[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Reinhard Meyer]

Hello,

I would like to generalize that driver and make it also
CONFIG_NET_MULTI-able.

Currently it contains hard coded functionality for the LPC2292 Cpu
and is used by only two boards: lpc2292sodimm and SMN42.

Since the driver could be clearly generic, using just SPI and two I/O 
Pins for
/reset and /select (the latter could be considered part of SPI), it would
make sense to ban out any board specific code from it.

When I do that, clearly I cannot test the two above boards for continued
functionality.

Messing up the driver with #ifdefs to keep old code parallel
to new one does not look like a nice approach either.

How to proceed?

Reinhard

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Wolfgang Denk]

Dear Reinhard Meyer,

In message <4C4A8404.6030302@emk-elektronik.de> you wrote:
> 
> I would like to generalize that driver and make it also
> CONFIG_NET_MULTI-able.
...
> When I do that, clearly I cannot test the two above boards for continued
> functionality.
> 
> Messing up the driver with #ifdefs to keep old code parallel
> to new one does not look like a nice approach either.

Submit patches, and put the board maintainers (if there are any) on
Cc:

If nobody complains the patches go in.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Karl's version of Parkinson's Law: Work expands to  exceed  the  time
alloted it.

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Reinhard Meyer]

Wolfgang Denk wrote:
> Submit patches, and put the board maintainers (if there are any) on
> Cc:
>
> If nobody complains the patches go in.
>   
Hello,

making the source adhere to coding style,
removing wrappers that only change function names,
and making it CONFIG_NET_MULTI-able seems to change almost every
line in the source. Would it not be better to introduce it as a new driver
and phase out the old one after a while?

Another issue is that the source has roughly 200 lines #defining the
chips register layout. Those could be moved to a header file
named "enc28j60.h". Where should that file be?
drivers/net - like most other drivers?

I also need some shared function prototypes between driver and
a board specific file, example for
int enc28j60_eth_initialize(int id, unsigned int phy_addr)
where should that go?

Reinhard

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Mike Frysinger]

On Saturday, July 24, 2010 02:11:16 Reinhard Meyer wrote:
> I would like to generalize that driver and make it also
> CONFIG_NET_MULTI-able.

someone already has ... look at the archives in december of 09
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100725/606d682b/attachment.pgp 

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Reinhard Meyer]

Mike Frysinger wrote:
> On Saturday, July 24, 2010 02:11:16 Reinhard Meyer wrote:
>   
>> I would like to generalize that driver and make it also
>> CONFIG_NET_MULTI-able.
>>     
>
> someone already has ... look at the archives in december of 09
>   
Thanks for the hint Mike,
it seems the thread there has died, and the work left incomplete however.
But it gives a head start to complete it.
The main issue I had is already proposed in that thread: rename the old 
driver and make a new one :)
Reinhard

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Mike Frysinger]

On Sunday, July 25, 2010 16:06:31 Reinhard Meyer wrote:
> Mike Frysinger wrote:
> > On Saturday, July 24, 2010 02:11:16 Reinhard Meyer wrote:
> >> I would like to generalize that driver and make it also
> >> CONFIG_NET_MULTI-able.
> > 
> > someone already has ... look at the archives in december of 09
> 
> Thanks for the hint Mike,
> it seems the thread there has died, and the work left incomplete however.
> But it gives a head start to complete it.
> The main issue I had is already proposed in that thread: rename the old
> driver and make a new one :)

best to continue that work though rather than try and start your own from 
scratch ...
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100725/adbdec3b/attachment.pgp 

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Ben Warren]

Hi Reinhard,

On Sun, Jul 25, 2010 at 1:06 PM, Reinhard Meyer <
reinhard.meyer@emk-elektronik.de> wrote:

> Mike Frysinger wrote:
> > On Saturday, July 24, 2010 02:11:16 Reinhard Meyer wrote:
> >
> >> I would like to generalize that driver and make it also
> >> CONFIG_NET_MULTI-able.
> >>
> >
> > someone already has ... look at the archives in december of 09
> >
> Thanks for the hint Mike,
> it seems the thread there has died, and the work left incomplete however.
> But it gives a head start to complete it.
> The main issue I had is already proposed in that thread: rename the old
> driver and make a new one :)
>
Then that seems like the right approach.  Create the new driver, port the
existing boards to use it and see if anybody cares.  If somebody responds,
you've found a tester.  If not, there may be some boards in the tree that
compile fine but don't run.  Not a problem I'd lose much sleep over.

> Reinhard
>
Thanks for the effort!
--Ben

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Reinhard Meyer]

Ben Warren wrote:
> Hi Reinhard,
>
> On Sun, Jul 25, 2010 at 1:06 PM, Reinhard Meyer <
> reinhard.meyer at emk-elektronik.de> wrote:
>
>   
>> Mike Frysinger wrote:
>>     
>>> On Saturday, July 24, 2010 02:11:16 Reinhard Meyer wrote:
>>>
>>>       
>>>> I would like to generalize that driver and make it also
>>>> CONFIG_NET_MULTI-able.
>>>>
>>>>         
>>> someone already has ... look at the archives in december of 09
>>>
>>>       
>> Thanks for the hint Mike,
>> it seems the thread there has died, and the work left incomplete however.
>> But it gives a head start to complete it.
>> The main issue I had is already proposed in that thread: rename the old
>> driver and make a new one :)
>>
>>     
> Then that seems like the right approach.  Create the new driver, port the
> existing boards to use it and see if anybody cares.  If somebody responds,
> you've found a tester.  If not, there may be some boards in the tree that
> compile fine but don't run.  Not a problem I'd lose much sleep over.
>   
Hello Ben,
I can rename the current driver to like "enc28j60_lpc2292.c" and make the
two affected boards use it, so they still compile and work. I can't do 
those boards' maintainers work and add the required code to use the new 
driver and make a generic spi framework for the lpc2292. They currently 
use a very private spi approach.
Or I call the new driver something like "enc28j60_generic.c".
I am definitely not going to port the existing two lpc2292 boards to use 
the new enc28j60 driver.
Reinhard

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Mike Frysinger]

On Sunday, July 25, 2010 20:07:31 Reinhard Meyer wrote:
> I can rename the current driver to like "enc28j60_lpc2292.c" and make the
> two affected boards use it, so they still compile and work. I can't do
> those boards' maintainers work and add the required code to use the new
> driver and make a generic spi framework for the lpc2292. They currently
> use a very private spi approach.
> Or I call the new driver something like "enc28j60_generic.c".
> I am definitely not going to port the existing two lpc2292 boards to use
> the new enc28j60 driver.

i prefer the former
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100725/d8f70130/attachment.pgp 

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Reinhard Meyer]

Mike Frysinger wrote:
> On Sunday, July 25, 2010 20:07:31 Reinhard Meyer wrote:
>   
>> I can rename the current driver to like "enc28j60_lpc2292.c" and make the
>> two affected boards use it, so they still compile and work. I can't do
>> those boards' maintainers work and add the required code to use the new
>> driver and make a generic spi framework for the lpc2292. They currently
>> use a very private spi approach.
>> Or I call the new driver something like "enc28j60_generic.c".
>> I am definitely not going to port the existing two lpc2292 boards to use
>> the new enc28j60 driver.
>>     
>
> i prefer the former
>   
I agree. So a first patch would be the renaming, editing the affected 
boards *.h and the Makefile in drivers/net:
COBJS-$(CONFIG_ENC28J60) += enc28j60.o
to
COBJS-$(CONFIG_ENC28J60_LPC2292) += enc28j60_lpc2292.o

In the same patch extract the 200 or so defines for the chip to 
enc28j60.h (to be used by both drivers).

One issue remains: the old driver has a lot of coding style violations, 
I can fix them, but see no point in that. The new driver will have them 
fixed.

But before I proceed I need Bens OK to go that way:)

Reinhard

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Ben Warren]

On Sunday, July 25, 2010, Reinhard Meyer
<reinhard.meyer@emk-elektronik.de> wrote:
> Mike Frysinger wrote:
>
> On Sunday, July 25, 2010 20:07:31 Reinhard Meyer wrote:
>
>
> I can rename the current driver to like "enc28j60_lpc2292.c" and make the
> two affected boards use it, so they still compile and work. I can't do
> those boards' maintainers work and add the required code to use the new
> driver and make a generic spi framework for the lpc2292. They currently
> use a very private spi approach.
> Or I call the new driver something like "enc28j60_generic.c".
> I am definitely not going to port the existing two lpc2292 boards to use
> the new enc28j60 driver.
>
>
>
> i prefer the former
>
>
> I agree. So a first patch would be the renaming, editing the affected boards *.h and the Makefile in drivers/net:
> COBJS-$(CONFIG_ENC28J60) += enc28j60.o
> to
> COBJS-$(CONFIG_ENC28J60_LPC2292) += enc28j60_lpc2292.o
>
> In the same patch extract the 200 or so defines for the chip to enc28j60.h (to be used by both drivers).
>
> One issue remains: the old driver has a lot of coding style violations, I can fix them, but see no point in that. The new driver will have them fixed.
>
> But before I proceed I need Bens OK to go that way:)
>
> Reinhard
>
Sounds good.  Go for it.

Regards,
Ben

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Mike Frysinger]

On Sunday, July 25, 2010 16:40:14 Mike Frysinger wrote:
> On Sunday, July 25, 2010 16:06:31 Reinhard Meyer wrote:
> > Mike Frysinger wrote:
> > > On Saturday, July 24, 2010 02:11:16 Reinhard Meyer wrote:
> > >> I would like to generalize that driver and make it also
> > >> CONFIG_NET_MULTI-able.
> > > 
> > > someone already has ... look at the archives in december of 09
> > 
> > Thanks for the hint Mike,
> > it seems the thread there has died, and the work left incomplete however.
> > But it gives a head start to complete it.
> > The main issue I had is already proposed in that thread: rename the old
> > driver and make a new one :)
> 
> best to continue that work though rather than try and start your own from
> scratch ...

btw, i wasnt able to test the driver previously because it required a GPIO SPI 
CS which the Blackfin SPI driver did not previously support.  but ive 
implemented & pushed that since, so i should be able to test the driver once 
you post it to make sure it does work across platforms (like Blackfin boards).
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100726/87d04b1e/attachment.pgp 

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Martin Krause]

Hi all,

u-boot-bounces at lists.denx.de wrote on Monday, July 26, 2010 4:51 PM:
> On Sunday, July 25, 2010, Reinhard Meyer
> <reinhard.meyer@emk-elektronik.de> wrote:
>> Mike Frysinger wrote:
>> 
>> On Sunday, July 25, 2010 20:07:31 Reinhard Meyer wrote:
>> 
>> 
>> I can rename the current driver to like "enc28j60_lpc2292.c" and
>> make the 
>> two affected boards use it, so they still compile and work. I can't
>> do 
>> those boards' maintainers work and add the required code to use the
>> new 
>> driver and make a generic spi framework for the lpc2292. They
>> currently 
>> use a very private spi approach.
>> Or I call the new driver something like "enc28j60_generic.c".
>> I am definitely not going to port the existing two lpc2292 boards to
>> use 
>> the new enc28j60 driver.
>> 
>> 
>> 
>> i prefer the former
>> 
>> 
>> I agree. So a first patch would be the renaming, editing the
>> affected boards *.h and the Makefile in drivers/net: 
>> COBJS-$(CONFIG_ENC28J60) += enc28j60.o
>> to
>> COBJS-$(CONFIG_ENC28J60_LPC2292) += enc28j60_lpc2292.o
>> 
>> In the same patch extract the 200 or so defines for the chip to
>> enc28j60.h (to be used by both drivers). 
>> 
>> One issue remains: the old driver has a lot of coding style
>> violations, I can fix them, but see no point in that. The new driver
>> will have them fixed.  
>> 
>> But before I proceed I need Bens OK to go that way:)
>> 
>> Reinhard
>> 
> Sounds good.  Go for it.

Some time ago I modified the current encc28j60 driver to use the
generic SPI api and to work with CONFIG_NET_MULTI. It was for a
project not part of mainline U-Boot (and a bit of a hack), so I
didn't post the patches on the mailing list.

Reinhard, if you are interested, I could send you my patch, or
post it on the mailing list.

Regards,
Martin

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Reinhard Meyer]

Martin Krause schrieb:
> Hi all,
>> Some time ago I modified the current encc28j60 driver to use the
> generic SPI api and to work with CONFIG_NET_MULTI. It was for a
> project not part of mainline U-Boot (and a bit of a hack), so I
> didn't post the patches on the mailing list.
> 
> Reinhard, if you are interested, I could send you my patch, or
> post it on the mailing list.

Yes, of course, at your discretion to the list, but if it is
not yet in "acceptable patch format" it will suffice to send it
to me. I will try to make it work on our AT91 based board
(as a 2nd LAN interface, so CONFIG_NET_MULTI will be really
required) and later submit a patch if all goes well.

Best Regards, Reinhard

[U-Boot] drivers/net/enc28j60.c - generalisation, how?

[Martin Krause]

Reinhard Meyer (-VC) wrote on Tuesday, July 27, 2010 9:29 AM:
> Martin Krause schrieb:
>> Hi all,
>>> Some time ago I modified the current encc28j60 driver to use the
>> generic SPI api and to work with CONFIG_NET_MULTI. It was for a
>> project not part of mainline U-Boot (and a bit of a hack), so I
>> didn't post the patches on the mailing list.
>> 
>> Reinhard, if you are interested, I could send you my patch, or
>> post it on the mailing list.
> 
> Yes, of course, at your discretion to the list, but if it is
> not yet in "acceptable patch format" it will suffice to send it
> to me. I will try to make it work on our AT91 based board
> (as a 2nd LAN interface, so CONFIG_NET_MULTI will be really
> required) and later submit a patch if all goes well.

OK, I send the patch directly to you, because it _is_ not in an
"acceptable patch format" for the list ...

Regards,
Martin

[U-Boot] [PATCH] NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.c

[Reinhard Meyer]

This patch is required before the upcoming new enc28j60 driver
using SPI framework patch can be applied:
- Move legacy enc28j60.c to enc28j60_lpc2292.c.
- Change Makefile and the two affected boards' definition files.

Tested with ./MAKEALL ARM7 that both boards still compile.

Signed-off-by: Reinhard Meyer <info@emk-elektronik.de>
---
 drivers/net/Makefile            |    2 +-
 drivers/net/enc28j60.c          |  982 --------------------------------------
 drivers/net/enc28j60_lpc2292.c  |  983 +++++++++++++++++++++++++++++++++++++++
 include/configs/SMN42.h         |    2 +-
 include/configs/lpc2292sodimm.h |    2 +-
 5 files changed, 986 insertions(+), 985 deletions(-)
 delete mode 100644 drivers/net/enc28j60.c
 create mode 100644 drivers/net/enc28j60_lpc2292.c

diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 218eeff..479954d 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -39,7 +39,7 @@ COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o
 COBJS-$(CONFIG_DNET) += dnet.o
 COBJS-$(CONFIG_E1000) += e1000.o
 COBJS-$(CONFIG_EEPRO100) += eepro100.o
-COBJS-$(CONFIG_ENC28J60) += enc28j60.o
+COBJS-$(CONFIG_ENC28J60_LPC2292) += enc28j60_lpc2292.o
 COBJS-$(CONFIG_EP93XX) += ep93xx_eth.o
 COBJS-$(CONFIG_ETHOC) += ethoc.o
 COBJS-$(CONFIG_FEC_MXC) += fec_mxc.o
diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c
deleted file mode 100644
index 3238a50..0000000
--- a/drivers/net/enc28j60.c
+++ /dev/null
@@ -1,982 +0,0 @@
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <common.h>
-#include <net.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spi.h>
-
-/*
- * Control Registers in Bank 0
- */
-
-#define CTL_REG_ERDPTL	 0x00
-#define CTL_REG_ERDPTH	 0x01
-#define CTL_REG_EWRPTL	 0x02
-#define CTL_REG_EWRPTH	 0x03
-#define CTL_REG_ETXSTL	 0x04
-#define CTL_REG_ETXSTH	 0x05
-#define CTL_REG_ETXNDL	 0x06
-#define CTL_REG_ETXNDH	 0x07
-#define CTL_REG_ERXSTL	 0x08
-#define CTL_REG_ERXSTH	 0x09
-#define CTL_REG_ERXNDL	 0x0A
-#define CTL_REG_ERXNDH	 0x0B
-#define CTL_REG_ERXRDPTL 0x0C
-#define CTL_REG_ERXRDPTH 0x0D
-#define CTL_REG_ERXWRPTL 0x0E
-#define CTL_REG_ERXWRPTH 0x0F
-#define CTL_REG_EDMASTL  0x10
-#define CTL_REG_EDMASTH  0x11
-#define CTL_REG_EDMANDL  0x12
-#define CTL_REG_EDMANDH  0x13
-#define CTL_REG_EDMADSTL 0x14
-#define CTL_REG_EDMADSTH 0x15
-#define CTL_REG_EDMACSL  0x16
-#define CTL_REG_EDMACSH  0x17
-/* these are common in all banks */
-#define CTL_REG_EIE	 0x1B
-#define CTL_REG_EIR	 0x1C
-#define CTL_REG_ESTAT	 0x1D
-#define CTL_REG_ECON2	 0x1E
-#define CTL_REG_ECON1	 0x1F
-
-/*
- * Control Registers in Bank 1
- */
-
-#define CTL_REG_EHT0	0x00
-#define CTL_REG_EHT1	0x01
-#define CTL_REG_EHT2	0x02
-#define CTL_REG_EHT3	0x03
-#define CTL_REG_EHT4	0x04
-#define CTL_REG_EHT5	0x05
-#define CTL_REG_EHT6	0x06
-#define CTL_REG_EHT7	0x07
-#define CTL_REG_EPMM0	0x08
-#define CTL_REG_EPMM1	0x09
-#define CTL_REG_EPMM2	0x0A
-#define CTL_REG_EPMM3	0x0B
-#define CTL_REG_EPMM4	0x0C
-#define CTL_REG_EPMM5	0x0D
-#define CTL_REG_EPMM6	0x0E
-#define CTL_REG_EPMM7	0x0F
-#define CTL_REG_EPMCSL	0x10
-#define CTL_REG_EPMCSH	0x11
-#define CTL_REG_EPMOL	0x14
-#define CTL_REG_EPMOH	0x15
-#define CTL_REG_EWOLIE	0x16
-#define CTL_REG_EWOLIR	0x17
-#define CTL_REG_ERXFCON 0x18
-#define CTL_REG_EPKTCNT 0x19
-
-/*
- * Control Registers in Bank 2
- */
-
-#define CTL_REG_MACON1	 0x00
-#define CTL_REG_MACON2	 0x01
-#define CTL_REG_MACON3	 0x02
-#define CTL_REG_MACON4	 0x03
-#define CTL_REG_MABBIPG  0x04
-#define CTL_REG_MAIPGL	 0x06
-#define CTL_REG_MAIPGH	 0x07
-#define CTL_REG_MACLCON1 0x08
-#define CTL_REG_MACLCON2 0x09
-#define CTL_REG_MAMXFLL  0x0A
-#define CTL_REG_MAMXFLH  0x0B
-#define CTL_REG_MAPHSUP  0x0D
-#define CTL_REG_MICON	 0x11
-#define CTL_REG_MICMD	 0x12
-#define CTL_REG_MIREGADR 0x14
-#define CTL_REG_MIWRL	 0x16
-#define CTL_REG_MIWRH	 0x17
-#define CTL_REG_MIRDL	 0x18
-#define CTL_REG_MIRDH	 0x19
-
-/*
- * Control Registers in Bank 3
- */
-
-#define CTL_REG_MAADR1	0x00
-#define CTL_REG_MAADR0	0x01
-#define CTL_REG_MAADR3	0x02
-#define CTL_REG_MAADR2	0x03
-#define CTL_REG_MAADR5	0x04
-#define CTL_REG_MAADR4	0x05
-#define CTL_REG_EBSTSD	0x06
-#define CTL_REG_EBSTCON 0x07
-#define CTL_REG_EBSTCSL 0x08
-#define CTL_REG_EBSTCSH 0x09
-#define CTL_REG_MISTAT	0x0A
-#define CTL_REG_EREVID	0x12
-#define CTL_REG_ECOCON	0x15
-#define CTL_REG_EFLOCON 0x17
-#define CTL_REG_EPAUSL	0x18
-#define CTL_REG_EPAUSH	0x19
-
-
-/*
- * PHY Register
- */
-
-#define PHY_REG_PHID1 0x02
-#define PHY_REG_PHID2 0x03
-/* taken from the Linux driver */
-#define PHY_REG_PHCON1 0x00
-#define PHY_REG_PHCON2 0x10
-#define PHY_REG_PHLCON 0x14
-
-/*
- * Receive Filter Register (ERXFCON) bits
- */
-
-#define ENC_RFR_UCEN  0x80
-#define ENC_RFR_ANDOR 0x40
-#define ENC_RFR_CRCEN 0x20
-#define ENC_RFR_PMEN  0x10
-#define ENC_RFR_MPEN  0x08
-#define ENC_RFR_HTEN  0x04
-#define ENC_RFR_MCEN  0x02
-#define ENC_RFR_BCEN  0x01
-
-/*
- * ECON1 Register Bits
- */
-
-#define ENC_ECON1_TXRST  0x80
-#define ENC_ECON1_RXRST  0x40
-#define ENC_ECON1_DMAST  0x20
-#define ENC_ECON1_CSUMEN 0x10
-#define ENC_ECON1_TXRTS  0x08
-#define ENC_ECON1_RXEN	 0x04
-#define ENC_ECON1_BSEL1  0x02
-#define ENC_ECON1_BSEL0  0x01
-
-/*
- * ECON2 Register Bits
- */
-#define ENC_ECON2_AUTOINC 0x80
-#define ENC_ECON2_PKTDEC  0x40
-#define ENC_ECON2_PWRSV   0x20
-#define ENC_ECON2_VRPS	  0x08
-
-/*
- * EIR Register Bits
- */
-#define ENC_EIR_PKTIF  0x40
-#define ENC_EIR_DMAIF  0x20
-#define ENC_EIR_LINKIF 0x10
-#define ENC_EIR_TXIF   0x08
-#define ENC_EIR_WOLIF  0x04
-#define ENC_EIR_TXERIF 0x02
-#define ENC_EIR_RXERIF 0x01
-
-/*
- * ESTAT Register Bits
- */
-
-#define ENC_ESTAT_INT	  0x80
-#define ENC_ESTAT_LATECOL 0x10
-#define ENC_ESTAT_RXBUSY  0x04
-#define ENC_ESTAT_TXABRT  0x02
-#define ENC_ESTAT_CLKRDY  0x01
-
-/*
- * EIE Register Bits
- */
-
-#define ENC_EIE_INTIE  0x80
-#define ENC_EIE_PKTIE  0x40
-#define ENC_EIE_DMAIE  0x20
-#define ENC_EIE_LINKIE 0x10
-#define ENC_EIE_TXIE   0x08
-#define ENC_EIE_WOLIE  0x04
-#define ENC_EIE_TXERIE 0x02
-#define ENC_EIE_RXERIE 0x01
-
-/*
- * MACON1 Register Bits
- */
-#define ENC_MACON1_LOOPBK  0x10
-#define ENC_MACON1_TXPAUS  0x08
-#define ENC_MACON1_RXPAUS  0x04
-#define ENC_MACON1_PASSALL 0x02
-#define ENC_MACON1_MARXEN  0x01
-
-
-/*
- * MACON2 Register Bits
- */
-#define ENC_MACON2_MARST   0x80
-#define ENC_MACON2_RNDRST  0x40
-#define ENC_MACON2_MARXRST 0x08
-#define ENC_MACON2_RFUNRST 0x04
-#define ENC_MACON2_MATXRST 0x02
-#define ENC_MACON2_TFUNRST 0x01
-
-/*
- * MACON3 Register Bits
- */
-#define ENC_MACON3_PADCFG2 0x80
-#define ENC_MACON3_PADCFG1 0x40
-#define ENC_MACON3_PADCFG0 0x20
-#define ENC_MACON3_TXCRCEN 0x10
-#define ENC_MACON3_PHDRLEN 0x08
-#define ENC_MACON3_HFRMEN  0x04
-#define ENC_MACON3_FRMLNEN 0x02
-#define ENC_MACON3_FULDPX  0x01
-
-/*
- * MICMD Register Bits
- */
-#define ENC_MICMD_MIISCAN 0x02
-#define ENC_MICMD_MIIRD   0x01
-
-/*
- * MISTAT Register Bits
- */
-#define ENC_MISTAT_NVALID 0x04
-#define ENC_MISTAT_SCAN   0x02
-#define ENC_MISTAT_BUSY   0x01
-
-/*
- * PHID1 and PHID2 values
- */
-#define ENC_PHID1_VALUE 0x0083
-#define ENC_PHID2_VALUE 0x1400
-#define ENC_PHID2_MASK	0xFC00
-
-
-#define ENC_SPI_SLAVE_CS 0x00010000	/* pin P1.16 */
-#define ENC_RESET	 0x00020000	/* pin P1.17 */
-
-#define FAILSAFE_VALUE 5000
-
-/*
- * Controller memory layout:
- *
- * 0x0000 - 0x17ff  6k bytes receive buffer
- * 0x1800 - 0x1fff  2k bytes transmit buffer
- */
-/* Use the lower memory for receiver buffer. See errata pt. 5 */
-#define ENC_RX_BUF_START 0x0000
-#define ENC_TX_BUF_START 0x1800
-/* taken from the Linux driver */
-#define ENC_RX_BUF_END   0x17ff
-#define ENC_TX_BUF_END   0x1fff
-
-/* maximum frame length */
-#define ENC_MAX_FRM_LEN 1518
-
-#define enc_enable() PUT32(IO1CLR, ENC_SPI_SLAVE_CS)
-#define enc_disable() PUT32(IO1SET, ENC_SPI_SLAVE_CS)
-#define enc_cfg_spi() spi_set_cfg(0, 0, 0); spi_set_clock(8);
-
-
-static unsigned char encReadReg (unsigned char regNo);
-static void encWriteReg (unsigned char regNo, unsigned char data);
-static void encWriteRegRetry (unsigned char regNo, unsigned char data, int c);
-static void encReadBuff (unsigned short length, unsigned char *pBuff);
-static void encWriteBuff (unsigned short length, unsigned char *pBuff);
-static void encBitSet (unsigned char regNo, unsigned char data);
-static void encBitClr (unsigned char regNo, unsigned char data);
-static void encReset (void);
-static void encInit (unsigned char *pEthAddr);
-static unsigned short phyRead (unsigned char addr);
-static void phyWrite(unsigned char, unsigned short);
-static void encPoll (void);
-static void encRx (void);
-
-#define m_nic_read(reg) encReadReg(reg)
-#define m_nic_write(reg, data) encWriteReg(reg, data)
-#define m_nic_write_retry(reg, data, count) encWriteRegRetry(reg, data, count)
-#define m_nic_read_data(len, buf) encReadBuff((len), (buf))
-#define m_nic_write_data(len, buf) encWriteBuff((len), (buf))
-
-/* bit field set */
-#define m_nic_bfs(reg, data) encBitSet(reg, data)
-
-/* bit field clear */
-#define m_nic_bfc(reg, data) encBitClr(reg, data)
-
-static unsigned char bank = 0;	/* current bank in enc28j60 */
-static unsigned char next_pointer_lsb;
-static unsigned char next_pointer_msb;
-
-static unsigned char buffer[ENC_MAX_FRM_LEN];
-static int rxResetCounter = 0;
-
-#define RX_RESET_COUNTER 1000;
-
-/*-----------------------------------------------------------------------------
- * Always returns 0
- */
-int eth_init (bd_t * bis)
-{
-	unsigned char estatVal;
-	uchar enetaddr[6];
-
-	/* configure GPIO */
-	(*((volatile unsigned long *) IO1DIR)) |= ENC_SPI_SLAVE_CS;
-	(*((volatile unsigned long *) IO1DIR)) |= ENC_RESET;
-
-	/* CS and RESET active low */
-	PUT32 (IO1SET, ENC_SPI_SLAVE_CS);
-	PUT32 (IO1SET, ENC_RESET);
-
-	spi_init ();
-
-	/* taken from the Linux driver - dangerous stuff here! */
-	/* Wait for CLKRDY to become set (i.e., check that we can communicate with
-	   the ENC) */
-	do
-	{
-		estatVal = m_nic_read(CTL_REG_ESTAT);
-	} while ((estatVal & 0x08) || (~estatVal & ENC_ESTAT_CLKRDY));
-
-	/* initialize controller */
-	encReset ();
-	eth_getenv_enetaddr("ethaddr", enetaddr);
-	encInit (enetaddr);
-
-	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* enable receive */
-
-	return 0;
-}
-
-int eth_send (volatile void *packet, int length)
-{
-	/* check frame length, etc. */
-	/* TODO: */
-
-	/* switch to bank 0 */
-	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
-
-	/* set EWRPT */
-	m_nic_write (CTL_REG_EWRPTL, (ENC_TX_BUF_START & 0xff));
-	m_nic_write (CTL_REG_EWRPTH, (ENC_TX_BUF_START >> 8));
-
-	/* set ETXND */
-	m_nic_write (CTL_REG_ETXNDL, (length + ENC_TX_BUF_START) & 0xFF);
-	m_nic_write (CTL_REG_ETXNDH, (length + ENC_TX_BUF_START) >> 8);
-
-	/* set ETXST */
-	m_nic_write (CTL_REG_ETXSTL, ENC_TX_BUF_START & 0xFF);
-	m_nic_write (CTL_REG_ETXSTH, ENC_TX_BUF_START >> 8);
-
-	/* write packet */
-	m_nic_write_data (length, (unsigned char *) packet);
-
-	/* taken from the Linux driver */
-	/* Verify that the internal transmit logic has not been altered by excessive
-	   collisions.  See Errata B4 12 and 14.
-	 */
-	if (m_nic_read(CTL_REG_EIR) & ENC_EIR_TXERIF) {
-		m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_TXRST);
-		m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_TXRST);
-	}
-	m_nic_bfc(CTL_REG_EIR, (ENC_EIR_TXERIF | ENC_EIR_TXIF));
-
-	/* set ECON1.TXRTS */
-	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_TXRTS);
-
-	return 0;
-}
-
-
-/*****************************************************************************
- * This function resets the receiver only. This function may be called from
- * interrupt-context.
- */
-static void encReceiverReset (void)
-{
-	unsigned char econ1;
-
-	econ1 = m_nic_read (CTL_REG_ECON1);
-	if ((econ1 & ENC_ECON1_RXRST) == 0) {
-		m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXRST);
-		rxResetCounter = RX_RESET_COUNTER;
-	}
-}
-
-/*****************************************************************************
- * receiver reset timer
- */
-static void encReceiverResetCallback (void)
-{
-	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_RXRST);
-	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* enable receive */
-}
-
-/*-----------------------------------------------------------------------------
- * Check for received packets. Call NetReceive for each packet. The return
- * value is ignored by the caller.
- */
-int eth_rx (void)
-{
-	if (rxResetCounter > 0 && --rxResetCounter == 0) {
-		encReceiverResetCallback ();
-	}
-
-	encPoll ();
-
-	return 0;
-}
-
-void eth_halt (void)
-{
-	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* disable receive */
-}
-
-/*****************************************************************************/
-
-static void encPoll (void)
-{
-	unsigned char eir_reg;
-	volatile unsigned char estat_reg;
-	unsigned char pkt_cnt;
-
-#ifdef CONFIG_USE_IRQ
-	/* clear global interrupt enable bit in enc28j60 */
-	m_nic_bfc (CTL_REG_EIE, ENC_EIE_INTIE);
-#endif
-	estat_reg = m_nic_read (CTL_REG_ESTAT);
-
-	eir_reg = m_nic_read (CTL_REG_EIR);
-
-	if (eir_reg & ENC_EIR_TXIF) {
-		/* clear TXIF bit in EIR */
-		m_nic_bfc (CTL_REG_EIR, ENC_EIR_TXIF);
-	}
-
-	/* We have to use pktcnt and not pktif bit, see errata pt. 6 */
-
-	/* move to bank 1 */
-	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL1);
-	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL0);
-
-	/* read pktcnt */
-	pkt_cnt = m_nic_read (CTL_REG_EPKTCNT);
-
-	if (pkt_cnt > 0) {
-		if ((eir_reg & ENC_EIR_PKTIF) == 0) {
-			/*printf("encPoll: pkt cnt > 0, but pktif not set\n"); */
-		}
-		encRx ();
-		/* clear PKTIF bit in EIR, this should not need to be done but it
-		   seems like we get problems if we do not */
-		m_nic_bfc (CTL_REG_EIR, ENC_EIR_PKTIF);
-	}
-
-	if (eir_reg & ENC_EIR_RXERIF) {
-		printf ("encPoll: rx error\n");
-		m_nic_bfc (CTL_REG_EIR, ENC_EIR_RXERIF);
-	}
-	if (eir_reg & ENC_EIR_TXERIF) {
-		printf ("encPoll: tx error\n");
-		m_nic_bfc (CTL_REG_EIR, ENC_EIR_TXERIF);
-	}
-
-#ifdef CONFIG_USE_IRQ
-	/* set global interrupt enable bit in enc28j60 */
-	m_nic_bfs (CTL_REG_EIE, ENC_EIE_INTIE);
-#endif
-}
-
-static void encRx (void)
-{
-	unsigned short pkt_len;
-	unsigned short copy_len;
-	unsigned short status;
-	unsigned char eir_reg;
-	unsigned char pkt_cnt = 0;
-	unsigned short rxbuf_rdpt;
-
-	/* switch to bank 0 */
-	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
-
-	m_nic_write (CTL_REG_ERDPTL, next_pointer_lsb);
-	m_nic_write (CTL_REG_ERDPTH, next_pointer_msb);
-
-	do {
-		m_nic_read_data (6, buffer);
-		next_pointer_lsb = buffer[0];
-		next_pointer_msb = buffer[1];
-		pkt_len = buffer[2];
-		pkt_len |= (unsigned short) buffer[3] << 8;
-		status = buffer[4];
-		status |= (unsigned short) buffer[5] << 8;
-
-		if (pkt_len <= ENC_MAX_FRM_LEN)
-			copy_len = pkt_len;
-		else
-			copy_len = 0;
-
-		if ((status & (1L << 7)) == 0) /* check Received Ok bit */
-			copy_len = 0;
-
-		/* taken from the Linux driver */
-		/* check if next pointer is resonable */
-		if ((((unsigned int)next_pointer_msb << 8) |
-			(unsigned int)next_pointer_lsb) >= ENC_TX_BUF_START)
-			copy_len = 0;
-
-		if (copy_len > 0) {
-			m_nic_read_data (copy_len, buffer);
-		}
-
-		/* advance read pointer to next pointer */
-		m_nic_write (CTL_REG_ERDPTL, next_pointer_lsb);
-		m_nic_write (CTL_REG_ERDPTH, next_pointer_msb);
-
-		/* decrease packet counter */
-		m_nic_bfs (CTL_REG_ECON2, ENC_ECON2_PKTDEC);
-
-		/* taken from the Linux driver */
-		/* Only odd values should be written to ERXRDPTL,
-		 * see errata B4 pt.13
-		 */
-		rxbuf_rdpt = (next_pointer_msb << 8 | next_pointer_lsb) - 1;
-		if ((rxbuf_rdpt < (m_nic_read(CTL_REG_ERXSTH) << 8 |
-				m_nic_read(CTL_REG_ERXSTL))) || (rxbuf_rdpt >
-				(m_nic_read(CTL_REG_ERXNDH) << 8 |
-				m_nic_read(CTL_REG_ERXNDL)))) {
-			m_nic_write(CTL_REG_ERXRDPTL, m_nic_read(CTL_REG_ERXNDL));
-			m_nic_write(CTL_REG_ERXRDPTH, m_nic_read(CTL_REG_ERXNDH));
-		} else {
-			m_nic_write(CTL_REG_ERXRDPTL, rxbuf_rdpt & 0xFF);
-			m_nic_write(CTL_REG_ERXRDPTH, rxbuf_rdpt >> 8);
-		}
-
-		/* move to bank 1 */
-		m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL1);
-		m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL0);
-
-		/* read pktcnt */
-		pkt_cnt = m_nic_read (CTL_REG_EPKTCNT);
-
-		/* switch to bank 0 */
-		m_nic_bfc (CTL_REG_ECON1,
-			   (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
-
-		if (copy_len == 0) {
-			eir_reg = m_nic_read (CTL_REG_EIR);
-			encReceiverReset ();
-			printf ("eth_rx: copy_len=0\n");
-			continue;
-		}
-
-		NetReceive ((unsigned char *) buffer, pkt_len);
-
-		eir_reg = m_nic_read (CTL_REG_EIR);
-	} while (pkt_cnt);	/* Use EPKTCNT not EIR.PKTIF flag, see errata pt. 6 */
-}
-
-static void encWriteReg (unsigned char regNo, unsigned char data)
-{
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0x40 | regNo);	/* write in regNo */
-	spi_write (data);
-
-	enc_disable ();
-	enc_enable ();
-
-	spi_write (0x1f);	/* write reg 0x1f */
-
-	enc_disable ();
-	spi_unlock ();
-}
-
-static void encWriteRegRetry (unsigned char regNo, unsigned char data, int c)
-{
-	unsigned char readback;
-	int i;
-
-	spi_lock ();
-
-	for (i = 0; i < c; i++) {
-		enc_cfg_spi ();
-		enc_enable ();
-
-		spi_write (0x40 | regNo);	/* write in regNo */
-		spi_write (data);
-
-		enc_disable ();
-		enc_enable ();
-
-		spi_write (0x1f);	/* write reg 0x1f */
-
-		enc_disable ();
-
-		spi_unlock ();	/* we must unlock spi first */
-
-		readback = encReadReg (regNo);
-
-		spi_lock ();
-
-		if (readback == data)
-			break;
-	}
-	spi_unlock ();
-
-	if (i == c) {
-		printf ("enc28j60: write reg %d failed\n", regNo);
-	}
-}
-
-static unsigned char encReadReg (unsigned char regNo)
-{
-	unsigned char rxByte;
-
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0x1f);	/* read reg 0x1f */
-
-	bank = spi_read () & 0x3;
-
-	enc_disable ();
-	enc_enable ();
-
-	spi_write (regNo);
-	rxByte = spi_read ();
-
-	/* check if MAC or MII register */
-	if (((bank == 2) && (regNo <= 0x1a)) ||
-	    ((bank == 3) && (regNo <= 0x05 || regNo == 0x0a))) {
-		/* ignore first byte and read another byte */
-		rxByte = spi_read ();
-	}
-
-	enc_disable ();
-	spi_unlock ();
-
-	return rxByte;
-}
-
-static void encReadBuff (unsigned short length, unsigned char *pBuff)
-{
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0x20 | 0x1a);	/* read buffer memory */
-
-	while (length--) {
-		if (pBuff != NULL)
-			*pBuff++ = spi_read ();
-		else
-			spi_write (0);
-	}
-
-	enc_disable ();
-	spi_unlock ();
-}
-
-static void encWriteBuff (unsigned short length, unsigned char *pBuff)
-{
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0x60 | 0x1a);	/* write buffer memory */
-
-	spi_write (0x00);	/* control byte */
-
-	while (length--)
-		spi_write (*pBuff++);
-
-	enc_disable ();
-	spi_unlock ();
-}
-
-static void encBitSet (unsigned char regNo, unsigned char data)
-{
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0x80 | regNo);	/* bit field set */
-	spi_write (data);
-
-	enc_disable ();
-	spi_unlock ();
-}
-
-static void encBitClr (unsigned char regNo, unsigned char data)
-{
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0xA0 | regNo);	/* bit field clear */
-	spi_write (data);
-
-	enc_disable ();
-	spi_unlock ();
-}
-
-static void encReset (void)
-{
-	spi_lock ();
-	enc_cfg_spi ();
-	enc_enable ();
-
-	spi_write (0xff);	/* soft reset */
-
-	enc_disable ();
-	spi_unlock ();
-
-	/* sleep 1 ms. See errata pt. 2 */
-	udelay (1000);
-}
-
-static void encInit (unsigned char *pEthAddr)
-{
-	unsigned short phid1 = 0;
-	unsigned short phid2 = 0;
-
-	/* switch to bank 0 */
-	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
-
-	/*
-	 * Setup the buffer space. The reset values are valid for the
-	 * other pointers.
-	 */
-	/* We shall not write to ERXST, see errata pt. 5. Instead we
-	   have to make sure that ENC_RX_BUS_START is 0. */
-	m_nic_write_retry (CTL_REG_ERXSTL, (ENC_RX_BUF_START & 0xFF), 1);
-	m_nic_write_retry (CTL_REG_ERXSTH, (ENC_RX_BUF_START >> 8), 1);
-
-	/* taken from the Linux driver */
-	m_nic_write_retry (CTL_REG_ERXNDL, (ENC_RX_BUF_END & 0xFF), 1);
-	m_nic_write_retry (CTL_REG_ERXNDH, (ENC_RX_BUF_END >> 8), 1);
-
-	m_nic_write_retry (CTL_REG_ERDPTL, (ENC_RX_BUF_START & 0xFF), 1);
-	m_nic_write_retry (CTL_REG_ERDPTH, (ENC_RX_BUF_START >> 8), 1);
-
-	next_pointer_lsb = (ENC_RX_BUF_START & 0xFF);
-	next_pointer_msb = (ENC_RX_BUF_START >> 8);
-
-	/* verify identification */
-	phid1 = phyRead (PHY_REG_PHID1);
-	phid2 = phyRead (PHY_REG_PHID2);
-
-	if (phid1 != ENC_PHID1_VALUE
-	    || (phid2 & ENC_PHID2_MASK) != ENC_PHID2_VALUE) {
-		printf ("ERROR: failed to identify controller\n");
-		printf ("phid1 = %x, phid2 = %x\n",
-			phid1, (phid2 & ENC_PHID2_MASK));
-		printf ("should be phid1 = %x, phid2 = %x\n",
-			ENC_PHID1_VALUE, ENC_PHID2_VALUE);
-	}
-
-	/*
-	 * --- MAC Initialization ---
-	 */
-
-	/* Pull MAC out of Reset */
-
-	/* switch to bank 2 */
-	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL0);
-	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL1);
-
-	/* enable MAC to receive frames */
-	/* added some bits from the Linux driver */
-	m_nic_write_retry (CTL_REG_MACON1
-		,(ENC_MACON1_MARXEN | ENC_MACON1_TXPAUS | ENC_MACON1_RXPAUS)
-		,10);
-
-	/* configure pad, tx-crc and duplex */
-	/* added a bit from the Linux driver */
-	m_nic_write_retry (CTL_REG_MACON3
-		,(ENC_MACON3_PADCFG0 | ENC_MACON3_TXCRCEN | ENC_MACON3_FRMLNEN)
-		,10);
-
-	/* added 4 new lines from the Linux driver */
-	/* Allow infinite deferals if the medium is continously busy */
-	m_nic_write_retry(CTL_REG_MACON4, (1<<6) /*ENC_MACON4_DEFER*/, 10);
-
-	/* Late collisions occur beyond 63 bytes */
-	m_nic_write_retry(CTL_REG_MACLCON2, 63, 10);
-
-	/* Set (low byte) Non-Back-to_Back Inter-Packet Gap. Recommended 0x12 */
-	m_nic_write_retry(CTL_REG_MAIPGL, 0x12, 10);
-
-	/*
-	* Set (high byte) Non-Back-to_Back Inter-Packet Gap. Recommended
-	* 0x0c for half-duplex. Nothing for full-duplex
-	*/
-	m_nic_write_retry(CTL_REG_MAIPGH, 0x0C, 10);
-
-	/* set maximum frame length */
-	m_nic_write_retry (CTL_REG_MAMXFLL, (ENC_MAX_FRM_LEN & 0xff), 10);
-	m_nic_write_retry (CTL_REG_MAMXFLH, (ENC_MAX_FRM_LEN >> 8), 10);
-
-	/*
-	 * Set MAC back-to-back inter-packet gap. Recommended 0x12 for half duplex
-	 * and 0x15 for full duplex.
-	 */
-	m_nic_write_retry (CTL_REG_MABBIPG, 0x12, 10);
-
-	/* set MAC address */
-
-	/* switch to bank 3 */
-	m_nic_bfs (CTL_REG_ECON1, (ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1));
-
-	m_nic_write_retry (CTL_REG_MAADR0, pEthAddr[5], 1);
-	m_nic_write_retry (CTL_REG_MAADR1, pEthAddr[4], 1);
-	m_nic_write_retry (CTL_REG_MAADR2, pEthAddr[3], 1);
-	m_nic_write_retry (CTL_REG_MAADR3, pEthAddr[2], 1);
-	m_nic_write_retry (CTL_REG_MAADR4, pEthAddr[1], 1);
-	m_nic_write_retry (CTL_REG_MAADR5, pEthAddr[0], 1);
-
-	/*
-	* PHY Initialization taken from the Linux driver
-	 */
-
-	/* Prevent automatic loopback of data beeing transmitted by setting
-	   ENC_PHCON2_HDLDIS */
-	phyWrite(PHY_REG_PHCON2, (1<<8));
-
-	/* LEDs configuration
-	 * LEDA: LACFG = 0100 -> display link status
-	 * LEDB: LBCFG = 0111 -> display TX & RX activity
-	 * STRCH = 1 -> LED pulses
-	 */
-	phyWrite(PHY_REG_PHLCON, 0x0472);
-
-	/* Reset PDPXMD-bit => half duplex */
-	phyWrite(PHY_REG_PHCON1, 0);
-
-	/*
-	 * Receive settings
-	 */
-
-#ifdef CONFIG_USE_IRQ
-	/* enable interrupts */
-	m_nic_bfs (CTL_REG_EIE, ENC_EIE_PKTIE);
-	m_nic_bfs (CTL_REG_EIE, ENC_EIE_TXIE);
-	m_nic_bfs (CTL_REG_EIE, ENC_EIE_RXERIE);
-	m_nic_bfs (CTL_REG_EIE, ENC_EIE_TXERIE);
-	m_nic_bfs (CTL_REG_EIE, ENC_EIE_INTIE);
-#endif
-}
-
-/*****************************************************************************
- *
- * Description:
- *    Read PHY registers.
- *
- *    NOTE! This function will change to Bank 2.
- *
- * Params:
- *    [in] addr address of the register to read
- *
- * Returns:
- *    The value in the register
- */
-static unsigned short phyRead (unsigned char addr)
-{
-	unsigned short ret = 0;
-
-	/* move to bank 2 */
-	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL0);
-	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL1);
-
-	/* write address to MIREGADR */
-	m_nic_write (CTL_REG_MIREGADR, addr);
-
-	/* set MICMD.MIIRD */
-	m_nic_write (CTL_REG_MICMD, ENC_MICMD_MIIRD);
-
-	/* taken from the Linux driver */
-	/* move to bank 3 */
-	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL0);
-	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
-
-	/* poll MISTAT.BUSY bit until operation is complete */
-	while ((m_nic_read (CTL_REG_MISTAT) & ENC_MISTAT_BUSY) != 0) {
-		static int cnt = 0;
-
-		if (cnt++ >= 1000) {
-			/* GJ - this seems extremely dangerous! */
-			/* printf("#"); */
-			cnt = 0;
-		}
-	}
-
-	/* taken from the Linux driver */
-	/* move to bank 2 */
-	m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_BSEL0);
-	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
-
-	/* clear MICMD.MIIRD */
-	m_nic_write (CTL_REG_MICMD, 0);
-
-	ret = (m_nic_read (CTL_REG_MIRDH) << 8);
-	ret |= (m_nic_read (CTL_REG_MIRDL) & 0xFF);
-
-	return ret;
-}
-
-/*****************************************************************************
- *
- * Taken from the Linux driver.
- * Description:
- * Write PHY registers.
- *
- * NOTE! This function will change to Bank 3.
- *
- * Params:
- * [in] addr address of the register to write to
- * [in] data to be written
- *
- * Returns:
- *    None
- */
-static void phyWrite(unsigned char addr, unsigned short data)
-{
-	/* move to bank 2 */
-	m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_BSEL0);
-	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
-
-	/* write address to MIREGADR */
-	m_nic_write(CTL_REG_MIREGADR, addr);
-
-	m_nic_write(CTL_REG_MIWRL, data & 0xff);
-	m_nic_write(CTL_REG_MIWRH, data >> 8);
-
-	/* move to bank 3 */
-	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL0);
-	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
-
-	/* poll MISTAT.BUSY bit until operation is complete */
-	while((m_nic_read(CTL_REG_MISTAT) & ENC_MISTAT_BUSY) != 0) {
-		static int cnt = 0;
-
-		if(cnt++ >= 1000) {
-			cnt = 0;
-		}
-	}
-}
diff --git a/drivers/net/enc28j60_lpc2292.c b/drivers/net/enc28j60_lpc2292.c
new file mode 100644
index 0000000..bf95052
--- /dev/null
+++ b/drivers/net/enc28j60_lpc2292.c
@@ -0,0 +1,983 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#warning This driver is depreciated. Please update to new SPI framework enc28j60 driver
+#include <config.h>
+#include <common.h>
+#include <net.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/spi.h>
+
+/*
+ * Control Registers in Bank 0
+ */
+
+#define CTL_REG_ERDPTL	 0x00
+#define CTL_REG_ERDPTH	 0x01
+#define CTL_REG_EWRPTL	 0x02
+#define CTL_REG_EWRPTH	 0x03
+#define CTL_REG_ETXSTL	 0x04
+#define CTL_REG_ETXSTH	 0x05
+#define CTL_REG_ETXNDL	 0x06
+#define CTL_REG_ETXNDH	 0x07
+#define CTL_REG_ERXSTL	 0x08
+#define CTL_REG_ERXSTH	 0x09
+#define CTL_REG_ERXNDL	 0x0A
+#define CTL_REG_ERXNDH	 0x0B
+#define CTL_REG_ERXRDPTL 0x0C
+#define CTL_REG_ERXRDPTH 0x0D
+#define CTL_REG_ERXWRPTL 0x0E
+#define CTL_REG_ERXWRPTH 0x0F
+#define CTL_REG_EDMASTL  0x10
+#define CTL_REG_EDMASTH  0x11
+#define CTL_REG_EDMANDL  0x12
+#define CTL_REG_EDMANDH  0x13
+#define CTL_REG_EDMADSTL 0x14
+#define CTL_REG_EDMADSTH 0x15
+#define CTL_REG_EDMACSL  0x16
+#define CTL_REG_EDMACSH  0x17
+/* these are common in all banks */
+#define CTL_REG_EIE	 0x1B
+#define CTL_REG_EIR	 0x1C
+#define CTL_REG_ESTAT	 0x1D
+#define CTL_REG_ECON2	 0x1E
+#define CTL_REG_ECON1	 0x1F
+
+/*
+ * Control Registers in Bank 1
+ */
+
+#define CTL_REG_EHT0	0x00
+#define CTL_REG_EHT1	0x01
+#define CTL_REG_EHT2	0x02
+#define CTL_REG_EHT3	0x03
+#define CTL_REG_EHT4	0x04
+#define CTL_REG_EHT5	0x05
+#define CTL_REG_EHT6	0x06
+#define CTL_REG_EHT7	0x07
+#define CTL_REG_EPMM0	0x08
+#define CTL_REG_EPMM1	0x09
+#define CTL_REG_EPMM2	0x0A
+#define CTL_REG_EPMM3	0x0B
+#define CTL_REG_EPMM4	0x0C
+#define CTL_REG_EPMM5	0x0D
+#define CTL_REG_EPMM6	0x0E
+#define CTL_REG_EPMM7	0x0F
+#define CTL_REG_EPMCSL	0x10
+#define CTL_REG_EPMCSH	0x11
+#define CTL_REG_EPMOL	0x14
+#define CTL_REG_EPMOH	0x15
+#define CTL_REG_EWOLIE	0x16
+#define CTL_REG_EWOLIR	0x17
+#define CTL_REG_ERXFCON 0x18
+#define CTL_REG_EPKTCNT 0x19
+
+/*
+ * Control Registers in Bank 2
+ */
+
+#define CTL_REG_MACON1	 0x00
+#define CTL_REG_MACON2	 0x01
+#define CTL_REG_MACON3	 0x02
+#define CTL_REG_MACON4	 0x03
+#define CTL_REG_MABBIPG  0x04
+#define CTL_REG_MAIPGL	 0x06
+#define CTL_REG_MAIPGH	 0x07
+#define CTL_REG_MACLCON1 0x08
+#define CTL_REG_MACLCON2 0x09
+#define CTL_REG_MAMXFLL  0x0A
+#define CTL_REG_MAMXFLH  0x0B
+#define CTL_REG_MAPHSUP  0x0D
+#define CTL_REG_MICON	 0x11
+#define CTL_REG_MICMD	 0x12
+#define CTL_REG_MIREGADR 0x14
+#define CTL_REG_MIWRL	 0x16
+#define CTL_REG_MIWRH	 0x17
+#define CTL_REG_MIRDL	 0x18
+#define CTL_REG_MIRDH	 0x19
+
+/*
+ * Control Registers in Bank 3
+ */
+
+#define CTL_REG_MAADR1	0x00
+#define CTL_REG_MAADR0	0x01
+#define CTL_REG_MAADR3	0x02
+#define CTL_REG_MAADR2	0x03
+#define CTL_REG_MAADR5	0x04
+#define CTL_REG_MAADR4	0x05
+#define CTL_REG_EBSTSD	0x06
+#define CTL_REG_EBSTCON 0x07
+#define CTL_REG_EBSTCSL 0x08
+#define CTL_REG_EBSTCSH 0x09
+#define CTL_REG_MISTAT	0x0A
+#define CTL_REG_EREVID	0x12
+#define CTL_REG_ECOCON	0x15
+#define CTL_REG_EFLOCON 0x17
+#define CTL_REG_EPAUSL	0x18
+#define CTL_REG_EPAUSH	0x19
+
+
+/*
+ * PHY Register
+ */
+
+#define PHY_REG_PHID1 0x02
+#define PHY_REG_PHID2 0x03
+/* taken from the Linux driver */
+#define PHY_REG_PHCON1 0x00
+#define PHY_REG_PHCON2 0x10
+#define PHY_REG_PHLCON 0x14
+
+/*
+ * Receive Filter Register (ERXFCON) bits
+ */
+
+#define ENC_RFR_UCEN  0x80
+#define ENC_RFR_ANDOR 0x40
+#define ENC_RFR_CRCEN 0x20
+#define ENC_RFR_PMEN  0x10
+#define ENC_RFR_MPEN  0x08
+#define ENC_RFR_HTEN  0x04
+#define ENC_RFR_MCEN  0x02
+#define ENC_RFR_BCEN  0x01
+
+/*
+ * ECON1 Register Bits
+ */
+
+#define ENC_ECON1_TXRST  0x80
+#define ENC_ECON1_RXRST  0x40
+#define ENC_ECON1_DMAST  0x20
+#define ENC_ECON1_CSUMEN 0x10
+#define ENC_ECON1_TXRTS  0x08
+#define ENC_ECON1_RXEN	 0x04
+#define ENC_ECON1_BSEL1  0x02
+#define ENC_ECON1_BSEL0  0x01
+
+/*
+ * ECON2 Register Bits
+ */
+#define ENC_ECON2_AUTOINC 0x80
+#define ENC_ECON2_PKTDEC  0x40
+#define ENC_ECON2_PWRSV   0x20
+#define ENC_ECON2_VRPS	  0x08
+
+/*
+ * EIR Register Bits
+ */
+#define ENC_EIR_PKTIF  0x40
+#define ENC_EIR_DMAIF  0x20
+#define ENC_EIR_LINKIF 0x10
+#define ENC_EIR_TXIF   0x08
+#define ENC_EIR_WOLIF  0x04
+#define ENC_EIR_TXERIF 0x02
+#define ENC_EIR_RXERIF 0x01
+
+/*
+ * ESTAT Register Bits
+ */
+
+#define ENC_ESTAT_INT	  0x80
+#define ENC_ESTAT_LATECOL 0x10
+#define ENC_ESTAT_RXBUSY  0x04
+#define ENC_ESTAT_TXABRT  0x02
+#define ENC_ESTAT_CLKRDY  0x01
+
+/*
+ * EIE Register Bits
+ */
+
+#define ENC_EIE_INTIE  0x80
+#define ENC_EIE_PKTIE  0x40
+#define ENC_EIE_DMAIE  0x20
+#define ENC_EIE_LINKIE 0x10
+#define ENC_EIE_TXIE   0x08
+#define ENC_EIE_WOLIE  0x04
+#define ENC_EIE_TXERIE 0x02
+#define ENC_EIE_RXERIE 0x01
+
+/*
+ * MACON1 Register Bits
+ */
+#define ENC_MACON1_LOOPBK  0x10
+#define ENC_MACON1_TXPAUS  0x08
+#define ENC_MACON1_RXPAUS  0x04
+#define ENC_MACON1_PASSALL 0x02
+#define ENC_MACON1_MARXEN  0x01
+
+
+/*
+ * MACON2 Register Bits
+ */
+#define ENC_MACON2_MARST   0x80
+#define ENC_MACON2_RNDRST  0x40
+#define ENC_MACON2_MARXRST 0x08
+#define ENC_MACON2_RFUNRST 0x04
+#define ENC_MACON2_MATXRST 0x02
+#define ENC_MACON2_TFUNRST 0x01
+
+/*
+ * MACON3 Register Bits
+ */
+#define ENC_MACON3_PADCFG2 0x80
+#define ENC_MACON3_PADCFG1 0x40
+#define ENC_MACON3_PADCFG0 0x20
+#define ENC_MACON3_TXCRCEN 0x10
+#define ENC_MACON3_PHDRLEN 0x08
+#define ENC_MACON3_HFRMEN  0x04
+#define ENC_MACON3_FRMLNEN 0x02
+#define ENC_MACON3_FULDPX  0x01
+
+/*
+ * MICMD Register Bits
+ */
+#define ENC_MICMD_MIISCAN 0x02
+#define ENC_MICMD_MIIRD   0x01
+
+/*
+ * MISTAT Register Bits
+ */
+#define ENC_MISTAT_NVALID 0x04
+#define ENC_MISTAT_SCAN   0x02
+#define ENC_MISTAT_BUSY   0x01
+
+/*
+ * PHID1 and PHID2 values
+ */
+#define ENC_PHID1_VALUE 0x0083
+#define ENC_PHID2_VALUE 0x1400
+#define ENC_PHID2_MASK	0xFC00
+
+
+#define ENC_SPI_SLAVE_CS 0x00010000	/* pin P1.16 */
+#define ENC_RESET	 0x00020000	/* pin P1.17 */
+
+#define FAILSAFE_VALUE 5000
+
+/*
+ * Controller memory layout:
+ *
+ * 0x0000 - 0x17ff  6k bytes receive buffer
+ * 0x1800 - 0x1fff  2k bytes transmit buffer
+ */
+/* Use the lower memory for receiver buffer. See errata pt. 5 */
+#define ENC_RX_BUF_START 0x0000
+#define ENC_TX_BUF_START 0x1800
+/* taken from the Linux driver */
+#define ENC_RX_BUF_END   0x17ff
+#define ENC_TX_BUF_END   0x1fff
+
+/* maximum frame length */
+#define ENC_MAX_FRM_LEN 1518
+
+#define enc_enable() PUT32(IO1CLR, ENC_SPI_SLAVE_CS)
+#define enc_disable() PUT32(IO1SET, ENC_SPI_SLAVE_CS)
+#define enc_cfg_spi() spi_set_cfg(0, 0, 0); spi_set_clock(8);
+
+
+static unsigned char encReadReg (unsigned char regNo);
+static void encWriteReg (unsigned char regNo, unsigned char data);
+static void encWriteRegRetry (unsigned char regNo, unsigned char data, int c);
+static void encReadBuff (unsigned short length, unsigned char *pBuff);
+static void encWriteBuff (unsigned short length, unsigned char *pBuff);
+static void encBitSet (unsigned char regNo, unsigned char data);
+static void encBitClr (unsigned char regNo, unsigned char data);
+static void encReset (void);
+static void encInit (unsigned char *pEthAddr);
+static unsigned short phyRead (unsigned char addr);
+static void phyWrite(unsigned char, unsigned short);
+static void encPoll (void);
+static void encRx (void);
+
+#define m_nic_read(reg) encReadReg(reg)
+#define m_nic_write(reg, data) encWriteReg(reg, data)
+#define m_nic_write_retry(reg, data, count) encWriteRegRetry(reg, data, count)
+#define m_nic_read_data(len, buf) encReadBuff((len), (buf))
+#define m_nic_write_data(len, buf) encWriteBuff((len), (buf))
+
+/* bit field set */
+#define m_nic_bfs(reg, data) encBitSet(reg, data)
+
+/* bit field clear */
+#define m_nic_bfc(reg, data) encBitClr(reg, data)
+
+static unsigned char bank = 0;	/* current bank in enc28j60 */
+static unsigned char next_pointer_lsb;
+static unsigned char next_pointer_msb;
+
+static unsigned char buffer[ENC_MAX_FRM_LEN];
+static int rxResetCounter = 0;
+
+#define RX_RESET_COUNTER 1000;
+
+/*-----------------------------------------------------------------------------
+ * Always returns 0
+ */
+int eth_init (bd_t * bis)
+{
+	unsigned char estatVal;
+	uchar enetaddr[6];
+
+	/* configure GPIO */
+	(*((volatile unsigned long *) IO1DIR)) |= ENC_SPI_SLAVE_CS;
+	(*((volatile unsigned long *) IO1DIR)) |= ENC_RESET;
+
+	/* CS and RESET active low */
+	PUT32 (IO1SET, ENC_SPI_SLAVE_CS);
+	PUT32 (IO1SET, ENC_RESET);
+
+	spi_init ();
+
+	/* taken from the Linux driver - dangerous stuff here! */
+	/* Wait for CLKRDY to become set (i.e., check that we can communicate with
+	   the ENC) */
+	do
+	{
+		estatVal = m_nic_read(CTL_REG_ESTAT);
+	} while ((estatVal & 0x08) || (~estatVal & ENC_ESTAT_CLKRDY));
+
+	/* initialize controller */
+	encReset ();
+	eth_getenv_enetaddr("ethaddr", enetaddr);
+	encInit (enetaddr);
+
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* enable receive */
+
+	return 0;
+}
+
+int eth_send (volatile void *packet, int length)
+{
+	/* check frame length, etc. */
+	/* TODO: */
+
+	/* switch to bank 0 */
+	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+	/* set EWRPT */
+	m_nic_write (CTL_REG_EWRPTL, (ENC_TX_BUF_START & 0xff));
+	m_nic_write (CTL_REG_EWRPTH, (ENC_TX_BUF_START >> 8));
+
+	/* set ETXND */
+	m_nic_write (CTL_REG_ETXNDL, (length + ENC_TX_BUF_START) & 0xFF);
+	m_nic_write (CTL_REG_ETXNDH, (length + ENC_TX_BUF_START) >> 8);
+
+	/* set ETXST */
+	m_nic_write (CTL_REG_ETXSTL, ENC_TX_BUF_START & 0xFF);
+	m_nic_write (CTL_REG_ETXSTH, ENC_TX_BUF_START >> 8);
+
+	/* write packet */
+	m_nic_write_data (length, (unsigned char *) packet);
+
+	/* taken from the Linux driver */
+	/* Verify that the internal transmit logic has not been altered by excessive
+	   collisions.  See Errata B4 12 and 14.
+	 */
+	if (m_nic_read(CTL_REG_EIR) & ENC_EIR_TXERIF) {
+		m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_TXRST);
+		m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_TXRST);
+	}
+	m_nic_bfc(CTL_REG_EIR, (ENC_EIR_TXERIF | ENC_EIR_TXIF));
+
+	/* set ECON1.TXRTS */
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_TXRTS);
+
+	return 0;
+}
+
+
+/*****************************************************************************
+ * This function resets the receiver only. This function may be called from
+ * interrupt-context.
+ */
+static void encReceiverReset (void)
+{
+	unsigned char econ1;
+
+	econ1 = m_nic_read (CTL_REG_ECON1);
+	if ((econ1 & ENC_ECON1_RXRST) == 0) {
+		m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXRST);
+		rxResetCounter = RX_RESET_COUNTER;
+	}
+}
+
+/*****************************************************************************
+ * receiver reset timer
+ */
+static void encReceiverResetCallback (void)
+{
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_RXRST);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* enable receive */
+}
+
+/*-----------------------------------------------------------------------------
+ * Check for received packets. Call NetReceive for each packet. The return
+ * value is ignored by the caller.
+ */
+int eth_rx (void)
+{
+	if (rxResetCounter > 0 && --rxResetCounter == 0) {
+		encReceiverResetCallback ();
+	}
+
+	encPoll ();
+
+	return 0;
+}
+
+void eth_halt (void)
+{
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* disable receive */
+}
+
+/*****************************************************************************/
+
+static void encPoll (void)
+{
+	unsigned char eir_reg;
+	volatile unsigned char estat_reg;
+	unsigned char pkt_cnt;
+
+#ifdef CONFIG_USE_IRQ
+	/* clear global interrupt enable bit in enc28j60 */
+	m_nic_bfc (CTL_REG_EIE, ENC_EIE_INTIE);
+#endif
+	estat_reg = m_nic_read (CTL_REG_ESTAT);
+
+	eir_reg = m_nic_read (CTL_REG_EIR);
+
+	if (eir_reg & ENC_EIR_TXIF) {
+		/* clear TXIF bit in EIR */
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_TXIF);
+	}
+
+	/* We have to use pktcnt and not pktif bit, see errata pt. 6 */
+
+	/* move to bank 1 */
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+
+	/* read pktcnt */
+	pkt_cnt = m_nic_read (CTL_REG_EPKTCNT);
+
+	if (pkt_cnt > 0) {
+		if ((eir_reg & ENC_EIR_PKTIF) == 0) {
+			/*printf("encPoll: pkt cnt > 0, but pktif not set\n"); */
+		}
+		encRx ();
+		/* clear PKTIF bit in EIR, this should not need to be done but it
+		   seems like we get problems if we do not */
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_PKTIF);
+	}
+
+	if (eir_reg & ENC_EIR_RXERIF) {
+		printf ("encPoll: rx error\n");
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_RXERIF);
+	}
+	if (eir_reg & ENC_EIR_TXERIF) {
+		printf ("encPoll: tx error\n");
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_TXERIF);
+	}
+
+#ifdef CONFIG_USE_IRQ
+	/* set global interrupt enable bit in enc28j60 */
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_INTIE);
+#endif
+}
+
+static void encRx (void)
+{
+	unsigned short pkt_len;
+	unsigned short copy_len;
+	unsigned short status;
+	unsigned char eir_reg;
+	unsigned char pkt_cnt = 0;
+	unsigned short rxbuf_rdpt;
+
+	/* switch to bank 0 */
+	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+	m_nic_write (CTL_REG_ERDPTL, next_pointer_lsb);
+	m_nic_write (CTL_REG_ERDPTH, next_pointer_msb);
+
+	do {
+		m_nic_read_data (6, buffer);
+		next_pointer_lsb = buffer[0];
+		next_pointer_msb = buffer[1];
+		pkt_len = buffer[2];
+		pkt_len |= (unsigned short) buffer[3] << 8;
+		status = buffer[4];
+		status |= (unsigned short) buffer[5] << 8;
+
+		if (pkt_len <= ENC_MAX_FRM_LEN)
+			copy_len = pkt_len;
+		else
+			copy_len = 0;
+
+		if ((status & (1L << 7)) == 0) /* check Received Ok bit */
+			copy_len = 0;
+
+		/* taken from the Linux driver */
+		/* check if next pointer is resonable */
+		if ((((unsigned int)next_pointer_msb << 8) |
+			(unsigned int)next_pointer_lsb) >= ENC_TX_BUF_START)
+			copy_len = 0;
+
+		if (copy_len > 0) {
+			m_nic_read_data (copy_len, buffer);
+		}
+
+		/* advance read pointer to next pointer */
+		m_nic_write (CTL_REG_ERDPTL, next_pointer_lsb);
+		m_nic_write (CTL_REG_ERDPTH, next_pointer_msb);
+
+		/* decrease packet counter */
+		m_nic_bfs (CTL_REG_ECON2, ENC_ECON2_PKTDEC);
+
+		/* taken from the Linux driver */
+		/* Only odd values should be written to ERXRDPTL,
+		 * see errata B4 pt.13
+		 */
+		rxbuf_rdpt = (next_pointer_msb << 8 | next_pointer_lsb) - 1;
+		if ((rxbuf_rdpt < (m_nic_read(CTL_REG_ERXSTH) << 8 |
+				m_nic_read(CTL_REG_ERXSTL))) || (rxbuf_rdpt >
+				(m_nic_read(CTL_REG_ERXNDH) << 8 |
+				m_nic_read(CTL_REG_ERXNDL)))) {
+			m_nic_write(CTL_REG_ERXRDPTL, m_nic_read(CTL_REG_ERXNDL));
+			m_nic_write(CTL_REG_ERXRDPTH, m_nic_read(CTL_REG_ERXNDH));
+		} else {
+			m_nic_write(CTL_REG_ERXRDPTL, rxbuf_rdpt & 0xFF);
+			m_nic_write(CTL_REG_ERXRDPTH, rxbuf_rdpt >> 8);
+		}
+
+		/* move to bank 1 */
+		m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+		m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+
+		/* read pktcnt */
+		pkt_cnt = m_nic_read (CTL_REG_EPKTCNT);
+
+		/* switch to bank 0 */
+		m_nic_bfc (CTL_REG_ECON1,
+			   (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+		if (copy_len == 0) {
+			eir_reg = m_nic_read (CTL_REG_EIR);
+			encReceiverReset ();
+			printf ("eth_rx: copy_len=0\n");
+			continue;
+		}
+
+		NetReceive ((unsigned char *) buffer, pkt_len);
+
+		eir_reg = m_nic_read (CTL_REG_EIR);
+	} while (pkt_cnt);	/* Use EPKTCNT not EIR.PKTIF flag, see errata pt. 6 */
+}
+
+static void encWriteReg (unsigned char regNo, unsigned char data)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x40 | regNo);	/* write in regNo */
+	spi_write (data);
+
+	enc_disable ();
+	enc_enable ();
+
+	spi_write (0x1f);	/* write reg 0x1f */
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encWriteRegRetry (unsigned char regNo, unsigned char data, int c)
+{
+	unsigned char readback;
+	int i;
+
+	spi_lock ();
+
+	for (i = 0; i < c; i++) {
+		enc_cfg_spi ();
+		enc_enable ();
+
+		spi_write (0x40 | regNo);	/* write in regNo */
+		spi_write (data);
+
+		enc_disable ();
+		enc_enable ();
+
+		spi_write (0x1f);	/* write reg 0x1f */
+
+		enc_disable ();
+
+		spi_unlock ();	/* we must unlock spi first */
+
+		readback = encReadReg (regNo);
+
+		spi_lock ();
+
+		if (readback == data)
+			break;
+	}
+	spi_unlock ();
+
+	if (i == c) {
+		printf ("enc28j60: write reg %d failed\n", regNo);
+	}
+}
+
+static unsigned char encReadReg (unsigned char regNo)
+{
+	unsigned char rxByte;
+
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x1f);	/* read reg 0x1f */
+
+	bank = spi_read () & 0x3;
+
+	enc_disable ();
+	enc_enable ();
+
+	spi_write (regNo);
+	rxByte = spi_read ();
+
+	/* check if MAC or MII register */
+	if (((bank == 2) && (regNo <= 0x1a)) ||
+	    ((bank == 3) && (regNo <= 0x05 || regNo == 0x0a))) {
+		/* ignore first byte and read another byte */
+		rxByte = spi_read ();
+	}
+
+	enc_disable ();
+	spi_unlock ();
+
+	return rxByte;
+}
+
+static void encReadBuff (unsigned short length, unsigned char *pBuff)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x20 | 0x1a);	/* read buffer memory */
+
+	while (length--) {
+		if (pBuff != NULL)
+			*pBuff++ = spi_read ();
+		else
+			spi_write (0);
+	}
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encWriteBuff (unsigned short length, unsigned char *pBuff)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x60 | 0x1a);	/* write buffer memory */
+
+	spi_write (0x00);	/* control byte */
+
+	while (length--)
+		spi_write (*pBuff++);
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encBitSet (unsigned char regNo, unsigned char data)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x80 | regNo);	/* bit field set */
+	spi_write (data);
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encBitClr (unsigned char regNo, unsigned char data)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0xA0 | regNo);	/* bit field clear */
+	spi_write (data);
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encReset (void)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0xff);	/* soft reset */
+
+	enc_disable ();
+	spi_unlock ();
+
+	/* sleep 1 ms. See errata pt. 2 */
+	udelay (1000);
+}
+
+static void encInit (unsigned char *pEthAddr)
+{
+	unsigned short phid1 = 0;
+	unsigned short phid2 = 0;
+
+	/* switch to bank 0 */
+	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+	/*
+	 * Setup the buffer space. The reset values are valid for the
+	 * other pointers.
+	 */
+	/* We shall not write to ERXST, see errata pt. 5. Instead we
+	   have to make sure that ENC_RX_BUS_START is 0. */
+	m_nic_write_retry (CTL_REG_ERXSTL, (ENC_RX_BUF_START & 0xFF), 1);
+	m_nic_write_retry (CTL_REG_ERXSTH, (ENC_RX_BUF_START >> 8), 1);
+
+	/* taken from the Linux driver */
+	m_nic_write_retry (CTL_REG_ERXNDL, (ENC_RX_BUF_END & 0xFF), 1);
+	m_nic_write_retry (CTL_REG_ERXNDH, (ENC_RX_BUF_END >> 8), 1);
+
+	m_nic_write_retry (CTL_REG_ERDPTL, (ENC_RX_BUF_START & 0xFF), 1);
+	m_nic_write_retry (CTL_REG_ERDPTH, (ENC_RX_BUF_START >> 8), 1);
+
+	next_pointer_lsb = (ENC_RX_BUF_START & 0xFF);
+	next_pointer_msb = (ENC_RX_BUF_START >> 8);
+
+	/* verify identification */
+	phid1 = phyRead (PHY_REG_PHID1);
+	phid2 = phyRead (PHY_REG_PHID2);
+
+	if (phid1 != ENC_PHID1_VALUE
+	    || (phid2 & ENC_PHID2_MASK) != ENC_PHID2_VALUE) {
+		printf ("ERROR: failed to identify controller\n");
+		printf ("phid1 = %x, phid2 = %x\n",
+			phid1, (phid2 & ENC_PHID2_MASK));
+		printf ("should be phid1 = %x, phid2 = %x\n",
+			ENC_PHID1_VALUE, ENC_PHID2_VALUE);
+	}
+
+	/*
+	 * --- MAC Initialization ---
+	 */
+
+	/* Pull MAC out of Reset */
+
+	/* switch to bank 2 */
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* enable MAC to receive frames */
+	/* added some bits from the Linux driver */
+	m_nic_write_retry (CTL_REG_MACON1
+		,(ENC_MACON1_MARXEN | ENC_MACON1_TXPAUS | ENC_MACON1_RXPAUS)
+		,10);
+
+	/* configure pad, tx-crc and duplex */
+	/* added a bit from the Linux driver */
+	m_nic_write_retry (CTL_REG_MACON3
+		,(ENC_MACON3_PADCFG0 | ENC_MACON3_TXCRCEN | ENC_MACON3_FRMLNEN)
+		,10);
+
+	/* added 4 new lines from the Linux driver */
+	/* Allow infinite deferals if the medium is continously busy */
+	m_nic_write_retry(CTL_REG_MACON4, (1<<6) /*ENC_MACON4_DEFER*/, 10);
+
+	/* Late collisions occur beyond 63 bytes */
+	m_nic_write_retry(CTL_REG_MACLCON2, 63, 10);
+
+	/* Set (low byte) Non-Back-to_Back Inter-Packet Gap. Recommended 0x12 */
+	m_nic_write_retry(CTL_REG_MAIPGL, 0x12, 10);
+
+	/*
+	* Set (high byte) Non-Back-to_Back Inter-Packet Gap. Recommended
+	* 0x0c for half-duplex. Nothing for full-duplex
+	*/
+	m_nic_write_retry(CTL_REG_MAIPGH, 0x0C, 10);
+
+	/* set maximum frame length */
+	m_nic_write_retry (CTL_REG_MAMXFLL, (ENC_MAX_FRM_LEN & 0xff), 10);
+	m_nic_write_retry (CTL_REG_MAMXFLH, (ENC_MAX_FRM_LEN >> 8), 10);
+
+	/*
+	 * Set MAC back-to-back inter-packet gap. Recommended 0x12 for half duplex
+	 * and 0x15 for full duplex.
+	 */
+	m_nic_write_retry (CTL_REG_MABBIPG, 0x12, 10);
+
+	/* set MAC address */
+
+	/* switch to bank 3 */
+	m_nic_bfs (CTL_REG_ECON1, (ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1));
+
+	m_nic_write_retry (CTL_REG_MAADR0, pEthAddr[5], 1);
+	m_nic_write_retry (CTL_REG_MAADR1, pEthAddr[4], 1);
+	m_nic_write_retry (CTL_REG_MAADR2, pEthAddr[3], 1);
+	m_nic_write_retry (CTL_REG_MAADR3, pEthAddr[2], 1);
+	m_nic_write_retry (CTL_REG_MAADR4, pEthAddr[1], 1);
+	m_nic_write_retry (CTL_REG_MAADR5, pEthAddr[0], 1);
+
+	/*
+	* PHY Initialization taken from the Linux driver
+	 */
+
+	/* Prevent automatic loopback of data beeing transmitted by setting
+	   ENC_PHCON2_HDLDIS */
+	phyWrite(PHY_REG_PHCON2, (1<<8));
+
+	/* LEDs configuration
+	 * LEDA: LACFG = 0100 -> display link status
+	 * LEDB: LBCFG = 0111 -> display TX & RX activity
+	 * STRCH = 1 -> LED pulses
+	 */
+	phyWrite(PHY_REG_PHLCON, 0x0472);
+
+	/* Reset PDPXMD-bit => half duplex */
+	phyWrite(PHY_REG_PHCON1, 0);
+
+	/*
+	 * Receive settings
+	 */
+
+#ifdef CONFIG_USE_IRQ
+	/* enable interrupts */
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_PKTIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_TXIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_RXERIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_TXERIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_INTIE);
+#endif
+}
+
+/*****************************************************************************
+ *
+ * Description:
+ *    Read PHY registers.
+ *
+ *    NOTE! This function will change to Bank 2.
+ *
+ * Params:
+ *    [in] addr address of the register to read
+ *
+ * Returns:
+ *    The value in the register
+ */
+static unsigned short phyRead (unsigned char addr)
+{
+	unsigned short ret = 0;
+
+	/* move to bank 2 */
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* write address to MIREGADR */
+	m_nic_write (CTL_REG_MIREGADR, addr);
+
+	/* set MICMD.MIIRD */
+	m_nic_write (CTL_REG_MICMD, ENC_MICMD_MIIRD);
+
+	/* taken from the Linux driver */
+	/* move to bank 3 */
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* poll MISTAT.BUSY bit until operation is complete */
+	while ((m_nic_read (CTL_REG_MISTAT) & ENC_MISTAT_BUSY) != 0) {
+		static int cnt = 0;
+
+		if (cnt++ >= 1000) {
+			/* GJ - this seems extremely dangerous! */
+			/* printf("#"); */
+			cnt = 0;
+		}
+	}
+
+	/* taken from the Linux driver */
+	/* move to bank 2 */
+	m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* clear MICMD.MIIRD */
+	m_nic_write (CTL_REG_MICMD, 0);
+
+	ret = (m_nic_read (CTL_REG_MIRDH) << 8);
+	ret |= (m_nic_read (CTL_REG_MIRDL) & 0xFF);
+
+	return ret;
+}
+
+/*****************************************************************************
+ *
+ * Taken from the Linux driver.
+ * Description:
+ * Write PHY registers.
+ *
+ * NOTE! This function will change to Bank 3.
+ *
+ * Params:
+ * [in] addr address of the register to write to
+ * [in] data to be written
+ *
+ * Returns:
+ *    None
+ */
+static void phyWrite(unsigned char addr, unsigned short data)
+{
+	/* move to bank 2 */
+	m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* write address to MIREGADR */
+	m_nic_write(CTL_REG_MIREGADR, addr);
+
+	m_nic_write(CTL_REG_MIWRL, data & 0xff);
+	m_nic_write(CTL_REG_MIWRH, data >> 8);
+
+	/* move to bank 3 */
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* poll MISTAT.BUSY bit until operation is complete */
+	while((m_nic_read(CTL_REG_MISTAT) & ENC_MISTAT_BUSY) != 0) {
+		static int cnt = 0;
+
+		if(cnt++ >= 1000) {
+			cnt = 0;
+		}
+	}
+}
diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h
index adb6ac5..ba3ada1 100644
--- a/include/configs/SMN42.h
+++ b/include/configs/SMN42.h
@@ -198,6 +198,6 @@
 #define CONFIG_INITRD_TAG
 #define CONFIG_MMC			1
 /* we use this ethernet chip */
-#define CONFIG_ENC28J60
+#define CONFIG_ENC28J60_LPC2292
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/lpc2292sodimm.h b/include/configs/lpc2292sodimm.h
index 7ce8d6d..65276a2 100644
--- a/include/configs/lpc2292sodimm.h
+++ b/include/configs/lpc2292sodimm.h
@@ -156,6 +156,6 @@
 #define CONFIG_INITRD_TAG
 #define CONFIG_MMC 1
 /* we use this ethernet chip */
-#define CONFIG_ENC28J60
+#define CONFIG_ENC28J60_LPC2292
 
 #endif	/* __CONFIG_H */

[U-Boot] [PATCH] NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.c

[Ben Warren]

  On 8/6/2010 7:06 AM, Reinhard Meyer (-VC) wrote:
> This patch is required before the upcoming new enc28j60 driver
> using SPI framework patch can be applied:
> - Move legacy enc28j60.c to enc28j60_lpc2292.c.
> - Change Makefile and the two affected boards' definition files.
>
> Tested with ./MAKEALL ARM7 that both boards still compile.
>
> Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
> ---
>   drivers/net/Makefile            |    2 +-
>   drivers/net/enc28j60.c          |  982 --------------------------------------
>   drivers/net/enc28j60_lpc2292.c  |  983 +++++++++++++++++++++++++++++++++++++++
>   include/configs/SMN42.h         |    2 +-
>   include/configs/lpc2292sodimm.h |    2 +-
>   5 files changed, 986 insertions(+), 985 deletions(-)
>   delete mode 100644 drivers/net/enc28j60.c
>   create mode 100644 drivers/net/enc28j60_lpc2292.c
Please use 'git mv' followed by 'git format-patch -C' when moving 
files.  It's much easier to review.

regards,
Ben

[U-Boot] [PATCH v2] NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.c

[Reinhard Meyer]

This patch is required before the upcoming new enc28j60 driver
using SPI framework patch can be applied:
- Move legacy enc28j60.c to enc28j60_lpc2292.c.
- Change Makefile and the two affected boards' definition files.

Tested with ./MAKEALL ARM7 that both boards still compile.

Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
---
 now with -C option on format-patch. Cheers!

 drivers/net/Makefile                           |    2 +-
 drivers/net/{enc28j60.c => enc28j60_lpc2292.c} |    1 +
 include/configs/SMN42.h                        |    2 +-
 include/configs/lpc2292sodimm.h                |    2 +-
 4 files changed, 4 insertions(+), 3 deletions(-)
 rename drivers/net/{enc28j60.c => enc28j60_lpc2292.c} (99%)

diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 218eeff..479954d 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -39,7 +39,7 @@ COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o
 COBJS-$(CONFIG_DNET) += dnet.o
 COBJS-$(CONFIG_E1000) += e1000.o
 COBJS-$(CONFIG_EEPRO100) += eepro100.o
-COBJS-$(CONFIG_ENC28J60) += enc28j60.o
+COBJS-$(CONFIG_ENC28J60_LPC2292) += enc28j60_lpc2292.o
 COBJS-$(CONFIG_EP93XX) += ep93xx_eth.o
 COBJS-$(CONFIG_ETHOC) += ethoc.o
 COBJS-$(CONFIG_FEC_MXC) += fec_mxc.o
diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60_lpc2292.c
similarity index 99%
rename from drivers/net/enc28j60.c
rename to drivers/net/enc28j60_lpc2292.c
index 3238a50..bf95052 100644
--- a/drivers/net/enc28j60.c
+++ b/drivers/net/enc28j60_lpc2292.c
@@ -15,6 +15,7 @@
  * MA 02111-1307 USA
  */
 
+#warning This driver is depreciated. Please update to new SPI framework enc28j60 driver
 #include <config.h>
 #include <common.h>
 #include <net.h>
diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h
index adb6ac5..ba3ada1 100644
--- a/include/configs/SMN42.h
+++ b/include/configs/SMN42.h
@@ -198,6 +198,6 @@
 #define CONFIG_INITRD_TAG
 #define CONFIG_MMC			1
 /* we use this ethernet chip */
-#define CONFIG_ENC28J60
+#define CONFIG_ENC28J60_LPC2292
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/lpc2292sodimm.h b/include/configs/lpc2292sodimm.h
index 7ce8d6d..65276a2 100644
--- a/include/configs/lpc2292sodimm.h
+++ b/include/configs/lpc2292sodimm.h
@@ -156,6 +156,6 @@
 #define CONFIG_INITRD_TAG
 #define CONFIG_MMC 1
 /* we use this ethernet chip */
-#define CONFIG_ENC28J60
+#define CONFIG_ENC28J60_LPC2292
 
 #endif	/* __CONFIG_H */

[U-Boot] [PATCH] NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.c

[Mike Frysinger]

On Friday, August 06, 2010 12:31:13 Ben Warren wrote:
>   On 8/6/2010 7:06 AM, Reinhard Meyer (-VC) wrote:
> > This patch is required before the upcoming new enc28j60 driver
> > using SPI framework patch can be applied:
> > - Move legacy enc28j60.c to enc28j60_lpc2292.c.
> > - Change Makefile and the two affected boards' definition files.
> > 
> > Tested with ./MAKEALL ARM7 that both boards still compile.
> > 
> > Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
> > ---
> > 
> >   drivers/net/Makefile            |    2 +-
> >   drivers/net/enc28j60.c          |  982
> >   -------------------------------------- drivers/net/enc28j60_lpc2292.c 
> >   |  983 +++++++++++++++++++++++++++++++++++++++ include/configs/SMN42.h
> >           |    2 +-
> >   include/configs/lpc2292sodimm.h |    2 +-
> >   5 files changed, 986 insertions(+), 985 deletions(-)
> >   delete mode 100644 drivers/net/enc28j60.c
> >   create mode 100644 drivers/net/enc28j60_lpc2292.c
> 
> Please use 'git mv' followed by 'git format-patch -C' when moving
> files.  It's much easier to review.

-C should figure things out without needing `git mv`
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100806/ce3c91ef/attachment.pgp 

[U-Boot] [PATCH] NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.c

[Reinhard Meyer]

Mike Frysinger wrote:
>> Please use 'git mv' followed by 'git format-patch -C' when moving
>> files.  It's much easier to review.
>>     
>
> -C should figure things out without needing `git mv`
> -mike
>   
I had used "git mv" anyway, and "git status" showed it nicely. After 
"git format-patch master"
I was wondering why it became a delete/create action.

Reinhard

[U-Boot] [PATCH v2] NET: move legacy enc28j60.c to sidetrack as enc28j60_lpc2292.c

[Ben Warren]

  Hello Reinhard,

On 8/6/2010 9:42 AM, Reinhard Meyer (-VC) wrote:
> This patch is required before the upcoming new enc28j60 driver
> using SPI framework patch can be applied:
> - Move legacy enc28j60.c to enc28j60_lpc2292.c.
> - Change Makefile and the two affected boards' definition files.
>
> Tested with ./MAKEALL ARM7 that both boards still compile.
>
> Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
> ---
Applied to net/next

regards,
Ben