[PATCH 2/3] omap: craneboard: support the TPS65910 PMU

[PATCH 2/3] omap: craneboard: support the TPS65910 PMU

[Kim, Milo]

 This patch supports the TPS65910 PMU function on the AM3517 Craneboard.
 The IRQ pin, SYS_NIRQ is dedicated connection between the AM3517 and
 the TPS65910 PMU.
 To handle the PMU IRQs, mux configuration is required.

 Platform data configuration:
 .IRQ number : SYS_NIRQ (M_IRQ_7)
 .External clock source : external 32KHz clock is connected

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
---
 arch/arm/mach-omap2/board-am3517crane.c |   21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 37646e5..82805de 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -20,6 +20,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/gpio.h>
+#include <linux/mfd/tps65910.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
@@ -41,6 +42,7 @@
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -86,6 +88,24 @@ static struct mtd_partition crane_nand_partitions[] = {
 	},
 };
 
+static struct tps65910_board tps65910_pdata = {
+	.irq = 7 + OMAP_INTC_START,
+	.en_ck32k_xtal = true,
+};
+
+static struct i2c_board_info __initdata tps65910_board_info[] = {
+	{
+		I2C_BOARD_INFO("tps65910", 0x2d),
+		.platform_data = &tps65910_pdata,
+	},
+};
+
+static void __init am3517_crane_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, tps65910_board_info,
+			ARRAY_SIZE(tps65910_board_info));
+}
+
 static void __init am3517_crane_init(void)
 {
 	int ret;
@@ -96,6 +116,7 @@ static void __init am3517_crane_init(void)
 	board_nand_init(crane_nand_partitions,
 			ARRAY_SIZE(crane_nand_partitions), 0,
 			NAND_BUSWIDTH_16, NULL);
+	am3517_crane_i2c_init();
 
 	/* Configure GPIO for EHCI port */
 	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
-- 
1.7.9.5


Best Regards,
Milo

Re: [PATCH 2/3] omap: craneboard: support the TPS65910 PMU

[Tony Lindgren]

* Kim, Milo <Milo.Kim@ti.com> [121128 22:44]:
>  This patch supports the TPS65910 PMU function on the AM3517 Craneboard.
>  The IRQ pin, SYS_NIRQ is dedicated connection between the AM3517 and
>  the TPS65910 PMU.
>  To handle the PMU IRQs, mux configuration is required.
> 
>  Platform data configuration:
>  .IRQ number : SYS_NIRQ (M_IRQ_7)
>  .External clock source : external 32KHz clock is connected

Thanks applying 1 and 2 into omap-for-v3.9/board. Did not
see patch 3 of this anywhere?

Anyways, let's plan on making this work with device tree and
keep the changes to the board-*.c files to minimum.

Regards,

Tony

RE: [PATCH 2/3] omap: craneboard: support the TPS65910 PMU

[Kim, Milo]

> Thanks applying 1 and 2 into omap-for-v3.9/board. Did not
> see patch 3 of this anywhere?

Thank you.

The third patch is for the TPS65910 PMU on the Craneboard.
It was already applied.
https://lkml.org/lkml/2012/11/30/192

Regards,
Milo