* [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64
@ 2018-09-26 4:53 ` Chen-Yu Tsai
0 siblings, 0 replies; 6+ messages in thread
From: Chen-Yu Tsai @ 2018-09-26 4:53 UTC (permalink / raw)
To: Heiko Stuebner
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-rockchip,
linux-mtd, linux-spi, linux-kernel, Mark Brown
The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
that supports the JEDEC read-ID command.
This patch enables the SPI controller and adds a device node
for the flash chip using the generic "jedec,spi-nor" comaptible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
This was working on linux-next 20180910, but now fails on linux-next
20180925, with the following error messages:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -2
Reverting the spi/for-next branch makes it work again:
m25p80 spi0.0: gd25q128 (16384 Kbytes)
Not sure what's up.
---
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 9ee4f57557f3..2170cf63845e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -290,6 +290,18 @@
};
};
+&spi0 {
+ status = "okay";
+
+ spiflash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ /* maximum speed for Rockchip SPI */
+ spi-max-frequency = <50000000>;
+ };
+};
+
&tsadc {
rockchip,hw-tshut-mode = <0>;
rockchip,hw-tshut-polarity = <0>;
--
2.19.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64
@ 2018-09-26 4:53 ` Chen-Yu Tsai
0 siblings, 0 replies; 6+ messages in thread
From: Chen-Yu Tsai @ 2018-09-26 4:53 UTC (permalink / raw)
To: linux-arm-kernel
The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
that supports the JEDEC read-ID command.
This patch enables the SPI controller and adds a device node
for the flash chip using the generic "jedec,spi-nor" comaptible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
This was working on linux-next 20180910, but now fails on linux-next
20180925, with the following error messages:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -2
Reverting the spi/for-next branch makes it work again:
m25p80 spi0.0: gd25q128 (16384 Kbytes)
Not sure what's up.
---
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 9ee4f57557f3..2170cf63845e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -290,6 +290,18 @@
};
};
+&spi0 {
+ status = "okay";
+
+ spiflash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ /* maximum speed for Rockchip SPI */
+ spi-max-frequency = <50000000>;
+ };
+};
+
&tsadc {
rockchip,hw-tshut-mode = <0>;
rockchip,hw-tshut-polarity = <0>;
--
2.19.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64
2018-09-26 4:53 ` Chen-Yu Tsai
@ 2018-09-26 7:10 ` Frieder Schrempf
-1 siblings, 0 replies; 6+ messages in thread
From: Frieder Schrempf @ 2018-09-26 7:10 UTC (permalink / raw)
To: Chen-Yu Tsai, Heiko Stuebner
Cc: devicetree, linux-kernel, linux-spi, linux-rockchip, Mark Brown,
linux-mtd, linux-arm-kernel
On 26.09.2018 06:53, Chen-Yu Tsai wrote:
> The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
> or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
> that supports the JEDEC read-ID command.
>
> This patch enables the SPI controller and adds a device node
> for the flash chip using the generic "jedec,spi-nor" comaptible.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
>
> This was working on linux-next 20180910, but now fails on linux-next
> 20180925, with the following error messages:
>
> m25p80 spi0.0: error -22 reading 9f
> m25p80: probe of spi0.0 failed with error -2
>
> Reverting the spi/for-next branch makes it work again:
>
> m25p80 spi0.0: gd25q128 (16384 Kbytes)
>
> Not sure what's up.
The reason is probably an issue that was introduced here: [1], and it
was fixed here: [2].
[1]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/drivers/spi?id=380583227c0c7f52383b0cd5c0e2de93ed31d553
[2]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/drivers/spi?id=4c53f98555fdbf1cc291cab8ffa5e1507a4f25d9
>
> ---
> arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> index 9ee4f57557f3..2170cf63845e 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> @@ -290,6 +290,18 @@
> };
> };
>
> +&spi0 {
> + status = "okay";
> +
> + spiflash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> +
> + /* maximum speed for Rockchip SPI */
> + spi-max-frequency = <50000000>;
> + };
> +};
> +
> &tsadc {
> rockchip,hw-tshut-mode = <0>;
> rockchip,hw-tshut-polarity = <0>;
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64
@ 2018-09-26 7:10 ` Frieder Schrempf
0 siblings, 0 replies; 6+ messages in thread
From: Frieder Schrempf @ 2018-09-26 7:10 UTC (permalink / raw)
To: linux-arm-kernel
On 26.09.2018 06:53, Chen-Yu Tsai wrote:
> The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
> or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
> that supports the JEDEC read-ID command.
>
> This patch enables the SPI controller and adds a device node
> for the flash chip using the generic "jedec,spi-nor" comaptible.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
>
> This was working on linux-next 20180910, but now fails on linux-next
> 20180925, with the following error messages:
>
> m25p80 spi0.0: error -22 reading 9f
> m25p80: probe of spi0.0 failed with error -2
>
> Reverting the spi/for-next branch makes it work again:
>
> m25p80 spi0.0: gd25q128 (16384 Kbytes)
>
> Not sure what's up.
The reason is probably an issue that was introduced here: [1], and it
was fixed here: [2].
[1]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/drivers/spi?id=380583227c0c7f52383b0cd5c0e2de93ed31d553
[2]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/drivers/spi?id=4c53f98555fdbf1cc291cab8ffa5e1507a4f25d9
>
> ---
> arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> index 9ee4f57557f3..2170cf63845e 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> @@ -290,6 +290,18 @@
> };
> };
>
> +&spi0 {
> + status = "okay";
> +
> + spiflash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> +
> + /* maximum speed for Rockchip SPI */
> + spi-max-frequency = <50000000>;
> + };
> +};
> +
> &tsadc {
> rockchip,hw-tshut-mode = <0>;
> rockchip,hw-tshut-polarity = <0>;
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64
2018-09-26 4:53 ` Chen-Yu Tsai
@ 2018-09-26 11:38 ` Heiko Stuebner
-1 siblings, 0 replies; 6+ messages in thread
From: Heiko Stuebner @ 2018-09-26 11:38 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-mtd,
linux-spi, linux-kernel, Mark Brown
Am Mittwoch, 26. September 2018, 06:53:57 CEST schrieb Chen-Yu Tsai:
> The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
> or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
> that supports the JEDEC read-ID command.
>
> This patch enables the SPI controller and adds a device node
> for the flash chip using the generic "jedec,spi-nor" comaptible.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
applied for 4.20
Thanks
Heiko
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64
@ 2018-09-26 11:38 ` Heiko Stuebner
0 siblings, 0 replies; 6+ messages in thread
From: Heiko Stuebner @ 2018-09-26 11:38 UTC (permalink / raw)
To: linux-arm-kernel
Am Mittwoch, 26. September 2018, 06:53:57 CEST schrieb Chen-Yu Tsai:
> The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
> or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
> that supports the JEDEC read-ID command.
>
> This patch enables the SPI controller and adds a device node
> for the flash chip using the generic "jedec,spi-nor" comaptible.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
applied for 4.20
Thanks
Heiko
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2018-09-26 11:39 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-09-26 4:53 [PATCH] arm64: dts: rockchip: Enable SPI NOR flash on Rock64 Chen-Yu Tsai
2018-09-26 4:53 ` Chen-Yu Tsai
2018-09-26 7:10 ` Frieder Schrempf
2018-09-26 7:10 ` Frieder Schrempf
2018-09-26 11:38 ` Heiko Stuebner
2018-09-26 11:38 ` Heiko Stuebner
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.