* git repo with Redpine changes
@ 2017-05-17 8:11 Alexey Brodkin
[not found] ` <CAEhWJFkVe1C9jtxH9zeeMeJiAs86sJGOKSoqMku0qRqNAQujxg@mail.gmail.com>
0 siblings, 1 reply; 9+ messages in thread
From: Alexey Brodkin @ 2017-05-17 8:11 UTC (permalink / raw)
To: prameela.j04cs, amit.karwar; +Cc: linux-wireless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^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: git repo with Redpine changes
[not found] ` <CAEhWJFkVe1C9jtxH9zeeMeJiAs86sJGOKSoqMku0qRqNAQujxg@mail.gmail.com>
@ 2017-05-23 17:26 ` Alexey Brodkin
0 siblings, 0 replies; 9+ messages in thread
From: Alexey Brodkin @ 2017-05-23 17:26 UTC (permalink / raw)
To: amit.karwar; +Cc: linux-wireless, prameela.j04cs, linux-snps-arc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^ permalink raw reply [flat|nested] 9+ messages in thread
* git repo with Redpine changes
@ 2017-05-23 17:26 ` Alexey Brodkin
0 siblings, 0 replies; 9+ messages in thread
From: Alexey Brodkin @ 2017-05-23 17:26 UTC (permalink / raw)
To: linux-snps-arc
Hi Amit!
On Tue, 2017-05-23@17:00 +0530, amit karwar wrote:
> On Wed, May 17, 2017 at 1:41 PM, Alexey Brodkin
> <Alexey.Brodkin@synopsys.com> wrote:
> >
> > Hello Amitkumar, Prameela,
> >
> > I was lucky enough to get hold of RS9113 Evaluation Kit and now I'm trying
> > to get it working with my board via USB and SDIO interfaces but seeing issues here and there:
> > ?1) In case of SDIO I see this on interface up with vanilla 4.11.1 kernel:
> > ----------------------->8--------------------
> > # ifconfig wlan0 up
> > rsi_91x: Sending RX filter frame
> > rsi_91x: rsi_core_qos_processor: Queue number = 4
> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
> > rsi_91x: rsi_set_vap_capabilities: Sending VAP capabilities frame
> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 0, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 1, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 2, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
> > # rsi_91x: rsi_mac80211_conf_tx: Conf queue 3, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
> > rsi_91x: rsi_channel_change: Set channel: 2412 MHz type: 416 channel_no 1
> > rsi_91x: rsi_set_channel: Sending scan req frame
> > rsi_91x: rsi_mac80211_config: Configuring Power
> > rsi_91x: rsi_config_power: Set tx power: 20 dBM
> > rsi_91x: rsi_send_radio_params_update: Sending Radio Params update frame
> > rsi_91x: rsi_core_qos_processor: Queue number = 4
> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
> > rsi_91x: Pkt pending interrupt
> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 0, Msg Type:????1
> > rsi_91x: rsi_handle_ta_confirm_type: Invalid TA confirm pkt received
> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
> > rsi_91x: rsi_core_qos_processor: Queue number = 4
> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
> > rsi_91x: rsi_core_qos_processor: Queue number = 4
> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
> > rsi_91x: Pkt pending interrupt
> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 0, Msg Type:????1
> > rsi_91x: rsi_handle_ta_confirm_type: Invalid TA confirm pkt received
> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
> > rsi_91x: Pkt pending interrupt
> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 321, Msg Type:????2
> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
> > rsi_91x: rsi_core_qos_processor: Queue number = 255
> > rsi_91x: rsi_core_qos_processor: No More Pkt
> > rsi_91x: rsi_interrupt_handler: Intr_status = c 8 4
> > rsi_91x: Pkt pending interrupt
> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 299, Msg Type:????2
> > rsi_91x: rsi_interrupt_handler: ==> FIRMWARE Assert <==
Any hint on what's wrong here?
Note firmware was successfully loaded on probe a bit earlier.
And here I used a firmware blob from linux-firmware git repo,
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/rsi_91x.fw
> > rsi_91x: rsi_interrupt_handler: Firmware Status is 0x65
> > rsi_91x: rsi_core_qos_processor: Queue number = 255
> > rsi_91x: rsi_core_qos_processor: No More Pkt
> > ----------------------->8--------------------
> >
> > and you recent patch series for nwe firmware loading I see something a bit
> > different:
> > ----------------------->8--------------------
> > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz, actual 25000000HZ div = 1)
> > mmc0: new SDIO card at address fffd
> > rsi_91x: rsi_probe: Init function called
> > rsi_91x: rsi_init_sdio_interface: Enabled the interface
> > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
> > rsi_91x: rsi_setblocklength: Setting the block length
> > rsi_91x: rsi_setblocklength: Operational blk length is 256
> > rsi_91x: rsi_init_sdio_interface: Setup card succesfully
> > rsi_91x: rsi_init_sdio_slave_regs: Initialzing SDIO read start level
> > rsi_91x: rsi_init_sdio_slave_regs: Initialzing FIFO ctrl registers
> > rsi_91x: rsi_sdio_master_access_msword: MASTER_ACCESS_MSBYTE:0x5
> > rsi_91x: rsi_sdio_master_access_msword:MASTER_ACCESS_LSBYTE:0x41
> > rsi_91x: rsi_sdio_read_register_multiple: Synch Cmd53 read failed
>
> Looks like sdio_readsb() failed for some reason on your platform.
> We expect firmware loading to be successful with recent patch series.
Hm, that's interesting why stuff used to work before that patch series.
At least as you might see from above I got much further with vanilla 4.11 kernel.
BTW where may I find new firmware blob which is mentioned in on of the patches ("rs9113_wlan_qspi.rps")?
> > rsi_91x: rsi_sdio_master_reg_read: AHB register read failed
> > rsi_91x: rsi_load_firmware: REGOUT read failed
> > rsi_91x: rsi_hal_device_init: Failed to load TA instructions
> > rsi_91x: rsi_probe: Failed in device init
> > rsi_91x: rsi_91x_deinit: Performing deinit os ops
> > rsi_91x: rsi_core_qos_processor: Queue number = 255
> > rsi_91x: rsi_core_qos_processor: No More Pkt
> > rsi_91x: rsi_probe: Failed in probe...Exiting
> > RSI-SDIO WLAN: probe of mmc0:fffd:1 failed with error 1
> > ----------------------->8--------------------
> >
> > ?2) In case of USB I just see:
> > ----------------------->8--------------------
> > usb 1-1: new high-speed USB device number 6 using ehci-platform
> > usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 255, changing to 11
> > usb 1-1: New USB device found, idVendor=1618, idProduct=9113
> > usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> > usb 1-1: Product: Wireless USB-CDC Network Module
> > usb 1-1: Manufacturer: Redpine Signals, Inc.
> > cdc_acm 1-1:1.0: ttyACM0: USB ACM device
> > ----------------------->8--------------------
> >
> > I noticed that there're quite some patches floating on linux-wireless mailing list which
> > were not yet merged in upstream kernel (even in linux-next or wireless-testing).
> >
> > So at this point I'm not really sure what could be a safe baseline for my experiments:
> > ?- if existing vanilla say 4.11 kernel is good enough and things that doesn't work are caused
> > ???by other problems not related to Redpine module (that would be strange because both USB abd SD-card
> > ???slot are proven to work pretty well with other devices)
> > ?- if I need an arbitrary set of patches to get things up and running etc
> >
> > That said if there's a public git repo which contains everything required for Redpine module to
> > work [preferably based on the latest kernel sources] I'd like to get a reference to it.
> >
> > Any hints here are much appreciated.
>
> We don't have a public git repo maintained. We have 2 patchsets ready
> for submission. We are working on code cleanup for other pending
> changes. I would suggest you to wait till these patches are posted.
Ok, will do. But please add me in Cc list in your upcoming patches as I'm very interested
in getting Redpine module working on our new board and will be happy to review them as well as test on
my platform.
BTW I'm wondering what platform you use for development as a host?
I'm wondering if the reason for my failure mentioned above might be in different
host CPU architecture or SD-card controller vendor or settings.
-Alexey
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: git repo with Redpine changes
2017-05-23 17:26 ` Alexey Brodkin
@ 2017-06-01 13:54 ` amit karwar
-1 siblings, 0 replies; 9+ messages in thread
From: amit karwar @ 2017-06-01 13:54 UTC (permalink / raw)
To: Alexey Brodkin
Cc: amit.karwar, linux-wireless, prameela.j04cs, linux-snps-arc
On Tue, May 23, 2017 at 10:56 PM, Alexey Brodkin
<Alexey.Brodkin@synopsys.com> wrote:
> Hi Amit!
>
> On Tue, 2017-05-23 at 17:00 +0530, amit karwar wrote:
>> On Wed, May 17, 2017 at 1:41 PM, Alexey Brodkin
>> <Alexey.Brodkin@synopsys.com> wrote:
>> >
>> > Hello Amitkumar, Prameela,
>> >
>> > I was lucky enough to get hold of RS9113 Evaluation Kit and now I'm trying
>> > to get it working with my board via USB and SDIO interfaces but seeing issues here and there:
>> > 1) In case of SDIO I see this on interface up with vanilla 4.11.1 kernel:
>> > ----------------------->8--------------------
>> > # ifconfig wlan0 up
>> > rsi_91x: Sending RX filter frame
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_set_vap_capabilities: Sending VAP capabilities frame
>> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 0, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 1, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 2, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > # rsi_91x: rsi_mac80211_conf_tx: Conf queue 3, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > rsi_91x: rsi_channel_change: Set channel: 2412 MHz type: 416 channel_no 1
>> > rsi_91x: rsi_set_channel: Sending scan req frame
>> > rsi_91x: rsi_mac80211_config: Configuring Power
>> > rsi_91x: rsi_config_power: Set tx power: 20 dBM
>> > rsi_91x: rsi_send_radio_params_update: Sending Radio Params update frame
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 0, Msg Type: 1
>> > rsi_91x: rsi_handle_ta_confirm_type: Invalid TA confirm pkt received
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 0, Msg Type: 1
>> > rsi_91x: rsi_handle_ta_confirm_type: Invalid TA confirm pkt received
>> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 321, Msg Type: 2
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_core_qos_processor: Queue number = 255
>> > rsi_91x: rsi_core_qos_processor: No More Pkt
>> > rsi_91x: rsi_interrupt_handler: Intr_status = c 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 299, Msg Type: 2
>> > rsi_91x: rsi_interrupt_handler: ==> FIRMWARE Assert <==
>
> Any hint on what's wrong here?
>
> Note firmware was successfully loaded on probe a bit earlier.
> And here I used a firmware blob from linux-firmware git repo,
> https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/rsi_91x.fw
>
>> > rsi_91x: rsi_interrupt_handler: Firmware Status is 0x65
>> > rsi_91x: rsi_core_qos_processor: Queue number = 255
>> > rsi_91x: rsi_core_qos_processor: No More Pkt
>> > ----------------------->8--------------------
>> >
>> > and you recent patch series for nwe firmware loading I see something a bit
>> > different:
>> > ----------------------->8--------------------
>> > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz, actual 25000000HZ div = 1)
>> > mmc0: new SDIO card at address fffd
>> > rsi_91x: rsi_probe: Init function called
>> > rsi_91x: rsi_init_sdio_interface: Enabled the interface
>> > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
>> > rsi_91x: rsi_setblocklength: Setting the block length
>> > rsi_91x: rsi_setblocklength: Operational blk length is 256
>> > rsi_91x: rsi_init_sdio_interface: Setup card succesfully
>> > rsi_91x: rsi_init_sdio_slave_regs: Initialzing SDIO read start level
>> > rsi_91x: rsi_init_sdio_slave_regs: Initialzing FIFO ctrl registers
>> > rsi_91x: rsi_sdio_master_access_msword: MASTER_ACCESS_MSBYTE:0x5
>> > rsi_91x: rsi_sdio_master_access_msword:MASTER_ACCESS_LSBYTE:0x41
>> > rsi_91x: rsi_sdio_read_register_multiple: Synch Cmd53 read failed
>>
>> Looks like sdio_readsb() failed for some reason on your platform.
>> We expect firmware loading to be successful with recent patch series.
>
> Hm, that's interesting why stuff used to work before that patch series.
> At least as you might see from above I got much further with vanilla 4.11 kernel.
>
> BTW where may I find new firmware blob which is mentioned in on of the patches ("rs9113_wlan_qspi.rps")?
I have posted a firmware image for new firmware loading mechanism to
community. There are some patches for SDIO specific driver
enhancements and fixes. I am sending them in couple of days. With
those patches you will be able to see wireless interface bring up,
connection in open network and data path working.
>
>> > rsi_91x: rsi_sdio_master_reg_read: AHB register read failed
>> > rsi_91x: rsi_load_firmware: REGOUT read failed
>> > rsi_91x: rsi_hal_device_init: Failed to load TA instructions
>> > rsi_91x: rsi_probe: Failed in device init
>> > rsi_91x: rsi_91x_deinit: Performing deinit os ops
>> > rsi_91x: rsi_core_qos_processor: Queue number = 255
>> > rsi_91x: rsi_core_qos_processor: No More Pkt
>> > rsi_91x: rsi_probe: Failed in probe...Exiting
>> > RSI-SDIO WLAN: probe of mmc0:fffd:1 failed with error 1
>> > ----------------------->8--------------------
>> >
>> > 2) In case of USB I just see:
>> > ----------------------->8--------------------
>> > usb 1-1: new high-speed USB device number 6 using ehci-platform
>> > usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 255, changing to 11
>> > usb 1-1: New USB device found, idVendor=1618, idProduct=9113
>> > usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>> > usb 1-1: Product: Wireless USB-CDC Network Module
>> > usb 1-1: Manufacturer: Redpine Signals, Inc.
>> > cdc_acm 1-1:1.0: ttyACM0: USB ACM device
>> > ----------------------->8--------------------
>> >
>> > I noticed that there're quite some patches floating on linux-wireless mailing list which
>> > were not yet merged in upstream kernel (even in linux-next or wireless-testing).
>> >
>> > So at this point I'm not really sure what could be a safe baseline for my experiments:
>> > - if existing vanilla say 4.11 kernel is good enough and things that doesn't work are caused
>> > by other problems not related to Redpine module (that would be strange because both USB abd SD-card
>> > slot are proven to work pretty well with other devices)
>> > - if I need an arbitrary set of patches to get things up and running etc
>> >
>> > That said if there's a public git repo which contains everything required for Redpine module to
>> > work [preferably based on the latest kernel sources] I'd like to get a reference to it.
>> >
>> > Any hints here are much appreciated.
>>
>> We don't have a public git repo maintained. We have 2 patchsets ready
>> for submission. We are working on code cleanup for other pending
>> changes. I would suggest you to wait till these patches are posted.
>
> Ok, will do. But please add me in Cc list in your upcoming patches as I'm very interested
> in getting Redpine module working on our new board and will be happy to review them as well as test on
> my platform.
>
Sure. I will add you in CC for those patches.
Regards,
Amitkumar Karwar
^ permalink raw reply [flat|nested] 9+ messages in thread
* git repo with Redpine changes
@ 2017-06-01 13:54 ` amit karwar
0 siblings, 0 replies; 9+ messages in thread
From: amit karwar @ 2017-06-01 13:54 UTC (permalink / raw)
To: linux-snps-arc
On Tue, May 23, 2017 at 10:56 PM, Alexey Brodkin
<Alexey.Brodkin@synopsys.com> wrote:
> Hi Amit!
>
> On Tue, 2017-05-23@17:00 +0530, amit karwar wrote:
>> On Wed, May 17, 2017 at 1:41 PM, Alexey Brodkin
>> <Alexey.Brodkin@synopsys.com> wrote:
>> >
>> > Hello Amitkumar, Prameela,
>> >
>> > I was lucky enough to get hold of RS9113 Evaluation Kit and now I'm trying
>> > to get it working with my board via USB and SDIO interfaces but seeing issues here and there:
>> > 1) In case of SDIO I see this on interface up with vanilla 4.11.1 kernel:
>> > ----------------------->8--------------------
>> > # ifconfig wlan0 up
>> > rsi_91x: Sending RX filter frame
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_set_vap_capabilities: Sending VAP capabilities frame
>> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 0, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 1, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > rsi_91x: rsi_mac80211_conf_tx: Conf queue 2, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > # rsi_91x: rsi_mac80211_conf_tx: Conf queue 3, aifs: 2, cwmin: 15 cwmax: 1023, txop: 0
>> > rsi_91x: rsi_channel_change: Set channel: 2412 MHz type: 416 channel_no 1
>> > rsi_91x: rsi_set_channel: Sending scan req frame
>> > rsi_91x: rsi_mac80211_config: Configuring Power
>> > rsi_91x: rsi_config_power: Set tx power: 20 dBM
>> > rsi_91x: rsi_send_radio_params_update: Sending Radio Params update frame
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 0, Msg Type: 1
>> > rsi_91x: rsi_handle_ta_confirm_type: Invalid TA confirm pkt received
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_core_qos_processor: Queue number = 4
>> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 0, Msg Type: 1
>> > rsi_91x: rsi_handle_ta_confirm_type: Invalid TA confirm pkt received
>> > rsi_91x: rsi_interrupt_handler: Intr_status = 8 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 321, Msg Type: 2
>> > rsi_91x: rsi_sdio_host_intf_write_pkt: Successfully written onto card
>> > rsi_91x: rsi_core_qos_processor: Queue number = 255
>> > rsi_91x: rsi_core_qos_processor: No More Pkt
>> > rsi_91x: rsi_interrupt_handler: Intr_status = c 8 4
>> > rsi_91x: Pkt pending interrupt
>> > rsi_91x: rsi_mgmt_pkt_recv: Msg Len: 299, Msg Type: 2
>> > rsi_91x: rsi_interrupt_handler: ==> FIRMWARE Assert <==
>
> Any hint on what's wrong here?
>
> Note firmware was successfully loaded on probe a bit earlier.
> And here I used a firmware blob from linux-firmware git repo,
> https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/rsi_91x.fw
>
>> > rsi_91x: rsi_interrupt_handler: Firmware Status is 0x65
>> > rsi_91x: rsi_core_qos_processor: Queue number = 255
>> > rsi_91x: rsi_core_qos_processor: No More Pkt
>> > ----------------------->8--------------------
>> >
>> > and you recent patch series for nwe firmware loading I see something a bit
>> > different:
>> > ----------------------->8--------------------
>> > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz, actual 25000000HZ div = 1)
>> > mmc0: new SDIO card at address fffd
>> > rsi_91x: rsi_probe: Init function called
>> > rsi_91x: rsi_init_sdio_interface: Enabled the interface
>> > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
>> > rsi_91x: rsi_setblocklength: Setting the block length
>> > rsi_91x: rsi_setblocklength: Operational blk length is 256
>> > rsi_91x: rsi_init_sdio_interface: Setup card succesfully
>> > rsi_91x: rsi_init_sdio_slave_regs: Initialzing SDIO read start level
>> > rsi_91x: rsi_init_sdio_slave_regs: Initialzing FIFO ctrl registers
>> > rsi_91x: rsi_sdio_master_access_msword: MASTER_ACCESS_MSBYTE:0x5
>> > rsi_91x: rsi_sdio_master_access_msword:MASTER_ACCESS_LSBYTE:0x41
>> > rsi_91x: rsi_sdio_read_register_multiple: Synch Cmd53 read failed
>>
>> Looks like sdio_readsb() failed for some reason on your platform.
>> We expect firmware loading to be successful with recent patch series.
>
> Hm, that's interesting why stuff used to work before that patch series.
> At least as you might see from above I got much further with vanilla 4.11 kernel.
>
> BTW where may I find new firmware blob which is mentioned in on of the patches ("rs9113_wlan_qspi.rps")?
I have posted a firmware image for new firmware loading mechanism to
community. There are some patches for SDIO specific driver
enhancements and fixes. I am sending them in couple of days. With
those patches you will be able to see wireless interface bring up,
connection in open network and data path working.
>
>> > rsi_91x: rsi_sdio_master_reg_read: AHB register read failed
>> > rsi_91x: rsi_load_firmware: REGOUT read failed
>> > rsi_91x: rsi_hal_device_init: Failed to load TA instructions
>> > rsi_91x: rsi_probe: Failed in device init
>> > rsi_91x: rsi_91x_deinit: Performing deinit os ops
>> > rsi_91x: rsi_core_qos_processor: Queue number = 255
>> > rsi_91x: rsi_core_qos_processor: No More Pkt
>> > rsi_91x: rsi_probe: Failed in probe...Exiting
>> > RSI-SDIO WLAN: probe of mmc0:fffd:1 failed with error 1
>> > ----------------------->8--------------------
>> >
>> > 2) In case of USB I just see:
>> > ----------------------->8--------------------
>> > usb 1-1: new high-speed USB device number 6 using ehci-platform
>> > usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 255, changing to 11
>> > usb 1-1: New USB device found, idVendor=1618, idProduct=9113
>> > usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
>> > usb 1-1: Product: Wireless USB-CDC Network Module
>> > usb 1-1: Manufacturer: Redpine Signals, Inc.
>> > cdc_acm 1-1:1.0: ttyACM0: USB ACM device
>> > ----------------------->8--------------------
>> >
>> > I noticed that there're quite some patches floating on linux-wireless mailing list which
>> > were not yet merged in upstream kernel (even in linux-next or wireless-testing).
>> >
>> > So at this point I'm not really sure what could be a safe baseline for my experiments:
>> > - if existing vanilla say 4.11 kernel is good enough and things that doesn't work are caused
>> > by other problems not related to Redpine module (that would be strange because both USB abd SD-card
>> > slot are proven to work pretty well with other devices)
>> > - if I need an arbitrary set of patches to get things up and running etc
>> >
>> > That said if there's a public git repo which contains everything required for Redpine module to
>> > work [preferably based on the latest kernel sources] I'd like to get a reference to it.
>> >
>> > Any hints here are much appreciated.
>>
>> We don't have a public git repo maintained. We have 2 patchsets ready
>> for submission. We are working on code cleanup for other pending
>> changes. I would suggest you to wait till these patches are posted.
>
> Ok, will do. But please add me in Cc list in your upcoming patches as I'm very interested
> in getting Redpine module working on our new board and will be happy to review them as well as test on
> my platform.
>
Sure. I will add you in CC for those patches.
Regards,
Amitkumar Karwar
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: git repo with Redpine changes
2017-06-01 13:54 ` amit karwar
@ 2017-06-01 14:19 ` Alexey Brodkin
-1 siblings, 0 replies; 9+ messages in thread
From: Alexey Brodkin @ 2017-06-01 14:19 UTC (permalink / raw)
To: amitkarwar; +Cc: linux-wireless, prameela.j04cs, amit.karwar, linux-snps-arc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^ permalink raw reply [flat|nested] 9+ messages in thread
* git repo with Redpine changes
@ 2017-06-01 14:19 ` Alexey Brodkin
0 siblings, 0 replies; 9+ messages in thread
From: Alexey Brodkin @ 2017-06-01 14:19 UTC (permalink / raw)
To: linux-snps-arc
Hi Amit!
On Thu, 2017-06-01@19:24 +0530, amit karwar wrote:
> On Tue, May 23, 2017 at 10:56 PM, Alexey Brodkin
> <Alexey.Brodkin@synopsys.com> wrote:
>
> I have posted a firmware image for new firmware loading mechanism to
> community. There are some patches for SDIO specific driver
> enhancements and fixes. I am sending them in couple of days. With
> those patches you will be able to see wireless interface bring up,
> connection in open network and data path working.
May I have any reference to that post/image?
> >
> >
> > >
> > > >
> > > > rsi_91x: rsi_sdio_master_reg_read: AHB register read failed
> > > > rsi_91x: rsi_load_firmware: REGOUT read failed
> > > > rsi_91x: rsi_hal_device_init: Failed to load TA instructions
> > > > rsi_91x: rsi_probe: Failed in device init
> > > > rsi_91x: rsi_91x_deinit: Performing deinit os ops
> > > > rsi_91x: rsi_core_qos_processor: Queue number = 255
> > > > rsi_91x: rsi_core_qos_processor: No More Pkt
> > > > rsi_91x: rsi_probe: Failed in probe...Exiting
> > > > RSI-SDIO WLAN: probe of mmc0:fffd:1 failed with error 1
> > > > ----------------------->8--------------------
> > > >
> > > > ?2) In case of USB I just see:
> > > > ----------------------->8--------------------
> > > > usb 1-1: new high-speed USB device number 6 using ehci-platform
> > > > usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 255, changing to 11
> > > > usb 1-1: New USB device found, idVendor=1618, idProduct=9113
> > > > usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> > > > usb 1-1: Product: Wireless USB-CDC Network Module
> > > > usb 1-1: Manufacturer: Redpine Signals, Inc.
> > > > cdc_acm 1-1:1.0: ttyACM0: USB ACM device
> > > > ----------------------->8--------------------
> > > >
> > > > I noticed that there're quite some patches floating on linux-wireless mailing list which
> > > > were not yet merged in upstream kernel (even in linux-next or wireless-testing).
> > > >
> > > > So at this point I'm not really sure what could be a safe baseline for my experiments:
> > > > ?- if existing vanilla say 4.11 kernel is good enough and things that doesn't work are caused
> > > > ???by other problems not related to Redpine module (that would be strange because both USB abd SD-card
> > > > ???slot are proven to work pretty well with other devices)
> > > > ?- if I need an arbitrary set of patches to get things up and running etc
> > > >
> > > > That said if there's a public git repo which contains everything required for Redpine module to
> > > > work [preferably based on the latest kernel sources] I'd like to get a reference to it.
> > > >
> > > > Any hints here are much appreciated.
> > >
> > > We don't have a public git repo maintained. We have 2 patchsets ready
> > > for submission. We are working on code cleanup for other pending
> > > changes. I would suggest you to wait till these patches are posted.
> >
> > Ok, will do. But please add me in Cc list in your upcoming patches as I'm very interested
> > in getting Redpine module working on our new board and will be happy to review them as well as test on
> > my platform.
> >
>
> Sure. I will add you in CC for those patches.
Thanks a lot!
I\ll keep an eye on those changes once they appear.
-Alexey
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: git repo with Redpine changes
2017-06-01 14:19 ` Alexey Brodkin
@ 2017-06-02 5:30 ` amit karwar
-1 siblings, 0 replies; 9+ messages in thread
From: amit karwar @ 2017-06-02 5:30 UTC (permalink / raw)
To: Alexey Brodkin
Cc: linux-wireless, prameela.j04cs, amit.karwar, linux-snps-arc
On Thu, Jun 1, 2017 at 7:49 PM, Alexey Brodkin
<Alexey.Brodkin@synopsys.com> wrote:
> Hi Amit!
>
> On Thu, 2017-06-01 at 19:24 +0530, amit karwar wrote:
>> On Tue, May 23, 2017 at 10:56 PM, Alexey Brodkin
>> <Alexey.Brodkin@synopsys.com> wrote:
>>
>> I have posted a firmware image for new firmware loading mechanism to
>> community. There are some patches for SDIO specific driver
>> enhancements and fixes. I am sending them in couple of days. With
>> those patches you will be able to see wireless interface bring up,
>> connection in open network and data path working.
>
> May I have any reference to that post/image?
Here is the link:
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=37857004a430e96dc837db7f967b6d0279053de8
Regards,
Amitkumar Karwar
^ permalink raw reply [flat|nested] 9+ messages in thread
* git repo with Redpine changes
@ 2017-06-02 5:30 ` amit karwar
0 siblings, 0 replies; 9+ messages in thread
From: amit karwar @ 2017-06-02 5:30 UTC (permalink / raw)
To: linux-snps-arc
On Thu, Jun 1, 2017 at 7:49 PM, Alexey Brodkin
<Alexey.Brodkin@synopsys.com> wrote:
> Hi Amit!
>
> On Thu, 2017-06-01@19:24 +0530, amit karwar wrote:
>> On Tue, May 23, 2017 at 10:56 PM, Alexey Brodkin
>> <Alexey.Brodkin@synopsys.com> wrote:
>>
>> I have posted a firmware image for new firmware loading mechanism to
>> community. There are some patches for SDIO specific driver
>> enhancements and fixes. I am sending them in couple of days. With
>> those patches you will be able to see wireless interface bring up,
>> connection in open network and data path working.
>
> May I have any reference to that post/image?
Here is the link:
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=37857004a430e96dc837db7f967b6d0279053de8
Regards,
Amitkumar Karwar
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2017-06-02 5:30 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-05-17 8:11 git repo with Redpine changes Alexey Brodkin
[not found] ` <CAEhWJFkVe1C9jtxH9zeeMeJiAs86sJGOKSoqMku0qRqNAQujxg@mail.gmail.com>
2017-05-23 17:26 ` Alexey Brodkin
2017-05-23 17:26 ` Alexey Brodkin
2017-06-01 13:54 ` amit karwar
2017-06-01 13:54 ` amit karwar
2017-06-01 14:19 ` Alexey Brodkin
2017-06-01 14:19 ` Alexey Brodkin
2017-06-02 5:30 ` amit karwar
2017-06-02 5:30 ` amit karwar
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.