[PATCH v2] dt-bindings: memory-controller: st,stm32: Split off MC properties

* [PATCH v2] dt-bindings: memory-controller: st,stm32: Split off MC properties
@ 2022-09-26 22:55 ` Marek Vasut
  0 siblings, 0 replies; 14+ messages in thread
From: Marek Vasut @ 2022-09-26 22:55 UTC (permalink / raw)
  To: linux-arm-kernel
  Cc: Marek Vasut, Rob Herring, Alexandre Torgue, Christophe Kerello,
	Krzysztof Kozlowski, Linus Walleij, Maxime Coquelin, Rob Herring,
	devicetree, linux-stm32

Split st,stm32-fmc2-ebi.yaml specific properties into st,stm32-fmc2-ebi-props.yaml ,
split memory-controller bus peripheral properties into mc-peripheral-props.yaml ,
reference the st,stm32-fmc2-ebi-props.yaml in mc-peripheral-props.yaml and
reference the mc-peripheral-props.yaml in micrel,ks8851.yaml .

This way, the FMC2 controller properties in Micrel KSZ8851MLL ethernet
controller node can be properly validated.

Fixes the following warning:

"
arch/arm/boot/dts/stm32mp153c-dhcor-drc-compact.dtb: ethernet@1,0: Unevaluated properties are not allowed ('bank-width', 'st,fmc2-ebi-cs-mux-enable', 'st,fmc2-ebi-cs-transaction-type', 'st,fmc2-ebi-cs-buswidth', 'st,fmc2-ebi-cs-address-setup-ns', 'st,fmc2-ebi-cs-address-hold-ns', 'st,fmc2-ebi-cs-bus-turnaround-ns', 'st,fmc2-ebi-cs-data-setup-ns', 'st,fmc2-ebi-cs-data-hold-ns', 'st,fmc2-ebi-cs-write-address-setup-ns', 'st,fmc2-ebi-cs-write-address-hold-ns', 'st,fmc2-ebi-cs-write-bus-turnaround-ns', 'st,fmc2-ebi-cs-write-data-setup-ns', 'st,fmc2-ebi-cs-write-data-hold-ns' were unexpected)
"

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
---
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Christophe Kerello <christophe.kerello@foss.st.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: - Depends on bugfix [PATCH] dt-bindings: memory-controller: st,stm32: Fix st,fmc2_ebi-cs-write-address-setup-ns
    - Replace MC controllers with Memory Controllers
    - Add type uint32 and enum 1,2,4 to bank-width prop
    - Add RB from Rob
---
 .../mc-peripheral-props.yaml                  |  38 +++++
 .../st,stm32-fmc2-ebi-props.yaml              | 144 ++++++++++++++++++
 .../memory-controllers/st,stm32-fmc2-ebi.yaml | 137 -----------------
 .../bindings/net/micrel,ks8851.yaml           |   1 +
 4 files changed, 183 insertions(+), 137 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml

diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
new file mode 100644
index 0000000000000..53ae995462db7
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/mc-peripheral-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral-specific properties for a Memory Controller bus.
+
+description:
+  Many Memory Controllers need to add properties to peripheral devices.
+  They could be common properties like reg or they could be controller
+  specific like delay in clock or data lines, etc. These properties need
+  to be defined in the peripheral node because they are per-peripheral
+  and there can be multiple peripherals attached to a controller. All
+  those properties are listed here. The controller specific properties
+  should go in their own separate schema that should be referenced
+  from here.
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+properties:
+  reg:
+    description: Bank number, base address and size of the device.
+
+  bank-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Bank width of the device, in bytes.
+    enum: [1, 2, 4]
+
+required:
+  - reg
+
+# The controller specific properties go here.
+allOf:
+  - $ref: st,stm32-fmc2-ebi-props.yaml#
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml
new file mode 100644
index 0000000000000..475e4095068c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral properties for ST FMC2 Controller
+
+maintainers:
+  - Christophe Kerello <christophe.kerello@foss.st.com>
+  - Marek Vasut <marex@denx.de>
+
+properties:
+  st,fmc2-ebi-cs-transaction-type:
+    description: |
+      Select one of the transactions type supported
+      0: Asynchronous mode 1 SRAM/FRAM.
+      1: Asynchronous mode 1 PSRAM.
+      2: Asynchronous mode A SRAM/FRAM.
+      3: Asynchronous mode A PSRAM.
+      4: Asynchronous mode 2 NOR.
+      5: Asynchronous mode B NOR.
+      6: Asynchronous mode C NOR.
+      7: Asynchronous mode D NOR.
+      8: Synchronous read synchronous write PSRAM.
+      9: Synchronous read asynchronous write PSRAM.
+      10: Synchronous read synchronous write NOR.
+      11: Synchronous read asynchronous write NOR.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 11
+
+  st,fmc2-ebi-cs-cclk-enable:
+    description: Continuous clock enable (first bank must be configured
+      in synchronous mode). The FMC_CLK is generated continuously
+      during asynchronous and synchronous access. By default, the
+      FMC_CLK is only generated during synchronous access.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-mux-enable:
+    description: Address/Data multiplexed on databus (valid only with
+      NOR and PSRAM transactions type). By default, Address/Data
+      are not multiplexed.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-buswidth:
+    description: Data bus width
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 8, 16 ]
+    default: 16
+
+  st,fmc2-ebi-cs-waitpol-high:
+    description: Wait signal polarity (NWAIT signal active high).
+      By default, NWAIT is active low.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-waitcfg-enable:
+    description: The NWAIT signal indicates wheither the data from the
+      device are valid or if a wait state must be inserted when accessing
+      the device in synchronous mode. By default, the NWAIT signal is
+      active one data cycle before wait state.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-wait-enable:
+    description: The NWAIT signal is enabled (its level is taken into
+      account after the programmed latency period to insert wait states
+      if asserted). By default, the NWAIT signal is disabled.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-asyncwait-enable:
+    description: The NWAIT signal is taken into account during asynchronous
+      transactions. By default, the NWAIT signal is not taken into account
+      during asynchronous transactions.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-cpsize:
+    description: CRAM page size. The controller splits the burst access
+      when the memory page is reached. By default, no burst split when
+      crossing page boundary.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 128, 256, 512, 1024 ]
+    default: 0
+
+  st,fmc2-ebi-cs-byte-lane-setup-ns:
+    description: This property configures the byte lane setup timing
+      defined in nanoseconds from NBLx low to Chip Select NEx low.
+
+  st,fmc2-ebi-cs-address-setup-ns:
+    description: This property defines the duration of the address setup
+      phase in nanoseconds used for asynchronous read/write transactions.
+
+  st,fmc2-ebi-cs-address-hold-ns:
+    description: This property defines the duration of the address hold
+      phase in nanoseconds used for asynchronous multiplexed read/write
+      transactions.
+
+  st,fmc2-ebi-cs-data-setup-ns:
+    description: This property defines the duration of the data setup phase
+      in nanoseconds used for asynchronous read/write transactions.
+
+  st,fmc2-ebi-cs-bus-turnaround-ns:
+    description: This property defines the delay in nanoseconds between the
+      end of current read/write transaction and the next transaction.
+
+  st,fmc2-ebi-cs-data-hold-ns:
+    description: This property defines the duration of the data hold phase
+      in nanoseconds used for asynchronous read/write transactions.
+
+  st,fmc2-ebi-cs-clk-period-ns:
+    description: This property defines the FMC_CLK output signal period in
+      nanoseconds.
+
+  st,fmc2-ebi-cs-data-latency-ns:
+    description: This property defines the data latency before reading or
+      writing the first data in nanoseconds.
+
+  st,fmc2-ebi-cs-write-address-setup-ns:
+    description: This property defines the duration of the address setup
+      phase in nanoseconds used for asynchronous write transactions.
+
+  st,fmc2-ebi-cs-write-address-hold-ns:
+    description: This property defines the duration of the address hold
+      phase in nanoseconds used for asynchronous multiplexed write
+      transactions.
+
+  st,fmc2-ebi-cs-write-data-setup-ns:
+    description: This property defines the duration of the data setup
+      phase in nanoseconds used for asynchronous write transactions.
+
+  st,fmc2-ebi-cs-write-bus-turnaround-ns:
+    description: This property defines the delay between the end of current
+      write transaction and the next transaction in nanoseconds.
+
+  st,fmc2-ebi-cs-write-data-hold-ns:
+    description: This property defines the duration of the data hold phase
+      in nanoseconds used for asynchronous write transactions.
+
+  st,fmc2-ebi-cs-max-low-pulse-ns:
+    description: This property defines the maximum chip select low pulse
+      duration in nanoseconds for synchronous transactions. When this timing
+      reaches 0, the controller splits the current access, toggles NE to
+      allow device refresh and restarts a new access.
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
index a1f535cececcc..49243f447eb90 100644
--- a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
@@ -49,143 +49,6 @@ patternProperties:
   "^.*@[0-4],[a-f0-9]+$":
     type: object
 
-    properties:
-      reg:
-        description: Bank number, base address and size of the device.
-
-      st,fmc2-ebi-cs-transaction-type:
-        description: |
-          Select one of the transactions type supported
-          0: Asynchronous mode 1 SRAM/FRAM.
-          1: Asynchronous mode 1 PSRAM.
-          2: Asynchronous mode A SRAM/FRAM.
-          3: Asynchronous mode A PSRAM.
-          4: Asynchronous mode 2 NOR.
-          5: Asynchronous mode B NOR.
-          6: Asynchronous mode C NOR.
-          7: Asynchronous mode D NOR.
-          8: Synchronous read synchronous write PSRAM.
-          9: Synchronous read asynchronous write PSRAM.
-          10: Synchronous read synchronous write NOR.
-          11: Synchronous read asynchronous write NOR.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        minimum: 0
-        maximum: 11
-
-      st,fmc2-ebi-cs-cclk-enable:
-        description: Continuous clock enable (first bank must be configured
-          in synchronous mode). The FMC_CLK is generated continuously
-          during asynchronous and synchronous access. By default, the
-          FMC_CLK is only generated during synchronous access.
-        $ref: /schemas/types.yaml#/definitions/flag
-
-      st,fmc2-ebi-cs-mux-enable:
-        description: Address/Data multiplexed on databus (valid only with
-          NOR and PSRAM transactions type). By default, Address/Data
-          are not multiplexed.
-        $ref: /schemas/types.yaml#/definitions/flag
-
-      st,fmc2-ebi-cs-buswidth:
-        description: Data bus width
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [ 8, 16 ]
-        default: 16
-
-      st,fmc2-ebi-cs-waitpol-high:
-        description: Wait signal polarity (NWAIT signal active high).
-          By default, NWAIT is active low.
-        $ref: /schemas/types.yaml#/definitions/flag
-
-      st,fmc2-ebi-cs-waitcfg-enable:
-        description: The NWAIT signal indicates wheither the data from the
-          device are valid or if a wait state must be inserted when accessing
-          the device in synchronous mode. By default, the NWAIT signal is
-          active one data cycle before wait state.
-        $ref: /schemas/types.yaml#/definitions/flag
-
-      st,fmc2-ebi-cs-wait-enable:
-        description: The NWAIT signal is enabled (its level is taken into
-          account after the programmed latency period to insert wait states
-          if asserted). By default, the NWAIT signal is disabled.
-        $ref: /schemas/types.yaml#/definitions/flag
-
-      st,fmc2-ebi-cs-asyncwait-enable:
-        description: The NWAIT signal is taken into account during asynchronous
-          transactions. By default, the NWAIT signal is not taken into account
-          during asynchronous transactions.
-        $ref: /schemas/types.yaml#/definitions/flag
-
-      st,fmc2-ebi-cs-cpsize:
-        description: CRAM page size. The controller splits the burst access
-          when the memory page is reached. By default, no burst split when
-          crossing page boundary.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [ 0, 128, 256, 512, 1024 ]
-        default: 0
-
-      st,fmc2-ebi-cs-byte-lane-setup-ns:
-        description: This property configures the byte lane setup timing
-          defined in nanoseconds from NBLx low to Chip Select NEx low.
-
-      st,fmc2-ebi-cs-address-setup-ns:
-        description: This property defines the duration of the address setup
-          phase in nanoseconds used for asynchronous read/write transactions.
-
-      st,fmc2-ebi-cs-address-hold-ns:
-        description: This property defines the duration of the address hold
-          phase in nanoseconds used for asynchronous multiplexed read/write
-          transactions.
-
-      st,fmc2-ebi-cs-data-setup-ns:
-        description: This property defines the duration of the data setup phase
-          in nanoseconds used for asynchronous read/write transactions.
-
-      st,fmc2-ebi-cs-bus-turnaround-ns:
-        description: This property defines the delay in nanoseconds between the
-          end of current read/write transaction and the next transaction.
-
-      st,fmc2-ebi-cs-data-hold-ns:
-        description: This property defines the duration of the data hold phase
-          in nanoseconds used for asynchronous read/write transactions.
-
-      st,fmc2-ebi-cs-clk-period-ns:
-        description: This property defines the FMC_CLK output signal period in
-          nanoseconds.
-
-      st,fmc2-ebi-cs-data-latency-ns:
-        description: This property defines the data latency before reading or
-          writing the first data in nanoseconds.
-
-      st,fmc2-ebi-cs-write-address-setup-ns:
-        description: This property defines the duration of the address setup
-          phase in nanoseconds used for asynchronous write transactions.
-
-      st,fmc2-ebi-cs-write-address-hold-ns:
-        description: This property defines the duration of the address hold
-          phase in nanoseconds used for asynchronous multiplexed write
-          transactions.
-
-      st,fmc2-ebi-cs-write-data-setup-ns:
-        description: This property defines the duration of the data setup
-          phase in nanoseconds used for asynchronous write transactions.
-
-      st,fmc2-ebi-cs-write-bus-turnaround-ns:
-        description: This property defines the delay between the end of current
-          write transaction and the next transaction in nanoseconds.
-
-      st,fmc2-ebi-cs-write-data-hold-ns:
-        description: This property defines the duration of the data hold phase
-          in nanoseconds used for asynchronous write transactions.
-
-      st,fmc2-ebi-cs-max-low-pulse-ns:
-        description: This property defines the maximum chip select low pulse
-          duration in nanoseconds for synchronous transactions. When this timing
-          reaches 0, the controller splits the current access, toggles NE to
-          allow device refresh and restarts a new access.
-
-    required:
-      - reg
-
 required:
   - "#address-cells"
   - "#size-cells"
diff --git a/Documentation/devicetree/bindings/net/micrel,ks8851.yaml b/Documentation/devicetree/bindings/net/micrel,ks8851.yaml
index 5aa7cf2eacb1a..b44d83554ef57 100644
--- a/Documentation/devicetree/bindings/net/micrel,ks8851.yaml
+++ b/Documentation/devicetree/bindings/net/micrel,ks8851.yaml
@@ -44,6 +44,7 @@ required:
 
 allOf:
   - $ref: ethernet-controller.yaml#
+  - $ref: /schemas/memory-controllers/mc-peripheral-props.yaml#
   - if:
       properties:
         compatible:
-- 
2.35.1


^ permalink raw reply related	[flat|nested] 14+ messages in thread