* [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
@ 2020-07-16 6:14 ` Cheng-Yi Chiang
0 siblings, 0 replies; 7+ messages in thread
From: Cheng-Yi Chiang @ 2020-07-16 6:14 UTC (permalink / raw)
To: linux-kernel
Cc: Taniya Das, Rohit kumar, Andy Gross, Bjorn Andersson,
Rob Herring, dianders, linux-arm-kernel, linux-arm-msm,
devicetree, Ajit Pandey, Cheng-Yi Chiang
From: Ajit Pandey <ajitp@codeaurora.org>
Add the I2S controller node to sc7180 dtsi.
Add pinmux for pirmary and secondary I2S.
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
---
This patch depends on these patch series so it is not ready to be merged now.
- clk: qcom: Support for Low Power Audio Clocks on SC7180 https://patchwork.kernel.org/cover/11664273/
- arm64: dts: qcom: sc7180: Add LPASS clock controller nodes https://patchwork.kernel.org/patch/11664303/
- ASoC: qcom: Add support for SC7180 lpass variant https://patchwork.kernel.org/cover/11650649/
arch/arm64/boot/dts/qcom/sc7180.dtsi | 132 +++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 6eb14b6a47f5..2fe3bd89f950 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -511,6 +511,34 @@ qusb2p_hstx_trim: hstx-trim-primary@25b {
};
};
+ lpass_cpu: lpass {
+ compatible = "qcom,lpass-cpu-sc7180";
+
+ reg = <0 0x62F00000 0 0x29000>;
+ reg-names = "lpass-lpaif";
+
+ iommus = <&apps_smmu 0x1020 0>;
+
+ power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>;
+
+ status = "disabled";
+
+ clocks = <&gcc GCC_LPASS_CFG_NOC_SWAY_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_CORE_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_EXT_MCLK0_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_SYSNOC_MPORT_CORE_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_LPAIF_PRI_IBIT_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_LPAIF_SEC_IBIT_CLK>;
+
+ clock-names = "noc", "audio-core", "mclk0", "sysnoc_mport",
+ "pri_ibit", "sec_ibit";
+
+ #sound-dai-cells = <1>;
+
+ interrupts = <0 160 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "lpass-irq-lpaif";
+ };
+
sdhc_1: sdhci@7c4000 {
compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
reg = <0 0x7c4000 0 0x1000>,
@@ -1357,6 +1385,110 @@ pinmux {
};
};
+ sec_mi2s_active: sec-mi2s-active {
+ pinmux {
+ pins = "gpio49";
+ function = "mi2s_1";
+ };
+
+ pinconf {
+ pins = "gpio49";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ sec_mi2s_ws_active: sec-mi2s-ws-active {
+ pinmux {
+ pins = "gpio50";
+ function = "mi2s_1";
+ };
+
+ pinconf {
+ pins = "gpio50";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ sec_mi2s_dout_active: sec-mi2s-dout-active {
+ pinmux {
+ pins = "gpio51";
+ function = "mi2s_1";
+ };
+
+ pinconf {
+ pins = "gpio51";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_active: pri-mi2s-active {
+ pinmux {
+ pins = "gpio53";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio53";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_ws_active: pri-mi2s-ws-active {
+ pinmux {
+ pins = "gpio54";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio54";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_dout_active: pri-mi2s-dout-active {
+ pinmux {
+ pins = "gpio55";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio55";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_din_active: pri-mi2s-din-active {
+ pinmux {
+ pins = "gpio56";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio56";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_mclk_active: pri-mi2s-mclk-active {
+ pinmux {
+ pins = "gpio57";
+ function = "lpass_ext";
+ };
+
+ pinconf {
+ pins = "gpio57";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
sdc1_on: sdc1-on {
pinconf-clk {
pins = "sdc1_clk";
--
2.28.0.rc0.105.gf9edc3c819-goog
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
@ 2020-07-16 6:14 ` Cheng-Yi Chiang
0 siblings, 0 replies; 7+ messages in thread
From: Cheng-Yi Chiang @ 2020-07-16 6:14 UTC (permalink / raw)
To: linux-kernel
Cc: Taniya Das, devicetree, linux-arm-msm, dianders, Rob Herring,
Bjorn Andersson, Andy Gross, Rohit kumar, Ajit Pandey,
linux-arm-kernel, Cheng-Yi Chiang
From: Ajit Pandey <ajitp@codeaurora.org>
Add the I2S controller node to sc7180 dtsi.
Add pinmux for pirmary and secondary I2S.
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
---
This patch depends on these patch series so it is not ready to be merged now.
- clk: qcom: Support for Low Power Audio Clocks on SC7180 https://patchwork.kernel.org/cover/11664273/
- arm64: dts: qcom: sc7180: Add LPASS clock controller nodes https://patchwork.kernel.org/patch/11664303/
- ASoC: qcom: Add support for SC7180 lpass variant https://patchwork.kernel.org/cover/11650649/
arch/arm64/boot/dts/qcom/sc7180.dtsi | 132 +++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 6eb14b6a47f5..2fe3bd89f950 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -511,6 +511,34 @@ qusb2p_hstx_trim: hstx-trim-primary@25b {
};
};
+ lpass_cpu: lpass {
+ compatible = "qcom,lpass-cpu-sc7180";
+
+ reg = <0 0x62F00000 0 0x29000>;
+ reg-names = "lpass-lpaif";
+
+ iommus = <&apps_smmu 0x1020 0>;
+
+ power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>;
+
+ status = "disabled";
+
+ clocks = <&gcc GCC_LPASS_CFG_NOC_SWAY_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_CORE_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_EXT_MCLK0_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_SYSNOC_MPORT_CORE_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_LPAIF_PRI_IBIT_CLK>,
+ <&lpasscc LPASS_AUDIO_CORE_LPAIF_SEC_IBIT_CLK>;
+
+ clock-names = "noc", "audio-core", "mclk0", "sysnoc_mport",
+ "pri_ibit", "sec_ibit";
+
+ #sound-dai-cells = <1>;
+
+ interrupts = <0 160 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "lpass-irq-lpaif";
+ };
+
sdhc_1: sdhci@7c4000 {
compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
reg = <0 0x7c4000 0 0x1000>,
@@ -1357,6 +1385,110 @@ pinmux {
};
};
+ sec_mi2s_active: sec-mi2s-active {
+ pinmux {
+ pins = "gpio49";
+ function = "mi2s_1";
+ };
+
+ pinconf {
+ pins = "gpio49";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ sec_mi2s_ws_active: sec-mi2s-ws-active {
+ pinmux {
+ pins = "gpio50";
+ function = "mi2s_1";
+ };
+
+ pinconf {
+ pins = "gpio50";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ sec_mi2s_dout_active: sec-mi2s-dout-active {
+ pinmux {
+ pins = "gpio51";
+ function = "mi2s_1";
+ };
+
+ pinconf {
+ pins = "gpio51";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_active: pri-mi2s-active {
+ pinmux {
+ pins = "gpio53";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio53";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_ws_active: pri-mi2s-ws-active {
+ pinmux {
+ pins = "gpio54";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio54";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_dout_active: pri-mi2s-dout-active {
+ pinmux {
+ pins = "gpio55";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio55";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_din_active: pri-mi2s-din-active {
+ pinmux {
+ pins = "gpio56";
+ function = "mi2s_0";
+ };
+
+ pinconf {
+ pins = "gpio56";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ pri_mi2s_mclk_active: pri-mi2s-mclk-active {
+ pinmux {
+ pins = "gpio57";
+ function = "lpass_ext";
+ };
+
+ pinconf {
+ pins = "gpio57";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
sdc1_on: sdc1-on {
pinconf-clk {
pins = "sdc1_clk";
--
2.28.0.rc0.105.gf9edc3c819-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
2020-07-16 6:14 ` Cheng-Yi Chiang
@ 2020-07-16 18:05 ` Doug Anderson
-1 siblings, 0 replies; 7+ messages in thread
From: Doug Anderson @ 2020-07-16 18:05 UTC (permalink / raw)
To: Cheng-Yi Chiang
Cc: LKML, Taniya Das, Rohit kumar, Andy Gross, Bjorn Andersson,
Rob Herring, Linux ARM, linux-arm-msm,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Ajit Pandey
Hi,
On Wed, Jul 15, 2020 at 11:14 PM Cheng-Yi Chiang <cychiang@chromium.org> wrote:
>
> From: Ajit Pandey <ajitp@codeaurora.org>
>
> Add the I2S controller node to sc7180 dtsi.
> Add pinmux for pirmary and secondary I2S.
s/pirmary/primary
>
> Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
> Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
> ---
> This patch depends on these patch series so it is not ready to be merged now.
> - clk: qcom: Support for Low Power Audio Clocks on SC7180 https://patchwork.kernel.org/cover/11664273/
> - arm64: dts: qcom: sc7180: Add LPASS clock controller nodes https://patchwork.kernel.org/patch/11664303/
> - ASoC: qcom: Add support for SC7180 lpass variant https://patchwork.kernel.org/cover/11650649/
Thanks for pointing out the dependencies!
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 132 +++++++++++++++++++++++++++
> 1 file changed, 132 insertions(+)
My review is a bit rote since I don't actually know anything about
audio. This is mostly just a dt-hygiene review.
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 6eb14b6a47f5..2fe3bd89f950 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -511,6 +511,34 @@ qusb2p_hstx_trim: hstx-trim-primary@25b {
> };
> };
>
> + lpass_cpu: lpass {
Missing unit address and also sorted incorrectly. Nodes should be
sorted by unit address.
> + compatible = "qcom,lpass-cpu-sc7180";
Is there a pin config that generally makes sense for all boards? If
so, you can add it here so it doesn't need to be added to all
sub-boards.
> + reg = <0 0x62F00000 0 0x29000>;
nit: lower case hex for reg address, so 62f not 62F.
> + reg-names = "lpass-lpaif";
> +
> + iommus = <&apps_smmu 0x1020 0>;
> +
> + power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>;
> +
> + status = "disabled";
> +
> + clocks = <&gcc GCC_LPASS_CFG_NOC_SWAY_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_CORE_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_EXT_MCLK0_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_SYSNOC_MPORT_CORE_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_LPAIF_PRI_IBIT_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_LPAIF_SEC_IBIT_CLK>;
> +
> + clock-names = "noc", "audio-core", "mclk0", "sysnoc_mport",
> + "pri_ibit", "sec_ibit";
> +
> + #sound-dai-cells = <1>;
> +
> + interrupts = <0 160 IRQ_TYPE_LEVEL_HIGH>;
First entry of interrupts should be GIC_SPI, which is what 0 is referring to.
> + interrupt-names = "lpass-irq-lpaif";
> + };
Bindings claim you're supposed to have:
#address-cells = <1>;
#size-cells = <0>;
Do you not need them for some reason?
> sdhc_1: sdhci@7c4000 {
> compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
> reg = <0 0x7c4000 0 0x1000>,
> @@ -1357,6 +1385,110 @@ pinmux {
> };
> };
>
> + sec_mi2s_active: sec-mi2s-active {
> + pinmux {
> + pins = "gpio49";
> + function = "mi2s_1";
> + };
> +
> + pinconf {
> + pins = "gpio49";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + sec_mi2s_ws_active: sec-mi2s-ws-active {
> + pinmux {
> + pins = "gpio50";
> + function = "mi2s_1";
> + };
> +
> + pinconf {
> + pins = "gpio50";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + sec_mi2s_dout_active: sec-mi2s-dout-active {
> + pinmux {
> + pins = "gpio51";
> + function = "mi2s_1";
> + };
> +
> + pinconf {
> + pins = "gpio51";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_active: pri-mi2s-active {
> + pinmux {
> + pins = "gpio53";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio53";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_ws_active: pri-mi2s-ws-active {
> + pinmux {
> + pins = "gpio54";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio54";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_dout_active: pri-mi2s-dout-active {
> + pinmux {
> + pins = "gpio55";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio55";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_din_active: pri-mi2s-din-active {
> + pinmux {
> + pins = "gpio56";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio56";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
Can you group together any of the configs? See, for instance,
"qup_spi0_default" where we configure 4 pins together. Then you don't
need so many separate nodes to add.
Also: pinconf is nearly always done in board files unless you truly
have a reason to believe that it would be the same for every board.
> + pri_mi2s_mclk_active: pri-mi2s-mclk-active {
> + pinmux {
> + pins = "gpio57";
> + function = "lpass_ext";
> + };
> +
> + pinconf {
> + pins = "gpio57";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> sdc1_on: sdc1-on {
> pinconf-clk {
> pins = "sdc1_clk";
-Doug
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
@ 2020-07-16 18:05 ` Doug Anderson
0 siblings, 0 replies; 7+ messages in thread
From: Doug Anderson @ 2020-07-16 18:05 UTC (permalink / raw)
To: Cheng-Yi Chiang
Cc: Taniya Das,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-arm-msm, LKML, Rob Herring, Bjorn Andersson, Andy Gross,
Rohit kumar, Ajit Pandey, Linux ARM
Hi,
On Wed, Jul 15, 2020 at 11:14 PM Cheng-Yi Chiang <cychiang@chromium.org> wrote:
>
> From: Ajit Pandey <ajitp@codeaurora.org>
>
> Add the I2S controller node to sc7180 dtsi.
> Add pinmux for pirmary and secondary I2S.
s/pirmary/primary
>
> Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
> Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
> ---
> This patch depends on these patch series so it is not ready to be merged now.
> - clk: qcom: Support for Low Power Audio Clocks on SC7180 https://patchwork.kernel.org/cover/11664273/
> - arm64: dts: qcom: sc7180: Add LPASS clock controller nodes https://patchwork.kernel.org/patch/11664303/
> - ASoC: qcom: Add support for SC7180 lpass variant https://patchwork.kernel.org/cover/11650649/
Thanks for pointing out the dependencies!
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 132 +++++++++++++++++++++++++++
> 1 file changed, 132 insertions(+)
My review is a bit rote since I don't actually know anything about
audio. This is mostly just a dt-hygiene review.
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 6eb14b6a47f5..2fe3bd89f950 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -511,6 +511,34 @@ qusb2p_hstx_trim: hstx-trim-primary@25b {
> };
> };
>
> + lpass_cpu: lpass {
Missing unit address and also sorted incorrectly. Nodes should be
sorted by unit address.
> + compatible = "qcom,lpass-cpu-sc7180";
Is there a pin config that generally makes sense for all boards? If
so, you can add it here so it doesn't need to be added to all
sub-boards.
> + reg = <0 0x62F00000 0 0x29000>;
nit: lower case hex for reg address, so 62f not 62F.
> + reg-names = "lpass-lpaif";
> +
> + iommus = <&apps_smmu 0x1020 0>;
> +
> + power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>;
> +
> + status = "disabled";
> +
> + clocks = <&gcc GCC_LPASS_CFG_NOC_SWAY_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_CORE_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_EXT_MCLK0_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_SYSNOC_MPORT_CORE_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_LPAIF_PRI_IBIT_CLK>,
> + <&lpasscc LPASS_AUDIO_CORE_LPAIF_SEC_IBIT_CLK>;
> +
> + clock-names = "noc", "audio-core", "mclk0", "sysnoc_mport",
> + "pri_ibit", "sec_ibit";
> +
> + #sound-dai-cells = <1>;
> +
> + interrupts = <0 160 IRQ_TYPE_LEVEL_HIGH>;
First entry of interrupts should be GIC_SPI, which is what 0 is referring to.
> + interrupt-names = "lpass-irq-lpaif";
> + };
Bindings claim you're supposed to have:
#address-cells = <1>;
#size-cells = <0>;
Do you not need them for some reason?
> sdhc_1: sdhci@7c4000 {
> compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
> reg = <0 0x7c4000 0 0x1000>,
> @@ -1357,6 +1385,110 @@ pinmux {
> };
> };
>
> + sec_mi2s_active: sec-mi2s-active {
> + pinmux {
> + pins = "gpio49";
> + function = "mi2s_1";
> + };
> +
> + pinconf {
> + pins = "gpio49";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + sec_mi2s_ws_active: sec-mi2s-ws-active {
> + pinmux {
> + pins = "gpio50";
> + function = "mi2s_1";
> + };
> +
> + pinconf {
> + pins = "gpio50";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + sec_mi2s_dout_active: sec-mi2s-dout-active {
> + pinmux {
> + pins = "gpio51";
> + function = "mi2s_1";
> + };
> +
> + pinconf {
> + pins = "gpio51";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_active: pri-mi2s-active {
> + pinmux {
> + pins = "gpio53";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio53";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_ws_active: pri-mi2s-ws-active {
> + pinmux {
> + pins = "gpio54";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio54";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_dout_active: pri-mi2s-dout-active {
> + pinmux {
> + pins = "gpio55";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio55";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> + pri_mi2s_din_active: pri-mi2s-din-active {
> + pinmux {
> + pins = "gpio56";
> + function = "mi2s_0";
> + };
> +
> + pinconf {
> + pins = "gpio56";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
Can you group together any of the configs? See, for instance,
"qup_spi0_default" where we configure 4 pins together. Then you don't
need so many separate nodes to add.
Also: pinconf is nearly always done in board files unless you truly
have a reason to believe that it would be the same for every board.
> + pri_mi2s_mclk_active: pri-mi2s-mclk-active {
> + pinmux {
> + pins = "gpio57";
> + function = "lpass_ext";
> + };
> +
> + pinconf {
> + pins = "gpio57";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> + };
> +
> sdc1_on: sdc1-on {
> pinconf-clk {
> pins = "sdc1_clk";
-Doug
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
2020-07-16 6:14 ` Cheng-Yi Chiang
(?)
@ 2020-07-17 12:58 ` kernel test robot
-1 siblings, 0 replies; 7+ messages in thread
From: kernel test robot @ 2020-07-17 12:58 UTC (permalink / raw)
To: Cheng-Yi Chiang, linux-kernel
Cc: kbuild-all, clang-built-linux, Taniya Das, Rohit kumar,
Andy Gross, Bjorn Andersson, Rob Herring, dianders,
linux-arm-kernel, linux-arm-msm, devicetree
[-- Attachment #1: Type: text/plain, Size: 1558 bytes --]
Hi Cheng-Yi,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on linux/master linus/master v5.8-rc5 next-20200716]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Cheng-Yi-Chiang/arm64-dts-qcom-sc7180-Add-lpass-cpu-node-for-I2S-driver/20200716-141836
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-randconfig-r014-20200717 (attached as .config)
compiler: clang version 12.0.0 (https://github.com/llvm/llvm-project ed6b578040a85977026c93bf4188f996148f3218)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross ARCH=arm64
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/qcom/sc7180.dtsi:521.31-32 syntax error
>> FATAL ERROR: Unable to parse input tree
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 41038 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
@ 2020-07-17 12:58 ` kernel test robot
0 siblings, 0 replies; 7+ messages in thread
From: kernel test robot @ 2020-07-17 12:58 UTC (permalink / raw)
To: Cheng-Yi Chiang, linux-kernel
Cc: Taniya Das, devicetree, kbuild-all, linux-arm-msm, dianders,
Rob Herring, Bjorn Andersson, clang-built-linux, Andy Gross,
Rohit kumar, linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1558 bytes --]
Hi Cheng-Yi,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on linux/master linus/master v5.8-rc5 next-20200716]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Cheng-Yi-Chiang/arm64-dts-qcom-sc7180-Add-lpass-cpu-node-for-I2S-driver/20200716-141836
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-randconfig-r014-20200717 (attached as .config)
compiler: clang version 12.0.0 (https://github.com/llvm/llvm-project ed6b578040a85977026c93bf4188f996148f3218)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross ARCH=arm64
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/qcom/sc7180.dtsi:521.31-32 syntax error
>> FATAL ERROR: Unable to parse input tree
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 41038 bytes --]
[-- Attachment #3: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
@ 2020-07-17 12:58 ` kernel test robot
0 siblings, 0 replies; 7+ messages in thread
From: kernel test robot @ 2020-07-17 12:58 UTC (permalink / raw)
To: kbuild-all
[-- Attachment #1: Type: text/plain, Size: 1593 bytes --]
Hi Cheng-Yi,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on linux/master linus/master v5.8-rc5 next-20200716]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Cheng-Yi-Chiang/arm64-dts-qcom-sc7180-Add-lpass-cpu-node-for-I2S-driver/20200716-141836
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-randconfig-r014-20200717 (attached as .config)
compiler: clang version 12.0.0 (https://github.com/llvm/llvm-project ed6b578040a85977026c93bf4188f996148f3218)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross ARCH=arm64
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/qcom/sc7180.dtsi:521.31-32 syntax error
>> FATAL ERROR: Unable to parse input tree
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org
[-- Attachment #2: config.gz --]
[-- Type: application/gzip, Size: 41038 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2020-07-17 13:03 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-16 6:14 [PATCH] arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver Cheng-Yi Chiang
2020-07-16 6:14 ` Cheng-Yi Chiang
2020-07-16 18:05 ` Doug Anderson
2020-07-16 18:05 ` Doug Anderson
2020-07-17 12:58 ` kernel test robot
2020-07-17 12:58 ` kernel test robot
2020-07-17 12:58 ` kernel test robot
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.