* [PATCH v2 0/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
Hi everyone,
This is v2 of the AXP806 PMIC support series. The patch "regulator: core:
Try full range when adjusting regulators to constraints" has been dropped.
Other changes are inline in the patches.
This series adds support for X-Powers' AXP806 PMIC. This is the secondary
PMIC accompanying Allwinner's A80 SoC. For now, only the regulators are
supported. While the AXP806 supports standalone operation, no hardware
exists, so this will not be supported.
Patch 1 adds AXP806 to the axp20x bindings.
Patch 2 adds AXP806 support to the axp20x mfd driver.
Patch 3 adds AXP806 support to the axp20x regulator driver.
Patch 4 adds the unused SW switch output of the AXP809 PMIC on the A80
Optimus board. This was accidentally left out of the AXP809 series.
Patch 5 adds the unused SW switch output of the AXP809 PMIC on the
Cubieboard 4. This was accidentally left out of the AXP809 series.
Patch 6 enables AXP809 support on the A80 Optimus board.
Patch 7 enables AXP809 support on the Cubieboard 4.
Patch 8 disables EHCI1 on the A80 Optimus board.
Regards
ChenYu
Chen-Yu Tsai (8):
mfd: axp20x: Add bindings for AXP806 PMIC
mfd: axp20x: Add support for AXP806 PMIC
regulator: axp20x: support AXP806 variant
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and
regulators
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and
regulators
ARM: dts: sun9i: a80-optimus: Disable EHCI1
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 116 +++++++++++++++++++++
arch/arm/boot/dts/sun9i-a80-optimus.dts | 123 ++++++++++++++++++++++-
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 +++++++++++++
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++--
include/linux/mfd/axp20x.h | 60 +++++++++++
7 files changed, 507 insertions(+), 11 deletions(-)
--
2.9.3
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 0/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
Hi everyone,
This is v2 of the AXP806 PMIC support series. The patch "regulator: core:
Try full range when adjusting regulators to constraints" has been dropped.
Other changes are inline in the patches.
This series adds support for X-Powers' AXP806 PMIC. This is the secondary
PMIC accompanying Allwinner's A80 SoC. For now, only the regulators are
supported. While the AXP806 supports standalone operation, no hardware
exists, so this will not be supported.
Patch 1 adds AXP806 to the axp20x bindings.
Patch 2 adds AXP806 support to the axp20x mfd driver.
Patch 3 adds AXP806 support to the axp20x regulator driver.
Patch 4 adds the unused SW switch output of the AXP809 PMIC on the A80
Optimus board. This was accidentally left out of the AXP809 series.
Patch 5 adds the unused SW switch output of the AXP809 PMIC on the
Cubieboard 4. This was accidentally left out of the AXP809 series.
Patch 6 enables AXP809 support on the A80 Optimus board.
Patch 7 enables AXP809 support on the Cubieboard 4.
Patch 8 disables EHCI1 on the A80 Optimus board.
Regards
ChenYu
Chen-Yu Tsai (8):
mfd: axp20x: Add bindings for AXP806 PMIC
mfd: axp20x: Add support for AXP806 PMIC
regulator: axp20x: support AXP806 variant
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and
regulators
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and
regulators
ARM: dts: sun9i: a80-optimus: Disable EHCI1
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 116 +++++++++++++++++++++
arch/arm/boot/dts/sun9i-a80-optimus.dts | 123 ++++++++++++++++++++++-
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 +++++++++++++
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++--
include/linux/mfd/axp20x.h | 60 +++++++++++
7 files changed, 507 insertions(+), 11 deletions(-)
--
2.9.3
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 0/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
Hi everyone,
This is v2 of the AXP806 PMIC support series. The patch "regulator: core:
Try full range when adjusting regulators to constraints" has been dropped.
Other changes are inline in the patches.
This series adds support for X-Powers' AXP806 PMIC. This is the secondary
PMIC accompanying Allwinner's A80 SoC. For now, only the regulators are
supported. While the AXP806 supports standalone operation, no hardware
exists, so this will not be supported.
Patch 1 adds AXP806 to the axp20x bindings.
Patch 2 adds AXP806 support to the axp20x mfd driver.
Patch 3 adds AXP806 support to the axp20x regulator driver.
Patch 4 adds the unused SW switch output of the AXP809 PMIC on the A80
Optimus board. This was accidentally left out of the AXP809 series.
Patch 5 adds the unused SW switch output of the AXP809 PMIC on the
Cubieboard 4. This was accidentally left out of the AXP809 series.
Patch 6 enables AXP809 support on the A80 Optimus board.
Patch 7 enables AXP809 support on the Cubieboard 4.
Patch 8 disables EHCI1 on the A80 Optimus board.
Regards
ChenYu
Chen-Yu Tsai (8):
mfd: axp20x: Add bindings for AXP806 PMIC
mfd: axp20x: Add support for AXP806 PMIC
regulator: axp20x: support AXP806 variant
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and
regulators
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and
regulators
ARM: dts: sun9i: a80-optimus: Disable EHCI1
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 116 +++++++++++++++++++++
arch/arm/boot/dts/sun9i-a80-optimus.dts | 123 ++++++++++++++++++++++-
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 +++++++++++++
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++--
include/linux/mfd/axp20x.h | 60 +++++++++++
7 files changed, 507 insertions(+), 11 deletions(-)
--
2.9.3
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 1/8] mfd: axp20x: Add bindings for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
This patch adds the basic and regulator bindings for the X-Powers AXP806
PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 ++++++++++++++++++++++--
1 file changed, 26 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 585a95546288..8f3ad9ab4637 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -10,7 +10,8 @@ axp809 (X-Powers)
Required properties:
- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
- "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
+ "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
+ "x-powers,axp809"
- reg: The I2C slave address or RSB hardware address for the AXP chip
- interrupt-parent: The parent interrupt controller
- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
@@ -47,7 +48,6 @@ Optional properties for DCDC regulators:
probably makes sense for HiFi audio related
applications that aren't battery constrained.
-
AXP202/AXP209 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
@@ -86,6 +86,30 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
RTC_LDO : LDO : ips-supply : always on
DRIVEVBUS : Enable output : drivevbus-supply : external regulator
+AXP806 regulators, type, and corresponding input supply names:
+
+Regulator Type Supply Name Notes
+--------- ---- ----------- -----
+DCDCA : DC-DC buck : vina-supply : poly-phase capable
+DCDCB : DC-DC buck : vinb-supply : poly-phase capable
+DCDCC : DC-DC buck : vinc-supply : poly-phase capable
+DCDCD : DC-DC buck : vind-supply : poly-phase capable
+DCDCE : DC-DC buck : vine-supply : poly-phase capable
+ALDO1 : LDO : aldoin-supply : shared supply
+ALDO2 : LDO : aldoin-supply : shared supply
+ALDO3 : LDO : aldoin-supply : shared supply
+BLDO1 : LDO : bldoin-supply : shared supply
+BLDO2 : LDO : bldoin-supply : shared supply
+BLDO3 : LDO : bldoin-supply : shared supply
+BLDO4 : LDO : bldoin-supply : shared supply
+CLDO1 : LDO : cldoin-supply : shared supply
+CLDO2 : LDO : cldoin-supply : shared supply
+CLDO3 : LDO : cldoin-supply : shared supply
+SW : On/Off Switch : swin-supply
+
+Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
+for higher output current. The possible groupings are: A+B, A+B+C, D+E.
+
AXP809 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 1/8] mfd: axp20x: Add bindings for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
This patch adds the basic and regulator bindings for the X-Powers AXP806
PMIC.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1: none
---
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 ++++++++++++++++++++++--
1 file changed, 26 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 585a95546288..8f3ad9ab4637 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -10,7 +10,8 @@ axp809 (X-Powers)
Required properties:
- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
- "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
+ "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
+ "x-powers,axp809"
- reg: The I2C slave address or RSB hardware address for the AXP chip
- interrupt-parent: The parent interrupt controller
- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
@@ -47,7 +48,6 @@ Optional properties for DCDC regulators:
probably makes sense for HiFi audio related
applications that aren't battery constrained.
-
AXP202/AXP209 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
@@ -86,6 +86,30 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
RTC_LDO : LDO : ips-supply : always on
DRIVEVBUS : Enable output : drivevbus-supply : external regulator
+AXP806 regulators, type, and corresponding input supply names:
+
+Regulator Type Supply Name Notes
+--------- ---- ----------- -----
+DCDCA : DC-DC buck : vina-supply : poly-phase capable
+DCDCB : DC-DC buck : vinb-supply : poly-phase capable
+DCDCC : DC-DC buck : vinc-supply : poly-phase capable
+DCDCD : DC-DC buck : vind-supply : poly-phase capable
+DCDCE : DC-DC buck : vine-supply : poly-phase capable
+ALDO1 : LDO : aldoin-supply : shared supply
+ALDO2 : LDO : aldoin-supply : shared supply
+ALDO3 : LDO : aldoin-supply : shared supply
+BLDO1 : LDO : bldoin-supply : shared supply
+BLDO2 : LDO : bldoin-supply : shared supply
+BLDO3 : LDO : bldoin-supply : shared supply
+BLDO4 : LDO : bldoin-supply : shared supply
+CLDO1 : LDO : cldoin-supply : shared supply
+CLDO2 : LDO : cldoin-supply : shared supply
+CLDO3 : LDO : cldoin-supply : shared supply
+SW : On/Off Switch : swin-supply
+
+Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
+for higher output current. The possible groupings are: A+B, A+B+C, D+E.
+
AXP809 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 1/8] mfd: axp20x: Add bindings for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds the basic and regulator bindings for the X-Powers AXP806
PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 ++++++++++++++++++++++--
1 file changed, 26 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 585a95546288..8f3ad9ab4637 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -10,7 +10,8 @@ axp809 (X-Powers)
Required properties:
- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
- "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
+ "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
+ "x-powers,axp809"
- reg: The I2C slave address or RSB hardware address for the AXP chip
- interrupt-parent: The parent interrupt controller
- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
@@ -47,7 +48,6 @@ Optional properties for DCDC regulators:
probably makes sense for HiFi audio related
applications that aren't battery constrained.
-
AXP202/AXP209 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
@@ -86,6 +86,30 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
RTC_LDO : LDO : ips-supply : always on
DRIVEVBUS : Enable output : drivevbus-supply : external regulator
+AXP806 regulators, type, and corresponding input supply names:
+
+Regulator Type Supply Name Notes
+--------- ---- ----------- -----
+DCDCA : DC-DC buck : vina-supply : poly-phase capable
+DCDCB : DC-DC buck : vinb-supply : poly-phase capable
+DCDCC : DC-DC buck : vinc-supply : poly-phase capable
+DCDCD : DC-DC buck : vind-supply : poly-phase capable
+DCDCE : DC-DC buck : vine-supply : poly-phase capable
+ALDO1 : LDO : aldoin-supply : shared supply
+ALDO2 : LDO : aldoin-supply : shared supply
+ALDO3 : LDO : aldoin-supply : shared supply
+BLDO1 : LDO : bldoin-supply : shared supply
+BLDO2 : LDO : bldoin-supply : shared supply
+BLDO3 : LDO : bldoin-supply : shared supply
+BLDO4 : LDO : bldoin-supply : shared supply
+CLDO1 : LDO : cldoin-supply : shared supply
+CLDO2 : LDO : cldoin-supply : shared supply
+CLDO3 : LDO : cldoin-supply : shared supply
+SW : On/Off Switch : swin-supply
+
+Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
+for higher output current. The possible groupings are: A+B, A+B+C, D+E.
+
AXP809 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 2/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/axp20x.h | 60 ++++++++++++++++++++++++++++++++++++++
3 files changed, 133 insertions(+)
diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
index a407527bcd09..a732cb50bcff 100644
--- a/drivers/mfd/axp20x-rsb.c
+++ b/drivers/mfd/axp20x-rsb.c
@@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
static const struct of_device_id axp20x_rsb_of_match[] = {
{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
{ .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
{ },
};
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index fd80b0981f0f..96102753847f 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
"AXP221",
"AXP223",
"AXP288",
+ "AXP806",
"AXP809",
};
@@ -129,6 +130,27 @@ static const struct regmap_access_table axp288_volatile_table = {
.n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
};
+static const struct regmap_range axp806_writeable_ranges[] = {
+ regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+ regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
+ regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
+ regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
+static const struct regmap_range axp806_volatile_ranges[] = {
+ regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
+static const struct regmap_access_table axp806_writeable_table = {
+ .yes_ranges = axp806_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp806_writeable_ranges),
+};
+
+static const struct regmap_access_table axp806_volatile_table = {
+ .yes_ranges = axp806_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp806_volatile_ranges),
+};
+
static struct resource axp152_pek_resources[] = {
DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
@@ -278,6 +300,15 @@ static const struct regmap_config axp288_regmap_config = {
.cache_type = REGCACHE_RBTREE,
};
+static const struct regmap_config axp806_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .wr_table = &axp806_writeable_table,
+ .volatile_table = &axp806_volatile_table,
+ .max_register = AXP806_VREF_TEMP_WARN_L,
+ .cache_type = REGCACHE_RBTREE,
+};
+
#define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
[_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
@@ -409,6 +440,21 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
};
+static const struct regmap_irq axp806_regmap_irqs[] = {
+ INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
+ INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
+ INIT_REGMAP_IRQ(AXP806, DCDCA_V_LOW, 0, 3),
+ INIT_REGMAP_IRQ(AXP806, DCDCB_V_LOW, 0, 4),
+ INIT_REGMAP_IRQ(AXP806, DCDCC_V_LOW, 0, 5),
+ INIT_REGMAP_IRQ(AXP806, DCDCD_V_LOW, 0, 6),
+ INIT_REGMAP_IRQ(AXP806, DCDCE_V_LOW, 0, 7),
+ INIT_REGMAP_IRQ(AXP806, PWROK_LONG, 1, 0),
+ INIT_REGMAP_IRQ(AXP806, PWROK_SHORT, 1, 1),
+ INIT_REGMAP_IRQ(AXP806, WAKEUP, 1, 4),
+ INIT_REGMAP_IRQ(AXP806, PWROK_FALL, 1, 5),
+ INIT_REGMAP_IRQ(AXP806, PWROK_RISE, 1, 6),
+};
+
static const struct regmap_irq axp809_regmap_irqs[] = {
INIT_REGMAP_IRQ(AXP809, ACIN_OVER_V, 0, 7),
INIT_REGMAP_IRQ(AXP809, ACIN_PLUGIN, 0, 6),
@@ -494,6 +540,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
};
+static const struct regmap_irq_chip axp806_regmap_irq_chip = {
+ .name = "axp806",
+ .status_base = AXP20X_IRQ1_STATE,
+ .ack_base = AXP20X_IRQ1_STATE,
+ .mask_base = AXP20X_IRQ1_EN,
+ .mask_invert = true,
+ .init_ack_masked = true,
+ .irqs = axp806_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(axp806_regmap_irqs),
+ .num_regs = 2,
+};
+
static const struct regmap_irq_chip axp809_regmap_irq_chip = {
.name = "axp809",
.status_base = AXP20X_IRQ1_STATE,
@@ -660,12 +718,20 @@ static struct mfd_cell axp288_cells[] = {
},
};
+static struct mfd_cell axp806_cells[] = {
+ {
+ .id = 2,
+ .name = "axp20x-regulator",
+ },
+};
+
static struct mfd_cell axp809_cells[] = {
{
.name = "axp20x-pek",
.num_resources = ARRAY_SIZE(axp809_pek_resources),
.resources = axp809_pek_resources,
}, {
+ .id = 1,
.name = "axp20x-regulator",
},
};
@@ -732,6 +798,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
axp20x->regmap_cfg = &axp288_regmap_config;
axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
break;
+ case AXP806_ID:
+ axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
+ axp20x->cells = axp806_cells;
+ axp20x->regmap_cfg = &axp806_regmap_config;
+ axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
+ break;
case AXP809_ID:
axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
axp20x->cells = axp809_cells;
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index 0be4982f08fe..fec597fb34cb 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -20,6 +20,7 @@ enum {
AXP221_ID,
AXP223_ID,
AXP288_ID,
+ AXP806_ID,
AXP809_ID,
NR_AXP20X_VARIANTS,
};
@@ -91,6 +92,30 @@ enum {
#define AXP22X_ALDO3_V_OUT 0x2a
#define AXP22X_CHRG_CTRL3 0x35
+#define AXP806_STARTUP_SRC 0x00
+#define AXP806_CHIP_ID 0x03
+#define AXP806_PWR_OUT_CTRL1 0x10
+#define AXP806_PWR_OUT_CTRL2 0x11
+#define AXP806_DCDCA_V_CTRL 0x12
+#define AXP806_DCDCB_V_CTRL 0x13
+#define AXP806_DCDCC_V_CTRL 0x14
+#define AXP806_DCDCD_V_CTRL 0x15
+#define AXP806_DCDCE_V_CTRL 0x16
+#define AXP806_ALDO1_V_CTRL 0x17
+#define AXP806_ALDO2_V_CTRL 0x18
+#define AXP806_ALDO3_V_CTRL 0x19
+#define AXP806_DCDC_MODE_CTRL1 0x1a
+#define AXP806_DCDC_MODE_CTRL2 0x1b
+#define AXP806_DCDC_FREQ_CTRL 0x1c
+#define AXP806_BLDO1_V_CTRL 0x20
+#define AXP806_BLDO2_V_CTRL 0x21
+#define AXP806_BLDO3_V_CTRL 0x22
+#define AXP806_BLDO4_V_CTRL 0x23
+#define AXP806_CLDO1_V_CTRL 0x24
+#define AXP806_CLDO2_V_CTRL 0x25
+#define AXP806_CLDO3_V_CTRL 0x26
+#define AXP806_VREF_TEMP_WARN_L 0xf3
+
/* Interrupt */
#define AXP152_IRQ1_EN 0x40
#define AXP152_IRQ2_EN 0x41
@@ -266,6 +291,26 @@ enum {
};
enum {
+ AXP806_DCDCA = 0,
+ AXP806_DCDCB,
+ AXP806_DCDCC,
+ AXP806_DCDCD,
+ AXP806_DCDCE,
+ AXP806_ALDO1,
+ AXP806_ALDO2,
+ AXP806_ALDO3,
+ AXP806_BLDO1,
+ AXP806_BLDO2,
+ AXP806_BLDO3,
+ AXP806_BLDO4,
+ AXP806_CLDO1,
+ AXP806_CLDO2,
+ AXP806_CLDO3,
+ AXP806_SW,
+ AXP806_REG_ID_MAX,
+};
+
+enum {
AXP809_DCDC1 = 0,
AXP809_DCDC2,
AXP809_DCDC3,
@@ -414,6 +459,21 @@ enum axp288_irqs {
AXP288_IRQ_BC_USB_CHNG,
};
+enum axp806_irqs {
+ AXP806_IRQ_DIE_TEMP_HIGH_LV1,
+ AXP806_IRQ_DIE_TEMP_HIGH_LV2,
+ AXP806_IRQ_DCDCA_V_LOW,
+ AXP806_IRQ_DCDCB_V_LOW,
+ AXP806_IRQ_DCDCC_V_LOW,
+ AXP806_IRQ_DCDCD_V_LOW,
+ AXP806_IRQ_DCDCE_V_LOW,
+ AXP806_IRQ_PWROK_LONG,
+ AXP806_IRQ_PWROK_SHORT,
+ AXP806_IRQ_WAKEUP,
+ AXP806_IRQ_PWROK_FALL,
+ AXP806_IRQ_PWROK_RISE,
+};
+
enum axp809_irqs {
AXP809_IRQ_ACIN_OVER_V = 1,
AXP809_IRQ_ACIN_PLUGIN,
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 2/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1: none
---
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/axp20x.h | 60 ++++++++++++++++++++++++++++++++++++++
3 files changed, 133 insertions(+)
diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
index a407527bcd09..a732cb50bcff 100644
--- a/drivers/mfd/axp20x-rsb.c
+++ b/drivers/mfd/axp20x-rsb.c
@@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
static const struct of_device_id axp20x_rsb_of_match[] = {
{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
{ .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
{ },
};
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index fd80b0981f0f..96102753847f 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
"AXP221",
"AXP223",
"AXP288",
+ "AXP806",
"AXP809",
};
@@ -129,6 +130,27 @@ static const struct regmap_access_table axp288_volatile_table = {
.n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
};
+static const struct regmap_range axp806_writeable_ranges[] = {
+ regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+ regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
+ regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
+ regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
+static const struct regmap_range axp806_volatile_ranges[] = {
+ regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
+static const struct regmap_access_table axp806_writeable_table = {
+ .yes_ranges = axp806_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp806_writeable_ranges),
+};
+
+static const struct regmap_access_table axp806_volatile_table = {
+ .yes_ranges = axp806_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp806_volatile_ranges),
+};
+
static struct resource axp152_pek_resources[] = {
DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
@@ -278,6 +300,15 @@ static const struct regmap_config axp288_regmap_config = {
.cache_type = REGCACHE_RBTREE,
};
+static const struct regmap_config axp806_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .wr_table = &axp806_writeable_table,
+ .volatile_table = &axp806_volatile_table,
+ .max_register = AXP806_VREF_TEMP_WARN_L,
+ .cache_type = REGCACHE_RBTREE,
+};
+
#define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
[_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
@@ -409,6 +440,21 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
};
+static const struct regmap_irq axp806_regmap_irqs[] = {
+ INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
+ INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
+ INIT_REGMAP_IRQ(AXP806, DCDCA_V_LOW, 0, 3),
+ INIT_REGMAP_IRQ(AXP806, DCDCB_V_LOW, 0, 4),
+ INIT_REGMAP_IRQ(AXP806, DCDCC_V_LOW, 0, 5),
+ INIT_REGMAP_IRQ(AXP806, DCDCD_V_LOW, 0, 6),
+ INIT_REGMAP_IRQ(AXP806, DCDCE_V_LOW, 0, 7),
+ INIT_REGMAP_IRQ(AXP806, PWROK_LONG, 1, 0),
+ INIT_REGMAP_IRQ(AXP806, PWROK_SHORT, 1, 1),
+ INIT_REGMAP_IRQ(AXP806, WAKEUP, 1, 4),
+ INIT_REGMAP_IRQ(AXP806, PWROK_FALL, 1, 5),
+ INIT_REGMAP_IRQ(AXP806, PWROK_RISE, 1, 6),
+};
+
static const struct regmap_irq axp809_regmap_irqs[] = {
INIT_REGMAP_IRQ(AXP809, ACIN_OVER_V, 0, 7),
INIT_REGMAP_IRQ(AXP809, ACIN_PLUGIN, 0, 6),
@@ -494,6 +540,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
};
+static const struct regmap_irq_chip axp806_regmap_irq_chip = {
+ .name = "axp806",
+ .status_base = AXP20X_IRQ1_STATE,
+ .ack_base = AXP20X_IRQ1_STATE,
+ .mask_base = AXP20X_IRQ1_EN,
+ .mask_invert = true,
+ .init_ack_masked = true,
+ .irqs = axp806_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(axp806_regmap_irqs),
+ .num_regs = 2,
+};
+
static const struct regmap_irq_chip axp809_regmap_irq_chip = {
.name = "axp809",
.status_base = AXP20X_IRQ1_STATE,
@@ -660,12 +718,20 @@ static struct mfd_cell axp288_cells[] = {
},
};
+static struct mfd_cell axp806_cells[] = {
+ {
+ .id = 2,
+ .name = "axp20x-regulator",
+ },
+};
+
static struct mfd_cell axp809_cells[] = {
{
.name = "axp20x-pek",
.num_resources = ARRAY_SIZE(axp809_pek_resources),
.resources = axp809_pek_resources,
}, {
+ .id = 1,
.name = "axp20x-regulator",
},
};
@@ -732,6 +798,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
axp20x->regmap_cfg = &axp288_regmap_config;
axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
break;
+ case AXP806_ID:
+ axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
+ axp20x->cells = axp806_cells;
+ axp20x->regmap_cfg = &axp806_regmap_config;
+ axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
+ break;
case AXP809_ID:
axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
axp20x->cells = axp809_cells;
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index 0be4982f08fe..fec597fb34cb 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -20,6 +20,7 @@ enum {
AXP221_ID,
AXP223_ID,
AXP288_ID,
+ AXP806_ID,
AXP809_ID,
NR_AXP20X_VARIANTS,
};
@@ -91,6 +92,30 @@ enum {
#define AXP22X_ALDO3_V_OUT 0x2a
#define AXP22X_CHRG_CTRL3 0x35
+#define AXP806_STARTUP_SRC 0x00
+#define AXP806_CHIP_ID 0x03
+#define AXP806_PWR_OUT_CTRL1 0x10
+#define AXP806_PWR_OUT_CTRL2 0x11
+#define AXP806_DCDCA_V_CTRL 0x12
+#define AXP806_DCDCB_V_CTRL 0x13
+#define AXP806_DCDCC_V_CTRL 0x14
+#define AXP806_DCDCD_V_CTRL 0x15
+#define AXP806_DCDCE_V_CTRL 0x16
+#define AXP806_ALDO1_V_CTRL 0x17
+#define AXP806_ALDO2_V_CTRL 0x18
+#define AXP806_ALDO3_V_CTRL 0x19
+#define AXP806_DCDC_MODE_CTRL1 0x1a
+#define AXP806_DCDC_MODE_CTRL2 0x1b
+#define AXP806_DCDC_FREQ_CTRL 0x1c
+#define AXP806_BLDO1_V_CTRL 0x20
+#define AXP806_BLDO2_V_CTRL 0x21
+#define AXP806_BLDO3_V_CTRL 0x22
+#define AXP806_BLDO4_V_CTRL 0x23
+#define AXP806_CLDO1_V_CTRL 0x24
+#define AXP806_CLDO2_V_CTRL 0x25
+#define AXP806_CLDO3_V_CTRL 0x26
+#define AXP806_VREF_TEMP_WARN_L 0xf3
+
/* Interrupt */
#define AXP152_IRQ1_EN 0x40
#define AXP152_IRQ2_EN 0x41
@@ -266,6 +291,26 @@ enum {
};
enum {
+ AXP806_DCDCA = 0,
+ AXP806_DCDCB,
+ AXP806_DCDCC,
+ AXP806_DCDCD,
+ AXP806_DCDCE,
+ AXP806_ALDO1,
+ AXP806_ALDO2,
+ AXP806_ALDO3,
+ AXP806_BLDO1,
+ AXP806_BLDO2,
+ AXP806_BLDO3,
+ AXP806_BLDO4,
+ AXP806_CLDO1,
+ AXP806_CLDO2,
+ AXP806_CLDO3,
+ AXP806_SW,
+ AXP806_REG_ID_MAX,
+};
+
+enum {
AXP809_DCDC1 = 0,
AXP809_DCDC2,
AXP809_DCDC3,
@@ -414,6 +459,21 @@ enum axp288_irqs {
AXP288_IRQ_BC_USB_CHNG,
};
+enum axp806_irqs {
+ AXP806_IRQ_DIE_TEMP_HIGH_LV1,
+ AXP806_IRQ_DIE_TEMP_HIGH_LV2,
+ AXP806_IRQ_DCDCA_V_LOW,
+ AXP806_IRQ_DCDCB_V_LOW,
+ AXP806_IRQ_DCDCC_V_LOW,
+ AXP806_IRQ_DCDCD_V_LOW,
+ AXP806_IRQ_DCDCE_V_LOW,
+ AXP806_IRQ_PWROK_LONG,
+ AXP806_IRQ_PWROK_SHORT,
+ AXP806_IRQ_WAKEUP,
+ AXP806_IRQ_PWROK_FALL,
+ AXP806_IRQ_PWROK_RISE,
+};
+
enum axp809_irqs {
AXP809_IRQ_ACIN_OVER_V = 1,
AXP809_IRQ_ACIN_PLUGIN,
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 2/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/axp20x.h | 60 ++++++++++++++++++++++++++++++++++++++
3 files changed, 133 insertions(+)
diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
index a407527bcd09..a732cb50bcff 100644
--- a/drivers/mfd/axp20x-rsb.c
+++ b/drivers/mfd/axp20x-rsb.c
@@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
static const struct of_device_id axp20x_rsb_of_match[] = {
{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
{ .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
{ },
};
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index fd80b0981f0f..96102753847f 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
"AXP221",
"AXP223",
"AXP288",
+ "AXP806",
"AXP809",
};
@@ -129,6 +130,27 @@ static const struct regmap_access_table axp288_volatile_table = {
.n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
};
+static const struct regmap_range axp806_writeable_ranges[] = {
+ regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+ regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
+ regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
+ regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
+static const struct regmap_range axp806_volatile_ranges[] = {
+ regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
+static const struct regmap_access_table axp806_writeable_table = {
+ .yes_ranges = axp806_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp806_writeable_ranges),
+};
+
+static const struct regmap_access_table axp806_volatile_table = {
+ .yes_ranges = axp806_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp806_volatile_ranges),
+};
+
static struct resource axp152_pek_resources[] = {
DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
@@ -278,6 +300,15 @@ static const struct regmap_config axp288_regmap_config = {
.cache_type = REGCACHE_RBTREE,
};
+static const struct regmap_config axp806_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .wr_table = &axp806_writeable_table,
+ .volatile_table = &axp806_volatile_table,
+ .max_register = AXP806_VREF_TEMP_WARN_L,
+ .cache_type = REGCACHE_RBTREE,
+};
+
#define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
[_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
@@ -409,6 +440,21 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
};
+static const struct regmap_irq axp806_regmap_irqs[] = {
+ INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
+ INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
+ INIT_REGMAP_IRQ(AXP806, DCDCA_V_LOW, 0, 3),
+ INIT_REGMAP_IRQ(AXP806, DCDCB_V_LOW, 0, 4),
+ INIT_REGMAP_IRQ(AXP806, DCDCC_V_LOW, 0, 5),
+ INIT_REGMAP_IRQ(AXP806, DCDCD_V_LOW, 0, 6),
+ INIT_REGMAP_IRQ(AXP806, DCDCE_V_LOW, 0, 7),
+ INIT_REGMAP_IRQ(AXP806, PWROK_LONG, 1, 0),
+ INIT_REGMAP_IRQ(AXP806, PWROK_SHORT, 1, 1),
+ INIT_REGMAP_IRQ(AXP806, WAKEUP, 1, 4),
+ INIT_REGMAP_IRQ(AXP806, PWROK_FALL, 1, 5),
+ INIT_REGMAP_IRQ(AXP806, PWROK_RISE, 1, 6),
+};
+
static const struct regmap_irq axp809_regmap_irqs[] = {
INIT_REGMAP_IRQ(AXP809, ACIN_OVER_V, 0, 7),
INIT_REGMAP_IRQ(AXP809, ACIN_PLUGIN, 0, 6),
@@ -494,6 +540,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
};
+static const struct regmap_irq_chip axp806_regmap_irq_chip = {
+ .name = "axp806",
+ .status_base = AXP20X_IRQ1_STATE,
+ .ack_base = AXP20X_IRQ1_STATE,
+ .mask_base = AXP20X_IRQ1_EN,
+ .mask_invert = true,
+ .init_ack_masked = true,
+ .irqs = axp806_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(axp806_regmap_irqs),
+ .num_regs = 2,
+};
+
static const struct regmap_irq_chip axp809_regmap_irq_chip = {
.name = "axp809",
.status_base = AXP20X_IRQ1_STATE,
@@ -660,12 +718,20 @@ static struct mfd_cell axp288_cells[] = {
},
};
+static struct mfd_cell axp806_cells[] = {
+ {
+ .id = 2,
+ .name = "axp20x-regulator",
+ },
+};
+
static struct mfd_cell axp809_cells[] = {
{
.name = "axp20x-pek",
.num_resources = ARRAY_SIZE(axp809_pek_resources),
.resources = axp809_pek_resources,
}, {
+ .id = 1,
.name = "axp20x-regulator",
},
};
@@ -732,6 +798,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
axp20x->regmap_cfg = &axp288_regmap_config;
axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
break;
+ case AXP806_ID:
+ axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
+ axp20x->cells = axp806_cells;
+ axp20x->regmap_cfg = &axp806_regmap_config;
+ axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
+ break;
case AXP809_ID:
axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
axp20x->cells = axp809_cells;
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index 0be4982f08fe..fec597fb34cb 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -20,6 +20,7 @@ enum {
AXP221_ID,
AXP223_ID,
AXP288_ID,
+ AXP806_ID,
AXP809_ID,
NR_AXP20X_VARIANTS,
};
@@ -91,6 +92,30 @@ enum {
#define AXP22X_ALDO3_V_OUT 0x2a
#define AXP22X_CHRG_CTRL3 0x35
+#define AXP806_STARTUP_SRC 0x00
+#define AXP806_CHIP_ID 0x03
+#define AXP806_PWR_OUT_CTRL1 0x10
+#define AXP806_PWR_OUT_CTRL2 0x11
+#define AXP806_DCDCA_V_CTRL 0x12
+#define AXP806_DCDCB_V_CTRL 0x13
+#define AXP806_DCDCC_V_CTRL 0x14
+#define AXP806_DCDCD_V_CTRL 0x15
+#define AXP806_DCDCE_V_CTRL 0x16
+#define AXP806_ALDO1_V_CTRL 0x17
+#define AXP806_ALDO2_V_CTRL 0x18
+#define AXP806_ALDO3_V_CTRL 0x19
+#define AXP806_DCDC_MODE_CTRL1 0x1a
+#define AXP806_DCDC_MODE_CTRL2 0x1b
+#define AXP806_DCDC_FREQ_CTRL 0x1c
+#define AXP806_BLDO1_V_CTRL 0x20
+#define AXP806_BLDO2_V_CTRL 0x21
+#define AXP806_BLDO3_V_CTRL 0x22
+#define AXP806_BLDO4_V_CTRL 0x23
+#define AXP806_CLDO1_V_CTRL 0x24
+#define AXP806_CLDO2_V_CTRL 0x25
+#define AXP806_CLDO3_V_CTRL 0x26
+#define AXP806_VREF_TEMP_WARN_L 0xf3
+
/* Interrupt */
#define AXP152_IRQ1_EN 0x40
#define AXP152_IRQ2_EN 0x41
@@ -266,6 +291,26 @@ enum {
};
enum {
+ AXP806_DCDCA = 0,
+ AXP806_DCDCB,
+ AXP806_DCDCC,
+ AXP806_DCDCD,
+ AXP806_DCDCE,
+ AXP806_ALDO1,
+ AXP806_ALDO2,
+ AXP806_ALDO3,
+ AXP806_BLDO1,
+ AXP806_BLDO2,
+ AXP806_BLDO3,
+ AXP806_BLDO4,
+ AXP806_CLDO1,
+ AXP806_CLDO2,
+ AXP806_CLDO3,
+ AXP806_SW,
+ AXP806_REG_ID_MAX,
+};
+
+enum {
AXP809_DCDC1 = 0,
AXP809_DCDC2,
AXP809_DCDC3,
@@ -414,6 +459,21 @@ enum axp288_irqs {
AXP288_IRQ_BC_USB_CHNG,
};
+enum axp806_irqs {
+ AXP806_IRQ_DIE_TEMP_HIGH_LV1,
+ AXP806_IRQ_DIE_TEMP_HIGH_LV2,
+ AXP806_IRQ_DCDCA_V_LOW,
+ AXP806_IRQ_DCDCB_V_LOW,
+ AXP806_IRQ_DCDCC_V_LOW,
+ AXP806_IRQ_DCDCD_V_LOW,
+ AXP806_IRQ_DCDCE_V_LOW,
+ AXP806_IRQ_PWROK_LONG,
+ AXP806_IRQ_PWROK_SHORT,
+ AXP806_IRQ_WAKEUP,
+ AXP806_IRQ_PWROK_FALL,
+ AXP806_IRQ_PWROK_RISE,
+};
+
enum axp809_irqs {
AXP809_IRQ_ACIN_OVER_V = 1,
AXP809_IRQ_ACIN_PLUGIN,
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.
Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.
Add support for this new variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Use switch-case block in axp20x_is_polyphase_slave
---
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++++++++++++++---
1 file changed, 111 insertions(+), 7 deletions(-)
diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index 6d9ac76a772f..54382ef902c6 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -244,16 +244,64 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
.ops = &axp20x_ops_sw,
};
-static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
- REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
- REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+static const struct regulator_linear_range axp806_dcdca_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x32, 10000),
+ REGULATOR_LINEAR_RANGE(1120000, 0x33, 0x47, 20000),
};
-static const struct regulator_linear_range axp809_dldo1_ranges[] = {
+static const struct regulator_linear_range axp806_dcdcd_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2d, 20000),
+ REGULATOR_LINEAR_RANGE(1600000, 0x2e, 0x3f, 100000),
+};
+
+static const struct regulator_linear_range axp806_cldo2_ranges[] = {
REGULATOR_LINEAR_RANGE(700000, 0x0, 0x1a, 100000),
REGULATOR_LINEAR_RANGE(3400000, 0x1b, 0x1f, 200000),
};
+static const struct regulator_desc axp806_regulators[] = {
+ AXP_DESC_RANGES(AXP806, DCDCA, "dcdca", "vina", axp806_dcdca_ranges,
+ 72, AXP806_DCDCA_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
+ BIT(0)),
+ AXP_DESC(AXP806, DCDCB, "dcdcb", "vinb", 1000, 2550, 50,
+ AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(1)),
+ AXP_DESC_RANGES(AXP806, DCDCC, "dcdcc", "vinc", axp806_dcdca_ranges,
+ 72, AXP806_DCDCC_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
+ BIT(2)),
+ AXP_DESC_RANGES(AXP806, DCDCD, "dcdcd", "vind", axp806_dcdcd_ranges,
+ 64, AXP806_DCDCD_V_CTRL, 0x3f, AXP806_PWR_OUT_CTRL1,
+ BIT(3)),
+ AXP_DESC(AXP806, DCDCE, "dcdce", "vine", 1100, 3400, 100,
+ AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(4)),
+ AXP_DESC(AXP806, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
+ AXP806_ALDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(5)),
+ AXP_DESC(AXP806, ALDO2, "aldo2", "aldoin", 700, 3400, 100,
+ AXP806_ALDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(6)),
+ AXP_DESC(AXP806, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
+ AXP806_ALDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(7)),
+ AXP_DESC(AXP806, BLDO1, "bldo1", "bldoin", 700, 1900, 100,
+ AXP806_BLDO1_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(0)),
+ AXP_DESC(AXP806, BLDO2, "bldo2", "bldoin", 700, 1900, 100,
+ AXP806_BLDO2_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(1)),
+ AXP_DESC(AXP806, BLDO3, "bldo3", "bldoin", 700, 1900, 100,
+ AXP806_BLDO3_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(2)),
+ AXP_DESC(AXP806, BLDO4, "bldo4", "bldoin", 700, 1900, 100,
+ AXP806_BLDO4_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(3)),
+ AXP_DESC(AXP806, CLDO1, "cldo1", "cldoin", 700, 3300, 100,
+ AXP806_CLDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(4)),
+ AXP_DESC_RANGES(AXP806, CLDO2, "cldo2", "cldoin", axp806_cldo2_ranges,
+ 32, AXP806_CLDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2,
+ BIT(5)),
+ AXP_DESC(AXP806, CLDO3, "cldo3", "cldoin", 700, 3300, 100,
+ AXP806_CLDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(6)),
+ AXP_DESC_SW(AXP806, SW, "sw", "swin", AXP806_PWR_OUT_CTRL2, BIT(7)),
+};
+
+static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+};
+
static const struct regulator_desc axp809_regulators[] = {
AXP_DESC(AXP809, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
AXP22X_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(1)),
@@ -278,7 +326,7 @@ static const struct regulator_desc axp809_regulators[] = {
AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(7)),
AXP_DESC(AXP809, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
- AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp809_dldo1_ranges,
+ AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp806_cldo2_ranges,
32, AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
BIT(3)),
AXP_DESC(AXP809, DLDO2, "dldo2", "dldoin", 700, 3300, 100,
@@ -302,6 +350,7 @@ static const struct regulator_desc axp809_regulators[] = {
static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
{
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+ unsigned int reg = AXP20X_DCDC_FREQ;
u32 min, max, def, step;
switch (axp20x->variant) {
@@ -312,6 +361,14 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
def = 1500;
step = 75;
break;
+ case AXP806_ID:
+ /*
+ * AXP806 DCDC work frequency setting has the same range and
+ * step as AXP22X, but at a different register.
+ * Fall through to the check below.
+ * (See include/linux/mfd/axp20x.h)
+ */
+ reg = AXP806_DCDC_FREQ_CTRL;
case AXP221_ID:
case AXP223_ID:
case AXP809_ID:
@@ -343,7 +400,7 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
dcdcfreq = (dcdcfreq - min) / step;
- return regmap_update_bits(axp20x->regmap, AXP20X_DCDC_FREQ,
+ return regmap_update_bits(axp20x->regmap, reg,
AXP20X_FREQ_DCDC_MASK, dcdcfreq);
}
@@ -377,6 +434,7 @@ static int axp20x_regulator_parse_dt(struct platform_device *pdev)
static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 workmode)
{
struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
+ unsigned int reg = AXP20X_DCDC_MODE;
unsigned int mask;
switch (axp20x->variant) {
@@ -392,6 +450,13 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
workmode <<= ffs(mask) - 1;
break;
+ case AXP806_ID:
+ reg = AXP806_DCDC_MODE_CTRL2;
+ /*
+ * AXP806 DCDC regulator IDs have the same range as AXP22X.
+ * Fall through to the check below.
+ * (See include/linux/mfd/axp20x.h)
+ */
case AXP221_ID:
case AXP223_ID:
case AXP809_ID:
@@ -408,7 +473,34 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
return -EINVAL;
}
- return regmap_update_bits(rdev->regmap, AXP20X_DCDC_MODE, mask, workmode);
+ return regmap_update_bits(rdev->regmap, reg, mask, workmode);
+}
+
+/*
+ * This function checks whether a regulator is part of a poly-phase
+ * output setup based on the registers settings. Returns true if it is.
+ */
+static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
+{
+ u32 reg = 0;
+
+ /* Only AXP806 has poly-phase outputs */
+ if (axp20x->variant != AXP806_ID)
+ return false;
+
+ regmap_read(axp20x->regmap, AXP806_DCDC_MODE_CTRL2, ®);
+
+ switch (id) {
+ case AXP806_DCDCB:
+ return (((reg & GENMASK(7, 6)) == BIT(6)) ||
+ ((reg & GENMASK(7, 6)) == BIT(7)));
+ case AXP806_DCDCC:
+ return ((reg & GENMASK(7, 6)) == BIT(7));
+ case AXP806_DCDCE:
+ return !!(reg & BIT(5));
+ }
+
+ return false;
}
static int axp20x_regulator_probe(struct platform_device *pdev)
@@ -440,6 +532,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
"x-powers,drive-vbus-en");
break;
+ case AXP806_ID:
+ regulators = axp806_regulators;
+ nregulators = AXP806_REG_ID_MAX;
+ break;
case AXP809_ID:
regulators = axp809_regulators;
nregulators = AXP809_REG_ID_MAX;
@@ -458,6 +554,14 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
struct regulator_desc *new_desc;
/*
+ * If this regulator is a slave in a poly-phase setup,
+ * skip it, as its controls are bound to the master
+ * regulator and won't work.
+ */
+ if (axp20x_is_polyphase_slave(axp20x, i))
+ continue;
+
+ /*
* Regulators DC1SW and DC5LDO are connected internally,
* so we have to handle their supply names separately.
*
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.
Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.
Add support for this new variant.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1:
- Use switch-case block in axp20x_is_polyphase_slave
---
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++++++++++++++---
1 file changed, 111 insertions(+), 7 deletions(-)
diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index 6d9ac76a772f..54382ef902c6 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -244,16 +244,64 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
.ops = &axp20x_ops_sw,
};
-static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
- REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
- REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+static const struct regulator_linear_range axp806_dcdca_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x32, 10000),
+ REGULATOR_LINEAR_RANGE(1120000, 0x33, 0x47, 20000),
};
-static const struct regulator_linear_range axp809_dldo1_ranges[] = {
+static const struct regulator_linear_range axp806_dcdcd_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2d, 20000),
+ REGULATOR_LINEAR_RANGE(1600000, 0x2e, 0x3f, 100000),
+};
+
+static const struct regulator_linear_range axp806_cldo2_ranges[] = {
REGULATOR_LINEAR_RANGE(700000, 0x0, 0x1a, 100000),
REGULATOR_LINEAR_RANGE(3400000, 0x1b, 0x1f, 200000),
};
+static const struct regulator_desc axp806_regulators[] = {
+ AXP_DESC_RANGES(AXP806, DCDCA, "dcdca", "vina", axp806_dcdca_ranges,
+ 72, AXP806_DCDCA_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
+ BIT(0)),
+ AXP_DESC(AXP806, DCDCB, "dcdcb", "vinb", 1000, 2550, 50,
+ AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(1)),
+ AXP_DESC_RANGES(AXP806, DCDCC, "dcdcc", "vinc", axp806_dcdca_ranges,
+ 72, AXP806_DCDCC_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
+ BIT(2)),
+ AXP_DESC_RANGES(AXP806, DCDCD, "dcdcd", "vind", axp806_dcdcd_ranges,
+ 64, AXP806_DCDCD_V_CTRL, 0x3f, AXP806_PWR_OUT_CTRL1,
+ BIT(3)),
+ AXP_DESC(AXP806, DCDCE, "dcdce", "vine", 1100, 3400, 100,
+ AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(4)),
+ AXP_DESC(AXP806, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
+ AXP806_ALDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(5)),
+ AXP_DESC(AXP806, ALDO2, "aldo2", "aldoin", 700, 3400, 100,
+ AXP806_ALDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(6)),
+ AXP_DESC(AXP806, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
+ AXP806_ALDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(7)),
+ AXP_DESC(AXP806, BLDO1, "bldo1", "bldoin", 700, 1900, 100,
+ AXP806_BLDO1_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(0)),
+ AXP_DESC(AXP806, BLDO2, "bldo2", "bldoin", 700, 1900, 100,
+ AXP806_BLDO2_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(1)),
+ AXP_DESC(AXP806, BLDO3, "bldo3", "bldoin", 700, 1900, 100,
+ AXP806_BLDO3_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(2)),
+ AXP_DESC(AXP806, BLDO4, "bldo4", "bldoin", 700, 1900, 100,
+ AXP806_BLDO4_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(3)),
+ AXP_DESC(AXP806, CLDO1, "cldo1", "cldoin", 700, 3300, 100,
+ AXP806_CLDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(4)),
+ AXP_DESC_RANGES(AXP806, CLDO2, "cldo2", "cldoin", axp806_cldo2_ranges,
+ 32, AXP806_CLDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2,
+ BIT(5)),
+ AXP_DESC(AXP806, CLDO3, "cldo3", "cldoin", 700, 3300, 100,
+ AXP806_CLDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(6)),
+ AXP_DESC_SW(AXP806, SW, "sw", "swin", AXP806_PWR_OUT_CTRL2, BIT(7)),
+};
+
+static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+};
+
static const struct regulator_desc axp809_regulators[] = {
AXP_DESC(AXP809, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
AXP22X_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(1)),
@@ -278,7 +326,7 @@ static const struct regulator_desc axp809_regulators[] = {
AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(7)),
AXP_DESC(AXP809, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
- AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp809_dldo1_ranges,
+ AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp806_cldo2_ranges,
32, AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
BIT(3)),
AXP_DESC(AXP809, DLDO2, "dldo2", "dldoin", 700, 3300, 100,
@@ -302,6 +350,7 @@ static const struct regulator_desc axp809_regulators[] = {
static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
{
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+ unsigned int reg = AXP20X_DCDC_FREQ;
u32 min, max, def, step;
switch (axp20x->variant) {
@@ -312,6 +361,14 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
def = 1500;
step = 75;
break;
+ case AXP806_ID:
+ /*
+ * AXP806 DCDC work frequency setting has the same range and
+ * step as AXP22X, but at a different register.
+ * Fall through to the check below.
+ * (See include/linux/mfd/axp20x.h)
+ */
+ reg = AXP806_DCDC_FREQ_CTRL;
case AXP221_ID:
case AXP223_ID:
case AXP809_ID:
@@ -343,7 +400,7 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
dcdcfreq = (dcdcfreq - min) / step;
- return regmap_update_bits(axp20x->regmap, AXP20X_DCDC_FREQ,
+ return regmap_update_bits(axp20x->regmap, reg,
AXP20X_FREQ_DCDC_MASK, dcdcfreq);
}
@@ -377,6 +434,7 @@ static int axp20x_regulator_parse_dt(struct platform_device *pdev)
static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 workmode)
{
struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
+ unsigned int reg = AXP20X_DCDC_MODE;
unsigned int mask;
switch (axp20x->variant) {
@@ -392,6 +450,13 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
workmode <<= ffs(mask) - 1;
break;
+ case AXP806_ID:
+ reg = AXP806_DCDC_MODE_CTRL2;
+ /*
+ * AXP806 DCDC regulator IDs have the same range as AXP22X.
+ * Fall through to the check below.
+ * (See include/linux/mfd/axp20x.h)
+ */
case AXP221_ID:
case AXP223_ID:
case AXP809_ID:
@@ -408,7 +473,34 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
return -EINVAL;
}
- return regmap_update_bits(rdev->regmap, AXP20X_DCDC_MODE, mask, workmode);
+ return regmap_update_bits(rdev->regmap, reg, mask, workmode);
+}
+
+/*
+ * This function checks whether a regulator is part of a poly-phase
+ * output setup based on the registers settings. Returns true if it is.
+ */
+static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
+{
+ u32 reg = 0;
+
+ /* Only AXP806 has poly-phase outputs */
+ if (axp20x->variant != AXP806_ID)
+ return false;
+
+ regmap_read(axp20x->regmap, AXP806_DCDC_MODE_CTRL2, ®);
+
+ switch (id) {
+ case AXP806_DCDCB:
+ return (((reg & GENMASK(7, 6)) == BIT(6)) ||
+ ((reg & GENMASK(7, 6)) == BIT(7)));
+ case AXP806_DCDCC:
+ return ((reg & GENMASK(7, 6)) == BIT(7));
+ case AXP806_DCDCE:
+ return !!(reg & BIT(5));
+ }
+
+ return false;
}
static int axp20x_regulator_probe(struct platform_device *pdev)
@@ -440,6 +532,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
"x-powers,drive-vbus-en");
break;
+ case AXP806_ID:
+ regulators = axp806_regulators;
+ nregulators = AXP806_REG_ID_MAX;
+ break;
case AXP809_ID:
regulators = axp809_regulators;
nregulators = AXP809_REG_ID_MAX;
@@ -458,6 +554,14 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
struct regulator_desc *new_desc;
/*
+ * If this regulator is a slave in a poly-phase setup,
+ * skip it, as its controls are bound to the master
+ * regulator and won't work.
+ */
+ if (axp20x_is_polyphase_slave(axp20x, i))
+ continue;
+
+ /*
* Regulators DC1SW and DC5LDO are connected internally,
* so we have to handle their supply names separately.
*
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.
Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.
Add support for this new variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Use switch-case block in axp20x_is_polyphase_slave
---
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++++++++++++++---
1 file changed, 111 insertions(+), 7 deletions(-)
diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index 6d9ac76a772f..54382ef902c6 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -244,16 +244,64 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
.ops = &axp20x_ops_sw,
};
-static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
- REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
- REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+static const struct regulator_linear_range axp806_dcdca_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x32, 10000),
+ REGULATOR_LINEAR_RANGE(1120000, 0x33, 0x47, 20000),
};
-static const struct regulator_linear_range axp809_dldo1_ranges[] = {
+static const struct regulator_linear_range axp806_dcdcd_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2d, 20000),
+ REGULATOR_LINEAR_RANGE(1600000, 0x2e, 0x3f, 100000),
+};
+
+static const struct regulator_linear_range axp806_cldo2_ranges[] = {
REGULATOR_LINEAR_RANGE(700000, 0x0, 0x1a, 100000),
REGULATOR_LINEAR_RANGE(3400000, 0x1b, 0x1f, 200000),
};
+static const struct regulator_desc axp806_regulators[] = {
+ AXP_DESC_RANGES(AXP806, DCDCA, "dcdca", "vina", axp806_dcdca_ranges,
+ 72, AXP806_DCDCA_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
+ BIT(0)),
+ AXP_DESC(AXP806, DCDCB, "dcdcb", "vinb", 1000, 2550, 50,
+ AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(1)),
+ AXP_DESC_RANGES(AXP806, DCDCC, "dcdcc", "vinc", axp806_dcdca_ranges,
+ 72, AXP806_DCDCC_V_CTRL, 0x7f, AXP806_PWR_OUT_CTRL1,
+ BIT(2)),
+ AXP_DESC_RANGES(AXP806, DCDCD, "dcdcd", "vind", axp806_dcdcd_ranges,
+ 64, AXP806_DCDCD_V_CTRL, 0x3f, AXP806_PWR_OUT_CTRL1,
+ BIT(3)),
+ AXP_DESC(AXP806, DCDCE, "dcdce", "vine", 1100, 3400, 100,
+ AXP806_DCDCB_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(4)),
+ AXP_DESC(AXP806, ALDO1, "aldo1", "aldoin", 700, 3300, 100,
+ AXP806_ALDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(5)),
+ AXP_DESC(AXP806, ALDO2, "aldo2", "aldoin", 700, 3400, 100,
+ AXP806_ALDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(6)),
+ AXP_DESC(AXP806, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
+ AXP806_ALDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL1, BIT(7)),
+ AXP_DESC(AXP806, BLDO1, "bldo1", "bldoin", 700, 1900, 100,
+ AXP806_BLDO1_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(0)),
+ AXP_DESC(AXP806, BLDO2, "bldo2", "bldoin", 700, 1900, 100,
+ AXP806_BLDO2_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(1)),
+ AXP_DESC(AXP806, BLDO3, "bldo3", "bldoin", 700, 1900, 100,
+ AXP806_BLDO3_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(2)),
+ AXP_DESC(AXP806, BLDO4, "bldo4", "bldoin", 700, 1900, 100,
+ AXP806_BLDO4_V_CTRL, 0x0f, AXP806_PWR_OUT_CTRL2, BIT(3)),
+ AXP_DESC(AXP806, CLDO1, "cldo1", "cldoin", 700, 3300, 100,
+ AXP806_CLDO1_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(4)),
+ AXP_DESC_RANGES(AXP806, CLDO2, "cldo2", "cldoin", axp806_cldo2_ranges,
+ 32, AXP806_CLDO2_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2,
+ BIT(5)),
+ AXP_DESC(AXP806, CLDO3, "cldo3", "cldoin", 700, 3300, 100,
+ AXP806_CLDO3_V_CTRL, 0x1f, AXP806_PWR_OUT_CTRL2, BIT(6)),
+ AXP_DESC_SW(AXP806, SW, "sw", "swin", AXP806_PWR_OUT_CTRL2, BIT(7)),
+};
+
+static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
+};
+
static const struct regulator_desc axp809_regulators[] = {
AXP_DESC(AXP809, DCDC1, "dcdc1", "vin1", 1600, 3400, 100,
AXP22X_DCDC1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(1)),
@@ -278,7 +326,7 @@ static const struct regulator_desc axp809_regulators[] = {
AXP22X_ALDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL1, BIT(7)),
AXP_DESC(AXP809, ALDO3, "aldo3", "aldoin", 700, 3300, 100,
AXP22X_ALDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(5)),
- AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp809_dldo1_ranges,
+ AXP_DESC_RANGES(AXP809, DLDO1, "dldo1", "dldoin", axp806_cldo2_ranges,
32, AXP22X_DLDO1_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2,
BIT(3)),
AXP_DESC(AXP809, DLDO2, "dldo2", "dldoin", 700, 3300, 100,
@@ -302,6 +350,7 @@ static const struct regulator_desc axp809_regulators[] = {
static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
{
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+ unsigned int reg = AXP20X_DCDC_FREQ;
u32 min, max, def, step;
switch (axp20x->variant) {
@@ -312,6 +361,14 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
def = 1500;
step = 75;
break;
+ case AXP806_ID:
+ /*
+ * AXP806 DCDC work frequency setting has the same range and
+ * step as AXP22X, but at a different register.
+ * Fall through to the check below.
+ * (See include/linux/mfd/axp20x.h)
+ */
+ reg = AXP806_DCDC_FREQ_CTRL;
case AXP221_ID:
case AXP223_ID:
case AXP809_ID:
@@ -343,7 +400,7 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
dcdcfreq = (dcdcfreq - min) / step;
- return regmap_update_bits(axp20x->regmap, AXP20X_DCDC_FREQ,
+ return regmap_update_bits(axp20x->regmap, reg,
AXP20X_FREQ_DCDC_MASK, dcdcfreq);
}
@@ -377,6 +434,7 @@ static int axp20x_regulator_parse_dt(struct platform_device *pdev)
static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 workmode)
{
struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
+ unsigned int reg = AXP20X_DCDC_MODE;
unsigned int mask;
switch (axp20x->variant) {
@@ -392,6 +450,13 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
workmode <<= ffs(mask) - 1;
break;
+ case AXP806_ID:
+ reg = AXP806_DCDC_MODE_CTRL2;
+ /*
+ * AXP806 DCDC regulator IDs have the same range as AXP22X.
+ * Fall through to the check below.
+ * (See include/linux/mfd/axp20x.h)
+ */
case AXP221_ID:
case AXP223_ID:
case AXP809_ID:
@@ -408,7 +473,34 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
return -EINVAL;
}
- return regmap_update_bits(rdev->regmap, AXP20X_DCDC_MODE, mask, workmode);
+ return regmap_update_bits(rdev->regmap, reg, mask, workmode);
+}
+
+/*
+ * This function checks whether a regulator is part of a poly-phase
+ * output setup based on the registers settings. Returns true if it is.
+ */
+static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
+{
+ u32 reg = 0;
+
+ /* Only AXP806 has poly-phase outputs */
+ if (axp20x->variant != AXP806_ID)
+ return false;
+
+ regmap_read(axp20x->regmap, AXP806_DCDC_MODE_CTRL2, ®);
+
+ switch (id) {
+ case AXP806_DCDCB:
+ return (((reg & GENMASK(7, 6)) == BIT(6)) ||
+ ((reg & GENMASK(7, 6)) == BIT(7)));
+ case AXP806_DCDCC:
+ return ((reg & GENMASK(7, 6)) == BIT(7));
+ case AXP806_DCDCE:
+ return !!(reg & BIT(5));
+ }
+
+ return false;
}
static int axp20x_regulator_probe(struct platform_device *pdev)
@@ -440,6 +532,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
"x-powers,drive-vbus-en");
break;
+ case AXP806_ID:
+ regulators = axp806_regulators;
+ nregulators = AXP806_REG_ID_MAX;
+ break;
case AXP809_ID:
regulators = axp809_regulators;
nregulators = AXP809_REG_ID_MAX;
@@ -458,6 +554,14 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
struct regulator_desc *new_desc;
/*
+ * If this regulator is a slave in a poly-phase setup,
+ * skip it, as its controls are bound to the master
+ * regulator and won't work.
+ */
+ if (axp20x_is_polyphase_slave(axp20x, i))
+ continue;
+
+ /*
* Regulators DC1SW and DC5LDO are connected internally,
* so we have to handle their supply names separately.
*
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 4/8] ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
The AXP809's SW (switch) regulator is unused on the A80 Optimus.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index fd874ded890e..caf0091e71ba 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -325,6 +325,10 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
};
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 4/8] ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The AXP809's SW (switch) regulator is unused on the A80 Optimus.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index fd874ded890e..caf0091e71ba 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -325,6 +325,10 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
};
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 4/8] ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
The AXP809's SW (switch) regulator is unused on the A80 Optimus.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index fd874ded890e..caf0091e71ba 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -325,6 +325,10 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
};
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 5/8] ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 04b014603659..910b29f0f0b5 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -253,6 +253,10 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
};
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 5/8] ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 04b014603659..910b29f0f0b5 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -253,6 +253,10 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
};
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 5/8] ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 04b014603659..910b29f0f0b5 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -253,6 +253,10 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
};
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Fixed up bldo* voltage constraints to match regulator voltage step.
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 113 ++++++++++++++++++++++++++++++++
1 file changed, 113 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index caf0091e71ba..d805cb50b5c8 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -332,6 +332,118 @@
};
};
+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <®_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec@e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
@@ -371,6 +483,7 @@
};
&usbphy2 {
+ phy-supply = <®_bldo4>;
status = "okay";
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1:
- Fixed up bldo* voltage constraints to match regulator voltage step.
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 113 ++++++++++++++++++++++++++++++++
1 file changed, 113 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index caf0091e71ba..d805cb50b5c8 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -332,6 +332,118 @@
};
};
+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <®_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec@e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
@@ -371,6 +483,7 @@
};
&usbphy2 {
+ phy-supply = <®_bldo4>;
status = "okay";
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Fixed up bldo* voltage constraints to match regulator voltage step.
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 113 ++++++++++++++++++++++++++++++++
1 file changed, 113 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index caf0091e71ba..d805cb50b5c8 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -332,6 +332,118 @@
};
};
+ axp806: pmic at 745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <®_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec at e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
@@ -371,6 +483,7 @@
};
&usbphy2 {
+ phy-supply = <®_bldo4>;
status = "okay";
};
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 7/8] ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Fixed up bldo* voltage constraints to match regulator voltage step.
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 112 ++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 910b29f0f0b5..439847acd41e 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -260,6 +260,118 @@
};
};
+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <®_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec@e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 7/8] ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1:
- Fixed up bldo* voltage constraints to match regulator voltage step.
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 112 ++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 910b29f0f0b5..439847acd41e 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -260,6 +260,118 @@
};
};
+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <®_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec@e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 7/8] ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Fixed up bldo* voltage constraints to match regulator voltage step.
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 112 ++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 910b29f0f0b5..439847acd41e 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -260,6 +260,118 @@
};
};
+ axp806: pmic at 745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <®_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec at e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 8/8] ARM: dts: sun9i: a80-optimus: Disable EHCI1
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
EHCI1 provides an HSIC interface. This interface is exposed on the
board through two pins among the GPIO header.
With the PHY now powered up and responding, enabling the interface when
nothing is connected results in a lot of error messages:
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 3 using ehci-platform
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 4 using ehci-platform
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high-speed USB device number 5 using ehci-platform
usb 2-1: device not accepting address 5, error -71
usb usb2-port1: unable to enumerate USB device
Disable it by default, but leave the entries in the board DTS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index d805cb50b5c8..ceb6ef15d669 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -112,7 +112,8 @@
};
&ehci1 {
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&ehci2 {
@@ -484,7 +485,8 @@
&usbphy2 {
phy-supply = <®_bldo4>;
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&usbphy3 {
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 8/8] ARM: dts: sun9i: a80-optimus: Disable EHCI1
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
EHCI1 provides an HSIC interface. This interface is exposed on the
board through two pins among the GPIO header.
With the PHY now powered up and responding, enabling the interface when
nothing is connected results in a lot of error messages:
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 3 using ehci-platform
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 4 using ehci-platform
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high-speed USB device number 5 using ehci-platform
usb 2-1: device not accepting address 5, error -71
usb usb2-port1: unable to enumerate USB device
Disable it by default, but leave the entries in the board DTS.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index d805cb50b5c8..ceb6ef15d669 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -112,7 +112,8 @@
};
&ehci1 {
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&ehci2 {
@@ -484,7 +485,8 @@
&usbphy2 {
phy-supply = <®_bldo4>;
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&usbphy3 {
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* [PATCH v2 8/8] ARM: dts: sun9i: a80-optimus: Disable EHCI1
@ 2016-08-27 7:55 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-08-27 7:55 UTC (permalink / raw)
To: linux-arm-kernel
EHCI1 provides an HSIC interface. This interface is exposed on the
board through two pins among the GPIO header.
With the PHY now powered up and responding, enabling the interface when
nothing is connected results in a lot of error messages:
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 3 using ehci-platform
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 4 using ehci-platform
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high-speed USB device number 5 using ehci-platform
usb 2-1: device not accepting address 5, error -71
usb usb2-port1: unable to enumerate USB device
Disable it by default, but leave the entries in the board DTS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1: none
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index d805cb50b5c8..ceb6ef15d669 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -112,7 +112,8 @@
};
&ehci1 {
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&ehci2 {
@@ -484,7 +485,8 @@
&usbphy2 {
phy-supply = <®_bldo4>;
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&usbphy3 {
--
2.9.3
^ permalink raw reply related [flat|nested] 58+ messages in thread
* Re: [PATCH v2 1/8] mfd: axp20x: Add bindings for AXP806 PMIC
@ 2016-08-31 12:11 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-08-31 12:11 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
On Sat, 27 Aug 2016, Chen-Yu Tsai wrote:
> This patch adds the basic and regulator bindings for the X-Powers AXP806
> PMIC.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes since v1: none
> ---
> Documentation/devicetree/bindings/mfd/axp20x.txt | 28 ++++++++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> index 585a95546288..8f3ad9ab4637 100644
> --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -10,7 +10,8 @@ axp809 (X-Powers)
>
> Required properties:
> - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
> - "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
> + "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
> + "x-powers,axp809"
> - reg: The I2C slave address or RSB hardware address for the AXP chip
> - interrupt-parent: The parent interrupt controller
> - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
> @@ -47,7 +48,6 @@ Optional properties for DCDC regulators:
> probably makes sense for HiFi audio related
> applications that aren't battery constrained.
>
> -
> AXP202/AXP209 regulators, type, and corresponding input supply names:
>
> Regulator Type Supply Name Notes
> @@ -86,6 +86,30 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
> RTC_LDO : LDO : ips-supply : always on
> DRIVEVBUS : Enable output : drivevbus-supply : external regulator
>
> +AXP806 regulators, type, and corresponding input supply names:
> +
> +Regulator Type Supply Name Notes
> +--------- ---- ----------- -----
> +DCDCA : DC-DC buck : vina-supply : poly-phase capable
> +DCDCB : DC-DC buck : vinb-supply : poly-phase capable
> +DCDCC : DC-DC buck : vinc-supply : poly-phase capable
> +DCDCD : DC-DC buck : vind-supply : poly-phase capable
> +DCDCE : DC-DC buck : vine-supply : poly-phase capable
> +ALDO1 : LDO : aldoin-supply : shared supply
> +ALDO2 : LDO : aldoin-supply : shared supply
> +ALDO3 : LDO : aldoin-supply : shared supply
> +BLDO1 : LDO : bldoin-supply : shared supply
> +BLDO2 : LDO : bldoin-supply : shared supply
> +BLDO3 : LDO : bldoin-supply : shared supply
> +BLDO4 : LDO : bldoin-supply : shared supply
> +CLDO1 : LDO : cldoin-supply : shared supply
> +CLDO2 : LDO : cldoin-supply : shared supply
> +CLDO3 : LDO : cldoin-supply : shared supply
> +SW : On/Off Switch : swin-supply
> +
> +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
> +for higher output current. The possible groupings are: A+B, A+B+C, D+E.
> +
> AXP809 regulators, type, and corresponding input supply names:
>
> Regulator Type Supply Name Notes
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 1/8] mfd: axp20x: Add bindings for AXP806 PMIC
@ 2016-08-31 12:11 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-08-31 12:11 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
On Sat, 27 Aug 2016, Chen-Yu Tsai wrote:
> This patch adds the basic and regulator bindings for the X-Powers AXP806
> PMIC.
>
> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> ---
> Changes since v1: none
> ---
> Documentation/devicetree/bindings/mfd/axp20x.txt | 28 ++++++++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> index 585a95546288..8f3ad9ab4637 100644
> --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -10,7 +10,8 @@ axp809 (X-Powers)
>
> Required properties:
> - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
> - "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
> + "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
> + "x-powers,axp809"
> - reg: The I2C slave address or RSB hardware address for the AXP chip
> - interrupt-parent: The parent interrupt controller
> - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
> @@ -47,7 +48,6 @@ Optional properties for DCDC regulators:
> probably makes sense for HiFi audio related
> applications that aren't battery constrained.
>
> -
> AXP202/AXP209 regulators, type, and corresponding input supply names:
>
> Regulator Type Supply Name Notes
> @@ -86,6 +86,30 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
> RTC_LDO : LDO : ips-supply : always on
> DRIVEVBUS : Enable output : drivevbus-supply : external regulator
>
> +AXP806 regulators, type, and corresponding input supply names:
> +
> +Regulator Type Supply Name Notes
> +--------- ---- ----------- -----
> +DCDCA : DC-DC buck : vina-supply : poly-phase capable
> +DCDCB : DC-DC buck : vinb-supply : poly-phase capable
> +DCDCC : DC-DC buck : vinc-supply : poly-phase capable
> +DCDCD : DC-DC buck : vind-supply : poly-phase capable
> +DCDCE : DC-DC buck : vine-supply : poly-phase capable
> +ALDO1 : LDO : aldoin-supply : shared supply
> +ALDO2 : LDO : aldoin-supply : shared supply
> +ALDO3 : LDO : aldoin-supply : shared supply
> +BLDO1 : LDO : bldoin-supply : shared supply
> +BLDO2 : LDO : bldoin-supply : shared supply
> +BLDO3 : LDO : bldoin-supply : shared supply
> +BLDO4 : LDO : bldoin-supply : shared supply
> +CLDO1 : LDO : cldoin-supply : shared supply
> +CLDO2 : LDO : cldoin-supply : shared supply
> +CLDO3 : LDO : cldoin-supply : shared supply
> +SW : On/Off Switch : swin-supply
> +
> +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
> +for higher output current. The possible groupings are: A+B, A+B+C, D+E.
> +
> AXP809 regulators, type, and corresponding input supply names:
>
> Regulator Type Supply Name Notes
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 1/8] mfd: axp20x: Add bindings for AXP806 PMIC
@ 2016-08-31 12:11 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-08-31 12:11 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, 27 Aug 2016, Chen-Yu Tsai wrote:
> This patch adds the basic and regulator bindings for the X-Powers AXP806
> PMIC.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes since v1: none
> ---
> Documentation/devicetree/bindings/mfd/axp20x.txt | 28 ++++++++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> index 585a95546288..8f3ad9ab4637 100644
> --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -10,7 +10,8 @@ axp809 (X-Powers)
>
> Required properties:
> - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
> - "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
> + "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
> + "x-powers,axp809"
> - reg: The I2C slave address or RSB hardware address for the AXP chip
> - interrupt-parent: The parent interrupt controller
> - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
> @@ -47,7 +48,6 @@ Optional properties for DCDC regulators:
> probably makes sense for HiFi audio related
> applications that aren't battery constrained.
>
> -
> AXP202/AXP209 regulators, type, and corresponding input supply names:
>
> Regulator Type Supply Name Notes
> @@ -86,6 +86,30 @@ LDO_IO1 : LDO : ips-supply : GPIO 1
> RTC_LDO : LDO : ips-supply : always on
> DRIVEVBUS : Enable output : drivevbus-supply : external regulator
>
> +AXP806 regulators, type, and corresponding input supply names:
> +
> +Regulator Type Supply Name Notes
> +--------- ---- ----------- -----
> +DCDCA : DC-DC buck : vina-supply : poly-phase capable
> +DCDCB : DC-DC buck : vinb-supply : poly-phase capable
> +DCDCC : DC-DC buck : vinc-supply : poly-phase capable
> +DCDCD : DC-DC buck : vind-supply : poly-phase capable
> +DCDCE : DC-DC buck : vine-supply : poly-phase capable
> +ALDO1 : LDO : aldoin-supply : shared supply
> +ALDO2 : LDO : aldoin-supply : shared supply
> +ALDO3 : LDO : aldoin-supply : shared supply
> +BLDO1 : LDO : bldoin-supply : shared supply
> +BLDO2 : LDO : bldoin-supply : shared supply
> +BLDO3 : LDO : bldoin-supply : shared supply
> +BLDO4 : LDO : bldoin-supply : shared supply
> +CLDO1 : LDO : cldoin-supply : shared supply
> +CLDO2 : LDO : cldoin-supply : shared supply
> +CLDO3 : LDO : cldoin-supply : shared supply
> +SW : On/Off Switch : swin-supply
> +
> +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
> +for higher output current. The possible groupings are: A+B, A+B+C, D+E.
> +
> AXP809 regulators, type, and corresponding input supply names:
>
> Regulator Type Supply Name Notes
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 2/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-31 12:12 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-08-31 12:12 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
On Sat, 27 Aug 2016, Chen-Yu Tsai wrote:
> The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
> SoC, along with a master AXP809 PMIC.
>
> This PMIC has a new register layout, and supports some functions not
> seen in other X-Powers PMICs, such as master-slave mode, or having
> multiple AXP806 PMICs on the same bus with address space extension,
> or supporting both I2C and RSB mode. I2C has not been tested.
>
> This patch adds support for the interrupts of the PMIC. A regulator
> sub-device is enabled, but actual regulator support will come in a
> later patch.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes since v1: none
> ---
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 60 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 133 insertions(+)
Applied, thanks.
> diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
> index a407527bcd09..a732cb50bcff 100644
> --- a/drivers/mfd/axp20x-rsb.c
> +++ b/drivers/mfd/axp20x-rsb.c
> @@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
>
> static const struct of_device_id axp20x_rsb_of_match[] = {
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
> { },
> };
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index fd80b0981f0f..96102753847f 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP806",
> "AXP809",
> };
>
> @@ -129,6 +130,27 @@ static const struct regmap_access_table axp288_volatile_table = {
> .n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
> };
>
> +static const struct regmap_range axp806_writeable_ranges[] = {
> + regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
> + regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
> + regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
> + regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> +};
> +
> +static const struct regmap_range axp806_volatile_ranges[] = {
> + regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> +};
> +
> +static const struct regmap_access_table axp806_writeable_table = {
> + .yes_ranges = axp806_writeable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp806_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table axp806_volatile_table = {
> + .yes_ranges = axp806_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp806_volatile_ranges),
> +};
> +
> static struct resource axp152_pek_resources[] = {
> DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
> DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
> @@ -278,6 +300,15 @@ static const struct regmap_config axp288_regmap_config = {
> .cache_type = REGCACHE_RBTREE,
> };
>
> +static const struct regmap_config axp806_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .wr_table = &axp806_writeable_table,
> + .volatile_table = &axp806_volatile_table,
> + .max_register = AXP806_VREF_TEMP_WARN_L,
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> #define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
> [_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
>
> @@ -409,6 +440,21 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp806_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
> + INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
> + INIT_REGMAP_IRQ(AXP806, DCDCA_V_LOW, 0, 3),
> + INIT_REGMAP_IRQ(AXP806, DCDCB_V_LOW, 0, 4),
> + INIT_REGMAP_IRQ(AXP806, DCDCC_V_LOW, 0, 5),
> + INIT_REGMAP_IRQ(AXP806, DCDCD_V_LOW, 0, 6),
> + INIT_REGMAP_IRQ(AXP806, DCDCE_V_LOW, 0, 7),
> + INIT_REGMAP_IRQ(AXP806, PWROK_LONG, 1, 0),
> + INIT_REGMAP_IRQ(AXP806, PWROK_SHORT, 1, 1),
> + INIT_REGMAP_IRQ(AXP806, WAKEUP, 1, 4),
> + INIT_REGMAP_IRQ(AXP806, PWROK_FALL, 1, 5),
> + INIT_REGMAP_IRQ(AXP806, PWROK_RISE, 1, 6),
> +};
> +
> static const struct regmap_irq axp809_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP809, ACIN_OVER_V, 0, 7),
> INIT_REGMAP_IRQ(AXP809, ACIN_PLUGIN, 0, 6),
> @@ -494,6 +540,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp806_regmap_irq_chip = {
> + .name = "axp806",
> + .status_base = AXP20X_IRQ1_STATE,
> + .ack_base = AXP20X_IRQ1_STATE,
> + .mask_base = AXP20X_IRQ1_EN,
> + .mask_invert = true,
> + .init_ack_masked = true,
> + .irqs = axp806_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp806_regmap_irqs),
> + .num_regs = 2,
> +};
> +
> static const struct regmap_irq_chip axp809_regmap_irq_chip = {
> .name = "axp809",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -660,12 +718,20 @@ static struct mfd_cell axp288_cells[] = {
> },
> };
>
> +static struct mfd_cell axp806_cells[] = {
> + {
> + .id = 2,
> + .name = "axp20x-regulator",
> + },
> +};
> +
> static struct mfd_cell axp809_cells[] = {
> {
> .name = "axp20x-pek",
> .num_resources = ARRAY_SIZE(axp809_pek_resources),
> .resources = axp809_pek_resources,
> }, {
> + .id = 1,
> .name = "axp20x-regulator",
> },
> };
> @@ -732,6 +798,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_cfg = &axp288_regmap_config;
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> break;
> + case AXP806_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
> + axp20x->cells = axp806_cells;
> + axp20x->regmap_cfg = &axp806_regmap_config;
> + axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
> + break;
> case AXP809_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
> axp20x->cells = axp809_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 0be4982f08fe..fec597fb34cb 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -20,6 +20,7 @@ enum {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP806_ID,
> AXP809_ID,
> NR_AXP20X_VARIANTS,
> };
> @@ -91,6 +92,30 @@ enum {
> #define AXP22X_ALDO3_V_OUT 0x2a
> #define AXP22X_CHRG_CTRL3 0x35
>
> +#define AXP806_STARTUP_SRC 0x00
> +#define AXP806_CHIP_ID 0x03
> +#define AXP806_PWR_OUT_CTRL1 0x10
> +#define AXP806_PWR_OUT_CTRL2 0x11
> +#define AXP806_DCDCA_V_CTRL 0x12
> +#define AXP806_DCDCB_V_CTRL 0x13
> +#define AXP806_DCDCC_V_CTRL 0x14
> +#define AXP806_DCDCD_V_CTRL 0x15
> +#define AXP806_DCDCE_V_CTRL 0x16
> +#define AXP806_ALDO1_V_CTRL 0x17
> +#define AXP806_ALDO2_V_CTRL 0x18
> +#define AXP806_ALDO3_V_CTRL 0x19
> +#define AXP806_DCDC_MODE_CTRL1 0x1a
> +#define AXP806_DCDC_MODE_CTRL2 0x1b
> +#define AXP806_DCDC_FREQ_CTRL 0x1c
> +#define AXP806_BLDO1_V_CTRL 0x20
> +#define AXP806_BLDO2_V_CTRL 0x21
> +#define AXP806_BLDO3_V_CTRL 0x22
> +#define AXP806_BLDO4_V_CTRL 0x23
> +#define AXP806_CLDO1_V_CTRL 0x24
> +#define AXP806_CLDO2_V_CTRL 0x25
> +#define AXP806_CLDO3_V_CTRL 0x26
> +#define AXP806_VREF_TEMP_WARN_L 0xf3
> +
> /* Interrupt */
> #define AXP152_IRQ1_EN 0x40
> #define AXP152_IRQ2_EN 0x41
> @@ -266,6 +291,26 @@ enum {
> };
>
> enum {
> + AXP806_DCDCA = 0,
> + AXP806_DCDCB,
> + AXP806_DCDCC,
> + AXP806_DCDCD,
> + AXP806_DCDCE,
> + AXP806_ALDO1,
> + AXP806_ALDO2,
> + AXP806_ALDO3,
> + AXP806_BLDO1,
> + AXP806_BLDO2,
> + AXP806_BLDO3,
> + AXP806_BLDO4,
> + AXP806_CLDO1,
> + AXP806_CLDO2,
> + AXP806_CLDO3,
> + AXP806_SW,
> + AXP806_REG_ID_MAX,
> +};
> +
> +enum {
> AXP809_DCDC1 = 0,
> AXP809_DCDC2,
> AXP809_DCDC3,
> @@ -414,6 +459,21 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp806_irqs {
> + AXP806_IRQ_DIE_TEMP_HIGH_LV1,
> + AXP806_IRQ_DIE_TEMP_HIGH_LV2,
> + AXP806_IRQ_DCDCA_V_LOW,
> + AXP806_IRQ_DCDCB_V_LOW,
> + AXP806_IRQ_DCDCC_V_LOW,
> + AXP806_IRQ_DCDCD_V_LOW,
> + AXP806_IRQ_DCDCE_V_LOW,
> + AXP806_IRQ_PWROK_LONG,
> + AXP806_IRQ_PWROK_SHORT,
> + AXP806_IRQ_WAKEUP,
> + AXP806_IRQ_PWROK_FALL,
> + AXP806_IRQ_PWROK_RISE,
> +};
> +
> enum axp809_irqs {
> AXP809_IRQ_ACIN_OVER_V = 1,
> AXP809_IRQ_ACIN_PLUGIN,
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 2/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-31 12:12 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-08-31 12:12 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
On Sat, 27 Aug 2016, Chen-Yu Tsai wrote:
> The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
> SoC, along with a master AXP809 PMIC.
>
> This PMIC has a new register layout, and supports some functions not
> seen in other X-Powers PMICs, such as master-slave mode, or having
> multiple AXP806 PMICs on the same bus with address space extension,
> or supporting both I2C and RSB mode. I2C has not been tested.
>
> This patch adds support for the interrupts of the PMIC. A regulator
> sub-device is enabled, but actual regulator support will come in a
> later patch.
>
> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> ---
> Changes since v1: none
> ---
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 60 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 133 insertions(+)
Applied, thanks.
> diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
> index a407527bcd09..a732cb50bcff 100644
> --- a/drivers/mfd/axp20x-rsb.c
> +++ b/drivers/mfd/axp20x-rsb.c
> @@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
>
> static const struct of_device_id axp20x_rsb_of_match[] = {
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
> { },
> };
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index fd80b0981f0f..96102753847f 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP806",
> "AXP809",
> };
>
> @@ -129,6 +130,27 @@ static const struct regmap_access_table axp288_volatile_table = {
> .n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
> };
>
> +static const struct regmap_range axp806_writeable_ranges[] = {
> + regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
> + regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
> + regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
> + regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> +};
> +
> +static const struct regmap_range axp806_volatile_ranges[] = {
> + regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> +};
> +
> +static const struct regmap_access_table axp806_writeable_table = {
> + .yes_ranges = axp806_writeable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp806_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table axp806_volatile_table = {
> + .yes_ranges = axp806_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp806_volatile_ranges),
> +};
> +
> static struct resource axp152_pek_resources[] = {
> DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
> DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
> @@ -278,6 +300,15 @@ static const struct regmap_config axp288_regmap_config = {
> .cache_type = REGCACHE_RBTREE,
> };
>
> +static const struct regmap_config axp806_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .wr_table = &axp806_writeable_table,
> + .volatile_table = &axp806_volatile_table,
> + .max_register = AXP806_VREF_TEMP_WARN_L,
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> #define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
> [_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
>
> @@ -409,6 +440,21 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp806_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
> + INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
> + INIT_REGMAP_IRQ(AXP806, DCDCA_V_LOW, 0, 3),
> + INIT_REGMAP_IRQ(AXP806, DCDCB_V_LOW, 0, 4),
> + INIT_REGMAP_IRQ(AXP806, DCDCC_V_LOW, 0, 5),
> + INIT_REGMAP_IRQ(AXP806, DCDCD_V_LOW, 0, 6),
> + INIT_REGMAP_IRQ(AXP806, DCDCE_V_LOW, 0, 7),
> + INIT_REGMAP_IRQ(AXP806, PWROK_LONG, 1, 0),
> + INIT_REGMAP_IRQ(AXP806, PWROK_SHORT, 1, 1),
> + INIT_REGMAP_IRQ(AXP806, WAKEUP, 1, 4),
> + INIT_REGMAP_IRQ(AXP806, PWROK_FALL, 1, 5),
> + INIT_REGMAP_IRQ(AXP806, PWROK_RISE, 1, 6),
> +};
> +
> static const struct regmap_irq axp809_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP809, ACIN_OVER_V, 0, 7),
> INIT_REGMAP_IRQ(AXP809, ACIN_PLUGIN, 0, 6),
> @@ -494,6 +540,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp806_regmap_irq_chip = {
> + .name = "axp806",
> + .status_base = AXP20X_IRQ1_STATE,
> + .ack_base = AXP20X_IRQ1_STATE,
> + .mask_base = AXP20X_IRQ1_EN,
> + .mask_invert = true,
> + .init_ack_masked = true,
> + .irqs = axp806_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp806_regmap_irqs),
> + .num_regs = 2,
> +};
> +
> static const struct regmap_irq_chip axp809_regmap_irq_chip = {
> .name = "axp809",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -660,12 +718,20 @@ static struct mfd_cell axp288_cells[] = {
> },
> };
>
> +static struct mfd_cell axp806_cells[] = {
> + {
> + .id = 2,
> + .name = "axp20x-regulator",
> + },
> +};
> +
> static struct mfd_cell axp809_cells[] = {
> {
> .name = "axp20x-pek",
> .num_resources = ARRAY_SIZE(axp809_pek_resources),
> .resources = axp809_pek_resources,
> }, {
> + .id = 1,
> .name = "axp20x-regulator",
> },
> };
> @@ -732,6 +798,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_cfg = &axp288_regmap_config;
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> break;
> + case AXP806_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
> + axp20x->cells = axp806_cells;
> + axp20x->regmap_cfg = &axp806_regmap_config;
> + axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
> + break;
> case AXP809_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
> axp20x->cells = axp809_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 0be4982f08fe..fec597fb34cb 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -20,6 +20,7 @@ enum {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP806_ID,
> AXP809_ID,
> NR_AXP20X_VARIANTS,
> };
> @@ -91,6 +92,30 @@ enum {
> #define AXP22X_ALDO3_V_OUT 0x2a
> #define AXP22X_CHRG_CTRL3 0x35
>
> +#define AXP806_STARTUP_SRC 0x00
> +#define AXP806_CHIP_ID 0x03
> +#define AXP806_PWR_OUT_CTRL1 0x10
> +#define AXP806_PWR_OUT_CTRL2 0x11
> +#define AXP806_DCDCA_V_CTRL 0x12
> +#define AXP806_DCDCB_V_CTRL 0x13
> +#define AXP806_DCDCC_V_CTRL 0x14
> +#define AXP806_DCDCD_V_CTRL 0x15
> +#define AXP806_DCDCE_V_CTRL 0x16
> +#define AXP806_ALDO1_V_CTRL 0x17
> +#define AXP806_ALDO2_V_CTRL 0x18
> +#define AXP806_ALDO3_V_CTRL 0x19
> +#define AXP806_DCDC_MODE_CTRL1 0x1a
> +#define AXP806_DCDC_MODE_CTRL2 0x1b
> +#define AXP806_DCDC_FREQ_CTRL 0x1c
> +#define AXP806_BLDO1_V_CTRL 0x20
> +#define AXP806_BLDO2_V_CTRL 0x21
> +#define AXP806_BLDO3_V_CTRL 0x22
> +#define AXP806_BLDO4_V_CTRL 0x23
> +#define AXP806_CLDO1_V_CTRL 0x24
> +#define AXP806_CLDO2_V_CTRL 0x25
> +#define AXP806_CLDO3_V_CTRL 0x26
> +#define AXP806_VREF_TEMP_WARN_L 0xf3
> +
> /* Interrupt */
> #define AXP152_IRQ1_EN 0x40
> #define AXP152_IRQ2_EN 0x41
> @@ -266,6 +291,26 @@ enum {
> };
>
> enum {
> + AXP806_DCDCA = 0,
> + AXP806_DCDCB,
> + AXP806_DCDCC,
> + AXP806_DCDCD,
> + AXP806_DCDCE,
> + AXP806_ALDO1,
> + AXP806_ALDO2,
> + AXP806_ALDO3,
> + AXP806_BLDO1,
> + AXP806_BLDO2,
> + AXP806_BLDO3,
> + AXP806_BLDO4,
> + AXP806_CLDO1,
> + AXP806_CLDO2,
> + AXP806_CLDO3,
> + AXP806_SW,
> + AXP806_REG_ID_MAX,
> +};
> +
> +enum {
> AXP809_DCDC1 = 0,
> AXP809_DCDC2,
> AXP809_DCDC3,
> @@ -414,6 +459,21 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp806_irqs {
> + AXP806_IRQ_DIE_TEMP_HIGH_LV1,
> + AXP806_IRQ_DIE_TEMP_HIGH_LV2,
> + AXP806_IRQ_DCDCA_V_LOW,
> + AXP806_IRQ_DCDCB_V_LOW,
> + AXP806_IRQ_DCDCC_V_LOW,
> + AXP806_IRQ_DCDCD_V_LOW,
> + AXP806_IRQ_DCDCE_V_LOW,
> + AXP806_IRQ_PWROK_LONG,
> + AXP806_IRQ_PWROK_SHORT,
> + AXP806_IRQ_WAKEUP,
> + AXP806_IRQ_PWROK_FALL,
> + AXP806_IRQ_PWROK_RISE,
> +};
> +
> enum axp809_irqs {
> AXP809_IRQ_ACIN_OVER_V = 1,
> AXP809_IRQ_ACIN_PLUGIN,
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 2/8] mfd: axp20x: Add support for AXP806 PMIC
@ 2016-08-31 12:12 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-08-31 12:12 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, 27 Aug 2016, Chen-Yu Tsai wrote:
> The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
> SoC, along with a master AXP809 PMIC.
>
> This PMIC has a new register layout, and supports some functions not
> seen in other X-Powers PMICs, such as master-slave mode, or having
> multiple AXP806 PMICs on the same bus with address space extension,
> or supporting both I2C and RSB mode. I2C has not been tested.
>
> This patch adds support for the interrupts of the PMIC. A regulator
> sub-device is enabled, but actual regulator support will come in a
> later patch.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes since v1: none
> ---
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 60 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 133 insertions(+)
Applied, thanks.
> diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
> index a407527bcd09..a732cb50bcff 100644
> --- a/drivers/mfd/axp20x-rsb.c
> +++ b/drivers/mfd/axp20x-rsb.c
> @@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
>
> static const struct of_device_id axp20x_rsb_of_match[] = {
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
> { },
> };
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index fd80b0981f0f..96102753847f 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -38,6 +38,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP806",
> "AXP809",
> };
>
> @@ -129,6 +130,27 @@ static const struct regmap_access_table axp288_volatile_table = {
> .n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
> };
>
> +static const struct regmap_range axp806_writeable_ranges[] = {
> + regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
> + regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
> + regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
> + regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> +};
> +
> +static const struct regmap_range axp806_volatile_ranges[] = {
> + regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> +};
> +
> +static const struct regmap_access_table axp806_writeable_table = {
> + .yes_ranges = axp806_writeable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp806_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table axp806_volatile_table = {
> + .yes_ranges = axp806_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp806_volatile_ranges),
> +};
> +
> static struct resource axp152_pek_resources[] = {
> DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
> DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
> @@ -278,6 +300,15 @@ static const struct regmap_config axp288_regmap_config = {
> .cache_type = REGCACHE_RBTREE,
> };
>
> +static const struct regmap_config axp806_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .wr_table = &axp806_writeable_table,
> + .volatile_table = &axp806_volatile_table,
> + .max_register = AXP806_VREF_TEMP_WARN_L,
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> #define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
> [_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
>
> @@ -409,6 +440,21 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp806_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
> + INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
> + INIT_REGMAP_IRQ(AXP806, DCDCA_V_LOW, 0, 3),
> + INIT_REGMAP_IRQ(AXP806, DCDCB_V_LOW, 0, 4),
> + INIT_REGMAP_IRQ(AXP806, DCDCC_V_LOW, 0, 5),
> + INIT_REGMAP_IRQ(AXP806, DCDCD_V_LOW, 0, 6),
> + INIT_REGMAP_IRQ(AXP806, DCDCE_V_LOW, 0, 7),
> + INIT_REGMAP_IRQ(AXP806, PWROK_LONG, 1, 0),
> + INIT_REGMAP_IRQ(AXP806, PWROK_SHORT, 1, 1),
> + INIT_REGMAP_IRQ(AXP806, WAKEUP, 1, 4),
> + INIT_REGMAP_IRQ(AXP806, PWROK_FALL, 1, 5),
> + INIT_REGMAP_IRQ(AXP806, PWROK_RISE, 1, 6),
> +};
> +
> static const struct regmap_irq axp809_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP809, ACIN_OVER_V, 0, 7),
> INIT_REGMAP_IRQ(AXP809, ACIN_PLUGIN, 0, 6),
> @@ -494,6 +540,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp806_regmap_irq_chip = {
> + .name = "axp806",
> + .status_base = AXP20X_IRQ1_STATE,
> + .ack_base = AXP20X_IRQ1_STATE,
> + .mask_base = AXP20X_IRQ1_EN,
> + .mask_invert = true,
> + .init_ack_masked = true,
> + .irqs = axp806_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp806_regmap_irqs),
> + .num_regs = 2,
> +};
> +
> static const struct regmap_irq_chip axp809_regmap_irq_chip = {
> .name = "axp809",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -660,12 +718,20 @@ static struct mfd_cell axp288_cells[] = {
> },
> };
>
> +static struct mfd_cell axp806_cells[] = {
> + {
> + .id = 2,
> + .name = "axp20x-regulator",
> + },
> +};
> +
> static struct mfd_cell axp809_cells[] = {
> {
> .name = "axp20x-pek",
> .num_resources = ARRAY_SIZE(axp809_pek_resources),
> .resources = axp809_pek_resources,
> }, {
> + .id = 1,
> .name = "axp20x-regulator",
> },
> };
> @@ -732,6 +798,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_cfg = &axp288_regmap_config;
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> break;
> + case AXP806_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
> + axp20x->cells = axp806_cells;
> + axp20x->regmap_cfg = &axp806_regmap_config;
> + axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
> + break;
> case AXP809_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
> axp20x->cells = axp809_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 0be4982f08fe..fec597fb34cb 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -20,6 +20,7 @@ enum {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP806_ID,
> AXP809_ID,
> NR_AXP20X_VARIANTS,
> };
> @@ -91,6 +92,30 @@ enum {
> #define AXP22X_ALDO3_V_OUT 0x2a
> #define AXP22X_CHRG_CTRL3 0x35
>
> +#define AXP806_STARTUP_SRC 0x00
> +#define AXP806_CHIP_ID 0x03
> +#define AXP806_PWR_OUT_CTRL1 0x10
> +#define AXP806_PWR_OUT_CTRL2 0x11
> +#define AXP806_DCDCA_V_CTRL 0x12
> +#define AXP806_DCDCB_V_CTRL 0x13
> +#define AXP806_DCDCC_V_CTRL 0x14
> +#define AXP806_DCDCD_V_CTRL 0x15
> +#define AXP806_DCDCE_V_CTRL 0x16
> +#define AXP806_ALDO1_V_CTRL 0x17
> +#define AXP806_ALDO2_V_CTRL 0x18
> +#define AXP806_ALDO3_V_CTRL 0x19
> +#define AXP806_DCDC_MODE_CTRL1 0x1a
> +#define AXP806_DCDC_MODE_CTRL2 0x1b
> +#define AXP806_DCDC_FREQ_CTRL 0x1c
> +#define AXP806_BLDO1_V_CTRL 0x20
> +#define AXP806_BLDO2_V_CTRL 0x21
> +#define AXP806_BLDO3_V_CTRL 0x22
> +#define AXP806_BLDO4_V_CTRL 0x23
> +#define AXP806_CLDO1_V_CTRL 0x24
> +#define AXP806_CLDO2_V_CTRL 0x25
> +#define AXP806_CLDO3_V_CTRL 0x26
> +#define AXP806_VREF_TEMP_WARN_L 0xf3
> +
> /* Interrupt */
> #define AXP152_IRQ1_EN 0x40
> #define AXP152_IRQ2_EN 0x41
> @@ -266,6 +291,26 @@ enum {
> };
>
> enum {
> + AXP806_DCDCA = 0,
> + AXP806_DCDCB,
> + AXP806_DCDCC,
> + AXP806_DCDCD,
> + AXP806_DCDCE,
> + AXP806_ALDO1,
> + AXP806_ALDO2,
> + AXP806_ALDO3,
> + AXP806_BLDO1,
> + AXP806_BLDO2,
> + AXP806_BLDO3,
> + AXP806_BLDO4,
> + AXP806_CLDO1,
> + AXP806_CLDO2,
> + AXP806_CLDO3,
> + AXP806_SW,
> + AXP806_REG_ID_MAX,
> +};
> +
> +enum {
> AXP809_DCDC1 = 0,
> AXP809_DCDC2,
> AXP809_DCDC3,
> @@ -414,6 +459,21 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp806_irqs {
> + AXP806_IRQ_DIE_TEMP_HIGH_LV1,
> + AXP806_IRQ_DIE_TEMP_HIGH_LV2,
> + AXP806_IRQ_DCDCA_V_LOW,
> + AXP806_IRQ_DCDCB_V_LOW,
> + AXP806_IRQ_DCDCC_V_LOW,
> + AXP806_IRQ_DCDCD_V_LOW,
> + AXP806_IRQ_DCDCE_V_LOW,
> + AXP806_IRQ_PWROK_LONG,
> + AXP806_IRQ_PWROK_SHORT,
> + AXP806_IRQ_WAKEUP,
> + AXP806_IRQ_PWROK_FALL,
> + AXP806_IRQ_PWROK_RISE,
> +};
> +
> enum axp809_irqs {
> AXP809_IRQ_ACIN_OVER_V = 1,
> AXP809_IRQ_ACIN_PLUGIN,
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-09-01 20:23 ` Mark Brown
0 siblings, 0 replies; 58+ messages in thread
From: Mark Brown @ 2016-09-01 20:23 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood,
Maxime Ripard, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 290 bytes --]
On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
> also a switch. The buck regulators support teaming into multi-phase
> groups, with A+B, A+B+C, D+E groupings.
Acked-by: Mark Brown <broonie@kernel.org>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 473 bytes --]
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-09-01 20:23 ` Mark Brown
0 siblings, 0 replies; 58+ messages in thread
From: Mark Brown @ 2016-09-01 20:23 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Lee Jones, Rob Herring, Mark Rutland, Liam Girdwood,
Maxime Ripard, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 318 bytes --]
On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
> also a switch. The buck regulators support teaming into multi-phase
> groups, with A+B, A+B+C, D+E groupings.
Acked-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-09-01 20:23 ` Mark Brown
0 siblings, 0 replies; 58+ messages in thread
From: Mark Brown @ 2016-09-01 20:23 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
> also a switch. The buck regulators support teaming into multi-phase
> groups, with A+B, A+B+C, D+E groupings.
Acked-by: Mark Brown <broonie@kernel.org>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160901/e32e5cfe/attachment.sig>
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
2016-09-01 20:23 ` Mark Brown
@ 2016-09-06 4:03 ` Chen-Yu Tsai
-1 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-06 4:03 UTC (permalink / raw)
To: Lee Jones
Cc: Chen-Yu Tsai, Mark Brown, Maxime Ripard, linux-arm-kernel, linux-kernel
Hi Lee,
On Fri, Sep 2, 2016 at 4:23 AM, Mark Brown <broonie@kernel.org> wrote:
> On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
>> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
>> also a switch. The buck regulators support teaming into multi-phase
>> groups, with A+B, A+B+C, D+E groupings.
>
> Acked-by: Mark Brown <broonie@kernel.org>
Could you merge this through the mfd tree, along with the AXP806
mfd patches?
Thanks
ChenYu
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-09-06 4:03 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-06 4:03 UTC (permalink / raw)
To: linux-arm-kernel
Hi Lee,
On Fri, Sep 2, 2016 at 4:23 AM, Mark Brown <broonie@kernel.org> wrote:
> On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
>> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
>> also a switch. The buck regulators support teaming into multi-phase
>> groups, with A+B, A+B+C, D+E groupings.
>
> Acked-by: Mark Brown <broonie@kernel.org>
Could you merge this through the mfd tree, along with the AXP806
mfd patches?
Thanks
ChenYu
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
2016-09-06 4:03 ` Chen-Yu Tsai
@ 2016-09-06 8:12 ` Lee Jones
-1 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-06 8:12 UTC (permalink / raw)
To: Chen-Yu Tsai; +Cc: Mark Brown, Maxime Ripard, linux-arm-kernel, linux-kernel
On Tue, 06 Sep 2016, Chen-Yu Tsai wrote:
> On Fri, Sep 2, 2016 at 4:23 AM, Mark Brown <broonie@kernel.org> wrote:
> > On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
> >> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
> >> also a switch. The buck regulators support teaming into multi-phase
> >> groups, with A+B, A+B+C, D+E groupings.
> >
> > Acked-by: Mark Brown <broonie@kernel.org>
>
> Could you merge this through the mfd tree, along with the AXP806
> mfd patches?
Yes, I've marked this patch as "TODO". Leave it with me.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 3/8] regulator: axp20x: support AXP806 variant
@ 2016-09-06 8:12 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-06 8:12 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, 06 Sep 2016, Chen-Yu Tsai wrote:
> On Fri, Sep 2, 2016 at 4:23 AM, Mark Brown <broonie@kernel.org> wrote:
> > On Sat, Aug 27, 2016 at 03:55:39PM +0800, Chen-Yu Tsai wrote:
> >> The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
> >> also a switch. The buck regulators support teaming into multi-phase
> >> groups, with A+B, A+B+C, D+E groupings.
> >
> > Acked-by: Mark Brown <broonie@kernel.org>
>
> Could you merge this through the mfd tree, along with the AXP806
> mfd patches?
Yes, I've marked this patch as "TODO". Leave it with me.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 12:02 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 12:02 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
Mark,
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-regulator-v4.9
for you to fetch changes up to 2ca342d391e3d8b56ed64626db8cfba8101b7c1d:
regulator: axp20x: Support AXP806 variant (2016-09-13 12:49:45 +0100)
----------------------------------------------------------------
Immutable branch between MFD and Regulator due for the v4.9 merge window
----------------------------------------------------------------
Chen-Yu Tsai (1):
regulator: axp20x: Support AXP806 variant
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++++++++++++++---
1 file changed, 111 insertions(+), 7 deletions(-)
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 12:02 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 12:02 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
Mark,
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-regulator-v4.9
for you to fetch changes up to 2ca342d391e3d8b56ed64626db8cfba8101b7c1d:
regulator: axp20x: Support AXP806 variant (2016-09-13 12:49:45 +0100)
----------------------------------------------------------------
Immutable branch between MFD and Regulator due for the v4.9 merge window
----------------------------------------------------------------
Chen-Yu Tsai (1):
regulator: axp20x: Support AXP806 variant
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++++++++++++++---
1 file changed, 111 insertions(+), 7 deletions(-)
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 58+ messages in thread
* [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 12:02 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 12:02 UTC (permalink / raw)
To: linux-arm-kernel
Mark,
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git tags/ib-mfd-regulator-v4.9
for you to fetch changes up to 2ca342d391e3d8b56ed64626db8cfba8101b7c1d:
regulator: axp20x: Support AXP806 variant (2016-09-13 12:49:45 +0100)
----------------------------------------------------------------
Immutable branch between MFD and Regulator due for the v4.9 merge window
----------------------------------------------------------------
Chen-Yu Tsai (1):
regulator: axp20x: Support AXP806 variant
drivers/regulator/axp20x-regulator.c | 118 ++++++++++++++++++++++++++++++++---
1 file changed, 111 insertions(+), 7 deletions(-)
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
2016-09-13 12:02 ` Lee Jones
(?)
@ 2016-09-13 13:04 ` Lee Jones
-1 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 13:04 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
Hold off on pulling this please Mark.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 13:04 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 13:04 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
Hold off on pulling this please Mark.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 58+ messages in thread
* [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 13:04 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 13:04 UTC (permalink / raw)
To: linux-arm-kernel
Hold off on pulling this please Mark.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
2016-09-13 12:02 ` Lee Jones
(?)
@ 2016-09-13 13:31 ` Lee Jones
-1 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 13:31 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
Mark,
Try this instead.
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-regulator-v4.9
for you to fetch changes up to 8824ee8573483e1c91691b5be3d3730e75551dce:
mfd: axp20x: Add support for AXP806 PMIC (2016-09-13 14:10:04 +0100)
----------------------------------------------------------------
Immutable branch between MFD and Regualtor due for the v4.9 merge window
----------------------------------------------------------------
Chen-Yu Tsai (3):
regulator: axp20x: Support AXP806 variant
mfd: axp20x: Add bindings for AXP806 PMIC
mfd: axp20x: Add support for AXP806 PMIC
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 ++++++++++++++
drivers/regulator/axp20x-regulator.c | 118 +++++++++++++++++++++--
include/linux/mfd/axp20x.h | 60 ++++++++++++
5 files changed, 270 insertions(+), 9 deletions(-)
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 13:31 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 13:31 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
Maxime Ripard, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
Mark,
Try this instead.
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-regulator-v4.9
for you to fetch changes up to 8824ee8573483e1c91691b5be3d3730e75551dce:
mfd: axp20x: Add support for AXP806 PMIC (2016-09-13 14:10:04 +0100)
----------------------------------------------------------------
Immutable branch between MFD and Regualtor due for the v4.9 merge window
----------------------------------------------------------------
Chen-Yu Tsai (3):
regulator: axp20x: Support AXP806 variant
mfd: axp20x: Add bindings for AXP806 PMIC
mfd: axp20x: Add support for AXP806 PMIC
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 ++++++++++++++
drivers/regulator/axp20x-regulator.c | 118 +++++++++++++++++++++--
include/linux/mfd/axp20x.h | 60 ++++++++++++
5 files changed, 270 insertions(+), 9 deletions(-)
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 58+ messages in thread
* [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 13:31 ` Lee Jones
0 siblings, 0 replies; 58+ messages in thread
From: Lee Jones @ 2016-09-13 13:31 UTC (permalink / raw)
To: linux-arm-kernel
Mark,
Try this instead.
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-regulator-v4.9
for you to fetch changes up to 8824ee8573483e1c91691b5be3d3730e75551dce:
mfd: axp20x: Add support for AXP806 PMIC (2016-09-13 14:10:04 +0100)
----------------------------------------------------------------
Immutable branch between MFD and Regualtor due for the v4.9 merge window
----------------------------------------------------------------
Chen-Yu Tsai (3):
regulator: axp20x: Support AXP806 variant
mfd: axp20x: Add bindings for AXP806 PMIC
mfd: axp20x: Add support for AXP806 PMIC
Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
drivers/mfd/axp20x-rsb.c | 1 +
drivers/mfd/axp20x.c | 72 ++++++++++++++
drivers/regulator/axp20x-regulator.c | 118 +++++++++++++++++++++--
include/linux/mfd/axp20x.h | 60 ++++++++++++
5 files changed, 270 insertions(+), 9 deletions(-)
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
2016-09-13 13:31 ` Lee Jones
(?)
@ 2016-09-13 14:45 ` Chen-Yu Tsai
-1 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-13 14:45 UTC (permalink / raw)
To: Lee Jones
Cc: Chen-Yu Tsai, Rob Herring, Mark Rutland, Liam Girdwood,
Mark Brown, Maxime Ripard, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
Hi Lee,
On Tue, Sep 13, 2016 at 9:31 PM, Lee Jones <lee.jones@linaro.org> wrote:
> Mark,
>
> Try this instead.
>
> The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
>
> Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-regulator-v4.9
>
> for you to fetch changes up to 8824ee8573483e1c91691b5be3d3730e75551dce:
>
> mfd: axp20x: Add support for AXP806 PMIC (2016-09-13 14:10:04 +0100)
>
> ----------------------------------------------------------------
> Immutable branch between MFD and Regualtor due for the v4.9 merge window
>
> ----------------------------------------------------------------
> Chen-Yu Tsai (3):
> regulator: axp20x: Support AXP806 variant
> mfd: axp20x: Add bindings for AXP806 PMIC
> mfd: axp20x: Add support for AXP806 PMIC
The mfd driver patch should come before the regulator patch for bisectability.
I'm guessing Mark is fine with you taking it through your tree though.
Thanks!
ChenYu
>
> Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 72 ++++++++++++++
> drivers/regulator/axp20x-regulator.c | 118 +++++++++++++++++++++--
> include/linux/mfd/axp20x.h | 60 ++++++++++++
> 5 files changed, 270 insertions(+), 9 deletions(-)
>
> --
> Lee Jones
> Linaro STMicroelectronics Landing Team Lead
> Linaro.org │ Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 14:45 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-13 14:45 UTC (permalink / raw)
To: Lee Jones
Cc: Chen-Yu Tsai, Rob Herring, Mark Rutland, Liam Girdwood,
Mark Brown, Maxime Ripard, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
Hi Lee,
On Tue, Sep 13, 2016 at 9:31 PM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
> Mark,
>
> Try this instead.
>
> The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
>
> Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-regulator-v4.9
>
> for you to fetch changes up to 8824ee8573483e1c91691b5be3d3730e75551dce:
>
> mfd: axp20x: Add support for AXP806 PMIC (2016-09-13 14:10:04 +0100)
>
> ----------------------------------------------------------------
> Immutable branch between MFD and Regualtor due for the v4.9 merge window
>
> ----------------------------------------------------------------
> Chen-Yu Tsai (3):
> regulator: axp20x: Support AXP806 variant
> mfd: axp20x: Add bindings for AXP806 PMIC
> mfd: axp20x: Add support for AXP806 PMIC
The mfd driver patch should come before the regulator patch for bisectability.
I'm guessing Mark is fine with you taking it through your tree though.
Thanks!
ChenYu
>
> Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 72 ++++++++++++++
> drivers/regulator/axp20x-regulator.c | 118 +++++++++++++++++++++--
> include/linux/mfd/axp20x.h | 60 ++++++++++++
> 5 files changed, 270 insertions(+), 9 deletions(-)
>
> --
> Lee Jones
> Linaro STMicroelectronics Landing Team Lead
> Linaro.org │ Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 58+ messages in thread
* [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window
@ 2016-09-13 14:45 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-13 14:45 UTC (permalink / raw)
To: linux-arm-kernel
Hi Lee,
On Tue, Sep 13, 2016 at 9:31 PM, Lee Jones <lee.jones@linaro.org> wrote:
> Mark,
>
> Try this instead.
>
> The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
>
> Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
>
> are available in the git repository at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-regulator-v4.9
>
> for you to fetch changes up to 8824ee8573483e1c91691b5be3d3730e75551dce:
>
> mfd: axp20x: Add support for AXP806 PMIC (2016-09-13 14:10:04 +0100)
>
> ----------------------------------------------------------------
> Immutable branch between MFD and Regualtor due for the v4.9 merge window
>
> ----------------------------------------------------------------
> Chen-Yu Tsai (3):
> regulator: axp20x: Support AXP806 variant
> mfd: axp20x: Add bindings for AXP806 PMIC
> mfd: axp20x: Add support for AXP806 PMIC
The mfd driver patch should come before the regulator patch for bisectability.
I'm guessing Mark is fine with you taking it through your tree though.
Thanks!
ChenYu
>
> Documentation/devicetree/bindings/mfd/axp20x.txt | 28 +++++-
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 72 ++++++++++++++
> drivers/regulator/axp20x-regulator.c | 118 +++++++++++++++++++++--
> include/linux/mfd/axp20x.h | 60 ++++++++++++
> 5 files changed, 270 insertions(+), 9 deletions(-)
>
> --
> Lee Jones
> Linaro STMicroelectronics Landing Team Lead
> Linaro.org ? Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-09-15 14:33 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-15 14:33 UTC (permalink / raw)
To: Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Chen-Yu Tsai
Hi Maxime,
On Sat, Aug 27, 2016 at 3:55 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> The AXP806 PMIC is the secondary PMIC. It provides various supply
> voltages for the SoC and other peripherals. The PMIC's interrupt
> line is connected to NMI pin of the SoC.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The driver patches have all been merged into the mfd tree. Could
you queue up the dts patches?
Thanks
ChenYu
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-09-15 14:33 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-15 14:33 UTC (permalink / raw)
To: Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Chen-Yu Tsai
Hi Maxime,
On Sat, Aug 27, 2016 at 3:55 PM, Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org> wrote:
> The AXP806 PMIC is the secondary PMIC. It provides various supply
> voltages for the SoC and other peripherals. The PMIC's interrupt
> line is connected to NMI pin of the SoC.
>
> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
The driver patches have all been merged into the mfd tree. Could
you queue up the dts patches?
Thanks
ChenYu
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-09-15 14:33 ` Chen-Yu Tsai
0 siblings, 0 replies; 58+ messages in thread
From: Chen-Yu Tsai @ 2016-09-15 14:33 UTC (permalink / raw)
To: linux-arm-kernel
Hi Maxime,
On Sat, Aug 27, 2016 at 3:55 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> The AXP806 PMIC is the secondary PMIC. It provides various supply
> voltages for the SoC and other peripherals. The PMIC's interrupt
> line is connected to NMI pin of the SoC.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The driver patches have all been merged into the mfd tree. Could
you queue up the dts patches?
Thanks
ChenYu
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-09-15 14:56 ` Maxime Ripard
0 siblings, 0 replies; 58+ messages in thread
From: Maxime Ripard @ 2016-09-15 14:56 UTC (permalink / raw)
To: Chen-Yu Tsai; +Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 655 bytes --]
On Thu, Sep 15, 2016 at 10:33:50PM +0800, Chen-Yu Tsai wrote:
> Hi Maxime,
>
> On Sat, Aug 27, 2016 at 3:55 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> > The AXP806 PMIC is the secondary PMIC. It provides various supply
> > voltages for the SoC and other peripherals. The PMIC's interrupt
> > line is connected to NMI pin of the SoC.
> >
> > Signed-off-by: Chen-Yu Tsai <wens@csie.org>
>
> The driver patches have all been merged into the mfd tree. Could
> you queue up the dts patches?
I just did.
Thanks for the remainder,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 58+ messages in thread
* Re: [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-09-15 14:56 ` Maxime Ripard
0 siblings, 0 replies; 58+ messages in thread
From: Maxime Ripard @ 2016-09-15 14:56 UTC (permalink / raw)
To: Chen-Yu Tsai; +Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 672 bytes --]
On Thu, Sep 15, 2016 at 10:33:50PM +0800, Chen-Yu Tsai wrote:
> Hi Maxime,
>
> On Sat, Aug 27, 2016 at 3:55 PM, Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org> wrote:
> > The AXP806 PMIC is the secondary PMIC. It provides various supply
> > voltages for the SoC and other peripherals. The PMIC's interrupt
> > line is connected to NMI pin of the SoC.
> >
> > Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>
> The driver patches have all been merged into the mfd tree. Could
> you queue up the dts patches?
I just did.
Thanks for the remainder,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 58+ messages in thread
* [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
@ 2016-09-15 14:56 ` Maxime Ripard
0 siblings, 0 replies; 58+ messages in thread
From: Maxime Ripard @ 2016-09-15 14:56 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Sep 15, 2016 at 10:33:50PM +0800, Chen-Yu Tsai wrote:
> Hi Maxime,
>
> On Sat, Aug 27, 2016 at 3:55 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> > The AXP806 PMIC is the secondary PMIC. It provides various supply
> > voltages for the SoC and other peripherals. The PMIC's interrupt
> > line is connected to NMI pin of the SoC.
> >
> > Signed-off-by: Chen-Yu Tsai <wens@csie.org>
>
> The driver patches have all been merged into the mfd tree. Could
> you queue up the dts patches?
I just did.
Thanks for the remainder,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160915/7d725958/attachment.sig>
^ permalink raw reply [flat|nested] 58+ messages in thread
end of thread, other threads:[~2016-09-15 14:56 UTC | newest]
Thread overview: 58+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-08-27 7:55 [PATCH v2 0/8] mfd: axp20x: Add support for AXP806 PMIC Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` [PATCH v2 1/8] mfd: axp20x: Add bindings " Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-31 12:11 ` Lee Jones
2016-08-31 12:11 ` Lee Jones
2016-08-31 12:11 ` Lee Jones
2016-08-27 7:55 ` [PATCH v2 2/8] mfd: axp20x: Add support " Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-31 12:12 ` Lee Jones
2016-08-31 12:12 ` Lee Jones
2016-08-31 12:12 ` Lee Jones
2016-08-27 7:55 ` [PATCH v2 3/8] regulator: axp20x: support AXP806 variant Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-09-01 20:23 ` Mark Brown
2016-09-01 20:23 ` Mark Brown
2016-09-01 20:23 ` Mark Brown
2016-09-06 4:03 ` Chen-Yu Tsai
2016-09-06 4:03 ` Chen-Yu Tsai
2016-09-06 8:12 ` Lee Jones
2016-09-06 8:12 ` Lee Jones
2016-09-13 12:02 ` [GIT PULL] Immutable branch between MFD and Regulator due for the v4.9 merge window Lee Jones
2016-09-13 12:02 ` Lee Jones
2016-09-13 12:02 ` Lee Jones
2016-09-13 13:04 ` Lee Jones
2016-09-13 13:04 ` Lee Jones
2016-09-13 13:04 ` Lee Jones
2016-09-13 13:31 ` Lee Jones
2016-09-13 13:31 ` Lee Jones
2016-09-13 13:31 ` Lee Jones
2016-09-13 14:45 ` Chen-Yu Tsai
2016-09-13 14:45 ` Chen-Yu Tsai
2016-09-13 14:45 ` Chen-Yu Tsai
2016-08-27 7:55 ` [PATCH v2 4/8] ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` [PATCH v2 5/8] ARM: dts: sun9i: cubieboard4: " Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` [PATCH v2 6/8] ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-09-15 14:33 ` Chen-Yu Tsai
2016-09-15 14:33 ` Chen-Yu Tsai
2016-09-15 14:33 ` Chen-Yu Tsai
2016-09-15 14:56 ` Maxime Ripard
2016-09-15 14:56 ` Maxime Ripard
2016-09-15 14:56 ` Maxime Ripard
2016-08-27 7:55 ` [PATCH v2 7/8] ARM: dts: sun9i: cubieboard4: " Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` [PATCH v2 8/8] ARM: dts: sun9i: a80-optimus: Disable EHCI1 Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
2016-08-27 7:55 ` Chen-Yu Tsai
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.