* [PATCH v4 1/4] dt-bindings: net: bluetooth: Add broadcom-bluetooth
@ 2017-08-17 17:59 ` Loic Poulain
0 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Loic Poulain
Add binding document for serial bluetooth chips using
Broadcom protocol.
Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
.../devicetree/bindings/net/broadcom-bluetooth.txt | 35 ++++++++++++++++++++++
1 file changed, 35 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
new file mode 100644
index 0000000..4194ff7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
@@ -0,0 +1,35 @@
+Broadcom Bluetooth Chips
+---------------------
+
+This documents the binding structure and common properties for serial
+attached Broadcom devices.
+
+Serial attached Broadcom devices shall be a child node of the host UART
+device the slave device is attached to.
+
+Required properties:
+
+ - compatible: should contain one of the following:
+ * "brcm,bcm43438-bt"
+
+Optional properties:
+
+ - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
+ - shutdown-gpios: GPIO specifier, used to enable the BT module
+ - device-wakeup-gpios: GPIO specifier, used to wakeup the controller
+ - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor
+ - clocks: clock specifier if external clock provided to the controller
+ - clock-names: should be "extclk"
+
+
+Example:
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <921600>;
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 1/4] dt-bindings: net: bluetooth: Add broadcom-bluetooth
@ 2017-08-17 17:59 ` Loic Poulain
0 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt, f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren
Cc: devicetree, linux-bluetooth, linux-rpi-kernel, Loic Poulain
Add binding document for serial bluetooth chips using
Broadcom protocol.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
.../devicetree/bindings/net/broadcom-bluetooth.txt | 35 ++++++++++++++++++++++
1 file changed, 35 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
new file mode 100644
index 0000000..4194ff7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
@@ -0,0 +1,35 @@
+Broadcom Bluetooth Chips
+---------------------
+
+This documents the binding structure and common properties for serial
+attached Broadcom devices.
+
+Serial attached Broadcom devices shall be a child node of the host UART
+device the slave device is attached to.
+
+Required properties:
+
+ - compatible: should contain one of the following:
+ * "brcm,bcm43438-bt"
+
+Optional properties:
+
+ - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
+ - shutdown-gpios: GPIO specifier, used to enable the BT module
+ - device-wakeup-gpios: GPIO specifier, used to wakeup the controller
+ - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor
+ - clocks: clock specifier if external clock provided to the controller
+ - clock-names: should be "extclk"
+
+
+Example:
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <921600>;
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 2/4] ARM: dts: bcm283x: Use stdout-path instead of console bootarg
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-17 17:59 ` Loic Poulain
-1 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Loic Poulain
Add the serial port config to "chosen/stdout-path".
Create serial0/1 aliases referring to uart0 ant uart1 paths.
Remove unneeded earlyprintk.
Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
arch/arm/boot/dts/bcm283x.dtsi | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 431dcfc..013431e 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -20,8 +20,13 @@
#address-cells = <1>;
#size-cells = <1>;
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
chosen {
- bootargs = "earlyprintk console=ttyAMA0";
+ stdout-path = "serial0:115200n8";
};
thermal-zones {
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 2/4] ARM: dts: bcm283x: Use stdout-path instead of console bootarg
@ 2017-08-17 17:59 ` Loic Poulain
0 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt, f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren
Cc: devicetree, linux-bluetooth, linux-rpi-kernel, Loic Poulain
Add the serial port config to "chosen/stdout-path".
Create serial0/1 aliases referring to uart0 ant uart1 paths.
Remove unneeded earlyprintk.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
arch/arm/boot/dts/bcm283x.dtsi | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 431dcfc..013431e 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -20,8 +20,13 @@
#address-cells = <1>;
#size-cells = <1>;
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
chosen {
- bootargs = "earlyprintk console=ttyAMA0";
+ stdout-path = "serial0:115200n8";
};
thermal-zones {
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-17 17:59 ` Loic Poulain
-1 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Loic Poulain
Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on userspace helpers (hciattach).
Overwrite chosen/stdout-path to use 8250 aux uart as console.
Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index 20725ca..e4488cb 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -8,6 +8,11 @@
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
model = "Raspberry Pi 3 Model B";
+ chosen {
+ /* 8250 auxiliar UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
memory {
reg = <0 0x40000000>;
};
@@ -24,6 +29,11 @@
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ };
};
/* uart1 is mapped to the pin header */
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
@ 2017-08-17 17:59 ` Loic Poulain
0 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt, f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren
Cc: devicetree, linux-bluetooth, linux-rpi-kernel, Loic Poulain
Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on userspace helpers (hciattach).
Overwrite chosen/stdout-path to use 8250 aux uart as console.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index 20725ca..e4488cb 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -8,6 +8,11 @@
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
model = "Raspberry Pi 3 Model B";
+ chosen {
+ /* 8250 auxiliar UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
memory {
reg = <0 0x40000000>;
};
@@ -24,6 +29,11 @@
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ };
};
/* uart1 is mapped to the pin header */
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-17 17:59 ` Loic Poulain
-1 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Loic Poulain
Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.
Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
1 file changed, 83 insertions(+), 2 deletions(-)
diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c
index 1eb286a..34882f1 100644
--- a/drivers/bluetooth/hci_bcm.c
+++ b/drivers/bluetooth/hci_bcm.c
@@ -27,6 +27,8 @@
#include <linux/firmware.h>
#include <linux/module.h>
#include <linux/acpi.h>
+#include <linux/of.h>
+#include <linux/property.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/gpio/consumer.h>
@@ -34,6 +36,7 @@
#include <linux/interrupt.h>
#include <linux/dmi.h>
#include <linux/pm_runtime.h>
+#include <linux/serdev.h>
#include <net/bluetooth/bluetooth.h>
#include <net/bluetooth/hci_core.h>
@@ -46,6 +49,7 @@
#define BCM_AUTOSUSPEND_DELAY 5000 /* default autosleep delay */
+/* platform device driver resources */
struct bcm_device {
struct list_head list;
@@ -69,6 +73,12 @@ struct bcm_device {
#endif
};
+/* serdev driver resources */
+struct bcm_serdev {
+ struct hci_uart hu;
+};
+
+/* generic bcm uart resources */
struct bcm_data {
struct sk_buff *rx_skb;
struct sk_buff_head txq;
@@ -80,6 +90,14 @@ struct bcm_data {
static DEFINE_MUTEX(bcm_device_lock);
static LIST_HEAD(bcm_device_list);
+static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
+{
+ if (hu->serdev)
+ serdev_device_set_baudrate(hu->serdev, speed);
+ else
+ hci_uart_set_baudrate(hu, speed);
+}
+
static int bcm_set_baudrate(struct hci_uart *hu, unsigned int speed)
{
struct hci_dev *hdev = hu->hdev;
@@ -290,6 +308,14 @@ static int bcm_open(struct hci_uart *hu)
hu->priv = bcm;
+ /* If this is a serdev defined device, then only use
+ * serdev open primitive and skip the rest.
+ */
+ if (hu->serdev) {
+ serdev_device_open(hu->serdev);
+ goto out;
+ }
+
if (!hu->tty->dev)
goto out;
@@ -325,6 +351,12 @@ static int bcm_close(struct hci_uart *hu)
bt_dev_dbg(hu->hdev, "hu %p", hu);
+ /* If this is a serdev defined device, only use serdev
+ * close primitive and then continue as usual.
+ */
+ if (hu->serdev)
+ serdev_device_close(hu->serdev);
+
/* Protect bcm->dev against removal of the device or driver */
mutex_lock(&bcm_device_lock);
if (bcm_device_exists(bdev)) {
@@ -400,7 +432,7 @@ static int bcm_setup(struct hci_uart *hu)
speed = 0;
if (speed)
- hci_uart_set_baudrate(hu, speed);
+ host_set_baudrate(hu, speed);
/* Operational speed if any */
if (hu->oper_speed)
@@ -413,7 +445,7 @@ static int bcm_setup(struct hci_uart *hu)
if (speed) {
err = bcm_set_baudrate(hu, speed);
if (!err)
- hci_uart_set_baudrate(hu, speed);
+ host_set_baudrate(hu, speed);
}
finalize:
@@ -906,9 +938,57 @@ static int bcm_remove(struct platform_device *pdev)
},
};
+static int bcm_serdev_probe(struct serdev_device *serdev)
+{
+ struct bcm_serdev *bcmdev;
+ u32 speed;
+ int err;
+
+ bcmdev = devm_kzalloc(&serdev->dev, sizeof(*bcmdev), GFP_KERNEL);
+ if (!bcmdev)
+ return -ENOMEM;
+
+ bcmdev->hu.serdev = serdev;
+ serdev_device_set_drvdata(serdev, bcmdev);
+
+ err = device_property_read_u32(&serdev->dev, "max-speed", &speed);
+ if (!err)
+ bcmdev->hu.oper_speed = speed;
+
+ return hci_uart_register_device(&bcmdev->hu, &bcm_proto);
+}
+
+static void bcm_serdev_remove(struct serdev_device *serdev)
+{
+ struct bcm_serdev *bcmdev = serdev_device_get_drvdata(serdev);
+
+ hci_uart_unregister_device(&bcmdev->hu);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id bcm_bluetooth_of_match[] = {
+ { .compatible = "brcm,bcm43438-bt" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, bcm_bluetooth_of_match);
+#endif
+
+static struct serdev_device_driver bcm_serdev_driver = {
+ .probe = bcm_serdev_probe,
+ .remove = bcm_serdev_remove,
+ .driver = {
+ .name = "hci_uart_bcm",
+ .of_match_table = of_match_ptr(bcm_bluetooth_of_match),
+ },
+};
+
int __init bcm_init(void)
{
+ /* For now, we need to keep both platform device
+ * driver (ACPI generated) and serdev driver (DT).
+ */
platform_driver_register(&bcm_driver);
+ serdev_device_driver_register(&bcm_serdev_driver);
return hci_uart_register_proto(&bcm_proto);
}
@@ -916,6 +996,7 @@ int __init bcm_init(void)
int __exit bcm_deinit(void)
{
platform_driver_unregister(&bcm_driver);
+ serdev_device_driver_unregister(&bcm_serdev_driver);
return hci_uart_unregister_proto(&bcm_proto);
}
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
@ 2017-08-17 17:59 ` Loic Poulain
0 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 17:59 UTC (permalink / raw)
To: robh+dt, f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren
Cc: devicetree, linux-bluetooth, linux-rpi-kernel, Loic Poulain
Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.
Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
---
v2: dt-bindings as separate patch
rebase on upcoming pi3 dts changes
v3: changes in bcm serdev drivers:
name refactoring and additional comments
Add generic host_set_baudrate method
Use agnostic device_property_read
v4: changes in doc and dts:
Add additional params to broadcom bt dt-bindings
Set the max baudrate to 2000000 instead of 921600
use chosen/stdout-path instead of console=
remove useless earlyprintk
same changes in bcm283x.dtsi
drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
1 file changed, 83 insertions(+), 2 deletions(-)
diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c
index 1eb286a..34882f1 100644
--- a/drivers/bluetooth/hci_bcm.c
+++ b/drivers/bluetooth/hci_bcm.c
@@ -27,6 +27,8 @@
#include <linux/firmware.h>
#include <linux/module.h>
#include <linux/acpi.h>
+#include <linux/of.h>
+#include <linux/property.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/gpio/consumer.h>
@@ -34,6 +36,7 @@
#include <linux/interrupt.h>
#include <linux/dmi.h>
#include <linux/pm_runtime.h>
+#include <linux/serdev.h>
#include <net/bluetooth/bluetooth.h>
#include <net/bluetooth/hci_core.h>
@@ -46,6 +49,7 @@
#define BCM_AUTOSUSPEND_DELAY 5000 /* default autosleep delay */
+/* platform device driver resources */
struct bcm_device {
struct list_head list;
@@ -69,6 +73,12 @@ struct bcm_device {
#endif
};
+/* serdev driver resources */
+struct bcm_serdev {
+ struct hci_uart hu;
+};
+
+/* generic bcm uart resources */
struct bcm_data {
struct sk_buff *rx_skb;
struct sk_buff_head txq;
@@ -80,6 +90,14 @@ struct bcm_data {
static DEFINE_MUTEX(bcm_device_lock);
static LIST_HEAD(bcm_device_list);
+static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
+{
+ if (hu->serdev)
+ serdev_device_set_baudrate(hu->serdev, speed);
+ else
+ hci_uart_set_baudrate(hu, speed);
+}
+
static int bcm_set_baudrate(struct hci_uart *hu, unsigned int speed)
{
struct hci_dev *hdev = hu->hdev;
@@ -290,6 +308,14 @@ static int bcm_open(struct hci_uart *hu)
hu->priv = bcm;
+ /* If this is a serdev defined device, then only use
+ * serdev open primitive and skip the rest.
+ */
+ if (hu->serdev) {
+ serdev_device_open(hu->serdev);
+ goto out;
+ }
+
if (!hu->tty->dev)
goto out;
@@ -325,6 +351,12 @@ static int bcm_close(struct hci_uart *hu)
bt_dev_dbg(hu->hdev, "hu %p", hu);
+ /* If this is a serdev defined device, only use serdev
+ * close primitive and then continue as usual.
+ */
+ if (hu->serdev)
+ serdev_device_close(hu->serdev);
+
/* Protect bcm->dev against removal of the device or driver */
mutex_lock(&bcm_device_lock);
if (bcm_device_exists(bdev)) {
@@ -400,7 +432,7 @@ static int bcm_setup(struct hci_uart *hu)
speed = 0;
if (speed)
- hci_uart_set_baudrate(hu, speed);
+ host_set_baudrate(hu, speed);
/* Operational speed if any */
if (hu->oper_speed)
@@ -413,7 +445,7 @@ static int bcm_setup(struct hci_uart *hu)
if (speed) {
err = bcm_set_baudrate(hu, speed);
if (!err)
- hci_uart_set_baudrate(hu, speed);
+ host_set_baudrate(hu, speed);
}
finalize:
@@ -906,9 +938,57 @@ static int bcm_remove(struct platform_device *pdev)
},
};
+static int bcm_serdev_probe(struct serdev_device *serdev)
+{
+ struct bcm_serdev *bcmdev;
+ u32 speed;
+ int err;
+
+ bcmdev = devm_kzalloc(&serdev->dev, sizeof(*bcmdev), GFP_KERNEL);
+ if (!bcmdev)
+ return -ENOMEM;
+
+ bcmdev->hu.serdev = serdev;
+ serdev_device_set_drvdata(serdev, bcmdev);
+
+ err = device_property_read_u32(&serdev->dev, "max-speed", &speed);
+ if (!err)
+ bcmdev->hu.oper_speed = speed;
+
+ return hci_uart_register_device(&bcmdev->hu, &bcm_proto);
+}
+
+static void bcm_serdev_remove(struct serdev_device *serdev)
+{
+ struct bcm_serdev *bcmdev = serdev_device_get_drvdata(serdev);
+
+ hci_uart_unregister_device(&bcmdev->hu);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id bcm_bluetooth_of_match[] = {
+ { .compatible = "brcm,bcm43438-bt" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, bcm_bluetooth_of_match);
+#endif
+
+static struct serdev_device_driver bcm_serdev_driver = {
+ .probe = bcm_serdev_probe,
+ .remove = bcm_serdev_remove,
+ .driver = {
+ .name = "hci_uart_bcm",
+ .of_match_table = of_match_ptr(bcm_bluetooth_of_match),
+ },
+};
+
int __init bcm_init(void)
{
+ /* For now, we need to keep both platform device
+ * driver (ACPI generated) and serdev driver (DT).
+ */
platform_driver_register(&bcm_driver);
+ serdev_device_driver_register(&bcm_serdev_driver);
return hci_uart_register_proto(&bcm_proto);
}
@@ -916,6 +996,7 @@ int __init bcm_init(void)
int __exit bcm_deinit(void)
{
platform_driver_unregister(&bcm_driver);
+ serdev_device_driver_unregister(&bcm_serdev_driver);
return hci_uart_unregister_proto(&bcm_proto);
}
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-17 19:30 ` Marcel Holtmann
-1 siblings, 0 replies; 26+ messages in thread
From: Marcel Holtmann @ 2017-08-17 19:30 UTC (permalink / raw)
To: Loic Poulain
Cc: Rob Herring, f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, Ray Jui,
Johan Hedberg, Stefan Wahren, devicetree,
open list:BLUETOOTH DRIVERS,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Loic,
> Add basic support for Broadcom serial slave devices.
> Probe the serial device, retrieve its maximum speed and
> register a new hci uart device.
>
> Tested/compatible with bcm43438 (RPi3).
>
> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 83 insertions(+), 2 deletions(-)
you are missing the serdev dependency.
diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index 3a6ead603e49..fae5a74dc737 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -168,6 +168,7 @@ config BT_HCIUART_INTEL
config BT_HCIUART_BCM
bool "Broadcom protocol support"
depends on BT_HCIUART
+ depends on BT_HCIUART_SERDEV
select BT_HCIUART_H4
select BT_BCM
help
Regards
Marcel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
@ 2017-08-17 19:30 ` Marcel Holtmann
0 siblings, 0 replies; 26+ messages in thread
From: Marcel Holtmann @ 2017-08-17 19:30 UTC (permalink / raw)
To: Loic Poulain
Cc: Rob Herring, f.fainelli, Ray Jui, Johan Hedberg, Stefan Wahren,
devicetree, open list:BLUETOOTH DRIVERS, linux-rpi-kernel
Hi Loic,
> Add basic support for Broadcom serial slave devices.
> Probe the serial device, retrieve its maximum speed and
> register a new hci uart device.
>
> Tested/compatible with bcm43438 (RPi3).
>
> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 83 insertions(+), 2 deletions(-)
you are missing the serdev dependency.
diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index 3a6ead603e49..fae5a74dc737 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -168,6 +168,7 @@ config BT_HCIUART_INTEL
config BT_HCIUART_BCM
bool "Broadcom protocol support"
depends on BT_HCIUART
+ depends on BT_HCIUART_SERDEV
select BT_HCIUART_H4
select BT_BCM
help
Regards
Marcel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-17 19:48 ` Marcel Holtmann
-1 siblings, 0 replies; 26+ messages in thread
From: Marcel Holtmann @ 2017-08-17 19:48 UTC (permalink / raw)
To: Loic Poulain
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
Johan Hedberg, stefan.wahren-eS4NqCHxEME,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Loic,
> Add basic support for Broadcom serial slave devices.
> Probe the serial device, retrieve its maximum speed and
> register a new hci uart device.
>
> Tested/compatible with bcm43438 (RPi3).
>
> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 83 insertions(+), 2 deletions(-)
I decided to amend your patch with the required Kconfig addition and then just applied 1/4 and 4/4 to bluetooth-next tree.
For 2/4 and 3/4, I think they should go through the DT tree since they depend on other changes. I can not apply since none of these changes are in any of my parent trees.
Regards
Marcel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
@ 2017-08-17 19:48 ` Marcel Holtmann
0 siblings, 0 replies; 26+ messages in thread
From: Marcel Holtmann @ 2017-08-17 19:48 UTC (permalink / raw)
To: Loic Poulain
Cc: robh+dt, f.fainelli, rjui, Johan Hedberg, stefan.wahren,
devicetree, linux-bluetooth, linux-rpi-kernel
Hi Loic,
> Add basic support for Broadcom serial slave devices.
> Probe the serial device, retrieve its maximum speed and
> register a new hci uart device.
>
> Tested/compatible with bcm43438 (RPi3).
>
> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 83 insertions(+), 2 deletions(-)
I decided to amend your patch with the required Kconfig addition and then just applied 1/4 and 4/4 to bluetooth-next tree.
For 2/4 and 3/4, I think they should go through the DT tree since they depend on other changes. I can not apply since none of these changes are in any of my parent trees.
Regards
Marcel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
2017-08-17 19:48 ` Marcel Holtmann
@ 2017-08-17 20:12 ` Loic Poulain
-1 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 20:12 UTC (permalink / raw)
To: Marcel Holtmann
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
Johan Hedberg, stefan.wahren-eS4NqCHxEME,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Marcel,
On 17/08/2017 21:48, Marcel Holtmann wrote:
> Hi Loic,
>
>> Add basic support for Broadcom serial slave devices.
>> Probe the serial device, retrieve its maximum speed and
>> register a new hci uart device.
>>
>> Tested/compatible with bcm43438 (RPi3).
>>
>> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>> v2: dt-bindings as separate patch
>> rebase on upcoming pi3 dts changes
>> v3: changes in bcm serdev drivers:
>> name refactoring and additional comments
>> Add generic host_set_baudrate method
>> Use agnostic device_property_read
>> v4: changes in doc and dts:
>> Add additional params to broadcom bt dt-bindings
>> Set the max baudrate to 2000000 instead of 921600
>> use chosen/stdout-path instead of console=
>> remove useless earlyprintk
>> same changes in bcm283x.dtsi
>>
>> drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
>> 1 file changed, 83 insertions(+), 2 deletions(-)
> I decided to amend your patch with the required Kconfig addition and then just applied 1/4 and 4/4 to bluetooth-next tree.
>
> For 2/4 and 3/4, I think they should go through the DT tree since they depend on other changes. I can not apply since none of these changes are in any of my parent trees.
>
>
Thanks for the amend.
Indeed 2 and 3 depend on the following DT tree changes (Stefan):
[PATCH v2] ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to
arm.
[PATCH V2 0/3] ARM: bcm283x: Raspberry Pi Zero W support
Regards,
Loic
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support
@ 2017-08-17 20:12 ` Loic Poulain
0 siblings, 0 replies; 26+ messages in thread
From: Loic Poulain @ 2017-08-17 20:12 UTC (permalink / raw)
To: Marcel Holtmann
Cc: robh+dt, f.fainelli, rjui, Johan Hedberg, stefan.wahren,
devicetree, linux-bluetooth, linux-rpi-kernel
Hi Marcel,
On 17/08/2017 21:48, Marcel Holtmann wrote:
> Hi Loic,
>
>> Add basic support for Broadcom serial slave devices.
>> Probe the serial device, retrieve its maximum speed and
>> register a new hci uart device.
>>
>> Tested/compatible with bcm43438 (RPi3).
>>
>> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
>> ---
>> v2: dt-bindings as separate patch
>> rebase on upcoming pi3 dts changes
>> v3: changes in bcm serdev drivers:
>> name refactoring and additional comments
>> Add generic host_set_baudrate method
>> Use agnostic device_property_read
>> v4: changes in doc and dts:
>> Add additional params to broadcom bt dt-bindings
>> Set the max baudrate to 2000000 instead of 921600
>> use chosen/stdout-path instead of console=
>> remove useless earlyprintk
>> same changes in bcm283x.dtsi
>>
>> drivers/bluetooth/hci_bcm.c | 85 +++++++++++++++++++++++++++++++++++++++++++--
>> 1 file changed, 83 insertions(+), 2 deletions(-)
> I decided to amend your patch with the required Kconfig addition and then just applied 1/4 and 4/4 to bluetooth-next tree.
>
> For 2/4 and 3/4, I think they should go through the DT tree since they depend on other changes. I can not apply since none of these changes are in any of my parent trees.
>
>
Thanks for the amend.
Indeed 2 and 3 depend on the following DT tree changes (Stefan):
[PATCH v2] ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to
arm.
[PATCH V2 0/3] ARM: bcm283x: Raspberry Pi Zero W support
Regards,
Loic
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 1/4] dt-bindings: net: bluetooth: Add broadcom-bluetooth
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-22 2:29 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-22 2:29 UTC (permalink / raw)
To: Loic Poulain
Cc: f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Thu, Aug 17, 2017 at 07:59:48PM +0200, Loic Poulain wrote:
> Add binding document for serial bluetooth chips using
> Broadcom protocol.
>
> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> .../devicetree/bindings/net/broadcom-bluetooth.txt | 35 ++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 1/4] dt-bindings: net: bluetooth: Add broadcom-bluetooth
@ 2017-08-22 2:29 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-22 2:29 UTC (permalink / raw)
To: Loic Poulain
Cc: f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren,
devicetree, linux-bluetooth, linux-rpi-kernel
On Thu, Aug 17, 2017 at 07:59:48PM +0200, Loic Poulain wrote:
> Add binding document for serial bluetooth chips using
> Broadcom protocol.
>
> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> .../devicetree/bindings/net/broadcom-bluetooth.txt | 35 ++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 2/4] ARM: dts: bcm283x: Use stdout-path instead of console bootarg
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-22 2:30 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-22 2:30 UTC (permalink / raw)
To: Loic Poulain
Cc: f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Thu, Aug 17, 2017 at 07:59:49PM +0200, Loic Poulain wrote:
> Add the serial port config to "chosen/stdout-path".
> Create serial0/1 aliases referring to uart0 ant uart1 paths.
> Remove unneeded earlyprintk.
>
> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> arch/arm/boot/dts/bcm283x.dtsi | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 2/4] ARM: dts: bcm283x: Use stdout-path instead of console bootarg
@ 2017-08-22 2:30 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-22 2:30 UTC (permalink / raw)
To: Loic Poulain
Cc: f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren,
devicetree, linux-bluetooth, linux-rpi-kernel
On Thu, Aug 17, 2017 at 07:59:49PM +0200, Loic Poulain wrote:
> Add the serial port config to "chosen/stdout-path".
> Create serial0/1 aliases referring to uart0 ant uart1 paths.
> Remove unneeded earlyprintk.
>
> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> arch/arm/boot/dts/bcm283x.dtsi | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-22 2:31 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-22 2:31 UTC (permalink / raw)
To: Loic Poulain
Cc: f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
marcel-kz+m5ild9QBg9hUCZPvPmw,
johan.hedberg-Re5JQEeQqe8AvxtiuMwx3w, stefan.wahren-eS4NqCHxEME,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Thu, Aug 17, 2017 at 07:59:50PM +0200, Loic Poulain wrote:
> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
> This allows to automatically insert the bcm43438 to the bluetooth
> subsystem instead of relying on userspace helpers (hciattach).
>
> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>
> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
> 1 file changed, 10 insertions(+)
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
@ 2017-08-22 2:31 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-22 2:31 UTC (permalink / raw)
To: Loic Poulain
Cc: f.fainelli, rjui, marcel, johan.hedberg, stefan.wahren,
devicetree, linux-bluetooth, linux-rpi-kernel
On Thu, Aug 17, 2017 at 07:59:50PM +0200, Loic Poulain wrote:
> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
> This allows to automatically insert the bcm43438 to the bluetooth
> subsystem instead of relying on userspace helpers (hciattach).
>
> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>
> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
> 1 file changed, 10 insertions(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
2017-08-17 17:59 ` Loic Poulain
@ 2017-08-23 14:22 ` Marcel Holtmann
-1 siblings, 0 replies; 26+ messages in thread
From: Marcel Holtmann @ 2017-08-23 14:22 UTC (permalink / raw)
To: Loic Poulain
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, rjui-dY08KVG/lbpWk0Htik3J/w,
Johan Hedberg, stefan.wahren-eS4NqCHxEME,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Loic,
> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
> This allows to automatically insert the bcm43438 to the bluetooth
> subsystem instead of relying on userspace helpers (hciattach).
>
> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>
> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
> 1 file changed, 10 insertions(+)
do you mind resending the 2 pending patches with Rob’s ack on it. And ensure that this goes with DT tree since I can currently not take it since net-next has not pulled in the pending DT patches.
Regards
Marcel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
@ 2017-08-23 14:22 ` Marcel Holtmann
0 siblings, 0 replies; 26+ messages in thread
From: Marcel Holtmann @ 2017-08-23 14:22 UTC (permalink / raw)
To: Loic Poulain
Cc: robh+dt, f.fainelli, rjui, Johan Hedberg, stefan.wahren,
devicetree, linux-bluetooth, linux-rpi-kernel
Hi Loic,
> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
> This allows to automatically insert the bcm43438 to the bluetooth
> subsystem instead of relying on userspace helpers (hciattach).
>
> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>
> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> ---
> v2: dt-bindings as separate patch
> rebase on upcoming pi3 dts changes
> v3: changes in bcm serdev drivers:
> name refactoring and additional comments
> Add generic host_set_baudrate method
> Use agnostic device_property_read
> v4: changes in doc and dts:
> Add additional params to broadcom bt dt-bindings
> Set the max baudrate to 2000000 instead of 921600
> use chosen/stdout-path instead of console=
> remove useless earlyprintk
> same changes in bcm283x.dtsi
>
> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
> 1 file changed, 10 insertions(+)
do you mind resending the 2 pending patches with Rob’s ack on it. And ensure that this goes with DT tree since I can currently not take it since net-next has not pulled in the pending DT patches.
Regards
Marcel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
2017-08-23 14:22 ` Marcel Holtmann
@ 2017-08-23 16:17 ` Eric Anholt
-1 siblings, 0 replies; 26+ messages in thread
From: Eric Anholt @ 2017-08-23 16:17 UTC (permalink / raw)
To: Marcel Holtmann, Loic Poulain
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Johan Hedberg,
rjui-dY08KVG/lbpWk0Htik3J/w,
linux-bluetooth-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
[-- Attachment #1: Type: text/plain, Size: 1553 bytes --]
Marcel Holtmann <marcel-kz+m5ild9QBg9hUCZPvPmw@public.gmane.org> writes:
> Hi Loic,
>
>> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
>> This allows to automatically insert the bcm43438 to the bluetooth
>> subsystem instead of relying on userspace helpers (hciattach).
>>
>> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>>
>> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>> v2: dt-bindings as separate patch
>> rebase on upcoming pi3 dts changes
>> v3: changes in bcm serdev drivers:
>> name refactoring and additional comments
>> Add generic host_set_baudrate method
>> Use agnostic device_property_read
>> v4: changes in doc and dts:
>> Add additional params to broadcom bt dt-bindings
>> Set the max baudrate to 2000000 instead of 921600
>> use chosen/stdout-path instead of console=
>> remove useless earlyprintk
>> same changes in bcm283x.dtsi
>>
>> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>
> do you mind resending the 2 pending patches with Rob’s ack on it. And ensure that this goes with DT tree since I can currently not take it since net-next has not pulled in the pending DT patches.
Normally we wouldn't need a resend and I'd just apply the acks when
applying the DT patches, but I don't see them in my mail.
(Also, note that since we're already at rc6 I might not be able to apply
DT patches to -next until rc1 rolls around)
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
@ 2017-08-23 16:17 ` Eric Anholt
0 siblings, 0 replies; 26+ messages in thread
From: Eric Anholt @ 2017-08-23 16:17 UTC (permalink / raw)
To: Marcel Holtmann, Loic Poulain
Cc: devicetree, Johan Hedberg, rjui, linux-bluetooth, robh+dt,
linux-rpi-kernel
[-- Attachment #1: Type: text/plain, Size: 1496 bytes --]
Marcel Holtmann <marcel@holtmann.org> writes:
> Hi Loic,
>
>> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
>> This allows to automatically insert the bcm43438 to the bluetooth
>> subsystem instead of relying on userspace helpers (hciattach).
>>
>> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>>
>> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
>> ---
>> v2: dt-bindings as separate patch
>> rebase on upcoming pi3 dts changes
>> v3: changes in bcm serdev drivers:
>> name refactoring and additional comments
>> Add generic host_set_baudrate method
>> Use agnostic device_property_read
>> v4: changes in doc and dts:
>> Add additional params to broadcom bt dt-bindings
>> Set the max baudrate to 2000000 instead of 921600
>> use chosen/stdout-path instead of console=
>> remove useless earlyprintk
>> same changes in bcm283x.dtsi
>>
>> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>
> do you mind resending the 2 pending patches with Rob’s ack on it. And ensure that this goes with DT tree since I can currently not take it since net-next has not pulled in the pending DT patches.
Normally we wouldn't need a resend and I'd just apply the acks when
applying the DT patches, but I don't see them in my mail.
(Also, note that since we're already at rc6 I might not be able to apply
DT patches to -next until rc1 rolls around)
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
2017-08-23 14:22 ` Marcel Holtmann
@ 2017-08-23 16:22 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-23 16:22 UTC (permalink / raw)
To: Marcel Holtmann
Cc: Loic Poulain, Florian Fainelli, Ray Jui, Johan Hedberg,
Stefan Wahren, devicetree-u79uwXL29TY76Z2rM5mHXA,
open list:BLUETOOTH DRIVERS,
linux-rpi-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Wed, Aug 23, 2017 at 9:22 AM, Marcel Holtmann <marcel-kz+m5ild9QBg9hUCZPvPmw@public.gmane.org> wrote:
> Hi Loic,
>
>> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
>> This allows to automatically insert the bcm43438 to the bluetooth
>> subsystem instead of relying on userspace helpers (hciattach).
>>
>> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>>
>> Signed-off-by: Loic Poulain <loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>> v2: dt-bindings as separate patch
>> rebase on upcoming pi3 dts changes
>> v3: changes in bcm serdev drivers:
>> name refactoring and additional comments
>> Add generic host_set_baudrate method
>> Use agnostic device_property_read
>> v4: changes in doc and dts:
>> Add additional params to broadcom bt dt-bindings
>> Set the max baudrate to 2000000 instead of 921600
>> use chosen/stdout-path instead of console=
>> remove useless earlyprintk
>> same changes in bcm283x.dtsi
>>
>> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>
> do you mind resending the 2 pending patches with Rob’s ack on it. And ensure that this goes with DT tree since I can currently not take it since net-next has not pulled in the pending DT patches.
They will go thru arm-soc via the sub-arch maintainer (Florian I think).
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
@ 2017-08-23 16:22 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2017-08-23 16:22 UTC (permalink / raw)
To: Marcel Holtmann
Cc: Loic Poulain, Florian Fainelli, Ray Jui, Johan Hedberg,
Stefan Wahren, devicetree, open list:BLUETOOTH DRIVERS,
linux-rpi-kernel
On Wed, Aug 23, 2017 at 9:22 AM, Marcel Holtmann <marcel@holtmann.org> wrot=
e:
> Hi Loic,
>
>> Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
>> This allows to automatically insert the bcm43438 to the bluetooth
>> subsystem instead of relying on userspace helpers (hciattach).
>>
>> Overwrite chosen/stdout-path to use 8250 aux uart as console.
>>
>> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
>> ---
>> v2: dt-bindings as separate patch
>> rebase on upcoming pi3 dts changes
>> v3: changes in bcm serdev drivers:
>> name refactoring and additional comments
>> Add generic host_set_baudrate method
>> Use agnostic device_property_read
>> v4: changes in doc and dts:
>> Add additional params to broadcom bt dt-bindings
>> Set the max baudrate to 2000000 instead of 921600
>> use chosen/stdout-path instead of console=3D
>> remove useless earlyprintk
>> same changes in bcm283x.dtsi
>>
>> arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>
> do you mind resending the 2 pending patches with Rob=E2=80=99s ack on it.=
And ensure that this goes with DT tree since I can currently not take it s=
ince net-next has not pulled in the pending DT patches.
They will go thru arm-soc via the sub-arch maintainer (Florian I think).
Rob
^ permalink raw reply [flat|nested] 26+ messages in thread
end of thread, other threads:[~2017-08-23 16:22 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-08-17 17:59 [PATCH v4 1/4] dt-bindings: net: bluetooth: Add broadcom-bluetooth Loic Poulain
2017-08-17 17:59 ` Loic Poulain
[not found] ` <1502992791-10265-1-git-send-email-loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-08-17 17:59 ` [PATCH v4 2/4] ARM: dts: bcm283x: Use stdout-path instead of console bootarg Loic Poulain
2017-08-17 17:59 ` Loic Poulain
[not found] ` <1502992791-10265-2-git-send-email-loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-08-22 2:30 ` Rob Herring
2017-08-22 2:30 ` Rob Herring
2017-08-17 17:59 ` [PATCH v4 3/4] ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave Loic Poulain
2017-08-17 17:59 ` Loic Poulain
[not found] ` <1502992791-10265-3-git-send-email-loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-08-22 2:31 ` Rob Herring
2017-08-22 2:31 ` Rob Herring
2017-08-23 14:22 ` Marcel Holtmann
2017-08-23 14:22 ` Marcel Holtmann
[not found] ` <972AD2C1-FE7C-412D-AEC6-FFED22EC4B77-kz+m5ild9QBg9hUCZPvPmw@public.gmane.org>
2017-08-23 16:17 ` Eric Anholt
2017-08-23 16:17 ` Eric Anholt
2017-08-23 16:22 ` Rob Herring
2017-08-23 16:22 ` Rob Herring
2017-08-17 17:59 ` [PATCH v4 4/4] Bluetooth: hci_bcm: Add serdev support Loic Poulain
2017-08-17 17:59 ` Loic Poulain
[not found] ` <1502992791-10265-4-git-send-email-loic.poulain-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2017-08-17 19:30 ` Marcel Holtmann
2017-08-17 19:30 ` Marcel Holtmann
2017-08-17 19:48 ` Marcel Holtmann
2017-08-17 19:48 ` Marcel Holtmann
[not found] ` <C0CDF47D-95D8-4270-A6C2-F83C00954A95-kz+m5ild9QBg9hUCZPvPmw@public.gmane.org>
2017-08-17 20:12 ` Loic Poulain
2017-08-17 20:12 ` Loic Poulain
2017-08-22 2:29 ` [PATCH v4 1/4] dt-bindings: net: bluetooth: Add broadcom-bluetooth Rob Herring
2017-08-22 2:29 ` Rob Herring
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.