[PATCH 0/4] thermal: rcar: use thermal-zone on DT

[PATCH 0/4] thermal: rcar: use thermal-zone on DT

[Kuninori Morimoto]

Hi Zhang, Simon

These patches enables thermal-zone on R-Car thermal driver

Kuninori Morimoto (4):
      thermal: rcar: enable to use thermal-zone on DT
      ARM: shmobile: r8a7790: enable to use thermal-zone
      ARM: shmobile: r8a7791: enable to use thermal-zone
      ARM: shmobile: r8a7793: enable to use thermal-zone

 Documentation/devicetree/bindings/thermal/rcar-thermal.txt | 37 +++++++++++++++++++++++++++++++++++--
 arch/arm/boot/dts/r8a7790.dtsi                             | 26 ++++++++++++++++++++++++--
 arch/arm/boot/dts/r8a7791.dtsi                             | 26 ++++++++++++++++++++++++--
 arch/arm/boot/dts/r8a7793.dtsi                             | 26 ++++++++++++++++++++++++--
 drivers/thermal/rcar_thermal.c                             | 45 ++++++++++++++++++++++++++++++++++++++++-----
 5 files changed, 147 insertions(+), 13 deletions(-)

[PATCH 0/4] thermal: rcar: use thermal-zone on DT

[Kuninori Morimoto]

Hi Zhang, Simon

These patches enables thermal-zone on R-Car thermal driver

Kuninori Morimoto (4):
      thermal: rcar: enable to use thermal-zone on DT
      ARM: shmobile: r8a7790: enable to use thermal-zone
      ARM: shmobile: r8a7791: enable to use thermal-zone
      ARM: shmobile: r8a7793: enable to use thermal-zone

 Documentation/devicetree/bindings/thermal/rcar-thermal.txt | 37 +++++++++++++++++++++++++++++++++++--
 arch/arm/boot/dts/r8a7790.dtsi                             | 26 ++++++++++++++++++++++++--
 arch/arm/boot/dts/r8a7791.dtsi                             | 26 ++++++++++++++++++++++++--
 arch/arm/boot/dts/r8a7793.dtsi                             | 26 ++++++++++++++++++++++++--
 drivers/thermal/rcar_thermal.c                             | 45 ++++++++++++++++++++++++++++++++++++++++-----
 5 files changed, 147 insertions(+), 13 deletions(-)

[PATCH 1/4] thermal: rcar: enable to use thermal-zone on DT

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on DT if it was calles as
"renesas,rcar-thermal-gen2".
Previous style (= non thermal-zone) is still supported by
"renesas,rcar-thermal" to keep compatibility for "git bisect".

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 .../devicetree/bindings/thermal/rcar-thermal.txt   | 37 +++++++++++++++++-
 drivers/thermal/rcar_thermal.c                     | 45 +++++++++++++++++++---
 2 files changed, 75 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
index 332e625..e5ee3f1 100644
--- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
@@ -1,8 +1,9 @@
 * Renesas R-Car Thermal
 
 Required properties:
-- compatible		: "renesas,thermal-<soctype>", "renesas,rcar-thermal"
-			  as fallback.
+- compatible		: "renesas,thermal-<soctype>",
+			   "renesas,rcar-gen2-thermal" (with thermal-zone) or
+			   "renesas,rcar-thermal" (without thermal-zone) as fallback.
 			  Examples with soctypes are:
 			    - "renesas,thermal-r8a73a4" (R-Mobile APE6)
 			    - "renesas,thermal-r8a7779" (R-Car H1)
@@ -36,3 +37,35 @@ thermal@e61f0000 {
 		0xe61f0300 0x38>;
 	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 };
+
+Example (with thermal-zone):
+
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		polling-delay-passive	= <1000>;
+		polling-delay		= <5000>;
+
+		thermal-sensors = <&thermal>;
+
+		trips {
+			cpu-crit {
+				temperature	= <115000>;
+				hysteresis	= <0>;
+				type		= "critical";
+			};
+		};
+		cooling-maps {
+		};
+	};
+};
+
+thermal: thermal@e61f0000 {
+	compatible =	"renesas,thermal-r8a7790",
+			"renesas,rcar-gen2-thermal",
+			"renesas,rcar-thermal";
+	reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
+	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
+	power-domains = <&cpg_clocks>;
+	#thermal-sensor-cells = <0>;
+};
diff --git a/drivers/thermal/rcar_thermal.c b/drivers/thermal/rcar_thermal.c
index a18a732..27764ae 100644
--- a/drivers/thermal/rcar_thermal.c
+++ b/drivers/thermal/rcar_thermal.c
@@ -23,6 +23,7 @@
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/reboot.h>
@@ -75,8 +76,10 @@ struct rcar_thermal_priv {
 #define rcar_has_irq_support(priv)	((priv)->common->base)
 #define rcar_id_to_shift(priv)		((priv)->id * 8)
 
+#define USE_OF_THERMAL	1
 static const struct of_device_id rcar_thermal_dt_ids[] = {
 	{ .compatible = "renesas,rcar-thermal", },
+	{ .compatible = "renesas,rcar-gen2-thermal", .data = (void *)USE_OF_THERMAL },
 	{},
 };
 MODULE_DEVICE_TABLE(of, rcar_thermal_dt_ids);
@@ -200,9 +203,9 @@ err_out_unlock:
 	return ret;
 }
 
-static int rcar_thermal_get_temp(struct thermal_zone_device *zone, int *temp)
+static int rcar_thermal_get_current_temp(struct rcar_thermal_priv *priv,
+					 int *temp)
 {
-	struct rcar_thermal_priv *priv = rcar_zone_to_priv(zone);
 	int tmp;
 	int ret;
 
@@ -226,6 +229,20 @@ static int rcar_thermal_get_temp(struct thermal_zone_device *zone, int *temp)
 	return 0;
 }
 
+static int rcar_thermal_of_get_temp(void *data, int *temp)
+{
+	struct rcar_thermal_priv *priv = data;
+
+	return rcar_thermal_get_current_temp(priv, temp);
+}
+
+static int rcar_thermal_get_temp(struct thermal_zone_device *zone, int *temp)
+{
+	struct rcar_thermal_priv *priv = rcar_zone_to_priv(zone);
+
+	return rcar_thermal_get_current_temp(priv, temp);
+}
+
 static int rcar_thermal_get_trip_type(struct thermal_zone_device *zone,
 				      int trip, enum thermal_trip_type *type)
 {
@@ -282,6 +299,10 @@ static int rcar_thermal_notify(struct thermal_zone_device *zone,
 	return 0;
 }
 
+static const struct thermal_zone_of_device_ops rcar_thermal_zone_of_ops = {
+	.get_temp	= rcar_thermal_of_get_temp,
+};
+
 static struct thermal_zone_device_ops rcar_thermal_zone_ops = {
 	.get_temp	= rcar_thermal_get_temp,
 	.get_trip_type	= rcar_thermal_get_trip_type,
@@ -318,14 +339,20 @@ static void rcar_thermal_work(struct work_struct *work)
 
 	priv = container_of(work, struct rcar_thermal_priv, work.work);
 
-	rcar_thermal_get_temp(priv->zone, &cctemp);
+	ret = rcar_thermal_get_current_temp(priv, &cctemp);
+	if (ret < 0)
+		return;
+
 	ret = rcar_thermal_update_temp(priv);
 	if (ret < 0)
 		return;
 
 	rcar_thermal_irq_enable(priv);
 
-	rcar_thermal_get_temp(priv->zone, &nctemp);
+	ret = rcar_thermal_get_current_temp(priv, &nctemp);
+	if (ret < 0)
+		return;
+
 	if (nctemp != cctemp)
 		thermal_zone_device_update(priv->zone,
 					   THERMAL_DEVICE_EVENT_NONE);
@@ -404,6 +431,8 @@ static int rcar_thermal_probe(struct platform_device *pdev)
 	struct rcar_thermal_priv *priv;
 	struct device *dev = &pdev->dev;
 	struct resource *res, *irq;
+	const struct of_device_id *of_id = of_match_device(rcar_thermal_dt_ids, dev);
+	unsigned long of_data = (unsigned long)of_id->data;
 	int mres = 0;
 	int i;
 	int ret = -ENODEV;
@@ -464,7 +493,13 @@ static int rcar_thermal_probe(struct platform_device *pdev)
 		if (ret < 0)
 			goto error_unregister;
 
-		priv->zone = thermal_zone_device_register("rcar_thermal",
+		if (of_data == USE_OF_THERMAL)
+			priv->zone = thermal_zone_of_sensor_register(
+						dev, i, priv,
+						&rcar_thermal_zone_of_ops);
+		else
+			priv->zone = thermal_zone_device_register(
+						"rcar_thermal",
 						1, 0, priv,
 						&rcar_thermal_zone_ops, NULL, 0,
 						idle);
-- 
1.9.1

[PATCH 1/4] thermal: rcar: enable to use thermal-zone on DT

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on DT if it was calles as
"renesas,rcar-thermal-gen2".
Previous style (= non thermal-zone) is still supported by
"renesas,rcar-thermal" to keep compatibility for "git bisect".

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 .../devicetree/bindings/thermal/rcar-thermal.txt   | 37 +++++++++++++++++-
 drivers/thermal/rcar_thermal.c                     | 45 +++++++++++++++++++---
 2 files changed, 75 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
index 332e625..e5ee3f1 100644
--- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
@@ -1,8 +1,9 @@
 * Renesas R-Car Thermal
 
 Required properties:
-- compatible		: "renesas,thermal-<soctype>", "renesas,rcar-thermal"
-			  as fallback.
+- compatible		: "renesas,thermal-<soctype>",
+			   "renesas,rcar-gen2-thermal" (with thermal-zone) or
+			   "renesas,rcar-thermal" (without thermal-zone) as fallback.
 			  Examples with soctypes are:
 			    - "renesas,thermal-r8a73a4" (R-Mobile APE6)
 			    - "renesas,thermal-r8a7779" (R-Car H1)
@@ -36,3 +37,35 @@ thermal@e61f0000 {
 		0xe61f0300 0x38>;
 	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 };
+
+Example (with thermal-zone):
+
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		polling-delay-passive	= <1000>;
+		polling-delay		= <5000>;
+
+		thermal-sensors = <&thermal>;
+
+		trips {
+			cpu-crit {
+				temperature	= <115000>;
+				hysteresis	= <0>;
+				type		= "critical";
+			};
+		};
+		cooling-maps {
+		};
+	};
+};
+
+thermal: thermal@e61f0000 {
+	compatible =	"renesas,thermal-r8a7790",
+			"renesas,rcar-gen2-thermal",
+			"renesas,rcar-thermal";
+	reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
+	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
+	power-domains = <&cpg_clocks>;
+	#thermal-sensor-cells = <0>;
+};
diff --git a/drivers/thermal/rcar_thermal.c b/drivers/thermal/rcar_thermal.c
index a18a732..27764ae 100644
--- a/drivers/thermal/rcar_thermal.c
+++ b/drivers/thermal/rcar_thermal.c
@@ -23,6 +23,7 @@
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/reboot.h>
@@ -75,8 +76,10 @@ struct rcar_thermal_priv {
 #define rcar_has_irq_support(priv)	((priv)->common->base)
 #define rcar_id_to_shift(priv)		((priv)->id * 8)
 
+#define USE_OF_THERMAL	1
 static const struct of_device_id rcar_thermal_dt_ids[] = {
 	{ .compatible = "renesas,rcar-thermal", },
+	{ .compatible = "renesas,rcar-gen2-thermal", .data = (void *)USE_OF_THERMAL },
 	{},
 };
 MODULE_DEVICE_TABLE(of, rcar_thermal_dt_ids);
@@ -200,9 +203,9 @@ err_out_unlock:
 	return ret;
 }
 
-static int rcar_thermal_get_temp(struct thermal_zone_device *zone, int *temp)
+static int rcar_thermal_get_current_temp(struct rcar_thermal_priv *priv,
+					 int *temp)
 {
-	struct rcar_thermal_priv *priv = rcar_zone_to_priv(zone);
 	int tmp;
 	int ret;
 
@@ -226,6 +229,20 @@ static int rcar_thermal_get_temp(struct thermal_zone_device *zone, int *temp)
 	return 0;
 }
 
+static int rcar_thermal_of_get_temp(void *data, int *temp)
+{
+	struct rcar_thermal_priv *priv = data;
+
+	return rcar_thermal_get_current_temp(priv, temp);
+}
+
+static int rcar_thermal_get_temp(struct thermal_zone_device *zone, int *temp)
+{
+	struct rcar_thermal_priv *priv = rcar_zone_to_priv(zone);
+
+	return rcar_thermal_get_current_temp(priv, temp);
+}
+
 static int rcar_thermal_get_trip_type(struct thermal_zone_device *zone,
 				      int trip, enum thermal_trip_type *type)
 {
@@ -282,6 +299,10 @@ static int rcar_thermal_notify(struct thermal_zone_device *zone,
 	return 0;
 }
 
+static const struct thermal_zone_of_device_ops rcar_thermal_zone_of_ops = {
+	.get_temp	= rcar_thermal_of_get_temp,
+};
+
 static struct thermal_zone_device_ops rcar_thermal_zone_ops = {
 	.get_temp	= rcar_thermal_get_temp,
 	.get_trip_type	= rcar_thermal_get_trip_type,
@@ -318,14 +339,20 @@ static void rcar_thermal_work(struct work_struct *work)
 
 	priv = container_of(work, struct rcar_thermal_priv, work.work);
 
-	rcar_thermal_get_temp(priv->zone, &cctemp);
+	ret = rcar_thermal_get_current_temp(priv, &cctemp);
+	if (ret < 0)
+		return;
+
 	ret = rcar_thermal_update_temp(priv);
 	if (ret < 0)
 		return;
 
 	rcar_thermal_irq_enable(priv);
 
-	rcar_thermal_get_temp(priv->zone, &nctemp);
+	ret = rcar_thermal_get_current_temp(priv, &nctemp);
+	if (ret < 0)
+		return;
+
 	if (nctemp != cctemp)
 		thermal_zone_device_update(priv->zone,
 					   THERMAL_DEVICE_EVENT_NONE);
@@ -404,6 +431,8 @@ static int rcar_thermal_probe(struct platform_device *pdev)
 	struct rcar_thermal_priv *priv;
 	struct device *dev = &pdev->dev;
 	struct resource *res, *irq;
+	const struct of_device_id *of_id = of_match_device(rcar_thermal_dt_ids, dev);
+	unsigned long of_data = (unsigned long)of_id->data;
 	int mres = 0;
 	int i;
 	int ret = -ENODEV;
@@ -464,7 +493,13 @@ static int rcar_thermal_probe(struct platform_device *pdev)
 		if (ret < 0)
 			goto error_unregister;
 
-		priv->zone = thermal_zone_device_register("rcar_thermal",
+		if (of_data == USE_OF_THERMAL)
+			priv->zone = thermal_zone_of_sensor_register(
+						dev, i, priv,
+						&rcar_thermal_zone_of_ops);
+		else
+			priv->zone = thermal_zone_device_register(
+						"rcar_thermal",
 						1, 0, priv,
 						&rcar_thermal_zone_ops, NULL, 0,
 						idle);
-- 
1.9.1

[PATCH 2/4] ARM: shmobile: r8a7790: enable to use thermal-zone

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on r8a7790.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)

And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.

You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/boot/dts/r8a7790.dtsi | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index bbe28df..7bf2854 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -112,6 +112,25 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive	= <0>;
+			polling-delay		= <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <115000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -202,12 +221,15 @@
 		power-domains = <&cpg_clocks>;
 	};
 
-	thermal@e61f0000 {
-		compatible = "renesas,thermal-r8a7790", "renesas,rcar-thermal";
+	thermal: thermal@e61f0000 {
+		compatible =	"renesas,thermal-r8a7790",
+				"renesas,rcar-gen2-thermal",
+				"renesas,rcar-thermal";
 		reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
 		interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
 		power-domains = <&cpg_clocks>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	timer {
-- 
1.9.1

[PATCH 2/4] ARM: shmobile: r8a7790: enable to use thermal-zone

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on r8a7790.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)

And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.

You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/boot/dts/r8a7790.dtsi | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index bbe28df..7bf2854 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -112,6 +112,25 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive	= <0>;
+			polling-delay		= <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <115000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -202,12 +221,15 @@
 		power-domains = <&cpg_clocks>;
 	};
 
-	thermal@e61f0000 {
-		compatible = "renesas,thermal-r8a7790", "renesas,rcar-thermal";
+	thermal: thermal@e61f0000 {
+		compatible =	"renesas,thermal-r8a7790",
+				"renesas,rcar-gen2-thermal",
+				"renesas,rcar-thermal";
 		reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
 		interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
 		power-domains = <&cpg_clocks>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	timer {
-- 
1.9.1

[PATCH 3/4] ARM: shmobile: r8a7791: enable to use thermal-zone

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on r8a7791.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)

And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.

You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/boot/dts/r8a7791.dtsi | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 9176e45..793abd6 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -69,6 +69,25 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive	= <0>;
+			polling-delay		= <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <115000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -185,12 +204,15 @@
 		power-domains = <&cpg_clocks>;
 	};
 
-	thermal@e61f0000 {
-		compatible = "renesas,thermal-r8a7791", "renesas,rcar-thermal";
+	thermal: thermal@e61f0000 {
+		compatible =	"renesas,thermal-r8a7791",
+				"renesas,rcar-gen2-thermal",
+				"renesas,rcar-thermal";
 		reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
 		interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks R8A7791_CLK_THERMAL>;
 		power-domains = <&cpg_clocks>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	timer {
-- 
1.9.1

[PATCH 3/4] ARM: shmobile: r8a7791: enable to use thermal-zone

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on r8a7791.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)

And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.

You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/boot/dts/r8a7791.dtsi | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 9176e45..793abd6 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -69,6 +69,25 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive	= <0>;
+			polling-delay		= <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <115000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -185,12 +204,15 @@
 		power-domains = <&cpg_clocks>;
 	};
 
-	thermal@e61f0000 {
-		compatible = "renesas,thermal-r8a7791", "renesas,rcar-thermal";
+	thermal: thermal@e61f0000 {
+		compatible =	"renesas,thermal-r8a7791",
+				"renesas,rcar-gen2-thermal",
+				"renesas,rcar-thermal";
 		reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
 		interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks R8A7791_CLK_THERMAL>;
 		power-domains = <&cpg_clocks>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	timer {
-- 
1.9.1

[PATCH 4/4] ARM: shmobile: r8a7793: enable to use thermal-zone

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on r8a7793.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)

And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.

You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/boot/dts/r8a7793.dtsi | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 82c3bc9..44d07f4 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -54,6 +54,25 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive	= <0>;
+			polling-delay		= <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <115000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -170,12 +189,15 @@
 		power-domains = <&cpg_clocks>;
 	};
 
-	thermal@e61f0000 {
-		compatible = "renesas,thermal-r8a7793", "renesas,rcar-thermal";
+	thermal: thermal@e61f0000 {
+		compatible =	"renesas,thermal-r8a7793",
+				"renesas,rcar-gen2-thermal",
+				"renesas,rcar-thermal";
 		reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
 		interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks R8A7793_CLK_THERMAL>;
 		power-domains = <&cpg_clocks>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	timer {
-- 
1.9.1

[PATCH 4/4] ARM: shmobile: r8a7793: enable to use thermal-zone

[Kuninori Morimoto]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

This patch enables to use thermal-zone on r8a7793.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)

And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.

You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/boot/dts/r8a7793.dtsi | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 82c3bc9..44d07f4 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -54,6 +54,25 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive	= <0>;
+			polling-delay		= <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <115000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
 	gic: interrupt-controller@f1001000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -170,12 +189,15 @@
 		power-domains = <&cpg_clocks>;
 	};
 
-	thermal@e61f0000 {
-		compatible = "renesas,thermal-r8a7793", "renesas,rcar-thermal";
+	thermal: thermal@e61f0000 {
+		compatible =	"renesas,thermal-r8a7793",
+				"renesas,rcar-gen2-thermal",
+				"renesas,rcar-thermal";
 		reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
 		interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks R8A7793_CLK_THERMAL>;
 		power-domains = <&cpg_clocks>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	timer {
-- 
1.9.1