* [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed
@ 2018-05-09 15:56 Ibai Erkiaga
2018-05-10 8:20 ` Michal Simek
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Ibai Erkiaga @ 2018-05-09 15:56 UTC (permalink / raw)
To: u-boot
Initial support for Avnet MiniZed board. Tested UART1 (serial console),
QSPI(Flash), SDHCI1 (eMMC), USB.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
---
Changes for v2:
-board model changed to use Avent prefix
-usb phy driver changed usb-no-xceiv
-removed gpio and intc binding
-fixed-partitions usage
---
U-Boot 2018.05-00023-gdf332c1-dirty (May 09 2018 - 14:50:51 +0100)
Model: Avnet Zynq MiniZed Development Board
Board: Xilinx Zynq
Silicon: v3.1
DRAM: ECC disabled 512 MiB
MMC: sdhci at e0101000: 0
Loading Environment from SPI Flash... SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial at e0001000
Out: serial at e0001000
Err: serial at e0001000
Net: No ethernet found.
Hit any key to stop autoboot: 0
Zynq> fatls mmc 0
16783864 image.ub
183 wpa_supplicant.conf
1391116 smallboot.bin
3 file(s), 0 dir(s)
Zynq> sf probe 0 0 0
SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Zynq> usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Zynq> fatls usb 0
12 test.txt
1 file(s), 0 dir(s)
Zynq>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/zynq-minized.dts | 104 ++++++++++++++++++++++++++++++++++++++++
configs/zynq_minized_defconfig | 68 ++++++++++++++++++++++++++
3 files changed, 173 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/dts/zynq-minized.dts
create mode 100644 configs/zynq_minized_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 6fe93a8..5c5f8a8 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-cc108.dtb \
zynq-cse-qspi-single.dtb \
zynq-microzed.dtb \
+ zynq-minized.dtb \
zynq-picozed.dtb \
zynq-syzygy-hub.dtb \
zynq-topic-miami.dtb \
diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
new file mode 100644
index 0000000..68fe09a
--- /dev/null
+++ b/arch/arm/dts/zynq-minized.dts
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Avnet MiniZed board
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
+ */
+
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ model = "Avnet Zynq MiniZed Development Board";
+ compatible = "avnet,minized", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart0;
+ spi0 = &qspi;
+ mmc0 = &sdhci0;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <0>;
+ num-cs = <1>;
+ flash at 0 {
+ compatible = "micron,m25p128";
+ reg = <0x0>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0xff0000>;
+ };
+
+ partition at 0270000 {
+ label = "kernel";
+ reg = <0x270000 0xd80000>;
+ };
+
+ partition at ff0000 {
+ label = "bootenv";
+ reg = <0xff0000 0x10000>;
+ };
+
+ partition at 1000000 {
+ label = "spare";
+ reg = <0x1000000 0x0>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */ };
+
+&sdhci1 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard at 0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ broken-hpi;
+ };
+};
diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
new file mode 100644
index 0000000..05cfc0e
--- /dev/null
+++ b/configs/zynq_minized_defconfig
@@ -0,0 +1,68 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ZYNQ=y
+CONFIG_SYS_TEXT_BASE=0x4000000
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R_ADDR=0x200000
+CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SYS_PROMPT="Zynq> "
+CONFIG_CMD_THOR_DOWNLOAD=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADFS=y
+CONFIG_CMD_FPGA_LOADMK=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQPL=y
+CONFIG_DM_GPIO=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_XILINX=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xe0001000
+CONFIG_DEBUG_UART_CLOCK=50000000
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
+CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
+CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_FUNCTION_THOR=y
--
1.7.1
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed
2018-05-09 15:56 [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed Ibai Erkiaga
@ 2018-05-10 8:20 ` Michal Simek
2018-05-14 19:43 ` Ibai Erkiaga Elorza
2018-05-14 21:49 ` [U-Boot] [PATCH] " Ibai Erkiaga
2018-05-14 22:43 ` Ibai Erkiaga
2 siblings, 1 reply; 7+ messages in thread
From: Michal Simek @ 2018-05-10 8:20 UTC (permalink / raw)
To: u-boot
On 9.5.2018 17:56, Ibai Erkiaga wrote:
> Initial support for Avnet MiniZed board. Tested UART1 (serial console),
> QSPI(Flash), SDHCI1 (eMMC), USB.
>
> Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> ---
> Changes for v2:
> -board model changed to use Avent prefix
> -usb phy driver changed usb-no-xceiv
> -removed gpio and intc binding
> -fixed-partitions usage
> ---
> U-Boot 2018.05-00023-gdf332c1-dirty (May 09 2018 - 14:50:51 +0100)
>
> Model: Avnet Zynq MiniZed Development Board
> Board: Xilinx Zynq
> Silicon: v3.1
> DRAM: ECC disabled 512 MiB
> MMC: sdhci at e0101000: 0
> Loading Environment from SPI Flash... SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
> OK
> In: serial at e0001000
> Out: serial at e0001000
> Err: serial at e0001000
> Net: No ethernet found.
> Hit any key to stop autoboot: 0
> Zynq> fatls mmc 0
> 16783864 image.ub
> 183 wpa_supplicant.conf
> 1391116 smallboot.bin
>
> 3 file(s), 0 dir(s)
>
> Zynq> sf probe 0 0 0
> SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
> Zynq> usb start
> starting USB...
> USB0: USB EHCI 1.00
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
> Zynq> fatls usb 0
> 12 test.txt
>
> 1 file(s), 0 dir(s)
>
> Zynq>
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/zynq-minized.dts | 104 ++++++++++++++++++++++++++++++++++++++++
> configs/zynq_minized_defconfig | 68 ++++++++++++++++++++++++++
> 3 files changed, 173 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/dts/zynq-minized.dts
> create mode 100644 configs/zynq_minized_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 6fe93a8..5c5f8a8 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
> zynq-cc108.dtb \
> zynq-cse-qspi-single.dtb \
> zynq-microzed.dtb \
> + zynq-minized.dtb \
> zynq-picozed.dtb \
> zynq-syzygy-hub.dtb \
> zynq-topic-miami.dtb \
> diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
> new file mode 100644
> index 0000000..68fe09a
> --- /dev/null
> +++ b/arch/arm/dts/zynq-minized.dts
> @@ -0,0 +1,104 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * dts file for Avnet MiniZed board
> + *
> + * (C) Copyright 2017 - 2018, Xilinx, Inc.
> + *
> + * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> + */
> +
> +/dts-v1/;
> +#include "zynq-7000.dtsi"
> +
> +/ {
> + model = "Avnet Zynq MiniZed Development Board";
> + compatible = "avnet,minized", "xlnx,zynq-7000";
> +
> + aliases {
> + serial0 = &uart1;
> + serial1 = &uart0;
> + spi0 = &qspi;
> + mmc0 = &sdhci0;
> + };
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x20000000>;
> + };
> +
> + chosen {
> + bootargs = "";
> + stdout-path = "serial0:115200n8";
> + };
> +
> + usb_phy0: phy0 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +};
> +
> +&qspi {
> + status = "okay";
> + is-dual = <0>;
> + num-cs = <1>;
> + flash at 0 {
> + compatible = "micron,m25p128";
> + reg = <0x0>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <50000000>;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition at 0 {
> + label = "boot";
> + reg = <0x0 0xff0000>;
> + };
> +
> + partition at 0270000 {
remove this leading zero.
> + label = "kernel";
> + reg = <0x270000 0xd80000>;
> + };
> +
> + partition at ff0000 {
> + label = "bootenv";
> + reg = <0xff0000 0x10000>;
> + };
> +
> + partition at 1000000 {
> + label = "spare";
> + reg = <0x1000000 0x0>;
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + u-boot,dm-pre-reloc;
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> + usb-phy = <&usb_phy0>;
> + usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */ };
}; on next line please.
> +
> +&sdhci1 {
> + status = "okay";
> + non-removable;
> + bus-width = <4>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + mmccard: mmccard at 0 {
> + compatible = "mmc-card";
> + reg = <0>;
> + broken-hpi;
> + };
> +};
> diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
> new file mode 100644
> index 0000000..05cfc0e
> --- /dev/null
> +++ b/configs/zynq_minized_defconfig
> @@ -0,0 +1,68 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_ZYNQ=y
> +CONFIG_SYS_TEXT_BASE=0x4000000
> +CONFIG_SPL=y
> +CONFIG_SPL_STACK_R_ADDR=0x200000
> +CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
> +CONFIG_DEBUG_UART=y
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_FIT=y
> +CONFIG_FIT_SIGNATURE=y
> +CONFIG_FIT_VERBOSE=y
> +CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
> +# CONFIG_DISPLAY_CPUINFO is not set
This should be removed based on
"arm: zynq: Remove checkboard and enable DISPLAY_CPUINFO"
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_OS_BOOT=y
> +CONFIG_SYS_PROMPT="Zynq> "
> +CONFIG_CMD_THOR_DOWNLOAD=y
> +CONFIG_CMD_DFU=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_FPGA_LOADBP=y
> +CONFIG_CMD_FPGA_LOADFS=y
> +CONFIG_CMD_FPGA_LOADMK=y
> +CONFIG_CMD_FPGA_LOADP=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_TFTPPUT=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_OF_EMBED=y
Based on discussion in past this is more for debugging purpose and we
are not enabling it for zynq board.
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_FPGA_XILINX=y
> +CONFIG_FPGA_ZYNQPL=y
> +CONFIG_DM_GPIO=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_ZYNQ=y
> +CONFIG_SPI_FLASH=y
> +CONFIG_SPI_FLASH_BAR=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_SPI_FLASH_WINBOND=y
> +CONFIG_PHY_MARVELL=y
> +CONFIG_PHY_REALTEK=y
> +CONFIG_PHY_XILINX=y
> +CONFIG_ZYNQ_GEM=y
> +CONFIG_DEBUG_UART_ZYNQ=y
> +CONFIG_DEBUG_UART_BASE=0xe0001000
> +CONFIG_DEBUG_UART_CLOCK=50000000
> +CONFIG_ZYNQ_SERIAL=y
> +CONFIG_ZYNQ_QSPI=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_ULPI_VIEWPORT=y
> +CONFIG_USB_ULPI=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
> +CONFIG_CI_UDC=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_USB_FUNCTION_THOR=y
>
The rest looks good.
Thanks,
Michal
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed
2018-05-10 8:20 ` Michal Simek
@ 2018-05-14 19:43 ` Ibai Erkiaga Elorza
0 siblings, 0 replies; 7+ messages in thread
From: Ibai Erkiaga Elorza @ 2018-05-14 19:43 UTC (permalink / raw)
To: u-boot
Hi Michal,
> -----Original Message-----
> From: Michal Simek [mailto:michal.simek at xilinx.com]
> Sent: 10 May 2018 09:21
> To: Ibai Erkiaga Elorza <IBAIE@xilinx.com>; u-boot at lists.denx.de
> Cc: michal.simek at xilinx.com
> Subject: Re: [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed
>
> On 9.5.2018 17:56, Ibai Erkiaga wrote:
> > Initial support for Avnet MiniZed board. Tested UART1 (serial
> > console), QSPI(Flash), SDHCI1 (eMMC), USB.
> >
> > Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> > ---
> > Changes for v2:
> > -board model changed to use Avent prefix
> > -usb phy driver changed usb-no-xceiv
> > -removed gpio and intc binding
> > -fixed-partitions usage
> > ---
> > U-Boot 2018.05-00023-gdf332c1-dirty (May 09 2018 - 14:50:51 +0100)
> >
> > Model: Avnet Zynq MiniZed Development Board
> > Board: Xilinx Zynq
> > Silicon: v3.1
> > DRAM: ECC disabled 512 MiB
> > MMC: sdhci at e0101000: 0
> > Loading Environment from SPI Flash... SF: Detected n25q128 with page
> > size 256 Bytes, erase size 64 KiB, total 16 MiB OK
> > In: serial at e0001000
> > Out: serial at e0001000
> > Err: serial at e0001000
> > Net: No ethernet found.
> > Hit any key to stop autoboot: 0
> > Zynq> fatls mmc 0
> > 16783864 image.ub
> > 183 wpa_supplicant.conf
> > 1391116 smallboot.bin
> >
> > 3 file(s), 0 dir(s)
> >
> > Zynq> sf probe 0 0 0
> > SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB,
> > total 16 MiB
> > Zynq> usb start
> > starting USB...
> > USB0: USB EHCI 1.00
> > scanning bus 0 for devices... 2 USB Device(s) found
> > scanning usb for storage devices... 1 Storage Device(s) found
> > Zynq> fatls usb 0
> > 12 test.txt
> >
> > 1 file(s), 0 dir(s)
> >
> > Zynq>
> > ---
> > arch/arm/dts/Makefile | 1 +
> > arch/arm/dts/zynq-minized.dts | 104
> ++++++++++++++++++++++++++++++++++++++++
> > configs/zynq_minized_defconfig | 68 ++++++++++++++++++++++++++
> > 3 files changed, 173 insertions(+), 0 deletions(-) create mode
> > 100644 arch/arm/dts/zynq-minized.dts create mode 100644
> > configs/zynq_minized_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> > 6fe93a8..5c5f8a8 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
> > zynq-cc108.dtb \
> > zynq-cse-qspi-single.dtb \
> > zynq-microzed.dtb \
> > + zynq-minized.dtb \
> > zynq-picozed.dtb \
> > zynq-syzygy-hub.dtb \
> > zynq-topic-miami.dtb \
> > diff --git a/arch/arm/dts/zynq-minized.dts
> > b/arch/arm/dts/zynq-minized.dts new file mode 100644 index
> > 0000000..68fe09a
> > --- /dev/null
> > +++ b/arch/arm/dts/zynq-minized.dts
> > @@ -0,0 +1,104 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * dts file for Avnet MiniZed board
> > + *
> > + * (C) Copyright 2017 - 2018, Xilinx, Inc.
> > + *
> > + * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> */
> > +
> > +/dts-v1/;
> > +#include "zynq-7000.dtsi"
> > +
> > +/ {
> > + model = "Avnet Zynq MiniZed Development Board";
> > + compatible = "avnet,minized", "xlnx,zynq-7000";
> > +
> > + aliases {
> > + serial0 = &uart1;
> > + serial1 = &uart0;
> > + spi0 = &qspi;
> > + mmc0 = &sdhci0;
> > + };
> > +
> > + memory at 0 {
> > + device_type = "memory";
> > + reg = <0x0 0x20000000>;
> > + };
> > +
> > + chosen {
> > + bootargs = "";
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + usb_phy0: phy0 {
> > + compatible = "usb-nop-xceiv";
> > + #phy-cells = <0>;
> > + };
> > +};
> > +
> > +&qspi {
> > + status = "okay";
> > + is-dual = <0>;
> > + num-cs = <1>;
> > + flash at 0 {
> > + compatible = "micron,m25p128";
> > + reg = <0x0>;
> > + spi-tx-bus-width = <4>;
> > + spi-rx-bus-width = <4>;
> > + spi-max-frequency = <50000000>;
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + partition at 0 {
> > + label = "boot";
> > + reg = <0x0 0xff0000>;
> > + };
> > +
> > + partition at 0270000 {
>
> remove this leading zero.
>
> > + label = "kernel";
> > + reg = <0x270000 0xd80000>;
> > + };
> > +
> > + partition at ff0000 {
> > + label = "bootenv";
> > + reg = <0xff0000 0x10000>;
> > + };
> > +
> > + partition at 1000000 {
> > + label = "spare";
> > + reg = <0x1000000 0x0>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + u-boot,dm-pre-reloc;
> > + status = "okay";
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > + dr_mode = "host";
> > + usb-phy = <&usb_phy0>;
> > + usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */ };
>
> }; on next line please.
>
> > +
> > +&sdhci1 {
> > + status = "okay";
> > + non-removable;
> > + bus-width = <4>;
> > +
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + mmccard: mmccard at 0 {
> > + compatible = "mmc-card";
> > + reg = <0>;
> > + broken-hpi;
> > + };
> > +};
> > diff --git a/configs/zynq_minized_defconfig
> > b/configs/zynq_minized_defconfig new file mode 100644 index
> > 0000000..05cfc0e
> > --- /dev/null
> > +++ b/configs/zynq_minized_defconfig
> > @@ -0,0 +1,68 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_ZYNQ=y
> > +CONFIG_SYS_TEXT_BASE=0x4000000
> > +CONFIG_SPL=y
> > +CONFIG_SPL_STACK_R_ADDR=0x200000
> > +CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
> > +CONFIG_DEBUG_UART=y
> > +CONFIG_DISTRO_DEFAULTS=y
> > +CONFIG_FIT=y
> > +CONFIG_FIT_SIGNATURE=y
> > +CONFIG_FIT_VERBOSE=y
> > +CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
> > +# CONFIG_DISPLAY_CPUINFO is not set
>
> This should be removed based on
> "arm: zynq: Remove checkboard and enable DISPLAY_CPUINFO"
>
>
> > +CONFIG_SPL_STACK_R=y
> > +CONFIG_SPL_OS_BOOT=y
> > +CONFIG_SYS_PROMPT="Zynq> "
> > +CONFIG_CMD_THOR_DOWNLOAD=y
> > +CONFIG_CMD_DFU=y
> > +# CONFIG_CMD_FLASH is not set
> > +CONFIG_CMD_FPGA_LOADBP=y
> > +CONFIG_CMD_FPGA_LOADFS=y
> > +CONFIG_CMD_FPGA_LOADMK=y
> > +CONFIG_CMD_FPGA_LOADP=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_SF=y
> > +CONFIG_CMD_USB=y
> > +# CONFIG_CMD_SETEXPR is not set
> > +CONFIG_CMD_TFTPPUT=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_EXT4_WRITE=y
> > +CONFIG_OF_EMBED=y
>
> Based on discussion in past this is more for debugging purpose and we are
> not enabling it for zynq board.
>
> > +CONFIG_ENV_IS_IN_SPI_FLASH=y
> > +CONFIG_NET_RANDOM_ETHADDR=y
> > +CONFIG_SPL_DM_SEQ_ALIAS=y
> > +CONFIG_DFU_MMC=y
> > +CONFIG_DFU_RAM=y
> > +CONFIG_FPGA_XILINX=y
> > +CONFIG_FPGA_ZYNQPL=y
> > +CONFIG_DM_GPIO=y
> > +CONFIG_MMC_SDHCI=y
> > +CONFIG_MMC_SDHCI_ZYNQ=y
> > +CONFIG_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_BAR=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_SPI_FLASH_WINBOND=y
> > +CONFIG_PHY_MARVELL=y
> > +CONFIG_PHY_REALTEK=y
> > +CONFIG_PHY_XILINX=y
> > +CONFIG_ZYNQ_GEM=y
> > +CONFIG_DEBUG_UART_ZYNQ=y
> > +CONFIG_DEBUG_UART_BASE=0xe0001000
> > +CONFIG_DEBUG_UART_CLOCK=50000000
> > +CONFIG_ZYNQ_SERIAL=y
> > +CONFIG_ZYNQ_QSPI=y
> > +CONFIG_USB=y
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_USB_ULPI_VIEWPORT=y
> > +CONFIG_USB_ULPI=y
> > +CONFIG_USB_STORAGE=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
> > +CONFIG_CI_UDC=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > +CONFIG_USB_FUNCTION_THOR=y
> >
>
> The rest looks good.
>
> Thanks,
> Michal
Ok, I will include those changes and send a new version of the patch.
Regards,
Ibai
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] arm: zynq: Add initial support for Avnet MiniZed
2018-05-09 15:56 [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed Ibai Erkiaga
2018-05-10 8:20 ` Michal Simek
@ 2018-05-14 21:49 ` Ibai Erkiaga
2018-05-15 6:17 ` Michal Simek
2018-05-14 22:43 ` Ibai Erkiaga
2 siblings, 1 reply; 7+ messages in thread
From: Ibai Erkiaga @ 2018-05-14 21:49 UTC (permalink / raw)
To: u-boot
Initial support for Avnet MiniZed board. Tested UART1 (serial console),
QSPI(Flash), SDHCI1 (eMMC), USB.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/zynq-minized.dts | 106 ++++++++++++++++++++++++++++++++++++++++
configs/zynq_minized_defconfig | 66 +++++++++++++++++++++++++
3 files changed, 173 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/dts/zynq-minized.dts
create mode 100644 configs/zynq_minized_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7bec3d6..f7b33f9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-cc108.dtb \
zynq-cse-qspi-single.dtb \
zynq-microzed.dtb \
+ zynq-minized.dtb \
zynq-picozed.dtb \
zynq-syzygy-hub.dtb \
zynq-topic-miami.dtb \
diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
new file mode 100644
index 0000000..525921e
--- /dev/null
+++ b/arch/arm/dts/zynq-minized.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Avnet MiniZed board
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
+ */
+
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ model = "Avnet Zynq MiniZed Development Board";
+ compatible = "avnet,minized", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart0;
+ spi0 = &qspi;
+ mmc0 = &sdhci0;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <0>;
+ num-cs = <1>;
+ flash at 0 {
+ compatible = "micron,m25p128";
+ reg = <0x0>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0xff0000>;
+ };
+
+ partition at 270000 {
+ label = "kernel";
+ reg = <0x270000 0xd80000>;
+ };
+
+ partition at ff0000 {
+ label = "bootenv";
+ reg = <0xff0000 0x10000>;
+ };
+
+ partition at 1000000 {
+ label = "spare";
+ reg = <0x1000000 0x0>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */
+};
+
+&sdhci1 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+ max-frequency = <12000000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard at 0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ broken-hpi;
+ };
+};
diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
new file mode 100644
index 0000000..8cf3215
--- /dev/null
+++ b/configs/zynq_minized_defconfig
@@ -0,0 +1,66 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ZYNQ=y
+CONFIG_SYS_TEXT_BASE=0x4000000
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R_ADDR=0x200000
+CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SYS_PROMPT="Zynq> "
+CONFIG_CMD_THOR_DOWNLOAD=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADFS=y
+CONFIG_CMD_FPGA_LOADMK=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQPL=y
+CONFIG_DM_GPIO=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_XILINX=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xe0001000
+CONFIG_DEBUG_UART_CLOCK=50000000
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
+CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
+CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_FUNCTION_THOR=y
--
1.7.1
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] arm: zynq: Add initial support for Avnet MiniZed
2018-05-09 15:56 [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed Ibai Erkiaga
2018-05-10 8:20 ` Michal Simek
2018-05-14 21:49 ` [U-Boot] [PATCH] " Ibai Erkiaga
@ 2018-05-14 22:43 ` Ibai Erkiaga
2 siblings, 0 replies; 7+ messages in thread
From: Ibai Erkiaga @ 2018-05-14 22:43 UTC (permalink / raw)
To: u-boot
Initial support for Avnet MiniZed board. Tested UART1 (serial console),
QSPI(Flash), SDHCI1 (eMMC), USB.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
---
Changes for v3:
-dts formating refactor
-CONFIG_DISPLAY_CPUINFO removed from config
-CONFIG_OF_EMBED removed from config
Changes for v2:
-board model changed to use Avent prefix
-usb phy driver changed usb-no-xceiv
-removed gpio and intc binding
-fixed-partitions usage
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/zynq-minized.dts | 106 ++++++++++++++++++++++++++++++++++++++++
configs/zynq_minized_defconfig | 66 +++++++++++++++++++++++++
3 files changed, 173 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/dts/zynq-minized.dts
create mode 100644 configs/zynq_minized_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7bec3d6..f7b33f9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-cc108.dtb \
zynq-cse-qspi-single.dtb \
zynq-microzed.dtb \
+ zynq-minized.dtb \
zynq-picozed.dtb \
zynq-syzygy-hub.dtb \
zynq-topic-miami.dtb \
diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
new file mode 100644
index 0000000..525921e
--- /dev/null
+++ b/arch/arm/dts/zynq-minized.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Avnet MiniZed board
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
+ */
+
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ model = "Avnet Zynq MiniZed Development Board";
+ compatible = "avnet,minized", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart0;
+ spi0 = &qspi;
+ mmc0 = &sdhci0;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <0>;
+ num-cs = <1>;
+ flash at 0 {
+ compatible = "micron,m25p128";
+ reg = <0x0>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0xff0000>;
+ };
+
+ partition at 270000 {
+ label = "kernel";
+ reg = <0x270000 0xd80000>;
+ };
+
+ partition at ff0000 {
+ label = "bootenv";
+ reg = <0xff0000 0x10000>;
+ };
+
+ partition at 1000000 {
+ label = "spare";
+ reg = <0x1000000 0x0>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+ usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */
+};
+
+&sdhci1 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+ max-frequency = <12000000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard at 0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ broken-hpi;
+ };
+};
diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
new file mode 100644
index 0000000..8cf3215
--- /dev/null
+++ b/configs/zynq_minized_defconfig
@@ -0,0 +1,66 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ZYNQ=y
+CONFIG_SYS_TEXT_BASE=0x4000000
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R_ADDR=0x200000
+CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SYS_PROMPT="Zynq> "
+CONFIG_CMD_THOR_DOWNLOAD=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADFS=y
+CONFIG_CMD_FPGA_LOADMK=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQPL=y
+CONFIG_DM_GPIO=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_XILINX=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xe0001000
+CONFIG_DEBUG_UART_CLOCK=50000000
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
+CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
+CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_FUNCTION_THOR=y
--
1.7.1
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] arm: zynq: Add initial support for Avnet MiniZed
2018-05-14 21:49 ` [U-Boot] [PATCH] " Ibai Erkiaga
@ 2018-05-15 6:17 ` Michal Simek
0 siblings, 0 replies; 7+ messages in thread
From: Michal Simek @ 2018-05-15 6:17 UTC (permalink / raw)
To: u-boot
On 14.5.2018 23:49, Ibai Erkiaga wrote:
> Initial support for Avnet MiniZed board. Tested UART1 (serial console),
> QSPI(Flash), SDHCI1 (eMMC), USB.
>
> Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/zynq-minized.dts | 106 ++++++++++++++++++++++++++++++++++++++++
> configs/zynq_minized_defconfig | 66 +++++++++++++++++++++++++
> 3 files changed, 173 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/dts/zynq-minized.dts
> create mode 100644 configs/zynq_minized_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 7bec3d6..f7b33f9 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
> zynq-cc108.dtb \
> zynq-cse-qspi-single.dtb \
> zynq-microzed.dtb \
> + zynq-minized.dtb \
> zynq-picozed.dtb \
> zynq-syzygy-hub.dtb \
> zynq-topic-miami.dtb \
> diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
> new file mode 100644
> index 0000000..525921e
> --- /dev/null
> +++ b/arch/arm/dts/zynq-minized.dts
> @@ -0,0 +1,106 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * dts file for Avnet MiniZed board
> + *
> + * (C) Copyright 2017 - 2018, Xilinx, Inc.
> + *
> + * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> + */
> +
> +/dts-v1/;
> +#include "zynq-7000.dtsi"
> +
> +/ {
> + model = "Avnet Zynq MiniZed Development Board";
> + compatible = "avnet,minized", "xlnx,zynq-7000";
> +
> + aliases {
> + serial0 = &uart1;
> + serial1 = &uart0;
> + spi0 = &qspi;
> + mmc0 = &sdhci0;
> + };
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x20000000>;
> + };
> +
> + chosen {
> + bootargs = "";
> + stdout-path = "serial0:115200n8";
> + };
> +
> + usb_phy0: phy0 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +};
> +
> +&qspi {
> + status = "okay";
> + is-dual = <0>;
> + num-cs = <1>;
> + flash at 0 {
> + compatible = "micron,m25p128";
> + reg = <0x0>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <50000000>;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition at 0 {
> + label = "boot";
> + reg = <0x0 0xff0000>;
> + };
> +
> + partition at 270000 {
> + label = "kernel";
> + reg = <0x270000 0xd80000>;
> + };
> +
> + partition at ff0000 {
> + label = "bootenv";
> + reg = <0xff0000 0x10000>;
> + };
> +
> + partition at 1000000 {
> + label = "spare";
> + reg = <0x1000000 0x0>;
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + u-boot,dm-pre-reloc;
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> + usb-phy = <&usb_phy0>;
> + usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */
> +};
> +
> +&sdhci1 {
> + status = "okay";
> + non-removable;
> + bus-width = <4>;
> + max-frequency = <12000000>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + mmccard: mmccard at 0 {
> + compatible = "mmc-card";
> + reg = <0>;
> + broken-hpi;
> + };
> +};
> diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
> new file mode 100644
> index 0000000..8cf3215
> --- /dev/null
> +++ b/configs/zynq_minized_defconfig
> @@ -0,0 +1,66 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_ZYNQ=y
> +CONFIG_SYS_TEXT_BASE=0x4000000
> +CONFIG_SPL=y
> +CONFIG_SPL_STACK_R_ADDR=0x200000
> +CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
> +CONFIG_DEBUG_UART=y
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_FIT=y
> +CONFIG_FIT_SIGNATURE=y
> +CONFIG_FIT_VERBOSE=y
> +CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_OS_BOOT=y
> +CONFIG_SYS_PROMPT="Zynq> "
> +CONFIG_CMD_THOR_DOWNLOAD=y
> +CONFIG_CMD_DFU=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_FPGA_LOADBP=y
> +CONFIG_CMD_FPGA_LOADFS=y
> +CONFIG_CMD_FPGA_LOADMK=y
> +CONFIG_CMD_FPGA_LOADP=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_TFTPPUT=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_FPGA_XILINX=y
> +CONFIG_FPGA_ZYNQPL=y
> +CONFIG_DM_GPIO=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_ZYNQ=y
> +CONFIG_SPI_FLASH=y
> +CONFIG_SPI_FLASH_BAR=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_SPI_FLASH_WINBOND=y
> +CONFIG_PHY_MARVELL=y
> +CONFIG_PHY_REALTEK=y
> +CONFIG_PHY_XILINX=y
> +CONFIG_ZYNQ_GEM=y
> +CONFIG_DEBUG_UART_ZYNQ=y
> +CONFIG_DEBUG_UART_BASE=0xe0001000
> +CONFIG_DEBUG_UART_CLOCK=50000000
> +CONFIG_ZYNQ_SERIAL=y
> +CONFIG_ZYNQ_QSPI=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_ULPI_VIEWPORT=y
> +CONFIG_USB_ULPI=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
> +CONFIG_CI_UDC=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_USB_FUNCTION_THOR=y
>
This is at least v3 without saying that. Please fix your flow and send
regular v3 + changes made there.
Look at tools/patman which can help you with it.
Thanks,
Michal
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] arm: zynq: Add initial support for Avnet MiniZed
[not found] <20180504094019.5968-1-ibai.erkiaga-elorza@xilinx.com>
@ 2018-05-09 12:40 ` Michal Simek
0 siblings, 0 replies; 7+ messages in thread
From: Michal Simek @ 2018-05-09 12:40 UTC (permalink / raw)
To: u-boot
On 4.5.2018 11:40, Ibai Erkiaga wrote:
> Initial support for Avnet MiniZed board. Tested UART1 (serial console),
> QSPI(Flash), SDHCI1 (eMMC), USB.
>
> Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/zynq-minized.dts | 115 ++++++++++++++++++++++++++++++++++++++++
> configs/zynq_minized_defconfig | 68 +++++++++++++++++++++++
> 3 files changed, 184 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/dts/zynq-minized.dts
> create mode 100644 configs/zynq_minized_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index ac7667b..ba1e261 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -131,6 +131,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
> zynq-cc108.dtb \
> zynq-cse-qspi-single.dtb \
> zynq-microzed.dtb \
> + zynq-minized.dtb \
> zynq-picozed.dtb \
> zynq-syzygy-hub.dtb \
> zynq-topic-miami.dtb \
> diff --git a/arch/arm/dts/zynq-minized.dts b/arch/arm/dts/zynq-minized.dts
> new file mode 100644
> index 0000000..ecf1bc0
> --- /dev/null
> +++ b/arch/arm/dts/zynq-minized.dts
> @@ -0,0 +1,115 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * dts file for Avnet MiniZed board
> + *
> + * (C) Copyright 2017 - 2018, Xilinx, Inc.
> + *
> + * Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
> + */
> +
> +/dts-v1/;
> +#include "zynq-7000.dtsi"
> +
> +/ {
> + model = "Zynq MiniZed Development Board";
> + compatible = "xlnx,zynq-zed", "xlnx,zynq-7000";
My patch for adding avnet prefix to kernel was accepted.
That's why use:
model = "Avnet Zynq MiniZed Development Board";
compatible = "avnet,minized", "xlnx,zynq-7000";
> +
> + aliases {
> + serial0 = &uart1;
> + serial1 = &uart0;
> + spi0 = &qspi;
> + mmc0 = &sdhci0;
> + };
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x20000000>;
> + };
> +
> + chosen {
> + bootargs = "";
> + stdout-path = "serial0:115200n8";
> + };
> +
> + usb_phy0: phy0 at e0002000 {
> + compatible = "ulpi-phy";
> + #phy-cells = <0>;
> + reg = <0xe0002000 0x1000>;
> + view-port = <0x0170>;
> + drv-vbus;
> + };
Please check other boards. This ulpi-phy is just in Xilinx git repo.
> +};
> +
> +&gpio0 {
> + emio-gpio-width = <4>;
> + gpio-mask-high = <0x0>;
> + gpio-mask-low = <0x5600>;
This is not the part of binding.
> +};
> +
> +&intc {
> + num_cpus = <2>;
> + num_interrupts = <96>;
this is not the part of kernel intc binding doc.
It looks like qemu binding.
> +};
> +
> +&qspi {
> + status = "okay";
> + is-dual = <0>;
> + num-cs = <1>;
> + flash at 0 {
> + compatible = "micron,m25p128";
> + reg = <0x0>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <50000000>;
> +
please use "fixed-partitions" here.
> + partition at 0x00000000 {
remove 0x from node name and the same below.
> + label = "boot";
> + reg = <0x0 0xff0000>;
> + };
> +
> + partition at 0x00270000 {
> + label = "kernel";
> + reg = <0x270000 0xd80000>;
> + };
> +
> + partition at 0x00ff0000 {
> + label = "bootenv";
> + reg = <0xff0000 0x10000>;
> + };
> +
> + partition at 0x01000000 {
> + label = "spare";
> + reg = <0x1000000 0x0>;
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + u-boot,dm-pre-reloc;
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> + usb-phy = <&usb_phy0>;
> + usb-reset = <&gpio0 7 0>; /* USB_RST_N-MIO7 */
> +};
> +
> +&sdhci1 {
> + status = "okay";
> + non-removable;
> + bus-width= <4>;
missing space.
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + mmccard: mmccard at 0 {
> + compatible = "mmc-card";
> + reg = <0>;
> + broken-hpi;
> + };
> +};
> diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
> new file mode 100644
> index 0000000..05cfc0e
> --- /dev/null
> +++ b/configs/zynq_minized_defconfig
> @@ -0,0 +1,68 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_ZYNQ=y
> +CONFIG_SYS_TEXT_BASE=0x4000000
> +CONFIG_SPL=y
> +CONFIG_SPL_STACK_R_ADDR=0x200000
> +CONFIG_DEFAULT_DEVICE_TREE="zynq-minized"
> +CONFIG_DEBUG_UART=y
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_FIT=y
> +CONFIG_FIT_SIGNATURE=y
> +CONFIG_FIT_VERBOSE=y
> +CONFIG_BOOTCOMMAND="run $modeboot || run distro_bootcmd"
> +# CONFIG_DISPLAY_CPUINFO is not set
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_OS_BOOT=y
> +CONFIG_SYS_PROMPT="Zynq> "
> +CONFIG_CMD_THOR_DOWNLOAD=y
> +CONFIG_CMD_DFU=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_FPGA_LOADBP=y
> +CONFIG_CMD_FPGA_LOADFS=y
> +CONFIG_CMD_FPGA_LOADMK=y
> +CONFIG_CMD_FPGA_LOADP=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_TFTPPUT=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_OF_EMBED=y
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_FPGA_XILINX=y
> +CONFIG_FPGA_ZYNQPL=y
> +CONFIG_DM_GPIO=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_ZYNQ=y
> +CONFIG_SPI_FLASH=y
> +CONFIG_SPI_FLASH_BAR=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_SPI_FLASH_WINBOND=y
> +CONFIG_PHY_MARVELL=y
> +CONFIG_PHY_REALTEK=y
> +CONFIG_PHY_XILINX=y
> +CONFIG_ZYNQ_GEM=y
> +CONFIG_DEBUG_UART_ZYNQ=y
> +CONFIG_DEBUG_UART_BASE=0xe0001000
> +CONFIG_DEBUG_UART_CLOCK=50000000
> +CONFIG_ZYNQ_SERIAL=y
> +CONFIG_ZYNQ_QSPI=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_ULPI_VIEWPORT=y
> +CONFIG_USB_ULPI=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
> +CONFIG_CI_UDC=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_USB_FUNCTION_THOR=y
>
Thanks,
Michal
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2018-05-15 6:17 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-05-09 15:56 [U-Boot] [PATCH v2] arm: zynq: Add initial support for Avnet MiniZed Ibai Erkiaga
2018-05-10 8:20 ` Michal Simek
2018-05-14 19:43 ` Ibai Erkiaga Elorza
2018-05-14 21:49 ` [U-Boot] [PATCH] " Ibai Erkiaga
2018-05-15 6:17 ` Michal Simek
2018-05-14 22:43 ` Ibai Erkiaga
[not found] <20180504094019.5968-1-ibai.erkiaga-elorza@xilinx.com>
2018-05-09 12:40 ` Michal Simek
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.