* [PATCH 0/3] arm64: dts: meson: g12a: add i2c
@ 2019-05-14 10:12 ` Jerome Brunet
0 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, devicetree, linux-amlogic, linux-kernel
Add the i2c controllers and pinctrl definitions to the g12a DT then
the busses present on the u200 and sei510.
Notice the use of the pinconf DT property 'drive-strength-microamp'.
Support for this property is not yet merged in meson pinctrl driver but
the DT part as been acked by the DT maintainer [0] so it should be safe
to use.
[0]: https://lkml.kernel.org/r/20190513152451.GA25690@bogus
Guillaume La Roque (1):
arm64: dts: meson: g12a: add i2c nodes
Jerome Brunet (2):
arm64: dts: meson: u200: enable i2c busses
arm64: dts: meson: sei510: enable i2c3
.../boot/dts/amlogic/meson-g12a-sei510.dts | 6 +
.../boot/dts/amlogic/meson-g12a-u200.dts | 21 ++
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 268 ++++++++++++++++++
3 files changed, 295 insertions(+)
--
2.20.1
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 0/3] arm64: dts: meson: g12a: add i2c
@ 2019-05-14 10:12 ` Jerome Brunet
0 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman; +Cc: devicetree, linux-amlogic, linux-kernel, Jerome Brunet
Add the i2c controllers and pinctrl definitions to the g12a DT then
the busses present on the u200 and sei510.
Notice the use of the pinconf DT property 'drive-strength-microamp'.
Support for this property is not yet merged in meson pinctrl driver but
the DT part as been acked by the DT maintainer [0] so it should be safe
to use.
[0]: https://lkml.kernel.org/r/20190513152451.GA25690@bogus
Guillaume La Roque (1):
arm64: dts: meson: g12a: add i2c nodes
Jerome Brunet (2):
arm64: dts: meson: u200: enable i2c busses
arm64: dts: meson: sei510: enable i2c3
.../boot/dts/amlogic/meson-g12a-sei510.dts | 6 +
.../boot/dts/amlogic/meson-g12a-u200.dts | 21 ++
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 268 ++++++++++++++++++
3 files changed, 295 insertions(+)
--
2.20.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 1/3] arm64: dts: meson: g12a: add i2c nodes
2019-05-14 10:12 ` Jerome Brunet
@ 2019-05-14 10:12 ` Jerome Brunet
-1 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman
Cc: Guillaume La Roque, devicetree, linux-amlogic, linux-kernel,
Jerome Brunet
From: Guillaume La Roque <glaroque@baylibre.com>
Add pinctrl and nodes for i2c support on amlogic g12a
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 268 ++++++++++++++++++++
1 file changed, 268 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index ca01064a771a..e6c0c19b3223 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -244,6 +244,188 @@
};
};
+
+ i2c0_sda_c_pins: i2c0-sda-c {
+ mux {
+ groups = "i2c0_sda_c";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+
+ };
+ };
+
+ i2c0_sck_c_pins: i2c0-sck-c {
+ mux {
+ groups = "i2c0_sck_c";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z0_pins: i2c0-sda-z0 {
+ mux {
+ groups = "i2c0_sda_z0";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sck_z1_pins: i2c0-sck-z1 {
+ mux {
+ groups = "i2c0_sck_z1";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z7_pins: i2c0-sda-z7 {
+ mux {
+ groups = "i2c0_sda_z7";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z8_pins: i2c0-sda-z8 {
+ mux {
+ groups = "i2c0_sda_z8";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_x_pins: i2c1-sda-x {
+ mux {
+ groups = "i2c1_sda_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_x_pins: i2c1-sck-x {
+ mux {
+ groups = "i2c1_sck_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_h2_pins: i2c1-sda-h2 {
+ mux {
+ groups = "i2c1_sda_h2";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_h3_pins: i2c1-sck-h3 {
+ mux {
+ groups = "i2c1_sck_h3";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_h6_pins: i2c1-sda-h6 {
+ mux {
+ groups = "i2c1_sda_h6";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_h7_pins: i2c1-sck-h7 {
+ mux {
+ groups = "i2c1_sck_h7";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sda_x_pins: i2c2-sda-x {
+ mux {
+ groups = "i2c2_sda_x";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sck_x_pins: i2c2-sck-x {
+ mux {
+ groups = "i2c2_sck_x";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sda_z_pins: i2c2-sda-z {
+ mux {
+ groups = "i2c2_sda_z";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sck_z_pins: i2c2-sck-z {
+ mux {
+ groups = "i2c2_sck_z";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sda_h_pins: i2c3-sda-h {
+ mux {
+ groups = "i2c3_sda_h";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sck_h_pins: i2c3-sck-h {
+ mux {
+ groups = "i2c3_sck_h";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sda_a_pins: i2c3-sda-a {
+ mux {
+ groups = "i2c3_sda_a";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sck_a_pins: i2c3-sck-a {
+ mux {
+ groups = "i2c3_sck_a";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
pwm_a_pins: pwm-a {
mux {
groups = "pwm_a";
@@ -589,6 +771,42 @@
gpio-ranges = <&ao_pinctrl 0 0 15>;
};
+ i2c_ao_sck_pins: i2c_ao_sck_pins {
+ mux {
+ groups = "i2c_ao_sck";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sda_pins: i2c_ao_sda {
+ mux {
+ groups = "i2c_ao_sda";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sck_e_pins: i2c_ao_sck_e {
+ mux {
+ groups = "i2c_ao_sck_e";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sda_e_pins: i2c_ao_sda_e {
+ mux {
+ groups = "i2c_ao_sda_e";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
uart_ao_a_pins: uart-a-ao {
mux {
groups = "uart_ao_a_tx",
@@ -723,6 +941,16 @@
status = "disabled";
};
+ i2c_AO: i2c@5000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x05000 0x0 0x20>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
pwm_AO_ab: pwm@7000 {
compatible = "amlogic,meson-g12a-ao-pwm-ab";
reg = <0x0 0x7000 0x0 0x20>;
@@ -826,6 +1054,46 @@
status = "disabled";
};
+ i2c3: i2c@1c000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1c000 0x0 0x20>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c2: i2c@1d000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1d000 0x0 0x20>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c1: i2c@1e000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1e000 0x0 0x20>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c0: i2c@1f000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1f000 0x0 0x20>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
clk_msr: clock-measure@18000 {
compatible = "amlogic,meson-g12a-clk-measure";
reg = <0x0 0x18000 0x0 0x10>;
--
2.20.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 1/3] arm64: dts: meson: g12a: add i2c nodes
@ 2019-05-14 10:12 ` Jerome Brunet
0 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman
Cc: devicetree, Jerome Brunet, Guillaume La Roque, linux-kernel,
linux-amlogic
From: Guillaume La Roque <glaroque@baylibre.com>
Add pinctrl and nodes for i2c support on amlogic g12a
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 268 ++++++++++++++++++++
1 file changed, 268 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index ca01064a771a..e6c0c19b3223 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -244,6 +244,188 @@
};
};
+
+ i2c0_sda_c_pins: i2c0-sda-c {
+ mux {
+ groups = "i2c0_sda_c";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+
+ };
+ };
+
+ i2c0_sck_c_pins: i2c0-sck-c {
+ mux {
+ groups = "i2c0_sck_c";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z0_pins: i2c0-sda-z0 {
+ mux {
+ groups = "i2c0_sda_z0";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sck_z1_pins: i2c0-sck-z1 {
+ mux {
+ groups = "i2c0_sck_z1";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z7_pins: i2c0-sda-z7 {
+ mux {
+ groups = "i2c0_sda_z7";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z8_pins: i2c0-sda-z8 {
+ mux {
+ groups = "i2c0_sda_z8";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_x_pins: i2c1-sda-x {
+ mux {
+ groups = "i2c1_sda_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_x_pins: i2c1-sck-x {
+ mux {
+ groups = "i2c1_sck_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_h2_pins: i2c1-sda-h2 {
+ mux {
+ groups = "i2c1_sda_h2";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_h3_pins: i2c1-sck-h3 {
+ mux {
+ groups = "i2c1_sck_h3";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_h6_pins: i2c1-sda-h6 {
+ mux {
+ groups = "i2c1_sda_h6";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_h7_pins: i2c1-sck-h7 {
+ mux {
+ groups = "i2c1_sck_h7";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sda_x_pins: i2c2-sda-x {
+ mux {
+ groups = "i2c2_sda_x";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sck_x_pins: i2c2-sck-x {
+ mux {
+ groups = "i2c2_sck_x";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sda_z_pins: i2c2-sda-z {
+ mux {
+ groups = "i2c2_sda_z";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sck_z_pins: i2c2-sck-z {
+ mux {
+ groups = "i2c2_sck_z";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sda_h_pins: i2c3-sda-h {
+ mux {
+ groups = "i2c3_sda_h";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sck_h_pins: i2c3-sck-h {
+ mux {
+ groups = "i2c3_sck_h";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sda_a_pins: i2c3-sda-a {
+ mux {
+ groups = "i2c3_sda_a";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sck_a_pins: i2c3-sck-a {
+ mux {
+ groups = "i2c3_sck_a";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
pwm_a_pins: pwm-a {
mux {
groups = "pwm_a";
@@ -589,6 +771,42 @@
gpio-ranges = <&ao_pinctrl 0 0 15>;
};
+ i2c_ao_sck_pins: i2c_ao_sck_pins {
+ mux {
+ groups = "i2c_ao_sck";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sda_pins: i2c_ao_sda {
+ mux {
+ groups = "i2c_ao_sda";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sck_e_pins: i2c_ao_sck_e {
+ mux {
+ groups = "i2c_ao_sck_e";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sda_e_pins: i2c_ao_sda_e {
+ mux {
+ groups = "i2c_ao_sda_e";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
uart_ao_a_pins: uart-a-ao {
mux {
groups = "uart_ao_a_tx",
@@ -723,6 +941,16 @@
status = "disabled";
};
+ i2c_AO: i2c@5000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x05000 0x0 0x20>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
pwm_AO_ab: pwm@7000 {
compatible = "amlogic,meson-g12a-ao-pwm-ab";
reg = <0x0 0x7000 0x0 0x20>;
@@ -826,6 +1054,46 @@
status = "disabled";
};
+ i2c3: i2c@1c000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1c000 0x0 0x20>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c2: i2c@1d000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1d000 0x0 0x20>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c1: i2c@1e000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1e000 0x0 0x20>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c0: i2c@1f000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1f000 0x0 0x20>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
clk_msr: clock-measure@18000 {
compatible = "amlogic,meson-g12a-clk-measure";
reg = <0x0 0x18000 0x0 0x10>;
--
2.20.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 2/3] arm64: dts: meson: u200: enable i2c busses
2019-05-14 10:12 ` Jerome Brunet
@ 2019-05-14 10:12 ` Jerome Brunet
-1 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, devicetree, linux-amlogic, linux-kernel
Add the 3 i2c busses present on the u200 reference design.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
.../boot/dts/amlogic/meson-g12a-u200.dts | 21 +++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
index 972926121beb..e02534ab7673 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -169,6 +169,27 @@
pinctrl-names = "default";
};
+/* i2c Touch */
+&i2c0 {
+ status = "okay";
+ pinctrl-0 = <&i2c0_sda_z0_pins>, <&i2c0_sck_z1_pins>;
+ pinctrl-names = "default";
+};
+
+/* i2c CM */
+&i2c2 {
+ status = "okay";
+ pinctrl-0 = <&i2c2_sda_z_pins>, <&i2c2_sck_z_pins>;
+ pinctrl-names = "default";
+};
+
+/* i2c Audio */
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
--
2.20.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 2/3] arm64: dts: meson: u200: enable i2c busses
@ 2019-05-14 10:12 ` Jerome Brunet
0 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman; +Cc: devicetree, linux-amlogic, linux-kernel, Jerome Brunet
Add the 3 i2c busses present on the u200 reference design.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
.../boot/dts/amlogic/meson-g12a-u200.dts | 21 +++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
index 972926121beb..e02534ab7673 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -169,6 +169,27 @@
pinctrl-names = "default";
};
+/* i2c Touch */
+&i2c0 {
+ status = "okay";
+ pinctrl-0 = <&i2c0_sda_z0_pins>, <&i2c0_sck_z1_pins>;
+ pinctrl-names = "default";
+};
+
+/* i2c CM */
+&i2c2 {
+ status = "okay";
+ pinctrl-0 = <&i2c2_sda_z_pins>, <&i2c2_sck_z_pins>;
+ pinctrl-names = "default";
+};
+
+/* i2c Audio */
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
--
2.20.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 3/3] arm64: dts: meson: sei510: enable i2c3
2019-05-14 10:12 ` Jerome Brunet
@ 2019-05-14 10:12 ` Jerome Brunet
-1 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, devicetree, linux-amlogic, linux-kernel
Add the i2c bus used for RGB led controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index bb45e3577ff5..f420935b76db 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -161,6 +161,12 @@
};
};
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+};
+
&saradc {
status = "okay";
vref-supply = <&vddio_ao1v8>;
--
2.20.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 3/3] arm64: dts: meson: sei510: enable i2c3
@ 2019-05-14 10:12 ` Jerome Brunet
0 siblings, 0 replies; 11+ messages in thread
From: Jerome Brunet @ 2019-05-14 10:12 UTC (permalink / raw)
To: Kevin Hilman; +Cc: devicetree, linux-amlogic, linux-kernel, Jerome Brunet
Add the i2c bus used for RGB led controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index bb45e3577ff5..f420935b76db 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -161,6 +161,12 @@
};
};
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+};
+
&saradc {
status = "okay";
vref-supply = <&vddio_ao1v8>;
--
2.20.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH 0/3] arm64: dts: meson: g12a: add i2c
2019-05-14 10:12 ` Jerome Brunet
(?)
@ 2019-05-20 21:14 ` Kevin Hilman
-1 siblings, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2019-05-20 21:14 UTC (permalink / raw)
To: Jerome Brunet; +Cc: Jerome Brunet, devicetree, linux-amlogic, linux-kernel
Jerome Brunet <jbrunet@baylibre.com> writes:
> Add the i2c controllers and pinctrl definitions to the g12a DT then
> the busses present on the u200 and sei510.
>
> Notice the use of the pinconf DT property 'drive-strength-microamp'.
> Support for this property is not yet merged in meson pinctrl driver but
> the DT part as been acked by the DT maintainer [0] so it should be safe
> to use.
Queued for v5.3,
Thanks,
Kevin
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 0/3] arm64: dts: meson: g12a: add i2c
@ 2019-05-20 21:14 ` Kevin Hilman
0 siblings, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2019-05-20 21:14 UTC (permalink / raw)
Cc: Jerome Brunet, devicetree, linux-amlogic, linux-kernel
Jerome Brunet <jbrunet@baylibre.com> writes:
> Add the i2c controllers and pinctrl definitions to the g12a DT then
> the busses present on the u200 and sei510.
>
> Notice the use of the pinconf DT property 'drive-strength-microamp'.
> Support for this property is not yet merged in meson pinctrl driver but
> the DT part as been acked by the DT maintainer [0] so it should be safe
> to use.
Queued for v5.3,
Thanks,
Kevin
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 0/3] arm64: dts: meson: g12a: add i2c
@ 2019-05-20 21:14 ` Kevin Hilman
0 siblings, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2019-05-20 21:14 UTC (permalink / raw)
To: Jerome Brunet; +Cc: devicetree, linux-amlogic, linux-kernel, Jerome Brunet
Jerome Brunet <jbrunet@baylibre.com> writes:
> Add the i2c controllers and pinctrl definitions to the g12a DT then
> the busses present on the u200 and sei510.
>
> Notice the use of the pinconf DT property 'drive-strength-microamp'.
> Support for this property is not yet merged in meson pinctrl driver but
> the DT part as been acked by the DT maintainer [0] so it should be safe
> to use.
Queued for v5.3,
Thanks,
Kevin
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2019-05-20 21:14 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-14 10:12 [PATCH 0/3] arm64: dts: meson: g12a: add i2c Jerome Brunet
2019-05-14 10:12 ` Jerome Brunet
2019-05-14 10:12 ` [PATCH 1/3] arm64: dts: meson: g12a: add i2c nodes Jerome Brunet
2019-05-14 10:12 ` Jerome Brunet
2019-05-14 10:12 ` [PATCH 2/3] arm64: dts: meson: u200: enable i2c busses Jerome Brunet
2019-05-14 10:12 ` Jerome Brunet
2019-05-14 10:12 ` [PATCH 3/3] arm64: dts: meson: sei510: enable i2c3 Jerome Brunet
2019-05-14 10:12 ` Jerome Brunet
2019-05-20 21:14 ` [PATCH 0/3] arm64: dts: meson: g12a: add i2c Kevin Hilman
2019-05-20 21:14 ` Kevin Hilman
2019-05-20 21:14 ` Kevin Hilman
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.