[U-Boot] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[U-Boot] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[codekipper at gmail.com]

From: Marcus Cooper <codekipper@gmail.com>

The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
---
Changes in v4:
- updated dts to reflex current linux kernel status

Changes in v3:
- Removed incorrect commit author
- Included v1-v2 change info

Changes in v2:
- updated dts to reflex current linux kernel status
---
 arch/arm/dts/Makefile                |   1 +
 arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
 board/sunxi/MAINTAINERS              |   5 +
 configs/beelink_x2_defconfig         |  19 +++
 4 files changed, 241 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
 create mode 100644 configs/beelink_x2_defconfig

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 83058c4452..716108dd2e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-beelink-x2.dtb \
 	sun8i-h3-libretech-all-h3-cc.dtb \
 	sun8i-h3-nanopi-m1.dtb \
 	sun8i-h3-nanopi-m1-plus.dtb \
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts
new file mode 100644
index 0000000000..25540b7694
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -0,0 +1,216 @@
+/*
+ * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Beelink X2";
+	compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &emac;
+		ethernet1 = &sdiowifi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "beelink-x2:blue:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+
+		red {
+			label = "beelink-x2:red:standby";
+			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+		};
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
+
+	sound_spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "On-board SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * Explicitly define the sdio device, so that we can add an ethernet
+	 * alias for it (which e.g. makes u-boot set a mac-address).
+	 */
+	sdiowifi: sdio_wifi at 1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spdif_tx_pins_a>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB VBUS is always on except for the OTG port */
+	status = "okay";
+	usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index bdd1854197..28f2bece40 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -172,6 +172,11 @@ S:	Maintained
 F:	configs/beelink_gs1_defconfig
 F:	arch/arm/dts/sun50i-h6-beelink-gs1.dts
 
+BEELINK X2 BOARD
+M:	Marcus Cooper <codekipper@gmail.com>
+S:	Maintained
+F:	configs/beelink_x2_defconfig
+
 COLOMBUS BOARD
 M:	Maxime Ripard <maxime.ripard@bootlin.com>
 S:	Maintained
diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
new file mode 100644
index 0000000000..6508e470a0
--- /dev/null
+++ b/configs/beelink_x2_defconfig
@@ -0,0 +1,19 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=624
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SPL_I2C_SUPPORT=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SUN8I_EMAC=y
+CONFIG_SY8106A_POWER=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
-- 
2.21.0

[U-Boot] [linux-sunxi] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[Jernej Škrabec]

Hi!

Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekipper at gmail.com napisal(a):
> From: Marcus Cooper <codekipper@gmail.com>
> 
> The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> dual colour LED and an optical S/PDIF connector.
> 
> Signed-off-by: Marcus Cooper <codekipper@gmail.com>
> ---
> Changes in v4:
> - updated dts to reflex current linux kernel status
> 
> Changes in v3:
> - Removed incorrect commit author
> - Included v1-v2 change info
> 
> Changes in v2:
> - updated dts to reflex current linux kernel status
> ---
>  arch/arm/dts/Makefile                |   1 +
>  arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
>  board/sunxi/MAINTAINERS              |   5 +
>  configs/beelink_x2_defconfig         |  19 +++
>  4 files changed, 241 insertions(+)
>  create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
>  create mode 100644 configs/beelink_x2_defconfig
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 83058c4452..716108dd2e 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
>  	sun8i-h2-plus-orangepi-r1.dtb \
>  	sun8i-h2-plus-orangepi-zero.dtb \
>  	sun8i-h3-bananapi-m2-plus.dtb \
> +	sun8i-h3-beelink-x2.dtb \
>  	sun8i-h3-libretech-all-h3-cc.dtb \
>  	sun8i-h3-nanopi-m1.dtb \
>  	sun8i-h3-nanopi-m1-plus.dtb \
> diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> index 0000000000..25540b7694
> --- /dev/null
> +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> @@ -0,0 +1,216 @@
> +/*
> + * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h3.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Beelink X2";
> +	compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &emac;
> +		ethernet1 = &sdiowifi;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		blue {
> +			label = "beelink-x2:blue:pwr";
> +			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* 
PL10 */
> +			default-state = "on";
> +		};
> +
> +		red {
> +			label = "beelink-x2:red:standby";
> +			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 
*/
> +		};
> +	};
> +
> +	wifi_pwrseq: wifi_pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> +	};
> +
> +	sound_spdif {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "On-board SPDIF";
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&spdif>;
> +		};
> +
> +		simple-audio-card,codec {
> +			sound-dai = <&spdif_out>;
> +		};
> +	};
> +
> +	spdif_out: spdif-out {
> +		#sound-dai-cells = <0>;
> +		compatible = "linux,spdif-dit";
> +	};
> +};
> +
> +&de {
> +	status = "okay";
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&emac {
> +	phy-handle = <&int_mii_phy>;
> +	phy-mode = "mii";
> +	allwinner,leds-active-low;
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	status = "okay";
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +&ir {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ir_pins_a>;
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> +	status = "okay";
> +};
> +
> +&mmc1 {
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	/*
> +	 * Explicitly define the sdio device, so that we can add an ethernet
> +	 * alias for it (which e.g. makes u-boot set a mac-address).
> +	 */
> +	sdiowifi: sdio_wifi at 1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc2_8bit_pins>;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <8>;
> +	non-removable;
> +	cap-mmc-hw-reset;
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&reg_usb0_vbus {
> +	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> +	status = "okay";
> +};
> +
> +&spdif {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spdif_tx_pins_a>;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&usb_otg {
> +	dr_mode = "otg";
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	/* USB VBUS is always on except for the OTG port */
> +	status = "okay";
> +	usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> +	usb0_vbus-supply = <&reg_usb0_vbus>;
> +};
> diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> index bdd1854197..28f2bece40 100644
> --- a/board/sunxi/MAINTAINERS
> +++ b/board/sunxi/MAINTAINERS
> @@ -172,6 +172,11 @@ S:	Maintained
>  F:	configs/beelink_gs1_defconfig
>  F:	arch/arm/dts/sun50i-h6-beelink-gs1.dts
> 
> +BEELINK X2 BOARD
> +M:	Marcus Cooper <codekipper@gmail.com>
> +S:	Maintained
> +F:	configs/beelink_x2_defconfig
> +
>  COLOMBUS BOARD
>  M:	Maxime Ripard <maxime.ripard@bootlin.com>
>  S:	Maintained
> diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> new file mode 100644
> index 0000000000..6508e470a0
> --- /dev/null
> +++ b/configs/beelink_x2_defconfig
> @@ -0,0 +1,19 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_SPL=y
> +CONFIG_MACH_SUN8I_H3=y
> +CONFIG_DRAM_CLK=624

Android on my Beelink X2 box sets DRAM clock to 576 MHz, did you check yours?

> +CONFIG_DRAM_ZQ=3881979
> +CONFIG_DRAM_ODT_EN=y
> +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_CONSOLE_MUX=y
> +CONFIG_SPL_I2C_SUPPORT=y
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_SUN8I_EMAC=y
> +CONFIG_SY8106A_POWER=y

I'm pretty sure that my Beelink X2 doesn't have SY8106A regulator. In fact, it 
doesn't have any regulator for CPU voltage (it's fixed). I think you should 
drop this and CONFIG_SPL_I2C_SUPPORT line from defconfig.

I know there are at least two models of Beelink X2 (different wifi), but I think 
both are missing CPU regulator.

Best regards,
Jernej

> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y

[U-Boot] [linux-sunxi] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[Jernej Škrabec]

Hi!

Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekipper at gmail.com napisal(a):
> From: Marcus Cooper <codekipper@gmail.com>
> 
> The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> dual colour LED and an optical S/PDIF connector.
> 
> Signed-off-by: Marcus Cooper <codekipper@gmail.com>
> ---
> Changes in v4:
> - updated dts to reflex current linux kernel status
> 
> Changes in v3:
> - Removed incorrect commit author
> - Included v1-v2 change info
> 
> Changes in v2:
> - updated dts to reflex current linux kernel status
> ---
>  arch/arm/dts/Makefile                |   1 +
>  arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
>  board/sunxi/MAINTAINERS              |   5 +
>  configs/beelink_x2_defconfig         |  19 +++
>  4 files changed, 241 insertions(+)
>  create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
>  create mode 100644 configs/beelink_x2_defconfig
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 83058c4452..716108dd2e 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
>  	sun8i-h2-plus-orangepi-r1.dtb \
>  	sun8i-h2-plus-orangepi-zero.dtb \
>  	sun8i-h3-bananapi-m2-plus.dtb \
> +	sun8i-h3-beelink-x2.dtb \
>  	sun8i-h3-libretech-all-h3-cc.dtb \
>  	sun8i-h3-nanopi-m1.dtb \
>  	sun8i-h3-nanopi-m1-plus.dtb \
> diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> index 0000000000..25540b7694
> --- /dev/null
> +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> @@ -0,0 +1,216 @@
> +/*
> + * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h3.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Beelink X2";
> +	compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &emac;
> +		ethernet1 = &sdiowifi;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		blue {
> +			label = "beelink-x2:blue:pwr";
> +			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* 
PL10 */
> +			default-state = "on";
> +		};
> +
> +		red {
> +			label = "beelink-x2:red:standby";
> +			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 
*/
> +		};
> +	};
> +
> +	wifi_pwrseq: wifi_pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> +	};
> +
> +	sound_spdif {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "On-board SPDIF";
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&spdif>;
> +		};
> +
> +		simple-audio-card,codec {
> +			sound-dai = <&spdif_out>;
> +		};
> +	};
> +
> +	spdif_out: spdif-out {
> +		#sound-dai-cells = <0>;
> +		compatible = "linux,spdif-dit";
> +	};
> +};
> +
> +&de {
> +	status = "okay";
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&emac {
> +	phy-handle = <&int_mii_phy>;
> +	phy-mode = "mii";
> +	allwinner,leds-active-low;
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	status = "okay";
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +&ir {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ir_pins_a>;
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> +	status = "okay";
> +};
> +
> +&mmc1 {
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	/*
> +	 * Explicitly define the sdio device, so that we can add an ethernet
> +	 * alias for it (which e.g. makes u-boot set a mac-address).
> +	 */
> +	sdiowifi: sdio_wifi at 1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc2_8bit_pins>;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <8>;
> +	non-removable;
> +	cap-mmc-hw-reset;
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&reg_usb0_vbus {
> +	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> +	status = "okay";
> +};
> +
> +&spdif {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spdif_tx_pins_a>;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&usb_otg {
> +	dr_mode = "otg";
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	/* USB VBUS is always on except for the OTG port */
> +	status = "okay";
> +	usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> +	usb0_vbus-supply = <&reg_usb0_vbus>;
> +};
> diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> index bdd1854197..28f2bece40 100644
> --- a/board/sunxi/MAINTAINERS
> +++ b/board/sunxi/MAINTAINERS
> @@ -172,6 +172,11 @@ S:	Maintained
>  F:	configs/beelink_gs1_defconfig
>  F:	arch/arm/dts/sun50i-h6-beelink-gs1.dts
> 
> +BEELINK X2 BOARD
> +M:	Marcus Cooper <codekipper@gmail.com>
> +S:	Maintained
> +F:	configs/beelink_x2_defconfig
> +
>  COLOMBUS BOARD
>  M:	Maxime Ripard <maxime.ripard@bootlin.com>
>  S:	Maintained
> diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> new file mode 100644
> index 0000000000..6508e470a0
> --- /dev/null
> +++ b/configs/beelink_x2_defconfig
> @@ -0,0 +1,19 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_SPL=y
> +CONFIG_MACH_SUN8I_H3=y
> +CONFIG_DRAM_CLK=624
> +CONFIG_DRAM_ZQ=3881979
> +CONFIG_DRAM_ODT_EN=y
> +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_CONSOLE_MUX=y
> +CONFIG_SPL_I2C_SUPPORT=y
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_SUN8I_EMAC=y
> +CONFIG_SY8106A_POWER=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y

I think you should add:
CONFIG_SPL_TEXT_BASE=0x60

due to following commit:
http://git.denx.de/?p=u-boot/u-boot-sunxi.git;a=commit;h=f89d6133ee

Best regards,
Jernej

[U-Boot] [linux-sunxi] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[Code Kipper]

On Sun, 26 May 2019 at 08:42, Jernej Å krabec <jernej.skrabec@gmail.com> wrote:
>
> Hi!
>
> Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekipper at gmail.com napisal(a):
> > From: Marcus Cooper <codekipper@gmail.com>
> >
> > The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> > 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> > SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> > dual colour LED and an optical S/PDIF connector.
> >
> > Signed-off-by: Marcus Cooper <codekipper@gmail.com>
> > ---
> > Changes in v4:
> > - updated dts to reflex current linux kernel status
> >
> > Changes in v3:
> > - Removed incorrect commit author
> > - Included v1-v2 change info
> >
> > Changes in v2:
> > - updated dts to reflex current linux kernel status
> > ---
> >  arch/arm/dts/Makefile                |   1 +
> >  arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
> >  board/sunxi/MAINTAINERS              |   5 +
> >  configs/beelink_x2_defconfig         |  19 +++
> >  4 files changed, 241 insertions(+)
> >  create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
> >  create mode 100644 configs/beelink_x2_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 83058c4452..716108dd2e 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
> >       sun8i-h2-plus-orangepi-r1.dtb \
> >       sun8i-h2-plus-orangepi-zero.dtb \
> >       sun8i-h3-bananapi-m2-plus.dtb \
> > +     sun8i-h3-beelink-x2.dtb \
> >       sun8i-h3-libretech-all-h3-cc.dtb \
> >       sun8i-h3-nanopi-m1.dtb \
> >       sun8i-h3-nanopi-m1-plus.dtb \
> > diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> > index 0000000000..25540b7694
> > --- /dev/null
> > +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > @@ -0,0 +1,216 @@
> > +/*
> > + * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
> > + *
> > + * This file is dual-licensed: you can use it either under the terms
> > + * of the GPL or the X11 license, at your option. Note that this dual
> > + * licensing only applies to this file, and not this project as a
> > + * whole.
> > + *
> > + *  a) This file is free software; you can redistribute it and/or
> > + *     modify it under the terms of the GNU General Public License as
> > + *     published by the Free Software Foundation; either version 2 of the
> > + *     License, or (at your option) any later version.
> > + *
> > + *     This file is distributed in the hope that it will be useful,
> > + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + *     GNU General Public License for more details.
> > + *
> > + * Or, alternatively,
> > + *
> > + *  b) Permission is hereby granted, free of charge, to any person
> > + *     obtaining a copy of this software and associated documentation
> > + *     files (the "Software"), to deal in the Software without
> > + *     restriction, including without limitation the rights to use,
> > + *     copy, modify, merge, publish, distribute, sublicense, and/or
> > + *     sell copies of the Software, and to permit persons to whom the
> > + *     Software is furnished to do so, subject to the following
> > + *     conditions:
> > + *
> > + *     The above copyright notice and this permission notice shall be
> > + *     included in all copies or substantial portions of the Software.
> > + *
> > + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > + *     OTHER DEALINGS IN THE SOFTWARE.
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun8i-h3.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > +     model = "Beelink X2";
> > +     compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> > +
> > +     aliases {
> > +             serial0 = &uart0;
> > +             ethernet0 = &emac;
> > +             ethernet1 = &sdiowifi;
> > +     };
> > +
> > +     chosen {
> > +             stdout-path = "serial0:115200n8";
> > +     };
> > +
> > +     connector {
> > +             compatible = "hdmi-connector";
> > +             type = "a";
> > +
> > +             port {
> > +                     hdmi_con_in: endpoint {
> > +                             remote-endpoint = <&hdmi_out_con>;
> > +                     };
> > +             };
> > +     };
> > +
> > +     leds {
> > +             compatible = "gpio-leds";
> > +
> > +             blue {
> > +                     label = "beelink-x2:blue:pwr";
> > +                     gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /*
> PL10 */
> > +                     default-state = "on";
> > +             };
> > +
> > +             red {
> > +                     label = "beelink-x2:red:standby";
> > +                     gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15
> */
> > +             };
> > +     };
> > +
> > +     wifi_pwrseq: wifi_pwrseq {
> > +             compatible = "mmc-pwrseq-simple";
> > +             reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > +     };
> > +
> > +     sound_spdif {
> > +             compatible = "simple-audio-card";
> > +             simple-audio-card,name = "On-board SPDIF";
> > +
> > +             simple-audio-card,cpu {
> > +                     sound-dai = <&spdif>;
> > +             };
> > +
> > +             simple-audio-card,codec {
> > +                     sound-dai = <&spdif_out>;
> > +             };
> > +     };
> > +
> > +     spdif_out: spdif-out {
> > +             #sound-dai-cells = <0>;
> > +             compatible = "linux,spdif-dit";
> > +     };
> > +};
> > +
> > +&de {
> > +     status = "okay";
> > +};
> > +
> > +&ehci0 {
> > +     status = "okay";
> > +};
> > +
> > +&ehci1 {
> > +     status = "okay";
> > +};
> > +
> > +&emac {
> > +     phy-handle = <&int_mii_phy>;
> > +     phy-mode = "mii";
> > +     allwinner,leds-active-low;
> > +     status = "okay";
> > +};
> > +
> > +&hdmi {
> > +     status = "okay";
> > +};
> > +
> > +&hdmi_out {
> > +     hdmi_out_con: endpoint {
> > +             remote-endpoint = <&hdmi_con_in>;
> > +     };
> > +};
> > +
> > +&ir {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&ir_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&mmc0 {
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <4>;
> > +     cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> > +     status = "okay";
> > +};
> > +
> > +&mmc1 {
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <4>;
> > +     non-removable;
> > +     status = "okay";
> > +
> > +     /*
> > +      * Explicitly define the sdio device, so that we can add an ethernet
> > +      * alias for it (which e.g. makes u-boot set a mac-address).
> > +      */
> > +     sdiowifi: sdio_wifi at 1 {
> > +             reg = <1>;
> > +     };
> > +};
> > +
> > +&mmc2 {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&mmc2_8bit_pins>;
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <8>;
> > +     non-removable;
> > +     cap-mmc-hw-reset;
> > +     status = "okay";
> > +};
> > +
> > +&ohci0 {
> > +     status = "okay";
> > +};
> > +
> > +&ohci1 {
> > +     status = "okay";
> > +};
> > +
> > +&reg_usb0_vbus {
> > +     gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > +     status = "okay";
> > +};
> > +
> > +&spdif {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&spdif_tx_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&uart0 {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&uart0_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&usb_otg {
> > +     dr_mode = "otg";
> > +     status = "okay";
> > +};
> > +
> > +&usbphy {
> > +     /* USB VBUS is always on except for the OTG port */
> > +     status = "okay";
> > +     usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> > +     usb0_vbus-supply = <&reg_usb0_vbus>;
> > +};
> > diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> > index bdd1854197..28f2bece40 100644
> > --- a/board/sunxi/MAINTAINERS
> > +++ b/board/sunxi/MAINTAINERS
> > @@ -172,6 +172,11 @@ S:       Maintained
> >  F:   configs/beelink_gs1_defconfig
> >  F:   arch/arm/dts/sun50i-h6-beelink-gs1.dts
> >
> > +BEELINK X2 BOARD
> > +M:   Marcus Cooper <codekipper@gmail.com>
> > +S:   Maintained
> > +F:   configs/beelink_x2_defconfig
> > +
> >  COLOMBUS BOARD
> >  M:   Maxime Ripard <maxime.ripard@bootlin.com>
> >  S:   Maintained
> > diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> > new file mode 100644
> > index 0000000000..6508e470a0
> > --- /dev/null
> > +++ b/configs/beelink_x2_defconfig
> > @@ -0,0 +1,19 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_SPL=y
> > +CONFIG_MACH_SUN8I_H3=y
> > +CONFIG_DRAM_CLK=624
>
> Android on my Beelink X2 box sets DRAM clock to 576 MHz, did you check yours?
>
> > +CONFIG_DRAM_ZQ=3881979
> > +CONFIG_DRAM_ODT_EN=y
> > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > +CONFIG_CONSOLE_MUX=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +# CONFIG_CMD_FLASH is not set
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_SUN8I_EMAC=y
> > +CONFIG_SY8106A_POWER=y
>
> I'm pretty sure that my Beelink X2 doesn't have SY8106A regulator. In fact, it
> doesn't have any regulator for CPU voltage (it's fixed). I think you should
> drop this and CONFIG_SPL_I2C_SUPPORT line from defconfig.
>
> I know there are at least two models of Beelink X2 (different wifi), but I think
> both are missing CPU regulator.
>
> Best regards,
> Jernej

ACK thanks,
CK
>
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
>
>
>
>

[U-Boot] [linux-sunxi] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[Code Kipper]

On Sun, 26 May 2019 at 14:13, Jernej Å krabec <jernej.skrabec@gmail.com> wrote:
>
> Hi!
>
> Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekipper at gmail.com napisal(a):
> > From: Marcus Cooper <codekipper@gmail.com>
> >
> > The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> > 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> > SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> > dual colour LED and an optical S/PDIF connector.
> >
> > Signed-off-by: Marcus Cooper <codekipper@gmail.com>
> > ---
> > Changes in v4:
> > - updated dts to reflex current linux kernel status
> >
> > Changes in v3:
> > - Removed incorrect commit author
> > - Included v1-v2 change info
> >
> > Changes in v2:
> > - updated dts to reflex current linux kernel status
> > ---
> >  arch/arm/dts/Makefile                |   1 +
> >  arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
> >  board/sunxi/MAINTAINERS              |   5 +
> >  configs/beelink_x2_defconfig         |  19 +++
> >  4 files changed, 241 insertions(+)
> >  create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
> >  create mode 100644 configs/beelink_x2_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 83058c4452..716108dd2e 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
> >       sun8i-h2-plus-orangepi-r1.dtb \
> >       sun8i-h2-plus-orangepi-zero.dtb \
> >       sun8i-h3-bananapi-m2-plus.dtb \
> > +     sun8i-h3-beelink-x2.dtb \
> >       sun8i-h3-libretech-all-h3-cc.dtb \
> >       sun8i-h3-nanopi-m1.dtb \
> >       sun8i-h3-nanopi-m1-plus.dtb \
> > diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> > index 0000000000..25540b7694
> > --- /dev/null
> > +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > @@ -0,0 +1,216 @@
> > +/*
> > + * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
> > + *
> > + * This file is dual-licensed: you can use it either under the terms
> > + * of the GPL or the X11 license, at your option. Note that this dual
> > + * licensing only applies to this file, and not this project as a
> > + * whole.
> > + *
> > + *  a) This file is free software; you can redistribute it and/or
> > + *     modify it under the terms of the GNU General Public License as
> > + *     published by the Free Software Foundation; either version 2 of the
> > + *     License, or (at your option) any later version.
> > + *
> > + *     This file is distributed in the hope that it will be useful,
> > + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + *     GNU General Public License for more details.
> > + *
> > + * Or, alternatively,
> > + *
> > + *  b) Permission is hereby granted, free of charge, to any person
> > + *     obtaining a copy of this software and associated documentation
> > + *     files (the "Software"), to deal in the Software without
> > + *     restriction, including without limitation the rights to use,
> > + *     copy, modify, merge, publish, distribute, sublicense, and/or
> > + *     sell copies of the Software, and to permit persons to whom the
> > + *     Software is furnished to do so, subject to the following
> > + *     conditions:
> > + *
> > + *     The above copyright notice and this permission notice shall be
> > + *     included in all copies or substantial portions of the Software.
> > + *
> > + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > + *     OTHER DEALINGS IN THE SOFTWARE.
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun8i-h3.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > +     model = "Beelink X2";
> > +     compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> > +
> > +     aliases {
> > +             serial0 = &uart0;
> > +             ethernet0 = &emac;
> > +             ethernet1 = &sdiowifi;
> > +     };
> > +
> > +     chosen {
> > +             stdout-path = "serial0:115200n8";
> > +     };
> > +
> > +     connector {
> > +             compatible = "hdmi-connector";
> > +             type = "a";
> > +
> > +             port {
> > +                     hdmi_con_in: endpoint {
> > +                             remote-endpoint = <&hdmi_out_con>;
> > +                     };
> > +             };
> > +     };
> > +
> > +     leds {
> > +             compatible = "gpio-leds";
> > +
> > +             blue {
> > +                     label = "beelink-x2:blue:pwr";
> > +                     gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /*
> PL10 */
> > +                     default-state = "on";
> > +             };
> > +
> > +             red {
> > +                     label = "beelink-x2:red:standby";
> > +                     gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15
> */
> > +             };
> > +     };
> > +
> > +     wifi_pwrseq: wifi_pwrseq {
> > +             compatible = "mmc-pwrseq-simple";
> > +             reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > +     };
> > +
> > +     sound_spdif {
> > +             compatible = "simple-audio-card";
> > +             simple-audio-card,name = "On-board SPDIF";
> > +
> > +             simple-audio-card,cpu {
> > +                     sound-dai = <&spdif>;
> > +             };
> > +
> > +             simple-audio-card,codec {
> > +                     sound-dai = <&spdif_out>;
> > +             };
> > +     };
> > +
> > +     spdif_out: spdif-out {
> > +             #sound-dai-cells = <0>;
> > +             compatible = "linux,spdif-dit";
> > +     };
> > +};
> > +
> > +&de {
> > +     status = "okay";
> > +};
> > +
> > +&ehci0 {
> > +     status = "okay";
> > +};
> > +
> > +&ehci1 {
> > +     status = "okay";
> > +};
> > +
> > +&emac {
> > +     phy-handle = <&int_mii_phy>;
> > +     phy-mode = "mii";
> > +     allwinner,leds-active-low;
> > +     status = "okay";
> > +};
> > +
> > +&hdmi {
> > +     status = "okay";
> > +};
> > +
> > +&hdmi_out {
> > +     hdmi_out_con: endpoint {
> > +             remote-endpoint = <&hdmi_con_in>;
> > +     };
> > +};
> > +
> > +&ir {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&ir_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&mmc0 {
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <4>;
> > +     cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> > +     status = "okay";
> > +};
> > +
> > +&mmc1 {
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <4>;
> > +     non-removable;
> > +     status = "okay";
> > +
> > +     /*
> > +      * Explicitly define the sdio device, so that we can add an ethernet
> > +      * alias for it (which e.g. makes u-boot set a mac-address).
> > +      */
> > +     sdiowifi: sdio_wifi at 1 {
> > +             reg = <1>;
> > +     };
> > +};
> > +
> > +&mmc2 {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&mmc2_8bit_pins>;
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <8>;
> > +     non-removable;
> > +     cap-mmc-hw-reset;
> > +     status = "okay";
> > +};
> > +
> > +&ohci0 {
> > +     status = "okay";
> > +};
> > +
> > +&ohci1 {
> > +     status = "okay";
> > +};
> > +
> > +&reg_usb0_vbus {
> > +     gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > +     status = "okay";
> > +};
> > +
> > +&spdif {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&spdif_tx_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&uart0 {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&uart0_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&usb_otg {
> > +     dr_mode = "otg";
> > +     status = "okay";
> > +};
> > +
> > +&usbphy {
> > +     /* USB VBUS is always on except for the OTG port */
> > +     status = "okay";
> > +     usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> > +     usb0_vbus-supply = <&reg_usb0_vbus>;
> > +};
> > diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> > index bdd1854197..28f2bece40 100644
> > --- a/board/sunxi/MAINTAINERS
> > +++ b/board/sunxi/MAINTAINERS
> > @@ -172,6 +172,11 @@ S:       Maintained
> >  F:   configs/beelink_gs1_defconfig
> >  F:   arch/arm/dts/sun50i-h6-beelink-gs1.dts
> >
> > +BEELINK X2 BOARD
> > +M:   Marcus Cooper <codekipper@gmail.com>
> > +S:   Maintained
> > +F:   configs/beelink_x2_defconfig
> > +
> >  COLOMBUS BOARD
> >  M:   Maxime Ripard <maxime.ripard@bootlin.com>
> >  S:   Maintained
> > diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> > new file mode 100644
> > index 0000000000..6508e470a0
> > --- /dev/null
> > +++ b/configs/beelink_x2_defconfig
> > @@ -0,0 +1,19 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_SPL=y
> > +CONFIG_MACH_SUN8I_H3=y
> > +CONFIG_DRAM_CLK=624
> > +CONFIG_DRAM_ZQ=3881979
> > +CONFIG_DRAM_ODT_EN=y
> > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > +CONFIG_CONSOLE_MUX=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +# CONFIG_CMD_FLASH is not set
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_SUN8I_EMAC=y
> > +CONFIG_SY8106A_POWER=y
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
>
> I think you should add:
> CONFIG_SPL_TEXT_BASE=0x60
>
> due to following commit:
> http://git.denx.de/?p=u-boot/u-boot-sunxi.git;a=commit;h=f89d6133ee
ACK, arrgghh I thought the sunxi-next branch was misbehaving. Now
boots ontop of master,
CK
>
> Best regards,
> Jernej
>
>
>

[U-Boot] [linux-sunxi] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

[Maxime Ripard]

On Sun, May 26, 2019 at 04:52:32PM +0200, Code Kipper wrote:
> On Sun, 26 May 2019 at 14:13, Jernej Å krabec <jernej.skrabec@gmail.com> wrote:
> >
> > Hi!
> >
> > Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekipper at gmail.com napisal(a):
> > > From: Marcus Cooper <codekipper@gmail.com>
> > >
> > > The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> > > 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> > > SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> > > dual colour LED and an optical S/PDIF connector.
> > >
> > > Signed-off-by: Marcus Cooper <codekipper@gmail.com>
> > > ---
> > > Changes in v4:
> > > - updated dts to reflex current linux kernel status
> > >
> > > Changes in v3:
> > > - Removed incorrect commit author
> > > - Included v1-v2 change info
> > >
> > > Changes in v2:
> > > - updated dts to reflex current linux kernel status
> > > ---
> > >  arch/arm/dts/Makefile                |   1 +
> > >  arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
> > >  board/sunxi/MAINTAINERS              |   5 +
> > >  configs/beelink_x2_defconfig         |  19 +++
> > >  4 files changed, 241 insertions(+)
> > >  create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
> > >  create mode 100644 configs/beelink_x2_defconfig
> > >
> > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > > index 83058c4452..716108dd2e 100644
> > > --- a/arch/arm/dts/Makefile
> > > +++ b/arch/arm/dts/Makefile
> > > @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
> > >       sun8i-h2-plus-orangepi-r1.dtb \
> > >       sun8i-h2-plus-orangepi-zero.dtb \
> > >       sun8i-h3-bananapi-m2-plus.dtb \
> > > +     sun8i-h3-beelink-x2.dtb \
> > >       sun8i-h3-libretech-all-h3-cc.dtb \
> > >       sun8i-h3-nanopi-m1.dtb \
> > >       sun8i-h3-nanopi-m1-plus.dtb \
> > > diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > > b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> > > index 0000000000..25540b7694
> > > --- /dev/null
> > > +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > > @@ -0,0 +1,216 @@
> > > +/*
> > > + * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
> > > + *
> > > + * This file is dual-licensed: you can use it either under the terms
> > > + * of the GPL or the X11 license, at your option. Note that this dual
> > > + * licensing only applies to this file, and not this project as a
> > > + * whole.
> > > + *
> > > + *  a) This file is free software; you can redistribute it and/or
> > > + *     modify it under the terms of the GNU General Public License as
> > > + *     published by the Free Software Foundation; either version 2 of the
> > > + *     License, or (at your option) any later version.
> > > + *
> > > + *     This file is distributed in the hope that it will be useful,
> > > + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > > + *     GNU General Public License for more details.
> > > + *
> > > + * Or, alternatively,
> > > + *
> > > + *  b) Permission is hereby granted, free of charge, to any person
> > > + *     obtaining a copy of this software and associated documentation
> > > + *     files (the "Software"), to deal in the Software without
> > > + *     restriction, including without limitation the rights to use,
> > > + *     copy, modify, merge, publish, distribute, sublicense, and/or
> > > + *     sell copies of the Software, and to permit persons to whom the
> > > + *     Software is furnished to do so, subject to the following
> > > + *     conditions:
> > > + *
> > > + *     The above copyright notice and this permission notice shall be
> > > + *     included in all copies or substantial portions of the Software.
> > > + *
> > > + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > > + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > > + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > > + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > > + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > > + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > > + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > > + *     OTHER DEALINGS IN THE SOFTWARE.
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "sun8i-h3.dtsi"
> > > +#include "sunxi-common-regulators.dtsi"
> > > +
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +#include <dt-bindings/input/input.h>
> > > +
> > > +/ {
> > > +     model = "Beelink X2";
> > > +     compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> > > +
> > > +     aliases {
> > > +             serial0 = &uart0;
> > > +             ethernet0 = &emac;
> > > +             ethernet1 = &sdiowifi;
> > > +     };
> > > +
> > > +     chosen {
> > > +             stdout-path = "serial0:115200n8";
> > > +     };
> > > +
> > > +     connector {
> > > +             compatible = "hdmi-connector";
> > > +             type = "a";
> > > +
> > > +             port {
> > > +                     hdmi_con_in: endpoint {
> > > +                             remote-endpoint = <&hdmi_out_con>;
> > > +                     };
> > > +             };
> > > +     };
> > > +
> > > +     leds {
> > > +             compatible = "gpio-leds";
> > > +
> > > +             blue {
> > > +                     label = "beelink-x2:blue:pwr";
> > > +                     gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /*
> > PL10 */
> > > +                     default-state = "on";
> > > +             };
> > > +
> > > +             red {
> > > +                     label = "beelink-x2:red:standby";
> > > +                     gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15
> > */
> > > +             };
> > > +     };
> > > +
> > > +     wifi_pwrseq: wifi_pwrseq {
> > > +             compatible = "mmc-pwrseq-simple";
> > > +             reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > > +     };
> > > +
> > > +     sound_spdif {
> > > +             compatible = "simple-audio-card";
> > > +             simple-audio-card,name = "On-board SPDIF";
> > > +
> > > +             simple-audio-card,cpu {
> > > +                     sound-dai = <&spdif>;
> > > +             };
> > > +
> > > +             simple-audio-card,codec {
> > > +                     sound-dai = <&spdif_out>;
> > > +             };
> > > +     };
> > > +
> > > +     spdif_out: spdif-out {
> > > +             #sound-dai-cells = <0>;
> > > +             compatible = "linux,spdif-dit";
> > > +     };
> > > +};
> > > +
> > > +&de {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&ehci0 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&ehci1 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&emac {
> > > +     phy-handle = <&int_mii_phy>;
> > > +     phy-mode = "mii";
> > > +     allwinner,leds-active-low;
> > > +     status = "okay";
> > > +};
> > > +
> > > +&hdmi {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&hdmi_out {
> > > +     hdmi_out_con: endpoint {
> > > +             remote-endpoint = <&hdmi_con_in>;
> > > +     };
> > > +};
> > > +
> > > +&ir {
> > > +     pinctrl-names = "default";
> > > +     pinctrl-0 = <&ir_pins_a>;
> > > +     status = "okay";
> > > +};
> > > +
> > > +&mmc0 {
> > > +     vmmc-supply = <&reg_vcc3v3>;
> > > +     bus-width = <4>;
> > > +     cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> > > +     status = "okay";
> > > +};
> > > +
> > > +&mmc1 {
> > > +     vmmc-supply = <&reg_vcc3v3>;
> > > +     bus-width = <4>;
> > > +     non-removable;
> > > +     status = "okay";
> > > +
> > > +     /*
> > > +      * Explicitly define the sdio device, so that we can add an ethernet
> > > +      * alias for it (which e.g. makes u-boot set a mac-address).
> > > +      */
> > > +     sdiowifi: sdio_wifi at 1 {
> > > +             reg = <1>;
> > > +     };
> > > +};
> > > +
> > > +&mmc2 {
> > > +     pinctrl-names = "default";
> > > +     pinctrl-0 = <&mmc2_8bit_pins>;
> > > +     vmmc-supply = <&reg_vcc3v3>;
> > > +     bus-width = <8>;
> > > +     non-removable;
> > > +     cap-mmc-hw-reset;
> > > +     status = "okay";
> > > +};
> > > +
> > > +&ohci0 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&ohci1 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&reg_usb0_vbus {
> > > +     gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > > +     status = "okay";
> > > +};
> > > +
> > > +&spdif {
> > > +     pinctrl-names = "default";
> > > +     pinctrl-0 = <&spdif_tx_pins_a>;
> > > +     status = "okay";
> > > +};
> > > +
> > > +&uart0 {
> > > +     pinctrl-names = "default";
> > > +     pinctrl-0 = <&uart0_pins_a>;
> > > +     status = "okay";
> > > +};
> > > +
> > > +&usb_otg {
> > > +     dr_mode = "otg";
> > > +     status = "okay";
> > > +};
> > > +
> > > +&usbphy {
> > > +     /* USB VBUS is always on except for the OTG port */
> > > +     status = "okay";
> > > +     usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> > > +     usb0_vbus-supply = <&reg_usb0_vbus>;
> > > +};
> > > diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> > > index bdd1854197..28f2bece40 100644
> > > --- a/board/sunxi/MAINTAINERS
> > > +++ b/board/sunxi/MAINTAINERS
> > > @@ -172,6 +172,11 @@ S:       Maintained
> > >  F:   configs/beelink_gs1_defconfig
> > >  F:   arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > >
> > > +BEELINK X2 BOARD
> > > +M:   Marcus Cooper <codekipper@gmail.com>
> > > +S:   Maintained
> > > +F:   configs/beelink_x2_defconfig
> > > +
> > >  COLOMBUS BOARD
> > >  M:   Maxime Ripard <maxime.ripard@bootlin.com>
> > >  S:   Maintained
> > > diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> > > new file mode 100644
> > > index 0000000000..6508e470a0
> > > --- /dev/null
> > > +++ b/configs/beelink_x2_defconfig
> > > @@ -0,0 +1,19 @@
> > > +CONFIG_ARM=y
> > > +CONFIG_ARCH_SUNXI=y
> > > +CONFIG_SPL=y
> > > +CONFIG_MACH_SUN8I_H3=y
> > > +CONFIG_DRAM_CLK=624
> > > +CONFIG_DRAM_ZQ=3881979
> > > +CONFIG_DRAM_ODT_EN=y
> > > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> > > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > > +CONFIG_CONSOLE_MUX=y
> > > +CONFIG_SPL_I2C_SUPPORT=y
> > > +# CONFIG_CMD_FLASH is not set
> > > +# CONFIG_SPL_DOS_PARTITION is not set
> > > +# CONFIG_SPL_EFI_PARTITION is not set
> > > +CONFIG_SUN8I_EMAC=y
> > > +CONFIG_SY8106A_POWER=y
> > > +CONFIG_USB_EHCI_HCD=y
> > > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
> >
> > I think you should add:
> > CONFIG_SPL_TEXT_BASE=0x60
> >
> > due to following commit:
> > http://git.denx.de/?p=u-boot/u-boot-sunxi.git;a=commit;h=f89d6133ee
> ACK, arrgghh I thought the sunxi-next branch was misbehaving. Now
> boots ontop of master,

Can we make that a default in Kconfig instead of having to put it in
pretty much every defconfig?

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190526/a6d0d883/attachment.sig>