* [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
This patch set adds a new drm driver for HiSilicon Kirin hi6220 SoC.
Current testing and support board is Hikey board which is one of Linaro
96boards. It is an arm64 open source board. For more information about
this board, please access https://www.96boards.org.
Hardware Detail
---------------
The display subsystem of Hi6220 SoC is shown as bellow:
+-----+ +----------+ +-----+ +-------------+
| | | | | | | |
| FB |------>| ADE |---->| DSI |---->| External |
| | | | | | | HDMI/panel |
+-----+ +----------+ +-----+ +-------------+
- ADE(Advanced Display Engine) is the display controller. It contains 7
channels, 3 overlay compositors and a LDI.
- A channel looks like: DMA-->clip-->scale-->ctrans(or called csc).
- Overlay compositor is response to compose planes which come from 7
channels and pass composed image to LDI.
- LDI is response to generate timings and RGB data stream.
- DSI converts the RGB data stream from ADE to DSI packets.
- External HDMI/panel module is connected with DSI bus. Now Hikey use a
ADI's ADV7533 external HDMI chip.
Change History
-------------
Changes in v8:
- Rebase to v4.6-rc3
Changes in v7:
- Add config.mutex protection when accessing mode_config.connector_list.
- Clean up match data getting of kirin_drm_drv.c.
- A few Regs define clean up and typo fixs for ADE crtc and DSI encoder
driver.
- Fix vblank irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
Changes in v6:
- Cleanup values part of reg and clocks relevant properties.
- Change "pclk_dsi" clock name to "pclk".
Changes in v5:
- Remove endpoint unit address of dsi output port.
- Use syscon to access ADE media NOC QoS registers instread of directly
writing registers.
- Use reset controller to reset ADE instead of directly writing registers.
Changes in v4:
- Describe more specific of clocks and ports of binding docs.
- Fix indentation of binding docs.
Changes in v3:
- Move and rename all the files to kirin sub-directory.
So that we could separate different seires SoCs' driver.
- Make ade as the drm master node.
- Replace drm_platform_init, load, unload implementation.
- Use assigned-clocks to set clock rate.
- Use ports to connect display relevant nodes.
- Rename hisi_drm_dsi.c to dw_drm_dsi.c
- Make encoder type as DRM_MODE_ENCODER_DSI.
- A few cleanup on regs and code.
Changes in v2:
- Remove abtraction layer of plane/crtc/encoder/connector.
- Refactor atomic implementation according to Daniel Vetter's guides:
http://blog.ffwll.ch/2014/11/atomic-modeset-support-for-kms-drivers.html
http://blog.ffwll.ch/2015/09/xdc-2015-atomic-modesetting-for-drivers.html
http://blog.ffwll.ch/2015/08/atomic-modesetting-design-overview.html
- Use bridge instead of slave encoder to connect external HDMI.
- Move dt binding docs to bindings/display/hisilicon directory.
Xinliang Liu (10):
drm/hisilicon: Add device tree binding for hi6220 display subsystem
drm/hisilicon: Add hisilicon kirin drm master driver
drm/hisilicon: Add crtc driver for ADE
drm/hisilicon: Add plane driver for ADE
drm/hisilicon: Add vblank driver for ADE
drm/hisilicon: Add cma fbdev and hotplug
drm/hisilicon: Add designware dsi encoder driver
drm/hisilicon: Add designware dsi host driver
drm/hisilicon: Add support for external bridge
MAINTAINERS: Add maintainer for hisilicon DRM driver
.../bindings/display/hisilicon/dw-dsi.txt | 72 ++
.../bindings/display/hisilicon/hisi-ade.txt | 64 ++
MAINTAINERS | 10 +
drivers/gpu/drm/Kconfig | 2 +
drivers/gpu/drm/Makefile | 1 +
drivers/gpu/drm/hisilicon/Kconfig | 5 +
drivers/gpu/drm/hisilicon/Makefile | 5 +
drivers/gpu/drm/hisilicon/kirin/Kconfig | 10 +
drivers/gpu/drm/hisilicon/kirin/Makefile | 5 +
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 857 ++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++
drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 +++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 1057 ++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 367 +++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 31 +
15 files changed, 2819 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
--
2.8.0
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
This patch set adds a new drm driver for HiSilicon Kirin hi6220 SoC.
Current testing and support board is Hikey board which is one of Linaro
96boards. It is an arm64 open source board. For more information about
this board, please access https://www.96boards.org.
Hardware Detail
---------------
The display subsystem of Hi6220 SoC is shown as bellow:
+-----+ +----------+ +-----+ +-------------+
| | | | | | | |
| FB |------>| ADE |---->| DSI |---->| External |
| | | | | | | HDMI/panel |
+-----+ +----------+ +-----+ +-------------+
- ADE(Advanced Display Engine) is the display controller. It contains 7
channels, 3 overlay compositors and a LDI.
- A channel looks like: DMA-->clip-->scale-->ctrans(or called csc).
- Overlay compositor is response to compose planes which come from 7
channels and pass composed image to LDI.
- LDI is response to generate timings and RGB data stream.
- DSI converts the RGB data stream from ADE to DSI packets.
- External HDMI/panel module is connected with DSI bus. Now Hikey use a
ADI's ADV7533 external HDMI chip.
Change History
-------------
Changes in v8:
- Rebase to v4.6-rc3
Changes in v7:
- Add config.mutex protection when accessing mode_config.connector_list.
- Clean up match data getting of kirin_drm_drv.c.
- A few Regs define clean up and typo fixs for ADE crtc and DSI encoder
driver.
- Fix vblank irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
Changes in v6:
- Cleanup values part of reg and clocks relevant properties.
- Change "pclk_dsi" clock name to "pclk".
Changes in v5:
- Remove endpoint unit address of dsi output port.
- Use syscon to access ADE media NOC QoS registers instread of directly
writing registers.
- Use reset controller to reset ADE instead of directly writing registers.
Changes in v4:
- Describe more specific of clocks and ports of binding docs.
- Fix indentation of binding docs.
Changes in v3:
- Move and rename all the files to kirin sub-directory.
So that we could separate different seires SoCs' driver.
- Make ade as the drm master node.
- Replace drm_platform_init, load, unload implementation.
- Use assigned-clocks to set clock rate.
- Use ports to connect display relevant nodes.
- Rename hisi_drm_dsi.c to dw_drm_dsi.c
- Make encoder type as DRM_MODE_ENCODER_DSI.
- A few cleanup on regs and code.
Changes in v2:
- Remove abtraction layer of plane/crtc/encoder/connector.
- Refactor atomic implementation according to Daniel Vetter's guides:
http://blog.ffwll.ch/2014/11/atomic-modeset-support-for-kms-drivers.html
http://blog.ffwll.ch/2015/09/xdc-2015-atomic-modesetting-for-drivers.html
http://blog.ffwll.ch/2015/08/atomic-modesetting-design-overview.html
- Use bridge instead of slave encoder to connect external HDMI.
- Move dt binding docs to bindings/display/hisilicon directory.
Xinliang Liu (10):
drm/hisilicon: Add device tree binding for hi6220 display subsystem
drm/hisilicon: Add hisilicon kirin drm master driver
drm/hisilicon: Add crtc driver for ADE
drm/hisilicon: Add plane driver for ADE
drm/hisilicon: Add vblank driver for ADE
drm/hisilicon: Add cma fbdev and hotplug
drm/hisilicon: Add designware dsi encoder driver
drm/hisilicon: Add designware dsi host driver
drm/hisilicon: Add support for external bridge
MAINTAINERS: Add maintainer for hisilicon DRM driver
.../bindings/display/hisilicon/dw-dsi.txt | 72 ++
.../bindings/display/hisilicon/hisi-ade.txt | 64 ++
MAINTAINERS | 10 +
drivers/gpu/drm/Kconfig | 2 +
drivers/gpu/drm/Makefile | 1 +
drivers/gpu/drm/hisilicon/Kconfig | 5 +
drivers/gpu/drm/hisilicon/Makefile | 5 +
drivers/gpu/drm/hisilicon/kirin/Kconfig | 10 +
drivers/gpu/drm/hisilicon/kirin/Makefile | 5 +
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 857 ++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++
drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 +++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 1057 ++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 367 +++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 31 +
15 files changed, 2819 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
--
2.8.0
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 01/10] drm/hisilicon: Add device tree binding for hi6220 display subsystem
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add ADE display controller binding doc.
Add DesignWare DSI Host Controller v1.20a binding doc.
v8: None.
v7: Acked by Rob Herring.
v6:
- Cleanup values part of reg and clocks properties.
- Change "pclk_dsi" clock name to "pclk".
v5:
- Remove endpoint unit address of dsi output port.
- Add "hisilicon,noc-syscon" property for ADE NOC QoS syscon.
- Add "resets" property for ADE reset.
v4:
- Describe more specific of clocks and ports.
- Fix indentation.
v3:
- Make ade as the drm master node.
- Use assigned-clocks to set clock rate.
- Use ports to connect display relavant nodes.
v2:
- Move dt binding docs to bindings/display/hisilicon directory.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/display/hisilicon/dw-dsi.txt | 72 ++++++++++++++++++++++
.../bindings/display/hisilicon/hisi-ade.txt | 64 +++++++++++++++++++
2 files changed, 136 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
new file mode 100644
index 000000000000..d270bfe4e4e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
@@ -0,0 +1,72 @@
+Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver
+
+A DSI Host Controller resides in the middle of display controller and external
+HDMI converter or panel.
+
+Required properties:
+- compatible: value should be "hisilicon,hi6220-dsi".
+- reg: physical base address and length of dsi controller's registers.
+- clocks: contains APB clock phandle + clock-specifier pair.
+- clock-names: should be "pclk".
+- ports: contains DSI controller input and output sub port.
+ The input port connects to ADE output port with the reg value "0".
+ The output port with the reg value "1", it could connect to panel or
+ any other bridge endpoints.
+ See Documentation/devicetree/bindings/graph.txt for more device graph info.
+
+A example of HiKey board hi6220 SoC and board specific DT entry:
+Example:
+
+SoC specific:
+ dsi: dsi@f4107800 {
+ compatible = "hisilicon,hi6220-dsi";
+ reg = <0x0 0xf4107800 0x0 0x100>;
+ clocks = <&media_ctrl HI6220_DSI_PCLK>;
+ clock-names = "pclk";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 0 for input port */
+ port@0 {
+ reg = <0>;
+ dsi_in: endpoint {
+ remote-endpoint = <&ade_out>;
+ };
+ };
+ };
+ };
+
+
+Board specific:
+ &dsi {
+ status = "ok";
+
+ ports {
+ /* 1 for output port */
+ port@1 {
+ reg = <1>;
+
+ dsi_out0: endpoint@0 {
+ remote-endpoint = <&adv7533_in>;
+ };
+ };
+ };
+ };
+
+ &i2c2 {
+ ...
+
+ adv7533: adv7533@39 {
+ ...
+
+ port {
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi_out0>;
+ };
+ };
+ };
+ };
+
diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
new file mode 100644
index 000000000000..38dc9d60eef8
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
@@ -0,0 +1,64 @@
+Device-Tree bindings for hisilicon ADE display controller driver
+
+ADE (Advanced Display Engine) is the display controller which grab image
+data from memory, do composition, do post image processing, generate RGB
+timing stream and transfer to DSI.
+
+Required properties:
+- compatible: value should be "hisilicon,hi6220-ade".
+- reg: physical base address and length of the ADE controller's registers.
+- hisilicon,noc-syscon: ADE NOC QoS syscon.
+- resets: The ADE reset controller node.
+- interrupt: the ldi vblank interrupt number used.
+- clocks: a list of phandle + clock-specifier pairs, one for each entry
+ in clock-names.
+- clock-names: should contain:
+ "clk_ade_core" for the ADE core clock.
+ "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with
+ jpeg codec.
+ "clk_ade_pix" for the ADE pixel clok.
+- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks'
+ phandle + clock-specifier pairs.
+- assigned-clock-rates: clock rates, one for each entry in assigned-clocks.
+ The rate of "clk_ade_core" could be "360000000" or "180000000";
+ The rate of "clk_codec_jpeg" could be or less than "1440000000".
+ These rate values could be configured according to performance and power
+ consumption.
+- port: the output port. This contains one endpoint subnode, with its
+ remote-endpoint set to the phandle of the connected DSI input endpoint.
+ See Documentation/devicetree/bindings/graph.txt for more device graph info.
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent.
+
+
+A example of HiKey board hi6220 SoC specific DT entry:
+Example:
+
+ ade: ade@f4100000 {
+ compatible = "hisilicon,hi6220-ade";
+ reg = <0x0 0xf4100000 0x0 0x7800>;
+ reg-names = "ade_base";
+ hisilicon,noc-syscon = <&medianoc_ade>;
+ resets = <&media_ctrl MEDIA_ADE>;
+ interrupts = <0 115 4>; /* ldi interrupt */
+
+ clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>,
+ <&media_ctrl HI6220_ADE_PIX_SRC>;
+ /*clock name*/
+ clock-names = "clk_ade_core",
+ "clk_codec_jpeg",
+ "clk_ade_pix";
+
+ assigned-clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>;
+ assigned-clock-rates = <360000000>, <288000000>;
+ dma-coherent;
+
+ port {
+ ade_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ };
+ };
+ };
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 01/10] drm/hisilicon: Add device tree binding for hi6220 display subsystem
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add ADE display controller binding doc.
Add DesignWare DSI Host Controller v1.20a binding doc.
v8: None.
v7: Acked by Rob Herring.
v6:
- Cleanup values part of reg and clocks properties.
- Change "pclk_dsi" clock name to "pclk".
v5:
- Remove endpoint unit address of dsi output port.
- Add "hisilicon,noc-syscon" property for ADE NOC QoS syscon.
- Add "resets" property for ADE reset.
v4:
- Describe more specific of clocks and ports.
- Fix indentation.
v3:
- Make ade as the drm master node.
- Use assigned-clocks to set clock rate.
- Use ports to connect display relavant nodes.
v2:
- Move dt binding docs to bindings/display/hisilicon directory.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/display/hisilicon/dw-dsi.txt | 72 ++++++++++++++++++++++
.../bindings/display/hisilicon/hisi-ade.txt | 64 +++++++++++++++++++
2 files changed, 136 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
new file mode 100644
index 000000000000..d270bfe4e4e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
@@ -0,0 +1,72 @@
+Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver
+
+A DSI Host Controller resides in the middle of display controller and external
+HDMI converter or panel.
+
+Required properties:
+- compatible: value should be "hisilicon,hi6220-dsi".
+- reg: physical base address and length of dsi controller's registers.
+- clocks: contains APB clock phandle + clock-specifier pair.
+- clock-names: should be "pclk".
+- ports: contains DSI controller input and output sub port.
+ The input port connects to ADE output port with the reg value "0".
+ The output port with the reg value "1", it could connect to panel or
+ any other bridge endpoints.
+ See Documentation/devicetree/bindings/graph.txt for more device graph info.
+
+A example of HiKey board hi6220 SoC and board specific DT entry:
+Example:
+
+SoC specific:
+ dsi: dsi at f4107800 {
+ compatible = "hisilicon,hi6220-dsi";
+ reg = <0x0 0xf4107800 0x0 0x100>;
+ clocks = <&media_ctrl HI6220_DSI_PCLK>;
+ clock-names = "pclk";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 0 for input port */
+ port at 0 {
+ reg = <0>;
+ dsi_in: endpoint {
+ remote-endpoint = <&ade_out>;
+ };
+ };
+ };
+ };
+
+
+Board specific:
+ &dsi {
+ status = "ok";
+
+ ports {
+ /* 1 for output port */
+ port at 1 {
+ reg = <1>;
+
+ dsi_out0: endpoint at 0 {
+ remote-endpoint = <&adv7533_in>;
+ };
+ };
+ };
+ };
+
+ &i2c2 {
+ ...
+
+ adv7533: adv7533 at 39 {
+ ...
+
+ port {
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi_out0>;
+ };
+ };
+ };
+ };
+
diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
new file mode 100644
index 000000000000..38dc9d60eef8
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
@@ -0,0 +1,64 @@
+Device-Tree bindings for hisilicon ADE display controller driver
+
+ADE (Advanced Display Engine) is the display controller which grab image
+data from memory, do composition, do post image processing, generate RGB
+timing stream and transfer to DSI.
+
+Required properties:
+- compatible: value should be "hisilicon,hi6220-ade".
+- reg: physical base address and length of the ADE controller's registers.
+- hisilicon,noc-syscon: ADE NOC QoS syscon.
+- resets: The ADE reset controller node.
+- interrupt: the ldi vblank interrupt number used.
+- clocks: a list of phandle + clock-specifier pairs, one for each entry
+ in clock-names.
+- clock-names: should contain:
+ "clk_ade_core" for the ADE core clock.
+ "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with
+ jpeg codec.
+ "clk_ade_pix" for the ADE pixel clok.
+- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks'
+ phandle + clock-specifier pairs.
+- assigned-clock-rates: clock rates, one for each entry in assigned-clocks.
+ The rate of "clk_ade_core" could be "360000000" or "180000000";
+ The rate of "clk_codec_jpeg" could be or less than "1440000000".
+ These rate values could be configured according to performance and power
+ consumption.
+- port: the output port. This contains one endpoint subnode, with its
+ remote-endpoint set to the phandle of the connected DSI input endpoint.
+ See Documentation/devicetree/bindings/graph.txt for more device graph info.
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent.
+
+
+A example of HiKey board hi6220 SoC specific DT entry:
+Example:
+
+ ade: ade at f4100000 {
+ compatible = "hisilicon,hi6220-ade";
+ reg = <0x0 0xf4100000 0x0 0x7800>;
+ reg-names = "ade_base";
+ hisilicon,noc-syscon = <&medianoc_ade>;
+ resets = <&media_ctrl MEDIA_ADE>;
+ interrupts = <0 115 4>; /* ldi interrupt */
+
+ clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>,
+ <&media_ctrl HI6220_ADE_PIX_SRC>;
+ /*clock name*/
+ clock-names = "clk_ade_core",
+ "clk_codec_jpeg",
+ "clk_ade_pix";
+
+ assigned-clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>;
+ assigned-clock-rates = <360000000>, <288000000>;
+ dma-coherent;
+
+ port {
+ ade_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ };
+ };
+ };
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA, daniel-/w4YWyX8dFk,
robh-DgEjT+Ai2ygdnm+yROfE0A, daniel-rLtY4a/8tF1rovVCs/uTlw,
architt-sgV2jX0FEOL9JmXXK+q4OQ, airlied-cv59FeDIM0c,
corbet-T1hC0tSOHrs, catalin.marinas-5wv7dgnIgG8,
will.deacon-5wv7dgnIgG8, emil.l.velikov-Re5JQEeQqe8AvxtiuMwx3w,
mark.rutland-5wv7dgnIgG8
Cc: linux-doc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linuxarm-hv44wF8Li93QT0dZR+AlfA,
andy.green-QSEj5FYQhm4dnm+yROfE0A,
haojian.zhuang-QSEj5FYQhm4dnm+yROfE0A,
liguozhu-C8/M+/jPZTeaMJb+Lgu22Q, xuwei5-C8/M+/jPZTeaMJb+Lgu22Q,
w.f-hv44wF8Li93QT0dZR+AlfA, puck.chen-C8/M+/jPZTeaMJb+Lgu22Q,
bintian.wang-hv44wF8Li93QT0dZR+AlfA,
benjamin.gaignard-QSEj5FYQhm4dnm+yROfE0A,
xuyiping-C8/M+/jPZTeaMJb+Lgu22Q,
kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q,
zourongrong-hv44wF8Li93QT0dZR+AlfA,
lijianhua-hv44wF8Li93QT0dZR+AlfA,
sumit.semwal-QSEj5FYQhm4dnm+yROfE0A,
guodong.xu-QSEj5FYQhm4dnm+yROfE0A, Xinliang Liu
Add kirin DRM master driver for hi6220 SoC which used in HiKey board.
Add dumb buffer feature.
Add prime dmabuf feature.
v8: None.
v7:
- Add config.mutex protection when accessing mode_config.connector_list.
- Clean up match data getting.
v6: None.
v5: None.
v4: None.
v3:
- Move and rename all the files to kirin sub-directory.
So that we could separate different seires SoCs' driver.
- Replace drm_platform_init, load, unload implementation.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
---
drivers/gpu/drm/Kconfig | 2 +
drivers/gpu/drm/Makefile | 1 +
drivers/gpu/drm/hisilicon/Kconfig | 5 +
drivers/gpu/drm/hisilicon/Makefile | 5 +
drivers/gpu/drm/hisilicon/kirin/Kconfig | 9 +
drivers/gpu/drm/hisilicon/kirin/Makefile | 3 +
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 309 ++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 20 ++
8 files changed, 354 insertions(+)
create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
index 84c587a1fa93..838f99acc2c0 100644
--- a/drivers/gpu/drm/Kconfig
+++ b/drivers/gpu/drm/Kconfig
@@ -289,3 +289,5 @@ source "drivers/gpu/drm/imx/Kconfig"
source "drivers/gpu/drm/vc4/Kconfig"
source "drivers/gpu/drm/etnaviv/Kconfig"
+
+source "drivers/gpu/drm/hisilicon/Kconfig"
diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
index 6eb94fc561dc..327d29638137 100644
--- a/drivers/gpu/drm/Makefile
+++ b/drivers/gpu/drm/Makefile
@@ -78,3 +78,4 @@ obj-y += panel/
obj-y += bridge/
obj-$(CONFIG_DRM_FSL_DCU) += fsl-dcu/
obj-$(CONFIG_DRM_ETNAVIV) += etnaviv/
+obj-y += hisilicon/
diff --git a/drivers/gpu/drm/hisilicon/Kconfig b/drivers/gpu/drm/hisilicon/Kconfig
new file mode 100644
index 000000000000..558c61b1b8e8
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/Kconfig
@@ -0,0 +1,5 @@
+#
+# hisilicon drm device configuration.
+# Please keep this list sorted alphabetically
+
+source "drivers/gpu/drm/hisilicon/kirin/Kconfig"
diff --git a/drivers/gpu/drm/hisilicon/Makefile b/drivers/gpu/drm/hisilicon/Makefile
new file mode 100644
index 000000000000..e3f6d493c996
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for hisilicon drm drivers.
+# Please keep this list sorted alphabetically
+
+obj-$(CONFIG_DRM_HISI_KIRIN) += kirin/
diff --git a/drivers/gpu/drm/hisilicon/kirin/Kconfig b/drivers/gpu/drm/hisilicon/kirin/Kconfig
new file mode 100644
index 000000000000..3ac4b8edeac1
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/Kconfig
@@ -0,0 +1,9 @@
+config DRM_HISI_KIRIN
+ tristate "DRM Support for Hisilicon Kirin series SoCs Platform"
+ depends on DRM
+ select DRM_KMS_HELPER
+ select DRM_GEM_CMA_HELPER
+ select DRM_KMS_CMA_HELPER
+ help
+ Choose this option if you have a hisilicon Kirin chipsets(hi6220).
+ If M is selected the module will be called kirin-drm.
diff --git a/drivers/gpu/drm/hisilicon/kirin/Makefile b/drivers/gpu/drm/hisilicon/kirin/Makefile
new file mode 100644
index 000000000000..cb346de47d48
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/Makefile
@@ -0,0 +1,3 @@
+kirin-drm-y := kirin_drm_drv.o
+
+obj-$(CONFIG_DRM_HISI_KIRIN) += kirin-drm.o
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
new file mode 100644
index 000000000000..976c9b1a3fd3
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -0,0 +1,309 @@
+/*
+ * Hisilicon Kirin SoCs drm master driver
+ *
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * Author:
+ * Xinliang Liu <z.liuxinliang-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
+ * Xinliang Liu <xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ * Xinwei Kong <kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/of_platform.h>
+#include <linux/component.h>
+#include <linux/of_graph.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "kirin_drm_drv.h"
+
+static struct kirin_dc_ops *dc_ops;
+
+static int kirin_drm_kms_cleanup(struct drm_device *dev)
+{
+ dc_ops->cleanup(dev);
+ drm_mode_config_cleanup(dev);
+
+ return 0;
+}
+
+static const struct drm_mode_config_funcs kirin_drm_mode_config_funcs = {
+ .fb_create = drm_fb_cma_create,
+ .atomic_check = drm_atomic_helper_check,
+ .atomic_commit = drm_atomic_helper_commit,
+};
+
+static void kirin_drm_mode_config_init(struct drm_device *dev)
+{
+ dev->mode_config.min_width = 0;
+ dev->mode_config.min_height = 0;
+
+ dev->mode_config.max_width = 2048;
+ dev->mode_config.max_height = 2048;
+
+ dev->mode_config.funcs = &kirin_drm_mode_config_funcs;
+}
+
+static int kirin_drm_kms_init(struct drm_device *dev)
+{
+ int ret;
+
+ dev_set_drvdata(dev->dev, dev);
+
+ /* dev->mode_config initialization */
+ drm_mode_config_init(dev);
+ kirin_drm_mode_config_init(dev);
+
+ /* display controller init */
+ ret = dc_ops->init(dev);
+ if (ret)
+ goto err_mode_config_cleanup;
+
+ /* bind and init sub drivers */
+ ret = component_bind_all(dev->dev, dev);
+ if (ret) {
+ DRM_ERROR("failed to bind all component.\n");
+ goto err_dc_cleanup;
+ }
+
+ /* reset all the states of crtc/plane/encoder/connector */
+ drm_mode_config_reset(dev);
+
+ return 0;
+
+err_dc_cleanup:
+ dc_ops->cleanup(dev);
+err_mode_config_cleanup:
+ drm_mode_config_cleanup(dev);
+
+ return ret;
+}
+
+static const struct file_operations kirin_drm_fops = {
+ .owner = THIS_MODULE,
+ .open = drm_open,
+ .release = drm_release,
+ .unlocked_ioctl = drm_ioctl,
+#ifdef CONFIG_COMPAT
+ .compat_ioctl = drm_compat_ioctl,
+#endif
+ .poll = drm_poll,
+ .read = drm_read,
+ .llseek = no_llseek,
+ .mmap = drm_gem_cma_mmap,
+};
+
+static int kirin_gem_cma_dumb_create(struct drm_file *file,
+ struct drm_device *dev,
+ struct drm_mode_create_dumb *args)
+{
+ return drm_gem_cma_dumb_create_internal(file, dev, args);
+}
+
+static struct drm_driver kirin_drm_driver = {
+ .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME |
+ DRIVER_ATOMIC,
+ .fops = &kirin_drm_fops,
+ .set_busid = drm_platform_set_busid,
+
+ .gem_free_object = drm_gem_cma_free_object,
+ .gem_vm_ops = &drm_gem_cma_vm_ops,
+ .dumb_create = kirin_gem_cma_dumb_create,
+ .dumb_map_offset = drm_gem_cma_dumb_map_offset,
+ .dumb_destroy = drm_gem_dumb_destroy,
+
+ .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
+ .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
+ .gem_prime_export = drm_gem_prime_export,
+ .gem_prime_import = drm_gem_prime_import,
+ .gem_prime_get_sg_table = drm_gem_cma_prime_get_sg_table,
+ .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
+ .gem_prime_vmap = drm_gem_cma_prime_vmap,
+ .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
+ .gem_prime_mmap = drm_gem_cma_prime_mmap,
+
+ .name = "kirin",
+ .desc = "Hisilicon Kirin SoCs' DRM Driver",
+ .date = "20150718",
+ .major = 1,
+ .minor = 0,
+};
+
+static int compare_of(struct device *dev, void *data)
+{
+ return dev->of_node == data;
+}
+
+static int kirin_drm_connectors_register(struct drm_device *dev)
+{
+ struct drm_connector *connector;
+ struct drm_connector *failed_connector;
+ int ret;
+
+ mutex_lock(&dev->mode_config.mutex);
+ drm_for_each_connector(connector, dev) {
+ ret = drm_connector_register(connector);
+ if (ret) {
+ failed_connector = connector;
+ goto err;
+ }
+ }
+ mutex_unlock(&dev->mode_config.mutex);
+
+ return 0;
+
+err:
+ drm_for_each_connector(connector, dev) {
+ if (failed_connector == connector)
+ break;
+ drm_connector_unregister(connector);
+ }
+ mutex_unlock(&dev->mode_config.mutex);
+
+ return ret;
+}
+
+static int kirin_drm_bind(struct device *dev)
+{
+ struct drm_driver *driver = &kirin_drm_driver;
+ struct drm_device *drm_dev;
+ int ret;
+
+ drm_dev = drm_dev_alloc(driver, dev);
+ if (!drm_dev)
+ return -ENOMEM;
+
+ drm_dev->platformdev = to_platform_device(dev);
+
+ ret = kirin_drm_kms_init(drm_dev);
+ if (ret)
+ goto err_drm_dev_unref;
+
+ ret = drm_dev_register(drm_dev, 0);
+ if (ret)
+ goto err_kms_cleanup;
+
+ /* connectors should be registered after drm device register */
+ ret = kirin_drm_connectors_register(drm_dev);
+ if (ret)
+ goto err_drm_dev_unregister;
+
+ DRM_INFO("Initialized %s %d.%d.%d %s on minor %d\n",
+ driver->name, driver->major, driver->minor, driver->patchlevel,
+ driver->date, drm_dev->primary->index);
+
+ return 0;
+
+err_drm_dev_unregister:
+ drm_dev_unregister(drm_dev);
+err_kms_cleanup:
+ kirin_drm_kms_cleanup(drm_dev);
+err_drm_dev_unref:
+ drm_dev_unref(drm_dev);
+
+ return ret;
+}
+
+static void kirin_drm_unbind(struct device *dev)
+{
+ drm_put_dev(dev_get_drvdata(dev));
+}
+
+static const struct component_master_ops kirin_drm_ops = {
+ .bind = kirin_drm_bind,
+ .unbind = kirin_drm_unbind,
+};
+
+static struct device_node *kirin_get_remote_node(struct device_node *np)
+{
+ struct device_node *endpoint, *remote;
+
+ /* get the first endpoint, in our case only one remote node
+ * is connected to display controller.
+ */
+ endpoint = of_graph_get_next_endpoint(np, NULL);
+ if (!endpoint) {
+ DRM_ERROR("no valid endpoint node\n");
+ return ERR_PTR(-ENODEV);
+ }
+ of_node_put(endpoint);
+
+ remote = of_graph_get_remote_port_parent(endpoint);
+ if (!remote) {
+ DRM_ERROR("no valid remote node\n");
+ return ERR_PTR(-ENODEV);
+ }
+ of_node_put(remote);
+
+ if (!of_device_is_available(remote)) {
+ DRM_ERROR("not available for remote node\n");
+ return ERR_PTR(-ENODEV);
+ }
+
+ return remote;
+}
+
+static int kirin_drm_platform_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct component_match *match = NULL;
+ struct device_node *remote;
+
+ dc_ops = (struct kirin_dc_ops *)of_device_get_match_data(dev);
+ if (!dc_ops) {
+ DRM_ERROR("failed to get dt id data\n");
+ return -EINVAL;
+ }
+
+ remote = kirin_get_remote_node(np);
+ if (IS_ERR(remote))
+ return PTR_ERR(remote);
+
+ component_match_add(dev, &match, compare_of, remote);
+
+ return component_master_add_with_match(dev, &kirin_drm_ops, match);
+
+ return 0;
+}
+
+static int kirin_drm_platform_remove(struct platform_device *pdev)
+{
+ component_master_del(&pdev->dev, &kirin_drm_ops);
+ dc_ops = NULL;
+ return 0;
+}
+
+static const struct of_device_id kirin_drm_dt_ids[] = {
+ { .compatible = "hisilicon,hi6220-ade",
+ .data = &ade_dc_ops,
+ },
+ { /* end node */ },
+};
+MODULE_DEVICE_TABLE(of, kirin_drm_dt_ids);
+
+static struct platform_driver kirin_drm_platform_driver = {
+ .probe = kirin_drm_platform_probe,
+ .remove = kirin_drm_platform_remove,
+ .driver = {
+ .name = "kirin-drm",
+ .of_match_table = kirin_drm_dt_ids,
+ },
+};
+
+module_platform_driver(kirin_drm_platform_driver);
+
+MODULE_AUTHOR("Xinliang Liu <xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
+MODULE_AUTHOR("Xinliang Liu <z.liuxinliang-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>");
+MODULE_AUTHOR("Xinwei Kong <kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>");
+MODULE_DESCRIPTION("hisilicon Kirin SoCs' DRM master driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
new file mode 100644
index 000000000000..75e9d82356d4
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __KIRIN_DRM_DRV_H__
+#define __KIRIN_DRM_DRV_H__
+
+/* display controller init/cleanup ops */
+struct kirin_dc_ops {
+ int (*init)(struct drm_device *dev);
+ void (*cleanup)(struct drm_device *dev);
+};
+
+#endif /* __KIRIN_DRM_DRV_H__ */
--
2.8.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add kirin DRM master driver for hi6220 SoC which used in HiKey board.
Add dumb buffer feature.
Add prime dmabuf feature.
v8: None.
v7:
- Add config.mutex protection when accessing mode_config.connector_list.
- Clean up match data getting.
v6: None.
v5: None.
v4: None.
v3:
- Move and rename all the files to kirin sub-directory.
So that we could separate different seires SoCs' driver.
- Replace drm_platform_init, load, unload implementation.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
drivers/gpu/drm/Kconfig | 2 +
drivers/gpu/drm/Makefile | 1 +
drivers/gpu/drm/hisilicon/Kconfig | 5 +
drivers/gpu/drm/hisilicon/Makefile | 5 +
drivers/gpu/drm/hisilicon/kirin/Kconfig | 9 +
drivers/gpu/drm/hisilicon/kirin/Makefile | 3 +
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 309 ++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 20 ++
8 files changed, 354 insertions(+)
create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
index 84c587a1fa93..838f99acc2c0 100644
--- a/drivers/gpu/drm/Kconfig
+++ b/drivers/gpu/drm/Kconfig
@@ -289,3 +289,5 @@ source "drivers/gpu/drm/imx/Kconfig"
source "drivers/gpu/drm/vc4/Kconfig"
source "drivers/gpu/drm/etnaviv/Kconfig"
+
+source "drivers/gpu/drm/hisilicon/Kconfig"
diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
index 6eb94fc561dc..327d29638137 100644
--- a/drivers/gpu/drm/Makefile
+++ b/drivers/gpu/drm/Makefile
@@ -78,3 +78,4 @@ obj-y += panel/
obj-y += bridge/
obj-$(CONFIG_DRM_FSL_DCU) += fsl-dcu/
obj-$(CONFIG_DRM_ETNAVIV) += etnaviv/
+obj-y += hisilicon/
diff --git a/drivers/gpu/drm/hisilicon/Kconfig b/drivers/gpu/drm/hisilicon/Kconfig
new file mode 100644
index 000000000000..558c61b1b8e8
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/Kconfig
@@ -0,0 +1,5 @@
+#
+# hisilicon drm device configuration.
+# Please keep this list sorted alphabetically
+
+source "drivers/gpu/drm/hisilicon/kirin/Kconfig"
diff --git a/drivers/gpu/drm/hisilicon/Makefile b/drivers/gpu/drm/hisilicon/Makefile
new file mode 100644
index 000000000000..e3f6d493c996
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for hisilicon drm drivers.
+# Please keep this list sorted alphabetically
+
+obj-$(CONFIG_DRM_HISI_KIRIN) += kirin/
diff --git a/drivers/gpu/drm/hisilicon/kirin/Kconfig b/drivers/gpu/drm/hisilicon/kirin/Kconfig
new file mode 100644
index 000000000000..3ac4b8edeac1
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/Kconfig
@@ -0,0 +1,9 @@
+config DRM_HISI_KIRIN
+ tristate "DRM Support for Hisilicon Kirin series SoCs Platform"
+ depends on DRM
+ select DRM_KMS_HELPER
+ select DRM_GEM_CMA_HELPER
+ select DRM_KMS_CMA_HELPER
+ help
+ Choose this option if you have a hisilicon Kirin chipsets(hi6220).
+ If M is selected the module will be called kirin-drm.
diff --git a/drivers/gpu/drm/hisilicon/kirin/Makefile b/drivers/gpu/drm/hisilicon/kirin/Makefile
new file mode 100644
index 000000000000..cb346de47d48
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/Makefile
@@ -0,0 +1,3 @@
+kirin-drm-y := kirin_drm_drv.o
+
+obj-$(CONFIG_DRM_HISI_KIRIN) += kirin-drm.o
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
new file mode 100644
index 000000000000..976c9b1a3fd3
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -0,0 +1,309 @@
+/*
+ * Hisilicon Kirin SoCs drm master driver
+ *
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * Author:
+ * Xinliang Liu <z.liuxinliang@hisilicon.com>
+ * Xinliang Liu <xinliang.liu@linaro.org>
+ * Xinwei Kong <kong.kongxinwei@hisilicon.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/of_platform.h>
+#include <linux/component.h>
+#include <linux/of_graph.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "kirin_drm_drv.h"
+
+static struct kirin_dc_ops *dc_ops;
+
+static int kirin_drm_kms_cleanup(struct drm_device *dev)
+{
+ dc_ops->cleanup(dev);
+ drm_mode_config_cleanup(dev);
+
+ return 0;
+}
+
+static const struct drm_mode_config_funcs kirin_drm_mode_config_funcs = {
+ .fb_create = drm_fb_cma_create,
+ .atomic_check = drm_atomic_helper_check,
+ .atomic_commit = drm_atomic_helper_commit,
+};
+
+static void kirin_drm_mode_config_init(struct drm_device *dev)
+{
+ dev->mode_config.min_width = 0;
+ dev->mode_config.min_height = 0;
+
+ dev->mode_config.max_width = 2048;
+ dev->mode_config.max_height = 2048;
+
+ dev->mode_config.funcs = &kirin_drm_mode_config_funcs;
+}
+
+static int kirin_drm_kms_init(struct drm_device *dev)
+{
+ int ret;
+
+ dev_set_drvdata(dev->dev, dev);
+
+ /* dev->mode_config initialization */
+ drm_mode_config_init(dev);
+ kirin_drm_mode_config_init(dev);
+
+ /* display controller init */
+ ret = dc_ops->init(dev);
+ if (ret)
+ goto err_mode_config_cleanup;
+
+ /* bind and init sub drivers */
+ ret = component_bind_all(dev->dev, dev);
+ if (ret) {
+ DRM_ERROR("failed to bind all component.\n");
+ goto err_dc_cleanup;
+ }
+
+ /* reset all the states of crtc/plane/encoder/connector */
+ drm_mode_config_reset(dev);
+
+ return 0;
+
+err_dc_cleanup:
+ dc_ops->cleanup(dev);
+err_mode_config_cleanup:
+ drm_mode_config_cleanup(dev);
+
+ return ret;
+}
+
+static const struct file_operations kirin_drm_fops = {
+ .owner = THIS_MODULE,
+ .open = drm_open,
+ .release = drm_release,
+ .unlocked_ioctl = drm_ioctl,
+#ifdef CONFIG_COMPAT
+ .compat_ioctl = drm_compat_ioctl,
+#endif
+ .poll = drm_poll,
+ .read = drm_read,
+ .llseek = no_llseek,
+ .mmap = drm_gem_cma_mmap,
+};
+
+static int kirin_gem_cma_dumb_create(struct drm_file *file,
+ struct drm_device *dev,
+ struct drm_mode_create_dumb *args)
+{
+ return drm_gem_cma_dumb_create_internal(file, dev, args);
+}
+
+static struct drm_driver kirin_drm_driver = {
+ .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME |
+ DRIVER_ATOMIC,
+ .fops = &kirin_drm_fops,
+ .set_busid = drm_platform_set_busid,
+
+ .gem_free_object = drm_gem_cma_free_object,
+ .gem_vm_ops = &drm_gem_cma_vm_ops,
+ .dumb_create = kirin_gem_cma_dumb_create,
+ .dumb_map_offset = drm_gem_cma_dumb_map_offset,
+ .dumb_destroy = drm_gem_dumb_destroy,
+
+ .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
+ .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
+ .gem_prime_export = drm_gem_prime_export,
+ .gem_prime_import = drm_gem_prime_import,
+ .gem_prime_get_sg_table = drm_gem_cma_prime_get_sg_table,
+ .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
+ .gem_prime_vmap = drm_gem_cma_prime_vmap,
+ .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
+ .gem_prime_mmap = drm_gem_cma_prime_mmap,
+
+ .name = "kirin",
+ .desc = "Hisilicon Kirin SoCs' DRM Driver",
+ .date = "20150718",
+ .major = 1,
+ .minor = 0,
+};
+
+static int compare_of(struct device *dev, void *data)
+{
+ return dev->of_node == data;
+}
+
+static int kirin_drm_connectors_register(struct drm_device *dev)
+{
+ struct drm_connector *connector;
+ struct drm_connector *failed_connector;
+ int ret;
+
+ mutex_lock(&dev->mode_config.mutex);
+ drm_for_each_connector(connector, dev) {
+ ret = drm_connector_register(connector);
+ if (ret) {
+ failed_connector = connector;
+ goto err;
+ }
+ }
+ mutex_unlock(&dev->mode_config.mutex);
+
+ return 0;
+
+err:
+ drm_for_each_connector(connector, dev) {
+ if (failed_connector == connector)
+ break;
+ drm_connector_unregister(connector);
+ }
+ mutex_unlock(&dev->mode_config.mutex);
+
+ return ret;
+}
+
+static int kirin_drm_bind(struct device *dev)
+{
+ struct drm_driver *driver = &kirin_drm_driver;
+ struct drm_device *drm_dev;
+ int ret;
+
+ drm_dev = drm_dev_alloc(driver, dev);
+ if (!drm_dev)
+ return -ENOMEM;
+
+ drm_dev->platformdev = to_platform_device(dev);
+
+ ret = kirin_drm_kms_init(drm_dev);
+ if (ret)
+ goto err_drm_dev_unref;
+
+ ret = drm_dev_register(drm_dev, 0);
+ if (ret)
+ goto err_kms_cleanup;
+
+ /* connectors should be registered after drm device register */
+ ret = kirin_drm_connectors_register(drm_dev);
+ if (ret)
+ goto err_drm_dev_unregister;
+
+ DRM_INFO("Initialized %s %d.%d.%d %s on minor %d\n",
+ driver->name, driver->major, driver->minor, driver->patchlevel,
+ driver->date, drm_dev->primary->index);
+
+ return 0;
+
+err_drm_dev_unregister:
+ drm_dev_unregister(drm_dev);
+err_kms_cleanup:
+ kirin_drm_kms_cleanup(drm_dev);
+err_drm_dev_unref:
+ drm_dev_unref(drm_dev);
+
+ return ret;
+}
+
+static void kirin_drm_unbind(struct device *dev)
+{
+ drm_put_dev(dev_get_drvdata(dev));
+}
+
+static const struct component_master_ops kirin_drm_ops = {
+ .bind = kirin_drm_bind,
+ .unbind = kirin_drm_unbind,
+};
+
+static struct device_node *kirin_get_remote_node(struct device_node *np)
+{
+ struct device_node *endpoint, *remote;
+
+ /* get the first endpoint, in our case only one remote node
+ * is connected to display controller.
+ */
+ endpoint = of_graph_get_next_endpoint(np, NULL);
+ if (!endpoint) {
+ DRM_ERROR("no valid endpoint node\n");
+ return ERR_PTR(-ENODEV);
+ }
+ of_node_put(endpoint);
+
+ remote = of_graph_get_remote_port_parent(endpoint);
+ if (!remote) {
+ DRM_ERROR("no valid remote node\n");
+ return ERR_PTR(-ENODEV);
+ }
+ of_node_put(remote);
+
+ if (!of_device_is_available(remote)) {
+ DRM_ERROR("not available for remote node\n");
+ return ERR_PTR(-ENODEV);
+ }
+
+ return remote;
+}
+
+static int kirin_drm_platform_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct component_match *match = NULL;
+ struct device_node *remote;
+
+ dc_ops = (struct kirin_dc_ops *)of_device_get_match_data(dev);
+ if (!dc_ops) {
+ DRM_ERROR("failed to get dt id data\n");
+ return -EINVAL;
+ }
+
+ remote = kirin_get_remote_node(np);
+ if (IS_ERR(remote))
+ return PTR_ERR(remote);
+
+ component_match_add(dev, &match, compare_of, remote);
+
+ return component_master_add_with_match(dev, &kirin_drm_ops, match);
+
+ return 0;
+}
+
+static int kirin_drm_platform_remove(struct platform_device *pdev)
+{
+ component_master_del(&pdev->dev, &kirin_drm_ops);
+ dc_ops = NULL;
+ return 0;
+}
+
+static const struct of_device_id kirin_drm_dt_ids[] = {
+ { .compatible = "hisilicon,hi6220-ade",
+ .data = &ade_dc_ops,
+ },
+ { /* end node */ },
+};
+MODULE_DEVICE_TABLE(of, kirin_drm_dt_ids);
+
+static struct platform_driver kirin_drm_platform_driver = {
+ .probe = kirin_drm_platform_probe,
+ .remove = kirin_drm_platform_remove,
+ .driver = {
+ .name = "kirin-drm",
+ .of_match_table = kirin_drm_dt_ids,
+ },
+};
+
+module_platform_driver(kirin_drm_platform_driver);
+
+MODULE_AUTHOR("Xinliang Liu <xinliang.liu@linaro.org>");
+MODULE_AUTHOR("Xinliang Liu <z.liuxinliang@hisilicon.com>");
+MODULE_AUTHOR("Xinwei Kong <kong.kongxinwei@hisilicon.com>");
+MODULE_DESCRIPTION("hisilicon Kirin SoCs' DRM master driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
new file mode 100644
index 000000000000..75e9d82356d4
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __KIRIN_DRM_DRV_H__
+#define __KIRIN_DRM_DRV_H__
+
+/* display controller init/cleanup ops */
+struct kirin_dc_ops {
+ int (*init)(struct drm_device *dev);
+ void (*cleanup)(struct drm_device *dev);
+};
+
+#endif /* __KIRIN_DRM_DRV_H__ */
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 03/10] drm/hisilicon: Add crtc driver for ADE
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA, daniel-/w4YWyX8dFk,
robh-DgEjT+Ai2ygdnm+yROfE0A, daniel-rLtY4a/8tF1rovVCs/uTlw,
architt-sgV2jX0FEOL9JmXXK+q4OQ, airlied-cv59FeDIM0c,
corbet-T1hC0tSOHrs, catalin.marinas-5wv7dgnIgG8,
will.deacon-5wv7dgnIgG8, emil.l.velikov-Re5JQEeQqe8AvxtiuMwx3w,
mark.rutland-5wv7dgnIgG8
Cc: linux-doc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linuxarm-hv44wF8Li93QT0dZR+AlfA,
andy.green-QSEj5FYQhm4dnm+yROfE0A,
haojian.zhuang-QSEj5FYQhm4dnm+yROfE0A,
liguozhu-C8/M+/jPZTeaMJb+Lgu22Q, xuwei5-C8/M+/jPZTeaMJb+Lgu22Q,
w.f-hv44wF8Li93QT0dZR+AlfA, puck.chen-C8/M+/jPZTeaMJb+Lgu22Q,
bintian.wang-hv44wF8Li93QT0dZR+AlfA,
benjamin.gaignard-QSEj5FYQhm4dnm+yROfE0A,
xuyiping-C8/M+/jPZTeaMJb+Lgu22Q,
kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q,
zourongrong-hv44wF8Li93QT0dZR+AlfA,
lijianhua-hv44wF8Li93QT0dZR+AlfA,
sumit.semwal-QSEj5FYQhm4dnm+yROfE0A,
guodong.xu-QSEj5FYQhm4dnm+yROfE0A, Xinliang Liu
Add crtc funcs and helper funcs for ADE.
v8: None.
v7:
- A few Regs define clean up and typo fixs.
v6:
- Cleanup reg-names dt parsing.
v5:
- Use syscon to access ADE media NOC QoS registers instread of directly
writing registers.
- Use reset controller to reset ADE instead of directly writing registers.
v4: None.
v3:
- Make ade as the master driver.
- Use port to connect with encoder.
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
Reviewed-by: Archit Taneja <architt-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/gpu/drm/hisilicon/kirin/Makefile | 3 +-
drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 ++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 462 ++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 12 +
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 8 +
5 files changed, 714 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
diff --git a/drivers/gpu/drm/hisilicon/kirin/Makefile b/drivers/gpu/drm/hisilicon/kirin/Makefile
index cb346de47d48..2a61ab006ddb 100644
--- a/drivers/gpu/drm/hisilicon/kirin/Makefile
+++ b/drivers/gpu/drm/hisilicon/kirin/Makefile
@@ -1,3 +1,4 @@
-kirin-drm-y := kirin_drm_drv.o
+kirin-drm-y := kirin_drm_drv.o \
+ kirin_drm_ade.o
obj-$(CONFIG_DRM_HISI_KIRIN) += kirin-drm.o
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h b/drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
new file mode 100644
index 000000000000..4cf281b7ed63
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
@@ -0,0 +1,230 @@
+/*
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __KIRIN_ADE_REG_H__
+#define __KIRIN_ADE_REG_H__
+
+/*
+ * ADE Registers
+ */
+#define MASK(x) (BIT(x) - 1)
+
+#define ADE_CTRL 0x0004
+#define FRM_END_START_OFST 0
+#define FRM_END_START_MASK MASK(2)
+#define AUTO_CLK_GATE_EN_OFST 0
+#define AUTO_CLK_GATE_EN BIT(0)
+#define ADE_DISP_SRC_CFG 0x0018
+#define ADE_CTRL1 0x008C
+#define ADE_EN 0x0100
+#define ADE_DISABLE 0
+#define ADE_ENABLE 1
+/* reset and reload regs */
+#define ADE_SOFT_RST_SEL(x) (0x0078 + (x) * 0x4)
+#define ADE_RELOAD_DIS(x) (0x00AC + (x) * 0x4)
+#define RDMA_OFST 0
+#define CLIP_OFST 15
+#define SCL_OFST 21
+#define CTRAN_OFST 24
+#define OVLY_OFST 37 /* 32+5 */
+/* channel regs */
+#define RD_CH_CTRL(x) (0x1004 + (x) * 0x80)
+#define RD_CH_ADDR(x) (0x1008 + (x) * 0x80)
+#define RD_CH_SIZE(x) (0x100C + (x) * 0x80)
+#define RD_CH_STRIDE(x) (0x1010 + (x) * 0x80)
+#define RD_CH_SPACE(x) (0x1014 + (x) * 0x80)
+#define RD_CH_EN(x) (0x1020 + (x) * 0x80)
+/* overlay regs */
+#define ADE_OVLY1_TRANS_CFG 0x002C
+#define ADE_OVLY_CTL 0x0098
+#define ADE_OVLY_CH_XY0(x) (0x2004 + (x) * 4)
+#define ADE_OVLY_CH_XY1(x) (0x2024 + (x) * 4)
+#define ADE_OVLY_CH_CTL(x) (0x204C + (x) * 4)
+#define ADE_OVLY_OUTPUT_SIZE(x) (0x2070 + (x) * 8)
+#define OUTPUT_XSIZE_OFST 16
+#define ADE_OVLYX_CTL(x) (0x209C + (x) * 4)
+#define CH_OVLY_SEL_OFST(x) ((x) * 4)
+#define CH_OVLY_SEL_MASK MASK(2)
+#define CH_OVLY_SEL_VAL(x) ((x) + 1)
+#define CH_ALP_MODE_OFST 0
+#define CH_ALP_SEL_OFST 2
+#define CH_UNDER_ALP_SEL_OFST 4
+#define CH_EN_OFST 6
+#define CH_ALP_GBL_OFST 15
+#define CH_SEL_OFST 28
+/* ctran regs */
+#define ADE_CTRAN_DIS(x) (0x5004 + (x) * 0x100)
+#define CTRAN_BYPASS_ON 1
+#define CTRAN_BYPASS_OFF 0
+#define ADE_CTRAN_IMAGE_SIZE(x) (0x503C + (x) * 0x100)
+/* clip regs */
+#define ADE_CLIP_DISABLE(x) (0x6800 + (x) * 0x100)
+#define ADE_CLIP_SIZE0(x) (0x6804 + (x) * 0x100)
+#define ADE_CLIP_SIZE1(x) (0x6808 + (x) * 0x100)
+
+/*
+ * LDI Registers
+ */
+#define LDI_HRZ_CTRL0 0x7400
+#define HBP_OFST 20
+#define LDI_HRZ_CTRL1 0x7404
+#define LDI_VRT_CTRL0 0x7408
+#define VBP_OFST 20
+#define LDI_VRT_CTRL1 0x740C
+#define LDI_PLR_CTRL 0x7410
+#define FLAG_NVSYNC BIT(0)
+#define FLAG_NHSYNC BIT(1)
+#define FLAG_NPIXCLK BIT(2)
+#define FLAG_NDE BIT(3)
+#define LDI_DSP_SIZE 0x7414
+#define VSIZE_OFST 20
+#define LDI_INT_EN 0x741C
+#define FRAME_END_INT_EN_OFST 1
+#define LDI_CTRL 0x7420
+#define BPP_OFST 3
+#define DATA_GATE_EN BIT(2)
+#define LDI_EN BIT(0)
+#define LDI_MSK_INT 0x7428
+#define LDI_INT_CLR 0x742C
+#define LDI_WORK_MODE 0x7430
+#define LDI_HDMI_DSI_GT 0x7434
+
+/*
+ * ADE media bus service regs
+ */
+#define ADE0_QOSGENERATOR_MODE 0x010C
+#define QOSGENERATOR_MODE_MASK MASK(2)
+#define ADE0_QOSGENERATOR_EXTCONTROL 0x0118
+#define SOCKET_QOS_EN BIT(0)
+#define ADE1_QOSGENERATOR_MODE 0x020C
+#define ADE1_QOSGENERATOR_EXTCONTROL 0x0218
+
+/*
+ * ADE regs relevant enums
+ */
+enum frame_end_start {
+ /* regs take effect in every vsync */
+ REG_EFFECTIVE_IN_VSYNC = 0,
+ /* regs take effect in fist ade en and every frame end */
+ REG_EFFECTIVE_IN_ADEEN_FRMEND,
+ /* regs take effect in ade en immediately */
+ REG_EFFECTIVE_IN_ADEEN,
+ /* regs take effect in first vsync and every frame end */
+ REG_EFFECTIVE_IN_VSYNC_FRMEND
+};
+
+enum ade_fb_format {
+ ADE_RGB_565 = 0,
+ ADE_BGR_565,
+ ADE_XRGB_8888,
+ ADE_XBGR_8888,
+ ADE_ARGB_8888,
+ ADE_ABGR_8888,
+ ADE_RGBA_8888,
+ ADE_BGRA_8888,
+ ADE_RGB_888,
+ ADE_BGR_888 = 9,
+ ADE_FORMAT_UNSUPPORT = 800
+};
+
+enum ade_channel {
+ ADE_CH1 = 0, /* channel 1 for primary plane */
+ ADE_CH_NUM
+};
+
+enum ade_scale {
+ ADE_SCL1 = 0,
+ ADE_SCL2,
+ ADE_SCL3,
+ ADE_SCL_NUM
+};
+
+enum ade_ctran {
+ ADE_CTRAN1 = 0,
+ ADE_CTRAN2,
+ ADE_CTRAN3,
+ ADE_CTRAN4,
+ ADE_CTRAN5,
+ ADE_CTRAN6,
+ ADE_CTRAN_NUM
+};
+
+enum ade_overlay {
+ ADE_OVLY1 = 0,
+ ADE_OVLY2,
+ ADE_OVLY3,
+ ADE_OVLY_NUM
+};
+
+enum ade_alpha_mode {
+ ADE_ALP_GLOBAL = 0,
+ ADE_ALP_PIXEL,
+ ADE_ALP_PIXEL_AND_GLB
+};
+
+enum ade_alpha_blending_mode {
+ ADE_ALP_MUL_COEFF_0 = 0, /* alpha */
+ ADE_ALP_MUL_COEFF_1, /* 1-alpha */
+ ADE_ALP_MUL_COEFF_2, /* 0 */
+ ADE_ALP_MUL_COEFF_3 /* 1 */
+};
+
+/*
+ * LDI regs relevant enums
+ */
+enum dsi_pclk_en {
+ DSI_PCLK_ON = 0,
+ DSI_PCLK_OFF
+};
+
+enum ldi_output_format {
+ LDI_OUT_RGB_565 = 0,
+ LDI_OUT_RGB_666,
+ LDI_OUT_RGB_888
+};
+
+enum ldi_work_mode {
+ TEST_MODE = 0,
+ NORMAL_MODE
+};
+
+enum ldi_input_source {
+ DISP_SRC_NONE = 0,
+ DISP_SRC_OVLY2,
+ DISP_SRC_DISP,
+ DISP_SRC_ROT,
+ DISP_SRC_SCL2
+};
+
+/*
+ * ADE media bus service relevant enums
+ */
+enum qos_generator_mode {
+ FIXED_MODE = 0,
+ LIMITER_MODE,
+ BYPASS_MODE,
+ REGULATOR_MODE
+};
+
+/*
+ * Register Write/Read Helper functions
+ */
+static inline void ade_update_bits(void __iomem *addr, u32 bit_start,
+ u32 mask, u32 val)
+{
+ u32 tmp, orig;
+
+ orig = readl(addr);
+ tmp = orig & ~(mask << bit_start);
+ tmp |= (val & mask) << bit_start;
+ writel(tmp, addr);
+}
+
+#endif
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
new file mode 100644
index 000000000000..cfbea957297b
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
@@ -0,0 +1,462 @@
+/*
+ * Hisilicon Hi6220 SoC ADE(Advanced Display Engine)'s crtc&plane driver
+ *
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * Author:
+ * Xinliang Liu <z.liuxinliang-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
+ * Xinliang Liu <xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ * Xinwei Kong <kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <video/display_timing.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "kirin_drm_drv.h"
+#include "kirin_ade_reg.h"
+
+#define to_ade_crtc(crtc) \
+ container_of(crtc, struct ade_crtc, base)
+
+struct ade_hw_ctx {
+ void __iomem *base;
+ struct regmap *noc_regmap;
+ struct clk *ade_core_clk;
+ struct clk *media_noc_clk;
+ struct clk *ade_pix_clk;
+ struct reset_control *reset;
+ bool power_on;
+ int irq;
+};
+
+struct ade_crtc {
+ struct drm_crtc base;
+ struct ade_hw_ctx *ctx;
+ bool enable;
+ u32 out_format;
+};
+
+struct ade_data {
+ struct ade_crtc acrtc;
+ struct ade_hw_ctx ctx;
+};
+
+static void ade_update_reload_bit(void __iomem *base, u32 bit_num, u32 val)
+{
+ u32 bit_ofst, reg_num;
+
+ bit_ofst = bit_num % 32;
+ reg_num = bit_num / 32;
+
+ ade_update_bits(base + ADE_RELOAD_DIS(reg_num), bit_ofst,
+ MASK(1), !!val);
+}
+
+static u32 ade_read_reload_bit(void __iomem *base, u32 bit_num)
+{
+ u32 tmp, bit_ofst, reg_num;
+
+ bit_ofst = bit_num % 32;
+ reg_num = bit_num / 32;
+
+ tmp = readl(base + ADE_RELOAD_DIS(reg_num));
+ return !!(BIT(bit_ofst) & tmp);
+}
+
+static void ade_init(struct ade_hw_ctx *ctx)
+{
+ void __iomem *base = ctx->base;
+
+ /* enable clk gate */
+ ade_update_bits(base + ADE_CTRL1, AUTO_CLK_GATE_EN_OFST,
+ AUTO_CLK_GATE_EN, ADE_ENABLE);
+ /* clear overlay */
+ writel(0, base + ADE_OVLY1_TRANS_CFG);
+ writel(0, base + ADE_OVLY_CTL);
+ writel(0, base + ADE_OVLYX_CTL(ADE_OVLY2));
+ /* clear reset and reload regs */
+ writel(MASK(32), base + ADE_SOFT_RST_SEL(0));
+ writel(MASK(32), base + ADE_SOFT_RST_SEL(1));
+ writel(MASK(32), base + ADE_RELOAD_DIS(0));
+ writel(MASK(32), base + ADE_RELOAD_DIS(1));
+ /*
+ * for video mode, all the ade registers should
+ * become effective at frame end.
+ */
+ ade_update_bits(base + ADE_CTRL, FRM_END_START_OFST,
+ FRM_END_START_MASK, REG_EFFECTIVE_IN_ADEEN_FRMEND);
+}
+
+static void ade_set_pix_clk(struct ade_hw_ctx *ctx,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ u32 clk_Hz = mode->clock * 1000;
+ int ret;
+
+ /*
+ * Success should be guaranteed in mode_valid call back,
+ * so failure shouldn't happen here
+ */
+ ret = clk_set_rate(ctx->ade_pix_clk, clk_Hz);
+ if (ret)
+ DRM_ERROR("failed to set pixel clk %dHz (%d)\n", clk_Hz, ret);
+ adj_mode->clock = clk_get_rate(ctx->ade_pix_clk) / 1000;
+}
+
+static void ade_ldi_set_mode(struct ade_crtc *acrtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+ u32 width = mode->hdisplay;
+ u32 height = mode->vdisplay;
+ u32 hfp, hbp, hsw, vfp, vbp, vsw;
+ u32 plr_flags;
+
+ plr_flags = (mode->flags & DRM_MODE_FLAG_NVSYNC) ? FLAG_NVSYNC : 0;
+ plr_flags |= (mode->flags & DRM_MODE_FLAG_NHSYNC) ? FLAG_NHSYNC : 0;
+ hfp = mode->hsync_start - mode->hdisplay;
+ hbp = mode->htotal - mode->hsync_end;
+ hsw = mode->hsync_end - mode->hsync_start;
+ vfp = mode->vsync_start - mode->vdisplay;
+ vbp = mode->vtotal - mode->vsync_end;
+ vsw = mode->vsync_end - mode->vsync_start;
+ if (vsw > 15) {
+ DRM_DEBUG_DRIVER("vsw exceeded 15\n");
+ vsw = 15;
+ }
+
+ writel((hbp << HBP_OFST) | hfp, base + LDI_HRZ_CTRL0);
+ /* the configured value is actual value - 1 */
+ writel(hsw - 1, base + LDI_HRZ_CTRL1);
+ writel((vbp << VBP_OFST) | vfp, base + LDI_VRT_CTRL0);
+ /* the configured value is actual value - 1 */
+ writel(vsw - 1, base + LDI_VRT_CTRL1);
+ /* the configured value is actual value - 1 */
+ writel(((height - 1) << VSIZE_OFST) | (width - 1),
+ base + LDI_DSP_SIZE);
+ writel(plr_flags, base + LDI_PLR_CTRL);
+
+ /* ctran6 setting */
+ writel(CTRAN_BYPASS_ON, base + ADE_CTRAN_DIS(ADE_CTRAN6));
+ /* the configured value is actual value - 1 */
+ writel(width * height - 1, base + ADE_CTRAN_IMAGE_SIZE(ADE_CTRAN6));
+ ade_update_reload_bit(base, CTRAN_OFST + ADE_CTRAN6, 0);
+
+ ade_set_pix_clk(ctx, mode, adj_mode);
+
+ DRM_DEBUG_DRIVER("set mode: %dx%d\n", width, height);
+}
+
+static int ade_power_up(struct ade_hw_ctx *ctx)
+{
+ int ret;
+
+ ret = clk_prepare_enable(ctx->media_noc_clk);
+ if (ret) {
+ DRM_ERROR("failed to enable media_noc_clk (%d)\n", ret);
+ return ret;
+ }
+
+ ret = reset_control_deassert(ctx->reset);
+ if (ret) {
+ DRM_ERROR("failed to deassert reset\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(ctx->ade_core_clk);
+ if (ret) {
+ DRM_ERROR("failed to enable ade_core_clk (%d)\n", ret);
+ return ret;
+ }
+
+ ade_init(ctx);
+ ctx->power_on = true;
+ return 0;
+}
+
+static void ade_power_down(struct ade_hw_ctx *ctx)
+{
+ void __iomem *base = ctx->base;
+
+ writel(ADE_DISABLE, base + LDI_CTRL);
+ /* dsi pixel off */
+ writel(DSI_PCLK_OFF, base + LDI_HDMI_DSI_GT);
+
+ clk_disable_unprepare(ctx->ade_core_clk);
+ reset_control_assert(ctx->reset);
+ clk_disable_unprepare(ctx->media_noc_clk);
+ ctx->power_on = false;
+}
+
+static void ade_set_medianoc_qos(struct ade_crtc *acrtc)
+{
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ struct regmap *map = ctx->noc_regmap;
+
+ regmap_update_bits(map, ADE0_QOSGENERATOR_MODE,
+ QOSGENERATOR_MODE_MASK, BYPASS_MODE);
+ regmap_update_bits(map, ADE0_QOSGENERATOR_EXTCONTROL,
+ SOCKET_QOS_EN, SOCKET_QOS_EN);
+
+ regmap_update_bits(map, ADE1_QOSGENERATOR_MODE,
+ QOSGENERATOR_MODE_MASK, BYPASS_MODE);
+ regmap_update_bits(map, ADE1_QOSGENERATOR_EXTCONTROL,
+ SOCKET_QOS_EN, SOCKET_QOS_EN);
+}
+
+static void ade_display_enable(struct ade_crtc *acrtc)
+{
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+ u32 out_fmt = acrtc->out_format;
+
+ /* display source setting */
+ writel(DISP_SRC_OVLY2, base + ADE_DISP_SRC_CFG);
+
+ /* enable ade */
+ writel(ADE_ENABLE, base + ADE_EN);
+ /* enable ldi */
+ writel(NORMAL_MODE, base + LDI_WORK_MODE);
+ writel((out_fmt << BPP_OFST) | DATA_GATE_EN | LDI_EN,
+ base + LDI_CTRL);
+ /* dsi pixel on */
+ writel(DSI_PCLK_ON, base + LDI_HDMI_DSI_GT);
+}
+
+static void ade_crtc_enable(struct drm_crtc *crtc)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ int ret;
+
+ if (acrtc->enable)
+ return;
+
+ if (!ctx->power_on) {
+ ret = ade_power_up(ctx);
+ if (ret)
+ return;
+ }
+
+ ade_set_medianoc_qos(acrtc);
+ ade_display_enable(acrtc);
+ acrtc->enable = true;
+}
+
+static void ade_crtc_disable(struct drm_crtc *crtc)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+
+ if (!acrtc->enable)
+ return;
+
+ ade_power_down(ctx);
+ acrtc->enable = false;
+}
+
+static int ade_crtc_atomic_check(struct drm_crtc *crtc,
+ struct drm_crtc_state *state)
+{
+ /* do nothing */
+ return 0;
+}
+
+static void ade_crtc_mode_set_nofb(struct drm_crtc *crtc)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ struct drm_display_mode *mode = &crtc->state->mode;
+ struct drm_display_mode *adj_mode = &crtc->state->adjusted_mode;
+
+ if (!ctx->power_on)
+ (void)ade_power_up(ctx);
+ ade_ldi_set_mode(acrtc, mode, adj_mode);
+}
+
+static void ade_crtc_atomic_begin(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+
+ if (!ctx->power_on)
+ (void)ade_power_up(ctx);
+}
+
+static void ade_crtc_atomic_flush(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+
+ /* only crtc is enabled regs take effect */
+ if (acrtc->enable) {
+ /* flush ade registers */
+ writel(ADE_ENABLE, base + ADE_EN);
+ }
+}
+
+static const struct drm_crtc_helper_funcs ade_crtc_helper_funcs = {
+ .enable = ade_crtc_enable,
+ .disable = ade_crtc_disable,
+ .atomic_check = ade_crtc_atomic_check,
+ .mode_set_nofb = ade_crtc_mode_set_nofb,
+ .atomic_begin = ade_crtc_atomic_begin,
+ .atomic_flush = ade_crtc_atomic_flush,
+};
+
+static const struct drm_crtc_funcs ade_crtc_funcs = {
+ .destroy = drm_crtc_cleanup,
+ .set_config = drm_atomic_helper_set_config,
+ .page_flip = drm_atomic_helper_page_flip,
+ .reset = drm_atomic_helper_crtc_reset,
+ .set_property = drm_atomic_helper_crtc_set_property,
+ .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
+};
+
+static int ade_crtc_init(struct drm_device *dev, struct drm_crtc *crtc,
+ struct drm_plane *plane)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+ struct device_node *port;
+ int ret;
+
+ /* set crtc port so that
+ * drm_of_find_possible_crtcs call works
+ */
+ port = of_get_child_by_name(dev->dev->of_node, "port");
+ if (!port) {
+ DRM_ERROR("no port node found in %s\n",
+ dev->dev->of_node->full_name);
+ return -EINVAL;
+ }
+ of_node_put(port);
+ crtc->port = port;
+
+ ret = drm_crtc_init_with_planes(dev, crtc, plane, NULL,
+ &ade_crtc_funcs, NULL);
+ if (ret) {
+ DRM_ERROR("failed to init crtc.\n");
+ return ret;
+ }
+
+ drm_crtc_helper_add(crtc, &ade_crtc_helper_funcs);
+ priv->crtc[drm_crtc_index(crtc)] = crtc;
+
+ return 0;
+}
+
+static int ade_dts_parse(struct platform_device *pdev, struct ade_hw_ctx *ctx)
+{
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = pdev->dev.of_node;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ctx->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(ctx->base)) {
+ DRM_ERROR("failed to remap ade io base\n");
+ return PTR_ERR(ctx->base);
+ }
+
+ ctx->reset = devm_reset_control_get(dev, NULL);
+ if (IS_ERR(ctx->reset))
+ return PTR_ERR(ctx->reset);
+
+ ctx->noc_regmap =
+ syscon_regmap_lookup_by_phandle(np, "hisilicon,noc-syscon");
+ if (IS_ERR(ctx->noc_regmap)) {
+ DRM_ERROR("failed to get noc regmap\n");
+ return PTR_ERR(ctx->noc_regmap);
+ }
+
+ ctx->irq = platform_get_irq(pdev, 0);
+ if (ctx->irq < 0) {
+ DRM_ERROR("failed to get irq\n");
+ return -ENODEV;
+ }
+
+ ctx->ade_core_clk = devm_clk_get(dev, "clk_ade_core");
+ if (!ctx->ade_core_clk) {
+ DRM_ERROR("failed to parse clk ADE_CORE\n");
+ return -ENODEV;
+ }
+
+ ctx->media_noc_clk = devm_clk_get(dev, "clk_codec_jpeg");
+ if (!ctx->media_noc_clk) {
+ DRM_ERROR("failed to parse clk CODEC_JPEG\n");
+ return -ENODEV;
+ }
+
+ ctx->ade_pix_clk = devm_clk_get(dev, "clk_ade_pix");
+ if (!ctx->ade_pix_clk) {
+ DRM_ERROR("failed to parse clk ADE_PIX\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int ade_drm_init(struct drm_device *dev)
+{
+ struct platform_device *pdev = dev->platformdev;
+ struct ade_data *ade;
+ struct ade_hw_ctx *ctx;
+ struct ade_crtc *acrtc;
+ int ret;
+
+ ade = devm_kzalloc(dev->dev, sizeof(*ade), GFP_KERNEL);
+ if (!ade) {
+ DRM_ERROR("failed to alloc ade_data\n");
+ return -ENOMEM;
+ }
+ platform_set_drvdata(pdev, ade);
+
+ ctx = &ade->ctx;
+ acrtc = &ade->acrtc;
+ acrtc->ctx = ctx;
+ acrtc->out_format = LDI_OUT_RGB_888;
+
+ ret = ade_dts_parse(pdev, ctx);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void ade_drm_cleanup(struct drm_device *dev)
+{
+ struct platform_device *pdev = dev->platformdev;
+ struct ade_data *ade = platform_get_drvdata(pdev);
+ struct drm_crtc *crtc = &ade->acrtc.base;
+
+ drm_crtc_cleanup(crtc);
+}
+
+const struct kirin_dc_ops ade_dc_ops = {
+ .init = ade_drm_init,
+ .cleanup = ade_drm_cleanup
+};
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
index 976c9b1a3fd3..578a1eb94517 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -30,8 +30,12 @@ static struct kirin_dc_ops *dc_ops;
static int kirin_drm_kms_cleanup(struct drm_device *dev)
{
+ struct kirin_drm_private *priv = dev->dev_private;
+
dc_ops->cleanup(dev);
drm_mode_config_cleanup(dev);
+ devm_kfree(dev->dev, priv);
+ dev->dev_private = NULL;
return 0;
}
@@ -55,8 +59,14 @@ static void kirin_drm_mode_config_init(struct drm_device *dev)
static int kirin_drm_kms_init(struct drm_device *dev)
{
+ struct kirin_drm_private *priv;
int ret;
+ priv = devm_kzalloc(dev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ dev->dev_private = priv;
dev_set_drvdata(dev->dev, dev);
/* dev->mode_config initialization */
@@ -84,6 +94,8 @@ err_dc_cleanup:
dc_ops->cleanup(dev);
err_mode_config_cleanup:
drm_mode_config_cleanup(dev);
+ devm_kfree(dev->dev, priv);
+ dev->dev_private = NULL;
return ret;
}
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
index 75e9d82356d4..5a05ad6a81db 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
@@ -11,10 +11,18 @@
#ifndef __KIRIN_DRM_DRV_H__
#define __KIRIN_DRM_DRV_H__
+#define MAX_CRTC 2
+
/* display controller init/cleanup ops */
struct kirin_dc_ops {
int (*init)(struct drm_device *dev);
void (*cleanup)(struct drm_device *dev);
};
+struct kirin_drm_private {
+ struct drm_crtc *crtc[MAX_CRTC];
+};
+
+extern const struct kirin_dc_ops ade_dc_ops;
+
#endif /* __KIRIN_DRM_DRV_H__ */
--
2.8.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 03/10] drm/hisilicon: Add crtc driver for ADE
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add crtc funcs and helper funcs for ADE.
v8: None.
v7:
- A few Regs define clean up and typo fixs.
v6:
- Cleanup reg-names dt parsing.
v5:
- Use syscon to access ADE media NOC QoS registers instread of directly
writing registers.
- Use reset controller to reset ADE instead of directly writing registers.
v4: None.
v3:
- Make ade as the master driver.
- Use port to connect with encoder.
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
---
drivers/gpu/drm/hisilicon/kirin/Makefile | 3 +-
drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 ++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 462 ++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 12 +
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 8 +
5 files changed, 714 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
diff --git a/drivers/gpu/drm/hisilicon/kirin/Makefile b/drivers/gpu/drm/hisilicon/kirin/Makefile
index cb346de47d48..2a61ab006ddb 100644
--- a/drivers/gpu/drm/hisilicon/kirin/Makefile
+++ b/drivers/gpu/drm/hisilicon/kirin/Makefile
@@ -1,3 +1,4 @@
-kirin-drm-y := kirin_drm_drv.o
+kirin-drm-y := kirin_drm_drv.o \
+ kirin_drm_ade.o
obj-$(CONFIG_DRM_HISI_KIRIN) += kirin-drm.o
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h b/drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
new file mode 100644
index 000000000000..4cf281b7ed63
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
@@ -0,0 +1,230 @@
+/*
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __KIRIN_ADE_REG_H__
+#define __KIRIN_ADE_REG_H__
+
+/*
+ * ADE Registers
+ */
+#define MASK(x) (BIT(x) - 1)
+
+#define ADE_CTRL 0x0004
+#define FRM_END_START_OFST 0
+#define FRM_END_START_MASK MASK(2)
+#define AUTO_CLK_GATE_EN_OFST 0
+#define AUTO_CLK_GATE_EN BIT(0)
+#define ADE_DISP_SRC_CFG 0x0018
+#define ADE_CTRL1 0x008C
+#define ADE_EN 0x0100
+#define ADE_DISABLE 0
+#define ADE_ENABLE 1
+/* reset and reload regs */
+#define ADE_SOFT_RST_SEL(x) (0x0078 + (x) * 0x4)
+#define ADE_RELOAD_DIS(x) (0x00AC + (x) * 0x4)
+#define RDMA_OFST 0
+#define CLIP_OFST 15
+#define SCL_OFST 21
+#define CTRAN_OFST 24
+#define OVLY_OFST 37 /* 32+5 */
+/* channel regs */
+#define RD_CH_CTRL(x) (0x1004 + (x) * 0x80)
+#define RD_CH_ADDR(x) (0x1008 + (x) * 0x80)
+#define RD_CH_SIZE(x) (0x100C + (x) * 0x80)
+#define RD_CH_STRIDE(x) (0x1010 + (x) * 0x80)
+#define RD_CH_SPACE(x) (0x1014 + (x) * 0x80)
+#define RD_CH_EN(x) (0x1020 + (x) * 0x80)
+/* overlay regs */
+#define ADE_OVLY1_TRANS_CFG 0x002C
+#define ADE_OVLY_CTL 0x0098
+#define ADE_OVLY_CH_XY0(x) (0x2004 + (x) * 4)
+#define ADE_OVLY_CH_XY1(x) (0x2024 + (x) * 4)
+#define ADE_OVLY_CH_CTL(x) (0x204C + (x) * 4)
+#define ADE_OVLY_OUTPUT_SIZE(x) (0x2070 + (x) * 8)
+#define OUTPUT_XSIZE_OFST 16
+#define ADE_OVLYX_CTL(x) (0x209C + (x) * 4)
+#define CH_OVLY_SEL_OFST(x) ((x) * 4)
+#define CH_OVLY_SEL_MASK MASK(2)
+#define CH_OVLY_SEL_VAL(x) ((x) + 1)
+#define CH_ALP_MODE_OFST 0
+#define CH_ALP_SEL_OFST 2
+#define CH_UNDER_ALP_SEL_OFST 4
+#define CH_EN_OFST 6
+#define CH_ALP_GBL_OFST 15
+#define CH_SEL_OFST 28
+/* ctran regs */
+#define ADE_CTRAN_DIS(x) (0x5004 + (x) * 0x100)
+#define CTRAN_BYPASS_ON 1
+#define CTRAN_BYPASS_OFF 0
+#define ADE_CTRAN_IMAGE_SIZE(x) (0x503C + (x) * 0x100)
+/* clip regs */
+#define ADE_CLIP_DISABLE(x) (0x6800 + (x) * 0x100)
+#define ADE_CLIP_SIZE0(x) (0x6804 + (x) * 0x100)
+#define ADE_CLIP_SIZE1(x) (0x6808 + (x) * 0x100)
+
+/*
+ * LDI Registers
+ */
+#define LDI_HRZ_CTRL0 0x7400
+#define HBP_OFST 20
+#define LDI_HRZ_CTRL1 0x7404
+#define LDI_VRT_CTRL0 0x7408
+#define VBP_OFST 20
+#define LDI_VRT_CTRL1 0x740C
+#define LDI_PLR_CTRL 0x7410
+#define FLAG_NVSYNC BIT(0)
+#define FLAG_NHSYNC BIT(1)
+#define FLAG_NPIXCLK BIT(2)
+#define FLAG_NDE BIT(3)
+#define LDI_DSP_SIZE 0x7414
+#define VSIZE_OFST 20
+#define LDI_INT_EN 0x741C
+#define FRAME_END_INT_EN_OFST 1
+#define LDI_CTRL 0x7420
+#define BPP_OFST 3
+#define DATA_GATE_EN BIT(2)
+#define LDI_EN BIT(0)
+#define LDI_MSK_INT 0x7428
+#define LDI_INT_CLR 0x742C
+#define LDI_WORK_MODE 0x7430
+#define LDI_HDMI_DSI_GT 0x7434
+
+/*
+ * ADE media bus service regs
+ */
+#define ADE0_QOSGENERATOR_MODE 0x010C
+#define QOSGENERATOR_MODE_MASK MASK(2)
+#define ADE0_QOSGENERATOR_EXTCONTROL 0x0118
+#define SOCKET_QOS_EN BIT(0)
+#define ADE1_QOSGENERATOR_MODE 0x020C
+#define ADE1_QOSGENERATOR_EXTCONTROL 0x0218
+
+/*
+ * ADE regs relevant enums
+ */
+enum frame_end_start {
+ /* regs take effect in every vsync */
+ REG_EFFECTIVE_IN_VSYNC = 0,
+ /* regs take effect in fist ade en and every frame end */
+ REG_EFFECTIVE_IN_ADEEN_FRMEND,
+ /* regs take effect in ade en immediately */
+ REG_EFFECTIVE_IN_ADEEN,
+ /* regs take effect in first vsync and every frame end */
+ REG_EFFECTIVE_IN_VSYNC_FRMEND
+};
+
+enum ade_fb_format {
+ ADE_RGB_565 = 0,
+ ADE_BGR_565,
+ ADE_XRGB_8888,
+ ADE_XBGR_8888,
+ ADE_ARGB_8888,
+ ADE_ABGR_8888,
+ ADE_RGBA_8888,
+ ADE_BGRA_8888,
+ ADE_RGB_888,
+ ADE_BGR_888 = 9,
+ ADE_FORMAT_UNSUPPORT = 800
+};
+
+enum ade_channel {
+ ADE_CH1 = 0, /* channel 1 for primary plane */
+ ADE_CH_NUM
+};
+
+enum ade_scale {
+ ADE_SCL1 = 0,
+ ADE_SCL2,
+ ADE_SCL3,
+ ADE_SCL_NUM
+};
+
+enum ade_ctran {
+ ADE_CTRAN1 = 0,
+ ADE_CTRAN2,
+ ADE_CTRAN3,
+ ADE_CTRAN4,
+ ADE_CTRAN5,
+ ADE_CTRAN6,
+ ADE_CTRAN_NUM
+};
+
+enum ade_overlay {
+ ADE_OVLY1 = 0,
+ ADE_OVLY2,
+ ADE_OVLY3,
+ ADE_OVLY_NUM
+};
+
+enum ade_alpha_mode {
+ ADE_ALP_GLOBAL = 0,
+ ADE_ALP_PIXEL,
+ ADE_ALP_PIXEL_AND_GLB
+};
+
+enum ade_alpha_blending_mode {
+ ADE_ALP_MUL_COEFF_0 = 0, /* alpha */
+ ADE_ALP_MUL_COEFF_1, /* 1-alpha */
+ ADE_ALP_MUL_COEFF_2, /* 0 */
+ ADE_ALP_MUL_COEFF_3 /* 1 */
+};
+
+/*
+ * LDI regs relevant enums
+ */
+enum dsi_pclk_en {
+ DSI_PCLK_ON = 0,
+ DSI_PCLK_OFF
+};
+
+enum ldi_output_format {
+ LDI_OUT_RGB_565 = 0,
+ LDI_OUT_RGB_666,
+ LDI_OUT_RGB_888
+};
+
+enum ldi_work_mode {
+ TEST_MODE = 0,
+ NORMAL_MODE
+};
+
+enum ldi_input_source {
+ DISP_SRC_NONE = 0,
+ DISP_SRC_OVLY2,
+ DISP_SRC_DISP,
+ DISP_SRC_ROT,
+ DISP_SRC_SCL2
+};
+
+/*
+ * ADE media bus service relevant enums
+ */
+enum qos_generator_mode {
+ FIXED_MODE = 0,
+ LIMITER_MODE,
+ BYPASS_MODE,
+ REGULATOR_MODE
+};
+
+/*
+ * Register Write/Read Helper functions
+ */
+static inline void ade_update_bits(void __iomem *addr, u32 bit_start,
+ u32 mask, u32 val)
+{
+ u32 tmp, orig;
+
+ orig = readl(addr);
+ tmp = orig & ~(mask << bit_start);
+ tmp |= (val & mask) << bit_start;
+ writel(tmp, addr);
+}
+
+#endif
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
new file mode 100644
index 000000000000..cfbea957297b
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
@@ -0,0 +1,462 @@
+/*
+ * Hisilicon Hi6220 SoC ADE(Advanced Display Engine)'s crtc&plane driver
+ *
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * Author:
+ * Xinliang Liu <z.liuxinliang@hisilicon.com>
+ * Xinliang Liu <xinliang.liu@linaro.org>
+ * Xinwei Kong <kong.kongxinwei@hisilicon.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <video/display_timing.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "kirin_drm_drv.h"
+#include "kirin_ade_reg.h"
+
+#define to_ade_crtc(crtc) \
+ container_of(crtc, struct ade_crtc, base)
+
+struct ade_hw_ctx {
+ void __iomem *base;
+ struct regmap *noc_regmap;
+ struct clk *ade_core_clk;
+ struct clk *media_noc_clk;
+ struct clk *ade_pix_clk;
+ struct reset_control *reset;
+ bool power_on;
+ int irq;
+};
+
+struct ade_crtc {
+ struct drm_crtc base;
+ struct ade_hw_ctx *ctx;
+ bool enable;
+ u32 out_format;
+};
+
+struct ade_data {
+ struct ade_crtc acrtc;
+ struct ade_hw_ctx ctx;
+};
+
+static void ade_update_reload_bit(void __iomem *base, u32 bit_num, u32 val)
+{
+ u32 bit_ofst, reg_num;
+
+ bit_ofst = bit_num % 32;
+ reg_num = bit_num / 32;
+
+ ade_update_bits(base + ADE_RELOAD_DIS(reg_num), bit_ofst,
+ MASK(1), !!val);
+}
+
+static u32 ade_read_reload_bit(void __iomem *base, u32 bit_num)
+{
+ u32 tmp, bit_ofst, reg_num;
+
+ bit_ofst = bit_num % 32;
+ reg_num = bit_num / 32;
+
+ tmp = readl(base + ADE_RELOAD_DIS(reg_num));
+ return !!(BIT(bit_ofst) & tmp);
+}
+
+static void ade_init(struct ade_hw_ctx *ctx)
+{
+ void __iomem *base = ctx->base;
+
+ /* enable clk gate */
+ ade_update_bits(base + ADE_CTRL1, AUTO_CLK_GATE_EN_OFST,
+ AUTO_CLK_GATE_EN, ADE_ENABLE);
+ /* clear overlay */
+ writel(0, base + ADE_OVLY1_TRANS_CFG);
+ writel(0, base + ADE_OVLY_CTL);
+ writel(0, base + ADE_OVLYX_CTL(ADE_OVLY2));
+ /* clear reset and reload regs */
+ writel(MASK(32), base + ADE_SOFT_RST_SEL(0));
+ writel(MASK(32), base + ADE_SOFT_RST_SEL(1));
+ writel(MASK(32), base + ADE_RELOAD_DIS(0));
+ writel(MASK(32), base + ADE_RELOAD_DIS(1));
+ /*
+ * for video mode, all the ade registers should
+ * become effective at frame end.
+ */
+ ade_update_bits(base + ADE_CTRL, FRM_END_START_OFST,
+ FRM_END_START_MASK, REG_EFFECTIVE_IN_ADEEN_FRMEND);
+}
+
+static void ade_set_pix_clk(struct ade_hw_ctx *ctx,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ u32 clk_Hz = mode->clock * 1000;
+ int ret;
+
+ /*
+ * Success should be guaranteed in mode_valid call back,
+ * so failure shouldn't happen here
+ */
+ ret = clk_set_rate(ctx->ade_pix_clk, clk_Hz);
+ if (ret)
+ DRM_ERROR("failed to set pixel clk %dHz (%d)\n", clk_Hz, ret);
+ adj_mode->clock = clk_get_rate(ctx->ade_pix_clk) / 1000;
+}
+
+static void ade_ldi_set_mode(struct ade_crtc *acrtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+ u32 width = mode->hdisplay;
+ u32 height = mode->vdisplay;
+ u32 hfp, hbp, hsw, vfp, vbp, vsw;
+ u32 plr_flags;
+
+ plr_flags = (mode->flags & DRM_MODE_FLAG_NVSYNC) ? FLAG_NVSYNC : 0;
+ plr_flags |= (mode->flags & DRM_MODE_FLAG_NHSYNC) ? FLAG_NHSYNC : 0;
+ hfp = mode->hsync_start - mode->hdisplay;
+ hbp = mode->htotal - mode->hsync_end;
+ hsw = mode->hsync_end - mode->hsync_start;
+ vfp = mode->vsync_start - mode->vdisplay;
+ vbp = mode->vtotal - mode->vsync_end;
+ vsw = mode->vsync_end - mode->vsync_start;
+ if (vsw > 15) {
+ DRM_DEBUG_DRIVER("vsw exceeded 15\n");
+ vsw = 15;
+ }
+
+ writel((hbp << HBP_OFST) | hfp, base + LDI_HRZ_CTRL0);
+ /* the configured value is actual value - 1 */
+ writel(hsw - 1, base + LDI_HRZ_CTRL1);
+ writel((vbp << VBP_OFST) | vfp, base + LDI_VRT_CTRL0);
+ /* the configured value is actual value - 1 */
+ writel(vsw - 1, base + LDI_VRT_CTRL1);
+ /* the configured value is actual value - 1 */
+ writel(((height - 1) << VSIZE_OFST) | (width - 1),
+ base + LDI_DSP_SIZE);
+ writel(plr_flags, base + LDI_PLR_CTRL);
+
+ /* ctran6 setting */
+ writel(CTRAN_BYPASS_ON, base + ADE_CTRAN_DIS(ADE_CTRAN6));
+ /* the configured value is actual value - 1 */
+ writel(width * height - 1, base + ADE_CTRAN_IMAGE_SIZE(ADE_CTRAN6));
+ ade_update_reload_bit(base, CTRAN_OFST + ADE_CTRAN6, 0);
+
+ ade_set_pix_clk(ctx, mode, adj_mode);
+
+ DRM_DEBUG_DRIVER("set mode: %dx%d\n", width, height);
+}
+
+static int ade_power_up(struct ade_hw_ctx *ctx)
+{
+ int ret;
+
+ ret = clk_prepare_enable(ctx->media_noc_clk);
+ if (ret) {
+ DRM_ERROR("failed to enable media_noc_clk (%d)\n", ret);
+ return ret;
+ }
+
+ ret = reset_control_deassert(ctx->reset);
+ if (ret) {
+ DRM_ERROR("failed to deassert reset\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(ctx->ade_core_clk);
+ if (ret) {
+ DRM_ERROR("failed to enable ade_core_clk (%d)\n", ret);
+ return ret;
+ }
+
+ ade_init(ctx);
+ ctx->power_on = true;
+ return 0;
+}
+
+static void ade_power_down(struct ade_hw_ctx *ctx)
+{
+ void __iomem *base = ctx->base;
+
+ writel(ADE_DISABLE, base + LDI_CTRL);
+ /* dsi pixel off */
+ writel(DSI_PCLK_OFF, base + LDI_HDMI_DSI_GT);
+
+ clk_disable_unprepare(ctx->ade_core_clk);
+ reset_control_assert(ctx->reset);
+ clk_disable_unprepare(ctx->media_noc_clk);
+ ctx->power_on = false;
+}
+
+static void ade_set_medianoc_qos(struct ade_crtc *acrtc)
+{
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ struct regmap *map = ctx->noc_regmap;
+
+ regmap_update_bits(map, ADE0_QOSGENERATOR_MODE,
+ QOSGENERATOR_MODE_MASK, BYPASS_MODE);
+ regmap_update_bits(map, ADE0_QOSGENERATOR_EXTCONTROL,
+ SOCKET_QOS_EN, SOCKET_QOS_EN);
+
+ regmap_update_bits(map, ADE1_QOSGENERATOR_MODE,
+ QOSGENERATOR_MODE_MASK, BYPASS_MODE);
+ regmap_update_bits(map, ADE1_QOSGENERATOR_EXTCONTROL,
+ SOCKET_QOS_EN, SOCKET_QOS_EN);
+}
+
+static void ade_display_enable(struct ade_crtc *acrtc)
+{
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+ u32 out_fmt = acrtc->out_format;
+
+ /* display source setting */
+ writel(DISP_SRC_OVLY2, base + ADE_DISP_SRC_CFG);
+
+ /* enable ade */
+ writel(ADE_ENABLE, base + ADE_EN);
+ /* enable ldi */
+ writel(NORMAL_MODE, base + LDI_WORK_MODE);
+ writel((out_fmt << BPP_OFST) | DATA_GATE_EN | LDI_EN,
+ base + LDI_CTRL);
+ /* dsi pixel on */
+ writel(DSI_PCLK_ON, base + LDI_HDMI_DSI_GT);
+}
+
+static void ade_crtc_enable(struct drm_crtc *crtc)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ int ret;
+
+ if (acrtc->enable)
+ return;
+
+ if (!ctx->power_on) {
+ ret = ade_power_up(ctx);
+ if (ret)
+ return;
+ }
+
+ ade_set_medianoc_qos(acrtc);
+ ade_display_enable(acrtc);
+ acrtc->enable = true;
+}
+
+static void ade_crtc_disable(struct drm_crtc *crtc)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+
+ if (!acrtc->enable)
+ return;
+
+ ade_power_down(ctx);
+ acrtc->enable = false;
+}
+
+static int ade_crtc_atomic_check(struct drm_crtc *crtc,
+ struct drm_crtc_state *state)
+{
+ /* do nothing */
+ return 0;
+}
+
+static void ade_crtc_mode_set_nofb(struct drm_crtc *crtc)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ struct drm_display_mode *mode = &crtc->state->mode;
+ struct drm_display_mode *adj_mode = &crtc->state->adjusted_mode;
+
+ if (!ctx->power_on)
+ (void)ade_power_up(ctx);
+ ade_ldi_set_mode(acrtc, mode, adj_mode);
+}
+
+static void ade_crtc_atomic_begin(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+
+ if (!ctx->power_on)
+ (void)ade_power_up(ctx);
+}
+
+static void ade_crtc_atomic_flush(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_state)
+
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+
+ /* only crtc is enabled regs take effect */
+ if (acrtc->enable) {
+ /* flush ade registers */
+ writel(ADE_ENABLE, base + ADE_EN);
+ }
+}
+
+static const struct drm_crtc_helper_funcs ade_crtc_helper_funcs = {
+ .enable = ade_crtc_enable,
+ .disable = ade_crtc_disable,
+ .atomic_check = ade_crtc_atomic_check,
+ .mode_set_nofb = ade_crtc_mode_set_nofb,
+ .atomic_begin = ade_crtc_atomic_begin,
+ .atomic_flush = ade_crtc_atomic_flush,
+};
+
+static const struct drm_crtc_funcs ade_crtc_funcs = {
+ .destroy = drm_crtc_cleanup,
+ .set_config = drm_atomic_helper_set_config,
+ .page_flip = drm_atomic_helper_page_flip,
+ .reset = drm_atomic_helper_crtc_reset,
+ .set_property = drm_atomic_helper_crtc_set_property,
+ .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
+};
+
+static int ade_crtc_init(struct drm_device *dev, struct drm_crtc *crtc,
+ struct drm_plane *plane)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+ struct device_node *port;
+ int ret;
+
+ /* set crtc port so that
+ * drm_of_find_possible_crtcs call works
+ */
+ port = of_get_child_by_name(dev->dev->of_node, "port");
+ if (!port) {
+ DRM_ERROR("no port node found in %s\n",
+ dev->dev->of_node->full_name);
+ return -EINVAL;
+ }
+ of_node_put(port);
+ crtc->port = port;
+
+ ret = drm_crtc_init_with_planes(dev, crtc, plane, NULL,
+ &ade_crtc_funcs, NULL);
+ if (ret) {
+ DRM_ERROR("failed to init crtc.\n");
+ return ret;
+ }
+
+ drm_crtc_helper_add(crtc, &ade_crtc_helper_funcs);
+ priv->crtc[drm_crtc_index(crtc)] = crtc;
+
+ return 0;
+}
+
+static int ade_dts_parse(struct platform_device *pdev, struct ade_hw_ctx *ctx)
+{
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = pdev->dev.of_node;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ctx->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(ctx->base)) {
+ DRM_ERROR("failed to remap ade io base\n");
+ return PTR_ERR(ctx->base);
+ }
+
+ ctx->reset = devm_reset_control_get(dev, NULL);
+ if (IS_ERR(ctx->reset))
+ return PTR_ERR(ctx->reset);
+
+ ctx->noc_regmap =
+ syscon_regmap_lookup_by_phandle(np, "hisilicon,noc-syscon");
+ if (IS_ERR(ctx->noc_regmap)) {
+ DRM_ERROR("failed to get noc regmap\n");
+ return PTR_ERR(ctx->noc_regmap);
+ }
+
+ ctx->irq = platform_get_irq(pdev, 0);
+ if (ctx->irq < 0) {
+ DRM_ERROR("failed to get irq\n");
+ return -ENODEV;
+ }
+
+ ctx->ade_core_clk = devm_clk_get(dev, "clk_ade_core");
+ if (!ctx->ade_core_clk) {
+ DRM_ERROR("failed to parse clk ADE_CORE\n");
+ return -ENODEV;
+ }
+
+ ctx->media_noc_clk = devm_clk_get(dev, "clk_codec_jpeg");
+ if (!ctx->media_noc_clk) {
+ DRM_ERROR("failed to parse clk CODEC_JPEG\n");
+ return -ENODEV;
+ }
+
+ ctx->ade_pix_clk = devm_clk_get(dev, "clk_ade_pix");
+ if (!ctx->ade_pix_clk) {
+ DRM_ERROR("failed to parse clk ADE_PIX\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int ade_drm_init(struct drm_device *dev)
+{
+ struct platform_device *pdev = dev->platformdev;
+ struct ade_data *ade;
+ struct ade_hw_ctx *ctx;
+ struct ade_crtc *acrtc;
+ int ret;
+
+ ade = devm_kzalloc(dev->dev, sizeof(*ade), GFP_KERNEL);
+ if (!ade) {
+ DRM_ERROR("failed to alloc ade_data\n");
+ return -ENOMEM;
+ }
+ platform_set_drvdata(pdev, ade);
+
+ ctx = &ade->ctx;
+ acrtc = &ade->acrtc;
+ acrtc->ctx = ctx;
+ acrtc->out_format = LDI_OUT_RGB_888;
+
+ ret = ade_dts_parse(pdev, ctx);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void ade_drm_cleanup(struct drm_device *dev)
+{
+ struct platform_device *pdev = dev->platformdev;
+ struct ade_data *ade = platform_get_drvdata(pdev);
+ struct drm_crtc *crtc = &ade->acrtc.base;
+
+ drm_crtc_cleanup(crtc);
+}
+
+const struct kirin_dc_ops ade_dc_ops = {
+ .init = ade_drm_init,
+ .cleanup = ade_drm_cleanup
+};
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
index 976c9b1a3fd3..578a1eb94517 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -30,8 +30,12 @@ static struct kirin_dc_ops *dc_ops;
static int kirin_drm_kms_cleanup(struct drm_device *dev)
{
+ struct kirin_drm_private *priv = dev->dev_private;
+
dc_ops->cleanup(dev);
drm_mode_config_cleanup(dev);
+ devm_kfree(dev->dev, priv);
+ dev->dev_private = NULL;
return 0;
}
@@ -55,8 +59,14 @@ static void kirin_drm_mode_config_init(struct drm_device *dev)
static int kirin_drm_kms_init(struct drm_device *dev)
{
+ struct kirin_drm_private *priv;
int ret;
+ priv = devm_kzalloc(dev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ dev->dev_private = priv;
dev_set_drvdata(dev->dev, dev);
/* dev->mode_config initialization */
@@ -84,6 +94,8 @@ err_dc_cleanup:
dc_ops->cleanup(dev);
err_mode_config_cleanup:
drm_mode_config_cleanup(dev);
+ devm_kfree(dev->dev, priv);
+ dev->dev_private = NULL;
return ret;
}
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
index 75e9d82356d4..5a05ad6a81db 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
@@ -11,10 +11,18 @@
#ifndef __KIRIN_DRM_DRV_H__
#define __KIRIN_DRM_DRV_H__
+#define MAX_CRTC 2
+
/* display controller init/cleanup ops */
struct kirin_dc_ops {
int (*init)(struct drm_device *dev);
void (*cleanup)(struct drm_device *dev);
};
+struct kirin_drm_private {
+ struct drm_crtc *crtc[MAX_CRTC];
+};
+
+extern const struct kirin_dc_ops ade_dc_ops;
+
#endif /* __KIRIN_DRM_DRV_H__ */
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 04/10] drm/hisilicon: Add plane driver for ADE
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA, daniel-/w4YWyX8dFk,
robh-DgEjT+Ai2ygdnm+yROfE0A, daniel-rLtY4a/8tF1rovVCs/uTlw,
architt-sgV2jX0FEOL9JmXXK+q4OQ, airlied-cv59FeDIM0c,
corbet-T1hC0tSOHrs, catalin.marinas-5wv7dgnIgG8,
will.deacon-5wv7dgnIgG8, emil.l.velikov-Re5JQEeQqe8AvxtiuMwx3w,
mark.rutland-5wv7dgnIgG8
Cc: linux-doc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linuxarm-hv44wF8Li93QT0dZR+AlfA,
andy.green-QSEj5FYQhm4dnm+yROfE0A,
haojian.zhuang-QSEj5FYQhm4dnm+yROfE0A,
liguozhu-C8/M+/jPZTeaMJb+Lgu22Q, xuwei5-C8/M+/jPZTeaMJb+Lgu22Q,
w.f-hv44wF8Li93QT0dZR+AlfA, puck.chen-C8/M+/jPZTeaMJb+Lgu22Q,
bintian.wang-hv44wF8Li93QT0dZR+AlfA,
benjamin.gaignard-QSEj5FYQhm4dnm+yROfE0A,
xuyiping-C8/M+/jPZTeaMJb+Lgu22Q,
kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q,
zourongrong-hv44wF8Li93QT0dZR+AlfA,
lijianhua-hv44wF8Li93QT0dZR+AlfA,
sumit.semwal-QSEj5FYQhm4dnm+yROfE0A,
guodong.xu-QSEj5FYQhm4dnm+yROfE0A, Xinliang Liu
Add plane funcs and helper funcs for ADE.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3:
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
---
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 535 +++++++++++++++++++++++-
1 file changed, 534 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
index cfbea957297b..8a7cb5e04bf4 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
@@ -27,13 +27,23 @@
#include <drm/drm_crtc_helper.h>
#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
+#include <drm/drm_plane_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_cma_helper.h>
#include "kirin_drm_drv.h"
#include "kirin_ade_reg.h"
+#define PRIMARY_CH ADE_CH1 /* primary plane */
+#define OUT_OVLY ADE_OVLY2 /* output overlay compositor */
+#define ADE_DEBUG 1
+
#define to_ade_crtc(crtc) \
container_of(crtc, struct ade_crtc, base)
+#define to_ade_plane(plane) \
+ container_of(plane, struct ade_plane, base)
+
struct ade_hw_ctx {
void __iomem *base;
struct regmap *noc_regmap;
@@ -52,11 +62,76 @@ struct ade_crtc {
u32 out_format;
};
+struct ade_plane {
+ struct drm_plane base;
+ void *ctx;
+ u8 ch; /* channel */
+};
+
struct ade_data {
struct ade_crtc acrtc;
+ struct ade_plane aplane[ADE_CH_NUM];
struct ade_hw_ctx ctx;
};
+/* ade-format info: */
+struct ade_format {
+ u32 pixel_format;
+ enum ade_fb_format ade_format;
+};
+
+static const struct ade_format ade_formats[] = {
+ /* 16bpp RGB: */
+ { DRM_FORMAT_RGB565, ADE_RGB_565 },
+ { DRM_FORMAT_BGR565, ADE_BGR_565 },
+ /* 24bpp RGB: */
+ { DRM_FORMAT_RGB888, ADE_RGB_888 },
+ { DRM_FORMAT_BGR888, ADE_BGR_888 },
+ /* 32bpp [A]RGB: */
+ { DRM_FORMAT_XRGB8888, ADE_XRGB_8888 },
+ { DRM_FORMAT_XBGR8888, ADE_XBGR_8888 },
+ { DRM_FORMAT_RGBA8888, ADE_RGBA_8888 },
+ { DRM_FORMAT_BGRA8888, ADE_BGRA_8888 },
+ { DRM_FORMAT_ARGB8888, ADE_ARGB_8888 },
+ { DRM_FORMAT_ABGR8888, ADE_ABGR_8888 },
+};
+
+static const u32 channel_formats1[] = {
+ /* channel 1,2,3,4 */
+ DRM_FORMAT_RGB565, DRM_FORMAT_BGR565, DRM_FORMAT_RGB888,
+ DRM_FORMAT_BGR888, DRM_FORMAT_XRGB8888, DRM_FORMAT_XBGR8888,
+ DRM_FORMAT_RGBA8888, DRM_FORMAT_BGRA8888, DRM_FORMAT_ARGB8888,
+ DRM_FORMAT_ABGR8888
+};
+
+u32 ade_get_channel_formats(u8 ch, const u32 **formats)
+{
+ switch (ch) {
+ case ADE_CH1:
+ *formats = channel_formats1;
+ return ARRAY_SIZE(channel_formats1);
+ default:
+ DRM_ERROR("no this channel %d\n", ch);
+ *formats = NULL;
+ return 0;
+ }
+}
+
+/* convert from fourcc format to ade format */
+static u32 ade_get_format(u32 pixel_format)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ade_formats); i++)
+ if (ade_formats[i].pixel_format == pixel_format)
+ return ade_formats[i].ade_format;
+
+ /* not found */
+ DRM_ERROR("Not found pixel format!!fourcc_format= %d\n",
+ pixel_format);
+ return ADE_FORMAT_UNSUPPORT;
+}
+
static void ade_update_reload_bit(void __iomem *base, u32 bit_num, u32 val)
{
u32 bit_ofst, reg_num;
@@ -89,7 +164,7 @@ static void ade_init(struct ade_hw_ctx *ctx)
/* clear overlay */
writel(0, base + ADE_OVLY1_TRANS_CFG);
writel(0, base + ADE_OVLY_CTL);
- writel(0, base + ADE_OVLYX_CTL(ADE_OVLY2));
+ writel(0, base + ADE_OVLYX_CTL(OUT_OVLY));
/* clear reset and reload regs */
writel(MASK(32), base + ADE_SOFT_RST_SEL(0));
writel(MASK(32), base + ADE_SOFT_RST_SEL(1));
@@ -155,6 +230,10 @@ static void ade_ldi_set_mode(struct ade_crtc *acrtc,
base + LDI_DSP_SIZE);
writel(plr_flags, base + LDI_PLR_CTRL);
+ /* set overlay compositor output size */
+ writel(((width - 1) << OUTPUT_XSIZE_OFST) | (height - 1),
+ base + ADE_OVLY_OUTPUT_SIZE(OUT_OVLY));
+
/* ctran6 setting */
writel(CTRAN_BYPASS_ON, base + ADE_CTRAN_DIS(ADE_CTRAN6));
/* the configured value is actual value - 1 */
@@ -229,6 +308,10 @@ static void ade_display_enable(struct ade_crtc *acrtc)
void __iomem *base = ctx->base;
u32 out_fmt = acrtc->out_format;
+ /* enable output overlay compositor */
+ writel(ADE_ENABLE, base + ADE_OVLYX_CTL(OUT_OVLY));
+ ade_update_reload_bit(base, OVLY_OFST + OUT_OVLY, 0);
+
/* display source setting */
writel(DISP_SRC_OVLY2, base + ADE_DISP_SRC_CFG);
@@ -242,6 +325,97 @@ static void ade_display_enable(struct ade_crtc *acrtc)
writel(DSI_PCLK_ON, base + LDI_HDMI_DSI_GT);
}
+#if ADE_DEBUG
+static void ade_rdma_dump_regs(void __iomem *base, u32 ch)
+{
+ u32 reg_ctrl, reg_addr, reg_size, reg_stride, reg_space, reg_en;
+ u32 val;
+
+ reg_ctrl = RD_CH_CTRL(ch);
+ reg_addr = RD_CH_ADDR(ch);
+ reg_size = RD_CH_SIZE(ch);
+ reg_stride = RD_CH_STRIDE(ch);
+ reg_space = RD_CH_SPACE(ch);
+ reg_en = RD_CH_EN(ch);
+
+ val = ade_read_reload_bit(base, RDMA_OFST + ch);
+ DRM_DEBUG_DRIVER("[rdma%d]: reload(%d)\n", ch + 1, val);
+ val = readl(base + reg_ctrl);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_ctrl(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_addr);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_addr(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_size);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_size(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_stride);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_stride(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_space);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_space(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_en);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_en(0x%08x)\n", ch + 1, val);
+}
+
+static void ade_clip_dump_regs(void __iomem *base, u32 ch)
+{
+ u32 val;
+
+ val = ade_read_reload_bit(base, CLIP_OFST + ch);
+ DRM_DEBUG_DRIVER("[clip%d]: reload(%d)\n", ch + 1, val);
+ val = readl(base + ADE_CLIP_DISABLE(ch));
+ DRM_DEBUG_DRIVER("[clip%d]: reg_clip_disable(0x%08x)\n", ch + 1, val);
+ val = readl(base + ADE_CLIP_SIZE0(ch));
+ DRM_DEBUG_DRIVER("[clip%d]: reg_clip_size0(0x%08x)\n", ch + 1, val);
+ val = readl(base + ADE_CLIP_SIZE1(ch));
+ DRM_DEBUG_DRIVER("[clip%d]: reg_clip_size1(0x%08x)\n", ch + 1, val);
+}
+
+static void ade_compositor_routing_dump_regs(void __iomem *base, u32 ch)
+{
+ u8 ovly_ch = 0; /* TODO: Only primary plane now */
+ u32 val;
+
+ val = readl(base + ADE_OVLY_CH_XY0(ovly_ch));
+ DRM_DEBUG_DRIVER("[overlay ch%d]: reg_ch_xy0(0x%08x)\n", ovly_ch, val);
+ val = readl(base + ADE_OVLY_CH_XY1(ovly_ch));
+ DRM_DEBUG_DRIVER("[overlay ch%d]: reg_ch_xy1(0x%08x)\n", ovly_ch, val);
+ val = readl(base + ADE_OVLY_CH_CTL(ovly_ch));
+ DRM_DEBUG_DRIVER("[overlay ch%d]: reg_ch_ctl(0x%08x)\n", ovly_ch, val);
+}
+
+static void ade_dump_overlay_compositor_regs(void __iomem *base, u32 comp)
+{
+ u32 val;
+
+ val = ade_read_reload_bit(base, OVLY_OFST + comp);
+ DRM_DEBUG_DRIVER("[overlay%d]: reload(%d)\n", comp + 1, val);
+ writel(ADE_ENABLE, base + ADE_OVLYX_CTL(comp));
+ DRM_DEBUG_DRIVER("[overlay%d]: reg_ctl(0x%08x)\n", comp + 1, val);
+ val = readl(base + ADE_OVLY_CTL);
+ DRM_DEBUG_DRIVER("ovly_ctl(0x%08x)\n", val);
+}
+
+static void ade_dump_regs(void __iomem *base)
+{
+ u32 i;
+
+ /* dump channel regs */
+ for (i = 0; i < ADE_CH_NUM; i++) {
+ /* dump rdma regs */
+ ade_rdma_dump_regs(base, i);
+
+ /* dump clip regs */
+ ade_clip_dump_regs(base, i);
+
+ /* dump compositor routing regs */
+ ade_compositor_routing_dump_regs(base, i);
+ }
+
+ /* dump overlay compositor regs */
+ ade_dump_overlay_compositor_regs(base, OUT_OVLY);
+}
+#else
+static void ade_dump_regs(void __iomem *base) { }
+#endif
+
static void ade_crtc_enable(struct drm_crtc *crtc)
{
struct ade_crtc *acrtc = to_ade_crtc(crtc);
@@ -259,6 +433,7 @@ static void ade_crtc_enable(struct drm_crtc *crtc)
ade_set_medianoc_qos(acrtc);
ade_display_enable(acrtc);
+ ade_dump_regs(ctx->base);
acrtc->enable = true;
}
@@ -313,6 +488,7 @@ static void ade_crtc_atomic_flush(struct drm_crtc *crtc,
/* only crtc is enabled regs take effect */
if (acrtc->enable) {
+ ade_dump_regs(base);
/* flush ade registers */
writel(ADE_ENABLE, base + ADE_EN);
}
@@ -369,6 +545,338 @@ static int ade_crtc_init(struct drm_device *dev, struct drm_crtc *crtc,
return 0;
}
+static void ade_rdma_set(void __iomem *base, struct drm_framebuffer *fb,
+ u32 ch, u32 y, u32 in_h, u32 fmt)
+{
+ struct drm_gem_cma_object *obj = drm_fb_cma_get_gem_obj(fb, 0);
+ u32 reg_ctrl, reg_addr, reg_size, reg_stride, reg_space, reg_en;
+ u32 stride = fb->pitches[0];
+ u32 addr = (u32)obj->paddr + y * stride;
+
+ DRM_DEBUG_DRIVER("rdma%d: (y=%d, height=%d), stride=%d, paddr=0x%x\n",
+ ch + 1, y, in_h, stride, (u32)obj->paddr);
+ DRM_DEBUG_DRIVER("addr=0x%x, fb:%dx%d, pixel_format=%d(%s)\n",
+ addr, fb->width, fb->height, fmt,
+ drm_get_format_name(fb->pixel_format));
+
+ /* get reg offset */
+ reg_ctrl = RD_CH_CTRL(ch);
+ reg_addr = RD_CH_ADDR(ch);
+ reg_size = RD_CH_SIZE(ch);
+ reg_stride = RD_CH_STRIDE(ch);
+ reg_space = RD_CH_SPACE(ch);
+ reg_en = RD_CH_EN(ch);
+
+ /*
+ * TODO: set rotation
+ */
+ writel((fmt << 16) & 0x1f0000, base + reg_ctrl);
+ writel(addr, base + reg_addr);
+ writel((in_h << 16) | stride, base + reg_size);
+ writel(stride, base + reg_stride);
+ writel(in_h * stride, base + reg_space);
+ writel(ADE_ENABLE, base + reg_en);
+ ade_update_reload_bit(base, RDMA_OFST + ch, 0);
+}
+
+static void ade_rdma_disable(void __iomem *base, u32 ch)
+{
+ u32 reg_en;
+
+ /* get reg offset */
+ reg_en = RD_CH_EN(ch);
+ writel(0, base + reg_en);
+ ade_update_reload_bit(base, RDMA_OFST + ch, 1);
+}
+
+static void ade_clip_set(void __iomem *base, u32 ch, u32 fb_w, u32 x,
+ u32 in_w, u32 in_h)
+{
+ u32 disable_val;
+ u32 clip_left;
+ u32 clip_right;
+
+ /*
+ * clip width, no need to clip height
+ */
+ if (fb_w == in_w) { /* bypass */
+ disable_val = 1;
+ clip_left = 0;
+ clip_right = 0;
+ } else {
+ disable_val = 0;
+ clip_left = x;
+ clip_right = fb_w - (x + in_w) - 1;
+ }
+
+ DRM_DEBUG_DRIVER("clip%d: clip_left=%d, clip_right=%d\n",
+ ch + 1, clip_left, clip_right);
+
+ writel(disable_val, base + ADE_CLIP_DISABLE(ch));
+ writel((fb_w - 1) << 16 | (in_h - 1), base + ADE_CLIP_SIZE0(ch));
+ writel(clip_left << 16 | clip_right, base + ADE_CLIP_SIZE1(ch));
+ ade_update_reload_bit(base, CLIP_OFST + ch, 0);
+}
+
+static void ade_clip_disable(void __iomem *base, u32 ch)
+{
+ writel(1, base + ADE_CLIP_DISABLE(ch));
+ ade_update_reload_bit(base, CLIP_OFST + ch, 1);
+}
+
+static bool has_Alpha_channel(int format)
+{
+ switch (format) {
+ case ADE_ARGB_8888:
+ case ADE_ABGR_8888:
+ case ADE_RGBA_8888:
+ case ADE_BGRA_8888:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static void ade_get_blending_params(u32 fmt, u8 glb_alpha, u8 *alp_mode,
+ u8 *alp_sel, u8 *under_alp_sel)
+{
+ bool has_alpha = has_Alpha_channel(fmt);
+
+ /*
+ * get alp_mode
+ */
+ if (has_alpha && glb_alpha < 255)
+ *alp_mode = ADE_ALP_PIXEL_AND_GLB;
+ else if (has_alpha)
+ *alp_mode = ADE_ALP_PIXEL;
+ else
+ *alp_mode = ADE_ALP_GLOBAL;
+
+ /*
+ * get alp sel
+ */
+ *alp_sel = ADE_ALP_MUL_COEFF_3; /* 1 */
+ *under_alp_sel = ADE_ALP_MUL_COEFF_2; /* 0 */
+}
+
+static void ade_compositor_routing_set(void __iomem *base, u8 ch,
+ u32 x0, u32 y0,
+ u32 in_w, u32 in_h, u32 fmt)
+{
+ u8 ovly_ch = 0; /* TODO: This is the zpos, only one plane now */
+ u8 glb_alpha = 255;
+ u32 x1 = x0 + in_w - 1;
+ u32 y1 = y0 + in_h - 1;
+ u32 val;
+ u8 alp_sel;
+ u8 under_alp_sel;
+ u8 alp_mode;
+
+ ade_get_blending_params(fmt, glb_alpha, &alp_mode, &alp_sel,
+ &under_alp_sel);
+
+ /* overlay routing setting
+ */
+ writel(x0 << 16 | y0, base + ADE_OVLY_CH_XY0(ovly_ch));
+ writel(x1 << 16 | y1, base + ADE_OVLY_CH_XY1(ovly_ch));
+ val = (ch + 1) << CH_SEL_OFST | BIT(CH_EN_OFST) |
+ alp_sel << CH_ALP_SEL_OFST |
+ under_alp_sel << CH_UNDER_ALP_SEL_OFST |
+ glb_alpha << CH_ALP_GBL_OFST |
+ alp_mode << CH_ALP_MODE_OFST;
+ writel(val, base + ADE_OVLY_CH_CTL(ovly_ch));
+ /* connect this plane/channel to overlay2 compositor */
+ ade_update_bits(base + ADE_OVLY_CTL, CH_OVLY_SEL_OFST(ovly_ch),
+ CH_OVLY_SEL_MASK, CH_OVLY_SEL_VAL(OUT_OVLY));
+}
+
+static void ade_compositor_routing_disable(void __iomem *base, u32 ch)
+{
+ u8 ovly_ch = 0; /* TODO: Only primary plane now */
+
+ /* disable this plane/channel */
+ ade_update_bits(base + ADE_OVLY_CH_CTL(ovly_ch), CH_EN_OFST,
+ MASK(1), 0);
+ /* dis-connect this plane/channel of overlay2 compositor */
+ ade_update_bits(base + ADE_OVLY_CTL, CH_OVLY_SEL_OFST(ovly_ch),
+ CH_OVLY_SEL_MASK, 0);
+}
+
+/*
+ * Typicaly, a channel looks like: DMA-->clip-->scale-->ctrans-->compositor
+ */
+static void ade_update_channel(struct ade_plane *aplane,
+ struct drm_framebuffer *fb, int crtc_x,
+ int crtc_y, unsigned int crtc_w,
+ unsigned int crtc_h, u32 src_x,
+ u32 src_y, u32 src_w, u32 src_h)
+{
+ struct ade_hw_ctx *ctx = aplane->ctx;
+ void __iomem *base = ctx->base;
+ u32 fmt = ade_get_format(fb->pixel_format);
+ u32 ch = aplane->ch;
+ u32 in_w;
+ u32 in_h;
+
+ DRM_DEBUG_DRIVER("channel%d: src:(%d, %d)-%dx%d, crtc:(%d, %d)-%dx%d",
+ ch + 1, src_x, src_y, src_w, src_h,
+ crtc_x, crtc_y, crtc_w, crtc_h);
+
+ /* 1) DMA setting */
+ in_w = src_w;
+ in_h = src_h;
+ ade_rdma_set(base, fb, ch, src_y, in_h, fmt);
+
+ /* 2) clip setting */
+ ade_clip_set(base, ch, fb->width, src_x, in_w, in_h);
+
+ /* 3) TODO: scale setting for overlay planes */
+
+ /* 4) TODO: ctran/csc setting for overlay planes */
+
+ /* 5) compositor routing setting */
+ ade_compositor_routing_set(base, ch, crtc_x, crtc_y, in_w, in_h, fmt);
+}
+
+static void ade_disable_channel(struct ade_plane *aplane)
+{
+ struct ade_hw_ctx *ctx = aplane->ctx;
+ void __iomem *base = ctx->base;
+ u32 ch = aplane->ch;
+
+ DRM_DEBUG_DRIVER("disable channel%d\n", ch + 1);
+
+ /* disable read DMA */
+ ade_rdma_disable(base, ch);
+
+ /* disable clip */
+ ade_clip_disable(base, ch);
+
+ /* disable compositor routing */
+ ade_compositor_routing_disable(base, ch);
+}
+
+static int ade_plane_prepare_fb(struct drm_plane *plane,
+ const struct drm_plane_state *new_state)
+{
+ /* do nothing */
+ return 0;
+}
+
+static void ade_plane_cleanup_fb(struct drm_plane *plane,
+ const struct drm_plane_state *old_state)
+{
+ /* do nothing */
+}
+
+static int ade_plane_atomic_check(struct drm_plane *plane,
+ struct drm_plane_state *state)
+{
+ struct drm_framebuffer *fb = state->fb;
+ struct drm_crtc *crtc = state->crtc;
+ struct drm_crtc_state *crtc_state;
+ u32 src_x = state->src_x >> 16;
+ u32 src_y = state->src_y >> 16;
+ u32 src_w = state->src_w >> 16;
+ u32 src_h = state->src_h >> 16;
+ int crtc_x = state->crtc_x;
+ int crtc_y = state->crtc_y;
+ u32 crtc_w = state->crtc_w;
+ u32 crtc_h = state->crtc_h;
+ u32 fmt;
+
+ if (!crtc || !fb)
+ return 0;
+
+ fmt = ade_get_format(fb->pixel_format);
+ if (fmt == ADE_FORMAT_UNSUPPORT)
+ return -EINVAL;
+
+ crtc_state = drm_atomic_get_crtc_state(state->state, crtc);
+ if (IS_ERR(crtc_state))
+ return PTR_ERR(crtc_state);
+
+ if (src_w != crtc_w || src_h != crtc_h) {
+ DRM_ERROR("Scale not support!!!\n");
+ return -EINVAL;
+ }
+
+ if (src_x + src_w > fb->width ||
+ src_y + src_h > fb->height)
+ return -EINVAL;
+
+ if (crtc_x < 0 || crtc_y < 0)
+ return -EINVAL;
+
+ if (crtc_x + crtc_w > crtc_state->adjusted_mode.hdisplay ||
+ crtc_y + crtc_h > crtc_state->adjusted_mode.vdisplay)
+ return -EINVAL;
+
+ return 0;
+}
+
+static void ade_plane_atomic_update(struct drm_plane *plane,
+ struct drm_plane_state *old_state)
+{
+ struct drm_plane_state *state = plane->state;
+ struct ade_plane *aplane = to_ade_plane(plane);
+
+ ade_update_channel(aplane, state->fb, state->crtc_x, state->crtc_y,
+ state->crtc_w, state->crtc_h,
+ state->src_x >> 16, state->src_y >> 16,
+ state->src_w >> 16, state->src_h >> 16);
+}
+
+static void ade_plane_atomic_disable(struct drm_plane *plane,
+ struct drm_plane_state *old_state)
+{
+ struct ade_plane *aplane = to_ade_plane(plane);
+
+ ade_disable_channel(aplane);
+}
+
+static const struct drm_plane_helper_funcs ade_plane_helper_funcs = {
+ .prepare_fb = ade_plane_prepare_fb,
+ .cleanup_fb = ade_plane_cleanup_fb,
+ .atomic_check = ade_plane_atomic_check,
+ .atomic_update = ade_plane_atomic_update,
+ .atomic_disable = ade_plane_atomic_disable,
+};
+
+static struct drm_plane_funcs ade_plane_funcs = {
+ .update_plane = drm_atomic_helper_update_plane,
+ .disable_plane = drm_atomic_helper_disable_plane,
+ .set_property = drm_atomic_helper_plane_set_property,
+ .destroy = drm_plane_cleanup,
+ .reset = drm_atomic_helper_plane_reset,
+ .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
+};
+
+static int ade_plane_init(struct drm_device *dev, struct ade_plane *aplane,
+ enum drm_plane_type type)
+{
+ const u32 *fmts;
+ u32 fmts_cnt;
+ int ret = 0;
+
+ /* get properties */
+ fmts_cnt = ade_get_channel_formats(aplane->ch, &fmts);
+ if (ret)
+ return ret;
+
+ ret = drm_universal_plane_init(dev, &aplane->base, 1, &ade_plane_funcs,
+ fmts, fmts_cnt, type, NULL);
+ if (ret) {
+ DRM_ERROR("fail to init plane, ch=%d\n", aplane->ch);
+ return ret;
+ }
+
+ drm_plane_helper_add(&aplane->base, &ade_plane_helper_funcs);
+
+ return 0;
+}
+
static int ade_dts_parse(struct platform_device *pdev, struct ade_hw_ctx *ctx)
{
struct resource *res;
@@ -426,7 +934,10 @@ static int ade_drm_init(struct drm_device *dev)
struct ade_data *ade;
struct ade_hw_ctx *ctx;
struct ade_crtc *acrtc;
+ struct ade_plane *aplane;
+ enum drm_plane_type type;
int ret;
+ int i;
ade = devm_kzalloc(dev->dev, sizeof(*ade), GFP_KERNEL);
if (!ade) {
@@ -444,6 +955,28 @@ static int ade_drm_init(struct drm_device *dev)
if (ret)
return ret;
+ /*
+ * plane init
+ * TODO: Now only support primary plane, overlay planes
+ * need to do.
+ */
+ for (i = 0; i < ADE_CH_NUM; i++) {
+ aplane = &ade->aplane[i];
+ aplane->ch = i;
+ aplane->ctx = ctx;
+ type = i == PRIMARY_CH ? DRM_PLANE_TYPE_PRIMARY :
+ DRM_PLANE_TYPE_OVERLAY;
+
+ ret = ade_plane_init(dev, aplane, type);
+ if (ret)
+ return ret;
+ }
+
+ /* crtc init */
+ ret = ade_crtc_init(dev, &acrtc->base, &ade->aplane[PRIMARY_CH].base);
+ if (ret)
+ return ret;
+
return 0;
}
--
2.8.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 04/10] drm/hisilicon: Add plane driver for ADE
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add plane funcs and helper funcs for ADE.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3:
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 535 +++++++++++++++++++++++-
1 file changed, 534 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
index cfbea957297b..8a7cb5e04bf4 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
@@ -27,13 +27,23 @@
#include <drm/drm_crtc_helper.h>
#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
+#include <drm/drm_plane_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_cma_helper.h>
#include "kirin_drm_drv.h"
#include "kirin_ade_reg.h"
+#define PRIMARY_CH ADE_CH1 /* primary plane */
+#define OUT_OVLY ADE_OVLY2 /* output overlay compositor */
+#define ADE_DEBUG 1
+
#define to_ade_crtc(crtc) \
container_of(crtc, struct ade_crtc, base)
+#define to_ade_plane(plane) \
+ container_of(plane, struct ade_plane, base)
+
struct ade_hw_ctx {
void __iomem *base;
struct regmap *noc_regmap;
@@ -52,11 +62,76 @@ struct ade_crtc {
u32 out_format;
};
+struct ade_plane {
+ struct drm_plane base;
+ void *ctx;
+ u8 ch; /* channel */
+};
+
struct ade_data {
struct ade_crtc acrtc;
+ struct ade_plane aplane[ADE_CH_NUM];
struct ade_hw_ctx ctx;
};
+/* ade-format info: */
+struct ade_format {
+ u32 pixel_format;
+ enum ade_fb_format ade_format;
+};
+
+static const struct ade_format ade_formats[] = {
+ /* 16bpp RGB: */
+ { DRM_FORMAT_RGB565, ADE_RGB_565 },
+ { DRM_FORMAT_BGR565, ADE_BGR_565 },
+ /* 24bpp RGB: */
+ { DRM_FORMAT_RGB888, ADE_RGB_888 },
+ { DRM_FORMAT_BGR888, ADE_BGR_888 },
+ /* 32bpp [A]RGB: */
+ { DRM_FORMAT_XRGB8888, ADE_XRGB_8888 },
+ { DRM_FORMAT_XBGR8888, ADE_XBGR_8888 },
+ { DRM_FORMAT_RGBA8888, ADE_RGBA_8888 },
+ { DRM_FORMAT_BGRA8888, ADE_BGRA_8888 },
+ { DRM_FORMAT_ARGB8888, ADE_ARGB_8888 },
+ { DRM_FORMAT_ABGR8888, ADE_ABGR_8888 },
+};
+
+static const u32 channel_formats1[] = {
+ /* channel 1,2,3,4 */
+ DRM_FORMAT_RGB565, DRM_FORMAT_BGR565, DRM_FORMAT_RGB888,
+ DRM_FORMAT_BGR888, DRM_FORMAT_XRGB8888, DRM_FORMAT_XBGR8888,
+ DRM_FORMAT_RGBA8888, DRM_FORMAT_BGRA8888, DRM_FORMAT_ARGB8888,
+ DRM_FORMAT_ABGR8888
+};
+
+u32 ade_get_channel_formats(u8 ch, const u32 **formats)
+{
+ switch (ch) {
+ case ADE_CH1:
+ *formats = channel_formats1;
+ return ARRAY_SIZE(channel_formats1);
+ default:
+ DRM_ERROR("no this channel %d\n", ch);
+ *formats = NULL;
+ return 0;
+ }
+}
+
+/* convert from fourcc format to ade format */
+static u32 ade_get_format(u32 pixel_format)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ade_formats); i++)
+ if (ade_formats[i].pixel_format == pixel_format)
+ return ade_formats[i].ade_format;
+
+ /* not found */
+ DRM_ERROR("Not found pixel format!!fourcc_format= %d\n",
+ pixel_format);
+ return ADE_FORMAT_UNSUPPORT;
+}
+
static void ade_update_reload_bit(void __iomem *base, u32 bit_num, u32 val)
{
u32 bit_ofst, reg_num;
@@ -89,7 +164,7 @@ static void ade_init(struct ade_hw_ctx *ctx)
/* clear overlay */
writel(0, base + ADE_OVLY1_TRANS_CFG);
writel(0, base + ADE_OVLY_CTL);
- writel(0, base + ADE_OVLYX_CTL(ADE_OVLY2));
+ writel(0, base + ADE_OVLYX_CTL(OUT_OVLY));
/* clear reset and reload regs */
writel(MASK(32), base + ADE_SOFT_RST_SEL(0));
writel(MASK(32), base + ADE_SOFT_RST_SEL(1));
@@ -155,6 +230,10 @@ static void ade_ldi_set_mode(struct ade_crtc *acrtc,
base + LDI_DSP_SIZE);
writel(plr_flags, base + LDI_PLR_CTRL);
+ /* set overlay compositor output size */
+ writel(((width - 1) << OUTPUT_XSIZE_OFST) | (height - 1),
+ base + ADE_OVLY_OUTPUT_SIZE(OUT_OVLY));
+
/* ctran6 setting */
writel(CTRAN_BYPASS_ON, base + ADE_CTRAN_DIS(ADE_CTRAN6));
/* the configured value is actual value - 1 */
@@ -229,6 +308,10 @@ static void ade_display_enable(struct ade_crtc *acrtc)
void __iomem *base = ctx->base;
u32 out_fmt = acrtc->out_format;
+ /* enable output overlay compositor */
+ writel(ADE_ENABLE, base + ADE_OVLYX_CTL(OUT_OVLY));
+ ade_update_reload_bit(base, OVLY_OFST + OUT_OVLY, 0);
+
/* display source setting */
writel(DISP_SRC_OVLY2, base + ADE_DISP_SRC_CFG);
@@ -242,6 +325,97 @@ static void ade_display_enable(struct ade_crtc *acrtc)
writel(DSI_PCLK_ON, base + LDI_HDMI_DSI_GT);
}
+#if ADE_DEBUG
+static void ade_rdma_dump_regs(void __iomem *base, u32 ch)
+{
+ u32 reg_ctrl, reg_addr, reg_size, reg_stride, reg_space, reg_en;
+ u32 val;
+
+ reg_ctrl = RD_CH_CTRL(ch);
+ reg_addr = RD_CH_ADDR(ch);
+ reg_size = RD_CH_SIZE(ch);
+ reg_stride = RD_CH_STRIDE(ch);
+ reg_space = RD_CH_SPACE(ch);
+ reg_en = RD_CH_EN(ch);
+
+ val = ade_read_reload_bit(base, RDMA_OFST + ch);
+ DRM_DEBUG_DRIVER("[rdma%d]: reload(%d)\n", ch + 1, val);
+ val = readl(base + reg_ctrl);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_ctrl(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_addr);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_addr(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_size);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_size(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_stride);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_stride(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_space);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_space(0x%08x)\n", ch + 1, val);
+ val = readl(base + reg_en);
+ DRM_DEBUG_DRIVER("[rdma%d]: reg_en(0x%08x)\n", ch + 1, val);
+}
+
+static void ade_clip_dump_regs(void __iomem *base, u32 ch)
+{
+ u32 val;
+
+ val = ade_read_reload_bit(base, CLIP_OFST + ch);
+ DRM_DEBUG_DRIVER("[clip%d]: reload(%d)\n", ch + 1, val);
+ val = readl(base + ADE_CLIP_DISABLE(ch));
+ DRM_DEBUG_DRIVER("[clip%d]: reg_clip_disable(0x%08x)\n", ch + 1, val);
+ val = readl(base + ADE_CLIP_SIZE0(ch));
+ DRM_DEBUG_DRIVER("[clip%d]: reg_clip_size0(0x%08x)\n", ch + 1, val);
+ val = readl(base + ADE_CLIP_SIZE1(ch));
+ DRM_DEBUG_DRIVER("[clip%d]: reg_clip_size1(0x%08x)\n", ch + 1, val);
+}
+
+static void ade_compositor_routing_dump_regs(void __iomem *base, u32 ch)
+{
+ u8 ovly_ch = 0; /* TODO: Only primary plane now */
+ u32 val;
+
+ val = readl(base + ADE_OVLY_CH_XY0(ovly_ch));
+ DRM_DEBUG_DRIVER("[overlay ch%d]: reg_ch_xy0(0x%08x)\n", ovly_ch, val);
+ val = readl(base + ADE_OVLY_CH_XY1(ovly_ch));
+ DRM_DEBUG_DRIVER("[overlay ch%d]: reg_ch_xy1(0x%08x)\n", ovly_ch, val);
+ val = readl(base + ADE_OVLY_CH_CTL(ovly_ch));
+ DRM_DEBUG_DRIVER("[overlay ch%d]: reg_ch_ctl(0x%08x)\n", ovly_ch, val);
+}
+
+static void ade_dump_overlay_compositor_regs(void __iomem *base, u32 comp)
+{
+ u32 val;
+
+ val = ade_read_reload_bit(base, OVLY_OFST + comp);
+ DRM_DEBUG_DRIVER("[overlay%d]: reload(%d)\n", comp + 1, val);
+ writel(ADE_ENABLE, base + ADE_OVLYX_CTL(comp));
+ DRM_DEBUG_DRIVER("[overlay%d]: reg_ctl(0x%08x)\n", comp + 1, val);
+ val = readl(base + ADE_OVLY_CTL);
+ DRM_DEBUG_DRIVER("ovly_ctl(0x%08x)\n", val);
+}
+
+static void ade_dump_regs(void __iomem *base)
+{
+ u32 i;
+
+ /* dump channel regs */
+ for (i = 0; i < ADE_CH_NUM; i++) {
+ /* dump rdma regs */
+ ade_rdma_dump_regs(base, i);
+
+ /* dump clip regs */
+ ade_clip_dump_regs(base, i);
+
+ /* dump compositor routing regs */
+ ade_compositor_routing_dump_regs(base, i);
+ }
+
+ /* dump overlay compositor regs */
+ ade_dump_overlay_compositor_regs(base, OUT_OVLY);
+}
+#else
+static void ade_dump_regs(void __iomem *base) { }
+#endif
+
static void ade_crtc_enable(struct drm_crtc *crtc)
{
struct ade_crtc *acrtc = to_ade_crtc(crtc);
@@ -259,6 +433,7 @@ static void ade_crtc_enable(struct drm_crtc *crtc)
ade_set_medianoc_qos(acrtc);
ade_display_enable(acrtc);
+ ade_dump_regs(ctx->base);
acrtc->enable = true;
}
@@ -313,6 +488,7 @@ static void ade_crtc_atomic_flush(struct drm_crtc *crtc,
/* only crtc is enabled regs take effect */
if (acrtc->enable) {
+ ade_dump_regs(base);
/* flush ade registers */
writel(ADE_ENABLE, base + ADE_EN);
}
@@ -369,6 +545,338 @@ static int ade_crtc_init(struct drm_device *dev, struct drm_crtc *crtc,
return 0;
}
+static void ade_rdma_set(void __iomem *base, struct drm_framebuffer *fb,
+ u32 ch, u32 y, u32 in_h, u32 fmt)
+{
+ struct drm_gem_cma_object *obj = drm_fb_cma_get_gem_obj(fb, 0);
+ u32 reg_ctrl, reg_addr, reg_size, reg_stride, reg_space, reg_en;
+ u32 stride = fb->pitches[0];
+ u32 addr = (u32)obj->paddr + y * stride;
+
+ DRM_DEBUG_DRIVER("rdma%d: (y=%d, height=%d), stride=%d, paddr=0x%x\n",
+ ch + 1, y, in_h, stride, (u32)obj->paddr);
+ DRM_DEBUG_DRIVER("addr=0x%x, fb:%dx%d, pixel_format=%d(%s)\n",
+ addr, fb->width, fb->height, fmt,
+ drm_get_format_name(fb->pixel_format));
+
+ /* get reg offset */
+ reg_ctrl = RD_CH_CTRL(ch);
+ reg_addr = RD_CH_ADDR(ch);
+ reg_size = RD_CH_SIZE(ch);
+ reg_stride = RD_CH_STRIDE(ch);
+ reg_space = RD_CH_SPACE(ch);
+ reg_en = RD_CH_EN(ch);
+
+ /*
+ * TODO: set rotation
+ */
+ writel((fmt << 16) & 0x1f0000, base + reg_ctrl);
+ writel(addr, base + reg_addr);
+ writel((in_h << 16) | stride, base + reg_size);
+ writel(stride, base + reg_stride);
+ writel(in_h * stride, base + reg_space);
+ writel(ADE_ENABLE, base + reg_en);
+ ade_update_reload_bit(base, RDMA_OFST + ch, 0);
+}
+
+static void ade_rdma_disable(void __iomem *base, u32 ch)
+{
+ u32 reg_en;
+
+ /* get reg offset */
+ reg_en = RD_CH_EN(ch);
+ writel(0, base + reg_en);
+ ade_update_reload_bit(base, RDMA_OFST + ch, 1);
+}
+
+static void ade_clip_set(void __iomem *base, u32 ch, u32 fb_w, u32 x,
+ u32 in_w, u32 in_h)
+{
+ u32 disable_val;
+ u32 clip_left;
+ u32 clip_right;
+
+ /*
+ * clip width, no need to clip height
+ */
+ if (fb_w == in_w) { /* bypass */
+ disable_val = 1;
+ clip_left = 0;
+ clip_right = 0;
+ } else {
+ disable_val = 0;
+ clip_left = x;
+ clip_right = fb_w - (x + in_w) - 1;
+ }
+
+ DRM_DEBUG_DRIVER("clip%d: clip_left=%d, clip_right=%d\n",
+ ch + 1, clip_left, clip_right);
+
+ writel(disable_val, base + ADE_CLIP_DISABLE(ch));
+ writel((fb_w - 1) << 16 | (in_h - 1), base + ADE_CLIP_SIZE0(ch));
+ writel(clip_left << 16 | clip_right, base + ADE_CLIP_SIZE1(ch));
+ ade_update_reload_bit(base, CLIP_OFST + ch, 0);
+}
+
+static void ade_clip_disable(void __iomem *base, u32 ch)
+{
+ writel(1, base + ADE_CLIP_DISABLE(ch));
+ ade_update_reload_bit(base, CLIP_OFST + ch, 1);
+}
+
+static bool has_Alpha_channel(int format)
+{
+ switch (format) {
+ case ADE_ARGB_8888:
+ case ADE_ABGR_8888:
+ case ADE_RGBA_8888:
+ case ADE_BGRA_8888:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static void ade_get_blending_params(u32 fmt, u8 glb_alpha, u8 *alp_mode,
+ u8 *alp_sel, u8 *under_alp_sel)
+{
+ bool has_alpha = has_Alpha_channel(fmt);
+
+ /*
+ * get alp_mode
+ */
+ if (has_alpha && glb_alpha < 255)
+ *alp_mode = ADE_ALP_PIXEL_AND_GLB;
+ else if (has_alpha)
+ *alp_mode = ADE_ALP_PIXEL;
+ else
+ *alp_mode = ADE_ALP_GLOBAL;
+
+ /*
+ * get alp sel
+ */
+ *alp_sel = ADE_ALP_MUL_COEFF_3; /* 1 */
+ *under_alp_sel = ADE_ALP_MUL_COEFF_2; /* 0 */
+}
+
+static void ade_compositor_routing_set(void __iomem *base, u8 ch,
+ u32 x0, u32 y0,
+ u32 in_w, u32 in_h, u32 fmt)
+{
+ u8 ovly_ch = 0; /* TODO: This is the zpos, only one plane now */
+ u8 glb_alpha = 255;
+ u32 x1 = x0 + in_w - 1;
+ u32 y1 = y0 + in_h - 1;
+ u32 val;
+ u8 alp_sel;
+ u8 under_alp_sel;
+ u8 alp_mode;
+
+ ade_get_blending_params(fmt, glb_alpha, &alp_mode, &alp_sel,
+ &under_alp_sel);
+
+ /* overlay routing setting
+ */
+ writel(x0 << 16 | y0, base + ADE_OVLY_CH_XY0(ovly_ch));
+ writel(x1 << 16 | y1, base + ADE_OVLY_CH_XY1(ovly_ch));
+ val = (ch + 1) << CH_SEL_OFST | BIT(CH_EN_OFST) |
+ alp_sel << CH_ALP_SEL_OFST |
+ under_alp_sel << CH_UNDER_ALP_SEL_OFST |
+ glb_alpha << CH_ALP_GBL_OFST |
+ alp_mode << CH_ALP_MODE_OFST;
+ writel(val, base + ADE_OVLY_CH_CTL(ovly_ch));
+ /* connect this plane/channel to overlay2 compositor */
+ ade_update_bits(base + ADE_OVLY_CTL, CH_OVLY_SEL_OFST(ovly_ch),
+ CH_OVLY_SEL_MASK, CH_OVLY_SEL_VAL(OUT_OVLY));
+}
+
+static void ade_compositor_routing_disable(void __iomem *base, u32 ch)
+{
+ u8 ovly_ch = 0; /* TODO: Only primary plane now */
+
+ /* disable this plane/channel */
+ ade_update_bits(base + ADE_OVLY_CH_CTL(ovly_ch), CH_EN_OFST,
+ MASK(1), 0);
+ /* dis-connect this plane/channel of overlay2 compositor */
+ ade_update_bits(base + ADE_OVLY_CTL, CH_OVLY_SEL_OFST(ovly_ch),
+ CH_OVLY_SEL_MASK, 0);
+}
+
+/*
+ * Typicaly, a channel looks like: DMA-->clip-->scale-->ctrans-->compositor
+ */
+static void ade_update_channel(struct ade_plane *aplane,
+ struct drm_framebuffer *fb, int crtc_x,
+ int crtc_y, unsigned int crtc_w,
+ unsigned int crtc_h, u32 src_x,
+ u32 src_y, u32 src_w, u32 src_h)
+{
+ struct ade_hw_ctx *ctx = aplane->ctx;
+ void __iomem *base = ctx->base;
+ u32 fmt = ade_get_format(fb->pixel_format);
+ u32 ch = aplane->ch;
+ u32 in_w;
+ u32 in_h;
+
+ DRM_DEBUG_DRIVER("channel%d: src:(%d, %d)-%dx%d, crtc:(%d, %d)-%dx%d",
+ ch + 1, src_x, src_y, src_w, src_h,
+ crtc_x, crtc_y, crtc_w, crtc_h);
+
+ /* 1) DMA setting */
+ in_w = src_w;
+ in_h = src_h;
+ ade_rdma_set(base, fb, ch, src_y, in_h, fmt);
+
+ /* 2) clip setting */
+ ade_clip_set(base, ch, fb->width, src_x, in_w, in_h);
+
+ /* 3) TODO: scale setting for overlay planes */
+
+ /* 4) TODO: ctran/csc setting for overlay planes */
+
+ /* 5) compositor routing setting */
+ ade_compositor_routing_set(base, ch, crtc_x, crtc_y, in_w, in_h, fmt);
+}
+
+static void ade_disable_channel(struct ade_plane *aplane)
+{
+ struct ade_hw_ctx *ctx = aplane->ctx;
+ void __iomem *base = ctx->base;
+ u32 ch = aplane->ch;
+
+ DRM_DEBUG_DRIVER("disable channel%d\n", ch + 1);
+
+ /* disable read DMA */
+ ade_rdma_disable(base, ch);
+
+ /* disable clip */
+ ade_clip_disable(base, ch);
+
+ /* disable compositor routing */
+ ade_compositor_routing_disable(base, ch);
+}
+
+static int ade_plane_prepare_fb(struct drm_plane *plane,
+ const struct drm_plane_state *new_state)
+{
+ /* do nothing */
+ return 0;
+}
+
+static void ade_plane_cleanup_fb(struct drm_plane *plane,
+ const struct drm_plane_state *old_state)
+{
+ /* do nothing */
+}
+
+static int ade_plane_atomic_check(struct drm_plane *plane,
+ struct drm_plane_state *state)
+{
+ struct drm_framebuffer *fb = state->fb;
+ struct drm_crtc *crtc = state->crtc;
+ struct drm_crtc_state *crtc_state;
+ u32 src_x = state->src_x >> 16;
+ u32 src_y = state->src_y >> 16;
+ u32 src_w = state->src_w >> 16;
+ u32 src_h = state->src_h >> 16;
+ int crtc_x = state->crtc_x;
+ int crtc_y = state->crtc_y;
+ u32 crtc_w = state->crtc_w;
+ u32 crtc_h = state->crtc_h;
+ u32 fmt;
+
+ if (!crtc || !fb)
+ return 0;
+
+ fmt = ade_get_format(fb->pixel_format);
+ if (fmt == ADE_FORMAT_UNSUPPORT)
+ return -EINVAL;
+
+ crtc_state = drm_atomic_get_crtc_state(state->state, crtc);
+ if (IS_ERR(crtc_state))
+ return PTR_ERR(crtc_state);
+
+ if (src_w != crtc_w || src_h != crtc_h) {
+ DRM_ERROR("Scale not support!!!\n");
+ return -EINVAL;
+ }
+
+ if (src_x + src_w > fb->width ||
+ src_y + src_h > fb->height)
+ return -EINVAL;
+
+ if (crtc_x < 0 || crtc_y < 0)
+ return -EINVAL;
+
+ if (crtc_x + crtc_w > crtc_state->adjusted_mode.hdisplay ||
+ crtc_y + crtc_h > crtc_state->adjusted_mode.vdisplay)
+ return -EINVAL;
+
+ return 0;
+}
+
+static void ade_plane_atomic_update(struct drm_plane *plane,
+ struct drm_plane_state *old_state)
+{
+ struct drm_plane_state *state = plane->state;
+ struct ade_plane *aplane = to_ade_plane(plane);
+
+ ade_update_channel(aplane, state->fb, state->crtc_x, state->crtc_y,
+ state->crtc_w, state->crtc_h,
+ state->src_x >> 16, state->src_y >> 16,
+ state->src_w >> 16, state->src_h >> 16);
+}
+
+static void ade_plane_atomic_disable(struct drm_plane *plane,
+ struct drm_plane_state *old_state)
+{
+ struct ade_plane *aplane = to_ade_plane(plane);
+
+ ade_disable_channel(aplane);
+}
+
+static const struct drm_plane_helper_funcs ade_plane_helper_funcs = {
+ .prepare_fb = ade_plane_prepare_fb,
+ .cleanup_fb = ade_plane_cleanup_fb,
+ .atomic_check = ade_plane_atomic_check,
+ .atomic_update = ade_plane_atomic_update,
+ .atomic_disable = ade_plane_atomic_disable,
+};
+
+static struct drm_plane_funcs ade_plane_funcs = {
+ .update_plane = drm_atomic_helper_update_plane,
+ .disable_plane = drm_atomic_helper_disable_plane,
+ .set_property = drm_atomic_helper_plane_set_property,
+ .destroy = drm_plane_cleanup,
+ .reset = drm_atomic_helper_plane_reset,
+ .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
+};
+
+static int ade_plane_init(struct drm_device *dev, struct ade_plane *aplane,
+ enum drm_plane_type type)
+{
+ const u32 *fmts;
+ u32 fmts_cnt;
+ int ret = 0;
+
+ /* get properties */
+ fmts_cnt = ade_get_channel_formats(aplane->ch, &fmts);
+ if (ret)
+ return ret;
+
+ ret = drm_universal_plane_init(dev, &aplane->base, 1, &ade_plane_funcs,
+ fmts, fmts_cnt, type, NULL);
+ if (ret) {
+ DRM_ERROR("fail to init plane, ch=%d\n", aplane->ch);
+ return ret;
+ }
+
+ drm_plane_helper_add(&aplane->base, &ade_plane_helper_funcs);
+
+ return 0;
+}
+
static int ade_dts_parse(struct platform_device *pdev, struct ade_hw_ctx *ctx)
{
struct resource *res;
@@ -426,7 +934,10 @@ static int ade_drm_init(struct drm_device *dev)
struct ade_data *ade;
struct ade_hw_ctx *ctx;
struct ade_crtc *acrtc;
+ struct ade_plane *aplane;
+ enum drm_plane_type type;
int ret;
+ int i;
ade = devm_kzalloc(dev->dev, sizeof(*ade), GFP_KERNEL);
if (!ade) {
@@ -444,6 +955,28 @@ static int ade_drm_init(struct drm_device *dev)
if (ret)
return ret;
+ /*
+ * plane init
+ * TODO: Now only support primary plane, overlay planes
+ * need to do.
+ */
+ for (i = 0; i < ADE_CH_NUM; i++) {
+ aplane = &ade->aplane[i];
+ aplane->ch = i;
+ aplane->ctx = ctx;
+ type = i == PRIMARY_CH ? DRM_PLANE_TYPE_PRIMARY :
+ DRM_PLANE_TYPE_OVERLAY;
+
+ ret = ade_plane_init(dev, aplane, type);
+ if (ret)
+ return ret;
+ }
+
+ /* crtc init */
+ ret = ade_crtc_init(dev, &acrtc->base, &ade->aplane[PRIMARY_CH].base);
+ if (ret)
+ return ret;
+
return 0;
}
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 05/10] drm/hisilicon: Add vblank driver for ADE
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add vblank irq handle.
v8: None.
v7:
- Fix irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
v6: None.
v5: None.
v4: None.
v3:
- Remove hisi_get_crtc_from_index func.
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 62 +++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 14 +++++-
2 files changed, 75 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
index 8a7cb5e04bf4..fba6372d060e 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
@@ -302,6 +302,59 @@ static void ade_set_medianoc_qos(struct ade_crtc *acrtc)
SOCKET_QOS_EN, SOCKET_QOS_EN);
}
+static int ade_enable_vblank(struct drm_device *dev, unsigned int pipe)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+ struct ade_crtc *acrtc = to_ade_crtc(priv->crtc[pipe]);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+
+ if (!ctx->power_on)
+ (void)ade_power_up(ctx);
+
+ ade_update_bits(base + LDI_INT_EN, FRAME_END_INT_EN_OFST,
+ MASK(1), 1);
+
+ return 0;
+}
+
+static void ade_disable_vblank(struct drm_device *dev, unsigned int pipe)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+ struct ade_crtc *acrtc = to_ade_crtc(priv->crtc[pipe]);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+
+ if (!ctx->power_on) {
+ DRM_ERROR("power is down! vblank disable fail\n");
+ return;
+ }
+
+ ade_update_bits(base + LDI_INT_EN, FRAME_END_INT_EN_OFST,
+ MASK(1), 0);
+}
+
+static irqreturn_t ade_irq_handler(int irq, void *data)
+{
+ struct ade_crtc *acrtc = data;
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ struct drm_crtc *crtc = &acrtc->base;
+ void __iomem *base = ctx->base;
+ u32 status;
+
+ status = readl(base + LDI_MSK_INT);
+ DRM_DEBUG_VBL("LDI IRQ: status=0x%X\n", status);
+
+ /* vblank irq */
+ if (status & BIT(FRAME_END_INT_EN_OFST)) {
+ ade_update_bits(base + LDI_INT_CLR, FRAME_END_INT_EN_OFST,
+ MASK(1), 1);
+ drm_crtc_handle_vblank(crtc);
+ }
+
+ return IRQ_HANDLED;
+}
+
static void ade_display_enable(struct ade_crtc *acrtc)
{
struct ade_hw_ctx *ctx = acrtc->ctx;
@@ -977,6 +1030,15 @@ static int ade_drm_init(struct drm_device *dev)
if (ret)
return ret;
+ /* vblank irq init */
+ ret = devm_request_irq(dev->dev, ctx->irq, ade_irq_handler,
+ IRQF_SHARED, dev->driver->name, acrtc);
+ if (ret)
+ return ret;
+ dev->driver->get_vblank_counter = drm_vblank_no_hw_counter;
+ dev->driver->enable_vblank = ade_enable_vblank;
+ dev->driver->disable_vblank = ade_disable_vblank;
+
return 0;
}
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
index 578a1eb94517..2a899c5bb14e 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -32,6 +32,7 @@ static int kirin_drm_kms_cleanup(struct drm_device *dev)
{
struct kirin_drm_private *priv = dev->dev_private;
+ drm_vblank_cleanup(dev);
dc_ops->cleanup(dev);
drm_mode_config_cleanup(dev);
devm_kfree(dev->dev, priv);
@@ -85,11 +86,22 @@ static int kirin_drm_kms_init(struct drm_device *dev)
goto err_dc_cleanup;
}
+ /* vblank init */
+ ret = drm_vblank_init(dev, dev->mode_config.num_crtc);
+ if (ret) {
+ DRM_ERROR("failed to initialize vblank.\n");
+ goto err_unbind_all;
+ }
+ /* with irq_enabled = true, we can use the vblank feature. */
+ dev->irq_enabled = true;
+
/* reset all the states of crtc/plane/encoder/connector */
drm_mode_config_reset(dev);
return 0;
+err_unbind_all:
+ component_unbind_all(dev->dev, dev);
err_dc_cleanup:
dc_ops->cleanup(dev);
err_mode_config_cleanup:
@@ -123,7 +135,7 @@ static int kirin_gem_cma_dumb_create(struct drm_file *file,
static struct drm_driver kirin_drm_driver = {
.driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME |
- DRIVER_ATOMIC,
+ DRIVER_ATOMIC | DRIVER_HAVE_IRQ,
.fops = &kirin_drm_fops,
.set_busid = drm_platform_set_busid,
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 05/10] drm/hisilicon: Add vblank driver for ADE
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add vblank irq handle.
v8: None.
v7:
- Fix irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
v6: None.
v5: None.
v4: None.
v3:
- Remove hisi_get_crtc_from_index func.
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 62 +++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 14 +++++-
2 files changed, 75 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
index 8a7cb5e04bf4..fba6372d060e 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
@@ -302,6 +302,59 @@ static void ade_set_medianoc_qos(struct ade_crtc *acrtc)
SOCKET_QOS_EN, SOCKET_QOS_EN);
}
+static int ade_enable_vblank(struct drm_device *dev, unsigned int pipe)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+ struct ade_crtc *acrtc = to_ade_crtc(priv->crtc[pipe]);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+
+ if (!ctx->power_on)
+ (void)ade_power_up(ctx);
+
+ ade_update_bits(base + LDI_INT_EN, FRAME_END_INT_EN_OFST,
+ MASK(1), 1);
+
+ return 0;
+}
+
+static void ade_disable_vblank(struct drm_device *dev, unsigned int pipe)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+ struct ade_crtc *acrtc = to_ade_crtc(priv->crtc[pipe]);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ void __iomem *base = ctx->base;
+
+ if (!ctx->power_on) {
+ DRM_ERROR("power is down! vblank disable fail\n");
+ return;
+ }
+
+ ade_update_bits(base + LDI_INT_EN, FRAME_END_INT_EN_OFST,
+ MASK(1), 0);
+}
+
+static irqreturn_t ade_irq_handler(int irq, void *data)
+{
+ struct ade_crtc *acrtc = data;
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+ struct drm_crtc *crtc = &acrtc->base;
+ void __iomem *base = ctx->base;
+ u32 status;
+
+ status = readl(base + LDI_MSK_INT);
+ DRM_DEBUG_VBL("LDI IRQ: status=0x%X\n", status);
+
+ /* vblank irq */
+ if (status & BIT(FRAME_END_INT_EN_OFST)) {
+ ade_update_bits(base + LDI_INT_CLR, FRAME_END_INT_EN_OFST,
+ MASK(1), 1);
+ drm_crtc_handle_vblank(crtc);
+ }
+
+ return IRQ_HANDLED;
+}
+
static void ade_display_enable(struct ade_crtc *acrtc)
{
struct ade_hw_ctx *ctx = acrtc->ctx;
@@ -977,6 +1030,15 @@ static int ade_drm_init(struct drm_device *dev)
if (ret)
return ret;
+ /* vblank irq init */
+ ret = devm_request_irq(dev->dev, ctx->irq, ade_irq_handler,
+ IRQF_SHARED, dev->driver->name, acrtc);
+ if (ret)
+ return ret;
+ dev->driver->get_vblank_counter = drm_vblank_no_hw_counter;
+ dev->driver->enable_vblank = ade_enable_vblank;
+ dev->driver->disable_vblank = ade_disable_vblank;
+
return 0;
}
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
index 578a1eb94517..2a899c5bb14e 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -32,6 +32,7 @@ static int kirin_drm_kms_cleanup(struct drm_device *dev)
{
struct kirin_drm_private *priv = dev->dev_private;
+ drm_vblank_cleanup(dev);
dc_ops->cleanup(dev);
drm_mode_config_cleanup(dev);
devm_kfree(dev->dev, priv);
@@ -85,11 +86,22 @@ static int kirin_drm_kms_init(struct drm_device *dev)
goto err_dc_cleanup;
}
+ /* vblank init */
+ ret = drm_vblank_init(dev, dev->mode_config.num_crtc);
+ if (ret) {
+ DRM_ERROR("failed to initialize vblank.\n");
+ goto err_unbind_all;
+ }
+ /* with irq_enabled = true, we can use the vblank feature. */
+ dev->irq_enabled = true;
+
/* reset all the states of crtc/plane/encoder/connector */
drm_mode_config_reset(dev);
return 0;
+err_unbind_all:
+ component_unbind_all(dev->dev, dev);
err_dc_cleanup:
dc_ops->cleanup(dev);
err_mode_config_cleanup:
@@ -123,7 +135,7 @@ static int kirin_gem_cma_dumb_create(struct drm_file *file,
static struct drm_driver kirin_drm_driver = {
.driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME |
- DRIVER_ATOMIC,
+ DRIVER_ATOMIC | DRIVER_HAVE_IRQ,
.fops = &kirin_drm_fops,
.set_busid = drm_platform_set_busid,
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 06/10] drm/hisilicon: Add cma fbdev and hotplug
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add cma Fbdev, Fbdev is legency and optional, you can enable/disable it by
configuring DRM_FBDEV_EMULATION.
Add hotplug.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3: None.
v2:
- Use CONFIG_DRM_FBDEV_EMULATION instead of CONFIG_DRM_HISI_FBDEV.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 34 +++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 3 +++
2 files changed, 37 insertions(+)
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
index 2a899c5bb14e..e102c9e1e7b2 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -23,6 +23,7 @@
#include <drm/drm_gem_cma_helper.h>
#include <drm/drm_fb_cma_helper.h>
#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
#include "kirin_drm_drv.h"
@@ -32,6 +33,13 @@ static int kirin_drm_kms_cleanup(struct drm_device *dev)
{
struct kirin_drm_private *priv = dev->dev_private;
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+ if (priv->fbdev) {
+ drm_fbdev_cma_fini(priv->fbdev);
+ priv->fbdev = NULL;
+ }
+#endif
+ drm_kms_helper_poll_fini(dev);
drm_vblank_cleanup(dev);
dc_ops->cleanup(dev);
drm_mode_config_cleanup(dev);
@@ -41,8 +49,28 @@ static int kirin_drm_kms_cleanup(struct drm_device *dev)
return 0;
}
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+static void kirin_fbdev_output_poll_changed(struct drm_device *dev)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+
+ if (priv->fbdev) {
+ drm_fbdev_cma_hotplug_event(priv->fbdev);
+ } else {
+ priv->fbdev = drm_fbdev_cma_init(dev, 32,
+ dev->mode_config.num_crtc,
+ dev->mode_config.num_connector);
+ if (IS_ERR(priv->fbdev))
+ priv->fbdev = NULL;
+ }
+}
+#endif
+
static const struct drm_mode_config_funcs kirin_drm_mode_config_funcs = {
.fb_create = drm_fb_cma_create,
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+ .output_poll_changed = kirin_fbdev_output_poll_changed,
+#endif
.atomic_check = drm_atomic_helper_check,
.atomic_commit = drm_atomic_helper_commit,
};
@@ -98,6 +126,12 @@ static int kirin_drm_kms_init(struct drm_device *dev)
/* reset all the states of crtc/plane/encoder/connector */
drm_mode_config_reset(dev);
+ /* init kms poll for handling hpd */
+ drm_kms_helper_poll_init(dev);
+
+ /* force detection after connectors init */
+ (void)drm_helper_hpd_irq_event(dev);
+
return 0;
err_unbind_all:
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
index 5a05ad6a81db..1a07caf8e7f4 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
@@ -21,6 +21,9 @@ struct kirin_dc_ops {
struct kirin_drm_private {
struct drm_crtc *crtc[MAX_CRTC];
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+ struct drm_fbdev_cma *fbdev;
+#endif
};
extern const struct kirin_dc_ops ade_dc_ops;
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 06/10] drm/hisilicon: Add cma fbdev and hotplug
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add cma Fbdev, Fbdev is legency and optional, you can enable/disable it by
configuring DRM_FBDEV_EMULATION.
Add hotplug.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3: None.
v2:
- Use CONFIG_DRM_FBDEV_EMULATION instead of CONFIG_DRM_HISI_FBDEV.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 34 +++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 3 +++
2 files changed, 37 insertions(+)
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
index 2a899c5bb14e..e102c9e1e7b2 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
@@ -23,6 +23,7 @@
#include <drm/drm_gem_cma_helper.h>
#include <drm/drm_fb_cma_helper.h>
#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
#include "kirin_drm_drv.h"
@@ -32,6 +33,13 @@ static int kirin_drm_kms_cleanup(struct drm_device *dev)
{
struct kirin_drm_private *priv = dev->dev_private;
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+ if (priv->fbdev) {
+ drm_fbdev_cma_fini(priv->fbdev);
+ priv->fbdev = NULL;
+ }
+#endif
+ drm_kms_helper_poll_fini(dev);
drm_vblank_cleanup(dev);
dc_ops->cleanup(dev);
drm_mode_config_cleanup(dev);
@@ -41,8 +49,28 @@ static int kirin_drm_kms_cleanup(struct drm_device *dev)
return 0;
}
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+static void kirin_fbdev_output_poll_changed(struct drm_device *dev)
+{
+ struct kirin_drm_private *priv = dev->dev_private;
+
+ if (priv->fbdev) {
+ drm_fbdev_cma_hotplug_event(priv->fbdev);
+ } else {
+ priv->fbdev = drm_fbdev_cma_init(dev, 32,
+ dev->mode_config.num_crtc,
+ dev->mode_config.num_connector);
+ if (IS_ERR(priv->fbdev))
+ priv->fbdev = NULL;
+ }
+}
+#endif
+
static const struct drm_mode_config_funcs kirin_drm_mode_config_funcs = {
.fb_create = drm_fb_cma_create,
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+ .output_poll_changed = kirin_fbdev_output_poll_changed,
+#endif
.atomic_check = drm_atomic_helper_check,
.atomic_commit = drm_atomic_helper_commit,
};
@@ -98,6 +126,12 @@ static int kirin_drm_kms_init(struct drm_device *dev)
/* reset all the states of crtc/plane/encoder/connector */
drm_mode_config_reset(dev);
+ /* init kms poll for handling hpd */
+ drm_kms_helper_poll_init(dev);
+
+ /* force detection after connectors init */
+ (void)drm_helper_hpd_irq_event(dev);
+
return 0;
err_unbind_all:
diff --git a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
index 5a05ad6a81db..1a07caf8e7f4 100644
--- a/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
+++ b/drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
@@ -21,6 +21,9 @@ struct kirin_dc_ops {
struct kirin_drm_private {
struct drm_crtc *crtc[MAX_CRTC];
+#ifdef CONFIG_DRM_FBDEV_EMULATION
+ struct drm_fbdev_cma *fbdev;
+#endif
};
extern const struct kirin_dc_ops ade_dc_ops;
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 07/10] drm/hisilicon: Add designware dsi encoder driver
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add DesignWare MIPI DSI Host Controller v1.02 encoder driver
for hi6220 SoC.
v8: None.
v7:
- A few regs define clean up.
v6:
- Change "pclk_dsi" to "pclk".
v5: None.
v4: None.
v3:
- Rename file name to dw_drm_dsi.c
- Make encoder type as DRM_MODE_ENCODER_DSI.
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Andy Green <andy.green@linaro.org>
---
drivers/gpu/drm/hisilicon/kirin/Kconfig | 1 +
drivers/gpu/drm/hisilicon/kirin/Makefile | 3 +-
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 755 +++++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++++
4 files changed, 861 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
diff --git a/drivers/gpu/drm/hisilicon/kirin/Kconfig b/drivers/gpu/drm/hisilicon/kirin/Kconfig
index 3ac4b8edeac1..de0d454c5c13 100644
--- a/drivers/gpu/drm/hisilicon/kirin/Kconfig
+++ b/drivers/gpu/drm/hisilicon/kirin/Kconfig
@@ -4,6 +4,7 @@ config DRM_HISI_KIRIN
select DRM_KMS_HELPER
select DRM_GEM_CMA_HELPER
select DRM_KMS_CMA_HELPER
+ select DRM_MIPI_DSI
help
Choose this option if you have a hisilicon Kirin chipsets(hi6220).
If M is selected the module will be called kirin-drm.
diff --git a/drivers/gpu/drm/hisilicon/kirin/Makefile b/drivers/gpu/drm/hisilicon/kirin/Makefile
index 2a61ab006ddb..5dcd0d4328b6 100644
--- a/drivers/gpu/drm/hisilicon/kirin/Makefile
+++ b/drivers/gpu/drm/hisilicon/kirin/Makefile
@@ -1,4 +1,5 @@
kirin-drm-y := kirin_drm_drv.o \
- kirin_drm_ade.o
+ kirin_drm_ade.o \
+ dw_drm_dsi.o
obj-$(CONFIG_DRM_HISI_KIRIN) += kirin-drm.o
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
new file mode 100644
index 000000000000..1a930b77ec53
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
@@ -0,0 +1,755 @@
+/*
+ * DesignWare MIPI DSI Host Controller v1.02 driver
+ *
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * Author:
+ * Xinliang Liu <z.liuxinliang@hisilicon.com>
+ * Xinliang Liu <xinliang.liu@linaro.org>
+ * Xinwei Kong <kong.kongxinwei@hisilicon.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/of_graph.h>
+
+#include <drm/drm_of.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_encoder_slave.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "dw_dsi_reg.h"
+
+#define MAX_TX_ESC_CLK 10
+#define ROUND(x, y) ((x) / (y) + \
+ ((x) % (y) * 10 / (y) >= 5 ? 1 : 0))
+#define PHY_REF_CLK_RATE 19200000
+#define PHY_REF_CLK_PERIOD_PS (1000000000 / (PHY_REF_CLK_RATE / 1000))
+
+#define encoder_to_dsi(encoder) \
+ container_of(encoder, struct dw_dsi, encoder)
+#define host_to_dsi(host) \
+ container_of(host, struct dw_dsi, host)
+
+struct mipi_phy_params {
+ u32 clk_t_lpx;
+ u32 clk_t_hs_prepare;
+ u32 clk_t_hs_zero;
+ u32 clk_t_hs_trial;
+ u32 clk_t_wakeup;
+ u32 data_t_lpx;
+ u32 data_t_hs_prepare;
+ u32 data_t_hs_zero;
+ u32 data_t_hs_trial;
+ u32 data_t_ta_go;
+ u32 data_t_ta_get;
+ u32 data_t_wakeup;
+ u32 hstx_ckg_sel;
+ u32 pll_fbd_div5f;
+ u32 pll_fbd_div1f;
+ u32 pll_fbd_2p;
+ u32 pll_enbwt;
+ u32 pll_fbd_p;
+ u32 pll_fbd_s;
+ u32 pll_pre_div1p;
+ u32 pll_pre_p;
+ u32 pll_vco_750M;
+ u32 pll_lpf_rs;
+ u32 pll_lpf_cs;
+ u32 clklp2hs_time;
+ u32 clkhs2lp_time;
+ u32 lp2hs_time;
+ u32 hs2lp_time;
+ u32 clk_to_data_delay;
+ u32 data_to_clk_delay;
+ u32 lane_byte_clk_kHz;
+ u32 clk_division;
+};
+
+struct dsi_hw_ctx {
+ void __iomem *base;
+ struct clk *pclk;
+};
+
+struct dw_dsi {
+ struct drm_encoder encoder;
+ struct drm_display_mode cur_mode;
+ struct dsi_hw_ctx *ctx;
+ struct mipi_phy_params phy;
+
+ u32 lanes;
+ enum mipi_dsi_pixel_format format;
+ unsigned long mode_flags;
+ bool enable;
+};
+
+struct dsi_data {
+ struct dw_dsi dsi;
+ struct dsi_hw_ctx ctx;
+};
+
+struct dsi_phy_range {
+ u32 min_range_kHz;
+ u32 max_range_kHz;
+ u32 pll_vco_750M;
+ u32 hstx_ckg_sel;
+};
+
+static const struct dsi_phy_range dphy_range_info[] = {
+ { 46875, 62500, 1, 7 },
+ { 62500, 93750, 0, 7 },
+ { 93750, 125000, 1, 6 },
+ { 125000, 187500, 0, 6 },
+ { 187500, 250000, 1, 5 },
+ { 250000, 375000, 0, 5 },
+ { 375000, 500000, 1, 4 },
+ { 500000, 750000, 0, 4 },
+ { 750000, 1000000, 1, 0 },
+ { 1000000, 1500000, 0, 0 }
+};
+
+static u32 dsi_calc_phy_rate(u32 req_kHz, struct mipi_phy_params *phy)
+{
+ u32 ref_clk_ps = PHY_REF_CLK_PERIOD_PS;
+ u32 tmp_kHz = req_kHz;
+ u32 i = 0;
+ u32 q_pll = 1;
+ u32 m_pll = 0;
+ u32 n_pll = 0;
+ u32 r_pll = 1;
+ u32 m_n = 0;
+ u32 m_n_int = 0;
+ u32 f_kHz = 0;
+ u64 temp;
+
+ /*
+ * Find a rate >= req_kHz.
+ */
+ do {
+ f_kHz = tmp_kHz;
+
+ for (i = 0; i < ARRAY_SIZE(dphy_range_info); i++)
+ if (f_kHz >= dphy_range_info[i].min_range_kHz &&
+ f_kHz <= dphy_range_info[i].max_range_kHz)
+ break;
+
+ if (i == ARRAY_SIZE(dphy_range_info)) {
+ DRM_ERROR("%dkHz out of range\n", f_kHz);
+ return 0;
+ }
+
+ phy->pll_vco_750M = dphy_range_info[i].pll_vco_750M;
+ phy->hstx_ckg_sel = dphy_range_info[i].hstx_ckg_sel;
+
+ if (phy->hstx_ckg_sel <= 7 &&
+ phy->hstx_ckg_sel >= 4)
+ q_pll = 0x10 >> (7 - phy->hstx_ckg_sel);
+
+ temp = f_kHz * (u64)q_pll * (u64)ref_clk_ps;
+ m_n_int = temp / (u64)1000000000;
+ m_n = (temp % (u64)1000000000) / (u64)100000000;
+
+ if (m_n_int % 2 == 0) {
+ if (m_n * 6 >= 50) {
+ n_pll = 2;
+ m_pll = (m_n_int + 1) * n_pll;
+ } else if (m_n * 6 >= 30) {
+ n_pll = 3;
+ m_pll = m_n_int * n_pll + 2;
+ } else {
+ n_pll = 1;
+ m_pll = m_n_int * n_pll;
+ }
+ } else {
+ if (m_n * 6 >= 50) {
+ n_pll = 1;
+ m_pll = (m_n_int + 1) * n_pll;
+ } else if (m_n * 6 >= 30) {
+ n_pll = 1;
+ m_pll = (m_n_int + 1) * n_pll;
+ } else if (m_n * 6 >= 10) {
+ n_pll = 3;
+ m_pll = m_n_int * n_pll + 1;
+ } else {
+ n_pll = 2;
+ m_pll = m_n_int * n_pll;
+ }
+ }
+
+ if (n_pll == 1) {
+ phy->pll_fbd_p = 0;
+ phy->pll_pre_div1p = 1;
+ } else {
+ phy->pll_fbd_p = n_pll;
+ phy->pll_pre_div1p = 0;
+ }
+
+ if (phy->pll_fbd_2p <= 7 && phy->pll_fbd_2p >= 4)
+ r_pll = 0x10 >> (7 - phy->pll_fbd_2p);
+
+ if (m_pll == 2) {
+ phy->pll_pre_p = 0;
+ phy->pll_fbd_s = 0;
+ phy->pll_fbd_div1f = 0;
+ phy->pll_fbd_div5f = 1;
+ } else if (m_pll >= 2 * 2 * r_pll && m_pll <= 2 * 4 * r_pll) {
+ phy->pll_pre_p = m_pll / (2 * r_pll);
+ phy->pll_fbd_s = 0;
+ phy->pll_fbd_div1f = 1;
+ phy->pll_fbd_div5f = 0;
+ } else if (m_pll >= 2 * 5 * r_pll && m_pll <= 2 * 150 * r_pll) {
+ if (((m_pll / (2 * r_pll)) % 2) == 0) {
+ phy->pll_pre_p =
+ (m_pll / (2 * r_pll)) / 2 - 1;
+ phy->pll_fbd_s =
+ (m_pll / (2 * r_pll)) % 2 + 2;
+ } else {
+ phy->pll_pre_p =
+ (m_pll / (2 * r_pll)) / 2;
+ phy->pll_fbd_s =
+ (m_pll / (2 * r_pll)) % 2;
+ }
+ phy->pll_fbd_div1f = 0;
+ phy->pll_fbd_div5f = 0;
+ } else {
+ phy->pll_pre_p = 0;
+ phy->pll_fbd_s = 0;
+ phy->pll_fbd_div1f = 0;
+ phy->pll_fbd_div5f = 1;
+ }
+
+ f_kHz = (u64)1000000000 * (u64)m_pll /
+ ((u64)ref_clk_ps * (u64)n_pll * (u64)q_pll);
+
+ if (f_kHz >= req_kHz)
+ break;
+
+ tmp_kHz += 10;
+
+ } while (true);
+
+ return f_kHz;
+}
+
+static void dsi_get_phy_params(u32 phy_req_kHz,
+ struct mipi_phy_params *phy)
+{
+ u32 ref_clk_ps = PHY_REF_CLK_PERIOD_PS;
+ u32 phy_rate_kHz;
+ u32 ui;
+
+ memset(phy, 0, sizeof(*phy));
+
+ phy_rate_kHz = dsi_calc_phy_rate(phy_req_kHz, phy);
+ if (!phy_rate_kHz)
+ return;
+
+ ui = 1000000 / phy_rate_kHz;
+
+ phy->clk_t_lpx = ROUND(50, 8 * ui);
+ phy->clk_t_hs_prepare = ROUND(133, 16 * ui) - 1;
+
+ phy->clk_t_hs_zero = ROUND(262, 8 * ui);
+ phy->clk_t_hs_trial = 2 * (ROUND(60, 8 * ui) - 1);
+ phy->clk_t_wakeup = ROUND(1000000, (ref_clk_ps / 1000) - 1);
+ if (phy->clk_t_wakeup > 0xff)
+ phy->clk_t_wakeup = 0xff;
+ phy->data_t_wakeup = phy->clk_t_wakeup;
+ phy->data_t_lpx = phy->clk_t_lpx;
+ phy->data_t_hs_prepare = ROUND(125 + 10 * ui, 16 * ui) - 1;
+ phy->data_t_hs_zero = ROUND(105 + 6 * ui, 8 * ui);
+ phy->data_t_hs_trial = 2 * (ROUND(60 + 4 * ui, 8 * ui) - 1);
+ phy->data_t_ta_go = 3;
+ phy->data_t_ta_get = 4;
+
+ phy->pll_enbwt = 1;
+ phy->clklp2hs_time = ROUND(407, 8 * ui) + 12;
+ phy->clkhs2lp_time = ROUND(105 + 12 * ui, 8 * ui);
+ phy->lp2hs_time = ROUND(240 + 12 * ui, 8 * ui) + 1;
+ phy->hs2lp_time = phy->clkhs2lp_time;
+ phy->clk_to_data_delay = 1 + phy->clklp2hs_time;
+ phy->data_to_clk_delay = ROUND(60 + 52 * ui, 8 * ui) +
+ phy->clkhs2lp_time;
+
+ phy->lane_byte_clk_kHz = phy_rate_kHz / 8;
+ phy->clk_division =
+ DIV_ROUND_UP(phy->lane_byte_clk_kHz, MAX_TX_ESC_CLK);
+}
+
+static u32 dsi_get_dpi_color_coding(enum mipi_dsi_pixel_format format)
+{
+ u32 val;
+
+ /*
+ * TODO: only support RGB888 now, to support more
+ */
+ switch (format) {
+ case MIPI_DSI_FMT_RGB888:
+ val = DSI_24BITS_1;
+ break;
+ default:
+ val = DSI_24BITS_1;
+ break;
+ }
+
+ return val;
+}
+
+/*
+ * dsi phy reg write function
+ */
+static void dsi_phy_tst_set(void __iomem *base, u32 reg, u32 val)
+{
+ u32 reg_write = 0x10000 + reg;
+
+ /*
+ * latch reg first
+ */
+ writel(reg_write, base + PHY_TST_CTRL1);
+ writel(0x02, base + PHY_TST_CTRL0);
+ writel(0x00, base + PHY_TST_CTRL0);
+
+ /*
+ * then latch value
+ */
+ writel(val, base + PHY_TST_CTRL1);
+ writel(0x02, base + PHY_TST_CTRL0);
+ writel(0x00, base + PHY_TST_CTRL0);
+}
+
+static void dsi_set_phy_timer(void __iomem *base,
+ struct mipi_phy_params *phy,
+ u32 lanes)
+{
+ u32 val;
+
+ /*
+ * Set lane value and phy stop wait time.
+ */
+ val = (lanes - 1) | (PHY_STOP_WAIT_TIME << 8);
+ writel(val, base + PHY_IF_CFG);
+
+ /*
+ * Set phy clk division.
+ */
+ val = readl(base + CLKMGR_CFG) | phy->clk_division;
+ writel(val, base + CLKMGR_CFG);
+
+ /*
+ * Set lp and hs switching params.
+ */
+ dw_update_bits(base + PHY_TMR_CFG, 24, MASK(8), phy->hs2lp_time);
+ dw_update_bits(base + PHY_TMR_CFG, 16, MASK(8), phy->lp2hs_time);
+ dw_update_bits(base + PHY_TMR_LPCLK_CFG, 16, MASK(10),
+ phy->clkhs2lp_time);
+ dw_update_bits(base + PHY_TMR_LPCLK_CFG, 0, MASK(10),
+ phy->clklp2hs_time);
+ dw_update_bits(base + CLK_DATA_TMR_CFG, 8, MASK(8),
+ phy->data_to_clk_delay);
+ dw_update_bits(base + CLK_DATA_TMR_CFG, 0, MASK(8),
+ phy->clk_to_data_delay);
+}
+
+static void dsi_set_mipi_phy(void __iomem *base,
+ struct mipi_phy_params *phy,
+ u32 lanes)
+{
+ u32 delay_count;
+ u32 val;
+ u32 i;
+
+ /* phy timer setting */
+ dsi_set_phy_timer(base, phy, lanes);
+
+ /*
+ * Reset to clean up phy tst params.
+ */
+ writel(0, base + PHY_RSTZ);
+ writel(0, base + PHY_TST_CTRL0);
+ writel(1, base + PHY_TST_CTRL0);
+ writel(0, base + PHY_TST_CTRL0);
+
+ /*
+ * Clock lane timing control setting: TLPX, THS-PREPARE,
+ * THS-ZERO, THS-TRAIL, TWAKEUP.
+ */
+ dsi_phy_tst_set(base, CLK_TLPX, phy->clk_t_lpx);
+ dsi_phy_tst_set(base, CLK_THS_PREPARE, phy->clk_t_hs_prepare);
+ dsi_phy_tst_set(base, CLK_THS_ZERO, phy->clk_t_hs_zero);
+ dsi_phy_tst_set(base, CLK_THS_TRAIL, phy->clk_t_hs_trial);
+ dsi_phy_tst_set(base, CLK_TWAKEUP, phy->clk_t_wakeup);
+
+ /*
+ * Data lane timing control setting: TLPX, THS-PREPARE,
+ * THS-ZERO, THS-TRAIL, TTA-GO, TTA-GET, TWAKEUP.
+ */
+ for (i = 0; i < lanes; i++) {
+ dsi_phy_tst_set(base, DATA_TLPX(i), phy->data_t_lpx);
+ dsi_phy_tst_set(base, DATA_THS_PREPARE(i),
+ phy->data_t_hs_prepare);
+ dsi_phy_tst_set(base, DATA_THS_ZERO(i), phy->data_t_hs_zero);
+ dsi_phy_tst_set(base, DATA_THS_TRAIL(i), phy->data_t_hs_trial);
+ dsi_phy_tst_set(base, DATA_TTA_GO(i), phy->data_t_ta_go);
+ dsi_phy_tst_set(base, DATA_TTA_GET(i), phy->data_t_ta_get);
+ dsi_phy_tst_set(base, DATA_TWAKEUP(i), phy->data_t_wakeup);
+ }
+
+ /*
+ * physical configuration: I, pll I, pll II, pll III,
+ * pll IV, pll V.
+ */
+ dsi_phy_tst_set(base, PHY_CFG_I, phy->hstx_ckg_sel);
+ val = (phy->pll_fbd_div5f << 5) + (phy->pll_fbd_div1f << 4) +
+ (phy->pll_fbd_2p << 1) + phy->pll_enbwt;
+ dsi_phy_tst_set(base, PHY_CFG_PLL_I, val);
+ dsi_phy_tst_set(base, PHY_CFG_PLL_II, phy->pll_fbd_p);
+ dsi_phy_tst_set(base, PHY_CFG_PLL_III, phy->pll_fbd_s);
+ val = (phy->pll_pre_div1p << 7) + phy->pll_pre_p;
+ dsi_phy_tst_set(base, PHY_CFG_PLL_IV, val);
+ val = (5 << 5) + (phy->pll_vco_750M << 4) + (phy->pll_lpf_rs << 2) +
+ phy->pll_lpf_cs;
+ dsi_phy_tst_set(base, PHY_CFG_PLL_V, val);
+
+ writel(PHY_ENABLECLK, base + PHY_RSTZ);
+ udelay(1);
+ writel(PHY_ENABLECLK | PHY_UNSHUTDOWNZ, base + PHY_RSTZ);
+ udelay(1);
+ writel(PHY_ENABLECLK | PHY_UNRSTZ | PHY_UNSHUTDOWNZ, base + PHY_RSTZ);
+ usleep_range(1000, 1500);
+
+ /*
+ * wait for phy's clock ready
+ */
+ delay_count = 100;
+ while (delay_count--) {
+ val = readl(base + PHY_STATUS);
+ if ((BIT(0) | BIT(2)) & val)
+ break;
+
+ udelay(1);
+ }
+
+ if (!delay_count)
+ DRM_INFO("phylock and phystopstateclklane is not ready.\n");
+}
+
+static void dsi_set_mode_timing(void __iomem *base,
+ u32 lane_byte_clk_kHz,
+ struct drm_display_mode *mode,
+ enum mipi_dsi_pixel_format format)
+{
+ u32 hfp, hbp, hsw, vfp, vbp, vsw;
+ u32 hline_time;
+ u32 hsa_time;
+ u32 hbp_time;
+ u32 pixel_clk_kHz;
+ int htot, vtot;
+ u32 val;
+ u64 tmp;
+
+ val = dsi_get_dpi_color_coding(format);
+ writel(val, base + DPI_COLOR_CODING);
+
+ val = (mode->flags & DRM_MODE_FLAG_NHSYNC ? 1 : 0) << 2;
+ val |= (mode->flags & DRM_MODE_FLAG_NVSYNC ? 1 : 0) << 1;
+ writel(val, base + DPI_CFG_POL);
+
+ /*
+ * The DSI IP accepts vertical timing using lines as normal,
+ * but horizontal timing is a mixture of pixel-clocks for the
+ * active region and byte-lane clocks for the blanking-related
+ * timings. hfp is specified as the total hline_time in byte-
+ * lane clocks minus hsa, hbp and active.
+ */
+ pixel_clk_kHz = mode->clock;
+ htot = mode->htotal;
+ vtot = mode->vtotal;
+ hfp = mode->hsync_start - mode->hdisplay;
+ hbp = mode->htotal - mode->hsync_end;
+ hsw = mode->hsync_end - mode->hsync_start;
+ vfp = mode->vsync_start - mode->vdisplay;
+ vbp = mode->vtotal - mode->vsync_end;
+ vsw = mode->vsync_end - mode->vsync_start;
+ if (vsw > 15) {
+ DRM_DEBUG_DRIVER("vsw exceeded 15\n");
+ vsw = 15;
+ }
+
+ hsa_time = (hsw * lane_byte_clk_kHz) / pixel_clk_kHz;
+ hbp_time = (hbp * lane_byte_clk_kHz) / pixel_clk_kHz;
+ tmp = (u64)htot * (u64)lane_byte_clk_kHz;
+ hline_time = DIV_ROUND_UP(tmp, pixel_clk_kHz);
+
+ /* all specified in byte-lane clocks */
+ writel(hsa_time, base + VID_HSA_TIME);
+ writel(hbp_time, base + VID_HBP_TIME);
+ writel(hline_time, base + VID_HLINE_TIME);
+
+ writel(vsw, base + VID_VSA_LINES);
+ writel(vbp, base + VID_VBP_LINES);
+ writel(vfp, base + VID_VFP_LINES);
+ writel(mode->vdisplay, base + VID_VACTIVE_LINES);
+ writel(mode->hdisplay, base + VID_PKT_SIZE);
+
+ DRM_DEBUG_DRIVER("htot=%d, hfp=%d, hbp=%d, hsw=%d\n",
+ htot, hfp, hbp, hsw);
+ DRM_DEBUG_DRIVER("vtol=%d, vfp=%d, vbp=%d, vsw=%d\n",
+ vtot, vfp, vbp, vsw);
+ DRM_DEBUG_DRIVER("hsa_time=%d, hbp_time=%d, hline_time=%d\n",
+ hsa_time, hbp_time, hline_time);
+}
+
+static void dsi_set_video_mode(void __iomem *base, unsigned long flags)
+{
+ u32 val;
+ u32 mode_mask = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+ u32 non_burst_sync_pulse = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+ u32 non_burst_sync_event = MIPI_DSI_MODE_VIDEO;
+
+ /*
+ * choose video mode type
+ */
+ if ((flags & mode_mask) == non_burst_sync_pulse)
+ val = DSI_NON_BURST_SYNC_PULSES;
+ else if ((flags & mode_mask) == non_burst_sync_event)
+ val = DSI_NON_BURST_SYNC_EVENTS;
+ else
+ val = DSI_BURST_SYNC_PULSES_1;
+ writel(val, base + VID_MODE_CFG);
+
+ writel(PHY_TXREQUESTCLKHS, base + LPCLK_CTRL);
+ writel(DSI_VIDEO_MODE, base + MODE_CFG);
+}
+
+static void dsi_mipi_init(struct dw_dsi *dsi)
+{
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ struct mipi_phy_params *phy = &dsi->phy;
+ struct drm_display_mode *mode = &dsi->cur_mode;
+ u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+ void __iomem *base = ctx->base;
+ u32 dphy_req_kHz;
+
+ /*
+ * count phy params
+ */
+ dphy_req_kHz = mode->clock * bpp / dsi->lanes;
+ dsi_get_phy_params(dphy_req_kHz, phy);
+
+ /* reset Core */
+ writel(RESET, base + PWR_UP);
+
+ /* set dsi phy params */
+ dsi_set_mipi_phy(base, phy, dsi->lanes);
+
+ /* set dsi mode timing */
+ dsi_set_mode_timing(base, phy->lane_byte_clk_kHz, mode, dsi->format);
+
+ /* set dsi video mode */
+ dsi_set_video_mode(base, dsi->mode_flags);
+
+ /* dsi wake up */
+ writel(POWERUP, base + PWR_UP);
+
+ DRM_DEBUG_DRIVER("lanes=%d, pixel_clk=%d kHz, bytes_freq=%d kHz\n",
+ dsi->lanes, mode->clock, phy->lane_byte_clk_kHz);
+}
+
+static void dsi_encoder_disable(struct drm_encoder *encoder)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ void __iomem *base = ctx->base;
+
+ if (!dsi->enable)
+ return;
+
+ writel(0, base + PWR_UP);
+ writel(0, base + LPCLK_CTRL);
+ writel(0, base + PHY_RSTZ);
+ clk_disable_unprepare(ctx->pclk);
+
+ dsi->enable = false;
+}
+
+static void dsi_encoder_enable(struct drm_encoder *encoder)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ int ret;
+
+ if (dsi->enable)
+ return;
+
+ ret = clk_prepare_enable(ctx->pclk);
+ if (ret) {
+ DRM_ERROR("fail to enable pclk: %d\n", ret);
+ return;
+ }
+
+ dsi_mipi_init(dsi);
+
+ dsi->enable = true;
+}
+
+static void dsi_encoder_mode_set(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+
+ drm_mode_copy(&dsi->cur_mode, adj_mode);
+}
+
+static int dsi_encoder_atomic_check(struct drm_encoder *encoder,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state)
+{
+ /* do nothing */
+ return 0;
+}
+
+static const struct drm_encoder_helper_funcs dw_encoder_helper_funcs = {
+ .atomic_check = dsi_encoder_atomic_check,
+ .mode_set = dsi_encoder_mode_set,
+ .enable = dsi_encoder_enable,
+ .disable = dsi_encoder_disable
+};
+
+static const struct drm_encoder_funcs dw_encoder_funcs = {
+ .destroy = drm_encoder_cleanup,
+};
+
+static int dw_drm_encoder_init(struct device *dev,
+ struct drm_device *drm_dev,
+ struct drm_encoder *encoder)
+{
+ int ret;
+ u32 crtc_mask = drm_of_find_possible_crtcs(drm_dev, dev->of_node);
+
+ if (!crtc_mask) {
+ DRM_ERROR("failed to find crtc mask\n");
+ return -EINVAL;
+ }
+
+ encoder->possible_crtcs = crtc_mask;
+ ret = drm_encoder_init(drm_dev, encoder, &dw_encoder_funcs,
+ DRM_MODE_ENCODER_DSI, NULL);
+ if (ret) {
+ DRM_ERROR("failed to init dsi encoder\n");
+ return ret;
+ }
+
+ drm_encoder_helper_add(encoder, &dw_encoder_helper_funcs);
+
+ return 0;
+}
+
+static int dsi_bind(struct device *dev, struct device *master, void *data)
+{
+ struct dsi_data *ddata = dev_get_drvdata(dev);
+ struct dw_dsi *dsi = &ddata->dsi;
+ struct drm_device *drm_dev = data;
+ int ret;
+
+ ret = dw_drm_encoder_init(dev, drm_dev, &dsi->encoder);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void dsi_unbind(struct device *dev, struct device *master, void *data)
+{
+ /* do nothing */
+}
+
+static const struct component_ops dsi_ops = {
+ .bind = dsi_bind,
+ .unbind = dsi_unbind,
+};
+
+static int dsi_parse_dt(struct platform_device *pdev, struct dw_dsi *dsi)
+{
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ struct resource *res;
+
+ ctx->pclk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(ctx->pclk)) {
+ DRM_ERROR("failed to get pclk clock\n");
+ return PTR_ERR(ctx->pclk);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ctx->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(ctx->base)) {
+ DRM_ERROR("failed to remap dsi io region\n");
+ return PTR_ERR(ctx->base);
+ }
+
+ return 0;
+}
+
+static int dsi_probe(struct platform_device *pdev)
+{
+ struct dsi_data *data;
+ struct dw_dsi *dsi;
+ struct dsi_hw_ctx *ctx;
+ int ret;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data) {
+ DRM_ERROR("failed to allocate dsi data.\n");
+ return -ENOMEM;
+ }
+ dsi = &data->dsi;
+ ctx = &data->ctx;
+ dsi->ctx = ctx;
+
+ ret = dsi_parse_dt(pdev, dsi);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, data);
+
+ return component_add(&pdev->dev, &dsi_ops);
+}
+
+static int dsi_remove(struct platform_device *pdev)
+{
+ component_del(&pdev->dev, &dsi_ops);
+
+ return 0;
+}
+
+static const struct of_device_id dsi_of_match[] = {
+ {.compatible = "hisilicon,hi6220-dsi"},
+ { }
+};
+MODULE_DEVICE_TABLE(of, dsi_of_match);
+
+static struct platform_driver dsi_driver = {
+ .probe = dsi_probe,
+ .remove = dsi_remove,
+ .driver = {
+ .name = "dw-dsi",
+ .of_match_table = dsi_of_match,
+ },
+};
+
+module_platform_driver(dsi_driver);
+
+MODULE_AUTHOR("Xinliang Liu <xinliang.liu@linaro.org>");
+MODULE_AUTHOR("Xinliang Liu <z.liuxinliang@hisilicon.com>");
+MODULE_AUTHOR("Xinwei Kong <kong.kongxinwei@hisilicon.com>");
+MODULE_DESCRIPTION("DesignWare MIPI DSI Host Controller v1.02 driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h b/drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
new file mode 100644
index 000000000000..18808fc9f362
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
@@ -0,0 +1,103 @@
+/*
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __DW_DSI_REG_H__
+#define __DW_DSI_REG_H__
+
+#define MASK(x) (BIT(x) - 1)
+
+/*
+ * regs
+ */
+#define PWR_UP 0x04 /* Core power-up */
+#define RESET 0
+#define POWERUP BIT(0)
+#define PHY_IF_CFG 0xA4 /* D-PHY interface configuration */
+#define CLKMGR_CFG 0x08 /* the internal clock dividers */
+#define PHY_RSTZ 0xA0 /* D-PHY reset control */
+#define PHY_ENABLECLK BIT(2)
+#define PHY_UNRSTZ BIT(1)
+#define PHY_UNSHUTDOWNZ BIT(0)
+#define PHY_TST_CTRL0 0xB4 /* D-PHY test interface control 0 */
+#define PHY_TST_CTRL1 0xB8 /* D-PHY test interface control 1 */
+#define CLK_TLPX 0x10
+#define CLK_THS_PREPARE 0x11
+#define CLK_THS_ZERO 0x12
+#define CLK_THS_TRAIL 0x13
+#define CLK_TWAKEUP 0x14
+#define DATA_TLPX(x) (0x20 + ((x) << 4))
+#define DATA_THS_PREPARE(x) (0x21 + ((x) << 4))
+#define DATA_THS_ZERO(x) (0x22 + ((x) << 4))
+#define DATA_THS_TRAIL(x) (0x23 + ((x) << 4))
+#define DATA_TTA_GO(x) (0x24 + ((x) << 4))
+#define DATA_TTA_GET(x) (0x25 + ((x) << 4))
+#define DATA_TWAKEUP(x) (0x26 + ((x) << 4))
+#define PHY_CFG_I 0x60
+#define PHY_CFG_PLL_I 0x63
+#define PHY_CFG_PLL_II 0x64
+#define PHY_CFG_PLL_III 0x65
+#define PHY_CFG_PLL_IV 0x66
+#define PHY_CFG_PLL_V 0x67
+#define DPI_COLOR_CODING 0x10 /* DPI color coding */
+#define DPI_CFG_POL 0x14 /* DPI polarity configuration */
+#define VID_HSA_TIME 0x48 /* Horizontal Sync Active time */
+#define VID_HBP_TIME 0x4C /* Horizontal Back Porch time */
+#define VID_HLINE_TIME 0x50 /* Line time */
+#define VID_VSA_LINES 0x54 /* Vertical Sync Active period */
+#define VID_VBP_LINES 0x58 /* Vertical Back Porch period */
+#define VID_VFP_LINES 0x5C /* Vertical Front Porch period */
+#define VID_VACTIVE_LINES 0x60 /* Vertical resolution */
+#define VID_PKT_SIZE 0x3C /* Video packet size */
+#define VID_MODE_CFG 0x38 /* Video mode configuration */
+#define PHY_TMR_CFG 0x9C /* Data lanes timing configuration */
+#define BTA_TO_CNT 0x8C /* Response timeout definition */
+#define PHY_TMR_LPCLK_CFG 0x98 /* clock lane timing configuration */
+#define CLK_DATA_TMR_CFG 0xCC
+#define LPCLK_CTRL 0x94 /* Low-power in clock lane */
+#define PHY_TXREQUESTCLKHS BIT(0)
+#define MODE_CFG 0x34 /* Video or Command mode selection */
+#define PHY_STATUS 0xB0 /* D-PHY PPI status interface */
+
+#define PHY_STOP_WAIT_TIME 0x30
+
+/*
+ * regs relevant enum
+ */
+enum dpi_color_coding {
+ DSI_24BITS_1 = 5,
+};
+
+enum dsi_video_mode_type {
+ DSI_NON_BURST_SYNC_PULSES = 0,
+ DSI_NON_BURST_SYNC_EVENTS,
+ DSI_BURST_SYNC_PULSES_1,
+ DSI_BURST_SYNC_PULSES_2
+};
+
+enum dsi_work_mode {
+ DSI_VIDEO_MODE = 0,
+ DSI_COMMAND_MODE
+};
+
+/*
+ * Register Write/Read Helper functions
+ */
+static inline void dw_update_bits(void __iomem *addr, u32 bit_start,
+ u32 mask, u32 val)
+{
+ u32 tmp, orig;
+
+ orig = readl(addr);
+ tmp = orig & ~(mask << bit_start);
+ tmp |= (val & mask) << bit_start;
+ writel(tmp, addr);
+}
+
+#endif /* __DW_DRM_DSI_H__ */
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 07/10] drm/hisilicon: Add designware dsi encoder driver
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add DesignWare MIPI DSI Host Controller v1.02 encoder driver
for hi6220 SoC.
v8: None.
v7:
- A few regs define clean up.
v6:
- Change "pclk_dsi" to "pclk".
v5: None.
v4: None.
v3:
- Rename file name to dw_drm_dsi.c
- Make encoder type as DRM_MODE_ENCODER_DSI.
- A few cleanup.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Andy Green <andy.green@linaro.org>
---
drivers/gpu/drm/hisilicon/kirin/Kconfig | 1 +
drivers/gpu/drm/hisilicon/kirin/Makefile | 3 +-
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 755 +++++++++++++++++++++++++++
drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++++
4 files changed, 861 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
diff --git a/drivers/gpu/drm/hisilicon/kirin/Kconfig b/drivers/gpu/drm/hisilicon/kirin/Kconfig
index 3ac4b8edeac1..de0d454c5c13 100644
--- a/drivers/gpu/drm/hisilicon/kirin/Kconfig
+++ b/drivers/gpu/drm/hisilicon/kirin/Kconfig
@@ -4,6 +4,7 @@ config DRM_HISI_KIRIN
select DRM_KMS_HELPER
select DRM_GEM_CMA_HELPER
select DRM_KMS_CMA_HELPER
+ select DRM_MIPI_DSI
help
Choose this option if you have a hisilicon Kirin chipsets(hi6220).
If M is selected the module will be called kirin-drm.
diff --git a/drivers/gpu/drm/hisilicon/kirin/Makefile b/drivers/gpu/drm/hisilicon/kirin/Makefile
index 2a61ab006ddb..5dcd0d4328b6 100644
--- a/drivers/gpu/drm/hisilicon/kirin/Makefile
+++ b/drivers/gpu/drm/hisilicon/kirin/Makefile
@@ -1,4 +1,5 @@
kirin-drm-y := kirin_drm_drv.o \
- kirin_drm_ade.o
+ kirin_drm_ade.o \
+ dw_drm_dsi.o
obj-$(CONFIG_DRM_HISI_KIRIN) += kirin-drm.o
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
new file mode 100644
index 000000000000..1a930b77ec53
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
@@ -0,0 +1,755 @@
+/*
+ * DesignWare MIPI DSI Host Controller v1.02 driver
+ *
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * Author:
+ * Xinliang Liu <z.liuxinliang@hisilicon.com>
+ * Xinliang Liu <xinliang.liu@linaro.org>
+ * Xinwei Kong <kong.kongxinwei@hisilicon.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/of_graph.h>
+
+#include <drm/drm_of.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_encoder_slave.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "dw_dsi_reg.h"
+
+#define MAX_TX_ESC_CLK 10
+#define ROUND(x, y) ((x) / (y) + \
+ ((x) % (y) * 10 / (y) >= 5 ? 1 : 0))
+#define PHY_REF_CLK_RATE 19200000
+#define PHY_REF_CLK_PERIOD_PS (1000000000 / (PHY_REF_CLK_RATE / 1000))
+
+#define encoder_to_dsi(encoder) \
+ container_of(encoder, struct dw_dsi, encoder)
+#define host_to_dsi(host) \
+ container_of(host, struct dw_dsi, host)
+
+struct mipi_phy_params {
+ u32 clk_t_lpx;
+ u32 clk_t_hs_prepare;
+ u32 clk_t_hs_zero;
+ u32 clk_t_hs_trial;
+ u32 clk_t_wakeup;
+ u32 data_t_lpx;
+ u32 data_t_hs_prepare;
+ u32 data_t_hs_zero;
+ u32 data_t_hs_trial;
+ u32 data_t_ta_go;
+ u32 data_t_ta_get;
+ u32 data_t_wakeup;
+ u32 hstx_ckg_sel;
+ u32 pll_fbd_div5f;
+ u32 pll_fbd_div1f;
+ u32 pll_fbd_2p;
+ u32 pll_enbwt;
+ u32 pll_fbd_p;
+ u32 pll_fbd_s;
+ u32 pll_pre_div1p;
+ u32 pll_pre_p;
+ u32 pll_vco_750M;
+ u32 pll_lpf_rs;
+ u32 pll_lpf_cs;
+ u32 clklp2hs_time;
+ u32 clkhs2lp_time;
+ u32 lp2hs_time;
+ u32 hs2lp_time;
+ u32 clk_to_data_delay;
+ u32 data_to_clk_delay;
+ u32 lane_byte_clk_kHz;
+ u32 clk_division;
+};
+
+struct dsi_hw_ctx {
+ void __iomem *base;
+ struct clk *pclk;
+};
+
+struct dw_dsi {
+ struct drm_encoder encoder;
+ struct drm_display_mode cur_mode;
+ struct dsi_hw_ctx *ctx;
+ struct mipi_phy_params phy;
+
+ u32 lanes;
+ enum mipi_dsi_pixel_format format;
+ unsigned long mode_flags;
+ bool enable;
+};
+
+struct dsi_data {
+ struct dw_dsi dsi;
+ struct dsi_hw_ctx ctx;
+};
+
+struct dsi_phy_range {
+ u32 min_range_kHz;
+ u32 max_range_kHz;
+ u32 pll_vco_750M;
+ u32 hstx_ckg_sel;
+};
+
+static const struct dsi_phy_range dphy_range_info[] = {
+ { 46875, 62500, 1, 7 },
+ { 62500, 93750, 0, 7 },
+ { 93750, 125000, 1, 6 },
+ { 125000, 187500, 0, 6 },
+ { 187500, 250000, 1, 5 },
+ { 250000, 375000, 0, 5 },
+ { 375000, 500000, 1, 4 },
+ { 500000, 750000, 0, 4 },
+ { 750000, 1000000, 1, 0 },
+ { 1000000, 1500000, 0, 0 }
+};
+
+static u32 dsi_calc_phy_rate(u32 req_kHz, struct mipi_phy_params *phy)
+{
+ u32 ref_clk_ps = PHY_REF_CLK_PERIOD_PS;
+ u32 tmp_kHz = req_kHz;
+ u32 i = 0;
+ u32 q_pll = 1;
+ u32 m_pll = 0;
+ u32 n_pll = 0;
+ u32 r_pll = 1;
+ u32 m_n = 0;
+ u32 m_n_int = 0;
+ u32 f_kHz = 0;
+ u64 temp;
+
+ /*
+ * Find a rate >= req_kHz.
+ */
+ do {
+ f_kHz = tmp_kHz;
+
+ for (i = 0; i < ARRAY_SIZE(dphy_range_info); i++)
+ if (f_kHz >= dphy_range_info[i].min_range_kHz &&
+ f_kHz <= dphy_range_info[i].max_range_kHz)
+ break;
+
+ if (i == ARRAY_SIZE(dphy_range_info)) {
+ DRM_ERROR("%dkHz out of range\n", f_kHz);
+ return 0;
+ }
+
+ phy->pll_vco_750M = dphy_range_info[i].pll_vco_750M;
+ phy->hstx_ckg_sel = dphy_range_info[i].hstx_ckg_sel;
+
+ if (phy->hstx_ckg_sel <= 7 &&
+ phy->hstx_ckg_sel >= 4)
+ q_pll = 0x10 >> (7 - phy->hstx_ckg_sel);
+
+ temp = f_kHz * (u64)q_pll * (u64)ref_clk_ps;
+ m_n_int = temp / (u64)1000000000;
+ m_n = (temp % (u64)1000000000) / (u64)100000000;
+
+ if (m_n_int % 2 == 0) {
+ if (m_n * 6 >= 50) {
+ n_pll = 2;
+ m_pll = (m_n_int + 1) * n_pll;
+ } else if (m_n * 6 >= 30) {
+ n_pll = 3;
+ m_pll = m_n_int * n_pll + 2;
+ } else {
+ n_pll = 1;
+ m_pll = m_n_int * n_pll;
+ }
+ } else {
+ if (m_n * 6 >= 50) {
+ n_pll = 1;
+ m_pll = (m_n_int + 1) * n_pll;
+ } else if (m_n * 6 >= 30) {
+ n_pll = 1;
+ m_pll = (m_n_int + 1) * n_pll;
+ } else if (m_n * 6 >= 10) {
+ n_pll = 3;
+ m_pll = m_n_int * n_pll + 1;
+ } else {
+ n_pll = 2;
+ m_pll = m_n_int * n_pll;
+ }
+ }
+
+ if (n_pll == 1) {
+ phy->pll_fbd_p = 0;
+ phy->pll_pre_div1p = 1;
+ } else {
+ phy->pll_fbd_p = n_pll;
+ phy->pll_pre_div1p = 0;
+ }
+
+ if (phy->pll_fbd_2p <= 7 && phy->pll_fbd_2p >= 4)
+ r_pll = 0x10 >> (7 - phy->pll_fbd_2p);
+
+ if (m_pll == 2) {
+ phy->pll_pre_p = 0;
+ phy->pll_fbd_s = 0;
+ phy->pll_fbd_div1f = 0;
+ phy->pll_fbd_div5f = 1;
+ } else if (m_pll >= 2 * 2 * r_pll && m_pll <= 2 * 4 * r_pll) {
+ phy->pll_pre_p = m_pll / (2 * r_pll);
+ phy->pll_fbd_s = 0;
+ phy->pll_fbd_div1f = 1;
+ phy->pll_fbd_div5f = 0;
+ } else if (m_pll >= 2 * 5 * r_pll && m_pll <= 2 * 150 * r_pll) {
+ if (((m_pll / (2 * r_pll)) % 2) == 0) {
+ phy->pll_pre_p =
+ (m_pll / (2 * r_pll)) / 2 - 1;
+ phy->pll_fbd_s =
+ (m_pll / (2 * r_pll)) % 2 + 2;
+ } else {
+ phy->pll_pre_p =
+ (m_pll / (2 * r_pll)) / 2;
+ phy->pll_fbd_s =
+ (m_pll / (2 * r_pll)) % 2;
+ }
+ phy->pll_fbd_div1f = 0;
+ phy->pll_fbd_div5f = 0;
+ } else {
+ phy->pll_pre_p = 0;
+ phy->pll_fbd_s = 0;
+ phy->pll_fbd_div1f = 0;
+ phy->pll_fbd_div5f = 1;
+ }
+
+ f_kHz = (u64)1000000000 * (u64)m_pll /
+ ((u64)ref_clk_ps * (u64)n_pll * (u64)q_pll);
+
+ if (f_kHz >= req_kHz)
+ break;
+
+ tmp_kHz += 10;
+
+ } while (true);
+
+ return f_kHz;
+}
+
+static void dsi_get_phy_params(u32 phy_req_kHz,
+ struct mipi_phy_params *phy)
+{
+ u32 ref_clk_ps = PHY_REF_CLK_PERIOD_PS;
+ u32 phy_rate_kHz;
+ u32 ui;
+
+ memset(phy, 0, sizeof(*phy));
+
+ phy_rate_kHz = dsi_calc_phy_rate(phy_req_kHz, phy);
+ if (!phy_rate_kHz)
+ return;
+
+ ui = 1000000 / phy_rate_kHz;
+
+ phy->clk_t_lpx = ROUND(50, 8 * ui);
+ phy->clk_t_hs_prepare = ROUND(133, 16 * ui) - 1;
+
+ phy->clk_t_hs_zero = ROUND(262, 8 * ui);
+ phy->clk_t_hs_trial = 2 * (ROUND(60, 8 * ui) - 1);
+ phy->clk_t_wakeup = ROUND(1000000, (ref_clk_ps / 1000) - 1);
+ if (phy->clk_t_wakeup > 0xff)
+ phy->clk_t_wakeup = 0xff;
+ phy->data_t_wakeup = phy->clk_t_wakeup;
+ phy->data_t_lpx = phy->clk_t_lpx;
+ phy->data_t_hs_prepare = ROUND(125 + 10 * ui, 16 * ui) - 1;
+ phy->data_t_hs_zero = ROUND(105 + 6 * ui, 8 * ui);
+ phy->data_t_hs_trial = 2 * (ROUND(60 + 4 * ui, 8 * ui) - 1);
+ phy->data_t_ta_go = 3;
+ phy->data_t_ta_get = 4;
+
+ phy->pll_enbwt = 1;
+ phy->clklp2hs_time = ROUND(407, 8 * ui) + 12;
+ phy->clkhs2lp_time = ROUND(105 + 12 * ui, 8 * ui);
+ phy->lp2hs_time = ROUND(240 + 12 * ui, 8 * ui) + 1;
+ phy->hs2lp_time = phy->clkhs2lp_time;
+ phy->clk_to_data_delay = 1 + phy->clklp2hs_time;
+ phy->data_to_clk_delay = ROUND(60 + 52 * ui, 8 * ui) +
+ phy->clkhs2lp_time;
+
+ phy->lane_byte_clk_kHz = phy_rate_kHz / 8;
+ phy->clk_division =
+ DIV_ROUND_UP(phy->lane_byte_clk_kHz, MAX_TX_ESC_CLK);
+}
+
+static u32 dsi_get_dpi_color_coding(enum mipi_dsi_pixel_format format)
+{
+ u32 val;
+
+ /*
+ * TODO: only support RGB888 now, to support more
+ */
+ switch (format) {
+ case MIPI_DSI_FMT_RGB888:
+ val = DSI_24BITS_1;
+ break;
+ default:
+ val = DSI_24BITS_1;
+ break;
+ }
+
+ return val;
+}
+
+/*
+ * dsi phy reg write function
+ */
+static void dsi_phy_tst_set(void __iomem *base, u32 reg, u32 val)
+{
+ u32 reg_write = 0x10000 + reg;
+
+ /*
+ * latch reg first
+ */
+ writel(reg_write, base + PHY_TST_CTRL1);
+ writel(0x02, base + PHY_TST_CTRL0);
+ writel(0x00, base + PHY_TST_CTRL0);
+
+ /*
+ * then latch value
+ */
+ writel(val, base + PHY_TST_CTRL1);
+ writel(0x02, base + PHY_TST_CTRL0);
+ writel(0x00, base + PHY_TST_CTRL0);
+}
+
+static void dsi_set_phy_timer(void __iomem *base,
+ struct mipi_phy_params *phy,
+ u32 lanes)
+{
+ u32 val;
+
+ /*
+ * Set lane value and phy stop wait time.
+ */
+ val = (lanes - 1) | (PHY_STOP_WAIT_TIME << 8);
+ writel(val, base + PHY_IF_CFG);
+
+ /*
+ * Set phy clk division.
+ */
+ val = readl(base + CLKMGR_CFG) | phy->clk_division;
+ writel(val, base + CLKMGR_CFG);
+
+ /*
+ * Set lp and hs switching params.
+ */
+ dw_update_bits(base + PHY_TMR_CFG, 24, MASK(8), phy->hs2lp_time);
+ dw_update_bits(base + PHY_TMR_CFG, 16, MASK(8), phy->lp2hs_time);
+ dw_update_bits(base + PHY_TMR_LPCLK_CFG, 16, MASK(10),
+ phy->clkhs2lp_time);
+ dw_update_bits(base + PHY_TMR_LPCLK_CFG, 0, MASK(10),
+ phy->clklp2hs_time);
+ dw_update_bits(base + CLK_DATA_TMR_CFG, 8, MASK(8),
+ phy->data_to_clk_delay);
+ dw_update_bits(base + CLK_DATA_TMR_CFG, 0, MASK(8),
+ phy->clk_to_data_delay);
+}
+
+static void dsi_set_mipi_phy(void __iomem *base,
+ struct mipi_phy_params *phy,
+ u32 lanes)
+{
+ u32 delay_count;
+ u32 val;
+ u32 i;
+
+ /* phy timer setting */
+ dsi_set_phy_timer(base, phy, lanes);
+
+ /*
+ * Reset to clean up phy tst params.
+ */
+ writel(0, base + PHY_RSTZ);
+ writel(0, base + PHY_TST_CTRL0);
+ writel(1, base + PHY_TST_CTRL0);
+ writel(0, base + PHY_TST_CTRL0);
+
+ /*
+ * Clock lane timing control setting: TLPX, THS-PREPARE,
+ * THS-ZERO, THS-TRAIL, TWAKEUP.
+ */
+ dsi_phy_tst_set(base, CLK_TLPX, phy->clk_t_lpx);
+ dsi_phy_tst_set(base, CLK_THS_PREPARE, phy->clk_t_hs_prepare);
+ dsi_phy_tst_set(base, CLK_THS_ZERO, phy->clk_t_hs_zero);
+ dsi_phy_tst_set(base, CLK_THS_TRAIL, phy->clk_t_hs_trial);
+ dsi_phy_tst_set(base, CLK_TWAKEUP, phy->clk_t_wakeup);
+
+ /*
+ * Data lane timing control setting: TLPX, THS-PREPARE,
+ * THS-ZERO, THS-TRAIL, TTA-GO, TTA-GET, TWAKEUP.
+ */
+ for (i = 0; i < lanes; i++) {
+ dsi_phy_tst_set(base, DATA_TLPX(i), phy->data_t_lpx);
+ dsi_phy_tst_set(base, DATA_THS_PREPARE(i),
+ phy->data_t_hs_prepare);
+ dsi_phy_tst_set(base, DATA_THS_ZERO(i), phy->data_t_hs_zero);
+ dsi_phy_tst_set(base, DATA_THS_TRAIL(i), phy->data_t_hs_trial);
+ dsi_phy_tst_set(base, DATA_TTA_GO(i), phy->data_t_ta_go);
+ dsi_phy_tst_set(base, DATA_TTA_GET(i), phy->data_t_ta_get);
+ dsi_phy_tst_set(base, DATA_TWAKEUP(i), phy->data_t_wakeup);
+ }
+
+ /*
+ * physical configuration: I, pll I, pll II, pll III,
+ * pll IV, pll V.
+ */
+ dsi_phy_tst_set(base, PHY_CFG_I, phy->hstx_ckg_sel);
+ val = (phy->pll_fbd_div5f << 5) + (phy->pll_fbd_div1f << 4) +
+ (phy->pll_fbd_2p << 1) + phy->pll_enbwt;
+ dsi_phy_tst_set(base, PHY_CFG_PLL_I, val);
+ dsi_phy_tst_set(base, PHY_CFG_PLL_II, phy->pll_fbd_p);
+ dsi_phy_tst_set(base, PHY_CFG_PLL_III, phy->pll_fbd_s);
+ val = (phy->pll_pre_div1p << 7) + phy->pll_pre_p;
+ dsi_phy_tst_set(base, PHY_CFG_PLL_IV, val);
+ val = (5 << 5) + (phy->pll_vco_750M << 4) + (phy->pll_lpf_rs << 2) +
+ phy->pll_lpf_cs;
+ dsi_phy_tst_set(base, PHY_CFG_PLL_V, val);
+
+ writel(PHY_ENABLECLK, base + PHY_RSTZ);
+ udelay(1);
+ writel(PHY_ENABLECLK | PHY_UNSHUTDOWNZ, base + PHY_RSTZ);
+ udelay(1);
+ writel(PHY_ENABLECLK | PHY_UNRSTZ | PHY_UNSHUTDOWNZ, base + PHY_RSTZ);
+ usleep_range(1000, 1500);
+
+ /*
+ * wait for phy's clock ready
+ */
+ delay_count = 100;
+ while (delay_count--) {
+ val = readl(base + PHY_STATUS);
+ if ((BIT(0) | BIT(2)) & val)
+ break;
+
+ udelay(1);
+ }
+
+ if (!delay_count)
+ DRM_INFO("phylock and phystopstateclklane is not ready.\n");
+}
+
+static void dsi_set_mode_timing(void __iomem *base,
+ u32 lane_byte_clk_kHz,
+ struct drm_display_mode *mode,
+ enum mipi_dsi_pixel_format format)
+{
+ u32 hfp, hbp, hsw, vfp, vbp, vsw;
+ u32 hline_time;
+ u32 hsa_time;
+ u32 hbp_time;
+ u32 pixel_clk_kHz;
+ int htot, vtot;
+ u32 val;
+ u64 tmp;
+
+ val = dsi_get_dpi_color_coding(format);
+ writel(val, base + DPI_COLOR_CODING);
+
+ val = (mode->flags & DRM_MODE_FLAG_NHSYNC ? 1 : 0) << 2;
+ val |= (mode->flags & DRM_MODE_FLAG_NVSYNC ? 1 : 0) << 1;
+ writel(val, base + DPI_CFG_POL);
+
+ /*
+ * The DSI IP accepts vertical timing using lines as normal,
+ * but horizontal timing is a mixture of pixel-clocks for the
+ * active region and byte-lane clocks for the blanking-related
+ * timings. hfp is specified as the total hline_time in byte-
+ * lane clocks minus hsa, hbp and active.
+ */
+ pixel_clk_kHz = mode->clock;
+ htot = mode->htotal;
+ vtot = mode->vtotal;
+ hfp = mode->hsync_start - mode->hdisplay;
+ hbp = mode->htotal - mode->hsync_end;
+ hsw = mode->hsync_end - mode->hsync_start;
+ vfp = mode->vsync_start - mode->vdisplay;
+ vbp = mode->vtotal - mode->vsync_end;
+ vsw = mode->vsync_end - mode->vsync_start;
+ if (vsw > 15) {
+ DRM_DEBUG_DRIVER("vsw exceeded 15\n");
+ vsw = 15;
+ }
+
+ hsa_time = (hsw * lane_byte_clk_kHz) / pixel_clk_kHz;
+ hbp_time = (hbp * lane_byte_clk_kHz) / pixel_clk_kHz;
+ tmp = (u64)htot * (u64)lane_byte_clk_kHz;
+ hline_time = DIV_ROUND_UP(tmp, pixel_clk_kHz);
+
+ /* all specified in byte-lane clocks */
+ writel(hsa_time, base + VID_HSA_TIME);
+ writel(hbp_time, base + VID_HBP_TIME);
+ writel(hline_time, base + VID_HLINE_TIME);
+
+ writel(vsw, base + VID_VSA_LINES);
+ writel(vbp, base + VID_VBP_LINES);
+ writel(vfp, base + VID_VFP_LINES);
+ writel(mode->vdisplay, base + VID_VACTIVE_LINES);
+ writel(mode->hdisplay, base + VID_PKT_SIZE);
+
+ DRM_DEBUG_DRIVER("htot=%d, hfp=%d, hbp=%d, hsw=%d\n",
+ htot, hfp, hbp, hsw);
+ DRM_DEBUG_DRIVER("vtol=%d, vfp=%d, vbp=%d, vsw=%d\n",
+ vtot, vfp, vbp, vsw);
+ DRM_DEBUG_DRIVER("hsa_time=%d, hbp_time=%d, hline_time=%d\n",
+ hsa_time, hbp_time, hline_time);
+}
+
+static void dsi_set_video_mode(void __iomem *base, unsigned long flags)
+{
+ u32 val;
+ u32 mode_mask = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+ u32 non_burst_sync_pulse = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+ u32 non_burst_sync_event = MIPI_DSI_MODE_VIDEO;
+
+ /*
+ * choose video mode type
+ */
+ if ((flags & mode_mask) == non_burst_sync_pulse)
+ val = DSI_NON_BURST_SYNC_PULSES;
+ else if ((flags & mode_mask) == non_burst_sync_event)
+ val = DSI_NON_BURST_SYNC_EVENTS;
+ else
+ val = DSI_BURST_SYNC_PULSES_1;
+ writel(val, base + VID_MODE_CFG);
+
+ writel(PHY_TXREQUESTCLKHS, base + LPCLK_CTRL);
+ writel(DSI_VIDEO_MODE, base + MODE_CFG);
+}
+
+static void dsi_mipi_init(struct dw_dsi *dsi)
+{
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ struct mipi_phy_params *phy = &dsi->phy;
+ struct drm_display_mode *mode = &dsi->cur_mode;
+ u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+ void __iomem *base = ctx->base;
+ u32 dphy_req_kHz;
+
+ /*
+ * count phy params
+ */
+ dphy_req_kHz = mode->clock * bpp / dsi->lanes;
+ dsi_get_phy_params(dphy_req_kHz, phy);
+
+ /* reset Core */
+ writel(RESET, base + PWR_UP);
+
+ /* set dsi phy params */
+ dsi_set_mipi_phy(base, phy, dsi->lanes);
+
+ /* set dsi mode timing */
+ dsi_set_mode_timing(base, phy->lane_byte_clk_kHz, mode, dsi->format);
+
+ /* set dsi video mode */
+ dsi_set_video_mode(base, dsi->mode_flags);
+
+ /* dsi wake up */
+ writel(POWERUP, base + PWR_UP);
+
+ DRM_DEBUG_DRIVER("lanes=%d, pixel_clk=%d kHz, bytes_freq=%d kHz\n",
+ dsi->lanes, mode->clock, phy->lane_byte_clk_kHz);
+}
+
+static void dsi_encoder_disable(struct drm_encoder *encoder)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ void __iomem *base = ctx->base;
+
+ if (!dsi->enable)
+ return;
+
+ writel(0, base + PWR_UP);
+ writel(0, base + LPCLK_CTRL);
+ writel(0, base + PHY_RSTZ);
+ clk_disable_unprepare(ctx->pclk);
+
+ dsi->enable = false;
+}
+
+static void dsi_encoder_enable(struct drm_encoder *encoder)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ int ret;
+
+ if (dsi->enable)
+ return;
+
+ ret = clk_prepare_enable(ctx->pclk);
+ if (ret) {
+ DRM_ERROR("fail to enable pclk: %d\n", ret);
+ return;
+ }
+
+ dsi_mipi_init(dsi);
+
+ dsi->enable = true;
+}
+
+static void dsi_encoder_mode_set(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+
+ drm_mode_copy(&dsi->cur_mode, adj_mode);
+}
+
+static int dsi_encoder_atomic_check(struct drm_encoder *encoder,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state)
+{
+ /* do nothing */
+ return 0;
+}
+
+static const struct drm_encoder_helper_funcs dw_encoder_helper_funcs = {
+ .atomic_check = dsi_encoder_atomic_check,
+ .mode_set = dsi_encoder_mode_set,
+ .enable = dsi_encoder_enable,
+ .disable = dsi_encoder_disable
+};
+
+static const struct drm_encoder_funcs dw_encoder_funcs = {
+ .destroy = drm_encoder_cleanup,
+};
+
+static int dw_drm_encoder_init(struct device *dev,
+ struct drm_device *drm_dev,
+ struct drm_encoder *encoder)
+{
+ int ret;
+ u32 crtc_mask = drm_of_find_possible_crtcs(drm_dev, dev->of_node);
+
+ if (!crtc_mask) {
+ DRM_ERROR("failed to find crtc mask\n");
+ return -EINVAL;
+ }
+
+ encoder->possible_crtcs = crtc_mask;
+ ret = drm_encoder_init(drm_dev, encoder, &dw_encoder_funcs,
+ DRM_MODE_ENCODER_DSI, NULL);
+ if (ret) {
+ DRM_ERROR("failed to init dsi encoder\n");
+ return ret;
+ }
+
+ drm_encoder_helper_add(encoder, &dw_encoder_helper_funcs);
+
+ return 0;
+}
+
+static int dsi_bind(struct device *dev, struct device *master, void *data)
+{
+ struct dsi_data *ddata = dev_get_drvdata(dev);
+ struct dw_dsi *dsi = &ddata->dsi;
+ struct drm_device *drm_dev = data;
+ int ret;
+
+ ret = dw_drm_encoder_init(dev, drm_dev, &dsi->encoder);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void dsi_unbind(struct device *dev, struct device *master, void *data)
+{
+ /* do nothing */
+}
+
+static const struct component_ops dsi_ops = {
+ .bind = dsi_bind,
+ .unbind = dsi_unbind,
+};
+
+static int dsi_parse_dt(struct platform_device *pdev, struct dw_dsi *dsi)
+{
+ struct dsi_hw_ctx *ctx = dsi->ctx;
+ struct resource *res;
+
+ ctx->pclk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(ctx->pclk)) {
+ DRM_ERROR("failed to get pclk clock\n");
+ return PTR_ERR(ctx->pclk);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ctx->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(ctx->base)) {
+ DRM_ERROR("failed to remap dsi io region\n");
+ return PTR_ERR(ctx->base);
+ }
+
+ return 0;
+}
+
+static int dsi_probe(struct platform_device *pdev)
+{
+ struct dsi_data *data;
+ struct dw_dsi *dsi;
+ struct dsi_hw_ctx *ctx;
+ int ret;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data) {
+ DRM_ERROR("failed to allocate dsi data.\n");
+ return -ENOMEM;
+ }
+ dsi = &data->dsi;
+ ctx = &data->ctx;
+ dsi->ctx = ctx;
+
+ ret = dsi_parse_dt(pdev, dsi);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, data);
+
+ return component_add(&pdev->dev, &dsi_ops);
+}
+
+static int dsi_remove(struct platform_device *pdev)
+{
+ component_del(&pdev->dev, &dsi_ops);
+
+ return 0;
+}
+
+static const struct of_device_id dsi_of_match[] = {
+ {.compatible = "hisilicon,hi6220-dsi"},
+ { }
+};
+MODULE_DEVICE_TABLE(of, dsi_of_match);
+
+static struct platform_driver dsi_driver = {
+ .probe = dsi_probe,
+ .remove = dsi_remove,
+ .driver = {
+ .name = "dw-dsi",
+ .of_match_table = dsi_of_match,
+ },
+};
+
+module_platform_driver(dsi_driver);
+
+MODULE_AUTHOR("Xinliang Liu <xinliang.liu@linaro.org>");
+MODULE_AUTHOR("Xinliang Liu <z.liuxinliang@hisilicon.com>");
+MODULE_AUTHOR("Xinwei Kong <kong.kongxinwei@hisilicon.com>");
+MODULE_DESCRIPTION("DesignWare MIPI DSI Host Controller v1.02 driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h b/drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
new file mode 100644
index 000000000000..18808fc9f362
--- /dev/null
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
@@ -0,0 +1,103 @@
+/*
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2014-2016 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __DW_DSI_REG_H__
+#define __DW_DSI_REG_H__
+
+#define MASK(x) (BIT(x) - 1)
+
+/*
+ * regs
+ */
+#define PWR_UP 0x04 /* Core power-up */
+#define RESET 0
+#define POWERUP BIT(0)
+#define PHY_IF_CFG 0xA4 /* D-PHY interface configuration */
+#define CLKMGR_CFG 0x08 /* the internal clock dividers */
+#define PHY_RSTZ 0xA0 /* D-PHY reset control */
+#define PHY_ENABLECLK BIT(2)
+#define PHY_UNRSTZ BIT(1)
+#define PHY_UNSHUTDOWNZ BIT(0)
+#define PHY_TST_CTRL0 0xB4 /* D-PHY test interface control 0 */
+#define PHY_TST_CTRL1 0xB8 /* D-PHY test interface control 1 */
+#define CLK_TLPX 0x10
+#define CLK_THS_PREPARE 0x11
+#define CLK_THS_ZERO 0x12
+#define CLK_THS_TRAIL 0x13
+#define CLK_TWAKEUP 0x14
+#define DATA_TLPX(x) (0x20 + ((x) << 4))
+#define DATA_THS_PREPARE(x) (0x21 + ((x) << 4))
+#define DATA_THS_ZERO(x) (0x22 + ((x) << 4))
+#define DATA_THS_TRAIL(x) (0x23 + ((x) << 4))
+#define DATA_TTA_GO(x) (0x24 + ((x) << 4))
+#define DATA_TTA_GET(x) (0x25 + ((x) << 4))
+#define DATA_TWAKEUP(x) (0x26 + ((x) << 4))
+#define PHY_CFG_I 0x60
+#define PHY_CFG_PLL_I 0x63
+#define PHY_CFG_PLL_II 0x64
+#define PHY_CFG_PLL_III 0x65
+#define PHY_CFG_PLL_IV 0x66
+#define PHY_CFG_PLL_V 0x67
+#define DPI_COLOR_CODING 0x10 /* DPI color coding */
+#define DPI_CFG_POL 0x14 /* DPI polarity configuration */
+#define VID_HSA_TIME 0x48 /* Horizontal Sync Active time */
+#define VID_HBP_TIME 0x4C /* Horizontal Back Porch time */
+#define VID_HLINE_TIME 0x50 /* Line time */
+#define VID_VSA_LINES 0x54 /* Vertical Sync Active period */
+#define VID_VBP_LINES 0x58 /* Vertical Back Porch period */
+#define VID_VFP_LINES 0x5C /* Vertical Front Porch period */
+#define VID_VACTIVE_LINES 0x60 /* Vertical resolution */
+#define VID_PKT_SIZE 0x3C /* Video packet size */
+#define VID_MODE_CFG 0x38 /* Video mode configuration */
+#define PHY_TMR_CFG 0x9C /* Data lanes timing configuration */
+#define BTA_TO_CNT 0x8C /* Response timeout definition */
+#define PHY_TMR_LPCLK_CFG 0x98 /* clock lane timing configuration */
+#define CLK_DATA_TMR_CFG 0xCC
+#define LPCLK_CTRL 0x94 /* Low-power in clock lane */
+#define PHY_TXREQUESTCLKHS BIT(0)
+#define MODE_CFG 0x34 /* Video or Command mode selection */
+#define PHY_STATUS 0xB0 /* D-PHY PPI status interface */
+
+#define PHY_STOP_WAIT_TIME 0x30
+
+/*
+ * regs relevant enum
+ */
+enum dpi_color_coding {
+ DSI_24BITS_1 = 5,
+};
+
+enum dsi_video_mode_type {
+ DSI_NON_BURST_SYNC_PULSES = 0,
+ DSI_NON_BURST_SYNC_EVENTS,
+ DSI_BURST_SYNC_PULSES_1,
+ DSI_BURST_SYNC_PULSES_2
+};
+
+enum dsi_work_mode {
+ DSI_VIDEO_MODE = 0,
+ DSI_COMMAND_MODE
+};
+
+/*
+ * Register Write/Read Helper functions
+ */
+static inline void dw_update_bits(void __iomem *addr, u32 bit_start,
+ u32 mask, u32 val)
+{
+ u32 tmp, orig;
+
+ orig = readl(addr);
+ tmp = orig & ~(mask << bit_start);
+ tmp |= (val & mask) << bit_start;
+ writel(tmp, addr);
+}
+
+#endif /* __DW_DRM_DSI_H__ */
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 08/10] drm/hisilicon: Add designware dsi host driver
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add DesignWare dsi host driver for hi6220 SoC.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3: None.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
---
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 50 ++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
index 1a930b77ec53..ea7711832959 100644
--- a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
@@ -80,6 +80,7 @@ struct dsi_hw_ctx {
struct dw_dsi {
struct drm_encoder encoder;
+ struct mipi_dsi_host host;
struct drm_display_mode cur_mode;
struct dsi_hw_ctx *ctx;
struct mipi_phy_params phy;
@@ -654,6 +655,51 @@ static int dw_drm_encoder_init(struct device *dev,
return 0;
}
+static int dsi_host_attach(struct mipi_dsi_host *host,
+ struct mipi_dsi_device *mdsi)
+{
+ struct dw_dsi *dsi = host_to_dsi(host);
+
+ if (mdsi->lanes < 1 || mdsi->lanes > 4) {
+ DRM_ERROR("dsi device params invalid\n");
+ return -EINVAL;
+ }
+
+ dsi->lanes = mdsi->lanes;
+ dsi->format = mdsi->format;
+ dsi->mode_flags = mdsi->mode_flags;
+
+ return 0;
+}
+
+static int dsi_host_detach(struct mipi_dsi_host *host,
+ struct mipi_dsi_device *mdsi)
+{
+ /* do nothing */
+ return 0;
+}
+
+static const struct mipi_dsi_host_ops dsi_host_ops = {
+ .attach = dsi_host_attach,
+ .detach = dsi_host_detach,
+};
+
+static int dsi_host_init(struct device *dev, struct dw_dsi *dsi)
+{
+ struct mipi_dsi_host *host = &dsi->host;
+ int ret;
+
+ host->dev = dev;
+ host->ops = &dsi_host_ops;
+ ret = mipi_dsi_host_register(host);
+ if (ret) {
+ DRM_ERROR("failed to register dsi host\n");
+ return ret;
+ }
+
+ return 0;
+}
+
static int dsi_bind(struct device *dev, struct device *master, void *data)
{
struct dsi_data *ddata = dev_get_drvdata(dev);
@@ -665,6 +711,10 @@ static int dsi_bind(struct device *dev, struct device *master, void *data)
if (ret)
return ret;
+ ret = dsi_host_init(dev, dsi);
+ if (ret)
+ return ret;
+
return 0;
}
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 08/10] drm/hisilicon: Add designware dsi host driver
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add DesignWare dsi host driver for hi6220 SoC.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3: None.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
---
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 50 ++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
index 1a930b77ec53..ea7711832959 100644
--- a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
@@ -80,6 +80,7 @@ struct dsi_hw_ctx {
struct dw_dsi {
struct drm_encoder encoder;
+ struct mipi_dsi_host host;
struct drm_display_mode cur_mode;
struct dsi_hw_ctx *ctx;
struct mipi_phy_params phy;
@@ -654,6 +655,51 @@ static int dw_drm_encoder_init(struct device *dev,
return 0;
}
+static int dsi_host_attach(struct mipi_dsi_host *host,
+ struct mipi_dsi_device *mdsi)
+{
+ struct dw_dsi *dsi = host_to_dsi(host);
+
+ if (mdsi->lanes < 1 || mdsi->lanes > 4) {
+ DRM_ERROR("dsi device params invalid\n");
+ return -EINVAL;
+ }
+
+ dsi->lanes = mdsi->lanes;
+ dsi->format = mdsi->format;
+ dsi->mode_flags = mdsi->mode_flags;
+
+ return 0;
+}
+
+static int dsi_host_detach(struct mipi_dsi_host *host,
+ struct mipi_dsi_device *mdsi)
+{
+ /* do nothing */
+ return 0;
+}
+
+static const struct mipi_dsi_host_ops dsi_host_ops = {
+ .attach = dsi_host_attach,
+ .detach = dsi_host_detach,
+};
+
+static int dsi_host_init(struct device *dev, struct dw_dsi *dsi)
+{
+ struct mipi_dsi_host *host = &dsi->host;
+ int ret;
+
+ host->dev = dev;
+ host->ops = &dsi_host_ops;
+ ret = mipi_dsi_host_register(host);
+ if (ret) {
+ DRM_ERROR("failed to register dsi host\n");
+ return ret;
+ }
+
+ return 0;
+}
+
static int dsi_bind(struct device *dev, struct device *master, void *data)
{
struct dsi_data *ddata = dev_get_drvdata(dev);
@@ -665,6 +711,10 @@ static int dsi_bind(struct device *dev, struct device *master, void *data)
if (ret)
return ret;
+ ret = dsi_host_init(dev, dsi);
+ if (ret)
+ return ret;
+
return 0;
}
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 09/10] drm/hisilicon: Add support for external bridge
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add support for external HDMI bridge.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3:
- Fix a typo: s/exteranl/external.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
---
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 52 ++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
index ea7711832959..bfbc2159250d 100644
--- a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
@@ -80,6 +80,7 @@ struct dsi_hw_ctx {
struct dw_dsi {
struct drm_encoder encoder;
+ struct drm_bridge *bridge;
struct mipi_dsi_host host;
struct drm_display_mode cur_mode;
struct dsi_hw_ctx *ctx;
@@ -700,6 +701,25 @@ static int dsi_host_init(struct device *dev, struct dw_dsi *dsi)
return 0;
}
+static int dsi_bridge_init(struct drm_device *dev, struct dw_dsi *dsi)
+{
+ struct drm_encoder *encoder = &dsi->encoder;
+ struct drm_bridge *bridge = dsi->bridge;
+ int ret;
+
+ /* associate the bridge to dsi encoder */
+ encoder->bridge = bridge;
+ bridge->encoder = encoder;
+
+ ret = drm_bridge_attach(dev, bridge);
+ if (ret) {
+ DRM_ERROR("failed to attach external bridge\n");
+ return ret;
+ }
+
+ return 0;
+}
+
static int dsi_bind(struct device *dev, struct device *master, void *data)
{
struct dsi_data *ddata = dev_get_drvdata(dev);
@@ -715,6 +735,10 @@ static int dsi_bind(struct device *dev, struct device *master, void *data)
if (ret)
return ret;
+ ret = dsi_bridge_init(drm_dev, dsi);
+ if (ret)
+ return ret;
+
return 0;
}
@@ -731,8 +755,36 @@ static const struct component_ops dsi_ops = {
static int dsi_parse_dt(struct platform_device *pdev, struct dw_dsi *dsi)
{
struct dsi_hw_ctx *ctx = dsi->ctx;
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *endpoint, *bridge_node;
+ struct drm_bridge *bridge;
struct resource *res;
+ /*
+ * Get the endpoint node. In our case, dsi has one output port1
+ * to which the external HDMI bridge is connected.
+ */
+ endpoint = of_graph_get_endpoint_by_regs(np, 1, -1);
+ if (!endpoint) {
+ DRM_ERROR("no valid endpoint node\n");
+ return -ENODEV;
+ }
+ of_node_put(endpoint);
+
+ bridge_node = of_graph_get_remote_port_parent(endpoint);
+ if (!bridge_node) {
+ DRM_ERROR("no valid bridge node\n");
+ return -ENODEV;
+ }
+ of_node_put(bridge_node);
+
+ bridge = of_drm_find_bridge(bridge_node);
+ if (!bridge) {
+ DRM_INFO("wait for external HDMI bridge driver.\n");
+ return -EPROBE_DEFER;
+ }
+ dsi->bridge = bridge;
+
ctx->pclk = devm_clk_get(&pdev->dev, "pclk");
if (IS_ERR(ctx->pclk)) {
DRM_ERROR("failed to get pclk clock\n");
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 09/10] drm/hisilicon: Add support for external bridge
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add support for external HDMI bridge.
v8: None.
v7: None.
v6: None.
v5: None.
v4: None.
v3:
- Fix a typo: s/exteranl/external.
v2:
- Remove abtraction layer.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
---
drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 52 ++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
index ea7711832959..bfbc2159250d 100644
--- a/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
+++ b/drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
@@ -80,6 +80,7 @@ struct dsi_hw_ctx {
struct dw_dsi {
struct drm_encoder encoder;
+ struct drm_bridge *bridge;
struct mipi_dsi_host host;
struct drm_display_mode cur_mode;
struct dsi_hw_ctx *ctx;
@@ -700,6 +701,25 @@ static int dsi_host_init(struct device *dev, struct dw_dsi *dsi)
return 0;
}
+static int dsi_bridge_init(struct drm_device *dev, struct dw_dsi *dsi)
+{
+ struct drm_encoder *encoder = &dsi->encoder;
+ struct drm_bridge *bridge = dsi->bridge;
+ int ret;
+
+ /* associate the bridge to dsi encoder */
+ encoder->bridge = bridge;
+ bridge->encoder = encoder;
+
+ ret = drm_bridge_attach(dev, bridge);
+ if (ret) {
+ DRM_ERROR("failed to attach external bridge\n");
+ return ret;
+ }
+
+ return 0;
+}
+
static int dsi_bind(struct device *dev, struct device *master, void *data)
{
struct dsi_data *ddata = dev_get_drvdata(dev);
@@ -715,6 +735,10 @@ static int dsi_bind(struct device *dev, struct device *master, void *data)
if (ret)
return ret;
+ ret = dsi_bridge_init(drm_dev, dsi);
+ if (ret)
+ return ret;
+
return 0;
}
@@ -731,8 +755,36 @@ static const struct component_ops dsi_ops = {
static int dsi_parse_dt(struct platform_device *pdev, struct dw_dsi *dsi)
{
struct dsi_hw_ctx *ctx = dsi->ctx;
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *endpoint, *bridge_node;
+ struct drm_bridge *bridge;
struct resource *res;
+ /*
+ * Get the endpoint node. In our case, dsi has one output port1
+ * to which the external HDMI bridge is connected.
+ */
+ endpoint = of_graph_get_endpoint_by_regs(np, 1, -1);
+ if (!endpoint) {
+ DRM_ERROR("no valid endpoint node\n");
+ return -ENODEV;
+ }
+ of_node_put(endpoint);
+
+ bridge_node = of_graph_get_remote_port_parent(endpoint);
+ if (!bridge_node) {
+ DRM_ERROR("no valid bridge node\n");
+ return -ENODEV;
+ }
+ of_node_put(bridge_node);
+
+ bridge = of_drm_find_bridge(bridge_node);
+ if (!bridge) {
+ DRM_INFO("wait for external HDMI bridge driver.\n");
+ return -EPROBE_DEFER;
+ }
+ dsi->bridge = bridge;
+
ctx->pclk = devm_clk_get(&pdev->dev, "pclk");
if (IS_ERR(ctx->pclk)) {
DRM_ERROR("failed to get pclk clock\n");
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-11 8:55 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland
Cc: linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu, Xinliang Liu
Add maintainer and reviewer for hisilicon DRM driver.
v8: None.
v7: None.
v6: None.
v5: None.
v4:
- Add Chen Feng <puck.chen@hisilicon.com> as Designated reviewer.
v3: First version.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
---
MAINTAINERS | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 61a323a6b2cf..a2ef58860689 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3840,6 +3840,16 @@ S: Maintained
F: drivers/gpu/drm/gma500
F: include/drm/gma500*
+DRM DRIVERS FOR HISILICON
+M: Xinliang Liu <z.liuxinliang@hisilicon.com>
+R: Xinwei Kong <kong.kongxinwei@hisilicon.com>
+R: Chen Feng <puck.chen@hisilicon.com>
+L: dri-devel@lists.freedesktop.org
+T: git git://github.com/xin3liang/linux.git
+S: Maintained
+F: drivers/gpu/drm/hisilicon
+F: Documentation/devicetree/bindings/display/hisilicon
+
DRM DRIVERS FOR NVIDIA TEGRA
M: Thierry Reding <thierry.reding@gmail.com>
M: Terje Bergström <tbergstrom@nvidia.com>
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver
@ 2016-04-11 8:55 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-11 8:55 UTC (permalink / raw)
To: linux-arm-kernel
Add maintainer and reviewer for hisilicon DRM driver.
v8: None.
v7: None.
v6: None.
v5: None.
v4:
- Add Chen Feng <puck.chen@hisilicon.com> as Designated reviewer.
v3: First version.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
---
MAINTAINERS | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 61a323a6b2cf..a2ef58860689 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3840,6 +3840,16 @@ S: Maintained
F: drivers/gpu/drm/gma500
F: include/drm/gma500*
+DRM DRIVERS FOR HISILICON
+M: Xinliang Liu <z.liuxinliang@hisilicon.com>
+R: Xinwei Kong <kong.kongxinwei@hisilicon.com>
+R: Chen Feng <puck.chen@hisilicon.com>
+L: dri-devel at lists.freedesktop.org
+T: git git://github.com/xin3liang/linux.git
+S: Maintained
+F: drivers/gpu/drm/hisilicon
+F: Documentation/devicetree/bindings/display/hisilicon
+
DRM DRIVERS FOR NVIDIA TEGRA
M: Thierry Reding <thierry.reding@gmail.com>
M: Terje Bergstr?m <tbergstrom@nvidia.com>
--
2.8.0
^ permalink raw reply related [flat|nested] 36+ messages in thread
* Re: [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-12 16:08 ` Daniel Vetter
-1 siblings, 0 replies; 36+ messages in thread
From: Daniel Vetter @ 2016-04-12 16:08 UTC (permalink / raw)
To: Xinliang Liu
Cc: dri-devel, devicetree, daniel, robh, daniel, architt, airlied,
corbet, catalin.marinas, will.deacon, emil.l.velikov,
mark.rutland, linux-doc, linux-arm-kernel, linuxarm, andy.green,
haojian.zhuang, liguozhu, xuwei5, w.f, puck.chen, bintian.wang,
benjamin.gaignard, xuyiping, kong.kongxinwei, zourongrong,
lijianhua, sumit.semwal, guodong.xu
On Mon, Apr 11, 2016 at 04:55:33PM +0800, Xinliang Liu wrote:
> This patch set adds a new drm driver for HiSilicon Kirin hi6220 SoC.
> Current testing and support board is Hikey board which is one of Linaro
> 96boards. It is an arm64 open source board. For more information about
> this board, please access https://www.96boards.org.
>
> Hardware Detail
> ---------------
> The display subsystem of Hi6220 SoC is shown as bellow:
> +-----+ +----------+ +-----+ +-------------+
> | | | | | | | |
> | FB |------>| ADE |---->| DSI |---->| External |
> | | | | | | | HDMI/panel |
> +-----+ +----------+ +-----+ +-------------+
>
> - ADE(Advanced Display Engine) is the display controller. It contains 7
> channels, 3 overlay compositors and a LDI.
> - A channel looks like: DMA-->clip-->scale-->ctrans(or called csc).
> - Overlay compositor is response to compose planes which come from 7
> channels and pass composed image to LDI.
> - LDI is response to generate timings and RGB data stream.
> - DSI converts the RGB data stream from ADE to DSI packets.
> - External HDMI/panel module is connected with DSI bus. Now Hikey use a
> ADI's ADV7533 external HDMI chip.
I haven't looked at the details again, but seems it's all ready. Please
create a pull request for the entire pile against drm-next and submit it
to Dave Airlie.
Thanks, Daniel
>
> Change History
> -------------
> Changes in v8:
> - Rebase to v4.6-rc3
>
> Changes in v7:
> - Add config.mutex protection when accessing mode_config.connector_list.
> - Clean up match data getting of kirin_drm_drv.c.
> - A few Regs define clean up and typo fixs for ADE crtc and DSI encoder
> driver.
> - Fix vblank irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
>
> Changes in v6:
> - Cleanup values part of reg and clocks relevant properties.
> - Change "pclk_dsi" clock name to "pclk".
>
> Changes in v5:
> - Remove endpoint unit address of dsi output port.
> - Use syscon to access ADE media NOC QoS registers instread of directly
> writing registers.
> - Use reset controller to reset ADE instead of directly writing registers.
>
> Changes in v4:
> - Describe more specific of clocks and ports of binding docs.
> - Fix indentation of binding docs.
>
> Changes in v3:
> - Move and rename all the files to kirin sub-directory.
> So that we could separate different seires SoCs' driver.
> - Make ade as the drm master node.
> - Replace drm_platform_init, load, unload implementation.
> - Use assigned-clocks to set clock rate.
> - Use ports to connect display relevant nodes.
> - Rename hisi_drm_dsi.c to dw_drm_dsi.c
> - Make encoder type as DRM_MODE_ENCODER_DSI.
> - A few cleanup on regs and code.
>
> Changes in v2:
> - Remove abtraction layer of plane/crtc/encoder/connector.
> - Refactor atomic implementation according to Daniel Vetter's guides:
> http://blog.ffwll.ch/2014/11/atomic-modeset-support-for-kms-drivers.html
> http://blog.ffwll.ch/2015/09/xdc-2015-atomic-modesetting-for-drivers.html
> http://blog.ffwll.ch/2015/08/atomic-modesetting-design-overview.html
> - Use bridge instead of slave encoder to connect external HDMI.
> - Move dt binding docs to bindings/display/hisilicon directory.
>
> Xinliang Liu (10):
> drm/hisilicon: Add device tree binding for hi6220 display subsystem
> drm/hisilicon: Add hisilicon kirin drm master driver
> drm/hisilicon: Add crtc driver for ADE
> drm/hisilicon: Add plane driver for ADE
> drm/hisilicon: Add vblank driver for ADE
> drm/hisilicon: Add cma fbdev and hotplug
> drm/hisilicon: Add designware dsi encoder driver
> drm/hisilicon: Add designware dsi host driver
> drm/hisilicon: Add support for external bridge
> MAINTAINERS: Add maintainer for hisilicon DRM driver
>
> .../bindings/display/hisilicon/dw-dsi.txt | 72 ++
> .../bindings/display/hisilicon/hisi-ade.txt | 64 ++
> MAINTAINERS | 10 +
> drivers/gpu/drm/Kconfig | 2 +
> drivers/gpu/drm/Makefile | 1 +
> drivers/gpu/drm/hisilicon/Kconfig | 5 +
> drivers/gpu/drm/hisilicon/Makefile | 5 +
> drivers/gpu/drm/hisilicon/kirin/Kconfig | 10 +
> drivers/gpu/drm/hisilicon/kirin/Makefile | 5 +
> drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 857 ++++++++++++++++
> drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++
> drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 +++++
> drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 1057 ++++++++++++++++++++
> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 367 +++++++
> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 31 +
> 15 files changed, 2819 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
> create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
> create mode 100644 drivers/gpu/drm/hisilicon/Makefile
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
>
> --
> 2.8.0
>
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC
@ 2016-04-12 16:08 ` Daniel Vetter
0 siblings, 0 replies; 36+ messages in thread
From: Daniel Vetter @ 2016-04-12 16:08 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Apr 11, 2016 at 04:55:33PM +0800, Xinliang Liu wrote:
> This patch set adds a new drm driver for HiSilicon Kirin hi6220 SoC.
> Current testing and support board is Hikey board which is one of Linaro
> 96boards. It is an arm64 open source board. For more information about
> this board, please access https://www.96boards.org.
>
> Hardware Detail
> ---------------
> The display subsystem of Hi6220 SoC is shown as bellow:
> +-----+ +----------+ +-----+ +-------------+
> | | | | | | | |
> | FB |------>| ADE |---->| DSI |---->| External |
> | | | | | | | HDMI/panel |
> +-----+ +----------+ +-----+ +-------------+
>
> - ADE(Advanced Display Engine) is the display controller. It contains 7
> channels, 3 overlay compositors and a LDI.
> - A channel looks like: DMA-->clip-->scale-->ctrans(or called csc).
> - Overlay compositor is response to compose planes which come from 7
> channels and pass composed image to LDI.
> - LDI is response to generate timings and RGB data stream.
> - DSI converts the RGB data stream from ADE to DSI packets.
> - External HDMI/panel module is connected with DSI bus. Now Hikey use a
> ADI's ADV7533 external HDMI chip.
I haven't looked at the details again, but seems it's all ready. Please
create a pull request for the entire pile against drm-next and submit it
to Dave Airlie.
Thanks, Daniel
>
> Change History
> -------------
> Changes in v8:
> - Rebase to v4.6-rc3
>
> Changes in v7:
> - Add config.mutex protection when accessing mode_config.connector_list.
> - Clean up match data getting of kirin_drm_drv.c.
> - A few Regs define clean up and typo fixs for ADE crtc and DSI encoder
> driver.
> - Fix vblank irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
>
> Changes in v6:
> - Cleanup values part of reg and clocks relevant properties.
> - Change "pclk_dsi" clock name to "pclk".
>
> Changes in v5:
> - Remove endpoint unit address of dsi output port.
> - Use syscon to access ADE media NOC QoS registers instread of directly
> writing registers.
> - Use reset controller to reset ADE instead of directly writing registers.
>
> Changes in v4:
> - Describe more specific of clocks and ports of binding docs.
> - Fix indentation of binding docs.
>
> Changes in v3:
> - Move and rename all the files to kirin sub-directory.
> So that we could separate different seires SoCs' driver.
> - Make ade as the drm master node.
> - Replace drm_platform_init, load, unload implementation.
> - Use assigned-clocks to set clock rate.
> - Use ports to connect display relevant nodes.
> - Rename hisi_drm_dsi.c to dw_drm_dsi.c
> - Make encoder type as DRM_MODE_ENCODER_DSI.
> - A few cleanup on regs and code.
>
> Changes in v2:
> - Remove abtraction layer of plane/crtc/encoder/connector.
> - Refactor atomic implementation according to Daniel Vetter's guides:
> http://blog.ffwll.ch/2014/11/atomic-modeset-support-for-kms-drivers.html
> http://blog.ffwll.ch/2015/09/xdc-2015-atomic-modesetting-for-drivers.html
> http://blog.ffwll.ch/2015/08/atomic-modesetting-design-overview.html
> - Use bridge instead of slave encoder to connect external HDMI.
> - Move dt binding docs to bindings/display/hisilicon directory.
>
> Xinliang Liu (10):
> drm/hisilicon: Add device tree binding for hi6220 display subsystem
> drm/hisilicon: Add hisilicon kirin drm master driver
> drm/hisilicon: Add crtc driver for ADE
> drm/hisilicon: Add plane driver for ADE
> drm/hisilicon: Add vblank driver for ADE
> drm/hisilicon: Add cma fbdev and hotplug
> drm/hisilicon: Add designware dsi encoder driver
> drm/hisilicon: Add designware dsi host driver
> drm/hisilicon: Add support for external bridge
> MAINTAINERS: Add maintainer for hisilicon DRM driver
>
> .../bindings/display/hisilicon/dw-dsi.txt | 72 ++
> .../bindings/display/hisilicon/hisi-ade.txt | 64 ++
> MAINTAINERS | 10 +
> drivers/gpu/drm/Kconfig | 2 +
> drivers/gpu/drm/Makefile | 1 +
> drivers/gpu/drm/hisilicon/Kconfig | 5 +
> drivers/gpu/drm/hisilicon/Makefile | 5 +
> drivers/gpu/drm/hisilicon/kirin/Kconfig | 10 +
> drivers/gpu/drm/hisilicon/kirin/Makefile | 5 +
> drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 857 ++++++++++++++++
> drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++
> drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 +++++
> drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 1057 ++++++++++++++++++++
> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 367 +++++++
> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 31 +
> 15 files changed, 2819 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
> create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
> create mode 100644 drivers/gpu/drm/hisilicon/Makefile
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
>
> --
> 2.8.0
>
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC
2016-04-12 16:08 ` Daniel Vetter
@ 2016-04-13 1:12 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-13 1:12 UTC (permalink / raw)
To: Daniel Vetter
Cc: dri-devel, devicetree, Rob Herring, Daniel Stone, Archit Taneja,
David Airlie, Jon Corbet, Catalin Marinas, Will Deacon,
Emil Velikov, Mark Rutland, linux-doc, LAKML, Linuxarm,
Andy Green, Haojian Zhuang, Liguozhu (Kenneth),
Xu Wei, Wang Fei, Feng Chen, Bintian Wang, Benjamin Gaignard,
Yiping Xu, XinWei Kong
On 13 April 2016 at 00:08, Daniel Vetter <daniel@ffwll.ch> wrote:
> On Mon, Apr 11, 2016 at 04:55:33PM +0800, Xinliang Liu wrote:
>> This patch set adds a new drm driver for HiSilicon Kirin hi6220 SoC.
>> Current testing and support board is Hikey board which is one of Linaro
>> 96boards. It is an arm64 open source board. For more information about
>> this board, please access https://www.96boards.org.
>>
>> Hardware Detail
>> ---------------
>> The display subsystem of Hi6220 SoC is shown as bellow:
>> +-----+ +----------+ +-----+ +-------------+
>> | | | | | | | |
>> | FB |------>| ADE |---->| DSI |---->| External |
>> | | | | | | | HDMI/panel |
>> +-----+ +----------+ +-----+ +-------------+
>>
>> - ADE(Advanced Display Engine) is the display controller. It contains 7
>> channels, 3 overlay compositors and a LDI.
>> - A channel looks like: DMA-->clip-->scale-->ctrans(or called csc).
>> - Overlay compositor is response to compose planes which come from 7
>> channels and pass composed image to LDI.
>> - LDI is response to generate timings and RGB data stream.
>> - DSI converts the RGB data stream from ADE to DSI packets.
>> - External HDMI/panel module is connected with DSI bus. Now Hikey use a
>> ADI's ADV7533 external HDMI chip.
>
> I haven't looked at the details again, but seems it's all ready. Please
> create a pull request for the entire pile against drm-next and submit it
> to Dave Airlie.
Thanks Daniel, will send pull request to Dave soon.
Best,
-xinliang
>
> Thanks, Daniel
>
>>
>> Change History
>> -------------
>> Changes in v8:
>> - Rebase to v4.6-rc3
>>
>> Changes in v7:
>> - Add config.mutex protection when accessing mode_config.connector_list.
>> - Clean up match data getting of kirin_drm_drv.c.
>> - A few Regs define clean up and typo fixs for ADE crtc and DSI encoder
>> driver.
>> - Fix vblank irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
>>
>> Changes in v6:
>> - Cleanup values part of reg and clocks relevant properties.
>> - Change "pclk_dsi" clock name to "pclk".
>>
>> Changes in v5:
>> - Remove endpoint unit address of dsi output port.
>> - Use syscon to access ADE media NOC QoS registers instread of directly
>> writing registers.
>> - Use reset controller to reset ADE instead of directly writing registers.
>>
>> Changes in v4:
>> - Describe more specific of clocks and ports of binding docs.
>> - Fix indentation of binding docs.
>>
>> Changes in v3:
>> - Move and rename all the files to kirin sub-directory.
>> So that we could separate different seires SoCs' driver.
>> - Make ade as the drm master node.
>> - Replace drm_platform_init, load, unload implementation.
>> - Use assigned-clocks to set clock rate.
>> - Use ports to connect display relevant nodes.
>> - Rename hisi_drm_dsi.c to dw_drm_dsi.c
>> - Make encoder type as DRM_MODE_ENCODER_DSI.
>> - A few cleanup on regs and code.
>>
>> Changes in v2:
>> - Remove abtraction layer of plane/crtc/encoder/connector.
>> - Refactor atomic implementation according to Daniel Vetter's guides:
>> http://blog.ffwll.ch/2014/11/atomic-modeset-support-for-kms-drivers.html
>> http://blog.ffwll.ch/2015/09/xdc-2015-atomic-modesetting-for-drivers.html
>> http://blog.ffwll.ch/2015/08/atomic-modesetting-design-overview.html
>> - Use bridge instead of slave encoder to connect external HDMI.
>> - Move dt binding docs to bindings/display/hisilicon directory.
>>
>> Xinliang Liu (10):
>> drm/hisilicon: Add device tree binding for hi6220 display subsystem
>> drm/hisilicon: Add hisilicon kirin drm master driver
>> drm/hisilicon: Add crtc driver for ADE
>> drm/hisilicon: Add plane driver for ADE
>> drm/hisilicon: Add vblank driver for ADE
>> drm/hisilicon: Add cma fbdev and hotplug
>> drm/hisilicon: Add designware dsi encoder driver
>> drm/hisilicon: Add designware dsi host driver
>> drm/hisilicon: Add support for external bridge
>> MAINTAINERS: Add maintainer for hisilicon DRM driver
>>
>> .../bindings/display/hisilicon/dw-dsi.txt | 72 ++
>> .../bindings/display/hisilicon/hisi-ade.txt | 64 ++
>> MAINTAINERS | 10 +
>> drivers/gpu/drm/Kconfig | 2 +
>> drivers/gpu/drm/Makefile | 1 +
>> drivers/gpu/drm/hisilicon/Kconfig | 5 +
>> drivers/gpu/drm/hisilicon/Makefile | 5 +
>> drivers/gpu/drm/hisilicon/kirin/Kconfig | 10 +
>> drivers/gpu/drm/hisilicon/kirin/Makefile | 5 +
>> drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 857 ++++++++++++++++
>> drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++
>> drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 +++++
>> drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 1057 ++++++++++++++++++++
>> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 367 +++++++
>> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 31 +
>> 15 files changed, 2819 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
>> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
>> create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
>> create mode 100644 drivers/gpu/drm/hisilicon/Makefile
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
>>
>> --
>> 2.8.0
>>
>
> --
> Daniel Vetter
> Software Engineer, Intel Corporation
> http://blog.ffwll.ch
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC
@ 2016-04-13 1:12 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-13 1:12 UTC (permalink / raw)
To: linux-arm-kernel
On 13 April 2016 at 00:08, Daniel Vetter <daniel@ffwll.ch> wrote:
> On Mon, Apr 11, 2016 at 04:55:33PM +0800, Xinliang Liu wrote:
>> This patch set adds a new drm driver for HiSilicon Kirin hi6220 SoC.
>> Current testing and support board is Hikey board which is one of Linaro
>> 96boards. It is an arm64 open source board. For more information about
>> this board, please access https://www.96boards.org.
>>
>> Hardware Detail
>> ---------------
>> The display subsystem of Hi6220 SoC is shown as bellow:
>> +-----+ +----------+ +-----+ +-------------+
>> | | | | | | | |
>> | FB |------>| ADE |---->| DSI |---->| External |
>> | | | | | | | HDMI/panel |
>> +-----+ +----------+ +-----+ +-------------+
>>
>> - ADE(Advanced Display Engine) is the display controller. It contains 7
>> channels, 3 overlay compositors and a LDI.
>> - A channel looks like: DMA-->clip-->scale-->ctrans(or called csc).
>> - Overlay compositor is response to compose planes which come from 7
>> channels and pass composed image to LDI.
>> - LDI is response to generate timings and RGB data stream.
>> - DSI converts the RGB data stream from ADE to DSI packets.
>> - External HDMI/panel module is connected with DSI bus. Now Hikey use a
>> ADI's ADV7533 external HDMI chip.
>
> I haven't looked at the details again, but seems it's all ready. Please
> create a pull request for the entire pile against drm-next and submit it
> to Dave Airlie.
Thanks Daniel, will send pull request to Dave soon.
Best,
-xinliang
>
> Thanks, Daniel
>
>>
>> Change History
>> -------------
>> Changes in v8:
>> - Rebase to v4.6-rc3
>>
>> Changes in v7:
>> - Add config.mutex protection when accessing mode_config.connector_list.
>> - Clean up match data getting of kirin_drm_drv.c.
>> - A few Regs define clean up and typo fixs for ADE crtc and DSI encoder
>> driver.
>> - Fix vblank irq flag "DRIVER_IRQF_SHARED" to "IRQF_SHARED".
>>
>> Changes in v6:
>> - Cleanup values part of reg and clocks relevant properties.
>> - Change "pclk_dsi" clock name to "pclk".
>>
>> Changes in v5:
>> - Remove endpoint unit address of dsi output port.
>> - Use syscon to access ADE media NOC QoS registers instread of directly
>> writing registers.
>> - Use reset controller to reset ADE instead of directly writing registers.
>>
>> Changes in v4:
>> - Describe more specific of clocks and ports of binding docs.
>> - Fix indentation of binding docs.
>>
>> Changes in v3:
>> - Move and rename all the files to kirin sub-directory.
>> So that we could separate different seires SoCs' driver.
>> - Make ade as the drm master node.
>> - Replace drm_platform_init, load, unload implementation.
>> - Use assigned-clocks to set clock rate.
>> - Use ports to connect display relevant nodes.
>> - Rename hisi_drm_dsi.c to dw_drm_dsi.c
>> - Make encoder type as DRM_MODE_ENCODER_DSI.
>> - A few cleanup on regs and code.
>>
>> Changes in v2:
>> - Remove abtraction layer of plane/crtc/encoder/connector.
>> - Refactor atomic implementation according to Daniel Vetter's guides:
>> http://blog.ffwll.ch/2014/11/atomic-modeset-support-for-kms-drivers.html
>> http://blog.ffwll.ch/2015/09/xdc-2015-atomic-modesetting-for-drivers.html
>> http://blog.ffwll.ch/2015/08/atomic-modesetting-design-overview.html
>> - Use bridge instead of slave encoder to connect external HDMI.
>> - Move dt binding docs to bindings/display/hisilicon directory.
>>
>> Xinliang Liu (10):
>> drm/hisilicon: Add device tree binding for hi6220 display subsystem
>> drm/hisilicon: Add hisilicon kirin drm master driver
>> drm/hisilicon: Add crtc driver for ADE
>> drm/hisilicon: Add plane driver for ADE
>> drm/hisilicon: Add vblank driver for ADE
>> drm/hisilicon: Add cma fbdev and hotplug
>> drm/hisilicon: Add designware dsi encoder driver
>> drm/hisilicon: Add designware dsi host driver
>> drm/hisilicon: Add support for external bridge
>> MAINTAINERS: Add maintainer for hisilicon DRM driver
>>
>> .../bindings/display/hisilicon/dw-dsi.txt | 72 ++
>> .../bindings/display/hisilicon/hisi-ade.txt | 64 ++
>> MAINTAINERS | 10 +
>> drivers/gpu/drm/Kconfig | 2 +
>> drivers/gpu/drm/Makefile | 1 +
>> drivers/gpu/drm/hisilicon/Kconfig | 5 +
>> drivers/gpu/drm/hisilicon/Makefile | 5 +
>> drivers/gpu/drm/hisilicon/kirin/Kconfig | 10 +
>> drivers/gpu/drm/hisilicon/kirin/Makefile | 5 +
>> drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 857 ++++++++++++++++
>> drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h | 103 ++
>> drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h | 230 +++++
>> drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 1057 ++++++++++++++++++++
>> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c | 367 +++++++
>> drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h | 31 +
>> 15 files changed, 2819 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt
>> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
>> create mode 100644 drivers/gpu/drm/hisilicon/Kconfig
>> create mode 100644 drivers/gpu/drm/hisilicon/Makefile
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Kconfig
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/Makefile
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/dw_dsi_reg.h
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_ade_reg.h
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.c
>> create mode 100644 drivers/gpu/drm/hisilicon/kirin/kirin_drm_drv.h
>>
>> --
>> 2.8.0
>>
>
> --
> Daniel Vetter
> Software Engineer, Intel Corporation
> http://blog.ffwll.ch
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-13 11:54 ` Emil Velikov
-1 siblings, 0 replies; 36+ messages in thread
From: Emil Velikov @ 2016-04-13 11:54 UTC (permalink / raw)
To: Xinliang Liu
Cc: Mark Rutland, linux-doc, Catalin Marinas, Will Deacon, linuxarm,
ML dri-devel, xuwei5, Benjamin Gaignard, Rongrong Zou, xuyiping,
Jonathan Corbet, w.f, devicetree, bintian.wang, puck.chen, LAKML,
Andy Green, guodong.xu, liguozhu, Haojian Zhuang
Hi Xinliang,
On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
> Add maintainer and reviewer for hisilicon DRM driver.
>
> v8: None.
> v7: None.
> v6: None.
> v5: None.
> v4:
> - Add Chen Feng <puck.chen@hisilicon.com> as Designated reviewer.
> v3: First version.
>
> Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
> ---
> MAINTAINERS | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 61a323a6b2cf..a2ef58860689 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3840,6 +3840,16 @@ S: Maintained
> F: drivers/gpu/drm/gma500
> F: include/drm/gma500*
>
> +DRM DRIVERS FOR HISILICON
> +M: Xinliang Liu <z.liuxinliang@hisilicon.com>
> +R: Xinwei Kong <kong.kongxinwei@hisilicon.com>
> +R: Chen Feng <puck.chen@hisilicon.com>
> +L: dri-devel@lists.freedesktop.org
> +T: git git://github.com/xin3liang/linux.git
> +S: Maintained
> +F: drivers/gpu/drm/hisilicon
> +F: Documentation/devicetree/bindings/display/hisilicon
Nit: Can you add append '/' on these two lines.
As mentioned in commit 144308139cdce95e9c6cff3cc0ef12242181665f
"It's clearer to have patterns marked as directories."
Thanks
Emil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver
@ 2016-04-13 11:54 ` Emil Velikov
0 siblings, 0 replies; 36+ messages in thread
From: Emil Velikov @ 2016-04-13 11:54 UTC (permalink / raw)
To: linux-arm-kernel
Hi Xinliang,
On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
> Add maintainer and reviewer for hisilicon DRM driver.
>
> v8: None.
> v7: None.
> v6: None.
> v5: None.
> v4:
> - Add Chen Feng <puck.chen@hisilicon.com> as Designated reviewer.
> v3: First version.
>
> Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
> ---
> MAINTAINERS | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 61a323a6b2cf..a2ef58860689 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3840,6 +3840,16 @@ S: Maintained
> F: drivers/gpu/drm/gma500
> F: include/drm/gma500*
>
> +DRM DRIVERS FOR HISILICON
> +M: Xinliang Liu <z.liuxinliang@hisilicon.com>
> +R: Xinwei Kong <kong.kongxinwei@hisilicon.com>
> +R: Chen Feng <puck.chen@hisilicon.com>
> +L: dri-devel at lists.freedesktop.org
> +T: git git://github.com/xin3liang/linux.git
> +S: Maintained
> +F: drivers/gpu/drm/hisilicon
> +F: Documentation/devicetree/bindings/display/hisilicon
Nit: Can you add append '/' on these two lines.
As mentioned in commit 144308139cdce95e9c6cff3cc0ef12242181665f
"It's clearer to have patterns marked as directories."
Thanks
Emil
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
2016-04-11 8:55 ` Xinliang Liu
@ 2016-04-13 12:15 ` Emil Velikov
-1 siblings, 0 replies; 36+ messages in thread
From: Emil Velikov @ 2016-04-13 12:15 UTC (permalink / raw)
To: Xinliang Liu
Cc: ML dri-devel, devicetree, Daniel Vetter, Rob Herring,
Daniel Stone, Archit Taneja, David Airlie, Jonathan Corbet,
Catalin Marinas, Will Deacon, Mark Rutland, linux-doc, LAKML,
linuxarm, Andy Green, Haojian Zhuang, liguozhu, xuwei5, w.f,
puck.chen, bintian.wang, Benjamin Gaignard, xuyiping,
kong.kongxinwei, Rongrong Zou, lijianhua
Hi Xinliang,
On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
> +static int kirin_drm_connectors_register(struct drm_device *dev)
> +{
> + struct drm_connector *connector;
> + struct drm_connector *failed_connector;
> + int ret;
> +
> + mutex_lock(&dev->mode_config.mutex);
> + drm_for_each_connector(connector, dev) {
> + ret = drm_connector_register(connector);
> + if (ret) {
> + failed_connector = connector;
> + goto err;
> + }
> + }
> + mutex_unlock(&dev->mode_config.mutex);
> +
> + return 0;
> +
> +err:
> + drm_for_each_connector(connector, dev) {
> + if (failed_connector == connector)
> + break;
> + drm_connector_unregister(connector);
> + }
> + mutex_unlock(&dev->mode_config.mutex);
> +
> + return ret;
> +}
> +
Iirc we have new drm_connector_{un,}register_all() helpers.You might
want to use it once they are in (i.e. not sure what your base is and
if they have landed yet).
> +static struct device_node *kirin_get_remote_node(struct device_node *np)
> +{
> + struct device_node *endpoint, *remote;
> +
> + /* get the first endpoint, in our case only one remote node
> + * is connected to display controller.
> + */
> + endpoint = of_graph_get_next_endpoint(np, NULL);
> + if (!endpoint) {
> + DRM_ERROR("no valid endpoint node\n");
> + return ERR_PTR(-ENODEV);
> + }
> + of_node_put(endpoint);
> +
> + remote = of_graph_get_remote_port_parent(endpoint);
> + if (!remote) {
> + DRM_ERROR("no valid remote node\n");
> + return ERR_PTR(-ENODEV);
> + }
> + of_node_put(remote);
> +
> + if (!of_device_is_available(remote)) {
> + DRM_ERROR("not available for remote node\n");
> + return ERR_PTR(-ENODEV);
> + }
> +
This seems like a common pattern in many platform DRM drivers. Yet
some tend to differ in subtle ways - I'm leaning that they might be
bugs, but one cannot be too sure.
A friendly request:
Can you please follow up by adding a helper and removing the
duplication thoughout ?
Thanks
Emil
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
@ 2016-04-13 12:15 ` Emil Velikov
0 siblings, 0 replies; 36+ messages in thread
From: Emil Velikov @ 2016-04-13 12:15 UTC (permalink / raw)
To: linux-arm-kernel
Hi Xinliang,
On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
> +static int kirin_drm_connectors_register(struct drm_device *dev)
> +{
> + struct drm_connector *connector;
> + struct drm_connector *failed_connector;
> + int ret;
> +
> + mutex_lock(&dev->mode_config.mutex);
> + drm_for_each_connector(connector, dev) {
> + ret = drm_connector_register(connector);
> + if (ret) {
> + failed_connector = connector;
> + goto err;
> + }
> + }
> + mutex_unlock(&dev->mode_config.mutex);
> +
> + return 0;
> +
> +err:
> + drm_for_each_connector(connector, dev) {
> + if (failed_connector == connector)
> + break;
> + drm_connector_unregister(connector);
> + }
> + mutex_unlock(&dev->mode_config.mutex);
> +
> + return ret;
> +}
> +
Iirc we have new drm_connector_{un,}register_all() helpers.You might
want to use it once they are in (i.e. not sure what your base is and
if they have landed yet).
> +static struct device_node *kirin_get_remote_node(struct device_node *np)
> +{
> + struct device_node *endpoint, *remote;
> +
> + /* get the first endpoint, in our case only one remote node
> + * is connected to display controller.
> + */
> + endpoint = of_graph_get_next_endpoint(np, NULL);
> + if (!endpoint) {
> + DRM_ERROR("no valid endpoint node\n");
> + return ERR_PTR(-ENODEV);
> + }
> + of_node_put(endpoint);
> +
> + remote = of_graph_get_remote_port_parent(endpoint);
> + if (!remote) {
> + DRM_ERROR("no valid remote node\n");
> + return ERR_PTR(-ENODEV);
> + }
> + of_node_put(remote);
> +
> + if (!of_device_is_available(remote)) {
> + DRM_ERROR("not available for remote node\n");
> + return ERR_PTR(-ENODEV);
> + }
> +
This seems like a common pattern in many platform DRM drivers. Yet
some tend to differ in subtle ways - I'm leaning that they might be
bugs, but one cannot be too sure.
A friendly request:
Can you please follow up by adding a helper and removing the
duplication thoughout ?
Thanks
Emil
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver
2016-04-13 11:54 ` Emil Velikov
@ 2016-04-14 6:46 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-14 6:46 UTC (permalink / raw)
To: Emil Velikov
Cc: Mark Rutland, linux-doc, Catalin Marinas, Will Deacon, Linuxarm,
ML dri-devel, Xu Wei, Benjamin Gaignard, Rongrong Zou, Yiping Xu,
Jonathan Corbet, Wang Fei, devicetree, Bintian Wang, Feng Chen,
LAKML, Andy Green, Guodong Xu, Liguozhu (Kenneth),
Haojian Zhuang
On 13 April 2016 at 19:54, Emil Velikov <emil.l.velikov@gmail.com> wrote:
> Hi Xinliang,
>
> On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
>> Add maintainer and reviewer for hisilicon DRM driver.
>>
>> v8: None.
>> v7: None.
>> v6: None.
>> v5: None.
>> v4:
>> - Add Chen Feng <puck.chen@hisilicon.com> as Designated reviewer.
>> v3: First version.
>>
>> Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
>> ---
>> MAINTAINERS | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 61a323a6b2cf..a2ef58860689 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -3840,6 +3840,16 @@ S: Maintained
>> F: drivers/gpu/drm/gma500
>> F: include/drm/gma500*
>>
>> +DRM DRIVERS FOR HISILICON
>> +M: Xinliang Liu <z.liuxinliang@hisilicon.com>
>> +R: Xinwei Kong <kong.kongxinwei@hisilicon.com>
>> +R: Chen Feng <puck.chen@hisilicon.com>
>> +L: dri-devel@lists.freedesktop.org
>> +T: git git://github.com/xin3liang/linux.git
>> +S: Maintained
>> +F: drivers/gpu/drm/hisilicon
>> +F: Documentation/devicetree/bindings/display/hisilicon
> Nit: Can you add append '/' on these two lines.
>
> As mentioned in commit 144308139cdce95e9c6cff3cc0ef12242181665f
>
> "It's clearer to have patterns marked as directories."
Sure Emil, I will fix this. Thanks to notice me this.
Thanks,
-xinliang
>
> Thanks
> Emil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver
@ 2016-04-14 6:46 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-14 6:46 UTC (permalink / raw)
To: linux-arm-kernel
On 13 April 2016 at 19:54, Emil Velikov <emil.l.velikov@gmail.com> wrote:
> Hi Xinliang,
>
> On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
>> Add maintainer and reviewer for hisilicon DRM driver.
>>
>> v8: None.
>> v7: None.
>> v6: None.
>> v5: None.
>> v4:
>> - Add Chen Feng <puck.chen@hisilicon.com> as Designated reviewer.
>> v3: First version.
>>
>> Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
>> ---
>> MAINTAINERS | 10 ++++++++++
>> 1 file changed, 10 insertions(+)
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 61a323a6b2cf..a2ef58860689 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -3840,6 +3840,16 @@ S: Maintained
>> F: drivers/gpu/drm/gma500
>> F: include/drm/gma500*
>>
>> +DRM DRIVERS FOR HISILICON
>> +M: Xinliang Liu <z.liuxinliang@hisilicon.com>
>> +R: Xinwei Kong <kong.kongxinwei@hisilicon.com>
>> +R: Chen Feng <puck.chen@hisilicon.com>
>> +L: dri-devel at lists.freedesktop.org
>> +T: git git://github.com/xin3liang/linux.git
>> +S: Maintained
>> +F: drivers/gpu/drm/hisilicon
>> +F: Documentation/devicetree/bindings/display/hisilicon
> Nit: Can you add append '/' on these two lines.
>
> As mentioned in commit 144308139cdce95e9c6cff3cc0ef12242181665f
>
> "It's clearer to have patterns marked as directories."
Sure Emil, I will fix this. Thanks to notice me this.
Thanks,
-xinliang
>
> Thanks
> Emil
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
2016-04-13 12:15 ` Emil Velikov
@ 2016-04-14 7:04 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-14 7:04 UTC (permalink / raw)
To: Emil Velikov
Cc: Mark Rutland, linux-doc, Catalin Marinas, Will Deacon, Linuxarm,
ML dri-devel, Xu Wei, Benjamin Gaignard, Rongrong Zou, Yiping Xu,
Jonathan Corbet, Wang Fei, devicetree, Bintian Wang, Feng Chen,
LAKML, Andy Green, Guodong Xu, Liguozhu (Kenneth),
Haojian Zhuang
Hi Emil,
On 13 April 2016 at 20:15, Emil Velikov <emil.l.velikov@gmail.com> wrote:
> Hi Xinliang,
>
> On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
>
>> +static int kirin_drm_connectors_register(struct drm_device *dev)
>> +{
>> + struct drm_connector *connector;
>> + struct drm_connector *failed_connector;
>> + int ret;
>> +
>> + mutex_lock(&dev->mode_config.mutex);
>> + drm_for_each_connector(connector, dev) {
>> + ret = drm_connector_register(connector);
>> + if (ret) {
>> + failed_connector = connector;
>> + goto err;
>> + }
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return 0;
>> +
>> +err:
>> + drm_for_each_connector(connector, dev) {
>> + if (failed_connector == connector)
>> + break;
>> + drm_connector_unregister(connector);
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return ret;
>> +}
>> +
> Iirc we have new drm_connector_{un,}register_all() helpers.You might
> want to use it once they are in (i.e. not sure what your base is and
> if they have landed yet).
I can't find these drm_connector_{un,}register_all() helpers in latest
tag v4.6-rc3.
>
>
>> +static struct device_node *kirin_get_remote_node(struct device_node *np)
>> +{
>> + struct device_node *endpoint, *remote;
>> +
>> + /* get the first endpoint, in our case only one remote node
>> + * is connected to display controller.
>> + */
>> + endpoint = of_graph_get_next_endpoint(np, NULL);
>> + if (!endpoint) {
>> + DRM_ERROR("no valid endpoint node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(endpoint);
>> +
>> + remote = of_graph_get_remote_port_parent(endpoint);
>> + if (!remote) {
>> + DRM_ERROR("no valid remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(remote);
>> +
>> + if (!of_device_is_available(remote)) {
>> + DRM_ERROR("not available for remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> +
> This seems like a common pattern in many platform DRM drivers. Yet
> some tend to differ in subtle ways - I'm leaning that they might be
> bugs, but one cannot be too sure.
>
> A friendly request:
> Can you please follow up by adding a helper and removing the
> duplication thoughout ?
Yes, I will create another patch set for this. I think I need to
figure out other drivers requirements.
Maybe, I need to add one more parameter for this helper. That's
endpoint index to get which endpoint remote node.
I will follow up this.
Thanks,
-xinliang
>
> Thanks
> Emil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
@ 2016-04-14 7:04 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-04-14 7:04 UTC (permalink / raw)
To: linux-arm-kernel
Hi Emil,
On 13 April 2016 at 20:15, Emil Velikov <emil.l.velikov@gmail.com> wrote:
> Hi Xinliang,
>
> On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
>
>> +static int kirin_drm_connectors_register(struct drm_device *dev)
>> +{
>> + struct drm_connector *connector;
>> + struct drm_connector *failed_connector;
>> + int ret;
>> +
>> + mutex_lock(&dev->mode_config.mutex);
>> + drm_for_each_connector(connector, dev) {
>> + ret = drm_connector_register(connector);
>> + if (ret) {
>> + failed_connector = connector;
>> + goto err;
>> + }
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return 0;
>> +
>> +err:
>> + drm_for_each_connector(connector, dev) {
>> + if (failed_connector == connector)
>> + break;
>> + drm_connector_unregister(connector);
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return ret;
>> +}
>> +
> Iirc we have new drm_connector_{un,}register_all() helpers.You might
> want to use it once they are in (i.e. not sure what your base is and
> if they have landed yet).
I can't find these drm_connector_{un,}register_all() helpers in latest
tag v4.6-rc3.
>
>
>> +static struct device_node *kirin_get_remote_node(struct device_node *np)
>> +{
>> + struct device_node *endpoint, *remote;
>> +
>> + /* get the first endpoint, in our case only one remote node
>> + * is connected to display controller.
>> + */
>> + endpoint = of_graph_get_next_endpoint(np, NULL);
>> + if (!endpoint) {
>> + DRM_ERROR("no valid endpoint node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(endpoint);
>> +
>> + remote = of_graph_get_remote_port_parent(endpoint);
>> + if (!remote) {
>> + DRM_ERROR("no valid remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(remote);
>> +
>> + if (!of_device_is_available(remote)) {
>> + DRM_ERROR("not available for remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> +
> This seems like a common pattern in many platform DRM drivers. Yet
> some tend to differ in subtle ways - I'm leaning that they might be
> bugs, but one cannot be too sure.
>
> A friendly request:
> Can you please follow up by adding a helper and removing the
> duplication thoughout ?
Yes, I will create another patch set for this. I think I need to
figure out other drivers requirements.
Maybe, I need to add one more parameter for this helper. That's
endpoint index to get which endpoint remote node.
I will follow up this.
Thanks,
-xinliang
>
> Thanks
> Emil
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
2016-04-13 12:15 ` Emil Velikov
@ 2016-06-30 9:31 ` Xinliang Liu
-1 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-06-30 9:31 UTC (permalink / raw)
To: Emil Velikov
Cc: Mark Rutland, linux-doc, Catalin Marinas, Will Deacon, Linuxarm,
ML dri-devel, Xu Wei, Rongrong Zou, Yiping Xu, Jonathan Corbet,
Wang Fei, devicetree, Bintian Wang, Feng Chen, LAKML, Andy Green,
Guodong Xu, Liguozhu (Kenneth),
Haojian Zhuang
On 13 April 2016 at 20:15, Emil Velikov <emil.l.velikov@gmail.com> wrote:
> Hi Xinliang,
>
> On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
>
>> +static int kirin_drm_connectors_register(struct drm_device *dev)
>> +{
>> + struct drm_connector *connector;
>> + struct drm_connector *failed_connector;
>> + int ret;
>> +
>> + mutex_lock(&dev->mode_config.mutex);
>> + drm_for_each_connector(connector, dev) {
>> + ret = drm_connector_register(connector);
>> + if (ret) {
>> + failed_connector = connector;
>> + goto err;
>> + }
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return 0;
>> +
>> +err:
>> + drm_for_each_connector(connector, dev) {
>> + if (failed_connector == connector)
>> + break;
>> + drm_connector_unregister(connector);
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return ret;
>> +}
>> +
> Iirc we have new drm_connector_{un,}register_all() helpers.You might
> want to use it once they are in (i.e. not sure what your base is and
> if they have landed yet).
>
>
>> +static struct device_node *kirin_get_remote_node(struct device_node *np)
>> +{
>> + struct device_node *endpoint, *remote;
>> +
>> + /* get the first endpoint, in our case only one remote node
>> + * is connected to display controller.
>> + */
>> + endpoint = of_graph_get_next_endpoint(np, NULL);
>> + if (!endpoint) {
>> + DRM_ERROR("no valid endpoint node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(endpoint);
>> +
>> + remote = of_graph_get_remote_port_parent(endpoint);
>> + if (!remote) {
>> + DRM_ERROR("no valid remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(remote);
>> +
>> + if (!of_device_is_available(remote)) {
>> + DRM_ERROR("not available for remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> +
> This seems like a common pattern in many platform DRM drivers. Yet
> some tend to differ in subtle ways - I'm leaning that they might be
> bugs, but one cannot be too sure.
>
> A friendly request:
> Can you please follow up by adding a helper and removing the
> duplication thoughout ?
Hi emil, recently I found that there is already a helper to do such work.
It is drm_of_component_probe.
-xinliang
>
> Thanks
> Emil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver
@ 2016-06-30 9:31 ` Xinliang Liu
0 siblings, 0 replies; 36+ messages in thread
From: Xinliang Liu @ 2016-06-30 9:31 UTC (permalink / raw)
To: linux-arm-kernel
On 13 April 2016 at 20:15, Emil Velikov <emil.l.velikov@gmail.com> wrote:
> Hi Xinliang,
>
> On 11 April 2016 at 09:55, Xinliang Liu <xinliang.liu@linaro.org> wrote:
>
>> +static int kirin_drm_connectors_register(struct drm_device *dev)
>> +{
>> + struct drm_connector *connector;
>> + struct drm_connector *failed_connector;
>> + int ret;
>> +
>> + mutex_lock(&dev->mode_config.mutex);
>> + drm_for_each_connector(connector, dev) {
>> + ret = drm_connector_register(connector);
>> + if (ret) {
>> + failed_connector = connector;
>> + goto err;
>> + }
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return 0;
>> +
>> +err:
>> + drm_for_each_connector(connector, dev) {
>> + if (failed_connector == connector)
>> + break;
>> + drm_connector_unregister(connector);
>> + }
>> + mutex_unlock(&dev->mode_config.mutex);
>> +
>> + return ret;
>> +}
>> +
> Iirc we have new drm_connector_{un,}register_all() helpers.You might
> want to use it once they are in (i.e. not sure what your base is and
> if they have landed yet).
>
>
>> +static struct device_node *kirin_get_remote_node(struct device_node *np)
>> +{
>> + struct device_node *endpoint, *remote;
>> +
>> + /* get the first endpoint, in our case only one remote node
>> + * is connected to display controller.
>> + */
>> + endpoint = of_graph_get_next_endpoint(np, NULL);
>> + if (!endpoint) {
>> + DRM_ERROR("no valid endpoint node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(endpoint);
>> +
>> + remote = of_graph_get_remote_port_parent(endpoint);
>> + if (!remote) {
>> + DRM_ERROR("no valid remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> + of_node_put(remote);
>> +
>> + if (!of_device_is_available(remote)) {
>> + DRM_ERROR("not available for remote node\n");
>> + return ERR_PTR(-ENODEV);
>> + }
>> +
> This seems like a common pattern in many platform DRM drivers. Yet
> some tend to differ in subtle ways - I'm leaning that they might be
> bugs, but one cannot be too sure.
>
> A friendly request:
> Can you please follow up by adding a helper and removing the
> duplication thoughout ?
Hi emil, recently I found that there is already a helper to do such work.
It is drm_of_component_probe.
-xinliang
>
> Thanks
> Emil
^ permalink raw reply [flat|nested] 36+ messages in thread
end of thread, other threads:[~2016-06-30 9:31 UTC | newest]
Thread overview: 36+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-04-11 8:55 [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 01/10] drm/hisilicon: Add device tree binding for hi6220 display subsystem Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
[not found] ` <1460364943-76135-1-git-send-email-xinliang.liu-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2016-04-11 8:55 ` [PATCH v8 02/10] drm/hisilicon: Add hisilicon kirin drm master driver Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-13 12:15 ` Emil Velikov
2016-04-13 12:15 ` Emil Velikov
2016-04-14 7:04 ` Xinliang Liu
2016-04-14 7:04 ` Xinliang Liu
2016-06-30 9:31 ` Xinliang Liu
2016-06-30 9:31 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 03/10] drm/hisilicon: Add crtc driver for ADE Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 04/10] drm/hisilicon: Add plane " Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 05/10] drm/hisilicon: Add vblank " Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 06/10] drm/hisilicon: Add cma fbdev and hotplug Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 07/10] drm/hisilicon: Add designware dsi encoder driver Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 08/10] drm/hisilicon: Add designware dsi host driver Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 09/10] drm/hisilicon: Add support for external bridge Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-11 8:55 ` [PATCH v8 10/10] MAINTAINERS: Add maintainer for hisilicon DRM driver Xinliang Liu
2016-04-11 8:55 ` Xinliang Liu
2016-04-13 11:54 ` Emil Velikov
2016-04-13 11:54 ` Emil Velikov
2016-04-14 6:46 ` Xinliang Liu
2016-04-14 6:46 ` Xinliang Liu
2016-04-12 16:08 ` [PATCH v8 00/10] Add DRM Driver for HiSilicon Kirin hi6220 SoC Daniel Vetter
2016-04-12 16:08 ` Daniel Vetter
2016-04-13 1:12 ` Xinliang Liu
2016-04-13 1:12 ` Xinliang Liu
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.