* [PATCH 1/3] sunxi: H3/H5 Sync DT files from upstream Linux kernel as of next-20200108
2020-01-12 15:36 [PATCH 0/3] sunxi: Sync H3/H5 DT and add ALL-H3-IT and ALL-H5-CC Chen-Yu Tsai
@ 2020-01-12 15:36 ` Chen-Yu Tsai
2020-01-21 7:32 ` Jagan Teki
2020-01-12 15:36 ` [PATCH 2/3] sunxi: Add Libre Computer ALL-H3-IT H5 board Chen-Yu Tsai
` (2 subsequent siblings)
3 siblings, 1 reply; 13+ messages in thread
From: Chen-Yu Tsai @ 2020-01-12 15:36 UTC (permalink / raw)
To: u-boot
From: Chen-Yu Tsai <wens@csie.org>
Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo
98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next
which is also part of next-20200108.
Changes brought in include:
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/dts/Makefile | 9 +-
.../dts/sun50i-h5-bananapi-m2-plus-v1.2.dts | 11 ++
.../sun50i-h5-emlid-neutis-n5-devboard.dts | 137 ++-----------
arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi | 95 +--------
.../arm/dts/sun50i-h5-libretech-all-h3-cc.dts | 10 +-
.../arm/dts/sun50i-h5-libretech-all-h3-it.dts | 11 ++
.../arm/dts/sun50i-h5-libretech-all-h5-cc.dts | 61 ++++++
arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts | 53 +----
arch/arm/dts/sun50i-h5-nanopi-neo2.dts | 45 +----
arch/arm/dts/sun50i-h5-orangepi-pc2.dts | 47 +----
arch/arm/dts/sun50i-h5-orangepi-prime.dts | 52 +----
arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts | 11 +-
.../arm/dts/sun50i-h5-orangepi-zero-plus2.dts | 46 +----
arch/arm/dts/sun50i-h5.dtsi | 186 +++++++++++++-----
.../dts/sun8i-h2-plus-bananapi-m2-zero.dts | 40 +++-
arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts | 2 -
arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts | 22 ++-
.../dts/sun8i-h3-bananapi-m2-plus-v1.2.dts | 13 ++
arch/arm/dts/sun8i-h3-beelink-x2.dts | 11 +-
.../sun8i-h3-emlid-neutis-n5h3-devboard.dts | 72 +++++++
arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi | 11 ++
arch/arm/dts/sun8i-h3-mapleboard-mp130.dts | 152 ++++++++++++++
arch/arm/dts/sun8i-h3-nanopi-duo2.dts | 173 ++++++++++++++++
arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts | 28 ++-
arch/arm/dts/sun8i-h3-nanopi-m1.dts | 2 +-
arch/arm/dts/sun8i-h3-nanopi-neo-air.dts | 2 +-
arch/arm/dts/sun8i-h3-nanopi.dtsi | 25 +--
arch/arm/dts/sun8i-h3-orangepi-2.dts | 34 +---
arch/arm/dts/sun8i-h3-orangepi-lite.dts | 27 +--
arch/arm/dts/sun8i-h3-orangepi-one.dts | 28 +--
arch/arm/dts/sun8i-h3-orangepi-pc.dts | 27 +--
arch/arm/dts/sun8i-h3-orangepi-plus.dts | 23 ++-
arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts | 2 +-
arch/arm/dts/sun8i-h3-rervision-dvk.dts | 114 +++++++++++
arch/arm/dts/sun8i-h3.dtsi | 86 +++++++-
arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi | 30 +++
arch/arm/dts/sunxi-bananapi-m2-plus.dtsi | 7 +-
arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi | 170 ++++++++++++++++
arch/arm/dts/sunxi-h3-h5.dtsi | 137 ++++++++-----
arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi | 65 +++++-
arch/arm/dts/sunxi-libretech-all-h3-it.dtsi | 180 +++++++++++++++++
include/dt-bindings/clock/sun8i-h3-ccu.h | 11 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
43 files changed, 1550 insertions(+), 723 deletions(-)
create mode 100644 arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts
create mode 100644 arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts
create mode 100644 arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts
create mode 100644 arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
create mode 100644 arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
create mode 100644 arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
create mode 100644 arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
create mode 100644 arch/arm/dts/sun8i-h3-nanopi-duo2.dts
create mode 100644 arch/arm/dts/sun8i-h3-rervision-dvk.dts
create mode 100644 arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
create mode 100644 arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi
create mode 100644 arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 983e235f4427..b89ed48e9a4e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -513,8 +513,12 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h2-plus-orangepi-r1.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
+ sun8i-h3-bananapi-m2-plus-v1.2.dtb \
sun8i-h3-beelink-x2.dtb \
+ sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
+ sun8i-h3-mapleboard-mp130.dtb \
+ sun8i-h3-nanopi-duo2.dtb \
sun8i-h3-nanopi-m1.dtb \
sun8i-h3-nanopi-m1-plus.dtb \
sun8i-h3-nanopi-neo.dtb \
@@ -526,7 +530,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h3-orangepi-pc-plus.dtb \
sun8i-h3-orangepi-plus.dtb \
sun8i-h3-orangepi-plus2e.dtb \
- sun8i-h3-orangepi-zero-plus2.dtb
+ sun8i-h3-orangepi-zero-plus2.dtb \
+ sun8i-h3-rervision-dvk.dtb
dtb-$(CONFIG_MACH_SUN8I_R40) += \
sun8i-r40-bananapi-m2-ultra.dtb \
sun8i-v40-bananapi-m2-berry.dtb
@@ -536,6 +541,8 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
sun50i-h5-bananapi-m2-plus.dtb \
sun50i-h5-emlid-neutis-n5-devboard.dtb \
sun50i-h5-libretech-all-h3-cc.dtb \
+ sun50i-h5-libretech-all-h3-it.dtb \
+ sun50i-h5-libretech-all-h5-cc.dtb \
sun50i-h5-nanopi-neo2.dtb \
sun50i-h5-nanopi-neo-plus2.dtb \
sun50i-h5-orangepi-zero-plus.dtb \
diff --git a/arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts b/arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts
new file mode 100644
index 000000000000..2e2b14c0ae75
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include <arm/sunxi-bananapi-m2-plus-v1.2.dtsi>
+
+/ {
+ model = "Banana Pi BPI-M2-Plus v1.2 H5";
+ compatible = "bananapi,bpi-m2-plus-v1.2", "allwinner,sun50i-h5";
+};
diff --git a/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts b/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts
index 493947c9b14a..076a0b983101 100644
--- a/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts
+++ b/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts
@@ -1,43 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
+
/*
- * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This library is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This library is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ * DTS for Emlid Neutis N5 Dev board.
*/
/dts-v1/;
@@ -46,17 +11,9 @@
/ {
model = "Emlid Neutis N5 Developer board";
- compatible = "emlid,emlid-neutis-n5-devboard",
- "emlid,emlid-neutis-n5",
- "allwinner,sun50i-h5";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
+ compatible = "emlid,neutis-n5-devboard",
+ "emlid,neutis-n5",
+ "allwinner,sun50i-h5";
connector {
compatible = "hdmi-connector";
@@ -69,19 +26,8 @@
};
};
- reg_usb0_vbus: usb0-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb0-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
- status = "okay";
- };
-
vdd_cpux: gpio-regulator {
compatible = "regulator-gpio";
- pinctrl-names = "default";
regulator-name = "vdd-cpux";
regulator-type = "voltage";
regulator-boot-on;
@@ -91,54 +37,15 @@
regulator-ramp-delay = <50>; /* 4ms */
gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
gpios-states = <0x1>;
- states = <1100000 0x0
- 1300000 0x1>;
+ states = <1100000 0>, <1300000 1>;
};
};
-&codec {
- allwinner,audio-routing =
- "Line Out", "LINEOUT",
- "LINEIN", "Line In",
- "MIC1", "Mic",
- "MIC2", "Mic",
- "Mic", "MBIAS";
- status = "okay";
-};
-
-&de {
- status = "okay";
-};
-
-&ehci0 {
- status = "okay";
+&cpu0 {
+ cpu-supply = <&vdd_cpux>;
};
-&ehci1 {
- status = "okay";
-};
-
-&ehci2 {
- status = "okay";
-};
-
-&ehci3 {
- status = "okay";
-};
-
-&ohci0 {
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
-};
-
-&ohci2 {
- status = "okay";
-};
-
-&ohci3 {
+&codec {
status = "okay";
};
@@ -159,26 +66,6 @@
};
};
-&mmc0 {
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
- status = "okay";
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usbphy {
- usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
- usb0_vbus-supply = <®_usb0_vbus>;
+&i2c1 {
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi b/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi
index 8e1e37db27d6..6db485584333 100644
--- a/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi
+++ b/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi
@@ -1,96 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
+
/*
- * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This library is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This library is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ * DTSI for Emlid Neutis N5 SoM.
*/
/dts-v1/;
#include "sun50i-h5.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- wifi_pwrseq: wifi_pwrseq {
- compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
- post-power-on-delay-ms = <200>;
- };
-};
-
-&mmc1 {
- vmmc-supply = <®_vcc3v3>;
- vqmmc-supply = <®_vcc3v3>;
- mmc-pwrseq = <&wifi_pwrseq>;
- bus-width = <4>;
- non-removable;
- status = "okay";
-
- brcmf: wifi at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- interrupt-parent = <&r_pio>;
- interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>; /* PL5 */
- interrupt-names = "host-wake";
- };
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <8>;
- non-removable;
- cap-mmc-hw-reset;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
- status = "okay";
-};
+#include <sunxi-h3-h5-emlid-neutis.dtsi>
diff --git a/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts b/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts
index a35f77de22d8..a91806618e6f 100644
--- a/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts
+++ b/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts
@@ -1,8 +1,6 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2018 BayLibre, SAS
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- */
+// Copyright (C) 2018 BayLibre, SAS
+// Author: Neil Armstrong <narmstrong@baylibre.com>
/dts-v1/;
#include "sun50i-h5.dtsi"
@@ -12,3 +10,7 @@
model = "Libre Computer Board ALL-H3-CC H5";
compatible = "libretech,all-h3-cc-h5", "allwinner,sun50i-h5";
};
+
+&mmc2 {
+ mmc-ddr-3_3v;
+};
diff --git a/arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts b/arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts
new file mode 100644
index 000000000000..f6756d1bb057
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2019 Chen-Yu Tsai <wens@csie.org>
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include <sunxi-libretech-all-h3-it.dtsi>
+
+/ {
+ model = "Libre Computer Board ALL-H3-IT H5";
+ compatible = "libretech,all-h3-it-h5", "allwinner,sun50i-h5";
+};
diff --git a/arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts b/arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts
new file mode 100644
index 000000000000..df1b9263ad0e
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Chen-Yu Tsai <wens@csie.org>
+
+#include "sun50i-h5-libretech-all-h3-cc.dts"
+
+/ {
+ model = "Libre Computer Board ALL-H5-CC H5";
+ compatible = "libretech,all-h5-cc-h5", "allwinner,sun50i-h5";
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <5000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <®_vcc5v0>;
+ };
+};
+
+&codec {
+ /* No line out; only onboard microphone */
+ allwinner,audio-routing =
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+};
+
+/* This board has external PHY */
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ /delete-property/ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+};
diff --git a/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts
index 506e25ba028a..4f9ba53ffaae 100644
--- a/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts
+++ b/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts
@@ -1,45 +1,6 @@
-/*
- * Copyright (C) 2017 Antony Antony <antony@phenome.org>
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Antony Antony <antony@phenome.org>
+// Copyright (C) 2016 ARM Ltd.
/dts-v1/;
#include "sun50i-h5.dtsi"
@@ -78,7 +39,6 @@
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
@@ -96,7 +56,6 @@
vdd_cpux: gpio-regulator {
compatible = "regulator-gpio";
- pinctrl-names = "default";
regulator-name = "vdd-cpux";
regulator-type = "voltage";
regulator-boot-on;
@@ -106,13 +65,11 @@
regulator-ramp-delay = <50>; /* 4ms */
gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
gpios-states = <0x1>;
- states = <1100000 0x0
- 1300000 0x1>;
+ states = <1100000 0>, <1300000 1>;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
post-power-on-delay-ms = <200>;
};
@@ -191,7 +148,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5-nanopi-neo2.dts b/arch/arm/dts/sun50i-h5-nanopi-neo2.dts
index cc268a69786c..b059e20813bd 100644
--- a/arch/arm/dts/sun50i-h5-nanopi-neo2.dts
+++ b/arch/arm/dts/sun50i-h5-nanopi-neo2.dts
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
/dts-v1/;
#include "sun50i-h5.dtsi"
@@ -142,7 +103,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts
index 3e0d5a9c096d..70b5f0998421 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2016 ARM Ltd.
/dts-v1/;
#include "sun50i-h5.dtsi"
@@ -180,7 +141,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -221,7 +182,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5-orangepi-prime.dts b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
index b75ca4d7d001..cb44bfa5981f 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
@@ -1,47 +1,7 @@
-/*
- * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
- *
- * Based on sun50i-h5-orangepi-pc2.dts, which is:
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+// Based on sun50i-h5-orangepi-pc2.dts, which is:
+// Copyright (C) 2016 ARM Ltd.
/dts-v1/;
#include "sun50i-h5.dtsi"
@@ -187,7 +147,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -224,7 +184,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
index 1238de25a969..ef5ca6444220 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
@@ -1,9 +1,6 @@
-/*
- * Copyright (C) 2016 ARM Ltd.
- * Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de>
- *
- * SPDX-License-Identifier: (GPL-2.0+ OR X11)
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2016 ARM Ltd.
+// Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de>
/dts-v1/;
#include "sun50i-h5.dtsi"
@@ -127,7 +124,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts
index 53c8c11620e0..c95a68541309 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This library is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This library is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
/dts-v1/;
@@ -78,7 +39,6 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
post-power-on-delay-ms = <200>;
};
@@ -134,7 +94,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-h5.dtsi b/arch/arm/dts/sun50i-h5.dtsi
index 4e4738cab001..3a1c8b2efd69 100644
--- a/arch/arm/dts/sun50i-h5.dtsi
+++ b/arch/arm/dts/sun50i-h5.dtsi
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2016 ARM Ltd.
#include <sunxi-h3-h5.dtsi>
@@ -48,34 +9,44 @@
#size-cells = <0>;
cpu0: cpu at 0 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <0>;
enable-method = "psci";
};
- cpu at 1 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ cpu1: cpu at 1 {
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <1>;
enable-method = "psci";
};
- cpu at 2 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ cpu2: cpu at 2 {
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <2>;
enable-method = "psci";
};
- cpu at 3 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ cpu3: cpu at 3 {
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <3>;
enable-method = "psci";
};
};
+ pmu {
+ compatible = "arm,cortex-a53-pmu",
+ "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
psci {
compatible = "arm,psci-0.2";
method = "smc";
@@ -92,6 +63,117 @@
<GIC_PPI 10
(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
+
+ soc {
+ syscon: system-control at 1c00000 {
+ compatible = "allwinner,sun50i-h5-system-control";
+ reg = <0x01c00000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c1: sram at 18000 {
+ compatible = "mmio-sram";
+ reg = <0x00018000 0x1c000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00018000 0x1c000>;
+
+ ve_sram: sram-section at 0 {
+ compatible = "allwinner,sun50i-h5-sram-c1",
+ "allwinner,sun4i-a10-sram-c1";
+ reg = <0x000000 0x1c000>;
+ };
+ };
+ };
+
+ video-codec at 1c0e000 {
+ compatible = "allwinner,sun50i-h5-video-engine";
+ reg = <0x01c0e000 0x1000>;
+ clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+ <&ccu CLK_DRAM_VE>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_BUS_VE>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ allwinner,sram = <&ve_sram 1>;
+ };
+
+ crypto: crypto at 1c15000 {
+ compatible = "allwinner,sun50i-h5-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_CE>;
+ };
+
+ mali: gpu at 1e80000 {
+ compatible = "allwinner,sun50i-h5-mali", "arm,mali-450";
+ reg = <0x01e80000 0x30000>;
+ /*
+ * While the datasheet lists an interrupt for the
+ * PMU, the actual silicon does not have the PMU
+ * block. Reads all return zero, and writes are
+ * ignored.
+ */
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gp",
+ "gpmmu",
+ "pp",
+ "pp0",
+ "ppmmu0",
+ "pp1",
+ "ppmmu1",
+ "pp2",
+ "ppmmu2",
+ "pp3",
+ "ppmmu3",
+ "pmu";
+ clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
+ clock-names = "bus", "core";
+ resets = <&ccu RST_BUS_GPU>;
+
+ assigned-clocks = <&ccu CLK_GPU>;
+ assigned-clock-rates = <384000000>;
+ };
+
+ ths: thermal-sensor at 1c25000 {
+ compatible = "allwinner,sun50i-h5-ths";
+ reg = <0x01c25000 0x400>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&ccu RST_BUS_THS>;
+ clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+ clock-names = "bus", "mod";
+ nvmem-cells = <&ths_calibration>;
+ nvmem-cell-names = "calibration";
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 0>;
+ };
+
+ gpu_thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 1>;
+ };
+ };
};
&ccu {
@@ -129,3 +211,11 @@
<GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
compatible = "allwinner,sun50i-h5-pinctrl";
};
+
+&rtc {
+ compatible = "allwinner,sun50i-h5-rtc";
+};
+
+&sid {
+ compatible = "allwinner,sun50i-h5-sid";
+};
diff --git a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index 7d01f9322658..d277d043031b 100644
--- a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -28,7 +28,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
pwr_led {
label = "bananapi-m2-zero:red:pwr";
@@ -39,7 +38,6 @@
gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
sw4 {
label = "power";
@@ -48,13 +46,34 @@
};
};
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+ enable-active-high;
+ gpios-states = <0x1>;
+ states = <1100000 0>, <1300000 1>;
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
};
};
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
&ehci0 {
status = "okay";
};
@@ -94,14 +113,27 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ uart-has-rtscts;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rtc 1>;
+ clock-names = "lpo";
+ vbat-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+ host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+ shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ };
+
};
&usb_otg {
diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
index c652ac3b712c..3356f4210d45 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
@@ -68,7 +68,6 @@
};
};
-/*
&spi0 {
status = "okay";
@@ -76,7 +75,6 @@
compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
};
};
-*/
&ohci1 {
/*
diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
index 0bc031fe4c56..f19ed981da9d 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -89,6 +89,22 @@
gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
};
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ enable-active-high;
+ gpios-states = <1>;
+ states = <1100000 0>, <1300000 1>;
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
@@ -96,6 +112,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
&ehci0 {
status = "okay";
};
@@ -157,7 +177,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts b/arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
new file mode 100644
index 000000000000..fc4a8c3d084d
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-bananapi-m2-plus-v1.2.dtsi"
+
+/ {
+ model = "Banana Pi BPI-M2-Plus v1.2 H3";
+ compatible = "bananapi,bpi-m2-plus-v1.2", "allwinner,sun8i-h3";
+};
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts
index 25540b7694d5..45a24441ff18 100644
--- a/arch/arm/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -90,6 +90,8 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
};
sound_spdif {
@@ -141,8 +143,9 @@
};
&ir {
+ linux,rc-map-name = "rc-tanix-tx3mini";
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -155,6 +158,8 @@
&mmc1 {
vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
@@ -193,13 +198,13 @@
&spdif {
pinctrl-names = "default";
- pinctrl-0 = <&spdif_tx_pins_a>;
+ pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
new file mode 100644
index 000000000000..02fbe00cde97
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTS for Emlid Neutis N5 Dev board.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgiii.staroselskii@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3-emlid-neutis-n5h3.dtsi"
+
+/ {
+ model = "Emlid Neutis N5H3 Developer board";
+ compatible = "emlid,neutis-n5h3-devboard",
+ "emlid,neutis-n5h3",
+ "allwinner,sun8i-h3";
+
+ vdd_cpux: gpio-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ gpios-states = <0x1>;
+ states = <1100000 0x0>, <1300000 0x1>;
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpux>;
+};
+
+&codec {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
new file mode 100644
index 000000000000..3f5c63e582bf
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis N5 SoM.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3.dtsi"
+#include <sunxi-h3-h5-emlid-neutis.dtsi>
diff --git a/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts b/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
new file mode 100644
index 000000000000..ff0a7a952e0c
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Centrum Embedded Systems, Jia-Bin Huang <jb@ces.com.tw>
+ * Copyright (C) 2018 Jonathan McDowell <noodles@earth.li>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "MapleBoard MP130";
+ compatible = "mapleboard,mp130", "allwinner,sun8i-h3";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "mp130:orange:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "mp130:orange:status";
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+ };
+
+ user {
+ label = "user";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "LINEIN", "Line In";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_ir_rx_pin>;
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/dts/sun8i-h3-nanopi-duo2.dts
new file mode 100644
index 000000000000..6b149271ef13
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-nanopi-duo2.dts
@@ -0,0 +1,173 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Karl Palsson <karlp@tweak.net.au>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "FriendlyARM NanoPi Duo2";
+ compatible = "friendlyarm,nanopi-duo2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "nanopi:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+
+ status {
+ label = "nanopi:green:status";
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+
+ k1 {
+ label = "k1";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+ };
+ };
+
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ enable-active-high;
+ enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ gpios-states = <0x1>;
+ states = <1100000 0>, <1300000 1>;
+ };
+
+ reg_vcc_dram: vcc-dram {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-dram";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+ vin-supply = <®_vcc5v0>;
+ };
+
+ reg_vdd_sys: vdd-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-sys";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ vin-supply = <®_vcc5v0>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ };
+
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+ vmmc-supply = <®_vcc3v3>;
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: sdio_wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>, <&uart2_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rtc 1>;
+ clock-names = "lpo";
+ vbat-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+ shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+ };
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "otg";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
index 65cba1050802..4ba533b0340f 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -64,9 +64,23 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci1 {
@@ -94,9 +108,19 @@
};
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/dts/sun8i-h3-nanopi-m1.dts
index 9412668bb888..69243dcb30a6 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-m1.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-m1.dts
@@ -93,7 +93,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
index 6246d3eff39d..07867a0d569b 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
@@ -105,7 +105,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-nanopi.dtsi b/arch/arm/dts/sun8i-h3-nanopi.dtsi
index f110ee382239..4df29a65316d 100644
--- a/arch/arm/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/dts/sun8i-h3-nanopi.dtsi
@@ -59,8 +59,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_npi>, <&leds_r_npi>;
status {
label = "nanopi:blue:status";
@@ -78,8 +76,6 @@
r_gpio_keys {
compatible = "gpio-keys";
input-name = "k1";
- pinctrl-names = "default";
- pinctrl-0 = <&sw_r_npi>;
k1 {
label = "k1";
@@ -104,28 +100,9 @@
status = "okay";
};
-&pio {
- leds_npi: led_pins {
- pins = "PA10";
- function = "gpio_out";
- };
-};
-
-&r_pio {
- leds_r_npi: led_pins {
- pins = "PL10";
- function = "gpio_out";
- };
-
- sw_r_npi: key_pins {
- pins = "PL3";
- function = "gpio_in";
- };
-};
-
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index f1fc6bdca8be..597c425d08ec 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -75,8 +75,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
status_led {
label = "orangepi:red:status";
@@ -92,8 +90,6 @@
r_gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&sw_r_opc>;
sw2 {
label = "sw2";
@@ -110,8 +106,6 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
};
};
@@ -152,7 +146,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -179,30 +173,6 @@
};
};
-&pio {
- leds_opc: led_pins {
- pins = "PA15";
- function = "gpio_out";
- };
-};
-
-&r_pio {
- leds_r_opc: led_pins {
- pins = "PL10";
- function = "gpio_out";
- };
-
- sw_r_opc: key_pins {
- pins = "PL3", "PL4";
- function = "gpio_in";
- };
-
- wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
- pins = "PL7";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
status = "okay";
@@ -210,7 +180,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/dts/sun8i-h3-orangepi-lite.dts
index 476ae8e387ca..6f9c97add54e 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-lite.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-lite.dts
@@ -74,8 +74,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
pwr_led {
label = "orangepi:green:pwr";
@@ -91,8 +89,6 @@
r_gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&sw_r_opc>;
sw4 {
label = "sw4";
@@ -126,7 +122,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -160,28 +156,9 @@
status = "okay";
};
-&pio {
- leds_opc: led_pins {
- pins = "PA15";
- function = "gpio_out";
- };
-};
-
-&r_pio {
- leds_r_opc: led_pins {
- pins = "PL10";
- function = "gpio_out";
- };
-
- sw_r_opc: key_pins {
- pins = "PL3";
- function = "gpio_in";
- };
-};
-
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-one.dts b/arch/arm/dts/sun8i-h3-orangepi-one.dts
index 245fd658defb..4759ba3f2986 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-one.dts
@@ -73,8 +73,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
pwr_led {
label = "orangepi:green:pwr";
@@ -90,8 +88,6 @@
r_gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&sw_r_opc>;
sw4 {
label = "sw4";
@@ -113,8 +109,7 @@
gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
enable-active-high;
gpios-states = <0x1>;
- states = <1100000 0x0
- 1300000 0x1>;
+ states = <1100000 0>, <1300000 1>;
};
};
@@ -166,25 +161,6 @@
status = "okay";
};
-&pio {
- leds_opc: led_pins {
- pins = "PA15";
- function = "gpio_out";
- };
-};
-
-&r_pio {
- leds_r_opc: led_pins {
- pins = "PL10";
- function = "gpio_out";
- };
-
- sw_r_opc: key_pins {
- pins = "PL3";
- function = "gpio_in";
- };
-};
-
®_usb0_vbus {
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
status = "okay";
@@ -192,7 +168,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
index 46240334128f..5aff8ecc66cb 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
@@ -73,8 +73,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
pwr_led {
label = "orangepi:green:pwr";
@@ -90,8 +88,6 @@
r_gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&sw_r_opc>;
sw4 {
label = "sw4";
@@ -152,7 +148,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -179,13 +175,6 @@
status = "okay";
};
-&pio {
- leds_opc: led_pins {
- pins = "PA15";
- function = "gpio_out";
- };
-};
-
&r_i2c {
status = "okay";
@@ -210,18 +199,6 @@
};
};
-&r_pio {
- leds_r_opc: led_pins {
- pins = "PL10";
- function = "gpio_out";
- };
-
- sw_r_opc: key_pins {
- pins = "PL3";
- function = "gpio_in";
- };
-};
-
®_usb0_vbus {
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
status = "okay";
@@ -229,7 +206,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/dts/sun8i-h3-orangepi-plus.dts
index b403e5d787cb..97f497854e05 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-plus.dts
@@ -63,8 +63,6 @@
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&usb3_vbus_pin_a>;
regulator-name = "usb3-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
@@ -74,6 +72,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
&ehci3 {
status = "okay";
};
@@ -112,10 +114,19 @@
bias-pull-up;
};
-&pio {
- usb3_vbus_pin_a: usb3_vbus_pin {
- pins = "PG11";
- function = "gpio_out";
+&r_i2c {
+ status = "okay";
+
+ reg_vdd_cpux: regulator at 65 {
+ compatible = "silergy,sy8106a";
+ reg = <0x65>;
+ regulator-name = "vdd-cpux";
+ silergy,fixed-microvolt = <1200000>;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <200>;
+ regulator-boot-on;
+ regulator-always-on;
};
};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
index f2f7b7a92571..b8f46e2802fd 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
@@ -134,6 +134,6 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/dts/sun8i-h3-rervision-dvk.dts
new file mode 100644
index 000000000000..4738f3a9efe4
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-rervision-dvk.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Bootlin
+ * Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "RerVision H3-DVK";
+ compatible = "rervision,h3-dvk", "allwinner,sun8i-h3";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+ vmmc-supply = <®_vcc3v3>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usbphy {
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3.dtsi b/arch/arm/dts/sun8i-h3.dtsi
index f0096074a467..20217e2ca4d3 100644
--- a/arch/arm/dts/sun8i-h3.dtsi
+++ b/arch/arm/dts/sun8i-h3.dtsi
@@ -47,19 +47,19 @@
compatible = "operating-points-v2";
opp-shared;
- opp at 648000000 {
+ opp-648000000 {
opp-hz = /bits/ 64 <648000000>;
opp-microvolt = <1040000 1040000 1300000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
- opp at 816000000 {
+ opp-816000000 {
opp-hz = /bits/ 64 <816000000>;
opp-microvolt = <1100000 1100000 1300000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
- opp at 1008000000 {
+ opp-1008000000 {
opp-hz = /bits/ 64 <1008000000>;
opp-microvolt = <1200000 1200000 1300000>;
clock-latency-ns = <244144>; /* 8 32k periods */
@@ -80,7 +80,7 @@
#cooling-cells = <2>;
};
- cpu at 1 {
+ cpu1: cpu at 1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <1>;
@@ -90,7 +90,7 @@
#cooling-cells = <2>;
};
- cpu at 2 {
+ cpu2: cpu at 2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <2>;
@@ -100,7 +100,7 @@
#cooling-cells = <2>;
};
- cpu at 3 {
+ cpu3: cpu at 3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <3>;
@@ -111,6 +111,15 @@
};
};
+ pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -120,9 +129,22 @@
};
soc {
- system-control at 1c00000 {
+ deinterlace: deinterlace at 1400000 {
+ compatible = "allwinner,sun8i-h3-deinterlace";
+ reg = <0x01400000 0x20000>;
+ clocks = <&ccu CLK_BUS_DEINTERLACE>,
+ <&ccu CLK_DEINTERLACE>,
+ <&ccu CLK_DRAM_DEINTERLACE>;
+ clock-names = "bus", "mod", "ram";
+ resets = <&ccu RST_BUS_DEINTERLACE>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&mbus 9>;
+ interconnect-names = "dma-mem";
+ };
+
+ syscon: system-control at 1c00000 {
compatible = "allwinner,sun8i-h3-system-control";
- reg = <0x01c00000 0x30>;
+ reg = <0x01c00000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
@@ -142,6 +164,26 @@
};
};
+ video-codec at 1c0e000 {
+ compatible = "allwinner,sun8i-h3-video-engine";
+ reg = <0x01c0e000 0x1000>;
+ clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+ <&ccu CLK_DRAM_VE>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_BUS_VE>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ allwinner,sram = <&ve_sram 1>;
+ };
+
+ crypto: crypto at 1c15000 {
+ compatible = "allwinner,sun8i-h3-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_CE>;
+ };
+
mali: gpu at 1c40000 {
compatible = "allwinner,sun8i-h3-mali", "arm,mali-400";
reg = <0x01c40000 0x10000>;
@@ -166,6 +208,26 @@
assigned-clocks = <&ccu CLK_GPU>;
assigned-clock-rates = <384000000>;
};
+
+ ths: thermal-sensor at 1c25000 {
+ compatible = "allwinner,sun8i-h3-ths";
+ reg = <0x01c25000 0x400>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&ccu RST_BUS_THS>;
+ clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+ clock-names = "bus", "mod";
+ nvmem-cells = <&ths_calibration>;
+ nvmem-cell-names = "calibration";
+ #thermal-sensor-cells = <0>;
+ };
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 0>;
+ };
};
};
@@ -216,3 +278,11 @@
&pio {
compatible = "allwinner,sun8i-h3-pinctrl";
};
+
+&rtc {
+ compatible = "allwinner,sun8i-h3-rtc";
+};
+
+&sid {
+ compatible = "allwinner,sun8i-h3-sid";
+};
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
new file mode 100644
index 000000000000..22466afd38a3
--- /dev/null
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+ */
+
+#include "sunxi-bananapi-m2-plus.dtsi"
+
+/ {
+ /*
+ * Bananapi M2+ v1.2 uses a GPIO line to change the effective
+ * resistance on the CPU regulator's feedback pin.
+ */
+ reg_vdd_cpux: vdd-cpux {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+ gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+ gpios-states = <0x1>;
+ states = <1100000 0>, <1300000 1>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
index 3bed375b9c03..39263e74fbb5 100644
--- a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
@@ -69,7 +69,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
pwr_led {
label = "bananapi-m2-plus:red:pwr";
@@ -80,7 +79,6 @@
gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
sw4 {
label = "power";
@@ -101,7 +99,6 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc 1>;
clock-names = "ext_clock";
@@ -153,7 +150,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -210,7 +207,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi b/arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi
new file mode 100644
index 000000000000..fc67e30fe212
--- /dev/null
+++ b/arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis SoMs.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii@emlid.com>
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
+ post-power-on-delay-ms = <200>;
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpux>;
+};
+
+®_usb0_vbus {
+ gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+ status = "okay";
+};
+
+
+&de {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>; /* PL5 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rtc 1>;
+ clock-names = "lpo";
+ vbat-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ shutdown-gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */
+ device-wakeup-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "LINEIN", "Line In",
+ "MIC1", "Mic",
+ "MIC2", "Mic",
+ "Mic", "MBIAS";
+};
+
+&i2c0 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi
index fc6131315c47..5e9c3060aa08 100644
--- a/arch/arm/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/dts/sunxi-h3-h5.dtsi
@@ -86,6 +86,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -93,15 +94,8 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- iosc: internal-osc-clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <16000000>;
- clock-accuracy = <300000000>;
- clock-output-names = "iosc";
+ clock-accuracy = <50000>;
+ clock-output-names = "ext_osc32k";
};
};
@@ -115,15 +109,16 @@
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
+ dma-ranges;
ranges;
display_clocks: clock at 1000000 {
/* compatible is in per SoC .dtsi file */
reg = <0x01000000 0x100000>;
- clocks = <&ccu CLK_DE>,
- <&ccu CLK_BUS_DE>;
- clock-names = "mod",
- "bus";
+ clocks = <&ccu CLK_BUS_DE>,
+ <&ccu CLK_DE>;
+ clock-names = "bus",
+ "mod";
resets = <&ccu RST_BUS_DE>;
#clock-cells = <1>;
#reset-cells = <1>;
@@ -152,12 +147,6 @@
};
};
- syscon: syscon at 1c00000 {
- compatible = "allwinner,sun8i-h3-system-controller",
- "syscon";
- reg = <0x01c00000 0x1000>;
- };
-
dma: dma-controller at 1c02000 {
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
@@ -239,6 +228,17 @@
#size-cells = <0>;
};
+ sid: eeprom at 1c14000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x1c14000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ths_calibration: thermal-sensor-calibration at 34 {
+ reg = <0x34 4>;
+ };
+ };
+
usb_otg: usb at 1c19000 {
compatible = "allwinner,sun8i-h3-musb";
reg = <0x01c19000 0x400>;
@@ -249,6 +249,7 @@
phys = <&usbphy 0>;
phy-names = "usb";
extcon = <&usbphy 0>;
+ dr_mode = "otg";
status = "disabled";
};
@@ -375,7 +376,7 @@
ccu: clock at 1c20000 {
/* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
@@ -386,14 +387,21 @@
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
- emac_rgmii_pins: emac0 {
+ csi_pins: csi-pins {
+ pins = "PE0", "PE2", "PE3", "PE4", "PE5",
+ "PE6", "PE7", "PE8", "PE9", "PE10",
+ "PE11";
+ function = "csi";
+ };
+
+ emac_rgmii_pins: emac-rgmii-pins {
pins = "PD0", "PD1", "PD2", "PD3", "PD4",
"PD5", "PD7", "PD8", "PD9", "PD10",
"PD12", "PD13", "PD15", "PD16", "PD17";
@@ -401,22 +409,22 @@
drive-strength = <40>;
};
- i2c0_pins: i2c0 {
+ i2c0_pins: i2c0-pins {
pins = "PA11", "PA12";
function = "i2c0";
};
- i2c1_pins: i2c1 {
+ i2c1_pins: i2c1-pins {
pins = "PA18", "PA19";
function = "i2c1";
};
- i2c2_pins: i2c2 {
+ i2c2_pins: i2c2-pins {
pins = "PE12", "PE13";
function = "i2c2";
};
- mmc0_pins: mmc0 {
+ mmc0_pins: mmc0-pins {
pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
function = "mmc0";
@@ -424,7 +432,7 @@
bias-pull-up;
};
- mmc1_pins: mmc1 {
+ mmc1_pins: mmc1-pins {
pins = "PG0", "PG1", "PG2", "PG3",
"PG4", "PG5";
function = "mmc1";
@@ -432,7 +440,7 @@
bias-pull-up;
};
- mmc2_8bit_pins: mmc2_8bit {
+ mmc2_8bit_pins: mmc2-8bit-pins {
pins = "PC5", "PC6", "PC8",
"PC9", "PC10", "PC11",
"PC12", "PC13", "PC14",
@@ -442,54 +450,59 @@
bias-pull-up;
};
- spdif_tx_pins_a: spdif {
+ spdif_tx_pin: spdif-tx-pin {
pins = "PA17";
function = "spdif";
};
- spi0_pins: spi0 {
+ spi0_pins: spi0-pins {
pins = "PC0", "PC1", "PC2", "PC3";
function = "spi0";
};
- spi1_pins: spi1 {
+ spi1_pins: spi1-pins {
pins = "PA15", "PA16", "PA14", "PA13";
function = "spi1";
};
- uart0_pins_a: uart0 {
+ uart0_pa_pins: uart0-pa-pins {
pins = "PA4", "PA5";
function = "uart0";
};
- uart1_pins: uart1 {
+ uart1_pins: uart1-pins {
pins = "PG6", "PG7";
function = "uart1";
};
- uart1_rts_cts_pins: uart1_rts_cts {
+ uart1_rts_cts_pins: uart1-rts-cts-pins {
pins = "PG8", "PG9";
function = "uart1";
};
- uart2_pins: uart2 {
+ uart2_pins: uart2-pins {
pins = "PA0", "PA1";
function = "uart2";
};
- uart3_pins: uart3 {
+ uart2_rts_cts_pins: uart2-rts-cts-pins {
+ pins = "PA2", "PA3";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3-pins {
pins = "PA13", "PA14";
function = "uart3";
};
- uart3_rts_cts_pins: uart3_rts_cts {
+ uart3_rts_cts_pins: uart3-rts-cts-pins {
pins = "PA15", "PA16";
function = "uart3";
};
};
timer at 1c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
+ compatible = "allwinner,sun8i-a23-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
@@ -543,6 +556,14 @@
};
};
+ mbus: dram-controller at 1c62000 {
+ compatible = "allwinner,sun8i-h3-mbus";
+ reg = <0x01c62000 0x1000>;
+ clocks = <&ccu CLK_MBUS>;
+ dma-ranges = <0x00000000 0x40000000 0xc0000000>;
+ #interconnect-cells = <1>;
+ };
+
spi0: spi at 1c68000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>;
@@ -579,6 +600,7 @@
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
};
spdif: spdif at 1c21000 {
@@ -744,6 +766,20 @@
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ csi: camera at 1cb0000 {
+ compatible = "allwinner,sun8i-h3-csi";
+ reg = <0x01cb0000 0x1000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CSI>,
+ <&ccu CLK_CSI_SCLK>,
+ <&ccu CLK_DRAM_CSI>;
+ clock-names = "bus", "mod", "ram";
+ resets = <&ccu RST_BUS_CSI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&csi_pins>;
+ status = "disabled";
+ };
+
hdmi: hdmi at 1ee0000 {
compatible = "allwinner,sun8i-h3-dw-hdmi",
"allwinner,sun8i-a83t-dw-hdmi";
@@ -756,7 +792,7 @@
resets = <&ccu RST_BUS_HDMI1>;
reset-names = "ctrl";
phys = <&hdmi_phy>;
- phy-names = "hdmi-phy";
+ phy-names = "phy";
status = "disabled";
ports {
@@ -781,7 +817,7 @@
compatible = "allwinner,sun8i-h3-hdmi-phy";
reg = <0x01ef0000 0x10000>;
clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
- <&ccu 6>;
+ <&ccu CLK_PLL_VIDEO>;
clock-names = "bus", "mod", "pll-0";
resets = <&ccu RST_BUS_HDMI0>;
reset-names = "phy";
@@ -789,17 +825,20 @@
};
rtc: rtc at 1f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01f00000 0x400>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clock-output-names = "osc32k", "osc32k-out", "iosc";
+ clocks = <&osc32k>;
+ #clock-cells = <1>;
};
r_ccu: clock at 1f01400 {
compatible = "allwinner,sun8i-h3-r-ccu";
reg = <0x01f01400 0x100>;
- clocks = <&osc24M>, <&osc32k>, <&iosc>,
- <&ccu 9>;
+ clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+ <&ccu CLK_PLL_PERIPH0>;
clock-names = "hosc", "losc", "iosc", "pll-periph";
#clock-cells = <1>;
#reset-cells = <1>;
@@ -811,12 +850,12 @@
};
ir: ir at 1f02000 {
- compatible = "allwinner,sun5i-a13-ir";
+ compatible = "allwinner,sun6i-a31-ir";
clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
clock-names = "apb", "ir";
resets = <&r_ccu RST_APB0_IR>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
+ reg = <0x01f02000 0x400>;
status = "disabled";
};
@@ -837,19 +876,19 @@
compatible = "allwinner,sun8i-h3-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
- ir_pins_a: ir {
+ r_ir_rx_pin: r-ir-rx-pin {
pins = "PL11";
function = "s_cir_rx";
};
- r_i2c_pins: r-i2c {
+ r_i2c_pins: r-i2c-pins {
pins = "PL0", "PL1";
function = "s_i2c";
};
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
index 14c8ec16d47e..19b3b23cfaa8 100644
--- a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
@@ -16,6 +16,17 @@
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -44,8 +55,8 @@
reg_vcc1v2: vcc1v2 {
compatible = "regulator-fixed";
regulator-name = "vcc1v2";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <®_vcc5v0>;
@@ -95,8 +106,8 @@
reg_vdd_cpux: vdd-cpux {
compatible = "regulator-fixed";
regulator-name = "vdd-cpux";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <®_vcc5v0>;
@@ -105,6 +116,26 @@
};
};
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
@@ -124,17 +155,26 @@
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
&mmc0 {
vmmc-supply = <®_vcc_io>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
@@ -147,6 +187,10 @@
status = "okay";
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
@@ -161,7 +205,12 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
status = "okay";
};
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
new file mode 100644
index 000000000000..204fba3614f9
--- /dev/null
+++ b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2019 Chen-Yu Tsai <wens@csie.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ spi0 = &spi0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "d";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status_led {
+ label = "librecomputer:blue:status";
+ gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+ };
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <®_vcc5v0>;
+ };
+
+ /* This represents the board's 5V input */
+ reg_vcc5v0: vcc5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_vcc_dram: vcc-dram {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-dram";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <®_vcc5v0>;
+ gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+ enable-active-high;
+ };
+
+ reg_vcc_io: vcc-io {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-io";
+ /* This is simply a MOSFET switch */
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <®_vcc3v3>;
+ gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+ };
+
+ reg_vcc_usbwifi: vcc-usbwifi {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-usbwifi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_vcc5v0>;
+ gpio = <&pio 6 4 GPIO_ACTIVE_HIGH>; /* PG4 */
+ enable-active-high;
+ };
+
+ reg_vdd_cpux: vdd-cpux {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-cpux";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <®_vcc5v0>;
+ gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ enable-active-high;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu1 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu2 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&cpu3 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc_io>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&pio {
+ vcc-pa-supply = <®_vcc_io>;
+ vcc-pc-supply = <®_vcc_io>;
+ vcc-pd-supply = <®_vcc_io>;
+ vcc-pe-supply = <®_vcc_io>;
+ vcc-pf-supply = <®_vcc_io>;
+ vcc-pg-supply = <®_vcc_io>;
+};
+
+&r_pio {
+ vcc-pl-supply = <®_vcc3v3>;
+};
+
+&spi0 {
+ status = "okay";
+
+ spiflash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc_usbwifi>;
+ status = "okay";
+};
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
index efb7ba2bd515..30d2d15373a2 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -43,6 +43,10 @@
#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
#define _DT_BINDINGS_CLK_SUN8I_H3_H_
+#define CLK_PLL_VIDEO 6
+
+#define CLK_PLL_PERIPH0 9
+
#define CLK_CPUX 14
#define CLK_BUS_CE 20
@@ -91,7 +95,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -139,7 +143,10 @@
#define CLK_AVS 110
#define CLK_HDMI 111
#define CLK_HDMI_DDC 112
-
+#define CLK_MBUS 113
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
index 6b7af80c26ec..484c2a22919d 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -98,6 +98,9 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
--
2.24.1
^ permalink raw reply related [flat|nested] 13+ messages in thread