* [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC.
@ 2015-11-12 18:09 Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for " Vishnu Patekar
` (10 more replies)
0 siblings, 11 replies; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
This patch series adds basic support for Allwinner A83T SOC.
Allwinner A83T is octa-core cortex-a7 based SoC.
It's clock control unit and prcm, pinmux are different from previous sun8i
series.
Its processor cores are arragned in two clusters 4 cores each,
similar to A80.
Only basic clocks are enabled pll1, pll5, pll6.
SMP, display, other peripherals support is not yet supported.
This enables booting kernel with initramfs, kernel patch v1 have been sent.
I'll send v2 with comments addressed.
Vishnu Patekar (10):
sunxi: Add Machine Support for A83T SOC
sunxi: Add support for UART0 in PB pin group on A83T
sunxi: power: axp818: add support for axp818 driver
sunxi: power: enabled support for axp818
sunxi: do not enable smp for A83T
sunxi: clk: add basic clocks for A83T
sunxi: Add support for Allwinner A83T DRAM
sunxi: do not include display for A83T
sunxi: dts: sun8i: Add Allwinner A83T dtsi
sunxi: Add suport for A83T HomletV2 Board by Allwinner
arch/arm/cpu/armv7/sunxi/Makefile | 7 +
arch/arm/cpu/armv7/sunxi/board.c | 8 +-
arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++
arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 +
arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424 +++++++++++++++++++++
arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +
arch/arm/dts/Makefile | 2 +
arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 ++++
arch/arm/dts/sun8i-a83t.dtsi | 247 ++++++++++++
arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++
arch/arm/include/asm/arch-sunxi/dram.h | 2 +
arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++
arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
board/sunxi/Kconfig | 12 +-
board/sunxi/MAINTAINERS | 5 +
board/sunxi/board.c | 8 +
configs/h8_homlet_v2_defconfig | 26 ++
drivers/power/Kconfig | 34 +-
drivers/power/Makefile | 1 +
drivers/power/axp818.c | 132 +++++++
include/axp818.h | 75 ++++
include/axp_pmic.h | 3 +
include/configs/sun8i.h | 2 +
include/configs/sunxi-common.h | 2 +-
25 files changed, 1698 insertions(+), 16 deletions(-)
create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
create mode 100644 arch/arm/dts/sun8i-a83t.dtsi
create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
create mode 100644 configs/h8_homlet_v2_defconfig
create mode 100644 drivers/power/axp818.c
create mode 100644 include/axp818.h
--
1.9.1
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for A83T SOC
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:19 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 02/10] sunxi: Add support for UART0 in PB pin group on A83T Vishnu Patekar
` (9 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 ++
board/sunxi/Kconfig | 11 ++++++++++-
include/configs/sun8i.h | 2 ++
3 files changed, 14 insertions(+), 1 deletion(-)
diff --git a/arch/arm/cpu/armv7/sunxi/cpu_info.c b/arch/arm/cpu/armv7/sunxi/cpu_info.c
index 05fef32..c9b4bc0 100644
--- a/arch/arm/cpu/armv7/sunxi/cpu_info.c
+++ b/arch/arm/cpu/armv7/sunxi/cpu_info.c
@@ -71,6 +71,8 @@ int print_cpuinfo(void)
puts("CPU: Allwinner A33 (SUN8I)\n");
#elif defined CONFIG_MACH_SUN9I
puts("CPU: Allwinner A80 (SUN9I)\n");
+#elif defined CONFIG_MACH_SUN8I_A83T
+ puts("CPU: Allwinner A83T (SUN8I)\n");
#else
#warning Please update cpu_info.c with correct CPU information
puts("CPU: SUNXI Family\n");
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index f6f2a60..ea69bf7 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -68,6 +68,15 @@ config MACH_SUN8I_A33
select SUPPORT_SPL
select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+config MACH_SUN8I_A83T
+ bool "sun8i (Allwinner A83T)"
+ select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SUNXI_GEN_SUN6I
+ select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
config MACH_SUN9I
bool "sun9i (Allwinner A80)"
select CPU_V7
@@ -78,7 +87,7 @@ endchoice
# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
config MACH_SUN8I
bool
- default y if MACH_SUN8I_A23 || MACH_SUN8I_A33
+ default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_A83T
config DRAM_CLK
diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h
index 4fc6365..c139e0a 100644
--- a/include/configs/sun8i.h
+++ b/include/configs/sun8i.h
@@ -25,6 +25,8 @@
#define CONFIG_ARMV7_PSCI_NR_CPUS 2
#elif defined(CONFIG_MACH_SUN8I_A33)
#define CONFIG_ARMV7_PSCI_NR_CPUS 4
+#elif defined(CONFIG_MACH_SUN8I_A83T)
+#define CONFIG_ARMV7_PSCI_NR_CPUS 8
#else
#error Unsupported sun8i variant
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 02/10] sunxi: Add support for UART0 in PB pin group on A83T
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for " Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:19 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver Vishnu Patekar
` (8 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/cpu/armv7/sunxi/board.c | 4 ++++
arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
2 files changed, 5 insertions(+)
diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c
index 4785ac6..348f028 100644
--- a/arch/arm/cpu/armv7/sunxi/board.c
+++ b/arch/arm/cpu/armv7/sunxi/board.c
@@ -72,6 +72,10 @@ static int gpio_init(void)
sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_A33_GPB_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_A33_GPB_UART0);
sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP);
+#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_A83T)
+ sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_A83T_GPB_UART0);
+ sunxi_gpio_set_cfgpin(SUNXI_GPB(10), SUN8I_A83T_GPB_UART0);
+ sunxi_gpio_set_pull(SUNXI_GPB(10), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h
index 8382101..14a3328 100644
--- a/arch/arm/include/asm/arch-sunxi/gpio.h
+++ b/arch/arm/include/asm/arch-sunxi/gpio.h
@@ -157,6 +157,7 @@ enum sunxi_gpio_number {
#define SUN5I_GPB_UART0 2
#define SUN8I_GPB_UART2 2
#define SUN8I_A33_GPB_UART0 3
+#define SUN8I_A83T_GPB_UART0 2
#define SUNXI_GPC_NAND 2
#define SUNXI_GPC_SDC2 3
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for " Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 02/10] sunxi: Add support for UART0 in PB pin group on A83T Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:21 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818 Vishnu Patekar
` (7 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
It's registers are different and calculating reg config is different than
that of earlier axp power ICs.
DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
all other voltages can be added subsequently.
AXP datasheet is uploaded to wiki:
http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
drivers/power/Kconfig | 34 ++++++++-----
drivers/power/Makefile | 1 +
drivers/power/axp818.c | 132 +++++++++++++++++++++++++++++++++++++++++++++++++
include/axp818.h | 75 ++++++++++++++++++++++++++++
include/axp_pmic.h | 3 ++
5 files changed, 234 insertions(+), 11 deletions(-)
create mode 100644 drivers/power/axp818.c
create mode 100644 include/axp818.h
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 809f8f1..d2494d4 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -8,7 +8,8 @@ choice
prompt "Select Sunxi PMIC Variant"
depends on ARCH_SUNXI
default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
- default AXP221_POWER if MACH_SUN6I || MACH_SUN8I
+ default AXP221_POWER if MACH_SUN6I || MACH_SUN8I && !MACH_SUN8I_A83T
+ default AXP818_POWER if MACH_SUN8I_A83T
config SUNXI_NO_PMIC
boolean "board without a pmic"
@@ -31,16 +32,24 @@ config AXP209_POWER
config AXP221_POWER
boolean "axp221 / axp223 pmic support"
- depends on MACH_SUN6I || MACH_SUN8I
+ depends on MACH_SUN6I || MACH_SUN8I || !MACH_SUN8I_A83T
---help---
Select this to enable support for the axp221/axp223 pmic found on most
A23 and A31 boards.
+config AXP818_POWER
+ boolean "axp818 pmic support"
+ depends on MACH_SUN8I_A83T
+ ---help---
+ Say y here to enable support for the axp818 pmic found on
+ A83T dev board.
+
endchoice
config AXP_DCDC1_VOLT
int "axp pmic dcdc1 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
+ default 3300 if AXP818_POWER
default 3000 if MACH_SUN6I || MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
@@ -51,7 +60,8 @@ config AXP_DCDC1_VOLT
config AXP_DCDC2_VOLT
int "axp pmic dcdc2 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
+ default 900 if AXP818_POWER
default 1400 if AXP152_POWER || AXP209_POWER
default 1200 if MACH_SUN6I
default 1100 if MACH_SUN8I
@@ -64,7 +74,8 @@ config AXP_DCDC2_VOLT
config AXP_DCDC3_VOLT
int "axp pmic dcdc3 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
+ default 900 if AXP818_POWER
default 1500 if AXP152_POWER
default 1250 if AXP209_POWER
default 1200 if MACH_SUN6I || MACH_SUN8I
@@ -78,7 +89,7 @@ config AXP_DCDC3_VOLT
config AXP_DCDC4_VOLT
int "axp pmic dcdc4 voltage"
- depends on AXP152_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP221_POWER || AXP818_POWER
default 1250 if AXP152_POWER
default 1200 if MACH_SUN6I
default 0 if MACH_SUN8I
@@ -91,7 +102,8 @@ config AXP_DCDC4_VOLT
config AXP_DCDC5_VOLT
int "axp pmic dcdc5 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
+ default 1800 if AXP818_POWER
default 1500 if MACH_SUN6I || MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
@@ -111,7 +123,7 @@ config AXP_ALDO1_VOLT
config AXP_ALDO2_VOLT
int "axp pmic (a)ldo2 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
default 3000 if AXP152_POWER || AXP209_POWER
default 0 if MACH_SUN6I
default 2500 if MACH_SUN8I
@@ -125,8 +137,8 @@ config AXP_ALDO2_VOLT
config AXP_ALDO3_VOLT
int "axp pmic (a)ldo3 voltage"
- depends on AXP209_POWER || AXP221_POWER
- default 0 if AXP209_POWER
+ depends on AXP209_POWER || AXP221_POWER || AXP818_POWER
+ default 0 if AXP209_POWER || AXP818_POWER
default 3000 if MACH_SUN6I || MACH_SUN8I
---help---
Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
@@ -171,7 +183,7 @@ config AXP_DLDO3_VOLT
config AXP_DLDO4_VOLT
int "axp pmic dldo4 voltage"
- depends on AXP221_POWER
+ depends on AXP221_POWER || AXP818_POWER
default 0
---help---
Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index a2d3c04..0fdbca3 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_AS3722_POWER) += as3722.o
obj-$(CONFIG_AXP152_POWER) += axp152.o
obj-$(CONFIG_AXP209_POWER) += axp209.o
obj-$(CONFIG_AXP221_POWER) += axp221.o
+obj-$(CONFIG_AXP818_POWER) += axp818.o
obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
obj-$(CONFIG_FTPMU010_POWER) += ftpmu010.o
obj-$(CONFIG_TPS6586X_POWER) += tps6586x.o
diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
new file mode 100644
index 0000000..4b21a83
--- /dev/null
+++ b/drivers/power/axp818.c
@@ -0,0 +1,132 @@
+/*
+ * AXP818 driver based on AXP221 driver
+ *
+ *
+ * (C) Copyright 2015 Vishnu Patekar <vishnuptekar0510@gmail.com>
+ *
+ * Based on axp221.c
+ * (C) Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ * (C) Copyright 2013 Oliver Schinagl <oliver@schinagl.nl>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/pmic_bus.h>
+#include <axp_pmic.h>
+
+static u8 axp818_mvolt_to_cfg(int mvolt, int min, int max, int div)
+{
+ if (mvolt < min)
+ mvolt = min;
+ else if (mvolt > max)
+ mvolt = max;
+
+ return (mvolt - min) / div;
+}
+
+int axp_set_dcdc1(unsigned int mvolt)
+{
+ int ret;
+ u8 cfg = axp818_mvolt_to_cfg(mvolt, 1600, 3400, 100);
+
+ if (mvolt == 0)
+ return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC1_EN);
+
+ ret = pmic_bus_write(AXP818_DCDC1_CTRL, cfg);
+ if (ret)
+ return ret;
+
+ return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC1_EN);
+}
+
+int axp_set_dcdc2(unsigned int mvolt)
+{
+ int ret;
+ u8 cfg;
+
+ if (mvolt >= 1220)
+ cfg = 70 + axp818_mvolt_to_cfg(mvolt, 1220, 1300, 20);
+ else
+ cfg = axp818_mvolt_to_cfg(mvolt, 500, 1200, 10);
+
+ if (mvolt == 0)
+ return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC2_EN);
+
+ ret = pmic_bus_write(AXP818_DCDC2_CTRL, cfg);
+ if (ret)
+ return ret;
+
+ return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC2_EN);
+}
+
+int axp_set_dcdc3(unsigned int mvolt)
+{
+ int ret;
+ u8 cfg;
+
+ if (mvolt >= 1220)
+ cfg = 70 + axp818_mvolt_to_cfg(mvolt, 1220, 1300, 20);
+ else
+ cfg = axp818_mvolt_to_cfg(mvolt, 500, 1200, 10);
+
+ if (mvolt == 0)
+ return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC3_EN);
+
+ ret = pmic_bus_write(AXP818_DCDC3_CTRL, cfg);
+ if (ret)
+ return ret;
+
+ return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC3_EN);
+}
+
+int axp_set_dcdc5(unsigned int mvolt)
+{
+ int ret;
+ u8 cfg;
+
+ if (mvolt >= 1140)
+ cfg = 32 + axp818_mvolt_to_cfg(mvolt, 1140, 1840, 20);
+ else
+ cfg = axp818_mvolt_to_cfg(mvolt, 800, 1120, 10);
+
+ if (mvolt == 0)
+ return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC5_EN);
+
+ ret = pmic_bus_write(AXP818_DCDC5_CTRL, cfg);
+ if (ret)
+ return ret;
+
+ return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
+ AXP818_OUTPUT_CTRL1_DCDC5_EN);
+}
+
+int axp_init(void)
+{
+ u8 axp_chip_id;
+ int ret;
+
+ ret = pmic_bus_init();
+ if (ret)
+ return ret;
+
+ ret = pmic_bus_read(AXP818_CHIP_ID, &axp_chip_id);
+ if (ret)
+ return ret;
+
+ if (!(axp_chip_id == 0x51))
+ return -ENODEV;
+ else
+ return ret;
+
+ return 0;
+}
diff --git a/include/axp818.h b/include/axp818.h
new file mode 100644
index 0000000..1dc6456
--- /dev/null
+++ b/include/axp818.h
@@ -0,0 +1,75 @@
+/*
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ *
+ * X-Powers AXP818 Power Management IC driver
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#define AXP818_CHIP_ID 0x03
+
+#define AXP818_OUTPUT_CTRL1 0x10
+#define AXP818_OUTPUT_CTRL1_DCDC1_EN (1 << 0)
+#define AXP818_OUTPUT_CTRL1_DCDC2_EN (1 << 1)
+#define AXP818_OUTPUT_CTRL1_DCDC3_EN (1 << 2)
+#define AXP818_OUTPUT_CTRL1_DCDC4_EN (1 << 3)
+#define AXP818_OUTPUT_CTRL1_DCDC5_EN (1 << 4)
+#define AXP818_OUTPUT_CTRL1_DCDC6_EN (1 << 5)
+#define AXP818_OUTPUT_CTRL1_DCDC7_EN (1 << 6)
+#define AXP818_OUTPUT_CTRL2 0x12
+#define AXP818_OUTPUT_CTRL2_ELDO1_EN (1 << 0)
+#define AXP818_OUTPUT_CTRL2_ELDO2_EN (1 << 1)
+#define AXP818_OUTPUT_CTRL2_ELDO3_EN (1 << 2)
+#define AXP818_OUTPUT_CTRL2_DLDO1_EN (1 << 3)
+#define AXP818_OUTPUT_CTRL2_DLDO2_EN (1 << 4)
+#define AXP818_OUTPUT_CTRL2_DLDO3_EN (1 << 5)
+#define AXP818_OUTPUT_CTRL2_DLDO4_EN (1 << 6)
+#define AXP818_OUTPUT_CTRL3 0x13
+#define AXP818_OUTPUT_CTRL3_FLDO1_EN (1 << 2)
+#define AXP818_OUTPUT_CTRL3_FLDO2_EN (1 << 3)
+#define AXP818_OUTPUT_CTRL3_FLDO3_EN (1 << 4)
+#define AXP818_OUTPUT_CTRL3_ALDO1_EN (1 << 5)
+#define AXP818_OUTPUT_CTRL3_ALDO2_EN (1 << 6)
+#define AXP818_OUTPUT_CTRL3_ALDO3_EN (1 << 7)
+
+#define AXP818_DCDC1_CTRL 0x20
+#define AXP818_DCDC2_CTRL 0x21
+#define AXP818_DCDC3_CTRL 0x22
+#define AXP818_DCDC4_CTRL 0x23
+#define AXP818_DCDC5_CTRL 0x24
+#define AXP818_DCDC6_CTRL 0x25
+
+#define AXP818_DLDO1_CTRL 0x15
+#define AXP818_DLDO2_CTRL 0x16
+#define AXP818_DLDO3_CTRL 0x17
+#define AXP818_DLDO4_CTRL 0x18
+#define AXP818_ELDO1_CTRL 0x19
+#define AXP818_ELDO2_CTRL 0x1a
+#define AXP818_ELDO3_CTRL 0x1b
+#define AXP818_ELDO3_CTRL 0x1b
+#define AXP818_FLDO1_CTRL 0x1c
+#define AXP818_FLDO2_3_CTRL 0x1d
+#define AXP818_DCDC1_CTRL 0x20
+#define AXP818_DCDC2_CTRL 0x21
+#define AXP818_DCDC3_CTRL 0x22
+#define AXP818_DCDC4_CTRL 0x23
+#define AXP818_DCDC5_CTRL 0x24
+#define AXP818_DCDC6_CTRL 0x25
+#define AXP818_DCDC7_CTRL 0x26
+
+#define AXP818_ALDO1_CTRL 0x28
+#define AXP818_ALDO2_CTRL 0x29
+#define AXP818_ALDO3_CTRL 0x2a
+
+int axp818_init(void);
+
+/* For axp_gpio.c */
+#define AXP_POWER_STATUS 0x00
+#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x92
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x94
+#define AXP_GPIO_STATE_OFFSET 0
diff --git a/include/axp_pmic.h b/include/axp_pmic.h
index ef339c4..3b01c49 100644
--- a/include/axp_pmic.h
+++ b/include/axp_pmic.h
@@ -16,6 +16,9 @@
#ifdef CONFIG_AXP221_POWER
#include <axp221.h>
#endif
+#ifdef CONFIG_AXP818_POWER
+#include <axp818.h>
+#endif
int axp_set_dcdc1(unsigned int mvolt);
int axp_set_dcdc2(unsigned int mvolt);
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (2 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:24 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 05/10] sunxi: do not enable smp for A83T Vishnu Patekar
` (6 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/cpu/armv7/sunxi/Makefile | 1 +
arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +++++++++++++++
board/sunxi/board.c | 8 ++++++++
include/configs/sunxi-common.h | 2 +-
4 files changed, 25 insertions(+), 1 deletion(-)
diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
index 459d5d8..929a933 100644
--- a/arch/arm/cpu/armv7/sunxi/Makefile
+++ b/arch/arm/cpu/armv7/sunxi/Makefile
@@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_SUN6I) += tzpc.o
obj-$(CONFIG_AXP152_POWER) += pmic_bus.o
obj-$(CONFIG_AXP209_POWER) += pmic_bus.o
obj-$(CONFIG_AXP221_POWER) += pmic_bus.o
+obj-$(CONFIG_AXP818_POWER) += pmic_bus.o
ifndef CONFIG_SPL_BUILD
ifdef CONFIG_ARMV7_PSCI
diff --git a/arch/arm/cpu/armv7/sunxi/pmic_bus.c b/arch/arm/cpu/armv7/sunxi/pmic_bus.c
index 9e05127..838831d 100644
--- a/arch/arm/cpu/armv7/sunxi/pmic_bus.c
+++ b/arch/arm/cpu/armv7/sunxi/pmic_bus.c
@@ -26,6 +26,9 @@
#define AXP223_DEVICE_ADDR 0x3a3
#define AXP223_RUNTIME_ADDR 0x2d
+#define AXP818_DEVICE_ADDR 0x3a3
+#define AXP818_RUNTIME_ADDR 0x2d
+
int pmic_bus_init(void)
{
/* This cannot be 0 because it is used in SPL before BSS is ready */
@@ -49,6 +52,14 @@ int pmic_bus_init(void)
# endif
if (ret)
return ret;
+#elif defined CONFIG_AXP818_POWER
+ ret = rsb_init();
+ if (ret)
+ return ret;
+
+ ret = rsb_set_device_address(AXP818_DEVICE_ADDR, AXP818_RUNTIME_ADDR);
+ if (ret)
+ return ret;
#endif
needs_init = 0;
@@ -67,6 +78,8 @@ int pmic_bus_read(u8 reg, u8 *data)
# else
return rsb_read(AXP223_RUNTIME_ADDR, reg, data);
# endif
+#elif defined CONFIG_AXP818_POWER
+ return rsb_read(AXP818_RUNTIME_ADDR, reg, data);
#endif
}
@@ -82,6 +95,8 @@ int pmic_bus_write(u8 reg, u8 data)
# else
return rsb_write(AXP223_RUNTIME_ADDR, reg, data);
# endif
+#elif CONFIG_AXP818_POWER
+ return rsb_write(AXP818_RUNTIME_ADDR, reg, data);
#endif
}
diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index 6ac398c..ebfa94e 100644
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -430,6 +430,14 @@ void sunxi_board_init(void)
int power_failed = 0;
unsigned long ramsize;
+#if defined CONFIG_AXP818_POWER
+ power_failed = axp_init();
+ power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+ power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
+ power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
+ power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
+#endif
+
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER
power_failed = axp_init();
diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index ddcfe94..61af897 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -243,7 +243,7 @@ extern int soft_i2c_gpio_scl;
#endif
/* PMU */
-#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER
+#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
#define CONFIG_SPL_POWER_SUPPORT
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 05/10] sunxi: do not enable smp for A83T
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (3 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818 Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:24 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks " Vishnu Patekar
` (5 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
When smp is enabled for A83T, intermittent hang is observed after booting kernel.
for now do not enable the smp for CPU0. This has to be fixed.
Also, fixed the space at line start warning at these two lines.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/cpu/armv7/sunxi/board.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c
index 348f028..e463e5b 100644
--- a/arch/arm/cpu/armv7/sunxi/board.c
+++ b/arch/arm/cpu/armv7/sunxi/board.c
@@ -113,8 +113,8 @@ void s_init(void)
setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
#endif
#if defined CONFIG_MACH_SUN6I || \
- defined CONFIG_MACH_SUN7I || \
- defined CONFIG_MACH_SUN8I
+ defined CONFIG_MACH_SUN7I || \
+ defined CONFIG_MACH_SUN8I && !(CONFIG_MACH_SUN8I_A83T)
/* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
asm volatile(
"mrc p15, 0, r0, c1, c0, 1\n"
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks for A83T
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (4 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 05/10] sunxi: do not enable smp for A83T Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:25 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 07/10] sunxi: Add support for Allwinner A83T DRAM Vishnu Patekar
` (4 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/cpu/armv7/sunxi/Makefile | 4 +
arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++++
arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++++++++
4 files changed, 444 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
index 929a933..3c9fed3 100644
--- a/arch/arm/cpu/armv7/sunxi/Makefile
+++ b/arch/arm/cpu/armv7/sunxi/Makefile
@@ -26,7 +26,11 @@ obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o
obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o
obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o
obj-$(CONFIG_MACH_SUN7I) += clock_sun4i.o
+ifdef CONFIG_MACH_SUN8I_A83T
+obj-y += clock_sun8i_a83t.o
+else
obj-$(CONFIG_MACH_SUN8I) += clock_sun6i.o
+endif
obj-$(CONFIG_MACH_SUN9I) += clock_sun9i.o
obj-$(CONFIG_MACH_SUN6I) += tzpc.o
diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c b/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
new file mode 100644
index 0000000..76efa93
--- /dev/null
+++ b/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
@@ -0,0 +1,133 @@
+/*
+ * sun6i specific clock code
+ *
+ * (C) Copyright 2007-2012
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ * Tom Cubie <tangliang@allwinnertech.com>
+ *
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/prcm.h>
+#include <asm/arch/sys_proto.h>
+
+#ifdef CONFIG_SPL_BUILD
+void clock_init_safe(void)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ clock_set_pll1(408000000);
+ /* enable pll_hsic, default is 480M */
+ writel(PLL8_CFG_DEFAULT, &ccm->pll8_cfg);
+ writel(readl(&ccm->pll8_cfg) | (0x1 << 31), &ccm->pll8_cfg);
+
+ /* switch to default 24MHz before changing to hsic */
+ writel(0x0, &ccm->cci400_cfg);
+ sdelay(50);
+ writel(CCM_CCI400_CLK_SEL_HSIC, &ccm->cci400_cfg);
+ sdelay(100);
+
+ /* switch before changing pll6 */
+ clrsetbits_le32(&ccm->ahb1_apb1_div, AHB1_CLK_SRC_MASK,
+ AHB1_CLK_SRC_OSC24M);
+ writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg);
+ sdelay(100);
+
+ writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
+ writel(CCM_MBUS_RESET_RESET, &ccm->mbus_reset);
+ writel(MBUS_CLK_DEFAULT, &ccm->mbus_clk_cfg);
+
+ /* timestamp */
+ writel(1, 0x01720000);
+}
+#endif
+
+void clock_init_uart(void)
+{
+ struct sunxi_ccm_reg *const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ /* uart clock source is apb2 */
+ writel(APB2_CLK_SRC_OSC24M|
+ APB2_CLK_RATE_N_1|
+ APB2_CLK_RATE_M(1),
+ &ccm->apb2_div);
+
+ /* open the clock for uart */
+ setbits_le32(&ccm->apb2_gate,
+ CLK_GATE_OPEN << (APB2_GATE_UART_SHIFT +
+ CONFIG_CONS_INDEX - 1));
+
+ /* deassert uart reset */
+ setbits_le32(&ccm->apb2_reset_cfg,
+ 1 << (APB2_RESET_UART_SHIFT +
+ CONFIG_CONS_INDEX - 1));
+}
+
+#ifdef CONFIG_SPL_BUILD
+void clock_set_pll1(unsigned int clk)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ const int p = 0;
+
+ /* Switch to 24MHz clock while changing PLL1 */
+ writel(AXI_DIV_2 << AXI0_DIV_SHIFT |
+ CPU_CLK_SRC_OSC24M << C0_CPUX_CLK_SRC_SHIFT,
+ &ccm->cpu_axi_cfg);
+
+ /* clk = 24*n/p, p is ignored if clock is >288MHz */
+ writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) | CMM_PLL1_CLOCK_TIME_2 |
+ CCM_PLL1_CTRL_N(clk / 24000000),
+ &ccm->pll1_c0_cfg);
+ sdelay(200);
+
+ writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) | CMM_PLL1_CLOCK_TIME_2 |
+ CCM_PLL1_CTRL_N(clk / (24000000)),
+ &ccm->pll1_c1_cfg);
+ sdelay(200);
+
+ /* Switch CPU to PLL1 */
+ writel(AXI_DIV_2 << AXI0_DIV_SHIFT |
+ AXI_DIV_2 << AXI1_DIV_SHIFT |
+ CPU_CLK_SRC_PLL1 << C0_CPUX_CLK_SRC_SHIFT |
+ CPU_CLK_SRC_PLL1 << C1_CPUX_CLK_SRC_SHIFT,
+ &ccm->cpu_axi_cfg);
+}
+#endif
+
+void clock_set_pll5(unsigned int clk)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ unsigned int div1 = 0, div2 = 0;
+
+ /* A83T PLL5 DDR rate = 24000000 * (n+1)/(div1+1)/(div2+1) */
+ writel(CCM_PLL5_CTRL_EN | CCM_PLL5_CTRL_UPD |
+ CCM_PLL5_CTRL_N(clk / (24000000)) |
+ div2 << CCM_PLL5_DIV2_SHIFT |
+ div1 << CCM_PLL5_DIV1_SHIFT, &ccm->pll5_cfg);
+
+ udelay(5500);
+}
+
+
+unsigned int clock_get_pll6(void)
+{
+ struct sunxi_ccm_reg *const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ uint32_t rval = readl(&ccm->pll6_cfg);
+ int n = ((rval & CCM_PLL6_CTRL_N_MASK) >> CCM_PLL6_CTRL_N_SHIFT) + 1;
+ int div1 = ((rval & CCM_PLL6_CTRL_DIV1_MASK) >>
+ CCM_PLL6_CTRL_DIV1_SHIFT) + 1;
+ int div2 = ((rval & CCM_PLL6_CTRL_DIV2_MASK) >>
+ CCM_PLL6_CTRL_DIV2_SHIFT) + 1;
+ return 24000000 * n / div1 / div2;
+}
diff --git a/arch/arm/include/asm/arch-sunxi/clock.h b/arch/arm/include/asm/arch-sunxi/clock.h
index 3e5d999..8ca58ae 100644
--- a/arch/arm/include/asm/arch-sunxi/clock.h
+++ b/arch/arm/include/asm/arch-sunxi/clock.h
@@ -15,7 +15,9 @@
#define CLK_GATE_CLOSE 0x0
/* clock control module regs definition */
-#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I)
+#if defined(CONFIG_MACH_SUN8I_A83T)
+#include <asm/arch/clock_sun8i_a83t.h>
+#elif defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I)
#include <asm/arch/clock_sun6i.h>
#elif defined(CONFIG_MACH_SUN9I)
#include <asm/arch/clock_sun9i.h>
diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h b/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
new file mode 100644
index 0000000..28ea16c
--- /dev/null
+++ b/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
@@ -0,0 +1,304 @@
+/*
+ * sun8i a83t clock register definitions
+ *
+ * (C) Copyright 2007-2011
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ * Tom Cubie <tangliang@allwinnertech.com>
+ *
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * from sun6i.h
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SUNXI_CLOCK_SUN8I_A83T_H
+#define _SUNXI_CLOCK_SUN8I_A83T_H
+
+struct sunxi_ccm_reg {
+ u32 pll1_c0_cfg; /* 0x00 c1cpu# pll control */
+ u32 pll1_c1_cfg; /* 0x04 c1cpu# pll control */
+ u32 pll2_cfg; /* 0x08 pll2 audio control */
+ u32 reserved1;
+ u32 pll3_cfg; /* 0x10 pll3 video0 control */
+ u32 reserved2;
+ u32 pll4_cfg; /* 0x18 pll4 ve control */
+ u32 reserved3;
+ u32 pll5_cfg; /* 0x20 pll5 ddr control */
+ u32 reserved4;
+ u32 pll6_cfg; /* 0x28 pll6 peripheral control */
+ u32 reserved5[3]; /* 0x2c */
+ u32 pll7_cfg; /* 0x38 pll7 gpu control */
+ u32 reserved6[2]; /* 3c */
+ u32 pll8_cfg; /* 0x44 pll8 hsic control */
+ u32 pll9_cfg; /* 0x48 pll9 de control */
+ u32 pll10_cfg; /* 0x4c pll10 video1 control */
+ u32 cpu_axi_cfg; /* 0x50 CPU/AXI divide ratio */
+ u32 ahb1_apb1_div; /* 0x54 AHB1/APB1 divide ratio */
+ u32 apb2_div; /* 0x58 APB2 divide ratio */
+ u32 ahb2_div; /* 0x5c AHB2 divide ratio */
+ u32 ahb_gate0; /* 0x60 ahb module clock gating 0 */
+ u32 ahb_gate1; /* 0x64 ahb module clock gating 1 */
+ u32 apb1_gate; /* 0x68 apb1 module clock gating 3 */
+ u32 apb2_gate; /* 0x6c apb2 module clock gating 4 */
+ u32 reserved7[2]; /* 0x70 */
+ u32 cci400_cfg; /* 0x78 cci400 clock configuration A83T only */
+ u32 reserved8; /* 0x7c */
+ u32 nand0_clk_cfg; /* 0x80 nand clock control */
+ u32 reserved9; /* 0x84 */
+ u32 sd0_clk_cfg; /* 0x88 sd0 clock control */
+ u32 sd1_clk_cfg; /* 0x8c sd1 clock control */
+ u32 sd2_clk_cfg; /* 0x90 sd2 clock control */
+ u32 sd3_clk_cfg; /* 0x94 sd3 clock control */
+ u32 reserved10; /* 0x98 */
+ u32 ss_clk_cfg; /* 0x9c security system clock control */
+ u32 spi0_clk_cfg; /* 0xa0 spi0 clock control */
+ u32 spi1_clk_cfg; /* 0xa4 spi1 clock control */
+ u32 reserved11[2]; /* 0xa8 */
+ u32 i2s0_clk_cfg; /* 0xb0 I2S0 clock control */
+ u32 i2s1_clk_cfg; /* 0xb4 I2S1 clock control */
+ u32 i2s2_clk_cfg; /* 0xb8 I2S2 clock control */
+ u32 tdm_clk_cfg; /* 0xbc TDM clock control */
+ u32 spdif_clk_cfg; /* 0xc0 SPDIF clock control */
+ u32 reserved12[2]; /* c4 */
+ u32 usb_clk_cfg; /* 0xcc USB clock control */
+ u32 reserved13[9]; /* d0 */
+ u32 dram_clk_cfg; /* 0xf4 DRAM configuration clock control */
+ u32 dram_pll_cfg; /* 0xf8 PLL_DDR cfg register */
+ u32 mbus_reset; /* 0xfc MBUS reset control */
+ u32 dram_clk_gate; /* 0x100 DRAM module gating */
+ u32 reserved14[5]; /* 0x104 BE0 */
+ u32 lcd0_clk_cfg; /* 0x118 LCD0 module clock */
+ u32 lcd1_clk_cfg; /* 0x11c LCD1 module clock */
+ u32 reserved15[4]; /* 0x120 */
+ u32 mipi_csi_clk_cfg; /* 0x130 MIPI CSI module clock */
+ u32 csi_clk_cfg; /* 0x134 CSI module clock */
+ u32 reserved16; /* 0x138 */
+ u32 ve_clk_cfg; /* 0x13c VE module clock */
+ u32 reserved17; /* 0x140 */
+ u32 avs_clk_cfg; /* 0x144 AVS module clock */
+ u32 reserved18[2]; /* 0x148 */
+ u32 hdmi_clk_cfg; /* 0x150 HDMI module clock */
+ u32 hdmi_slow_clk_cfg; /* 0x154 HDMI slow module clock */
+ u32 reserved19; /* 0x158 */
+ u32 mbus_clk_cfg; /* 0x15c MBUS module clock */
+ u32 reserved20[2];
+ u32 mipi_dsi_clk_cfg; /* 0x168 MIPI DSI clock control */
+ u32 reserved21[13]; /* 0x16c */
+ u32 gpu_core_clk_cfg; /* 0x1a0 GPU core clock config */
+ u32 gpu_mem_clk_cfg; /* 0x1a4 GPU memory clock config */
+ u32 gpu_hyd_clk_cfg; /* 0x1a8 GPU HYD clock config */
+ u32 reserved22[21]; /* 0x1ac */
+ u32 pll_stable0; /* 0x200 PLL stable time 0 */
+ u32 pll_stable1; /* 0x204 PLL stable time 1 */
+ u32 reserved23; /* 0x208 */
+ u32 pll_stable_status; /* 0x20c PLL stable status register */
+ u32 reserved24[0x04]; /* 0x210 */
+ u32 pll1_c0_bias_cfg; /* 0x220 PLL1 c0cpu# Bias config */
+ u32 pll2_bias_cfg; /* 0x224 PLL2 audio Bias config */
+ u32 pll3_bias_cfg; /* 0x228 PLL3 video Bias config */
+ u32 pll4_bias_cfg; /* 0x22c PLL4 ve Bias config */
+ u32 pll5_bias_cfg; /* 0x230 PLL5 ddr Bias config */
+ u32 pll6_bias_cfg; /* 0x234 PLL6 periph Bias config */
+ u32 pll1_c1_bias_cfg; /* 0x238 PLL1 c1cpu# Bias config */
+ u32 pll8_bias_cfg; /* 0x23c PLL7 Bias config */
+ u32 reserved25; /* 0x240 */
+ u32 pll9_bias_cfg; /* 0x244 PLL9 hsic Bias config */
+ u32 de_bias_cfg; /* 0x248 display engine Bias config */
+ u32 video1_bias_cfg; /* 0x24c pll video1 bias register */
+ u32 c0_tuning_cfg; /* 0x250 pll c0cpu# tuning register */
+ u32 c1_tuning_cfg; /* 0x254 pll c1cpu# tuning register */
+ u32 reserved26[11]; /* 0x258 */
+ u32 pll2_pattern_cfg0; /* 0x284 PLL2 Pattern register 0 */
+ u32 pll3_pattern_cfg0; /* 0x288 PLL3 Pattern register 0 */
+ u32 reserved27; /* 0x28c */
+ u32 pll5_pattern_cfg0; /* 0x290 PLL5 Pattern register 0*/
+ u32 reserved28[4]; /* 0x294 */
+ u32 pll2_pattern_cfg1; /* 0x2a4 PLL2 Pattern register 1 */
+ u32 pll3_pattern_cfg1; /* 0x2a8 PLL3 Pattern register 1 */
+ u32 reserved29; /* 0x2ac */
+ u32 pll5_pattern_cfg1; /* 0x2b0 PLL5 Pattern register 1 */
+ u32 reserved30[3]; /* 0x2b4 */
+ u32 ahb_reset0_cfg; /* 0x2c0 AHB1 Reset 0 config */
+ u32 ahb_reset1_cfg; /* 0x2c4 AHB1 Reset 1 config */
+ u32 ahb_reset2_cfg; /* 0x2c8 AHB1 Reset 2 config */
+ u32 reserved31;
+ u32 ahb_reset3_cfg; /* 0x2d0 AHB1 Reset 3 config */
+ u32 reserved32; /* 0x2d4 */
+ u32 apb2_reset_cfg; /* 0x2d8 BUS Reset 4 config */
+};
+
+/* apb2 bit field */
+#define APB2_CLK_SRC_LOSC (0x0 << 24)
+#define APB2_CLK_SRC_OSC24M (0x1 << 24)
+#define APB2_CLK_SRC_PLL6 (0x2 << 24)
+#define APB2_CLK_SRC_MASK (0x3 << 24)
+#define APB2_CLK_RATE_N_1 (0x0 << 16)
+#define APB2_CLK_RATE_N_2 (0x1 << 16)
+#define APB2_CLK_RATE_N_4 (0x2 << 16)
+#define APB2_CLK_RATE_N_8 (0x3 << 16)
+#define APB2_CLK_RATE_N_MASK (3 << 16)
+#define APB2_CLK_RATE_M(m) (((m)-1) << 0)
+#define APB2_CLK_RATE_M_MASK (0x1f << 0)
+
+/* apb2 gate field */
+#define APB2_GATE_UART_SHIFT (16)
+#define APB2_GATE_UART_MASK (0xff << APB2_GATE_UART_SHIFT)
+#define APB2_GATE_TWI_SHIFT (0)
+#define APB2_GATE_TWI_MASK (0xf << APB2_GATE_TWI_SHIFT)
+
+/* cpu_axi_cfg bits */
+#define AXI0_DIV_SHIFT 0
+#define AXI1_DIV_SHIFT 16
+#define C0_CPUX_CLK_SRC_SHIFT 12
+#define C1_CPUX_CLK_SRC_SHIFT 28
+
+#define AXI_DIV_1 0
+#define AXI_DIV_2 1
+#define AXI_DIV_3 2
+#define AXI_DIV_4 3
+#define CPU_CLK_SRC_OSC24M 0
+#define CPU_CLK_SRC_PLL1 1
+
+#define CCM_PLL1_CTRL_N(n) ((((n) - 1) & 0xff) << 8)
+#define CCM_PLL1_CTRL_P(n) (((n) & 0x1) << 16)
+#define CCM_PLL1_CTRL_EN (0x1 << 31)
+#define CMM_PLL1_CLOCK_TIME_2 (0x2 << 24)
+
+#define PLL8_CFG_DEFAULT 0x42800
+#define CCM_CCI400_CLK_SEL_HSIC (0x2<<24)
+
+#define CCM_PLL5_DIV1_SHIFT 16
+#define CCM_PLL5_DIV2_SHIFT 18
+#define CCM_PLL5_CTRL_N(n) (((n) - 1) << 8)
+#define CCM_PLL5_CTRL_UPD (0x1 << 30)
+#define CCM_PLL5_CTRL_EN (0x1 << 31)
+
+#define PLL6_CFG_DEFAULT 0x80041800 /* 576 MHz */
+#define CCM_PLL6_CTRL_N_SHIFT 8
+#define CCM_PLL6_CTRL_N_MASK (0xff << CCM_PLL6_CTRL_N_SHIFT)
+#define CCM_PLL6_CTRL_DIV1_SHIFT 16
+#define CCM_PLL6_CTRL_DIV1_MASK (0x1 << CCM_PLL6_CTRL_DIV1_SHIFT)
+#define CCM_PLL6_CTRL_DIV2_SHIFT 18
+#define CCM_PLL6_CTRL_DIV2_MASK (0x1 << CCM_PLL6_CTRL_DIV2_SHIFT)
+
+#define AHB1_ABP1_DIV_DEFAULT 0x00002190
+#define AHB1_CLK_SRC_MASK (0x3<<12)
+#define AHB1_CLK_SRC_INTOSC (0x0<<12)
+#define AHB1_CLK_SRC_OSC24M (0x1<<12)
+#define AHB1_CLK_SRC_PLL6 (0x2<<12)
+
+#define AXI_GATE_OFFSET_DRAM 0
+
+/* ahb_gate0 offsets */
+#define AHB_GATE_OFFSET_USB_OHCI1 30
+#define AHB_GATE_OFFSET_USB_OHCI0 29
+#define AHB_GATE_OFFSET_USB_EHCI1 27
+#define AHB_GATE_OFFSET_USB_EHCI0 26
+#define AHB_GATE_OFFSET_USB0 24
+#define AHB_GATE_OFFSET_SPI1 21
+#define AHB_GATE_OFFSET_SPI0 20
+#define AHB_GATE_OFFSET_HSTIMER 19
+#define AHB_GATE_OFFSET_EMAC 17
+#define AHB_GATE_OFFSET_MCTL 14
+#define AHB_GATE_OFFSET_GMAC 17
+#define AHB_GATE_OFFSET_NAND0 13
+#define AHB_GATE_OFFSET_MMC0 8
+#define AHB_GATE_OFFSET_MMC(n) (AHB_GATE_OFFSET_MMC0 + (n))
+#define AHB_GATE_OFFSET_DMA 6
+#define AHB_GATE_OFFSET_SS 5
+
+/* ahb_gate1 offsets */
+#define AHB_GATE_OFFSET_DRC0 25
+#define AHB_GATE_OFFSET_DE_FE0 14
+#define AHB_GATE_OFFSET_DE_BE0 12
+#define AHB_GATE_OFFSET_HDMI 11
+#define AHB_GATE_OFFSET_LCD1 5
+#define AHB_GATE_OFFSET_LCD0 4
+
+#define CCM_MMC_CTRL_M(x) ((x) - 1)
+#define CCM_MMC_CTRL_OCLK_DLY(x) ((x) << 8)
+#define CCM_MMC_CTRL_N(x) ((x) << 16)
+#define CCM_MMC_CTRL_SCLK_DLY(x) ((x) << 20)
+#define CCM_MMC_CTRL_OSCM24 (0x0 << 24)
+#define CCM_MMC_CTRL_PLL6 (0x1 << 24)
+#define CCM_MMC_CTRL_ENABLE (0x1 << 31)
+
+#define CCM_USB_CTRL_PHY0_RST (0x1 << 0)
+#define CCM_USB_CTRL_PHY1_RST (0x1 << 1)
+#define CCM_USB_CTRL_PHY2_RST (0x1 << 2)
+/* There is no global phy clk gate on sun6i, define as 0 */
+#define CCM_USB_CTRL_PHYGATE 0
+#define CCM_USB_CTRL_PHY0_CLK (0x1 << 8)
+#define CCM_USB_CTRL_PHY1_CLK (0x1 << 9)
+#define CCM_USB_CTRL_PHY2_CLK (0x1 << 10)
+#define CCM_USB_CTRL_OHCI0_CLK (0x1 << 16)
+#define CCM_USB_CTRL_OHCI1_CLK (0x1 << 17)
+
+#define CCM_GMAC_CTRL_TX_CLK_SRC_MII 0x0
+#define CCM_GMAC_CTRL_TX_CLK_SRC_EXT_RGMII 0x1
+#define CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII 0x2
+#define CCM_GMAC_CTRL_GPIT_MII (0x0 << 2)
+#define CCM_GMAC_CTRL_GPIT_RGMII (0x1 << 2)
+#define CCM_GMAC_CTRL_RX_CLK_DELAY(x) ((x) << 5)
+#define CCM_GMAC_CTRL_TX_CLK_DELAY(x) ((x) << 10)
+
+#define MDFS_CLK_DEFAULT 0x81000002 /* PLL6 / 3 */
+
+#define CCM_DRAMCLK_CFG_DIV(x) ((x - 1) << 0)
+#define CCM_DRAMCLK_CFG_DIV_MASK (0xf << 0)
+#define CCM_DRAMCLK_CFG_DIV0(x) ((x - 1) << 8)
+#define CCM_DRAMCLK_CFG_DIV0_MASK (0xf << 8)
+#define CCM_DRAMCLK_CFG_UPD (0x1 << 16)
+#define CCM_DRAMCLK_CFG_RST (0x1 << 31)
+
+#define CCM_DRAMPLL_CFG_SRC_PLL5 (0x0 << 16) /* Select PLL5 (DDR0) */
+#define CCM_DRAMPLL_CFG_SRC_PLL11 (0x1 << 16) /* Select PLL11 (DDR1) */
+#define CCM_DRAMPLL_CFG_SRC_MASK (0x1 << 16)
+
+#define CCM_MBUS_RESET_RESET (0x1 << 31)
+
+#define CCM_DRAM_GATE_OFFSET_DE_FE0 24
+#define CCM_DRAM_GATE_OFFSET_DE_FE1 25
+#define CCM_DRAM_GATE_OFFSET_DE_BE0 26
+#define CCM_DRAM_GATE_OFFSET_DE_BE1 27
+
+
+#define MBUS_CLK_DEFAULT 0x81000002 /* PLL6 / 2 */
+
+#define MBUS_CLK_GATE (0x1 << 31)
+
+/* ahb_reset0 offsets */
+#define AHB_RESET_OFFSET_GMAC 17
+#define AHB_RESET_OFFSET_MCTL 14
+#define AHB_RESET_OFFSET_MMC3 11
+#define AHB_RESET_OFFSET_MMC2 10
+#define AHB_RESET_OFFSET_MMC1 9
+#define AHB_RESET_OFFSET_MMC0 8
+#define AHB_RESET_OFFSET_MMC(n) (AHB_RESET_OFFSET_MMC0 + (n))
+#define AHB_RESET_OFFSET_SS 5
+
+/* ahb_reset1 offsets */
+#define AHB_RESET_OFFSET_SAT 26
+#define AHB_RESET_OFFSET_DRC0 25
+#define AHB_RESET_OFFSET_DE_FE0 14
+#define AHB_RESET_OFFSET_DE_BE0 12
+#define AHB_RESET_OFFSET_HDMI 11
+#define AHB_RESET_OFFSET_LCD1 5
+#define AHB_RESET_OFFSET_LCD0 4
+
+/* ahb_reset2 offsets */
+#define AHB_RESET_OFFSET_LVDS 0
+
+/* apb2 reset */
+#define APB2_RESET_UART_SHIFT (16)
+#define APB2_RESET_UART_MASK (0xff << APB2_RESET_UART_SHIFT)
+#define APB2_RESET_TWI_SHIFT (0)
+#define APB2_RESET_TWI_MASK (0xf << APB2_RESET_TWI_SHIFT)
+
+
+#ifndef __ASSEMBLY__
+void clock_set_pll1(unsigned int hz);
+void clock_set_pll5(unsigned int clk);
+unsigned int clock_get_pll6(void);
+#endif
+
+#endif /* _SUNXI_CLOCK_SUN8I_A83T_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 07/10] sunxi: Add support for Allwinner A83T DRAM
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (5 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks " Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:25 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 08/10] sunxi: do not include display for A83T Vishnu Patekar
` (3 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Add support for A83T dram. Register are different from sun8i A33.
init code is similar to A33 dram init.
hope we'll shift duplicate code in dram_sun8i_*
to dram helper in future.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/cpu/armv7/sunxi/Makefile | 2 +
arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424 ++++++++++++++++++++++
arch/arm/include/asm/arch-sunxi/dram.h | 2 +
arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++
4 files changed, 629 insertions(+)
create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
index 3c9fed3..c558016 100644
--- a/arch/arm/cpu/armv7/sunxi/Makefile
+++ b/arch/arm/cpu/armv7/sunxi/Makefile
@@ -54,5 +54,7 @@ obj-$(CONFIG_MACH_SUN6I) += dram_sun6i.o
obj-$(CONFIG_MACH_SUN7I) += dram_sun4i.o
obj-$(CONFIG_MACH_SUN8I_A23) += dram_sun8i_a23.o
obj-$(CONFIG_MACH_SUN8I_A33) += dram_sun8i_a33.o
+obj-$(CONFIG_MACH_SUN8I_A83T) += dram_sun8i_a83t.o
+
obj-y += fel_utils.o
endif
diff --git a/arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
new file mode 100644
index 0000000..d757e40
--- /dev/null
+++ b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
@@ -0,0 +1,424 @@
+/*
+ * Sun8i a33 platform dram controller init.
+ *
+ * (C) Copyright 2007-2015 Allwinner Technology Co.
+ * Jerry Wang <wangflord@allwinnertech.com>
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/dram.h>
+#include <asm/arch/prcm.h>
+
+#define DRAM_CLK_MUL 2
+#define DRAM_CLK_DIV 1
+
+struct dram_para {
+ u8 cs1;
+ u8 seq;
+ u8 bank;
+ u8 rank;
+ u8 rows;
+ u8 bus_width;
+ u16 page_size;
+};
+
+static void mctl_set_cr(struct dram_para *para)
+{
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+
+ writel(MCTL_CR_CS1_CONTROL(para->cs1) | MCTL_CR_UNKNOWN |
+ MCTL_CR_CHANNEL(1) | MCTL_CR_DDR3 |
+ (para->seq ? MCTL_CR_SEQUENCE : 0) |
+ ((para->bus_width == 16) ? MCTL_CR_BUSW16 : MCTL_CR_BUSW8) |
+ MCTL_CR_PAGE_SIZE(para->page_size) | MCTL_CR_ROW(para->rows) |
+ MCTL_CR_BANK(para->bank) | MCTL_CR_RANK(para->rank),
+ &mctl_com->cr);
+}
+
+static void auto_detect_dram_size(struct dram_para *para)
+{
+ u8 orig_rank = para->rank;
+ int rows, columns;
+
+ /* Row detect */
+ para->page_size = 512;
+ para->seq = 1;
+ para->rows = 16;
+ para->rank = 1;
+ mctl_set_cr(para);
+ for (rows = 11 ; rows < 16 ; rows++) {
+ if (mctl_mem_matches(1 << (rows + 9))) /* row-column */
+ break;
+ }
+
+ /* Column (page size) detect */
+ para->rows = 11;
+ para->page_size = 8192;
+ mctl_set_cr(para);
+ for (columns = 9 ; columns < 13 ; columns++) {
+ if (mctl_mem_matches(1 << columns))
+ break;
+ }
+
+ para->seq = 0;
+ para->rank = orig_rank;
+ para->rows = rows;
+ para->page_size = 1 << columns;
+ mctl_set_cr(para);
+}
+
+static inline int ns_to_t(int nanoseconds)
+{
+ const unsigned int ctrl_freq =
+ CONFIG_DRAM_CLK * DRAM_CLK_MUL / DRAM_CLK_DIV;
+
+ return (ctrl_freq * nanoseconds + 999) / 1000;
+}
+
+static void auto_set_timing_para(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ u32 reg_val;
+
+ u8 tccd = 2;
+ u8 tfaw = ns_to_t(50);
+ u8 trrd = max(ns_to_t(10), 4);
+ u8 trcd = ns_to_t(15);
+ u8 trc = ns_to_t(53);
+ u8 txp = max(ns_to_t(8), 3);
+ u8 twtr = max(ns_to_t(8), 4);
+ u8 trtp = max(ns_to_t(8), 4);
+ u8 twr = max(ns_to_t(15), 3);
+ u8 trp = ns_to_t(15);
+ u8 tras = ns_to_t(38);
+
+ u16 trefi = ns_to_t(7800) / 32;
+ u16 trfc = ns_to_t(350);
+
+ /* Fixed timing parameters */
+ u8 tmrw = 0;
+ u8 tmrd = 4;
+ u8 tmod = 12;
+ u8 tcke = 3;
+ u8 tcksrx = 5;
+ u8 tcksre = 5;
+ u8 tckesr = 4;
+ u8 trasmax = 24;
+ u8 tcl = 6; /* CL 12 */
+ u8 tcwl = 4; /* CWL 8 */
+ u8 t_rdata_en = 4;
+ u8 wr_latency = 2;
+
+ u32 tdinit0 = (500 * CONFIG_DRAM_CLK) + 1; /* 500us */
+ u32 tdinit1 = (360 * CONFIG_DRAM_CLK) / 1000 + 1; /* 360ns */
+ u32 tdinit2 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */
+ u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */
+
+ u8 twtp = tcwl + 2 + twr; /* WL + BL / 2 + tWR */
+ u8 twr2rd = tcwl + 2 + twtr; /* WL + BL / 2 + tWTR */
+ u8 trd2wr = tcl + 2 + 1 - tcwl; /* RL + BL / 2 + 2 - WL */
+
+ /* Set work mode register */
+ mctl_set_cr(para);
+ /* Set mode register */
+ writel(MCTL_MR0, &mctl_ctl->mr0);
+ writel(MCTL_MR1, &mctl_ctl->mr1);
+ writel(MCTL_MR2, &mctl_ctl->mr2);
+ writel(MCTL_MR3, &mctl_ctl->mr3);
+ /* Set dram timing */
+ reg_val = (twtp << 24) | (tfaw << 16) | (trasmax << 8) | (tras << 0);
+ writel(reg_val, &mctl_ctl->dramtmg0);
+ reg_val = (txp << 16) | (trtp << 8) | (trc << 0);
+ writel(reg_val, &mctl_ctl->dramtmg1);
+ reg_val = (tcwl << 24) | (tcl << 16) | (trd2wr << 8) | (twr2rd << 0);
+ writel(reg_val, &mctl_ctl->dramtmg2);
+ reg_val = (tmrw << 16) | (tmrd << 12) | (tmod << 0);
+ writel(reg_val, &mctl_ctl->dramtmg3);
+ reg_val = (trcd << 24) | (tccd << 16) | (trrd << 8) | (trp << 0);
+ writel(reg_val, &mctl_ctl->dramtmg4);
+ reg_val = (tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | (tcke << 0);
+ writel(reg_val, &mctl_ctl->dramtmg5);
+ /* Set two rank timing and exit self-refresh timing */
+ reg_val = readl(&mctl_ctl->dramtmg8);
+ reg_val &= ~(0xff << 8);
+ reg_val &= ~(0xff << 0);
+ reg_val |= (0x33 << 8);
+ reg_val |= (0x8 << 0);
+ writel(reg_val, &mctl_ctl->dramtmg8);
+ /* Set phy interface time */
+ reg_val = (0x2 << 24) | (t_rdata_en << 16) | (0x1 << 8)
+ | (wr_latency << 0);
+ /* PHY interface write latency and read latency configure */
+ writel(reg_val, &mctl_ctl->pitmg0);
+ /* Set phy time PTR0-2 use default */
+ writel(((tdinit0 << 0) | (tdinit1 << 20)), &mctl_ctl->ptr3);
+ writel(((tdinit2 << 0) | (tdinit3 << 20)), &mctl_ctl->ptr4);
+ /* Set refresh timing */
+ reg_val = (trefi << 16) | (trfc << 0);
+ writel(reg_val, &mctl_ctl->rfshtmg);
+}
+
+static void mctl_set_pir(u32 val)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ writel(val, &mctl_ctl->pir);
+ mctl_await_completion(&mctl_ctl->pgsr0, 0x1, 0x1);
+}
+
+static void mctl_data_train_cfg(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ if (para->rank == 2)
+ clrsetbits_le32(&mctl_ctl->dtcr, 0x3 << 24, 0x3 << 24);
+ else
+ clrsetbits_le32(&mctl_ctl->dtcr, 0x3 << 24, 0x1 << 24);
+}
+
+static int mctl_train_dram(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ mctl_data_train_cfg(para);
+ mctl_set_pir(0x5f3);
+
+ return ((readl(&mctl_ctl->pgsr0) >> 20) & 0xff) ? -EIO : 0;
+}
+
+static void set_master_priority(void)
+{
+ writel(0x00a0000d, MCTL_MASTER_CFG0(0));
+ writel(0x00500064, MCTL_MASTER_CFG1(0));
+ writel(0x07000009, MCTL_MASTER_CFG0(1));
+ writel(0x00000600, MCTL_MASTER_CFG1(1));
+ writel(0x01000009, MCTL_MASTER_CFG0(3));
+ writel(0x00000064, MCTL_MASTER_CFG1(3));
+ writel(0x08000009, MCTL_MASTER_CFG0(4));
+ writel(0x00000640, MCTL_MASTER_CFG1(4));
+ writel(0x20000308, MCTL_MASTER_CFG0(8));
+ writel(0x00001000, MCTL_MASTER_CFG1(8));
+ writel(0x02800009, MCTL_MASTER_CFG0(9));
+ writel(0x00000100, MCTL_MASTER_CFG1(9));
+ writel(0x01800009, MCTL_MASTER_CFG0(5));
+ writel(0x00000100, MCTL_MASTER_CFG1(5));
+ writel(0x01800009, MCTL_MASTER_CFG0(7));
+ writel(0x00000100, MCTL_MASTER_CFG1(7));
+ writel(0x00640009, MCTL_MASTER_CFG0(6));
+ writel(0x00000032, MCTL_MASTER_CFG1(6));
+ writel(0x0100000d, MCTL_MASTER_CFG0(2));
+ writel(0x00500080, MCTL_MASTER_CFG1(2));
+}
+
+static int mctl_channel_init(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+ u32 low_data_lines_status; /* Training status of datalines 0 - 7 */
+ u32 high_data_lines_status; /* Training status of datalines 8 - 15 */
+ u32 i, rval;
+
+ auto_set_timing_para(para);
+
+ /* Set dram master access priority */
+ writel(0x000101a0, &mctl_com->bwcr);
+ /* set cpu high priority */
+ writel(0x1, &mctl_com->mapr);
+ set_master_priority();
+ udelay(250);
+
+ /* Disable dram VTC */
+ clrbits_le32(&mctl_ctl->pgcr0, 0x3f << 0 | 0x1 << 30);
+ clrsetbits_le32(&mctl_ctl->pgcr1, 0x1 << 24, 0x1 << 26);
+
+ writel(0x94be6fa3, MCTL_PROTECT);
+ udelay(100);
+ clrsetbits_le32(MX_UPD2, 0xfff << 16, 0x50 << 26);
+ writel(0x0, MCTL_PROTECT);
+ udelay(100);
+
+
+ /* Set ODT */
+ if (IS_ENABLED(CONFIG_DRAM_ODT_EN))
+ rval = 0x0;
+ else
+ rval = 0x2;
+
+ for (i = 0 ; i < 11 ; i++) {
+ clrsetbits_le32(DATX0IOCR(i), (0x3 << 24) | (0x3 << 16),
+ rval << 24);
+ clrsetbits_le32(DATX1IOCR(i), (0x3 << 24) | (0x3 << 16),
+ rval << 24);
+ clrsetbits_le32(DATX2IOCR(i), (0x3 << 24) | (0x3 << 16),
+ rval << 24);
+ clrsetbits_le32(DATX3IOCR(i), (0x3 << 24) | (0x3 << 16),
+ rval << 24);
+ }
+
+ for (i = 0; i < 31; i++)
+ clrsetbits_le32(CAIOCR(i), 0x3 << 26 | 0x3 << 16, 0x2 << 26);
+
+ /* set PLL configuration */
+ if (CONFIG_DRAM_CLK >= 480)
+ setbits_le32(&mctl_ctl->pllgcr, 0x1 << 19);
+ else
+ setbits_le32(&mctl_ctl->pllgcr, 0x3 << 19);
+
+ /* Auto detect dram config, set 2 rank and 16bit bus-width */
+ para->cs1 = 0;
+ para->rank = 2;
+ para->bus_width = 16;
+ mctl_set_cr(para);
+
+ /* Open DQS gating */
+ clrbits_le32(&mctl_ctl->pgcr2, (0x3 << 6));
+ clrbits_le32(&mctl_ctl->dqsgmr, (0x1 << 8) | (0x7));
+
+ if (readl(&mctl_com->cr) & 0x1)
+ writel(0x00000303, &mctl_ctl->odtmap);
+ else
+ writel(0x00000201, &mctl_ctl->odtmap);
+
+ mctl_data_train_cfg(para);
+ /* ZQ calibration */
+ clrsetbits_le32(ZQnPR(0), 0x000000ff, CONFIG_DRAM_ZQ & 0xff);
+ clrsetbits_le32(ZQnPR(1), 0x000000ff, (CONFIG_DRAM_ZQ >> 8) & 0xff);
+ /* CA calibration */
+ mctl_set_pir(0x0201f3 | 0x1<<10);
+
+ /* DQS gate training */
+ if (mctl_train_dram(para) != 0) {
+ low_data_lines_status = (readl(DXnGSR0(0)) >> 24) & 0x03;
+ high_data_lines_status = (readl(DXnGSR0(1)) >> 24) & 0x03;
+
+ if (low_data_lines_status == 0x3)
+ return -EIO;
+
+ /* DRAM has only one rank */
+ para->rank = 1;
+ mctl_set_cr(para);
+
+ if (low_data_lines_status == high_data_lines_status)
+ goto done; /* 16 bit bus, 1 rank */
+
+ if (!(low_data_lines_status & high_data_lines_status)) {
+ /* Retry 16 bit bus-width with CS1 set */
+ para->cs1 = 1;
+ mctl_set_cr(para);
+ if (mctl_train_dram(para) == 0)
+ goto done;
+ }
+
+ /* Try 8 bit bus-width */
+ writel(0x0, DXnGCR0(1)); /* Disable high DQ */
+ para->cs1 = 0;
+ para->bus_width = 8;
+ mctl_set_cr(para);
+ if (mctl_train_dram(para) != 0)
+ return -EIO;
+ }
+done:
+ /* Check the dramc status */
+ mctl_await_completion(&mctl_ctl->statr, 0x1, 0x1);
+
+ /* Close DQS gating */
+ setbits_le32(&mctl_ctl->pgcr2, 0x3 << 6);
+
+ /* set PGCR3,CKE polarity */
+ writel(0x00aa0060, &mctl_ctl->pgcr3);
+ /* Enable master access */
+ writel(0xffffffff, &mctl_com->maer);
+
+ return 0;
+}
+
+static void mctl_sys_init(struct dram_para *para)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ clrbits_le32(&ccm->mbus_clk_cfg, MBUS_CLK_GATE);
+ clrbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
+ clrbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
+ clrbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
+ clrbits_le32(&ccm->pll5_cfg, CCM_PLL5_CTRL_EN);
+ clrbits_le32(&ccm->dram_clk_cfg, 0x01<<31);
+
+ clock_set_pll5(CONFIG_DRAM_CLK * 1000000 * DRAM_CLK_MUL);
+
+ clrsetbits_le32(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_DIV_MASK,
+ CCM_DRAMCLK_CFG_DIV(DRAM_CLK_DIV) |
+ CCM_DRAMCLK_CFG_RST | CCM_DRAMCLK_CFG_UPD);
+ mctl_await_completion(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_UPD, 0);
+
+ setbits_le32(&ccm->ahb_reset0_cfg, 1 << 14);
+ setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
+ setbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
+ setbits_le32(&ccm->mbus_clk_cfg, MBUS_CLK_GATE);
+
+ setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
+ setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
+ setbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
+ setbits_le32(&ccm->mbus_clk_cfg, MBUS_CLK_GATE);
+
+ /* Set dram master access priority */
+ writel(0x0000e00f, &mctl_ctl->clken); /* normal */
+
+ udelay(250);
+}
+
+unsigned long sunxi_dram_init(void)
+{
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ struct dram_para para = {
+ .cs1 = 0,
+ .bank = 1,
+ .rank = 1,
+ .rows = 15,
+ .bus_width = 16,
+ .page_size = 2048,
+ };
+
+ setbits_le32(SUNXI_PRCM_BASE + 0x1e0, 0x1 << 8);
+
+ writel(0, (SUNXI_PRCM_BASE + 0x1e8));
+ udelay(10);
+
+ mctl_sys_init(¶);
+
+ if (mctl_channel_init(¶) != 0)
+ return 0;
+
+ auto_detect_dram_size(¶);
+
+ /* Enable master software clk */
+ writel(readl(&mctl_com->swonr) | 0x3ffff, &mctl_com->swonr);
+
+ /* Set DRAM ODT MAP */
+ if (para.rank == 2)
+ writel(0x00000303, &mctl_ctl->odtmap);
+ else
+ writel(0x00000201, &mctl_ctl->odtmap);
+
+ return para.page_size * (para.bus_width / 8) *
+ (1 << (para.bank + para.rank + para.rows));
+}
diff --git a/arch/arm/include/asm/arch-sunxi/dram.h b/arch/arm/include/asm/arch-sunxi/dram.h
index 273f80f..bfe06a8 100644
--- a/arch/arm/include/asm/arch-sunxi/dram.h
+++ b/arch/arm/include/asm/arch-sunxi/dram.h
@@ -22,6 +22,8 @@
#include <asm/arch/dram_sun8i_a23.h>
#elif defined(CONFIG_MACH_SUN8I_A33)
#include <asm/arch/dram_sun8i_a33.h>
+#elif defined(CONFIG_MACH_SUN8I_A83T)
+#include <asm/arch/dram_sun8i_a83t.h>
#else
#include <asm/arch/dram_sun4i.h>
#endif
diff --git a/arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h b/arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
new file mode 100644
index 0000000..2891b71
--- /dev/null
+++ b/arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
@@ -0,0 +1,201 @@
+/*
+ * Sun8i platform dram controller register and constant defines
+ *
+ * (C) Copyright 2007-2015 Allwinner Technology Co.
+ * Jerry Wang <wangflord@allwinnertech.com>
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * (C) Copyright 2014-2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SUNXI_DRAM_SUN8I_A83T_H
+#define _SUNXI_DRAM_SUN8I_A83T_H
+
+struct sunxi_mctl_com_reg {
+ u32 cr; /* 0x00 */
+ u32 ccr; /* 0x04 controller configuration register */
+ u32 dbgcr; /* 0x08 */
+ u8 res0[0x4]; /* 0x0c */
+ u32 mcr0_0; /* 0x10 */
+ u32 mcr1_0; /* 0x14 */
+ u32 mcr0_1; /* 0x18 */
+ u32 mcr1_1; /* 0x1c */
+ u32 mcr0_2; /* 0x20 */
+ u32 mcr1_2; /* 0x24 */
+ u32 mcr0_3; /* 0x28 */
+ u32 mcr1_3; /* 0x2c */
+ u32 mcr0_4; /* 0x30 */
+ u32 mcr1_4; /* 0x34 */
+ u32 mcr0_5; /* 0x38 */
+ u32 mcr1_5; /* 0x3c */
+ u32 mcr0_6; /* 0x40 */
+ u32 mcr1_6; /* 0x44 */
+ u32 mcr0_7; /* 0x48 */
+ u32 mcr1_7; /* 0x4c */
+ u32 mcr0_8; /* 0x50 */
+ u32 mcr1_8; /* 0x54 */
+ u32 mcr0_9; /* 0x58 */
+ u32 mcr1_9; /* 0x5c */
+ u32 mcr0_10; /* 0x60 */
+ u32 mcr1_10; /* 0x64 */
+ u32 mcr0_11; /* 0x68 */
+ u32 mcr1_11; /* 0x6c */
+ u32 mcr0_12; /* 0x70 */
+ u32 mcr1_12; /* 0x74 */
+ u32 mcr0_13; /* 0x78 */
+ u32 mcr1_13; /* 0x7c */
+ u32 mcr0_14; /* 0x80 */
+ u32 mcr1_14; /* 0x84 */
+ u32 mcr0_15; /* 0x88 */
+ u32 mcr1_15; /* 0x8c */
+ u32 bwcr; /* 0x90 */
+ u32 maer; /* 0x94 */
+ u32 mapr; /* 0x98 */
+ u32 mcgcr; /* 0x9c */
+ u32 bwctr; /* 0xa0 */
+ u8 res2[0x8]; /* 0xa4 */
+ u32 swoffr; /* 0xac */
+ u8 res3[0x10]; /* 0xb0 */
+ u32 swonr; /* 0xc0 */
+ u8 res4[0x3c]; /* 0xc4 */
+ u32 mdfscr; /* 0x100 */
+ u32 mdfsmer; /* 0x104 */
+};
+
+struct sunxi_mctl_ctl_reg {
+ u32 pir; /* 0x00 */
+ u32 pwrctl; /* 0x04 */
+ u32 mrctrl0; /* 0x08 */
+ u32 clken; /* 0x0c */
+ u32 pgsr0; /* 0x10 */
+ u32 pgsr1; /* 0x14 */
+ u32 statr; /* 0x18 */
+ u8 res1[0x14]; /* 0x1c */
+ u32 mr0; /* 0x30 */
+ u32 mr1; /* 0x34 */
+ u32 mr2; /* 0x38 */
+ u32 mr3; /* 0x3c */
+ u32 pllgcr; /* 0x40 */
+ u32 ptr0; /* 0x44 */
+ u32 ptr1; /* 0x48 */
+ u32 ptr2; /* 0x4c */
+ u32 ptr3; /* 0x50 */
+ u32 ptr4; /* 0x54 */
+ u32 dramtmg0; /* 0x58 dram timing parameters register 0 */
+ u32 dramtmg1; /* 0x5c dram timing parameters register 1 */
+ u32 dramtmg2; /* 0x60 dram timing parameters register 2 */
+ u32 dramtmg3; /* 0x64 dram timing parameters register 3 */
+ u32 dramtmg4; /* 0x68 dram timing parameters register 4 */
+ u32 dramtmg5; /* 0x6c dram timing parameters register 5 */
+ u32 dramtmg6; /* 0x70 dram timing parameters register 6 */
+ u32 dramtmg7; /* 0x74 dram timing parameters register 7 */
+ u32 dramtmg8; /* 0x78 dram timing parameters register 8 */
+ u32 odtcfg; /* 0x7c */
+ u32 pitmg0; /* 0x80 */
+ u32 pitmg1; /* 0x84 */
+ u8 res2[0x4]; /* 0x88 */
+ u32 rfshctl0; /* 0x8c */
+ u32 rfshtmg; /* 0x90 */
+ u32 rfshctl1; /* 0x94 */
+ u32 pwrtmg; /* 0x98 */
+ u8 res3[0x20]; /* 0x9c */
+ u32 dqsgmr; /* 0xbc */
+ u32 dtcr; /* 0xc0 */
+ u32 dtar0; /* 0xc4 */
+ u32 dtar1; /* 0xc8 */
+ u32 dtar2; /* 0xcc */
+ u32 dtar3; /* 0xd0 */
+ u32 dtdr0; /* 0xd4 */
+ u32 dtdr1; /* 0xd8 */
+ u32 dtmr0; /* 0xdc */
+ u32 dtmr1; /* 0xe0 */
+ u32 dtbmr; /* 0xe4 */
+ u32 catr0; /* 0xe8 */
+ u32 catr1; /* 0xec */
+ u32 dtedr0; /* 0xf0 */
+ u32 dtedr1; /* 0xf4 */
+ u8 res4[0x8]; /* 0xf8 */
+ u32 pgcr0; /* 0x100 */
+ u32 pgcr1; /* 0x104 */
+ u32 pgcr2; /* 0x108 */
+ u32 pgcr3; /* 0x10c */
+ u32 iovcr0; /* 0x110 */
+ u32 iovcr1; /* 0x114 */
+ u32 dqsdr; /* 0x118 */
+ u32 dxccr; /* 0x11c */
+ u32 odtmap; /* 0x120 */
+ u32 zqctl0; /* 0x124 */
+ u32 zqctl1; /* 0x128 */
+ u8 res6[0x14]; /* 0x12c */
+ u32 zqncr; /* 0x140 zq control register 0 */
+ u32 zqnpr; /* 0x144 zq control register 1 */
+ u32 zqndr; /* 0x148 zq control register 2 */
+ u32 zqnsr; /* 0x14c zq status register 0 */
+ u32 res7; /* 0x150 zq status register 1 */
+ u8 res8[0x6c]; /* 0x154 */
+ u32 sched; /* 0x1c0 */
+ u32 perfhpr0; /* 0x1c4 */
+ u32 perfhpr1; /* 0x1c8 */
+ u32 perflpr0; /* 0x1cc */
+ u32 perflpr1; /* 0x1d0 */
+ u32 perfwr0; /* 0x1d4 */
+ u32 perfwr1; /* 0x1d8 */
+};
+
+
+#define ZQnPR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000144 + 0x10 * x)
+#define ZQnDR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000148 + 0x10 * x)
+#define ZQnSR(x) (SUNXI_DRAM_CTL0_BASE + 0x0000014c + 0x10 * x)
+
+#define DXnGTR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000340 + 0x80 * x)
+#define DXnGCR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000344 + 0x80 * x)
+#define DXnGSR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000348 + 0x80 * x)
+#define DXnGSR1(x) (SUNXI_DRAM_CTL0_BASE + 0x0000034c + 0x80 * x)
+#define DXnGSR2(x) (SUNXI_DRAM_CTL0_BASE + 0x00000350 + 0x80 * x)
+
+#define CAIOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000210 + 0x4 * (x))
+#define DXnMDLR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000300 + 0x80 * x)
+#define DXMDLR0 (SUNXI_DRAM_CTL0_BASE + 0x00000300)
+#define DXnLCDLR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000304 + 0x80 * x)
+#define DXnLCDLR1(x) (SUNXI_DRAM_CTL0_BASE + 0x00000308 + 0x80 * x)
+#define DXnLCDLR2(x) (SUNXI_DRAM_CTL0_BASE + 0x0000030c + 0x80 * x)
+#define DATX0IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000310 + 0x4 * x)
+#define DATX1IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000390 + 0x4 * x)
+#define DATX2IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000410 + 0x4 * x)
+#define DATX3IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000490 + 0x4 * x)
+#define MX_UPD0 (SUNXI_DRAM_CTL0_BASE + 0x00000880)
+#define MX_UPD2 (SUNXI_DRAM_CTL0_BASE + 0x00000888)
+
+#define MCTL_PROTECT (SUNXI_DRAM_COM_BASE + 0x800)
+#define MCTL_MASTER_CFG0(x) (SUNXI_DRAM_COM_BASE + 0x10 + 0x8 * x)
+#define MCTL_MASTER_CFG1(x) (SUNXI_DRAM_COM_BASE + 0x14 + 0x8 * x)
+
+/*
+ * DRAM common (sunxi_mctl_com_reg) register constants.
+ */
+#define MCTL_CR_RANK_MASK (3 << 0)
+#define MCTL_CR_RANK(x) (((x) - 1) << 0)
+#define MCTL_CR_BANK_MASK (3 << 2)
+#define MCTL_CR_BANK(x) ((x) << 2)
+#define MCTL_CR_ROW_MASK (0xf << 4)
+#define MCTL_CR_ROW(x) (((x) - 1) << 4)
+#define MCTL_CR_PAGE_SIZE_MASK (0xf << 8)
+#define MCTL_CR_PAGE_SIZE(x) ((fls(x) - 4) << 8)
+#define MCTL_CR_BUSW_MASK (7 << 12)
+#define MCTL_CR_BUSW8 (0 << 12)
+#define MCTL_CR_BUSW16 (1 << 12)
+#define MCTL_CR_SEQUENCE (1 << 15)
+#define MCTL_CR_DDR3 (3 << 16)
+#define MCTL_CR_CHANNEL_MASK (1 << 19)
+#define MCTL_CR_CHANNEL(x) (((x) - 1) << 19)
+#define MCTL_CR_UNKNOWN (0x4 << 20)
+#define MCTL_CR_CS1_CONTROL(x) ((x) << 24)
+
+/* DRAM control (sunxi_mctl_ctl_reg) register constants */
+#define MCTL_MR0 0x1c70 /* CL=11, WR=12 */
+#define MCTL_MR1 0x40
+#define MCTL_MR2 0x18 /* CWL=8 */
+#define MCTL_MR3 0x0
+
+#endif /* _SUNXI_DRAM_SUN8I_A83T_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 08/10] sunxi: do not include display for A83T
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (6 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 07/10] sunxi: Add support for Allwinner A83T DRAM Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:25 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 09/10] sunxi: dts: sun8i: Add Allwinner A83T dtsi Vishnu Patekar
` (2 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Currently, there no display support for A83T.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
board/sunxi/Kconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index ea69bf7..8dc3499 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -376,6 +376,7 @@ config AXP_GPIO
config VIDEO
boolean "Enable graphical uboot console on HDMI, LCD or VGA"
+ depends on !MACH_SUN8I_A83T
default y
---help---
Say Y here to add support for using a cfb console on the HDMI, LCD
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 09/10] sunxi: dts: sun8i: Add Allwinner A83T dtsi
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (7 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 08/10] sunxi: do not include display for A83T Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:26 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 10/10] sunxi: Add suport for A83T HomletV2 Board by Allwinner Vishnu Patekar
2015-11-13 16:52 ` [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Hans de Goede
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Allwinner A83T is new octa-core cortex-a7 SOC.
This adds the basic dtsi, the clocks differs from
earlier sun8i SOCs.
This is not yet included in kernel.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/dts/sun8i-a83t.dtsi | 247 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 247 insertions(+)
create mode 100644 arch/arm/dts/sun8i-a83t.dtsi
diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi
new file mode 100644
index 0000000..da1b451
--- /dev/null
+++ b/arch/arm/dts/sun8i-a83t.dtsi
@@ -0,0 +1,247 @@
+/*
+ * Copyright 2015 Vishnu Patekar
+ *
+ * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ cpu at 100 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <100>;
+ };
+
+ cpu at 101 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <101>;
+ };
+ cpu at 102 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <102>;
+ };
+
+ cpu at 103 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <103>;
+ };
+ };
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,cpu-registers-not-fw-configured;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+ };
+
+ soc at 01c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gic: interrupt-controller at 01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ pio: pinctrl at 01c20800 {
+ compatible = "allwinner,sun8i-a83t-pinctrl";
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01c20800 0x400>;
+ clocks = <&osc24M>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #gpio-cells = <3>;
+
+ i2c0_pins_a: i2c0 at 0 {
+ allwinner,pins = "PH0", "PH1";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins_a: i2c1 at 0 {
+ allwinner,pins = "PH2", "PH3";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins_a: i2c2 at 0 {
+ allwinner,pins = "PH4", "PH5";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0 at 0 {
+ allwinner,pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc1_pins_a: mmc1 at 0 {
+ allwinner,pins = "PG0", "PG1", "PG2",
+ "PG3", "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ allwinner,pins = "PC5", "PC6", "PC8",
+ "PC9", "PC10", "PC11",
+ "PC12", "PC13", "PC14",
+ "PC15";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart0_pins_a: uart0 at 0 {
+ allwinner,pins = "PF2", "PF4";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart0_pins_b: uart0 at 1 {
+ allwinner,pins = "PB9", "PB10";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ uart0: serial at 01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 10/10] sunxi: Add suport for A83T HomletV2 Board by Allwinner
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (8 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 09/10] sunxi: dts: sun8i: Add Allwinner A83T dtsi Vishnu Patekar
@ 2015-11-12 18:09 ` Vishnu Patekar
2015-11-13 17:27 ` Hans de Goede
2015-11-13 16:52 ` [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Hans de Goede
10 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-12 18:09 UTC (permalink / raw)
To: u-boot
Add dts and defconfig for h8homletv2 board.
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.
A83T patches are tested on this board.
For FEL mode it needs USB A-A(Male) cable. I used uart0 which
is multiplexed to microsd pins PF2 and PF4.
Enabled UART0 Header(PB9, PB10 pins).
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
---
arch/arm/dts/Makefile | 2 +
arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 +++++++++++++++++++++++
board/sunxi/MAINTAINERS | 5 ++
configs/h8_homlet_v2_defconfig | 26 +++++++++
4 files changed, 97 insertions(+)
create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
create mode 100644 configs/h8_homlet_v2_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8b656e9..d303eea 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -157,6 +157,8 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb
+dtb-$(CONFIG_MACH_SUN8I_A83T) += \
+ sun8i-a83t-allwinner-h8homlet-v2.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
new file mode 100644
index 0000000..342e1d3
--- /dev/null
+++ b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2015 Vishnu Patekar
+ * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+/ {
+ model = "Allwinner A83T H8Homlet Proto Dev Board v2.0";
+ compatible = "allwinner,h8homlet-v2", "allwinner,sun8i-a83t";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_b>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 96c4f3a..c0c2bdd 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -99,6 +99,11 @@ M: Priit Laes <plaes@plaes.org>
S: Maintained
F: configs/sunxi_Gemei_G9_defconfig
+H8HOMLET PROTO A83T BOARD
+M: VishnuPatekar <vishnupatekar0510@gmail.com>
+S: Maintained
+F: configs/h8_homlet_v2_defconfig
+
HUMMINGBIRD-A31 BOARD
M: Chen-Yu Tsai <wens@csie.org>
S: Maintained
diff --git a/configs/h8_homlet_v2_defconfig b/configs/h8_homlet_v2_defconfig
new file mode 100644
index 0000000..b78a240
--- /dev/null
+++ b/configs/h8_homlet_v2_defconfig
@@ -0,0 +1,26 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A83T=y
+CONFIG_DRAM_CLK=480
+CONFIG_DRAM_ZQ=15355
+CONFIG_DRAM_ODT_EN=y
+#CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+#CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
+#CONFIG_USB_MUSB_HOST=y
+CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-allwinner-h8homlet-v2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=1"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DCDC1_VOLT=3000
+CONFIG_AXP_DCDC2_VOLT=900
+CONFIG_AXP_DCDC3_VOLT=900
+CONFIG_AXP_DCDC4_VOLT=0
+CONFIG_AXP_DCDC5_VOLT=1500
+CONFIG_AXP_ALDO2_VOLT=0
+CONFIG_AXP_ALDO3_VOLT=0
+CONFIG_AXP_DLDO4_VOLT=0
--
1.9.1
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC.
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
` (9 preceding siblings ...)
2015-11-12 18:09 ` [U-Boot] [PATCH 10/10] sunxi: Add suport for A83T HomletV2 Board by Allwinner Vishnu Patekar
@ 2015-11-13 16:52 ` Hans de Goede
2015-11-13 17:05 ` Chen-Yu Tsai
2015-11-14 18:32 ` Vishnu Patekar
10 siblings, 2 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 16:52 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> This patch series adds basic support for Allwinner A83T SOC.
>
> Allwinner A83T is octa-core cortex-a7 based SoC.
> It's clock control unit and prcm, pinmux are different from previous sun8i
> series.
> Its processor cores are arragned in two clusters 4 cores each,
> similar to A80.
>
> Only basic clocks are enabled pll1, pll5, pll6.
> SMP, display, other peripherals support is not yet supported.
Cool stuff, great work! I've a number of comments, I will reply
to the individual patches with those.
I've tried to get this to run on my own h8_homlet_v2 but
unfortunately I cannot get it to work. My own board does
boot into some chinese top-set-box environment when booting
without a sdcard and connected to a tv. But it does not show
any output on the uart connector at the bottom right of the
board (I've tried with 2 different adapters, including the
one from the Merrii A80 board which has the exact same connector
on the board).
Not having an uart also means that I cannot get the board into
FEL mode (I do have a usb A <-> A cable).
I wonder if my board has a broken uart, or if the system
image uses a different uart by default ?
Have you tried booting with u-boot written to sdcard with
this patch-set ? Does this work, and does the SPL header
get printend on the bottom right uart connector ?
Regards,
Hans
> This enables booting kernel with initramfs, kernel patch v1 have been sent.
> I'll send v2 with comments addressed.
>
> Vishnu Patekar (10):
> sunxi: Add Machine Support for A83T SOC
> sunxi: Add support for UART0 in PB pin group on A83T
> sunxi: power: axp818: add support for axp818 driver
> sunxi: power: enabled support for axp818
> sunxi: do not enable smp for A83T
> sunxi: clk: add basic clocks for A83T
> sunxi: Add support for Allwinner A83T DRAM
> sunxi: do not include display for A83T
> sunxi: dts: sun8i: Add Allwinner A83T dtsi
> sunxi: Add suport for A83T HomletV2 Board by Allwinner
>
> arch/arm/cpu/armv7/sunxi/Makefile | 7 +
> arch/arm/cpu/armv7/sunxi/board.c | 8 +-
> arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++
> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 +
> arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424 +++++++++++++++++++++
> arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +
> arch/arm/dts/Makefile | 2 +
> arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 ++++
> arch/arm/dts/sun8i-a83t.dtsi | 247 ++++++++++++
> arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
> arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++
> arch/arm/include/asm/arch-sunxi/dram.h | 2 +
> arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++
> arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
> board/sunxi/Kconfig | 12 +-
> board/sunxi/MAINTAINERS | 5 +
> board/sunxi/board.c | 8 +
> configs/h8_homlet_v2_defconfig | 26 ++
> drivers/power/Kconfig | 34 +-
> drivers/power/Makefile | 1 +
> drivers/power/axp818.c | 132 +++++++
> include/axp818.h | 75 ++++
> include/axp_pmic.h | 3 +
> include/configs/sun8i.h | 2 +
> include/configs/sunxi-common.h | 2 +-
> 25 files changed, 1698 insertions(+), 16 deletions(-)
> create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
> create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
> create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
> create mode 100644 arch/arm/dts/sun8i-a83t.dtsi
> create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
> create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
> create mode 100644 configs/h8_homlet_v2_defconfig
> create mode 100644 drivers/power/axp818.c
> create mode 100644 include/axp818.h
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC.
2015-11-13 16:52 ` [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Hans de Goede
@ 2015-11-13 17:05 ` Chen-Yu Tsai
2015-11-14 18:32 ` Vishnu Patekar
1 sibling, 0 replies; 28+ messages in thread
From: Chen-Yu Tsai @ 2015-11-13 17:05 UTC (permalink / raw)
To: u-boot
On Sat, Nov 14, 2015 at 12:52 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Hi,
>
> On 12-11-15 19:09, Vishnu Patekar wrote:
>>
>> This patch series adds basic support for Allwinner A83T SOC.
>>
>> Allwinner A83T is octa-core cortex-a7 based SoC.
>> It's clock control unit and prcm, pinmux are different from previous sun8i
>> series.
>> Its processor cores are arragned in two clusters 4 cores each,
>> similar to A80.
>>
>> Only basic clocks are enabled pll1, pll5, pll6.
>> SMP, display, other peripherals support is not yet supported.
>
>
> Cool stuff, great work! I've a number of comments, I will reply
> to the individual patches with those.
>
> I've tried to get this to run on my own h8_homlet_v2 but
> unfortunately I cannot get it to work. My own board does
> boot into some chinese top-set-box environment when booting
> without a sdcard and connected to a tv. But it does not show
> any output on the uart connector at the bottom right of the
> board (I've tried with 2 different adapters, including the
> one from the Merrii A80 board which has the exact same connector
> on the board).
IIRC the onboard firmware actually uses the micro SD for UART.
> Not having an uart also means that I cannot get the board into
> FEL mode (I do have a usb A <-> A cable).
>
> I wonder if my board has a broken uart, or if the system
> image uses a different uart by default ?
>
> Have you tried booting with u-boot written to sdcard with
> this patch-set ? Does this work, and does the SPL header
> get printend on the bottom right uart connector ?
It's actually the bottom left. Not sure why the wiki page is wrong.
Anyway, I didn't get any output either. I haven't gone into finding
the problem though, and won't be able to until next week.
Regards
ChenYu
> Regards,
>
> Hans
>
>
>
>
>> This enables booting kernel with initramfs, kernel patch v1 have been
>> sent.
>> I'll send v2 with comments addressed.
>>
>> Vishnu Patekar (10):
>> sunxi: Add Machine Support for A83T SOC
>> sunxi: Add support for UART0 in PB pin group on A83T
>> sunxi: power: axp818: add support for axp818 driver
>> sunxi: power: enabled support for axp818
>> sunxi: do not enable smp for A83T
>> sunxi: clk: add basic clocks for A83T
>> sunxi: Add support for Allwinner A83T DRAM
>> sunxi: do not include display for A83T
>> sunxi: dts: sun8i: Add Allwinner A83T dtsi
>> sunxi: Add suport for A83T HomletV2 Board by Allwinner
>>
>> arch/arm/cpu/armv7/sunxi/Makefile | 7 +
>> arch/arm/cpu/armv7/sunxi/board.c | 8 +-
>> arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++
>> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 +
>> arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424
>> +++++++++++++++++++++
>> arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +
>> arch/arm/dts/Makefile | 2 +
>> arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 ++++
>> arch/arm/dts/sun8i-a83t.dtsi | 247 ++++++++++++
>> arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
>> arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++
>> arch/arm/include/asm/arch-sunxi/dram.h | 2 +
>> arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++
>> arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
>> board/sunxi/Kconfig | 12 +-
>> board/sunxi/MAINTAINERS | 5 +
>> board/sunxi/board.c | 8 +
>> configs/h8_homlet_v2_defconfig | 26 ++
>> drivers/power/Kconfig | 34 +-
>> drivers/power/Makefile | 1 +
>> drivers/power/axp818.c | 132 +++++++
>> include/axp818.h | 75 ++++
>> include/axp_pmic.h | 3 +
>> include/configs/sun8i.h | 2 +
>> include/configs/sunxi-common.h | 2 +-
>> 25 files changed, 1698 insertions(+), 16 deletions(-)
>> create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
>> create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
>> create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
>> create mode 100644 arch/arm/dts/sun8i-a83t.dtsi
>> create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>> create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
>> create mode 100644 configs/h8_homlet_v2_defconfig
>> create mode 100644 drivers/power/axp818.c
>> create mode 100644 include/axp818.h
>>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for A83T SOC
2015-11-12 18:09 ` [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for " Vishnu Patekar
@ 2015-11-13 17:19 ` Hans de Goede
2015-11-14 18:35 ` Vishnu Patekar
0 siblings, 1 reply; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:19 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Allwinner A83T is octa-core cortex-a7 SOC.
>
> This enables support for A83T.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
> ---
> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 ++
> board/sunxi/Kconfig | 11 ++++++++++-
> include/configs/sun8i.h | 2 ++
> 3 files changed, 14 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/cpu/armv7/sunxi/cpu_info.c b/arch/arm/cpu/armv7/sunxi/cpu_info.c
> index 05fef32..c9b4bc0 100644
> --- a/arch/arm/cpu/armv7/sunxi/cpu_info.c
> +++ b/arch/arm/cpu/armv7/sunxi/cpu_info.c
> @@ -71,6 +71,8 @@ int print_cpuinfo(void)
> puts("CPU: Allwinner A33 (SUN8I)\n");
> #elif defined CONFIG_MACH_SUN9I
> puts("CPU: Allwinner A80 (SUN9I)\n");
> +#elif defined CONFIG_MACH_SUN8I_A83T
> + puts("CPU: Allwinner A83T (SUN8I)\n");
> #else
> #warning Please update cpu_info.c with correct CPU information
> puts("CPU: SUNXI Family\n");
> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
> index f6f2a60..ea69bf7 100644
> --- a/board/sunxi/Kconfig
> +++ b/board/sunxi/Kconfig
> @@ -68,6 +68,15 @@ config MACH_SUN8I_A33
> select SUPPORT_SPL
> select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
>
> +config MACH_SUN8I_A83T
> + bool "sun8i (Allwinner A83T)"
> + select CPU_V7
> + select CPU_V7_HAS_NONSEC
> + select CPU_V7_HAS_VIRT
> + select SUNXI_GEN_SUN6I
> + select SUPPORT_SPL
> + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
Please remove the CPU_V7_HAS_NONSEC, CPU_V7_HAS_VIRT and ARMV7_BOOT_SEC_DEFAULT
options here, these imply enabling PSCI support and we do not yet have PSCI
code for the A83t. This is also why you need to add RMV7_BOOT_SEC_DEFAULT=y
to your defconfig to get things to work.
We will need to figure out SMP support later for now just leave these out.
> +
> config MACH_SUN9I
> bool "sun9i (Allwinner A80)"
> select CPU_V7
> @@ -78,7 +87,7 @@ endchoice
> # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
> config MACH_SUN8I
> bool
> - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33
> + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_A83T
>
>
> config DRAM_CLK
> diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h
> index 4fc6365..c139e0a 100644
> --- a/include/configs/sun8i.h
> +++ b/include/configs/sun8i.h
> @@ -25,6 +25,8 @@
> #define CONFIG_ARMV7_PSCI_NR_CPUS 2
> #elif defined(CONFIG_MACH_SUN8I_A33)
> #define CONFIG_ARMV7_PSCI_NR_CPUS 4
> +#elif defined(CONFIG_MACH_SUN8I_A83T)
> +#define CONFIG_ARMV7_PSCI_NR_CPUS 8
> #else
> #error Unsupported sun8i variant
> #endif
>
And this can be dropped too then.
Regards,
Hans
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 02/10] sunxi: Add support for UART0 in PB pin group on A83T
2015-11-12 18:09 ` [U-Boot] [PATCH 02/10] sunxi: Add support for UART0 in PB pin group on A83T Vishnu Patekar
@ 2015-11-13 17:19 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:19 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> On A83T, PB9,PB10 are UART0 pins.
> On allwinner A83T Dev board(h8homlet), this uart0 serial connector
> is exposed.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
This one looks good as is.
Regards,
Hans
> ---
> arch/arm/cpu/armv7/sunxi/board.c | 4 ++++
> arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
> 2 files changed, 5 insertions(+)
>
> diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c
> index 4785ac6..348f028 100644
> --- a/arch/arm/cpu/armv7/sunxi/board.c
> +++ b/arch/arm/cpu/armv7/sunxi/board.c
> @@ -72,6 +72,10 @@ static int gpio_init(void)
> sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_A33_GPB_UART0);
> sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_A33_GPB_UART0);
> sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP);
> +#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_A83T)
> + sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_A83T_GPB_UART0);
> + sunxi_gpio_set_cfgpin(SUNXI_GPB(10), SUN8I_A83T_GPB_UART0);
> + sunxi_gpio_set_pull(SUNXI_GPB(10), SUNXI_GPIO_PULL_UP);
> #elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
> sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
> sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
> diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h
> index 8382101..14a3328 100644
> --- a/arch/arm/include/asm/arch-sunxi/gpio.h
> +++ b/arch/arm/include/asm/arch-sunxi/gpio.h
> @@ -157,6 +157,7 @@ enum sunxi_gpio_number {
> #define SUN5I_GPB_UART0 2
> #define SUN8I_GPB_UART2 2
> #define SUN8I_A33_GPB_UART0 3
> +#define SUN8I_A83T_GPB_UART0 2
>
> #define SUNXI_GPC_NAND 2
> #define SUNXI_GPC_SDC2 3
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver
2015-11-12 18:09 ` [U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver Vishnu Patekar
@ 2015-11-13 17:21 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:21 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
> It's registers are different and calculating reg config is different than
> that of earlier axp power ICs.
>
> DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
> all other voltages can be added subsequently.
> AXP datasheet is uploaded to wiki:
> http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
> ---
> drivers/power/Kconfig | 34 ++++++++-----
> drivers/power/Makefile | 1 +
> drivers/power/axp818.c | 132 +++++++++++++++++++++++++++++++++++++++++++++++++
> include/axp818.h | 75 ++++++++++++++++++++++++++++
> include/axp_pmic.h | 3 ++
> 5 files changed, 234 insertions(+), 11 deletions(-)
> create mode 100644 drivers/power/axp818.c
> create mode 100644 include/axp818.h
>
> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
> index 809f8f1..d2494d4 100644
> --- a/drivers/power/Kconfig
> +++ b/drivers/power/Kconfig
> @@ -8,7 +8,8 @@ choice
> prompt "Select Sunxi PMIC Variant"
> depends on ARCH_SUNXI
> default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
> - default AXP221_POWER if MACH_SUN6I || MACH_SUN8I
> + default AXP221_POWER if MACH_SUN6I || MACH_SUN8I && !MACH_SUN8I_A83T
This will become unmanagable once we also get support for the H3 please change this to:
default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
> + default AXP818_POWER if MACH_SUN8I_A83T
>
> config SUNXI_NO_PMIC
> boolean "board without a pmic"
> @@ -31,16 +32,24 @@ config AXP209_POWER
>
> config AXP221_POWER
> boolean "axp221 / axp223 pmic support"
> - depends on MACH_SUN6I || MACH_SUN8I
> + depends on MACH_SUN6I || MACH_SUN8I || !MACH_SUN8I_A83T
Idem.
> ---help---
> Select this to enable support for the axp221/axp223 pmic found on most
> A23 and A31 boards.
>
> +config AXP818_POWER
> + boolean "axp818 pmic support"
> + depends on MACH_SUN8I_A83T
> + ---help---
> + Say y here to enable support for the axp818 pmic found on
> + A83T dev board.
> +
> endchoice
>
> config AXP_DCDC1_VOLT
> int "axp pmic dcdc1 voltage"
> - depends on AXP221_POWER
> + depends on AXP221_POWER || AXP818_POWER
> + default 3300 if AXP818_POWER
> default 3000 if MACH_SUN6I || MACH_SUN8I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
Please add a comment to the --help-- what this voltage is used for (assuming
that you know). The same goes for all the other voltage settings, otherwise
this patch looks good.
Regards,
Hans
> @@ -51,7 +60,8 @@ config AXP_DCDC1_VOLT
>
> config AXP_DCDC2_VOLT
> int "axp pmic dcdc2 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
> + default 900 if AXP818_POWER
> default 1400 if AXP152_POWER || AXP209_POWER
> default 1200 if MACH_SUN6I
> default 1100 if MACH_SUN8I
> @@ -64,7 +74,8 @@ config AXP_DCDC2_VOLT
>
> config AXP_DCDC3_VOLT
> int "axp pmic dcdc3 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
> + default 900 if AXP818_POWER
> default 1500 if AXP152_POWER
> default 1250 if AXP209_POWER
> default 1200 if MACH_SUN6I || MACH_SUN8I
> @@ -78,7 +89,7 @@ config AXP_DCDC3_VOLT
>
> config AXP_DCDC4_VOLT
> int "axp pmic dcdc4 voltage"
> - depends on AXP152_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP221_POWER || AXP818_POWER
> default 1250 if AXP152_POWER
> default 1200 if MACH_SUN6I
> default 0 if MACH_SUN8I
> @@ -91,7 +102,8 @@ config AXP_DCDC4_VOLT
>
> config AXP_DCDC5_VOLT
> int "axp pmic dcdc5 voltage"
> - depends on AXP221_POWER
> + depends on AXP221_POWER || AXP818_POWER
> + default 1800 if AXP818_POWER
> default 1500 if MACH_SUN6I || MACH_SUN8I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
> @@ -111,7 +123,7 @@ config AXP_ALDO1_VOLT
>
> config AXP_ALDO2_VOLT
> int "axp pmic (a)ldo2 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
> default 3000 if AXP152_POWER || AXP209_POWER
> default 0 if MACH_SUN6I
> default 2500 if MACH_SUN8I
> @@ -125,8 +137,8 @@ config AXP_ALDO2_VOLT
>
> config AXP_ALDO3_VOLT
> int "axp pmic (a)ldo3 voltage"
> - depends on AXP209_POWER || AXP221_POWER
> - default 0 if AXP209_POWER
> + depends on AXP209_POWER || AXP221_POWER || AXP818_POWER
> + default 0 if AXP209_POWER || AXP818_POWER
> default 3000 if MACH_SUN6I || MACH_SUN8I
> ---help---
> Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
> @@ -171,7 +183,7 @@ config AXP_DLDO3_VOLT
>
> config AXP_DLDO4_VOLT
> int "axp pmic dldo4 voltage"
> - depends on AXP221_POWER
> + depends on AXP221_POWER || AXP818_POWER
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
> diff --git a/drivers/power/Makefile b/drivers/power/Makefile
> index a2d3c04..0fdbca3 100644
> --- a/drivers/power/Makefile
> +++ b/drivers/power/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_AS3722_POWER) += as3722.o
> obj-$(CONFIG_AXP152_POWER) += axp152.o
> obj-$(CONFIG_AXP209_POWER) += axp209.o
> obj-$(CONFIG_AXP221_POWER) += axp221.o
> +obj-$(CONFIG_AXP818_POWER) += axp818.o
> obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
> obj-$(CONFIG_FTPMU010_POWER) += ftpmu010.o
> obj-$(CONFIG_TPS6586X_POWER) += tps6586x.o
> diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
> new file mode 100644
> index 0000000..4b21a83
> --- /dev/null
> +++ b/drivers/power/axp818.c
> @@ -0,0 +1,132 @@
> +/*
> + * AXP818 driver based on AXP221 driver
> + *
> + *
> + * (C) Copyright 2015 Vishnu Patekar <vishnuptekar0510@gmail.com>
> + *
> + * Based on axp221.c
> + * (C) Copyright 2014 Hans de Goede <hdegoede@redhat.com>
> + * (C) Copyright 2013 Oliver Schinagl <oliver@schinagl.nl>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/pmic_bus.h>
> +#include <axp_pmic.h>
> +
> +static u8 axp818_mvolt_to_cfg(int mvolt, int min, int max, int div)
> +{
> + if (mvolt < min)
> + mvolt = min;
> + else if (mvolt > max)
> + mvolt = max;
> +
> + return (mvolt - min) / div;
> +}
> +
> +int axp_set_dcdc1(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg = axp818_mvolt_to_cfg(mvolt, 1600, 3400, 100);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC1_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC1_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC1_EN);
> +}
> +
> +int axp_set_dcdc2(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1220)
> + cfg = 70 + axp818_mvolt_to_cfg(mvolt, 1220, 1300, 20);
> + else
> + cfg = axp818_mvolt_to_cfg(mvolt, 500, 1200, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC2_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC2_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC2_EN);
> +}
> +
> +int axp_set_dcdc3(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1220)
> + cfg = 70 + axp818_mvolt_to_cfg(mvolt, 1220, 1300, 20);
> + else
> + cfg = axp818_mvolt_to_cfg(mvolt, 500, 1200, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC3_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC3_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC3_EN);
> +}
> +
> +int axp_set_dcdc5(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1140)
> + cfg = 32 + axp818_mvolt_to_cfg(mvolt, 1140, 1840, 20);
> + else
> + cfg = axp818_mvolt_to_cfg(mvolt, 800, 1120, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC5_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC5_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC5_EN);
> +}
> +
> +int axp_init(void)
> +{
> + u8 axp_chip_id;
> + int ret;
> +
> + ret = pmic_bus_init();
> + if (ret)
> + return ret;
> +
> + ret = pmic_bus_read(AXP818_CHIP_ID, &axp_chip_id);
> + if (ret)
> + return ret;
> +
> + if (!(axp_chip_id == 0x51))
> + return -ENODEV;
> + else
> + return ret;
> +
> + return 0;
> +}
> diff --git a/include/axp818.h b/include/axp818.h
> new file mode 100644
> index 0000000..1dc6456
> --- /dev/null
> +++ b/include/axp818.h
> @@ -0,0 +1,75 @@
> +/*
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
> + *
> + * X-Powers AXP818 Power Management IC driver
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#define AXP818_CHIP_ID 0x03
> +
> +#define AXP818_OUTPUT_CTRL1 0x10
> +#define AXP818_OUTPUT_CTRL1_DCDC1_EN (1 << 0)
> +#define AXP818_OUTPUT_CTRL1_DCDC2_EN (1 << 1)
> +#define AXP818_OUTPUT_CTRL1_DCDC3_EN (1 << 2)
> +#define AXP818_OUTPUT_CTRL1_DCDC4_EN (1 << 3)
> +#define AXP818_OUTPUT_CTRL1_DCDC5_EN (1 << 4)
> +#define AXP818_OUTPUT_CTRL1_DCDC6_EN (1 << 5)
> +#define AXP818_OUTPUT_CTRL1_DCDC7_EN (1 << 6)
> +#define AXP818_OUTPUT_CTRL2 0x12
> +#define AXP818_OUTPUT_CTRL2_ELDO1_EN (1 << 0)
> +#define AXP818_OUTPUT_CTRL2_ELDO2_EN (1 << 1)
> +#define AXP818_OUTPUT_CTRL2_ELDO3_EN (1 << 2)
> +#define AXP818_OUTPUT_CTRL2_DLDO1_EN (1 << 3)
> +#define AXP818_OUTPUT_CTRL2_DLDO2_EN (1 << 4)
> +#define AXP818_OUTPUT_CTRL2_DLDO3_EN (1 << 5)
> +#define AXP818_OUTPUT_CTRL2_DLDO4_EN (1 << 6)
> +#define AXP818_OUTPUT_CTRL3 0x13
> +#define AXP818_OUTPUT_CTRL3_FLDO1_EN (1 << 2)
> +#define AXP818_OUTPUT_CTRL3_FLDO2_EN (1 << 3)
> +#define AXP818_OUTPUT_CTRL3_FLDO3_EN (1 << 4)
> +#define AXP818_OUTPUT_CTRL3_ALDO1_EN (1 << 5)
> +#define AXP818_OUTPUT_CTRL3_ALDO2_EN (1 << 6)
> +#define AXP818_OUTPUT_CTRL3_ALDO3_EN (1 << 7)
> +
> +#define AXP818_DCDC1_CTRL 0x20
> +#define AXP818_DCDC2_CTRL 0x21
> +#define AXP818_DCDC3_CTRL 0x22
> +#define AXP818_DCDC4_CTRL 0x23
> +#define AXP818_DCDC5_CTRL 0x24
> +#define AXP818_DCDC6_CTRL 0x25
> +
> +#define AXP818_DLDO1_CTRL 0x15
> +#define AXP818_DLDO2_CTRL 0x16
> +#define AXP818_DLDO3_CTRL 0x17
> +#define AXP818_DLDO4_CTRL 0x18
> +#define AXP818_ELDO1_CTRL 0x19
> +#define AXP818_ELDO2_CTRL 0x1a
> +#define AXP818_ELDO3_CTRL 0x1b
> +#define AXP818_ELDO3_CTRL 0x1b
> +#define AXP818_FLDO1_CTRL 0x1c
> +#define AXP818_FLDO2_3_CTRL 0x1d
> +#define AXP818_DCDC1_CTRL 0x20
> +#define AXP818_DCDC2_CTRL 0x21
> +#define AXP818_DCDC3_CTRL 0x22
> +#define AXP818_DCDC4_CTRL 0x23
> +#define AXP818_DCDC5_CTRL 0x24
> +#define AXP818_DCDC6_CTRL 0x25
> +#define AXP818_DCDC7_CTRL 0x26
> +
> +#define AXP818_ALDO1_CTRL 0x28
> +#define AXP818_ALDO2_CTRL 0x29
> +#define AXP818_ALDO3_CTRL 0x2a
> +
> +int axp818_init(void);
> +
> +/* For axp_gpio.c */
> +#define AXP_POWER_STATUS 0x00
> +#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
> +#define AXP_GPIO0_CTRL 0x90
> +#define AXP_GPIO1_CTRL 0x92
> +#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
> +#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
> +#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
> +#define AXP_GPIO_STATE 0x94
> +#define AXP_GPIO_STATE_OFFSET 0
> diff --git a/include/axp_pmic.h b/include/axp_pmic.h
> index ef339c4..3b01c49 100644
> --- a/include/axp_pmic.h
> +++ b/include/axp_pmic.h
> @@ -16,6 +16,9 @@
> #ifdef CONFIG_AXP221_POWER
> #include <axp221.h>
> #endif
> +#ifdef CONFIG_AXP818_POWER
> +#include <axp818.h>
> +#endif
>
> int axp_set_dcdc1(unsigned int mvolt);
> int axp_set_dcdc2(unsigned int mvolt);
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818
2015-11-12 18:09 ` [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818 Vishnu Patekar
@ 2015-11-13 17:24 ` Hans de Goede
2015-11-14 18:43 ` Vishnu Patekar
0 siblings, 1 reply; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:24 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Enabled support for AXP818 in SPL and u-boot.
> DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
> ---
> arch/arm/cpu/armv7/sunxi/Makefile | 1 +
> arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +++++++++++++++
> board/sunxi/board.c | 8 ++++++++
> include/configs/sunxi-common.h | 2 +-
> 4 files changed, 25 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
> index 459d5d8..929a933 100644
> --- a/arch/arm/cpu/armv7/sunxi/Makefile
> +++ b/arch/arm/cpu/armv7/sunxi/Makefile
> @@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_SUN6I) += tzpc.o
> obj-$(CONFIG_AXP152_POWER) += pmic_bus.o
> obj-$(CONFIG_AXP209_POWER) += pmic_bus.o
> obj-$(CONFIG_AXP221_POWER) += pmic_bus.o
> +obj-$(CONFIG_AXP818_POWER) += pmic_bus.o
>
> ifndef CONFIG_SPL_BUILD
> ifdef CONFIG_ARMV7_PSCI
> diff --git a/arch/arm/cpu/armv7/sunxi/pmic_bus.c b/arch/arm/cpu/armv7/sunxi/pmic_bus.c
> index 9e05127..838831d 100644
> --- a/arch/arm/cpu/armv7/sunxi/pmic_bus.c
> +++ b/arch/arm/cpu/armv7/sunxi/pmic_bus.c
> @@ -26,6 +26,9 @@
> #define AXP223_DEVICE_ADDR 0x3a3
> #define AXP223_RUNTIME_ADDR 0x2d
>
> +#define AXP818_DEVICE_ADDR 0x3a3
> +#define AXP818_RUNTIME_ADDR 0x2d
> +
These are exactly the same, please just add a comment that the
AXP818 addresses are the same as the AXP223 ones instead
of adding new defines.
> int pmic_bus_init(void)
> {
> /* This cannot be 0 because it is used in SPL before BSS is ready */
> @@ -49,6 +52,14 @@ int pmic_bus_init(void)
> # endif
> if (ret)
> return ret;
> +#elif defined CONFIG_AXP818_POWER
And instead of this #elif make the #if above:
#elif defined CONFIG_AXP223_POWER || defined CONFIG_AXP818_POWER
> + ret = rsb_init();
> + if (ret)
> + return ret;
> +
> + ret = rsb_set_device_address(AXP818_DEVICE_ADDR, AXP818_RUNTIME_ADDR);
> + if (ret)
> + return ret;
> #endif
>
> needs_init = 0;
> @@ -67,6 +78,8 @@ int pmic_bus_read(u8 reg, u8 *data)
> # else
> return rsb_read(AXP223_RUNTIME_ADDR, reg, data);
> # endif
> +#elif defined CONFIG_AXP818_POWER
> + return rsb_read(AXP818_RUNTIME_ADDR, reg, data);
> #endif
> }
>
> @@ -82,6 +95,8 @@ int pmic_bus_write(u8 reg, u8 data)
> # else
> return rsb_write(AXP223_RUNTIME_ADDR, reg, data);
> # endif
> +#elif CONFIG_AXP818_POWER
> + return rsb_write(AXP818_RUNTIME_ADDR, reg, data);
> #endif
> }
>
And idem for all the other functions.
> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
> index 6ac398c..ebfa94e 100644
> --- a/board/sunxi/board.c
> +++ b/board/sunxi/board.c
> @@ -430,6 +430,14 @@ void sunxi_board_init(void)
> int power_failed = 0;
> unsigned long ramsize;
>
> +#if defined CONFIG_AXP818_POWER
> + power_failed = axp_init();
> + power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
> + power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
> + power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
> + power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
> +#endif
> +
> #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER
> power_failed = axp_init();
>
Please do not add this AXP818 specific block, instead modify the block below
to work for the 818.
> diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
> index ddcfe94..61af897 100644
> --- a/include/configs/sunxi-common.h
> +++ b/include/configs/sunxi-common.h
> @@ -243,7 +243,7 @@ extern int soft_i2c_gpio_scl;
> #endif
>
> /* PMU */
> -#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER
> +#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
> #define CONFIG_SPL_POWER_SUPPORT
> #endif
>
>
Regards,
Hans
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 05/10] sunxi: do not enable smp for A83T
2015-11-12 18:09 ` [U-Boot] [PATCH 05/10] sunxi: do not enable smp for A83T Vishnu Patekar
@ 2015-11-13 17:24 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:24 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> When smp is enabled for A83T, intermittent hang is observed after booting kernel.
> for now do not enable the smp for CPU0. This has to be fixed.
> Also, fixed the space at line start warning at these two lines.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
> ---
> arch/arm/cpu/armv7/sunxi/board.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c
> index 348f028..e463e5b 100644
> --- a/arch/arm/cpu/armv7/sunxi/board.c
> +++ b/arch/arm/cpu/armv7/sunxi/board.c
> @@ -113,8 +113,8 @@ void s_init(void)
> setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
> #endif
> #if defined CONFIG_MACH_SUN6I || \
> - defined CONFIG_MACH_SUN7I || \
> - defined CONFIG_MACH_SUN8I
> + defined CONFIG_MACH_SUN7I || \
> + defined CONFIG_MACH_SUN8I && !(CONFIG_MACH_SUN8I_A83T)
> /* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
> asm volatile(
> "mrc p15, 0, r0, c1, c0, 1\n"
>
Please try again if this is still necessary when not trying to use
the PSCI code.
Regards,
Hans
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks for A83T
2015-11-12 18:09 ` [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks " Vishnu Patekar
@ 2015-11-13 17:25 ` Hans de Goede
2015-11-14 18:47 ` Vishnu Patekar
0 siblings, 1 reply; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:25 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Add basic clocks pll1, pll5, and some default values from allwinner u-boot.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
This one looks good as is.
Regards,
Hans
> ---
> arch/arm/cpu/armv7/sunxi/Makefile | 4 +
> arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++++
> arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
> arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++++++++
> 4 files changed, 444 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
> create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>
> diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
> index 929a933..3c9fed3 100644
> --- a/arch/arm/cpu/armv7/sunxi/Makefile
> +++ b/arch/arm/cpu/armv7/sunxi/Makefile
> @@ -26,7 +26,11 @@ obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o
> obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o
> obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o
> obj-$(CONFIG_MACH_SUN7I) += clock_sun4i.o
> +ifdef CONFIG_MACH_SUN8I_A83T
> +obj-y += clock_sun8i_a83t.o
> +else
> obj-$(CONFIG_MACH_SUN8I) += clock_sun6i.o
> +endif
> obj-$(CONFIG_MACH_SUN9I) += clock_sun9i.o
> obj-$(CONFIG_MACH_SUN6I) += tzpc.o
>
> diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c b/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
> new file mode 100644
> index 0000000..76efa93
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
> @@ -0,0 +1,133 @@
> +/*
> + * sun6i specific clock code
> + *
> + * (C) Copyright 2007-2012
> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
> + * Tom Cubie <tangliang@allwinnertech.com>
> + *
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/prcm.h>
> +#include <asm/arch/sys_proto.h>
> +
> +#ifdef CONFIG_SPL_BUILD
> +void clock_init_safe(void)
> +{
> + struct sunxi_ccm_reg * const ccm =
> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> +
> + clock_set_pll1(408000000);
> + /* enable pll_hsic, default is 480M */
> + writel(PLL8_CFG_DEFAULT, &ccm->pll8_cfg);
> + writel(readl(&ccm->pll8_cfg) | (0x1 << 31), &ccm->pll8_cfg);
> +
> + /* switch to default 24MHz before changing to hsic */
> + writel(0x0, &ccm->cci400_cfg);
> + sdelay(50);
> + writel(CCM_CCI400_CLK_SEL_HSIC, &ccm->cci400_cfg);
> + sdelay(100);
> +
> + /* switch before changing pll6 */
> + clrsetbits_le32(&ccm->ahb1_apb1_div, AHB1_CLK_SRC_MASK,
> + AHB1_CLK_SRC_OSC24M);
> + writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg);
> + sdelay(100);
> +
> + writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
> + writel(CCM_MBUS_RESET_RESET, &ccm->mbus_reset);
> + writel(MBUS_CLK_DEFAULT, &ccm->mbus_clk_cfg);
> +
> + /* timestamp */
> + writel(1, 0x01720000);
> +}
> +#endif
> +
> +void clock_init_uart(void)
> +{
> + struct sunxi_ccm_reg *const ccm =
> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> +
> + /* uart clock source is apb2 */
> + writel(APB2_CLK_SRC_OSC24M|
> + APB2_CLK_RATE_N_1|
> + APB2_CLK_RATE_M(1),
> + &ccm->apb2_div);
> +
> + /* open the clock for uart */
> + setbits_le32(&ccm->apb2_gate,
> + CLK_GATE_OPEN << (APB2_GATE_UART_SHIFT +
> + CONFIG_CONS_INDEX - 1));
> +
> + /* deassert uart reset */
> + setbits_le32(&ccm->apb2_reset_cfg,
> + 1 << (APB2_RESET_UART_SHIFT +
> + CONFIG_CONS_INDEX - 1));
> +}
> +
> +#ifdef CONFIG_SPL_BUILD
> +void clock_set_pll1(unsigned int clk)
> +{
> + struct sunxi_ccm_reg * const ccm =
> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> + const int p = 0;
> +
> + /* Switch to 24MHz clock while changing PLL1 */
> + writel(AXI_DIV_2 << AXI0_DIV_SHIFT |
> + CPU_CLK_SRC_OSC24M << C0_CPUX_CLK_SRC_SHIFT,
> + &ccm->cpu_axi_cfg);
> +
> + /* clk = 24*n/p, p is ignored if clock is >288MHz */
> + writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) | CMM_PLL1_CLOCK_TIME_2 |
> + CCM_PLL1_CTRL_N(clk / 24000000),
> + &ccm->pll1_c0_cfg);
> + sdelay(200);
> +
> + writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) | CMM_PLL1_CLOCK_TIME_2 |
> + CCM_PLL1_CTRL_N(clk / (24000000)),
> + &ccm->pll1_c1_cfg);
> + sdelay(200);
> +
> + /* Switch CPU to PLL1 */
> + writel(AXI_DIV_2 << AXI0_DIV_SHIFT |
> + AXI_DIV_2 << AXI1_DIV_SHIFT |
> + CPU_CLK_SRC_PLL1 << C0_CPUX_CLK_SRC_SHIFT |
> + CPU_CLK_SRC_PLL1 << C1_CPUX_CLK_SRC_SHIFT,
> + &ccm->cpu_axi_cfg);
> +}
> +#endif
> +
> +void clock_set_pll5(unsigned int clk)
> +{
> + struct sunxi_ccm_reg * const ccm =
> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> + unsigned int div1 = 0, div2 = 0;
> +
> + /* A83T PLL5 DDR rate = 24000000 * (n+1)/(div1+1)/(div2+1) */
> + writel(CCM_PLL5_CTRL_EN | CCM_PLL5_CTRL_UPD |
> + CCM_PLL5_CTRL_N(clk / (24000000)) |
> + div2 << CCM_PLL5_DIV2_SHIFT |
> + div1 << CCM_PLL5_DIV1_SHIFT, &ccm->pll5_cfg);
> +
> + udelay(5500);
> +}
> +
> +
> +unsigned int clock_get_pll6(void)
> +{
> + struct sunxi_ccm_reg *const ccm =
> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> +
> + uint32_t rval = readl(&ccm->pll6_cfg);
> + int n = ((rval & CCM_PLL6_CTRL_N_MASK) >> CCM_PLL6_CTRL_N_SHIFT) + 1;
> + int div1 = ((rval & CCM_PLL6_CTRL_DIV1_MASK) >>
> + CCM_PLL6_CTRL_DIV1_SHIFT) + 1;
> + int div2 = ((rval & CCM_PLL6_CTRL_DIV2_MASK) >>
> + CCM_PLL6_CTRL_DIV2_SHIFT) + 1;
> + return 24000000 * n / div1 / div2;
> +}
> diff --git a/arch/arm/include/asm/arch-sunxi/clock.h b/arch/arm/include/asm/arch-sunxi/clock.h
> index 3e5d999..8ca58ae 100644
> --- a/arch/arm/include/asm/arch-sunxi/clock.h
> +++ b/arch/arm/include/asm/arch-sunxi/clock.h
> @@ -15,7 +15,9 @@
> #define CLK_GATE_CLOSE 0x0
>
> /* clock control module regs definition */
> -#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I)
> +#if defined(CONFIG_MACH_SUN8I_A83T)
> +#include <asm/arch/clock_sun8i_a83t.h>
> +#elif defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I)
> #include <asm/arch/clock_sun6i.h>
> #elif defined(CONFIG_MACH_SUN9I)
> #include <asm/arch/clock_sun9i.h>
> diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h b/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
> new file mode 100644
> index 0000000..28ea16c
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
> @@ -0,0 +1,304 @@
> +/*
> + * sun8i a83t clock register definitions
> + *
> + * (C) Copyright 2007-2011
> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
> + * Tom Cubie <tangliang@allwinnertech.com>
> + *
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
> + * from sun6i.h
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef _SUNXI_CLOCK_SUN8I_A83T_H
> +#define _SUNXI_CLOCK_SUN8I_A83T_H
> +
> +struct sunxi_ccm_reg {
> + u32 pll1_c0_cfg; /* 0x00 c1cpu# pll control */
> + u32 pll1_c1_cfg; /* 0x04 c1cpu# pll control */
> + u32 pll2_cfg; /* 0x08 pll2 audio control */
> + u32 reserved1;
> + u32 pll3_cfg; /* 0x10 pll3 video0 control */
> + u32 reserved2;
> + u32 pll4_cfg; /* 0x18 pll4 ve control */
> + u32 reserved3;
> + u32 pll5_cfg; /* 0x20 pll5 ddr control */
> + u32 reserved4;
> + u32 pll6_cfg; /* 0x28 pll6 peripheral control */
> + u32 reserved5[3]; /* 0x2c */
> + u32 pll7_cfg; /* 0x38 pll7 gpu control */
> + u32 reserved6[2]; /* 3c */
> + u32 pll8_cfg; /* 0x44 pll8 hsic control */
> + u32 pll9_cfg; /* 0x48 pll9 de control */
> + u32 pll10_cfg; /* 0x4c pll10 video1 control */
> + u32 cpu_axi_cfg; /* 0x50 CPU/AXI divide ratio */
> + u32 ahb1_apb1_div; /* 0x54 AHB1/APB1 divide ratio */
> + u32 apb2_div; /* 0x58 APB2 divide ratio */
> + u32 ahb2_div; /* 0x5c AHB2 divide ratio */
> + u32 ahb_gate0; /* 0x60 ahb module clock gating 0 */
> + u32 ahb_gate1; /* 0x64 ahb module clock gating 1 */
> + u32 apb1_gate; /* 0x68 apb1 module clock gating 3 */
> + u32 apb2_gate; /* 0x6c apb2 module clock gating 4 */
> + u32 reserved7[2]; /* 0x70 */
> + u32 cci400_cfg; /* 0x78 cci400 clock configuration A83T only */
> + u32 reserved8; /* 0x7c */
> + u32 nand0_clk_cfg; /* 0x80 nand clock control */
> + u32 reserved9; /* 0x84 */
> + u32 sd0_clk_cfg; /* 0x88 sd0 clock control */
> + u32 sd1_clk_cfg; /* 0x8c sd1 clock control */
> + u32 sd2_clk_cfg; /* 0x90 sd2 clock control */
> + u32 sd3_clk_cfg; /* 0x94 sd3 clock control */
> + u32 reserved10; /* 0x98 */
> + u32 ss_clk_cfg; /* 0x9c security system clock control */
> + u32 spi0_clk_cfg; /* 0xa0 spi0 clock control */
> + u32 spi1_clk_cfg; /* 0xa4 spi1 clock control */
> + u32 reserved11[2]; /* 0xa8 */
> + u32 i2s0_clk_cfg; /* 0xb0 I2S0 clock control */
> + u32 i2s1_clk_cfg; /* 0xb4 I2S1 clock control */
> + u32 i2s2_clk_cfg; /* 0xb8 I2S2 clock control */
> + u32 tdm_clk_cfg; /* 0xbc TDM clock control */
> + u32 spdif_clk_cfg; /* 0xc0 SPDIF clock control */
> + u32 reserved12[2]; /* c4 */
> + u32 usb_clk_cfg; /* 0xcc USB clock control */
> + u32 reserved13[9]; /* d0 */
> + u32 dram_clk_cfg; /* 0xf4 DRAM configuration clock control */
> + u32 dram_pll_cfg; /* 0xf8 PLL_DDR cfg register */
> + u32 mbus_reset; /* 0xfc MBUS reset control */
> + u32 dram_clk_gate; /* 0x100 DRAM module gating */
> + u32 reserved14[5]; /* 0x104 BE0 */
> + u32 lcd0_clk_cfg; /* 0x118 LCD0 module clock */
> + u32 lcd1_clk_cfg; /* 0x11c LCD1 module clock */
> + u32 reserved15[4]; /* 0x120 */
> + u32 mipi_csi_clk_cfg; /* 0x130 MIPI CSI module clock */
> + u32 csi_clk_cfg; /* 0x134 CSI module clock */
> + u32 reserved16; /* 0x138 */
> + u32 ve_clk_cfg; /* 0x13c VE module clock */
> + u32 reserved17; /* 0x140 */
> + u32 avs_clk_cfg; /* 0x144 AVS module clock */
> + u32 reserved18[2]; /* 0x148 */
> + u32 hdmi_clk_cfg; /* 0x150 HDMI module clock */
> + u32 hdmi_slow_clk_cfg; /* 0x154 HDMI slow module clock */
> + u32 reserved19; /* 0x158 */
> + u32 mbus_clk_cfg; /* 0x15c MBUS module clock */
> + u32 reserved20[2];
> + u32 mipi_dsi_clk_cfg; /* 0x168 MIPI DSI clock control */
> + u32 reserved21[13]; /* 0x16c */
> + u32 gpu_core_clk_cfg; /* 0x1a0 GPU core clock config */
> + u32 gpu_mem_clk_cfg; /* 0x1a4 GPU memory clock config */
> + u32 gpu_hyd_clk_cfg; /* 0x1a8 GPU HYD clock config */
> + u32 reserved22[21]; /* 0x1ac */
> + u32 pll_stable0; /* 0x200 PLL stable time 0 */
> + u32 pll_stable1; /* 0x204 PLL stable time 1 */
> + u32 reserved23; /* 0x208 */
> + u32 pll_stable_status; /* 0x20c PLL stable status register */
> + u32 reserved24[0x04]; /* 0x210 */
> + u32 pll1_c0_bias_cfg; /* 0x220 PLL1 c0cpu# Bias config */
> + u32 pll2_bias_cfg; /* 0x224 PLL2 audio Bias config */
> + u32 pll3_bias_cfg; /* 0x228 PLL3 video Bias config */
> + u32 pll4_bias_cfg; /* 0x22c PLL4 ve Bias config */
> + u32 pll5_bias_cfg; /* 0x230 PLL5 ddr Bias config */
> + u32 pll6_bias_cfg; /* 0x234 PLL6 periph Bias config */
> + u32 pll1_c1_bias_cfg; /* 0x238 PLL1 c1cpu# Bias config */
> + u32 pll8_bias_cfg; /* 0x23c PLL7 Bias config */
> + u32 reserved25; /* 0x240 */
> + u32 pll9_bias_cfg; /* 0x244 PLL9 hsic Bias config */
> + u32 de_bias_cfg; /* 0x248 display engine Bias config */
> + u32 video1_bias_cfg; /* 0x24c pll video1 bias register */
> + u32 c0_tuning_cfg; /* 0x250 pll c0cpu# tuning register */
> + u32 c1_tuning_cfg; /* 0x254 pll c1cpu# tuning register */
> + u32 reserved26[11]; /* 0x258 */
> + u32 pll2_pattern_cfg0; /* 0x284 PLL2 Pattern register 0 */
> + u32 pll3_pattern_cfg0; /* 0x288 PLL3 Pattern register 0 */
> + u32 reserved27; /* 0x28c */
> + u32 pll5_pattern_cfg0; /* 0x290 PLL5 Pattern register 0*/
> + u32 reserved28[4]; /* 0x294 */
> + u32 pll2_pattern_cfg1; /* 0x2a4 PLL2 Pattern register 1 */
> + u32 pll3_pattern_cfg1; /* 0x2a8 PLL3 Pattern register 1 */
> + u32 reserved29; /* 0x2ac */
> + u32 pll5_pattern_cfg1; /* 0x2b0 PLL5 Pattern register 1 */
> + u32 reserved30[3]; /* 0x2b4 */
> + u32 ahb_reset0_cfg; /* 0x2c0 AHB1 Reset 0 config */
> + u32 ahb_reset1_cfg; /* 0x2c4 AHB1 Reset 1 config */
> + u32 ahb_reset2_cfg; /* 0x2c8 AHB1 Reset 2 config */
> + u32 reserved31;
> + u32 ahb_reset3_cfg; /* 0x2d0 AHB1 Reset 3 config */
> + u32 reserved32; /* 0x2d4 */
> + u32 apb2_reset_cfg; /* 0x2d8 BUS Reset 4 config */
> +};
> +
> +/* apb2 bit field */
> +#define APB2_CLK_SRC_LOSC (0x0 << 24)
> +#define APB2_CLK_SRC_OSC24M (0x1 << 24)
> +#define APB2_CLK_SRC_PLL6 (0x2 << 24)
> +#define APB2_CLK_SRC_MASK (0x3 << 24)
> +#define APB2_CLK_RATE_N_1 (0x0 << 16)
> +#define APB2_CLK_RATE_N_2 (0x1 << 16)
> +#define APB2_CLK_RATE_N_4 (0x2 << 16)
> +#define APB2_CLK_RATE_N_8 (0x3 << 16)
> +#define APB2_CLK_RATE_N_MASK (3 << 16)
> +#define APB2_CLK_RATE_M(m) (((m)-1) << 0)
> +#define APB2_CLK_RATE_M_MASK (0x1f << 0)
> +
> +/* apb2 gate field */
> +#define APB2_GATE_UART_SHIFT (16)
> +#define APB2_GATE_UART_MASK (0xff << APB2_GATE_UART_SHIFT)
> +#define APB2_GATE_TWI_SHIFT (0)
> +#define APB2_GATE_TWI_MASK (0xf << APB2_GATE_TWI_SHIFT)
> +
> +/* cpu_axi_cfg bits */
> +#define AXI0_DIV_SHIFT 0
> +#define AXI1_DIV_SHIFT 16
> +#define C0_CPUX_CLK_SRC_SHIFT 12
> +#define C1_CPUX_CLK_SRC_SHIFT 28
> +
> +#define AXI_DIV_1 0
> +#define AXI_DIV_2 1
> +#define AXI_DIV_3 2
> +#define AXI_DIV_4 3
> +#define CPU_CLK_SRC_OSC24M 0
> +#define CPU_CLK_SRC_PLL1 1
> +
> +#define CCM_PLL1_CTRL_N(n) ((((n) - 1) & 0xff) << 8)
> +#define CCM_PLL1_CTRL_P(n) (((n) & 0x1) << 16)
> +#define CCM_PLL1_CTRL_EN (0x1 << 31)
> +#define CMM_PLL1_CLOCK_TIME_2 (0x2 << 24)
> +
> +#define PLL8_CFG_DEFAULT 0x42800
> +#define CCM_CCI400_CLK_SEL_HSIC (0x2<<24)
> +
> +#define CCM_PLL5_DIV1_SHIFT 16
> +#define CCM_PLL5_DIV2_SHIFT 18
> +#define CCM_PLL5_CTRL_N(n) (((n) - 1) << 8)
> +#define CCM_PLL5_CTRL_UPD (0x1 << 30)
> +#define CCM_PLL5_CTRL_EN (0x1 << 31)
> +
> +#define PLL6_CFG_DEFAULT 0x80041800 /* 576 MHz */
> +#define CCM_PLL6_CTRL_N_SHIFT 8
> +#define CCM_PLL6_CTRL_N_MASK (0xff << CCM_PLL6_CTRL_N_SHIFT)
> +#define CCM_PLL6_CTRL_DIV1_SHIFT 16
> +#define CCM_PLL6_CTRL_DIV1_MASK (0x1 << CCM_PLL6_CTRL_DIV1_SHIFT)
> +#define CCM_PLL6_CTRL_DIV2_SHIFT 18
> +#define CCM_PLL6_CTRL_DIV2_MASK (0x1 << CCM_PLL6_CTRL_DIV2_SHIFT)
> +
> +#define AHB1_ABP1_DIV_DEFAULT 0x00002190
> +#define AHB1_CLK_SRC_MASK (0x3<<12)
> +#define AHB1_CLK_SRC_INTOSC (0x0<<12)
> +#define AHB1_CLK_SRC_OSC24M (0x1<<12)
> +#define AHB1_CLK_SRC_PLL6 (0x2<<12)
> +
> +#define AXI_GATE_OFFSET_DRAM 0
> +
> +/* ahb_gate0 offsets */
> +#define AHB_GATE_OFFSET_USB_OHCI1 30
> +#define AHB_GATE_OFFSET_USB_OHCI0 29
> +#define AHB_GATE_OFFSET_USB_EHCI1 27
> +#define AHB_GATE_OFFSET_USB_EHCI0 26
> +#define AHB_GATE_OFFSET_USB0 24
> +#define AHB_GATE_OFFSET_SPI1 21
> +#define AHB_GATE_OFFSET_SPI0 20
> +#define AHB_GATE_OFFSET_HSTIMER 19
> +#define AHB_GATE_OFFSET_EMAC 17
> +#define AHB_GATE_OFFSET_MCTL 14
> +#define AHB_GATE_OFFSET_GMAC 17
> +#define AHB_GATE_OFFSET_NAND0 13
> +#define AHB_GATE_OFFSET_MMC0 8
> +#define AHB_GATE_OFFSET_MMC(n) (AHB_GATE_OFFSET_MMC0 + (n))
> +#define AHB_GATE_OFFSET_DMA 6
> +#define AHB_GATE_OFFSET_SS 5
> +
> +/* ahb_gate1 offsets */
> +#define AHB_GATE_OFFSET_DRC0 25
> +#define AHB_GATE_OFFSET_DE_FE0 14
> +#define AHB_GATE_OFFSET_DE_BE0 12
> +#define AHB_GATE_OFFSET_HDMI 11
> +#define AHB_GATE_OFFSET_LCD1 5
> +#define AHB_GATE_OFFSET_LCD0 4
> +
> +#define CCM_MMC_CTRL_M(x) ((x) - 1)
> +#define CCM_MMC_CTRL_OCLK_DLY(x) ((x) << 8)
> +#define CCM_MMC_CTRL_N(x) ((x) << 16)
> +#define CCM_MMC_CTRL_SCLK_DLY(x) ((x) << 20)
> +#define CCM_MMC_CTRL_OSCM24 (0x0 << 24)
> +#define CCM_MMC_CTRL_PLL6 (0x1 << 24)
> +#define CCM_MMC_CTRL_ENABLE (0x1 << 31)
> +
> +#define CCM_USB_CTRL_PHY0_RST (0x1 << 0)
> +#define CCM_USB_CTRL_PHY1_RST (0x1 << 1)
> +#define CCM_USB_CTRL_PHY2_RST (0x1 << 2)
> +/* There is no global phy clk gate on sun6i, define as 0 */
> +#define CCM_USB_CTRL_PHYGATE 0
> +#define CCM_USB_CTRL_PHY0_CLK (0x1 << 8)
> +#define CCM_USB_CTRL_PHY1_CLK (0x1 << 9)
> +#define CCM_USB_CTRL_PHY2_CLK (0x1 << 10)
> +#define CCM_USB_CTRL_OHCI0_CLK (0x1 << 16)
> +#define CCM_USB_CTRL_OHCI1_CLK (0x1 << 17)
> +
> +#define CCM_GMAC_CTRL_TX_CLK_SRC_MII 0x0
> +#define CCM_GMAC_CTRL_TX_CLK_SRC_EXT_RGMII 0x1
> +#define CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII 0x2
> +#define CCM_GMAC_CTRL_GPIT_MII (0x0 << 2)
> +#define CCM_GMAC_CTRL_GPIT_RGMII (0x1 << 2)
> +#define CCM_GMAC_CTRL_RX_CLK_DELAY(x) ((x) << 5)
> +#define CCM_GMAC_CTRL_TX_CLK_DELAY(x) ((x) << 10)
> +
> +#define MDFS_CLK_DEFAULT 0x81000002 /* PLL6 / 3 */
> +
> +#define CCM_DRAMCLK_CFG_DIV(x) ((x - 1) << 0)
> +#define CCM_DRAMCLK_CFG_DIV_MASK (0xf << 0)
> +#define CCM_DRAMCLK_CFG_DIV0(x) ((x - 1) << 8)
> +#define CCM_DRAMCLK_CFG_DIV0_MASK (0xf << 8)
> +#define CCM_DRAMCLK_CFG_UPD (0x1 << 16)
> +#define CCM_DRAMCLK_CFG_RST (0x1 << 31)
> +
> +#define CCM_DRAMPLL_CFG_SRC_PLL5 (0x0 << 16) /* Select PLL5 (DDR0) */
> +#define CCM_DRAMPLL_CFG_SRC_PLL11 (0x1 << 16) /* Select PLL11 (DDR1) */
> +#define CCM_DRAMPLL_CFG_SRC_MASK (0x1 << 16)
> +
> +#define CCM_MBUS_RESET_RESET (0x1 << 31)
> +
> +#define CCM_DRAM_GATE_OFFSET_DE_FE0 24
> +#define CCM_DRAM_GATE_OFFSET_DE_FE1 25
> +#define CCM_DRAM_GATE_OFFSET_DE_BE0 26
> +#define CCM_DRAM_GATE_OFFSET_DE_BE1 27
> +
> +
> +#define MBUS_CLK_DEFAULT 0x81000002 /* PLL6 / 2 */
> +
> +#define MBUS_CLK_GATE (0x1 << 31)
> +
> +/* ahb_reset0 offsets */
> +#define AHB_RESET_OFFSET_GMAC 17
> +#define AHB_RESET_OFFSET_MCTL 14
> +#define AHB_RESET_OFFSET_MMC3 11
> +#define AHB_RESET_OFFSET_MMC2 10
> +#define AHB_RESET_OFFSET_MMC1 9
> +#define AHB_RESET_OFFSET_MMC0 8
> +#define AHB_RESET_OFFSET_MMC(n) (AHB_RESET_OFFSET_MMC0 + (n))
> +#define AHB_RESET_OFFSET_SS 5
> +
> +/* ahb_reset1 offsets */
> +#define AHB_RESET_OFFSET_SAT 26
> +#define AHB_RESET_OFFSET_DRC0 25
> +#define AHB_RESET_OFFSET_DE_FE0 14
> +#define AHB_RESET_OFFSET_DE_BE0 12
> +#define AHB_RESET_OFFSET_HDMI 11
> +#define AHB_RESET_OFFSET_LCD1 5
> +#define AHB_RESET_OFFSET_LCD0 4
> +
> +/* ahb_reset2 offsets */
> +#define AHB_RESET_OFFSET_LVDS 0
> +
> +/* apb2 reset */
> +#define APB2_RESET_UART_SHIFT (16)
> +#define APB2_RESET_UART_MASK (0xff << APB2_RESET_UART_SHIFT)
> +#define APB2_RESET_TWI_SHIFT (0)
> +#define APB2_RESET_TWI_MASK (0xf << APB2_RESET_TWI_SHIFT)
> +
> +
> +#ifndef __ASSEMBLY__
> +void clock_set_pll1(unsigned int hz);
> +void clock_set_pll5(unsigned int clk);
> +unsigned int clock_get_pll6(void);
> +#endif
> +
> +#endif /* _SUNXI_CLOCK_SUN8I_A83T_H */
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 07/10] sunxi: Add support for Allwinner A83T DRAM
2015-11-12 18:09 ` [U-Boot] [PATCH 07/10] sunxi: Add support for Allwinner A83T DRAM Vishnu Patekar
@ 2015-11-13 17:25 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:25 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Add support for A83T dram. Register are different from sun8i A33.
> init code is similar to A33 dram init.
> hope we'll shift duplicate code in dram_sun8i_*
> to dram helper in future.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
This one looks good as is.
Regards,
Hans
> ---
> arch/arm/cpu/armv7/sunxi/Makefile | 2 +
> arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424 ++++++++++++++++++++++
> arch/arm/include/asm/arch-sunxi/dram.h | 2 +
> arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++
> 4 files changed, 629 insertions(+)
> create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
> create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
>
> diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
> index 3c9fed3..c558016 100644
> --- a/arch/arm/cpu/armv7/sunxi/Makefile
> +++ b/arch/arm/cpu/armv7/sunxi/Makefile
> @@ -54,5 +54,7 @@ obj-$(CONFIG_MACH_SUN6I) += dram_sun6i.o
> obj-$(CONFIG_MACH_SUN7I) += dram_sun4i.o
> obj-$(CONFIG_MACH_SUN8I_A23) += dram_sun8i_a23.o
> obj-$(CONFIG_MACH_SUN8I_A33) += dram_sun8i_a33.o
> +obj-$(CONFIG_MACH_SUN8I_A83T) += dram_sun8i_a83t.o
> +
> obj-y += fel_utils.o
> endif
> diff --git a/arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
> new file mode 100644
> index 0000000..d757e40
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
> @@ -0,0 +1,424 @@
> +/*
> + * Sun8i a33 platform dram controller init.
> + *
> + * (C) Copyright 2007-2015 Allwinner Technology Co.
> + * Jerry Wang <wangflord@allwinnertech.com>
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
> + * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +#include <common.h>
> +#include <errno.h>
> +#include <asm/io.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/dram.h>
> +#include <asm/arch/prcm.h>
> +
> +#define DRAM_CLK_MUL 2
> +#define DRAM_CLK_DIV 1
> +
> +struct dram_para {
> + u8 cs1;
> + u8 seq;
> + u8 bank;
> + u8 rank;
> + u8 rows;
> + u8 bus_width;
> + u16 page_size;
> +};
> +
> +static void mctl_set_cr(struct dram_para *para)
> +{
> + struct sunxi_mctl_com_reg * const mctl_com =
> + (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
> +
> + writel(MCTL_CR_CS1_CONTROL(para->cs1) | MCTL_CR_UNKNOWN |
> + MCTL_CR_CHANNEL(1) | MCTL_CR_DDR3 |
> + (para->seq ? MCTL_CR_SEQUENCE : 0) |
> + ((para->bus_width == 16) ? MCTL_CR_BUSW16 : MCTL_CR_BUSW8) |
> + MCTL_CR_PAGE_SIZE(para->page_size) | MCTL_CR_ROW(para->rows) |
> + MCTL_CR_BANK(para->bank) | MCTL_CR_RANK(para->rank),
> + &mctl_com->cr);
> +}
> +
> +static void auto_detect_dram_size(struct dram_para *para)
> +{
> + u8 orig_rank = para->rank;
> + int rows, columns;
> +
> + /* Row detect */
> + para->page_size = 512;
> + para->seq = 1;
> + para->rows = 16;
> + para->rank = 1;
> + mctl_set_cr(para);
> + for (rows = 11 ; rows < 16 ; rows++) {
> + if (mctl_mem_matches(1 << (rows + 9))) /* row-column */
> + break;
> + }
> +
> + /* Column (page size) detect */
> + para->rows = 11;
> + para->page_size = 8192;
> + mctl_set_cr(para);
> + for (columns = 9 ; columns < 13 ; columns++) {
> + if (mctl_mem_matches(1 << columns))
> + break;
> + }
> +
> + para->seq = 0;
> + para->rank = orig_rank;
> + para->rows = rows;
> + para->page_size = 1 << columns;
> + mctl_set_cr(para);
> +}
> +
> +static inline int ns_to_t(int nanoseconds)
> +{
> + const unsigned int ctrl_freq =
> + CONFIG_DRAM_CLK * DRAM_CLK_MUL / DRAM_CLK_DIV;
> +
> + return (ctrl_freq * nanoseconds + 999) / 1000;
> +}
> +
> +static void auto_set_timing_para(struct dram_para *para)
> +{
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> + u32 reg_val;
> +
> + u8 tccd = 2;
> + u8 tfaw = ns_to_t(50);
> + u8 trrd = max(ns_to_t(10), 4);
> + u8 trcd = ns_to_t(15);
> + u8 trc = ns_to_t(53);
> + u8 txp = max(ns_to_t(8), 3);
> + u8 twtr = max(ns_to_t(8), 4);
> + u8 trtp = max(ns_to_t(8), 4);
> + u8 twr = max(ns_to_t(15), 3);
> + u8 trp = ns_to_t(15);
> + u8 tras = ns_to_t(38);
> +
> + u16 trefi = ns_to_t(7800) / 32;
> + u16 trfc = ns_to_t(350);
> +
> + /* Fixed timing parameters */
> + u8 tmrw = 0;
> + u8 tmrd = 4;
> + u8 tmod = 12;
> + u8 tcke = 3;
> + u8 tcksrx = 5;
> + u8 tcksre = 5;
> + u8 tckesr = 4;
> + u8 trasmax = 24;
> + u8 tcl = 6; /* CL 12 */
> + u8 tcwl = 4; /* CWL 8 */
> + u8 t_rdata_en = 4;
> + u8 wr_latency = 2;
> +
> + u32 tdinit0 = (500 * CONFIG_DRAM_CLK) + 1; /* 500us */
> + u32 tdinit1 = (360 * CONFIG_DRAM_CLK) / 1000 + 1; /* 360ns */
> + u32 tdinit2 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */
> + u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */
> +
> + u8 twtp = tcwl + 2 + twr; /* WL + BL / 2 + tWR */
> + u8 twr2rd = tcwl + 2 + twtr; /* WL + BL / 2 + tWTR */
> + u8 trd2wr = tcl + 2 + 1 - tcwl; /* RL + BL / 2 + 2 - WL */
> +
> + /* Set work mode register */
> + mctl_set_cr(para);
> + /* Set mode register */
> + writel(MCTL_MR0, &mctl_ctl->mr0);
> + writel(MCTL_MR1, &mctl_ctl->mr1);
> + writel(MCTL_MR2, &mctl_ctl->mr2);
> + writel(MCTL_MR3, &mctl_ctl->mr3);
> + /* Set dram timing */
> + reg_val = (twtp << 24) | (tfaw << 16) | (trasmax << 8) | (tras << 0);
> + writel(reg_val, &mctl_ctl->dramtmg0);
> + reg_val = (txp << 16) | (trtp << 8) | (trc << 0);
> + writel(reg_val, &mctl_ctl->dramtmg1);
> + reg_val = (tcwl << 24) | (tcl << 16) | (trd2wr << 8) | (twr2rd << 0);
> + writel(reg_val, &mctl_ctl->dramtmg2);
> + reg_val = (tmrw << 16) | (tmrd << 12) | (tmod << 0);
> + writel(reg_val, &mctl_ctl->dramtmg3);
> + reg_val = (trcd << 24) | (tccd << 16) | (trrd << 8) | (trp << 0);
> + writel(reg_val, &mctl_ctl->dramtmg4);
> + reg_val = (tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | (tcke << 0);
> + writel(reg_val, &mctl_ctl->dramtmg5);
> + /* Set two rank timing and exit self-refresh timing */
> + reg_val = readl(&mctl_ctl->dramtmg8);
> + reg_val &= ~(0xff << 8);
> + reg_val &= ~(0xff << 0);
> + reg_val |= (0x33 << 8);
> + reg_val |= (0x8 << 0);
> + writel(reg_val, &mctl_ctl->dramtmg8);
> + /* Set phy interface time */
> + reg_val = (0x2 << 24) | (t_rdata_en << 16) | (0x1 << 8)
> + | (wr_latency << 0);
> + /* PHY interface write latency and read latency configure */
> + writel(reg_val, &mctl_ctl->pitmg0);
> + /* Set phy time PTR0-2 use default */
> + writel(((tdinit0 << 0) | (tdinit1 << 20)), &mctl_ctl->ptr3);
> + writel(((tdinit2 << 0) | (tdinit3 << 20)), &mctl_ctl->ptr4);
> + /* Set refresh timing */
> + reg_val = (trefi << 16) | (trfc << 0);
> + writel(reg_val, &mctl_ctl->rfshtmg);
> +}
> +
> +static void mctl_set_pir(u32 val)
> +{
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> +
> + writel(val, &mctl_ctl->pir);
> + mctl_await_completion(&mctl_ctl->pgsr0, 0x1, 0x1);
> +}
> +
> +static void mctl_data_train_cfg(struct dram_para *para)
> +{
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> +
> + if (para->rank == 2)
> + clrsetbits_le32(&mctl_ctl->dtcr, 0x3 << 24, 0x3 << 24);
> + else
> + clrsetbits_le32(&mctl_ctl->dtcr, 0x3 << 24, 0x1 << 24);
> +}
> +
> +static int mctl_train_dram(struct dram_para *para)
> +{
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> +
> + mctl_data_train_cfg(para);
> + mctl_set_pir(0x5f3);
> +
> + return ((readl(&mctl_ctl->pgsr0) >> 20) & 0xff) ? -EIO : 0;
> +}
> +
> +static void set_master_priority(void)
> +{
> + writel(0x00a0000d, MCTL_MASTER_CFG0(0));
> + writel(0x00500064, MCTL_MASTER_CFG1(0));
> + writel(0x07000009, MCTL_MASTER_CFG0(1));
> + writel(0x00000600, MCTL_MASTER_CFG1(1));
> + writel(0x01000009, MCTL_MASTER_CFG0(3));
> + writel(0x00000064, MCTL_MASTER_CFG1(3));
> + writel(0x08000009, MCTL_MASTER_CFG0(4));
> + writel(0x00000640, MCTL_MASTER_CFG1(4));
> + writel(0x20000308, MCTL_MASTER_CFG0(8));
> + writel(0x00001000, MCTL_MASTER_CFG1(8));
> + writel(0x02800009, MCTL_MASTER_CFG0(9));
> + writel(0x00000100, MCTL_MASTER_CFG1(9));
> + writel(0x01800009, MCTL_MASTER_CFG0(5));
> + writel(0x00000100, MCTL_MASTER_CFG1(5));
> + writel(0x01800009, MCTL_MASTER_CFG0(7));
> + writel(0x00000100, MCTL_MASTER_CFG1(7));
> + writel(0x00640009, MCTL_MASTER_CFG0(6));
> + writel(0x00000032, MCTL_MASTER_CFG1(6));
> + writel(0x0100000d, MCTL_MASTER_CFG0(2));
> + writel(0x00500080, MCTL_MASTER_CFG1(2));
> +}
> +
> +static int mctl_channel_init(struct dram_para *para)
> +{
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> + struct sunxi_mctl_com_reg * const mctl_com =
> + (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
> + u32 low_data_lines_status; /* Training status of datalines 0 - 7 */
> + u32 high_data_lines_status; /* Training status of datalines 8 - 15 */
> + u32 i, rval;
> +
> + auto_set_timing_para(para);
> +
> + /* Set dram master access priority */
> + writel(0x000101a0, &mctl_com->bwcr);
> + /* set cpu high priority */
> + writel(0x1, &mctl_com->mapr);
> + set_master_priority();
> + udelay(250);
> +
> + /* Disable dram VTC */
> + clrbits_le32(&mctl_ctl->pgcr0, 0x3f << 0 | 0x1 << 30);
> + clrsetbits_le32(&mctl_ctl->pgcr1, 0x1 << 24, 0x1 << 26);
> +
> + writel(0x94be6fa3, MCTL_PROTECT);
> + udelay(100);
> + clrsetbits_le32(MX_UPD2, 0xfff << 16, 0x50 << 26);
> + writel(0x0, MCTL_PROTECT);
> + udelay(100);
> +
> +
> + /* Set ODT */
> + if (IS_ENABLED(CONFIG_DRAM_ODT_EN))
> + rval = 0x0;
> + else
> + rval = 0x2;
> +
> + for (i = 0 ; i < 11 ; i++) {
> + clrsetbits_le32(DATX0IOCR(i), (0x3 << 24) | (0x3 << 16),
> + rval << 24);
> + clrsetbits_le32(DATX1IOCR(i), (0x3 << 24) | (0x3 << 16),
> + rval << 24);
> + clrsetbits_le32(DATX2IOCR(i), (0x3 << 24) | (0x3 << 16),
> + rval << 24);
> + clrsetbits_le32(DATX3IOCR(i), (0x3 << 24) | (0x3 << 16),
> + rval << 24);
> + }
> +
> + for (i = 0; i < 31; i++)
> + clrsetbits_le32(CAIOCR(i), 0x3 << 26 | 0x3 << 16, 0x2 << 26);
> +
> + /* set PLL configuration */
> + if (CONFIG_DRAM_CLK >= 480)
> + setbits_le32(&mctl_ctl->pllgcr, 0x1 << 19);
> + else
> + setbits_le32(&mctl_ctl->pllgcr, 0x3 << 19);
> +
> + /* Auto detect dram config, set 2 rank and 16bit bus-width */
> + para->cs1 = 0;
> + para->rank = 2;
> + para->bus_width = 16;
> + mctl_set_cr(para);
> +
> + /* Open DQS gating */
> + clrbits_le32(&mctl_ctl->pgcr2, (0x3 << 6));
> + clrbits_le32(&mctl_ctl->dqsgmr, (0x1 << 8) | (0x7));
> +
> + if (readl(&mctl_com->cr) & 0x1)
> + writel(0x00000303, &mctl_ctl->odtmap);
> + else
> + writel(0x00000201, &mctl_ctl->odtmap);
> +
> + mctl_data_train_cfg(para);
> + /* ZQ calibration */
> + clrsetbits_le32(ZQnPR(0), 0x000000ff, CONFIG_DRAM_ZQ & 0xff);
> + clrsetbits_le32(ZQnPR(1), 0x000000ff, (CONFIG_DRAM_ZQ >> 8) & 0xff);
> + /* CA calibration */
> + mctl_set_pir(0x0201f3 | 0x1<<10);
> +
> + /* DQS gate training */
> + if (mctl_train_dram(para) != 0) {
> + low_data_lines_status = (readl(DXnGSR0(0)) >> 24) & 0x03;
> + high_data_lines_status = (readl(DXnGSR0(1)) >> 24) & 0x03;
> +
> + if (low_data_lines_status == 0x3)
> + return -EIO;
> +
> + /* DRAM has only one rank */
> + para->rank = 1;
> + mctl_set_cr(para);
> +
> + if (low_data_lines_status == high_data_lines_status)
> + goto done; /* 16 bit bus, 1 rank */
> +
> + if (!(low_data_lines_status & high_data_lines_status)) {
> + /* Retry 16 bit bus-width with CS1 set */
> + para->cs1 = 1;
> + mctl_set_cr(para);
> + if (mctl_train_dram(para) == 0)
> + goto done;
> + }
> +
> + /* Try 8 bit bus-width */
> + writel(0x0, DXnGCR0(1)); /* Disable high DQ */
> + para->cs1 = 0;
> + para->bus_width = 8;
> + mctl_set_cr(para);
> + if (mctl_train_dram(para) != 0)
> + return -EIO;
> + }
> +done:
> + /* Check the dramc status */
> + mctl_await_completion(&mctl_ctl->statr, 0x1, 0x1);
> +
> + /* Close DQS gating */
> + setbits_le32(&mctl_ctl->pgcr2, 0x3 << 6);
> +
> + /* set PGCR3,CKE polarity */
> + writel(0x00aa0060, &mctl_ctl->pgcr3);
> + /* Enable master access */
> + writel(0xffffffff, &mctl_com->maer);
> +
> + return 0;
> +}
> +
> +static void mctl_sys_init(struct dram_para *para)
> +{
> + struct sunxi_ccm_reg * const ccm =
> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> +
> + clrbits_le32(&ccm->mbus_clk_cfg, MBUS_CLK_GATE);
> + clrbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
> + clrbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
> + clrbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
> + clrbits_le32(&ccm->pll5_cfg, CCM_PLL5_CTRL_EN);
> + clrbits_le32(&ccm->dram_clk_cfg, 0x01<<31);
> +
> + clock_set_pll5(CONFIG_DRAM_CLK * 1000000 * DRAM_CLK_MUL);
> +
> + clrsetbits_le32(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_DIV_MASK,
> + CCM_DRAMCLK_CFG_DIV(DRAM_CLK_DIV) |
> + CCM_DRAMCLK_CFG_RST | CCM_DRAMCLK_CFG_UPD);
> + mctl_await_completion(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_UPD, 0);
> +
> + setbits_le32(&ccm->ahb_reset0_cfg, 1 << 14);
> + setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
> + setbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
> + setbits_le32(&ccm->mbus_clk_cfg, MBUS_CLK_GATE);
> +
> + setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
> + setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
> + setbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
> + setbits_le32(&ccm->mbus_clk_cfg, MBUS_CLK_GATE);
> +
> + /* Set dram master access priority */
> + writel(0x0000e00f, &mctl_ctl->clken); /* normal */
> +
> + udelay(250);
> +}
> +
> +unsigned long sunxi_dram_init(void)
> +{
> + struct sunxi_mctl_com_reg * const mctl_com =
> + (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
> + struct sunxi_mctl_ctl_reg * const mctl_ctl =
> + (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
> +
> + struct dram_para para = {
> + .cs1 = 0,
> + .bank = 1,
> + .rank = 1,
> + .rows = 15,
> + .bus_width = 16,
> + .page_size = 2048,
> + };
> +
> + setbits_le32(SUNXI_PRCM_BASE + 0x1e0, 0x1 << 8);
> +
> + writel(0, (SUNXI_PRCM_BASE + 0x1e8));
> + udelay(10);
> +
> + mctl_sys_init(¶);
> +
> + if (mctl_channel_init(¶) != 0)
> + return 0;
> +
> + auto_detect_dram_size(¶);
> +
> + /* Enable master software clk */
> + writel(readl(&mctl_com->swonr) | 0x3ffff, &mctl_com->swonr);
> +
> + /* Set DRAM ODT MAP */
> + if (para.rank == 2)
> + writel(0x00000303, &mctl_ctl->odtmap);
> + else
> + writel(0x00000201, &mctl_ctl->odtmap);
> +
> + return para.page_size * (para.bus_width / 8) *
> + (1 << (para.bank + para.rank + para.rows));
> +}
> diff --git a/arch/arm/include/asm/arch-sunxi/dram.h b/arch/arm/include/asm/arch-sunxi/dram.h
> index 273f80f..bfe06a8 100644
> --- a/arch/arm/include/asm/arch-sunxi/dram.h
> +++ b/arch/arm/include/asm/arch-sunxi/dram.h
> @@ -22,6 +22,8 @@
> #include <asm/arch/dram_sun8i_a23.h>
> #elif defined(CONFIG_MACH_SUN8I_A33)
> #include <asm/arch/dram_sun8i_a33.h>
> +#elif defined(CONFIG_MACH_SUN8I_A83T)
> +#include <asm/arch/dram_sun8i_a83t.h>
> #else
> #include <asm/arch/dram_sun4i.h>
> #endif
> diff --git a/arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h b/arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
> new file mode 100644
> index 0000000..2891b71
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
> @@ -0,0 +1,201 @@
> +/*
> + * Sun8i platform dram controller register and constant defines
> + *
> + * (C) Copyright 2007-2015 Allwinner Technology Co.
> + * Jerry Wang <wangflord@allwinnertech.com>
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
> + * (C) Copyright 2014-2015 Hans de Goede <hdegoede@redhat.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef _SUNXI_DRAM_SUN8I_A83T_H
> +#define _SUNXI_DRAM_SUN8I_A83T_H
> +
> +struct sunxi_mctl_com_reg {
> + u32 cr; /* 0x00 */
> + u32 ccr; /* 0x04 controller configuration register */
> + u32 dbgcr; /* 0x08 */
> + u8 res0[0x4]; /* 0x0c */
> + u32 mcr0_0; /* 0x10 */
> + u32 mcr1_0; /* 0x14 */
> + u32 mcr0_1; /* 0x18 */
> + u32 mcr1_1; /* 0x1c */
> + u32 mcr0_2; /* 0x20 */
> + u32 mcr1_2; /* 0x24 */
> + u32 mcr0_3; /* 0x28 */
> + u32 mcr1_3; /* 0x2c */
> + u32 mcr0_4; /* 0x30 */
> + u32 mcr1_4; /* 0x34 */
> + u32 mcr0_5; /* 0x38 */
> + u32 mcr1_5; /* 0x3c */
> + u32 mcr0_6; /* 0x40 */
> + u32 mcr1_6; /* 0x44 */
> + u32 mcr0_7; /* 0x48 */
> + u32 mcr1_7; /* 0x4c */
> + u32 mcr0_8; /* 0x50 */
> + u32 mcr1_8; /* 0x54 */
> + u32 mcr0_9; /* 0x58 */
> + u32 mcr1_9; /* 0x5c */
> + u32 mcr0_10; /* 0x60 */
> + u32 mcr1_10; /* 0x64 */
> + u32 mcr0_11; /* 0x68 */
> + u32 mcr1_11; /* 0x6c */
> + u32 mcr0_12; /* 0x70 */
> + u32 mcr1_12; /* 0x74 */
> + u32 mcr0_13; /* 0x78 */
> + u32 mcr1_13; /* 0x7c */
> + u32 mcr0_14; /* 0x80 */
> + u32 mcr1_14; /* 0x84 */
> + u32 mcr0_15; /* 0x88 */
> + u32 mcr1_15; /* 0x8c */
> + u32 bwcr; /* 0x90 */
> + u32 maer; /* 0x94 */
> + u32 mapr; /* 0x98 */
> + u32 mcgcr; /* 0x9c */
> + u32 bwctr; /* 0xa0 */
> + u8 res2[0x8]; /* 0xa4 */
> + u32 swoffr; /* 0xac */
> + u8 res3[0x10]; /* 0xb0 */
> + u32 swonr; /* 0xc0 */
> + u8 res4[0x3c]; /* 0xc4 */
> + u32 mdfscr; /* 0x100 */
> + u32 mdfsmer; /* 0x104 */
> +};
> +
> +struct sunxi_mctl_ctl_reg {
> + u32 pir; /* 0x00 */
> + u32 pwrctl; /* 0x04 */
> + u32 mrctrl0; /* 0x08 */
> + u32 clken; /* 0x0c */
> + u32 pgsr0; /* 0x10 */
> + u32 pgsr1; /* 0x14 */
> + u32 statr; /* 0x18 */
> + u8 res1[0x14]; /* 0x1c */
> + u32 mr0; /* 0x30 */
> + u32 mr1; /* 0x34 */
> + u32 mr2; /* 0x38 */
> + u32 mr3; /* 0x3c */
> + u32 pllgcr; /* 0x40 */
> + u32 ptr0; /* 0x44 */
> + u32 ptr1; /* 0x48 */
> + u32 ptr2; /* 0x4c */
> + u32 ptr3; /* 0x50 */
> + u32 ptr4; /* 0x54 */
> + u32 dramtmg0; /* 0x58 dram timing parameters register 0 */
> + u32 dramtmg1; /* 0x5c dram timing parameters register 1 */
> + u32 dramtmg2; /* 0x60 dram timing parameters register 2 */
> + u32 dramtmg3; /* 0x64 dram timing parameters register 3 */
> + u32 dramtmg4; /* 0x68 dram timing parameters register 4 */
> + u32 dramtmg5; /* 0x6c dram timing parameters register 5 */
> + u32 dramtmg6; /* 0x70 dram timing parameters register 6 */
> + u32 dramtmg7; /* 0x74 dram timing parameters register 7 */
> + u32 dramtmg8; /* 0x78 dram timing parameters register 8 */
> + u32 odtcfg; /* 0x7c */
> + u32 pitmg0; /* 0x80 */
> + u32 pitmg1; /* 0x84 */
> + u8 res2[0x4]; /* 0x88 */
> + u32 rfshctl0; /* 0x8c */
> + u32 rfshtmg; /* 0x90 */
> + u32 rfshctl1; /* 0x94 */
> + u32 pwrtmg; /* 0x98 */
> + u8 res3[0x20]; /* 0x9c */
> + u32 dqsgmr; /* 0xbc */
> + u32 dtcr; /* 0xc0 */
> + u32 dtar0; /* 0xc4 */
> + u32 dtar1; /* 0xc8 */
> + u32 dtar2; /* 0xcc */
> + u32 dtar3; /* 0xd0 */
> + u32 dtdr0; /* 0xd4 */
> + u32 dtdr1; /* 0xd8 */
> + u32 dtmr0; /* 0xdc */
> + u32 dtmr1; /* 0xe0 */
> + u32 dtbmr; /* 0xe4 */
> + u32 catr0; /* 0xe8 */
> + u32 catr1; /* 0xec */
> + u32 dtedr0; /* 0xf0 */
> + u32 dtedr1; /* 0xf4 */
> + u8 res4[0x8]; /* 0xf8 */
> + u32 pgcr0; /* 0x100 */
> + u32 pgcr1; /* 0x104 */
> + u32 pgcr2; /* 0x108 */
> + u32 pgcr3; /* 0x10c */
> + u32 iovcr0; /* 0x110 */
> + u32 iovcr1; /* 0x114 */
> + u32 dqsdr; /* 0x118 */
> + u32 dxccr; /* 0x11c */
> + u32 odtmap; /* 0x120 */
> + u32 zqctl0; /* 0x124 */
> + u32 zqctl1; /* 0x128 */
> + u8 res6[0x14]; /* 0x12c */
> + u32 zqncr; /* 0x140 zq control register 0 */
> + u32 zqnpr; /* 0x144 zq control register 1 */
> + u32 zqndr; /* 0x148 zq control register 2 */
> + u32 zqnsr; /* 0x14c zq status register 0 */
> + u32 res7; /* 0x150 zq status register 1 */
> + u8 res8[0x6c]; /* 0x154 */
> + u32 sched; /* 0x1c0 */
> + u32 perfhpr0; /* 0x1c4 */
> + u32 perfhpr1; /* 0x1c8 */
> + u32 perflpr0; /* 0x1cc */
> + u32 perflpr1; /* 0x1d0 */
> + u32 perfwr0; /* 0x1d4 */
> + u32 perfwr1; /* 0x1d8 */
> +};
> +
> +
> +#define ZQnPR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000144 + 0x10 * x)
> +#define ZQnDR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000148 + 0x10 * x)
> +#define ZQnSR(x) (SUNXI_DRAM_CTL0_BASE + 0x0000014c + 0x10 * x)
> +
> +#define DXnGTR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000340 + 0x80 * x)
> +#define DXnGCR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000344 + 0x80 * x)
> +#define DXnGSR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000348 + 0x80 * x)
> +#define DXnGSR1(x) (SUNXI_DRAM_CTL0_BASE + 0x0000034c + 0x80 * x)
> +#define DXnGSR2(x) (SUNXI_DRAM_CTL0_BASE + 0x00000350 + 0x80 * x)
> +
> +#define CAIOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000210 + 0x4 * (x))
> +#define DXnMDLR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000300 + 0x80 * x)
> +#define DXMDLR0 (SUNXI_DRAM_CTL0_BASE + 0x00000300)
> +#define DXnLCDLR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000304 + 0x80 * x)
> +#define DXnLCDLR1(x) (SUNXI_DRAM_CTL0_BASE + 0x00000308 + 0x80 * x)
> +#define DXnLCDLR2(x) (SUNXI_DRAM_CTL0_BASE + 0x0000030c + 0x80 * x)
> +#define DATX0IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000310 + 0x4 * x)
> +#define DATX1IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000390 + 0x4 * x)
> +#define DATX2IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000410 + 0x4 * x)
> +#define DATX3IOCR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000490 + 0x4 * x)
> +#define MX_UPD0 (SUNXI_DRAM_CTL0_BASE + 0x00000880)
> +#define MX_UPD2 (SUNXI_DRAM_CTL0_BASE + 0x00000888)
> +
> +#define MCTL_PROTECT (SUNXI_DRAM_COM_BASE + 0x800)
> +#define MCTL_MASTER_CFG0(x) (SUNXI_DRAM_COM_BASE + 0x10 + 0x8 * x)
> +#define MCTL_MASTER_CFG1(x) (SUNXI_DRAM_COM_BASE + 0x14 + 0x8 * x)
> +
> +/*
> + * DRAM common (sunxi_mctl_com_reg) register constants.
> + */
> +#define MCTL_CR_RANK_MASK (3 << 0)
> +#define MCTL_CR_RANK(x) (((x) - 1) << 0)
> +#define MCTL_CR_BANK_MASK (3 << 2)
> +#define MCTL_CR_BANK(x) ((x) << 2)
> +#define MCTL_CR_ROW_MASK (0xf << 4)
> +#define MCTL_CR_ROW(x) (((x) - 1) << 4)
> +#define MCTL_CR_PAGE_SIZE_MASK (0xf << 8)
> +#define MCTL_CR_PAGE_SIZE(x) ((fls(x) - 4) << 8)
> +#define MCTL_CR_BUSW_MASK (7 << 12)
> +#define MCTL_CR_BUSW8 (0 << 12)
> +#define MCTL_CR_BUSW16 (1 << 12)
> +#define MCTL_CR_SEQUENCE (1 << 15)
> +#define MCTL_CR_DDR3 (3 << 16)
> +#define MCTL_CR_CHANNEL_MASK (1 << 19)
> +#define MCTL_CR_CHANNEL(x) (((x) - 1) << 19)
> +#define MCTL_CR_UNKNOWN (0x4 << 20)
> +#define MCTL_CR_CS1_CONTROL(x) ((x) << 24)
> +
> +/* DRAM control (sunxi_mctl_ctl_reg) register constants */
> +#define MCTL_MR0 0x1c70 /* CL=11, WR=12 */
> +#define MCTL_MR1 0x40
> +#define MCTL_MR2 0x18 /* CWL=8 */
> +#define MCTL_MR3 0x0
> +
> +#endif /* _SUNXI_DRAM_SUN8I_A83T_H */
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 08/10] sunxi: do not include display for A83T
2015-11-12 18:09 ` [U-Boot] [PATCH 08/10] sunxi: do not include display for A83T Vishnu Patekar
@ 2015-11-13 17:25 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:25 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Currently, there no display support for A83T.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Please merge this one into the "sunxi: Add Machine Support for A83T SOC"
commmit.
Regards,
Hans
> ---
> board/sunxi/Kconfig | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
> index ea69bf7..8dc3499 100644
> --- a/board/sunxi/Kconfig
> +++ b/board/sunxi/Kconfig
> @@ -376,6 +376,7 @@ config AXP_GPIO
>
> config VIDEO
> boolean "Enable graphical uboot console on HDMI, LCD or VGA"
> + depends on !MACH_SUN8I_A83T
> default y
> ---help---
> Say Y here to add support for using a cfb console on the HDMI, LCD
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 09/10] sunxi: dts: sun8i: Add Allwinner A83T dtsi
2015-11-12 18:09 ` [U-Boot] [PATCH 09/10] sunxi: dts: sun8i: Add Allwinner A83T dtsi Vishnu Patekar
@ 2015-11-13 17:26 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:26 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Allwinner A83T is new octa-core cortex-a7 SOC.
> This adds the basic dtsi, the clocks differs from
> earlier sun8i SOCs.
>
> This is not yet included in kernel.
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
> ---
> arch/arm/dts/sun8i-a83t.dtsi | 247 +++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 247 insertions(+)
> create mode 100644 arch/arm/dts/sun8i-a83t.dtsi
>
> diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi
> new file mode 100644
> index 0000000..da1b451
> --- /dev/null
> +++ b/arch/arm/dts/sun8i-a83t.dtsi
> @@ -0,0 +1,247 @@
> +/*
> + * Copyright 2015 Vishnu Patekar
> + *
> + * Vishnu Patekar <vishnupatekar0510@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> +
> + */
> +
> +#include "skeleton.dtsi"
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + chosen {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu at 0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu at 1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu at 2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu at 3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + cpu at 100 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <100>;
This must be reg = <0x100>;
> + };
> +
> + cpu at 101 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <101>;
Idem.
> + };
> + cpu at 102 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <102>;
Idem.
> + };
> +
> + cpu at 103 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <103>;
Idem.
Regards,
Hans
> + };
> + };
> +
> + memory {
> + reg = <0x40000000 0x80000000>;
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + clock-frequency = <24000000>;
> + arm,cpu-registers-not-fw-configured;
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + osc24M: osc24M_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "osc24M";
> + };
> +
> + osc32k: osc32k_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "osc32k";
> + };
> + };
> +
> + soc at 01c00000 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + gic: interrupt-controller at 01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x1000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + pio: pinctrl at 01c20800 {
> + compatible = "allwinner,sun8i-a83t-pinctrl";
> + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x01c20800 0x400>;
> + clocks = <&osc24M>;
> + gpio-controller;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + #gpio-cells = <3>;
> +
> + i2c0_pins_a: i2c0 at 0 {
> + allwinner,pins = "PH0", "PH1";
> + allwinner,function = "i2c0";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + i2c1_pins_a: i2c1 at 0 {
> + allwinner,pins = "PH2", "PH3";
> + allwinner,function = "i2c1";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + i2c2_pins_a: i2c2 at 0 {
> + allwinner,pins = "PH4", "PH5";
> + allwinner,function = "i2c2";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + mmc0_pins_a: mmc0 at 0 {
> + allwinner,pins = "PF0", "PF1", "PF2",
> + "PF3", "PF4", "PF5";
> + allwinner,function = "mmc0";
> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + mmc1_pins_a: mmc1 at 0 {
> + allwinner,pins = "PG0", "PG1", "PG2",
> + "PG3", "PG4", "PG5";
> + allwinner,function = "mmc1";
> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + mmc2_8bit_pins: mmc2_8bit {
> + allwinner,pins = "PC5", "PC6", "PC8",
> + "PC9", "PC10", "PC11",
> + "PC12", "PC13", "PC14",
> + "PC15";
> + allwinner,function = "mmc2";
> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + uart0_pins_a: uart0 at 0 {
> + allwinner,pins = "PF2", "PF4";
> + allwinner,function = "uart0";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + uart0_pins_b: uart0 at 1 {
> + allwinner,pins = "PB9", "PB10";
> + allwinner,function = "uart0";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> + };
> +
> + uart0: serial at 01c28000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28000 0x400>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&osc24M>;
> + status = "disabled";
> + };
> + };
> +};
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 10/10] sunxi: Add suport for A83T HomletV2 Board by Allwinner
2015-11-12 18:09 ` [U-Boot] [PATCH 10/10] sunxi: Add suport for A83T HomletV2 Board by Allwinner Vishnu Patekar
@ 2015-11-13 17:27 ` Hans de Goede
0 siblings, 0 replies; 28+ messages in thread
From: Hans de Goede @ 2015-11-13 17:27 UTC (permalink / raw)
To: u-boot
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> Add dts and defconfig for h8homletv2 board.
>
> H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
> It has UART, ethernet, USB, HDMI, etc ports on it.
>
> A83T patches are tested on this board.
>
> For FEL mode it needs USB A-A(Male) cable. I used uart0 which
> is multiplexed to microsd pins PF2 and PF4.
>
> Enabled UART0 Header(PB9, PB10 pins).
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
> ---
> arch/arm/dts/Makefile | 2 +
> arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 +++++++++++++++++++++++
> board/sunxi/MAINTAINERS | 5 ++
> configs/h8_homlet_v2_defconfig | 26 +++++++++
> 4 files changed, 97 insertions(+)
> create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
> create mode 100644 configs/h8_homlet_v2_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 8b656e9..d303eea 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -157,6 +157,8 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \
> sun8i-a33-ga10h-v1.1.dtb \
> sun8i-a33-q8-tablet.dtb \
> sun8i-a33-sinlinx-sina33.dtb
> +dtb-$(CONFIG_MACH_SUN8I_A83T) += \
> + sun8i-a83t-allwinner-h8homlet-v2.dtb
> dtb-$(CONFIG_MACH_SUN9I) += \
> sun9i-a80-optimus.dtb \
> sun9i-a80-cubieboard4.dtb
> diff --git a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
> new file mode 100644
> index 0000000..342e1d3
> --- /dev/null
> +++ b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
> @@ -0,0 +1,64 @@
> +/*
> + * Copyright 2015 Vishnu Patekar
> + * Vishnu Patekar <vishnupatekar0510@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-a83t.dtsi"
> +
> +/ {
> + model = "Allwinner A83T H8Homlet Proto Dev Board v2.0";
> + compatible = "allwinner,h8homlet-v2", "allwinner,sun8i-a83t";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_b>;
> + status = "okay";
> +};
> diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> index 96c4f3a..c0c2bdd 100644
> --- a/board/sunxi/MAINTAINERS
> +++ b/board/sunxi/MAINTAINERS
> @@ -99,6 +99,11 @@ M: Priit Laes <plaes@plaes.org>
> S: Maintained
> F: configs/sunxi_Gemei_G9_defconfig
>
> +H8HOMLET PROTO A83T BOARD
> +M: VishnuPatekar <vishnupatekar0510@gmail.com>
> +S: Maintained
> +F: configs/h8_homlet_v2_defconfig
> +
> HUMMINGBIRD-A31 BOARD
> M: Chen-Yu Tsai <wens@csie.org>
> S: Maintained
> diff --git a/configs/h8_homlet_v2_defconfig b/configs/h8_homlet_v2_defconfig
> new file mode 100644
> index 0000000..b78a240
> --- /dev/null
> +++ b/configs/h8_homlet_v2_defconfig
> @@ -0,0 +1,26 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_MACH_SUN8I_A83T=y
> +CONFIG_DRAM_CLK=480
> +CONFIG_DRAM_ZQ=15355
> +CONFIG_DRAM_ODT_EN=y
> +#CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
> +#CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
> +CONFIG_AXP_GPIO=y
> +#CONFIG_USB_MUSB_HOST=y
> +CONFIG_ARMV7_BOOT_SEC_DEFAULT=y
You can drop this now that you no longer claim to support PSCI.
> +CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-allwinner-h8homlet-v2"
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_SPL=y
> +CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=1"
This is the default please remove this entire line.
> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_CMD_FPGA is not set
> +CONFIG_AXP_DCDC1_VOLT=3000
> +CONFIG_AXP_DCDC2_VOLT=900
> +CONFIG_AXP_DCDC3_VOLT=900
> +CONFIG_AXP_DCDC4_VOLT=0
> +CONFIG_AXP_DCDC5_VOLT=1500
> +CONFIG_AXP_ALDO2_VOLT=0
> +CONFIG_AXP_ALDO3_VOLT=0
> +CONFIG_AXP_DLDO4_VOLT=0
>
Regards,
Hans
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC.
2015-11-13 16:52 ` [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Hans de Goede
2015-11-13 17:05 ` Chen-Yu Tsai
@ 2015-11-14 18:32 ` Vishnu Patekar
1 sibling, 0 replies; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-14 18:32 UTC (permalink / raw)
To: u-boot
Hello Hans,
Thanks for the review.
On Sat, Nov 14, 2015 at 12:52 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Hi,
>
> On 12-11-15 19:09, Vishnu Patekar wrote:
>
>> This patch series adds basic support for Allwinner A83T SOC.
>>
>> Allwinner A83T is octa-core cortex-a7 based SoC.
>> It's clock control unit and prcm, pinmux are different from previous sun8i
>> series.
>> Its processor cores are arragned in two clusters 4 cores each,
>> similar to A80.
>>
>> Only basic clocks are enabled pll1, pll5, pll6.
>> SMP, display, other peripherals support is not yet supported.
>>
>
> Cool stuff, great work! I've a number of comments, I will reply
> to the individual patches with those.
>
> I've tried to get this to run on my own h8_homlet_v2 but
> unfortunately I cannot get it to work. My own board does
> boot into some chinese top-set-box environment when booting
> without a sdcard and connected to a tv. But it does not show
> any output on the uart connector at the bottom right of the
> board (I've tried with 2 different adapters, including the
> one from the Merrii A80 board which has the exact same connector
> on the board).
>
> Not having an uart also means that I cannot get the board into
> FEL mode (I do have a usb A <-> A cable).
>
> I wonder if my board has a broken uart, or if the system
> image uses a different uart by default ?
>
As I observed, Device does not go to FEL mode if no USB A-A cable
connected.
Please connect USB cable and keep pressing 2,on uart with pins PFx and then
power ON. It may help.
> Have you tried booting with u-boot written to sdcard with
> this patch-set ? Does this work, and does the SPL header
> get printend on the bottom right uart connector ?
>
I broke A83T board microsd adapter badly.
I've already ordered Onda 989 Air. Once I receive it, I'll test booting
from microSD.
Wens said it does not work for him.
> Regards,
>
> Hans
>
>
>
>
> This enables booting kernel with initramfs, kernel patch v1 have been sent.
>> I'll send v2 with comments addressed.
>>
>> Vishnu Patekar (10):
>> sunxi: Add Machine Support for A83T SOC
>> sunxi: Add support for UART0 in PB pin group on A83T
>> sunxi: power: axp818: add support for axp818 driver
>> sunxi: power: enabled support for axp818
>> sunxi: do not enable smp for A83T
>> sunxi: clk: add basic clocks for A83T
>> sunxi: Add support for Allwinner A83T DRAM
>> sunxi: do not include display for A83T
>> sunxi: dts: sun8i: Add Allwinner A83T dtsi
>> sunxi: Add suport for A83T HomletV2 Board by Allwinner
>>
>> arch/arm/cpu/armv7/sunxi/Makefile | 7 +
>> arch/arm/cpu/armv7/sunxi/board.c | 8 +-
>> arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++
>> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 +
>> arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c | 424
>> +++++++++++++++++++++
>> arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +
>> arch/arm/dts/Makefile | 2 +
>> arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 64 ++++
>> arch/arm/dts/sun8i-a83t.dtsi | 247 ++++++++++++
>> arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
>> arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304 +++++++++++++++
>> arch/arm/include/asm/arch-sunxi/dram.h | 2 +
>> arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h | 201 ++++++++++
>> arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
>> board/sunxi/Kconfig | 12 +-
>> board/sunxi/MAINTAINERS | 5 +
>> board/sunxi/board.c | 8 +
>> configs/h8_homlet_v2_defconfig | 26 ++
>> drivers/power/Kconfig | 34 +-
>> drivers/power/Makefile | 1 +
>> drivers/power/axp818.c | 132 +++++++
>> include/axp818.h | 75 ++++
>> include/axp_pmic.h | 3 +
>> include/configs/sun8i.h | 2 +
>> include/configs/sunxi-common.h | 2 +-
>> 25 files changed, 1698 insertions(+), 16 deletions(-)
>> create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
>> create mode 100644 arch/arm/cpu/armv7/sunxi/dram_sun8i_a83t.c
>> create mode 100644 arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
>> create mode 100644 arch/arm/dts/sun8i-a83t.dtsi
>> create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>> create mode 100644 arch/arm/include/asm/arch-sunxi/dram_sun8i_a83t.h
>> create mode 100644 configs/h8_homlet_v2_defconfig
>> create mode 100644 drivers/power/axp818.c
>> create mode 100644 include/axp818.h
>>
>>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for A83T SOC
2015-11-13 17:19 ` Hans de Goede
@ 2015-11-14 18:35 ` Vishnu Patekar
0 siblings, 0 replies; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-14 18:35 UTC (permalink / raw)
To: u-boot
Hello,
On Sat, Nov 14, 2015 at 1:19 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Hi,
>
>
> On 12-11-15 19:09, Vishnu Patekar wrote:
>
>> Allwinner A83T is octa-core cortex-a7 SOC.
>>
>> This enables support for A83T.
>>
>> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
>> ---
>> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 ++
>> board/sunxi/Kconfig | 11 ++++++++++-
>> include/configs/sun8i.h | 2 ++
>> 3 files changed, 14 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/cpu/armv7/sunxi/cpu_info.c
>> b/arch/arm/cpu/armv7/sunxi/cpu_info.c
>> index 05fef32..c9b4bc0 100644
>> --- a/arch/arm/cpu/armv7/sunxi/cpu_info.c
>> +++ b/arch/arm/cpu/armv7/sunxi/cpu_info.c
>> @@ -71,6 +71,8 @@ int print_cpuinfo(void)
>> puts("CPU: Allwinner A33 (SUN8I)\n");
>> #elif defined CONFIG_MACH_SUN9I
>> puts("CPU: Allwinner A80 (SUN9I)\n");
>> +#elif defined CONFIG_MACH_SUN8I_A83T
>> + puts("CPU: Allwinner A83T (SUN8I)\n");
>> #else
>> #warning Please update cpu_info.c with correct CPU information
>> puts("CPU: SUNXI Family\n");
>> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
>> index f6f2a60..ea69bf7 100644
>> --- a/board/sunxi/Kconfig
>> +++ b/board/sunxi/Kconfig
>> @@ -68,6 +68,15 @@ config MACH_SUN8I_A33
>> select SUPPORT_SPL
>> select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
>>
>> +config MACH_SUN8I_A83T
>> + bool "sun8i (Allwinner A83T)"
>> + select CPU_V7
>> + select CPU_V7_HAS_NONSEC
>> + select CPU_V7_HAS_VIRT
>> + select SUNXI_GEN_SUN6I
>> + select SUPPORT_SPL
>> + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
>>
>
> Please remove the CPU_V7_HAS_NONSEC, CPU_V7_HAS_VIRT and
> ARMV7_BOOT_SEC_DEFAULT
> options here, these imply enabling PSCI support and we do not yet have PSCI
> code for the A83t. This is also why you need to add RMV7_BOOT_SEC_DEFAULT=y
> to your defconfig to get things to work.
>
> We will need to figure out SMP support later for now just leave these out.
>
>
> Okie, I'll remove it for now.
>
> +
>> config MACH_SUN9I
>> bool "sun9i (Allwinner A80)"
>> select CPU_V7
>> @@ -78,7 +87,7 @@ endchoice
>> # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 ||
>> A33"
>> config MACH_SUN8I
>> bool
>> - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33
>> + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_A83T
>>
>>
>> config DRAM_CLK
>> diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h
>> index 4fc6365..c139e0a 100644
>> --- a/include/configs/sun8i.h
>> +++ b/include/configs/sun8i.h
>> @@ -25,6 +25,8 @@
>> #define CONFIG_ARMV7_PSCI_NR_CPUS 2
>> #elif defined(CONFIG_MACH_SUN8I_A33)
>> #define CONFIG_ARMV7_PSCI_NR_CPUS 4
>> +#elif defined(CONFIG_MACH_SUN8I_A83T)
>> +#define CONFIG_ARMV7_PSCI_NR_CPUS 8
>> #else
>> #error Unsupported sun8i variant
>> #endif
>>
>>
> And this can be dropped too then.
>
Okie , i'll wrap it arround #ifndef MACH_SUN8I_A83T, otherwise it
complains unsupported sun8i variant.
>
> Regards,
>
> Hans
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818
2015-11-13 17:24 ` Hans de Goede
@ 2015-11-14 18:43 ` Vishnu Patekar
0 siblings, 0 replies; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-14 18:43 UTC (permalink / raw)
To: u-boot
Hello,
On Sat, Nov 14, 2015 at 1:24 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Hi,
>
>
> On 12-11-15 19:09, Vishnu Patekar wrote:
>>
>> Enabled support for AXP818 in SPL and u-boot.
>> DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
>>
>> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
>> ---
>> arch/arm/cpu/armv7/sunxi/Makefile | 1 +
>> arch/arm/cpu/armv7/sunxi/pmic_bus.c | 15 +++++++++++++++
>> board/sunxi/board.c | 8 ++++++++
>> include/configs/sunxi-common.h | 2 +-
>> 4 files changed, 25 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/cpu/armv7/sunxi/Makefile
>> b/arch/arm/cpu/armv7/sunxi/Makefile
>> index 459d5d8..929a933 100644
>> --- a/arch/arm/cpu/armv7/sunxi/Makefile
>> +++ b/arch/arm/cpu/armv7/sunxi/Makefile
>> @@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_SUN6I) += tzpc.o
>> obj-$(CONFIG_AXP152_POWER) += pmic_bus.o
>> obj-$(CONFIG_AXP209_POWER) += pmic_bus.o
>> obj-$(CONFIG_AXP221_POWER) += pmic_bus.o
>> +obj-$(CONFIG_AXP818_POWER) += pmic_bus.o
>>
>> ifndef CONFIG_SPL_BUILD
>> ifdef CONFIG_ARMV7_PSCI
>> diff --git a/arch/arm/cpu/armv7/sunxi/pmic_bus.c
>> b/arch/arm/cpu/armv7/sunxi/pmic_bus.c
>> index 9e05127..838831d 100644
>> --- a/arch/arm/cpu/armv7/sunxi/pmic_bus.c
>> +++ b/arch/arm/cpu/armv7/sunxi/pmic_bus.c
>> @@ -26,6 +26,9 @@
>> #define AXP223_DEVICE_ADDR 0x3a3
>> #define AXP223_RUNTIME_ADDR 0x2d
>>
>> +#define AXP818_DEVICE_ADDR 0x3a3
>> +#define AXP818_RUNTIME_ADDR 0x2d
>> +
>
>
> These are exactly the same, please just add a comment that the
> AXP818 addresses are the same as the AXP223 ones instead
> of adding new defines.
Okie, It's going to be so many ifdefs as all voltages are not yet implemented.
>
>
>> int pmic_bus_init(void)
>> {
>> /* This cannot be 0 because it is used in SPL before BSS is ready
>> */
>> @@ -49,6 +52,14 @@ int pmic_bus_init(void)
>> # endif
>> if (ret)
>> return ret;
>> +#elif defined CONFIG_AXP818_POWER
>
>
> And instead of this #elif make the #if above:
>
> #elif defined CONFIG_AXP223_POWER || defined CONFIG_AXP818_POWER
>
>> + ret = rsb_init();
>> + if (ret)
>> + return ret;
>> +
>> + ret = rsb_set_device_address(AXP818_DEVICE_ADDR,
>> AXP818_RUNTIME_ADDR);
>> + if (ret)
>> + return ret;
>> #endif
>>
>> needs_init = 0;
>> @@ -67,6 +78,8 @@ int pmic_bus_read(u8 reg, u8 *data)
>> # else
>> return rsb_read(AXP223_RUNTIME_ADDR, reg, data);
>> # endif
>> +#elif defined CONFIG_AXP818_POWER
>> + return rsb_read(AXP818_RUNTIME_ADDR, reg, data);
>> #endif
>> }
>>
>> @@ -82,6 +95,8 @@ int pmic_bus_write(u8 reg, u8 data)
>> # else
>> return rsb_write(AXP223_RUNTIME_ADDR, reg, data);
>> # endif
>> +#elif CONFIG_AXP818_POWER
>> + return rsb_write(AXP818_RUNTIME_ADDR, reg, data);
>> #endif
>> }
>>
>
> And idem for all the other functions.
okie.
>
>> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
>> index 6ac398c..ebfa94e 100644
>> --- a/board/sunxi/board.c
>> +++ b/board/sunxi/board.c
>> @@ -430,6 +430,14 @@ void sunxi_board_init(void)
>> int power_failed = 0;
>> unsigned long ramsize;
>>
>> +#if defined CONFIG_AXP818_POWER
>> + power_failed = axp_init();
>> + power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
>> + power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
>> + power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
>> + power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
>> +#endif
>> +
>> #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER ||
>> defined CONFIG_AXP221_POWER
>> power_failed = axp_init();
>>
>
> Please do not add this AXP818 specific block, instead modify the block below
> to work for the 818.
>
>> diff --git a/include/configs/sunxi-common.h
>> b/include/configs/sunxi-common.h
>> index ddcfe94..61af897 100644
>> --- a/include/configs/sunxi-common.h
>> +++ b/include/configs/sunxi-common.h
>> @@ -243,7 +243,7 @@ extern int soft_i2c_gpio_scl;
>> #endif
>>
>> /* PMU */
>> -#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined
>> CONFIG_AXP221_POWER
>> +#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined
>> CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
>> #define CONFIG_SPL_POWER_SUPPORT
>> #endif
>>
>>
>
> Regards,
>
> Hans
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks for A83T
2015-11-13 17:25 ` Hans de Goede
@ 2015-11-14 18:47 ` Vishnu Patekar
2015-11-15 2:10 ` Chen-Yu Tsai
0 siblings, 1 reply; 28+ messages in thread
From: Vishnu Patekar @ 2015-11-14 18:47 UTC (permalink / raw)
To: u-boot
Hello,
On Sat, Nov 14, 2015 at 1:25 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Hi,
>
> On 12-11-15 19:09, Vishnu Patekar wrote:
>>
>> Add basic clocks pll1, pll5, and some default values from allwinner
>> u-boot.
>>
>> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
>
>
> This one looks good as is.
I'm going to increase the PLL6 clock as same as allwinner u-boot, i.e. 1200MHz.
How can we know that pll6's safe range. as per data sheet, multiplier
can be 12 to 255.
But, 24*255 Mhz is not realistic.
>
> Regards,
>
> Hans
>
>
>> ---
>> arch/arm/cpu/armv7/sunxi/Makefile | 4 +
>> arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c | 133 +++++++++
>> arch/arm/include/asm/arch-sunxi/clock.h | 4 +-
>> arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 304
>> +++++++++++++++++++++
>> 4 files changed, 444 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
>> create mode 100644 arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>>
>> diff --git a/arch/arm/cpu/armv7/sunxi/Makefile
>> b/arch/arm/cpu/armv7/sunxi/Makefile
>> index 929a933..3c9fed3 100644
>> --- a/arch/arm/cpu/armv7/sunxi/Makefile
>> +++ b/arch/arm/cpu/armv7/sunxi/Makefile
>> @@ -26,7 +26,11 @@ obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o
>> obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o
>> obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o
>> obj-$(CONFIG_MACH_SUN7I) += clock_sun4i.o
>> +ifdef CONFIG_MACH_SUN8I_A83T
>> +obj-y += clock_sun8i_a83t.o
>> +else
>> obj-$(CONFIG_MACH_SUN8I) += clock_sun6i.o
>> +endif
>> obj-$(CONFIG_MACH_SUN9I) += clock_sun9i.o
>> obj-$(CONFIG_MACH_SUN6I) += tzpc.o
>>
>> diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
>> b/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
>> new file mode 100644
>> index 0000000..76efa93
>> --- /dev/null
>> +++ b/arch/arm/cpu/armv7/sunxi/clock_sun8i_a83t.c
>> @@ -0,0 +1,133 @@
>> +/*
>> + * sun6i specific clock code
>> + *
>> + * (C) Copyright 2007-2012
>> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
>> + * Tom Cubie <tangliang@allwinnertech.com>
>> + *
>> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/io.h>
>> +#include <asm/arch/clock.h>
>> +#include <asm/arch/prcm.h>
>> +#include <asm/arch/sys_proto.h>
>> +
>> +#ifdef CONFIG_SPL_BUILD
>> +void clock_init_safe(void)
>> +{
>> + struct sunxi_ccm_reg * const ccm =
>> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
>> +
>> + clock_set_pll1(408000000);
>> + /* enable pll_hsic, default is 480M */
>> + writel(PLL8_CFG_DEFAULT, &ccm->pll8_cfg);
>> + writel(readl(&ccm->pll8_cfg) | (0x1 << 31), &ccm->pll8_cfg);
>> +
>> + /* switch to default 24MHz before changing to hsic */
>> + writel(0x0, &ccm->cci400_cfg);
>> + sdelay(50);
>> + writel(CCM_CCI400_CLK_SEL_HSIC, &ccm->cci400_cfg);
>> + sdelay(100);
>> +
>> + /* switch before changing pll6 */
>> + clrsetbits_le32(&ccm->ahb1_apb1_div, AHB1_CLK_SRC_MASK,
>> + AHB1_CLK_SRC_OSC24M);
>> + writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg);
>> + sdelay(100);
>> +
>> + writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
>> + writel(CCM_MBUS_RESET_RESET, &ccm->mbus_reset);
>> + writel(MBUS_CLK_DEFAULT, &ccm->mbus_clk_cfg);
>> +
>> + /* timestamp */
>> + writel(1, 0x01720000);
>> +}
>> +#endif
>> +
>> +void clock_init_uart(void)
>> +{
>> + struct sunxi_ccm_reg *const ccm =
>> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
>> +
>> + /* uart clock source is apb2 */
>> + writel(APB2_CLK_SRC_OSC24M|
>> + APB2_CLK_RATE_N_1|
>> + APB2_CLK_RATE_M(1),
>> + &ccm->apb2_div);
>> +
>> + /* open the clock for uart */
>> + setbits_le32(&ccm->apb2_gate,
>> + CLK_GATE_OPEN << (APB2_GATE_UART_SHIFT +
>> + CONFIG_CONS_INDEX - 1));
>> +
>> + /* deassert uart reset */
>> + setbits_le32(&ccm->apb2_reset_cfg,
>> + 1 << (APB2_RESET_UART_SHIFT +
>> + CONFIG_CONS_INDEX - 1));
>> +}
>> +
>> +#ifdef CONFIG_SPL_BUILD
>> +void clock_set_pll1(unsigned int clk)
>> +{
>> + struct sunxi_ccm_reg * const ccm =
>> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
>> + const int p = 0;
>> +
>> + /* Switch to 24MHz clock while changing PLL1 */
>> + writel(AXI_DIV_2 << AXI0_DIV_SHIFT |
>> + CPU_CLK_SRC_OSC24M << C0_CPUX_CLK_SRC_SHIFT,
>> + &ccm->cpu_axi_cfg);
>> +
>> + /* clk = 24*n/p, p is ignored if clock is >288MHz */
>> + writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) |
>> CMM_PLL1_CLOCK_TIME_2 |
>> + CCM_PLL1_CTRL_N(clk / 24000000),
>> + &ccm->pll1_c0_cfg);
>> + sdelay(200);
>> +
>> + writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) |
>> CMM_PLL1_CLOCK_TIME_2 |
>> + CCM_PLL1_CTRL_N(clk / (24000000)),
>> + &ccm->pll1_c1_cfg);
>> + sdelay(200);
>> +
>> + /* Switch CPU to PLL1 */
>> + writel(AXI_DIV_2 << AXI0_DIV_SHIFT |
>> + AXI_DIV_2 << AXI1_DIV_SHIFT |
>> + CPU_CLK_SRC_PLL1 << C0_CPUX_CLK_SRC_SHIFT |
>> + CPU_CLK_SRC_PLL1 << C1_CPUX_CLK_SRC_SHIFT,
>> + &ccm->cpu_axi_cfg);
>> +}
>> +#endif
>> +
>> +void clock_set_pll5(unsigned int clk)
>> +{
>> + struct sunxi_ccm_reg * const ccm =
>> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
>> + unsigned int div1 = 0, div2 = 0;
>> +
>> + /* A83T PLL5 DDR rate = 24000000 * (n+1)/(div1+1)/(div2+1) */
>> + writel(CCM_PLL5_CTRL_EN | CCM_PLL5_CTRL_UPD |
>> + CCM_PLL5_CTRL_N(clk / (24000000)) |
>> + div2 << CCM_PLL5_DIV2_SHIFT |
>> + div1 << CCM_PLL5_DIV1_SHIFT, &ccm->pll5_cfg);
>> +
>> + udelay(5500);
>> +}
>> +
>> +
>> +unsigned int clock_get_pll6(void)
>> +{
>> + struct sunxi_ccm_reg *const ccm =
>> + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
>> +
>> + uint32_t rval = readl(&ccm->pll6_cfg);
>> + int n = ((rval & CCM_PLL6_CTRL_N_MASK) >> CCM_PLL6_CTRL_N_SHIFT) +
>> 1;
>> + int div1 = ((rval & CCM_PLL6_CTRL_DIV1_MASK) >>
>> + CCM_PLL6_CTRL_DIV1_SHIFT) + 1;
>> + int div2 = ((rval & CCM_PLL6_CTRL_DIV2_MASK) >>
>> + CCM_PLL6_CTRL_DIV2_SHIFT) + 1;
>> + return 24000000 * n / div1 / div2;
>> +}
>> diff --git a/arch/arm/include/asm/arch-sunxi/clock.h
>> b/arch/arm/include/asm/arch-sunxi/clock.h
>> index 3e5d999..8ca58ae 100644
>> --- a/arch/arm/include/asm/arch-sunxi/clock.h
>> +++ b/arch/arm/include/asm/arch-sunxi/clock.h
>> @@ -15,7 +15,9 @@
>> #define CLK_GATE_CLOSE 0x0
>>
>> /* clock control module regs definition */
>> -#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I)
>> +#if defined(CONFIG_MACH_SUN8I_A83T)
>> +#include <asm/arch/clock_sun8i_a83t.h>
>> +#elif defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I)
>> #include <asm/arch/clock_sun6i.h>
>> #elif defined(CONFIG_MACH_SUN9I)
>> #include <asm/arch/clock_sun9i.h>
>> diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>> b/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>> new file mode 100644
>> index 0000000..28ea16c
>> --- /dev/null
>> +++ b/arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h
>> @@ -0,0 +1,304 @@
>> +/*
>> + * sun8i a83t clock register definitions
>> + *
>> + * (C) Copyright 2007-2011
>> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
>> + * Tom Cubie <tangliang@allwinnertech.com>
>> + *
>> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
>> + * from sun6i.h
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#ifndef _SUNXI_CLOCK_SUN8I_A83T_H
>> +#define _SUNXI_CLOCK_SUN8I_A83T_H
>> +
>> +struct sunxi_ccm_reg {
>> + u32 pll1_c0_cfg; /* 0x00 c1cpu# pll control */
>> + u32 pll1_c1_cfg; /* 0x04 c1cpu# pll control */
>> + u32 pll2_cfg; /* 0x08 pll2 audio control */
>> + u32 reserved1;
>> + u32 pll3_cfg; /* 0x10 pll3 video0 control */
>> + u32 reserved2;
>> + u32 pll4_cfg; /* 0x18 pll4 ve control */
>> + u32 reserved3;
>> + u32 pll5_cfg; /* 0x20 pll5 ddr control */
>> + u32 reserved4;
>> + u32 pll6_cfg; /* 0x28 pll6 peripheral control */
>> + u32 reserved5[3]; /* 0x2c */
>> + u32 pll7_cfg; /* 0x38 pll7 gpu control */
>> + u32 reserved6[2]; /* 3c */
>> + u32 pll8_cfg; /* 0x44 pll8 hsic control */
>> + u32 pll9_cfg; /* 0x48 pll9 de control */
>> + u32 pll10_cfg; /* 0x4c pll10 video1 control */
>> + u32 cpu_axi_cfg; /* 0x50 CPU/AXI divide ratio */
>> + u32 ahb1_apb1_div; /* 0x54 AHB1/APB1 divide ratio */
>> + u32 apb2_div; /* 0x58 APB2 divide ratio */
>> + u32 ahb2_div; /* 0x5c AHB2 divide ratio */
>> + u32 ahb_gate0; /* 0x60 ahb module clock gating 0 */
>> + u32 ahb_gate1; /* 0x64 ahb module clock gating 1 */
>> + u32 apb1_gate; /* 0x68 apb1 module clock gating 3 */
>> + u32 apb2_gate; /* 0x6c apb2 module clock gating 4 */
>> + u32 reserved7[2]; /* 0x70 */
>> + u32 cci400_cfg; /* 0x78 cci400 clock configuration A83T
>> only */
>> + u32 reserved8; /* 0x7c */
>> + u32 nand0_clk_cfg; /* 0x80 nand clock control */
>> + u32 reserved9; /* 0x84 */
>> + u32 sd0_clk_cfg; /* 0x88 sd0 clock control */
>> + u32 sd1_clk_cfg; /* 0x8c sd1 clock control */
>> + u32 sd2_clk_cfg; /* 0x90 sd2 clock control */
>> + u32 sd3_clk_cfg; /* 0x94 sd3 clock control */
>> + u32 reserved10; /* 0x98 */
>> + u32 ss_clk_cfg; /* 0x9c security system clock control */
>> + u32 spi0_clk_cfg; /* 0xa0 spi0 clock control */
>> + u32 spi1_clk_cfg; /* 0xa4 spi1 clock control */
>> + u32 reserved11[2]; /* 0xa8 */
>> + u32 i2s0_clk_cfg; /* 0xb0 I2S0 clock control */
>> + u32 i2s1_clk_cfg; /* 0xb4 I2S1 clock control */
>> + u32 i2s2_clk_cfg; /* 0xb8 I2S2 clock control */
>> + u32 tdm_clk_cfg; /* 0xbc TDM clock control */
>> + u32 spdif_clk_cfg; /* 0xc0 SPDIF clock control */
>> + u32 reserved12[2]; /* c4 */
>> + u32 usb_clk_cfg; /* 0xcc USB clock control */
>> + u32 reserved13[9]; /* d0 */
>> + u32 dram_clk_cfg; /* 0xf4 DRAM configuration clock control
>> */
>> + u32 dram_pll_cfg; /* 0xf8 PLL_DDR cfg register */
>> + u32 mbus_reset; /* 0xfc MBUS reset control */
>> + u32 dram_clk_gate; /* 0x100 DRAM module gating */
>> + u32 reserved14[5]; /* 0x104 BE0 */
>> + u32 lcd0_clk_cfg; /* 0x118 LCD0 module clock */
>> + u32 lcd1_clk_cfg; /* 0x11c LCD1 module clock */
>> + u32 reserved15[4]; /* 0x120 */
>> + u32 mipi_csi_clk_cfg; /* 0x130 MIPI CSI module clock */
>> + u32 csi_clk_cfg; /* 0x134 CSI module clock */
>> + u32 reserved16; /* 0x138 */
>> + u32 ve_clk_cfg; /* 0x13c VE module clock */
>> + u32 reserved17; /* 0x140 */
>> + u32 avs_clk_cfg; /* 0x144 AVS module clock */
>> + u32 reserved18[2]; /* 0x148 */
>> + u32 hdmi_clk_cfg; /* 0x150 HDMI module clock */
>> + u32 hdmi_slow_clk_cfg; /* 0x154 HDMI slow module clock */
>> + u32 reserved19; /* 0x158 */
>> + u32 mbus_clk_cfg; /* 0x15c MBUS module clock */
>> + u32 reserved20[2];
>> + u32 mipi_dsi_clk_cfg; /* 0x168 MIPI DSI clock control */
>> + u32 reserved21[13]; /* 0x16c */
>> + u32 gpu_core_clk_cfg; /* 0x1a0 GPU core clock config */
>> + u32 gpu_mem_clk_cfg; /* 0x1a4 GPU memory clock config */
>> + u32 gpu_hyd_clk_cfg; /* 0x1a8 GPU HYD clock config */
>> + u32 reserved22[21]; /* 0x1ac */
>> + u32 pll_stable0; /* 0x200 PLL stable time 0 */
>> + u32 pll_stable1; /* 0x204 PLL stable time 1 */
>> + u32 reserved23; /* 0x208 */
>> + u32 pll_stable_status; /* 0x20c PLL stable status register */
>> + u32 reserved24[0x04]; /* 0x210 */
>> + u32 pll1_c0_bias_cfg; /* 0x220 PLL1 c0cpu# Bias config */
>> + u32 pll2_bias_cfg; /* 0x224 PLL2 audio Bias config */
>> + u32 pll3_bias_cfg; /* 0x228 PLL3 video Bias config */
>> + u32 pll4_bias_cfg; /* 0x22c PLL4 ve Bias config */
>> + u32 pll5_bias_cfg; /* 0x230 PLL5 ddr Bias config */
>> + u32 pll6_bias_cfg; /* 0x234 PLL6 periph Bias config */
>> + u32 pll1_c1_bias_cfg; /* 0x238 PLL1 c1cpu# Bias config */
>> + u32 pll8_bias_cfg; /* 0x23c PLL7 Bias config */
>> + u32 reserved25; /* 0x240 */
>> + u32 pll9_bias_cfg; /* 0x244 PLL9 hsic Bias config */
>> + u32 de_bias_cfg; /* 0x248 display engine Bias config */
>> + u32 video1_bias_cfg; /* 0x24c pll video1 bias register */
>> + u32 c0_tuning_cfg; /* 0x250 pll c0cpu# tuning register */
>> + u32 c1_tuning_cfg; /* 0x254 pll c1cpu# tuning register */
>> + u32 reserved26[11]; /* 0x258 */
>> + u32 pll2_pattern_cfg0; /* 0x284 PLL2 Pattern register 0 */
>> + u32 pll3_pattern_cfg0; /* 0x288 PLL3 Pattern register 0 */
>> + u32 reserved27; /* 0x28c */
>> + u32 pll5_pattern_cfg0; /* 0x290 PLL5 Pattern register 0*/
>> + u32 reserved28[4]; /* 0x294 */
>> + u32 pll2_pattern_cfg1; /* 0x2a4 PLL2 Pattern register 1 */
>> + u32 pll3_pattern_cfg1; /* 0x2a8 PLL3 Pattern register 1 */
>> + u32 reserved29; /* 0x2ac */
>> + u32 pll5_pattern_cfg1; /* 0x2b0 PLL5 Pattern register 1 */
>> + u32 reserved30[3]; /* 0x2b4 */
>> + u32 ahb_reset0_cfg; /* 0x2c0 AHB1 Reset 0 config */
>> + u32 ahb_reset1_cfg; /* 0x2c4 AHB1 Reset 1 config */
>> + u32 ahb_reset2_cfg; /* 0x2c8 AHB1 Reset 2 config */
>> + u32 reserved31;
>> + u32 ahb_reset3_cfg; /* 0x2d0 AHB1 Reset 3 config */
>> + u32 reserved32; /* 0x2d4 */
>> + u32 apb2_reset_cfg; /* 0x2d8 BUS Reset 4 config */
>> +};
>> +
>> +/* apb2 bit field */
>> +#define APB2_CLK_SRC_LOSC (0x0 << 24)
>> +#define APB2_CLK_SRC_OSC24M (0x1 << 24)
>> +#define APB2_CLK_SRC_PLL6 (0x2 << 24)
>> +#define APB2_CLK_SRC_MASK (0x3 << 24)
>> +#define APB2_CLK_RATE_N_1 (0x0 << 16)
>> +#define APB2_CLK_RATE_N_2 (0x1 << 16)
>> +#define APB2_CLK_RATE_N_4 (0x2 << 16)
>> +#define APB2_CLK_RATE_N_8 (0x3 << 16)
>> +#define APB2_CLK_RATE_N_MASK (3 << 16)
>> +#define APB2_CLK_RATE_M(m) (((m)-1) << 0)
>> +#define APB2_CLK_RATE_M_MASK (0x1f << 0)
>> +
>> +/* apb2 gate field */
>> +#define APB2_GATE_UART_SHIFT (16)
>> +#define APB2_GATE_UART_MASK (0xff << APB2_GATE_UART_SHIFT)
>> +#define APB2_GATE_TWI_SHIFT (0)
>> +#define APB2_GATE_TWI_MASK (0xf << APB2_GATE_TWI_SHIFT)
>> +
>> +/* cpu_axi_cfg bits */
>> +#define AXI0_DIV_SHIFT 0
>> +#define AXI1_DIV_SHIFT 16
>> +#define C0_CPUX_CLK_SRC_SHIFT 12
>> +#define C1_CPUX_CLK_SRC_SHIFT 28
>> +
>> +#define AXI_DIV_1 0
>> +#define AXI_DIV_2 1
>> +#define AXI_DIV_3 2
>> +#define AXI_DIV_4 3
>> +#define CPU_CLK_SRC_OSC24M 0
>> +#define CPU_CLK_SRC_PLL1 1
>> +
>> +#define CCM_PLL1_CTRL_N(n) ((((n) - 1) & 0xff) << 8)
>> +#define CCM_PLL1_CTRL_P(n) (((n) & 0x1) << 16)
>> +#define CCM_PLL1_CTRL_EN (0x1 << 31)
>> +#define CMM_PLL1_CLOCK_TIME_2 (0x2 << 24)
>> +
>> +#define PLL8_CFG_DEFAULT 0x42800
>> +#define CCM_CCI400_CLK_SEL_HSIC (0x2<<24)
>> +
>> +#define CCM_PLL5_DIV1_SHIFT 16
>> +#define CCM_PLL5_DIV2_SHIFT 18
>> +#define CCM_PLL5_CTRL_N(n) (((n) - 1) << 8)
>> +#define CCM_PLL5_CTRL_UPD (0x1 << 30)
>> +#define CCM_PLL5_CTRL_EN (0x1 << 31)
>> +
>> +#define PLL6_CFG_DEFAULT 0x80041800 /* 576 MHz */
>> +#define CCM_PLL6_CTRL_N_SHIFT 8
>> +#define CCM_PLL6_CTRL_N_MASK (0xff << CCM_PLL6_CTRL_N_SHIFT)
>> +#define CCM_PLL6_CTRL_DIV1_SHIFT 16
>> +#define CCM_PLL6_CTRL_DIV1_MASK (0x1 <<
>> CCM_PLL6_CTRL_DIV1_SHIFT)
>> +#define CCM_PLL6_CTRL_DIV2_SHIFT 18
>> +#define CCM_PLL6_CTRL_DIV2_MASK (0x1 <<
>> CCM_PLL6_CTRL_DIV2_SHIFT)
>> +
>> +#define AHB1_ABP1_DIV_DEFAULT 0x00002190
>> +#define AHB1_CLK_SRC_MASK (0x3<<12)
>> +#define AHB1_CLK_SRC_INTOSC (0x0<<12)
>> +#define AHB1_CLK_SRC_OSC24M (0x1<<12)
>> +#define AHB1_CLK_SRC_PLL6 (0x2<<12)
>> +
>> +#define AXI_GATE_OFFSET_DRAM 0
>> +
>> +/* ahb_gate0 offsets */
>> +#define AHB_GATE_OFFSET_USB_OHCI1 30
>> +#define AHB_GATE_OFFSET_USB_OHCI0 29
>> +#define AHB_GATE_OFFSET_USB_EHCI1 27
>> +#define AHB_GATE_OFFSET_USB_EHCI0 26
>> +#define AHB_GATE_OFFSET_USB0 24
>> +#define AHB_GATE_OFFSET_SPI1 21
>> +#define AHB_GATE_OFFSET_SPI0 20
>> +#define AHB_GATE_OFFSET_HSTIMER 19
>> +#define AHB_GATE_OFFSET_EMAC 17
>> +#define AHB_GATE_OFFSET_MCTL 14
>> +#define AHB_GATE_OFFSET_GMAC 17
>> +#define AHB_GATE_OFFSET_NAND0 13
>> +#define AHB_GATE_OFFSET_MMC0 8
>> +#define AHB_GATE_OFFSET_MMC(n) (AHB_GATE_OFFSET_MMC0 + (n))
>> +#define AHB_GATE_OFFSET_DMA 6
>> +#define AHB_GATE_OFFSET_SS 5
>> +
>> +/* ahb_gate1 offsets */
>> +#define AHB_GATE_OFFSET_DRC0 25
>> +#define AHB_GATE_OFFSET_DE_FE0 14
>> +#define AHB_GATE_OFFSET_DE_BE0 12
>> +#define AHB_GATE_OFFSET_HDMI 11
>> +#define AHB_GATE_OFFSET_LCD1 5
>> +#define AHB_GATE_OFFSET_LCD0 4
>> +
>> +#define CCM_MMC_CTRL_M(x) ((x) - 1)
>> +#define CCM_MMC_CTRL_OCLK_DLY(x) ((x) << 8)
>> +#define CCM_MMC_CTRL_N(x) ((x) << 16)
>> +#define CCM_MMC_CTRL_SCLK_DLY(x) ((x) << 20)
>> +#define CCM_MMC_CTRL_OSCM24 (0x0 << 24)
>> +#define CCM_MMC_CTRL_PLL6 (0x1 << 24)
>> +#define CCM_MMC_CTRL_ENABLE (0x1 << 31)
>> +
>> +#define CCM_USB_CTRL_PHY0_RST (0x1 << 0)
>> +#define CCM_USB_CTRL_PHY1_RST (0x1 << 1)
>> +#define CCM_USB_CTRL_PHY2_RST (0x1 << 2)
>> +/* There is no global phy clk gate on sun6i, define as 0 */
>> +#define CCM_USB_CTRL_PHYGATE 0
>> +#define CCM_USB_CTRL_PHY0_CLK (0x1 << 8)
>> +#define CCM_USB_CTRL_PHY1_CLK (0x1 << 9)
>> +#define CCM_USB_CTRL_PHY2_CLK (0x1 << 10)
>> +#define CCM_USB_CTRL_OHCI0_CLK (0x1 << 16)
>> +#define CCM_USB_CTRL_OHCI1_CLK (0x1 << 17)
>> +
>> +#define CCM_GMAC_CTRL_TX_CLK_SRC_MII 0x0
>> +#define CCM_GMAC_CTRL_TX_CLK_SRC_EXT_RGMII 0x1
>> +#define CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII 0x2
>> +#define CCM_GMAC_CTRL_GPIT_MII (0x0 << 2)
>> +#define CCM_GMAC_CTRL_GPIT_RGMII (0x1 << 2)
>> +#define CCM_GMAC_CTRL_RX_CLK_DELAY(x) ((x) << 5)
>> +#define CCM_GMAC_CTRL_TX_CLK_DELAY(x) ((x) << 10)
>> +
>> +#define MDFS_CLK_DEFAULT 0x81000002 /* PLL6 / 3 */
>> +
>> +#define CCM_DRAMCLK_CFG_DIV(x) ((x - 1) << 0)
>> +#define CCM_DRAMCLK_CFG_DIV_MASK (0xf << 0)
>> +#define CCM_DRAMCLK_CFG_DIV0(x) ((x - 1) << 8)
>> +#define CCM_DRAMCLK_CFG_DIV0_MASK (0xf << 8)
>> +#define CCM_DRAMCLK_CFG_UPD (0x1 << 16)
>> +#define CCM_DRAMCLK_CFG_RST (0x1 << 31)
>> +
>> +#define CCM_DRAMPLL_CFG_SRC_PLL5 (0x0 << 16) /* Select PLL5 (DDR0)
>> */
>> +#define CCM_DRAMPLL_CFG_SRC_PLL11 (0x1 << 16) /* Select PLL11 (DDR1)
>> */
>> +#define CCM_DRAMPLL_CFG_SRC_MASK (0x1 << 16)
>> +
>> +#define CCM_MBUS_RESET_RESET (0x1 << 31)
>> +
>> +#define CCM_DRAM_GATE_OFFSET_DE_FE0 24
>> +#define CCM_DRAM_GATE_OFFSET_DE_FE1 25
>> +#define CCM_DRAM_GATE_OFFSET_DE_BE0 26
>> +#define CCM_DRAM_GATE_OFFSET_DE_BE1 27
>> +
>> +
>> +#define MBUS_CLK_DEFAULT 0x81000002 /* PLL6 / 2 */
>> +
>> +#define MBUS_CLK_GATE (0x1 << 31)
>> +
>> +/* ahb_reset0 offsets */
>> +#define AHB_RESET_OFFSET_GMAC 17
>> +#define AHB_RESET_OFFSET_MCTL 14
>> +#define AHB_RESET_OFFSET_MMC3 11
>> +#define AHB_RESET_OFFSET_MMC2 10
>> +#define AHB_RESET_OFFSET_MMC1 9
>> +#define AHB_RESET_OFFSET_MMC0 8
>> +#define AHB_RESET_OFFSET_MMC(n) (AHB_RESET_OFFSET_MMC0 +
>> (n))
>> +#define AHB_RESET_OFFSET_SS 5
>> +
>> +/* ahb_reset1 offsets */
>> +#define AHB_RESET_OFFSET_SAT 26
>> +#define AHB_RESET_OFFSET_DRC0 25
>> +#define AHB_RESET_OFFSET_DE_FE0 14
>> +#define AHB_RESET_OFFSET_DE_BE0 12
>> +#define AHB_RESET_OFFSET_HDMI 11
>> +#define AHB_RESET_OFFSET_LCD1 5
>> +#define AHB_RESET_OFFSET_LCD0 4
>> +
>> +/* ahb_reset2 offsets */
>> +#define AHB_RESET_OFFSET_LVDS 0
>> +
>> +/* apb2 reset */
>> +#define APB2_RESET_UART_SHIFT (16)
>> +#define APB2_RESET_UART_MASK (0xff << APB2_RESET_UART_SHIFT)
>> +#define APB2_RESET_TWI_SHIFT (0)
>> +#define APB2_RESET_TWI_MASK (0xf << APB2_RESET_TWI_SHIFT)
>> +
>> +
>> +#ifndef __ASSEMBLY__
>> +void clock_set_pll1(unsigned int hz);
>> +void clock_set_pll5(unsigned int clk);
>> +unsigned int clock_get_pll6(void);
>> +#endif
>> +
>> +#endif /* _SUNXI_CLOCK_SUN8I_A83T_H */
>>
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks for A83T
2015-11-14 18:47 ` Vishnu Patekar
@ 2015-11-15 2:10 ` Chen-Yu Tsai
0 siblings, 0 replies; 28+ messages in thread
From: Chen-Yu Tsai @ 2015-11-15 2:10 UTC (permalink / raw)
To: u-boot
Hi,
On Sun, Nov 15, 2015 at 2:47 AM, Vishnu Patekar
<vishnupatekar0510@gmail.com> wrote:
> Hello,
>
> On Sat, Nov 14, 2015 at 1:25 AM, Hans de Goede <hdegoede@redhat.com> wrote:
>> Hi,
>>
>> On 12-11-15 19:09, Vishnu Patekar wrote:
>>>
>>> Add basic clocks pll1, pll5, and some default values from allwinner
>>> u-boot.
>>>
>>> Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
>>
>>
>> This one looks good as is.
> I'm going to increase the PLL6 clock as same as allwinner u-boot, i.e. 1200MHz.
>
> How can we know that pll6's safe range. as per data sheet, multiplier
> can be 12 to 255.
> But, 24*255 Mhz is not realistic.
You probably shouldn't. The user manual says that the PLL should be 600 MHz.
The default value of 0x00001900 is also 600 MHz, only turned off.
ChenYu
^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2015-11-15 2:10 UTC | newest]
Thread overview: 28+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-11-12 18:09 [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 01/10] sunxi: Add Machine Support for " Vishnu Patekar
2015-11-13 17:19 ` Hans de Goede
2015-11-14 18:35 ` Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 02/10] sunxi: Add support for UART0 in PB pin group on A83T Vishnu Patekar
2015-11-13 17:19 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver Vishnu Patekar
2015-11-13 17:21 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 04/10] sunxi: power: enabled support for axp818 Vishnu Patekar
2015-11-13 17:24 ` Hans de Goede
2015-11-14 18:43 ` Vishnu Patekar
2015-11-12 18:09 ` [U-Boot] [PATCH 05/10] sunxi: do not enable smp for A83T Vishnu Patekar
2015-11-13 17:24 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 06/10] sunxi: clk: add basic clocks " Vishnu Patekar
2015-11-13 17:25 ` Hans de Goede
2015-11-14 18:47 ` Vishnu Patekar
2015-11-15 2:10 ` Chen-Yu Tsai
2015-11-12 18:09 ` [U-Boot] [PATCH 07/10] sunxi: Add support for Allwinner A83T DRAM Vishnu Patekar
2015-11-13 17:25 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 08/10] sunxi: do not include display for A83T Vishnu Patekar
2015-11-13 17:25 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 09/10] sunxi: dts: sun8i: Add Allwinner A83T dtsi Vishnu Patekar
2015-11-13 17:26 ` Hans de Goede
2015-11-12 18:09 ` [U-Boot] [PATCH 10/10] sunxi: Add suport for A83T HomletV2 Board by Allwinner Vishnu Patekar
2015-11-13 17:27 ` Hans de Goede
2015-11-13 16:52 ` [U-Boot] [PATCH 00/10] basic support for Allwinner A83T SOC Hans de Goede
2015-11-13 17:05 ` Chen-Yu Tsai
2015-11-14 18:32 ` Vishnu Patekar
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.