* [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
@ 2013-08-10 17:05 ` Javier Martinez Canillas
0 siblings, 0 replies; 14+ messages in thread
From: Javier Martinez Canillas @ 2013-08-10 17:05 UTC (permalink / raw)
To: Benoit Cousson
Cc: Tony Lindgren, Enric Balletbo, Ezequiel Garcia, linux-omap,
linux-arm-kernel
Hi,
While reviewing the submission of a DT file for a new board
based on the am3352 SoC, I noticed that am33xx*.dts files needed
some cleanups. All am33xx based board files redefine device nodes
that are already defined in the included am33xx.dtsi file.
This not only makes the DTS harder to maintain without any benefit
but also leaks SoC internal details to board files such as how the
OCP interconnect is modeled (currently just a flat representation)
and the addresses of some IP modules that are part of the SoC and
are not going to change from board to board.
This patch-set cleans these board files and is composed of the
following patches:
[PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included
[PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device
NOTE: I don't own any of these am33xx based boards so I was only
able to build test the changes. However I compared the generated
dtb before and after the changes and the disassembled DTS with
dtc -I dtb -O dts foo.dtb > bar.dts are identical.
Even though the binary dtb is the same and there shouldn't be
any visible changes, boot testing will be highly appreciated.
Thanks a lot and best regards,
Javier
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
@ 2013-08-10 17:05 ` Javier Martinez Canillas
0 siblings, 0 replies; 14+ messages in thread
From: Javier Martinez Canillas @ 2013-08-10 17:05 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
While reviewing the submission of a DT file for a new board
based on the am3352 SoC, I noticed that am33xx*.dts files needed
some cleanups. All am33xx based board files redefine device nodes
that are already defined in the included am33xx.dtsi file.
This not only makes the DTS harder to maintain without any benefit
but also leaks SoC internal details to board files such as how the
OCP interconnect is modeled (currently just a flat representation)
and the addresses of some IP modules that are part of the SoC and
are not going to change from board to board.
This patch-set cleans these board files and is composed of the
following patches:
[PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included
[PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device
NOTE: I don't own any of these am33xx based boards so I was only
able to build test the changes. However I compared the generated
dtb before and after the changes and the disassembled DTS with
dtc -I dtb -O dts foo.dtb > bar.dts are identical.
Even though the binary dtb is the same and there shouldn't be
any visible changes, boot testing will be highly appreciated.
Thanks a lot and best regards,
Javier
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included file
2013-08-10 17:05 ` Javier Martinez Canillas
@ 2013-08-10 17:05 ` Javier Martinez Canillas
-1 siblings, 0 replies; 14+ messages in thread
From: Javier Martinez Canillas @ 2013-08-10 17:05 UTC (permalink / raw)
To: Benoit Cousson
Cc: Tony Lindgren, Enric Balletbo, Ezequiel Garcia, linux-omap,
linux-arm-kernel, Javier Martinez Canillas
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
---
arch/arm/boot/dts/am335x-bone.dts | 176 ++++++++++++------------
arch/arm/boot/dts/am335x-evm.dts | 254 ++++++++++++++++++------------------
arch/arm/boot/dts/am335x-evmsk.dts | 258 ++++++++++++++++++------------------
3 files changed, 344 insertions(+), 344 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index 04feaf8..f0d53fe 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -24,94 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux@44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
- 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
- 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
- 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
- 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
- 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
ocp {
uart0: serial@44e09000 {
pinctrl-names = "default";
@@ -168,6 +80,94 @@
};
};
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
+ 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
+ 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
+ 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
+ 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+};
+
/include/ "tps65217.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index a16bb96..565b15c 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -24,133 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux@44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
-
- matrix_keypad_s0: matrix_keypad_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
- >;
- };
-
- volume_keys_s0: volume_keys_s0 {
- pinctrl-single,pins = <
- 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
- 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
- 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- nandflash_pins_s0: nandflash_pins_s0 {
- pinctrl-single,pins = <
- 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
- 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
- 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
- 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
- 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
- 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
- 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
- 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
- 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
- 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
- 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
- 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
- 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
- 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
- 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
- >;
- };
-
- ecap0_pins: backlight_pins {
- pinctrl-single,pins = <
- 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
ocp {
uart0: serial@44e09000 {
pinctrl-names = "default";
@@ -376,6 +249,133 @@
};
};
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
+
+ matrix_keypad_s0: matrix_keypad_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
+ >;
+ };
+
+ volume_keys_s0: volume_keys_s0 {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
+ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
+ 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ nandflash_pins_s0: nandflash_pins_s0 {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+
+ ecap0_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+};
+
#include "tps65910.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 9e00eef..a0afb10 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -30,135 +30,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux@44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
- 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
- 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
- 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
- >;
- };
-
- gpio_keys_s0: gpio_keys_s0 {
- pinctrl-single,pins = <
- 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */
- 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
- 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
- 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- ecap2_pins: backlight_pins {
- pinctrl-single,pins = <
- 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
-
- /* Slave 2 */
- 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
- 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
- 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
- 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-
- /* Slave 2 reset value*/
- 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
ocp {
uart0: serial@44e09000 {
pinctrl-names = "default";
@@ -304,6 +175,135 @@
};
};
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
+ 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
+ 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
+ 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
+ >;
+ };
+
+ gpio_keys_s0: gpio_keys_s0 {
+ pinctrl-single,pins = <
+ 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */
+ 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
+ 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ ecap2_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+
+ /* Slave 2 */
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
+ 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
+ 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
+ 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+
+ /* Slave 2 reset value*/
+ 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+};
+
#include "tps65910.dtsi"
&tps {
--
1.7.7.6
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included file
@ 2013-08-10 17:05 ` Javier Martinez Canillas
0 siblings, 0 replies; 14+ messages in thread
From: Javier Martinez Canillas @ 2013-08-10 17:05 UTC (permalink / raw)
To: linux-arm-kernel
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
---
arch/arm/boot/dts/am335x-bone.dts | 176 ++++++++++++------------
arch/arm/boot/dts/am335x-evm.dts | 254 ++++++++++++++++++------------------
arch/arm/boot/dts/am335x-evmsk.dts | 258 ++++++++++++++++++------------------
3 files changed, 344 insertions(+), 344 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index 04feaf8..f0d53fe 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -24,94 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux at 44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
- 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
- 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
- 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
- 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
- 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
ocp {
uart0: serial at 44e09000 {
pinctrl-names = "default";
@@ -168,6 +80,94 @@
};
};
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
+ 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
+ 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
+ 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
+ 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+};
+
/include/ "tps65217.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index a16bb96..565b15c 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -24,133 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux at 44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
-
- matrix_keypad_s0: matrix_keypad_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
- >;
- };
-
- volume_keys_s0: volume_keys_s0 {
- pinctrl-single,pins = <
- 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
- 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
- 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- nandflash_pins_s0: nandflash_pins_s0 {
- pinctrl-single,pins = <
- 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
- 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
- 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
- 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
- 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
- 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
- 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
- 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
- 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
- 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
- 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
- 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
- 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
- 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
- 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
- >;
- };
-
- ecap0_pins: backlight_pins {
- pinctrl-single,pins = <
- 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
ocp {
uart0: serial at 44e09000 {
pinctrl-names = "default";
@@ -376,6 +249,133 @@
};
};
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
+
+ matrix_keypad_s0: matrix_keypad_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
+ >;
+ };
+
+ volume_keys_s0: volume_keys_s0 {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
+ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
+ 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ nandflash_pins_s0: nandflash_pins_s0 {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+
+ ecap0_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+};
+
#include "tps65910.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 9e00eef..a0afb10 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -30,135 +30,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux at 44e10800 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
- 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
- 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
- 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
- >;
- };
-
- gpio_keys_s0: gpio_keys_s0 {
- pinctrl-single,pins = <
- 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */
- 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
- 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
- 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */
- >;
- };
-
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
- };
-
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
- };
-
- ecap2_pins: backlight_pins {
- pinctrl-single,pins = <
- 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
-
- /* Slave 2 */
- 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
- 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
- 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
- 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
- >;
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
-
- /* Slave 2 reset value*/
- 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
- };
-
ocp {
uart0: serial at 44e09000 {
pinctrl-names = "default";
@@ -304,6 +175,135 @@
};
};
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
+ 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
+ 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
+ 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
+ >;
+ };
+
+ gpio_keys_s0: gpio_keys_s0 {
+ pinctrl-single,pins = <
+ 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */
+ 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
+ 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ ecap2_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+
+ /* Slave 2 */
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
+ 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
+ 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
+ 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+
+ /* Slave 2 reset value*/
+ 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+};
+
#include "tps65910.dtsi"
&tps {
--
1.7.7.6
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device nodes
2013-08-10 17:05 ` Javier Martinez Canillas
@ 2013-08-10 17:05 ` Javier Martinez Canillas
-1 siblings, 0 replies; 14+ messages in thread
From: Javier Martinez Canillas @ 2013-08-10 17:05 UTC (permalink / raw)
To: Benoit Cousson
Cc: Tony Lindgren, Enric Balletbo, Ezequiel Garcia, linux-omap,
linux-arm-kernel, Javier Martinez Canillas
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefe this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
---
arch/arm/boot/dts/am335x-bone.dts | 41 ++---
arch/arm/boot/dts/am335x-evm.dts | 322 ++++++++++++++++++------------------
arch/arm/boot/dts/am335x-evmsk.dts | 116 +++++++-------
3 files changed, 236 insertions(+), 243 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index f0d53fe..721cad2 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -24,28 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- ocp {
- uart0: serial@44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c@44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps@24 {
- reg = <0x24>;
- };
-
- };
- };
-
leds {
pinctrl-names = "default";
pinctrl-0 = <&user_leds_s0>;
@@ -168,6 +146,25 @@
};
};
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@24 {
+ reg = <0x24>;
+ };
+};
+
/include/ "tps65217.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 565b15c..a7b1dbd 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -24,168 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- ocp {
- uart0: serial@44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c@44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps@2d {
- reg = <0x2d>;
- };
- };
-
- i2c1: i2c@4802a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
-
- status = "okay";
- clock-frequency = <100000>;
-
- lis331dlh: lis331dlh@18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
-
- tsl2550: tsl2550@39 {
- compatible = "taos,tsl2550";
- reg = <0x39>;
- };
-
- tmp275: tmp275@48 {
- compatible = "ti,tmp275";
- reg = <0x48>;
- };
- };
-
- elm: elm@48080000 {
- status = "okay";
- };
-
- epwmss0: epwmss@48300000 {
- status = "okay";
-
- ecap0: ecap@48300100 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ecap0_pins>;
- };
- };
-
- gpmc: gpmc@50000000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nandflash_pins_s0>;
- ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
- nand@0,0 {
- reg = <0 0 0>; /* CS0, offset 0 */
- nand-bus-width = <8>;
- ti,nand-ecc-opt = "bch8";
- gpmc,device-nand = "true";
- gpmc,device-width = <1>;
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <44>;
- gpmc,cs-wr-off-ns = <44>;
- gpmc,adv-on-ns = <6>;
- gpmc,adv-rd-off-ns = <34>;
- gpmc,adv-wr-off-ns = <44>;
- gpmc,we-on-ns = <0>;
- gpmc,we-off-ns = <40>;
- gpmc,oe-on-ns = <0>;
- gpmc,oe-off-ns = <54>;
- gpmc,access-ns = <64>;
- gpmc,rd-cycle-ns = <82>;
- gpmc,wr-cycle-ns = <82>;
- gpmc,wait-on-read = "true";
- gpmc,wait-on-write = "true";
- gpmc,bus-turnaround-ns = <0>;
- gpmc,cycle2cycle-delay-ns = <0>;
- gpmc,clk-activation-ns = <0>;
- gpmc,wait-monitoring-ns = <0>;
- gpmc,wr-access-ns = <40>;
- gpmc,wr-data-mux-bus-ns = <0>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- elm_id = <&elm>;
-
- /* MTD partition table */
- partition@0 {
- label = "SPL1";
- reg = <0x00000000 0x000020000>;
- };
-
- partition@1 {
- label = "SPL2";
- reg = <0x00020000 0x00020000>;
- };
-
- partition@2 {
- label = "SPL3";
- reg = <0x00040000 0x00020000>;
- };
-
- partition@3 {
- label = "SPL4";
- reg = <0x00060000 0x00020000>;
- };
-
- partition@4 {
- label = "U-boot";
- reg = <0x00080000 0x001e0000>;
- };
-
- partition@5 {
- label = "environment";
- reg = <0x00260000 0x00020000>;
- };
-
- partition@6 {
- label = "Kernel";
- reg = <0x00280000 0x00500000>;
- };
-
- partition@7 {
- label = "File-System";
- reg = <0x00780000 0x0F880000>;
- };
- };
- };
- };
-
vbat: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -376,6 +214,166 @@
};
};
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@2d {
+ reg = <0x2d>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ lis331dlh: lis331dlh@18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+
+ tsl2550: tsl2550@39 {
+ compatible = "taos,tsl2550";
+ reg = <0x39>;
+ };
+
+ tmp275: tmp275@48 {
+ compatible = "ti,tmp275";
+ reg = <0x48>;
+ };
+};
+
+&elm {
+ status = "okay";
+};
+
+&epwmss0 {
+ status = "okay";
+
+ ecap0: ecap@48300100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap0_pins>;
+ };
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins_s0>;
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <8>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ elm_id = <&elm>;
+
+ /* MTD partition table */
+ partition@0 {
+ label = "SPL1";
+ reg = <0x00000000 0x000020000>;
+ };
+
+ partition@1 {
+ label = "SPL2";
+ reg = <0x00020000 0x00020000>;
+ };
+
+ partition@2 {
+ label = "SPL3";
+ reg = <0x00040000 0x00020000>;
+ };
+
+ partition@3 {
+ label = "SPL4";
+ reg = <0x00060000 0x00020000>;
+ };
+
+ partition@4 {
+ label = "U-boot";
+ reg = <0x00080000 0x001e0000>;
+ };
+
+ partition@5 {
+ label = "environment";
+ reg = <0x00260000 0x00020000>;
+ };
+
+ partition@6 {
+ label = "Kernel";
+ reg = <0x00280000 0x00500000>;
+ };
+
+ partition@7 {
+ label = "File-System";
+ reg = <0x00780000 0x0F880000>;
+ };
+ };
+};
+
#include "tps65910.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index a0afb10..d3e8ed2 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -30,65 +30,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- ocp {
- uart0: serial@44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c@44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps@2d {
- reg = <0x2d>;
- };
-
- lis331dlh: lis331dlh@18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
- };
-
- epwmss2: epwmss@48304000 {
- status = "okay";
-
- ecap2: ecap@48304100 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ecap2_pins>;
- };
- };
- };
-
vbat: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -304,6 +245,63 @@
};
};
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@2d {
+ reg = <0x2d>;
+ };
+
+ lis331dlh: lis331dlh@18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+};
+
+&epwmss2 {
+ status = "okay";
+
+ ecap2: ecap@48304100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap2_pins>;
+ };
+};
+
#include "tps65910.dtsi"
&tps {
--
1.7.7.6
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device nodes
@ 2013-08-10 17:05 ` Javier Martinez Canillas
0 siblings, 0 replies; 14+ messages in thread
From: Javier Martinez Canillas @ 2013-08-10 17:05 UTC (permalink / raw)
To: linux-arm-kernel
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefe this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
---
arch/arm/boot/dts/am335x-bone.dts | 41 ++---
arch/arm/boot/dts/am335x-evm.dts | 322 ++++++++++++++++++------------------
arch/arm/boot/dts/am335x-evmsk.dts | 116 +++++++-------
3 files changed, 236 insertions(+), 243 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index f0d53fe..721cad2 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -24,28 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- ocp {
- uart0: serial at 44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c at 44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps at 24 {
- reg = <0x24>;
- };
-
- };
- };
-
leds {
pinctrl-names = "default";
pinctrl-0 = <&user_leds_s0>;
@@ -168,6 +146,25 @@
};
};
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps at 24 {
+ reg = <0x24>;
+ };
+};
+
/include/ "tps65217.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 565b15c..a7b1dbd 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -24,168 +24,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- ocp {
- uart0: serial at 44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c at 44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps at 2d {
- reg = <0x2d>;
- };
- };
-
- i2c1: i2c at 4802a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
-
- status = "okay";
- clock-frequency = <100000>;
-
- lis331dlh: lis331dlh at 18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
-
- tsl2550: tsl2550 at 39 {
- compatible = "taos,tsl2550";
- reg = <0x39>;
- };
-
- tmp275: tmp275 at 48 {
- compatible = "ti,tmp275";
- reg = <0x48>;
- };
- };
-
- elm: elm at 48080000 {
- status = "okay";
- };
-
- epwmss0: epwmss at 48300000 {
- status = "okay";
-
- ecap0: ecap at 48300100 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ecap0_pins>;
- };
- };
-
- gpmc: gpmc at 50000000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nandflash_pins_s0>;
- ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
- nand at 0,0 {
- reg = <0 0 0>; /* CS0, offset 0 */
- nand-bus-width = <8>;
- ti,nand-ecc-opt = "bch8";
- gpmc,device-nand = "true";
- gpmc,device-width = <1>;
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <44>;
- gpmc,cs-wr-off-ns = <44>;
- gpmc,adv-on-ns = <6>;
- gpmc,adv-rd-off-ns = <34>;
- gpmc,adv-wr-off-ns = <44>;
- gpmc,we-on-ns = <0>;
- gpmc,we-off-ns = <40>;
- gpmc,oe-on-ns = <0>;
- gpmc,oe-off-ns = <54>;
- gpmc,access-ns = <64>;
- gpmc,rd-cycle-ns = <82>;
- gpmc,wr-cycle-ns = <82>;
- gpmc,wait-on-read = "true";
- gpmc,wait-on-write = "true";
- gpmc,bus-turnaround-ns = <0>;
- gpmc,cycle2cycle-delay-ns = <0>;
- gpmc,clk-activation-ns = <0>;
- gpmc,wait-monitoring-ns = <0>;
- gpmc,wr-access-ns = <40>;
- gpmc,wr-data-mux-bus-ns = <0>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- elm_id = <&elm>;
-
- /* MTD partition table */
- partition at 0 {
- label = "SPL1";
- reg = <0x00000000 0x000020000>;
- };
-
- partition at 1 {
- label = "SPL2";
- reg = <0x00020000 0x00020000>;
- };
-
- partition at 2 {
- label = "SPL3";
- reg = <0x00040000 0x00020000>;
- };
-
- partition at 3 {
- label = "SPL4";
- reg = <0x00060000 0x00020000>;
- };
-
- partition at 4 {
- label = "U-boot";
- reg = <0x00080000 0x001e0000>;
- };
-
- partition at 5 {
- label = "environment";
- reg = <0x00260000 0x00020000>;
- };
-
- partition at 6 {
- label = "Kernel";
- reg = <0x00280000 0x00500000>;
- };
-
- partition at 7 {
- label = "File-System";
- reg = <0x00780000 0x0F880000>;
- };
- };
- };
- };
-
vbat: fixedregulator at 0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -376,6 +214,166 @@
};
};
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps at 2d {
+ reg = <0x2d>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ lis331dlh: lis331dlh at 18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+
+ tsl2550: tsl2550 at 39 {
+ compatible = "taos,tsl2550";
+ reg = <0x39>;
+ };
+
+ tmp275: tmp275 at 48 {
+ compatible = "ti,tmp275";
+ reg = <0x48>;
+ };
+};
+
+&elm {
+ status = "okay";
+};
+
+&epwmss0 {
+ status = "okay";
+
+ ecap0: ecap at 48300100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap0_pins>;
+ };
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins_s0>;
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+ nand at 0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <8>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ elm_id = <&elm>;
+
+ /* MTD partition table */
+ partition at 0 {
+ label = "SPL1";
+ reg = <0x00000000 0x000020000>;
+ };
+
+ partition at 1 {
+ label = "SPL2";
+ reg = <0x00020000 0x00020000>;
+ };
+
+ partition at 2 {
+ label = "SPL3";
+ reg = <0x00040000 0x00020000>;
+ };
+
+ partition at 3 {
+ label = "SPL4";
+ reg = <0x00060000 0x00020000>;
+ };
+
+ partition at 4 {
+ label = "U-boot";
+ reg = <0x00080000 0x001e0000>;
+ };
+
+ partition at 5 {
+ label = "environment";
+ reg = <0x00260000 0x00020000>;
+ };
+
+ partition at 6 {
+ label = "Kernel";
+ reg = <0x00280000 0x00500000>;
+ };
+
+ partition at 7 {
+ label = "File-System";
+ reg = <0x00780000 0x0F880000>;
+ };
+ };
+};
+
#include "tps65910.dtsi"
&tps {
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index a0afb10..d3e8ed2 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -30,65 +30,6 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- ocp {
- uart0: serial at 44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-
- status = "okay";
- };
-
- i2c0: i2c at 44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- status = "okay";
- clock-frequency = <400000>;
-
- tps: tps at 2d {
- reg = <0x2d>;
- };
-
- lis331dlh: lis331dlh at 18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
- };
-
- epwmss2: epwmss at 48304000 {
- status = "okay";
-
- ecap2: ecap at 48304100 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ecap2_pins>;
- };
- };
- };
-
vbat: fixedregulator at 0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
@@ -304,6 +245,63 @@
};
};
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps at 2d {
+ reg = <0x2d>;
+ };
+
+ lis331dlh: lis331dlh at 18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+};
+
+&epwmss2 {
+ status = "okay";
+
+ ecap2: ecap at 48304100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap2_pins>;
+ };
+};
+
#include "tps65910.dtsi"
&tps {
--
1.7.7.6
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
2013-08-10 17:05 ` Javier Martinez Canillas
@ 2013-08-13 11:45 ` Benoit Cousson
-1 siblings, 0 replies; 14+ messages in thread
From: Benoit Cousson @ 2013-08-13 11:45 UTC (permalink / raw)
To: Javier Martinez Canillas
Cc: Benoit Cousson, Tony Lindgren, Enric Balletbo, Ezequiel Garcia,
linux-omap, linux-arm-kernel, Afzal Mohammed, Lokesh Vutla
+ Few TI folks to review and test.
On 10/08/2013 19:05, Javier Martinez Canillas wrote:
> Hi,
>
> While reviewing the submission of a DT file for a new board
> based on the am3352 SoC, I noticed that am33xx*.dts files needed
> some cleanups. All am33xx based board files redefine device nodes
> that are already defined in the included am33xx.dtsi file.
>
> This not only makes the DTS harder to maintain without any benefit
> but also leaks SoC internal details to board files such as how the
> OCP interconnect is modeled (currently just a flat representation)
> and the addresses of some IP modules that are part of the SoC and
> are not going to change from board to board.
>
> This patch-set cleans these board files and is composed of the
> following patches:
>
> [PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included
> [PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device
>
> NOTE: I don't own any of these am33xx based boards so I was only
> able to build test the changes. However I compared the generated
> dtb before and after the changes and the disassembled DTS with
> dtc -I dtb -O dts foo.dtb > bar.dts are identical.
>
> Even though the binary dtb is the same and there shouldn't be
> any visible changes, boot testing will be highly appreciated.
Thanks it looks good to me.
Regards,
Benoit
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
@ 2013-08-13 11:45 ` Benoit Cousson
0 siblings, 0 replies; 14+ messages in thread
From: Benoit Cousson @ 2013-08-13 11:45 UTC (permalink / raw)
To: linux-arm-kernel
+ Few TI folks to review and test.
On 10/08/2013 19:05, Javier Martinez Canillas wrote:
> Hi,
>
> While reviewing the submission of a DT file for a new board
> based on the am3352 SoC, I noticed that am33xx*.dts files needed
> some cleanups. All am33xx based board files redefine device nodes
> that are already defined in the included am33xx.dtsi file.
>
> This not only makes the DTS harder to maintain without any benefit
> but also leaks SoC internal details to board files such as how the
> OCP interconnect is modeled (currently just a flat representation)
> and the addresses of some IP modules that are part of the SoC and
> are not going to change from board to board.
>
> This patch-set cleans these board files and is composed of the
> following patches:
>
> [PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included
> [PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device
>
> NOTE: I don't own any of these am33xx based boards so I was only
> able to build test the changes. However I compared the generated
> dtb before and after the changes and the disassembled DTS with
> dtc -I dtb -O dts foo.dtb > bar.dts are identical.
>
> Even though the binary dtb is the same and there shouldn't be
> any visible changes, boot testing will be highly appreciated.
Thanks it looks good to me.
Regards,
Benoit
^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
2013-08-13 11:45 ` Benoit Cousson
@ 2013-08-14 10:21 ` Mohammed, Afzal
-1 siblings, 0 replies; 14+ messages in thread
From: Mohammed, Afzal @ 2013-08-14 10:21 UTC (permalink / raw)
To: Benoit Cousson, Javier Martinez Canillas
Cc: Benoit Cousson, Tony Lindgren, Enric Balletbo, Ezequiel Garcia,
linux-omap, linux-arm-kernel, Vutla, Lokesh
Hi Benoit,
* Benoit Cousson, August 13, 2013 5:15 PM:
> + Few TI folks to review and test.
I am out of office, will be back early next week and then test this.
Regards
Afzal
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
@ 2013-08-14 10:21 ` Mohammed, Afzal
0 siblings, 0 replies; 14+ messages in thread
From: Mohammed, Afzal @ 2013-08-14 10:21 UTC (permalink / raw)
To: linux-arm-kernel
Hi Benoit,
* Benoit Cousson, August 13, 2013 5:15 PM:
> + Few TI folks to review and test.
I am out of office, will be back early next week and then test this.
Regards
Afzal
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
2013-08-13 11:45 ` Benoit Cousson
@ 2013-08-16 9:25 ` Rajendra Nayak
-1 siblings, 0 replies; 14+ messages in thread
From: Rajendra Nayak @ 2013-08-16 9:25 UTC (permalink / raw)
To: Benoit Cousson
Cc: Javier Martinez Canillas, Ezequiel Garcia, Tony Lindgren,
Afzal Mohammed, Enric Balletbo, Lokesh Vutla, Benoit Cousson,
linux-omap, linux-arm-kernel
On Tuesday 13 August 2013 05:15 PM, Benoit Cousson wrote:
> + Few TI folks to review and test.
>
> On 10/08/2013 19:05, Javier Martinez Canillas wrote:
>> Hi,
[]..
>>
>> Even though the binary dtb is the same and there shouldn't be
>> any visible changes, boot testing will be highly appreciated.
I just boot tested these on my BoneBlack and it boots just fine [1]
Feel free to add,
Tested-by: Rajendra Nayak <rnayak@ti.com>
[1] http://pastebin.com/Z2j6pymp
>
> Thanks it looks good to me.
>
> Regards,
> Benoit
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
@ 2013-08-16 9:25 ` Rajendra Nayak
0 siblings, 0 replies; 14+ messages in thread
From: Rajendra Nayak @ 2013-08-16 9:25 UTC (permalink / raw)
To: linux-arm-kernel
On Tuesday 13 August 2013 05:15 PM, Benoit Cousson wrote:
> + Few TI folks to review and test.
>
> On 10/08/2013 19:05, Javier Martinez Canillas wrote:
>> Hi,
[]..
>>
>> Even though the binary dtb is the same and there shouldn't be
>> any visible changes, boot testing will be highly appreciated.
I just boot tested these on my BoneBlack and it boots just fine [1]
Feel free to add,
Tested-by: Rajendra Nayak <rnayak@ti.com>
[1] http://pastebin.com/Z2j6pymp
>
> Thanks it looks good to me.
>
> Regards,
> Benoit
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
2013-08-16 9:25 ` Rajendra Nayak
@ 2013-08-16 10:47 ` Benoit Cousson
-1 siblings, 0 replies; 14+ messages in thread
From: Benoit Cousson @ 2013-08-16 10:47 UTC (permalink / raw)
To: Rajendra Nayak, Javier Martinez Canillas
Cc: Ezequiel Garcia, Tony Lindgren, Afzal Mohammed, Enric Balletbo,
Lokesh Vutla, linux-omap, linux-arm-kernel
On 16/08/2013 11:25, Rajendra Nayak wrote:
> On Tuesday 13 August 2013 05:15 PM, Benoit Cousson wrote:
>> + Few TI folks to review and test.
>>
>> On 10/08/2013 19:05, Javier Martinez Canillas wrote:
>>> Hi,
> []..
>
>>>
>>> Even though the binary dtb is the same and there shouldn't be
>>> any visible changes, boot testing will be highly appreciated.
>
> I just boot tested these on my BoneBlack and it boots just fine [1]
> Feel free to add,
> Tested-by: Rajendra Nayak <rnayak@ti.com>
Thanks Rajendra.
Javier,
I've just applied it for 3.12 with Rajendra's T-by.
Regards,
Benoit
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups
@ 2013-08-16 10:47 ` Benoit Cousson
0 siblings, 0 replies; 14+ messages in thread
From: Benoit Cousson @ 2013-08-16 10:47 UTC (permalink / raw)
To: linux-arm-kernel
On 16/08/2013 11:25, Rajendra Nayak wrote:
> On Tuesday 13 August 2013 05:15 PM, Benoit Cousson wrote:
>> + Few TI folks to review and test.
>>
>> On 10/08/2013 19:05, Javier Martinez Canillas wrote:
>>> Hi,
> []..
>
>>>
>>> Even though the binary dtb is the same and there shouldn't be
>>> any visible changes, boot testing will be highly appreciated.
>
> I just boot tested these on my BoneBlack and it boots just fine [1]
> Feel free to add,
> Tested-by: Rajendra Nayak <rnayak@ti.com>
Thanks Rajendra.
Javier,
I've just applied it for 3.12 with Rajendra's T-by.
Regards,
Benoit
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2013-08-16 10:47 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-08-10 17:05 [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups Javier Martinez Canillas
2013-08-10 17:05 ` Javier Martinez Canillas
2013-08-10 17:05 ` [PATCH 1/2] ARM: dts: AM33XX: use pinmux node defined in included file Javier Martinez Canillas
2013-08-10 17:05 ` Javier Martinez Canillas
2013-08-10 17:05 ` [PATCH 2/2] ARM: dts: AM33XX: don't redefine OCP bus and device nodes Javier Martinez Canillas
2013-08-10 17:05 ` Javier Martinez Canillas
2013-08-13 11:45 ` [PATCH 0/2] ARM: dts: AM33XX: node definition cleanups Benoit Cousson
2013-08-13 11:45 ` Benoit Cousson
2013-08-14 10:21 ` Mohammed, Afzal
2013-08-14 10:21 ` Mohammed, Afzal
2013-08-16 9:25 ` Rajendra Nayak
2013-08-16 9:25 ` Rajendra Nayak
2013-08-16 10:47 ` Benoit Cousson
2013-08-16 10:47 ` Benoit Cousson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.