* ath11k: does qmi support multiple soc
@ 2022-04-18 8:37 fengbin
2022-04-18 9:27 ` Robert Marko
2022-04-22 15:43 ` Jeff Johnson
0 siblings, 2 replies; 6+ messages in thread
From: fengbin @ 2022-04-18 8:37 UTC (permalink / raw)
To: ath11k
Hello,
I have qca6390 and qcn9074 both of them works fine individually.
However when I install them together errors show up.
here is log with only 9074 installed:
[ 17.759191] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
connected qmi:00000000181299d3 node:7, port:2
[ 17.759197] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2709 qmi:00000000181299d3
[ 17.760436] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2718 qmi:00000000181299d3
fw_ind_register completed.
[ 17.761703] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2725 qmi:00000000181299d3
fw_ind_register host_cap completed.
[ 17.767555] ath11k_pci 0000:01:00.0: chip_id 0x0 chip_family 0x0
board_id 0xff soc_id 0xffffffff
[ 17.767559] ath11k_pci 0000:01:00.0: fw_version 0x2506844c
fw_build_timestamp 2021-07-13 10:24 fw_build_id
[ 19.495395] ath11k_pci 0000:01:00.0 wlp1s0: renamed from wlan0
and here is log with 6390+9074 and from the log it seems 01:00.01
device get same qmi messages twice and thus the host_cap request
failed the second time where chipset FW consider the host_cap request
is in bad state.
[ 19.106915] ath11k_pci 0000:01:00.0: BAR 0: assigned [mem
0x92000000-0x921fffff 64bit]
[ 19.106947] ath11k_pci 0000:01:00.0: enabling device (0100 -> 0102)
[ 19.107355] ath11k_pci 0000:01:00.0: MSI vectors: 16
[ 19.107366] ath11k_pci 0000:01:00.0: qcn9074 hw1.0
[ 19.107505] ath11k_pci 0000:01:00.0: mhi controller registered
:0000000054128108 mhi_ctrl->index:0 mhi_ctrl->mhi_dev:mhi0
[ 20.173172] ath11k_pci 0000:05:00.0: BAR 0: assigned [mem
0x91000000-0x91ffffff 64bit]
[ 20.173218] ath11k_pci 0000:05:00.0: enabling device (0100 -> 0102)
[ 20.173937] ath11k_pci 0000:05:00.0: MSI vectors: 32
[ 20.173959] ath11k_pci 0000:05:00.0: qca6390 hw2.0
[ 20.174111] ath11k_pci 0000:05:00.0: mhi controller registered
:00000000c33f02d3 mhi_ctrl->index:1 mhi_ctrl->mhi_dev:mhi1
[ 20.767399] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
connected qmi:00000000e25ddf03 node:7, port:2
[ 20.767423] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2709 qmi:00000000e25ddf03
[ 20.768739] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2718 qmi:00000000e25ddf03
fw_ind_register completed.
[ 20.770333] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2725 qmi:00000000e25ddf03
fw_ind_register host_cap completed.
[ 20.770375] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
connected qmi:00000000e25ddf03 node:7, port:2
[ 20.771668] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2709 qmi:00000000e25ddf03
[ 20.776796] ath11k_pci 0000:01:00.0:
ath11k_qmi_event_server_arrive@2718 qmi:00000000e25ddf03
fw_ind_register completed.
[ 20.778021] ath11k_pci 0000:01:00.0: host capability request failed: 1 90
Any thoughts and ideas of what might be the cause?
thanks
--
arithdon
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: ath11k: does qmi support multiple soc
2022-04-18 8:37 ath11k: does qmi support multiple soc fengbin
@ 2022-04-18 9:27 ` Robert Marko
2022-04-18 10:13 ` fengbin
2022-04-22 15:43 ` Jeff Johnson
1 sibling, 1 reply; 6+ messages in thread
From: Robert Marko @ 2022-04-18 9:27 UTC (permalink / raw)
To: fengbin; +Cc: ath11k
On Mon, Apr 18, 2022 at 10:37 AM fengbin <arithdon@gmail.com> wrote:
>
> Hello,
> I have qca6390 and qcn9074 both of them works fine individually.
> However when I install them together errors show up.
>
>
> here is log with only 9074 installed:
> [ 17.759191] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
> connected qmi:00000000181299d3 node:7, port:2
> [ 17.759197] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2709 qmi:00000000181299d3
> [ 17.760436] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2718 qmi:00000000181299d3
> fw_ind_register completed.
> [ 17.761703] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2725 qmi:00000000181299d3
> fw_ind_register host_cap completed.
> [ 17.767555] ath11k_pci 0000:01:00.0: chip_id 0x0 chip_family 0x0
> board_id 0xff soc_id 0xffffffff
> [ 17.767559] ath11k_pci 0000:01:00.0: fw_version 0x2506844c
> fw_build_timestamp 2021-07-13 10:24 fw_build_id
> [ 19.495395] ath11k_pci 0000:01:00.0 wlp1s0: renamed from wlan0
>
> and here is log with 6390+9074 and from the log it seems 01:00.01
> device get same qmi messages twice and thus the host_cap request
> failed the second time where chipset FW consider the host_cap request
> is in bad state.
>
> [ 19.106915] ath11k_pci 0000:01:00.0: BAR 0: assigned [mem
> 0x92000000-0x921fffff 64bit]
> [ 19.106947] ath11k_pci 0000:01:00.0: enabling device (0100 -> 0102)
> [ 19.107355] ath11k_pci 0000:01:00.0: MSI vectors: 16
> [ 19.107366] ath11k_pci 0000:01:00.0: qcn9074 hw1.0
> [ 19.107505] ath11k_pci 0000:01:00.0: mhi controller registered
> :0000000054128108 mhi_ctrl->index:0 mhi_ctrl->mhi_dev:mhi0
> [ 20.173172] ath11k_pci 0000:05:00.0: BAR 0: assigned [mem
> 0x91000000-0x91ffffff 64bit]
> [ 20.173218] ath11k_pci 0000:05:00.0: enabling device (0100 -> 0102)
> [ 20.173937] ath11k_pci 0000:05:00.0: MSI vectors: 32
> [ 20.173959] ath11k_pci 0000:05:00.0: qca6390 hw2.0
> [ 20.174111] ath11k_pci 0000:05:00.0: mhi controller registered
> :00000000c33f02d3 mhi_ctrl->index:1 mhi_ctrl->mhi_dev:mhi1
> [ 20.767399] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
> connected qmi:00000000e25ddf03 node:7, port:2
> [ 20.767423] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2709 qmi:00000000e25ddf03
> [ 20.768739] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2718 qmi:00000000e25ddf03
> fw_ind_register completed.
> [ 20.770333] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2725 qmi:00000000e25ddf03
> fw_ind_register host_cap completed.
> [ 20.770375] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
> connected qmi:00000000e25ddf03 node:7, port:2
> [ 20.771668] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2709 qmi:00000000e25ddf03
> [ 20.776796] ath11k_pci 0000:01:00.0:
> ath11k_qmi_event_server_arrive@2718 qmi:00000000e25ddf03
> fw_ind_register completed.
> [ 20.778021] ath11k_pci 0000:01:00.0: host capability request failed: 1 90
>
>
> Any thoughts and ideas of what might be the cause?
> thanks
Hi,
I would second this question as I have the same issue with IPQ8074+QCN9074.
Note that the multiple debugfs patch has already been applied.
Regards,
Robert
>
> --
> arithdon
>
> --
> ath11k mailing list
> ath11k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath11k
--
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko@sartura.hr
Web: www.sartura.hr
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: ath11k: does qmi support multiple soc
2022-04-18 9:27 ` Robert Marko
@ 2022-04-18 10:13 ` fengbin
0 siblings, 0 replies; 6+ messages in thread
From: fengbin @ 2022-04-18 10:13 UTC (permalink / raw)
To: Robert Marko; +Cc: ath11k
yes, the debugfs patch has been applied.
On Mon, Apr 18, 2022 at 5:28 PM Robert Marko <robert.marko@sartura.hr> wrote:
>
> On Mon, Apr 18, 2022 at 10:37 AM fengbin <arithdon@gmail.com> wrote:
> >
> > Hello,
> > I have qca6390 and qcn9074 both of them works fine individually.
> > However when I install them together errors show up.
> >
> >
> > here is log with only 9074 installed:
> > [ 17.759191] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
> > connected qmi:00000000181299d3 node:7, port:2
> > [ 17.759197] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2709 qmi:00000000181299d3
> > [ 17.760436] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2718 qmi:00000000181299d3
> > fw_ind_register completed.
> > [ 17.761703] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2725 qmi:00000000181299d3
> > fw_ind_register host_cap completed.
> > [ 17.767555] ath11k_pci 0000:01:00.0: chip_id 0x0 chip_family 0x0
> > board_id 0xff soc_id 0xffffffff
> > [ 17.767559] ath11k_pci 0000:01:00.0: fw_version 0x2506844c
> > fw_build_timestamp 2021-07-13 10:24 fw_build_id
> > [ 19.495395] ath11k_pci 0000:01:00.0 wlp1s0: renamed from wlan0
> >
> > and here is log with 6390+9074 and from the log it seems 01:00.01
> > device get same qmi messages twice and thus the host_cap request
> > failed the second time where chipset FW consider the host_cap request
> > is in bad state.
> >
> > [ 19.106915] ath11k_pci 0000:01:00.0: BAR 0: assigned [mem
> > 0x92000000-0x921fffff 64bit]
> > [ 19.106947] ath11k_pci 0000:01:00.0: enabling device (0100 -> 0102)
> > [ 19.107355] ath11k_pci 0000:01:00.0: MSI vectors: 16
> > [ 19.107366] ath11k_pci 0000:01:00.0: qcn9074 hw1.0
> > [ 19.107505] ath11k_pci 0000:01:00.0: mhi controller registered
> > :0000000054128108 mhi_ctrl->index:0 mhi_ctrl->mhi_dev:mhi0
> > [ 20.173172] ath11k_pci 0000:05:00.0: BAR 0: assigned [mem
> > 0x91000000-0x91ffffff 64bit]
> > [ 20.173218] ath11k_pci 0000:05:00.0: enabling device (0100 -> 0102)
> > [ 20.173937] ath11k_pci 0000:05:00.0: MSI vectors: 32
> > [ 20.173959] ath11k_pci 0000:05:00.0: qca6390 hw2.0
> > [ 20.174111] ath11k_pci 0000:05:00.0: mhi controller registered
> > :00000000c33f02d3 mhi_ctrl->index:1 mhi_ctrl->mhi_dev:mhi1
> > [ 20.767399] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
> > connected qmi:00000000e25ddf03 node:7, port:2
> > [ 20.767423] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2709 qmi:00000000e25ddf03
> > [ 20.768739] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2718 qmi:00000000e25ddf03
> > fw_ind_register completed.
> > [ 20.770333] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2725 qmi:00000000e25ddf03
> > fw_ind_register host_cap completed.
> > [ 20.770375] ath11k_pci 0000:01:00.0: qmi wifi fw qmi service
> > connected qmi:00000000e25ddf03 node:7, port:2
> > [ 20.771668] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2709 qmi:00000000e25ddf03
> > [ 20.776796] ath11k_pci 0000:01:00.0:
> > ath11k_qmi_event_server_arrive@2718 qmi:00000000e25ddf03
> > fw_ind_register completed.
> > [ 20.778021] ath11k_pci 0000:01:00.0: host capability request failed: 1 90
> >
> >
> > Any thoughts and ideas of what might be the cause?
> > thanks
>
> Hi,
> I would second this question as I have the same issue with IPQ8074+QCN9074.
> Note that the multiple debugfs patch has already been applied.
>
> Regards,
> Robert
> >
> > --
> > arithdon
> >
> > --
> > ath11k mailing list
> > ath11k@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/ath11k
>
>
>
> --
> Robert Marko
> Staff Embedded Linux Engineer
> Sartura Ltd.
> Lendavska ulica 16a
> 10000 Zagreb, Croatia
> Email: robert.marko@sartura.hr
> Web: www.sartura.hr
--
arithdon
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: ath11k: does qmi support multiple soc
2022-04-18 8:37 ath11k: does qmi support multiple soc fengbin
2022-04-18 9:27 ` Robert Marko
@ 2022-04-22 15:43 ` Jeff Johnson
2022-04-24 15:57 ` Robert Marko
1 sibling, 1 reply; 6+ messages in thread
From: Jeff Johnson @ 2022-04-22 15:43 UTC (permalink / raw)
To: fengbin, ath11k; +Cc: Anilkumar Kolli
On 4/18/2022 1:37 AM, fengbin wrote:
> Hello,
> I have qca6390 and qcn9074 both of them works fine individually.
> However when I install them together errors show up.
This is a known issue. A solution is under development.
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: ath11k: does qmi support multiple soc
2022-04-22 15:43 ` Jeff Johnson
@ 2022-04-24 15:57 ` Robert Marko
2022-09-28 10:20 ` Robert Marko
0 siblings, 1 reply; 6+ messages in thread
From: Robert Marko @ 2022-04-24 15:57 UTC (permalink / raw)
To: Jeff Johnson; +Cc: fengbin, ath11k, Anilkumar Kolli
On Fri, Apr 22, 2022 at 5:47 PM Jeff Johnson <quic_jjohnson@quicinc.com> wrote:
>
> On 4/18/2022 1:37 AM, fengbin wrote:
> > Hello,
> > I have qca6390 and qcn9074 both of them works fine individually.
> > However when I install them together errors show up.
>
> This is a known issue. A solution is under development.
Hi Jeff,
thanks for confirming the issue.
Regards,
Robert
>
> --
> ath11k mailing list
> ath11k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath11k
--
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko@sartura.hr
Web: www.sartura.hr
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: ath11k: does qmi support multiple soc
2022-04-24 15:57 ` Robert Marko
@ 2022-09-28 10:20 ` Robert Marko
0 siblings, 0 replies; 6+ messages in thread
From: Robert Marko @ 2022-09-28 10:20 UTC (permalink / raw)
To: Jeff Johnson; +Cc: fengbin, ath11k, Anilkumar Kolli
On Sun, Apr 24, 2022 at 5:57 PM Robert Marko <robert.marko@sartura.hr> wrote:
>
> On Fri, Apr 22, 2022 at 5:47 PM Jeff Johnson <quic_jjohnson@quicinc.com> wrote:
> >
> > On 4/18/2022 1:37 AM, fengbin wrote:
> > > Hello,
> > > I have qca6390 and qcn9074 both of them works fine individually.
> > > However when I install them together errors show up.
> >
> > This is a known issue. A solution is under development.
Hi,
Any news on this issue?
This is really annoying on boards that use PCI radios for most of the 5GHz band.
Regards,
Robert
>
> Hi Jeff,
> thanks for confirming the issue.
>
> Regards,
> Robert
> >
> > --
> > ath11k mailing list
> > ath11k@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/ath11k
>
>
>
> --
> Robert Marko
> Staff Embedded Linux Engineer
> Sartura Ltd.
> Lendavska ulica 16a
> 10000 Zagreb, Croatia
> Email: robert.marko@sartura.hr
> Web: www.sartura.hr
--
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko@sartura.hr
Web: www.sartura.hr
--
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2022-09-28 10:21 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-04-18 8:37 ath11k: does qmi support multiple soc fengbin
2022-04-18 9:27 ` Robert Marko
2022-04-18 10:13 ` fengbin
2022-04-22 15:43 ` Jeff Johnson
2022-04-24 15:57 ` Robert Marko
2022-09-28 10:20 ` Robert Marko
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.