[PATCH v4 1/4] dt-bindings: vendor-prefixes: Add prefix for EBBG

[PATCH v4 1/4] dt-bindings: vendor-prefixes: Add prefix for EBBG

[Joel Selvaraj]

Add a prefix for EBBG. They manufacture displays which are used in some
Xiaomi phones, but I could not find much details about the company.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 80e80fa53f8a..effd1cb995cf 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -337,6 +337,8 @@ patternProperties:
     description: Embedded Artists AB
   "^ebang,.*":
     description: Zhejiang Ebang Communication Co., Ltd
+  "^ebbg,.*":
+    description: EBBG
   "^ebs-systart,.*":
     description: EBS-SYSTART GmbH
   "^ebv,.*":
-- 
2.36.1

[PATCH v4 1/4] dt-bindings: vendor-prefixes: Add prefix for EBBG

[Joel Selvaraj]

Add a prefix for EBBG. They manufacture displays which are used in some
Xiaomi phones, but I could not find much details about the company.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 80e80fa53f8a..effd1cb995cf 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -337,6 +337,8 @@ patternProperties:
     description: Embedded Artists AB
   "^ebang,.*":
     description: Zhejiang Ebang Communication Co., Ltd
+  "^ebbg,.*":
+    description: EBBG
   "^ebs-systart,.*":
     description: EBS-SYSTART GmbH
   "^ebv,.*":
-- 
2.36.1

[PATCH v4 2/4] dt-bindings: display: Add bindings for EBBG FT8719

Add bindings for the EBBG FT8719 6.18" 2246x1080 DSI video mode panel,
which can be found on some Xiaomi Poco F1 phones. The backlight is
managed through the QCOM WLED driver.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes in v2: (Krzysztof Kozlowski's Suggestions)
 - Specify maxItems for reg
 - Cleanup and simplify the panel properties
 - In example change "|+" to "|' and "dsi0" to "dsi"

 .../bindings/display/panel/ebbg,ft8719.yaml   | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml b/Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml
new file mode 100644
index 000000000000..80deedc01c7c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ebbg,ft8719.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: EBBG FT8719 MIPI-DSI LCD panel
+
+maintainers:
+  - Joel Selvaraj <jo@jsfamily.in>
+
+description: |
+  The FT8719 panel from EBBG is a FHD+ LCD display panel with a resolution
+  of 1080x2246. It is a video mode DSI panel. The backlight is managed
+  through the QCOM WLED driver.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: ebbg,ft8719
+
+  reg:
+    maxItems: 1
+    description: DSI virtual channel of the peripheral
+
+  vddio-supply:
+    description: power IC supply regulator
+
+  vddpos-supply:
+    description: positive boost supply regulator
+
+  vddneg-supply:
+    description: negative boost supply regulator
+
+required:
+  - compatible
+  - reg
+  - vddio-supply
+  - vddpos-supply
+  - vddneg-supply
+  - reset-gpios
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      panel@0 {
+        compatible = "ebbg,ft8719";
+        reg = <0>;
+
+        vddio-supply = <&vreg_l14a_1p88>;
+        vddpos-supply = <&lab>;
+        vddneg-supply = <&ibb>;
+
+        reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+        backlight = <&pmi8998_wled>;
+
+        port {
+          ebbg_ft8719_in_0: endpoint {
+            remote-endpoint = <&dsi0_out>;
+          };
+        };
+      };
+    };
-- 
2.36.1

[PATCH v4 2/4] dt-bindings: display: Add bindings for EBBG FT8719

[Joel Selvaraj]

Add bindings for the EBBG FT8719 6.18" 2246x1080 DSI video mode panel,
which can be found on some Xiaomi Poco F1 phones. The backlight is
managed through the QCOM WLED driver.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes in v2: (Krzysztof Kozlowski's Suggestions)
 - Specify maxItems for reg
 - Cleanup and simplify the panel properties
 - In example change "|+" to "|' and "dsi0" to "dsi"

 .../bindings/display/panel/ebbg,ft8719.yaml   | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml b/Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml
new file mode 100644
index 000000000000..80deedc01c7c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ebbg,ft8719.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: EBBG FT8719 MIPI-DSI LCD panel
+
+maintainers:
+  - Joel Selvaraj <jo@jsfamily.in>
+
+description: |
+  The FT8719 panel from EBBG is a FHD+ LCD display panel with a resolution
+  of 1080x2246. It is a video mode DSI panel. The backlight is managed
+  through the QCOM WLED driver.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: ebbg,ft8719
+
+  reg:
+    maxItems: 1
+    description: DSI virtual channel of the peripheral
+
+  vddio-supply:
+    description: power IC supply regulator
+
+  vddpos-supply:
+    description: positive boost supply regulator
+
+  vddneg-supply:
+    description: negative boost supply regulator
+
+required:
+  - compatible
+  - reg
+  - vddio-supply
+  - vddpos-supply
+  - vddneg-supply
+  - reset-gpios
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      panel@0 {
+        compatible = "ebbg,ft8719";
+        reg = <0>;
+
+        vddio-supply = <&vreg_l14a_1p88>;
+        vddpos-supply = <&lab>;
+        vddneg-supply = <&ibb>;
+
+        reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+        backlight = <&pmi8998_wled>;
+
+        port {
+          ebbg_ft8719_in_0: endpoint {
+            remote-endpoint = <&dsi0_out>;
+          };
+        };
+      };
+    };
-- 
2.36.1

[PATCH v4 3/4] drm/mipi-dsi: Introduce mipi_dsi_dcs_write_seq macro

[Joel Selvaraj]

A helper macro that can be used to simplify sending DCS commands.
It is useful in scenarios like panel initialization which can sometimes
involve sending lot of DCS commands.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
Changes in v4: (Linus Walleij's Suggestion)
 - Introduce mipi_dsi_dcs_write_seq macro in include/drm/drm_mipi_dsi.h

 include/drm/drm_mipi_dsi.h | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h
index 147e51b6d241..4a5996901689 100644
--- a/include/drm/drm_mipi_dsi.h
+++ b/include/drm/drm_mipi_dsi.h
@@ -293,6 +293,23 @@ int mipi_dsi_dcs_set_display_brightness(struct mipi_dsi_device *dsi,
 int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi,
 					u16 *brightness);
 
+/**
+ * mipi_dsi_dcs_write_seq - transmit a DCS command with payload
+ * @dsi: DSI peripheral device
+ * @cmd: Command
+ * @seq: buffer containing data to be transmitted
+ */
+#define mipi_dsi_dcs_write_seq(dsi, cmd, seq...) do {				\
+		static const u8 d[] = { cmd, seq };				\
+		struct device *dev = &dsi->dev;	\
+		int ret;						\
+		ret = mipi_dsi_dcs_write_buffer(dsi, d, ARRAY_SIZE(d));	\
+		if (ret < 0) {						\
+			dev_err_ratelimited(dev, "sending command %#02x failed: %d\n", cmd, ret); \
+			return ret;						\
+		}						\
+	} while (0)
+
 /**
  * struct mipi_dsi_driver - DSI driver
  * @driver: device driver model driver
-- 
2.36.1

[PATCH v4 3/4] drm/mipi-dsi: Introduce mipi_dsi_dcs_write_seq macro

[Joel Selvaraj]

A helper macro that can be used to simplify sending DCS commands.
It is useful in scenarios like panel initialization which can sometimes
involve sending lot of DCS commands.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
Changes in v4: (Linus Walleij's Suggestion)
 - Introduce mipi_dsi_dcs_write_seq macro in include/drm/drm_mipi_dsi.h

 include/drm/drm_mipi_dsi.h | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h
index 147e51b6d241..4a5996901689 100644
--- a/include/drm/drm_mipi_dsi.h
+++ b/include/drm/drm_mipi_dsi.h
@@ -293,6 +293,23 @@ int mipi_dsi_dcs_set_display_brightness(struct mipi_dsi_device *dsi,
 int mipi_dsi_dcs_get_display_brightness(struct mipi_dsi_device *dsi,
 					u16 *brightness);
 
+/**
+ * mipi_dsi_dcs_write_seq - transmit a DCS command with payload
+ * @dsi: DSI peripheral device
+ * @cmd: Command
+ * @seq: buffer containing data to be transmitted
+ */
+#define mipi_dsi_dcs_write_seq(dsi, cmd, seq...) do {				\
+		static const u8 d[] = { cmd, seq };				\
+		struct device *dev = &dsi->dev;	\
+		int ret;						\
+		ret = mipi_dsi_dcs_write_buffer(dsi, d, ARRAY_SIZE(d));	\
+		if (ret < 0) {						\
+			dev_err_ratelimited(dev, "sending command %#02x failed: %d\n", cmd, ret); \
+			return ret;						\
+		}						\
+	} while (0)
+
 /**
  * struct mipi_dsi_driver - DSI driver
  * @driver: device driver model driver
-- 
2.36.1

[PATCH v4 4/4] drm/panel: introduce ebbg,ft8719 panel

[Joel Selvaraj]

Add DRM panel driver for EBBG FT8719 6.18" 2246x1080 DSI video mode
panel, which can be found on some Xiaomi Poco F1 phones. The panel's
backlight is managed through QCOM WLED driver.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
---
Changes in v4: (Linus Walleij's Suggestion)
 - Remove the driver specific dsi_dcs_write_seq macro
 - Use the newly introduced mipi_dsi_dcs_write_seq macro instead

Changes in v3: (Mostly Linus Walleij's Suggestions)
 - Removed ctx->prepared state variable as it's handled by the core
 - Print error in dsi_dcs_write_seq macro if it fails to write
 - Removed magic power on sequences as panel works fine without them

 MAINTAINERS                               |   7 +
 drivers/gpu/drm/panel/Kconfig             |  11 +
 drivers/gpu/drm/panel/Makefile            |   1 +
 drivers/gpu/drm/panel/panel-ebbg-ft8719.c | 285 ++++++++++++++++++++++
 4 files changed, 304 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-ebbg-ft8719.c

diff --git a/MAINTAINERS b/MAINTAINERS
index cd0f68d4a34a..dfd2c53aea00 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6018,6 +6018,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
 F:	drivers/gpu/drm/bridge/chipone-icn6211.c
 
+DRM DRIVER FOR EBBG FT8719 PANEL
+M:	Joel Selvaraj <jo@jsfamily.in>
+S:	Maintained
+T:	git git://anongit.freedesktop.org/drm/drm-misc
+F:	Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml
+F:	drivers/gpu/drm/panel/panel-ebbg-ft8719.c
+
 DRM DRIVER FOR FARADAY TVE200 TV ENCODER
 M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 9989a316fe88..77176df2e2ec 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -114,6 +114,17 @@ config DRM_PANEL_EDP
 	  that it can be automatically turned off when the panel goes into a
 	  low power state.
 
+config DRM_PANEL_EBBG_FT8719
+	tristate "EBBG FT8719 panel driver"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y here if you want to enable support for the EBBG FT8719
+	  video mode panel. Mainly found on Xiaomi Poco F1 mobile phone.
+	  The panel has a resolution of 1080x2246. It provides a MIPI DSI
+	  interface to the host.
+
 config DRM_PANEL_ELIDA_KD35T133
 	tristate "Elida KD35T133 panel driver"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index d99fbbce49d1..47cc20c1a770 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_DRM_PANEL_DSI_CM) += panel-dsi-cm.o
 obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
 obj-$(CONFIG_DRM_PANEL_EDP) += panel-edp.o
+obj-$(CONFIG_DRM_PANEL_EBBG_FT8719) += panel-ebbg-ft8719.o
 obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
 obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
 obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
diff --git a/drivers/gpu/drm/panel/panel-ebbg-ft8719.c b/drivers/gpu/drm/panel/panel-ebbg-ft8719.c
new file mode 100644
index 000000000000..386f8321b930
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-ebbg-ft8719.c
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022 Joel Selvaraj <jo@jsfamily.in>
+ * Generated with linux-mdss-dsi-panel-driver-generator from vendor device tree:
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+static const char * const regulator_names[] = {
+	"vddio",
+	"vddpos",
+	"vddneg",
+};
+
+static const unsigned long regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000
+};
+
+struct ebbg_ft8719 {
+	struct drm_panel panel;
+	struct mipi_dsi_device *dsi;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+};
+
+static inline
+struct ebbg_ft8719 *to_ebbg_ft8719(struct drm_panel *panel)
+{
+	return container_of(panel, struct ebbg_ft8719, panel);
+}
+
+static void ebbg_ft8719_reset(struct ebbg_ft8719 *ctx)
+{
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	usleep_range(4000, 5000);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+	usleep_range(1000, 2000);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	usleep_range(15000, 16000);
+}
+
+static int ebbg_ft8719_on(struct ebbg_ft8719 *ctx)
+{
+	struct mipi_dsi_device *dsi = ctx->dsi;
+	struct device *dev = &dsi->dev;
+	int ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_brightness(dsi, 0x00ff);
+	if (ret < 0) {
+		dev_err(dev, "Failed to set display brightness: %d\n", ret);
+		return ret;
+	}
+
+	mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x24);
+	mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_POWER_SAVE, 0x00);
+
+	ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to exit sleep mode: %d\n", ret);
+		return ret;
+	}
+	msleep(90);
+
+	ret = mipi_dsi_dcs_set_display_on(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to set display on: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ebbg_ft8719_off(struct ebbg_ft8719 *ctx)
+{
+	struct mipi_dsi_device *dsi = ctx->dsi;
+	struct device *dev = &dsi->dev;
+	int ret;
+
+	dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_off(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to set display off: %d\n", ret);
+		return ret;
+	}
+	usleep_range(10000, 11000);
+
+	ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to enter sleep mode: %d\n", ret);
+		return ret;
+	}
+	msleep(90);
+
+	return 0;
+}
+
+static int ebbg_ft8719_prepare(struct drm_panel *panel)
+{
+	struct ebbg_ft8719 *ctx = to_ebbg_ft8719(panel);
+	struct device *dev = &ctx->dsi->dev;
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ebbg_ft8719_reset(ctx);
+
+	ret = ebbg_ft8719_on(ctx);
+	if (ret < 0) {
+		dev_err(dev, "Failed to initialize panel: %d\n", ret);
+		gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ebbg_ft8719_unprepare(struct drm_panel *panel)
+{
+	struct ebbg_ft8719 *ctx = to_ebbg_ft8719(panel);
+	struct device *dev = &ctx->dsi->dev;
+	int ret;
+
+	ret = ebbg_ft8719_off(ctx);
+	if (ret < 0)
+		dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
+
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret)
+		dev_err(panel->dev, "Failed to disable regulators: %d\n", ret);
+
+	return 0;
+}
+
+static const struct drm_display_mode ebbg_ft8719_mode = {
+	.clock = (1080 + 28 + 4 + 16) * (2246 + 120 + 4 + 12) * 60 / 1000,
+	.hdisplay = 1080,
+	.hsync_start = 1080 + 28,
+	.hsync_end = 1080 + 28 + 4,
+	.htotal = 1080 + 28 + 4 + 16,
+	.vdisplay = 2246,
+	.vsync_start = 2246 + 120,
+	.vsync_end = 2246 + 120 + 4,
+	.vtotal = 2246 + 120 + 4 + 12,
+	.width_mm = 68,
+	.height_mm = 141,
+};
+
+static int ebbg_ft8719_get_modes(struct drm_panel *panel,
+				     struct drm_connector *connector)
+{
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_duplicate(connector->dev, &ebbg_ft8719_mode);
+	if (!mode)
+		return -ENOMEM;
+
+	drm_mode_set_name(mode);
+
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	connector->display_info.width_mm = mode->width_mm;
+	connector->display_info.height_mm = mode->height_mm;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs ebbg_ft8719_panel_funcs = {
+	.prepare = ebbg_ft8719_prepare,
+	.unprepare = ebbg_ft8719_unprepare,
+	.get_modes = ebbg_ft8719_get_modes,
+};
+
+static int ebbg_ft8719_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct ebbg_ft8719 *ctx;
+	int i, ret;
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to get regulators\n");
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+						regulator_enable_loads[i]);
+		if (ret)
+			return dev_err_probe(dev, ret,
+						 "Failed to set regulator load\n");
+	}
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(ctx->reset_gpio))
+		return dev_err_probe(dev, PTR_ERR(ctx->reset_gpio),
+				     "Failed to get reset-gpios\n");
+
+	ctx->dsi = dsi;
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+			  MIPI_DSI_CLOCK_NON_CONTINUOUS;
+
+	drm_panel_init(&ctx->panel, dev, &ebbg_ft8719_panel_funcs,
+		       DRM_MODE_CONNECTOR_DSI);
+
+	ret = drm_panel_of_backlight(&ctx->panel);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get backlight\n");
+
+	drm_panel_add(&ctx->panel);
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to attach to DSI host: %d\n", ret);
+		drm_panel_remove(&ctx->panel);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ebbg_ft8719_remove(struct mipi_dsi_device *dsi)
+{
+	struct ebbg_ft8719 *ctx = mipi_dsi_get_drvdata(dsi);
+	int ret;
+
+	ret = mipi_dsi_detach(dsi);
+	if (ret < 0)
+		dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret);
+
+	drm_panel_remove(&ctx->panel);
+
+	return 0;
+}
+
+static const struct of_device_id ebbg_ft8719_of_match[] = {
+	{ .compatible = "ebbg,ft8719" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ebbg_ft8719_of_match);
+
+static struct mipi_dsi_driver ebbg_ft8719_driver = {
+	.probe = ebbg_ft8719_probe,
+	.remove = ebbg_ft8719_remove,
+	.driver = {
+		.name = "panel-ebbg-ft8719",
+		.of_match_table = ebbg_ft8719_of_match,
+	},
+};
+module_mipi_dsi_driver(ebbg_ft8719_driver);
+
+MODULE_AUTHOR("Joel Selvaraj <jo@jsfamily.in>");
+MODULE_DESCRIPTION("DRM driver for EBBG FT8719 video dsi panel");
+MODULE_LICENSE("GPL v2");
-- 
2.36.1

[PATCH v4 4/4] drm/panel: introduce ebbg,ft8719 panel

[Joel Selvaraj]

Add DRM panel driver for EBBG FT8719 6.18" 2246x1080 DSI video mode
panel, which can be found on some Xiaomi Poco F1 phones. The panel's
backlight is managed through QCOM WLED driver.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
---
Changes in v4: (Linus Walleij's Suggestion)
 - Remove the driver specific dsi_dcs_write_seq macro
 - Use the newly introduced mipi_dsi_dcs_write_seq macro instead

Changes in v3: (Mostly Linus Walleij's Suggestions)
 - Removed ctx->prepared state variable as it's handled by the core
 - Print error in dsi_dcs_write_seq macro if it fails to write
 - Removed magic power on sequences as panel works fine without them

 MAINTAINERS                               |   7 +
 drivers/gpu/drm/panel/Kconfig             |  11 +
 drivers/gpu/drm/panel/Makefile            |   1 +
 drivers/gpu/drm/panel/panel-ebbg-ft8719.c | 285 ++++++++++++++++++++++
 4 files changed, 304 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-ebbg-ft8719.c

diff --git a/MAINTAINERS b/MAINTAINERS
index cd0f68d4a34a..dfd2c53aea00 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6018,6 +6018,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml
 F:	drivers/gpu/drm/bridge/chipone-icn6211.c
 
+DRM DRIVER FOR EBBG FT8719 PANEL
+M:	Joel Selvaraj <jo@jsfamily.in>
+S:	Maintained
+T:	git git://anongit.freedesktop.org/drm/drm-misc
+F:	Documentation/devicetree/bindings/display/panel/ebbg,ft8719.yaml
+F:	drivers/gpu/drm/panel/panel-ebbg-ft8719.c
+
 DRM DRIVER FOR FARADAY TVE200 TV ENCODER
 M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 9989a316fe88..77176df2e2ec 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -114,6 +114,17 @@ config DRM_PANEL_EDP
 	  that it can be automatically turned off when the panel goes into a
 	  low power state.
 
+config DRM_PANEL_EBBG_FT8719
+	tristate "EBBG FT8719 panel driver"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y here if you want to enable support for the EBBG FT8719
+	  video mode panel. Mainly found on Xiaomi Poco F1 mobile phone.
+	  The panel has a resolution of 1080x2246. It provides a MIPI DSI
+	  interface to the host.
+
 config DRM_PANEL_ELIDA_KD35T133
 	tristate "Elida KD35T133 panel driver"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index d99fbbce49d1..47cc20c1a770 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_DRM_PANEL_DSI_CM) += panel-dsi-cm.o
 obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
 obj-$(CONFIG_DRM_PANEL_EDP) += panel-edp.o
+obj-$(CONFIG_DRM_PANEL_EBBG_FT8719) += panel-ebbg-ft8719.o
 obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
 obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
 obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
diff --git a/drivers/gpu/drm/panel/panel-ebbg-ft8719.c b/drivers/gpu/drm/panel/panel-ebbg-ft8719.c
new file mode 100644
index 000000000000..386f8321b930
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-ebbg-ft8719.c
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022 Joel Selvaraj <jo@jsfamily.in>
+ * Generated with linux-mdss-dsi-panel-driver-generator from vendor device tree:
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+static const char * const regulator_names[] = {
+	"vddio",
+	"vddpos",
+	"vddneg",
+};
+
+static const unsigned long regulator_enable_loads[] = {
+	62000,
+	100000,
+	100000
+};
+
+struct ebbg_ft8719 {
+	struct drm_panel panel;
+	struct mipi_dsi_device *dsi;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+
+	struct gpio_desc *reset_gpio;
+};
+
+static inline
+struct ebbg_ft8719 *to_ebbg_ft8719(struct drm_panel *panel)
+{
+	return container_of(panel, struct ebbg_ft8719, panel);
+}
+
+static void ebbg_ft8719_reset(struct ebbg_ft8719 *ctx)
+{
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	usleep_range(4000, 5000);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+	usleep_range(1000, 2000);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	usleep_range(15000, 16000);
+}
+
+static int ebbg_ft8719_on(struct ebbg_ft8719 *ctx)
+{
+	struct mipi_dsi_device *dsi = ctx->dsi;
+	struct device *dev = &dsi->dev;
+	int ret;
+
+	dsi->mode_flags |= MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_brightness(dsi, 0x00ff);
+	if (ret < 0) {
+		dev_err(dev, "Failed to set display brightness: %d\n", ret);
+		return ret;
+	}
+
+	mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x24);
+	mipi_dsi_dcs_write_seq(dsi, MIPI_DCS_WRITE_POWER_SAVE, 0x00);
+
+	ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to exit sleep mode: %d\n", ret);
+		return ret;
+	}
+	msleep(90);
+
+	ret = mipi_dsi_dcs_set_display_on(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to set display on: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ebbg_ft8719_off(struct ebbg_ft8719 *ctx)
+{
+	struct mipi_dsi_device *dsi = ctx->dsi;
+	struct device *dev = &dsi->dev;
+	int ret;
+
+	dsi->mode_flags &= ~MIPI_DSI_MODE_LPM;
+
+	ret = mipi_dsi_dcs_set_display_off(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to set display off: %d\n", ret);
+		return ret;
+	}
+	usleep_range(10000, 11000);
+
+	ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to enter sleep mode: %d\n", ret);
+		return ret;
+	}
+	msleep(90);
+
+	return 0;
+}
+
+static int ebbg_ft8719_prepare(struct drm_panel *panel)
+{
+	struct ebbg_ft8719 *ctx = to_ebbg_ft8719(panel);
+	struct device *dev = &ctx->dsi->dev;
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ebbg_ft8719_reset(ctx);
+
+	ret = ebbg_ft8719_on(ctx);
+	if (ret < 0) {
+		dev_err(dev, "Failed to initialize panel: %d\n", ret);
+		gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ebbg_ft8719_unprepare(struct drm_panel *panel)
+{
+	struct ebbg_ft8719 *ctx = to_ebbg_ft8719(panel);
+	struct device *dev = &ctx->dsi->dev;
+	int ret;
+
+	ret = ebbg_ft8719_off(ctx);
+	if (ret < 0)
+		dev_err(dev, "Failed to un-initialize panel: %d\n", ret);
+
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+	if (ret)
+		dev_err(panel->dev, "Failed to disable regulators: %d\n", ret);
+
+	return 0;
+}
+
+static const struct drm_display_mode ebbg_ft8719_mode = {
+	.clock = (1080 + 28 + 4 + 16) * (2246 + 120 + 4 + 12) * 60 / 1000,
+	.hdisplay = 1080,
+	.hsync_start = 1080 + 28,
+	.hsync_end = 1080 + 28 + 4,
+	.htotal = 1080 + 28 + 4 + 16,
+	.vdisplay = 2246,
+	.vsync_start = 2246 + 120,
+	.vsync_end = 2246 + 120 + 4,
+	.vtotal = 2246 + 120 + 4 + 12,
+	.width_mm = 68,
+	.height_mm = 141,
+};
+
+static int ebbg_ft8719_get_modes(struct drm_panel *panel,
+				     struct drm_connector *connector)
+{
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_duplicate(connector->dev, &ebbg_ft8719_mode);
+	if (!mode)
+		return -ENOMEM;
+
+	drm_mode_set_name(mode);
+
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	connector->display_info.width_mm = mode->width_mm;
+	connector->display_info.height_mm = mode->height_mm;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs ebbg_ft8719_panel_funcs = {
+	.prepare = ebbg_ft8719_prepare,
+	.unprepare = ebbg_ft8719_unprepare,
+	.get_modes = ebbg_ft8719_get_modes,
+};
+
+static int ebbg_ft8719_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct ebbg_ft8719 *ctx;
+	int i, ret;
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
+		ctx->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+				      ctx->supplies);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to get regulators\n");
+
+	for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
+		ret = regulator_set_load(ctx->supplies[i].consumer,
+						regulator_enable_loads[i]);
+		if (ret)
+			return dev_err_probe(dev, ret,
+						 "Failed to set regulator load\n");
+	}
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(ctx->reset_gpio))
+		return dev_err_probe(dev, PTR_ERR(ctx->reset_gpio),
+				     "Failed to get reset-gpios\n");
+
+	ctx->dsi = dsi;
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+			  MIPI_DSI_CLOCK_NON_CONTINUOUS;
+
+	drm_panel_init(&ctx->panel, dev, &ebbg_ft8719_panel_funcs,
+		       DRM_MODE_CONNECTOR_DSI);
+
+	ret = drm_panel_of_backlight(&ctx->panel);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get backlight\n");
+
+	drm_panel_add(&ctx->panel);
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		dev_err(dev, "Failed to attach to DSI host: %d\n", ret);
+		drm_panel_remove(&ctx->panel);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ebbg_ft8719_remove(struct mipi_dsi_device *dsi)
+{
+	struct ebbg_ft8719 *ctx = mipi_dsi_get_drvdata(dsi);
+	int ret;
+
+	ret = mipi_dsi_detach(dsi);
+	if (ret < 0)
+		dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret);
+
+	drm_panel_remove(&ctx->panel);
+
+	return 0;
+}
+
+static const struct of_device_id ebbg_ft8719_of_match[] = {
+	{ .compatible = "ebbg,ft8719" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ebbg_ft8719_of_match);
+
+static struct mipi_dsi_driver ebbg_ft8719_driver = {
+	.probe = ebbg_ft8719_probe,
+	.remove = ebbg_ft8719_remove,
+	.driver = {
+		.name = "panel-ebbg-ft8719",
+		.of_match_table = ebbg_ft8719_of_match,
+	},
+};
+module_mipi_dsi_driver(ebbg_ft8719_driver);
+
+MODULE_AUTHOR("Joel Selvaraj <jo@jsfamily.in>");
+MODULE_DESCRIPTION("DRM driver for EBBG FT8719 video dsi panel");
+MODULE_LICENSE("GPL v2");
-- 
2.36.1

Re: [PATCH v4 3/4] drm/mipi-dsi: Introduce mipi_dsi_dcs_write_seq macro

[Linus Walleij]

On Wed, Jun 1, 2022 at 10:24 AM Joel Selvaraj <jo@jsfamily.in> wrote:

> A helper macro that can be used to simplify sending DCS commands.
> It is useful in scenarios like panel initialization which can sometimes
> involve sending lot of DCS commands.
>
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

Re: [PATCH v4 3/4] drm/mipi-dsi: Introduce mipi_dsi_dcs_write_seq macro

[Linus Walleij]

On Wed, Jun 1, 2022 at 10:24 AM Joel Selvaraj <jo@jsfamily.in> wrote:

> A helper macro that can be used to simplify sending DCS commands.
> It is useful in scenarios like panel initialization which can sometimes
> involve sending lot of DCS commands.
>
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

Re: [PATCH v4 4/4] drm/panel: introduce ebbg,ft8719 panel

[Linus Walleij]

On Wed, Jun 1, 2022 at 10:24 AM Joel Selvaraj <jo@jsfamily.in> wrote:

> Add DRM panel driver for EBBG FT8719 6.18" 2246x1080 DSI video mode
> panel, which can be found on some Xiaomi Poco F1 phones. The panel's
> backlight is managed through QCOM WLED driver.
>
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Thanks for working out my suggestions!

Yours,
Linus Walleij

Re: [PATCH v4 4/4] drm/panel: introduce ebbg,ft8719 panel

[Linus Walleij]

On Wed, Jun 1, 2022 at 10:24 AM Joel Selvaraj <jo@jsfamily.in> wrote:

> Add DRM panel driver for EBBG FT8719 6.18" 2246x1080 DSI video mode
> panel, which can be found on some Xiaomi Poco F1 phones. The panel's
> backlight is managed through QCOM WLED driver.
>
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Thanks for working out my suggestions!

Yours,
Linus Walleij