* Does 99x0 support mesh mode?
@ 2016-07-08 4:52 Yu-Chieh
2016-07-08 17:15 ` Yeoh Chun-Yeow
0 siblings, 1 reply; 9+ messages in thread
From: Yu-Chieh @ 2016-07-08 4:52 UTC (permalink / raw)
To: ath10k
Hi,
Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
Best regards,
Jay
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-08 4:52 Does 99x0 support mesh mode? Yu-Chieh
@ 2016-07-08 17:15 ` Yeoh Chun-Yeow
2016-07-08 17:48 ` Peter Oh
0 siblings, 1 reply; 9+ messages in thread
From: Yeoh Chun-Yeow @ 2016-07-08 17:15 UTC (permalink / raw)
To: Yu-Chieh; +Cc: ath10k
Make sure the firmware has the raw mode feature bit enabled to support mesh.
---
Chun-Yeow
On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
> Hi,
>
> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>
> Best regards,
>
> Jay
>
> _______________________________________________
> ath10k mailing list
> ath10k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-08 17:15 ` Yeoh Chun-Yeow
@ 2016-07-08 17:48 ` Peter Oh
2016-07-09 2:57 ` Yu-Chieh
0 siblings, 1 reply; 9+ messages in thread
From: Peter Oh @ 2016-07-08 17:48 UTC (permalink / raw)
To: Yeoh Chun-Yeow, Yu-Chieh; +Cc: ath10k
On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
> Make sure the firmware has the raw mode feature bit enabled to support
> mesh.
In addition to that, you may check out wmi_services (cat
/sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
native Wi-Fi mode.
> ---
> Chun-Yeow
>
> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>> Hi,
>>
>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>
>> Best regards,
>>
>> Jay
>>
>> _______________________________________________
>> ath10k mailing list
>> ath10k@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/ath10k
>
Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-08 17:48 ` Peter Oh
@ 2016-07-09 2:57 ` Yu-Chieh
2016-07-09 3:25 ` Yu-Chieh
0 siblings, 1 reply; 9+ messages in thread
From: Yu-Chieh @ 2016-07-09 2:57 UTC (permalink / raw)
To: Peter Oh; +Cc: Yeoh Chun-Yeow, ath10k
i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
regarding ram mode, i think it's not supported
<6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
<6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
1:1 crc32 77b2338a
<4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
peers: 528 tid: 132
<4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
<6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
regarding wmi_service, i have checked
/sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
WMI_SERVICE_MESH_11S -
WMI_SERVICE_MESH_NON_11S enabled
Any one knows MESH_NON_11S ?
Jay
2016-07-09 1:48 GMT+08:00 Peter Oh <poh@codeaurora.org>:
>
> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>
>> Make sure the firmware has the raw mode feature bit enabled to support
>> mesh.
>
> In addition to that, you may check out wmi_services (cat
> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
> native Wi-Fi mode.
>
>> ---
>> Chun-Yeow
>>
>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>
>>> Hi,
>>>
>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>
>>> Best regards,
>>>
>>> Jay
>>>
>>> _______________________________________________
>>> ath10k mailing list
>>> ath10k@lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>
>>
> Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-09 2:57 ` Yu-Chieh
@ 2016-07-09 3:25 ` Yu-Chieh
2016-07-09 15:15 ` Yeoh Chun-Yeow
0 siblings, 1 reply; 9+ messages in thread
From: Yu-Chieh @ 2016-07-09 3:25 UTC (permalink / raw)
To: Peter Oh; +Cc: Yeoh Chun-Yeow, ath10k
OK, i think it's not supported now
# iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork
# ifconfig mp0 up
[ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 ti
d: 132
[ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
[ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m
esh interfaces
ifconfig: SIOCSIFFLAGS: Invalid argument
then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw
fail log as following
[ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa
re
[ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2
2
[ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22)
Jay
2016-07-09 10:57 GMT+08:00 Yu-Chieh <jay0607@gmail.com>:
> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
>
> regarding ram mode, i think it's not supported
> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
> 1:1 crc32 77b2338a
> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
> peers: 528 tid: 132
> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
>
> regarding wmi_service, i have checked
> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
> WMI_SERVICE_MESH_11S -
> WMI_SERVICE_MESH_NON_11S enabled
>
> Any one knows MESH_NON_11S ?
>
> Jay
>
> 2016-07-09 1:48 GMT+08:00 Peter Oh <poh@codeaurora.org>:
>>
>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>>
>>> Make sure the firmware has the raw mode feature bit enabled to support
>>> mesh.
>>
>> In addition to that, you may check out wmi_services (cat
>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
>> native Wi-Fi mode.
>>
>>> ---
>>> Chun-Yeow
>>>
>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>>
>>>> Hi,
>>>>
>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>>
>>>> Best regards,
>>>>
>>>> Jay
>>>>
>>>> _______________________________________________
>>>> ath10k mailing list
>>>> ath10k@lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>>
>> Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-09 3:25 ` Yu-Chieh
@ 2016-07-09 15:15 ` Yeoh Chun-Yeow
2016-07-09 15:58 ` Yu-Chieh
0 siblings, 1 reply; 9+ messages in thread
From: Yeoh Chun-Yeow @ 2016-07-09 15:15 UTC (permalink / raw)
To: Yu-Chieh; +Cc: Peter Oh, ath10k
Take a look on the firmware here for your hardware and see how:
https://github.com/kvalo/ath10k-firmware
Regards,
Chun-Yeow
On Sat, Jul 9, 2016 at 11:25 AM, Yu-Chieh <jay0607@gmail.com> wrote:
> OK, i think it's not supported now
> # iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork
> # ifconfig mp0 up
> [ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 ti
> d: 132
> [ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
> [ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m
> esh interfaces
> ifconfig: SIOCSIFFLAGS: Invalid argument
>
> then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw
> fail log as following
> [ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa
> re
> [ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2
> 2
> [ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22)
>
> Jay
>
> 2016-07-09 10:57 GMT+08:00 Yu-Chieh <jay0607@gmail.com>:
>> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
>>
>> regarding ram mode, i think it's not supported
>> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
>> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
>> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
>> 1:1 crc32 77b2338a
>> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
>> peers: 528 tid: 132
>> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
>> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
>>
>> regarding wmi_service, i have checked
>> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
>> WMI_SERVICE_MESH_11S -
>> WMI_SERVICE_MESH_NON_11S enabled
>>
>> Any one knows MESH_NON_11S ?
>>
>> Jay
>>
>> 2016-07-09 1:48 GMT+08:00 Peter Oh <poh@codeaurora.org>:
>>>
>>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>>>
>>>> Make sure the firmware has the raw mode feature bit enabled to support
>>>> mesh.
>>>
>>> In addition to that, you may check out wmi_services (cat
>>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
>>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
>>> native Wi-Fi mode.
>>>
>>>> ---
>>>> Chun-Yeow
>>>>
>>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>>>
>>>>> Hi,
>>>>>
>>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>>>
>>>>> Best regards,
>>>>>
>>>>> Jay
>>>>>
>>>>> _______________________________________________
>>>>> ath10k mailing list
>>>>> ath10k@lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>
>>>>
>>> Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-09 15:15 ` Yeoh Chun-Yeow
@ 2016-07-09 15:58 ` Yu-Chieh
2016-07-09 16:26 ` Yeoh Chun-Yeow
0 siblings, 1 reply; 9+ messages in thread
From: Yu-Chieh @ 2016-07-09 15:58 UTC (permalink / raw)
To: Yeoh Chun-Yeow; +Cc: Peter Oh, ath10k
Thanks Chun-Yeow
Try the firmware on https://github.com/kvalo/ath10k-firmware
the firmware still not support RAW mode
Jay
2016-07-09 23:15 GMT+08:00 Yeoh Chun-Yeow <yeohchunyeow@gmail.com>:
> Take a look on the firmware here for your hardware and see how:
> https://github.com/kvalo/ath10k-firmware
>
> Regards,
> Chun-Yeow
>
> On Sat, Jul 9, 2016 at 11:25 AM, Yu-Chieh <jay0607@gmail.com> wrote:
>> OK, i think it's not supported now
>> # iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork
>> # ifconfig mp0 up
>> [ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 ti
>> d: 132
>> [ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>> [ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m
>> esh interfaces
>> ifconfig: SIOCSIFFLAGS: Invalid argument
>>
>> then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw
>> fail log as following
>> [ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa
>> re
>> [ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2
>> 2
>> [ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22)
>>
>> Jay
>>
>> 2016-07-09 10:57 GMT+08:00 Yu-Chieh <jay0607@gmail.com>:
>>> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
>>>
>>> regarding ram mode, i think it's not supported
>>> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
>>> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
>>> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
>>> 1:1 crc32 77b2338a
>>> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
>>> peers: 528 tid: 132
>>> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>>> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
>>> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
>>>
>>> regarding wmi_service, i have checked
>>> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
>>> WMI_SERVICE_MESH_11S -
>>> WMI_SERVICE_MESH_NON_11S enabled
>>>
>>> Any one knows MESH_NON_11S ?
>>>
>>> Jay
>>>
>>> 2016-07-09 1:48 GMT+08:00 Peter Oh <poh@codeaurora.org>:
>>>>
>>>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>>>>
>>>>> Make sure the firmware has the raw mode feature bit enabled to support
>>>>> mesh.
>>>>
>>>> In addition to that, you may check out wmi_services (cat
>>>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
>>>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
>>>> native Wi-Fi mode.
>>>>
>>>>> ---
>>>>> Chun-Yeow
>>>>>
>>>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>>>>
>>>>>> Hi,
>>>>>>
>>>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>>>>
>>>>>> Best regards,
>>>>>>
>>>>>> Jay
>>>>>>
>>>>>> _______________________________________________
>>>>>> ath10k mailing list
>>>>>> ath10k@lists.infradead.org
>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>
>>>>>
>>>> Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-09 15:58 ` Yu-Chieh
@ 2016-07-09 16:26 ` Yeoh Chun-Yeow
2016-07-10 17:44 ` Yu-Chieh
0 siblings, 1 reply; 9+ messages in thread
From: Yeoh Chun-Yeow @ 2016-07-09 16:26 UTC (permalink / raw)
To: Yu-Chieh; +Cc: Peter Oh, ath10k
You can try the hardware using QCA988X.
ath10k_pci 0000:03:00.0: firmware ver 10.2.4.70.52 api 5 features
no-p2p,raw-mode,mfp crc32 67c4d25c
ath10k_pci 0000:03:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta
128 raw 1 hwcrypto 1
----
Chun-Yeow
On Sat, Jul 9, 2016 at 11:58 PM, Yu-Chieh <jay0607@gmail.com> wrote:
> Thanks Chun-Yeow
>
> Try the firmware on https://github.com/kvalo/ath10k-firmware
> the firmware still not support RAW mode
>
> Jay
>
> 2016-07-09 23:15 GMT+08:00 Yeoh Chun-Yeow <yeohchunyeow@gmail.com>:
>> Take a look on the firmware here for your hardware and see how:
>> https://github.com/kvalo/ath10k-firmware
>>
>> Regards,
>> Chun-Yeow
>>
>> On Sat, Jul 9, 2016 at 11:25 AM, Yu-Chieh <jay0607@gmail.com> wrote:
>>> OK, i think it's not supported now
>>> # iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork
>>> # ifconfig mp0 up
>>> [ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 ti
>>> d: 132
>>> [ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>>> [ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m
>>> esh interfaces
>>> ifconfig: SIOCSIFFLAGS: Invalid argument
>>>
>>> then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw
>>> fail log as following
>>> [ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa
>>> re
>>> [ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2
>>> 2
>>> [ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22)
>>>
>>> Jay
>>>
>>> 2016-07-09 10:57 GMT+08:00 Yu-Chieh <jay0607@gmail.com>:
>>>> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
>>>>
>>>> regarding ram mode, i think it's not supported
>>>> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
>>>> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
>>>> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
>>>> 1:1 crc32 77b2338a
>>>> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
>>>> peers: 528 tid: 132
>>>> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>>>> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
>>>> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
>>>>
>>>> regarding wmi_service, i have checked
>>>> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
>>>> WMI_SERVICE_MESH_11S -
>>>> WMI_SERVICE_MESH_NON_11S enabled
>>>>
>>>> Any one knows MESH_NON_11S ?
>>>>
>>>> Jay
>>>>
>>>> 2016-07-09 1:48 GMT+08:00 Peter Oh <poh@codeaurora.org>:
>>>>>
>>>>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>>>>>
>>>>>> Make sure the firmware has the raw mode feature bit enabled to support
>>>>>> mesh.
>>>>>
>>>>> In addition to that, you may check out wmi_services (cat
>>>>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
>>>>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
>>>>> native Wi-Fi mode.
>>>>>
>>>>>> ---
>>>>>> Chun-Yeow
>>>>>>
>>>>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>>>>>
>>>>>>> Hi,
>>>>>>>
>>>>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>>>>>
>>>>>>> Best regards,
>>>>>>>
>>>>>>> Jay
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> ath10k mailing list
>>>>>>> ath10k@lists.infradead.org
>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>
>>>>>>
>>>>> Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Does 99x0 support mesh mode?
2016-07-09 16:26 ` Yeoh Chun-Yeow
@ 2016-07-10 17:44 ` Yu-Chieh
0 siblings, 0 replies; 9+ messages in thread
From: Yu-Chieh @ 2016-07-10 17:44 UTC (permalink / raw)
To: Yeoh Chun-Yeow; +Cc: Peter Oh, ath10k
Thanks Chun-Yeow,
I am focus on 99x0. so i don't consider 988x.
BTW, thanks for confirm the firmware of 988x supports RAM mode.
Jay
2016-07-10 0:26 GMT+08:00 Yeoh Chun-Yeow <yeohchunyeow@gmail.com>:
> You can try the hardware using QCA988X.
>
> ath10k_pci 0000:03:00.0: firmware ver 10.2.4.70.52 api 5 features
> no-p2p,raw-mode,mfp crc32 67c4d25c
> ath10k_pci 0000:03:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta
> 128 raw 1 hwcrypto 1
>
> ----
> Chun-Yeow
>
> On Sat, Jul 9, 2016 at 11:58 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>> Thanks Chun-Yeow
>>
>> Try the firmware on https://github.com/kvalo/ath10k-firmware
>> the firmware still not support RAW mode
>>
>> Jay
>>
>> 2016-07-09 23:15 GMT+08:00 Yeoh Chun-Yeow <yeohchunyeow@gmail.com>:
>>> Take a look on the firmware here for your hardware and see how:
>>> https://github.com/kvalo/ath10k-firmware
>>>
>>> Regards,
>>> Chun-Yeow
>>>
>>> On Sat, Jul 9, 2016 at 11:25 AM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>> OK, i think it's not supported now
>>>> # iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork
>>>> # ifconfig mp0 up
>>>> [ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 ti
>>>> d: 132
>>>> [ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>>>> [ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m
>>>> esh interfaces
>>>> ifconfig: SIOCSIFFLAGS: Invalid argument
>>>>
>>>> then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw
>>>> fail log as following
>>>> [ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa
>>>> re
>>>> [ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2
>>>> 2
>>>> [ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22)
>>>>
>>>> Jay
>>>>
>>>> 2016-07-09 10:57 GMT+08:00 Yu-Chieh <jay0607@gmail.com>:
>>>>> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
>>>>>
>>>>> regarding ram mode, i think it's not supported
>>>>> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
>>>>> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
>>>>> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
>>>>> 1:1 crc32 77b2338a
>>>>> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
>>>>> peers: 528 tid: 132
>>>>> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32
>>>>> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
>>>>> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
>>>>>
>>>>> regarding wmi_service, i have checked
>>>>> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
>>>>> WMI_SERVICE_MESH_11S -
>>>>> WMI_SERVICE_MESH_NON_11S enabled
>>>>>
>>>>> Any one knows MESH_NON_11S ?
>>>>>
>>>>> Jay
>>>>>
>>>>> 2016-07-09 1:48 GMT+08:00 Peter Oh <poh@codeaurora.org>:
>>>>>>
>>>>>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>>>>>>
>>>>>>> Make sure the firmware has the raw mode feature bit enabled to support
>>>>>>> mesh.
>>>>>>
>>>>>> In addition to that, you may check out wmi_services (cat
>>>>>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
>>>>>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
>>>>>> native Wi-Fi mode.
>>>>>>
>>>>>>> ---
>>>>>>> Chun-Yeow
>>>>>>>
>>>>>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607@gmail.com> wrote:
>>>>>>>>
>>>>>>>> Hi,
>>>>>>>>
>>>>>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>>>>>>
>>>>>>>> Best regards,
>>>>>>>>
>>>>>>>> Jay
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> ath10k mailing list
>>>>>>>> ath10k@lists.infradead.org
>>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>>
>>>>>>>
>>>>>> Peter
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2016-07-10 17:44 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-07-08 4:52 Does 99x0 support mesh mode? Yu-Chieh
2016-07-08 17:15 ` Yeoh Chun-Yeow
2016-07-08 17:48 ` Peter Oh
2016-07-09 2:57 ` Yu-Chieh
2016-07-09 3:25 ` Yu-Chieh
2016-07-09 15:15 ` Yeoh Chun-Yeow
2016-07-09 15:58 ` Yu-Chieh
2016-07-09 16:26 ` Yeoh Chun-Yeow
2016-07-10 17:44 ` Yu-Chieh
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.