file has 1922 lines, so I am not pasting the whole content here yet, unless you suggest. 6. Trying to mount sdc4 as ext4 fails: $ sudo mount -t ext4 /dev/sdc4 p4 mount: /dev/sdc4 already mounted or p4 busy Is there a way to confirm whether sdc4 was ext4 (as r-linux) had reported, or ext3? 7. Before trying to do fsck on sdc4, I wanted to check if you had any other suggestion based on info above. Also, looks like for fsck I should be providing filesystem type. So, wanted to check if I should try ext3 or ext4 on sdc4, when trying fsck. Thanks Amit ----- Original Message ----- From: Phil Turmel <philip@turmel.org> To: Bhatia Amit <amitbhatia@rocketmail.com>; "linux-raid@vger.kernel.org" <linux-raid@vger.kernel.org> Sent: Tuesday, July 19, 2016 5:12 AM Subject: Re: Cannot start array on disk On 07/17/2016 03:59 PM, Bhatia Amit wrote: > Hi > > I have a WD Live duo setup with two 3TB drives in RAID1. After a > recent power surge etc, I could not access the enclosure data. I > removed the drives out from the enclosure and connected them via > esata cable to a Linux laptop. One of the drives had physical noise > and failed to connect at all. The other drive was able to connect and > showed up as /dev/sdc. Following some online search, I issued the > following commands to get some results, but am unable to mount the > drive to a linux laptop via esata. Questions: > > * Ideally both sdc3 and sdc4 should have shown RAID=RAID1. If sdc4 is > showing RAID=linear, is it because the other drive went totally bad, > and software decided to reconfigure this drive from RAID1 to linear > ? No way to know. I would be inclined to believe that that you didn't actually have raid1 set for those partitions. Do you recall the available space in that device while running? > * Given the one of the two drives is totally dead, is it still > possible to reconfigure, mount and recover data from the single > drive? If truly linear, no, not past the half-way mark. The device is identified as role 0, so it would be the beginning of the filesystem in a linear array. If it really was raid1 with v0.9 or v1.0 metadata, you can mount /dev/sdc4 directly to access your data. That it doesn't show a detected filesystem suggests that it wasn't raid1. Even worse, that partition shows a creation date and update date both in 2013, with no events. Suggesting that the device hasn't actually been running properly in the array since its initial creation. > * I tried scanning the drive via r-linux and it does show files > exist, but does not show any folder information. So data is there on > the drive. Is there a way to recreate the setup with just this single > drive, so that I can extract files with folder information? With v1.0 metadata, you should be able to fsck /dev/sdc4 and then mount. Kinda dangerous though -- I suggest you use an overlay for that. I suspect that sdc4 hasn't been running in your array for the past three years. > * Looking at an online "derrick" script, the script seems to call > mdadm create with the "missing" flag. Is that something I should be > doing to be able to assemble and recover data from the drive ? > "mdadm --create $rootfsRaid --verbose --metadata=0.9 --raid-devices=2 > --level=raid1 --run $diskRoot1 missing" No. Using --create is practically never the right solution, unless you've done operations that destroy the right solution. Metadata v0.9 is almost certainly wrong. If you have syslogs on your other array that show the boot details from the last successful boot *before* it died, that might provide the details needed to figure if anything recent is on sdc4. Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-20 2:52 ` Bhatia Amit @ 2016-07-20 10:30 ` Phil Turmel 2016-07-21 2:00 ` Bhatia Amit 0 siblings, 1 reply; 12+ messages in thread From: Phil Turmel @ 2016-07-20 10:30 UTC (permalink / raw) To: Bhatia Amit, linux-raid Hi Amit, { Note, convention on kernel.org is to trim & bottom post, or interleave replies with trimmed context. } On 07/19/2016 10:52 PM, Bhatia Amit wrote: > Hi Phil > > One more thing. When the enclosure became inaccesible in June 2016, > WDC gave me a new unit with drives. I dont remember for sure, but I > think I first replaced drive A from new enclosure with the Drive A > (currently in discussion) from old enclosure, hoping new unit would > reconfigure based on info from old drive. But I was not able to > access the unit. Then I put back the two new drives back in new > enclosure, configured new unit for RAID1 and then replaced the drive > A again with the drive A from old enclosure, but again no luck > accessing it (Error Message=Unable to mount). Since the default > configuration of a new configuration is Striping and not RAID1, > probably the first action (replacing drive A before configuring new > unit for RAID1), might have been the cause why this drive A shows as > RAID=linear, rather than RAID1. That could explain it, but I would have expected your mount of /dev/sdc4 to succeed. Your dmesg excerpt clearly shows a raid1 binding on partition 4, so the metadata on the drive you are examining must be wrong. The only way I know for that to happen is if there are multiple superblocks on the drive, and a plain examine is finding the v1.0 metadata first. I'm not sure if this is supported, by try specifying the version along with --examine for each of v0.90, v1.0, v1.1, and v1.2 to see if any difference shows. Paste the results from each. Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-20 10:30 ` Phil Turmel @ 2016-07-21 2:00 ` Bhatia Amit 2016-07-22 14:48 ` Phil Turmel 0 siblings, 1 reply; 12+ messages in thread From: Bhatia Amit @ 2016-07-21 2:00 UTC (permalink / raw) To: Phil Turmel, linux-raid > I'm not sure if this is supported, by try specifying the version along > with --examine for each of v0.90, v1.0, v1.1, and v1.2 to see if any > difference shows. Paste the results from each. Hi Phil Only metadata v1.0 seems to be valid for sdc4. $ sudo mdadm --examine /dev/sdc4 --metadata=0.9 mdadm: No super block found on /dev/sdc4 (Expected magic a92b4efc, got 00000000) $ $ sudo mdadm --examine /dev/sdc4 --metadata=1.0 /dev/sdc4: Magic : a92b4efc Version : 1.0 Feature Map : 0x0 Array UUID : 374e689e:3bfd050c:ab0b0dce:2d50f5fd Name : MyBookLiveDuo:3 Creation Time : Mon Sep 16 14:53:47 2013 Raid Level : linear Raid Devices : 2 Avail Dev Size : 5851500528 (2790.21 GiB 2995.97 GB) Used Dev Size : 0 Super Offset : 5851500528 sectors State : clean Device UUID : 9096f74b:0a8f2b61:93347be3:6d3b6c1b Update Time : Mon Sep 16 14:53:47 2013 Checksum : 77aa5963 - correct Events : 0 Rounding : 0K Device Role : Active device 0 Array State : AA ('A' == active, '.' == missing) $ $ sudo mdadm --examine /dev/sdc4 --metadata=1.1 mdadm: No super block found on /dev/sdc4 (Expected magic a92b4efc, got 00000000) $ $ sudo mdadm --examine /dev/sdc4 --metadata=1.2 mdadm: No super block found on /dev/sdc4 (Expected magic a92b4efc, got 00000000) $ $ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md126 : active raid1 sdc3[2] 500724 blocks super 1.0 [2/1] [_U] md127 : inactive sdc4[0](S) 2925750264 blocks super 1.0 unused devices: <none> $ $ sudo mdadm --examine --scan ARRAY /dev/md/2 metadata=1.0 UUID=7c040c5e:9c30ac6d:e534a129:20457e22 name=MyBookLiveDuo:2 ARRAY /dev/md/3 metadata=1.0 UUID=374e689e:3bfd050c:ab0b0dce:2d50f5fd name=MyBookLiveDuo:3 $ Thanks, Amit ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-21 2:00 ` Bhatia Amit @ 2016-07-22 14:48 ` Phil Turmel 2016-07-23 4:00 ` Bhatia Amit 0 siblings, 1 reply; 12+ messages in thread From: Phil Turmel @ 2016-07-22 14:48 UTC (permalink / raw) To: Bhatia Amit, linux-raid On 07/20/2016 10:00 PM, Bhatia Amit wrote: > > >> I'm not sure if this is supported, by try specifying the version along >> with --examine for each of v0.90, v1.0, v1.1, and v1.2 to see if any >> difference shows. Paste the results from each. > > > Hi Phil > > Only metadata v1.0 seems to be valid for sdc4. Hmm. I'm stumped. The only thing left that I'd try is to hexdump search the partition looking for an ext4 magic signature. That would give us a clue. { Fair warning: this doesn't often end well. } To find possible ext4 signatures, use this: hexdump -C /dev/sdc4 |egrep '^[0-9a-f]+30 .+ 53 ef' >sb.lst Not all of them will be superblocks, of course, but that will give addresses that can be more closely examined. Paste the first hundred or so matches in your reply. Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-22 14:48 ` Phil Turmel @ 2016-07-23 4:00 ` Bhatia Amit 2016-07-23 20:50 ` Phil Turmel 0 siblings, 1 reply; 12+ messages in thread From: Bhatia Amit @ 2016-07-23 4:00 UTC (permalink / raw) To: Phil Turmel, linux-raid > Hmm. I'm stumped. The only thing left that I'd try is to hexdump > search the partition looking for an ext4 magic signature. That would > give us a clue. > > { Fair warning: this doesn't often end well. } > > To find possible ext4 signatures, use this: > > hexdump -C /dev/sdc4 |egrep '^[0-9a-f]+30 .+ 53 ef' >sb.lst > > Not all of them will be superblocks, of course, but that will give > addresses that can be more closely examined. Paste the first hundred or > so matches in your reply. Hi Phil, Following is the output from hexdump command you suggested above. Additionally, the r-linux tool that I had used to scan the disk for files, had claimed to find superblocks at multiple locations on disk. So, after the hexdump output, I have also dumped some information from hex output of the claimed superblock region, from three locations (first, middle and last superblock) on disk. Also, each superblock is claimed to occupy 2 sectors, but I have only pasted the first sector here, because the second sector is all zeros. The first two superblocks look to be exactly the same, but the last one seems a little different. Thanks, Amit $ sudo hexdump -C /dev/sdc4 |egrep '^[0-9a-f]+30 .+ 53 ef' >sb.lst ^C $ cat sb.lst 105bf330 c7 c2 ed 89 e6 42 12 cf 53 ef 9a 71 0b b5 90 48 |.....B..S..q...H| 10f66530 98 d5 99 9c fa f1 f2 22 53 ef 42 bb db 27 7d 71 |......."S.B..'}q| 110ec130 b8 39 a0 79 5a 1c 62 c8 53 ef b1 e4 46 a4 91 07 |.9.yZ.b.S...F...| 127ab030 e4 74 55 04 d1 e1 82 0d 53 ef f4 d6 cf 70 a1 86 |.tU.....S....p..| 132fb230 11 e6 63 f9 19 5b 1d d4 53 ef a1 8e c1 6f 57 48 |..c..[..S....oWH| 13ad2d30 eb 4c 2e 55 6b 97 74 41 53 ef 46 44 0d 63 d9 7e |.L.Uk.tAS.FD.c.~| 15c01f30 d4 1e 67 0c 30 40 a4 c6 53 ef 4e e8 36 f4 e9 bd |..g.0@..S.N.6...| 15de7730 4c fa 94 59 e5 bd b6 b2 53 ef f4 0f c7 78 78 0e |L..Y....S....xx.| 16ecd230 75 3d a7 28 81 0a c6 73 53 ef 96 2a d7 10 ae cc |u=.(...sS..*....| 18307f30 40 a5 5f 2a ec 1c 56 d0 53 ef 28 d7 d9 8d b4 f4 |@._*..V.S.(.....| 187eab30 f7 1b 1e e5 5e 83 28 37 53 ef b7 b4 42 13 c1 0c |....^.(7S...B...| 192f3030 e7 73 5a 17 5e 11 21 a5 53 ef 05 8f bd 5d 2d 92 |.sZ.^.!.S....]-.| 1d28de30 32 33 bd 1c b7 10 e6 78 53 ef 88 a5 9b 88 b6 50 |23.....xS......P| 2129fe30 1b 0e 6d 27 46 04 da 81 53 ef 58 14 15 09 58 45 |..m'F...S.X...XE| 2326d730 7f fc 78 d3 55 d6 12 ac 53 ef 73 67 80 15 15 70 |..x.U...S.sg...p| 23b56d30 4f 9c 76 9c e8 17 86 a3 53 ef 78 1b 58 e2 e2 47 |O.v.....S.x.X..G| 2624bd30 ad 07 ec 2d e8 db 0a 30 53 ef 65 c0 90 11 3e 1b |...-...0S.e...>.| 26afc630 fd 35 c8 6d fc f1 13 17 53 ef 61 44 7e 1b d2 ca |.5.m....S.aD~...| 27db4b30 02 d8 79 1e 76 7c 93 14 53 ef 9a f8 77 62 0a 7e |..y.v|..S...wb.~| 27dece30 a3 8f 27 a4 c2 f4 96 3a 53 ef 3a 3a 71 df 44 e8 |..'....:S.::q.D.| 2a925930 fa f1 c4 dd 01 77 d0 34 53 ef 40 71 42 e0 75 0c |.....w.4S.@qB.u.| 2c3cec30 92 76 09 be ad c8 47 86 53 ef 72 16 57 4d 81 cb |.v....G.S.r.WM..| 2c400f30 24 cb 98 10 3c d0 f3 d5 53 ef 53 d4 b3 e1 63 e6 |$...<...S.S...c.| 2cdc8c30 16 81 f1 14 36 ec d6 cc 53 ef 73 64 f5 ea 5d 5d |....6...S.sd..]]| 2d6f1630 f0 bf e7 bb 29 ad f2 0d 53 ef ba 32 a0 68 84 74 |....)...S..2.h.t| 2e9c2330 db e8 f5 ed f5 12 26 f6 53 ef f3 d6 61 c0 26 e3 |......&.S...a.&.| 2faf0830 9c 68 d2 d1 f7 fa 15 0d 53 ef 63 21 da d1 0e 8b |.h......S.c!....| 32f30930 35 23 2d 12 64 67 2c 54 53 ef d8 fa 36 2c 95 f2 |5#-.dg,TS...6,..| f90ba830 91 88 98 6e f4 19 e1 c4 53 ef a9 fc b1 52 b1 97 |...n....S....R..| f91c6530 bc 30 41 c1 8c 1b 8c a8 53 ef 94 a9 9b f0 8e 56 |.0A.....S......V| fa245930 a4 66 34 9c 70 bc 44 70 53 ef 32 d5 46 fa 3c aa |.f4.p.DpS.2.F.<.| fb143c30 b1 13 45 db d6 19 00 ec 53 ef fd 49 a5 7f b0 e8 |..E.....S..I....| fc20f030 33 e1 02 bf cc ee 1f 93 53 ef 2b 4a ff 3e fc e3 |3.......S.+J.>..| fcd6be30 3f 36 8c bf 11 8e 17 c3 53 ef 49 86 15 22 27 c6 |?6......S.I.."'.| fd436f30 98 5c cc 71 7a 12 6f 15 53 ef f2 67 06 68 80 e9 |.\.qz.o.S..g.h..| ff5b6830 fd 41 f4 49 7b 59 52 1f 53 ef 59 05 57 56 7d 89 |.A.I{YR.S.Y.WV}.| fff80030 47 9d ba 50 03 00 1b 00 53 ef 00 00 01 00 00 00 |G..P....S.......| 1003e5030 a3 70 2a c3 b7 ff 00 a8 53 ef ff 00 e0 93 fe 2f |.p*.....S....../| 1020cdf30 b9 46 dc 14 4d c7 cc 38 53 ef 4a 0c 99 a1 cd a6 |.F..M..8S.J.....| 10629e830 19 0c 14 0e b9 ab 5f f0 53 ef 83 1e 1c f1 47 c1 |......_.S.....G.| 10801e530 81 d7 38 e9 83 5f 3b 53 53 ef b3 fa ee 8d 75 a9 |..8.._;SS.....u.| 109421e30 a9 92 47 01 f3 df 24 fa 53 ef 6c 25 7b 43 18 e1 |..G...$.S.l%{C..| 109440b30 f8 fe d1 a4 08 21 79 09 53 ef ed 4e 90 32 0d 82 |.....!y.S..N.2..| 10bc21830 0d c4 cf e6 80 36 b6 3e 53 ef de a3 82 db 73 99 |.....6.>S.....s.| 10c4bef30 8c 46 79 e3 8e 95 c1 5b 53 ef f0 0f df b1 62 29 |.Fy....[S.....b)| 10e0edd30 0d 70 ad 87 da e0 9e 7a 53 ef a4 95 67 48 dd 63 |.p.....zS...gH.c| 111dfc630 dd 2e 72 ce 16 59 24 8d 53 ef 7f c0 eb f4 0a d5 |..r..Y$.S.......| 1131ea130 b2 8d 82 ec b9 56 db bd 53 ef 2f bf a5 29 b6 45 |.....V..S./..).E| 1133f4e30 e1 8e 42 0e 82 be 56 0b 53 ef 65 ac ae 67 5c 59 |..B...V.S.e..g\Y| 11401ff30 49 36 31 43 b4 f5 53 d4 53 ef 25 fb 3d a1 11 31 |I61C..S.S.%.=..1| 1145c1530 a0 86 2f 29 db 6e d6 cf 53 ef 4b 9d 91 b3 cc 4a |../).n..S.K....J| 1146b0930 6d e2 6b 58 91 a6 58 6e 53 ef 44 4f de af 33 37 |m.kX..XnS.DO..37| 114a2b430 89 21 93 70 45 0b 8f 4c 53 ef 35 0b 6d 32 ca 5b |.!.pE..LS.5.m2.[| 115032330 66 45 5d 92 65 19 93 f9 53 ef 95 e2 b6 1e 46 d5 |fE].e...S.....F.| 115205730 7e 64 6e 08 dd f2 ed 01 53 ef d4 73 25 2d 49 9f |~dn.....S..s%-I.| 1165ed030 39 00 1a 69 2c d2 3c db 53 ef 60 00 6b f2 28 3b |9..i,.<.S.`.k.(;| 1185acd30 d1 98 5b f7 6a 0e 13 6f 53 ef 51 6a 06 37 75 8c |..[.j..oS.Qj.7u.| 11984b230 18 f4 ab 40 fa 55 90 5e 53 ef 57 c1 ad 0c cb e0 |...@.U.^S.W.....| 11c077930 00 d7 af 14 c0 1c 93 cf 53 ef 5d b0 89 9c e5 76 |........S.]....v| 11c38ff30 33 cf 3c c5 c9 f9 87 e7 53 ef 5c f5 14 00 f0 e3 |3.<.....S.\.....| 11db89230 61 c0 1f 9f a8 e6 ff 00 53 ef 5d 7a 83 ac a8 6c |a.......S.]z...l| 11e947c30 e6 6d e0 55 51 d6 cb 9c 53 ef 98 0f 55 6e fe b8 |.m.UQ...S...Un..| 11eadce30 8b 7d 71 7c 1c 0f ad c1 53 ef a0 1d 65 66 fa 06 |.}q|....S...ef..| 11f485430 5e 2f 5a 2b 48 69 62 44 53 ef 65 d5 06 a0 29 a2 |^/Z+HibDS.e...).| 11fc23030 a9 97 1f b7 75 ef f6 45 53 ef f6 f5 59 d2 4f 25 |....u..ES...Y.O%| 1248a2b30 63 b9 43 b5 5d 4e e8 47 53 ef ed 4b e6 06 52 e0 |c.C.]N.GS..K..R.| 127ad8830 a5 9c 2a 44 50 2f f0 0f 53 ef cf eb 57 46 37 d4 |..*DP/..S...WF7.| 129bc9630 04 04 01 01 01 01 04 02 53 ef 2f 57 69 6e 64 6f |........S./Windo| 12a04da30 4e 68 f3 63 2a ab 18 d8 53 ef 7b d6 36 be c5 a6 |Nh.c*...S.{.6...| 12b8a2b30 59 ab c2 61 49 da 68 2b 53 ef 8b 13 03 e5 f7 02 |Y..aI.h+S.......| 12d963530 92 cd 5e 5f 0d 56 8e 4b 53 ef a7 13 b2 64 a0 d2 |..^_.V.KS....d..| 12dba1330 ff df 64 ae f0 b0 b6 f7 53 ef 97 06 ff 92 9b 82 |..d.....S.......| 12de94f30 88 85 59 bb 88 5f 50 58 53 ef 18 af 98 14 c1 62 |..Y.._PXS......b| 12e2d6930 d0 26 8c 44 8a 91 9e 2e 53 ef 9b 1e f8 af a6 70 |.&.D....S......p| 12f111030 23 df 68 37 78 f3 ad bb 53 ef 73 61 37 81 56 54 |#.h7x...S.sa7.VT| 12f4f4430 40 ba 7d 05 40 3d f0 82 53 ef 21 a8 f3 a8 bc 7d |@.}.@=..S.!....}| 12fd32030 fa 67 9f b2 bc 4c 6d b0 53 ef 05 62 62 32 93 81 |.g...Lm.S..bb2..| 130852230 e9 fa c8 0c af 14 93 bd 53 ef 33 ee 09 61 1e 6b |........S.3..a.k| 1323fd330 7d 4e cb 58 78 ca 8d e1 53 ef 12 f6 ee 19 68 46 |}N.Xx...S.....hF| 132ae3b30 50 35 42 46 d9 bf af a0 53 ef 6c dd 82 8b c4 ce |P5BF....S.l.....| 132c99830 38 69 aa 62 1d ce 64 7b 53 ef 77 fe 80 59 f4 35 |8i.b..d{S.w..Y.5| 133d49730 1a 48 8a 29 f6 1a 68 c8 53 ef 65 17 6f 78 9d f7 |.H.)..h.S.e.ox..| 1345ed230 01 71 89 16 36 c4 b0 26 53 ef 66 9f 02 f6 39 1b |.q..6..&S.f...9.| 13490ec30 95 03 fb 23 62 06 9b 5b 53 ef 1c 9a 24 6e 2b c3 |...#b..[S...$n+.| 135bc7930 c8 4d 9d 4e 5e 24 9a 33 53 ef b7 4f 56 6c 9f c7 |.M.N^$.3S..OVl..| 13efd6e30 09 03 03 03 02 99 42 19 53 ef 09 03 03 03 02 99 |......B.S.......| 1433a1630 19 bb 0a 03 04 03 54 83 53 ef 1d 19 bc 0a 03 04 |......T.S.......| 1529e6f30 12 0f bc 17 8f 9f 1a 48 53 ef 5c 2b b1 1f df 73 |.......HS.\+...s| 157810530 65 49 0b 1d 4a 68 08 00 53 ef 8f e3 37 97 7d 78 |eI..Jh..S...7.}x| 157a38730 7f c0 98 96 b4 cf ea 3a 53 ef 59 c8 e0 72 d7 c4 |.......:S.Y..r..| 15a696530 41 ab e4 ce 11 c6 14 9e 53 ef b9 7b 0d c7 23 ee |A.......S..{..#.| 15b0bb230 71 e4 7f 75 89 9f 49 5c 53 ef bf e5 84 21 7b a9 |q..u..I\S....!{.| 15b3cfc30 d3 a3 15 81 14 01 89 a0 53 ef e4 0c c1 9b e0 09 |........S.......| 15e5c2e30 51 0c d3 53 dd 7f 5b e7 53 ef 7b 4e fe d0 9c 39 |Q..S..[.S.{N...9| 15f417c30 66 b6 00 ca ca 90 2d ae 53 ef 47 aa eb 68 18 30 |f.....-.S.G..h.0| 1611a6530 ad e5 c0 08 7e 9f 1f 02 53 ef d6 d5 f3 df 6e f6 |....~...S.....n.| 167671330 6c 00 2c 17 f7 94 11 00 53 ef d3 61 00 28 16 47 |l.,.....S..a.(.G| 168ad2730 9f 7a 9a 77 da 7f a9 bf 53 ef 9d 74 be b5 36 ef |.z.w....S..t..6.| 1696ba630 e2 e9 32 48 30 b8 c9 4b 53 ef 8b 58 2e 9d 24 09 |..2H0..KS..X..$.| 16b326930 5f 01 e6 7c 20 c9 39 be 53 ef 69 08 f5 d1 ee 86 |_..| .9.S.i.....| 16b431830 40 64 66 38 0c 06 15 ba 53 ef de bd d3 ee fb 7e |@df8....S......~| 1706ca530 3a e1 b9 b2 e1 4d d4 00 53 ef f0 45 c8 4e ce 33 |:....M..S..E.N.3| 170cd5230 c6 7e dd 7d a0 21 80 2d 53 ef 9d b1 09 d4 ea aa |.~.}.!. $ cat sblock.txt Name: Ext2/Ext3/Ext4 SuperBlock Offset (in sectors): 8387584 Size (in sectors): 2 Sector 8387584 (Parent: WDC WD30EZRX-00D8PB0 80.00A80 Record: 17419264) FFF80000: 00 46 B7 02 5F 8C B9 02 - 00 00 00 00 62 25 B6 02 .F.._.......b%.. FFF80010: 1A 3B B7 02 00 00 00 00 - 06 00 00 00 06 00 00 00 .;.............. FFF80020: F8 FF 00 00 F8 FF 00 00 - 00 FF 00 00 43 3E B3 4F ............C>.O FFF80030: 47 9D BA 50 03 00 1B 00 - 53 EF 00 00 01 00 00 00 G..P....S....... FFF80040: 3B B5 02 00 00 4E ED 00 - 00 00 00 00 01 00 00 00 ;....N.......... FFF80050: 00 00 00 00 0B 00 00 00 - 00 01 01 00 3C 00 00 00 ............<... FFF80060: 42 02 00 00 7B 00 00 00 - B6 7F 9F FD 12 BF 4D 57 B...{.........MW FFF80070: A8 34 DD 09 E9 E8 BA C0 - 00 00 00 00 00 00 00 00 .4.............. FFF80080: 00 00 00 00 00 00 00 00 - 2F 43 61 63 68 65 56 6F ......../CacheVo FFF80090: 6C 75 6D 65 00 C8 24 9E - 20 22 82 24 22 C8 1B 60 lume..$. ".$"..` FFF800A0: 60 FF FF FF 9C CA D0 E4 - 5C C8 13 41 80 C0 10 E6 `.......\..A.... FFF800B0: 68 C8 08 21 60 CA D0 E4 - 5C 00 00 00 00 CD AC 46 h..!`...\......F FFF800C0: 80 C8 1C 5A 60 C8 24 9E - 00 00 00 00 00 00 20 00 ...Z`.$....... . FFF800D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF800E0: 08 00 00 00 00 00 00 00 - 00 00 00 00 FC ED 10 2F .............../ FFF800F0: 38 44 66 85 D0 AC 7C A3 - FF F3 B0 AF 01 01 00 00 8Df...|......... FFF80100: 00 00 00 00 00 00 00 00 - 3B B5 02 00 0A F3 02 00 ........;....... FFF80110: 04 00 00 00 00 00 00 00 - 00 00 00 00 FF 7F 00 00 ................ FFF80120: 78 EA B0 02 FF 7F 00 00 - 01 00 00 00 77 6A B1 02 x...........wj.. FFF80130: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF80140: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 80 ................ FFF80150: 00 00 00 00 00 00 00 00 - 00 00 00 00 1C 00 1C 00 ................ FFF80160: 02 00 00 00 FF 78 00 00 - 00 00 00 00 00 00 00 00 .....x.......... FFF80170: 00 00 00 00 04 00 00 00 - 94 F3 87 01 00 00 00 00 ................ FFF80180: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF80190: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF801A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF801B0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF801C0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF801D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF801E0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ FFF801F0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ Name: Ext2/Ext3/Ext4 SuperBlock Offset (in sectors): 2038182912 Size (in sectors): 2 Sector 2038182912 (Parent: WDC WD30EZRX-00D8PB0 80.00A80 Record: 2047214592) F2F8680000: 00 46 B7 02 5F 8C B9 02 - 00 00 00 00 62 25 B6 02 .F.._.......b%.. F2F8680010: 1A 3B B7 02 00 00 00 00 - 06 00 00 00 06 00 00 00 .;.............. F2F8680020: F8 FF 00 00 F8 FF 00 00 - 00 FF 00 00 43 3E B3 4F ............C>.O F2F8680030: 47 9D BA 50 03 00 1B 00 - 53 EF 00 00 01 00 00 00 G..P....S....... F2F8680040: 3B B5 02 00 00 4E ED 00 - 00 00 00 00 01 00 00 00 ;....N.......... F2F8680050: 00 00 00 00 0B 00 00 00 - 00 01 F3 00 3C 00 00 00 ............<... F2F8680060: 42 02 00 00 7B 00 00 00 - B6 7F 9F FD 12 BF 4D 57 B...{.........MW F2F8680070: A8 34 DD 09 E9 E8 BA C0 - 00 00 00 00 00 00 00 00 .4.............. F2F8680080: 00 00 00 00 00 00 00 00 - 2F 43 61 63 68 65 56 6F ......../CacheVo F2F8680090: 6C 75 6D 65 00 C8 24 9E - 20 22 82 24 22 C8 1B 60 lume..$. ".$"..` F2F86800A0: 60 FF FF FF 9C CA D0 E4 - 5C C8 13 41 80 C0 10 E6 `.......\..A.... F2F86800B0: 68 C8 08 21 60 CA D0 E4 - 5C 00 00 00 00 CD AC 46 h..!`...\......F F2F86800C0: 80 C8 1C 5A 60 C8 24 9E - 00 00 00 00 00 00 20 00 ...Z`.$....... . F2F86800D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86800E0: 08 00 00 00 00 00 00 00 - 00 00 00 00 FC ED 10 2F .............../ F2F86800F0: 38 44 66 85 D0 AC 7C A3 - FF F3 B0 AF 01 01 00 00 8Df...|......... F2F8680100: 00 00 00 00 00 00 00 00 - 3B B5 02 00 0A F3 02 00 ........;....... F2F8680110: 04 00 00 00 00 00 00 00 - 00 00 00 00 FF 7F 00 00 ................ F2F8680120: 78 EA B0 02 FF 7F 00 00 - 01 00 00 00 77 6A B1 02 x...........wj.. F2F8680130: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F8680140: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 80 ................ F2F8680150: 00 00 00 00 00 00 00 00 - 00 00 00 00 1C 00 1C 00 ................ F2F8680160: 02 00 00 00 FF 78 00 00 - 00 00 00 00 00 00 00 00 .....x.......... F2F8680170: 00 00 00 00 04 00 00 00 - 94 F3 87 01 00 00 00 00 ................ F2F8680180: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F8680190: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86801A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86801B0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86801C0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86801D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86801E0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ F2F86801F0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ Name: Ext2/Ext3/Ext4 SuperBlock Offset (in sectors): 5781334786 Size (in sectors): 2 Sector 5781334786 (Parent: WDC WD30EZRX-00D8PB0 80.00A80 Record: 5790366466) 2B130560400: 00 46 B7 02 5F 8C B9 02 - 00 00 00 00 25 7F 09 02 .F.._.......%... 2B130560410: DC F8 99 02 00 00 00 00 - 06 00 00 00 06 00 00 00 ................ 2B130560420: F8 FF 00 00 F8 FF 00 00 - 00 FF 00 00 6D C8 02 57 ............m..W 2B130560430: 6D C8 02 57 2E 00 1B 00 - 53 EF 01 00 01 00 00 00 m..W....S....... 2B130560440: 3B B5 02 00 00 4E ED 00 - 00 00 00 00 01 00 00 00 ;....N.......... 2B130560450: 00 00 00 00 0B 00 00 00 - 00 01 00 00 3C 00 00 00 ............<... 2B130560460: 46 02 00 00 7B 00 00 00 - B6 7F 9F FD 12 BF 4D 57 F...{.........MW 2B130560470: A8 34 DD 09 E9 E8 BA C0 - 00 00 00 00 00 00 00 00 .4.............. 2B130560480: 00 00 00 00 00 00 00 00 - 2F 43 61 63 68 65 56 6F ......../CacheVo 2B130560490: 6C 75 6D 65 00 C7 4B BE - 20 24 82 24 82 C8 1B A0 lume..K. $.$.... 2B1305604A0: 60 FF FF FF 9C C0 F1 11 - DC C8 13 2A A0 C0 10 E6 `..........*.... 2B1305604B0: 68 C8 08 21 60 C0 F1 11 - DC 00 00 00 00 CF 3D 2A h..!`.........=* 2B1305604C0: E0 C2 94 C1 60 C7 4B BE - 00 00 00 00 00 00 20 00 ....`.K....... . 2B1305604D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305604E0: 08 00 00 00 00 00 00 00 - 00 00 00 00 FC ED 10 2F .............../ 2B1305604F0: 38 44 66 85 D0 AC 7C A3 - FF F3 B0 AF 01 01 00 00 8Df...|......... 2B130560500: 00 00 00 00 00 00 00 00 - 3B B5 02 00 0A F3 02 00 ........;....... 2B130560510: 04 00 00 00 00 00 00 00 - 00 00 00 00 FF 7F 00 00 ................ 2B130560520: 78 EA B0 02 FF 7F 00 00 - 01 00 00 00 77 6A B1 02 x...........wj.. 2B130560530: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B130560540: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 80 ................ 2B130560550: 00 00 00 00 00 00 00 00 - 00 00 00 00 1C 00 1C 00 ................ 2B130560560: 02 00 00 00 FF 78 00 00 - 00 00 00 00 00 00 00 00 .....x.......... 2B130560570: 00 00 00 00 04 00 00 00 - D4 DD EB 54 00 00 00 00 ...........T.... 2B130560580: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B130560590: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305605A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305605B0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305605C0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305605D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305605E0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 2B1305605F0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-23 4:00 ` Bhatia Amit @ 2016-07-23 20:50 ` Phil Turmel 2016-07-23 22:21 ` Bhatia Amit 0 siblings, 1 reply; 12+ messages in thread From: Phil Turmel @ 2016-07-23 20:50 UTC (permalink / raw) To: Bhatia Amit, linux-raid Hi Amit, You're not going like this news: On 07/23/2016 12:00 AM, Bhatia Amit wrote: > Following is the output from hexdump command you suggested above. Additionally, the r-linux tool that I had used to scan the disk for files, had claimed to find superblocks at multiple locations on disk. So, after the hexdump output, I have also dumped some information from hex output of the claimed superblock region, from three locations (first, middle and last superblock) on disk. Also, each superblock is claimed to occupy 2 sectors, but I have only pasted the first sector here, because the second sector is all zeros. The first two superblocks look to be exactly the same, but the last one seems a little different. > fff80030 47 9d ba 50 03 00 1b 00 53 ef 00 00 01 00 00 00 |G..P....S.......| > $ cat sblock.txt > > Name: Ext2/Ext3/Ext4 SuperBlock > Offset (in sectors): 8387584 > Size (in sectors): 2 > > > Sector 8387584 (Parent: WDC WD30EZRX-00D8PB0 80.00A80 Record: 17419264) > > FFF80000: 00 46 B7 02 5F 8C B9 02 - 00 00 00 00 62 25 B6 02 .F.._.......b%.. > FFF80010: 1A 3B B7 02 00 00 00 00 - 06 00 00 00 06 00 00 00 .;.............. > FFF80020: F8 FF 00 00 F8 FF 00 00 - 00 FF 00 00 43 3E B3 4F ............C>.O > FFF80030: 47 9D BA 50 03 00 1B 00 - 53 EF 00 00 01 00 00 00 G..P....S....... > FFF80040: 3B B5 02 00 00 4E ED 00 - 00 00 00 00 01 00 00 00 ;....N.......... > FFF80050: 00 00 00 00 0B 00 00 00 - 00 01 01 00 3C 00 00 00 ............<... > FFF80060: 42 02 00 00 7B 00 00 00 - B6 7F 9F FD 12 BF 4D 57 B...{.........MW > FFF80070: A8 34 DD 09 E9 E8 BA C0 - 00 00 00 00 00 00 00 00 .4.............. > FFF80080: 00 00 00 00 00 00 00 00 - 2F 43 61 63 68 65 56 6F ......../CacheVo > FFF80090: 6C 75 6D 65 00 C8 24 9E - 20 22 82 24 22 C8 1B 60 lume..$. ".$"..` > FFF800A0: 60 FF FF FF 9C CA D0 E4 - 5C C8 13 41 80 C0 10 E6 `.......\..A.... > FFF800B0: 68 C8 08 21 60 CA D0 E4 - 5C 00 00 00 00 CD AC 46 h..!`...\......F > FFF800C0: 80 C8 1C 5A 60 C8 24 9E - 00 00 00 00 00 00 20 00 ...Z`.$....... . > FFF800D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF800E0: 08 00 00 00 00 00 00 00 - 00 00 00 00 FC ED 10 2F .............../ > FFF800F0: 38 44 66 85 D0 AC 7C A3 - FF F3 B0 AF 01 01 00 00 8Df...|......... > FFF80100: 00 00 00 00 00 00 00 00 - 3B B5 02 00 0A F3 02 00 ........;....... > FFF80110: 04 00 00 00 00 00 00 00 - 00 00 00 00 FF 7F 00 00 ................ > FFF80120: 78 EA B0 02 FF 7F 00 00 - 01 00 00 00 77 6A B1 02 x...........wj.. > FFF80130: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF80140: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 80 ................ > FFF80150: 00 00 00 00 00 00 00 00 - 00 00 00 00 1C 00 1C 00 ................ > FFF80160: 02 00 00 00 FF 78 00 00 - 00 00 00 00 00 00 00 00 .....x.......... > FFF80170: 00 00 00 00 04 00 00 00 - 94 F3 87 01 00 00 00 00 ................ > FFF80180: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF80190: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF801A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF801B0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF801C0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF801D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF801E0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > FFF801F0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > > > > Name: Ext2/Ext3/Ext4 SuperBlock > Offset (in sectors): 2038182912 > Size (in sectors): 2 > > > Sector 2038182912 (Parent: WDC WD30EZRX-00D8PB0 80.00A80 Record: 2047214592) > > > F2F8680000: 00 46 B7 02 5F 8C B9 02 - 00 00 00 00 62 25 B6 02 .F.._.......b%.. > F2F8680010: 1A 3B B7 02 00 00 00 00 - 06 00 00 00 06 00 00 00 .;.............. > F2F8680020: F8 FF 00 00 F8 FF 00 00 - 00 FF 00 00 43 3E B3 4F ............C>.O > F2F8680030: 47 9D BA 50 03 00 1B 00 - 53 EF 00 00 01 00 00 00 G..P....S....... > F2F8680040: 3B B5 02 00 00 4E ED 00 - 00 00 00 00 01 00 00 00 ;....N.......... > F2F8680050: 00 00 00 00 0B 00 00 00 - 00 01 F3 00 3C 00 00 00 ............<... > F2F8680060: 42 02 00 00 7B 00 00 00 - B6 7F 9F FD 12 BF 4D 57 B...{.........MW > F2F8680070: A8 34 DD 09 E9 E8 BA C0 - 00 00 00 00 00 00 00 00 .4.............. > F2F8680080: 00 00 00 00 00 00 00 00 - 2F 43 61 63 68 65 56 6F ......../CacheVo > F2F8680090: 6C 75 6D 65 00 C8 24 9E - 20 22 82 24 22 C8 1B 60 lume..$. ".$"..` > F2F86800A0: 60 FF FF FF 9C CA D0 E4 - 5C C8 13 41 80 C0 10 E6 `.......\..A.... > F2F86800B0: 68 C8 08 21 60 CA D0 E4 - 5C 00 00 00 00 CD AC 46 h..!`...\......F > F2F86800C0: 80 C8 1C 5A 60 C8 24 9E - 00 00 00 00 00 00 20 00 ...Z`.$....... . > F2F86800D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86800E0: 08 00 00 00 00 00 00 00 - 00 00 00 00 FC ED 10 2F .............../ > F2F86800F0: 38 44 66 85 D0 AC 7C A3 - FF F3 B0 AF 01 01 00 00 8Df...|......... > F2F8680100: 00 00 00 00 00 00 00 00 - 3B B5 02 00 0A F3 02 00 ........;....... > F2F8680110: 04 00 00 00 00 00 00 00 - 00 00 00 00 FF 7F 00 00 ................ > F2F8680120: 78 EA B0 02 FF 7F 00 00 - 01 00 00 00 77 6A B1 02 x...........wj.. > F2F8680130: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F8680140: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 80 ................ > F2F8680150: 00 00 00 00 00 00 00 00 - 00 00 00 00 1C 00 1C 00 ................ > F2F8680160: 02 00 00 00 FF 78 00 00 - 00 00 00 00 00 00 00 00 .....x.......... > F2F8680170: 00 00 00 00 04 00 00 00 - 94 F3 87 01 00 00 00 00 ................ > F2F8680180: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F8680190: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86801A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86801B0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86801C0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86801D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86801E0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > F2F86801F0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ These two superblocks above have a write timestamp of Sat Dec 01 19:13:59 EST 2012. Little endian "47 9D BA 50". See https://ext4.wiki.kernel.org/index.php/Ext4_Disk_Layout#The_Super_Block > Name: Ext2/Ext3/Ext4 SuperBlock > Offset (in sectors): 5781334786 > Size (in sectors): 2 > > > > Sector 5781334786 (Parent: WDC WD30EZRX-00D8PB0 80.00A80 Record: 5790366466) > > > 2B130560400: 00 46 B7 02 5F 8C B9 02 - 00 00 00 00 25 7F 09 02 .F.._.......%... > 2B130560410: DC F8 99 02 00 00 00 00 - 06 00 00 00 06 00 00 00 ................ > 2B130560420: F8 FF 00 00 F8 FF 00 00 - 00 FF 00 00 6D C8 02 57 ............m..W > 2B130560430: 6D C8 02 57 2E 00 1B 00 - 53 EF 01 00 01 00 00 00 m..W....S....... > 2B130560440: 3B B5 02 00 00 4E ED 00 - 00 00 00 00 01 00 00 00 ;....N.......... > 2B130560450: 00 00 00 00 0B 00 00 00 - 00 01 00 00 3C 00 00 00 ............<... > 2B130560460: 46 02 00 00 7B 00 00 00 - B6 7F 9F FD 12 BF 4D 57 F...{.........MW > 2B130560470: A8 34 DD 09 E9 E8 BA C0 - 00 00 00 00 00 00 00 00 .4.............. > 2B130560480: 00 00 00 00 00 00 00 00 - 2F 43 61 63 68 65 56 6F ......../CacheVo > 2B130560490: 6C 75 6D 65 00 C7 4B BE - 20 24 82 24 82 C8 1B A0 lume..K. $.$.... > 2B1305604A0: 60 FF FF FF 9C C0 F1 11 - DC C8 13 2A A0 C0 10 E6 `..........*.... > 2B1305604B0: 68 C8 08 21 60 C0 F1 11 - DC 00 00 00 00 CF 3D 2A h..!`.........=* > 2B1305604C0: E0 C2 94 C1 60 C7 4B BE - 00 00 00 00 00 00 20 00 ....`.K....... . > 2B1305604D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305604E0: 08 00 00 00 00 00 00 00 - 00 00 00 00 FC ED 10 2F .............../ > 2B1305604F0: 38 44 66 85 D0 AC 7C A3 - FF F3 B0 AF 01 01 00 00 8Df...|......... > 2B130560500: 00 00 00 00 00 00 00 00 - 3B B5 02 00 0A F3 02 00 ........;....... > 2B130560510: 04 00 00 00 00 00 00 00 - 00 00 00 00 FF 7F 00 00 ................ > 2B130560520: 78 EA B0 02 FF 7F 00 00 - 01 00 00 00 77 6A B1 02 x...........wj.. > 2B130560530: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B130560540: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 80 ................ > 2B130560550: 00 00 00 00 00 00 00 00 - 00 00 00 00 1C 00 1C 00 ................ > 2B130560560: 02 00 00 00 FF 78 00 00 - 00 00 00 00 00 00 00 00 .....x.......... > 2B130560570: 00 00 00 00 04 00 00 00 - D4 DD EB 54 00 00 00 00 ...........T.... > 2B130560580: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B130560590: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305605A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305605B0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305605C0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305605D0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305605E0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ > 2B1305605F0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ This one has a write timestamp of Mon Apr 04 16:02:53 EDT 2016. So more than half of this volume is old data, possibly part of an empty default setup. The latter part of the disk, but less than half, is more recent data. I don't have anything more to suggest. I don't know of any way to get just the good data, however much, at the end of the volume without the first half of the disk. Sorry, Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-23 20:50 ` Phil Turmel @ 2016-07-23 22:21 ` Bhatia Amit 2016-07-23 22:30 ` Phil Turmel 0 siblings, 1 reply; 12+ messages in thread From: Bhatia Amit @ 2016-07-23 22:21 UTC (permalink / raw) To: Phil Turmel, linux-raid > This one has a write timestamp of Mon Apr 04 16:02:53 EDT 2016. > > So more than half of this volume is old data, possibly part of an empty > default setup. The latter part of the disk, but less than half, is more > recent data. > > I don't have anything more to suggest. I don't know of any way to get > just the good data, however much, at the end of the volume without the > first half of the disk. Hi Phil Just to clarify, I am ok getting *all* data out of disk, whether old or new. My key issue is that while r-linux showed me files that it could recover, it did not show me any folder information. So, if getting folder information out requires getting all data out, I am fine with it. What is the way to get this information out for all data? Maybe I am missing something, but is getting data (old/new) out from disk too difficult ? In an earlier email, you had suggested possibly running fsck on sdc4 partition. Is that something I should be considering? Thanks, Amit ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-23 22:21 ` Bhatia Amit @ 2016-07-23 22:30 ` Phil Turmel 2016-07-23 22:47 ` Bhatia Amit 0 siblings, 1 reply; 12+ messages in thread From: Phil Turmel @ 2016-07-23 22:30 UTC (permalink / raw) To: Bhatia Amit, linux-raid On 07/23/2016 06:21 PM, Bhatia Amit wrote: > Just to clarify, I am ok getting *all* data out of disk, whether old > or new. My key issue is that while r-linux showed me files that it > could recover, it did not show me any folder information. So, if > getting folder information out requires getting all data out, I am > fine with it. What is the way to get this information out for all > data? Maybe I am missing something, but is getting data (old/new) out > from disk too difficult ? The old and new data are completely different filesystems, I believe. And I suspect the folder data for the latter half of the disk is in the (missing) first half of the disk. Certainly the root folder. If r-linux can recover file contents, that's better than I've got. I doubt you have any folder data for the new < half disk. > In an earlier email, you had suggested possibly running fsck on sdc4 > partition. Is that something I should be considering? No, I don't believe it can handle anything like this. You might want to share this thread with the ext4 list. Phil ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: Cannot start array on disk 2016-07-23 22:30 ` Phil Turmel @ 2016-07-23 22:47 ` Bhatia Amit 0 siblings, 0 replies; 12+ messages in thread From: Bhatia Amit @ 2016-07-23 22:47 UTC (permalink / raw) To: Phil Turmel, linux-raid > The old and new data are completely different filesystems, I believe. > And I suspect the folder data for the latter half of the disk is in the > (missing) first half of the disk. Certainly the root folder. If > r-linux can recover file contents, that's better than I've got. I doubt > you have any folder data for the new < half disk. > > > In an earlier email, you had suggested possibly running fsck on sdc4 > > partition. Is that something I should be considering? > > No, I don't believe it can handle anything like this. You might want to > share this thread with the ext4 list. Hi Phil I think I understand the issue you are describing here. Also, I will share this thread with the ext4 list to get their suggestion. Thanks for the all help. Amit ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2016-07-23 22:47 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <1124605843.526681.1468785592654.JavaMail.yahoo.ref@mail.yahoo.com>
2016-07-17 19:59 ` Cannot start array on disk Bhatia Amit
2016-07-19 9:12 ` Phil Turmel
2016-07-20 2:10 ` Bhatia Amit
2016-07-20 2:52 ` Bhatia Amit
2016-07-20 10:30 ` Phil Turmel
2016-07-21 2:00 ` Bhatia Amit
2016-07-22 14:48 ` Phil Turmel
2016-07-23 4:00 ` Bhatia Amit
2016-07-23 20:50 ` Phil Turmel
2016-07-23 22:21 ` Bhatia Amit
2016-07-23 22:30 ` Phil Turmel
2016-07-23 22:47 ` Bhatia Amit
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.