From: Mauro Carvalho Chehab <mchehab@kernel.org>
To: unlisted-recipients:; (no To-header on input)
Cc: "Mauro Carvalho Chehab" <mchehab@kernel.org>,
"Daniel W. S. Almeida" <dwlsalmeida@gmail.com>,
"Uwe Kleine-König" <uwe@kleine-koenig.org>,
"Christian Hemp" <c.hemp@phytec.de>,
"Ezequiel Garcia" <ezequiel@vanguardiasur.com.ar>,
"Hans Verkuil" <hverkuil@xs4all.nl>,
"Jacopo Mondi" <jacopo@jmondi.org>,
"Jimmy Su" <jimmy.su@intel.com>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>,
"Martina Krasteva" <martinax.krasteva@intel.com>,
"Sakari Ailus" <sakari.ailus@linux.intel.com>,
"Sean Young" <sean@mess.org>, "Shawn Tu" <shawnx.tu@intel.com>,
linux-kernel@vger.kernel.org, linux-media@vger.kernel.org
Subject: [PATCH v2 66/67] media: media/*/Kconfig: sort entries
Date: Mon, 14 Mar 2022 17:35:01 +0100 [thread overview]
Message-ID: <79bfd880f0f7debc6bda04f6f93ec0bd56e58bc7.1647274407.git.mchehab@kernel.org> (raw)
In-Reply-To: <cover.1647274406.git.mchehab@kernel.org>
Currently, the idems inside media Kconfig are out of order.
Sort them using the script below:
<script>
use strict;
use warnings;
my %config;
my @source;
my $out;
sub flush_config()
{
if (scalar %config) {
for my $c (sort keys %config) {
$out .= $config{$c} . "\n";
}
%config = ();
}
return if (!scalar @source);
$out .= "\n";
for my $s (sort @source) {
$out .= $s;
}
$out .= "\n";
@source = ();
}
sub sort_kconfig($)
{
my $fname = shift;
my $cur_config = "";
@source = ();
$out = "";
%config = ();
open IN, $fname or die;
while (<IN>) {
if (m/^config\s+(.*)/) {
$cur_config = $1;
$config{$cur_config} .= $_;
} elsif (m/^source\s+(.*)/) {
push @source, $_;
} elsif (m/^\s+/) {
if ($cur_config eq "") {
$out .= $_;
} else {
$config{$cur_config} .= $_;
}
} else {
flush_config();
$cur_config = "";
$out .= $_;
}
}
close IN or die;
flush_config();
$out =~ s/\n\n+/\n\n/g;
$out =~ s/\n+$/\n/;
open OUT, ">$fname";
print OUT $out;
close OUT;
}
for my $fname(@ARGV) {
sort_kconfig $fname
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
---
To avoid mailbombing on a large number of people, only mailing lists were C/C on the cover.
See [PATCH v2 00/67] at: https://lore.kernel.org/all/cover.1647274406.git.mchehab@kernel.org/
drivers/media/common/Kconfig | 16 +-
drivers/media/dvb-frontends/Kconfig | 759 +++++++++++------------
drivers/media/i2c/Kconfig | 642 +++++++++----------
drivers/media/mmc/Kconfig | 1 +
drivers/media/pci/Kconfig | 29 +-
drivers/media/radio/Kconfig | 334 +++++-----
drivers/media/rc/Kconfig | 382 ++++++------
drivers/media/test-drivers/Kconfig | 6 +-
drivers/media/test-drivers/vidtv/Kconfig | 1 -
drivers/media/tuners/Kconfig | 407 ++++++------
drivers/media/usb/Kconfig | 33 +-
drivers/media/usb/dvb-usb-v2/Kconfig | 26 +-
drivers/media/usb/dvb-usb/Kconfig | 388 ++++++------
drivers/media/usb/gspca/Kconfig | 27 +-
14 files changed, 1540 insertions(+), 1511 deletions(-)
diff --git a/drivers/media/common/Kconfig b/drivers/media/common/Kconfig
index 0f6bde0f793e..a2ae71270054 100644
--- a/drivers/media/common/Kconfig
+++ b/drivers/media/common/Kconfig
@@ -6,23 +6,23 @@ config MEDIA_COMMON_OPTIONS
comment "common driver options"
depends on MEDIA_COMMON_OPTIONS
-config VIDEO_CX2341X
+config CYPRESS_FIRMWARE
tristate
-
-config VIDEO_TVEEPROM
- tristate
- depends on I2C
+ depends on USB
config TTPCI_EEPROM
tristate
depends on I2C
-config CYPRESS_FIRMWARE
+config VIDEO_CX2341X
tristate
- depends on USB
-source "drivers/media/common/videobuf2/Kconfig"
+config VIDEO_TVEEPROM
+ tristate
+ depends on I2C
+
source "drivers/media/common/b2c2/Kconfig"
source "drivers/media/common/saa7146/Kconfig"
source "drivers/media/common/siano/Kconfig"
source "drivers/media/common/v4l2-tpg/Kconfig"
+source "drivers/media/common/videobuf2/Kconfig"
diff --git a/drivers/media/dvb-frontends/Kconfig b/drivers/media/dvb-frontends/Kconfig
index 4101f9b1e731..2ef2ff2a38ff 100644
--- a/drivers/media/dvb-frontends/Kconfig
+++ b/drivers/media/dvb-frontends/Kconfig
@@ -11,6 +11,23 @@ menu "Customise DVB Frontends"
comment "Multistandard (satellite) frontends"
depends on DVB_CORE
+config DVB_M88DS3103
+ tristate "Montage Technology M88DS3103"
+ depends on DVB_CORE && I2C && I2C_MUX
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y when you want to support this frontend.
+
+config DVB_MXL5XX
+ tristate "MaxLinear MxL5xx based tuner-demodulators"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ MaxLinear MxL5xx family of DVB-S/S2 tuners/demodulators.
+
+ Say Y when you want to support these frontends.
+
config DVB_STB0899
tristate "STB0899 based"
depends on DVB_CORE && I2C
@@ -60,23 +77,6 @@ config DVB_STV6111
Say Y when you want to support these frontends.
-config DVB_MXL5XX
- tristate "MaxLinear MxL5xx based tuner-demodulators"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- MaxLinear MxL5xx family of DVB-S/S2 tuners/demodulators.
-
- Say Y when you want to support these frontends.
-
-config DVB_M88DS3103
- tristate "Montage Technology M88DS3103"
- depends on DVB_CORE && I2C && I2C_MUX
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y when you want to support this frontend.
-
comment "Multistandard (cable + terrestrial) frontends"
depends on DVB_CORE
@@ -89,25 +89,6 @@ config DVB_DRXK
Say Y when you want to support this frontend.
-config DVB_TDA18271C2DD
- tristate "NXP TDA18271C2 silicon tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- NXP TDA18271 silicon tuner.
-
- Say Y when you want to support this tuner.
-
-config DVB_SI2165
- tristate "Silicon Labs si2165 based"
- depends on DVB_CORE && I2C
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-C/T demodulator.
-
- Say Y when you want to support this frontend.
-
config DVB_MN88472
tristate "Panasonic MN88472"
depends on DVB_CORE && I2C
@@ -124,6 +105,25 @@ config DVB_MN88473
help
Say Y when you want to support this frontend.
+config DVB_SI2165
+ tristate "Silicon Labs si2165 based"
+ depends on DVB_CORE && I2C
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-C/T demodulator.
+
+ Say Y when you want to support this frontend.
+
+config DVB_TDA18271C2DD
+ tristate "NXP TDA18271C2 silicon tuner"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ NXP TDA18271 silicon tuner.
+
+ Say Y when you want to support this tuner.
+
comment "DVB-S (satellite) frontends"
depends on DVB_CORE
@@ -134,6 +134,27 @@ config DVB_CX24110
help
A DVB-S tuner module. Say Y when you want to support this frontend.
+config DVB_CX24116
+ tristate "Conexant CX24116 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S/S2 tuner module. Say Y when you want to support this frontend.
+
+config DVB_CX24117
+ tristate "Conexant CX24117 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A Dual DVB-S/S2 tuner module. Say Y when you want to support this frontend.
+
+config DVB_CX24120
+ tristate "Conexant CX24120 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S/S2 tuner module. Say Y when you want to support this frontend.
+
config DVB_CX24123
tristate "Conexant CX24123 based"
depends on DVB_CORE && I2C
@@ -141,6 +162,21 @@ config DVB_CX24123
help
A DVB-S tuner module. Say Y when you want to support this frontend.
+config DVB_DS3000
+ tristate "Montage Tehnology DS3000 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S/S2 tuner module. Say Y when you want to support this frontend.
+
+config DVB_MB86A16
+ tristate "Fujitsu MB86A16 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S/DSS Direct Conversion reveiver.
+ Say Y when you want to support this frontend.
+
config DVB_MT312
tristate "Zarlink VP310/MT312/ZL10313 based"
depends on DVB_CORE && I2C
@@ -148,20 +184,6 @@ config DVB_MT312
help
A DVB-S tuner module. Say Y when you want to support this frontend.
-config DVB_ZL10036
- tristate "Zarlink ZL10036 silicon tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
-config DVB_ZL10039
- tristate "Zarlink ZL10039 silicon tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
config DVB_S5H1420
tristate "Samsung S5H1420 based"
depends on DVB_CORE && I2C
@@ -169,8 +191,8 @@ config DVB_S5H1420
help
A DVB-S tuner module. Say Y when you want to support this frontend.
-config DVB_STV0288
- tristate "ST STV0288 based"
+config DVB_SI21XX
+ tristate "Silicon Labs SI21XX based"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
@@ -183,6 +205,13 @@ config DVB_STB6000
help
A DVB-S silicon tuner module. Say Y when you want to support this tuner.
+config DVB_STV0288
+ tristate "ST STV0288 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module. Say Y when you want to support this frontend.
+
config DVB_STV0299
tristate "ST STV0299 based"
depends on DVB_CORE && I2C
@@ -190,13 +219,6 @@ config DVB_STV0299
help
A DVB-S tuner module. Say Y when you want to support this frontend.
-config DVB_STV6110
- tristate "ST STV6110 silicon tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S silicon tuner module. Say Y when you want to support this tuner.
-
config DVB_STV0900
tristate "ST STV0900 based"
depends on DVB_CORE && I2C
@@ -204,12 +226,20 @@ config DVB_STV0900
help
A DVB-S/S2 demodulator. Say Y when you want to support this frontend.
-config DVB_TDA8083
- tristate "Philips TDA8083 based"
+config DVB_STV6110
+ tristate "ST STV6110 silicon tuner"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-S tuner module. Say Y when you want to support this frontend.
+ A DVB-S silicon tuner module. Say Y when you want to support this tuner.
+
+config DVB_TDA10071
+ tristate "NXP TDA10071"
+ depends on DVB_CORE && I2C
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y when you want to support this frontend.
config DVB_TDA10086
tristate "Philips TDA10086 based"
@@ -218,6 +248,13 @@ config DVB_TDA10086
help
A DVB-S tuner module. Say Y when you want to support this frontend.
+config DVB_TDA8083
+ tristate "Philips TDA8083 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module. Say Y when you want to support this frontend.
+
config DVB_TDA8261
tristate "Philips TDA8261 based"
depends on DVB_CORE && I2C
@@ -225,28 +262,6 @@ config DVB_TDA8261
help
A DVB-S tuner module. Say Y when you want to support this frontend.
-config DVB_VES1X93
- tristate "VLSI VES1893 or VES1993 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
-config DVB_TUNER_ITD1000
- tristate "Integrant ITD1000 Zero IF tuner for DVB-S/DSS"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
-config DVB_TUNER_CX24113
- tristate "Conexant CX24113/CX24128 tuner for DVB-S/DSS"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
-
config DVB_TDA826X
tristate "Philips TDA826X silicon tuner"
depends on DVB_CORE && I2C
@@ -254,41 +269,6 @@ config DVB_TDA826X
help
A DVB-S silicon tuner module. Say Y when you want to support this tuner.
-config DVB_TUA6100
- tristate "Infineon TUA6100 PLL"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S PLL chip.
-
-config DVB_CX24116
- tristate "Conexant CX24116 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S/S2 tuner module. Say Y when you want to support this frontend.
-
-config DVB_CX24117
- tristate "Conexant CX24117 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A Dual DVB-S/S2 tuner module. Say Y when you want to support this frontend.
-
-config DVB_CX24120
- tristate "Conexant CX24120 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S/S2 tuner module. Say Y when you want to support this frontend.
-
-config DVB_SI21XX
- tristate "Silicon Labs SI21XX based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
config DVB_TS2020
tristate "Montage Tehnology TS2020 based tuners"
depends on DVB_CORE && I2C
@@ -297,43 +277,63 @@ config DVB_TS2020
help
A DVB-S/S2 silicon tuner. Say Y when you want to support this tuner.
-config DVB_DS3000
- tristate "Montage Tehnology DS3000 based"
+config DVB_TUA6100
+ tristate "Infineon TUA6100 PLL"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-S/S2 tuner module. Say Y when you want to support this frontend.
+ A DVB-S PLL chip.
-config DVB_MB86A16
- tristate "Fujitsu MB86A16 based"
+config DVB_TUNER_CX24113
+ tristate "Conexant CX24113/CX24128 tuner for DVB-S/DSS"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-S/DSS Direct Conversion reveiver.
- Say Y when you want to support this frontend.
+ A DVB-S tuner module. Say Y when you want to support this frontend.
-config DVB_TDA10071
- tristate "NXP TDA10071"
+config DVB_TUNER_ITD1000
+ tristate "Integrant ITD1000 Zero IF tuner for DVB-S/DSS"
depends on DVB_CORE && I2C
- select REGMAP_I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- Say Y when you want to support this frontend.
+ A DVB-S tuner module. Say Y when you want to support this frontend.
+
+config DVB_VES1X93
+ tristate "VLSI VES1893 or VES1993 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module. Say Y when you want to support this frontend.
+
+config DVB_ZL10036
+ tristate "Zarlink ZL10036 silicon tuner"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module. Say Y when you want to support this frontend.
+
+config DVB_ZL10039
+ tristate "Zarlink ZL10039 silicon tuner"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module. Say Y when you want to support this frontend.
comment "DVB-T (terrestrial) frontends"
depends on DVB_CORE
-config DVB_SP887X
- tristate "Spase sp887x based"
- depends on DVB_CORE && I2C
+config DVB_AF9013
+ tristate "Afatech AF9013 demodulator"
+ depends on DVB_CORE && I2C && I2C_MUX
+ select REGMAP
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-T tuner module. Say Y when you want to support this frontend.
+ Say Y when you want to support this frontend.
- This driver needs external firmware. Please use the command
- "<kerneldir>/scripts/get_dvb_firmware sp887x" to
- download/extract it, and then copy it to /usr/lib/hotplug/firmware
- or /lib/firmware (depending on configuration of firmware hotplug).
+config DVB_AS102_FE
+ tristate
+ depends on DVB_CORE
+ default DVB_AS102
config DVB_CX22700
tristate "Conexant CX22700 based"
@@ -349,64 +349,20 @@ config DVB_CX22702
help
A DVB-T tuner module. Say Y when you want to support this frontend.
-config DVB_S5H1432
- tristate "Samsung s5h1432 demodulator (OFDM)"
+config DVB_CXD2820R
+ tristate "Sony CXD2820R"
depends on DVB_CORE && I2C
+ select REGMAP_I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-T tuner module. Say Y when you want to support this frontend.
+ Say Y when you want to support this frontend.
-config DVB_DRXD
- tristate "Micronas DRXD driver"
+config DVB_CXD2841ER
+ tristate "Sony CXD2841ER"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-T tuner module. Say Y when you want to support this frontend.
-
- Note: this driver was based on vendor driver reference code (released
- under the GPL) as opposed to the existing drx397xd driver, which
- was written via reverse engineering.
-
-config DVB_L64781
- tristate "LSI L64781"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-T tuner module. Say Y when you want to support this frontend.
-
-config DVB_TDA1004X
- tristate "Philips TDA10045H/TDA10046H based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-T tuner module. Say Y when you want to support this frontend.
-
- This driver needs external firmware. Please use the commands
- "<kerneldir>/scripts/get_dvb_firmware tda10045",
- "<kerneldir>/scripts/get_dvb_firmware tda10046" to
- download/extract them, and then copy them to /usr/lib/hotplug/firmware
- or /lib/firmware (depending on configuration of firmware hotplug).
-
-config DVB_NXT6000
- tristate "NxtWave Communications NXT6000 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-T tuner module. Say Y when you want to support this frontend.
-
-config DVB_MT352
- tristate "Zarlink MT352 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-T tuner module. Say Y when you want to support this frontend.
-
-config DVB_ZL10353
- tristate "Zarlink ZL10353 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-T tuner module. Say Y when you want to support this frontend.
+ Say Y when you want to support this frontend.
config DVB_DIB3000MB
tristate "DiBcom 3000M-B"
@@ -448,20 +404,16 @@ config DVB_DIB9000
A DVB-T tuner module. Designed for mobile usage. Say Y when you want
to support this frontend.
-config DVB_TDA10048
- tristate "Philips TDA10048HN based"
+config DVB_DRXD
+ tristate "Micronas DRXD driver"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
A DVB-T tuner module. Say Y when you want to support this frontend.
-config DVB_AF9013
- tristate "Afatech AF9013 demodulator"
- depends on DVB_CORE && I2C && I2C_MUX
- select REGMAP
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y when you want to support this frontend.
+ Note: this driver was based on vendor driver reference code (released
+ under the GPL) as opposed to the existing drx397xd driver, which
+ was written via reverse engineering.
config DVB_EC100
tristate "E3C EC100"
@@ -470,27 +422,31 @@ config DVB_EC100
help
Say Y when you want to support this frontend.
-config DVB_STV0367
- tristate "ST STV0367 based"
+config DVB_GP8PSK_FE
+ tristate
+ depends on DVB_CORE
+ default DVB_USB_GP8PSK
+
+config DVB_L64781
+ tristate "LSI L64781"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DVB-T/C tuner module. Say Y when you want to support this frontend.
+ A DVB-T tuner module. Say Y when you want to support this frontend.
-config DVB_CXD2820R
- tristate "Sony CXD2820R"
+config DVB_MT352
+ tristate "Zarlink MT352 based"
depends on DVB_CORE && I2C
- select REGMAP_I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- Say Y when you want to support this frontend.
+ A DVB-T tuner module. Say Y when you want to support this frontend.
-config DVB_CXD2841ER
- tristate "Sony CXD2841ER"
+config DVB_NXT6000
+ tristate "NxtWave Communications NXT6000 based"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- Say Y when you want to support this frontend.
+ A DVB-T tuner module. Say Y when you want to support this frontend.
config DVB_RTL2830
tristate "Realtek RTL2830 DVB-T"
@@ -517,6 +473,13 @@ config DVB_RTL2832_SDR
help
Say Y when you want to support this SDR module.
+config DVB_S5H1432
+ tristate "Samsung s5h1432 demodulator (OFDM)"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T tuner module. Say Y when you want to support this frontend.
+
config DVB_SI2168
tristate "Silicon Labs Si2168"
depends on DVB_CORE && I2C && I2C_MUX
@@ -524,10 +487,44 @@ config DVB_SI2168
help
Say Y when you want to support this frontend.
-config DVB_AS102_FE
- tristate
- depends on DVB_CORE
- default DVB_AS102
+config DVB_SP887X
+ tristate "Spase sp887x based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T tuner module. Say Y when you want to support this frontend.
+
+ This driver needs external firmware. Please use the command
+ "<kerneldir>/scripts/get_dvb_firmware sp887x" to
+ download/extract it, and then copy it to /usr/lib/hotplug/firmware
+ or /lib/firmware (depending on configuration of firmware hotplug).
+
+config DVB_STV0367
+ tristate "ST STV0367 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T/C tuner module. Say Y when you want to support this frontend.
+
+config DVB_TDA10048
+ tristate "Philips TDA10048HN based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T tuner module. Say Y when you want to support this frontend.
+
+config DVB_TDA1004X
+ tristate "Philips TDA10045H/TDA10046H based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T tuner module. Say Y when you want to support this frontend.
+
+ This driver needs external firmware. Please use the commands
+ "<kerneldir>/scripts/get_dvb_firmware tda10045",
+ "<kerneldir>/scripts/get_dvb_firmware tda10046" to
+ download/extract them, and then copy them to /usr/lib/hotplug/firmware
+ or /lib/firmware (depending on configuration of firmware hotplug).
config DVB_ZD1301_DEMOD
tristate "ZyDAS ZD1301"
@@ -536,18 +533,20 @@ config DVB_ZD1301_DEMOD
help
Say Y when you want to support this frontend.
-config DVB_GP8PSK_FE
- tristate
- depends on DVB_CORE
- default DVB_USB_GP8PSK
+config DVB_ZL10353
+ tristate "Zarlink ZL10353 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T tuner module. Say Y when you want to support this frontend.
source "drivers/media/dvb-frontends/cxd2880/Kconfig"
comment "DVB-C (cable) frontends"
depends on DVB_CORE
-config DVB_VES1820
- tristate "VLSI VES1820 based"
+config DVB_STV0297
+ tristate "ST STV0297 based"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
@@ -567,8 +566,8 @@ config DVB_TDA10023
help
A DVB-C tuner module. Say Y when you want to support this frontend.
-config DVB_STV0297
- tristate "ST STV0297 based"
+config DVB_VES1820
+ tristate "VLSI VES1820 based"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
@@ -577,6 +576,77 @@ config DVB_STV0297
comment "ATSC (North American/Korean Terrestrial/Cable DTV) frontends"
depends on DVB_CORE
+config DVB_AU8522
+ depends on DVB_CORE && I2C
+ tristate
+
+config DVB_AU8522_DTV
+ tristate "Auvitek AU8522 based DTV demod"
+ depends on DVB_CORE && I2C
+ select DVB_AU8522
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC 8VSB, QAM64/256 & NTSC demodulator module. Say Y when
+ you want to enable DTV demodulation support for this frontend.
+
+config DVB_AU8522_V4L
+ tristate "Auvitek AU8522 based ATV demod"
+ depends on VIDEO_DEV && DVB_CORE && I2C
+ select DVB_AU8522
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC 8VSB, QAM64/256 & NTSC demodulator module. Say Y when
+ you want to enable ATV demodulation support for this frontend.
+
+config DVB_BCM3510
+ tristate "Broadcom BCM3510"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC 8VSB/16VSB and QAM64/256 tuner module. Say Y when you want to
+ support this frontend.
+
+config DVB_LG2160
+ tristate "LG Electronics LG216x based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC/MH demodulator module. Say Y when you want
+ to support this frontend.
+
+config DVB_LGDT3305
+ tristate "LG Electronics LGDT3304 and LGDT3305 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
+ to support this frontend.
+
+config DVB_LGDT3306A
+ tristate "LG Electronics LGDT3306A based"
+ depends on DVB_CORE && I2C && I2C_MUX
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC 8VSB and QAM-B 64/256 demodulator module. Say Y when you want
+ to support this frontend.
+
+config DVB_LGDT330X
+ tristate "LG Electronics LGDT3302/LGDT3303 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
+ to support this frontend.
+
+config DVB_MXL692
+ tristate "MaxLinear MXL692 based"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ MaxLinear MxL692 is a combo tuner-demodulator that
+ supports ATSC 8VSB and QAM modes. Say Y when you want to
+ support this frontend.
+
config DVB_NXT200X
tristate "NxtWave Communications NXT2002/NXT2004 based"
depends on DVB_CORE && I2C
@@ -591,18 +661,6 @@ config DVB_NXT200X
download/extract them, and then copy them to /usr/lib/hotplug/firmware
or /lib/firmware (depending on configuration of firmware hotplug).
-config DVB_OR51211
- tristate "Oren OR51211 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC 8VSB tuner module. Say Y when you want to support this frontend.
-
- This driver needs external firmware. Please use the command
- "<kerneldir>/scripts/get_dvb_firmware or51211" to
- download it, and then copy it to /usr/lib/hotplug/firmware
- or /lib/firmware (depending on configuration of firmware hotplug).
-
config DVB_OR51132
tristate "Oren OR51132 based"
depends on DVB_CORE && I2C
@@ -618,45 +676,17 @@ config DVB_OR51132
/usr/lib/hotplug/firmware or /lib/firmware (depending on
configuration of firmware hotplug).
-config DVB_BCM3510
- tristate "Broadcom BCM3510"
+config DVB_OR51211
+ tristate "Oren OR51211 based"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- An ATSC 8VSB/16VSB and QAM64/256 tuner module. Say Y when you want to
- support this frontend.
+ An ATSC 8VSB tuner module. Say Y when you want to support this frontend.
-config DVB_LGDT330X
- tristate "LG Electronics LGDT3302/LGDT3303 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
- to support this frontend.
-
-config DVB_LGDT3305
- tristate "LG Electronics LGDT3304 and LGDT3305 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
- to support this frontend.
-
-config DVB_LGDT3306A
- tristate "LG Electronics LGDT3306A based"
- depends on DVB_CORE && I2C && I2C_MUX
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC 8VSB and QAM-B 64/256 demodulator module. Say Y when you want
- to support this frontend.
-
-config DVB_LG2160
- tristate "LG Electronics LG216x based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC/MH demodulator module. Say Y when you want
- to support this frontend.
+ This driver needs external firmware. Please use the command
+ "<kerneldir>/scripts/get_dvb_firmware or51211" to
+ download it, and then copy it to /usr/lib/hotplug/firmware
+ or /lib/firmware (depending on configuration of firmware hotplug).
config DVB_S5H1409
tristate "Samsung S5H1409 based"
@@ -666,28 +696,6 @@ config DVB_S5H1409
An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
to support this frontend.
-config DVB_AU8522
- depends on DVB_CORE && I2C
- tristate
-
-config DVB_AU8522_DTV
- tristate "Auvitek AU8522 based DTV demod"
- depends on DVB_CORE && I2C
- select DVB_AU8522
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC 8VSB, QAM64/256 & NTSC demodulator module. Say Y when
- you want to enable DTV demodulation support for this frontend.
-
-config DVB_AU8522_V4L
- tristate "Auvitek AU8522 based ATV demod"
- depends on VIDEO_DEV && DVB_CORE && I2C
- select DVB_AU8522
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- An ATSC 8VSB, QAM64/256 & NTSC demodulator module. Say Y when
- you want to enable ATV demodulation support for this frontend.
-
config DVB_S5H1411
tristate "Samsung S5H1411 based"
depends on DVB_CORE && I2C
@@ -696,26 +704,9 @@ config DVB_S5H1411
An ATSC 8VSB and QAM64/256 tuner module. Say Y when you want
to support this frontend.
-config DVB_MXL692
- tristate "MaxLinear MXL692 based"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- MaxLinear MxL692 is a combo tuner-demodulator that
- supports ATSC 8VSB and QAM modes. Say Y when you want to
- support this frontend.
-
comment "ISDB-T (terrestrial) frontends"
depends on DVB_CORE
-config DVB_S921
- tristate "Sharp S921 frontend"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- AN ISDB-T DQPSK, QPSK, 16QAM and 64QAM 1seg tuner module.
- Say Y when you want to support this frontend.
-
config DVB_DIB8000
tristate "DiBcom 8000MB/MC"
depends on DVB_CORE && I2C
@@ -732,17 +723,17 @@ config DVB_MB86A20S
A driver for Fujitsu mb86a20s ISDB-T/ISDB-Tsb demodulator.
Say Y when you want to support this frontend.
+config DVB_S921
+ tristate "Sharp S921 frontend"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ AN ISDB-T DQPSK, QPSK, 16QAM and 64QAM 1seg tuner module.
+ Say Y when you want to support this frontend.
+
comment "ISDB-S (satellite) & ISDB-T (terrestrial) frontends"
depends on DVB_CORE
-config DVB_TC90522
- tristate "Toshiba TC90522"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Toshiba TC90522 2xISDB-S 8PSK + 2xISDB-T OFDM demodulator.
- Say Y when you want to support this frontend.
-
config DVB_MN88443X
tristate "Socionext MN88443x"
depends on DVB_CORE && I2C
@@ -753,6 +744,14 @@ config DVB_MN88443X
ISDB-S + ISDB-T demodulator.
Say Y when you want to support this frontend.
+config DVB_TC90522
+ tristate "Toshiba TC90522"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Toshiba TC90522 2xISDB-S 8PSK + 2xISDB-T OFDM demodulator.
+ Say Y when you want to support this frontend.
+
comment "Digital terrestrial only tuners/PLL"
depends on DVB_CORE
@@ -785,42 +784,44 @@ config DVB_TUNER_DIB0090
comment "SEC control devices for DVB-S"
depends on DVB_CORE
-source "drivers/media/dvb-frontends/drx39xyj/Kconfig"
+config DVB_A8293
+ tristate "Allegro A8293"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+
+config DVB_AF9033
+ tristate "Afatech AF9033 DVB-T demodulator"
+ depends on DVB_CORE && I2C
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
-config DVB_LNBH25
- tristate "LNBH25 SEC controller"
+config DVB_ASCOT2E
+ tristate "Sony Ascot2E tuner"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- An SEC control chip.
- Say Y when you want to support this chip.
+ Say Y when you want to support this frontend.
-config DVB_LNBH29
- tristate "LNBH29 SEC controller"
+config DVB_ATBM8830
+ tristate "AltoBeam ATBM8830/8831 DMB-TH demodulator"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- LNB power supply and control voltage
- regulator chip with step-up converter
- and I2C interface for STMicroelectronics LNBH29.
- Say Y when you want to support this chip.
+ A DMB-TH tuner module. Say Y when you want to support this frontend.
-config DVB_LNBP21
- tristate "LNBP21/LNBH24 SEC controllers"
+config DVB_HELENE
+ tristate "Sony HELENE Sat/Ter tuner (CXD2858ER)"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- An SEC control chips.
+ Say Y when you want to support this frontend.
-config DVB_LNBP22
- tristate "LNBP22 SEC controllers"
+config DVB_HORUS3A
+ tristate "Sony Horus3A tuner"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- LNB power supply and control voltage
- regulator chip with step-up converter
- and I2C interface.
- Say Y when you want to support this chip.
+ Say Y when you want to support this frontend.
config DVB_ISL6405
tristate "ISL6405 SEC controller"
@@ -843,10 +844,12 @@ config DVB_ISL6423
help
A SEC controller chip from Intersil
-config DVB_A8293
- tristate "Allegro A8293"
+config DVB_IX2505V
+ tristate "Sharp IX2505V silicon tuner"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module. Say Y when you want to support this frontend.
config DVB_LGS8GL5
tristate "Silicon Legend LGS-8GL5 demodulator (OFDM)"
@@ -863,12 +866,48 @@ config DVB_LGS8GXX
help
A DMB-TH tuner module. Say Y when you want to support this frontend.
-config DVB_ATBM8830
- tristate "AltoBeam ATBM8830/8831 DMB-TH demodulator"
+config DVB_LNBH25
+ tristate "LNBH25 SEC controller"
depends on DVB_CORE && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A DMB-TH tuner module. Say Y when you want to support this frontend.
+ An SEC control chip.
+ Say Y when you want to support this chip.
+
+config DVB_LNBH29
+ tristate "LNBH29 SEC controller"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ LNB power supply and control voltage
+ regulator chip with step-up converter
+ and I2C interface for STMicroelectronics LNBH29.
+ Say Y when you want to support this chip.
+
+config DVB_LNBP21
+ tristate "LNBP21/LNBH24 SEC controllers"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ An SEC control chips.
+
+config DVB_LNBP22
+ tristate "LNBP22 SEC controllers"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ LNB power supply and control voltage
+ regulator chip with step-up converter
+ and I2C interface.
+ Say Y when you want to support this chip.
+
+config DVB_M88RS2000
+ tristate "M88RS2000 DVB-S demodulator and tuner"
+ depends on DVB_CORE && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-S tuner module.
+ Say Y when you want to support this frontend.
config DVB_TDA665x
tristate "TDA665x tuner"
@@ -881,47 +920,7 @@ config DVB_TDA665x
Currently supported tuners:
* Panasonic ENV57H12D5 (ET-50DT)
-config DVB_IX2505V
- tristate "Sharp IX2505V silicon tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module. Say Y when you want to support this frontend.
-
-config DVB_M88RS2000
- tristate "M88RS2000 DVB-S demodulator and tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-S tuner module.
- Say Y when you want to support this frontend.
-
-config DVB_AF9033
- tristate "Afatech AF9033 DVB-T demodulator"
- depends on DVB_CORE && I2C
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
-
-config DVB_HORUS3A
- tristate "Sony Horus3A tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y when you want to support this frontend.
-
-config DVB_ASCOT2E
- tristate "Sony Ascot2E tuner"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y when you want to support this frontend.
-
-config DVB_HELENE
- tristate "Sony HELENE Sat/Ter tuner (CXD2858ER)"
- depends on DVB_CORE && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y when you want to support this frontend.
+source "drivers/media/dvb-frontends/drx39xyj/Kconfig"
comment "Common Interface (EN50221) controller drivers"
depends on DVB_CORE
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 5abc169f0a5c..14fe94f3c772 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -34,17 +34,68 @@ comment "audio, video and radio I2C drivers auto-selected by 'Autoselect ancilla
menu "Audio decoders, processors and mixers"
visible if !MEDIA_HIDE_ANCILLARY_SUBDRV
-config VIDEO_TVAUDIO
- tristate "Simple audio decoder chips"
+config VIDEO_CS3308
+ tristate "Cirrus Logic CS3308 audio ADC"
depends on VIDEO_DEV && I2C
help
- Support for several audio decoder chips found on some bt8xx boards:
- Philips: tda9840, tda9873h, tda9874h/a, tda9850, tda985x, tea6300,
- tea6320, tea6420, tda8425, ta8874z.
- Microchip: pic16c54 based design on ProVideo PV951 board.
+ Support for the Cirrus Logic CS3308 High Performance 8-Channel
+ Analog Volume Control
To compile this driver as a module, choose M here: the
- module will be called tvaudio.
+ module will be called cs3308.
+
+config VIDEO_CS5345
+ tristate "Cirrus Logic CS5345 audio ADC"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the Cirrus Logic CS5345 24-bit, 192 kHz
+ stereo A/D converter.
+
+ To compile this driver as a module, choose M here: the
+ module will be called cs5345.
+
+config VIDEO_CS53L32A
+ tristate "Cirrus Logic CS53L32A audio ADC"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the Cirrus Logic CS53L32A low voltage
+ stereo A/D converter.
+
+ To compile this driver as a module, choose M here: the
+ module will be called cs53l32a.
+
+config VIDEO_MSP3400
+ tristate "Micronas MSP34xx audio decoders"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the Micronas MSP34xx series of audio decoders.
+
+ To compile this driver as a module, choose M here: the
+ module will be called msp3400.
+
+config VIDEO_SONY_BTF_MPX
+ tristate "Sony BTF's internal MPX"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the internal MPX of the Sony BTF-PG472Z tuner.
+
+ To compile this driver as a module, choose M here: the
+ module will be called sony-btf-mpx.
+
+config VIDEO_TDA1997X
+ tristate "NXP TDA1997x HDMI receiver"
+ depends on VIDEO_DEV && I2C
+ depends on SND_SOC
+ select HDMI
+ select SND_PCM
+ select V4L2_FWNODE
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ V4L2 subdevice driver for the NXP TDA1997x HDMI receivers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tda1997x.
config VIDEO_TDA7432
tristate "Philips TDA7432 audio processor"
@@ -64,21 +115,6 @@ config VIDEO_TDA9840
To compile this driver as a module, choose M here: the
module will be called tda9840.
-config VIDEO_TDA1997X
- tristate "NXP TDA1997x HDMI receiver"
- depends on VIDEO_DEV && I2C
- depends on SND_SOC
- select HDMI
- select SND_PCM
- select V4L2_FWNODE
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- help
- V4L2 subdevice driver for the NXP TDA1997x HDMI receivers.
-
- To compile this driver as a module, choose M here: the
- module will be called tda1997x.
-
config VIDEO_TEA6415C
tristate "Philips TEA6415C audio processor"
depends on I2C
@@ -97,45 +133,6 @@ config VIDEO_TEA6420
To compile this driver as a module, choose M here: the
module will be called tea6420.
-config VIDEO_MSP3400
- tristate "Micronas MSP34xx audio decoders"
- depends on VIDEO_DEV && I2C
- help
- Support for the Micronas MSP34xx series of audio decoders.
-
- To compile this driver as a module, choose M here: the
- module will be called msp3400.
-
-config VIDEO_CS3308
- tristate "Cirrus Logic CS3308 audio ADC"
- depends on VIDEO_DEV && I2C
- help
- Support for the Cirrus Logic CS3308 High Performance 8-Channel
- Analog Volume Control
-
- To compile this driver as a module, choose M here: the
- module will be called cs3308.
-
-config VIDEO_CS5345
- tristate "Cirrus Logic CS5345 audio ADC"
- depends on VIDEO_DEV && I2C
- help
- Support for the Cirrus Logic CS5345 24-bit, 192 kHz
- stereo A/D converter.
-
- To compile this driver as a module, choose M here: the
- module will be called cs5345.
-
-config VIDEO_CS53L32A
- tristate "Cirrus Logic CS53L32A audio ADC"
- depends on VIDEO_DEV && I2C
- help
- Support for the Cirrus Logic CS53L32A low voltage
- stereo A/D converter.
-
- To compile this driver as a module, choose M here: the
- module will be called cs53l32a.
-
config VIDEO_TLV320AIC23B
tristate "Texas Instruments TLV320AIC23B audio codec"
depends on VIDEO_DEV && I2C
@@ -145,6 +142,18 @@ config VIDEO_TLV320AIC23B
To compile this driver as a module, choose M here: the
module will be called tlv320aic23b.
+config VIDEO_TVAUDIO
+ tristate "Simple audio decoder chips"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for several audio decoder chips found on some bt8xx boards:
+ Philips: tda9840, tda9873h, tda9874h/a, tda9850, tda985x, tea6300,
+ tea6320, tea6420, tda8425, ta8874z.
+ Microchip: pic16c54 based design on ProVideo PV951 board.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tvaudio.
+
config VIDEO_UDA1342
tristate "Philips UDA1342 audio codec"
depends on VIDEO_DEV && I2C
@@ -154,15 +163,14 @@ config VIDEO_UDA1342
To compile this driver as a module, choose M here: the
module will be called uda1342.
-config VIDEO_WM8775
- tristate "Wolfson Microelectronics WM8775 audio ADC with input mixer"
+config VIDEO_VP27SMPX
+ tristate "Panasonic VP27's internal MPX"
depends on VIDEO_DEV && I2C
help
- Support for the Wolfson Microelectronics WM8775 high
- performance stereo A/D Converter with a 4 channel input mixer.
+ Support for the internal MPX of the Panasonic VP27s tuner.
To compile this driver as a module, choose M here: the
- module will be called wm8775.
+ module will be called vp27smpx.
config VIDEO_WM8739
tristate "Wolfson Microelectronics WM8739 stereo audio ADC"
@@ -174,23 +182,16 @@ config VIDEO_WM8739
To compile this driver as a module, choose M here: the
module will be called wm8739.
-config VIDEO_VP27SMPX
- tristate "Panasonic VP27's internal MPX"
+config VIDEO_WM8775
+ tristate "Wolfson Microelectronics WM8775 audio ADC with input mixer"
depends on VIDEO_DEV && I2C
help
- Support for the internal MPX of the Panasonic VP27s tuner.
+ Support for the Wolfson Microelectronics WM8775 high
+ performance stereo A/D Converter with a 4 channel input mixer.
To compile this driver as a module, choose M here: the
- module will be called vp27smpx.
+ module will be called wm8775.
-config VIDEO_SONY_BTF_MPX
- tristate "Sony BTF's internal MPX"
- depends on VIDEO_DEV && I2C
- help
- Support for the internal MPX of the Sony BTF-PG472Z tuner.
-
- To compile this driver as a module, choose M here: the
- module will be called sony-btf-mpx.
endmenu
menu "RDS decoders"
@@ -207,6 +208,7 @@ config VIDEO_SAA6588
To compile this driver as a module, choose M here: the
module will be called saa6588.
+
endmenu
menu "Video decoders"
@@ -347,6 +349,20 @@ config VIDEO_KS0127
To compile this driver as a module, choose M here: the
module will be called ks0127.
+config VIDEO_MAX9286
+ tristate "Maxim MAX9286 GMSL deserializer support"
+ depends on I2C && I2C_MUX
+ depends on VIDEO_DEV
+ depends on OF_GPIO
+ select V4L2_FWNODE
+ select VIDEO_V4L2_SUBDEV_API
+ select MEDIA_CONTROLLER
+ help
+ This driver supports the Maxim MAX9286 GMSL deserializer.
+
+ To compile this driver as a module, choose M here: the
+ module will be called max9286.
+
config VIDEO_ML86V7667
tristate "OKI ML86V7667 video decoder"
depends on VIDEO_DEV && I2C
@@ -476,20 +492,6 @@ config VIDEO_VPX3220
To compile this driver as a module, choose M here: the
module will be called vpx3220.
-config VIDEO_MAX9286
- tristate "Maxim MAX9286 GMSL deserializer support"
- depends on I2C && I2C_MUX
- depends on VIDEO_DEV
- depends on OF_GPIO
- select V4L2_FWNODE
- select VIDEO_V4L2_SUBDEV_API
- select MEDIA_CONTROLLER
- help
- This driver supports the Maxim MAX9286 GMSL deserializer.
-
- To compile this driver as a module, choose M here: the
- module will be called max9286.
-
comment "Video and audio decoders"
config VIDEO_SAA717X
@@ -508,23 +510,19 @@ endmenu
menu "Video encoders"
visible if !MEDIA_HIDE_ANCILLARY_SUBDRV
-config VIDEO_SAA7127
- tristate "Philips SAA7127/9 digital video encoders"
+config VIDEO_AD9389B
+ tristate "Analog Devices AD9389B encoder"
depends on VIDEO_DEV && I2C
- help
- Support for the Philips SAA7127/9 digital video encoders.
-
- To compile this driver as a module, choose M here: the
- module will be called saa7127.
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
-config VIDEO_SAA7185
- tristate "Philips SAA7185 video encoder"
- depends on VIDEO_DEV && I2C
help
- Support for the Philips SAA7185 video encoder.
+ Support for the Analog Devices AD9389B video encoder.
+
+ This is a Analog Devices HDMI transmitter.
To compile this driver as a module, choose M here: the
- module will be called saa7185.
+ module will be called ad9389b.
config VIDEO_ADV7170
tristate "Analog Devices ADV7170 video encoder"
@@ -586,26 +584,30 @@ config VIDEO_ADV7511_CEC
When selected the adv7511 will support the optional
HDMI CEC feature.
-config VIDEO_AD9389B
- tristate "Analog Devices AD9389B encoder"
- depends on VIDEO_DEV && I2C
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
-
- help
- Support for the Analog Devices AD9389B video encoder.
-
- This is a Analog Devices HDMI transmitter.
-
- To compile this driver as a module, choose M here: the
- module will be called ad9389b.
-
config VIDEO_AK881X
tristate "AK8813/AK8814 video encoders"
depends on I2C
help
Video output driver for AKM AK8813 and AK8814 TV encoders
+config VIDEO_SAA7127
+ tristate "Philips SAA7127/9 digital video encoders"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the Philips SAA7127/9 digital video encoders.
+
+ To compile this driver as a module, choose M here: the
+ module will be called saa7127.
+
+config VIDEO_SAA7185
+ tristate "Philips SAA7185 video encoder"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the Philips SAA7185 video encoder.
+
+ To compile this driver as a module, choose M here: the
+ module will be called saa7185.
+
config VIDEO_THS8200
tristate "Texas Instruments THS8200 video encoder"
depends on VIDEO_DEV && I2C
@@ -615,6 +617,7 @@ config VIDEO_THS8200
To compile this driver as a module, choose M here: the
module will be called ths8200.
+
endmenu
menu "Video improvement chips"
@@ -643,6 +646,7 @@ config VIDEO_UPD64083
To compile this driver as a module, choose M here: the
module will be called upd64083.
+
endmenu
menu "Audio/Video compression chips"
@@ -676,31 +680,11 @@ config SDR_MAX2175
To compile this driver as a module, choose M here; the
module will be called max2175.
-
endmenu
menu "Miscellaneous helper chips"
visible if !MEDIA_HIDE_ANCILLARY_SUBDRV
-config VIDEO_THS7303
- tristate "THS7303/53 Video Amplifier"
- depends on VIDEO_DEV && I2C
- select V4L2_ASYNC
- help
- Support for TI THS7303/53 video amplifier
-
- To compile this driver as a module, choose M here: the
- module will be called ths7303.
-
-config VIDEO_M52790
- tristate "Mitsubishi M52790 A/V switch"
- depends on VIDEO_DEV && I2C
- help
- Support for the Mitsubishi M52790 A/V switch.
-
- To compile this driver as a module, choose M here: the
- module will be called m52790.
-
config VIDEO_I2C
tristate "I2C transport video support"
depends on VIDEO_DEV && I2C
@@ -715,6 +699,15 @@ config VIDEO_I2C
To compile this driver as a module, choose M here: the
module will be called video-i2c
+config VIDEO_M52790
+ tristate "Mitsubishi M52790 A/V switch"
+ depends on VIDEO_DEV && I2C
+ help
+ Support for the Mitsubishi M52790 A/V switch.
+
+ To compile this driver as a module, choose M here: the
+ module will be called m52790.
+
config VIDEO_ST_MIPID02
tristate "STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge"
depends on I2C && VIDEO_DEV
@@ -728,6 +721,17 @@ config VIDEO_ST_MIPID02
To compile this driver as a module, choose M here: the
module will be called st-mipid02.
+
+config VIDEO_THS7303
+ tristate "THS7303/53 Video Amplifier"
+ depends on VIDEO_DEV && I2C
+ select V4L2_ASYNC
+ help
+ Support for TI THS7303/53 video amplifier
+
+ To compile this driver as a module, choose M here: the
+ module will be called ths7303.
+
endmenu
#
@@ -922,6 +926,103 @@ config VIDEO_IMX412
To compile this driver as a module, choose M here: the
module will be called imx412.
+config VIDEO_MAX9271_LIB
+ tristate
+
+config VIDEO_MT9M001
+ tristate "mt9m001 support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ This driver supports MT9M001 cameras from Micron, monochrome
+ and colour models.
+
+config VIDEO_MT9M032
+ tristate "MT9M032 camera sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ select VIDEO_APTINA_PLL
+ help
+ This driver supports MT9M032 camera sensors from Aptina, monochrome
+ models only.
+
+config VIDEO_MT9M111
+ tristate "mt9m111, mt9m112 and mt9m131 support"
+ depends on I2C && VIDEO_DEV
+ select V4L2_FWNODE
+ help
+ This driver supports MT9M111, MT9M112 and MT9M131 cameras from
+ Micron/Aptina
+
+config VIDEO_MT9P031
+ tristate "Aptina MT9P031 support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ select VIDEO_APTINA_PLL
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the Aptina
+ (Micron) mt9p031 5 Mpixel camera.
+
+config VIDEO_MT9T001
+ tristate "Aptina MT9T001 support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ This is a Video4Linux2 sensor driver for the Aptina
+ (Micron) mt0t001 3 Mpixel camera.
+
+config VIDEO_MT9T112
+ tristate "Aptina MT9T111/MT9T112 support"
+ depends on I2C && VIDEO_DEV
+ help
+ This is a Video4Linux2 sensor driver for the Aptina
+ (Micron) MT9T111 and MT9T112 3 Mpixel camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mt9t112.
+
+config VIDEO_MT9V011
+ tristate "Micron mt9v011 sensor support"
+ depends on I2C && VIDEO_DEV
+ help
+ This is a Video4Linux2 sensor driver for the Micron
+ mt0v011 1.3 Mpixel camera. It currently only works with the
+ em28xx driver.
+
+config VIDEO_MT9V032
+ tristate "Micron MT9V032 sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ select REGMAP_I2C
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the Micron
+ MT9V032 752x480 CMOS sensor.
+
+config VIDEO_MT9V111
+ tristate "Aptina MT9V111 sensor support"
+ depends on I2C && VIDEO_DEV
+ help
+ This is a Video4Linux2 sensor driver for the Aptina/Micron
+ MT9V111 sensor.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mt9v111.
+
+config VIDEO_NOON010PC30
+ tristate "Siliconfile NOON010PC30 sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ This driver supports NOON010PC30 CIF camera from Siliconfile
+
config VIDEO_OG01A1B
tristate "OmniVision OG01A1B sensor support"
depends on I2C && VIDEO_DEV
@@ -961,6 +1062,26 @@ config VIDEO_OV08D10
To compile this driver as a module, choose M here: the
module will be called ov08d10.
+config VIDEO_OV13858
+ tristate "OmniVision OV13858 sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the OmniVision
+ OV13858 camera.
+
+config VIDEO_OV13B10
+ tristate "OmniVision OV13B10 sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the OmniVision
+ OV13B10 camera.
+
config VIDEO_OV2640
tristate "OmniVision OV2640 sensor support"
depends on VIDEO_DEV && I2C
@@ -1072,16 +1193,6 @@ config VIDEO_OV5648
To compile this driver as a module, choose M here: the
module will be called ov5648.
-config VIDEO_OV6650
- tristate "OmniVision OV6650 sensor support"
- depends on I2C && VIDEO_DEV
- help
- This is a Video4Linux2 sensor driver for the OmniVision
- OV6650 camera.
-
- To compile this driver as a module, choose M here: the
- module will be called ov6650.
-
config VIDEO_OV5670
tristate "OmniVision OV5670 sensor support"
depends on I2C && VIDEO_DEV
@@ -1130,6 +1241,16 @@ config VIDEO_OV5695
To compile this driver as a module, choose M here: the
module will be called ov5695.
+config VIDEO_OV6650
+ tristate "OmniVision OV6650 sensor support"
+ depends on I2C && VIDEO_DEV
+ help
+ This is a Video4Linux2 sensor driver for the OmniVision
+ OV6650 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov6650.
+
config VIDEO_OV7251
tristate "OmniVision OV7251 sensor support"
depends on I2C && VIDEO_DEV
@@ -1143,18 +1264,6 @@ config VIDEO_OV7251
To compile this driver as a module, choose M here: the
module will be called ov7251.
-config VIDEO_OV772X
- tristate "OmniVision OV772x sensor support"
- depends on I2C && VIDEO_DEV
- select REGMAP_SCCB
- select V4L2_FWNODE
- help
- This is a Video4Linux2 sensor driver for the OmniVision
- OV772x camera.
-
- To compile this driver as a module, choose M here: the
- module will be called ov772x.
-
config VIDEO_OV7640
tristate "OmniVision OV7640 sensor support"
depends on I2C && VIDEO_DEV
@@ -1174,6 +1283,18 @@ config VIDEO_OV7670
OV7670 VGA camera. It currently only works with the M88ALP01
controller.
+config VIDEO_OV772X
+ tristate "OmniVision OV772x sensor support"
+ depends on I2C && VIDEO_DEV
+ select REGMAP_SCCB
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the OmniVision
+ OV772x camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov772x.
+
config VIDEO_OV7740
tristate "OmniVision OV7740 sensor support"
depends on I2C && VIDEO_DEV
@@ -1253,141 +1374,6 @@ config VIDEO_OV9734
To compile this driver as a module, choose M here: the
module's name is ov9734.
-config VIDEO_OV13858
- tristate "OmniVision OV13858 sensor support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- select V4L2_FWNODE
- help
- This is a Video4Linux2 sensor driver for the OmniVision
- OV13858 camera.
-
-config VIDEO_OV13B10
- tristate "OmniVision OV13B10 sensor support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- select V4L2_FWNODE
- help
- This is a Video4Linux2 sensor driver for the OmniVision
- OV13B10 camera.
-
-config VIDEO_VS6624
- tristate "ST VS6624 sensor support"
- depends on VIDEO_DEV && I2C
- help
- This is a Video4Linux2 sensor driver for the ST VS6624
- camera.
-
- To compile this driver as a module, choose M here: the
- module will be called vs6624.
-
-config VIDEO_MT9M001
- tristate "mt9m001 support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- help
- This driver supports MT9M001 cameras from Micron, monochrome
- and colour models.
-
-config VIDEO_MT9M032
- tristate "MT9M032 camera sensor support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- select VIDEO_APTINA_PLL
- help
- This driver supports MT9M032 camera sensors from Aptina, monochrome
- models only.
-
-config VIDEO_MT9M111
- tristate "mt9m111, mt9m112 and mt9m131 support"
- depends on I2C && VIDEO_DEV
- select V4L2_FWNODE
- help
- This driver supports MT9M111, MT9M112 and MT9M131 cameras from
- Micron/Aptina
-
-config VIDEO_MT9P031
- tristate "Aptina MT9P031 support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- select VIDEO_APTINA_PLL
- select V4L2_FWNODE
- help
- This is a Video4Linux2 sensor driver for the Aptina
- (Micron) mt9p031 5 Mpixel camera.
-
-config VIDEO_MT9T001
- tristate "Aptina MT9T001 support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- help
- This is a Video4Linux2 sensor driver for the Aptina
- (Micron) mt0t001 3 Mpixel camera.
-
-config VIDEO_MT9T112
- tristate "Aptina MT9T111/MT9T112 support"
- depends on I2C && VIDEO_DEV
- help
- This is a Video4Linux2 sensor driver for the Aptina
- (Micron) MT9T111 and MT9T112 3 Mpixel camera.
-
- To compile this driver as a module, choose M here: the
- module will be called mt9t112.
-
-config VIDEO_MT9V011
- tristate "Micron mt9v011 sensor support"
- depends on I2C && VIDEO_DEV
- help
- This is a Video4Linux2 sensor driver for the Micron
- mt0v011 1.3 Mpixel camera. It currently only works with the
- em28xx driver.
-
-config VIDEO_MT9V032
- tristate "Micron MT9V032 sensor support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- select REGMAP_I2C
- select V4L2_FWNODE
- help
- This is a Video4Linux2 sensor driver for the Micron
- MT9V032 752x480 CMOS sensor.
-
-config VIDEO_MT9V111
- tristate "Aptina MT9V111 sensor support"
- depends on I2C && VIDEO_DEV
- help
- This is a Video4Linux2 sensor driver for the Aptina/Micron
- MT9V111 sensor.
-
- To compile this driver as a module, choose M here: the
- module will be called mt9v111.
-
-config VIDEO_SR030PC30
- tristate "Siliconfile SR030PC30 sensor support"
- depends on I2C && VIDEO_DEV
- help
- This driver supports SR030PC30 VGA camera from Siliconfile
-
-config VIDEO_NOON010PC30
- tristate "Siliconfile NOON010PC30 sensor support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- help
- This driver supports NOON010PC30 CIF camera from Siliconfile
-
-source "drivers/media/i2c/m5mols/Kconfig"
-
-config VIDEO_MAX9271_LIB
- tristate
-
config VIDEO_RDACM20
tristate "IMI RDACM20 camera support"
depends on I2C
@@ -1426,23 +1412,15 @@ config VIDEO_RJ54N1
To compile this driver as a module, choose M here: the
module will be called rj54n1.
-config VIDEO_S5K6AA
- tristate "Samsung S5K6AAFX sensor support"
- depends on I2C && VIDEO_DEV
+config VIDEO_S5C73M3
+ tristate "Samsung S5C73M3 sensor support"
+ depends on I2C && SPI && VIDEO_DEV
select MEDIA_CONTROLLER
select VIDEO_V4L2_SUBDEV_API
+ select V4L2_FWNODE
help
- This is a V4L2 sensor driver for Samsung S5K6AA(FX) 1.3M
- camera sensor with an embedded SoC image signal processor.
-
-config VIDEO_S5K6A3
- tristate "Samsung S5K6A3 sensor support"
- depends on I2C && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- help
- This is a V4L2 sensor driver for Samsung S5K6A3 raw
- camera sensor.
+ This is a V4L2 sensor driver for Samsung S5C73M3
+ 8 Mpixel camera.
config VIDEO_S5K4ECGX
tristate "Samsung S5K4ECGX sensor support"
@@ -1464,18 +1442,43 @@ config VIDEO_S5K5BAF
This is a V4L2 sensor driver for Samsung S5K5BAF 2M
camera sensor with an embedded SoC image signal processor.
+config VIDEO_S5K6A3
+ tristate "Samsung S5K6A3 sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ This is a V4L2 sensor driver for Samsung S5K6A3 raw
+ camera sensor.
+
+config VIDEO_S5K6AA
+ tristate "Samsung S5K6AAFX sensor support"
+ depends on I2C && VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ This is a V4L2 sensor driver for Samsung S5K6AA(FX) 1.3M
+ camera sensor with an embedded SoC image signal processor.
+
+config VIDEO_SR030PC30
+ tristate "Siliconfile SR030PC30 sensor support"
+ depends on I2C && VIDEO_DEV
+ help
+ This driver supports SR030PC30 VGA camera from Siliconfile
+
+config VIDEO_VS6624
+ tristate "ST VS6624 sensor support"
+ depends on VIDEO_DEV && I2C
+ help
+ This is a Video4Linux2 sensor driver for the ST VS6624
+ camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called vs6624.
+
source "drivers/media/i2c/ccs/Kconfig"
source "drivers/media/i2c/et8ek8/Kconfig"
-
-config VIDEO_S5C73M3
- tristate "Samsung S5C73M3 sensor support"
- depends on I2C && SPI && VIDEO_DEV
- select MEDIA_CONTROLLER
- select VIDEO_V4L2_SUBDEV_API
- select V4L2_FWNODE
- help
- This is a V4L2 sensor driver for Samsung S5C73M3
- 8 Mpixel camera.
+source "drivers/media/i2c/m5mols/Kconfig"
endmenu
@@ -1572,6 +1575,7 @@ config VIDEO_LM3646
help
This is a driver for the lm3646 dual flash controllers. It controls
flash, torch LEDs.
+
endmenu
endif # VIDEO_DEV
diff --git a/drivers/media/mmc/Kconfig b/drivers/media/mmc/Kconfig
index 75aa6de08d53..2f9877bc61e4 100644
--- a/drivers/media/mmc/Kconfig
+++ b/drivers/media/mmc/Kconfig
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0-only
+
source "drivers/media/mmc/siano/Kconfig"
diff --git a/drivers/media/pci/Kconfig b/drivers/media/pci/Kconfig
index 92b156530d91..1224d908713a 100644
--- a/drivers/media/pci/Kconfig
+++ b/drivers/media/pci/Kconfig
@@ -12,50 +12,55 @@ if MEDIA_PCI_SUPPORT
if MEDIA_CAMERA_SUPPORT
comment "Media capture support"
+
source "drivers/media/pci/meye/Kconfig"
source "drivers/media/pci/solo6x10/Kconfig"
source "drivers/media/pci/sta2x11/Kconfig"
source "drivers/media/pci/tw5864/Kconfig"
source "drivers/media/pci/tw68/Kconfig"
source "drivers/media/pci/tw686x/Kconfig"
+
endif
if MEDIA_ANALOG_TV_SUPPORT
comment "Media capture/analog TV support"
+
+source "drivers/media/pci/dt3155/Kconfig"
source "drivers/media/pci/ivtv/Kconfig"
source "drivers/media/pci/saa7146/Kconfig"
-source "drivers/media/pci/dt3155/Kconfig"
+
endif
if MEDIA_ANALOG_TV_SUPPORT || MEDIA_DIGITAL_TV_SUPPORT
comment "Media capture/analog/hybrid TV support"
+
+source "drivers/media/pci/bt8xx/Kconfig"
+source "drivers/media/pci/cobalt/Kconfig"
source "drivers/media/pci/cx18/Kconfig"
source "drivers/media/pci/cx23885/Kconfig"
source "drivers/media/pci/cx25821/Kconfig"
source "drivers/media/pci/cx88/Kconfig"
-source "drivers/media/pci/bt8xx/Kconfig"
source "drivers/media/pci/saa7134/Kconfig"
source "drivers/media/pci/saa7164/Kconfig"
-source "drivers/media/pci/cobalt/Kconfig"
endif
if MEDIA_DIGITAL_TV_SUPPORT
comment "Media digital TV PCI Adapters"
-source "drivers/media/pci/ttpci/Kconfig"
+
source "drivers/media/pci/b2c2/Kconfig"
-source "drivers/media/pci/pluto2/Kconfig"
+source "drivers/media/pci/ddbridge/Kconfig"
source "drivers/media/pci/dm1105/Kconfig"
-source "drivers/media/pci/pt1/Kconfig"
-source "drivers/media/pci/pt3/Kconfig"
source "drivers/media/pci/mantis/Kconfig"
+source "drivers/media/pci/netup_unidvb/Kconfig"
source "drivers/media/pci/ngene/Kconfig"
-source "drivers/media/pci/ddbridge/Kconfig"
+source "drivers/media/pci/pluto2/Kconfig"
+source "drivers/media/pci/pt1/Kconfig"
+source "drivers/media/pci/pt3/Kconfig"
source "drivers/media/pci/smipcie/Kconfig"
-source "drivers/media/pci/netup_unidvb/Kconfig"
-endif
+source "drivers/media/pci/ttpci/Kconfig"
-source "drivers/media/pci/intel/ipu3/Kconfig"
+endif
config VIDEO_PCI_SKELETON
tristate "Skeleton PCI V4L2 driver"
@@ -68,5 +73,7 @@ config VIDEO_PCI_SKELETON
Enable build of the skeleton PCI driver, used as a reference
when developing new drivers.
+source "drivers/media/pci/intel/ipu3/Kconfig"
+
endif #MEDIA_PCI_SUPPORT
endif #PCI
diff --git a/drivers/media/radio/Kconfig b/drivers/media/radio/Kconfig
index 58c10a2ed292..cca03bd2cc42 100644
--- a/drivers/media/radio/Kconfig
+++ b/drivers/media/radio/Kconfig
@@ -13,57 +13,6 @@ menuconfig RADIO_ADAPTERS
if RADIO_ADAPTERS
-config RADIO_TEA575X
- tristate
-
-source "drivers/media/radio/si470x/Kconfig"
-
-config RADIO_SI4713
- tristate "Silicon Labs Si4713 FM Radio with RDS Transmitter support"
-
-source "drivers/media/radio/si4713/Kconfig"
-
-config RADIO_SI476X
- tristate "Silicon Laboratories Si476x I2C FM Radio"
- depends on I2C
- depends on MFD_SI476X_CORE
- depends on SND_SOC
- select SND_SOC_SI476X
- help
- Choose Y here if you have this FM radio chip.
-
- In order to control your radio card, you will need to use programs
- that are compatible with the Video For Linux 2 API. Information on
- this API and pointers to "v4l2" programs may be found at
- <file:Documentation/userspace-api/media/index.rst>.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-si476x.
-
-config USB_MR800
- tristate "AverMedia MR 800 USB FM radio support"
- depends on USB
- help
- Say Y here if you want to connect this type of radio to your
- computer's USB port. Note that the audio is not digital, and
- you must connect the line out connector to a sound card or a
- set of speakers.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-mr800.
-
-config USB_DSBR
- tristate "D-Link/GemTek USB FM radio support"
- depends on USB
- help
- Say Y here if you want to connect this type of radio to your
- computer's USB port. Note that the audio is not digital, and
- you must connect the line out connector to a sound card or a
- set of speakers.
-
- To compile this driver as a module, choose M here: the
- module will be called dsbr100.
-
config RADIO_MAXIRADIO
tristate "Guillemot MAXI Radio FM 2000 radio"
depends on PCI
@@ -80,6 +29,18 @@ config RADIO_MAXIRADIO
To compile this driver as a module, choose M here: the
module will be called radio-maxiradio.
+config RADIO_SAA7706H
+ tristate "SAA7706H Car Radio DSP"
+ depends on I2C
+ help
+ Say Y here if you want to use the SAA7706H Car radio Digital
+ Signal Processor, found for instance on the Russellville development
+ board. On the russellville the device is connected to internal
+ timberdale I2C bus.
+
+ To compile this driver as a module, choose M here: the
+ module will be called SAA7706H.
+
config RADIO_SHARK
tristate "Griffin radioSHARK USB radio receiver"
depends on USB
@@ -115,41 +76,28 @@ config RADIO_SHARK2
To compile this driver as a module, choose M here: the
module will be called radio-shark2.
-config USB_KEENE
- tristate "Keene FM Transmitter USB support"
- depends on USB
- help
- Say Y here if you want to connect this type of FM transmitter
- to your computer's USB port.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-keene.
+config RADIO_SI4713
+ tristate "Silicon Labs Si4713 FM Radio with RDS Transmitter support"
-config USB_RAREMONO
- tristate "Thanko's Raremono AM/FM/SW radio support"
- depends on USB
+config RADIO_SI476X
+ tristate "Silicon Laboratories Si476x I2C FM Radio"
+ depends on I2C
+ depends on MFD_SI476X_CORE
+ depends on SND_SOC
+ select SND_SOC_SI476X
help
- The 'Thanko's Raremono' device contains the Si4734 chip from Silicon Labs Inc.
- It is one of the very few or perhaps the only consumer USB radio device
- to receive the AM/FM/SW bands.
+ Choose Y here if you have this FM radio chip.
- Say Y here if you want to connect this type of AM/FM/SW receiver
- to your computer's USB port.
+ In order to control your radio card, you will need to use programs
+ that are compatible with the Video For Linux 2 API. Information on
+ this API and pointers to "v4l2" programs may be found at
+ <file:Documentation/userspace-api/media/index.rst>.
To compile this driver as a module, choose M here: the
- module will be called radio-raremono.
+ module will be called radio-si476x.
-config USB_MA901
- tristate "Masterkit MA901 USB FM radio support"
- depends on USB
- help
- Say Y here if you want to connect this type of radio to your
- computer's USB port. Note that the audio is not digital, and
- you must connect the line out connector to a sound card or a
- set of speakers or headphones.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-ma901.
+config RADIO_TEA575X
+ tristate
config RADIO_TEA5764
tristate "TEA5764 I2C FM radio support"
@@ -170,18 +118,6 @@ config RADIO_TEA5764_XTAL
Say Y here if TEA5764 have a 32768 Hz crystal in circuit, say N
here if TEA5764 reference frequency is connected in FREQIN.
-config RADIO_SAA7706H
- tristate "SAA7706H Car Radio DSP"
- depends on I2C
- help
- Say Y here if you want to use the SAA7706H Car radio Digital
- Signal Processor, found for instance on the Russellville development
- board. On the russellville the device is connected to internal
- timberdale I2C bus.
-
- To compile this driver as a module, choose M here: the
- module will be called SAA7706H.
-
config RADIO_TEF6862
tristate "TEF6862 Car Radio Enhanced Selectivity Tuner"
depends on I2C
@@ -222,7 +158,71 @@ config RADIO_WL1273
To compile this driver as a module, choose M here: the
module will be called radio-wl1273.
+config USB_DSBR
+ tristate "D-Link/GemTek USB FM radio support"
+ depends on USB
+ help
+ Say Y here if you want to connect this type of radio to your
+ computer's USB port. Note that the audio is not digital, and
+ you must connect the line out connector to a sound card or a
+ set of speakers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called dsbr100.
+
+config USB_KEENE
+ tristate "Keene FM Transmitter USB support"
+ depends on USB
+ help
+ Say Y here if you want to connect this type of FM transmitter
+ to your computer's USB port.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-keene.
+
+config USB_MA901
+ tristate "Masterkit MA901 USB FM radio support"
+ depends on USB
+ help
+ Say Y here if you want to connect this type of radio to your
+ computer's USB port. Note that the audio is not digital, and
+ you must connect the line out connector to a sound card or a
+ set of speakers or headphones.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-ma901.
+
+config USB_MR800
+ tristate "AverMedia MR 800 USB FM radio support"
+ depends on USB
+ help
+ Say Y here if you want to connect this type of radio to your
+ computer's USB port. Note that the audio is not digital, and
+ you must connect the line out connector to a sound card or a
+ set of speakers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-mr800.
+
+config USB_RAREMONO
+ tristate "Thanko's Raremono AM/FM/SW radio support"
+ depends on USB
+ help
+ The 'Thanko's Raremono' device contains the Si4734 chip from Silicon Labs Inc.
+ It is one of the very few or perhaps the only consumer USB radio device
+ to receive the AM/FM/SW bands.
+
+ Say Y here if you want to connect this type of AM/FM/SW receiver
+ to your computer's USB port.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-raremono.
+
+source "drivers/media/radio/si470x/Kconfig"
+source "drivers/media/radio/si4713/Kconfig"
+
# TI's ST based wl128x FM radio
+
source "drivers/media/radio/wl128x/Kconfig"
#
@@ -237,74 +237,6 @@ menuconfig V4L_RADIO_ISA_DRIVERS
if V4L_RADIO_ISA_DRIVERS
-config RADIO_ISA
- depends on ISA || COMPILE_TEST
- tristate
-
-config RADIO_CADET
- tristate "ADS Cadet AM/FM Tuner"
- depends on ISA || COMPILE_TEST
- help
- Choose Y here if you have one of these AM/FM radio cards, and then
- fill in the port address below.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-cadet.
-
-config RADIO_RTRACK
- tristate "AIMSlab RadioTrack (aka RadioReveal) support"
- depends on ISA || COMPILE_TEST
- select RADIO_ISA
- help
- Choose Y here if you have one of these FM radio cards, and then fill
- in the port address below.
-
- Note that newer AIMSlab RadioTrack cards have a different chipset
- and are not supported by this driver. For these cards, use the
- RadioTrack II driver below.
-
- If you have a GemTeks combined (PnP) sound- and radio card you must
- use this driver as a module and setup the card with isapnptools.
- You must also pass the module a suitable io parameter, 0x248 has
- been reported to be used by these cards.
-
- More information is contained in the file
- <file:Documentation/driver-api/media/drivers/radiotrack.rst>.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-aimslab.
-
-config RADIO_RTRACK_PORT
- hex "RadioTrack i/o port (0x20f or 0x30f)"
- depends on RADIO_RTRACK=y
- default "30f"
- help
- Enter either 0x30f or 0x20f here. The card default is 0x30f, if you
- haven't changed the jumper setting on the card.
-
-config RADIO_RTRACK2
- tristate "AIMSlab RadioTrack II support"
- depends on ISA || COMPILE_TEST
- select RADIO_ISA
- help
- Choose Y here if you have this FM radio card, and then fill in the
- port address below.
-
- Note: this driver hasn't been tested since a long time due to lack
- of hardware. If you have this hardware, then please contact the
- linux-media mailinglist.
-
- To compile this driver as a module, choose M here: the
- module will be called radio-rtrack2.
-
-config RADIO_RTRACK2_PORT
- hex "RadioTrack II i/o port (0x20c or 0x30c)"
- depends on RADIO_RTRACK2=y
- default "30c"
- help
- Enter either 0x30c or 0x20c here. The card default is 0x30c, if you
- haven't changed the jumper setting on the card.
-
config RADIO_AZTECH
tristate "Aztech/Packard Bell Radio"
depends on ISA || COMPILE_TEST
@@ -325,6 +257,16 @@ config RADIO_AZTECH_PORT
haven't changed the setting of jumper JP3 on the card. Removing the
jumper sets the card to 0x358.
+config RADIO_CADET
+ tristate "ADS Cadet AM/FM Tuner"
+ depends on ISA || COMPILE_TEST
+ help
+ Choose Y here if you have one of these AM/FM radio cards, and then
+ fill in the port address below.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-cadet.
+
config RADIO_GEMTEK
tristate "GemTek Radio card (or compatible) support"
depends on ISA || COMPILE_TEST
@@ -365,6 +307,10 @@ config RADIO_GEMTEK_PROBE
following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and
0x28c.
+config RADIO_ISA
+ depends on ISA || COMPILE_TEST
+ tristate
+
config RADIO_MIROPCM20
tristate "miroSOUND PCM20 radio"
depends on ISA || COMPILE_TEST
@@ -380,6 +326,60 @@ config RADIO_MIROPCM20
To compile this driver as a module, choose M here: the
module will be called radio-miropcm20.
+config RADIO_RTRACK
+ tristate "AIMSlab RadioTrack (aka RadioReveal) support"
+ depends on ISA || COMPILE_TEST
+ select RADIO_ISA
+ help
+ Choose Y here if you have one of these FM radio cards, and then fill
+ in the port address below.
+
+ Note that newer AIMSlab RadioTrack cards have a different chipset
+ and are not supported by this driver. For these cards, use the
+ RadioTrack II driver below.
+
+ If you have a GemTeks combined (PnP) sound- and radio card you must
+ use this driver as a module and setup the card with isapnptools.
+ You must also pass the module a suitable io parameter, 0x248 has
+ been reported to be used by these cards.
+
+ More information is contained in the file
+ <file:Documentation/driver-api/media/drivers/radiotrack.rst>.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-aimslab.
+
+config RADIO_RTRACK2
+ tristate "AIMSlab RadioTrack II support"
+ depends on ISA || COMPILE_TEST
+ select RADIO_ISA
+ help
+ Choose Y here if you have this FM radio card, and then fill in the
+ port address below.
+
+ Note: this driver hasn't been tested since a long time due to lack
+ of hardware. If you have this hardware, then please contact the
+ linux-media mailinglist.
+
+ To compile this driver as a module, choose M here: the
+ module will be called radio-rtrack2.
+
+config RADIO_RTRACK2_PORT
+ hex "RadioTrack II i/o port (0x20c or 0x30c)"
+ depends on RADIO_RTRACK2=y
+ default "30c"
+ help
+ Enter either 0x30c or 0x20c here. The card default is 0x30c, if you
+ haven't changed the jumper setting on the card.
+
+config RADIO_RTRACK_PORT
+ hex "RadioTrack i/o port (0x20f or 0x30f)"
+ depends on RADIO_RTRACK=y
+ default "30f"
+ help
+ Enter either 0x30f or 0x20f here. The card default is 0x30f, if you
+ haven't changed the jumper setting on the card.
+
config RADIO_SF16FMI
tristate "SF16-FMI/SF16-FMP/SF16-FMD Radio"
depends on ISA || COMPILE_TEST
@@ -451,13 +451,6 @@ config RADIO_TYPHOON
To compile this driver as a module, choose M here: the
module will be called radio-typhoon.
-config RADIO_TYPHOON_PORT
- hex "Typhoon I/O port (0x316 or 0x336)"
- depends on RADIO_TYPHOON=y
- default "316"
- help
- Enter the I/O port of your Typhoon or EcoRadio radio card.
-
config RADIO_TYPHOON_MUTEFREQ
int "Typhoon frequency set when muting the device (kHz)"
depends on RADIO_TYPHOON=y
@@ -470,6 +463,13 @@ config RADIO_TYPHOON_MUTEFREQ
the device is muted. There should be no local radio station at that
frequency.
+config RADIO_TYPHOON_PORT
+ hex "Typhoon I/O port (0x316 or 0x336)"
+ depends on RADIO_TYPHOON=y
+ default "316"
+ help
+ Enter the I/O port of your Typhoon or EcoRadio radio card.
+
config RADIO_ZOLTRIX
tristate "Zoltrix Radio"
depends on ISA || COMPILE_TEST
diff --git a/drivers/media/rc/Kconfig b/drivers/media/rc/Kconfig
index c111af820ae4..f560fc38895f 100644
--- a/drivers/media/rc/Kconfig
+++ b/drivers/media/rc/Kconfig
@@ -15,15 +15,6 @@ menuconfig RC_CORE
Say Y when you have a TV or an IR device.
if RC_CORE
-source "drivers/media/rc/keymaps/Kconfig"
-
-config LIRC
- bool "LIRC user interface"
- help
- Enable this option to enable the Linux Infrared Remote
- Control user interface (e.g. /dev/lirc*). This interface
- passes raw IR to and from userspace, which is needed for
- IR transmitting (aka "blasting") and for the lirc daemon.
config BPF_LIRC_MODE2
bool "Support for eBPF programs attached to lirc devices"
@@ -38,10 +29,45 @@ config BPF_LIRC_MODE2
These eBPF programs can be used to decode IR into scancodes, for
IR protocols not supported by the kernel decoders.
+config LIRC
+ bool "LIRC user interface"
+ help
+ Enable this option to enable the Linux Infrared Remote
+ Control user interface (e.g. /dev/lirc*). This interface
+ passes raw IR to and from userspace, which is needed for
+ IR transmitting (aka "blasting") and for the lirc daemon.
+
+source "drivers/media/rc/keymaps/Kconfig"
+
menuconfig RC_DECODERS
bool "Remote controller decoders"
if RC_DECODERS
+
+config IR_IMON_DECODER
+ tristate "Enable IR raw decoder for the iMON protocol"
+ help
+ Enable this option if you have iMON PAD or Antec Veris infrared
+ remote control and you would like to use it with a raw IR
+ receiver, or if you wish to use an encoder to transmit this IR.
+
+config IR_JVC_DECODER
+ tristate "Enable IR raw decoder for the JVC protocol"
+ select BITREVERSE
+
+ help
+ Enable this option if you have an infrared remote control which
+ uses the JVC protocol, and you need software decoding support.
+
+config IR_MCE_KBD_DECODER
+ tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
+ select BITREVERSE
+
+ help
+ Enable this option if you have a Microsoft Remote Keyboard for
+ Windows Media Center Edition, which you would like to use with
+ a raw IR receiver in your system.
+
config IR_NEC_DECODER
tristate "Enable IR raw decoder for the NEC protocol"
select BITREVERSE
@@ -66,21 +92,17 @@ config IR_RC6_DECODER
Enable this option if you have an infrared remote control which
uses the RC6 protocol, and you need software decoding support.
-config IR_JVC_DECODER
- tristate "Enable IR raw decoder for the JVC protocol"
- select BITREVERSE
-
+config IR_RCMM_DECODER
+ tristate "Enable IR raw decoder for the RC-MM protocol"
help
- Enable this option if you have an infrared remote control which
- uses the JVC protocol, and you need software decoding support.
-
-config IR_SONY_DECODER
- tristate "Enable IR raw decoder for the Sony protocol"
- select BITREVERSE
+ Enable this option when you have IR with RC-MM protocol, and
+ you need the software decoder. The driver supports 12,
+ 24 and 32 bits RC-MM variants. You can enable or disable the
+ different modes using the following RC protocol keywords:
+ 'rc-mm-12', 'rc-mm-24' and 'rc-mm-32'.
- help
- Enable this option if you have an infrared remote control which
- uses the Sony protocol, and you need software decoding support.
+ To compile this driver as a module, choose M here: the module
+ will be called ir-rcmm-decoder.
config IR_SANYO_DECODER
tristate "Enable IR raw decoder for the Sanyo protocol"
@@ -100,14 +122,13 @@ config IR_SHARP_DECODER
uses the Sharp protocol (Sharp, Denon), and you need software
decoding support.
-config IR_MCE_KBD_DECODER
- tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
+config IR_SONY_DECODER
+ tristate "Enable IR raw decoder for the Sony protocol"
select BITREVERSE
help
- Enable this option if you have a Microsoft Remote Keyboard for
- Windows Media Center Edition, which you would like to use with
- a raw IR receiver in your system.
+ Enable this option if you have an infrared remote control which
+ uses the Sony protocol, and you need software decoding support.
config IR_XMP_DECODER
tristate "Enable IR raw decoder for the XMP protocol"
@@ -117,25 +138,6 @@ config IR_XMP_DECODER
Enable this option if you have IR with XMP protocol, and
if the IR is decoded in software
-config IR_IMON_DECODER
- tristate "Enable IR raw decoder for the iMON protocol"
- help
- Enable this option if you have iMON PAD or Antec Veris infrared
- remote control and you would like to use it with a raw IR
- receiver, or if you wish to use an encoder to transmit this IR.
-
-config IR_RCMM_DECODER
- tristate "Enable IR raw decoder for the RC-MM protocol"
- help
- Enable this option when you have IR with RC-MM protocol, and
- you need the software decoder. The driver supports 12,
- 24 and 32 bits RC-MM variants. You can enable or disable the
- different modes using the following RC protocol keywords:
- 'rc-mm-12', 'rc-mm-24' and 'rc-mm-32'.
-
- To compile this driver as a module, choose M here: the module
- will be called ir-rcmm-decoder.
-
endif #RC_DECODERS
menuconfig RC_DEVICES
@@ -143,23 +145,6 @@ menuconfig RC_DEVICES
if RC_DEVICES
-config RC_ATI_REMOTE
- tristate "ATI / X10 based USB RF remote controls"
- depends on USB
- help
- Say Y here if you want to use an X10 based USB remote control.
- These are RF remotes with USB receivers.
-
- Such devices include the ATI remote that comes with many of ATI's
- All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote,
- Medion RF remote, and SnapStream FireFly remote.
-
- This driver provides mouse pointer, left and right mouse buttons,
- and maps all the other remote buttons to keypress events.
-
- To compile this driver as a module, choose M here: the module will be
- called ati_remote.
-
config IR_ENE
tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
depends on PNP || COMPILE_TEST
@@ -173,6 +158,37 @@ config IR_ENE
To compile this driver as a module, choose M here: the
module will be called ene_ir.
+config IR_FINTEK
+ tristate "Fintek Consumer Infrared Transceiver"
+ depends on PNP || COMPILE_TEST
+ help
+ Say Y here to enable support for integrated infrared receiver
+ /transceiver made by Fintek. This chip is found on assorted
+ Jetway motherboards (and of course, possibly others).
+
+ To compile this driver as a module, choose M here: the
+ module will be called fintek-cir.
+
+config IR_GPIO_CIR
+ tristate "GPIO IR remote control"
+ depends on (OF && GPIOLIB) || COMPILE_TEST
+ help
+ Say Y if you want to use GPIO based IR Receiver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called gpio-ir-recv.
+
+config IR_GPIO_TX
+ tristate "GPIO IR Bit Banging Transmitter"
+ depends on LIRC
+ depends on (OF && GPIOLIB) || COMPILE_TEST
+ help
+ Say Y if you want to a GPIO based IR transmitter. This is a
+ bit banging driver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called gpio-ir-tx.
+
config IR_HIX5HD2
tristate "Hisilicon hix5hd2 IR remote control"
depends on (OF && HAS_IOMEM) || COMPILE_TEST
@@ -183,6 +199,33 @@ config IR_HIX5HD2
If you're not sure, select N here
+config IR_IGORPLUGUSB
+ tristate "IgorPlug-USB IR Receiver"
+ depends on USB
+ help
+ Say Y here if you want to use the IgorPlug-USB IR Receiver by
+ Igor Cesko. This device is included on the Fit-PC2.
+
+ Note that this device can only record bursts of 36 IR pulses and
+ spaces, which is not enough for the NEC, Sanyo and RC-6 protocol.
+
+ To compile this driver as a module, choose M here: the module will
+ be called igorplugusb.
+
+config IR_IGUANA
+ tristate "IguanaWorks USB IR Transceiver"
+ depends on USB
+ help
+ Say Y here if you want to use the IguanaWorks USB IR Transceiver.
+ Both infrared receive and send are supported. If you want to
+ change the ID or the pin config, use the user space driver from
+ IguanaWorks.
+
+ Only firmware 0x0205 and later is supported.
+
+ To compile this driver as a module, choose M here: the module will
+ be called iguanair.
+
config IR_IMON
tristate "SoundGraph iMON Receiver and Display"
depends on USB
@@ -203,16 +246,6 @@ config IR_IMON_RAW
To compile this driver as a module, choose M here: the
module will be called imon_raw.
-config IR_MCEUSB
- tristate "Windows Media Center Ed. eHome Infrared Transceiver"
- depends on USB
- help
- Say Y here if you want to use a Windows Media Center Edition
- eHome Infrared Transceiver.
-
- To compile this driver as a module, choose M here: the
- module will be called mceusb.
-
config IR_ITE_CIR
tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
depends on PNP || COMPILE_TEST
@@ -225,16 +258,15 @@ config IR_ITE_CIR
To compile this driver as a module, choose M here: the
module will be called ite-cir.
-config IR_FINTEK
- tristate "Fintek Consumer Infrared Transceiver"
- depends on PNP || COMPILE_TEST
+config IR_MCEUSB
+ tristate "Windows Media Center Ed. eHome Infrared Transceiver"
+ depends on USB
help
- Say Y here to enable support for integrated infrared receiver
- /transceiver made by Fintek. This chip is found on assorted
- Jetway motherboards (and of course, possibly others).
+ Say Y here if you want to use a Windows Media Center Edition
+ eHome Infrared Transceiver.
To compile this driver as a module, choose M here: the
- module will be called fintek-cir.
+ module will be called mceusb.
config IR_MESON
tristate "Amlogic Meson IR remote receiver"
@@ -278,6 +310,18 @@ config IR_NUVOTON
To compile this driver as a module, choose M here: the
module will be called nuvoton-cir.
+config IR_PWM_TX
+ tristate "PWM IR transmitter"
+ depends on LIRC
+ depends on PWM
+ depends on OF || COMPILE_TEST
+ help
+ Say Y if you want to use a PWM based IR transmitter. This is
+ more power efficient than the bit banging gpio driver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called pwm-ir-tx.
+
config IR_REDRAT3
tristate "RedRat3 IR Transceiver"
depends on USB
@@ -289,6 +333,31 @@ config IR_REDRAT3
To compile this driver as a module, choose M here: the
module will be called redrat3.
+config IR_RX51
+ tristate "Nokia N900 IR transmitter diode"
+ depends on (OMAP_DM_TIMER && PWM_OMAP_DMTIMER && ARCH_OMAP2PLUS || COMPILE_TEST) && RC_CORE
+ help
+ Say Y or M here if you want to enable support for the IR
+ transmitter diode built in the Nokia N900 (RX51) device.
+
+ The driver uses omap DM timers for generating the carrier
+ wave and pulses.
+
+config IR_SERIAL
+ tristate "Homebrew Serial Port Receiver"
+ help
+ Say Y if you want to use Homebrew Serial Port Receivers and
+ Transceivers.
+
+ To compile this driver as a module, choose M here: the module will
+ be called serial-ir.
+
+config IR_SERIAL_TRANSMITTER
+ bool "Serial Port Transmitter"
+ depends on IR_SERIAL
+ help
+ Serial Port Transmitter support
+
config IR_SPI
tristate "SPI connected IR LED"
depends on SPI && LIRC
@@ -309,6 +378,37 @@ config IR_STREAMZAP
To compile this driver as a module, choose M here: the
module will be called streamzap.
+config IR_SUNXI
+ tristate "SUNXI IR remote control"
+ depends on ARCH_SUNXI || COMPILE_TEST
+ help
+ Say Y if you want to use sunXi internal IR Controller
+
+ To compile this driver as a module, choose M here: the module will
+ be called sunxi-ir.
+
+config IR_TOY
+ tristate "Infrared Toy and IR Droid"
+ depends on USB
+ help
+ Say Y here if you want to use the Infrared Toy or IR Droid, USB
+ versions.
+
+ To compile this driver as a module, choose M here: the module will be
+ called ir_toy.
+
+config IR_TTUSBIR
+ tristate "TechnoTrend USB IR Receiver"
+ depends on USB
+ select NEW_LEDS
+ select LEDS_CLASS
+ help
+ Say Y here if you want to use the TechnoTrend USB IR Receiver. The
+ driver can control the led.
+
+ To compile this driver as a module, choose M here: the module will
+ be called ttusbir.
+
config IR_WINBOND_CIR
tristate "Winbond IR remote control"
depends on (X86 && PNP) || COMPILE_TEST
@@ -324,56 +424,22 @@ config IR_WINBOND_CIR
To compile this driver as a module, choose M here: the module will
be called winbond_cir.
-config IR_IGORPLUGUSB
- tristate "IgorPlug-USB IR Receiver"
+config RC_ATI_REMOTE
+ tristate "ATI / X10 based USB RF remote controls"
depends on USB
help
- Say Y here if you want to use the IgorPlug-USB IR Receiver by
- Igor Cesko. This device is included on the Fit-PC2.
+ Say Y here if you want to use an X10 based USB remote control.
+ These are RF remotes with USB receivers.
- Note that this device can only record bursts of 36 IR pulses and
- spaces, which is not enough for the NEC, Sanyo and RC-6 protocol.
+ Such devices include the ATI remote that comes with many of ATI's
+ All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote,
+ Medion RF remote, and SnapStream FireFly remote.
- To compile this driver as a module, choose M here: the module will
- be called igorplugusb.
+ This driver provides mouse pointer, left and right mouse buttons,
+ and maps all the other remote buttons to keypress events.
-config IR_IGUANA
- tristate "IguanaWorks USB IR Transceiver"
- depends on USB
- help
- Say Y here if you want to use the IguanaWorks USB IR Transceiver.
- Both infrared receive and send are supported. If you want to
- change the ID or the pin config, use the user space driver from
- IguanaWorks.
-
- Only firmware 0x0205 and later is supported.
-
- To compile this driver as a module, choose M here: the module will
- be called iguanair.
-
-config IR_TTUSBIR
- tristate "TechnoTrend USB IR Receiver"
- depends on USB
- select NEW_LEDS
- select LEDS_CLASS
- help
- Say Y here if you want to use the TechnoTrend USB IR Receiver. The
- driver can control the led.
-
- To compile this driver as a module, choose M here: the module will
- be called ttusbir.
-
-config IR_RX51
- tristate "Nokia N900 IR transmitter diode"
- depends on (OMAP_DM_TIMER && PWM_OMAP_DMTIMER && ARCH_OMAP2PLUS || COMPILE_TEST) && RC_CORE
- help
- Say Y or M here if you want to enable support for the IR
- transmitter diode built in the Nokia N900 (RX51) device.
-
- The driver uses omap DM timers for generating the carrier
- wave and pulses.
-
-source "drivers/media/rc/img-ir/Kconfig"
+ To compile this driver as a module, choose M here: the module will be
+ called ati_remote.
config RC_LOOPBACK
tristate "Remote Control Loopback Driver"
@@ -387,38 +453,6 @@ config RC_LOOPBACK
To compile this driver as a module, choose M here: the module will
be called rc_loopback.
-config IR_GPIO_CIR
- tristate "GPIO IR remote control"
- depends on (OF && GPIOLIB) || COMPILE_TEST
- help
- Say Y if you want to use GPIO based IR Receiver.
-
- To compile this driver as a module, choose M here: the module will
- be called gpio-ir-recv.
-
-config IR_GPIO_TX
- tristate "GPIO IR Bit Banging Transmitter"
- depends on LIRC
- depends on (OF && GPIOLIB) || COMPILE_TEST
- help
- Say Y if you want to a GPIO based IR transmitter. This is a
- bit banging driver.
-
- To compile this driver as a module, choose M here: the module will
- be called gpio-ir-tx.
-
-config IR_PWM_TX
- tristate "PWM IR transmitter"
- depends on LIRC
- depends on PWM
- depends on OF || COMPILE_TEST
- help
- Say Y if you want to use a PWM based IR transmitter. This is
- more power efficient than the bit banging gpio driver.
-
- To compile this driver as a module, choose M here: the module will
- be called pwm-ir-tx.
-
config RC_ST
tristate "ST remote control receiver"
depends on ARCH_STI || COMPILE_TEST
@@ -429,30 +463,6 @@ config RC_ST
If you're not sure, select N here.
-config IR_SUNXI
- tristate "SUNXI IR remote control"
- depends on ARCH_SUNXI || COMPILE_TEST
- help
- Say Y if you want to use sunXi internal IR Controller
-
- To compile this driver as a module, choose M here: the module will
- be called sunxi-ir.
-
-config IR_SERIAL
- tristate "Homebrew Serial Port Receiver"
- help
- Say Y if you want to use Homebrew Serial Port Receivers and
- Transceivers.
-
- To compile this driver as a module, choose M here: the module will
- be called serial-ir.
-
-config IR_SERIAL_TRANSMITTER
- bool "Serial Port Transmitter"
- depends on IR_SERIAL
- help
- Serial Port Transmitter support
-
config RC_XBOX_DVD
tristate "Xbox DVD Movie Playback Kit"
depends on USB
@@ -463,15 +473,7 @@ config RC_XBOX_DVD
To compile this driver as a module, choose M here: the module will be
called xbox_remote.
-config IR_TOY
- tristate "Infrared Toy and IR Droid"
- depends on USB
- help
- Say Y here if you want to use the Infrared Toy or IR Droid, USB
- versions.
-
- To compile this driver as a module, choose M here: the module will be
- called ir_toy.
+source "drivers/media/rc/img-ir/Kconfig"
endif #RC_DEVICES
diff --git a/drivers/media/test-drivers/Kconfig b/drivers/media/test-drivers/Kconfig
index d663d822ec75..51cf27834df0 100644
--- a/drivers/media/test-drivers/Kconfig
+++ b/drivers/media/test-drivers/Kconfig
@@ -6,10 +6,6 @@ menuconfig V4L_TEST_DRIVERS
if V4L_TEST_DRIVERS
-source "drivers/media/test-drivers/vimc/Kconfig"
-
-source "drivers/media/test-drivers/vivid/Kconfig"
-
config VIDEO_VIM2M
tristate "Virtual Memory-to-Memory Driver"
depends on VIDEO_DEV
@@ -22,6 +18,8 @@ config VIDEO_VIM2M
framework.
source "drivers/media/test-drivers/vicodec/Kconfig"
+source "drivers/media/test-drivers/vimc/Kconfig"
+source "drivers/media/test-drivers/vivid/Kconfig"
endif #V4L_TEST_DRIVERS
diff --git a/drivers/media/test-drivers/vidtv/Kconfig b/drivers/media/test-drivers/vidtv/Kconfig
index 22c4fd39461f..e511e51c0b5b 100644
--- a/drivers/media/test-drivers/vidtv/Kconfig
+++ b/drivers/media/test-drivers/vidtv/Kconfig
@@ -7,5 +7,4 @@ config DVB_VIDTV
validate the existing APIs in the media subsystem. It can also aid developers
working on userspace applications.
-
When in doubt, say N.
diff --git a/drivers/media/tuners/Kconfig b/drivers/media/tuners/Kconfig
index 81d1d56b9317..0c01b0298099 100644
--- a/drivers/media/tuners/Kconfig
+++ b/drivers/media/tuners/Kconfig
@@ -23,6 +23,172 @@ menu "Customize TV tuners"
visible if !MEDIA_HIDE_ANCILLARY_SUBDRV
depends on MEDIA_ANALOG_TV_SUPPORT || MEDIA_DIGITAL_TV_SUPPORT || MEDIA_RADIO_SUPPORT || MEDIA_SDR_SUPPORT
+config MEDIA_TUNER_E4000
+ tristate "Elonics E4000 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C && VIDEO_DEV
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Elonics E4000 silicon tuner driver.
+
+config MEDIA_TUNER_FC0011
+ tristate "Fitipower FC0011 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Fitipower FC0011 silicon tuner driver.
+
+config MEDIA_TUNER_FC0012
+ tristate "Fitipower FC0012 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Fitipower FC0012 silicon tuner driver.
+
+config MEDIA_TUNER_FC0013
+ tristate "Fitipower FC0013 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Fitipower FC0013 silicon tuner driver.
+
+config MEDIA_TUNER_FC2580
+ tristate "FCI FC2580 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C && VIDEO_DEV
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ FCI FC2580 silicon tuner driver.
+
+config MEDIA_TUNER_IT913X
+ tristate "ITE Tech IT913x silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ ITE Tech IT913x silicon tuner driver.
+
+config MEDIA_TUNER_M88RS6000T
+ tristate "Montage M88RS6000 internal tuner"
+ depends on MEDIA_SUPPORT && I2C
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Montage M88RS6000 internal tuner.
+
+config MEDIA_TUNER_MAX2165
+ tristate "Maxim MAX2165 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon tuner MAX2165 from Maxim.
+
+config MEDIA_TUNER_MC44S803
+ tristate "Freescale MC44S803 Low Power CMOS Broadband tuners"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to support the Freescale MC44S803 based tuners
+
+config MEDIA_TUNER_MSI001
+ tristate "Mirics MSi001"
+ depends on MEDIA_SUPPORT && SPI && VIDEO_DEV
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Mirics MSi001 silicon tuner driver.
+
+config MEDIA_TUNER_MT2060
+ tristate "Microtune MT2060 silicon IF tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon IF tuner MT2060 from Microtune.
+
+config MEDIA_TUNER_MT2063
+ tristate "Microtune MT2063 silicon IF tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon IF tuner MT2063 from Microtune.
+
+config MEDIA_TUNER_MT20XX
+ tristate "Microtune 2032 / 2050 tuners"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to include support for the MT2032 / MT2050 tuner.
+
+config MEDIA_TUNER_MT2131
+ tristate "Microtune MT2131 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon baseband tuner MT2131 from Microtune.
+
+config MEDIA_TUNER_MT2266
+ tristate "Microtune MT2266 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon baseband tuner MT2266 from Microtune.
+
+config MEDIA_TUNER_MXL301RF
+ tristate "MaxLinear MxL301RF tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ MaxLinear MxL301RF OFDM tuner driver.
+
+config MEDIA_TUNER_MXL5005S
+ tristate "MaxLinear MSL5005S silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon tuner MXL5005S from MaxLinear.
+
+config MEDIA_TUNER_MXL5007T
+ tristate "MaxLinear MxL5007T silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon tuner MxL5007T from MaxLinear.
+
+config MEDIA_TUNER_QM1D1B0004
+ tristate "Sharp QM1D1B0004 tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Sharp QM1D1B0004 ISDB-S tuner driver.
+
+config MEDIA_TUNER_QM1D1C0042
+ tristate "Sharp QM1D1C0042 tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Sharp QM1D1C0042 trellis coded 8PSK tuner driver.
+
+config MEDIA_TUNER_QT1010
+ tristate "Quantek QT1010 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A driver for the silicon tuner QT1010 from Quantek.
+
+config MEDIA_TUNER_R820T
+ tristate "Rafael Micro R820T silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ select BITREVERSE
+ help
+ Rafael Micro R820T silicon tuner driver.
+
+config MEDIA_TUNER_SI2157
+ tristate "Silicon Labs Si2157 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ Silicon Labs Si2157 silicon tuner driver.
+
config MEDIA_TUNER_SIMPLE
tristate "Simple tuner support"
depends on MEDIA_SUPPORT && I2C
@@ -31,6 +197,21 @@ config MEDIA_TUNER_SIMPLE
help
Say Y here to include support for various simple tuners.
+config MEDIA_TUNER_TDA18212
+ tristate "NXP TDA18212 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ select REGMAP_I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ NXP TDA18212 silicon tuner driver.
+
+config MEDIA_TUNER_TDA18218
+ tristate "NXP TDA18218 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ NXP TDA18218 silicon tuner driver.
+
config MEDIA_TUNER_TDA18250
tristate "NXP TDA18250 silicon tuner"
depends on MEDIA_SUPPORT && I2C
@@ -38,6 +219,20 @@ config MEDIA_TUNER_TDA18250
help
Say Y here to include support for TDA18250 tuner.
+config MEDIA_TUNER_TDA18271
+ tristate "NXP TDA18271 silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A silicon tuner module. Say Y when you want to support this tuner.
+
+config MEDIA_TUNER_TDA827X
+ tristate "Philips TDA827X silicon tuner"
+ depends on MEDIA_SUPPORT && I2C
+ default m if !MEDIA_SUBDRV_AUTOSELECT
+ help
+ A DVB-T silicon tuner module. Say Y when you want to support this tuner.
+
config MEDIA_TUNER_TDA8290
tristate "TDA 8290/8295 + 8275(a)/18271 tuner combo"
depends on MEDIA_SUPPORT && I2C
@@ -47,20 +242,6 @@ config MEDIA_TUNER_TDA8290
help
Say Y here to include support for Philips TDA8290+8275(a) tuner.
-config MEDIA_TUNER_TDA827X
- tristate "Philips TDA827X silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A DVB-T silicon tuner module. Say Y when you want to support this tuner.
-
-config MEDIA_TUNER_TDA18271
- tristate "NXP TDA18271 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A silicon tuner module. Say Y when you want to support this tuner.
-
config MEDIA_TUNER_TDA9887
tristate "TDA 9885/6/7 analog IF demodulator"
depends on MEDIA_SUPPORT && I2C
@@ -83,54 +264,13 @@ config MEDIA_TUNER_TEA5767
help
Say Y here to include support for the Philips TEA5767 radio tuner.
-config MEDIA_TUNER_MSI001
- tristate "Mirics MSi001"
- depends on MEDIA_SUPPORT && SPI && VIDEO_DEV
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Mirics MSi001 silicon tuner driver.
-
-config MEDIA_TUNER_MT20XX
- tristate "Microtune 2032 / 2050 tuners"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to include support for the MT2032 / MT2050 tuner.
-
-config MEDIA_TUNER_MT2060
- tristate "Microtune MT2060 silicon IF tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon IF tuner MT2060 from Microtune.
-
-config MEDIA_TUNER_MT2063
- tristate "Microtune MT2063 silicon IF tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon IF tuner MT2063 from Microtune.
-
-config MEDIA_TUNER_MT2266
- tristate "Microtune MT2266 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon baseband tuner MT2266 from Microtune.
-
-config MEDIA_TUNER_MT2131
- tristate "Microtune MT2131 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon baseband tuner MT2131 from Microtune.
-
-config MEDIA_TUNER_QT1010
- tristate "Quantek QT1010 silicon tuner"
+config MEDIA_TUNER_TUA9001
+ tristate "Infineon TUA9001 silicon tuner"
depends on MEDIA_SUPPORT && I2C
+ select REGMAP_I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A driver for the silicon tuner QT1010 from Quantek.
+ Infineon TUA 9001 silicon tuner driver.
config MEDIA_TUNER_XC2028
tristate "XCeive xc2028/xc3028 tuners"
@@ -139,15 +279,6 @@ config MEDIA_TUNER_XC2028
help
Say Y here to include support for the xc2028/xc3028 tuners.
-config MEDIA_TUNER_XC5000
- tristate "Xceive XC5000 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon tuner XC5000 from Xceive.
- This device is only used inside a SiP called together with a
- demodulator for now.
-
config MEDIA_TUNER_XC4000
tristate "Xceive XC4000 silicon tuner"
depends on MEDIA_SUPPORT && I2C
@@ -157,143 +288,13 @@ config MEDIA_TUNER_XC4000
This device is only used inside a SiP called together with a
demodulator for now.
-config MEDIA_TUNER_MXL5005S
- tristate "MaxLinear MSL5005S silicon tuner"
+config MEDIA_TUNER_XC5000
+ tristate "Xceive XC5000 silicon tuner"
depends on MEDIA_SUPPORT && I2C
default m if !MEDIA_SUBDRV_AUTOSELECT
help
- A driver for the silicon tuner MXL5005S from MaxLinear.
+ A driver for the silicon tuner XC5000 from Xceive.
+ This device is only used inside a SiP called together with a
+ demodulator for now.
-config MEDIA_TUNER_MXL5007T
- tristate "MaxLinear MxL5007T silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon tuner MxL5007T from MaxLinear.
-
-config MEDIA_TUNER_MC44S803
- tristate "Freescale MC44S803 Low Power CMOS Broadband tuners"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the Freescale MC44S803 based tuners
-
-config MEDIA_TUNER_MAX2165
- tristate "Maxim MAX2165 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- A driver for the silicon tuner MAX2165 from Maxim.
-
-config MEDIA_TUNER_TDA18218
- tristate "NXP TDA18218 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- NXP TDA18218 silicon tuner driver.
-
-config MEDIA_TUNER_FC0011
- tristate "Fitipower FC0011 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Fitipower FC0011 silicon tuner driver.
-
-config MEDIA_TUNER_FC0012
- tristate "Fitipower FC0012 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Fitipower FC0012 silicon tuner driver.
-
-config MEDIA_TUNER_FC0013
- tristate "Fitipower FC0013 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Fitipower FC0013 silicon tuner driver.
-
-config MEDIA_TUNER_TDA18212
- tristate "NXP TDA18212 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- NXP TDA18212 silicon tuner driver.
-
-config MEDIA_TUNER_E4000
- tristate "Elonics E4000 silicon tuner"
- depends on MEDIA_SUPPORT && I2C && VIDEO_DEV
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Elonics E4000 silicon tuner driver.
-
-config MEDIA_TUNER_FC2580
- tristate "FCI FC2580 silicon tuner"
- depends on MEDIA_SUPPORT && I2C && VIDEO_DEV
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- FCI FC2580 silicon tuner driver.
-
-config MEDIA_TUNER_M88RS6000T
- tristate "Montage M88RS6000 internal tuner"
- depends on MEDIA_SUPPORT && I2C
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Montage M88RS6000 internal tuner.
-
-config MEDIA_TUNER_TUA9001
- tristate "Infineon TUA9001 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Infineon TUA 9001 silicon tuner driver.
-
-config MEDIA_TUNER_SI2157
- tristate "Silicon Labs Si2157 silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Silicon Labs Si2157 silicon tuner driver.
-
-config MEDIA_TUNER_IT913X
- tristate "ITE Tech IT913x silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- select REGMAP_I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- ITE Tech IT913x silicon tuner driver.
-
-config MEDIA_TUNER_R820T
- tristate "Rafael Micro R820T silicon tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- select BITREVERSE
- help
- Rafael Micro R820T silicon tuner driver.
-
-config MEDIA_TUNER_MXL301RF
- tristate "MaxLinear MxL301RF tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- MaxLinear MxL301RF OFDM tuner driver.
-
-config MEDIA_TUNER_QM1D1C0042
- tristate "Sharp QM1D1C0042 tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Sharp QM1D1C0042 trellis coded 8PSK tuner driver.
-
-config MEDIA_TUNER_QM1D1B0004
- tristate "Sharp QM1D1B0004 tuner"
- depends on MEDIA_SUPPORT && I2C
- default m if !MEDIA_SUBDRV_AUTOSELECT
- help
- Sharp QM1D1B0004 ISDB-S tuner driver.
endmenu
diff --git a/drivers/media/usb/Kconfig b/drivers/media/usb/Kconfig
index f97153df3c84..8de08704f8e4 100644
--- a/drivers/media/usb/Kconfig
+++ b/drivers/media/usb/Kconfig
@@ -12,53 +12,64 @@ if MEDIA_USB_SUPPORT
if MEDIA_CAMERA_SUPPORT
comment "Webcam devices"
-source "drivers/media/usb/uvc/Kconfig"
+
+source "drivers/media/usb/cpia2/Kconfig"
source "drivers/media/usb/gspca/Kconfig"
source "drivers/media/usb/pwc/Kconfig"
-source "drivers/media/usb/cpia2/Kconfig"
-source "drivers/media/usb/zr364xx/Kconfig"
-source "drivers/media/usb/stkwebcam/Kconfig"
source "drivers/media/usb/s2255/Kconfig"
+source "drivers/media/usb/stkwebcam/Kconfig"
source "drivers/media/usb/usbtv/Kconfig"
+source "drivers/media/usb/uvc/Kconfig"
+source "drivers/media/usb/zr364xx/Kconfig"
+
endif
if MEDIA_ANALOG_TV_SUPPORT
comment "Analog TV USB devices"
-source "drivers/media/usb/pvrusb2/Kconfig"
+
+source "drivers/media/usb/go7007/Kconfig"
source "drivers/media/usb/hdpvr/Kconfig"
+source "drivers/media/usb/pvrusb2/Kconfig"
source "drivers/media/usb/stk1160/Kconfig"
-source "drivers/media/usb/go7007/Kconfig"
+
endif
if (MEDIA_ANALOG_TV_SUPPORT || MEDIA_DIGITAL_TV_SUPPORT)
comment "Analog/digital TV USB devices"
+
source "drivers/media/usb/au0828/Kconfig"
source "drivers/media/usb/cx231xx/Kconfig"
source "drivers/media/usb/tm6000/Kconfig"
-endif
+endif
if I2C && MEDIA_DIGITAL_TV_SUPPORT
comment "Digital TV USB devices"
-source "drivers/media/usb/dvb-usb/Kconfig"
+
+source "drivers/media/usb/as102/Kconfig"
+source "drivers/media/usb/b2c2/Kconfig"
source "drivers/media/usb/dvb-usb-v2/Kconfig"
+source "drivers/media/usb/dvb-usb/Kconfig"
+source "drivers/media/usb/siano/Kconfig"
source "drivers/media/usb/ttusb-budget/Kconfig"
source "drivers/media/usb/ttusb-dec/Kconfig"
-source "drivers/media/usb/siano/Kconfig"
-source "drivers/media/usb/b2c2/Kconfig"
-source "drivers/media/usb/as102/Kconfig"
+
endif
if (MEDIA_CAMERA_SUPPORT || MEDIA_ANALOG_TV_SUPPORT || MEDIA_DIGITAL_TV_SUPPORT)
comment "Webcam, TV (analog/digital) USB devices"
+
source "drivers/media/usb/em28xx/Kconfig"
+
endif
if MEDIA_SDR_SUPPORT
comment "Software defined radio USB devices"
+
source "drivers/media/usb/airspy/Kconfig"
source "drivers/media/usb/hackrf/Kconfig"
source "drivers/media/usb/msi2500/Kconfig"
+
endif
endif #MEDIA_USB_SUPPORT
diff --git a/drivers/media/usb/dvb-usb-v2/Kconfig b/drivers/media/usb/dvb-usb-v2/Kconfig
index a4600a97d1fd..4eadc9539b4c 100644
--- a/drivers/media/usb/dvb-usb-v2/Kconfig
+++ b/drivers/media/usb/dvb-usb-v2/Kconfig
@@ -14,6 +14,8 @@ config DVB_USB_V2
Say Y if you own a USB DVB device.
+if DVB_USB_V2
+
config DVB_USB_AF9015
tristate "Afatech AF9015 DVB-T USB2.0 support"
depends on DVB_USB_V2 && I2C_MUX
@@ -87,6 +89,17 @@ config DVB_USB_CE6230
help
Say Y here to support the Intel CE6230 DVB-T USB2.0 receiver
+config DVB_USB_DVBSKY
+ tristate "DVBSky USB support"
+ depends on DVB_USB_V2
+ select DVB_M88DS3103 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_SI2168 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TS2020 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_SI2157 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_SP2 if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to support the USB receivers from DVBSky.
+
config DVB_USB_EC168
tristate "E3C EC168 DVB-T USB2.0 support"
depends on DVB_USB_V2
@@ -154,17 +167,6 @@ config DVB_USB_RTL28XXU
help
Say Y here to support the Realtek RTL28xxU DVB USB receiver.
-config DVB_USB_DVBSKY
- tristate "DVBSky USB support"
- depends on DVB_USB_V2
- select DVB_M88DS3103 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_SI2168 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TS2020 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_SI2157 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_SP2 if MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the USB receivers from DVBSky.
-
config DVB_USB_ZD1301
tristate "ZyDAS ZD1301"
depends on DVB_USB_V2
@@ -172,3 +174,5 @@ config DVB_USB_ZD1301
select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
help
Say Y here to support the ZyDAS ZD1301 DVB USB receiver.
+
+endif
diff --git a/drivers/media/usb/dvb-usb/Kconfig b/drivers/media/usb/dvb-usb/Kconfig
index 6df96c2bf569..f10fe27e2a4d 100644
--- a/drivers/media/usb/dvb-usb/Kconfig
+++ b/drivers/media/usb/dvb-usb/Kconfig
@@ -22,15 +22,7 @@ config DVB_USB_DEBUG
Say Y if you want to enable debugging. See modinfo dvb-usb (and the
appropriate drivers) for debug levels.
-config DVB_USB_DIB3000MC
- tristate
- depends on DVB_USB
- select DVB_DIB3000MC
- help
- This is a module with helper functions for accessing the
- DIB3000MC from USB DVB devices. It must be a separate module
- in case DVB_USB is built-in and DVB_DIB3000MC is a module,
- and gets selected automatically when needed.
+if DVB_USB
config DVB_USB_A800
tristate "AVerMedia AverTV DVB-T USB 2.0 (A800)"
@@ -41,84 +33,37 @@ config DVB_USB_A800
help
Say Y here to support the AVerMedia AverTV DVB-T USB 2.0 (A800) receiver.
-config DVB_USB_DIBUSB_MB
- tristate "DiBcom USB DVB-T devices (based on the DiB3000M-B) (see help for device list)"
+config DVB_USB_AF9005
+ tristate "Afatech AF9005 DVB-T USB1.1 support"
depends on DVB_USB
- select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
- select DVB_DIB3000MB
- depends on DVB_DIB3000MC || !DVB_DIB3000MC
select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_QT1010 if MEDIA_SUBDRV_AUTOSELECT
help
- Support for USB 1.1 and 2.0 DVB-T receivers based on reference designs made by
- DiBcom (<http://www.dibcom.fr>) equipped with a DiB3000M-B demodulator.
+ Say Y here to support the Afatech AF9005 based DVB-T USB1.1 receiver
+ and the TerraTec Cinergy T USB XE (Rev.1)
- For an up-to-date list of devices supported by this driver, have a look
- on the Linux-DVB Wiki at www.linuxtv.org.
-
- Say Y if you own such a device and want to use it. You should build it as
- a module.
-
-config DVB_USB_DIBUSB_MB_FAULTY
- bool "Support faulty USB IDs"
- depends on DVB_USB_DIBUSB_MB
+config DVB_USB_AF9005_REMOTE
+ tristate "Afatech AF9005 default remote control support"
+ depends on DVB_USB_AF9005
help
- Support for faulty USB IDs due to an invalid EEPROM on some Artec devices.
+ Say Y here to support the default remote control decoding for the
+ Afatech AF9005 based receiver.
-config DVB_USB_DIBUSB_MC
- tristate "DiBcom USB DVB-T devices (based on the DiB3000M-C/P) (see help for device list)"
+config DVB_USB_AZ6027
+ tristate "Azurewave DVB-S/S2 USB2.0 AZ6027 support"
depends on DVB_USB
- select DVB_USB_DIB3000MC
- select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_STB0899 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_STB6100 if MEDIA_SUBDRV_AUTOSELECT
help
- Support for USB2.0 DVB-T receivers based on reference designs made by
- DiBcom (<http://www.dibcom.fr>) equipped with a DiB3000M-C/P demodulator.
+ Say Y here to support the AZ6027 device
- For an up-to-date list of devices supported by this driver, have a look
- on the Linux-DVB Wiki at www.linuxtv.org.
-
- Say Y if you own such a device and want to use it. You should build it as
- a module.
-
-config DVB_USB_DIB0700
- tristate "DiBcom DiB0700 USB DVB devices (see help for supported devices)"
+config DVB_USB_CINERGY_T2
+ tristate "Terratec CinergyT2/qanu USB 2.0 DVB-T receiver"
depends on DVB_USB
- select DVB_DIB7000P if MEDIA_SUBDRV_AUTOSELECT
- select DVB_DIB7000M if MEDIA_SUBDRV_AUTOSELECT
- select DVB_DIB8000 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_USB_DIB3000MC if MEDIA_SUBDRV_AUTOSELECT
- select DVB_S5H1411 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_LGDT3305 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_MN88472 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TUNER_DIB0070 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TUNER_DIB0090 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_MT2266 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_XC2028 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_XC5000 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_XC4000 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_MXL5007T if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_TDA18250 if MEDIA_SUBDRV_AUTOSELECT
help
- Support for USB2.0/1.1 DVB receivers based on the DiB0700 USB bridge. The
- USB bridge is also present in devices having the DiB7700 DVB-T-USB
- silicon. This chip can be found in devices offered by Hauppauge,
- Avermedia and other big and small companies.
+ Support for "TerraTec CinergyT2" USB2.0 Highspeed DVB Receivers
- For an up-to-date list of devices supported by this driver, have a look
- on the LinuxTV Wiki at www.linuxtv.org.
-
- Say Y if you own such a device and want to use it. You should build it as
- a module.
-
-config DVB_USB_UMT_010
- tristate "HanfTek UMT-010 DVB-T USB2.0 support"
- depends on DVB_USB
- select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
- select DVB_USB_DIB3000MC
- select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_MT352 if MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the HanfTek UMT-010 USB2.0 stick-sized DVB-T receiver.
+ Say Y if you own such a device and want to use it.
config DVB_USB_CXUSB
tristate "Conexant USB2.0 hybrid reference design support"
@@ -159,19 +104,84 @@ config DVB_USB_CXUSB_ANALOG
USB2.0 hybrid reference design.
Currently this mode is supported only on a Medion MD95700 device.
-config DVB_USB_M920X
- tristate "Uli m920x DVB-T USB2.0 support"
- depends on DVB_USB
- select DVB_MT352 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TDA1004X if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_QT1010 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_TDA827X if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_SIMPLE if MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the MSI Mega Sky 580 USB2.0 DVB-T receiver.
- Currently, only devices with a product id of
- "DTV USB MINI" (in cold state) are supported.
- Firmware required.
+config DVB_USB_DIB0700
+ tristate "DiBcom DiB0700 USB DVB devices (see help for supported devices)"
+ depends on DVB_USB
+ select DVB_DIB7000P if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_DIB7000M if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_DIB8000 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_USB_DIB3000MC if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_S5H1411 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_LGDT3305 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_MN88472 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TUNER_DIB0070 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TUNER_DIB0090 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_MT2266 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_XC2028 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_XC5000 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_XC4000 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_MXL5007T if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_TDA18250 if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Support for USB2.0/1.1 DVB receivers based on the DiB0700 USB bridge. The
+ USB bridge is also present in devices having the DiB7700 DVB-T-USB
+ silicon. This chip can be found in devices offered by Hauppauge,
+ Avermedia and other big and small companies.
+
+ For an up-to-date list of devices supported by this driver, have a look
+ on the LinuxTV Wiki at www.linuxtv.org.
+
+ Say Y if you own such a device and want to use it. You should build it as
+ a module.
+
+config DVB_USB_DIB3000MC
+ tristate
+ depends on DVB_USB
+ select DVB_DIB3000MC
+ help
+ This is a module with helper functions for accessing the
+ DIB3000MC from USB DVB devices. It must be a separate module
+ in case DVB_USB is built-in and DVB_DIB3000MC is a module,
+ and gets selected automatically when needed.
+
+config DVB_USB_DIBUSB_MB
+ tristate "DiBcom USB DVB-T devices (based on the DiB3000M-B) (see help for device list)"
+ depends on DVB_USB
+ select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_DIB3000MB
+ depends on DVB_DIB3000MC || !DVB_DIB3000MC
+ select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Support for USB 1.1 and 2.0 DVB-T receivers based on reference designs made by
+ DiBcom (<http://www.dibcom.fr>) equipped with a DiB3000M-B demodulator.
+
+ For an up-to-date list of devices supported by this driver, have a look
+ on the Linux-DVB Wiki at www.linuxtv.org.
+
+ Say Y if you own such a device and want to use it. You should build it as
+ a module.
+
+config DVB_USB_DIBUSB_MB_FAULTY
+ bool "Support faulty USB IDs"
+ depends on DVB_USB_DIBUSB_MB
+ help
+ Support for faulty USB IDs due to an invalid EEPROM on some Artec devices.
+
+config DVB_USB_DIBUSB_MC
+ tristate "DiBcom USB DVB-T devices (based on the DiB3000M-C/P) (see help for device list)"
+ depends on DVB_USB
+ select DVB_USB_DIB3000MC
+ select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Support for USB2.0 DVB-T receivers based on reference designs made by
+ DiBcom (<http://www.dibcom.fr>) equipped with a DiB3000M-C/P demodulator.
+
+ For an up-to-date list of devices supported by this driver, have a look
+ on the Linux-DVB Wiki at www.linuxtv.org.
+
+ Say Y if you own such a device and want to use it. You should build it as
+ a module.
config DVB_USB_DIGITV
tristate "Nebula Electronics uDigiTV DVB-T USB2.0 support"
@@ -182,65 +192,6 @@ config DVB_USB_DIGITV
help
Say Y here to support the Nebula Electronics uDigitV USB2.0 DVB-T receiver.
-config DVB_USB_VP7045
- tristate "TwinhanDTV Alpha/MagicBoxII, DNTV tinyUSB2, Beetle USB2.0 support"
- depends on DVB_USB
- help
- Say Y here to support the
-
- TwinhanDTV Alpha (stick) (VP-7045),
- TwinhanDTV MagicBox II (VP-7046),
- DigitalNow TinyUSB 2 DVB-t,
- DigitalRise USB 2.0 Ter (Beetle) and
- TYPHOON DVB-T USB DRIVE
-
- DVB-T USB2.0 receivers.
-
-config DVB_USB_VP702X
- tristate "TwinhanDTV StarBox and clones DVB-S USB2.0 support"
- depends on DVB_USB
- help
- Say Y here to support the
-
- TwinhanDTV StarBox,
- DigitalRise USB Starbox and
- TYPHOON DVB-S USB 2.0 BOX
-
- DVB-S USB2.0 receivers.
-
-config DVB_USB_GP8PSK
- tristate "GENPIX 8PSK->USB module support"
- depends on DVB_USB
- help
- Say Y here to support the
- GENPIX 8psk module
-
- DVB-S USB2.0 receivers.
-
-config DVB_USB_NOVA_T_USB2
- tristate "Hauppauge WinTV-NOVA-T usb2 DVB-T USB2.0 support"
- depends on DVB_USB
- select DVB_USB_DIB3000MC
- select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the Hauppauge WinTV-NOVA-T usb2 DVB-T USB2.0 receiver.
-
-config DVB_USB_TTUSB2
- tristate "Pinnacle 400e DVB-S USB2.0 support"
- depends on DVB_USB
- select DVB_TDA10086 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_LNBP21 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TDA826X if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TDA10023 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_TDA10048 if MEDIA_SUBDRV_AUTOSELECT
- select MEDIA_TUNER_TDA827X if MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the Pinnacle 400e DVB-S USB2.0 receiver and
- the TechnoTrend CT-3650 CI DVB-C/T USB2.0 receiver. The
- firmware protocol used by this module is similar to the one used by the
- old ttusb-driver - that's why the module is called dvb-usb-ttusb2.
-
config DVB_USB_DTT200U
tristate "WideView WT-200U and WT-220U (pen) DVB-T USB2.0 support (Yakumo/Hama/Typhoon/Yuan)"
depends on DVB_USB
@@ -251,43 +202,13 @@ config DVB_USB_DTT200U
The WT-220U and its clones are pen-sized.
-config DVB_USB_OPERA1
- tristate "Opera1 DVB-S USB2.0 receiver"
+config DVB_USB_DTV5100
+ tristate "AME DTV-5100 USB2.0 DVB-T support"
depends on DVB_USB
- select DVB_STV0299 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
- help
- Say Y here to support the Opera DVB-S USB2.0 receiver.
-
-config DVB_USB_AF9005
- tristate "Afatech AF9005 DVB-T USB1.1 support"
- depends on DVB_USB
- select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_ZL10353 if MEDIA_SUBDRV_AUTOSELECT
select MEDIA_TUNER_QT1010 if MEDIA_SUBDRV_AUTOSELECT
help
- Say Y here to support the Afatech AF9005 based DVB-T USB1.1 receiver
- and the TerraTec Cinergy T USB XE (Rev.1)
-
-config DVB_USB_AF9005_REMOTE
- tristate "Afatech AF9005 default remote control support"
- depends on DVB_USB_AF9005
- help
- Say Y here to support the default remote control decoding for the
- Afatech AF9005 based receiver.
-
-config DVB_USB_PCTV452E
- tristate "Pinnacle PCTV HDTV Pro USB device/TT Connect S2-3600"
- depends on DVB_USB
- select TTPCI_EEPROM
- select DVB_ISL6423 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_LNBP22 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_STB0899 if MEDIA_SUBDRV_AUTOSELECT
- select DVB_STB6100 if MEDIA_SUBDRV_AUTOSELECT
- help
- Support for external USB adapter designed by Pinnacle,
- shipped under the brand name 'PCTV HDTV Pro USB'.
- Also supports TT Connect S2-3600/3650 cards.
- Say Y if you own such a device and want to use it.
+ Say Y here to support the AME DTV-5100 USB2.0 DVB-T receiver.
config DVB_USB_DW2102
tristate "DvbWorld & TeVii DVB-S/S2 USB2.0 support"
@@ -312,29 +233,59 @@ config DVB_USB_DW2102
Say Y here to support the DvbWorld, TeVii, Prof, TechnoTrend
DVB-S/S2 USB2.0 receivers.
-config DVB_USB_CINERGY_T2
- tristate "Terratec CinergyT2/qanu USB 2.0 DVB-T receiver"
+config DVB_USB_GP8PSK
+ tristate "GENPIX 8PSK->USB module support"
depends on DVB_USB
help
- Support for "TerraTec CinergyT2" USB2.0 Highspeed DVB Receivers
+ Say Y here to support the
+ GENPIX 8psk module
- Say Y if you own such a device and want to use it.
+ DVB-S USB2.0 receivers.
-config DVB_USB_DTV5100
- tristate "AME DTV-5100 USB2.0 DVB-T support"
+config DVB_USB_M920X
+ tristate "Uli m920x DVB-T USB2.0 support"
depends on DVB_USB
- select DVB_ZL10353 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_MT352 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TDA1004X if MEDIA_SUBDRV_AUTOSELECT
select MEDIA_TUNER_QT1010 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_TDA827X if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_SIMPLE if MEDIA_SUBDRV_AUTOSELECT
help
- Say Y here to support the AME DTV-5100 USB2.0 DVB-T receiver.
+ Say Y here to support the MSI Mega Sky 580 USB2.0 DVB-T receiver.
+ Currently, only devices with a product id of
+ "DTV USB MINI" (in cold state) are supported.
+ Firmware required.
-config DVB_USB_AZ6027
- tristate "Azurewave DVB-S/S2 USB2.0 AZ6027 support"
+config DVB_USB_NOVA_T_USB2
+ tristate "Hauppauge WinTV-NOVA-T usb2 DVB-T USB2.0 support"
depends on DVB_USB
+ select DVB_USB_DIB3000MC
+ select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to support the Hauppauge WinTV-NOVA-T usb2 DVB-T USB2.0 receiver.
+
+config DVB_USB_OPERA1
+ tristate "Opera1 DVB-S USB2.0 receiver"
+ depends on DVB_USB
+ select DVB_STV0299 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to support the Opera DVB-S USB2.0 receiver.
+
+config DVB_USB_PCTV452E
+ tristate "Pinnacle PCTV HDTV Pro USB device/TT Connect S2-3600"
+ depends on DVB_USB
+ select TTPCI_EEPROM
+ select DVB_ISL6423 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_LNBP22 if MEDIA_SUBDRV_AUTOSELECT
select DVB_STB0899 if MEDIA_SUBDRV_AUTOSELECT
select DVB_STB6100 if MEDIA_SUBDRV_AUTOSELECT
help
- Say Y here to support the AZ6027 device
+ Support for external USB adapter designed by Pinnacle,
+ shipped under the brand name 'PCTV HDTV Pro USB'.
+ Also supports TT Connect S2-3600/3650 cards.
+ Say Y if you own such a device and want to use it.
config DVB_USB_TECHNISAT_USB2
tristate "Technisat DVB-S/S2 USB2.0 support"
@@ -343,3 +294,56 @@ config DVB_USB_TECHNISAT_USB2
select DVB_STV6110x if MEDIA_SUBDRV_AUTOSELECT
help
Say Y here to support the Technisat USB2 DVB-S/S2 device
+
+config DVB_USB_TTUSB2
+ tristate "Pinnacle 400e DVB-S USB2.0 support"
+ depends on DVB_USB
+ select DVB_TDA10086 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_LNBP21 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TDA826X if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TDA10023 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_TDA10048 if MEDIA_SUBDRV_AUTOSELECT
+ select MEDIA_TUNER_TDA827X if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to support the Pinnacle 400e DVB-S USB2.0 receiver and
+ the TechnoTrend CT-3650 CI DVB-C/T USB2.0 receiver. The
+ firmware protocol used by this module is similar to the one used by the
+ old ttusb-driver - that's why the module is called dvb-usb-ttusb2.
+
+config DVB_USB_UMT_010
+ tristate "HanfTek UMT-010 DVB-T USB2.0 support"
+ depends on DVB_USB
+ select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_USB_DIB3000MC
+ select MEDIA_TUNER_MT2060 if MEDIA_SUBDRV_AUTOSELECT
+ select DVB_MT352 if MEDIA_SUBDRV_AUTOSELECT
+ help
+ Say Y here to support the HanfTek UMT-010 USB2.0 stick-sized DVB-T receiver.
+
+config DVB_USB_VP702X
+ tristate "TwinhanDTV StarBox and clones DVB-S USB2.0 support"
+ depends on DVB_USB
+ help
+ Say Y here to support the
+
+ TwinhanDTV StarBox,
+ DigitalRise USB Starbox and
+ TYPHOON DVB-S USB 2.0 BOX
+
+ DVB-S USB2.0 receivers.
+
+config DVB_USB_VP7045
+ tristate "TwinhanDTV Alpha/MagicBoxII, DNTV tinyUSB2, Beetle USB2.0 support"
+ depends on DVB_USB
+ help
+ Say Y here to support the
+
+ TwinhanDTV Alpha (stick) (VP-7045),
+ TwinhanDTV MagicBox II (VP-7046),
+ DigitalNow TinyUSB 2 DVB-t,
+ DigitalRise USB 2.0 Ter (Beetle) and
+ TYPHOON DVB-T USB DRIVE
+
+ DVB-T USB2.0 receivers.
+
+endif
diff --git a/drivers/media/usb/gspca/Kconfig b/drivers/media/usb/gspca/Kconfig
index 2b106a7fcf4c..9c1939ce6be4 100644
--- a/drivers/media/usb/gspca/Kconfig
+++ b/drivers/media/usb/gspca/Kconfig
@@ -16,13 +16,8 @@ menuconfig USB_GSPCA
To compile this driver as modules, choose M here: the
module will be called gspca_main.
-
if USB_GSPCA && VIDEO_DEV
-source "drivers/media/usb/gspca/m5602/Kconfig"
-source "drivers/media/usb/gspca/stv06xx/Kconfig"
-source "drivers/media/usb/gspca/gl860/Kconfig"
-
config USB_GSPCA_BENQ
tristate "Benq USB Camera Driver"
depends on VIDEO_DEV && USB_GSPCA
@@ -251,6 +246,15 @@ config USB_GSPCA_SONIXJ
To compile this driver as a module, choose M here: the
module will be called gspca_sonixj
+config USB_GSPCA_SPCA1528
+ tristate "SPCA1528 USB Camera Driver"
+ depends on VIDEO_DEV && USB_GSPCA
+ help
+ Say Y here if you want support for cameras based on the SPCA1528 chip.
+
+ To compile this driver as a module, choose M here: the
+ module will be called gspca_spca1528.
+
config USB_GSPCA_SPCA500
tristate "SPCA500 USB Camera Driver"
depends on VIDEO_DEV && USB_GSPCA
@@ -305,15 +309,6 @@ config USB_GSPCA_SPCA561
To compile this driver as a module, choose M here: the
module will be called gspca_spca561.
-config USB_GSPCA_SPCA1528
- tristate "SPCA1528 USB Camera Driver"
- depends on VIDEO_DEV && USB_GSPCA
- help
- Say Y here if you want support for cameras based on the SPCA1528 chip.
-
- To compile this driver as a module, choose M here: the
- module will be called gspca_spca1528.
-
config USB_GSPCA_SQ905
tristate "SQ Technologies SQ905 based USB Camera Driver"
depends on VIDEO_DEV && USB_GSPCA
@@ -453,4 +448,8 @@ config USB_GSPCA_ZC3XX
To compile this driver as a module, choose M here: the
module will be called gspca_zc3xx.
+source "drivers/media/usb/gspca/gl860/Kconfig"
+source "drivers/media/usb/gspca/m5602/Kconfig"
+source "drivers/media/usb/gspca/stv06xx/Kconfig"
+
endif
--
2.35.1
next prev parent reply other threads:[~2022-03-14 16:38 UTC|newest]
Thread overview: 162+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-03-14 16:33 [PATCH v2 00/67] media: Kconfig/Makefile reorg Mauro Carvalho Chehab
2022-03-14 16:33 ` Mauro Carvalho Chehab
2022-03-14 16:33 ` Mauro Carvalho Chehab
2022-03-14 16:33 ` Mauro Carvalho Chehab
2022-03-14 16:33 ` Mauro Carvalho Chehab
2022-03-14 16:33 ` Mauro Carvalho Chehab
2022-03-14 16:33 ` [PATCH v2 01/67] media: xc2028: rename the driver from tuner-xc2028 Mauro Carvalho Chehab
2022-03-14 16:33 ` [PATCH v2 02/67] media: Makefiles: remove extra spaces Mauro Carvalho Chehab
2022-03-14 16:33 ` [PATCH v2 03/67] media: Makefiles: sort entries where it fits Mauro Carvalho Chehab
2022-03-14 16:33 ` [PATCH v2 04/67] media: platform: Makefile: reorganize its contents Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 05/67] media: platform: move platform menu dependencies to drivers Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 06/67] media: platform: place Aspeed driver on a separate dir Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 07/67] media: platform: place NXP drivers " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 08/67] media: platform: place Intel " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 09/67] media: platform: place Via " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 10/67] media: platform: place Renesas " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 11/67] media: platform: allegro-dvt: move config to its own file Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 12/67] media: platform: amphion: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 13/67] media: platform: coda: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 14/67] media: platform: exynos-gsc: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 15/67] media: platform: ge2d: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 16/67] media: platform: mtk-jpeg: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 17/67] media: platform: mtk-mdp: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 18/67] media: platform: mtk-vcodec: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 19/67] media: platform: mtk-vpu: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 20/67] media: platform: omap3isp: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 21/67] media: platform: camss: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 22/67] media: platform: venus: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 23/67] media: platform: rga: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 24/67] media: platform: s3c-camif: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 25/67] media: platform: s5p-g2d: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 26/67] media: platform: hva: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 27/67] media: platform: stm32: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 28/67] media: platform: sun8i-di: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 29/67] media: platform: sun8i-rotate: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 30/67] media: platform: vde: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 31/67] media: platform: ti-vpe: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 32/67] media: platform: rkisp1: " Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 33/67] media: platform: delta: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 34/67] media: platform: bdisp: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 35/67] media: platform: s5p-mfc: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 36/67] media: platform: s5p-jpeg: " Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 37/67] media: platform: Kconfig: sort entries Mauro Carvalho Chehab
2022-03-15 16:56 ` Jernej Škrabec
2022-03-14 16:34 ` [PATCH v2 38/67] media: platform: move some manufacturer entries Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 39/67] media: platform: Kconfig: place platform drivers on a submenu Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 40/67] media: platform: rename coda/ to chips-media/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 41/67] media: platform: rename marvell-ccic/ to marvell/ Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 42/67] media: platform: rename meson/ge2d/ to amlogic/meson-ge2d/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 43/67] media: platform: rename mtk-jpeg/ to mediatek/mtk-jpeg/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 44/67] media: platform: rename mtk-mdp/ to mediatek/mtk-mdp/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 45/67] media: platform: rename mtk-vcodec/ to mediatek/mtk-vcodec/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 46/67] media: platform: rename mtk-vpu/ to mediatek/mtk-vpu/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 47/67] media: platform: rename sunxi/ to allwinner/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 17:22 ` Jernej Škrabec
2022-03-14 17:22 ` Jernej Škrabec
2022-03-15 5:40 ` Mauro Carvalho Chehab
2022-03-15 5:40 ` Mauro Carvalho Chehab
2022-03-15 6:54 ` Laurent Pinchart
2022-03-15 6:54 ` Laurent Pinchart
2022-03-15 8:27 ` Mauro Carvalho Chehab
2022-03-15 8:27 ` Mauro Carvalho Chehab
2022-03-15 8:35 ` Laurent Pinchart
2022-03-15 8:35 ` Laurent Pinchart
2022-03-15 18:04 ` Jernej Škrabec
2022-03-15 18:04 ` Jernej Škrabec
2022-03-16 13:13 ` Mauro Carvalho Chehab
2022-03-16 13:13 ` Mauro Carvalho Chehab
2022-03-16 13:10 ` Mauro Carvalho Chehab
2022-03-16 13:10 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 48/67] media: platform: rename tegra/vde/ to nvidia/tegra-vde/ Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 49/67] media: platform: rename exynos4-is/ to samsung/exynos4-is/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 50/67] media: platform: rename exynos-gsc/ to samsung/exynos-gsc/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 51/67] media: platform: rename s3c-camif/ to samsung/s3c-camif/ Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 52/67] media: platform: rename s5p-g2d/ to samsung/s5p-g2d/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
[not found] ` <CGME20220317191357eucas1p1abc9a313ef2f320bda365388e72e0327@eucas1p1.samsung.com>
2022-03-17 19:13 ` Lukasz Stelmach
2022-03-17 19:13 ` Lukasz Stelmach
2022-03-14 16:34 ` [PATCH v2 53/67] media: platform: rename s5p-jpeg/ to samsung/s5p-jpeg/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 54/67] media: platform: rename s5p-mfc/ to samsung/s5p-mfc/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 55/67] media: platform: rename stm32/ to stm/stm32/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 56/67] media: platform: rename sti/ to stm/sti/ Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 57/67] media: platform: rename am437x/ to ti/am437x/ Mauro Carvalho Chehab
2022-03-17 19:16 ` Lad, Prabhakar
2022-03-14 16:34 ` [PATCH v2 58/67] media: platform: rename davinci/ to ti/davinci/ Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 59/67] media: platform: rename omap3isp/ to ti/omap3isp/ Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 60/67] media: platform: rename omap/ to ti/omap/ Mauro Carvalho Chehab
2022-03-14 18:31 ` Péter Ujfalusi
2022-03-14 16:34 ` [PATCH v2 61/67] media: platform: re-structure TI drivers Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 62/67] media: platform: ti/Kconfig: move VPE/CAL entries to it Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 63/67] media: platform: Create vendor/{Makefile,Kconfig} files Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 63/67] media: platform: Create vendor/{Makefile, Kconfig} files Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` [PATCH v2 64/67] media: platform/*/Kconfig: make manufacturer menus more uniform Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:34 ` Mauro Carvalho Chehab
2022-03-14 16:35 ` [PATCH v2 65/67] media: Kconfig: cleanup VIDEO_DEV dependencies Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
[not found] ` <CGME20220317192136eucas1p185dfbf79e792ebdc4c5614a90c1b0cd8@eucas1p1.samsung.com>
2022-03-17 19:21 ` Lukasz Stelmach
2022-03-17 19:21 ` Lukasz Stelmach
2022-03-17 19:21 ` Lukasz Stelmach
2022-03-17 19:21 ` Lukasz Stelmach
2022-03-17 19:21 ` Lukasz Stelmach
2022-03-17 19:21 ` Lukasz Stelmach
2022-03-14 16:35 ` Mauro Carvalho Chehab [this message]
2022-03-14 16:35 ` [PATCH v2 67/67] media: platform: rename mediatek/mtk-jpeg/ to mediatek/jpeg/ Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
2022-03-14 16:35 ` Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=79bfd880f0f7debc6bda04f6f93ec0bd56e58bc7.1647274407.git.mchehab@kernel.org \
--to=mchehab@kernel.org \
--cc=c.hemp@phytec.de \
--cc=dwlsalmeida@gmail.com \
--cc=ezequiel@vanguardiasur.com.ar \
--cc=hverkuil@xs4all.nl \
--cc=jacopo@jmondi.org \
--cc=jimmy.su@intel.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=martinax.krasteva@intel.com \
--cc=sakari.ailus@linux.intel.com \
--cc=sean@mess.org \
--cc=shawnx.tu@intel.com \
--cc=uwe@kleine-koenig.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.