From: Steve Twiss <stwiss.opensource@diasemi.com> To: Ian Campbell <ijc+devicetree@hellion.org.uk>, Kumar Gala <galak@codeaurora.org>, Mark Rutland <mark.rutland@arm.com>, Pawel Moll <pawel.moll@arm.com>, Rob Herring <robh+dt@kernel.org> Cc: DT <devicetree@vger.kernel.org>, David Dajun Chen <david.chen@diasemi.com>, Grant Likely <grant.likely@linaro.org>, LKML <linux-kernel@vger.kernel.org>, Lee Jones <lee.jones@linaro.org>, Mark Brown <broonie@linaro.org>, Philipp Zabel <p.zabel@pengutronix.de>, Rob Herring <robh+dt@kernel.org>, Samuel Ortiz <sameo@linux.intel.com>, "Support Opensource" <support.opensource@diasemi.com> Subject: [PATCH V2 2/2] devicetree: Add bindings for DA9063 Date: Mon, 19 Jan 2015 16:29:51 +0000 [thread overview] Message-ID: <7cd71ad47ba0cccd2d2da45fc3f1f82df0842a8c.1421684991.git.stwiss.opensource@diasemi.com> (raw) In-Reply-To: <cover.1421684991.git.stwiss.opensource@diasemi.com> From: Steve Twiss <stwiss.opensource@diasemi.com> Add device tree bindings for DA9063 regulators; Real-Time Clock and Watchdog. This patch is dependent on PATCH V2 1/2 Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> --- This patch applies against linux-next and v3.19-rc4 Documentation/devicetree/bindings/mfd/da9063.txt | 94 ++++++++++++++++++++++++ 1 file changed, 94 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/da9063.txt diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt new file mode 100644 index 0000000..ac26af4 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9063.txt @@ -0,0 +1,94 @@ +* Dialog DA9063 Power Management Integrated Circuit (PMIC) + +DA9093 consists of a large and varied group of sub-devices (I2C Only): + +Device Supply Names Description +------ ------------ ----------- +da9063-regulator : : LDOs & BUCKs +da9063-rtc : : Real-Time Clock +da9063-watchdog : : Watchdog + +====== + +Required properties: + +- compatible : Should be "dlg,da9063-ca", "dlg,da9063-bb" or/and + "dlg,da9063-ad". +- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be + modified to match the chip's OTP settings). +- interrupt-parent : Specifies the reference to the interrupt controller for + the DA9063. +- interrupts : IRQ line information. +- interrupt-controller + +Sub-nodes: + +- regulators : This node defines the settings for the LDOs and BUCKs. The + DA9063 regulators are bound using their names listed below: + + bcore1 : BUCK CORE1 + bcore2 : BUCK CORE2 + bpro : BUCK PRO + bmem : BUCK MEM + bio : BUCK IO + bperi : BUCK PERI + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + ldo5 : LDO_5 + ldo6 : LDO_6 + ldo7 : LDO_7 + ldo8 : LDO_8 + ldo9 : LDO_9 + ldo10 : LDO_10 + ldo11 : LDO_11 + + The component follows the standard regulator framework and the bindings + details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +- rtc : This node defines settings for the Real-Time Clock associated with + the DA9063. There are currently no entries in this binding, however + compatible = "dlg,da9063-rtc" should be added if a node is created. + +- watchdog : This node defines settings for the Watchdog timer associated + with the DA9063. There are currently no entries in this binding, however + compatible = "dlg,da9063-watchdog" should be added if a node is created. + + +Example: + + pmic0: da9063@58 { + compatible = "dlg,da9063-ca", "dlg,da9063-bb", "dlg,da9063-ad"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9063-rtc"; + }; + + wdt { + compatible = "dlg,da9063-watchdog"; + }; + + regulators { + DA9063_BCORE1: bcore1 { + regulator-name = "BCORE1"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <500000>; + regulator-max-microamp = <2000000>; + regulator-boot-on; + }; + DA9063_LDO11: ldo11 { + regulator-name = "LDO_11"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3600000>; + regulator-boot-on; + }; + }; + }; + -- end-of-patch for PATCH V2
WARNING: multiple messages have this Message-ID (diff)
From: Steve Twiss <stwiss.opensource@diasemi.com> To: Ian Campbell <ijc+devicetree@hellion.org.uk>, Kumar Gala <galak@codeaurora.org>, Mark Rutland <mark.rutland@arm.com>, Pawel Moll <pawel.moll@arm.com> Cc: DT <devicetree@vger.kernel.org>, David Dajun Chen <david.chen@diasemi.com>, Grant Likely <grant.likely@linaro.org>, LKML <linux-kernel@vger.kernel.org>, Lee Jones <lee.jones@linaro.org>, Mark Brown <broonie@linaro.org>, Philipp Zabel <p.zabel@pengutronix.de>, Rob Herring <robh+dt@kernel.org>, Samuel Ortiz <sameo@linux.intel.com>, Support Opensource <support.opensource@diasemi.com> Subject: [PATCH V2 2/2] devicetree: Add bindings for DA9063 Date: Mon, 19 Jan 2015 16:29:51 +0000 [thread overview] Message-ID: <7cd71ad47ba0cccd2d2da45fc3f1f82df0842a8c.1421684991.git.stwiss.opensource@diasemi.com> (raw) In-Reply-To: <cover.1421684991.git.stwiss.opensource@diasemi.com> From: Steve Twiss <stwiss.opensource@diasemi.com> Add device tree bindings for DA9063 regulators; Real-Time Clock and Watchdog. This patch is dependent on PATCH V2 1/2 Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> --- This patch applies against linux-next and v3.19-rc4 Documentation/devicetree/bindings/mfd/da9063.txt | 94 ++++++++++++++++++++++++ 1 file changed, 94 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/da9063.txt diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt new file mode 100644 index 0000000..ac26af4 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9063.txt @@ -0,0 +1,94 @@ +* Dialog DA9063 Power Management Integrated Circuit (PMIC) + +DA9093 consists of a large and varied group of sub-devices (I2C Only): + +Device Supply Names Description +------ ------------ ----------- +da9063-regulator : : LDOs & BUCKs +da9063-rtc : : Real-Time Clock +da9063-watchdog : : Watchdog + +====== + +Required properties: + +- compatible : Should be "dlg,da9063-ca", "dlg,da9063-bb" or/and + "dlg,da9063-ad". +- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be + modified to match the chip's OTP settings). +- interrupt-parent : Specifies the reference to the interrupt controller for + the DA9063. +- interrupts : IRQ line information. +- interrupt-controller + +Sub-nodes: + +- regulators : This node defines the settings for the LDOs and BUCKs. The + DA9063 regulators are bound using their names listed below: + + bcore1 : BUCK CORE1 + bcore2 : BUCK CORE2 + bpro : BUCK PRO + bmem : BUCK MEM + bio : BUCK IO + bperi : BUCK PERI + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + ldo5 : LDO_5 + ldo6 : LDO_6 + ldo7 : LDO_7 + ldo8 : LDO_8 + ldo9 : LDO_9 + ldo10 : LDO_10 + ldo11 : LDO_11 + + The component follows the standard regulator framework and the bindings + details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +- rtc : This node defines settings for the Real-Time Clock associated with + the DA9063. There are currently no entries in this binding, however + compatible = "dlg,da9063-rtc" should be added if a node is created. + +- watchdog : This node defines settings for the Watchdog timer associated + with the DA9063. There are currently no entries in this binding, however + compatible = "dlg,da9063-watchdog" should be added if a node is created. + + +Example: + + pmic0: da9063@58 { + compatible = "dlg,da9063-ca", "dlg,da9063-bb", "dlg,da9063-ad"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9063-rtc"; + }; + + wdt { + compatible = "dlg,da9063-watchdog"; + }; + + regulators { + DA9063_BCORE1: bcore1 { + regulator-name = "BCORE1"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <500000>; + regulator-max-microamp = <2000000>; + regulator-boot-on; + }; + DA9063_LDO11: ldo11 { + regulator-name = "LDO_11"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3600000>; + regulator-boot-on; + }; + }; + }; + -- end-of-patch for PATCH V2
next prev parent reply other threads:[~2015-01-19 16:37 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-01-19 16:29 [PATCH V2 0/2] Add device tree support for DA9063 Opensource [Steve Twiss] 2015-01-19 16:29 ` [PATCH V2 1/2] mfd: da9063: Add device tree support Steve Twiss 2015-01-19 16:29 ` Steve Twiss 2015-01-20 10:45 ` Lee Jones 2015-01-20 10:45 ` Lee Jones 2015-01-20 13:23 ` Opensource [Steve Twiss] 2015-01-20 13:23 ` Opensource [Steve Twiss] 2015-01-19 16:29 ` Steve Twiss [this message] 2015-01-19 16:29 ` [PATCH V2 2/2] devicetree: Add bindings for DA9063 Steve Twiss 2015-01-20 10:42 ` Lee Jones 2015-01-20 10:42 ` Lee Jones 2015-01-20 10:41 ` [PATCH V2 0/2] Add device tree support " Lee Jones
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=7cd71ad47ba0cccd2d2da45fc3f1f82df0842a8c.1421684991.git.stwiss.opensource@diasemi.com \ --to=stwiss.opensource@diasemi.com \ --cc=broonie@linaro.org \ --cc=david.chen@diasemi.com \ --cc=devicetree@vger.kernel.org \ --cc=galak@codeaurora.org \ --cc=grant.likely@linaro.org \ --cc=ijc+devicetree@hellion.org.uk \ --cc=lee.jones@linaro.org \ --cc=linux-kernel@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=p.zabel@pengutronix.de \ --cc=pawel.moll@arm.com \ --cc=robh+dt@kernel.org \ --cc=sameo@linux.intel.com \ --cc=support.opensource@diasemi.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.