[PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[Icenowy Zheng]

Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.

Enable the USB host controller.

The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
---
Changes in v2:
- Added Chen-Yu's review tag.

 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index ba2fde2909f9..a4a7b9cb59b9 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -68,6 +68,10 @@
 	};
 };
 
+&ehci1 {
+	status = "okay";
+};
+
 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
@@ -123,6 +127,10 @@
 	status = "okay";
 };
 
+&ohci1 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
@@ -134,3 +142,7 @@
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
 	status = "okay";
 };
+
+&usbphy {
+	status = "okay";
+};
-- 
2.13.0

[PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[Icenowy Zheng]

Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.

Enable the USB host controller.

The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.

Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
Reviewed-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
Changes in v2:
- Added Chen-Yu's review tag.

 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index ba2fde2909f9..a4a7b9cb59b9 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -68,6 +68,10 @@
 	};
 };
 
+&ehci1 {
+	status = "okay";
+};
+
 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
@@ -123,6 +127,10 @@
 	status = "okay";
 };
 
+&ohci1 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
@@ -134,3 +142,7 @@
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
 	status = "okay";
 };
+
+&usbphy {
+	status = "okay";
+};
-- 
2.13.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[Icenowy Zheng]

Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.

Enable the USB host controller.

The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
---
Changes in v2:
- Added Chen-Yu's review tag.

 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index ba2fde2909f9..a4a7b9cb59b9 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -68,6 +68,10 @@
 	};
 };
 
+&ehci1 {
+	status = "okay";
+};
+
 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
@@ -123,6 +127,10 @@
 	status = "okay";
 };
 
+&ohci1 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
@@ -134,3 +142,7 @@
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
 	status = "okay";
 };
+
+&usbphy {
+	status = "okay";
+};
-- 
2.13.0

[PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Icenowy Zheng]

Banana Pi M64 board uses an AXP803 PMIC.

Enable the PMIC and its regulators.

As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v2:
- Changed vdd-cpux constraints.
- Added vcc-1v2-hsic regulator.

 .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 122 +++++++++++++++++++--
 1 file changed, 112 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index a4a7b9cb59b9..ec72ca8c8b30 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,13 +59,6 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci1 {
@@ -77,6 +70,7 @@
 	pinctrl-0 = <&rgmii_pins>;
 	phy-mode = "rgmii";
 	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
 	status = "okay";
 };
 
@@ -100,7 +94,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 	disable-wp;
@@ -111,7 +105,8 @@
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dldo2>;
+	vqmmc-supply = <&reg_dldo4>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
@@ -120,7 +115,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -131,6 +126,113 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
-- 
2.13.0

[PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Icenowy Zheng]

Banana Pi M64 board uses an AXP803 PMIC.

Enable the PMIC and its regulators.

As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.

Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
---
Changes in v2:
- Changed vdd-cpux constraints.
- Added vcc-1v2-hsic regulator.

 .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 122 +++++++++++++++++++--
 1 file changed, 112 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index a4a7b9cb59b9..ec72ca8c8b30 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,13 +59,6 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci1 {
@@ -77,6 +70,7 @@
 	pinctrl-0 = <&rgmii_pins>;
 	phy-mode = "rgmii";
 	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
 	status = "okay";
 };
 
@@ -100,7 +94,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 	disable-wp;
@@ -111,7 +105,8 @@
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dldo2>;
+	vqmmc-supply = <&reg_dldo4>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
@@ -120,7 +115,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -131,6 +126,113 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
-- 
2.13.0

[PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Icenowy Zheng]

Banana Pi M64 board uses an AXP803 PMIC.

Enable the PMIC and its regulators.

As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v2:
- Changed vdd-cpux constraints.
- Added vcc-1v2-hsic regulator.

 .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 122 +++++++++++++++++++--
 1 file changed, 112 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index a4a7b9cb59b9..ec72ca8c8b30 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,13 +59,6 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci1 {
@@ -77,6 +70,7 @@
 	pinctrl-0 = <&rgmii_pins>;
 	phy-mode = "rgmii";
 	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
 	status = "okay";
 };
 
@@ -100,7 +94,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 	disable-wp;
@@ -111,7 +105,8 @@
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dldo2>;
+	vqmmc-supply = <&reg_dldo4>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
@@ -120,7 +115,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -131,6 +126,113 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic at 3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
-- 
2.13.0

[PATCH v2 3/3] arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64

[Icenowy Zheng]

BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.

The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.

Fix these issues for proper Wi-Fi support of BPi M64.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index ec72ca8c8b30..4a8d3f83a36e 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,6 +59,11 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
 };
 
 &ehci1 {
@@ -107,9 +112,18 @@
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&reg_dldo2>;
 	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc2 {
-- 
2.13.0

[PATCH v2 3/3] arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64

[Icenowy Zheng]

BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.

The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.

Fix these issues for proper Wi-Fi support of BPi M64.

Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index ec72ca8c8b30..4a8d3f83a36e 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,6 +59,11 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
 };
 
 &ehci1 {
@@ -107,9 +112,18 @@
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&reg_dldo2>;
 	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc2 {
-- 
2.13.0

[PATCH v2 3/3] arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64

[Icenowy Zheng]

BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.

The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.

Fix these issues for proper Wi-Fi support of BPi M64.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index ec72ca8c8b30..4a8d3f83a36e 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,6 +59,11 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
 };
 
 &ehci1 {
@@ -107,9 +112,18 @@
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&reg_dldo2>;
 	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc2 {
-- 
2.13.0

Re: [linux-sunxi] [PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
> hub, which provided the two USB Type-A ports on the board.
>
> Enable the USB host controller.
>
> The OTG function of the Micro-USB port needs the drivevbus function of
> the AXP803 driver implemented, so it's not enabled now.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>

Applied for 4.14.

Thanks.

Re: [PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org> wrote:
> Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
> hub, which provided the two USB Type-A ports on the board.
>
> Enable the USB host controller.
>
> The OTG function of the Micro-USB port needs the drivevbus function of
> the AXP803 driver implemented, so it's not enabled now.
>
> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
> Reviewed-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>

Applied for 4.14.

Thanks.

[linux-sunxi] [PATCH v2 1/3] arm64: allwinner: a64: enable USB host controller for BPi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
> hub, which provided the two USB Type-A ports on the board.
>
> Enable the USB host controller.
>
> The OTG function of the Micro-USB port needs the drivevbus function of
> the AXP803 driver implemented, so it's not enabled now.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>

Applied for 4.14.

Thanks.

Re: [linux-sunxi] [PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Banana Pi M64 board uses an AXP803 PMIC.
>
> Enable the PMIC and its regulators.
>
> As we have now proper regulators support, missing or dummy regulators
> are changed to the correct ones.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Applied for 4.14.

Thanks.

Re: [linux-sunxi] [PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org> wrote:
> Banana Pi M64 board uses an AXP803 PMIC.
>
> Enable the PMIC and its regulators.
>
> As we have now proper regulators support, missing or dummy regulators
> are changed to the correct ones.
>
> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>

Applied for 4.14.

Thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[linux-sunxi] [PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Banana Pi M64 board uses an AXP803 PMIC.
>
> Enable the PMIC and its regulators.
>
> As we have now proper regulators support, missing or dummy regulators
> are changed to the correct ones.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Applied for 4.14.

Thanks.

Re: [linux-sunxi] [PATCH v2 3/3] arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
> card is connected to the mmc1 controller.
>
> The pwrseq of the mmc1 (used to reset the card) used to missing, and the
> out-of-band interrupt line of the card is not specified.
>
> Fix these issues for proper Wi-Fi support of BPi M64.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Applied for 4.14.

Thanks.

Re: [linux-sunxi] [PATCH v2 3/3] arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org> wrote:
> BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
> card is connected to the mmc1 controller.
>
> The pwrseq of the mmc1 (used to reset the card) used to missing, and the
> out-of-band interrupt line of the card is not specified.
>
> Fix these issues for proper Wi-Fi support of BPi M64.
>
> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>

Applied for 4.14.

Thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[linux-sunxi] [PATCH v2 3/3] arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64

[Chen-Yu Tsai]

On Tue, Jul 25, 2017 at 8:45 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
> card is connected to the mmc1 controller.
>
> The pwrseq of the mmc1 (used to reset the card) used to missing, and the
> out-of-band interrupt line of the card is not specified.
>
> Fix these issues for proper Wi-Fi support of BPi M64.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Applied for 4.14.

Thanks.