From: Joel Stanley <joel@jms.id.au>
To: Quan Nguyen <quan@os.amperecomputing.com>
Cc: OpenBMC Maillist <openbmc@lists.ozlabs.org>,
"Thang Q . Nguyen" <thang@os.amperecomputing.com>,
Open Source Submission <patches@amperecomputing.com>,
Phong Vo <phong@os.amperecomputing.com>
Subject: Re: [PATCH 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Jade BMC
Date: Fri, 27 Nov 2020 03:35:26 +0000 [thread overview]
Message-ID: <CACPK8Xfp4hv4nWrBNDRS=fxSrpMOfSJPGM3Z8fYawZNPRYf-3Q@mail.gmail.com> (raw)
In-Reply-To: <20201127024158.1486-3-quan@os.amperecomputing.com>
On Fri, 27 Nov 2020 at 02:42, Quan Nguyen <quan@os.amperecomputing.com> wrote:
>
> The Mt. Jade BMC is an ASPEED AST2500-based BMC for the Mt. Jade
> hardware reference platform with Ampere's Altra Processor Family.
Hello Quan,
This patch looks good. Some minor comments below.
>
> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
> Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
> Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> .../arm/boot/dts/aspeed-bmc-ampere-mtjade.dts | 568 ++++++++++++++++++
> 2 files changed, 569 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9537b2e5aad6..6d4ae66f8cf7 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1394,6 +1394,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-ast2500-evb.dtb \
> aspeed-ast2600-evb.dtb \
> aspeed-bmc-amd-ethanolx.dtb \
> + aspeed-bmc-ampere-mtjade.dtb \
> aspeed-bmc-arm-centriq2400-rep.dtb \
> aspeed-bmc-arm-stardragon4800-rep2.dtb \
> aspeed-bmc-bytedance-g220a.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
> new file mode 100644
> index 000000000000..c89ab60bff74
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
> @@ -0,0 +1,568 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/dts-v1/;
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "Ampere Mt. Jade BMC";
> + compatible = "ampere,mtjade-bmc", "aspeed,ast2500";
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200 earlyprintk";
> + };
> +
> + memory@80000000 {
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + vga_memory: framebuffer@9f000000 {
> + no-map;
> + reg = <0x9f000000 0x01000000>; /* 16M */
> + };
> +
> + flash_memory: region@98000000 {
This is used by the aspeed-lpc-ctrl driver to map some of the BMC's
memory space into the LPC address space, allowing complicated host <->
bmc data exchange. Normally this is only used by the PowerPC
platforms.
> + no-map;
> + reg = <0x98000000 0x04000000>; /* 64M */
> + };
> +
> + gfx_memory: framebuffer {
Are you sure your system uses this? This is for the BMC's internal
graphic device, not the PCIe attached graphic device. It only does
something if you have added code to your BMC that displays something.
Most platforms only use the PCIe device.
> + size = <0x01000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> +
> + video_engine_memory: jpegbuffer {
> + size = <0x02000000>; /* 32M */
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + fault {
> + gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>;
> + };
> +
> + identify {
> + gpios = <&gpio ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + shutdown_ack {
> + label = "SHUTDOWN_ACK";
> + gpios = <&gpio ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(G, 2)>;
> + };
> +
> + reboot_ack {
> + label = "REBOOT_ACK";
> + gpios = <&gpio ASPEED_GPIO(J, 3) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(J, 3)>;
> + };
> +
> + S0_overtemp {
> + label = "S0_OVERTEMP";
> + gpios = <&gpio ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(G, 3)>;
> + };
> +
> + S0_hightemp {
> + label = "S0_HIGHTEMP";
> + gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(J, 0)>;
> + };
> +
> + S0_cpu_fault {
> + label = "S0_CPU_FAULT";
> + gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
> + linux,code = <ASPEED_GPIO(J, 1)>;
> + };
> +
> + S1_overtemp {
> + label = "S1_OVERTEMP";
> + gpios = <&gpio ASPEED_GPIO(Z, 6) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(Z, 6)>;
> + };
> +
> + S1_hightemp {
> + label = "S1_HIGHTEMP";
> + gpios = <&gpio ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(AB, 0)>;
> + };
> +
> + S1_cpu_fault {
> + label = "S1_CPU_FAULT";
> + gpios = <&gpio ASPEED_GPIO(Z, 1) GPIO_ACTIVE_HIGH>;
> + linux,code = <ASPEED_GPIO(Z, 1)>;
> + };
> +
> + id_button {
> + label = "ID_BUTTON";
> + gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
> + linux,code = <ASPEED_GPIO(Q, 5)>;
> + };
> +
> + };
> +
> + gpioA0mux: mux-controller {
> + compatible = "gpio-mux";
> + #mux-control-cells = <0>;
> + mux-gpios = <&gpio ASPEED_GPIO(A, 0) GPIO_ACTIVE_LOW>;
> + };
> +
> + adc0mux: adc0mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 0>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc1mux: adc1mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 1>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc2mux: adc2mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 2>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc3mux: adc3mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 3>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc4mux: adc4mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 4>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc5mux: adc5mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 5>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc6mux: adc6mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 6>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc7mux: adc7mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 7>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc8mux: adc8mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 8>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc9mux: adc9mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 9>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc10mux: adc10mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 10>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc11mux: adc11mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 11>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc12mux: adc12mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 12>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + adc13mux: adc13mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 13>;
> + #io-channel-cells = <1>;
> + io-channel-names = "parent";
> + mux-controls = <&gpioA0mux>;
> + channels = "s0", "s1";
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc0mux 0>, <&adc0mux 1>,
> + <&adc1mux 0>, <&adc1mux 1>,
> + <&adc2mux 0>, <&adc2mux 1>,
> + <&adc3mux 0>, <&adc3mux 1>,
> + <&adc4mux 0>, <&adc4mux 1>,
> + <&adc5mux 0>, <&adc5mux 1>,
> + <&adc6mux 0>, <&adc6mux 1>,
> + <&adc7mux 0>, <&adc7mux 1>,
> + <&adc8mux 0>, <&adc8mux 1>,
> + <&adc9mux 0>, <&adc9mux 1>,
> + <&adc10mux 0>, <&adc10mux 1>,
> + <&adc11mux 0>, <&adc11mux 1>,
> + <&adc12mux 0>, <&adc12mux 1>,
> + <&adc13mux 0>, <&adc13mux 1>;
> + };
> +
> + iio-hwmon-adc14 {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 14>;
> + };
> +
> + iio-hwmon-battery {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 15>;
> + };
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + /* spi-max-frequency = <50000000>; */
> +#include "openbmc-flash-layout.dtsi"
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "pnor";
> + /* spi-max-frequency = <100000000>; */
> + };
> +};
> +
> +&uart1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd1_default
> + &pinctrl_rxd1_default
> + &pinctrl_ncts1_default
> + &pinctrl_nrts1_default>;
> +};
> +
> +&uart2 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd2_default
> + &pinctrl_rxd2_default>;
> +};
> +
> +&uart3 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd3_default
> + &pinctrl_rxd3_default>;
> +};
> +
> +&uart4 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd4_default
> + &pinctrl_rxd4_default>;
> +};
> +
> +/* The BMC's uart */
> +&uart5 {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "disabled";
This is disabled by default, if you don't use it then omit this line.
> +};
> +
> +&mac1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> + eeprom@50 {
> + compatible = "microchip,24c64", "atmel,24c64";
> + reg = <0x50>;
> + pagesize = <32>;
> + };
> +
> + inlet_mem2: tmp175@28 {
> + compatible = "ti,tmp175";
> + reg = <0x28>;
> + };
> +
> + inlet_cpu: tmp175@29 {
> + compatible = "ti,tmp175";
> + reg = <0x29>;
> + };
> +
> + inlet_mem1: tmp175@2a {
> + compatible = "ti,tmp175";
> + reg = <0x2a>;
> + };
> +
> + outlet_cpu: tmp175@2b {
> + compatible = "ti,tmp175";
> + reg = <0x2b>;
> + };
> +
> + outlet1: tmp175@2c {
> + compatible = "ti,tmp175";
> + reg = <0x2c>;
> + };
> +
> + outlet2: tmp175@2d {
> + compatible = "ti,tmp175";
> + reg = <0x2d>;
> + };
> +};
> +
> +&i2c4 {
> + status = "okay";
> + rtc@51 {
> + compatible = "nxp,pcf85063a";
> + reg = <0x51>;
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> + psu@58 {
> + compatible = "pmbus";
> + reg = <0x58>;
> + };
> +
> + psu@59 {
> + compatible = "pmbus";
> + reg = <0x59>;
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> +};
> +
> +&i2c8 {
> + status = "okay";
> +};
> +
> +&i2c9 {
> + status = "okay";
> +};
> +
> +&gfx {
> + status = "okay";
> + memory-region = <&gfx_memory>;
> +};
> +
> +&pinctrl {
> + aspeed,external-nodes = <&gfx &lhc>;
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2_default &pinctrl_pwm3_default
> + &pinctrl_pwm4_default &pinctrl_pwm5_default
> + &pinctrl_pwm6_default &pinctrl_pwm7_default>;
> +
> + fan@0 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> + };
> +
> + fan@1 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> + };
> +
> + fan@2 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> + };
> +
> + fan@3 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> + };
> +
> + fan@4 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> + };
> +
> + fan@5 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> + };
> +
> + fan@6 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> + };
> +
> + fan@7 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> + };
> +
> + fan@8 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> + };
> +
> + fan@9 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> + };
> +
> + fan@10 {
> + reg = <0x07>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
> + };
> +
> + fan@11 {
> + reg = <0x07>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
> + };
> +
> +};
> +
> +&vhub {
> + status = "okay";
> +};
> +
> +&adc {
> + status = "okay";
> +};
> +
> +&video {
> + status = "okay";
> + memory-region = <&video_engine_memory>;
> +};
> +
> +&gpio {
> + gpio-line-names =
> + /*A0-A7*/ "","","","S0_BMC_SPECIAL_BOOT","","","","",
> + /*B0-B7*/ "BMC_SELECT_EEPROM","","","",
> + "POWER_BUTTON","","","",
> + /*C0-C7*/ "","","","","","","","",
> + /*D0-D7*/ "","","","","","","","",
> + /*E0-E7*/ "","","","","","","","",
> + /*F0-F7*/ "","","BMC_SYS_PSON_L","S0_DDR_SAVE","PGOOD",
> + "S1_DDR_SAVE","","",
> + /*G0-G7*/ "S0_FW_BOOT_OK","SHD_REQ_L","","S0_OVERTEMP_L","","",
> + "","",
> + /*H0-H7*/ "","","","","","","","",
> + /*I0-I7*/ "","","S1_BMC_SPECIAL_BOOT","","","","","",
> + /*J0-J7*/ "S0_HIGHTEMP_L","S0_FAULT_L","S0_SCP_AUTH_FAIL_L","",
> + "","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","BMC_SYSRESET_L","SPI_AUTH_FAIL_L","","","",
> + /*M0-M7*/ "","","","","","","","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","","","","","",
> + /*P0-P7*/ "","","","","","","","",
> + /*Q0-Q7*/ "","","","","","UID_BUTTON","","",
> + /*R0-R7*/ "","","BMC_EXT_HIGHTEMP_L","","","RESET_BUTTON","","",
> + /*S0-S7*/ "","","","","","","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","","","","","","","",
> + /*V0-V7*/ "","","","","","","","",
> + /*W0-W7*/ "","","","","","","","",
> + /*X0-X7*/ "","","","","","","","",
> + /*Y0-Y7*/ "","","","","","","","",
> + /*Z0-Z7*/ "S0_BMC_PLIMIT","S1_FAULT_L","S1_FW_BOOT_OK","","",
> + "S1_SCP_AUTH_FAIL_L","S1_OVERTEMP_L","",
> + /*AA0-AA7*/ "","","","","","","","",
> + /*AB0-AB7*/ "S1_HIGHTEMP_L","S1_BMC_PLIMIT","S0_BMC_DDR_ADDR",
> + "S1_BMC_DDR_ADR","","","","",
> + /*AC0-AC7*/ "SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L",
> + "BMC_OCP_PG";
> +};
> +
Remove the blank line from the end.
> --
> 2.28.0
>
next prev parent reply other threads:[~2020-11-27 3:37 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-27 2:41 [PATCH 0/2] ARM: dts: aspeed: Add Ampere Mt. Jade BMC device Quan Nguyen
2020-11-27 2:41 ` [PATCH 1/2] dt-bindings: vendor-prefixes: Add an entry for AmpereComputing.com Quan Nguyen
2020-11-27 3:26 ` Joel Stanley
2020-11-30 1:38 ` Quan Nguyen OS
2020-11-27 2:41 ` [PATCH 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Jade BMC Quan Nguyen
2020-11-27 3:35 ` Joel Stanley [this message]
2020-11-30 1:46 ` Quan Nguyen OS
2020-12-08 4:36 [PATCH 0/2] ARM: dts: aspeed: Add Ampere Mt. Jade BMC device Quan Nguyen
2020-12-08 4:37 ` [PATCH 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Jade BMC Quan Nguyen
2020-12-08 4:37 ` Quan Nguyen
2020-12-08 4:41 ` Joel Stanley
2020-12-08 4:41 ` Joel Stanley
2020-12-08 8:08 ` Krzysztof Kozlowski
2020-12-08 8:08 ` Krzysztof Kozlowski
2020-12-09 2:19 ` Joel Stanley
2020-12-09 2:19 ` Joel Stanley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CACPK8Xfp4hv4nWrBNDRS=fxSrpMOfSJPGM3Z8fYawZNPRYf-3Q@mail.gmail.com' \
--to=joel@jms.id.au \
--cc=openbmc@lists.ozlabs.org \
--cc=patches@amperecomputing.com \
--cc=phong@os.amperecomputing.com \
--cc=quan@os.amperecomputing.com \
--cc=thang@os.amperecomputing.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.