* [PATCH 0/2 v3] ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
@ 2015-12-14 14:32 Linus Walleij
2015-12-14 15:05 ` Andrew Lunn
0 siblings, 1 reply; 3+ messages in thread
From: Linus Walleij @ 2015-12-14 14:32 UTC (permalink / raw)
To: linux-arm-kernel
This adds a device tree for the CloudEngines PogoPlug series 4
NAS device. Inspired by out-of-tree boardfiles from ArchLinux
by Kevin Mihelich.
Cc: Moonman <moonman.ca@gmail.com>
Cc: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v2->v3:
- Drop current-speed = <115200> from the uart
ChangeLog v1->v2:
- Use <dt-bindings/input/linux-event-codes.h>
- Specify default baud rate etc differently
- Rename LEDs "pogoplugv4*"
- Skip registering i2c0 as there is nothing on it
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++
2 files changed, 179 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 30bbc3746130..2d9f475a9ceb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-openrd-client.dtb \
kirkwood-openrd-ultimate.dtb \
kirkwood-pogo_e02.dtb \
+ kirkwood-pogoplug-series-4.dtb \
kirkwood-rd88f6192.dtb \
kirkwood-rd88f6281-z0.dtb \
kirkwood-rd88f6281-a.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
new file mode 100644
index 000000000000..1db6f2c506cc
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
@@ -0,0 +1,178 @@
+/*
+ * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4
+ * inspired by the board files made by Kevin Mihelich for ArchLinux,
+ * and their DTS file.
+ *
+ * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+ model = "Cloud Engines PogoPlug Series 4";
+ compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
+ "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>;
+ };
+
+ chosen {
+ stdout-path = "uart0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_button_eject>;
+ pinctrl-names = "default";
+
+ button at 1 {
+ debounce_interval = <50>;
+ wakeup-source;
+ linux,code = <KEY_EJECTCD>;
+ label = "Eject Button";
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_green &pmx_led_red>;
+ pinctrl-names = "default";
+
+ health {
+ label = "pogoplugv4:green:health";
+ gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ fault {
+ label = "pogoplugv4:red:fault";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&pinctrl {
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp21";
+ marvell,function = "sata0";
+ };
+
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp20";
+ marvell,function = "sata1";
+ };
+
+ pmx_sdio_cd: pmx-sdio-cd {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio_wp: pmx-sdio-wp {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_eject: pmx-button-eject {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_green: pmx-led-green {
+ marvell,pins = "mpp22";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_red: pmx-led-red {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/*
+ * This PCIE controller has a USB 3.0 XHCI controller at 1,0
+ */
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
+ pinctrl-names = "default";
+ nr-ports = <1>;
+};
+
+&sdio {
+ status = "okay";
+ pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>;
+ pinctrl-names = "default";
+ cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+};
+
+&nand {
+ /* 128 MiB of NAND flash */
+ chip-delay = <40>;
+ status = "okay";
+ partitions {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x00000000 0x200000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "uImage";
+ reg = <0x00200000 0x300000>;
+ };
+
+ partition at 500000 {
+ label = "uImage2";
+ reg = <0x00500000 0x300000>;
+ };
+
+ partition at 800000 {
+ label = "failsafe";
+ reg = <0x00800000 0x800000>;
+ };
+
+ partition at 1000000 {
+ label = "root";
+ reg = <0x01000000 0x7000000>;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port at 0 {
+ phy-handle = <ðphy0>;
+ };
+};
--
2.4.3
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH 0/2 v3] ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
2015-12-14 14:32 [PATCH 0/2 v3] ARM: mvebu: kirkwood: add PogoPlug series 4 device tree Linus Walleij
@ 2015-12-14 15:05 ` Andrew Lunn
2015-12-15 16:21 ` Gregory CLEMENT
0 siblings, 1 reply; 3+ messages in thread
From: Andrew Lunn @ 2015-12-14 15:05 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Dec 14, 2015 at 03:32:55PM +0100, Linus Walleij wrote:
> This adds a device tree for the CloudEngines PogoPlug series 4
> NAS device. Inspired by out-of-tree boardfiles from ArchLinux
> by Kevin Mihelich.
>
> Cc: Moonman <moonman.ca@gmail.com>
> Cc: Kevin Mihelich <kevin@archlinuxarm.org>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Thanks
Andrew
> ---
> ChangeLog v2->v3:
> - Drop current-speed = <115200> from the uart
> ChangeLog v1->v2:
> - Use <dt-bindings/input/linux-event-codes.h>
> - Specify default baud rate etc differently
> - Rename LEDs "pogoplugv4*"
> - Skip registering i2c0 as there is nothing on it
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++
> 2 files changed, 179 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 30bbc3746130..2d9f475a9ceb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
> kirkwood-openrd-client.dtb \
> kirkwood-openrd-ultimate.dtb \
> kirkwood-pogo_e02.dtb \
> + kirkwood-pogoplug-series-4.dtb \
> kirkwood-rd88f6192.dtb \
> kirkwood-rd88f6281-z0.dtb \
> kirkwood-rd88f6281-a.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
> new file mode 100644
> index 000000000000..1db6f2c506cc
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
> @@ -0,0 +1,178 @@
> +/*
> + * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4
> + * inspired by the board files made by Kevin Mihelich for ArchLinux,
> + * and their DTS file.
> + *
> + * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org>
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6192.dtsi"
> +#include <dt-bindings/input/linux-event-codes.h>
> +
> +/ {
> + model = "Cloud Engines PogoPlug Series 4";
> + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
> + "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x08000000>;
> + };
> +
> + chosen {
> + stdout-path = "uart0:115200n8";
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_button_eject>;
> + pinctrl-names = "default";
> +
> + button at 1 {
> + debounce_interval = <50>;
> + wakeup-source;
> + linux,code = <KEY_EJECTCD>;
> + label = "Eject Button";
> + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_green &pmx_led_red>;
> + pinctrl-names = "default";
> +
> + health {
> + label = "pogoplugv4:green:health";
> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
> + default-state = "on";
> + };
> + fault {
> + label = "pogoplugv4:red:fault";
> + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&pinctrl {
> + pmx_sata0: pmx-sata0 {
> + marvell,pins = "mpp21";
> + marvell,function = "sata0";
> + };
> +
> + pmx_sata1: pmx-sata1 {
> + marvell,pins = "mpp20";
> + marvell,function = "sata1";
> + };
> +
> + pmx_sdio_cd: pmx-sdio-cd {
> + marvell,pins = "mpp27";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sdio_wp: pmx-sdio-wp {
> + marvell,pins = "mpp28";
> + marvell,function = "gpio";
> + };
> +
> + pmx_button_eject: pmx-button-eject {
> + marvell,pins = "mpp29";
> + marvell,function = "gpio";
> + };
> +
> + pmx_led_green: pmx-led-green {
> + marvell,pins = "mpp22";
> + marvell,function = "gpio";
> + };
> +
> + pmx_led_red: pmx-led-red {
> + marvell,pins = "mpp24";
> + marvell,function = "gpio";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +/*
> + * This PCIE controller has a USB 3.0 XHCI controller at 1,0
> + */
> +&pciec {
> + status = "okay";
> +};
> +
> +&pcie0 {
> + status = "okay";
> +};
> +
> +&sata {
> + status = "okay";
> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
> + pinctrl-names = "default";
> + nr-ports = <1>;
> +};
> +
> +&sdio {
> + status = "okay";
> + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>;
> + pinctrl-names = "default";
> + cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&nand {
> + /* 128 MiB of NAND flash */
> + chip-delay = <40>;
> + status = "okay";
> + partitions {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x00000000 0x200000>;
> + read-only;
> + };
> +
> + partition at 200000 {
> + label = "uImage";
> + reg = <0x00200000 0x300000>;
> + };
> +
> + partition at 500000 {
> + label = "uImage2";
> + reg = <0x00500000 0x300000>;
> + };
> +
> + partition at 800000 {
> + label = "failsafe";
> + reg = <0x00800000 0x800000>;
> + };
> +
> + partition at 1000000 {
> + label = "root";
> + reg = <0x01000000 0x7000000>;
> + };
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy at 0 {
> + reg = <0>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port at 0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> --
> 2.4.3
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH 0/2 v3] ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
2015-12-14 15:05 ` Andrew Lunn
@ 2015-12-15 16:21 ` Gregory CLEMENT
0 siblings, 0 replies; 3+ messages in thread
From: Gregory CLEMENT @ 2015-12-15 16:21 UTC (permalink / raw)
To: linux-arm-kernel
Hi Linus,
On lun., d?c. 14 2015, Andrew Lunn <andrew@lunn.ch> wrote:
> On Mon, Dec 14, 2015 at 03:32:55PM +0100, Linus Walleij wrote:
>> This adds a device tree for the CloudEngines PogoPlug series 4
>> NAS device. Inspired by out-of-tree boardfiles from ArchLinux
>> by Kevin Mihelich.
>>
>> Cc: Moonman <moonman.ca@gmail.com>
>> Cc: Kevin Mihelich <kevin@archlinuxarm.org>
>> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>
> Acked-by: Andrew Lunn <andrew@lunn.ch>
Applied on mvebu/dt
Thanks,
Gregory
>
> Thanks
> Andrew
>
>> ---
>> ChangeLog v2->v3:
>> - Drop current-speed = <115200> from the uart
>> ChangeLog v1->v2:
>> - Use <dt-bindings/input/linux-event-codes.h>
>> - Specify default baud rate etc differently
>> - Rename LEDs "pogoplugv4*"
>> - Skip registering i2c0 as there is nothing on it
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts | 178 +++++++++++++++++++++++
>> 2 files changed, 179 insertions(+)
>> create mode 100644 arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 30bbc3746130..2d9f475a9ceb 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
>> kirkwood-openrd-client.dtb \
>> kirkwood-openrd-ultimate.dtb \
>> kirkwood-pogo_e02.dtb \
>> + kirkwood-pogoplug-series-4.dtb \
>> kirkwood-rd88f6192.dtb \
>> kirkwood-rd88f6281-z0.dtb \
>> kirkwood-rd88f6281-a.dtb \
>> diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
>> new file mode 100644
>> index 000000000000..1db6f2c506cc
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
>> @@ -0,0 +1,178 @@
>> +/*
>> + * kirkwood-pogoplug-series-4.dts - Device tree file for PogoPlug Series 4
>> + * inspired by the board files made by Kevin Mihelich for ArchLinux,
>> + * and their DTS file.
>> + *
>> + * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "kirkwood.dtsi"
>> +#include "kirkwood-6192.dtsi"
>> +#include <dt-bindings/input/linux-event-codes.h>
>> +
>> +/ {
>> + model = "Cloud Engines PogoPlug Series 4";
>> + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
>> + "marvell,kirkwood";
>> +
>> + memory {
>> + device_type = "memory";
>> + reg = <0x00000000 0x08000000>;
>> + };
>> +
>> + chosen {
>> + stdout-path = "uart0:115200n8";
>> + };
>> +
>> + gpio_keys {
>> + compatible = "gpio-keys";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-0 = <&pmx_button_eject>;
>> + pinctrl-names = "default";
>> +
>> + button at 1 {
>> + debounce_interval = <50>;
>> + wakeup-source;
>> + linux,code = <KEY_EJECTCD>;
>> + label = "Eject Button";
>> + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> + pinctrl-0 = <&pmx_led_green &pmx_led_red>;
>> + pinctrl-names = "default";
>> +
>> + health {
>> + label = "pogoplugv4:green:health";
>> + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
>> + default-state = "on";
>> + };
>> + fault {
>> + label = "pogoplugv4:red:fault";
>> + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +};
>> +
>> +&pinctrl {
>> + pmx_sata0: pmx-sata0 {
>> + marvell,pins = "mpp21";
>> + marvell,function = "sata0";
>> + };
>> +
>> + pmx_sata1: pmx-sata1 {
>> + marvell,pins = "mpp20";
>> + marvell,function = "sata1";
>> + };
>> +
>> + pmx_sdio_cd: pmx-sdio-cd {
>> + marvell,pins = "mpp27";
>> + marvell,function = "gpio";
>> + };
>> +
>> + pmx_sdio_wp: pmx-sdio-wp {
>> + marvell,pins = "mpp28";
>> + marvell,function = "gpio";
>> + };
>> +
>> + pmx_button_eject: pmx-button-eject {
>> + marvell,pins = "mpp29";
>> + marvell,function = "gpio";
>> + };
>> +
>> + pmx_led_green: pmx-led-green {
>> + marvell,pins = "mpp22";
>> + marvell,function = "gpio";
>> + };
>> +
>> + pmx_led_red: pmx-led-red {
>> + marvell,pins = "mpp24";
>> + marvell,function = "gpio";
>> + };
>> +};
>> +
>> +&uart0 {
>> + status = "okay";
>> +};
>> +
>> +/*
>> + * This PCIE controller has a USB 3.0 XHCI controller at 1,0
>> + */
>> +&pciec {
>> + status = "okay";
>> +};
>> +
>> +&pcie0 {
>> + status = "okay";
>> +};
>> +
>> +&sata {
>> + status = "okay";
>> + pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
>> + pinctrl-names = "default";
>> + nr-ports = <1>;
>> +};
>> +
>> +&sdio {
>> + status = "okay";
>> + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd &pmx_sdio_wp>;
>> + pinctrl-names = "default";
>> + cd-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
>> + wp-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
>> +};
>> +
>> +&nand {
>> + /* 128 MiB of NAND flash */
>> + chip-delay = <40>;
>> + status = "okay";
>> + partitions {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + partition at 0 {
>> + label = "u-boot";
>> + reg = <0x00000000 0x200000>;
>> + read-only;
>> + };
>> +
>> + partition at 200000 {
>> + label = "uImage";
>> + reg = <0x00200000 0x300000>;
>> + };
>> +
>> + partition at 500000 {
>> + label = "uImage2";
>> + reg = <0x00500000 0x300000>;
>> + };
>> +
>> + partition at 800000 {
>> + label = "failsafe";
>> + reg = <0x00800000 0x800000>;
>> + };
>> +
>> + partition at 1000000 {
>> + label = "root";
>> + reg = <0x01000000 0x7000000>;
>> + };
>> + };
>> +};
>> +
>> +&mdio {
>> + status = "okay";
>> +
>> + ethphy0: ethernet-phy at 0 {
>> + reg = <0>;
>> + };
>> +};
>> +
>> +ð0 {
>> + status = "okay";
>> + ethernet0-port at 0 {
>> + phy-handle = <ðphy0>;
>> + };
>> +};
>> --
>> 2.4.3
>>
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2015-12-15 16:21 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-12-14 14:32 [PATCH 0/2 v3] ARM: mvebu: kirkwood: add PogoPlug series 4 device tree Linus Walleij
2015-12-14 15:05 ` Andrew Lunn
2015-12-15 16:21 ` Gregory CLEMENT
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.