All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
@ 2020-03-28 21:21 ` eichest
  0 siblings, 0 replies; 8+ messages in thread
From: eichest @ 2020-03-28 21:21 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Gregory Clement,
	Sebastian Hesselbarth, Rob Herring
  Cc: Stefan Eichenberger, linux-arm-kernel, devicetree, linux-kernel

From: Stefan Eichenberger <eichest@gmail.com>

According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
pin for the gigabit phy is MPP62 and not MPP43.

Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
---
 .../dts/marvell/armada-8040-clearfog-gt-8k.dts     | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index b90d78a5724b..d371d938b41e 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -144,7 +144,6 @@
 	 * [35-38] CP0 I2C1 and I2C0
 	 * [39] GPIO reset button
 	 * [40,41] LED0 and LED1
-	 * [43] 1512 phy reset
 	 * [47] USB VBUS EN (active low)
 	 * [48] FAN PWM
 	 * [49] SFP+ present signal
@@ -155,6 +154,7 @@
 	 * [54] NFC reset
 	 * [55] Micro SD card detect
 	 * [56-61] Micro SD
+	 * [62] 1512 phy reset
 	 */
 
 	cp0_pci0_reset_pins: pci0-reset-pins {
@@ -197,11 +197,6 @@
 		marvell,function = "gpio";
 	};
 
-	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
-		marvell,pins = "mpp43";
-		marvell,function = "gpio";
-	};
-
 	cp0_xhci_vbus_pins: xhci0-vbus-pins {
 		marvell,pins = "mpp47";
 		marvell,function = "gpio";
@@ -232,6 +227,11 @@
 			       "mpp60", "mpp61";
 		marvell,function = "sdio";
 	};
+
+	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
+		marvell,pins = "mpp62";
+		marvell,function = "gpio";
+	};
 };
 
 &cp0_pcie0 {
@@ -365,7 +365,7 @@
 		reg = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp0_copper_eth_phy_reset>;
-		reset-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_LOW>;
 		reset-assert-us = <10000>;
 		reset-deassert-us = <10000>;
 	};
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 8+ messages in thread
* [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
@ 2020-03-28 21:21 ` eichest
  0 siblings, 0 replies; 8+ messages in thread
From: eichest @ 2020-03-28 21:21 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Gregory Clement,
	Sebastian Hesselbarth, Rob Herring
  Cc: devicetree, Stefan Eichenberger, linux-kernel, linux-arm-kernel

From: Stefan Eichenberger <eichest@gmail.com>

According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
pin for the gigabit phy is MPP62 and not MPP43.

Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
---
 .../dts/marvell/armada-8040-clearfog-gt-8k.dts     | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index b90d78a5724b..d371d938b41e 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -144,7 +144,6 @@
 	 * [35-38] CP0 I2C1 and I2C0
 	 * [39] GPIO reset button
 	 * [40,41] LED0 and LED1
-	 * [43] 1512 phy reset
 	 * [47] USB VBUS EN (active low)
 	 * [48] FAN PWM
 	 * [49] SFP+ present signal
@@ -155,6 +154,7 @@
 	 * [54] NFC reset
 	 * [55] Micro SD card detect
 	 * [56-61] Micro SD
+	 * [62] 1512 phy reset
 	 */
 
 	cp0_pci0_reset_pins: pci0-reset-pins {
@@ -197,11 +197,6 @@
 		marvell,function = "gpio";
 	};
 
-	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
-		marvell,pins = "mpp43";
-		marvell,function = "gpio";
-	};
-
 	cp0_xhci_vbus_pins: xhci0-vbus-pins {
 		marvell,pins = "mpp47";
 		marvell,function = "gpio";
@@ -232,6 +227,11 @@
 			       "mpp60", "mpp61";
 		marvell,function = "sdio";
 	};
+
+	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
+		marvell,pins = "mpp62";
+		marvell,function = "gpio";
+	};
 };
 
 &cp0_pcie0 {
@@ -365,7 +365,7 @@
 		reg = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp0_copper_eth_phy_reset>;
-		reset-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_LOW>;
 		reset-assert-us = <10000>;
 		reset-deassert-us = <10000>;
 	};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
  2020-03-28 21:21 ` eichest
@ 2020-03-29  6:22   ` Baruch Siach
  -1 siblings, 0 replies; 8+ messages in thread
From: Baruch Siach @ 2020-03-29  6:22 UTC (permalink / raw)
  To: Stefan Eichenberger
  Cc: Jason Cooper, Andrew Lunn, Gregory Clement,
	Sebastian Hesselbarth, Rob Herring, devicetree,
	Stefan Eichenberger, linux-kernel, linux-arm-kernel,
	Russell King, Rabeeh Khoury

Hi Stefan,

On Sun, Mar 29 2020, eichest@gmail.com wrote:
> From: Stefan Eichenberger <eichest@gmail.com>
>
> According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> pin for the gigabit phy is MPP62 and not MPP43.

Have you tested that on real hardware?

The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
deassert delay") indicates that this is the case on his board as well.

In case there was a hardware change between board revisions, we need
another dtb for that revision.

baruch

> Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
> ---
>  .../dts/marvell/armada-8040-clearfog-gt-8k.dts     | 14 +++++++-------
>  1 file changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> index b90d78a5724b..d371d938b41e 100644
> --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> @@ -144,7 +144,6 @@
>  	 * [35-38] CP0 I2C1 and I2C0
>  	 * [39] GPIO reset button
>  	 * [40,41] LED0 and LED1
> -	 * [43] 1512 phy reset
>  	 * [47] USB VBUS EN (active low)
>  	 * [48] FAN PWM
>  	 * [49] SFP+ present signal
> @@ -155,6 +154,7 @@
>  	 * [54] NFC reset
>  	 * [55] Micro SD card detect
>  	 * [56-61] Micro SD
> +	 * [62] 1512 phy reset
>  	 */
>
>  	cp0_pci0_reset_pins: pci0-reset-pins {
> @@ -197,11 +197,6 @@
>  		marvell,function = "gpio";
>  	};
>
> -	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
> -		marvell,pins = "mpp43";
> -		marvell,function = "gpio";
> -	};
> -
>  	cp0_xhci_vbus_pins: xhci0-vbus-pins {
>  		marvell,pins = "mpp47";
>  		marvell,function = "gpio";
> @@ -232,6 +227,11 @@
>  			       "mpp60", "mpp61";
>  		marvell,function = "sdio";
>  	};
> +
> +	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
> +		marvell,pins = "mpp62";
> +		marvell,function = "gpio";
> +	};
>  };
>
>  &cp0_pcie0 {
> @@ -365,7 +365,7 @@
>  		reg = <0>;
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&cp0_copper_eth_phy_reset>;
> -		reset-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
> +		reset-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_LOW>;
>  		reset-assert-us = <10000>;
>  		reset-deassert-us = <10000>;
>  	};


--
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

^ permalink raw reply	[flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
@ 2020-03-29  6:22   ` Baruch Siach
  0 siblings, 0 replies; 8+ messages in thread
From: Baruch Siach @ 2020-03-29  6:22 UTC (permalink / raw)
  To: Stefan Eichenberger
  Cc: Andrew Lunn, Stefan Eichenberger, Jason Cooper, devicetree,
	Gregory Clement, linux-kernel, Russell King, Rob Herring,
	Rabeeh Khoury, linux-arm-kernel, Sebastian Hesselbarth

Hi Stefan,

On Sun, Mar 29 2020, eichest@gmail.com wrote:
> From: Stefan Eichenberger <eichest@gmail.com>
>
> According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> pin for the gigabit phy is MPP62 and not MPP43.

Have you tested that on real hardware?

The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
deassert delay") indicates that this is the case on his board as well.

In case there was a hardware change between board revisions, we need
another dtb for that revision.

baruch

> Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
> ---
>  .../dts/marvell/armada-8040-clearfog-gt-8k.dts     | 14 +++++++-------
>  1 file changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> index b90d78a5724b..d371d938b41e 100644
> --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
> @@ -144,7 +144,6 @@
>  	 * [35-38] CP0 I2C1 and I2C0
>  	 * [39] GPIO reset button
>  	 * [40,41] LED0 and LED1
> -	 * [43] 1512 phy reset
>  	 * [47] USB VBUS EN (active low)
>  	 * [48] FAN PWM
>  	 * [49] SFP+ present signal
> @@ -155,6 +154,7 @@
>  	 * [54] NFC reset
>  	 * [55] Micro SD card detect
>  	 * [56-61] Micro SD
> +	 * [62] 1512 phy reset
>  	 */
>
>  	cp0_pci0_reset_pins: pci0-reset-pins {
> @@ -197,11 +197,6 @@
>  		marvell,function = "gpio";
>  	};
>
> -	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
> -		marvell,pins = "mpp43";
> -		marvell,function = "gpio";
> -	};
> -
>  	cp0_xhci_vbus_pins: xhci0-vbus-pins {
>  		marvell,pins = "mpp47";
>  		marvell,function = "gpio";
> @@ -232,6 +227,11 @@
>  			       "mpp60", "mpp61";
>  		marvell,function = "sdio";
>  	};
> +
> +	cp0_copper_eth_phy_reset: copper-eth-phy-reset {
> +		marvell,pins = "mpp62";
> +		marvell,function = "gpio";
> +	};
>  };
>
>  &cp0_pcie0 {
> @@ -365,7 +365,7 @@
>  		reg = <0>;
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&cp0_copper_eth_phy_reset>;
> -		reset-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
> +		reset-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_LOW>;
>  		reset-assert-us = <10000>;
>  		reset-deassert-us = <10000>;
>  	};


--
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
  2020-03-29  6:22   ` Baruch Siach
@ 2020-03-29  8:42     ` Rabeeh Khoury
  -1 siblings, 0 replies; 8+ messages in thread
From: Rabeeh Khoury @ 2020-03-29  8:42 UTC (permalink / raw)
  To: Baruch Siach
  Cc: Stefan Eichenberger, Jason Cooper, Andrew Lunn, Gregory Clement,
	Sebastian Hesselbarth, Rob Herring, devicetree, linux-kernel,
	linux-arm-kernel, Russell King

On Sun, Mar 29, 2020 at 9:22 AM Baruch Siach <baruch@tkos.co.il> wrote:
>
> Hi Stefan,
>
> On Sun, Mar 29 2020, eichest@gmail.com wrote:
> > From: Stefan Eichenberger <eichest@gmail.com>
> >
> > According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> > pin for the gigabit phy is MPP62 and not MPP43.
>
> Have you tested that on real hardware?
>
> The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
> commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
> deassert delay") indicates that this is the case on his board as well.
>
> In case there was a hardware change between board revisions, we need
> another dtb for that revision.

It's a bug in the simplified schematics since that schematics is based
on rev 1.0 and not rev 1.1 as claimed.

In rev 1.0; the 1Gbps phy reset was connected to MPP62; but that MPP
is not functional as a GPIO when selecting MPP[56:61] as SD card.
Due to that we manually rewired ALL rev 1.0 PCBs 1Gbps phy to be
connected to MPP43 via R8038 pads.

Rev 1.1 fixes this by that by disconnecting 1Gbps phy reset from MPP62
and wiring it to MPP43.
So basically rev 1.0 and rev 1.1 are compatible software wise. We will
fix the schematics.

Rabeeh

^ permalink raw reply	[flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
@ 2020-03-29  8:42     ` Rabeeh Khoury
  0 siblings, 0 replies; 8+ messages in thread
From: Rabeeh Khoury @ 2020-03-29  8:42 UTC (permalink / raw)
  To: Baruch Siach
  Cc: Andrew Lunn, Stefan Eichenberger, Jason Cooper, devicetree,
	Gregory Clement, linux-kernel, Russell King, Rob Herring,
	linux-arm-kernel, Sebastian Hesselbarth

On Sun, Mar 29, 2020 at 9:22 AM Baruch Siach <baruch@tkos.co.il> wrote:
>
> Hi Stefan,
>
> On Sun, Mar 29 2020, eichest@gmail.com wrote:
> > From: Stefan Eichenberger <eichest@gmail.com>
> >
> > According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> > pin for the gigabit phy is MPP62 and not MPP43.
>
> Have you tested that on real hardware?
>
> The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
> commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
> deassert delay") indicates that this is the case on his board as well.
>
> In case there was a hardware change between board revisions, we need
> another dtb for that revision.

It's a bug in the simplified schematics since that schematics is based
on rev 1.0 and not rev 1.1 as claimed.

In rev 1.0; the 1Gbps phy reset was connected to MPP62; but that MPP
is not functional as a GPIO when selecting MPP[56:61] as SD card.
Due to that we manually rewired ALL rev 1.0 PCBs 1Gbps phy to be
connected to MPP43 via R8038 pads.

Rev 1.1 fixes this by that by disconnecting 1Gbps phy reset from MPP62
and wiring it to MPP43.
So basically rev 1.0 and rev 1.1 are compatible software wise. We will
fix the schematics.

Rabeeh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
  2020-03-29  8:42     ` Rabeeh Khoury
@ 2020-03-29  9:20       ` Stefan Eichenberger
  -1 siblings, 0 replies; 8+ messages in thread
From: Stefan Eichenberger @ 2020-03-29  9:20 UTC (permalink / raw)
  To: Rabeeh Khoury
  Cc: Baruch Siach, Jason Cooper, Andrew Lunn, Gregory Clement,
	Sebastian Hesselbarth, Rob Herring, devicetree, linux-kernel,
	linux-arm-kernel, Russell King

Hi Rabeeh and Baruch

On Sun, Mar 29, 2020 at 11:42:35AM +0300, Rabeeh Khoury wrote:
> On Sun, Mar 29, 2020 at 9:22 AM Baruch Siach <baruch@tkos.co.il> wrote:
> >
> > Hi Stefan,
> >
> > On Sun, Mar 29 2020, eichest@gmail.com wrote:
> > > From: Stefan Eichenberger <eichest@gmail.com>
> > >
> > > According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> > > pin for the gigabit phy is MPP62 and not MPP43.
> >
> > Have you tested that on real hardware?
> >
> > The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
> > commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
> > deassert delay") indicates that this is the case on his board as well.
> >
> > In case there was a hardware change between board revisions, we need
> > another dtb for that revision.
> 
> It's a bug in the simplified schematics since that schematics is based
> on rev 1.0 and not rev 1.1 as claimed.
> 
> In rev 1.0; the 1Gbps phy reset was connected to MPP62; but that MPP
> is not functional as a GPIO when selecting MPP[56:61] as SD card.
> Due to that we manually rewired ALL rev 1.0 PCBs 1Gbps phy to be
> connected to MPP43 via R8038 pads.
> 
> Rev 1.1 fixes this by that by disconnecting 1Gbps phy reset from MPP62
> and wiring it to MPP43.
> So basically rev 1.0 and rev 1.1 are compatible software wise. We will
> fix the schematics.

Ahh now I see, I didn't enable the phy driver when I did the test with
the default devicetree and then when I changed the devicetree I also
enabled the driver, that's my fault.

Sorry for the confusion... I can confirm that it works with MPP43.
Thanks for the clarification!

Regards,
Stefan

^ permalink raw reply	[flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin
@ 2020-03-29  9:20       ` Stefan Eichenberger
  0 siblings, 0 replies; 8+ messages in thread
From: Stefan Eichenberger @ 2020-03-29  9:20 UTC (permalink / raw)
  To: Rabeeh Khoury
  Cc: Andrew Lunn, Baruch Siach, Jason Cooper, devicetree,
	Gregory Clement, linux-kernel, Russell King, Rob Herring,
	linux-arm-kernel, Sebastian Hesselbarth

Hi Rabeeh and Baruch

On Sun, Mar 29, 2020 at 11:42:35AM +0300, Rabeeh Khoury wrote:
> On Sun, Mar 29, 2020 at 9:22 AM Baruch Siach <baruch@tkos.co.il> wrote:
> >
> > Hi Stefan,
> >
> > On Sun, Mar 29 2020, eichest@gmail.com wrote:
> > > From: Stefan Eichenberger <eichest@gmail.com>
> > >
> > > According to the ClearFog-GT-8K-rev-1_1-Simplified-Schematic the reset
> > > pin for the gigabit phy is MPP62 and not MPP43.
> >
> > Have you tested that on real hardware?
> >
> > The 1Gb PHY reset on my Clearfog GT-8K is connected to MPP43. Russell's
> > commit 46f94c7818e7 ("arm64: dts: clearfog-gt-8k: set gigabit PHY reset
> > deassert delay") indicates that this is the case on his board as well.
> >
> > In case there was a hardware change between board revisions, we need
> > another dtb for that revision.
> 
> It's a bug in the simplified schematics since that schematics is based
> on rev 1.0 and not rev 1.1 as claimed.
> 
> In rev 1.0; the 1Gbps phy reset was connected to MPP62; but that MPP
> is not functional as a GPIO when selecting MPP[56:61] as SD card.
> Due to that we manually rewired ALL rev 1.0 PCBs 1Gbps phy to be
> connected to MPP43 via R8038 pads.
> 
> Rev 1.1 fixes this by that by disconnecting 1Gbps phy reset from MPP62
> and wiring it to MPP43.
> So basically rev 1.0 and rev 1.1 are compatible software wise. We will
> fix the schematics.

Ahh now I see, I didn't enable the phy driver when I did the test with
the default devicetree and then when I changed the devicetree I also
enabled the driver, that's my fault.

Sorry for the confusion... I can confirm that it works with MPP43.
Thanks for the clarification!

Regards,
Stefan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-03-29  9:21 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-28 21:21 [PATCH] arm64: dts: clearfog-gt-8k: fix ge phy reset pin eichest
2020-03-28 21:21 ` eichest
2020-03-29  6:22 ` Baruch Siach
2020-03-29  6:22   ` Baruch Siach
2020-03-29  8:42   ` Rabeeh Khoury
2020-03-29  8:42     ` Rabeeh Khoury
2020-03-29  9:20     ` Stefan Eichenberger
2020-03-29  9:20       ` Stefan Eichenberger

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.