* [PATCH 1/2] arm: stm32mp: Fix USB boot device report
@ 2021-12-06 20:58 Marek Vasut
2021-12-06 20:58 ` [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery Marek Vasut
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Marek Vasut @ 2021-12-06 20:58 UTC (permalink / raw)
To: u-boot; +Cc: Marek Vasut, Patrice Chotard, Patrick Delaunay
In case the SoC reports the boot device type is USB, it means the SPL was
loaded via BootROM DFU mode. Currently the spl_boot_device() returns boot
device as USB host, change it to DFU instead, so the SPL can continue the
DFU boot and load U-Boot via DFU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
arch/arm/mach-stm32mp/spl.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/mach-stm32mp/spl.c b/arch/arm/mach-stm32mp/spl.c
index 405eff68a3b..51fe0698fab 100644
--- a/arch/arm/mach-stm32mp/spl.c
+++ b/arch/arm/mach-stm32mp/spl.c
@@ -43,7 +43,7 @@ u32 spl_boot_device(void)
case BOOT_SERIAL_UART_8:
return BOOT_DEVICE_UART;
case BOOT_SERIAL_USB_OTG:
- return BOOT_DEVICE_USB;
+ return BOOT_DEVICE_DFU;
case BOOT_FLASH_NAND_FMC:
return BOOT_DEVICE_NAND;
case BOOT_FLASH_NOR_QSPI:
--
2.33.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery
2021-12-06 20:58 [PATCH 1/2] arm: stm32mp: Fix USB boot device report Marek Vasut
@ 2021-12-06 20:58 ` Marek Vasut
2021-12-07 10:02 ` Patrice CHOTARD
2022-01-24 12:14 ` Patrice CHOTARD
2021-12-07 10:01 ` [PATCH 1/2] arm: stm32mp: Fix USB boot device report Patrice CHOTARD
2022-01-24 12:14 ` Patrice CHOTARD
2 siblings, 2 replies; 6+ messages in thread
From: Marek Vasut @ 2021-12-06 20:58 UTC (permalink / raw)
To: u-boot; +Cc: Marek Vasut, Patrice Chotard, Patrick Delaunay
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 42 ++++++++++++++++++++++
configs/stm32mp15_dhcor_basic_defconfig | 14 ++++++--
include/configs/stm32mp15_dh_dhsom.h | 7 ++++
3 files changed, 61 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
index 502cd95da05..71375510b4a 100644
--- a/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
@@ -27,6 +27,7 @@
&i2c4 {
u-boot,dm-pre-reloc;
+ u-boot,dm-spl;
};
&i2c4_pins_a {
@@ -38,6 +39,15 @@
&pmic {
u-boot,dm-pre-reloc;
+ u-boot,dm-spl;
+
+ regulators {
+ u-boot,dm-spl;
+ };
+};
+
+&pwr_regulators {
+ u-boot,dm-spl;
};
&qspi {
@@ -152,3 +162,35 @@
u-boot,dm-pre-reloc;
};
};
+
+®11 {
+ u-boot,dm-spl;
+};
+
+®18 {
+ u-boot,dm-spl;
+};
+
+&usbotg_hs {
+ u-boot,dm-spl;
+};
+
+&usbphyc {
+ u-boot,dm-spl;
+};
+
+&usbphyc_port0 {
+ u-boot,dm-spl;
+};
+
+&usbphyc_port1 {
+ u-boot,dm-spl;
+};
+
+&vdd_io {
+ u-boot,dm-spl;
+};
+
+&vdd_usb {
+ u-boot,dm-spl;
+};
diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
index 2356de76baf..87980d2570d 100644
--- a/configs/stm32mp15_dhcor_basic_defconfig
+++ b/configs/stm32mp15_dhcor_basic_defconfig
@@ -16,6 +16,7 @@ CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0xc2000000
CONFIG_FIT=y
CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_LOAD_FIT_ADDRESS=0xc1000000
CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its"
# CONFIG_USE_SPL_FIT_GENERATOR is not set
CONFIG_BOOTDELAY=1
@@ -25,12 +26,17 @@ CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_I2C=y
CONFIG_SPL_MTD_SUPPORT=y
CONFIG_SPL_DM_SPI_FLASH=y
CONFIG_SPL_POWER=y
+CONFIG_SPL_RAM_SUPPORT=y
+CONFIG_SPL_RAM_DEVICE=y
CONFIG_SPL_SPI_FLASH_MTD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_DFU=y
CONFIG_SYS_PROMPT="STM32MP> "
# CONFIG_CMD_ELF is not set
# CONFIG_CMD_EXPORTENV is not set
@@ -76,6 +82,7 @@ CONFIG_USE_ENV_SPI_MODE=y
CONFIG_ENV_SPI_MODE=0x0
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_ENV_IS_NOWHERE=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=1536
@@ -84,7 +91,6 @@ CONFIG_SPL_BLOCK_CACHE=y
CONFIG_DFU_MMC=y
CONFIG_DFU_MTD=y
CONFIG_DFU_RAM=y
-CONFIG_DFU_VIRT=y
CONFIG_GPIO_HOG=y
CONFIG_DM_HWSPINLOCK=y
CONFIG_HWSPINLOCK_STM32=y
@@ -113,18 +119,20 @@ CONFIG_PHY_MICREL_KSZ90X1=y
CONFIG_DM_ETH=y
CONFIG_DWC_ETH_QOS=y
CONFIG_PHY=y
+CONFIG_SPL_PHY=y
CONFIG_PHY_STM32_USBPHYC=y
CONFIG_PINCONF=y
# CONFIG_SPL_PINCTRL_FULL is not set
CONFIG_PINCTRL_STMFX=y
CONFIG_DM_PMIC=y
-# CONFIG_SPL_PMIC_CHILDREN is not set
CONFIG_PMIC_STPMIC1=y
CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_DM_REGULATOR_STM32_VREFBUF=y
CONFIG_DM_REGULATOR_STPMIC1=y
+CONFIG_SPL_DM_REGULATOR_STPMIC1=y
CONFIG_REMOTEPROC_STM32_COPRO=y
CONFIG_DM_RTC=y
CONFIG_RTC_STM32=y
@@ -136,8 +144,10 @@ CONFIG_STM32_SPI=y
CONFIG_SYSRESET_SYSCON=y
CONFIG_USB=y
CONFIG_DM_USB_GADGET=y
+CONFIG_SPL_DM_USB_GADGET=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_DWC2=y
CONFIG_USB_HOST_ETHER=y
CONFIG_USB_ETHER_ASIX=y
CONFIG_USB_GADGET=y
diff --git a/include/configs/stm32mp15_dh_dhsom.h b/include/configs/stm32mp15_dh_dhsom.h
index d2fe923a33b..9e7d4b8144f 100644
--- a/include/configs/stm32mp15_dh_dhsom.h
+++ b/include/configs/stm32mp15_dh_dhsom.h
@@ -8,6 +8,13 @@
#ifndef __CONFIG_STM32MP15_DH_DHSOM_H__
#define __CONFIG_STM32MP15_DH_DHSOM_H__
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "dfu_alt_info_ram=u-boot.itb ram " \
+ __stringify(CONFIG_SPL_LOAD_FIT_ADDRESS) \
+ " 0x800000\0"
+#endif
+
#define STM32MP_BOARD_EXTRA_ENV \
"usb_pgood_delay=1000\0" \
"update_sf=" /* Erase SPI NOR and install U-Boot from SD */ \
--
2.33.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] arm: stm32mp: Fix USB boot device report
2021-12-06 20:58 [PATCH 1/2] arm: stm32mp: Fix USB boot device report Marek Vasut
2021-12-06 20:58 ` [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery Marek Vasut
@ 2021-12-07 10:01 ` Patrice CHOTARD
2022-01-24 12:14 ` Patrice CHOTARD
2 siblings, 0 replies; 6+ messages in thread
From: Patrice CHOTARD @ 2021-12-07 10:01 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrick Delaunay
Hi Marek
On 12/6/21 9:58 PM, Marek Vasut wrote:
> In case the SoC reports the boot device type is USB, it means the SPL was
> loaded via BootROM DFU mode. Currently the spl_boot_device() returns boot
> device as USB host, change it to DFU instead, so the SPL can continue the
> DFU boot and load U-Boot via DFU.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> arch/arm/mach-stm32mp/spl.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/mach-stm32mp/spl.c b/arch/arm/mach-stm32mp/spl.c
> index 405eff68a3b..51fe0698fab 100644
> --- a/arch/arm/mach-stm32mp/spl.c
> +++ b/arch/arm/mach-stm32mp/spl.c
> @@ -43,7 +43,7 @@ u32 spl_boot_device(void)
> case BOOT_SERIAL_UART_8:
> return BOOT_DEVICE_UART;
> case BOOT_SERIAL_USB_OTG:
> - return BOOT_DEVICE_USB;
> + return BOOT_DEVICE_DFU;
> case BOOT_FLASH_NAND_FMC:
> return BOOT_DEVICE_NAND;
> case BOOT_FLASH_NOR_QSPI:
>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Thanks
Patrice
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery
2021-12-06 20:58 ` [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery Marek Vasut
@ 2021-12-07 10:02 ` Patrice CHOTARD
2022-01-24 12:14 ` Patrice CHOTARD
1 sibling, 0 replies; 6+ messages in thread
From: Patrice CHOTARD @ 2021-12-07 10:02 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrick Delaunay
Hi Marek
On 12/6/21 9:58 PM, Marek Vasut wrote:
> This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
> SPL and subsequent u-boot.itb for recovery or commissioning purposes.
>
> To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
> - Install dfu-util on the host PC (in debian this is package 'dfu-util')
>
> - Power off the Avenger96 board.
> - Connect both USB-serial console and USB-OTG microB ports to host PC.
> - Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
> - Power on the Avenger96 board.
> - Verify using '$ dmesg' that a new device has been detected as follows:
> New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
> New USB device strings: Mfr=1, Product=2, SerialNumber=3
> Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
> Manufacturer: STMicroelectronics
>
> - Upload U-Boot SPL:
> $ dfu-util -a 1 -D u-boot-spl.stm32
> - Upload U-Boot proper:
> $ dfu-util -a 0 -D u-boot.itb
>
> - At this point, SPL will wait for user to press "Ctrl-C" on serial
> console. When ready to interact with U-Boot, press Ctrl-C to start
> the bootloader.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 42 ++++++++++++++++++++++
> configs/stm32mp15_dhcor_basic_defconfig | 14 ++++++--
> include/configs/stm32mp15_dh_dhsom.h | 7 ++++
> 3 files changed, 61 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> index 502cd95da05..71375510b4a 100644
> --- a/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> @@ -27,6 +27,7 @@
>
> &i2c4 {
> u-boot,dm-pre-reloc;
> + u-boot,dm-spl;
> };
>
> &i2c4_pins_a {
> @@ -38,6 +39,15 @@
>
> &pmic {
> u-boot,dm-pre-reloc;
> + u-boot,dm-spl;
> +
> + regulators {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&pwr_regulators {
> + u-boot,dm-spl;
> };
>
> &qspi {
> @@ -152,3 +162,35 @@
> u-boot,dm-pre-reloc;
> };
> };
> +
> +®11 {
> + u-boot,dm-spl;
> +};
> +
> +®18 {
> + u-boot,dm-spl;
> +};
> +
> +&usbotg_hs {
> + u-boot,dm-spl;
> +};
> +
> +&usbphyc {
> + u-boot,dm-spl;
> +};
> +
> +&usbphyc_port0 {
> + u-boot,dm-spl;
> +};
> +
> +&usbphyc_port1 {
> + u-boot,dm-spl;
> +};
> +
> +&vdd_io {
> + u-boot,dm-spl;
> +};
> +
> +&vdd_usb {
> + u-boot,dm-spl;
> +};
> diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
> index 2356de76baf..87980d2570d 100644
> --- a/configs/stm32mp15_dhcor_basic_defconfig
> +++ b/configs/stm32mp15_dhcor_basic_defconfig
> @@ -16,6 +16,7 @@ CONFIG_DISTRO_DEFAULTS=y
> CONFIG_SYS_LOAD_ADDR=0xc2000000
> CONFIG_FIT=y
> CONFIG_SPL_LOAD_FIT=y
> +CONFIG_SPL_LOAD_FIT_ADDRESS=0xc1000000
> CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its"
> # CONFIG_USE_SPL_FIT_GENERATOR is not set
> CONFIG_BOOTDELAY=1
> @@ -25,12 +26,17 @@ CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> +CONFIG_SPL_ENV_SUPPORT=y
> CONFIG_SPL_I2C=y
> CONFIG_SPL_MTD_SUPPORT=y
> CONFIG_SPL_DM_SPI_FLASH=y
> CONFIG_SPL_POWER=y
> +CONFIG_SPL_RAM_SUPPORT=y
> +CONFIG_SPL_RAM_DEVICE=y
> CONFIG_SPL_SPI_FLASH_MTD=y
> CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
> +CONFIG_SPL_USB_GADGET=y
> +CONFIG_SPL_DFU=y
> CONFIG_SYS_PROMPT="STM32MP> "
> # CONFIG_CMD_ELF is not set
> # CONFIG_CMD_EXPORTENV is not set
> @@ -76,6 +82,7 @@ CONFIG_USE_ENV_SPI_MODE=y
> CONFIG_ENV_SPI_MODE=0x0
> CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SPL_ENV_IS_NOWHERE=y
> CONFIG_NET_RANDOM_ETHADDR=y
> CONFIG_IP_DEFRAG=y
> CONFIG_TFTP_BLOCKSIZE=1536
> @@ -84,7 +91,6 @@ CONFIG_SPL_BLOCK_CACHE=y
> CONFIG_DFU_MMC=y
> CONFIG_DFU_MTD=y
> CONFIG_DFU_RAM=y
> -CONFIG_DFU_VIRT=y
> CONFIG_GPIO_HOG=y
> CONFIG_DM_HWSPINLOCK=y
> CONFIG_HWSPINLOCK_STM32=y
> @@ -113,18 +119,20 @@ CONFIG_PHY_MICREL_KSZ90X1=y
> CONFIG_DM_ETH=y
> CONFIG_DWC_ETH_QOS=y
> CONFIG_PHY=y
> +CONFIG_SPL_PHY=y
> CONFIG_PHY_STM32_USBPHYC=y
> CONFIG_PINCONF=y
> # CONFIG_SPL_PINCTRL_FULL is not set
> CONFIG_PINCTRL_STMFX=y
> CONFIG_DM_PMIC=y
> -# CONFIG_SPL_PMIC_CHILDREN is not set
> CONFIG_PMIC_STPMIC1=y
> CONFIG_DM_REGULATOR=y
> +CONFIG_SPL_DM_REGULATOR=y
> CONFIG_DM_REGULATOR_FIXED=y
> CONFIG_DM_REGULATOR_GPIO=y
> CONFIG_DM_REGULATOR_STM32_VREFBUF=y
> CONFIG_DM_REGULATOR_STPMIC1=y
> +CONFIG_SPL_DM_REGULATOR_STPMIC1=y
> CONFIG_REMOTEPROC_STM32_COPRO=y
> CONFIG_DM_RTC=y
> CONFIG_RTC_STM32=y
> @@ -136,8 +144,10 @@ CONFIG_STM32_SPI=y
> CONFIG_SYSRESET_SYSCON=y
> CONFIG_USB=y
> CONFIG_DM_USB_GADGET=y
> +CONFIG_SPL_DM_USB_GADGET=y
> CONFIG_USB_EHCI_HCD=y
> CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_DWC2=y
> CONFIG_USB_HOST_ETHER=y
> CONFIG_USB_ETHER_ASIX=y
> CONFIG_USB_GADGET=y
> diff --git a/include/configs/stm32mp15_dh_dhsom.h b/include/configs/stm32mp15_dh_dhsom.h
> index d2fe923a33b..9e7d4b8144f 100644
> --- a/include/configs/stm32mp15_dh_dhsom.h
> +++ b/include/configs/stm32mp15_dh_dhsom.h
> @@ -8,6 +8,13 @@
> #ifndef __CONFIG_STM32MP15_DH_DHSOM_H__
> #define __CONFIG_STM32MP15_DH_DHSOM_H__
>
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "dfu_alt_info_ram=u-boot.itb ram " \
> + __stringify(CONFIG_SPL_LOAD_FIT_ADDRESS) \
> + " 0x800000\0"
> +#endif
> +
> #define STM32MP_BOARD_EXTRA_ENV \
> "usb_pgood_delay=1000\0" \
> "update_sf=" /* Erase SPI NOR and install U-Boot from SD */ \
>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Thanks
Patrice
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] arm: stm32mp: Fix USB boot device report
2021-12-06 20:58 [PATCH 1/2] arm: stm32mp: Fix USB boot device report Marek Vasut
2021-12-06 20:58 ` [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery Marek Vasut
2021-12-07 10:01 ` [PATCH 1/2] arm: stm32mp: Fix USB boot device report Patrice CHOTARD
@ 2022-01-24 12:14 ` Patrice CHOTARD
2 siblings, 0 replies; 6+ messages in thread
From: Patrice CHOTARD @ 2022-01-24 12:14 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrick Delaunay
Hi Marek
On 12/6/21 21:58, Marek Vasut wrote:
> In case the SoC reports the boot device type is USB, it means the SPL was
> loaded via BootROM DFU mode. Currently the spl_boot_device() returns boot
> device as USB host, change it to DFU instead, so the SPL can continue the
> DFU boot and load U-Boot via DFU.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> arch/arm/mach-stm32mp/spl.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/mach-stm32mp/spl.c b/arch/arm/mach-stm32mp/spl.c
> index 405eff68a3b..51fe0698fab 100644
> --- a/arch/arm/mach-stm32mp/spl.c
> +++ b/arch/arm/mach-stm32mp/spl.c
> @@ -43,7 +43,7 @@ u32 spl_boot_device(void)
> case BOOT_SERIAL_UART_8:
> return BOOT_DEVICE_UART;
> case BOOT_SERIAL_USB_OTG:
> - return BOOT_DEVICE_USB;
> + return BOOT_DEVICE_DFU;
> case BOOT_FLASH_NAND_FMC:
> return BOOT_DEVICE_NAND;
> case BOOT_FLASH_NOR_QSPI:
Applied to u-boot-stm/master
Thanks
Patrice
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery
2021-12-06 20:58 ` [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery Marek Vasut
2021-12-07 10:02 ` Patrice CHOTARD
@ 2022-01-24 12:14 ` Patrice CHOTARD
1 sibling, 0 replies; 6+ messages in thread
From: Patrice CHOTARD @ 2022-01-24 12:14 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrick Delaunay
Hi Marek
On 12/6/21 21:58, Marek Vasut wrote:
> This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
> SPL and subsequent u-boot.itb for recovery or commissioning purposes.
>
> To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
> - Install dfu-util on the host PC (in debian this is package 'dfu-util')
>
> - Power off the Avenger96 board.
> - Connect both USB-serial console and USB-OTG microB ports to host PC.
> - Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
> - Power on the Avenger96 board.
> - Verify using '$ dmesg' that a new device has been detected as follows:
> New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
> New USB device strings: Mfr=1, Product=2, SerialNumber=3
> Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
> Manufacturer: STMicroelectronics
>
> - Upload U-Boot SPL:
> $ dfu-util -a 1 -D u-boot-spl.stm32
> - Upload U-Boot proper:
> $ dfu-util -a 0 -D u-boot.itb
>
> - At this point, SPL will wait for user to press "Ctrl-C" on serial
> console. When ready to interact with U-Boot, press Ctrl-C to start
> the bootloader.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 42 ++++++++++++++++++++++
> configs/stm32mp15_dhcor_basic_defconfig | 14 ++++++--
> include/configs/stm32mp15_dh_dhsom.h | 7 ++++
> 3 files changed, 61 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> index 502cd95da05..71375510b4a 100644
> --- a/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> @@ -27,6 +27,7 @@
>
> &i2c4 {
> u-boot,dm-pre-reloc;
> + u-boot,dm-spl;
> };
>
> &i2c4_pins_a {
> @@ -38,6 +39,15 @@
>
> &pmic {
> u-boot,dm-pre-reloc;
> + u-boot,dm-spl;
> +
> + regulators {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&pwr_regulators {
> + u-boot,dm-spl;
> };
>
> &qspi {
> @@ -152,3 +162,35 @@
> u-boot,dm-pre-reloc;
> };
> };
> +
> +®11 {
> + u-boot,dm-spl;
> +};
> +
> +®18 {
> + u-boot,dm-spl;
> +};
> +
> +&usbotg_hs {
> + u-boot,dm-spl;
> +};
> +
> +&usbphyc {
> + u-boot,dm-spl;
> +};
> +
> +&usbphyc_port0 {
> + u-boot,dm-spl;
> +};
> +
> +&usbphyc_port1 {
> + u-boot,dm-spl;
> +};
> +
> +&vdd_io {
> + u-boot,dm-spl;
> +};
> +
> +&vdd_usb {
> + u-boot,dm-spl;
> +};
> diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
> index 2356de76baf..87980d2570d 100644
> --- a/configs/stm32mp15_dhcor_basic_defconfig
> +++ b/configs/stm32mp15_dhcor_basic_defconfig
> @@ -16,6 +16,7 @@ CONFIG_DISTRO_DEFAULTS=y
> CONFIG_SYS_LOAD_ADDR=0xc2000000
> CONFIG_FIT=y
> CONFIG_SPL_LOAD_FIT=y
> +CONFIG_SPL_LOAD_FIT_ADDRESS=0xc1000000
> CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its"
> # CONFIG_USE_SPL_FIT_GENERATOR is not set
> CONFIG_BOOTDELAY=1
> @@ -25,12 +26,17 @@ CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> +CONFIG_SPL_ENV_SUPPORT=y
> CONFIG_SPL_I2C=y
> CONFIG_SPL_MTD_SUPPORT=y
> CONFIG_SPL_DM_SPI_FLASH=y
> CONFIG_SPL_POWER=y
> +CONFIG_SPL_RAM_SUPPORT=y
> +CONFIG_SPL_RAM_DEVICE=y
> CONFIG_SPL_SPI_FLASH_MTD=y
> CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
> +CONFIG_SPL_USB_GADGET=y
> +CONFIG_SPL_DFU=y
> CONFIG_SYS_PROMPT="STM32MP> "
> # CONFIG_CMD_ELF is not set
> # CONFIG_CMD_EXPORTENV is not set
> @@ -76,6 +82,7 @@ CONFIG_USE_ENV_SPI_MODE=y
> CONFIG_ENV_SPI_MODE=0x0
> CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SPL_ENV_IS_NOWHERE=y
> CONFIG_NET_RANDOM_ETHADDR=y
> CONFIG_IP_DEFRAG=y
> CONFIG_TFTP_BLOCKSIZE=1536
> @@ -84,7 +91,6 @@ CONFIG_SPL_BLOCK_CACHE=y
> CONFIG_DFU_MMC=y
> CONFIG_DFU_MTD=y
> CONFIG_DFU_RAM=y
> -CONFIG_DFU_VIRT=y
> CONFIG_GPIO_HOG=y
> CONFIG_DM_HWSPINLOCK=y
> CONFIG_HWSPINLOCK_STM32=y
> @@ -113,18 +119,20 @@ CONFIG_PHY_MICREL_KSZ90X1=y
> CONFIG_DM_ETH=y
> CONFIG_DWC_ETH_QOS=y
> CONFIG_PHY=y
> +CONFIG_SPL_PHY=y
> CONFIG_PHY_STM32_USBPHYC=y
> CONFIG_PINCONF=y
> # CONFIG_SPL_PINCTRL_FULL is not set
> CONFIG_PINCTRL_STMFX=y
> CONFIG_DM_PMIC=y
> -# CONFIG_SPL_PMIC_CHILDREN is not set
> CONFIG_PMIC_STPMIC1=y
> CONFIG_DM_REGULATOR=y
> +CONFIG_SPL_DM_REGULATOR=y
> CONFIG_DM_REGULATOR_FIXED=y
> CONFIG_DM_REGULATOR_GPIO=y
> CONFIG_DM_REGULATOR_STM32_VREFBUF=y
> CONFIG_DM_REGULATOR_STPMIC1=y
> +CONFIG_SPL_DM_REGULATOR_STPMIC1=y
> CONFIG_REMOTEPROC_STM32_COPRO=y
> CONFIG_DM_RTC=y
> CONFIG_RTC_STM32=y
> @@ -136,8 +144,10 @@ CONFIG_STM32_SPI=y
> CONFIG_SYSRESET_SYSCON=y
> CONFIG_USB=y
> CONFIG_DM_USB_GADGET=y
> +CONFIG_SPL_DM_USB_GADGET=y
> CONFIG_USB_EHCI_HCD=y
> CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_DWC2=y
> CONFIG_USB_HOST_ETHER=y
> CONFIG_USB_ETHER_ASIX=y
> CONFIG_USB_GADGET=y
> diff --git a/include/configs/stm32mp15_dh_dhsom.h b/include/configs/stm32mp15_dh_dhsom.h
> index d2fe923a33b..9e7d4b8144f 100644
> --- a/include/configs/stm32mp15_dh_dhsom.h
> +++ b/include/configs/stm32mp15_dh_dhsom.h
> @@ -8,6 +8,13 @@
> #ifndef __CONFIG_STM32MP15_DH_DHSOM_H__
> #define __CONFIG_STM32MP15_DH_DHSOM_H__
>
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "dfu_alt_info_ram=u-boot.itb ram " \
> + __stringify(CONFIG_SPL_LOAD_FIT_ADDRESS) \
> + " 0x800000\0"
> +#endif
> +
> #define STM32MP_BOARD_EXTRA_ENV \
> "usb_pgood_delay=1000\0" \
> "update_sf=" /* Erase SPI NOR and install U-Boot from SD */ \
Applied to u-boot-stm/master
Thanks
Patrice
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2022-01-24 12:14 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-12-06 20:58 [PATCH 1/2] arm: stm32mp: Fix USB boot device report Marek Vasut
2021-12-06 20:58 ` [PATCH 2/2] ARM: dts: stm32: Add DFU support for DHCOR recovery Marek Vasut
2021-12-07 10:02 ` Patrice CHOTARD
2022-01-24 12:14 ` Patrice CHOTARD
2021-12-07 10:01 ` [PATCH 1/2] arm: stm32mp: Fix USB boot device report Patrice CHOTARD
2022-01-24 12:14 ` Patrice CHOTARD
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.