* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion @ 2019-12-06 16:24 Igor Opaniuk 2019-12-06 16:39 ` Igor Opaniuk 2019-12-28 10:48 ` sbabic at denx.de 0 siblings, 2 replies; 7+ messages in thread From: Igor Opaniuk @ 2019-12-06 16:24 UTC (permalink / raw) To: u-boot From: Igor Opaniuk <igor.opaniuk@toradex.com> Not all CONFIG_FSL_ESDHC defines were properly replaced with CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on Colibri iMX6 SoMs. U-boot is stuck after this message: Commercial temperature grade DDR3 timings, 64bit bus width. Trying to boot from MMC1 Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> --- board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/board/toradex/colibri_imx6/colibri_imx6.c b/board/toradex/colibri_imx6/colibri_imx6.c index ad40b589c1..44173dde1f 100644 --- a/board/toradex/colibri_imx6/colibri_imx6.c +++ b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@ iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) /* Colibri MMC */ iomux_v3_cfg_t const usdhc1_pads[] = { MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) } #endif -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) /* use the following sequence: eMMC, MMC */ struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { {USDHC3_BASE_ADDR}, -- 2.17.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion 2019-12-06 16:24 [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion Igor Opaniuk @ 2019-12-06 16:39 ` Igor Opaniuk 2019-12-06 17:23 ` Lukasz Majewski 2019-12-28 10:48 ` sbabic at denx.de 1 sibling, 1 reply; 7+ messages in thread From: Igor Opaniuk @ 2019-12-06 16:39 UTC (permalink / raw) To: u-boot Hi Stefano On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk@gmail.com> wrote: > > From: Igor Opaniuk <igor.opaniuk@toradex.com> > > Not all CONFIG_FSL_ESDHC defines were properly replaced with > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > Colibri iMX6 SoMs. > > U-boot is stuck after this message: > Commercial temperature grade DDR3 timings, 64bit bus width. > Trying to boot from MMC1 > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> > --- > > board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c b/board/toradex/colibri_imx6/colibri_imx6.c > index ad40b589c1..44173dde1f 100644 > --- a/board/toradex/colibri_imx6/colibri_imx6.c > +++ b/board/toradex/colibri_imx6/colibri_imx6.c > @@ -83,7 +83,7 @@ iomux_v3_cfg_t const uart1_pads[] = { > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), > }; > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > /* Colibri MMC */ > iomux_v3_cfg_t const usdhc1_pads[] = { > MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) > } > #endif > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > /* use the following sequence: eMMC, MMC */ > struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { > {USDHC3_BASE_ADDR}, > -- > 2.17.1 > I've just found the same fix [1] but from Ricardo with Awaiting upstream status in patchwork (I thought that he has fixed just Apalis iMX6), but seems the patch was lost somewhere, as I can not find it nor in u-boot-imx/next neither in u-boot-imx/master branches. [1] https://patchwork.ozlabs.org/patch/1157059/ -- Best regards - Freundliche Grüsse - Meilleures salutations Senior Development Engineer, Igor Opaniuk Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48 00 (main line) ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion 2019-12-06 16:39 ` Igor Opaniuk @ 2019-12-06 17:23 ` Lukasz Majewski 2019-12-06 18:59 ` Tom Rini 0 siblings, 1 reply; 7+ messages in thread From: Lukasz Majewski @ 2019-12-06 17:23 UTC (permalink / raw) To: u-boot Hi Igor, > Hi Stefano > > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk@gmail.com> > wrote: > > > > From: Igor Opaniuk <igor.opaniuk@toradex.com> > > > > Not all CONFIG_FSL_ESDHC defines were properly replaced with > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > > Colibri iMX6 SoMs. > > > > U-boot is stuck after this message: > > Commercial temperature grade DDR3 timings, 64bit bus width. > > Trying to boot from MMC1 > > > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> > > --- > > > > board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c > > b/board/toradex/colibri_imx6/colibri_imx6.c index > > ad40b589c1..44173dde1f 100644 --- > > a/board/toradex/colibri_imx6/colibri_imx6.c +++ > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@ > > iomux_v3_cfg_t const uart1_pads[] = { > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > /* Colibri MMC */ > > iomux_v3_cfg_t const usdhc1_pads[] = { > > MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) > > } > > #endif > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > /* use the following sequence: eMMC, MMC */ > > struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { > > {USDHC3_BASE_ADDR}, > > -- > > 2.17.1 > > > > I've just found the same fix [1] but from Ricardo with Awaiting > upstream status in patchwork (I thought that he has fixed just Apalis > iMX6), but seems the patch was > lost somewhere, as I can not find it nor in u-boot-imx/next neither > in u-boot-imx/master branches. Thanks for providing the fix (at least for the Toradex boards) And I do guess that more i.MX6 boards are affected ... > > [1] https://patchwork.ozlabs.org/patch/1157059/ > Best regards, Lukasz Majewski -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 488 bytes Desc: OpenPGP digital signature URL: <https://lists.denx.de/pipermail/u-boot/attachments/20191206/34477b39/attachment.sig> ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion 2019-12-06 17:23 ` Lukasz Majewski @ 2019-12-06 18:59 ` Tom Rini 2019-12-09 15:03 ` Oliver Graute 0 siblings, 1 reply; 7+ messages in thread From: Tom Rini @ 2019-12-06 18:59 UTC (permalink / raw) To: u-boot On Fri, Dec 06, 2019 at 06:23:09PM +0100, Lukasz Majewski wrote: > Hi Igor, > > > Hi Stefano > > > > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk@gmail.com> > > wrote: > > > > > > From: Igor Opaniuk <igor.opaniuk@toradex.com> > > > > > > Not all CONFIG_FSL_ESDHC defines were properly replaced with > > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > > > Colibri iMX6 SoMs. > > > > > > U-boot is stuck after this message: > > > Commercial temperature grade DDR3 timings, 64bit bus width. > > > Trying to boot from MMC1 > > > > > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > > > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> > > > --- > > > > > > board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c > > > b/board/toradex/colibri_imx6/colibri_imx6.c index > > > ad40b589c1..44173dde1f 100644 --- > > > a/board/toradex/colibri_imx6/colibri_imx6.c +++ > > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@ > > > iomux_v3_cfg_t const uart1_pads[] = { > > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > /* Colibri MMC */ > > > iomux_v3_cfg_t const usdhc1_pads[] = { > > > MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) > > > } > > > #endif > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > /* use the following sequence: eMMC, MMC */ > > > struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { > > > {USDHC3_BASE_ADDR}, > > > -- > > > 2.17.1 > > > > > > > I've just found the same fix [1] but from Ricardo with Awaiting > > upstream status in patchwork (I thought that he has fixed just Apalis > > iMX6), but seems the patch was > > lost somewhere, as I can not find it nor in u-boot-imx/next neither > > in u-boot-imx/master branches. > > Thanks for providing the fix (at least for the Toradex boards) > > And I do guess that more i.MX6 boards are affected ... I think there's just one other. The imx8qm_rom7720_a1 references CONFIG_FSL_ESDHC still, but I don't see any other i.MX8 platforms doing anything with the symbol to compare with. -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20191206/9b1d842c/attachment.sig> ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion 2019-12-06 18:59 ` Tom Rini @ 2019-12-09 15:03 ` Oliver Graute 2019-12-09 15:07 ` Tom Rini 0 siblings, 1 reply; 7+ messages in thread From: Oliver Graute @ 2019-12-09 15:03 UTC (permalink / raw) To: u-boot On 06/12/19, Tom Rini wrote: > On Fri, Dec 06, 2019 at 06:23:09PM +0100, Lukasz Majewski wrote: > > Hi Igor, > > > > > Hi Stefano > > > > > > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk@gmail.com> > > > wrote: > > > > > > > > From: Igor Opaniuk <igor.opaniuk@toradex.com> > > > > > > > > Not all CONFIG_FSL_ESDHC defines were properly replaced with > > > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > > > > Colibri iMX6 SoMs. > > > > > > > > U-boot is stuck after this message: > > > > Commercial temperature grade DDR3 timings, 64bit bus width. > > > > Trying to boot from MMC1 > > > > > > > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > > > > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> > > > > --- > > > > > > > > board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- > > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c > > > > b/board/toradex/colibri_imx6/colibri_imx6.c index > > > > ad40b589c1..44173dde1f 100644 --- > > > > a/board/toradex/colibri_imx6/colibri_imx6.c +++ > > > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@ > > > > iomux_v3_cfg_t const uart1_pads[] = { > > > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; > > > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > > /* Colibri MMC */ > > > > iomux_v3_cfg_t const usdhc1_pads[] = { > > > > MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > > > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) > > > > } > > > > #endif > > > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > > /* use the following sequence: eMMC, MMC */ > > > > struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { > > > > {USDHC3_BASE_ADDR}, > > > > -- > > > > 2.17.1 > > > > > > > > > > I've just found the same fix [1] but from Ricardo with Awaiting > > > upstream status in patchwork (I thought that he has fixed just Apalis > > > iMX6), but seems the patch was > > > lost somewhere, as I can not find it nor in u-boot-imx/next neither > > > in u-boot-imx/master branches. > > > > Thanks for providing the fix (at least for the Toradex boards) > > > > And I do guess that more i.MX6 boards are affected ... > > I think there's just one other. The imx8qm_rom7720_a1 references > CONFIG_FSL_ESDHC still, but I don't see any other i.MX8 platforms doing > anything with the symbol to compare with. thx for that hint, so I must replace CONFIG_FSL_ESDHC with CONFIG_FSL_ESDHC_IMX in board/advantech/imx8qm_rom7720_a1/spl.c ? Best regards, Oliver ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion 2019-12-09 15:03 ` Oliver Graute @ 2019-12-09 15:07 ` Tom Rini 0 siblings, 0 replies; 7+ messages in thread From: Tom Rini @ 2019-12-09 15:07 UTC (permalink / raw) To: u-boot On Mon, Dec 09, 2019 at 03:03:48PM +0000, Oliver Graute wrote: > On 06/12/19, Tom Rini wrote: > > On Fri, Dec 06, 2019 at 06:23:09PM +0100, Lukasz Majewski wrote: > > > Hi Igor, > > > > > > > Hi Stefano > > > > > > > > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk@gmail.com> > > > > wrote: > > > > > > > > > > From: Igor Opaniuk <igor.opaniuk@toradex.com> > > > > > > > > > > Not all CONFIG_FSL_ESDHC defines were properly replaced with > > > > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > > > > > Colibri iMX6 SoMs. > > > > > > > > > > U-boot is stuck after this message: > > > > > Commercial temperature grade DDR3 timings, 64bit bus width. > > > > > Trying to boot from MMC1 > > > > > > > > > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > > > > > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> > > > > > --- > > > > > > > > > > board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- > > > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > > > > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c > > > > > b/board/toradex/colibri_imx6/colibri_imx6.c index > > > > > ad40b589c1..44173dde1f 100644 --- > > > > > a/board/toradex/colibri_imx6/colibri_imx6.c +++ > > > > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@ > > > > > iomux_v3_cfg_t const uart1_pads[] = { > > > > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; > > > > > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > > > /* Colibri MMC */ > > > > > iomux_v3_cfg_t const usdhc1_pads[] = { > > > > > MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > > > > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) > > > > > } > > > > > #endif > > > > > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > > > /* use the following sequence: eMMC, MMC */ > > > > > struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { > > > > > {USDHC3_BASE_ADDR}, > > > > > -- > > > > > 2.17.1 > > > > > > > > > > > > > I've just found the same fix [1] but from Ricardo with Awaiting > > > > upstream status in patchwork (I thought that he has fixed just Apalis > > > > iMX6), but seems the patch was > > > > lost somewhere, as I can not find it nor in u-boot-imx/next neither > > > > in u-boot-imx/master branches. > > > > > > Thanks for providing the fix (at least for the Toradex boards) > > > > > > And I do guess that more i.MX6 boards are affected ... > > > > I think there's just one other. The imx8qm_rom7720_a1 references > > CONFIG_FSL_ESDHC still, but I don't see any other i.MX8 platforms doing > > anything with the symbol to compare with. > > thx for that hint, so I must replace CONFIG_FSL_ESDHC with > CONFIG_FSL_ESDHC_IMX in board/advantech/imx8qm_rom7720_a1/spl.c ? Yes, and confirm that everything works as expected for the appropriate use cases. Thanks! -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20191209/1965ff24/attachment.sig> ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion 2019-12-06 16:24 [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion Igor Opaniuk 2019-12-06 16:39 ` Igor Opaniuk @ 2019-12-28 10:48 ` sbabic at denx.de 1 sibling, 0 replies; 7+ messages in thread From: sbabic at denx.de @ 2019-12-28 10:48 UTC (permalink / raw) To: u-boot > From: Igor Opaniuk <igor.opaniuk@toradex.com> > Not all CONFIG_FSL_ESDHC defines were properly replaced with > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > Colibri iMX6 SoMs. > U-boot is stuck after this message: > Commercial temperature grade DDR3 timings, 64bit bus width. > Trying to boot from MMC1 > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Applied to u-boot-imx, master, thanks ! Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de ===================================================================== ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-12-28 10:48 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-12-06 16:24 [RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion Igor Opaniuk 2019-12-06 16:39 ` Igor Opaniuk 2019-12-06 17:23 ` Lukasz Majewski 2019-12-06 18:59 ` Tom Rini 2019-12-09 15:03 ` Oliver Graute 2019-12-09 15:07 ` Tom Rini 2019-12-28 10:48 ` sbabic at denx.de
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.