* master/krogoth kernel crash for imx7D
@ 2016-06-23 17:10 Daiane Angolini
2016-06-23 18:09 ` Gary Bisson
2016-07-11 12:22 ` Fabio Estevam
0 siblings, 2 replies; 5+ messages in thread
From: Daiane Angolini @ 2016-06-23 17:10 UTC (permalink / raw)
To: meta-freescale
I'm facing the following kernel crash for imx7dsabresd. Any hint?
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 4.1.15-1.1.0+ga4d2a08 (fsl@fsl-Precision-M4800) (gcc
version 5.3.0 (GCC) ) #1 SMP PREEMPT Thu Jun 23 15:50:23 CEST 2016
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Freescale i.MX7D SabreSD Board
Reserved memory: created CMA memory pool at 0xac000000, size 320 MiB
Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
Memory policy: Data cache writealloc
PERCPU: Embedded 12 pages/cpu @ab71c000 s16908 r8192 d24052 u49152
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 698868K/1048576K available (7944K kernel code, 422K rwdata,
2832K rodata, 428K init, 440K bss, 22028K reserved, 327680K
cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80a8e398 (10777 kB)
.init : 0x80a8f000 - 0x80afa000 ( 428 kB)
.data : 0x80afa000 - 0x80b63b40 ( 423 kB)
.bss : 0x80b66000 - 0x80bd40c0 ( 441 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
Additional per-CPU info printed with stalls.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
Architected cp15 timer(s) running at 8.00MHz (phys).
clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles:
0x1d854df40, max_idle_ns: 440795202120 ns
sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
Switching to timer-based delay loop, resolution 125ns
mxc_clocksource_init 3000000
Ignoring duplicate/late registration of read_current_timer delay
clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 637086815595 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer
frequency.. 16.00 BogoMIPS (lpj=80000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
/cpus/cpu@0 missing clock-frequency property
/cpus/cpu@1 missing clock-frequency property
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80008280 - 0x800082d8
CPU1: failed to come online
Brought up 1 CPUs
SMP: Total of 1 processors activated (16.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
device-tree: Duplicate name in lcdif@30730000, renamed to "display#1"
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
DDR type is DDR3!
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver
MU is ready for cross core communication!
mxs-dma 33000000.dma-apbh: initialized
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
30800000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
30800000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator
i2c i2c-0: IMX I2C adapter registered
i2c i2c-0: can't use DMA
i2c i2c-1: IMX I2C adapter registered
i2c i2c-1: can't use DMA
i2c i2c-2: IMX I2C adapter registered
i2c i2c-2: can't use DMA
i2c i2c-3: IMX I2C adapter registered
i2c i2c-3: can't use DMA
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
<giometti@linux.it>
PTP clock support registered
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.20
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
imx rpmsg driver is registered.
Bus freq driver module loaded
futex hash table entries: 512 (order: 3, 32768 bytes)
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
backlight supply power not found, using dummy regulator
MIPI DSI driver module loaded
MIPI DSI driver module loaded
sii902x 2-0039: No reset pin found
sii902x 2-0039: Can not read edid
30730000.lcdif supply lcd not found, using dummy regulator
mxsfb 30730000.lcdif: failed to find mxc display driver
Console: switching to colour frame buffer device 60x34
mxsfb 30730000.lcdif: initialized
imx-sdma 30bd0000.sdma: no event needs to be remapped
imx-sdma 30bd0000.sdma: loaded firmware 4.2
imx-sdma 30bd0000.sdma: initialized
pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1
pfuze100-regulator 0-0008: FAB: 0, FIN: 0
pfuze100-regulator 0-0008: pfuze3000 found.
30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 279, base_baud =
1500000) is a IMX
console [ttymxc0] enabled
30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 288, base_baud =
5000000) is a IMX
30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 289, base_baud =
5000000) is a IMX
imx sema4 driver is registered.
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
input: fxos8700 as
/devices/platform/soc/30800000.aips-bus/30a30000.i2c/i2c-1/1-001e/input/input0
fxos8700 device driver probe successfully
input: fxas2100x as
/devices/platform/soc/30800000.aips-bus/30a30000.i2c/i2c-1/1-0020/input/input1
fxas2100x 1-0020: fxas2100x device driver probe successfully
spi_gpio spi4: gpio-miso property not found, switching to no-rx mode
spi_imx 30840000.ecspi: probed
CAN device driver interface
flexcan 30a10000.can: device registered (reg_base=f5a10000, irq=283)
30be0000.ethernet supply phy not found, using dummy regulator
pps pps0: new PPS source ptp0
libphy: fec_enet_mii_bus: probed
fec 30be0000.ethernet eth0: registered PHC device 0
30bf0000.ethernet supply phy not found, using dummy regulator
pps pps1: new PPS source ptp1
fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Invalid
MAC address: 00:00:00:00:00:00
fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Using
random MAC address: 46:cb:dc:d0:f3:e4
fec 30bf0000.ethernet eth1: registered PHC device 1
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-mxc: Freescale On-Chip EHCI Host driver
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usb_ehset_test
30b10200.usbmisc supply vbus-wakeup not found, using dummy regulator
30b20200.usbmisc supply vbus-wakeup not found, using dummy regulator
30b30200.usbmisc supply vbus-wakeup not found, using dummy regulator
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
input: 30370000.snvs:snvs-powerkey as
/devices/platform/soc/30000000.aips-bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input2
spi2.0 supply vcc not found, using dummy regulator
ads7846 spi2.0: touchscreen, irq 88
input: ADS7846 Touchscreen as
/devices/platform/soc/30800000.aips-bus/30800000.spba-bus/30840000.ecspi/spi_master/spi2/spi2.0/input/input3
read mpl3115 chip id 0xc4
input: mpl3115 as /devices/virtual/input/input4
mpl3115 device driver probe successfully
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
30370000.snvs:snvs- as rtc0
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x/sz) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR SANYO protocol handler initialized
IR Sharp protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR XMP protocol handler initialized
pxp-v4l2 pxp_v4l2_out: initialized
imx2-wdt 30280000.wdog: use WDOG_B to reboot.
imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
Bluetooth: HCI UART driver ver 2.3
Bluetooth: HCI UART protocol H4 registered
Bluetooth: HCI UART protocol BCSP registered
Bluetooth: HCI UART protocol ATH3K registered
usbcore: registered new interface driver bcm203x
usbcore: registered new interface driver btusb
usbcore: registered new interface driver ath3k
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
/soc/aips-bus@30800000/usdhc@30b40000: voltage-ranges unspecified
sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO
sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO
sdhci-esdhc-imx 30b40000.usdhc: No vqmmc regulator found
mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA
/soc/aips-bus@30800000/usdhc@30b50000: voltage-ranges unspecified
sdhci-esdhc-imx 30b50000.usdhc: assigned as wifi host
sdhci-esdhc-imx 30b50000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 30b50000.usdhc: No vqmmc regulator found
mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA
/soc/aips-bus@30800000/usdhc@30b60000: voltage-ranges unspecified
sdhci-esdhc-imx 30b60000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 30b60000.usdhc: No vqmmc regulator found
mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA
caam 30900000.caam: Entropy delay = 3200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 3600
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 4000
mmc0: Problem setting current limit!
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 4400
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 4800
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 5200
mmc0: new ultra high speed DDR50 SDHC card at address e624
mmcblk0: mmc0:e624 SU08G 7.40 GiB
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 5600
mmcblk0: p1 p2
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 6000
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 6400
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 6800
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 7200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 7600
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 8000
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 8400
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 8800
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 9200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 9600
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 10000
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 10400
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 10800
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 11200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 11600
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 12000
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: Entropy delay = 12400
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: failed to instantiate RNG
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at
/home/fsl/Data/fsl_yocto_community_krogoth/build_imx7sdb_qt_x11/tmp/work-shared/imx7dsabresd/kernel-source/mm/vmalloc.c:1465
caam_remove+0x6c/0x408()
Trying to vfree() nonexistent vm area (a8063000)
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.1.15-1.1.0+ga4d2a08 #1
Hardware name: Freescale i.MX7 Dual (Device Tree)
[<80015d78>] (unwind_backtrace) from [<8001271c>] (show_stack+0x10/0x14)
[<8001271c>] (show_stack) from [<80790280>] (dump_stack+0x84/0xc4)
[<80790280>] (dump_stack) from [<80034750>] (warn_slowpath_common+0x80/0xb0)
[<80034750>] (warn_slowpath_common) from [<800347b0>]
(warn_slowpath_fmt+0x30/0x40)
[<800347b0>] (warn_slowpath_fmt) from [<8056ed9c>] (caam_remove+0x6c/0x408)
[<8056ed9c>] (caam_remove) from [<8056ff10>] (caam_probe+0xdd8/0xf10)
[<8056ff10>] (caam_probe) from [<80381118>] (platform_drv_probe+0x44/0xac)
[<80381118>] (platform_drv_probe) from [<8037f9b4>]
(driver_probe_device+0x174/0x2b4)
[<8037f9b4>] (driver_probe_device) from [<8037fbc4>] (__driver_attach+0x8c/0x90)
[<8037fbc4>] (__driver_attach) from [<8037e040>] (bus_for_each_dev+0x68/0x9c)
[<8037e040>] (bus_for_each_dev) from [<8037f144>] (bus_add_driver+0x148/0x1f0)
[<8037f144>] (bus_add_driver) from [<803801c4>] (driver_register+0x78/0xf8)
[<803801c4>] (driver_register) from [<80009718>] (do_one_initcall+0x8c/0x1d4)
[<80009718>] (do_one_initcall) from [<80a8fdbc>]
(kernel_init_freeable+0x144/0x1e4)
[<80a8fdbc>] (kernel_init_freeable) from [<8078c4e4>] (kernel_init+0x8/0xe8)
[<8078c4e4>] (kernel_init) from [<8000f528>] (ret_from_fork+0x14/0x2c)
---[ end trace 0315279c11aaddc3 ]---
caam: probe of 30900000.caam failed with error -11
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = 80004000
[00000004] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.1.15-1.1.0+ga4d2a08 #1
Hardware name: Freescale i.MX7 Dual (Device Tree)
task: a807c000 ti: a8062000 task.ti: a8062000
PC is at caam_sm_startup+0x8c/0x3cc
LR is at device_add+0x154/0x56c
pc : [<8057f910>] lr : [<8037d008>] psr: a0000113
sp : a8063ed0 ip : 00000000 fp : 00000000
r10: 80af358c r9 : 00000000 r8 : 00000000
r7 : 80ad15d8 r6 : ab73bac4 r5 : a8150010 r4 : a8419840
r3 : a8493210 r2 : a8493200 r1 : 00000000 r0 : a8493200
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 8000406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xa8062210)
Stack: (0xa8063ed0 to 0xa8064000)
3ec0: 00000000 80796214 a8063ee8 a8493200
3ee0: a8150010 80aff720 80aff720 a847e1c0 80ad15d8 00000000 80ae6bcc 80af358c
3f00: 00000000 80ad1628 80aff720 80009718 80ae6ba8 8013f8ac 00000000 a80ee380
3f20: 00000000 80b073e8 60000113 00000000 abfffb76 abfffb74 807c2a24 8004c4d4
3f40: 00000000 809d7a40 00000006 00000006 80b073d0 0000010d 00000006 80b66000
3f60: 0000010d 00000006 80b66000 80b66000 80ae6bc4 80a8fdbc 00000006 00000006
3f80: 80a8f594 80050b94 00000000 8078c4dc 00000000 00000000 00000000 00000000
3fa0: 00000000 8078c4e4 00000000 8000f528 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 2fef7abf cbabedc9
[<8057f910>] (caam_sm_startup) from [<80ad1628>] (caam_sm_init+0x50/0x58)
[<80ad1628>] (caam_sm_init) from [<80009718>] (do_one_initcall+0x8c/0x1d4)
[<80009718>] (do_one_initcall) from [<80a8fdbc>]
(kernel_init_freeable+0x144/0x1e4)
[<80a8fdbc>] (kernel_init_freeable) from [<8078c4e4>] (kernel_init+0x8/0xe8)
[<8078c4e4>] (kernel_init) from [<8000f528>] (ret_from_fork+0x14/0x2c)
Code: e59d200c e2823010 e5842008 e5824068 (e5893004)
---[ end trace 0315279c11aaddc4 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: master/krogoth kernel crash for imx7D
2016-06-23 17:10 master/krogoth kernel crash for imx7D Daiane Angolini
@ 2016-06-23 18:09 ` Gary Bisson
2016-06-24 11:56 ` Daiane Angolini
2016-07-11 12:22 ` Fabio Estevam
1 sibling, 1 reply; 5+ messages in thread
From: Gary Bisson @ 2016-06-23 18:09 UTC (permalink / raw)
To: Daiane Angolini; +Cc: meta-freescale
[-- Attachment #1: Type: text/plain, Size: 19351 bytes --]
Hi Daiane,
I've had this CAAM issue in the past:
http://lists.denx.de/pipermail/u-boot/2016-March/250112.html
Are you using mainline U-Boot? If so you need to enable the secure mode,
otherwise CAAM won't work. See the patch I made on our Github repo to fix
it:
https://github.com/boundarydevices/u-boot-imx6/commit/38b5fa7e
Regards,
Gary
On Thu, Jun 23, 2016 at 7:10 PM, Daiane Angolini <daiane.list@gmail.com>
wrote:
> I'm facing the following kernel crash for imx7dsabresd. Any hint?
>
> Starting kernel ...
>
> Booting Linux on physical CPU 0x0
> Linux version 4.1.15-1.1.0+ga4d2a08 (fsl@fsl-Precision-M4800) (gcc
> version 5.3.0 (GCC) ) #1 SMP PREEMPT Thu Jun 23 15:50:23 CEST 2016
> CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
> CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
> Machine model: Freescale i.MX7D SabreSD Board
> Reserved memory: created CMA memory pool at 0xac000000, size 320 MiB
> Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
> Memory policy: Data cache writealloc
> PERCPU: Embedded 12 pages/cpu @ab71c000 s16908 r8192 d24052 u49152
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
> Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
> PID hash table entries: 4096 (order: 2, 16384 bytes)
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 698868K/1048576K available (7944K kernel code, 422K rwdata,
> 2832K rodata, 428K init, 440K bss, 22028K reserved, 327680K
> cma-reserved, 0K highmem)
> Virtual kernel memory layout:
> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
> vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
> lowmem : 0x80000000 - 0xc0000000 (1024 MB)
> pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
> modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
> .text : 0x80008000 - 0x80a8e398 (10777 kB)
> .init : 0x80a8f000 - 0x80afa000 ( 428 kB)
> .data : 0x80afa000 - 0x80b63b40 ( 423 kB)
> .bss : 0x80b66000 - 0x80bd40c0 ( 441 kB)
> SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
> Preemptible hierarchical RCU implementation.
> Additional per-CPU info printed with stalls.
> RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
> RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
> NR_IRQS:16 nr_irqs:16 16
> Architected cp15 timer(s) running at 8.00MHz (phys).
> clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles:
> 0x1d854df40, max_idle_ns: 440795202120 ns
> sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
> Switching to timer-based delay loop, resolution 125ns
> mxc_clocksource_init 3000000
> Ignoring duplicate/late registration of read_current_timer delay
> clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff,
> max_idle_ns: 637086815595 ns
> Console: colour dummy device 80x30
> Calibrating delay loop (skipped), value calculated using timer
> frequency.. 16.00 BogoMIPS (lpj=80000)
> pid_max: default: 32768 minimum: 301
> Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
> CPU: Testing write buffer coherency: ok
> /cpus/cpu@0 missing clock-frequency property
> /cpus/cpu@1 missing clock-frequency property
> CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
> Setting up static identity map for 0x80008280 - 0x800082d8
> CPU1: failed to come online
> Brought up 1 CPUs
> SMP: Total of 1 processors activated (16.00 BogoMIPS).
> CPU: All CPU(s) started in SVC mode.
> devtmpfs: initialized
> device-tree: Duplicate name in lcdif@30730000, renamed to "display#1"
> VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
> clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
> max_idle_ns: 19112604462750000 ns
> pinctrl core: initialized pinctrl subsystem
> NET: Registered protocol family 16
> DMA: preallocated 256 KiB pool for atomic coherent allocations
> cpuidle: using governor ladder
> cpuidle: using governor menu
> DDR type is DDR3!
> hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
> hw-breakpoint: maximum watchpoint size is 8 bytes.
> imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
> imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver
> MU is ready for cross core communication!
> mxs-dma 33000000.dma-apbh: initialized
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> 30800000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
> 30800000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator
> i2c i2c-0: IMX I2C adapter registered
> i2c i2c-0: can't use DMA
> i2c i2c-1: IMX I2C adapter registered
> i2c i2c-1: can't use DMA
> i2c i2c-2: IMX I2C adapter registered
> i2c i2c-2: can't use DMA
> i2c i2c-3: IMX I2C adapter registered
> i2c i2c-3: can't use DMA
> Linux video capture interface: v2.00
> pps_core: LinuxPPS API ver. 1 registered
> pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
> <giometti@linux.it>
> PTP clock support registered
> MIPI CSI2 driver module loaded
> Advanced Linux Sound Architecture Driver Initialized.
> Bluetooth: Core ver 2.20
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: SCO socket layer initialized
> Switched to clocksource arch_sys_counter
> NET: Registered protocol family 2
> TCP established hash table entries: 8192 (order: 3, 32768 bytes)
> TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> UDP hash table entries: 512 (order: 2, 16384 bytes)
> UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> NET: Registered protocol family 1
> RPC: Registered named UNIX socket transport module.
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> RPC: Registered tcp NFSv4.1 backchannel transport module.
> imx rpmsg driver is registered.
> Bus freq driver module loaded
> futex hash table entries: 512 (order: 3, 32768 bytes)
> VFS: Disk quotas dquot_6.6.0
> VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> NFS: Registering the id_resolver key type
> Key type id_resolver registered
> Key type id_legacy registered
> jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
> fuse init (API version 7.23)
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> backlight supply power not found, using dummy regulator
> MIPI DSI driver module loaded
> MIPI DSI driver module loaded
> sii902x 2-0039: No reset pin found
> sii902x 2-0039: Can not read edid
> 30730000.lcdif supply lcd not found, using dummy regulator
> mxsfb 30730000.lcdif: failed to find mxc display driver
> Console: switching to colour frame buffer device 60x34
> mxsfb 30730000.lcdif: initialized
> imx-sdma 30bd0000.sdma: no event needs to be remapped
> imx-sdma 30bd0000.sdma: loaded firmware 4.2
> imx-sdma 30bd0000.sdma: initialized
> pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1
> pfuze100-regulator 0-0008: FAB: 0, FIN: 0
> pfuze100-regulator 0-0008: pfuze3000 found.
> 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 279, base_baud =
> 1500000) is a IMX
> console [ttymxc0] enabled
> 30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 288, base_baud =
> 5000000) is a IMX
> 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 289, base_baud =
> 5000000) is a IMX
> imx sema4 driver is registered.
> [drm] Initialized drm 1.1.0 20060810
> [drm] Initialized vivante 1.0.0 20120216 on minor 0
> brd: module loaded
> loop: module loaded
> input: fxos8700 as
>
> /devices/platform/soc/30800000.aips-bus/30a30000.i2c/i2c-1/1-001e/input/input0
> fxos8700 device driver probe successfully
> input: fxas2100x as
>
> /devices/platform/soc/30800000.aips-bus/30a30000.i2c/i2c-1/1-0020/input/input1
> fxas2100x 1-0020: fxas2100x device driver probe successfully
> spi_gpio spi4: gpio-miso property not found, switching to no-rx mode
> spi_imx 30840000.ecspi: probed
> CAN device driver interface
> flexcan 30a10000.can: device registered (reg_base=f5a10000, irq=283)
> 30be0000.ethernet supply phy not found, using dummy regulator
> pps pps0: new PPS source ptp0
> libphy: fec_enet_mii_bus: probed
> fec 30be0000.ethernet eth0: registered PHC device 0
> 30bf0000.ethernet supply phy not found, using dummy regulator
> pps pps1: new PPS source ptp1
> fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Invalid
> MAC address: 00:00:00:00:00:00
> fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Using
> random MAC address: 46:cb:dc:d0:f3:e4
> fec 30bf0000.ethernet eth1: registered PHC device 1
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci-mxc: Freescale On-Chip EHCI Host driver
> usbcore: registered new interface driver usb-storage
> usbcore: registered new interface driver usb_ehset_test
> 30b10200.usbmisc supply vbus-wakeup not found, using dummy regulator
> 30b20200.usbmisc supply vbus-wakeup not found, using dummy regulator
> 30b30200.usbmisc supply vbus-wakeup not found, using dummy regulator
> ci_hdrc ci_hdrc.1: EHCI Host Controller
> ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
> ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> mousedev: PS/2 mouse device common for all mice
> input: 30370000.snvs:snvs-powerkey as
>
> /devices/platform/soc/30000000.aips-bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input2
> spi2.0 supply vcc not found, using dummy regulator
> ads7846 spi2.0: touchscreen, irq 88
> input: ADS7846 Touchscreen as
>
> /devices/platform/soc/30800000.aips-bus/30800000.spba-bus/30840000.ecspi/spi_master/spi2/spi2.0/input/input3
> read mpl3115 chip id 0xc4
> input: mpl3115 as /devices/virtual/input/input4
> mpl3115 device driver probe successfully
> snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
> 30370000.snvs:snvs- as rtc0
> i2c /dev entries driver
> IR NEC protocol handler initialized
> IR RC5(x/sz) protocol handler initialized
> IR RC6 protocol handler initialized
> IR JVC protocol handler initialized
> IR Sony protocol handler initialized
> IR SANYO protocol handler initialized
> IR Sharp protocol handler initialized
> IR MCE Keyboard/mouse protocol handler initialized
> IR XMP protocol handler initialized
> pxp-v4l2 pxp_v4l2_out: initialized
> imx2-wdt 30280000.wdog: use WDOG_B to reboot.
> imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
> Bluetooth: HCI UART driver ver 2.3
> Bluetooth: HCI UART protocol H4 registered
> Bluetooth: HCI UART protocol BCSP registered
> Bluetooth: HCI UART protocol ATH3K registered
> usbcore: registered new interface driver bcm203x
> usbcore: registered new interface driver btusb
> usbcore: registered new interface driver ath3k
> sdhci: Secure Digital Host Controller Interface driver
> sdhci: Copyright(c) Pierre Ossman
> sdhci-pltfm: SDHCI platform and OF driver helper
> /soc/aips-bus@30800000/usdhc@30b40000: voltage-ranges unspecified
> sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO
> sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO
> sdhci-esdhc-imx 30b40000.usdhc: No vqmmc regulator found
> mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA
> /soc/aips-bus@30800000/usdhc@30b50000: voltage-ranges unspecified
> sdhci-esdhc-imx 30b50000.usdhc: assigned as wifi host
> sdhci-esdhc-imx 30b50000.usdhc: No vmmc regulator found
> sdhci-esdhc-imx 30b50000.usdhc: No vqmmc regulator found
> mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA
> /soc/aips-bus@30800000/usdhc@30b60000: voltage-ranges unspecified
> sdhci-esdhc-imx 30b60000.usdhc: No vmmc regulator found
> sdhci-esdhc-imx 30b60000.usdhc: No vqmmc regulator found
> mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA
> caam 30900000.caam: Entropy delay = 3200
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 3600
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 4000
> mmc0: Problem setting current limit!
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 4400
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 4800
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 5200
> mmc0: new ultra high speed DDR50 SDHC card at address e624
> mmcblk0: mmc0:e624 SU08G 7.40 GiB
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 5600
> mmcblk0: p1 p2
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 6000
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 6400
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 6800
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 7200
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 7600
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 8000
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 8400
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 8800
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 9200
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 9600
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 10000
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 10400
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 10800
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 11200
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 11600
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 12000
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: Entropy delay = 12400
> caam 30900000.caam: failed to acquire DECO 0
> caam 30900000.caam: failed to instantiate RNG
> ------------[ cut here ]------------
> WARNING: CPU: 0 PID: 1 at
>
> /home/fsl/Data/fsl_yocto_community_krogoth/build_imx7sdb_qt_x11/tmp/work-shared/imx7dsabresd/kernel-source/mm/vmalloc.c:1465
> caam_remove+0x6c/0x408()
> Trying to vfree() nonexistent vm area (a8063000)
> Modules linked in:
> CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.1.15-1.1.0+ga4d2a08 #1
> Hardware name: Freescale i.MX7 Dual (Device Tree)
> [<80015d78>] (unwind_backtrace) from [<8001271c>] (show_stack+0x10/0x14)
> [<8001271c>] (show_stack) from [<80790280>] (dump_stack+0x84/0xc4)
> [<80790280>] (dump_stack) from [<80034750>]
> (warn_slowpath_common+0x80/0xb0)
> [<80034750>] (warn_slowpath_common) from [<800347b0>]
> (warn_slowpath_fmt+0x30/0x40)
> [<800347b0>] (warn_slowpath_fmt) from [<8056ed9c>] (caam_remove+0x6c/0x408)
> [<8056ed9c>] (caam_remove) from [<8056ff10>] (caam_probe+0xdd8/0xf10)
> [<8056ff10>] (caam_probe) from [<80381118>] (platform_drv_probe+0x44/0xac)
> [<80381118>] (platform_drv_probe) from [<8037f9b4>]
> (driver_probe_device+0x174/0x2b4)
> [<8037f9b4>] (driver_probe_device) from [<8037fbc4>]
> (__driver_attach+0x8c/0x90)
> [<8037fbc4>] (__driver_attach) from [<8037e040>]
> (bus_for_each_dev+0x68/0x9c)
> [<8037e040>] (bus_for_each_dev) from [<8037f144>]
> (bus_add_driver+0x148/0x1f0)
> [<8037f144>] (bus_add_driver) from [<803801c4>] (driver_register+0x78/0xf8)
> [<803801c4>] (driver_register) from [<80009718>]
> (do_one_initcall+0x8c/0x1d4)
> [<80009718>] (do_one_initcall) from [<80a8fdbc>]
> (kernel_init_freeable+0x144/0x1e4)
> [<80a8fdbc>] (kernel_init_freeable) from [<8078c4e4>]
> (kernel_init+0x8/0xe8)
> [<8078c4e4>] (kernel_init) from [<8000f528>] (ret_from_fork+0x14/0x2c)
> ---[ end trace 0315279c11aaddc3 ]---
> caam: probe of 30900000.caam failed with error -11
> Unable to handle kernel NULL pointer dereference at virtual address
> 00000004
> pgd = 80004000
> [00000004] *pgd=00000000
> Internal error: Oops: 805 [#1] PREEMPT SMP ARM
> Modules linked in:
> CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
> 4.1.15-1.1.0+ga4d2a08 #1
> Hardware name: Freescale i.MX7 Dual (Device Tree)
> task: a807c000 ti: a8062000 task.ti: a8062000
> PC is at caam_sm_startup+0x8c/0x3cc
> LR is at device_add+0x154/0x56c
> pc : [<8057f910>] lr : [<8037d008>] psr: a0000113
> sp : a8063ed0 ip : 00000000 fp : 00000000
> r10: 80af358c r9 : 00000000 r8 : 00000000
> r7 : 80ad15d8 r6 : ab73bac4 r5 : a8150010 r4 : a8419840
> r3 : a8493210 r2 : a8493200 r1 : 00000000 r0 : a8493200
> Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
> Control: 10c53c7d Table: 8000406a DAC: 00000015
> Process swapper/0 (pid: 1, stack limit = 0xa8062210)
> Stack: (0xa8063ed0 to 0xa8064000)
> 3ec0: 00000000 80796214 a8063ee8
> a8493200
> 3ee0: a8150010 80aff720 80aff720 a847e1c0 80ad15d8 00000000 80ae6bcc
> 80af358c
> 3f00: 00000000 80ad1628 80aff720 80009718 80ae6ba8 8013f8ac 00000000
> a80ee380
> 3f20: 00000000 80b073e8 60000113 00000000 abfffb76 abfffb74 807c2a24
> 8004c4d4
> 3f40: 00000000 809d7a40 00000006 00000006 80b073d0 0000010d 00000006
> 80b66000
> 3f60: 0000010d 00000006 80b66000 80b66000 80ae6bc4 80a8fdbc 00000006
> 00000006
> 3f80: 80a8f594 80050b94 00000000 8078c4dc 00000000 00000000 00000000
> 00000000
> 3fa0: 00000000 8078c4e4 00000000 8000f528 00000000 00000000 00000000
> 00000000
> 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> 00000000
> 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 2fef7abf
> cbabedc9
> [<8057f910>] (caam_sm_startup) from [<80ad1628>] (caam_sm_init+0x50/0x58)
> [<80ad1628>] (caam_sm_init) from [<80009718>] (do_one_initcall+0x8c/0x1d4)
> [<80009718>] (do_one_initcall) from [<80a8fdbc>]
> (kernel_init_freeable+0x144/0x1e4)
> [<80a8fdbc>] (kernel_init_freeable) from [<8078c4e4>]
> (kernel_init+0x8/0xe8)
> [<8078c4e4>] (kernel_init) from [<8000f528>] (ret_from_fork+0x14/0x2c)
> Code: e59d200c e2823010 e5842008 e5824068 (e5893004)
> ---[ end trace 0315279c11aaddc4 ]---
> Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
>
> ---[ end Kernel panic - not syncing: Attempted to kill init!
> exitcode=0x0000000b
> --
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>
[-- Attachment #2: Type: text/html, Size: 21209 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: master/krogoth kernel crash for imx7D
2016-06-23 18:09 ` Gary Bisson
@ 2016-06-24 11:56 ` Daiane Angolini
0 siblings, 0 replies; 5+ messages in thread
From: Daiane Angolini @ 2016-06-24 11:56 UTC (permalink / raw)
To: Gary Bisson; +Cc: meta-freescale
On Thu, Jun 23, 2016 at 3:09 PM, Gary Bisson
<gary.bisson@boundarydevices.com> wrote:
> Hi Daiane,
>
> I've had this CAAM issue in the past:
> http://lists.denx.de/pipermail/u-boot/2016-March/250112.html
>
> Are you using mainline U-Boot? If so you need to enable the secure mode,
> otherwise CAAM won't work. See the patch I made on our Github repo to fix
> it:
> https://github.com/boundarydevices/u-boot-imx6/commit/38b5fa7e
Thanks for the suggestion. I'm going to test and let you know.
Daiane
>
> Regards,
> Gary
>
> On Thu, Jun 23, 2016 at 7:10 PM, Daiane Angolini <daiane.list@gmail.com>
> wrote:
>>
>> I'm facing the following kernel crash for imx7dsabresd. Any hint?
>>
>> Starting kernel ...
>>
>> Booting Linux on physical CPU 0x0
>> Linux version 4.1.15-1.1.0+ga4d2a08 (fsl@fsl-Precision-M4800) (gcc
>> version 5.3.0 (GCC) ) #1 SMP PREEMPT Thu Jun 23 15:50:23 CEST 2016
>> CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
>> CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
>> Machine model: Freescale i.MX7D SabreSD Board
>> Reserved memory: created CMA memory pool at 0xac000000, size 320 MiB
>> Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
>> Memory policy: Data cache writealloc
>> PERCPU: Embedded 12 pages/cpu @ab71c000 s16908 r8192 d24052 u49152
>> Built 1 zonelists in Zone order, mobility grouping on. Total pages:
>> 260096
>> Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait
>> rw
>> PID hash table entries: 4096 (order: 2, 16384 bytes)
>> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>> Memory: 698868K/1048576K available (7944K kernel code, 422K rwdata,
>> 2832K rodata, 428K init, 440K bss, 22028K reserved, 327680K
>> cma-reserved, 0K highmem)
>> Virtual kernel memory layout:
>> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
>> fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
>> vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
>> lowmem : 0x80000000 - 0xc0000000 (1024 MB)
>> pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
>> modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
>> .text : 0x80008000 - 0x80a8e398 (10777 kB)
>> .init : 0x80a8f000 - 0x80afa000 ( 428 kB)
>> .data : 0x80afa000 - 0x80b63b40 ( 423 kB)
>> .bss : 0x80b66000 - 0x80bd40c0 ( 441 kB)
>> SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
>> Preemptible hierarchical RCU implementation.
>> Additional per-CPU info printed with stalls.
>> RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
>> RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
>> NR_IRQS:16 nr_irqs:16 16
>> Architected cp15 timer(s) running at 8.00MHz (phys).
>> clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles:
>> 0x1d854df40, max_idle_ns: 440795202120 ns
>> sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every
>> 2199023255500ns
>> Switching to timer-based delay loop, resolution 125ns
>> mxc_clocksource_init 3000000
>> Ignoring duplicate/late registration of read_current_timer delay
>> clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff,
>> max_idle_ns: 637086815595 ns
>> Console: colour dummy device 80x30
>> Calibrating delay loop (skipped), value calculated using timer
>> frequency.. 16.00 BogoMIPS (lpj=80000)
>> pid_max: default: 32768 minimum: 301
>> Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
>> Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
>> CPU: Testing write buffer coherency: ok
>> /cpus/cpu@0 missing clock-frequency property
>> /cpus/cpu@1 missing clock-frequency property
>> CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
>> Setting up static identity map for 0x80008280 - 0x800082d8
>> CPU1: failed to come online
>> Brought up 1 CPUs
>> SMP: Total of 1 processors activated (16.00 BogoMIPS).
>> CPU: All CPU(s) started in SVC mode.
>> devtmpfs: initialized
>> device-tree: Duplicate name in lcdif@30730000, renamed to "display#1"
>> VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
>> clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
>> max_idle_ns: 19112604462750000 ns
>> pinctrl core: initialized pinctrl subsystem
>> NET: Registered protocol family 16
>> DMA: preallocated 256 KiB pool for atomic coherent allocations
>> cpuidle: using governor ladder
>> cpuidle: using governor menu
>> DDR type is DDR3!
>> hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint
>> registers.
>> hw-breakpoint: maximum watchpoint size is 8 bytes.
>> imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
>> imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver
>> MU is ready for cross core communication!
>> mxs-dma 33000000.dma-apbh: initialized
>> SCSI subsystem initialized
>> usbcore: registered new interface driver usbfs
>> usbcore: registered new interface driver hub
>> usbcore: registered new device driver usb
>> 30800000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
>> 30800000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator
>> i2c i2c-0: IMX I2C adapter registered
>> i2c i2c-0: can't use DMA
>> i2c i2c-1: IMX I2C adapter registered
>> i2c i2c-1: can't use DMA
>> i2c i2c-2: IMX I2C adapter registered
>> i2c i2c-2: can't use DMA
>> i2c i2c-3: IMX I2C adapter registered
>> i2c i2c-3: can't use DMA
>> Linux video capture interface: v2.00
>> pps_core: LinuxPPS API ver. 1 registered
>> pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
>> <giometti@linux.it>
>> PTP clock support registered
>> MIPI CSI2 driver module loaded
>> Advanced Linux Sound Architecture Driver Initialized.
>> Bluetooth: Core ver 2.20
>> NET: Registered protocol family 31
>> Bluetooth: HCI device and connection manager initialized
>> Bluetooth: HCI socket layer initialized
>> Bluetooth: L2CAP socket layer initialized
>> Bluetooth: SCO socket layer initialized
>> Switched to clocksource arch_sys_counter
>> NET: Registered protocol family 2
>> TCP established hash table entries: 8192 (order: 3, 32768 bytes)
>> TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
>> TCP: Hash tables configured (established 8192 bind 8192)
>> UDP hash table entries: 512 (order: 2, 16384 bytes)
>> UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
>> NET: Registered protocol family 1
>> RPC: Registered named UNIX socket transport module.
>> RPC: Registered udp transport module.
>> RPC: Registered tcp transport module.
>> RPC: Registered tcp NFSv4.1 backchannel transport module.
>> imx rpmsg driver is registered.
>> Bus freq driver module loaded
>> futex hash table entries: 512 (order: 3, 32768 bytes)
>> VFS: Disk quotas dquot_6.6.0
>> VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>> NFS: Registering the id_resolver key type
>> Key type id_resolver registered
>> Key type id_legacy registered
>> jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
>> fuse init (API version 7.23)
>> io scheduler noop registered
>> io scheduler deadline registered
>> io scheduler cfq registered (default)
>> backlight supply power not found, using dummy regulator
>> MIPI DSI driver module loaded
>> MIPI DSI driver module loaded
>> sii902x 2-0039: No reset pin found
>> sii902x 2-0039: Can not read edid
>> 30730000.lcdif supply lcd not found, using dummy regulator
>> mxsfb 30730000.lcdif: failed to find mxc display driver
>> Console: switching to colour frame buffer device 60x34
>> mxsfb 30730000.lcdif: initialized
>> imx-sdma 30bd0000.sdma: no event needs to be remapped
>> imx-sdma 30bd0000.sdma: loaded firmware 4.2
>> imx-sdma 30bd0000.sdma: initialized
>> pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1
>> pfuze100-regulator 0-0008: FAB: 0, FIN: 0
>> pfuze100-regulator 0-0008: pfuze3000 found.
>> 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 279, base_baud =
>> 1500000) is a IMX
>> console [ttymxc0] enabled
>> 30a70000.serial: ttymxc4 at MMIO 0x30a70000 (irq = 288, base_baud =
>> 5000000) is a IMX
>> 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 289, base_baud =
>> 5000000) is a IMX
>> imx sema4 driver is registered.
>> [drm] Initialized drm 1.1.0 20060810
>> [drm] Initialized vivante 1.0.0 20120216 on minor 0
>> brd: module loaded
>> loop: module loaded
>> input: fxos8700 as
>>
>> /devices/platform/soc/30800000.aips-bus/30a30000.i2c/i2c-1/1-001e/input/input0
>> fxos8700 device driver probe successfully
>> input: fxas2100x as
>>
>> /devices/platform/soc/30800000.aips-bus/30a30000.i2c/i2c-1/1-0020/input/input1
>> fxas2100x 1-0020: fxas2100x device driver probe successfully
>> spi_gpio spi4: gpio-miso property not found, switching to no-rx mode
>> spi_imx 30840000.ecspi: probed
>> CAN device driver interface
>> flexcan 30a10000.can: device registered (reg_base=f5a10000, irq=283)
>> 30be0000.ethernet supply phy not found, using dummy regulator
>> pps pps0: new PPS source ptp0
>> libphy: fec_enet_mii_bus: probed
>> fec 30be0000.ethernet eth0: registered PHC device 0
>> 30bf0000.ethernet supply phy not found, using dummy regulator
>> pps pps1: new PPS source ptp1
>> fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Invalid
>> MAC address: 00:00:00:00:00:00
>> fec 30bf0000.ethernet (unnamed net_device) (uninitialized): Using
>> random MAC address: 46:cb:dc:d0:f3:e4
>> fec 30bf0000.ethernet eth1: registered PHC device 1
>> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> ehci-mxc: Freescale On-Chip EHCI Host driver
>> usbcore: registered new interface driver usb-storage
>> usbcore: registered new interface driver usb_ehset_test
>> 30b10200.usbmisc supply vbus-wakeup not found, using dummy regulator
>> 30b20200.usbmisc supply vbus-wakeup not found, using dummy regulator
>> 30b30200.usbmisc supply vbus-wakeup not found, using dummy regulator
>> ci_hdrc ci_hdrc.1: EHCI Host Controller
>> ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
>> ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
>> hub 1-0:1.0: USB hub found
>> hub 1-0:1.0: 1 port detected
>> mousedev: PS/2 mouse device common for all mice
>> input: 30370000.snvs:snvs-powerkey as
>>
>> /devices/platform/soc/30000000.aips-bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input2
>> spi2.0 supply vcc not found, using dummy regulator
>> ads7846 spi2.0: touchscreen, irq 88
>> input: ADS7846 Touchscreen as
>>
>> /devices/platform/soc/30800000.aips-bus/30800000.spba-bus/30840000.ecspi/spi_master/spi2/spi2.0/input/input3
>> read mpl3115 chip id 0xc4
>> input: mpl3115 as /devices/virtual/input/input4
>> mpl3115 device driver probe successfully
>> snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
>> 30370000.snvs:snvs- as rtc0
>> i2c /dev entries driver
>> IR NEC protocol handler initialized
>> IR RC5(x/sz) protocol handler initialized
>> IR RC6 protocol handler initialized
>> IR JVC protocol handler initialized
>> IR Sony protocol handler initialized
>> IR SANYO protocol handler initialized
>> IR Sharp protocol handler initialized
>> IR MCE Keyboard/mouse protocol handler initialized
>> IR XMP protocol handler initialized
>> pxp-v4l2 pxp_v4l2_out: initialized
>> imx2-wdt 30280000.wdog: use WDOG_B to reboot.
>> imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
>> Bluetooth: HCI UART driver ver 2.3
>> Bluetooth: HCI UART protocol H4 registered
>> Bluetooth: HCI UART protocol BCSP registered
>> Bluetooth: HCI UART protocol ATH3K registered
>> usbcore: registered new interface driver bcm203x
>> usbcore: registered new interface driver btusb
>> usbcore: registered new interface driver ath3k
>> sdhci: Secure Digital Host Controller Interface driver
>> sdhci: Copyright(c) Pierre Ossman
>> sdhci-pltfm: SDHCI platform and OF driver helper
>> /soc/aips-bus@30800000/usdhc@30b40000: voltage-ranges unspecified
>> sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO
>> sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO
>> sdhci-esdhc-imx 30b40000.usdhc: No vqmmc regulator found
>> mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA
>> /soc/aips-bus@30800000/usdhc@30b50000: voltage-ranges unspecified
>> sdhci-esdhc-imx 30b50000.usdhc: assigned as wifi host
>> sdhci-esdhc-imx 30b50000.usdhc: No vmmc regulator found
>> sdhci-esdhc-imx 30b50000.usdhc: No vqmmc regulator found
>> mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA
>> /soc/aips-bus@30800000/usdhc@30b60000: voltage-ranges unspecified
>> sdhci-esdhc-imx 30b60000.usdhc: No vmmc regulator found
>> sdhci-esdhc-imx 30b60000.usdhc: No vqmmc regulator found
>> mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA
>> caam 30900000.caam: Entropy delay = 3200
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 3600
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 4000
>> mmc0: Problem setting current limit!
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 4400
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 4800
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 5200
>> mmc0: new ultra high speed DDR50 SDHC card at address e624
>> mmcblk0: mmc0:e624 SU08G 7.40 GiB
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 5600
>> mmcblk0: p1 p2
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 6000
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 6400
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 6800
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 7200
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 7600
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 8000
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 8400
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 8800
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 9200
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 9600
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 10000
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 10400
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 10800
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 11200
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 11600
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 12000
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: Entropy delay = 12400
>> caam 30900000.caam: failed to acquire DECO 0
>> caam 30900000.caam: failed to instantiate RNG
>> ------------[ cut here ]------------
>> WARNING: CPU: 0 PID: 1 at
>>
>> /home/fsl/Data/fsl_yocto_community_krogoth/build_imx7sdb_qt_x11/tmp/work-shared/imx7dsabresd/kernel-source/mm/vmalloc.c:1465
>> caam_remove+0x6c/0x408()
>> Trying to vfree() nonexistent vm area (a8063000)
>> Modules linked in:
>> CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.1.15-1.1.0+ga4d2a08 #1
>> Hardware name: Freescale i.MX7 Dual (Device Tree)
>> [<80015d78>] (unwind_backtrace) from [<8001271c>] (show_stack+0x10/0x14)
>> [<8001271c>] (show_stack) from [<80790280>] (dump_stack+0x84/0xc4)
>> [<80790280>] (dump_stack) from [<80034750>]
>> (warn_slowpath_common+0x80/0xb0)
>> [<80034750>] (warn_slowpath_common) from [<800347b0>]
>> (warn_slowpath_fmt+0x30/0x40)
>> [<800347b0>] (warn_slowpath_fmt) from [<8056ed9c>]
>> (caam_remove+0x6c/0x408)
>> [<8056ed9c>] (caam_remove) from [<8056ff10>] (caam_probe+0xdd8/0xf10)
>> [<8056ff10>] (caam_probe) from [<80381118>] (platform_drv_probe+0x44/0xac)
>> [<80381118>] (platform_drv_probe) from [<8037f9b4>]
>> (driver_probe_device+0x174/0x2b4)
>> [<8037f9b4>] (driver_probe_device) from [<8037fbc4>]
>> (__driver_attach+0x8c/0x90)
>> [<8037fbc4>] (__driver_attach) from [<8037e040>]
>> (bus_for_each_dev+0x68/0x9c)
>> [<8037e040>] (bus_for_each_dev) from [<8037f144>]
>> (bus_add_driver+0x148/0x1f0)
>> [<8037f144>] (bus_add_driver) from [<803801c4>]
>> (driver_register+0x78/0xf8)
>> [<803801c4>] (driver_register) from [<80009718>]
>> (do_one_initcall+0x8c/0x1d4)
>> [<80009718>] (do_one_initcall) from [<80a8fdbc>]
>> (kernel_init_freeable+0x144/0x1e4)
>> [<80a8fdbc>] (kernel_init_freeable) from [<8078c4e4>]
>> (kernel_init+0x8/0xe8)
>> [<8078c4e4>] (kernel_init) from [<8000f528>] (ret_from_fork+0x14/0x2c)
>> ---[ end trace 0315279c11aaddc3 ]---
>> caam: probe of 30900000.caam failed with error -11
>> Unable to handle kernel NULL pointer dereference at virtual address
>> 00000004
>> pgd = 80004000
>> [00000004] *pgd=00000000
>> Internal error: Oops: 805 [#1] PREEMPT SMP ARM
>> Modules linked in:
>> CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
>> 4.1.15-1.1.0+ga4d2a08 #1
>> Hardware name: Freescale i.MX7 Dual (Device Tree)
>> task: a807c000 ti: a8062000 task.ti: a8062000
>> PC is at caam_sm_startup+0x8c/0x3cc
>> LR is at device_add+0x154/0x56c
>> pc : [<8057f910>] lr : [<8037d008>] psr: a0000113
>> sp : a8063ed0 ip : 00000000 fp : 00000000
>> r10: 80af358c r9 : 00000000 r8 : 00000000
>> r7 : 80ad15d8 r6 : ab73bac4 r5 : a8150010 r4 : a8419840
>> r3 : a8493210 r2 : a8493200 r1 : 00000000 r0 : a8493200
>> Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
>> Control: 10c53c7d Table: 8000406a DAC: 00000015
>> Process swapper/0 (pid: 1, stack limit = 0xa8062210)
>> Stack: (0xa8063ed0 to 0xa8064000)
>> 3ec0: 00000000 80796214 a8063ee8
>> a8493200
>> 3ee0: a8150010 80aff720 80aff720 a847e1c0 80ad15d8 00000000 80ae6bcc
>> 80af358c
>> 3f00: 00000000 80ad1628 80aff720 80009718 80ae6ba8 8013f8ac 00000000
>> a80ee380
>> 3f20: 00000000 80b073e8 60000113 00000000 abfffb76 abfffb74 807c2a24
>> 8004c4d4
>> 3f40: 00000000 809d7a40 00000006 00000006 80b073d0 0000010d 00000006
>> 80b66000
>> 3f60: 0000010d 00000006 80b66000 80b66000 80ae6bc4 80a8fdbc 00000006
>> 00000006
>> 3f80: 80a8f594 80050b94 00000000 8078c4dc 00000000 00000000 00000000
>> 00000000
>> 3fa0: 00000000 8078c4e4 00000000 8000f528 00000000 00000000 00000000
>> 00000000
>> 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
>> 00000000
>> 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 2fef7abf
>> cbabedc9
>> [<8057f910>] (caam_sm_startup) from [<80ad1628>] (caam_sm_init+0x50/0x58)
>> [<80ad1628>] (caam_sm_init) from [<80009718>] (do_one_initcall+0x8c/0x1d4)
>> [<80009718>] (do_one_initcall) from [<80a8fdbc>]
>> (kernel_init_freeable+0x144/0x1e4)
>> [<80a8fdbc>] (kernel_init_freeable) from [<8078c4e4>]
>> (kernel_init+0x8/0xe8)
>> [<8078c4e4>] (kernel_init) from [<8000f528>] (ret_from_fork+0x14/0x2c)
>> Code: e59d200c e2823010 e5842008 e5824068 (e5893004)
>> ---[ end trace 0315279c11aaddc4 ]---
>> Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
>>
>> ---[ end Kernel panic - not syncing: Attempted to kill init!
>> exitcode=0x0000000b
>> --
>> _______________________________________________
>> meta-freescale mailing list
>> meta-freescale@yoctoproject.org
>> https://lists.yoctoproject.org/listinfo/meta-freescale
>
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: master/krogoth kernel crash for imx7D
2016-06-23 17:10 master/krogoth kernel crash for imx7D Daiane Angolini
2016-06-23 18:09 ` Gary Bisson
@ 2016-07-11 12:22 ` Fabio Estevam
2016-07-11 14:30 ` Otavio Salvador
1 sibling, 1 reply; 5+ messages in thread
From: Fabio Estevam @ 2016-07-11 12:22 UTC (permalink / raw)
To: Daiane Angolini; +Cc: meta-freescale
Hi Daiane,
On Thu, Jun 23, 2016 at 2:10 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
> I'm facing the following kernel crash for imx7dsabresd. Any hint?
These two patches fix this issue:
http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commit;h=a7e938f3cd19195cd94ed0a815c9de44a7e0204a
http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commit;h=6a5fe0fbd14a4c138ad98837d350cda54583cd64
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: master/krogoth kernel crash for imx7D
2016-07-11 12:22 ` Fabio Estevam
@ 2016-07-11 14:30 ` Otavio Salvador
0 siblings, 0 replies; 5+ messages in thread
From: Otavio Salvador @ 2016-07-11 14:30 UTC (permalink / raw)
To: Fabio Estevam; +Cc: meta-freescale
On Mon, Jul 11, 2016 at 9:22 AM, Fabio Estevam <festevam@gmail.com> wrote:
> Hi Daiane,
>
> On Thu, Jun 23, 2016 at 2:10 PM, Daiane Angolini <daiane.list@gmail.com> wrote:
>> I'm facing the following kernel crash for imx7dsabresd. Any hint?
>
> These two patches fix this issue:
>
> http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commit;h=a7e938f3cd19195cd94ed0a815c9de44a7e0204a
>
> http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commit;h=6a5fe0fbd14a4c138ad98837d350cda54583cd64
We backported those for the 2016.05 branch and bumped the recipe; all fine now.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2016-07-11 14:30 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-23 17:10 master/krogoth kernel crash for imx7D Daiane Angolini
2016-06-23 18:09 ` Gary Bisson
2016-06-24 11:56 ` Daiane Angolini
2016-07-11 12:22 ` Fabio Estevam
2016-07-11 14:30 ` Otavio Salvador
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.