* Bug on bootup of Linux kernel on Panasonic Toughbook S10
@ 2012-05-31 21:39 Bill Unruh
2012-06-01 15:47 ` [Bug 43331] " Bjorn Helgaas
0 siblings, 1 reply; 12+ messages in thread
From: Bill Unruh @ 2012-05-31 21:39 UTC (permalink / raw)
To: linux-kernel
I am running Mageia 2 kernel 3.3.6-desktop586-2.mga2
Every time I boot up I get the error messages
pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
I have no idea what this means. The system appears to be running OK (Ie I have
not noticed problems)
I do have to run with noapic or the system randomly crashes (usually during
boot, but sometimes after bootup)
It was suggested that I try the pci=nocrs option which does get rid of that
error message, but also results in a much slower boot and slower running of
the system.
System Panasonic toughbook Cf-S10 (Intel graphics using ram for its memory,
Intel 6205 wireless card).
The dmesg lines from around that error message
[ 2.037963] system 00:0d: [mem 0x20000000-0x201fffff] has been reserved
[ 2.037965] system 00:0d: [mem 0x40000000-0x401fffff] has been reserved
[ 2.037967] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 2.038015] pnp 00:0e: [mem 0xfed98000-0xfed9ffff]
[ 2.038064] system 00:0e: [mem 0xfed98000-0xfed9ffff] has been reserved
[ 2.038067] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.038080] pnp: PnP ACPI: found 15 devices
[ 2.038081] ACPI: ACPI bus type pnp unregistered
[ 2.038083] PnPBIOS: Disabled
[ 2.074428] PCI: max bus depth: 2 pci_try_num: 3
[ 2.074481] pci 0000:00:04.0: BAR 0: assigned [mem 0xdfa00000-0xdfa07fff 64bit]
[ 2.074484] pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
[ 2.074491] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 2.074495] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 2.074500] pci 0000:00:1c.0: bridge window [mem 0xf7b00000-0xf7bfffff]
[ 2.074505] pci 0000:00:1c.0: bridge window [mem 0xf2700000-0xf27fffff
64bit pref] [ 2.074512] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 2.074515] pci 0000:00:1c.1: bridge window [io 0xc000-0xcfff]
[ 2.074521] pci 0000:00:1c.1: bridge window [mem 0xf7a00000-0xf7afffff]
[ 2.074525] pci 0000:00:1c.1: bridge window [mem 0xf2500000-0xf25fffff 64bit pref]
[ 2.074532] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 2.074535] pci 0000:00:1c.2: bridge window [io 0xb000-0xbfff]
[ 2.074541] pci 0000:00:1c.2: bridge window [mem 0xf7900000-0xf79fffff]
[ 2.074545] pci 0000:00:1c.2: bridge window [mem 0xf2300000-0xf23fffff 64bit pref]
[ 2.074557] pci 0000:04:00.0: BAR 16: can't assign mem (size 0x4000000)
[ 2.074564] pci 0000:04:00.0: BAR 15: can't assign mem pref (size 0x4000000)
[ 2.074566] pci 0000:04:00.0: BAR 14: assigned [io 0x8000-0x80ff]
[ 2.074568] pci 0000:04:00.0: BAR 13: assigned [io 0x8400-0x84ff]
Various other information.
:
Linux version 3.3.6-desktop586-2.mga2 (iurt@ecosse.mageia.org) (gcc version 4.6.3 (GCC) ) #1 SMP Thu May 17 16:35:38 UTC 2012
/proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 42
model name : Intel(R) Core(TM) i5-2520M CPU @ 2.50GHz
stepping : 7
microcode : 0x25
cpu MHz : 800.000
cache size : 3072 KB
physical id : 0
siblings : 4
core id : 0
cpu cores : 2
apicid : 0
initial apicid : 0
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow vnmi flexpriority ept vpid
bogomips : 4988.38
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 42
model name : Intel(R) Core(TM) i5-2520M CPU @ 2.50GHz
stepping : 7
microcode : 0x25
cpu MHz : 800.000
cache size : 3072 KB
physical id : 0
siblings : 4
core id : 1
cpu cores : 2
apicid : 2
initial apicid : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow vnmi flexpriority ept vpid
bogomips : 4988.38
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
processor : 2
vendor_id : GenuineIntel
cpu family : 6
model : 42
model name : Intel(R) Core(TM) i5-2520M CPU @ 2.50GHz
stepping : 7
microcode : 0x25
cpu MHz : 800.000
cache size : 3072 KB
physical id : 0
siblings : 4
core id : 0
cpu cores : 2
apicid : 1
initial apicid : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow vnmi flexpriority ept vpid
bogomips : 4988.38
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
processor : 3
vendor_id : GenuineIntel
cpu family : 6
model : 42
model name : Intel(R) Core(TM) i5-2520M CPU @ 2.50GHz
stepping : 7
microcode : 0x25
cpu MHz : 800.000
cache size : 3072 KB
physical id : 0
siblings : 4
core id : 1
cpu cores : 2
apicid : 3
initial apicid : 3
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow vnmi flexpriority ept vpid
bogomips : 4988.38
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
/proc/modules
fuse 72055 3 - Live 0xf5b7d000
ipt_IFWLOG 12550 2 - Live 0xf5b30000
ipt_psd 53435 1 - Live 0xf5e02000
cls_flow 16891 0 - Live 0xf5b35000
cls_fw 12760 0 - Live 0xf5b2b000
cls_u32 16908 0 - Live 0xf5b20000
sch_tbf 12888 0 - Live 0xf5b1b000
sch_prio 12960 0 - Live 0xf5aef000
sch_htb 21741 0 - Live 0xf5aff000
sch_hfsc 25982 0 - Live 0xf5af7000
sch_ingress 12746 0 - Live 0xf5adf000
sch_sfq 17112 0 - Live 0xf5ae9000
bridge 79586 0 - Live 0xf5b06000
stp 12811 1 bridge, Live 0xf5cad000
xt_time 12581 0 - Live 0xf5bd5000
xt_connlimit 12591 0 - Live 0xf5b26000
xt_realm 12450 0 - Live 0xf5bef000
xt_addrtype 12563 4 - Live 0xf5bbd000
ip_set_hash_ip 27265 2 - Live 0xf5b45000
iptable_raw 12598 0 - Live 0xf5b78000
xt_comment 12456 18 - Live 0xf5c6d000
xt_recent 17995 0 - Live 0xf5bcc000
xt_policy 12518 0 - Live 0xf5b40000
ipt_ULOG 13664 0 - Live 0xf5ae4000
ipt_REJECT 12485 4 - Live 0xf5ada000
ipt_REDIRECT 12590 0 - Live 0xf5ad5000
ipt_NETMAP 12582 0 - Live 0xf5ad0000
ipt_MASQUERADE 12760 0 - Live 0xf5acb000
ipt_ECN 12473 0 - Live 0xf5ac1000
ipt_CLUSTERIP 13247 0 - Live 0xf5ac6000
ipt_ah 12694 0 - Live 0xf5ab2000
xt_set 12939 2 - Live 0xf5aad000
ip_set 30822 2 ip_set_hash_ip,xt_set, Live 0xf5ab8000
nf_nat_tftp 12420 0 - Live 0xf5aa2000
nf_nat_snmp_basic 17163 0 - Live 0xf5aa7000
nf_conntrack_snmp 12745 1 nf_nat_snmp_basic, Live 0xf5a9d000
nf_nat_sip 16921 0 - Live 0xf5a97000
nf_nat_pptp 12926 0 - Live 0xf5a92000
nf_nat_proto_gre 12898 1 nf_nat_pptp, Live 0xf5a8d000
nf_nat_irc 12606 0 - Live 0xf5a82000
nf_nat_h323 17359 0 - Live 0xf5a87000
nf_nat_ftp 12645 0 - Live 0xf5a7d000
nf_nat_amanda 12422 0 - Live 0xf5a78000
ts_kmp 12533 5 - Live 0xf5a73000
nf_conntrack_amanda 12897 1 nf_nat_amanda, Live 0xf5a6e000
nf_conntrack_sane 12965 0 - Live 0xf5a5d000
nf_conntrack_tftp 12980 1 nf_nat_tftp, Live 0xf5a28000
nf_conntrack_sip 24594 1 nf_nat_sip, Live 0xf5a66000
nf_conntrack_proto_sctp 18039 0 - Live 0xf5a57000
nf_conntrack_pptp 14615 1 nf_nat_pptp, Live 0xf5a41000
nf_conntrack_proto_gre 13878 1 nf_conntrack_pptp, Live 0xf5a52000
nf_conntrack_netlink 26205 0 - Live 0xf5a4a000
nf_conntrack_netbios_ns 12585 0 - Live 0xf5a23000
nf_conntrack_broadcast 12541 2 nf_conntrack_snmp,nf_conntrack_netbios_ns, Live 0xf5a1e000
nf_conntrack_irc 13275 1 nf_nat_irc, Live 0xf5a08000
nf_conntrack_h323 62776 1 nf_nat_h323, Live 0xf5a30000
nf_conntrack_ftp 14049 1 nf_nat_ftp, Live 0xf5a19000
xt_TPROXY 17135 0 - Live 0xf5a13000
nf_defrag_ipv6 13690 1 xt_TPROXY, Live 0xf5a0e000
nf_tproxy_core 12554 1 xt_TPROXY,[permanent], Live 0xf59fb000
ip6_tables 18115 1 xt_TPROXY, Live 0xf5a02000
xt_tcpmss 12453 0 - Live 0xf51d6000
xt_pkttype 12456 0 - Live 0xf51d1000
xt_physdev 12523 0 - Live 0xf51cc000
xt_owner 12450 0 - Live 0xf51c7000
xt_NFQUEUE 12606 0 - Live 0xf51c2000
xt_NFLOG 12481 0 - Live 0xf51b6000
nfnetlink_log 17489 1 xt_NFLOG, Live 0xf51bc000
xt_multiport 12694 4 - Live 0xf51b1000
xt_mark 12499 1 - Live 0xf51ac000
xt_mac 12444 0 - Live 0xf51a7000
xt_limit 12541 0 - Live 0xf51a2000
xt_length 12480 0 - Live 0xf519d000
xt_iprange 12679 0 - Live 0xf5198000
xt_helper 12519 0 - Live 0xf518d000
xt_hashlimit 17290 0 - Live 0xf5192000
xt_DSCP 12549 0 - Live 0xf5188000
xt_dscp 12525 0 - Live 0xf5183000
xt_dccp 12534 0 - Live 0xf517e000
xt_conntrack 12664 8 - Live 0xf5179000
xt_connmark 12659 0 - Live 0xf5174000
xt_CLASSIFY 12459 0 - Live 0xf5164000
xt_AUDIT 12590 0 - Live 0xf5121000
ipt_LOG 12841 5 - Live 0xf50fb000
xt_tcpudp 12756 11 - Live 0xf506a000
xt_state 12514 1 - Live 0xf501a000
iptable_nat 13138 0 - Live 0xf4bf4000
nf_nat 24963 12 ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,nf_nat_tftp,nf_nat_sip,nf_nat_pptp,nf_nat_proto_gre,nf_nat_irc,nf_nat_h323,nf_nat_ftp,nf_nat_amanda,iptable_nat, Live 0xf516c000
nf_conntrack_ipv4 14277 12 iptable_nat,nf_nat, Live 0xf4bfa000
nf_defrag_ipv4 12649 2 xt_TPROXY,nf_conntrack_ipv4, Live 0xf5015000
nf_conntrack 65397 32 xt_connlimit,ipt_MASQUERADE,ipt_CLUSTERIP,nf_nat_tftp,nf_nat_snmp_basic,nf_conntrack_snmp,nf_nat_sip,nf_nat_pptp,nf_nat_irc,nf_nat_h323,nf_nat_ftp,nf_nat_amanda,nf_conntrack_amanda,nf_conntrack_sane,nf_conntrack_tftp,nf_conntrack_sip,nf_conntrack_proto_sctp,nf_conntrack_pptp,nf_conntrack_proto_gre,nf_conntrack_netlink,nf_conntrack_netbios_ns,nf_conntrack_broadcast,nf_conntrack_irc,nf_conntrack_h323,nf_conntrack_ftp,xt_helper,xt_conntrack,xt_connmark,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4, Live 0xf50ea000
iptable_mangle 12615 1 - Live 0xf4bef000
nfnetlink 13983 3 ip_set,nf_conntrack_netlink,nfnetlink_log, Live 0xf4777000
iptable_filter 12706 1 - Live 0xf476a000
ip_tables 17987 4 iptable_raw,iptable_nat,iptable_mangle,iptable_filter, Live 0xf4bdf000
x_tables 21992 49 ipt_IFWLOG,ipt_psd,xt_time,xt_connlimit,xt_realm,xt_addrtype,iptable_raw,xt_comment,xt_recent,xt_policy,ipt_ULOG,ipt_REJECT,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,ipt_ECN,ipt_CLUSTERIP,ipt_ah,xt_set,xt_TPROXY,ip6_tables,xt_tcpmss,xt_pkttype,xt_physdev,xt_owner,xt_NFQUEUE,xt_NFLOG,xt_multiport,xt_mark,xt_mac,xt_limit,xt_length,xt_iprange,xt_helper,xt_hashlimit,xt_DSCP,xt_dscp,xt_dccp,xt_conntrack,xt_connmark,xt_CLASSIFY,xt_AUDIT,ipt_LOG,xt_tcpudp,xt_state,iptable_nat,iptable_mangle,iptable_filter,ip_tables, Live 0xf4be8000
rfcomm 57543 8 - Live 0xf50da000
bnep 18867 2 - Live 0xf45c6000
snd_hda_codec_hdmi 31470 1 - Live 0xf4bd6000
cpufreq_ondemand 13452 4 - Live 0xf476f000
cpufreq_conservative 13495 0 - Live 0xf4737000
cpufreq_powersave 12554 0 - Live 0xf46a1000
acpi_cpufreq 14206 1 - Live 0xf4732000
mperf 12603 1 acpi_cpufreq, Live 0xf472d000
snd_hda_codec_realtek 121605 1 - Live 0xf504b000
freq_table 14322 2 cpufreq_ondemand,acpi_cpufreq, Live 0xf45ea000
nvram 13957 0 - Live 0xf4673000
snd_hda_intel 32340 3 - Live 0xf4761000
snd_hda_codec 108688 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel, Live 0xf4623000
arc4 12473 2 - Live 0xf42a1000
snd_pcm 88532 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec, Live 0xf4711000
snd_page_alloc 14036 2 snd_hda_intel,snd_pcm, Live 0xf45b2000
snd_hwdep 13276 1 snd_hda_codec, Live 0xf45c1000
snd_timer 28598 1 snd_pcm, Live 0xf45e2000
snd 65929 13 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_pcm,snd_hwdep,snd_timer, Live 0xf4661000
tpm_tis 18576 0 - Live 0xf433f000
btusb 23231 1 - Live 0xf45ba000
iwlwifi 286332 0 - Live 0xf523c000
mac80211 384735 1 iwlwifi, Live 0xf51dd000
iTCO_wdt 17652 0 - Live 0xf434d000
iTCO_vendor_support 13502 1 iTCO_wdt, Live 0xf426c000
e1000e 175646 0 - Live 0xf4fe9000
mei 68995 0 - Live 0xf45d0000 (C)
bluetooth 239698 23 rfcomm,bnep,btusb, Live 0xf5128000
soundcore 14599 1 snd, Live 0xf4267000
tpm_infineon 13200 0 - Live 0xf4273000
cfg80211 169030 2 iwlwifi,mac80211, Live 0xf5020000
panasonic_laptop 13194 0 - Live 0xf427b000
serio_raw 13155 0 - Live 0xf4246000
i2c_i801 17506 0 - Live 0xf4250000
sparse_keymap 13658 1 panasonic_laptop, Live 0xf4728000
tpm 21864 2 tpm_tis,tpm_infineon, Live 0xf42b6000
battery 13522 0 - Live 0xf424b000
processor 30402 1 acpi_cpufreq, Live 0xf42ad000
thermal 13830 0 - Live 0xf4227000
tpm_bios 13421 1 tpm, Live 0xf4210000
rfkill 20902 3 bluetooth,cfg80211, Live 0xf4331000
joydev 17161 0 - Live 0xf42a7000
evdev 17445 7 - Live 0xf4221000
ac 12742 0 - Live 0xf41bc000
ipv6 286407 55 bridge,xt_TPROXY,nf_defrag_ipv6, Live 0xf42cb000
autofs4 37365 3 - Live 0xf4296000
ext4 428767 2 - Live 0xf5070000
jbd2 75163 1 ext4, Live 0xf4282000
crc16 12595 2 bluetooth,ext4, Live 0xf41c7000
mmc_block 26567 0 - Live 0xf4185000
pcmcia 51330 0 - Live 0xf4259000
rts_pstor 341858 0 - Live 0xf4b81000 (C)
xhci_hcd 115575 0 - Live 0xf4313000
sd_mod 43934 4 - Live 0xf42bf000
sdhci_pci 18149 0 - Live 0xf420a000
sr_mod 21872 0 - Live 0xf41a8000
sdhci 37180 1 sdhci_pci, Live 0xf4216000
crc_t10dif 12507 1 sd_mod, Live 0xf4195000
mmc_core 100789 3 mmc_block,sdhci_pci,sdhci, Live 0xf422c000
ehci_hcd 55582 0 - Live 0xf41cd000
yenta_socket 36268 0 - Live 0xf41af000
usbcore 177104 4 btusb,xhci_hcd,ehci_hcd, Live 0xf41dd000
pcmcia_rsrc 18319 1 yenta_socket, Live 0xf419a000
pcmcia_core 22246 3 pcmcia,yenta_socket,pcmcia_rsrc, Live 0xf418e000
usb_common 12525 1 usbcore, Live 0xf4180000
i915 414077 3 - Live 0xf46aa000
video 18640 1 i915, Live 0xf45ac000
button 13561 1 i915, Live 0xf416d000
i2c_algo_bit 13080 1 i915, Live 0xf435c000
drm_kms_helper 32743 1 i915, Live 0xf4177000
drm 208242 4 i915,drm_kms_helper, Live 0xf45ef000
i2c_core 29836 5 i2c_i801,i915,i2c_algo_bit,drm_kms_helper,drm, Live 0xf4377000
dm_mirror 21654 0 - Live 0xf4364000
dm_region_hash 15977 1 dm_mirror, Live 0xf4172000
dm_log 18111 2 dm_mirror,dm_region_hash, Live 0xf4356000
dm_mod 75920 2 dm_mirror,dm_log, Live 0xf406b000
ata_piix 22146 0 - Live 0xf4132000
ahci 25496 4 - Live 0xf4059000
libahci 25805 1 ahci, Live 0xf4063000
libata 183151 3 ata_piix,ahci,libahci, Live 0xf402b000
mpt2sas 168588 0 - Live 0xf4581000
raid_class 13293 1 mpt2sas, Live 0xf4019000
scsi_transport_sas 34482 1 mpt2sas, Live 0xf4021000
scsi_mod 186048 7 rts_pstor,sd_mod,sr_mod,libata,mpt2sas,raid_class,scsi_transport_sas, Live 0xf413e000
/proc/ioports
0000-0cf7 : PCI Bus 0000:00
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0062-0062 : EC data
0064-0064 : keyboard
0066-0066 : EC cmd
0070-0077 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
03c0-03df : vesafb
0400-0453 : pnp 00:05
0400-0403 : ACPI PM1a_EVT_BLK
0404-0405 : ACPI PM1a_CNT_BLK
0408-040b : ACPI PM_TMR
0410-0415 : ACPI CPU throttle
0420-042f : ACPI GPE0_BLK
0450-0450 : ACPI PM2_CNT_BLK
0454-0457 : pnp 00:07
0458-047f : pnp 00:05
0500-057f : pnp 00:05
0900-097f : pnp 00:05
0cf8-0cff : PCI conf1
0d00-ffff : PCI Bus 0000:00
1000-100f : pnp 00:05
8000-9fff : PCI Bus 0000:04
8000-80ff : PCI CardBus 0000:40
8400-84ff : PCI CardBus 0000:40
a000-afff : PCI Bus 0000:0d
b000-bfff : PCI Bus 0000:03
c000-cfff : PCI Bus 0000:02
d000-dfff : PCI Bus 0000:01
e000-e03f : 0000:00:02.0
e040-e05f : 0000:00:1f.3
e060-e07f : 0000:00:1f.2
e060-e07f : ahci
e080-e09f : 0000:00:19.0
e0a0-e0a3 : 0000:00:1f.2
e0a0-e0a3 : ahci
e0b0-e0b7 : 0000:00:1f.2
e0b0-e0b7 : ahci
e0c0-e0c3 : 0000:00:1f.2
e0c0-e0c3 : ahci
e0d0-e0d7 : 0000:00:1f.2
e0d0-e0d7 : ahci
e0e0-e0e7 : 0000:00:16.3
e0e0-e0e7 : serial
ffff-ffff : pnp 00:05
ffff-ffff : pnp 00:05
/proc/iomem
00000000-0000ffff : reserved
00010000-0009e7ff : System RAM
0009e800-0009ffff : reserved
000a0000-000bffff : PCI Bus 0000:00
000a0000-000bffff : Video RAM area
000c0000-000cf1ff : Video ROM
000cf200-000cf7ff : pnp 00:01
000cf800-000d07ff : Adapter ROM
000d0800-000d3fff : pnp 00:01
000d4000-000d7fff : PCI Bus 0000:00
000d8000-000dbfff : PCI Bus 0000:00
000dc000-000dffff : PCI Bus 0000:00
000e0000-000fffff : reserved
000f0000-000fffff : System ROM
00100000-1fffffff : System RAM
00100000-004bbff3 : Kernel code
004bbff4-006b7dbf : Kernel data
00749000-007d4fff : Kernel bss
20000000-201fffff : reserved
20000000-201fffff : pnp 00:0d
20200000-3fffffff : System RAM
40000000-401fffff : reserved
40000000-401fffff : pnp 00:0d
40200000-dac33fff : System RAM
dac34000-dad8dfff : reserved
dad8e000-dad9dfff : System RAM
dad9e000-dad9ffff : reserved
dada0000-dada0fff : System RAM
dada1000-dade7fff : reserved
dade8000-daf39fff : System RAM
daf3a000-daf80fff : ACPI Non-volatile Storage
daf81000-daf87fff : reserved
daf88000-dafe7fff : ACPI Non-volatile Storage
dafe8000-dafebfff : System RAM
dafec000-df9fffff : reserved
dfa00000-feafffff : PCI Bus 0000:00
dfa00000-dfa07fff : 0000:00:04.0
e0000000-efffffff : 0000:00:02.0
f0000000-f1ffffff : PCI Bus 0000:04
f2100000-f21fffff : PCI Bus 0000:0d
f2300000-f23fffff : PCI Bus 0000:03
f2500000-f25fffff : PCI Bus 0000:02
f2700000-f27fffff : PCI Bus 0000:01
f5400000-f57fffff : 0000:00:02.0
f5800000-f77fffff : PCI Bus 0000:04
f5800000-f6bfffff : PCI CardBus 0000:40
f6c00000-f6c00fff : 0000:04:00.0
f6c00000-f6c00fff : yenta_socket
f7000000-f73fffff : PCI CardBus 0000:40
f7800000-f78fffff : PCI Bus 0000:0d
f7800000-f78000ff : 0000:0d:00.1
f7800000-f78000ff : mmc0
f7801000-f7801fff : 0000:0d:00.0
f7801000-f7801fff : rts_pstor
f7900000-f79fffff : PCI Bus 0000:03
f7900000-f7901fff : 0000:03:00.0
f7900000-f7901fff : iwlwifi
f7a00000-f7afffff : PCI Bus 0000:02
f7a00000-f7a01fff : 0000:02:00.0
f7a00000-f7a01fff : xhci_hcd
f7b00000-f7bfffff : PCI Bus 0000:01
f7c00000-f7c1ffff : 0000:00:19.0
f7c00000-f7c1ffff : e1000e
f7c28000-f7c2bfff : 0000:00:1b.0
f7c28000-f7c2bfff : ICH HD audio
f7c2c000-f7c2cfff : 0000:00:1f.6
f7c2d000-f7c2d0ff : 0000:00:1f.3
f7c2e000-f7c2e7ff : 0000:00:1f.2
f7c2e000-f7c2e7ff : ahci
f7c2f000-f7c2f3ff : 0000:00:1d.0
f7c2f000-f7c2f3ff : ehci_hcd
f7c30000-f7c303ff : 0000:00:1a.0
f7c30000-f7c303ff : ehci_hcd
f7c31000-f7c31fff : 0000:00:19.0
f7c31000-f7c31fff : e1000e
f7c32000-f7c32fff : 0000:00:16.3
f7c34000-f7c3400f : 0000:00:16.0
f7c34000-f7c3400f : mei
f8000000-fbffffff : PCI MMCONFIG 0000 [bus 00-3f]
f8000000-fbffffff : reserved
f8000000-fbffffff : pnp 00:0b
fec00000-fec00fff : reserved
fed00000-fed003ff : HPET 0
fed08000-fed08fff : pnp 00:0b
fed10000-fed13fff : reserved
fed18000-fed19fff : reserved
fed18000-fed18fff : pnp 00:0b
fed19000-fed19fff : pnp 00:0b
fed1c000-fed1ffff : reserved
fed1c000-fed1ffff : pnp 00:0b
fed20000-fed3ffff : pnp 00:0b
fed40000-fed44fff : PCI Bus 0000:00
fed45000-fed8ffff : pnp 00:0b
fed90000-fed93fff : pnp 00:0b
fed98000-fed9ffff : pnp 00:0e
fee00000-fee00fff : Local APIC
fee00000-fee00fff : reserved
ff980000-ffbfffff : reserved
ffd80000-ffffffff : reserved
--------
lspci -vvv
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f5400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at e000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 4061
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: i915
00:04.0 Signal processing controller: Intel Corporation Device 0103 (rev 09)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at dfa00000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 51
Region 0: Memory at f7c34000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00000 Data: 4091
Kernel driver in use: mei
00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) (prog-if 02 [16550])
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at e0e0 [size=8]
Region 1: Memory at f7c32000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: serial
00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 52
Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7c31000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at e080 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00000 Data: 40b9
Capabilities: [e0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: e1000e
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI])
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7c30000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 54
Region 0: Memory at f7c28000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00000 Data: 40a9
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7b00000-f7bfffff
Prefetchable memory behind bridge: 00000000f2700000-00000000f27fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 4029
Capabilities: [90] Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f7a00000-f7afffff
Prefetchable memory behind bridge: 00000000f2500000-00000000f25fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 4041
Capabilities: [90] Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f7900000-f79fffff
Prefetchable memory behind bridge: 00000000f2300000-00000000f23fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 4049
Capabilities: [90] Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev b4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=0c, sec-latency=0
I/O behind bridge: 00008000-00009fff
Memory behind bridge: f5800000-f77fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f7800000-f78fffff
Prefetchable memory behind bridge: 00000000f2100000-00000000f21fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 4051
Capabilities: [90] Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI])
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f7c2f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at e0d0 [size=8]
Region 1: I/O ports at e0c0 [size=4]
Region 2: I/O ports at e0b0 [size=8]
Region 3: I/O ports at e0a0 [size=4]
Region 4: I/O ports at e060 [size=32]
Region 5: Memory at f7c2e000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 4059
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f7c2d000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at e040 [size=32]
00:1f.6 Signal processing controller: Intel Corporation 6 Series/C200 Series Chipset Family Thermal Management Controller (rev 04)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f7c2c000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
02:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI])
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4
Region 0: Memory at f7a00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: xhci_hcd
03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 (rev 34)
Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at f7900000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00000 Data: 40a1
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 08-11-96-ff-ff-3d-5b-30
Kernel driver in use: iwlwifi
04:00.0 CardBus bridge: Ricoh Co Ltd Device e476 (rev 02)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f6c00000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=40, subordinate=43, sec-latency=176
Memory window 0: f5800000-f6bfffff (prefetchable)
Memory window 1: f7000000-f73fffff
I/O window 0: 00008400-000084ff
I/O window 1: 00008000-000080ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
0d:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader (rev 01)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7801000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Device Serial Number 00-00-00-01-00-4c-e0-00
Kernel driver in use: rts_pstor
0d:00.1 SD Host controller: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader (rev 01)
Subsystem: Matsushita Electric Industrial Co., Ltd. Device 8338
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f7800000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [b0] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Device Serial Number 00-00-00-01-00-4c-e0-00
Kernel driver in use: sdhci-pci
^ permalink raw reply [flat|nested] 12+ messages in thread
* [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-05-31 21:39 Bug on bootup of Linux kernel on Panasonic Toughbook S10 Bill Unruh
@ 2012-06-01 15:47 ` Bjorn Helgaas
2012-06-01 16:22 ` Bill Unruh
2012-06-01 17:04 ` Bill Unruh
0 siblings, 2 replies; 12+ messages in thread
From: Bjorn Helgaas @ 2012-06-01 15:47 UTC (permalink / raw)
To: Bill Unruh; +Cc: linux-kernel, linux-pci, bugzilla-daemon
On Thu, May 31, 2012 at 3:39 PM, Bill Unruh <unruh@physics.ubc.ca> wrote:
> I am running Mageia 2 kernel 3.3.6-desktop586-2.mga2
>
> Every time I boot up I get the error messages
> pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
Thanks very much for this report. I opened this bug report to help me
keep track of it: https://bugzilla.kernel.org/show_bug.cgi?id=43331
The message means that we tried to write address 0xdfa00000 to BAR 0
of device 00:04.0 (a "signal processing controller," whatever that
is), but when we read the BAR back, we read 0xfed98004 instead.
That's an interesting address because it looks a lot like a resource
of an ACPI PNP0c02 device:
system 00:0e: [mem 0xfed98000-0xfed9ffff] has been reserved
system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
You say your machine runs OK (with "noapic"), but I'm doubtful that
00:04.0 is working -- it doesn't even seem to have a driver bound to
it. I don't know what the device does, but if you're not using it,
it's not surprising that you wouldn't notice it being broken.
Can you attach the complete dmesg log to the bugzilla? It will have
more details about other devices and the ranges from which we allocate
resources for PCI devices.
You mention that the machine is not reliable unless you use "noapic".
That sounds like a separate bug, but also something it would be good
to track down.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-06-01 15:47 ` [Bug 43331] " Bjorn Helgaas
@ 2012-06-01 16:22 ` Bill Unruh
2012-06-02 3:30 ` Jiang Liu
2012-06-01 17:04 ` Bill Unruh
1 sibling, 1 reply; 12+ messages in thread
From: Bill Unruh @ 2012-06-01 16:22 UTC (permalink / raw)
To: Bjorn Helgaas; +Cc: linux-kernel, linux-pci, bugzilla-daemon
[-- Attachment #1: Type: TEXT/PLAIN, Size: 2241 bytes --]
Attached is a complete dmesg from a bootup of the kernel on the toughbook S10.
RE the noapic, I have no idea how I can give more information on it, since the
crash almost always occurs during the boot process itself, often very early in
the process. I will see if I can resurect the dmesg that gets saved, if any,
during that process. It is probably also an earlier kernel. I have not dared
try my current kernel with noapic, but perhaps I will try.
On Fri, 1 Jun 2012, Bjorn Helgaas wrote:
> On Thu, May 31, 2012 at 3:39 PM, Bill Unruh <unruh@physics.ubc.ca> wrote:
>> I am running Mageia 2 kernel 3.3.6-desktop586-2.mga2
>>
>> Every time I boot up I get the error messages
>> pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
>
> Thanks very much for this report. I opened this bug report to help me
> keep track of it: https://bugzilla.kernel.org/show_bug.cgi?id=43331
>
> The message means that we tried to write address 0xdfa00000 to BAR 0
> of device 00:04.0 (a "signal processing controller," whatever that
> is), but when we read the BAR back, we read 0xfed98004 instead.
> That's an interesting address because it looks a lot like a resource
> of an ACPI PNP0c02 device:
>
> system 00:0e: [mem 0xfed98000-0xfed9ffff] has been reserved
> system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
>
> You say your machine runs OK (with "noapic"), but I'm doubtful that
> 00:04.0 is working -- it doesn't even seem to have a driver bound to
> it. I don't know what the device does, but if you're not using it,
> it's not surprising that you wouldn't notice it being broken.
>
> Can you attach the complete dmesg log to the bugzilla? It will have
> more details about other devices and the ranges from which we allocate
> resources for PCI devices.
>
> You mention that the machine is not reliable unless you use "noapic".
> That sounds like a separate bug, but also something it would be good
> to track down.
>
--
William G. Unruh | Canadian Institute for| Tel: +1(604)822-3273
Physics&Astronomy | Advanced Research | Fax: +1(604)822-5324
UBC, Vancouver,BC | Program in Cosmology | unruh@physics.ubc.ca
Canada V6T 1Z1 | and Gravity | www.theory.physics.ubc.ca/
[-- Attachment #2: Type: TEXT/PLAIN, Size: 70339 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.3.6-desktop586-2.mga2 (iurt@ecosse.mageia.org) (gcc version 4.6.3 (GCC) ) #1 SMP Thu May 17 16:35:38 UTC 2012
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
[ 0.000000] BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
[ 0.000000] BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
[ 0.000000] BIOS-e820: 0000000040200000 - 00000000dac34000 (usable)
[ 0.000000] BIOS-e820: 00000000dac34000 - 00000000dad8e000 (reserved)
[ 0.000000] BIOS-e820: 00000000dad8e000 - 00000000dad9e000 (usable)
[ 0.000000] BIOS-e820: 00000000dad9e000 - 00000000dada0000 (reserved)
[ 0.000000] BIOS-e820: 00000000dada0000 - 00000000dada1000 (usable)
[ 0.000000] BIOS-e820: 00000000dada1000 - 00000000dade8000 (reserved)
[ 0.000000] BIOS-e820: 00000000dade8000 - 00000000daf3a000 (usable)
[ 0.000000] BIOS-e820: 00000000daf3a000 - 00000000daf81000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000daf81000 - 00000000daf88000 (reserved)
[ 0.000000] BIOS-e820: 00000000daf88000 - 00000000dafe8000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dafe8000 - 00000000dafec000 (usable)
[ 0.000000] BIOS-e820: 00000000dafec000 - 00000000dfa00000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff980000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000011e600000 (usable)
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: Panasonic Corporation CF-S10CDHEDM/CFS10-2, BIOS V2.00L12 06/16/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0xdafec max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-D3FFF write-protect
[ 0.000000] D4000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 100000000 mask FE0000000 write-back
[ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 3 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 4 base 0DB000000 mask FFF000000 uncachable
[ 0.000000] 5 base 11F000000 mask FFF000000 uncachable
[ 0.000000] 6 base 11E800000 mask FFF800000 uncachable
[ 0.000000] 7 base 11E600000 mask FFFE00000 uncachable
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000db000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] found SMP MP-table at [c00fd720] fd720
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] Base memory trampoline at [c009a000] 9a000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000337fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0033400000 page 2M
[ 0.000000] 0033400000 - 00337fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 337fe000 @ bfb000-c00000
[ 0.000000] RAMDISK: 1f050000 - 1fff0000
[ 0.000000] ACPI: RSDP 000f0430 00024 (v02 MATBIO)
[ 0.000000] ACPI: XSDT daffee18 0008C (v01 MATBIO CFS10-2 06222004 MSFT 00010013)
[ 0.000000] ACPI: FACP daffdc18 000F4 (v04 MATBIO CFS10-2 06222004 MSFT 00010013)
[ 0.000000] ACPI Warning: 32/64 FACS address mismatch in FADT - two FACS tables! (20120111/tbfadt-378)
[ 0.000000] ACPI Warning: 32/64X FACS address mismatch in FADT - 0xDAFD4E40/0x00000000DAFD4D40, using 32 (20120111/tbfadt-502)
[ 0.000000] ACPI: DSDT daff1018 0B1B1 (v01 MATBIO CFS10-2 00000000 INTL 20091112)
[ 0.000000] ACPI: FACS dafd4e40 00040
[ 0.000000] ACPI: APIC daffdf18 000CC (v02 MATBIO CFS10-2 06222004 MSFT 00010013)
[ 0.000000] ACPI: HPET daffff18 00038 (v01 MATBIO CFS10-2 06222004 AMI. 00000003)
[ 0.000000] ACPI: SLIC daff0e18 00176 (v01 MATBIO CFS10-2 06222004 AMI 00010013)
[ 0.000000] ACPI: MCFG dafffe98 0003C (v01 MATBIO CFS10-2 06222004 MSFT 00000097)
[ 0.000000] ACPI: SSDT dafef818 007C2 (v01 PmRef Cpu0Ist 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT dafee018 009A0 (v01 PmRef CpuPm 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT dafeda98 002EC (v01 PmRef Cpu0Tst 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT dafecc18 003C6 (v01 PmRef ApTst 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT daf81018 06D34 (v01 DppmRe OemDppm 00001000 INTL 20091112)
[ 0.000000] ACPI: TCPA dafffe18 00032 (v02 MATBIO CFS10-2 00000001 MSFT 01000013)
[ 0.000000] ACPI: ASF! daffea18 00074 (v32 MATBIO CFS10-2 06222004 INTL 000F4240)
[ 0.000000] ACPI: SSDT dafed718 002DB (v01 SataRe SataTabl 00001000 INTL 20091112)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 2679MB HIGHMEM available.
[ 0.000000] 823MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 337fe000
[ 0.000000] low ram: 0 - 337fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000337fe
[ 0.000000] HighMem 0x000337fe -> 0x000dafec
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x00020000
[ 0.000000] 0: 0x00020200 -> 0x00040000
[ 0.000000] 0: 0x00040200 -> 0x000dac34
[ 0.000000] 0: 0x000dad8e -> 0x000dad9e
[ 0.000000] 0: 0x000dada0 -> 0x000dada1
[ 0.000000] 0: 0x000dade8 -> 0x000daf3a
[ 0.000000] 0: 0x000dafe8 -> 0x000dafec
[ 0.000000] On node 0 totalpages: 895273
[ 0.000000] free_area_init_node: node 0, pgdat c06aab00, node_mem_map f1c9d200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3950 pages, LIFO batch:0
[ 0.000000] Normal zone: 1616 pages used for memmap
[ 0.000000] Normal zone: 204718 pages, LIFO batch:31
[ 0.000000] HighMem zone: 5360 pages used for memmap
[ 0.000000] HighMem zone: 679597 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x08] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x09] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0a] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0b] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0c] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0d] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0e] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x0f] disabled)
[ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option.
[ 0.000000] Using ACPI for processor (LAPIC) configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] MPTABLE: OEM ID: CFS10-2
[ 0.000000] MPTABLE: Product ID: MATBIO
[ 0.000000] MPTABLE: APIC at: 0xFEE00000
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] Processors: 4
[ 0.000000] SMP: Allowing 16 CPUs, 12 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[ 0.000000] Allocating PCI resources starting at dfa00000 (gap: dfa00000:18600000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:16 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f1bbb000 s30144 r0 d23104 u53248
[ 0.000000] pcpu-alloc: s30144 r0 d23104 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07
[ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 888265
[ 0.000000] Kernel command line: BOOT_IMAGE=mageialinux root=UUID=439c3c53-7383-4574-8d0c-f109cb963969 splash quiet noapic resume=UUID=d8293c01-7d70-4e9b-b1f4-a661d7dc0fe4 vga=788
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Initializing HighMem for node 0 (000337fe:000dafec)
[ 0.000000] Memory: 3528332k/3588016k available (3823k kernel code, 52760k reserved, 2031k data, 556k init, 2739828k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd34000 - 0xfffff000 (2860 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf3ffe000 - 0xff7fe000 ( 184 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf37fe000 ( 823 MB)
[ 0.000000] .init : 0xc06b8000 - 0xc0743000 ( 556 kB)
[ 0.000000] .data : 0xc04bbff4 - 0xc06b7dc0 (2031 kB)
[ 0.000000] .text : 0xc0100000 - 0xc04bbff4 (3823 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:2304 nr_irqs:808 16
[ 0.000000] CPU 0 irqstacks, hard=f140e000 soft=f1410000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.001000] Detected 2494.143 MHz processor.
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4988.28 BogoMIPS (lpj=2494143)
[ 0.000006] pid_max: default: 32768 minimum: 301
[ 0.000032] Security Framework initialized
[ 0.000040] TOMOYO Linux initialized
[ 0.000055] Mount-cache hash table entries: 512
[ 0.000173] Initializing cgroup subsys cpuacct
[ 0.000175] Initializing cgroup subsys devices
[ 0.000177] Initializing cgroup subsys freezer
[ 0.000178] Initializing cgroup subsys net_cls
[ 0.000180] Initializing cgroup subsys blkio
[ 0.000205] CPU: Physical Processor ID: 0
[ 0.000206] CPU: Processor Core ID: 0
[ 0.000210] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.000211] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.000213] mce: CPU supports 7 MCE banks
[ 0.000224] CPU0: Thermal monitoring enabled (TM1)
[ 0.000231] using mwait in idle threads.
[ 0.001234] ACPI: Checking initramfs for custom DSDT
[ 1.261061] ACPI: Core revision 20120111
[ 1.269734] ACPI: setting ELCR to 0200 (from 0c38)
[ 1.285082] ftrace: allocating 16611 entries in 33 pages
[ 1.294194] Overriding APIC driver with bigsmp
[ 1.294197] Enabling APIC mode: Physflat. Using 1 I/O APICs
[ 1.294202] Leaving ESR disabled.
[ 1.294203] CPU0: Intel(R) Core(TM) i5-2520M CPU @ 2.50GHz stepping 07
[ 1.395128] Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
[ 1.395133] PEBS disabled due to CPU errata.
[ 1.395136] ... version: 3
[ 1.395137] ... bit width: 48
[ 1.395138] ... generic registers: 4
[ 1.395139] ... value mask: 0000ffffffffffff
[ 1.395141] ... max period: 000000007fffffff
[ 1.395142] ... fixed-purpose events: 3
[ 1.395143] ... event mask: 000000070000000f
[ 1.395287] CPU 1 irqstacks, hard=f14e0000 soft=f14e2000
[ 1.395288] Booting Node 0, Processors #1
[ 1.395290] smpboot cpu 1: start_ip = 9a000
[ 1.405499] Initializing CPU#1
[ 1.406284] Leaving ESR disabled.
[ 1.426433] CPU 2 irqstacks, hard=f14ec000 soft=f14ee000
[ 1.426435] #2
[ 1.426436] smpboot cpu 2: start_ip = 9a000
[ 1.436793] Initializing CPU#2
[ 1.437528] Leaving ESR disabled.
[ 1.457677] CPU 3 irqstacks, hard=f14f8000 soft=f14fa000
[ 1.457679] #3
[ 1.457680] smpboot cpu 3: start_ip = 9a000
[ 1.467988] Initializing CPU#3
[ 1.468773] Leaving ESR disabled.
[ 1.488862] Brought up 4 CPUs
[ 1.488864] Total of 4 processors activated (19953.14 BogoMIPS).
[ 1.492184] devtmpfs: initialized
[ 1.492314] PM: Registering ACPI NVS region at daf3a000 (290816 bytes)
[ 1.492322] PM: Registering ACPI NVS region at daf88000 (393216 bytes)
[ 1.493083] RTC time: 13:47:16, date: 05/22/12
[ 1.493119] NET: Registered protocol family 16
[ 1.493235] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 1.493237] ACPI: bus type pci registered
[ 1.493345] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 1.493348] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 1.493350] PCI: Using MMCONFIG for extended config space
[ 1.493351] PCI: Using configuration type 1 for base access
[ 1.493821] bio: create slab <bio-0> at 0
[ 1.493881] ACPI: Added _OSI(Module Device)
[ 1.493883] ACPI: Added _OSI(Processor Device)
[ 1.493885] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 1.493887] ACPI: Added _OSI(Processor Aggregator Device)
[ 1.495858] ACPI: EC: Look up EC in DSDT
[ 1.498126] ACPI: Executed 5 blocks of module-level executable AML code
[ 1.507142] ACPI: SSDT dafd5d18 00056 (v01 DynTbl VistaTbl 00000001 INTL 20091112)
[ 1.507644] ACPI: Dynamic OEM Table Load:
[ 1.507646] ACPI: SSDT (null) 00056 (v01 DynTbl VistaTbl 00000001 INTL 20091112)
[ 1.513008] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 1.520767] ACPI: SSDT dadcb018 00869 (v01 PmRef Cpu0Cst 00003001 INTL 20091112)
[ 1.521302] ACPI: Dynamic OEM Table Load:
[ 1.521305] ACPI: SSDT (null) 00869 (v01 PmRef Cpu0Cst 00003001 INTL 20091112)
[ 1.524232] ACPI: SSDT dadcca98 00303 (v01 PmRef ApIst 00003000 INTL 20091112)
[ 1.524799] ACPI: Dynamic OEM Table Load:
[ 1.524801] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20091112)
[ 1.527078] ACPI: SSDT dadcad98 00119 (v01 PmRef ApCst 00003000 INTL 20091112)
[ 1.527601] ACPI: Dynamic OEM Table Load:
[ 1.527603] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20091112)
[ 1.938712] ACPI: Interpreter enabled
[ 1.938723] ACPI: (supports S0 S3 S4 S5)
[ 1.938744] ACPI: Using PIC for interrupt routing
[ 1.956060] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 1.956425] ACPI: ACPI Dock Station Driver: 1 docks/bays found
[ 1.956431] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.956921] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 1.957225] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 1.957227] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 1.957229] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 1.957232] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 1.957234] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 1.957235] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[ 1.957237] pci_root PNP0A08:00: host bridge window [mem 0xdfa00000-0xfeafffff]
[ 1.957239] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[ 1.957268] PCI host bridge to bus 0000:00
[ 1.957270] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 1.957271] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 1.957273] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 1.957275] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 1.957277] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 1.957278] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 1.957280] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
[ 1.957282] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 1.957290] pci 0000:00:00.0: [8086:0104] type 0 class 0x000600
[ 1.957330] pci 0000:00:02.0: [8086:0126] type 0 class 0x000300
[ 1.957341] pci 0000:00:02.0: reg 10: [mem 0xf5400000-0xf57fffff 64bit]
[ 1.957347] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 1.957352] pci 0000:00:02.0: reg 20: [io 0xe000-0xe03f]
[ 1.957383] pci 0000:00:04.0: [8086:0103] type 0 class 0x001180
[ 1.957394] pci 0000:00:04.0: reg 10: [mem 0xfed98000-0xfed9ffff 64bit]
[ 1.957456] pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
[ 1.957479] pci 0000:00:16.0: reg 10: [mem 0xf7c34000-0xf7c3400f 64bit]
[ 1.957556] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 1.957583] pci 0000:00:16.3: [8086:1c3d] type 0 class 0x000700
[ 1.957603] pci 0000:00:16.3: reg 10: [io 0xe0e0-0xe0e7]
[ 1.957613] pci 0000:00:16.3: reg 14: [mem 0xf7c32000-0xf7c32fff]
[ 1.957714] pci 0000:00:19.0: [8086:1502] type 0 class 0x000200
[ 1.957733] pci 0000:00:19.0: reg 10: [mem 0xf7c00000-0xf7c1ffff]
[ 1.957742] pci 0000:00:19.0: reg 14: [mem 0xf7c31000-0xf7c31fff]
[ 1.957751] pci 0000:00:19.0: reg 18: [io 0xe080-0xe09f]
[ 1.957818] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 1.957845] pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
[ 1.957866] pci 0000:00:1a.0: reg 10: [mem 0xf7c30000-0xf7c303ff]
[ 1.957962] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 1.957991] pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
[ 1.958008] pci 0000:00:1b.0: reg 10: [mem 0xf7c28000-0xf7c2bfff 64bit]
[ 1.958079] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.958105] pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
[ 1.958187] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.958214] pci 0000:00:1c.1: [8086:1c12] type 1 class 0x000604
[ 1.958296] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 1.958324] pci 0000:00:1c.2: [8086:1c14] type 1 class 0x000604
[ 1.958406] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 1.958432] pci 0000:00:1c.3: [8086:2448] type 1 class 0x000604
[ 1.958514] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 1.958544] pci 0000:00:1c.4: [8086:1c18] type 1 class 0x000604
[ 1.958674] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 1.958717] pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
[ 1.958740] pci 0000:00:1d.0: reg 10: [mem 0xf7c2f000-0xf7c2f3ff]
[ 1.958834] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.958862] pci 0000:00:1f.0: [8086:1c4f] type 0 class 0x000601
[ 1.958992] pci 0000:00:1f.2: [8086:1c03] type 0 class 0x000106
[ 1.959012] pci 0000:00:1f.2: reg 10: [io 0xe0d0-0xe0d7]
[ 1.959020] pci 0000:00:1f.2: reg 14: [io 0xe0c0-0xe0c3]
[ 1.959029] pci 0000:00:1f.2: reg 18: [io 0xe0b0-0xe0b7]
[ 1.959037] pci 0000:00:1f.2: reg 1c: [io 0xe0a0-0xe0a3]
[ 1.959046] pci 0000:00:1f.2: reg 20: [io 0xe060-0xe07f]
[ 1.959054] pci 0000:00:1f.2: reg 24: [mem 0xf7c2e000-0xf7c2e7ff]
[ 1.959101] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.959121] pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
[ 1.959138] pci 0000:00:1f.3: reg 10: [mem 0xf7c2d000-0xf7c2d0ff 64bit]
[ 1.959160] pci 0000:00:1f.3: reg 20: [io 0xe040-0xe05f]
[ 1.959199] pci 0000:00:1f.6: [8086:1c24] type 0 class 0x001180
[ 1.959221] pci 0000:00:1f.6: reg 10: [mem 0xf7c2c000-0xf7c2cfff 64bit]
[ 1.959341] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 1.959346] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 1.959350] pci 0000:00:1c.0: bridge window [mem 0xf7b00000-0xf7bfffff]
[ 1.959357] pci 0000:00:1c.0: bridge window [mem 0xf2700000-0xf27fffff 64bit pref]
[ 1.959435] pci 0000:02:00.0: [1033:0194] type 0 class 0x000c03
[ 1.959480] pci 0000:02:00.0: reg 10: [mem 0xf7a00000-0xf7a01fff 64bit]
[ 1.959674] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.961362] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 1.961372] pci 0000:00:1c.1: bridge window [io 0xc000-0xcfff]
[ 1.961382] pci 0000:00:1c.1: bridge window [mem 0xf7a00000-0xf7afffff]
[ 1.961398] pci 0000:00:1c.1: bridge window [mem 0xf2500000-0xf25fffff 64bit pref]
[ 1.961589] pci 0000:03:00.0: [8086:0082] type 0 class 0x000280
[ 1.961753] pci 0000:03:00.0: reg 10: [mem 0xf7900000-0xf7901fff 64bit]
[ 1.962493] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 1.964423] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 1.964427] pci 0000:00:1c.2: bridge window [io 0xb000-0xbfff]
[ 1.964432] pci 0000:00:1c.2: bridge window [mem 0xf7900000-0xf79fffff]
[ 1.964438] pci 0000:00:1c.2: bridge window [mem 0xf2300000-0xf23fffff 64bit pref]
[ 1.964559] pci 0000:04:00.0: [1180:e476] type 2 class 0x000607
[ 1.964586] pci 0000:04:00.0: reg 10: [mem 0xf6c00000-0xf6c00fff]
[ 1.964677] pci 0000:04:00.0: supports D1 D2
[ 1.964679] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.966435] pci 0000:00:1c.3: PCI bridge to [bus 04-0c] (subtractive decode)
[ 1.966440] pci 0000:00:1c.3: bridge window [io 0x8000-0x9fff]
[ 1.966444] pci 0000:00:1c.3: bridge window [mem 0xf5800000-0xf77fffff]
[ 1.966451] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 1.966453] pci 0000:00:1c.3: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 1.966455] pci 0000:00:1c.3: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 1.966457] pci 0000:00:1c.3: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 1.966459] pci 0000:00:1c.3: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[ 1.966461] pci 0000:00:1c.3: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[ 1.966463] pci 0000:00:1c.3: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[ 1.966465] pci 0000:00:1c.3: bridge window [mem 0xdfa00000-0xfeafffff] (subtractive decode)
[ 1.966467] pci 0000:00:1c.3: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 1.966578] pci_bus 0000:40: [bus 40-43] partially hidden behind transparent bridge 0000:04 [bus 04-0c]
[ 1.966728] pci 0000:0d:00.0: [10ec:5209] type 0 class 0x00ff00
[ 1.966790] pci 0000:0d:00.0: reg 10: [mem 0xf7801000-0xf7801fff]
[ 1.967272] pci 0000:0d:00.0: supports D1 D2
[ 1.967273] pci 0000:0d:00.0: PME# supported from D1 D2 D3hot
[ 1.967435] pci 0000:0d:00.1: [10ec:5209] type 0 class 0x000805
[ 1.967496] pci 0000:0d:00.1: reg 10: [mem 0xf7800000-0xf78000ff]
[ 1.967988] pci 0000:0d:00.1: supports D1 D2
[ 1.967989] pci 0000:0d:00.1: PME# supported from D1 D2 D3hot
[ 1.969414] pci 0000:00:1c.4: PCI bridge to [bus 0d-0d]
[ 1.969418] pci 0000:00:1c.4: bridge window [io 0xa000-0xafff]
[ 1.969423] pci 0000:00:1c.4: bridge window [mem 0xf7800000-0xf78fffff]
[ 1.969429] pci 0000:00:1c.4: bridge window [mem 0xf2100000-0xf21fffff 64bit pref]
[ 1.969455] pci_bus 0000:00: on NUMA node 0
[ 1.969458] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.969664] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 1.969705] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 1.969746] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 1.969789] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 1.969834] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 1.970130] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 1.970608] pci0000:00: ACPI _OSC control (0x1d) granted
[ 1.975423] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.975469] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 10 11 12 14 15)
[ 1.975512] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.975558] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 1.975602] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 1.975645] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.975689] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 10 11 12 14 15)
[ 1.975731] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 1.975794] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.975803] vgaarb: loaded
[ 1.975804] vgaarb: bridge control possible 0000:00:02.0
[ 1.975860] PCI: Using ACPI for IRQ routing
[ 1.977847] PCI: pci_cache_line_size set to 64 bytes
[ 1.977856] pci 0000:00:04.0: no compatible bridge window for [mem 0xfed98000-0xfed9ffff 64bit]
[ 1.977958] reserve RAM buffer: 000000000009e800 - 000000000009ffff
[ 1.977960] reserve RAM buffer: 00000000dac34000 - 00000000dbffffff
[ 1.977964] reserve RAM buffer: 00000000dad9e000 - 00000000dbffffff
[ 1.977967] reserve RAM buffer: 00000000dada1000 - 00000000dbffffff
[ 1.977969] reserve RAM buffer: 00000000daf3a000 - 00000000dbffffff
[ 1.977972] reserve RAM buffer: 00000000dafec000 - 00000000dbffffff
[ 1.978056] NetLabel: Initializing
[ 1.978057] NetLabel: domain hash size = 128
[ 1.978058] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.978067] NetLabel: unlabeled traffic allowed by default
[ 1.978077] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.978082] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 1.980100] Switching to clocksource hpet
[ 1.984959] pnp: PnP ACPI init
[ 1.984970] ACPI: bus type pnp registered
[ 1.985172] pnp 00:00: [bus 00-3e]
[ 1.985175] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 1.985177] pnp 00:00: [io 0x0cf8-0x0cff]
[ 1.985178] pnp 00:00: [io 0x0d00-0xffff window]
[ 1.985180] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 1.985182] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 1.985184] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 1.985186] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 1.985188] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 1.985189] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 1.985191] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 1.985193] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 1.985195] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 1.985197] pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
[ 1.985199] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 1.985250] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 2.029608] pnp 00:01: [mem 0x000cf200-0x000cf7ff]
[ 2.029610] pnp 00:01: [mem 0x000d0800-0x000d3fff]
[ 2.029649] system 00:01: [mem 0x000cf200-0x000cf7ff] has been reserved
[ 2.029651] system 00:01: [mem 0x000d0800-0x000d3fff] has been reserved
[ 2.029654] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.029679] pnp 00:02: [io 0x0000-0x001f]
[ 2.029680] pnp 00:02: [io 0x0081-0x0091]
[ 2.029682] pnp 00:02: [io 0x0093-0x009f]
[ 2.029683] pnp 00:02: [io 0x00c0-0x00df]
[ 2.029685] pnp 00:02: [dma 4]
[ 2.029702] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 2.029767] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 2.029784] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 2.029793] pnp 00:04: [io 0x00f0]
[ 2.029795] pnp 00:04: [irq 13]
[ 2.029812] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 2.029821] pnp 00:05: [io 0x0061]
[ 2.029822] pnp 00:05: [io 0x0063]
[ 2.029824] pnp 00:05: [io 0x0065]
[ 2.029825] pnp 00:05: [io 0x0067]
[ 2.029826] pnp 00:05: [io 0x0080]
[ 2.029828] pnp 00:05: [io 0x0092]
[ 2.029829] pnp 00:05: [io 0x00b2-0x00b3]
[ 2.029831] pnp 00:05: [io 0x1000-0x100f]
[ 2.029832] pnp 00:05: [io 0xffff]
[ 2.029834] pnp 00:05: [io 0xffff]
[ 2.029835] pnp 00:05: [io 0x0400-0x0453]
[ 2.029837] pnp 00:05: [io 0x0458-0x047f]
[ 2.029838] pnp 00:05: [io 0x0500-0x057f]
[ 2.029840] pnp 00:05: [io 0x0900-0x097f]
[ 2.029875] system 00:05: [io 0x1000-0x100f] has been reserved
[ 2.029877] system 00:05: [io 0xffff] has been reserved
[ 2.029879] system 00:05: [io 0xffff] has been reserved
[ 2.029881] system 00:05: [io 0x0400-0x0453] has been reserved
[ 2.029883] system 00:05: [io 0x0458-0x047f] has been reserved
[ 2.029885] system 00:05: [io 0x0500-0x057f] has been reserved
[ 2.029887] system 00:05: [io 0x0900-0x097f] has been reserved
[ 2.029889] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.029896] pnp 00:06: [io 0x0070-0x0077]
[ 2.029898] pnp 00:06: [irq 8]
[ 2.029915] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 2.029932] pnp 00:07: [io 0x0454-0x0457]
[ 2.029962] system 00:07: [io 0x0454-0x0457] has been reserved
[ 2.029964] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 2.030137] pnp 00:08: [io 0x0060]
[ 2.030140] pnp 00:08: [io 0x0064]
[ 2.030142] pnp 00:08: [irq 1]
[ 2.030163] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 2.037354] pnp 00:09: [irq 12]
[ 2.037393] pnp 00:09: Plug and Play ACPI device, IDs SYN0502 PNP0f13 (active)
[ 2.037418] pnp 00:0a: [io 0x004e-0x004f]
[ 2.037419] pnp 00:0a: [mem 0xfed40000-0xfed44fff]
[ 2.037439] pnp 00:0a: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 2.037649] pnp 00:0b: [mem 0xfed1c000-0xfed1ffff]
[ 2.037651] pnp 00:0b: [mem 0xfed10000-0xfed17fff]
[ 2.037652] pnp 00:0b: [mem 0xfed18000-0xfed18fff]
[ 2.037654] pnp 00:0b: [mem 0xfed19000-0xfed19fff]
[ 2.037655] pnp 00:0b: [mem 0xf8000000-0xfbffffff]
[ 2.037657] pnp 00:0b: [mem 0xfed20000-0xfed3ffff]
[ 2.037659] pnp 00:0b: [mem 0xfed90000-0xfed93fff]
[ 2.037660] pnp 00:0b: [mem 0xfed45000-0xfed8ffff]
[ 2.037662] pnp 00:0b: [mem 0xff000000-0xffffffff]
[ 2.037664] pnp 00:0b: [mem 0xfee00000-0xfeefffff]
[ 2.037665] pnp 00:0b: [mem 0xfed08000-0xfed08fff]
[ 2.037718] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 2.037720] system 00:0b: [mem 0xfed10000-0xfed17fff] could not be reserved
[ 2.037722] system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved
[ 2.037724] system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved
[ 2.037727] system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
[ 2.037729] system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 2.037731] system 00:0b: [mem 0xfed90000-0xfed93fff] has been reserved
[ 2.037733] system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 2.037735] system 00:0b: [mem 0xff000000-0xffffffff] could not be reserved
[ 2.037737] system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 2.037739] system 00:0b: [mem 0xfed08000-0xfed08fff] has been reserved
[ 2.037742] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.037760] pnp 00:0c: [mem 0x000e0000-0x000effff]
[ 2.037762] pnp 00:0c: [mem 0x000f0000-0x000fffff]
[ 2.037807] system 00:0c: [mem 0x000e0000-0x000effff] could not be reserved
[ 2.037809] system 00:0c: [mem 0x000f0000-0x000fffff] could not be reserved
[ 2.037812] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.037914] pnp 00:0d: [mem 0x20000000-0x201fffff]
[ 2.037915] pnp 00:0d: [mem 0x40000000-0x401fffff]
[ 2.037963] system 00:0d: [mem 0x20000000-0x201fffff] has been reserved
[ 2.037965] system 00:0d: [mem 0x40000000-0x401fffff] has been reserved
[ 2.037967] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 2.038015] pnp 00:0e: [mem 0xfed98000-0xfed9ffff]
[ 2.038064] system 00:0e: [mem 0xfed98000-0xfed9ffff] has been reserved
[ 2.038067] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.038080] pnp: PnP ACPI: found 15 devices
[ 2.038081] ACPI: ACPI bus type pnp unregistered
[ 2.038083] PnPBIOS: Disabled
[ 2.074428] PCI: max bus depth: 2 pci_try_num: 3
[ 2.074481] pci 0000:00:04.0: BAR 0: assigned [mem 0xdfa00000-0xdfa07fff 64bit]
[ 2.074484] pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
[ 2.074491] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 2.074495] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 2.074500] pci 0000:00:1c.0: bridge window [mem 0xf7b00000-0xf7bfffff]
[ 2.074505] pci 0000:00:1c.0: bridge window [mem 0xf2700000-0xf27fffff 64bit pref]
[ 2.074512] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 2.074515] pci 0000:00:1c.1: bridge window [io 0xc000-0xcfff]
[ 2.074521] pci 0000:00:1c.1: bridge window [mem 0xf7a00000-0xf7afffff]
[ 2.074525] pci 0000:00:1c.1: bridge window [mem 0xf2500000-0xf25fffff 64bit pref]
[ 2.074532] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 2.074535] pci 0000:00:1c.2: bridge window [io 0xb000-0xbfff]
[ 2.074541] pci 0000:00:1c.2: bridge window [mem 0xf7900000-0xf79fffff]
[ 2.074545] pci 0000:00:1c.2: bridge window [mem 0xf2300000-0xf23fffff 64bit pref]
[ 2.074557] pci 0000:04:00.0: BAR 16: can't assign mem (size 0x4000000)
[ 2.074564] pci 0000:04:00.0: BAR 15: can't assign mem pref (size 0x4000000)
[ 2.074566] pci 0000:04:00.0: BAR 14: assigned [io 0x8000-0x80ff]
[ 2.074568] pci 0000:04:00.0: BAR 13: assigned [io 0x8400-0x84ff]
[ 2.074570] pci 0000:04:00.0: CardBus bridge to [bus 40-43]
[ 2.074572] pci 0000:04:00.0: bridge window [io 0x8400-0x84ff]
[ 2.074578] pci 0000:04:00.0: bridge window [io 0x8000-0x80ff]
[ 2.074584] pci 0000:00:1c.3: PCI bridge to [bus 04-0c]
[ 2.074587] pci 0000:00:1c.3: bridge window [io 0x8000-0x9fff]
[ 2.074593] pci 0000:00:1c.3: bridge window [mem 0xf5800000-0xf77fffff]
[ 2.074597] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 2.074604] pci 0000:00:1c.4: PCI bridge to [bus 0d-0d]
[ 2.074607] pci 0000:00:1c.4: bridge window [io 0xa000-0xafff]
[ 2.074612] pci 0000:00:1c.4: bridge window [mem 0xf7800000-0xf78fffff]
[ 2.074617] pci 0000:00:1c.4: bridge window [mem 0xf2100000-0xf21fffff 64bit pref]
[ 2.074692] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 2.074694] PCI: setting IRQ 11 as level-triggered
[ 2.074753] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
[ 2.074755] PCI: setting IRQ 4 as level-triggered
[ 2.074809] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 2.074861] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[ 2.074863] PCI: setting IRQ 10 as level-triggered
[ 2.074883] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 2.074885] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 2.074887] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 2.074889] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff]
[ 2.074891] pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff]
[ 2.074893] pci_bus 0000:00: resource 9 [mem 0x000dc000-0x000dffff]
[ 2.074895] pci_bus 0000:00: resource 10 [mem 0xdfa00000-0xfeafffff]
[ 2.074897] pci_bus 0000:00: resource 11 [mem 0xfed40000-0xfed44fff]
[ 2.074899] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 2.074900] pci_bus 0000:01: resource 1 [mem 0xf7b00000-0xf7bfffff]
[ 2.074902] pci_bus 0000:01: resource 2 [mem 0xf2700000-0xf27fffff 64bit pref]
[ 2.074904] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
[ 2.074906] pci_bus 0000:02: resource 1 [mem 0xf7a00000-0xf7afffff]
[ 2.074908] pci_bus 0000:02: resource 2 [mem 0xf2500000-0xf25fffff 64bit pref]
[ 2.074910] pci_bus 0000:03: resource 0 [io 0xb000-0xbfff]
[ 2.074912] pci_bus 0000:03: resource 1 [mem 0xf7900000-0xf79fffff]
[ 2.074913] pci_bus 0000:03: resource 2 [mem 0xf2300000-0xf23fffff 64bit pref]
[ 2.074915] pci_bus 0000:04: resource 0 [io 0x8000-0x9fff]
[ 2.074917] pci_bus 0000:04: resource 1 [mem 0xf5800000-0xf77fffff]
[ 2.074919] pci_bus 0000:04: resource 2 [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 2.074921] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 2.074923] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 2.074924] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 2.074926] pci_bus 0000:04: resource 7 [mem 0x000d4000-0x000d7fff]
[ 2.074928] pci_bus 0000:04: resource 8 [mem 0x000d8000-0x000dbfff]
[ 2.074930] pci_bus 0000:04: resource 9 [mem 0x000dc000-0x000dffff]
[ 2.074932] pci_bus 0000:04: resource 10 [mem 0xdfa00000-0xfeafffff]
[ 2.074934] pci_bus 0000:04: resource 11 [mem 0xfed40000-0xfed44fff]
[ 2.074935] pci_bus 0000:40: resource 0 [io 0x8400-0x84ff]
[ 2.074937] pci_bus 0000:40: resource 1 [io 0x8000-0x80ff]
[ 2.074939] pci_bus 0000:0d: resource 0 [io 0xa000-0xafff]
[ 2.074941] pci_bus 0000:0d: resource 1 [mem 0xf7800000-0xf78fffff]
[ 2.074943] pci_bus 0000:0d: resource 2 [mem 0xf2100000-0xf21fffff 64bit pref]
[ 2.074971] NET: Registered protocol family 2
[ 2.075024] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 2.075151] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 2.075423] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 2.075537] TCP: Hash tables configured (established 131072 bind 65536)
[ 2.075539] TCP reno registered
[ 2.075541] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.075547] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.075609] NET: Registered protocol family 1
[ 2.075619] pci 0000:00:02.0: Boot video device
[ 2.248179] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[ 2.420889] pci 0000:02:00.0: power state changed by ACPI to D0
[ 2.420894] pci 0000:02:00.0: power state changed by ACPI to D0
[ 2.420945] PCI: CLS 64 bytes, default 64
[ 2.420987] Trying to unpack rootfs image as initramfs...
[ 3.704332] Freeing initrd memory: 16000k freed
[ 3.707260] apm: BIOS not found.
[ 3.707407] audit: initializing netlink socket (disabled)
[ 3.707417] type=2000 audit(1337694438.528:1): initialized
[ 3.721302] highmem bounce pool size: 64 pages
[ 3.721306] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 3.722699] VFS: Disk quotas dquot_6.5.2
[ 3.722748] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.722868] msgmni has been set to 1571
[ 3.723036] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.723062] io scheduler noop registered
[ 3.723064] io scheduler deadline registered
[ 3.723069] io scheduler cfq registered (default)
[ 3.723210] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 3.723320] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[ 3.723425] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[ 3.723528] pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X
[ 3.723621] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 3.723626] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 3.723643] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[ 3.723645] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 3.723650] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[ 3.723666] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[ 3.723668] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 3.723673] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
[ 3.723689] pcieport 0000:00:1c.4: Signaling PME through PCIe PME interrupt
[ 3.723691] pci 0000:0d:00.0: Signaling PME through PCIe PME interrupt
[ 3.723693] pci 0000:0d:00.1: Signaling PME through PCIe PME interrupt
[ 3.723697] pcie_pme 0000:00:1c.4:pcie01: service driver pcie_pme loaded
[ 3.723739] vesafb: mode is 800x600x16, linelength=1600, pages=67
[ 3.723740] vesafb: scrolling: redraw
[ 3.723742] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 3.723966] vesafb: framebuffer at 0xe0000000, mapped to 0xf4180000, using 1875k, total 65472k
[ 3.724007] fbcon: VESA VGA (fb0) is primary device
[ 3.740592] Console: switching to colour frame buffer device 100x37
[ 3.756932] fb0: VESA VGA frame buffer device
[ 3.756960] intel_idle: MWAIT substates: 0x21120
[ 3.756962] intel_idle: v0.4 model 0x2A
[ 3.756963] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 3.756991] GHES: HEST is not enabled!
[ 3.757037] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 3.757058] isapnp: Scanning for PnP cards...
[ 3.777796] 0000:00:16.3: ttyS0 at I/O 0xe0e0 (irq = 10) is a 16550A
[ 3.777992] Linux agpgart interface v0.103
[ 3.778106] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[ 3.778172] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 3.779076] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 3.779173] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 3.780359] brd: module loaded
[ 3.780455] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 3.791525] i8042: Detected active multiplexing controller, rev 1.0
[ 3.798736] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.798742] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 3.798763] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 3.798778] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 3.798792] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 3.798868] mousedev: PS/2 mouse device common for all mice
[ 3.798974] rtc_cmos 00:06: RTC can wake from S4
[ 3.799086] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 3.799109] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 3.799192] cpuidle: using governor ladder
[ 3.799286] cpuidle: using governor menu
[ 3.799493] TCP cubic registered
[ 3.799495] Registering the dns_resolver key type
[ 3.799511] Using IPI No-Shortcut mode
[ 3.799592] PM: Checking hibernation image partition UUID=d8293c01-7d70-4e9b-b1f4-a661d7dc0fe4
[ 3.804431] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 4.071401] isapnp: No Plug & Play device found
[ 4.469730] psmouse serio2: synaptics: Touchpad model: 1, fw: 6.2, id: 0x39a0b2, caps: 0xa04751/0x200000/0x0
[ 4.518850] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input1
[ 4.522197] PM: Hibernation image not present or could not be loaded.
[ 4.522217] registered taskstats version 1
[ 4.522707] Magic number: 12:261:787
[ 4.522769] rtc_cmos 00:06: setting system clock to 2012-05-22 13:47:19 UTC (1337694439)
[ 4.522772] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[ 4.523044] Freeing unused kernel memory: 556k freed
[ 4.523212] Write protecting the kernel text: 3824k
[ 4.523266] Write protecting the kernel read-only data: 1696k
[ 4.550396] SCSI subsystem initialized
[ 4.563495] mpt2sas version 12.100.00.00 loaded
[ 4.577698] libata version 3.00 loaded.
[ 4.581016] ahci 0000:00:1f.2: version 3.0
[ 4.581077] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[ 4.581110] ahci: SSS flag set, parallel bus scan disabled
[ 4.581135] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3 impl SATA mode
[ 4.581138] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems apst
[ 4.581143] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.583527] scsi0 : ahci
[ 4.583658] scsi1 : ahci
[ 4.583790] scsi2 : ahci
[ 4.583877] scsi3 : ahci
[ 4.583962] scsi4 : ahci
[ 4.584023] scsi5 : ahci
[ 4.584315] ata1: SATA max UDMA/133 abar m2048@0xf7c2e000 port 0xf7c2e100 irq 44
[ 4.584319] ata2: SATA max UDMA/133 abar m2048@0xf7c2e000 port 0xf7c2e180 irq 44
[ 4.584320] ata3: DUMMY
[ 4.584322] ata4: DUMMY
[ 4.584323] ata5: DUMMY
[ 4.584324] ata6: DUMMY
[ 4.706908] Refined TSC clocksource calibration: 2494.333 MHz.
[ 4.706918] Switching to clocksource tsc
[ 4.888754] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.889389] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 4.889404] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 4.944152] ata1.00: ATA-8: TOSHIBA MK3276GSX, GS001W, max UDMA/100
[ 4.944163] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 4.945204] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 4.945216] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 4.946121] ata1.00: configured for UDMA/100
[ 4.946356] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK3276GS GS00 PQ: 0 ANSI: 5
[ 5.251263] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.254269] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 5.254274] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 5.256263] ata2.00: ATAPI: MATSHITADVD-RAM UJ869AS, 1.01, max UDMA/33
[ 5.260133] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 5.260149] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 5.262233] ata2.00: configured for UDMA/33
[ 5.266428] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ869AS 1.01 PQ: 0 ANSI: 5
[ 5.272338] dracut: dracut-017-14.mga2
[ 5.288985] device-mapper: uevent: version 1.0.3
[ 5.289069] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 5.295206] udevd[132]: starting version 181
[ 5.320838] [drm] Initialized drm 1.1.0 20060810
[ 5.324470] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 5.325658] ACPI: Lid Switch [LID]
[ 5.325704] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 5.325708] ACPI: Power Button [PWRB]
[ 5.325741] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 5.325744] ACPI: Power Button [PWRF]
[ 5.352206] i915 0000:00:02.0: setting latency timer to 64
[ 5.367929] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 5.367932] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 5.368133] i915 0000:00:02.0: irq 45 for MSI/MSI-X
[ 5.368140] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.368142] [drm] Driver supports precise vblank timestamp query.
[ 5.368173] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 5.790443] checking generic (e0000000 3ff0000) vs hw (e0000000 10000000)
[ 5.790449] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 5.790465] Console: switching to colour dummy device 80x25
[ 5.790814] fbcon: inteldrmfb (fb0) is primary device
[ 5.791063] [drm] Changing LVDS panel from (+hsync, +vsync) to (-hsync, -vsync)
[ 6.128097] Console: switching to colour frame buffer device 160x50
[ 6.197338] fb0: inteldrmfb frame buffer device
[ 6.197339] drm: registered panic notifier
[ 6.202310] acpi device:33: registered as cooling_device0
[ 6.202536] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 6.202542] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 6.202567] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 6.256144] dracut: Starting plymouth daemon
[ 7.731141] yenta_cardbus 0000:04:00.0: CardBus bridge found [10f7:8338]
[ 7.731180] yenta_cardbus 0000:04:00.0: address space collision: [mem 0xf0000000-0xf13fffff] conflicts with PCI Bus 0000:04 [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 7.731184] yenta_cardbus 0000:04:00.0: Preassigned resource 3 busy or not available, reconfiguring...
[ 7.731189] yenta_cardbus 0000:04:00.0: CardBus bridge to [bus 40-43]
[ 7.731192] yenta_cardbus 0000:04:00.0: bridge window [io 0x8400-0x84ff]
[ 7.731199] yenta_cardbus 0000:04:00.0: bridge window [io 0x8000-0x80ff]
[ 7.731207] yenta_cardbus 0000:04:00.0: bridge window [mem 0xf5800000-0xf6bfffff pref]
[ 7.731215] yenta_cardbus 0000:04:00.0: bridge window [mem 0xf7000000-0xf73fffff]
[ 7.743841] usbcore: registered new interface driver usbfs
[ 7.743867] usbcore: registered new interface driver hub
[ 7.749282] usbcore: registered new device driver usb
[ 7.749287] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 7.749347] sd 0:0:0:0: [sda] Write Protect is off
[ 7.749351] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.749375] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.750888] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 7.750892] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 7.751030] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 7.752803] sdhci: Secure Digital Host Controller Interface driver
[ 7.752805] sdhci: Copyright(c) Pierre Ossman
[ 7.754585] rts_pstor: module is from the staging directory, the quality is unknown, you have been warned.
[ 7.755185] Initializing Realtek PCIE storage driver...
[ 7.755260] Resource length: 0x1000
[ 7.755271] Original address: 0xf7801000, remapped address: 0xf410e000
[ 7.755274] pci->irq = 11
[ 7.755275] rtsx_acquire_irq: chip->msi_en = 0, pci->irq = 11
[ 7.764468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.764539] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 7.764544] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 7.764575] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 7.764601] ehci_hcd 0000:00:1a.0: debug port 2
[ 7.768489] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 7.768498] ehci_hcd 0000:00:1a.0: irq 11, io mem 0xf7c30000
[ 7.774925] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 7.774978] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.774981] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.774983] usb usb1: Product: EHCI Host Controller
[ 7.774985] usb usb1: Manufacturer: Linux 3.3.6-desktop586-2.mga2 ehci_hcd
[ 7.774987] usb usb1: SerialNumber: 0000:00:1a.0
[ 7.775086] hub 1-0:1.0: USB hub found
[ 7.775090] hub 1-0:1.0: 3 ports detected
[ 7.775171] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 7.775175] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 7.775181] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 7.775203] ehci_hcd 0000:00:1d.0: debug port 2
[ 7.779094] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 7.779101] ehci_hcd 0000:00:1d.0: irq 10, io mem 0xf7c2f000
[ 7.784887] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 7.784941] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.784944] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.784945] usb usb2: Product: EHCI Host Controller
[ 7.784947] usb usb2: Manufacturer: Linux 3.3.6-desktop586-2.mga2 ehci_hcd
[ 7.784948] usb usb2: SerialNumber: 0000:00:1d.0
[ 7.785029] hub 2-0:1.0: USB hub found
[ 7.785032] hub 2-0:1.0: 3 ports detected
[ 7.853419] yenta_cardbus 0000:04:00.0: ISA IRQ mask 0x0000, PCI irq 10
[ 7.853424] yenta_cardbus 0000:04:00.0: Socket status: 30000006
[ 7.853427] pci_bus 0000:40: Upper limit for fixing this bridge's parent bridge: #0c
[ 7.853432] yenta_cardbus 0000:04:00.0: pcmcia: parent PCI bridge window: [io 0x8000-0x9fff]
[ 7.853435] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x8000-0x9fff: excluding 0x8000-0x80ff 0x8400-0x84ff
[ 7.873529] yenta_cardbus 0000:04:00.0: pcmcia: parent PCI bridge window: [mem 0xf5800000-0xf77fffff]
[ 7.873532] pcmcia_socket pcmcia_socket0: cs: memory probe 0xf5800000-0xf77fffff: excluding 0xf5800000-0xf6dfffff 0xf7000000-0xf73fffff
[ 7.873542] yenta_cardbus 0000:04:00.0: pcmcia: parent PCI bridge window: [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 7.873544] pcmcia_socket pcmcia_socket0: cs: memory probe 0xf0000000-0xf1ffffff: excluding 0xf0000000-0xf1ffffff
[ 7.911483] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
[ 7.912573] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.920967] xhci_hcd 0000:02:00.0: power state changed by ACPI to D0
[ 7.920973] xhci_hcd 0000:02:00.0: power state changed by ACPI to D0
[ 7.921003] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 7.921015] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 7.921184] xhci_hcd 0000:02:00.0: irq 4, io mem 0xf7a00000
[ 7.921251] xhci_hcd 0000:02:00.0: irq 46 for MSI/MSI-X
[ 7.921257] xhci_hcd 0000:02:00.0: irq 47 for MSI/MSI-X
[ 7.921262] xhci_hcd 0000:02:00.0: irq 48 for MSI/MSI-X
[ 7.921267] xhci_hcd 0000:02:00.0: irq 49 for MSI/MSI-X
[ 7.921273] xhci_hcd 0000:02:00.0: irq 50 for MSI/MSI-X
[ 7.921391] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.921393] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.921395] usb usb3: Product: xHCI Host Controller
[ 7.921396] usb usb3: Manufacturer: Linux 3.3.6-desktop586-2.mga2 xhci_hcd
[ 7.921398] usb usb3: SerialNumber: 0000:02:00.0
[ 7.921477] xHCI xhci_add_endpoint called for root hub
[ 7.921480] xHCI xhci_check_bandwidth called for root hub
[ 7.921513] hub 3-0:1.0: USB hub found
[ 7.921522] hub 3-0:1.0: 2 ports detected
[ 7.921583] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 7.921588] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[ 7.924598] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 7.924600] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.924602] usb usb4: Product: xHCI Host Controller
[ 7.924604] usb usb4: Manufacturer: Linux 3.3.6-desktop586-2.mga2 xhci_hcd
[ 7.924605] usb usb4: SerialNumber: 0000:02:00.0
[ 7.924672] xHCI xhci_add_endpoint called for root hub
[ 7.924674] xHCI xhci_check_bandwidth called for root hub
[ 7.924712] hub 4-0:1.0: USB hub found
[ 7.924721] hub 4-0:1.0: 2 ports detected
[ 7.955914] scsi6 : SCSI emulation for PCI-Express Mass Storage devices
[ 7.955998] rts_pstor: waiting for device to settle before scanning
[ 7.956027] sdhci-pci 0000:0d:00.1: SDHCI controller found [10ec:5209] (rev 1)
[ 7.956081] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 7.956099] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 7.956142] Registered led device: mmc0::
[ 7.956175] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 7.957655] mmc0: SDHCI controller on PCI [0000:0d:00.1] using DMA
[ 7.985948] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 8.016117] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 8.046046] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 8.076094] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 8.076556] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 8.190768] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 8.190772] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 8.191047] hub 1-1:1.0: USB hub found
[ 8.191140] hub 1-1:1.0: 6 ports detected
[ 8.293217] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[ 8.407488] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 8.407498] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 8.407761] hub 2-1:1.0: USB hub found
[ 8.407847] hub 2-1:1.0: 8 ports detected
[ 8.482155] usb 1-1.1: new high-speed USB device number 3 using ehci_hcd
[ 8.568675] usb 1-1.1: config 1 has an invalid interface number: 1 but max is 0
[ 8.568684] usb 1-1.1: config 1 has no interface number 0
[ 8.570519] usb 1-1.1: New USB device found, idVendor=04da, idProduct=250e
[ 8.570526] usb 1-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[ 8.570532] usb 1-1.1: Product: Qualcomm Gobi 2000
[ 8.570537] usb 1-1.1: Manufacturer: Qualcomm Incorporated
[ 8.634973] usb 1-1.2: new full-speed USB device number 4 using ehci_hcd
[ 8.954610] scsi 6:0:0:0: Direct-Access Generic- xD/SD/M.S. 1.00 PQ: 0 ANSI: 0 CCS
[ 8.954816] Bad LUN (0:1)
[ 8.955031] Bad target number (1:0)
[ 8.955071] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 8.955119] Bad target number (2:0)
[ 8.955191] Bad target number (3:0)
[ 8.955389] Bad target number (4:0)
[ 8.955723] Bad target number (5:0)
[ 8.955813] Bad target number (6:0)
[ 8.955888] Bad target number (7:0)
[ 8.955913] rts_pstor: device scan complete
[ 9.038685] usb 1-1.2: New USB device found, idVendor=044e, idProduct=3001
[ 9.038687] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.038689] usb 1-1.2: Product: UGNZ4
[ 9.038691] usb 1-1.2: Manufacturer: ALPS
[ 20.424021] PM: Marking nosave pages: 000000000009e000 - 0000000000100000
[ 20.424026] PM: Marking nosave pages: 0000000020000000 - 0000000020200000
[ 20.424036] PM: Basic memory bitmaps created
[ 20.754275] PM: Basic memory bitmaps freed
[ 20.754286] video LNXVIDEO:00: Restoring backlight state
[ 20.762332] PM: Starting manual resume from disk
[ 20.762335] PM: Hibernation image partition 8:6 present
[ 20.762336] PM: Looking for hibernation image.
[ 20.765452] PM: Image not found (code -22)
[ 20.765455] PM: Hibernation image not present or could not be loaded.
[ 20.788190] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 20.818398] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 20.848518] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 20.862651] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[ 20.878113] sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 21.013035] dracut: Checking ext4: /dev/disk/by-uuid/439c3c53-7383-4574-8d0c-f109cb963969
[ 21.013075] dracut: issuing e2fsck -a /dev/disk/by-uuid/439c3c53-7383-4574-8d0c-f109cb963969
[ 21.070631] dracut: /dev/disk/by-uuid/439c3c53-7383-4574-8d0c-f109cb963969: clean, 211469/1016000 files, 1647567/4063960 blocks
[ 21.070831] dracut: Remounting /dev/disk/by-uuid/439c3c53-7383-4574-8d0c-f109cb963969 with -o ro
[ 21.128818] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[ 21.179854] dracut: Mounted root filesystem /dev/sda9
[ 21.549287] dracut: Switching root
[ 21.550071] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[ 22.315195] NET: Registered protocol family 10
[ 23.485424] udevd[510]: starting version 181
[ 24.780621] EXT4-fs (sda9): re-mounted. Opts: (null)
[ 25.190601] ACPI: AC Adapter [AC] (off-line)
[ 25.278600] ACPI: Battery Slot [BAT1] (battery present)
[ 25.502402] ACPI Warning: 0x0000e040-0x0000e05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120111/utaddress-251)
[ 25.502410] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 25.561304] thermal LNXTHERM:00: registered as thermal_zone0
[ 25.561308] ACPI: Thermal Zone [TZ00] (40 C)
[ 25.564974] thermal LNXTHERM:01: registered as thermal_zone1
[ 25.564977] ACPI: Thermal Zone [TZ01] (40 C)
[ 25.908815] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 25.908820] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 25.908940] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3
[ 25.908944] PCI: setting IRQ 3 as level-triggered
[ 25.909008] snd_hda_intel 0000:00:1b.0: irq 51 for MSI/MSI-X
[ 25.911916] iTCO_vendor_support: vendor-support=0
[ 25.947835] mei: module is from the staging directory, the quality is unknown, you have been warned.
[ 25.953284] input: Panasonic Laptop Support as /devices/virtual/input/input6
[ 26.000372] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 26.000463] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 26.000722] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
[ 26.058255] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 26.061466] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x47f 0x4d0-0x4d7
[ 26.062201] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 26.063260] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 26.064435] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xd3fff 0xe0000-0xfffff
[ 26.064469] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
[ 26.064500] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[ 26.064532] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 26.233918] cfg80211: Calling CRDA to update world regulatory domain
[ 26.252738] e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
[ 26.252741] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 26.407472] Bluetooth: Core ver 2.16
[ 26.407489] NET: Registered protocol family 31
[ 26.407492] Bluetooth: HCI device and connection manager initialized
[ 26.407494] Bluetooth: HCI socket layer initialized
[ 26.407496] Bluetooth: L2CAP socket layer initialized
[ 26.407499] Bluetooth: SCO socket layer initialized
[ 26.564421] tpm_inf_pnp 00:0a: Found TPM with ID IFX0102
[ 26.565992] tpm_tis 00:0a: 1.2 TPM (device-id 0xB, rev-id 16)
[ 26.625004] usbcore: registered new interface driver btusb
[ 26.985275] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:d
[ 26.985278] Copyright(c) 2003-2011 Intel Corporation
[ 26.985336] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000
[ 26.985338] iwlwifi 0000:03:00.0: pci_resource_base = f466c000
[ 26.985339] iwlwifi 0000:03:00.0: HW Revision ID = 0x34
[ 26.985416] iwlwifi 0000:03:00.0: irq 52 for MSI/MSI-X
[ 26.985449] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG enabled
[ 26.985451] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[ 26.985452] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING disabled
[ 26.985454] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE disabled
[ 26.985455] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled
[ 26.985461] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
[ 26.985518] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
[ 26.994542] iwlwifi 0000:03:00.0: device EEPROM VER=0x715, CALIB=0x6
[ 26.994544] iwlwifi 0000:03:00.0: Device SKU: 0x1F0
[ 26.994545] iwlwifi 0000:03:00.0: Valid Tx ant: 0x3, Valid Rx ant: 0x3
[ 26.994559] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[ 27.284815] iwlwifi 0000:03:00.0: loaded firmware version 17.168.5.3 build 42301
[ 27.284978] Registered led device: phy0-led
[ 27.312630] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 27.339588] SKU: Nid=0x1d sku_cfg=0x40159a05
[ 27.339591] SKU: port_connectivity=0x1
[ 27.339593] SKU: enable_pcbeep=0x1
[ 27.339594] SKU: check_sum=0x00000005
[ 27.339596] SKU: customization=0x0000009a
[ 27.339597] SKU: external_amp=0x0
[ 27.339598] SKU: platform_type=0x1
[ 27.339599] SKU: swap=0x0
[ 27.339600] SKU: override=0x1
[ 27.339931] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 27.339932] speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 27.339934] hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 27.339935] mono: mono_out=0x0
[ 27.339936] inputs: Mic=0x18
[ 27.341126] realtek: No valid SSID, checking pincfg 0x40159a05 for NID 0x1d
[ 27.341128] realtek: Enabling init ASM_ID=0x9a05 CODEC_ID=10ec0269
[ 27.561390] cfg80211: World regulatory domain updated:
[ 27.561392] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 27.561395] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 27.561397] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 27.561399] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 27.561401] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 27.561402] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 27.573805] HDMI status: Codec=3 Pin=6 Presence_Detect=0 ELD_Valid=0
[ 27.573878] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 27.573964] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 27.574018] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 27.574301] mei 0000:00:16.0: setting latency timer to 64
[ 27.574377] mei 0000:00:16.0: irq 53 for MSI/MSI-X
[ 27.624827] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5
[ 27.624831] PCI: setting IRQ 5 as level-triggered
[ 27.624845] e1000e 0000:00:19.0: setting latency timer to 64
[ 27.624969] e1000e 0000:00:19.0: irq 54 for MSI/MSI-X
[ 27.661020] watchdog: INTCAMT: cannot register miscdev on minor=130 (err=-16).
[ 27.661027] watchdog: error registering /dev/watchdog (err=-16).
[ 27.661034] mei 0000:00:16.0: unable to register watchdog device.
[ 27.819347] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 70:58:12:dc:3d:fb
[ 27.819351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 27.819385] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
[ 27.829984] cfg80211: Calling CRDA for country: US
[ 27.831638] cfg80211: Regulatory domain changed to country: US
[ 27.831641] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 27.831644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 27.831646] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 27.831648] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 27.831650] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 27.831652] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 27.831653] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 28.707845] tpm_tis 00:0a: A TPM error (7) occurred attempting to read a pcr value
[ 28.707856] tpm_tis 00:0a: TPM is disabled/deactivated (0x7)
[ 28.781676] Non-volatile memory driver v1.3
[ 29.367733] Adding 6080564k swap on /dev/sda6. Priority:0 extents:1 across:6080564k
[ 31.925382] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-06-01 15:47 ` [Bug 43331] " Bjorn Helgaas
2012-06-01 16:22 ` Bill Unruh
@ 2012-06-01 17:04 ` Bill Unruh
1 sibling, 0 replies; 12+ messages in thread
From: Bill Unruh @ 2012-06-01 17:04 UTC (permalink / raw)
To: Bjorn Helgaas; +Cc: linux-kernel, linux-pci, bugzilla-daemon
On testing with the current kernel, running without the noapic seems to be
working, so it might be OK. I will try it for a while and see if I get random
crashes.
On Fri, 1 Jun 2012, Bjorn Helgaas wrote:
> On Thu, May 31, 2012 at 3:39 PM, Bill Unruh <unruh@physics.ubc.ca> wrote:
>> I am running Mageia 2 kernel 3.3.6-desktop586-2.mga2
>>
>> Every time I boot up I get the error messages
>> pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
>
> Thanks very much for this report. I opened this bug report to help me
> keep track of it: https://bugzilla.kernel.org/show_bug.cgi?id=43331
>
> The message means that we tried to write address 0xdfa00000 to BAR 0
> of device 00:04.0 (a "signal processing controller," whatever that
> is), but when we read the BAR back, we read 0xfed98004 instead.
> That's an interesting address because it looks a lot like a resource
> of an ACPI PNP0c02 device:
>
> system 00:0e: [mem 0xfed98000-0xfed9ffff] has been reserved
> system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
>
> You say your machine runs OK (with "noapic"), but I'm doubtful that
> 00:04.0 is working -- it doesn't even seem to have a driver bound to
> it. I don't know what the device does, but if you're not using it,
> it's not surprising that you wouldn't notice it being broken.
>
> Can you attach the complete dmesg log to the bugzilla? It will have
> more details about other devices and the ranges from which we allocate
> resources for PCI devices.
>
> You mention that the machine is not reliable unless you use "noapic".
> That sounds like a separate bug, but also something it would be good
> to track down.
>
--
William G. Unruh | Canadian Institute for| Tel: +1(604)822-3273
Physics&Astronomy | Advanced Research | Fax: +1(604)822-5324
UBC, Vancouver,BC | Program in Cosmology | unruh@physics.ubc.ca
Canada V6T 1Z1 | and Gravity | www.theory.physics.ubc.ca/
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-06-01 16:22 ` Bill Unruh
@ 2012-06-02 3:30 ` Jiang Liu
2012-07-06 18:06 ` Bjorn Helgaas
0 siblings, 1 reply; 12+ messages in thread
From: Jiang Liu @ 2012-06-02 3:30 UTC (permalink / raw)
To: Bill Unruh, Bjorn Helgaas; +Cc: linux-kernel, linux-pci, bugzilla-daemon
Hi Bill and Bjorn,
Device 8086:0103 is "2nd Generation Core Processor Family Thermal Management
Controller" or "Sandy Bridge Thermal Management Controller". And address range
0xfed98000-0xfed9ffff has been reserved by motherboard device(PNP0C02).
I guess that BIOS has assigned address "0xfed98000" to 0000:00:04.0 for
thermal management functionality. The BAR0 of 0000:00:04.0 may be locked down
(can't be changed by OS) because the ACPI BIOS may have dependency on the assigned
address ranges. A ACPI dump may give some help here if convenient.
Thanks!
Gerry
On 06/02/2012 12:22 AM, Bill Unruh wrote:
> Attached is a complete dmesg from a bootup of the kernel on the toughbook S10.
>
>
> RE the noapic, I have no idea how I can give more information on it, since the
> crash almost always occurs during the boot process itself, often very early in
> the process. I will see if I can resurect the dmesg that gets saved, if any,
> during that process. It is probably also an earlier kernel. I have not dared
> try my current kernel with noapic, but perhaps I will try.
>
>
>
> On Fri, 1 Jun 2012, Bjorn Helgaas wrote:
>
>> On Thu, May 31, 2012 at 3:39 PM, Bill Unruh <unruh@physics.ubc.ca> wrote:
>>> I am running Mageia 2 kernel 3.3.6-desktop586-2.mga2
>>>
>>> Every time I boot up I get the error messages
>>> pci 0000:00:04.0: BAR 0: error updating (0xdfa00004 != 0xfed98004)
>>
>> Thanks very much for this report. I opened this bug report to help me
>> keep track of it: https://bugzilla.kernel.org/show_bug.cgi?id=43331
>>
>> The message means that we tried to write address 0xdfa00000 to BAR 0
>> of device 00:04.0 (a "signal processing controller," whatever that
>> is), but when we read the BAR back, we read 0xfed98004 instead.
>> That's an interesting address because it looks a lot like a resource
>> of an ACPI PNP0c02 device:
>>
>> system 00:0e: [mem 0xfed98000-0xfed9ffff] has been reserved
>> system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
>>
>> You say your machine runs OK (with "noapic"), but I'm doubtful that
>> 00:04.0 is working -- it doesn't even seem to have a driver bound to
>> it. I don't know what the device does, but if you're not using it,
>> it's not surprising that you wouldn't notice it being broken.
>>
>> Can you attach the complete dmesg log to the bugzilla? It will have
>> more details about other devices and the ranges from which we allocate
>> resources for PCI devices.
>>
>> You mention that the machine is not reliable unless you use "noapic".
>> That sounds like a separate bug, but also something it would be good
>> to track down.
>>
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-06-02 3:30 ` Jiang Liu
@ 2012-07-06 18:06 ` Bjorn Helgaas
2012-07-06 23:37 ` Bill Unruh
0 siblings, 1 reply; 12+ messages in thread
From: Bjorn Helgaas @ 2012-07-06 18:06 UTC (permalink / raw)
To: Jiang Liu; +Cc: Bill Unruh, linux-kernel, linux-pci, bugzilla-daemon
On Sat, Jun 02, 2012 at 11:30:23AM +0800, Jiang Liu wrote:
> ... address range 0xfed98000-0xfed9ffff has been reserved by motherboard
> device(PNP0C02). I guess that BIOS has assigned address "0xfed98000" to
> 0000:00:04.0 for thermal management functionality. The BAR0 of
> 0000:00:04.0 may be locked down (can't be changed by OS) because the ACPI
> BIOS may have dependency on the assigned address ranges.
I don't think the BAR can be completely read-only. If it were, we wouldn't
have any way to determine its size. We believe it is 32K in size:
pci 0000:00:04.0: reg 10: [mem 0xfed98000-0xfed9ffff 64bit]
so we should have written 0xffffffff to the low 32 bits of the BAR and read
back 0xffff8004 (32K = 2^15, so the low-order 15 bits should be read-only,
including the prefetchable bit (0), the type bits (10 for 64-bit), and the
memory space indicator (0)).
Can you experiment with setting that BAR manually, e.g., by running these
commands as root:
# setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
# setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
# setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
That's basically what the kernel does in pci_update_resource(), so this
will likely fail, too.
In __pci_read_base(), where we size the BAR, we disable decoding first,
which we *don't* do in pci_update_resource(). So if the above doesn't
work, can you try this:
# setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
# setpci -s 00:04.0 COMMAND=0
# setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
# setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-07-06 18:06 ` Bjorn Helgaas
@ 2012-07-06 23:37 ` Bill Unruh
2012-07-07 0:55 ` Yinghai Lu
0 siblings, 1 reply; 12+ messages in thread
From: Bill Unruh @ 2012-07-06 23:37 UTC (permalink / raw)
To: Bjorn Helgaas; +Cc: Jiang Liu, linux-kernel, linux-pci, bugzilla-daemon
On Fri, 6 Jul 2012, Bjorn Helgaas wrote:
> On Sat, Jun 02, 2012 at 11:30:23AM +0800, Jiang Liu wrote:
>> ... address range 0xfed98000-0xfed9ffff has been reserved by motherboard
>> device(PNP0C02). I guess that BIOS has assigned address "0xfed98000" to
>> 0000:00:04.0 for thermal management functionality. The BAR0 of
>> 0000:00:04.0 may be locked down (can't be changed by OS) because the ACPI
>> BIOS may have dependency on the assigned address ranges.
>
> I don't think the BAR can be completely read-only. If it were, we wouldn't
> have any way to determine its size. We believe it is 32K in size:
>
> pci 0000:00:04.0: reg 10: [mem 0xfed98000-0xfed9ffff 64bit]
>
> so we should have written 0xffffffff to the low 32 bits of the BAR and read
> back 0xffff8004 (32K = 2^15, so the low-order 15 bits should be read-only,
> including the prefetchable bit (0), the type bits (10 for 64-bit), and the
> memory space indicator (0)).
>
> Can you experiment with setting that BAR manually, e.g., by running these
> commands as root:
>
> # setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
> # setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
> # setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
planet:0[root]>setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
0006
fed98004
00000000
planet:0[root]>setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
planet:0[root]>setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
fed98004
00000000
planet:0[root]
So it seems to work but does not change the base address (or was that what
you meant by "does not work")
>
> That's basically what the kernel does in pci_update_resource(), so this
> will likely fail, too.
>
> In __pci_read_base(), where we size the BAR, we disable decoding first,
> which we *don't* do in pci_update_resource(). So if the above doesn't
> work, can you try this:
>
> # setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
> # setpci -s 00:04.0 COMMAND=0
> # setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
> # setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
planet:0[root]>setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
0006
fed98004
00000000
planet:0[root]>setpci -s 00:04.0 COMMAND=0
planet:0[root]>setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
planet:0[root]>setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
fed98004
00000000
planet:0[root]>
Ie, same thing-- no change in the address.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-07-06 23:37 ` Bill Unruh
@ 2012-07-07 0:55 ` Yinghai Lu
2012-07-07 7:22 ` Bill Unruh
2012-07-07 13:41 ` Bjorn Helgaas
0 siblings, 2 replies; 12+ messages in thread
From: Yinghai Lu @ 2012-07-07 0:55 UTC (permalink / raw)
To: Bill Unruh
Cc: Bjorn Helgaas, Jiang Liu, linux-kernel, linux-pci, bugzilla-daemon
On Fri, Jul 6, 2012 at 4:37 PM, Bill Unruh <unruh@physics.ubc.ca> wrote:
> On Fri, 6 Jul 2012, Bjorn Helgaas wrote:
>
>> On Sat, Jun 02, 2012 at 11:30:23AM +0800, Jiang Liu wrote:
>>>
>>> ... address range 0xfed98000-0xfed9ffff has been reserved by motherboard
>>> device(PNP0C02).
No, pnp resource reservation is after pci bar reservation.
>>>I guess that BIOS has assigned address "0xfed98000" to
>>> 0000:00:04.0 for thermal management functionality. The BAR0 of
>>> 0000:00:04.0 may be locked down (can't be changed by OS) because the ACPI
>>> BIOS may have dependency on the assigned address ranges.
>>
>>
>> I don't think the BAR can be completely read-only. If it were, we
>> wouldn't
>> have any way to determine its size. We believe it is 32K in size:
>>
>> pci 0000:00:04.0: reg 10: [mem 0xfed98000-0xfed9ffff 64bit]
>>
>> so we should have written 0xffffffff to the low 32 bits of the BAR and
>> read
>> back 0xffff8004 (32K = 2^15, so the low-order 15 bits should be read-only,
>> including the prefetchable bit (0), the type bits (10 for 64-bit), and the
>> memory space indicator (0)).
because it is locked down by BIOS to chipset, readback should be 0xfed98004.
and pci_size will return 32k for 0xfed98000.
>>
>> Can you experiment with setting that BAR manually, e.g., by running these
>> commands as root:
>>
>> # setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
>> # setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
>> # setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
>
>
>
> planet:0[root]>setpci -s 00:04.0 COMMAND BASE_ADDRESS_0 BASE_ADDRESS_1
> 0006
> fed98004
> 00000000
> planet:0[root]>setpci -s 00:04.0 BASE_ADDRESS_0=0xdfa00000
> planet:0[root]>setpci -s 00:04.0 BASE_ADDRESS_0 BASE_ADDRESS_1
> fed98004
> 00000000
> planet:0[root]
BIOS _CRS
[ 1.956431] PCI: Using host bridge windows from ACPI; if necessary,
use "pci=nocrs" and report a bug
[ 1.956921] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 1.957225] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 1.957227] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 1.957229] pci_root PNP0A08:00: host bridge window [mem
0x000a0000-0x000bffff]
[ 1.957232] pci_root PNP0A08:00: host bridge window [mem
0x000d4000-0x000d7fff]
[ 1.957234] pci_root PNP0A08:00: host bridge window [mem
0x000d8000-0x000dbfff]
[ 1.957235] pci_root PNP0A08:00: host bridge window [mem
0x000dc000-0x000dffff]
[ 1.957237] pci_root PNP0A08:00: host bridge window [mem
0xdfa00000-0xfeafffff]
[ 1.957239] pci_root PNP0A08:00: host bridge window [mem
0xfed40000-0xfed44fff]
and it does not include 0xfed98000 for the 00:04.0, so kernel can not
reserve it,
and kernel will reject it and try to get new range for 00:04.0 but
bios lock down
that in chipset setting register.
so try get one update bios that could return resource for root bus.
or you could try to live with booting with pci=nocrs before your get new BIOS.
Thanks
Yinghai
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-07-07 0:55 ` Yinghai Lu
@ 2012-07-07 7:22 ` Bill Unruh
2012-07-07 19:02 ` Yinghai Lu
2012-07-07 13:41 ` Bjorn Helgaas
1 sibling, 1 reply; 12+ messages in thread
From: Bill Unruh @ 2012-07-07 7:22 UTC (permalink / raw)
To: Yinghai Lu
Cc: Bjorn Helgaas, Jiang Liu, linux-kernel, linux-pci, bugzilla-daemon
On Fri, 6 Jul 2012, Yinghai Lu wrote:
>
> so try get one update bios that could return resource for root bus.
>
> or you could try to live with booting with pci=nocrs before your get new BIOS.
Where would I get a new BIOS ? Has Panasonic released a bios update for this
machine that fixes this problem?
I guess the other possibility is to live with the error message, or is this
error part of the reason why my machine has such bad battery use? (less than
1/2 the time that Windows gets on the same machine).
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-07-07 0:55 ` Yinghai Lu
2012-07-07 7:22 ` Bill Unruh
@ 2012-07-07 13:41 ` Bjorn Helgaas
1 sibling, 0 replies; 12+ messages in thread
From: Bjorn Helgaas @ 2012-07-07 13:41 UTC (permalink / raw)
To: Yinghai Lu
Cc: Bill Unruh, Jiang Liu, linux-kernel, linux-pci, bugzilla-daemon
> because it is locked down by BIOS to chipset, readback should be 0xfed98004.
>
> and pci_size will return 32k for 0xfed98000.
A device with a read-only BAR doesn't conform to the PCI spec. We
can't determine how much space the device consumes.
It's just an accident that BIOS put it at an address that we happen to
interpret as 32K. We have no idea if the device consumes 4K, 8K, 16K,
or 32K.
> so try get one update bios that could return resource for root bus.
>
> or you could try to live with booting with pci=nocrs before your get new BIOS.
A BIOS update is not a useful answer. The point is that we need
better reporting of the situation so we don't have to spend all this
time debugging this issue again. We need to figure out how to
identify this as a non spec-compliant device and continue as best we
can. We probably need to report it to the user because if there's a
device of unknown size consuming address space, we're liable to cause
a conflict by placing another device on top of it.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-07-07 7:22 ` Bill Unruh
@ 2012-07-07 19:02 ` Yinghai Lu
2012-07-09 17:26 ` Bjorn Helgaas
0 siblings, 1 reply; 12+ messages in thread
From: Yinghai Lu @ 2012-07-07 19:02 UTC (permalink / raw)
To: Bill Unruh
Cc: Bjorn Helgaas, Jiang Liu, linux-kernel, linux-pci, bugzilla-daemon
On Sat, Jul 7, 2012 at 12:22 AM, Bill Unruh <unruh@physics.ubc.ca> wrote:
> On Fri, 6 Jul 2012, Yinghai Lu wrote:
> Where would I get a new BIOS ? Has Panasonic released a bios update for this
> machine that fixes this problem?
looks like they do not bios update for S10 yet.
http://www.panasonic.com/business/toughbook/computer-support-bios.asp#CF-U1
maybe you can try to email or call their support.
>
> I guess the other possibility is to live with the error message, or is this
> error part of the reason why my machine has such bad battery use? (less than
> 1/2 the time that Windows gets on the same machine).
not sure, You can try to boot with pci=nocrs to see if there is any difference.
Thanks
Yinghai
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [Bug 43331] Re: Bug on bootup of Linux kernel on Panasonic Toughbook S10
2012-07-07 19:02 ` Yinghai Lu
@ 2012-07-09 17:26 ` Bjorn Helgaas
0 siblings, 0 replies; 12+ messages in thread
From: Bjorn Helgaas @ 2012-07-09 17:26 UTC (permalink / raw)
To: Yinghai Lu
Cc: Bill Unruh, Jiang Liu, linux-kernel, linux-pci, bugzilla-daemon
> looks like they do not bios update for S10 yet.
>
> http://www.panasonic.com/business/toughbook/computer-support-bios.asp#CF-U1
>
> maybe you can try to email or call their support.
Please stop suggesting a BIOS upgrade. The BIOS is totally out of our
control, and if the current BIOS works with Windows but not Linux,
99.99% of users will just run Windows. Those users will just give up
on Linux, and we'll never even hear about it.
Fortunately, Bill is a sophisticated user who cared enough to report
the issue, so we have a chance to do something about it. What we need
is for Linux to deal with this situation better, and that *IS* in our
control.
For example, we could detect the BAR being read-only when we size it.
We could use the read-only address to derive the worst-case BAR size
(32K in this case). We could mark it as IORESOURCE_PCI_FIXED and use
that to avoid trying to move it. We could log a message to this
effect so the next time it will take 10 minutes instead of 6 weeks to
diagnose the problem.
The end result for Bill will be the same (an unexpected message while
booting), but we can at least make the message intelligible rather
than "BAR 0: error updating (0xdfa00004 != 0xfed98004)".
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2012-07-09 17:26 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-05-31 21:39 Bug on bootup of Linux kernel on Panasonic Toughbook S10 Bill Unruh
2012-06-01 15:47 ` [Bug 43331] " Bjorn Helgaas
2012-06-01 16:22 ` Bill Unruh
2012-06-02 3:30 ` Jiang Liu
2012-07-06 18:06 ` Bjorn Helgaas
2012-07-06 23:37 ` Bill Unruh
2012-07-07 0:55 ` Yinghai Lu
2012-07-07 7:22 ` Bill Unruh
2012-07-07 19:02 ` Yinghai Lu
2012-07-09 17:26 ` Bjorn Helgaas
2012-07-07 13:41 ` Bjorn Helgaas
2012-06-01 17:04 ` Bill Unruh
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.