* [PATCHv4 2/3] boards: amlogic: add Beelink GT1 Ultimate defconfig
@ 2023-03-26 12:43 exkc_maillist
2023-03-26 14:48 ` Christian Hewitt
0 siblings, 1 reply; 2+ messages in thread
From: exkc_maillist @ 2023-03-26 12:43 UTC (permalink / raw)
To: u-boot-amlogic
Add configuration for the Beelink GT1 Ultimate board.
Signed-off-by: Karl Chan <exxxxkc@getgoogleoff.me>
---
configs/beelink-gt1-ultimate_defconfig | 85 ++++++++++++++++++++++++++
1 file changed, 85 insertions(+)
create mode 100644 configs/beelink-gt1-ultimate_defconfig
diff --git a/configs/beelink-gt1-ultimate_defconfig b/configs/beelink-gt1-ultimate_defconfig
new file mode 100644
index 0000000000..b5ed30fab4
--- /dev/null
+++ b/configs/beelink-gt1-ultimate_defconfig
@@ -0,0 +1,85 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0xFFFF0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxm-gt1-ultimate"
+CONFIG_DM_RESET=y
+CONFIG_MESON_GXM=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" gt1-ultimate"
+CONFIG_SYS_LOAD_ADDR=0x1000000
+CONFIG_DEBUG_UART=y
+CONFIG_REMAKE_ELF=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_USE_PREBOOT=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+CONFIG_SYS_MAXARGS=32
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_ADC=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SARADC_MESON=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_MDIO_MUX=y
+CONFIG_ETH_DESIGNWARE_MESON8B=y
+CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MESON_GXL_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXL=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MESON_SPIFC=y
+CONFIG_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_GXL=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_SPLASH_SCREEN=y
+CONFIG_SPLASH_SCREEN_ALIGN=y
+CONFIG_VIDEO_BMP_RLE8=y
+CONFIG_BMP_16BPP=y
+CONFIG_BMP_24BPP=y
+CONFIG_BMP_32BPP=y
+CONFIG_OF_LIBFDT_OVERLAY=y
--
2.39.2
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCHv4 2/3] boards: amlogic: add Beelink GT1 Ultimate defconfig
2023-03-26 12:43 [PATCHv4 2/3] boards: amlogic: add Beelink GT1 Ultimate defconfig exkc_maillist
@ 2023-03-26 14:48 ` Christian Hewitt
0 siblings, 0 replies; 2+ messages in thread
From: Christian Hewitt @ 2023-03-26 14:48 UTC (permalink / raw)
To: u-boot-amlogic, exkc_maillist
> On 26 Mar 2023, at 4:43 pm, exkc_maillist via groups.io <exkc_maillist=list.ru@groups.io> wrote:
>
> Add configuration for the Beelink GT1 Ultimate board.
>
> Signed-off-by: Karl Chan <exxxxkc@getgoogleoff.me>
> ---
> configs/beelink-gt1-ultimate_defconfig | 85 ++++++++++++++++++++++++++
> 1 file changed, 85 insertions(+)
> create mode 100644 configs/beelink-gt1-ultimate_defconfig
>
> diff --git a/configs/beelink-gt1-ultimate_defconfig b/configs/beelink-gt1-ultimate_defconfig
> new file mode 100644
> index 0000000000..b5ed30fab4
> --- /dev/null
> +++ b/configs/beelink-gt1-ultimate_defconfig
> @@ -0,0 +1,85 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_MESON=y
> +CONFIG_TEXT_BASE=0x01000000
> +CONFIG_NR_DRAM_BANKS=1
> +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
> +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000
> +CONFIG_ENV_SIZE=0x10000
> +CONFIG_ENV_OFFSET=0xFFFF0000
> +CONFIG_ENV_SECT_SIZE=0x10000
^ Are these two really needed?
> +CONFIG_DM_GPIO=y
> +CONFIG_DEFAULT_DEVICE_TREE="meson-gxm-gt1-ultimate"
> +CONFIG_DM_RESET=y
> +CONFIG_MESON_GXM=y
> +CONFIG_DEBUG_UART_BASE=0xc81004c0
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_IDENT_STRING=" gt1-ultimate"
> +CONFIG_SYS_LOAD_ADDR=0x1000000
> +CONFIG_DEBUG_UART=y
> +CONFIG_REMAKE_ELF=y
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_USE_PREBOOT=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +CONFIG_MISC_INIT_R=y
> +CONFIG_SYS_MAXARGS=32
> +# CONFIG_CMD_BDI is not set
> +# CONFIG_CMD_IMI is not set
> +CONFIG_CMD_ADC=y
> +CONFIG_CMD_GPIO=y
> +# CONFIG_CMD_LOADS is not set
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF_TEST=y
^ not required
> +CONFIG_CMD_SPI=y
^ not required (board has no SPI)
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_OF_CONTROL=y
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
^ not possible if no SPI
> +CONFIG_SARADC_MESON=y
> +CONFIG_MMC_MESON_GX=y
> +CONFIG_MTD=y
> +CONFIG_DM_SPI_FLASH=y
> +CONFIG_SPI_FLASH_GIGADEVICE=y
^ These two not required if no SPI
> +CONFIG_PHY_REALTEK=y
> +CONFIG_DM_MDIO=y
> +CONFIG_DM_MDIO_MUX=y
> +CONFIG_ETH_DESIGNWARE_MESON8B=y
> +CONFIG_MDIO_MUX_MMIOREG=y
> +CONFIG_MESON_GXL_USB_PHY=y
> +CONFIG_PINCTRL=y
> +CONFIG_PINCTRL_MESON_GXL=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_MESON_EE_POWER_DOMAIN=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DEBUG_UART_ANNOUNCE=y
> +CONFIG_DEBUG_UART_SKIP_INIT=y
> +CONFIG_MESON_SERIAL=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_MESON_SPIFC=y
^ These three not required if no SPI
> +CONFIG_USB=y
> +CONFIG_DM_USB_GADGET=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_DWC3=y
> +# CONFIG_USB_DWC3_GADGET is not set
> +CONFIG_USB_DWC3_MESON_GXL=y
> +CONFIG_USB_KEYBOARD=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
> +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
> +CONFIG_USB_GADGET_DWC2_OTG=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_VIDEO=y
> +CONFIG_SYS_WHITE_ON_BLACK=y
> +CONFIG_VIDEO_MESON=y
> +CONFIG_VIDEO_DT_SIMPLEFB=y
> +CONFIG_SPLASH_SCREEN=y
> +CONFIG_SPLASH_SCREEN_ALIGN=y
> +CONFIG_VIDEO_BMP_RLE8=y
> +CONFIG_BMP_16BPP=y
> +CONFIG_BMP_24BPP=y
> +CONFIG_BMP_32BPP=y
> +CONFIG_OF_LIBFDT_OVERLAY=y
GT1 does not have SPI-NOR flash on the board so SPI options
are not required in the board config.
Christian
> --
> 2.39.2
>
>
>
>
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2023-03-26 14:48 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-03-26 12:43 [PATCHv4 2/3] boards: amlogic: add Beelink GT1 Ultimate defconfig exkc_maillist
2023-03-26 14:48 ` Christian Hewitt
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.