* [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
@ 2023-01-27 15:05 ` Christian Hewitt
0 siblings, 0 replies; 12+ messages in thread
From: Christian Hewitt @ 2023-01-27 15:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Neil Armstrong, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Christian Hewitt, Krzysztof Kozlowski
The Radxa Zero2 is a small form-factor SBC using the Amlogic
A311D chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes from v1:
- Add Krzysztof's Ack
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 8aa6b6a92c29..6e3cb5a0d879 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -154,6 +154,7 @@ properties:
items:
- enum:
- khadas,vim3
+ - radxa,zero2
- const: amlogic,a311d
- const: amlogic,g12b
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
@ 2023-01-27 15:05 ` Christian Hewitt
0 siblings, 0 replies; 12+ messages in thread
From: Christian Hewitt @ 2023-01-27 15:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Neil Armstrong, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Christian Hewitt, Krzysztof Kozlowski
The Radxa Zero2 is a small form-factor SBC using the Amlogic
A311D chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes from v1:
- Add Krzysztof's Ack
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 8aa6b6a92c29..6e3cb5a0d879 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -154,6 +154,7 @@ properties:
items:
- enum:
- khadas,vim3
+ - radxa,zero2
- const: amlogic,a311d
- const: amlogic,g12b
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
@ 2023-01-27 15:05 ` Christian Hewitt
0 siblings, 0 replies; 12+ messages in thread
From: Christian Hewitt @ 2023-01-27 15:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Neil Armstrong, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Krzysztof Kozlowski
The Radxa Zero2 is a small form-factor SBC using the Amlogic
A311D chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes from v1:
- Add Krzysztof's Ack
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 8aa6b6a92c29..6e3cb5a0d879 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -154,6 +154,7 @@ properties:
items:
- enum:
- khadas,vim3
+ - radxa,zero2
- const: amlogic,a311d
- const: amlogic,g12b
--
2.34.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 2/2] arm64: dts: meson: add support for Radxa Zero2
2023-01-27 15:05 ` Christian Hewitt
(?)
@ 2023-01-27 15:05 ` Christian Hewitt
-1 siblings, 0 replies; 12+ messages in thread
From: Christian Hewitt @ 2023-01-27 15:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Neil Armstrong, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Christian Hewitt, Yuntian Zhang
From: Yuntian Zhang <yt@radxa.com>
Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
chipset that ships in a number of eMMC configurations:
- Amlogic A311D (Quad A73 + Dual A53) CPU
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- Mali G52-MP4 GPU
- HDMI 2.1 output (micro)
- BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Yuntian Zhang <yt@radxa.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
The original dts from Yuntian contains some additional content for
the USB-C device, but this is not working for me so I have ommited
it and kept things simple. I've also left out some pwm-fan/thermal
content; while the board does not ship with a fan the A311D chip
should be used with one and I believe the board has a connector to
add a fan, but until this is confirmed (and production boards are
available) it's best left out.
Changes from v1:
- Corrected underscores in node names
- Corrected wifi32k clock node name
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-radxa-zero2.dts | 489 ++++++++++++++++++
2 files changed, 490 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 04114e8c9992..bb1af1d80c21 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
new file mode 100644
index 000000000000..9a60c5ec2072
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ * Copyright (c) 2022 Radxa Limited
+ * Author: Yuntian Zhang <yt@radxa.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-a311d.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
+ model = "Radxa Zero2";
+
+ aliases {
+ serial0 = &uart_AO;
+ serial2 = &uart_A;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+ power-button {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ ao_5v: regulator-ao-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "AO_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vddao_1v8: regulator-vddao-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&ao_5v>;
+ regulator-always-on;
+ };
+
+ vddcpu_a: regulator-vddcpu-a {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_A";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&ao_5v>;
+
+ pwms = <&pwm_ab 0 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddcpu_b: regulator-vddcpu-b {
+ /*
+ * Silergy SY8120B1ABC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_B";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&ao_5v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "RADXA-ZERO2";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-4 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+
+ wifi32k: clock-0 {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&gpio {
+ gpio-line-names =
+ /* GPIOZ */
+ "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
+ "", "", "", "", "", "", "", "",
+ /* GPIOH */
+ "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
+ "",
+ /* BOOT */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "EMMC_PWRSEQ", "", "", "",
+ /* GPIOC */
+ "", "", "", "", "", "", "SD_CD", "PIN_36",
+ /* GPIOA */
+ "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
+ "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
+ /* GPIOX */
+ "", "", "", "", "", "", "SDIO_PWRSEQ", "",
+ "", "", "", "", "", "", "", "",
+ "", "BT_SHUTDOWN", "", "";
+};
+
+&gpio_ao {
+ gpio-line-names =
+ /* GPIOAO */
+ "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
+ "PIN_33", "PIN_37", "FAN", "",
+ /* GPIOE */
+ "", "", "";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&ao_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "disabled";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ pinctrl-0 = <&pwm_a_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_ef {
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin2";
+ status = "okay";
+};
+
+&pwm_AO_ab {
+ pinctrl-0 = <&pwm_ao_a_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin3";
+ status = "okay";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin4";
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddao_1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_1v8>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 2/2] arm64: dts: meson: add support for Radxa Zero2
@ 2023-01-27 15:05 ` Christian Hewitt
0 siblings, 0 replies; 12+ messages in thread
From: Christian Hewitt @ 2023-01-27 15:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Neil Armstrong, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Christian Hewitt, Yuntian Zhang
From: Yuntian Zhang <yt@radxa.com>
Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
chipset that ships in a number of eMMC configurations:
- Amlogic A311D (Quad A73 + Dual A53) CPU
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- Mali G52-MP4 GPU
- HDMI 2.1 output (micro)
- BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Yuntian Zhang <yt@radxa.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
The original dts from Yuntian contains some additional content for
the USB-C device, but this is not working for me so I have ommited
it and kept things simple. I've also left out some pwm-fan/thermal
content; while the board does not ship with a fan the A311D chip
should be used with one and I believe the board has a connector to
add a fan, but until this is confirmed (and production boards are
available) it's best left out.
Changes from v1:
- Corrected underscores in node names
- Corrected wifi32k clock node name
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-radxa-zero2.dts | 489 ++++++++++++++++++
2 files changed, 490 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 04114e8c9992..bb1af1d80c21 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
new file mode 100644
index 000000000000..9a60c5ec2072
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ * Copyright (c) 2022 Radxa Limited
+ * Author: Yuntian Zhang <yt@radxa.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-a311d.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
+ model = "Radxa Zero2";
+
+ aliases {
+ serial0 = &uart_AO;
+ serial2 = &uart_A;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+ power-button {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ ao_5v: regulator-ao-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "AO_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vddao_1v8: regulator-vddao-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&ao_5v>;
+ regulator-always-on;
+ };
+
+ vddcpu_a: regulator-vddcpu-a {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_A";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&ao_5v>;
+
+ pwms = <&pwm_ab 0 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddcpu_b: regulator-vddcpu-b {
+ /*
+ * Silergy SY8120B1ABC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_B";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&ao_5v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "RADXA-ZERO2";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-4 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+
+ wifi32k: clock-0 {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&gpio {
+ gpio-line-names =
+ /* GPIOZ */
+ "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
+ "", "", "", "", "", "", "", "",
+ /* GPIOH */
+ "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
+ "",
+ /* BOOT */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "EMMC_PWRSEQ", "", "", "",
+ /* GPIOC */
+ "", "", "", "", "", "", "SD_CD", "PIN_36",
+ /* GPIOA */
+ "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
+ "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
+ /* GPIOX */
+ "", "", "", "", "", "", "SDIO_PWRSEQ", "",
+ "", "", "", "", "", "", "", "",
+ "", "BT_SHUTDOWN", "", "";
+};
+
+&gpio_ao {
+ gpio-line-names =
+ /* GPIOAO */
+ "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
+ "PIN_33", "PIN_37", "FAN", "",
+ /* GPIOE */
+ "", "", "";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&ao_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "disabled";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ pinctrl-0 = <&pwm_a_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_ef {
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin2";
+ status = "okay";
+};
+
+&pwm_AO_ab {
+ pinctrl-0 = <&pwm_ao_a_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin3";
+ status = "okay";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin4";
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddao_1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_1v8>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 2/2] arm64: dts: meson: add support for Radxa Zero2
@ 2023-01-27 15:05 ` Christian Hewitt
0 siblings, 0 replies; 12+ messages in thread
From: Christian Hewitt @ 2023-01-27 15:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Neil Armstrong, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Yuntian Zhang
From: Yuntian Zhang <yt@radxa.com>
Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
chipset that ships in a number of eMMC configurations:
- Amlogic A311D (Quad A73 + Dual A53) CPU
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- Mali G52-MP4 GPU
- HDMI 2.1 output (micro)
- BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Yuntian Zhang <yt@radxa.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
The original dts from Yuntian contains some additional content for
the USB-C device, but this is not working for me so I have ommited
it and kept things simple. I've also left out some pwm-fan/thermal
content; while the board does not ship with a fan the A311D chip
should be used with one and I believe the board has a connector to
add a fan, but until this is confirmed (and production boards are
available) it's best left out.
Changes from v1:
- Corrected underscores in node names
- Corrected wifi32k clock node name
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-radxa-zero2.dts | 489 ++++++++++++++++++
2 files changed, 490 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 04114e8c9992..bb1af1d80c21 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
new file mode 100644
index 000000000000..9a60c5ec2072
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ * Copyright (c) 2022 Radxa Limited
+ * Author: Yuntian Zhang <yt@radxa.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-a311d.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
+ model = "Radxa Zero2";
+
+ aliases {
+ serial0 = &uart_AO;
+ serial2 = &uart_A;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+ power-button {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ ao_5v: regulator-ao-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "AO_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vddao_1v8: regulator-vddao-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&ao_5v>;
+ regulator-always-on;
+ };
+
+ vddcpu_a: regulator-vddcpu-a {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_A";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&ao_5v>;
+
+ pwms = <&pwm_ab 0 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddcpu_b: regulator-vddcpu-b {
+ /*
+ * Silergy SY8120B1ABC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_B";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&ao_5v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "RADXA-ZERO2";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-4 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+
+ wifi32k: clock-0 {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&gpio {
+ gpio-line-names =
+ /* GPIOZ */
+ "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
+ "", "", "", "", "", "", "", "",
+ /* GPIOH */
+ "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
+ "",
+ /* BOOT */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "EMMC_PWRSEQ", "", "", "",
+ /* GPIOC */
+ "", "", "", "", "", "", "SD_CD", "PIN_36",
+ /* GPIOA */
+ "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
+ "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
+ /* GPIOX */
+ "", "", "", "", "", "", "SDIO_PWRSEQ", "",
+ "", "", "", "", "", "", "", "",
+ "", "BT_SHUTDOWN", "", "";
+};
+
+&gpio_ao {
+ gpio-line-names =
+ /* GPIOAO */
+ "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
+ "PIN_33", "PIN_37", "FAN", "",
+ /* GPIOE */
+ "", "", "";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&ao_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "disabled";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ pinctrl-0 = <&pwm_a_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_ef {
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin2";
+ status = "okay";
+};
+
+&pwm_AO_ab {
+ pinctrl-0 = <&pwm_ao_a_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin3";
+ status = "okay";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin4";
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddao_1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_1v8>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
--
2.34.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: meson: add support for Radxa Zero2
2023-01-27 15:05 ` Christian Hewitt
(?)
@ 2023-01-27 16:25 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2023-01-27 16:25 UTC (permalink / raw)
To: Christian Hewitt, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Yuntian Zhang
On 27/01/2023 16:05, Christian Hewitt wrote:
> From: Yuntian Zhang <yt@radxa.com>
>
> Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
> chipset that ships in a number of eMMC configurations:
>
> - Amlogic A311D (Quad A73 + Dual A53) CPU
> - 4GB LPDDR4 RAM
> - 32/64/128GB eMMC
> - Mali G52-MP4 GPU
> - HDMI 2.1 output (micro)
> - BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
> - 1x USB 2.0 port - Type C (OTG)
> - 1x USB 3.0 port - Type C (Host)
> - 1x micro SD Card slot
> - 40 Pin GPIO header
>
> Signed-off-by: Yuntian Zhang <yt@radxa.com>
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
> The original dts from Yuntian contains some additional content for
> the USB-C device, but this is not working for me so I have ommited
> it and kept things simple. I've also left out some pwm-fan/thermal
> content; while the board does not ship with a fan the A311D chip
> should be used with one and I believe the board has a connector to
> add a fan, but until this is confirmed (and production boards are
> available) it's best left out.
>
> Changes from v1:
> - Corrected underscores in node names
> - Corrected wifi32k clock node name
>
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../dts/amlogic/meson-g12b-radxa-zero2.dts | 489 ++++++++++++++++++
> 2 files changed, 490 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 04114e8c9992..bb1af1d80c21 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
> new file mode 100644
> index 000000000000..9a60c5ec2072
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
> @@ -0,0 +1,489 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
> + * Copyright (c) 2022 Radxa Limited
> + * Author: Yuntian Zhang <yt@radxa.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-g12b-a311d.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/gpio/meson-g12a-gpio.h>
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> + compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
> + model = "Radxa Zero2";
> +
> + aliases {
> + serial0 = &uart_AO;
> + serial2 = &uart_A;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + poll-interval = <100>;
> + power-button {
> + label = "power";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_tmds_out>;
> + };
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + ao_5v: regulator-ao-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "AO_5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v8: regulator-vcc-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3: regulator-vcc-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + /* FIXME: actually controlled by VDDCPU_B_EN */
> + };
> +
> + vddao_1v8: regulator-vddao-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ao_5v>;
> + regulator-always-on;
> + };
> +
> + vddcpu_a: regulator-vddcpu-a {
> + /*
> + * MP8756GD Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_A";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_ab 0 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vddcpu_b: regulator-vddcpu-b {
> + /*
> + * Silergy SY8120B1ABC Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_B";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_AO_cd 1 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "amlogic,axg-sound-card";
> + model = "RADXA-ZERO2";
> + audio-aux-devs = <&tdmout_b>;
> + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> + "TDMOUT_B IN 1", "FRDDR_B OUT 1",
> + "TDMOUT_B IN 2", "FRDDR_C OUT 1",
> + "TDM_B Playback", "TDMOUT_B OUT";
> +
> + assigned-clocks = <&clkc CLKID_MPLL2>,
> + <&clkc CLKID_MPLL0>,
> + <&clkc CLKID_MPLL1>;
> + assigned-clock-parents = <0>, <0>, <0>;
> + assigned-clock-rates = <294912000>,
> + <270950400>,
> + <393216000>;
> +
> + dai-link-0 {
> + sound-dai = <&frddr_a>;
> + };
> +
> + dai-link-1 {
> + sound-dai = <&frddr_b>;
> + };
> +
> + dai-link-2 {
> + sound-dai = <&frddr_c>;
> + };
> +
> + /* 8ch hdmi interface */
> + dai-link-3 {
> + sound-dai = <&tdmif_b>;
> + dai-format = "i2s";
> + dai-tdm-slot-tx-mask-0 = <1 1>;
> + dai-tdm-slot-tx-mask-1 = <1 1>;
> + dai-tdm-slot-tx-mask-2 = <1 1>;
> + dai-tdm-slot-tx-mask-3 = <1 1>;
> + mclk-fs = <256>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> + };
> + };
> +
> + /* hdmi glue */
> + dai-link-4 {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> + codec {
> + sound-dai = <&hdmi_tx>;
> + };
> + };
> + };
> +
> + wifi32k: clock-0 {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +};
> +
> +&arb {
> + status = "okay";
> +};
> +
> +&cec_AO {
> + pinctrl-0 = <&cec_ao_a_h_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cecb_AO {
> + pinctrl-0 = <&cec_ao_b_h_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&clkc_audio {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vddcpu_b>;
> + operating-points-v2 = <&cpu_opp_table_0>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vddcpu_b>;
> + operating-points-v2 = <&cpu_opp_table_0>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu100 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu101 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu102 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu103 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&frddr_a {
> + status = "okay";
> +};
> +
> +&frddr_b {
> + status = "okay";
> +};
> +
> +&frddr_c {
> + status = "okay";
> +};
> +
> +&gpio {
> + gpio-line-names =
> + /* GPIOZ */
> + "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
> + "", "", "", "", "", "", "", "",
> + /* GPIOH */
> + "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
> + "",
> + /* BOOT */
> + "", "", "", "", "", "", "", "",
> + "", "", "", "", "EMMC_PWRSEQ", "", "", "",
> + /* GPIOC */
> + "", "", "", "", "", "", "SD_CD", "PIN_36",
> + /* GPIOA */
> + "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
> + "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
> + /* GPIOX */
> + "", "", "", "", "", "", "SDIO_PWRSEQ", "",
> + "", "", "", "", "", "", "", "",
> + "", "BT_SHUTDOWN", "", "";
> +};
> +
> +&gpio_ao {
> + gpio-line-names =
> + /* GPIOAO */
> + "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
> + "PIN_33", "PIN_37", "FAN", "",
> + /* GPIOE */
> + "", "", "";
> +};
> +
> +&hdmi_tx {
> + status = "okay";
> + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
> + pinctrl-names = "default";
> + hdmi-supply = <&ao_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> + hdmi_tx_tmds_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> +};
> +
> +&ir {
> + status = "disabled";
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> + pinctrl-0 = <&pwm_a_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
> +&pwm_ef {
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin2";
> + status = "okay";
> +};
> +
> +&pwm_AO_ab {
> + pinctrl-0 = <&pwm_ao_a_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin3";
> + status = "okay";
> +};
> +
> +&pwm_AO_cd {
> + pinctrl-0 = <&pwm_ao_d_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin4";
> + status = "okay";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vddao_1v8>;
> +};
> +
> +/* SDIO */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + /* WiFi firmware requires power to be kept while in suspend */
> + keep-power-in-suspend;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_1v8>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_c_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_c_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <50000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_3v3>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + max-frequency = <200000000>;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> +};
> +
> +&tdmif_b {
> + status = "okay";
> +};
> +
> +&tdmout_b {
> + status = "okay";
> +};
> +
> +&tohdmitx {
> + status = "okay";
> +};
> +
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
> + max-speed = <2000000>;
> + clocks = <&wifi32k>;
> + clock-names = "lpo";
> + };
> +};
> +
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> +};
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: meson: add support for Radxa Zero2
@ 2023-01-27 16:25 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2023-01-27 16:25 UTC (permalink / raw)
To: Christian Hewitt, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Yuntian Zhang
On 27/01/2023 16:05, Christian Hewitt wrote:
> From: Yuntian Zhang <yt@radxa.com>
>
> Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
> chipset that ships in a number of eMMC configurations:
>
> - Amlogic A311D (Quad A73 + Dual A53) CPU
> - 4GB LPDDR4 RAM
> - 32/64/128GB eMMC
> - Mali G52-MP4 GPU
> - HDMI 2.1 output (micro)
> - BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
> - 1x USB 2.0 port - Type C (OTG)
> - 1x USB 3.0 port - Type C (Host)
> - 1x micro SD Card slot
> - 40 Pin GPIO header
>
> Signed-off-by: Yuntian Zhang <yt@radxa.com>
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
> The original dts from Yuntian contains some additional content for
> the USB-C device, but this is not working for me so I have ommited
> it and kept things simple. I've also left out some pwm-fan/thermal
> content; while the board does not ship with a fan the A311D chip
> should be used with one and I believe the board has a connector to
> add a fan, but until this is confirmed (and production boards are
> available) it's best left out.
>
> Changes from v1:
> - Corrected underscores in node names
> - Corrected wifi32k clock node name
>
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../dts/amlogic/meson-g12b-radxa-zero2.dts | 489 ++++++++++++++++++
> 2 files changed, 490 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 04114e8c9992..bb1af1d80c21 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
> new file mode 100644
> index 000000000000..9a60c5ec2072
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
> @@ -0,0 +1,489 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
> + * Copyright (c) 2022 Radxa Limited
> + * Author: Yuntian Zhang <yt@radxa.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-g12b-a311d.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/gpio/meson-g12a-gpio.h>
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> + compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
> + model = "Radxa Zero2";
> +
> + aliases {
> + serial0 = &uart_AO;
> + serial2 = &uart_A;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + poll-interval = <100>;
> + power-button {
> + label = "power";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_tmds_out>;
> + };
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + ao_5v: regulator-ao-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "AO_5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v8: regulator-vcc-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3: regulator-vcc-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + /* FIXME: actually controlled by VDDCPU_B_EN */
> + };
> +
> + vddao_1v8: regulator-vddao-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ao_5v>;
> + regulator-always-on;
> + };
> +
> + vddcpu_a: regulator-vddcpu-a {
> + /*
> + * MP8756GD Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_A";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_ab 0 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vddcpu_b: regulator-vddcpu-b {
> + /*
> + * Silergy SY8120B1ABC Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_B";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_AO_cd 1 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "amlogic,axg-sound-card";
> + model = "RADXA-ZERO2";
> + audio-aux-devs = <&tdmout_b>;
> + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> + "TDMOUT_B IN 1", "FRDDR_B OUT 1",
> + "TDMOUT_B IN 2", "FRDDR_C OUT 1",
> + "TDM_B Playback", "TDMOUT_B OUT";
> +
> + assigned-clocks = <&clkc CLKID_MPLL2>,
> + <&clkc CLKID_MPLL0>,
> + <&clkc CLKID_MPLL1>;
> + assigned-clock-parents = <0>, <0>, <0>;
> + assigned-clock-rates = <294912000>,
> + <270950400>,
> + <393216000>;
> +
> + dai-link-0 {
> + sound-dai = <&frddr_a>;
> + };
> +
> + dai-link-1 {
> + sound-dai = <&frddr_b>;
> + };
> +
> + dai-link-2 {
> + sound-dai = <&frddr_c>;
> + };
> +
> + /* 8ch hdmi interface */
> + dai-link-3 {
> + sound-dai = <&tdmif_b>;
> + dai-format = "i2s";
> + dai-tdm-slot-tx-mask-0 = <1 1>;
> + dai-tdm-slot-tx-mask-1 = <1 1>;
> + dai-tdm-slot-tx-mask-2 = <1 1>;
> + dai-tdm-slot-tx-mask-3 = <1 1>;
> + mclk-fs = <256>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> + };
> + };
> +
> + /* hdmi glue */
> + dai-link-4 {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> + codec {
> + sound-dai = <&hdmi_tx>;
> + };
> + };
> + };
> +
> + wifi32k: clock-0 {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +};
> +
> +&arb {
> + status = "okay";
> +};
> +
> +&cec_AO {
> + pinctrl-0 = <&cec_ao_a_h_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cecb_AO {
> + pinctrl-0 = <&cec_ao_b_h_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&clkc_audio {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vddcpu_b>;
> + operating-points-v2 = <&cpu_opp_table_0>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vddcpu_b>;
> + operating-points-v2 = <&cpu_opp_table_0>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu100 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu101 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu102 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu103 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&frddr_a {
> + status = "okay";
> +};
> +
> +&frddr_b {
> + status = "okay";
> +};
> +
> +&frddr_c {
> + status = "okay";
> +};
> +
> +&gpio {
> + gpio-line-names =
> + /* GPIOZ */
> + "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
> + "", "", "", "", "", "", "", "",
> + /* GPIOH */
> + "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
> + "",
> + /* BOOT */
> + "", "", "", "", "", "", "", "",
> + "", "", "", "", "EMMC_PWRSEQ", "", "", "",
> + /* GPIOC */
> + "", "", "", "", "", "", "SD_CD", "PIN_36",
> + /* GPIOA */
> + "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
> + "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
> + /* GPIOX */
> + "", "", "", "", "", "", "SDIO_PWRSEQ", "",
> + "", "", "", "", "", "", "", "",
> + "", "BT_SHUTDOWN", "", "";
> +};
> +
> +&gpio_ao {
> + gpio-line-names =
> + /* GPIOAO */
> + "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
> + "PIN_33", "PIN_37", "FAN", "",
> + /* GPIOE */
> + "", "", "";
> +};
> +
> +&hdmi_tx {
> + status = "okay";
> + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
> + pinctrl-names = "default";
> + hdmi-supply = <&ao_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> + hdmi_tx_tmds_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> +};
> +
> +&ir {
> + status = "disabled";
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> + pinctrl-0 = <&pwm_a_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
> +&pwm_ef {
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin2";
> + status = "okay";
> +};
> +
> +&pwm_AO_ab {
> + pinctrl-0 = <&pwm_ao_a_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin3";
> + status = "okay";
> +};
> +
> +&pwm_AO_cd {
> + pinctrl-0 = <&pwm_ao_d_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin4";
> + status = "okay";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vddao_1v8>;
> +};
> +
> +/* SDIO */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + /* WiFi firmware requires power to be kept while in suspend */
> + keep-power-in-suspend;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_1v8>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_c_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_c_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <50000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_3v3>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + max-frequency = <200000000>;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> +};
> +
> +&tdmif_b {
> + status = "okay";
> +};
> +
> +&tdmout_b {
> + status = "okay";
> +};
> +
> +&tohdmitx {
> + status = "okay";
> +};
> +
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
> + max-speed = <2000000>;
> + clocks = <&wifi32k>;
> + clock-names = "lpo";
> + };
> +};
> +
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> +};
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: meson: add support for Radxa Zero2
@ 2023-01-27 16:25 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2023-01-27 16:25 UTC (permalink / raw)
To: Christian Hewitt, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Jerome Brunet, Martin Blumenstingl, devicetree, linux-arm-kernel,
linux-amlogic, linux-kernel
Cc: Yuntian Zhang
On 27/01/2023 16:05, Christian Hewitt wrote:
> From: Yuntian Zhang <yt@radxa.com>
>
> Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
> chipset that ships in a number of eMMC configurations:
>
> - Amlogic A311D (Quad A73 + Dual A53) CPU
> - 4GB LPDDR4 RAM
> - 32/64/128GB eMMC
> - Mali G52-MP4 GPU
> - HDMI 2.1 output (micro)
> - BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
> - 1x USB 2.0 port - Type C (OTG)
> - 1x USB 3.0 port - Type C (Host)
> - 1x micro SD Card slot
> - 40 Pin GPIO header
>
> Signed-off-by: Yuntian Zhang <yt@radxa.com>
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
> The original dts from Yuntian contains some additional content for
> the USB-C device, but this is not working for me so I have ommited
> it and kept things simple. I've also left out some pwm-fan/thermal
> content; while the board does not ship with a fan the A311D chip
> should be used with one and I believe the board has a connector to
> add a fan, but until this is confirmed (and production boards are
> available) it's best left out.
>
> Changes from v1:
> - Corrected underscores in node names
> - Corrected wifi32k clock node name
>
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../dts/amlogic/meson-g12b-radxa-zero2.dts | 489 ++++++++++++++++++
> 2 files changed, 490 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 04114e8c9992..bb1af1d80c21 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
> new file mode 100644
> index 000000000000..9a60c5ec2072
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
> @@ -0,0 +1,489 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
> + * Copyright (c) 2022 Radxa Limited
> + * Author: Yuntian Zhang <yt@radxa.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-g12b-a311d.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/gpio/meson-g12a-gpio.h>
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> + compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
> + model = "Radxa Zero2";
> +
> + aliases {
> + serial0 = &uart_AO;
> + serial2 = &uart_A;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + poll-interval = <100>;
> + power-button {
> + label = "power";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_tmds_out>;
> + };
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + ao_5v: regulator-ao-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "AO_5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v8: regulator-vcc-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3: regulator-vcc-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + /* FIXME: actually controlled by VDDCPU_B_EN */
> + };
> +
> + vddao_1v8: regulator-vddao-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ao_5v>;
> + regulator-always-on;
> + };
> +
> + vddcpu_a: regulator-vddcpu-a {
> + /*
> + * MP8756GD Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_A";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_ab 0 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vddcpu_b: regulator-vddcpu-b {
> + /*
> + * Silergy SY8120B1ABC Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_B";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_AO_cd 1 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "amlogic,axg-sound-card";
> + model = "RADXA-ZERO2";
> + audio-aux-devs = <&tdmout_b>;
> + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> + "TDMOUT_B IN 1", "FRDDR_B OUT 1",
> + "TDMOUT_B IN 2", "FRDDR_C OUT 1",
> + "TDM_B Playback", "TDMOUT_B OUT";
> +
> + assigned-clocks = <&clkc CLKID_MPLL2>,
> + <&clkc CLKID_MPLL0>,
> + <&clkc CLKID_MPLL1>;
> + assigned-clock-parents = <0>, <0>, <0>;
> + assigned-clock-rates = <294912000>,
> + <270950400>,
> + <393216000>;
> +
> + dai-link-0 {
> + sound-dai = <&frddr_a>;
> + };
> +
> + dai-link-1 {
> + sound-dai = <&frddr_b>;
> + };
> +
> + dai-link-2 {
> + sound-dai = <&frddr_c>;
> + };
> +
> + /* 8ch hdmi interface */
> + dai-link-3 {
> + sound-dai = <&tdmif_b>;
> + dai-format = "i2s";
> + dai-tdm-slot-tx-mask-0 = <1 1>;
> + dai-tdm-slot-tx-mask-1 = <1 1>;
> + dai-tdm-slot-tx-mask-2 = <1 1>;
> + dai-tdm-slot-tx-mask-3 = <1 1>;
> + mclk-fs = <256>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> + };
> + };
> +
> + /* hdmi glue */
> + dai-link-4 {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> + codec {
> + sound-dai = <&hdmi_tx>;
> + };
> + };
> + };
> +
> + wifi32k: clock-0 {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +};
> +
> +&arb {
> + status = "okay";
> +};
> +
> +&cec_AO {
> + pinctrl-0 = <&cec_ao_a_h_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cecb_AO {
> + pinctrl-0 = <&cec_ao_b_h_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&clkc_audio {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vddcpu_b>;
> + operating-points-v2 = <&cpu_opp_table_0>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vddcpu_b>;
> + operating-points-v2 = <&cpu_opp_table_0>;
> + clocks = <&clkc CLKID_CPU_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu100 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu101 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu102 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&cpu103 {
> + cpu-supply = <&vddcpu_a>;
> + operating-points-v2 = <&cpub_opp_table_1>;
> + clocks = <&clkc CLKID_CPUB_CLK>;
> + clock-latency = <50000>;
> +};
> +
> +&frddr_a {
> + status = "okay";
> +};
> +
> +&frddr_b {
> + status = "okay";
> +};
> +
> +&frddr_c {
> + status = "okay";
> +};
> +
> +&gpio {
> + gpio-line-names =
> + /* GPIOZ */
> + "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
> + "", "", "", "", "", "", "", "",
> + /* GPIOH */
> + "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
> + "",
> + /* BOOT */
> + "", "", "", "", "", "", "", "",
> + "", "", "", "", "EMMC_PWRSEQ", "", "", "",
> + /* GPIOC */
> + "", "", "", "", "", "", "SD_CD", "PIN_36",
> + /* GPIOA */
> + "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
> + "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
> + /* GPIOX */
> + "", "", "", "", "", "", "SDIO_PWRSEQ", "",
> + "", "", "", "", "", "", "", "",
> + "", "BT_SHUTDOWN", "", "";
> +};
> +
> +&gpio_ao {
> + gpio-line-names =
> + /* GPIOAO */
> + "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
> + "PIN_33", "PIN_37", "FAN", "",
> + /* GPIOE */
> + "", "", "";
> +};
> +
> +&hdmi_tx {
> + status = "okay";
> + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
> + pinctrl-names = "default";
> + hdmi-supply = <&ao_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> + hdmi_tx_tmds_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> +};
> +
> +&ir {
> + status = "disabled";
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> + pinctrl-0 = <&pwm_a_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
> +&pwm_ef {
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin2";
> + status = "okay";
> +};
> +
> +&pwm_AO_ab {
> + pinctrl-0 = <&pwm_ao_a_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin3";
> + status = "okay";
> +};
> +
> +&pwm_AO_cd {
> + pinctrl-0 = <&pwm_ao_d_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin4";
> + status = "okay";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vddao_1v8>;
> +};
> +
> +/* SDIO */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + /* WiFi firmware requires power to be kept while in suspend */
> + keep-power-in-suspend;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_1v8>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_c_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_c_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <50000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_3v3>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + max-frequency = <200000000>;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> +};
> +
> +&tdmif_b {
> + status = "okay";
> +};
> +
> +&tdmout_b {
> + status = "okay";
> +};
> +
> +&tohdmitx {
> + status = "okay";
> +};
> +
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
> + max-speed = <2000000>;
> + clocks = <&wifi32k>;
> + clock-names = "lpo";
> + };
> +};
> +
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> +};
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
2023-01-27 15:05 ` Christian Hewitt
(?)
@ 2023-01-27 17:02 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2023-01-27 17:02 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl, devicetree, linux-arm-kernel, linux-amlogic,
linux-kernel, Christian Hewitt
Cc: Krzysztof Kozlowski
Hi,
On Fri, 27 Jan 2023 15:05:35 +0000, Christian Hewitt wrote:
> The Radxa Zero2 is a small form-factor SBC using the Amlogic
> A311D chip.
>
>
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.3/arm64-dt)
[1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
https://git.kernel.org/amlogic/c/229cfc6b16ccedfcae1ee10dc1aed04e7a85ed32
[2/2] arm64: dts: meson: add support for Radxa Zero2
https://git.kernel.org/amlogic/c/d747e7f76a5fa6e3deb4c419df768f9ee49c2161
These changes has been applied on the intermediate git tree [1].
The v6.3/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
@ 2023-01-27 17:02 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2023-01-27 17:02 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl, devicetree, linux-arm-kernel, linux-amlogic,
linux-kernel, Christian Hewitt
Cc: Krzysztof Kozlowski
Hi,
On Fri, 27 Jan 2023 15:05:35 +0000, Christian Hewitt wrote:
> The Radxa Zero2 is a small form-factor SBC using the Amlogic
> A311D chip.
>
>
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.3/arm64-dt)
[1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
https://git.kernel.org/amlogic/c/229cfc6b16ccedfcae1ee10dc1aed04e7a85ed32
[2/2] arm64: dts: meson: add support for Radxa Zero2
https://git.kernel.org/amlogic/c/d747e7f76a5fa6e3deb4c419df768f9ee49c2161
These changes has been applied on the intermediate git tree [1].
The v6.3/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
@ 2023-01-27 17:02 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2023-01-27 17:02 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl, devicetree, linux-arm-kernel, linux-amlogic,
linux-kernel, Christian Hewitt
Cc: Krzysztof Kozlowski
Hi,
On Fri, 27 Jan 2023 15:05:35 +0000, Christian Hewitt wrote:
> The Radxa Zero2 is a small form-factor SBC using the Amlogic
> A311D chip.
>
>
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.3/arm64-dt)
[1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2
https://git.kernel.org/amlogic/c/229cfc6b16ccedfcae1ee10dc1aed04e7a85ed32
[2/2] arm64: dts: meson: add support for Radxa Zero2
https://git.kernel.org/amlogic/c/d747e7f76a5fa6e3deb4c419df768f9ee49c2161
These changes has been applied on the intermediate git tree [1].
The v6.3/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2023-01-27 17:03 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-27 15:05 [PATCH v2 1/2] dt-bindings: arm: amlogic: add support for Radxa Zero2 Christian Hewitt
2023-01-27 15:05 ` Christian Hewitt
2023-01-27 15:05 ` Christian Hewitt
2023-01-27 15:05 ` [PATCH v2 2/2] arm64: dts: meson: " Christian Hewitt
2023-01-27 15:05 ` Christian Hewitt
2023-01-27 15:05 ` Christian Hewitt
2023-01-27 16:25 ` Neil Armstrong
2023-01-27 16:25 ` Neil Armstrong
2023-01-27 16:25 ` Neil Armstrong
2023-01-27 17:02 ` [PATCH v2 1/2] dt-bindings: arm: amlogic: " Neil Armstrong
2023-01-27 17:02 ` Neil Armstrong
2023-01-27 17:02 ` Neil Armstrong
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.