* [PATCH v1] arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3 mezzanine
@ 2020-04-22 11:10 Robert Foss
2020-05-14 17:22 ` Vinod Koul
0 siblings, 1 reply; 3+ messages in thread
From: Robert Foss @ 2020-04-22 11:10 UTC (permalink / raw)
To: agross, bjorn.andersson, robh+dt, linux-arm-msm, devicetree,
linux-kernel
Cc: Robert Foss
Add device treee support for the Qualcomm APQ8016 SBC, otherwise known as
the Dragonboard 410c with the D3 mezzanine expansion board.
The D3 mezzanine ships in a kit with a OmniVision 5640 sensor module,
which is what this DT targets.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts | 45 +++++++++++++++++++++
2 files changed, 46 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index cc103f7020fd..025362471929 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
new file mode 100644
index 000000000000..1b85adeeada1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "apq8016-sbc.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. APQ 8016 SBC w/ D3 Mezzanine";
+ compatible = "qcom,apq8016-sbc", "qcom,apq8016", "qcom,sbc";
+};
+
+&cci_i2c0 {
+ /delete-node/ camera_rear@3b;
+
+ camera_rear@76 {
+ compatible = "ovti,ov5640";
+ reg = <0x76>;
+
+ enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_rear_default>;
+
+ clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+ clock-names = "xclk";
+ clock-frequency = <23880000>;
+
+ vdddo-supply = <&camera_vdddo_1v8>;
+ vdda-supply = <&camera_vdda_2v8>;
+ vddd-supply = <&camera_vddd_1v5>;
+
+ status = "ok";
+
+ port {
+ ov5640_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2>;
+ remote-endpoint = <&csiphy0_ep>;
+ };
+ };
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH v1] arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3 mezzanine
2020-04-22 11:10 [PATCH v1] arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3 mezzanine Robert Foss
@ 2020-05-14 17:22 ` Vinod Koul
2020-05-15 8:31 ` Robert Foss
0 siblings, 1 reply; 3+ messages in thread
From: Vinod Koul @ 2020-05-14 17:22 UTC (permalink / raw)
To: Robert Foss
Cc: agross, bjorn.andersson, robh+dt, linux-arm-msm, devicetree,
linux-kernel
On 22-04-20, 13:10, Robert Foss wrote:
> Add device treee support for the Qualcomm APQ8016 SBC, otherwise known as
> the Dragonboard 410c with the D3 mezzanine expansion board.
>
> The D3 mezzanine ships in a kit with a OmniVision 5640 sensor module,
> which is what this DT targets.
>
> Signed-off-by: Robert Foss <robert.foss@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts | 45 +++++++++++++++++++++
> 2 files changed, 46 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index cc103f7020fd..025362471929 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -1,5 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
> dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
> new file mode 100644
> index 000000000000..1b85adeeada1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
> @@ -0,0 +1,45 @@
> +// SPDX-License-Identifier: GPL-2.0-only
Dual BSD + GPL please
> +/*
> + * Copyright (c) 2015, The Linux Foundation. All rights reserved.
we are in 2020 now :)
> + */
> +
> +/dts-v1/;
> +
> +#include "apq8016-sbc.dtsi"
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. APQ 8016 SBC w/ D3 Mezzanine";
> + compatible = "qcom,apq8016-sbc", "qcom,apq8016", "qcom,sbc";
> +};
> +
> +&cci_i2c0 {
> + /delete-node/ camera_rear@3b;
> +
> + camera_rear@76 {
> + compatible = "ovti,ov5640";
> + reg = <0x76>;
> +
> + enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&camera_rear_default>;
> +
> + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
> + clock-names = "xclk";
> + clock-frequency = <23880000>;
> +
> + vdddo-supply = <&camera_vdddo_1v8>;
> + vdda-supply = <&camera_vdda_2v8>;
> + vddd-supply = <&camera_vddd_1v5>;
> +
> + status = "ok";
> +
> + port {
> + ov5640_ep: endpoint {
> + clock-lanes = <1>;
> + data-lanes = <0 2>;
> + remote-endpoint = <&csiphy0_ep>;
> + };
> + };
> + };
> +};
> --
> 2.25.1
--
~Vinod
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH v1] arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3 mezzanine
2020-05-14 17:22 ` Vinod Koul
@ 2020-05-15 8:31 ` Robert Foss
0 siblings, 0 replies; 3+ messages in thread
From: Robert Foss @ 2020-05-15 8:31 UTC (permalink / raw)
To: Vinod Koul
Cc: Andy Gross, Bjorn Andersson, Rob Herring, linux-arm-msm,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
On Thu, 14 May 2020 at 19:22, Vinod Koul <vkoul@kernel.org> wrote:
>
> On 22-04-20, 13:10, Robert Foss wrote:
> > Add device treee support for the Qualcomm APQ8016 SBC, otherwise known as
> > the Dragonboard 410c with the D3 mezzanine expansion board.
> >
> > The D3 mezzanine ships in a kit with a OmniVision 5640 sensor module,
> > which is what this DT targets.
> >
> > Signed-off-by: Robert Foss <robert.foss@linaro.org>
> > ---
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts | 45 +++++++++++++++++++++
> > 2 files changed, 46 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
> >
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> > index cc103f7020fd..025362471929 100644
> > --- a/arch/arm64/boot/dts/qcom/Makefile
> > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > @@ -1,5 +1,6 @@
> > # SPDX-License-Identifier: GPL-2.0
> > dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
> > diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
> > new file mode 100644
> > index 000000000000..1b85adeeada1
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-d3.dts
> > @@ -0,0 +1,45 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
>
> Dual BSD + GPL please
Thanks.
>
> > +/*
> > + * Copyright (c) 2015, The Linux Foundation. All rights reserved.
>
> we are in 2020 now :)
Maybe I should fix that.
I'll change the name of the d3 mezzanine to d3camera as well.
>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "apq8016-sbc.dtsi"
> > +
> > +/ {
> > + model = "Qualcomm Technologies, Inc. APQ 8016 SBC w/ D3 Mezzanine";
> > + compatible = "qcom,apq8016-sbc", "qcom,apq8016", "qcom,sbc";
> > +};
> > +
> > +&cci_i2c0 {
> > + /delete-node/ camera_rear@3b;
> > +
> > + camera_rear@76 {
> > + compatible = "ovti,ov5640";
> > + reg = <0x76>;
> > +
> > + enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&camera_rear_default>;
> > +
> > + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
> > + clock-names = "xclk";
> > + clock-frequency = <23880000>;
> > +
> > + vdddo-supply = <&camera_vdddo_1v8>;
> > + vdda-supply = <&camera_vdda_2v8>;
> > + vddd-supply = <&camera_vddd_1v5>;
> > +
> > + status = "ok";
> > +
> > + port {
> > + ov5640_ep: endpoint {
> > + clock-lanes = <1>;
> > + data-lanes = <0 2>;
> > + remote-endpoint = <&csiphy0_ep>;
> > + };
> > + };
> > + };
> > +};
> > --
> > 2.25.1
>
> --
> ~Vinod
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-05-15 8:31 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-04-22 11:10 [PATCH v1] arm64: dts: qcom: apq8016-sbc-d3: Add Qualcomm APQ8016 SBC + D3 mezzanine Robert Foss
2020-05-14 17:22 ` Vinod Koul
2020-05-15 8:31 ` Robert Foss
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.