[PATCH V2 01/24] phy: nop-phy: Add standard usb-nop-xceiv compat string

[PATCH V2 01/24] phy: nop-phy: Add standard usb-nop-xceiv compat string

[Marek Vasut]

The USB no-op PHY uses "usb-nop-xceiv" compatible string. This driver is
compatible with USB no-op PHY, so add the compatible string.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/phy/nop-phy.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/phy/nop-phy.c b/drivers/phy/nop-phy.c
index 84aac80623..9f12ebc062 100644
--- a/drivers/phy/nop-phy.c
+++ b/drivers/phy/nop-phy.c
@@ -43,6 +43,7 @@ static int nop_phy_probe(struct udevice *dev)
 
 static const struct udevice_id nop_phy_ids[] = {
 	{ .compatible = "nop-phy" },
+	{ .compatible = "usb-nop-xceiv" },
 	{ }
 };
 
-- 
2.30.2

[PATCH V2 02/24] arc: emsdp/iotdk: Use standard compatible string for USB no-op PHY

[Marek Vasut]

The standard compatible string is "usb-nop-xceiv", use it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 arch/arc/dts/iot_devkit.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arc/dts/iot_devkit.dts b/arch/arc/dts/iot_devkit.dts
index c0173fa5ab..2122827527 100644
--- a/arch/arc/dts/iot_devkit.dts
+++ b/arch/arc/dts/iot_devkit.dts
@@ -39,7 +39,7 @@
 	};
 
 	usbphy: phy {
-		compatible = "nop-phy";
+		compatible = "usb-nop-xceiv";
 		#phy-cells = <0>;
 	};
 
-- 
2.30.2

[PATCH V2 03/24] ARM: dts: k2g-evm: Use standard compatible string for USB no-op PHY

[Marek Vasut]

The standard compatible string is "usb-nop-xceiv", use it.
Note that keystone-k2g.dtsi already uses the aforementioned
compat string, so this patch can only remove the override.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 arch/arm/dts/keystone-k2g-evm.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/dts/keystone-k2g-evm.dts b/arch/arm/dts/keystone-k2g-evm.dts
index 7c5deef808..b5b511cbd6 100644
--- a/arch/arm/dts/keystone-k2g-evm.dts
+++ b/arch/arm/dts/keystone-k2g-evm.dts
@@ -38,7 +38,6 @@
 
 &usb0_phy {
 	status = "okay";
-	compatible = "nop-phy";
 };
 
 &usb0 {
@@ -51,7 +50,6 @@
 };
 
 &usb1_phy {
-	compatible = "nop-phy";
 	status = "okay";
 };
 
-- 
2.30.2

[PATCH V2 04/24] ARM: dts: imx8mm: Replace deprecated fsl, usbphy DT props with phys

[Marek Vasut]

The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: Isolate to iMX8MM
---
 arch/arm/dts/imx8mm.dtsi | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm/dts/imx8mm.dtsi b/arch/arm/dts/imx8mm.dtsi
index c824f2615f..fa2d73f180 100644
--- a/arch/arm/dts/imx8mm.dtsi
+++ b/arch/arm/dts/imx8mm.dtsi
@@ -241,6 +241,7 @@
 	};
 
 	usbphynop1: usbphynop1 {
+		#phy-cells = <0>;
 		compatible = "usb-nop-xceiv";
 		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
 		assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -249,6 +250,7 @@
 	};
 
 	usbphynop2: usbphynop2 {
+		#phy-cells = <0>;
 		compatible = "usb-nop-xceiv";
 		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
 		assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -936,7 +938,7 @@
 				clock-names = "usb1_ctrl_root_clk";
 				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
-				fsl,usbphy = <&usbphynop1>;
+				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
 				status = "disabled";
 			};
@@ -955,7 +957,7 @@
 				clock-names = "usb1_ctrl_root_clk";
 				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
-				fsl,usbphy = <&usbphynop2>;
+				phys = <&usbphynop2>;
 				fsl,usbmisc = <&usbmisc2 0>;
 				status = "disabled";
 			};
-- 
2.30.2

[PATCH V2 05/24] ARM: dts: imx8mn: Replace deprecated fsl, usbphy DT props with phys

[Marek Vasut]

The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: New patch for iMX8MN
---
 arch/arm/dts/imx8mn.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/dts/imx8mn.dtsi b/arch/arm/dts/imx8mn.dtsi
index 16ea500895..63005ce9d1 100644
--- a/arch/arm/dts/imx8mn.dtsi
+++ b/arch/arm/dts/imx8mn.dtsi
@@ -962,7 +962,7 @@
 				clock-names = "usb1_ctrl_root_clk";
 				assigned-clocks = <&clk IMX8MN_CLK_USB_BUS>;
 				assigned-clock-parents = <&clk IMX8MN_SYS_PLL2_500M>;
-				fsl,usbphy = <&usbphynop1>;
+				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
 				status = "disabled";
 			};
@@ -1030,6 +1030,7 @@
 	};
 
 	usbphynop1: usbphynop1 {
+		#phy-cells = <0>;
 		compatible = "usb-nop-xceiv";
 		clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
 		assigned-clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
-- 
2.30.2

[PATCH V2 06/24] ARM: dts: imx8mm: Add power domain nodes

[Marek Vasut]

Add power domain nodes to DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 arch/arm/dts/imx8mm.dtsi                 | 73 ++++++++++++++++++++++++
 include/dt-bindings/power/imx8mm-power.h | 22 +++++++
 2 files changed, 95 insertions(+)
 create mode 100644 include/dt-bindings/power/imx8mm-power.h

diff --git a/arch/arm/dts/imx8mm.dtsi b/arch/arm/dts/imx8mm.dtsi
index fa2d73f180..b142b80734 100644
--- a/arch/arm/dts/imx8mm.dtsi
+++ b/arch/arm/dts/imx8mm.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/clock/imx8mm-clock.h>
+#include <dt-bindings/power/imx8mm-power.h>
+#include <dt-bindings/reset/imx8mq-reset.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -592,6 +594,75 @@
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
 			};
+
+			gpc: gpc at 303a0000 {
+				compatible = "fsl,imx8mm-gpc";
+				reg = <0x303a0000 0x10000>;
+				interrupt-parent = <&gic>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pgc_hsiomix: power-domain at 0 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_HSIOMIX>;
+						clocks = <&clk IMX8MM_CLK_USB_BUS>;
+					};
+
+					pgc_pcie: power-domain at 1 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_PCIE>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_otg1: power-domain at 2 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_OTG1>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_otg2: power-domain at 3 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_OTG2>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_gpumix: power-domain at 4 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_GPUMIX>;
+						clocks = <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+						         <&clk IMX8MM_CLK_GPU_AHB>;
+					};
+
+					pgc_gpu: power-domain at 5 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_GPU>;
+						clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+						         <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+						         <&clk IMX8MM_CLK_GPU2D_ROOT>,
+						         <&clk IMX8MM_CLK_GPU3D_ROOT>;
+						resets = <&src IMX8MQ_RESET_GPU_RESET>;
+						power-domains = <&pgc_gpumix>;
+					};
+
+					dispmix_pd: power-domain at 10 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_DISPMIX>;
+						clocks = <&clk IMX8MM_CLK_DISP_ROOT>,
+							 <&clk IMX8MM_CLK_DISP_AXI_ROOT>,
+							 <&clk IMX8MM_CLK_DISP_APB_ROOT>;
+					};
+
+					mipi_pd: power-domain at 11 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_MIPI>;
+						power-domains = <&dispmix_pd>;
+					};
+				};
+			};
 		};
 
 		aips2: bus at 30400000 {
@@ -940,6 +1011,7 @@
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
+				power-domains = <&pgc_otg1>;
 				status = "disabled";
 			};
 
@@ -959,6 +1031,7 @@
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop2>;
 				fsl,usbmisc = <&usbmisc2 0>;
+				power-domains = <&pgc_otg2>;
 				status = "disabled";
 			};
 
diff --git a/include/dt-bindings/power/imx8mm-power.h b/include/dt-bindings/power/imx8mm-power.h
new file mode 100644
index 0000000000..fc9c2e16aa
--- /dev/null
+++ b/include/dt-bindings/power/imx8mm-power.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/*
+ *  Copyright (C) 2020 Pengutronix, Lucas Stach <kernel@pengutronix.de>
+ */
+
+#ifndef __DT_BINDINGS_IMX8MM_POWER_H__
+#define __DT_BINDINGS_IMX8MM_POWER_H__
+
+#define IMX8MM_POWER_DOMAIN_HSIOMIX	0
+#define IMX8MM_POWER_DOMAIN_PCIE	1
+#define IMX8MM_POWER_DOMAIN_OTG1	2
+#define IMX8MM_POWER_DOMAIN_OTG2	3
+#define IMX8MM_POWER_DOMAIN_GPUMIX	4
+#define IMX8MM_POWER_DOMAIN_GPU		5
+#define IMX8MM_POWER_DOMAIN_VPUMIX	6
+#define IMX8MM_POWER_DOMAIN_VPUG1	7
+#define IMX8MM_POWER_DOMAIN_VPUG2	8
+#define IMX8MM_POWER_DOMAIN_VPUH1	9
+#define IMX8MM_POWER_DOMAIN_DISPMIX	10
+#define IMX8MM_POWER_DOMAIN_MIPI	11
+
+#endif
-- 
2.30.2

[PATCH V2 07/24] ARM: dts: imx8mn: Add power domain nodes

[Marek Vasut]

Add power domain nodes to DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: New patch
---
 arch/arm/dts/imx8mn.dtsi                 | 51 ++++++++++++++++++++++++
 include/dt-bindings/power/imx8mn-power.h | 15 +++++++
 2 files changed, 66 insertions(+)
 create mode 100644 include/dt-bindings/power/imx8mn-power.h

diff --git a/arch/arm/dts/imx8mn.dtsi b/arch/arm/dts/imx8mn.dtsi
index 63005ce9d1..edcb415b53 100644
--- a/arch/arm/dts/imx8mn.dtsi
+++ b/arch/arm/dts/imx8mn.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/clock/imx8mn-clock.h>
+#include <dt-bindings/power/imx8mn-power.h>
+#include <dt-bindings/reset/imx8mq-reset.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -612,6 +614,54 @@
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
 			};
+
+			gpc: gpc at 303a0000 {
+				compatible = "fsl,imx8mn-gpc";
+				reg = <0x303a0000 0x10000>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pgc_hsiomix: power-domain at 0 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_HSIOMIX>;
+						clocks = <&clk IMX8MN_CLK_USB_BUS>;
+					};
+
+					pgc_otg1: power-domain at 1 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_OTG1>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_gpumix: power-domain at 2 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_GPUMIX>;
+						clocks = <&clk IMX8MN_CLK_GPU_CORE_ROOT>,
+							 <&clk IMX8MN_CLK_GPU_SHADER_DIV>,
+							 <&clk IMX8MN_CLK_GPU_BUS_ROOT>,
+							 <&clk IMX8MN_CLK_GPU_AHB>;
+						resets = <&src IMX8MQ_RESET_GPU_RESET>;
+					};
+
+					dispmix_pd: power-domain at 3 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_DISPMIX>;
+						clocks = <&clk IMX8MN_CLK_DISP_PIXEL_ROOT>,
+							 <&clk IMX8MN_CLK_DISP_AXI_ROOT>,
+							 <&clk IMX8MN_CLK_DISP_APB_ROOT>;
+					};
+
+					mipi_pd: power-domain at 4 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_MIPI>;
+						power-domains = <&dispmix_pd>;
+					};
+				};
+			};
 		};
 
 		aips2: bus at 30400000 {
@@ -964,6 +1014,7 @@
 				assigned-clock-parents = <&clk IMX8MN_SYS_PLL2_500M>;
 				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
+				power-domains = <&pgc_otg1>;
 				status = "disabled";
 			};
 
diff --git a/include/dt-bindings/power/imx8mn-power.h b/include/dt-bindings/power/imx8mn-power.h
new file mode 100644
index 0000000000..102ee85a9b
--- /dev/null
+++ b/include/dt-bindings/power/imx8mn-power.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/*
+ *  Copyright (C) 2020 Compass Electronics Group, LLC
+ */
+
+#ifndef __DT_BINDINGS_IMX8MN_POWER_H__
+#define __DT_BINDINGS_IMX8MN_POWER_H__
+
+#define IMX8MN_POWER_DOMAIN_HSIOMIX	0
+#define IMX8MN_POWER_DOMAIN_OTG1	1
+#define IMX8MN_POWER_DOMAIN_GPUMIX	2
+#define IMX8MN_POWER_DOMAIN_DISPMIX	3
+#define IMX8MN_POWER_DOMAIN_MIPI	4
+
+#endif
-- 
2.30.2

[PATCH V2 08/24] imx: power-domain: Add fsl, imx8mm-gpc compatible string

[Marek Vasut]

The driver is compatible with iMX8MM, add missing compatible string.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/power/domain/imx8m-power-domain.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/power/domain/imx8m-power-domain.c b/drivers/power/domain/imx8m-power-domain.c
index c4cd07ffaf..ebac90d81c 100644
--- a/drivers/power/domain/imx8m-power-domain.c
+++ b/drivers/power/domain/imx8m-power-domain.c
@@ -120,6 +120,7 @@ static int imx8m_power_domain_of_to_plat(struct udevice *dev)
 
 static const struct udevice_id imx8m_power_domain_ids[] = {
 	{ .compatible = "fsl,imx8mq-gpc" },
+	{ .compatible = "fsl,imx8mm-gpc" },
 	{ }
 };
 
-- 
2.30.2

[PATCH V2 08/24] imx: power-domain: Add fsl, imx8mm-gpc compatible string

[Jaehoon Chung]

On 4/12/21 1:28 AM, Marek Vasut wrote:
> The driver is compatible with iMX8MM, add missing compatible string.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Ye Li <ye.li@nxp.com>
> Cc: uboot-imx <uboot-imx@nxp.com>

Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Best Regards,
Jaehoon chung

> ---
> V2: No change
> ---
>  drivers/power/domain/imx8m-power-domain.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/power/domain/imx8m-power-domain.c b/drivers/power/domain/imx8m-power-domain.c
> index c4cd07ffaf..ebac90d81c 100644
> --- a/drivers/power/domain/imx8m-power-domain.c
> +++ b/drivers/power/domain/imx8m-power-domain.c
> @@ -120,6 +120,7 @@ static int imx8m_power_domain_of_to_plat(struct udevice *dev)
>  
>  static const struct udevice_id imx8m_power_domain_ids[] = {
>  	{ .compatible = "fsl,imx8mq-gpc" },
> +	{ .compatible = "fsl,imx8mm-gpc" },
>  	{ }
>  };
>  
> 

[PATCH V2 09/24] imx: power-domain: Add fsl, imx8mn-gpc compatible string

[Marek Vasut]

The driver is compatible with iMX8MN, add missing compatible string.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: New patch
---
 drivers/power/domain/imx8m-power-domain.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/power/domain/imx8m-power-domain.c b/drivers/power/domain/imx8m-power-domain.c
index ebac90d81c..5d34bc1290 100644
--- a/drivers/power/domain/imx8m-power-domain.c
+++ b/drivers/power/domain/imx8m-power-domain.c
@@ -121,6 +121,7 @@ static int imx8m_power_domain_of_to_plat(struct udevice *dev)
 static const struct udevice_id imx8m_power_domain_ids[] = {
 	{ .compatible = "fsl,imx8mq-gpc" },
 	{ .compatible = "fsl,imx8mm-gpc" },
+	{ .compatible = "fsl,imx8mn-gpc" },
 	{ }
 };
 
-- 
2.30.2

[PATCH V2 09/24] imx: power-domain: Add fsl, imx8mn-gpc compatible string

[Jaehoon Chung]

On 4/12/21 1:28 AM, Marek Vasut wrote:
> The driver is compatible with iMX8MN, add missing compatible string.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Ye Li <ye.li@nxp.com>
> Cc: uboot-imx <uboot-imx@nxp.com>

Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Best Regards,
Jaehoon chung

> ---
> V2: New patch
> ---
>  drivers/power/domain/imx8m-power-domain.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/power/domain/imx8m-power-domain.c b/drivers/power/domain/imx8m-power-domain.c
> index ebac90d81c..5d34bc1290 100644
> --- a/drivers/power/domain/imx8m-power-domain.c
> +++ b/drivers/power/domain/imx8m-power-domain.c
> @@ -121,6 +121,7 @@ static int imx8m_power_domain_of_to_plat(struct udevice *dev)
>  static const struct udevice_id imx8m_power_domain_ids[] = {
>  	{ .compatible = "fsl,imx8mq-gpc" },
>  	{ .compatible = "fsl,imx8mm-gpc" },
> +	{ .compatible = "fsl,imx8mn-gpc" },
>  	{ }
>  };
>  
> 

[PATCH V2 10/24] usb: ehci-mx6: Turn off Vbus on probe failure

[Marek Vasut]

The driver turns on Vbus regulator in probe, but fails to turn it back
off in case of probe failure. Add the missing code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: Mark struct ehci_mx6_priv_data *priv as "__maybe_unused",
    because it gets used only if either DM_REGULATOR or later
    DM_CLK or PHY are enabled. So avoid a warning that priv is
    defined but not used.
---
 drivers/usb/host/ehci-mx6.c | 29 +++++++++++++++++++++++++++--
 1 file changed, 27 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index aeea539999..7b538b6dcb 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -640,7 +640,32 @@ static int ehci_usb_probe(struct udevice *dev)
 	hcor = (struct ehci_hcor *)((uint32_t)hccr +
 			HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
 
-	return ehci_register(dev, hccr, hcor, &mx6_ehci_ops, 0, priv->init_type);
+	ret = ehci_register(dev, hccr, hcor, &mx6_ehci_ops, 0, priv->init_type);
+	if (ret)
+		goto err_regulator;
+
+	return ret;
+
+err_regulator:
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	if (priv->vbus_supply)
+		regulator_set_enable(priv->vbus_supply, false);
+#endif
+	return ret;
+}
+
+int ehci_usb_remove(struct udevice *dev)
+{
+	struct ehci_mx6_priv_data *priv __maybe_unused = dev_get_priv(dev);
+
+	ehci_deregister(dev);
+
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	if (priv->vbus_supply)
+		regulator_set_enable(priv->vbus_supply, false);
+#endif
+
+	return 0;
 }
 
 static const struct udevice_id mx6_usb_ids[] = {
@@ -655,7 +680,7 @@ U_BOOT_DRIVER(usb_mx6) = {
 	.of_to_plat = ehci_usb_of_to_plat,
 	.bind	= ehci_usb_bind,
 	.probe	= ehci_usb_probe,
-	.remove = ehci_deregister,
+	.remove = ehci_usb_remove,
 	.ops	= &ehci_usb_ops,
 	.plat_auto	= sizeof(struct usb_plat),
 	.priv_auto	= sizeof(struct ehci_mx6_priv_data),
-- 
2.30.2

[PATCH V2 11/24] usb: ehci-mx6: Add DM clock support

[Marek Vasut]

Add support for using DM clock framework to enable and disable all the
necessary clock for the USB controller.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/usb/host/ehci-mx6.c | 37 ++++++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 7b538b6dcb..04b072e717 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -5,6 +5,7 @@
  */
 
 #include <common.h>
+#include <clk.h>
 #include <log.h>
 #include <usb.h>
 #include <errno.h>
@@ -347,9 +348,6 @@ int ehci_mx6_common_init(struct usb_ehci *ehci, int index)
 {
 	int ret;
 
-	enable_usboh3_clk(1);
-	mdelay(1);
-
 	/* Do board specific initialization */
 	ret = board_ehci_hcd_init(index);
 	if (ret)
@@ -391,6 +389,9 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 		}
 	}
 
+	enable_usboh3_clk(1);
+	mdelay(1);
+
 	ret = ehci_mx6_common_init(ehci, index);
 	if (ret)
 		return ret;
@@ -428,6 +429,7 @@ struct ehci_mx6_priv_data {
 	struct ehci_ctrl ctrl;
 	struct usb_ehci *ehci;
 	struct udevice *vbus_supply;
+	struct clk clk;
 	enum usb_init_type init_type;
 	int portnr;
 };
@@ -606,6 +608,20 @@ static int ehci_usb_probe(struct udevice *dev)
 	priv->portnr = dev_seq(dev);
 	priv->init_type = type;
 
+#if CONFIG_IS_ENABLED(CLK)
+	ret = clk_get_by_index(dev, 0, &priv->clk);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_enable(&priv->clk);
+	if (ret)
+		return ret;
+#else
+	/* Compatibility with DM_USB and !CLK */
+	enable_usboh3_clk(1);
+	mdelay(1);
+#endif
+
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	ret = device_get_supply_regulator(dev, "vbus-supply",
 					  &priv->vbus_supply);
@@ -614,7 +630,7 @@ static int ehci_usb_probe(struct udevice *dev)
 #endif
 	ret = ehci_mx6_common_init(ehci, priv->portnr);
 	if (ret)
-		return ret;
+		goto err_clk;
 
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	if (priv->vbus_supply) {
@@ -623,7 +639,7 @@ static int ehci_usb_probe(struct udevice *dev)
 					   false : true);
 		if (ret && ret != -ENOSYS) {
 			printf("Error enabling VBUS supply (ret=%i)\n", ret);
-			return ret;
+			goto err_clk;
 		}
 	}
 #endif
@@ -650,6 +666,13 @@ err_regulator:
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	if (priv->vbus_supply)
 		regulator_set_enable(priv->vbus_supply, false);
+#endif
+err_clk:
+#if CONFIG_IS_ENABLED(CLK)
+	clk_disable(&priv->clk);
+#else
+	/* Compatibility with DM_USB and !CLK */
+	enable_usboh3_clk(0);
 #endif
 	return ret;
 }
@@ -665,6 +688,10 @@ int ehci_usb_remove(struct udevice *dev)
 		regulator_set_enable(priv->vbus_supply, false);
 #endif
 
+#if CONFIG_IS_ENABLED(CLK)
+	clk_disable(&priv->clk);
+#endif
+
 	return 0;
 }
 
-- 
2.30.2

[PATCH V2 12/24] usb: ehci-mx6: Unify USBNC registers

[Marek Vasut]

Merge USBNC register layout structure into a single one, instead of
having three separate structures and a lot of ifdeffery. No functional
change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/usb/host/ehci-mx6.c | 53 +++++++++++++------------------------
 1 file changed, 19 insertions(+), 34 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 04b072e717..915b25a618 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -68,6 +68,24 @@ DECLARE_GLOBAL_DATA_PTR;
 #define UCMD_RUN_STOP           (1 << 0) /* controller run/stop */
 #define UCMD_RESET		(1 << 1) /* controller reset */
 
+/* Base address for this IP block is 0x02184800 */
+struct usbnc_regs {
+	u32 ctrl[4]; /* otg/host1-3 */
+	u32 uh2_hsic_ctrl;
+	u32 uh3_hsic_ctrl;
+	u32 otg_phy_ctrl_0;
+	u32 uh1_phy_ctrl_0;
+	u32 reserve1[4];
+	u32 phy_cfg1;
+	u32 phy_cfg2;
+	u32 reserve2;
+	u32 phy_status;
+	u32 reserve3[4];
+	u32 adp_cfg1;
+	u32 adp_cfg2;
+	u32 adp_status;
+};
+
 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
 static const unsigned phy_bases[] = {
 	USB_PHY0_BASE_ADDR,
@@ -207,39 +225,7 @@ int usb_phy_mode(int port)
 		return USB_INIT_HOST;
 }
 
-#if defined(CONFIG_MX7ULP)
-struct usbnc_regs {
-	u32 ctrl1;
-	u32 ctrl2;
-	u32 reserve0[2];
-	u32 hsic_ctrl;
-};
-#else
-/* Base address for this IP block is 0x02184800 */
-struct usbnc_regs {
-	u32	ctrl[4];	/* otg/host1-3 */
-	u32	uh2_hsic_ctrl;
-	u32	uh3_hsic_ctrl;
-	u32	otg_phy_ctrl_0;
-	u32	uh1_phy_ctrl_0;
-};
-#endif
-
 #elif defined(CONFIG_MX7)
-struct usbnc_regs {
-	u32 ctrl1;
-	u32 ctrl2;
-	u32 reserve1[10];
-	u32 phy_cfg1;
-	u32 phy_cfg2;
-	u32 reserve2;
-	u32 phy_status;
-	u32 reserve3[4];
-	u32 adp_cfg1;
-	u32 adp_cfg2;
-	u32 adp_status;
-};
-
 static void usb_power_config(int index)
 {
 	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
@@ -274,12 +260,11 @@ static void usb_oc_config(int index)
 #if defined(CONFIG_MX6)
 	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
 			USB_OTHERREGS_OFFSET);
-	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
 #elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP)
 	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
 			(0x10000 * index) + USBNC_OFFSET);
-	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);
 #endif
+	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
 
 #if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
 	/* mx6qarm2 seems to required a different setting*/
-- 
2.30.2

[PATCH V2 13/24] usb: ehci-mx6: Parse USB PHY and MISC offsets from DT

[Marek Vasut]

In case DM and OF controler is enabled, but PHY support is disabled,
parse USB PHY and MISC component addresses from DT manually. Those
component addresses will be used in subsequent patches to access the
ANATOP, PHY and MISC registers matching the controller and thus get
rid of the ad-hoc controller sequence number mapping.

Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: - Move anatop_off variable inside if defined(CONFIG_MX6) to avoid
      warning, that the variable is defined and not used on !MX6
    - Parse PHY and USBMISC addresses unconditionally, with or without
      CONFIG_PHY enabled or disabled
---
 drivers/usb/host/ehci-mx6.c | 55 +++++++++++++++++++++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 915b25a618..164054eaf8 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -417,6 +417,9 @@ struct ehci_mx6_priv_data {
 	struct clk clk;
 	enum usb_init_type init_type;
 	int portnr;
+	void __iomem *phy_addr;
+	void __iomem *misc_addr;
+	void __iomem *anatop_addr;
 };
 
 static int mx6_init_after_reset(struct ehci_ctrl *dev)
@@ -571,6 +574,54 @@ static int ehci_usb_bind(struct udevice *dev)
 	return 0;
 }
 
+static int mx6_parse_dt_addrs(struct udevice *dev)
+{
+	struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
+	int phy_off, misc_off;
+	const void *blob = gd->fdt_blob;
+	int offset = dev_of_offset(dev);
+	void *__iomem addr;
+
+	phy_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbphy");
+	if (phy_off < 0) {
+		phy_off = fdtdec_lookup_phandle(blob, offset, "phys");
+		if (phy_off < 0)
+			return -EINVAL;
+	}
+
+	misc_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbmisc");
+	if (misc_off < 0)
+		return -EINVAL;
+
+	addr = (void __iomem *)fdtdec_get_addr(blob, phy_off, "reg");
+	if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	priv->phy_addr = addr;
+
+	addr = (void __iomem *)fdtdec_get_addr(blob, misc_off, "reg");
+	if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	priv->misc_addr = addr;
+
+#if !defined(CONFIG_PHY) && defined(CONFIG_MX6)
+	int anatop_off;
+
+	/* Resolve ANATOP offset through USB PHY node */
+	anatop_off = fdtdec_lookup_phandle(blob, phy_off, "fsl,anatop");
+	if (anatop_off < 0)
+		return -EINVAL;
+
+	addr = (void __iomem *)fdtdec_get_addr(blob, anatop_off, "reg");
+	if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	priv->anatop_addr = addr;
+#endif
+	return 0;
+}
+
 static int ehci_usb_probe(struct udevice *dev)
 {
 	struct usb_plat *plat = dev_get_plat(dev);
@@ -589,6 +640,10 @@ static int ehci_usb_probe(struct udevice *dev)
 		}
 	}
 
+	ret = mx6_parse_dt_addrs(dev);
+	if (ret)
+		return ret;
+
 	priv->ehci = ehci;
 	priv->portnr = dev_seq(dev);
 	priv->init_type = type;
-- 
2.30.2

[PATCH V2 14/24] usb: ehci-mx6: Split ehci_mx6_common_init()

[Marek Vasut]

In order to pass component addresses around easily instead of passing
ad-hoc sequence numbers, it is necessary to split ehci_mx6_common_init().
Make it so and call the separate functions instead.

Since board_ehci_hcd_init() makes no sense in DM case, do not call it
in DM case.

Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: Declare ret only if CONFIG_IS_ENABLED(DM_REGULATOR) , to avoid
    warning that it is declared, but not used
---
 drivers/usb/host/ehci-mx6.c | 60 ++++++++++++++++++-------------------
 1 file changed, 30 insertions(+), 30 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 164054eaf8..19c010b5ad 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -283,6 +283,7 @@ static void usb_oc_config(int index)
 #endif
 }
 
+#if !CONFIG_IS_ENABLED(DM_USB)
 /**
  * board_usb_phy_mode - override usb phy mode
  * @port:	usb host/otg port
@@ -329,27 +330,6 @@ int __weak board_ehci_power(int port, int on)
 	return 0;
 }
 
-int ehci_mx6_common_init(struct usb_ehci *ehci, int index)
-{
-	int ret;
-
-	/* Do board specific initialization */
-	ret = board_ehci_hcd_init(index);
-	if (ret)
-		return ret;
-
-	usb_power_config(index);
-	usb_oc_config(index);
-
-#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
-	usb_internal_phy_clock_gate(index, 1);
-	usb_phy_enable(index, ehci);
-#endif
-
-	return 0;
-}
-
-#if !CONFIG_IS_ENABLED(DM_USB)
 int ehci_hcd_init(int index, enum usb_init_type init,
 		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
 {
@@ -377,9 +357,20 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	enable_usboh3_clk(1);
 	mdelay(1);
 
-	ret = ehci_mx6_common_init(ehci, index);
-	if (ret)
+	/* Do board specific initialization */
+	ret = board_ehci_hcd_init(index);
+	if (ret) {
+		enable_usboh3_clk(0);
 		return ret;
+	}
+
+	usb_power_config(index);
+	usb_oc_config(index);
+
+#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
+	usb_internal_phy_clock_gate(index, 1);
+	usb_phy_enable(index, ehci);
+#endif
 
 	type = board_usb_phy_mode(index);
 
@@ -427,14 +418,18 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev)
 	struct ehci_mx6_priv_data *priv = dev->priv;
 	enum usb_init_type type = priv->init_type;
 	struct usb_ehci *ehci = priv->ehci;
-	int ret;
 
-	ret = ehci_mx6_common_init(priv->ehci, priv->portnr);
-	if (ret)
-		return ret;
+	usb_power_config(priv->portnr);
+	usb_oc_config(priv->portnr);
+
+#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
+	usb_internal_phy_clock_gate(priv->portnr, 1);
+	usb_phy_enable(priv->portnr, ehci);
+#endif
 
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	if (priv->vbus_supply) {
+		int ret;
 		ret = regulator_set_enable(priv->vbus_supply,
 					   (type == USB_INIT_DEVICE) ?
 					   false : true);
@@ -668,9 +663,14 @@ static int ehci_usb_probe(struct udevice *dev)
 	if (ret)
 		debug("%s: No vbus supply\n", dev->name);
 #endif
-	ret = ehci_mx6_common_init(ehci, priv->portnr);
-	if (ret)
-		goto err_clk;
+
+	usb_power_config(priv->portnr);
+	usb_oc_config(priv->portnr);
+
+#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
+	usb_internal_phy_clock_gate(priv->portnr, 1);
+	usb_phy_enable(priv->portnr, ehci);
+#endif
 
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	if (priv->vbus_supply) {
-- 
2.30.2

[PATCH V2 15/24] usb: ehci-mx6: Pass PHY address to usb_*_phy*()

[Marek Vasut]

Instead of passing ad-hoc index to USB PHY handling functions and then
try and figure out the PHY address, pass in the PHY address itself. For
DM case, this address comes easily from DT. For non-DM case, the previous
method is still present, however the non-DM case will soon be removed.

Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/usb/host/ehci-mx6.c | 29 ++++++++++-------------------
 1 file changed, 10 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 19c010b5ad..b43c55765c 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -94,14 +94,8 @@ static const unsigned phy_bases[] = {
 #endif
 };
 
-static void usb_internal_phy_clock_gate(int index, int on)
+static void usb_internal_phy_clock_gate(void __iomem *phy_reg, int on)
 {
-	void __iomem *phy_reg;
-
-	if (index >= ARRAY_SIZE(phy_bases))
-		return;
-
-	phy_reg = (void __iomem *)phy_bases[index];
 	phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
 	writel(USBPHY_CTRL_CLKGATE, phy_reg);
 }
@@ -166,17 +160,12 @@ static void usb_power_config(int index)
 }
 
 /* Return 0 : host node, <>0 : device mode */
-static int usb_phy_enable(int index, struct usb_ehci *ehci)
+static int usb_phy_enable(struct usb_ehci *ehci, void __iomem *phy_reg)
 {
-	void __iomem *phy_reg;
 	void __iomem *phy_ctrl;
 	void __iomem *usb_cmd;
 	int ret;
 
-	if (index >= ARRAY_SIZE(phy_bases))
-		return 0;
-
-	phy_reg = (void __iomem *)phy_bases[index];
 	phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
 	usb_cmd = (void __iomem *)&ehci->usbcmd;
 
@@ -368,8 +357,10 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	usb_oc_config(index);
 
 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
-	usb_internal_phy_clock_gate(index, 1);
-	usb_phy_enable(index, ehci);
+	if (index < ARRAY_SIZE(phy_bases)) {
+		usb_internal_phy_clock_gate((void __iomem *)phy_bases[index], 1);
+		usb_phy_enable(ehci, (void __iomem *)phy_bases[index]);
+	}
 #endif
 
 	type = board_usb_phy_mode(index);
@@ -423,8 +414,8 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev)
 	usb_oc_config(priv->portnr);
 
 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
-	usb_internal_phy_clock_gate(priv->portnr, 1);
-	usb_phy_enable(priv->portnr, ehci);
+	usb_internal_phy_clock_gate(priv->phy_addr, 1);
+	usb_phy_enable(ehci, priv->phy_addr);
 #endif
 
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
@@ -668,8 +659,8 @@ static int ehci_usb_probe(struct udevice *dev)
 	usb_oc_config(priv->portnr);
 
 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
-	usb_internal_phy_clock_gate(priv->portnr, 1);
-	usb_phy_enable(priv->portnr, ehci);
+	usb_internal_phy_clock_gate(priv->phy_addr, 1);
+	usb_phy_enable(ehci, priv->phy_addr);
 #endif
 
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
-- 
2.30.2

[PATCH V2 16/24] usb: ehci-mx6: Split usb_power_config()

[Marek Vasut]

Split usb_power_config() per SoC and pass in USB PHY, USBNC and ANATOP
addresses instead of ad-hoc sequence numbers. This is only applicable
on legacy systems which do not implement proper PHY support. Once PHY
support is available, parts of this can be removed altogether and moved
to the PHY driver, similar to Linux phy-mxs-usb.c .

Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: - Always call usb_oc_config(), independent of whether CONFIG_PHY is
      or is not enabled
    - Only call usb_internal_phy_clock_gate() and usb_phy_enable()
      if CONFIG_PHY is disabled
    - Always define usb_power_config_*() and mark the empty
      implementations with __maybe_unused, since this vastly
      simplifies the ifdeffery and makes it much clearer what
      the intention of the ifdefs is
---
 drivers/usb/host/ehci-mx6.c | 143 +++++++++++++++++++++++-------------
 1 file changed, 92 insertions(+), 51 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index b43c55765c..d022df04ab 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -86,43 +86,18 @@ struct usbnc_regs {
 	u32 adp_status;
 };
 
-#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
-static const unsigned phy_bases[] = {
-	USB_PHY0_BASE_ADDR,
-#if defined(USB_PHY1_BASE_ADDR)
-	USB_PHY1_BASE_ADDR,
-#endif
-};
-
-static void usb_internal_phy_clock_gate(void __iomem *phy_reg, int on)
+#if defined(CONFIG_MX6) && !defined(CONFIG_PHY)
+static void usb_power_config_mx6(struct anatop_regs __iomem *anatop,
+				 int anatop_bits_index)
 {
-	phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
-	writel(USBPHY_CTRL_CLKGATE, phy_reg);
-}
-
-static void usb_power_config(int index)
-{
-#if defined(CONFIG_MX7ULP)
-	struct usbphy_regs __iomem *usbphy =
-		(struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR;
-
-	if (index > 0)
-		return;
-
-	writel(ANADIG_USB2_CHRG_DETECT_EN_B |
-		   ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
-		   &usbphy->usb1_chrg_detect);
-
-	scg_enable_usb_pll(true);
-
-#else
-	struct anatop_regs __iomem *anatop =
-		(struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
 	void __iomem *chrg_detect;
 	void __iomem *pll_480_ctrl_clr;
 	void __iomem *pll_480_ctrl_set;
 
-	switch (index) {
+	if (!is_mx6())
+		return;
+
+	switch (anatop_bits_index) {
 	case 0:
 		chrg_detect = &anatop->usb1_chrg_detect;
 		pll_480_ctrl_clr = &anatop->usb1_pll_480_ctrl_clr;
@@ -155,8 +130,61 @@ static void usb_power_config(int index)
 		     ANADIG_USB2_PLL_480_CTRL_POWER |
 		     ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
 		     pll_480_ctrl_set);
+}
+#else
+static void __maybe_unused
+usb_power_config_mx6(void *anatop, int anatop_bits_index) { }
+#endif
 
+#if defined(CONFIG_MX7) && !defined(CONFIG_PHY)
+static void usb_power_config_mx7(struct usbnc_regs *usbnc)
+{
+	void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2);
+
+	if (!is_mx7())
+		return;
+
+	/*
+	 * Clear the ACAENB to enable usb_otg_id detection,
+	 * otherwise it is the ACA detection enabled.
+	 */
+	clrbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB);
+}
+#else
+static void __maybe_unused
+usb_power_config_mx7(void *usbnc) { }
 #endif
+
+#if defined(CONFIG_MX7ULP) && !defined(CONFIG_PHY)
+static void usb_power_config_mx7ulp(struct usbphy_regs __iomem *usbphy)
+{
+	if (!is_mx7ulp())
+		return;
+
+	writel(ANADIG_USB2_CHRG_DETECT_EN_B |
+	       ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
+	       &usbphy->usb1_chrg_detect);
+
+	scg_enable_usb_pll(true);
+}
+#else
+static void __maybe_unused
+usb_power_config_mx7ulp(void *usbphy) { }
+#endif
+
+#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
+static const unsigned phy_bases[] = {
+	USB_PHY0_BASE_ADDR,
+#if defined(USB_PHY1_BASE_ADDR)
+	USB_PHY1_BASE_ADDR,
+#endif
+};
+
+#if !defined(CONFIG_PHY)
+static void usb_internal_phy_clock_gate(void __iomem *phy_reg, int on)
+{
+	phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
+	writel(USBPHY_CTRL_CLKGATE, phy_reg);
 }
 
 /* Return 0 : host node, <>0 : device mode */
@@ -196,6 +224,7 @@ static int usb_phy_enable(struct usb_ehci *ehci, void __iomem *phy_reg)
 
 	return 0;
 }
+#endif
 
 int usb_phy_mode(int port)
 {
@@ -215,19 +244,6 @@ int usb_phy_mode(int port)
 }
 
 #elif defined(CONFIG_MX7)
-static void usb_power_config(int index)
-{
-	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
-			(0x10000 * index) + USBNC_OFFSET);
-	void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2);
-
-	/*
-	 * Clear the ACAENB to enable usb_otg_id detection,
-	 * otherwise it is the ACA detection enabled.
-	 */
-	clrbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB);
-}
-
 int usb_phy_mode(int port)
 {
 	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
@@ -325,8 +341,16 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	enum usb_init_type type;
 #if defined(CONFIG_MX6)
 	u32 controller_spacing = 0x200;
-#elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP)
+	struct anatop_regs __iomem *anatop =
+		(struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
+#elif defined(CONFIG_MX7)
+	u32 controller_spacing = 0x10000;
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			(0x10000 * index) + USBNC_OFFSET);
+#elif defined(CONFIG_MX7ULP)
 	u32 controller_spacing = 0x10000;
+	struct usbphy_regs __iomem *usbphy =
+		(struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR;
 #endif
 	struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
 		(controller_spacing * index));
@@ -353,7 +377,14 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 		return ret;
 	}
 
-	usb_power_config(index);
+#if defined(CONFIG_MX6)
+	usb_power_config_mx6(anatop, index);
+#elif defined (CONFIG_MX7)
+	usb_power_config_mx7(usbnc);
+#elif defined (CONFIG_MX7ULP)
+	usb_power_config_mx7ulp(usbphy);
+#endif
+
 	usb_oc_config(index);
 
 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
@@ -410,10 +441,15 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev)
 	enum usb_init_type type = priv->init_type;
 	struct usb_ehci *ehci = priv->ehci;
 
-	usb_power_config(priv->portnr);
+#if !defined(CONFIG_PHY)
+	usb_power_config_mx6(priv->anatop_addr, priv->portnr);
+	usb_power_config_mx7(priv->misc_addr);
+	usb_power_config_mx7ulp(priv->phy_addr);
+#endif
+
 	usb_oc_config(priv->portnr);
 
-#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
+#if !defined(CONFIG_PHY) && (defined(CONFIG_MX6) || defined(CONFIG_MX7ULP))
 	usb_internal_phy_clock_gate(priv->phy_addr, 1);
 	usb_phy_enable(ehci, priv->phy_addr);
 #endif
@@ -655,10 +691,15 @@ static int ehci_usb_probe(struct udevice *dev)
 		debug("%s: No vbus supply\n", dev->name);
 #endif
 
-	usb_power_config(priv->portnr);
+#if !defined(CONFIG_PHY)
+	usb_power_config_mx6(priv->anatop_addr, priv->portnr);
+	usb_power_config_mx7(priv->misc_addr);
+	usb_power_config_mx7ulp(priv->phy_addr);
+#endif
+
 	usb_oc_config(priv->portnr);
 
-#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
+#if !defined(CONFIG_PHY) && (defined(CONFIG_MX6) || defined(CONFIG_MX7ULP))
 	usb_internal_phy_clock_gate(priv->phy_addr, 1);
 	usb_phy_enable(ehci, priv->phy_addr);
 #endif
-- 
2.30.2

[PATCH V2 17/24] usb: ehci-mx6: Pass MISC address to usb_oc_config()

[Marek Vasut]

Instead of passing ad-hoc sequence number to usb_oc_config(), pass in
the USB MISC address itself. The USB MISC address comes from DT in DM
case, and from the old method using controller index in non-DM case.

Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/usb/host/ehci-mx6.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index d022df04ab..99fd0e7183 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -260,15 +260,8 @@ int usb_phy_mode(int port)
 }
 #endif
 
-static void usb_oc_config(int index)
+static void usb_oc_config(struct usbnc_regs *usbnc, int index)
 {
-#if defined(CONFIG_MX6)
-	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
-			USB_OTHERREGS_OFFSET);
-#elif defined(CONFIG_MX7) || defined(CONFIG_MX7ULP)
-	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
-			(0x10000 * index) + USBNC_OFFSET);
-#endif
 	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
 
 #if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
@@ -343,6 +336,8 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	u32 controller_spacing = 0x200;
 	struct anatop_regs __iomem *anatop =
 		(struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			USB_OTHERREGS_OFFSET);
 #elif defined(CONFIG_MX7)
 	u32 controller_spacing = 0x10000;
 	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
@@ -351,6 +346,8 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	u32 controller_spacing = 0x10000;
 	struct usbphy_regs __iomem *usbphy =
 		(struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR;
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			(0x10000 * index) + USBNC_OFFSET);
 #endif
 	struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
 		(controller_spacing * index));
@@ -385,7 +382,7 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	usb_power_config_mx7ulp(usbphy);
 #endif
 
-	usb_oc_config(index);
+	usb_oc_config(usbnc, index);
 
 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
 	if (index < ARRAY_SIZE(phy_bases)) {
@@ -447,7 +444,7 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev)
 	usb_power_config_mx7ulp(priv->phy_addr);
 #endif
 
-	usb_oc_config(priv->portnr);
+	usb_oc_config(priv->misc_addr, priv->portnr);
 
 #if !defined(CONFIG_PHY) && (defined(CONFIG_MX6) || defined(CONFIG_MX7ULP))
 	usb_internal_phy_clock_gate(priv->phy_addr, 1);
@@ -697,7 +694,7 @@ static int ehci_usb_probe(struct udevice *dev)
 	usb_power_config_mx7ulp(priv->phy_addr);
 #endif
 
-	usb_oc_config(priv->portnr);
+	usb_oc_config(priv->misc_addr, priv->portnr);
 
 #if !defined(CONFIG_PHY) && (defined(CONFIG_MX6) || defined(CONFIG_MX7ULP))
 	usb_internal_phy_clock_gate(priv->phy_addr, 1);
-- 
2.30.2

[PATCH V2 18/24] usb: ehci-mx6: Use portnr from DT in DM case

[Marek Vasut]

In case the platform uses DM, determine port number, which is
used as offset in USBMISC registers, from PHY node DT aliases,
just like Linux does.

Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: Mostly new patch, since the old one no longer makes sense
---
 drivers/usb/host/ehci-mx6.c | 52 +++++--------------------------------
 1 file changed, 7 insertions(+), 45 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 99fd0e7183..68f6ecc872 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -550,49 +550,6 @@ static int ehci_usb_of_to_plat(struct udevice *dev)
 	return 0;
 }
 
-static int ehci_usb_bind(struct udevice *dev)
-{
-	/*
-	 * TODO:
-	 * This driver is only partly converted to DT probing and still uses
-	 * a tremendous amount of hard-coded addresses. To make things worse,
-	 * the driver depends on specific sequential indexing of controllers,
-	 * from which it derives offsets in the PHY and ANATOP register sets.
-	 *
-	 * Here we attempt to calculate these indexes from DT information as
-	 * well as we can. The USB controllers on all existing iMX6 SoCs
-	 * are placed next to each other, at addresses incremented by 0x200,
-	 * and iMX7 their addresses are shifted by 0x10000.
-	 * Thus, the index is derived from the multiple of 0x200 (0x10000 for
-	 * iMX7) offset from the first controller address.
-	 *
-	 * However, to complete conversion of this driver to DT probing, the
-	 * following has to be done:
-	 * - DM clock framework support for iMX must be implemented
-	 * - usb_power_config() has to be converted to clock framework
-	 *   -> Thus, the ad-hoc "index" variable goes away.
-	 * - USB PHY handling has to be factored out into separate driver
-	 *   -> Thus, the ad-hoc "index" variable goes away from the PHY
-	 *      code, the PHY driver must parse it's address from DT. This
-	 *      USB driver must find the PHY driver via DT phandle.
-	 *   -> usb_power_config() shall be moved to PHY driver
-	 * With these changes in place, the ad-hoc indexing goes away and
-	 * the driver is fully converted to DT probing.
-	 */
-
-	/*
-	 * FIXME: This cannot work with the new sequence numbers.
-	 * Please complete the DM conversion.
-	 *
-	 * u32 controller_spacing = is_mx7() ? 0x10000 : 0x200;
-	 * fdt_addr_t addr = devfdt_get_addr_index(dev, 0);
-	 *
-	 * dev->req_seq = (addr - USB_BASE_ADDR) / controller_spacing;
-	 */
-
-	return 0;
-}
-
 static int mx6_parse_dt_addrs(struct udevice *dev)
 {
 	struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
@@ -600,6 +557,7 @@ static int mx6_parse_dt_addrs(struct udevice *dev)
 	const void *blob = gd->fdt_blob;
 	int offset = dev_of_offset(dev);
 	void *__iomem addr;
+	int ret, devnump;
 
 	phy_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbphy");
 	if (phy_off < 0) {
@@ -608,6 +566,11 @@ static int mx6_parse_dt_addrs(struct udevice *dev)
 			return -EINVAL;
 	}
 
+	ret = fdtdec_get_alias_seq(blob, dev->uclass->uc_drv->name,
+				   phy_off, &devnump);
+	if (ret < 0)
+		return ret;
+
 	misc_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbmisc");
 	if (misc_off < 0)
 		return -EINVAL;
@@ -617,6 +580,7 @@ static int mx6_parse_dt_addrs(struct udevice *dev)
 		return -EINVAL;
 
 	priv->phy_addr = addr;
+	priv->portnr = devnump;
 
 	addr = (void __iomem *)fdtdec_get_addr(blob, misc_off, "reg");
 	if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
@@ -664,7 +628,6 @@ static int ehci_usb_probe(struct udevice *dev)
 		return ret;
 
 	priv->ehci = ehci;
-	priv->portnr = dev_seq(dev);
 	priv->init_type = type;
 
 #if CONFIG_IS_ENABLED(CLK)
@@ -774,7 +737,6 @@ U_BOOT_DRIVER(usb_mx6) = {
 	.id	= UCLASS_USB,
 	.of_match = mx6_usb_ids,
 	.of_to_plat = ehci_usb_of_to_plat,
-	.bind	= ehci_usb_bind,
 	.probe	= ehci_usb_probe,
 	.remove = ehci_usb_remove,
 	.ops	= &ehci_usb_ops,
-- 
2.30.2

[PATCH V2 19/24] usb: ehci-mx6: Add generic EHCI PHY support

[Marek Vasut]

In case PHY support is enabled, use the generic EHCI PHY support
to start and stop the PHY.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: Shift ifdefs around error handling goto labels to avoid warnings
    that the labels are defined but not used
---
 drivers/usb/host/ehci-mx6.c | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 68f6ecc872..8e20941855 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -425,6 +425,7 @@ struct ehci_mx6_priv_data {
 	struct usb_ehci *ehci;
 	struct udevice *vbus_supply;
 	struct clk clk;
+	struct phy phy;
 	enum usb_init_type init_type;
 	int portnr;
 	void __iomem *phy_addr;
@@ -684,22 +685,32 @@ static int ehci_usb_probe(struct udevice *dev)
 
 	mdelay(10);
 
+#if defined(CONFIG_PHY)
+	ret = ehci_setup_phy(dev, &priv->phy, 0);
+	if (ret)
+		goto err_regulator;
+#endif
+
 	hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
 	hcor = (struct ehci_hcor *)((uint32_t)hccr +
 			HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
 
 	ret = ehci_register(dev, hccr, hcor, &mx6_ehci_ops, 0, priv->init_type);
 	if (ret)
-		goto err_regulator;
+		goto err_phy;
 
 	return ret;
 
+err_phy:
+#if defined(CONFIG_PHY)
+	ehci_shutdown_phy(dev, &priv->phy);
 err_regulator:
+#endif
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	if (priv->vbus_supply)
 		regulator_set_enable(priv->vbus_supply, false);
-#endif
 err_clk:
+#endif
 #if CONFIG_IS_ENABLED(CLK)
 	clk_disable(&priv->clk);
 #else
@@ -715,6 +726,10 @@ int ehci_usb_remove(struct udevice *dev)
 
 	ehci_deregister(dev);
 
+#if defined(CONFIG_PHY)
+	ehci_shutdown_phy(dev, &priv->phy);
+#endif
+
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
 	if (priv->vbus_supply)
 		regulator_set_enable(priv->vbus_supply, false);
-- 
2.30.2

[PATCH V2 20/24] usb: ehci-mx6: Set default CONFIG_MXC_USB_PORTSC if not defined

[Marek Vasut]

There is now multiple copies of CONFIG_MXC_USB_PORTSC in configs set to
PORT_PTS_UTMI | PORT_PTS_PTW, which is in fact the default register value
for MX6, MX7 and MX7ULP. Define the default value of CONFIG_MXC_USB_PORTSC
in the driver and use it in case CONFIG_MXC_USB_PORTSC is not defined in
config, to reduce the duplication.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: New patch
---
 drivers/usb/host/ehci-mx6.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 8e20941855..d3308c60ee 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -68,6 +68,11 @@ DECLARE_GLOBAL_DATA_PTR;
 #define UCMD_RUN_STOP           (1 << 0) /* controller run/stop */
 #define UCMD_RESET		(1 << 1) /* controller reset */
 
+/* If this is not defined, assume MX6/MX7/MX8M SoC default */
+#ifndef CONFIG_MXC_USB_PORTSC
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#endif
+
 /* Base address for this IP block is 0x02184800 */
 struct usbnc_regs {
 	u32 ctrl[4]; /* otg/host1-3 */
-- 
2.30.2

[PATCH V2 21/24] usb: ehci-mx6: Add fsl,imx7d-usb compatible string

[Marek Vasut]

Add new compatible string, used by some more up-to-date DTs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: No change
---
 drivers/usb/host/ehci-mx6.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index d3308c60ee..28db593b7e 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -749,6 +749,7 @@ int ehci_usb_remove(struct udevice *dev)
 
 static const struct udevice_id mx6_usb_ids[] = {
 	{ .compatible = "fsl,imx27-usb" },
+	{ .compatible = "fsl,imx7d-usb" },
 	{ }
 };
 
-- 
2.30.2

[PATCH V2 22/24] usb: ehci-mx6: Fix aarch64 build warnings

[Marek Vasut]

Fix cast from pointer to integer of different size by casting the
pointer to uintptr_t instead of uint32_t, the former has correct
size on both 32bit and 64bit architectures.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: New patch
---
 drivers/usb/host/ehci-mx6.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 28db593b7e..7642a31b65 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -399,8 +399,8 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 	type = board_usb_phy_mode(index);
 
 	if (hccr && hcor) {
-		*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
-		*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
+		*hccr = (struct ehci_hccr *)((uintptr_t)&ehci->caplength);
+		*hcor = (struct ehci_hcor *)((uintptr_t)*hccr +
 				HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
 	}
 
@@ -696,8 +696,8 @@ static int ehci_usb_probe(struct udevice *dev)
 		goto err_regulator;
 #endif
 
-	hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
-	hcor = (struct ehci_hcor *)((uint32_t)hccr +
+	hccr = (struct ehci_hccr *)((uintptr_t)&ehci->caplength);
+	hcor = (struct ehci_hcor *)((uintptr_t)hccr +
 			HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
 
 	ret = ehci_register(dev, hccr, hcor, &mx6_ehci_ops, 0, priv->init_type);
-- 
2.30.2

[PATCH V2 23/24] usb: ehci-mx6: Add iMX8M support

[Marek Vasut]

The iMX8M uses nop PHY, select PHY and NOP_PHY automatically.
Otherwise, the DM capable driver is now perfectly compatible.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---
V2: Permit the driver on all iMX8M SoCs, not just iMX8MM
---
 drivers/usb/host/Kconfig | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 0971a7c813..bf5d82f035 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -156,7 +156,9 @@ config USB_EHCI_MX6
 
 config USB_EHCI_MX7
 	bool "Support for i.MX7 on-chip EHCI USB controller"
-	depends on ARCH_MX7
+	depends on ARCH_MX7 || IMX8M
+	select PHY if IMX8M
+	select NOP_PHY if IMX8M
 	default y
 	---help---
 	  Enables support for the on-chip EHCI controller on i.MX7 SoCs.
-- 
2.30.2

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Marek Vasut]

Enable USB host support on MX8MM Verdin.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---
V2: No change
---
 configs/verdin-imx8mm_defconfig | 8 +++++++-
 include/configs/verdin-imx8mm.h | 5 +++++
 2 files changed, 12 insertions(+), 1 deletion(-)

diff --git a/configs/verdin-imx8mm_defconfig b/configs/verdin-imx8mm_defconfig
index ea0b5978f1..c8c3420b6a 100644
--- a/configs/verdin-imx8mm_defconfig
+++ b/configs/verdin-imx8mm_defconfig
@@ -37,7 +37,6 @@ CONFIG_SPL_BOARD_INIT=y
 CONFIG_SPL_SEPARATE_BSS=y
 CONFIG_SPL_I2C_SUPPORT=y
 CONFIG_SPL_POWER_SUPPORT=y
-CONFIG_SPL_USB_HOST_SUPPORT=y
 CONFIG_SPL_WATCHDOG_SUPPORT=y
 CONFIG_SYS_PROMPT="Verdin iMX8MM # "
 # CONFIG_BOOTM_NETBSD is not set
@@ -50,6 +49,7 @@ CONFIG_CMD_FUSE=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_UUID=y
 CONFIG_CMD_REGULATOR=y
@@ -89,6 +89,8 @@ CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
 CONFIG_SPL_DM_PMIC_PCA9450=y
 CONFIG_DM_PMIC_PFUZE100=y
@@ -101,5 +103,9 @@ CONFIG_SPL_SYSRESET=y
 CONFIG_SYSRESET_PSCI=y
 CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+# CONFIG_SPL_DM_USB is not set
+CONFIG_USB_EHCI_HCD=y
 CONFIG_IMX_WATCHDOG=y
 CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/include/configs/verdin-imx8mm.h b/include/configs/verdin-imx8mm.h
index 4751bf5a5a..e2a817891c 100644
--- a/include/configs/verdin-imx8mm.h
+++ b/include/configs/verdin-imx8mm.h
@@ -117,5 +117,10 @@
 #define FEC_QUIRK_ENET_MAC
 #define IMX_FEC_BASE			0x30BE0000
 
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
 #endif /*_VERDIN_IMX8MM_H */
 
-- 
2.30.2

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Tim Harvey]

On Sun, Apr 11, 2021 at 9:35 AM Marek Vasut <marex@denx.de> wrote:
>
> Enable USB host support on MX8MM Verdin.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Cc: Max Krummenacher <max.krummenacher@toradex.com>
> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
> ---
> V2: No change
> ---
>  configs/verdin-imx8mm_defconfig | 8 +++++++-
>  include/configs/verdin-imx8mm.h | 5 +++++
>  2 files changed, 12 insertions(+), 1 deletion(-)
>
> diff --git a/configs/verdin-imx8mm_defconfig b/configs/verdin-imx8mm_defconfig
> index ea0b5978f1..c8c3420b6a 100644
> --- a/configs/verdin-imx8mm_defconfig
> +++ b/configs/verdin-imx8mm_defconfig
> @@ -37,7 +37,6 @@ CONFIG_SPL_BOARD_INIT=y
>  CONFIG_SPL_SEPARATE_BSS=y
>  CONFIG_SPL_I2C_SUPPORT=y
>  CONFIG_SPL_POWER_SUPPORT=y
> -CONFIG_SPL_USB_HOST_SUPPORT=y
>  CONFIG_SPL_WATCHDOG_SUPPORT=y
>  CONFIG_SYS_PROMPT="Verdin iMX8MM # "
>  # CONFIG_BOOTM_NETBSD is not set
> @@ -50,6 +49,7 @@ CONFIG_CMD_FUSE=y
>  CONFIG_CMD_GPIO=y
>  CONFIG_CMD_I2C=y
>  CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
>  CONFIG_CMD_CACHE=y
>  CONFIG_CMD_UUID=y
>  CONFIG_CMD_REGULATOR=y
> @@ -89,6 +89,8 @@ CONFIG_MII=y
>  CONFIG_PINCTRL=y
>  CONFIG_SPL_PINCTRL=y
>  CONFIG_PINCTRL_IMX8M=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_IMX8M_POWER_DOMAIN=y
>  CONFIG_DM_PMIC=y
>  CONFIG_SPL_DM_PMIC_PCA9450=y
>  CONFIG_DM_PMIC_PFUZE100=y
> @@ -101,5 +103,9 @@ CONFIG_SPL_SYSRESET=y
>  CONFIG_SYSRESET_PSCI=y
>  CONFIG_SYSRESET_WATCHDOG=y
>  CONFIG_DM_THERMAL=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +# CONFIG_SPL_DM_USB is not set
> +CONFIG_USB_EHCI_HCD=y
>  CONFIG_IMX_WATCHDOG=y
>  CONFIG_OF_LIBFDT_OVERLAY=y
> diff --git a/include/configs/verdin-imx8mm.h b/include/configs/verdin-imx8mm.h
> index 4751bf5a5a..e2a817891c 100644
> --- a/include/configs/verdin-imx8mm.h
> +++ b/include/configs/verdin-imx8mm.h
> @@ -117,5 +117,10 @@
>  #define FEC_QUIRK_ENET_MAC
>  #define IMX_FEC_BASE                   0x30BE0000
>
> +/* USB Configs */
> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
> +
>  #endif /*_VERDIN_IMX8MM_H */
>
> --
> 2.30.2
>

Marek,

Thanks for your work on USB support for IMX8M!

I'm attempting to add USB support to the venice board following this
example but I think there are still some things missing from the dt to
make this work. I find that mx6_parse_dt_adds failes; Looks like it is
required to have an alias that points to the phy but then it fails
because the phy doesn't have a reg. Also, it would see the
CONFIG_MXC_USB_PORTSC is no longer needed as that is now the default.

Best regards,

Tim

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Ying-Chun Liu]

Hi Marek,

I have the same issue on my iMX8MM based board.
Are you continue working on the patch for iMX8MM or should I dig into
this problem?

I'm asking this just for not duplicating efforts.
So if you are not working on this then I'll see if I can properly
retrieve the necessary patches to make this work.


I think something is missing from previous patch set

https://lists.denx.de/pipermail/u-boot/2020-September/426757.html


Yours,
Paul

Tim Harvey ? 2021/4/20 ??8:33 ??:
> On Sun, Apr 11, 2021 at 9:35 AM Marek Vasut <marex@denx.de> wrote:
>> Enable USB host support on MX8MM Verdin.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>> Cc: Max Krummenacher <max.krummenacher@toradex.com>
>> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
>> ---
>> V2: No change
>> ---
>>  configs/verdin-imx8mm_defconfig | 8 +++++++-
>>  include/configs/verdin-imx8mm.h | 5 +++++
>>  2 files changed, 12 insertions(+), 1 deletion(-)
>>
>> diff --git a/configs/verdin-imx8mm_defconfig b/configs/verdin-imx8mm_defconfig
>> index ea0b5978f1..c8c3420b6a 100644
>> --- a/configs/verdin-imx8mm_defconfig
>> +++ b/configs/verdin-imx8mm_defconfig
>> @@ -37,7 +37,6 @@ CONFIG_SPL_BOARD_INIT=y
>>  CONFIG_SPL_SEPARATE_BSS=y
>>  CONFIG_SPL_I2C_SUPPORT=y
>>  CONFIG_SPL_POWER_SUPPORT=y
>> -CONFIG_SPL_USB_HOST_SUPPORT=y
>>  CONFIG_SPL_WATCHDOG_SUPPORT=y
>>  CONFIG_SYS_PROMPT="Verdin iMX8MM # "
>>  # CONFIG_BOOTM_NETBSD is not set
>> @@ -50,6 +49,7 @@ CONFIG_CMD_FUSE=y
>>  CONFIG_CMD_GPIO=y
>>  CONFIG_CMD_I2C=y
>>  CONFIG_CMD_MMC=y
>> +CONFIG_CMD_USB=y
>>  CONFIG_CMD_CACHE=y
>>  CONFIG_CMD_UUID=y
>>  CONFIG_CMD_REGULATOR=y
>> @@ -89,6 +89,8 @@ CONFIG_MII=y
>>  CONFIG_PINCTRL=y
>>  CONFIG_SPL_PINCTRL=y
>>  CONFIG_PINCTRL_IMX8M=y
>> +CONFIG_POWER_DOMAIN=y
>> +CONFIG_IMX8M_POWER_DOMAIN=y
>>  CONFIG_DM_PMIC=y
>>  CONFIG_SPL_DM_PMIC_PCA9450=y
>>  CONFIG_DM_PMIC_PFUZE100=y
>> @@ -101,5 +103,9 @@ CONFIG_SPL_SYSRESET=y
>>  CONFIG_SYSRESET_PSCI=y
>>  CONFIG_SYSRESET_WATCHDOG=y
>>  CONFIG_DM_THERMAL=y
>> +CONFIG_USB=y
>> +CONFIG_DM_USB=y
>> +# CONFIG_SPL_DM_USB is not set
>> +CONFIG_USB_EHCI_HCD=y
>>  CONFIG_IMX_WATCHDOG=y
>>  CONFIG_OF_LIBFDT_OVERLAY=y
>> diff --git a/include/configs/verdin-imx8mm.h b/include/configs/verdin-imx8mm.h
>> index 4751bf5a5a..e2a817891c 100644
>> --- a/include/configs/verdin-imx8mm.h
>> +++ b/include/configs/verdin-imx8mm.h
>> @@ -117,5 +117,10 @@
>>  #define FEC_QUIRK_ENET_MAC
>>  #define IMX_FEC_BASE                   0x30BE0000
>>
>> +/* USB Configs */
>> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
>> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
>> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>> +
>>  #endif /*_VERDIN_IMX8MM_H */
>>
>> --
>> 2.30.2
>>
> Marek,
>
> Thanks for your work on USB support for IMX8M!
>
> I'm attempting to add USB support to the venice board following this
> example but I think there are still some things missing from the dt to
> make this work. I find that mx6_parse_dt_adds failes; Looks like it is
> required to have an alias that points to the phy but then it fails
> because the phy doesn't have a reg. Also, it would see the
> CONFIG_MXC_USB_PORTSC is no longer needed as that is now the default.
>
> Best regards,
>
> Tim

-------------- next part --------------
A non-text attachment was scrubbed...
Name: OpenPGP_signature
Type: application/pgp-signature
Size: 840 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210422/d2a968d8/attachment.sig>

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Tim Harvey]

On Thu, Apr 22, 2021 at 3:34 AM Ying-Chun Liu (PaulLiu)
<paulliu@debian.org> wrote:
>
> Hi Marek,
>
> I have the same issue on my iMX8MM based board.
> Are you continue working on the patch for iMX8MM or should I dig into
> this problem?
>
> I'm asking this just for not duplicating efforts.
> So if you are not working on this then I'll see if I can properly
> retrieve the necessary patches to make this work.
>
>
> I think something is missing from previous patch set
>
> https://lists.denx.de/pipermail/u-boot/2020-September/426757.html
>
>

Paul,

It's not something missing from Peng's previous patchset since that
didn't support DM. Marek added the dm bits but it requires some dt
changes that are still not present to make mx6_parse_dt_addrs work (or
some changes are needed to that func).

The way mx6_parse_dt_addrs is written you need to have a 'usb0' alias
for example that points to the phy node (compatible 'fsl,usbmisc') but
that is not what has typically been done for USB as typically the
alias points to the host controller instead.

I'm still interested in what Marek tested with and also think there's
a dt patch missing. The aliases should be added to imx8mm.dtsi, but I
also think they should point to the controller and not the phy so
there may be a code change needed as well.

Also, I wasn't aware that the power-domain dt bindings were accepted
upstream to Linux as there has been quite a bit of controversy there.

cc'ing some others that are probably interested in mainline USB on
IMX8M and likely know what's going on with IMX8M power domain. I
regret missing this patchset when it was submitted or I would have
asked these questions then... I just can't keep up with Linux and
U-Boot mailing lists with my work-load in other areas.

Best regards,

Tim

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Marek Vasut]

On 4/20/21 2:33 AM, Tim Harvey wrote:

[...]

>> +/* USB Configs */
>> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
>> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
>> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>> +
>>   #endif /*_VERDIN_IMX8MM_H */
>>
>> --
>> 2.30.2
>>
> 
> Marek,
> 
> Thanks for your work on USB support for IMX8M!
> 
> I'm attempting to add USB support to the venice board following this
> example but I think there are still some things missing from the dt to
> make this work. I find that mx6_parse_dt_adds failes; Looks like it is
> required to have an alias that points to the phy but then it fails
> because the phy doesn't have a reg. Also, it would see the
> CONFIG_MXC_USB_PORTSC is no longer needed as that is now the default.

Have a look at this patch:

https://source.denx.de/u-boot/custodians/u-boot-usb/-/commit/8203ee09275c30766a1fd1cf19c60a904ee72f8c

That should fix it for you.

It would be good however if you could take the mx6 ventana and test the 
driver there, and possibly submit fixes in case the USB is still broken 
there. What would be even better is if you could implement the MXS PHY 
driver, so all the !CONFIG_PHY stuff can be removed for MX6 too. That 
shouldn't be much effort.

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Tim Harvey]

On Thu, Apr 22, 2021 at 12:16 PM Marek Vasut <marex@denx.de> wrote:
>
> On 4/20/21 2:33 AM, Tim Harvey wrote:
>
> [...]
>
> >> +/* USB Configs */
> >> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> >> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
> >> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
> >> +
> >>   #endif /*_VERDIN_IMX8MM_H */
> >>
> >> --
> >> 2.30.2
> >>
> >
> > Marek,
> >
> > Thanks for your work on USB support for IMX8M!
> >
> > I'm attempting to add USB support to the venice board following this
> > example but I think there are still some things missing from the dt to
> > make this work. I find that mx6_parse_dt_adds failes; Looks like it is
> > required to have an alias that points to the phy but then it fails
> > because the phy doesn't have a reg. Also, it would see the
> > CONFIG_MXC_USB_PORTSC is no longer needed as that is now the default.
>
> Have a look at this patch:
>
> https://source.denx.de/u-boot/custodians/u-boot-usb/-/commit/8203ee09275c30766a1fd1cf19c60a904ee72f8c
>
> That should fix it for you.
>
> It would be good however if you could take the mx6 ventana and test the
> driver there, and possibly submit fixes in case the USB is still broken
> there. What would be even better is if you could implement the MXS PHY
> driver, so all the !CONFIG_PHY stuff can be removed for MX6 too. That
> shouldn't be much effort.

Marek,

That does resolve the issue with mx6_parse_dt_adds failing and works
for IMX8MM host mode (and likely peripheral mode) but not for otg. For
otg we also need something like:
@@ -523,7 +568,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
                        plat->init_type = USB_INIT_DEVICE;
                else
                        plat->init_type = USB_INIT_HOST;
-       } else if (is_mx7()) {
+       } else if (is_mx7() || is_imx8mm()) {
                phy_status = (void __iomem *)(addr +
                                              USBNC_PHY_STATUS_OFFSET);
                val = readl(phy_status);

but then the issue is we hang due to the otg power domain not being
enabled when ehci_usb_of_to_plat is called and I'm not quite clear why
that is. Why would the power domain get probed/enabled for the usbotg2
bus but not the usbotg1 bus? Here is some debugging:
u-boot=> usb start
starting USB...
Bus usb at 32e40000: ehci_usb_phy_mode usb at 32e40000
usb at 32e40000 probe ret=-22
probe failed, error -22
^^^ probe fails here because ehci_usb_phy_mode returns EINVAL for
dr_mode=otg but if we try to read the phy_status reg we will hang b/c
power domain is not enabled yet
Bus usb at 32e50000: imx8m_power_domain_probe gpc at 303a0000
imx8m_power_domain_probe pgc
^^^ why did power domain get probed on the 2nd bus and not the first?
imx8m_power_domain_probe power-domain at 0
imx8m_power_domain_probe power-domain at 3
imx8m_power_domain_on power-domain at 3
imx8m_power_domain_on power-domain at 0
ehci_usb_probe usb at 32e50000
USB EHCI 1.00
usb at 32e50000 probe ret=0
scanning bus usb at 32e50000 for devices... imx8m_power_domain_on power-domain at 3
imx8m_power_domain_on power-domain at 0
3 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
u-boot=>

I also verified your patch does not break USB for IMX6Q/DL ventana as well.

I am still a bit concerned that the power-domain patches you merged in
this series are introducing bindings that are not approved upstream:
d78f7d8199 ARM: dts: imx8mn: Add power domain nodes
f0e10e33e5 ARM: dts: imx8mm: Add power domain nodes

Are you under the impression that is what will go upstream? I'm still
waiting to see what this 'virtual power-domain' patch looks like that
I believe Abel or Jacky was going to work on. Perhaps you, Adam, or
Frieder took part in that discussion?

Best regards,

Tim

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Marek Vasut]

On 4/23/21 5:04 PM, Tim Harvey wrote:
> On Thu, Apr 22, 2021 at 12:16 PM Marek Vasut <marex@denx.de> wrote:
>>
>> On 4/20/21 2:33 AM, Tim Harvey wrote:
>>
>> [...]
>>
>>>> +/* USB Configs */
>>>> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
>>>> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
>>>> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>>>> +
>>>>    #endif /*_VERDIN_IMX8MM_H */
>>>>
>>>> --
>>>> 2.30.2
>>>>
>>>
>>> Marek,
>>>
>>> Thanks for your work on USB support for IMX8M!
>>>
>>> I'm attempting to add USB support to the venice board following this
>>> example but I think there are still some things missing from the dt to
>>> make this work. I find that mx6_parse_dt_adds failes; Looks like it is
>>> required to have an alias that points to the phy but then it fails
>>> because the phy doesn't have a reg. Also, it would see the
>>> CONFIG_MXC_USB_PORTSC is no longer needed as that is now the default.
>>
>> Have a look at this patch:
>>
>> https://source.denx.de/u-boot/custodians/u-boot-usb/-/commit/8203ee09275c30766a1fd1cf19c60a904ee72f8c
>>
>> That should fix it for you.
>>
>> It would be good however if you could take the mx6 ventana and test the
>> driver there, and possibly submit fixes in case the USB is still broken
>> there. What would be even better is if you could implement the MXS PHY
>> driver, so all the !CONFIG_PHY stuff can be removed for MX6 too. That
>> shouldn't be much effort.
> 
> Marek,
> 
> That does resolve the issue with mx6_parse_dt_adds failing and works
> for IMX8MM host mode (and likely peripheral mode) but not for otg. For
> otg we also need something like:
> @@ -523,7 +568,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
>                          plat->init_type = USB_INIT_DEVICE;
>                  else
>                          plat->init_type = USB_INIT_HOST;
> -       } else if (is_mx7()) {
> +       } else if (is_mx7() || is_imx8mm()) {
>                  phy_status = (void __iomem *)(addr +
>                                                USBNC_PHY_STATUS_OFFSET);
>                  val = readl(phy_status);
> 
> but then the issue is we hang due to the otg power domain not being
> enabled when ehci_usb_of_to_plat is called and I'm not quite clear why
> that is.

ehci_usb_phy_mode() is called from ehci_usb_of_to_plat(), which happens 
before probe(), so the power domain at that point is off. You would have 
to move that entire code to probe() to get OTG working properly, without 
the current workaround.

> Why would the power domain get probed/enabled for the usbotg2
> bus but not the usbotg1 bus? Here is some debugging:
> u-boot=> usb start
> starting USB...
> Bus usb at 32e40000: ehci_usb_phy_mode usb at 32e40000
> usb at 32e40000 probe ret=-22
> probe failed, error -22
> ^^^ probe fails here because ehci_usb_phy_mode returns EINVAL for
> dr_mode=otg but if we try to read the phy_status reg we will hang b/c
> power domain is not enabled yet
> Bus usb at 32e50000: imx8m_power_domain_probe gpc at 303a0000
> imx8m_power_domain_probe pgc
> ^^^ why did power domain get probed on the 2nd bus and not the first?

I don't know, can you have a look ?

> imx8m_power_domain_probe power-domain at 0
> imx8m_power_domain_probe power-domain at 3
> imx8m_power_domain_on power-domain at 3
> imx8m_power_domain_on power-domain at 0
> ehci_usb_probe usb at 32e50000
> USB EHCI 1.00
> usb at 32e50000 probe ret=0
> scanning bus usb at 32e50000 for devices... imx8m_power_domain_on power-domain at 3
> imx8m_power_domain_on power-domain at 0
> 3 USB Device(s) found
>         scanning usb for storage devices... 0 Storage Device(s) found
> u-boot=>
> 
> I also verified your patch does not break USB for IMX6Q/DL ventana as well.

That's good, thank you

> I am still a bit concerned that the power-domain patches you merged in
> this series are introducing bindings that are not approved upstream:
> d78f7d8199 ARM: dts: imx8mn: Add power domain nodes
> f0e10e33e5 ARM: dts: imx8mm: Add power domain nodes
> 
> Are you under the impression that is what will go upstream?

Pretty much, yes. And if there are some changes further down the line, 
we can pick those later when they hit upstream. I think this is better 
than having no working USB at all.

> I'm still
> waiting to see what this 'virtual power-domain' patch looks like that
> I believe Abel or Jacky was going to work on. Perhaps you, Adam, or
> Frieder took part in that discussion?

That is still going on, yes.

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Tim Harvey]

On Fri, Apr 23, 2021 at 8:21 AM Marek Vasut <marex@denx.de> wrote:
>
> On 4/23/21 5:04 PM, Tim Harvey wrote:
> > On Thu, Apr 22, 2021 at 12:16 PM Marek Vasut <marex@denx.de> wrote:
> >>
> >> On 4/20/21 2:33 AM, Tim Harvey wrote:
> >>
> >> [...]
> >>
> >>>> +/* USB Configs */
> >>>> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> >>>> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
> >>>> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
> >>>> +
> >>>>    #endif /*_VERDIN_IMX8MM_H */
> >>>>
> >>>> --
> >>>> 2.30.2
> >>>>
> >>>
> >>> Marek,
> >>>
> >>> Thanks for your work on USB support for IMX8M!
> >>>
> >>> I'm attempting to add USB support to the venice board following this
> >>> example but I think there are still some things missing from the dt to
> >>> make this work. I find that mx6_parse_dt_adds failes; Looks like it is
> >>> required to have an alias that points to the phy but then it fails
> >>> because the phy doesn't have a reg. Also, it would see the
> >>> CONFIG_MXC_USB_PORTSC is no longer needed as that is now the default.
> >>
> >> Have a look at this patch:
> >>
> >> https://source.denx.de/u-boot/custodians/u-boot-usb/-/commit/8203ee09275c30766a1fd1cf19c60a904ee72f8c
> >>
> >> That should fix it for you.
> >>
> >> It would be good however if you could take the mx6 ventana and test the
> >> driver there, and possibly submit fixes in case the USB is still broken
> >> there. What would be even better is if you could implement the MXS PHY
> >> driver, so all the !CONFIG_PHY stuff can be removed for MX6 too. That
> >> shouldn't be much effort.
> >
> > Marek,
> >
> > That does resolve the issue with mx6_parse_dt_adds failing and works
> > for IMX8MM host mode (and likely peripheral mode) but not for otg. For
> > otg we also need something like:
> > @@ -523,7 +568,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
> >                          plat->init_type = USB_INIT_DEVICE;
> >                  else
> >                          plat->init_type = USB_INIT_HOST;
> > -       } else if (is_mx7()) {
> > +       } else if (is_mx7() || is_imx8mm()) {
> >                  phy_status = (void __iomem *)(addr +
> >                                                USBNC_PHY_STATUS_OFFSET);
> >                  val = readl(phy_status);
> >
> > but then the issue is we hang due to the otg power domain not being
> > enabled when ehci_usb_of_to_plat is called and I'm not quite clear why
> > that is.
>
> ehci_usb_phy_mode() is called from ehci_usb_of_to_plat(), which happens
> before probe(), so the power domain at that point is off. You would have
> to move that entire code to probe() to get OTG working properly, without
> the current workaround.
>
> > Why would the power domain get probed/enabled for the usbotg2
> > bus but not the usbotg1 bus? Here is some debugging:
> > u-boot=> usb start
> > starting USB...
> > Bus usb at 32e40000: ehci_usb_phy_mode usb at 32e40000
> > usb at 32e40000 probe ret=-22
> > probe failed, error -22
> > ^^^ probe fails here because ehci_usb_phy_mode returns EINVAL for
> > dr_mode=otg but if we try to read the phy_status reg we will hang b/c
> > power domain is not enabled yet
> > Bus usb at 32e50000: imx8m_power_domain_probe gpc at 303a0000
> > imx8m_power_domain_probe pgc
> > ^^^ why did power domain get probed on the 2nd bus and not the first?
>
> I don't know, can you have a look ?

Marek,

The reg domain does not get enabled for usbotg1 because
device_of_to_plat gets called 'before' dev_power_domain_on in
device_probe.

The following will get imx8mm USB otg working:

For OTG defer setting type until probe after clock and power have been
brought up.
index 06be9deaaa..2183ae4f9d 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -523,7 +523,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
                        plat->init_type = USB_INIT_DEVICE;
                else
                        plat->init_type = USB_INIT_HOST;
-       } else if (is_mx7()) {
+       } else if (is_mx7() || is_imx8mm()) {
                phy_status = (void __iomem *)(addr +
                                              USBNC_PHY_STATUS_OFFSET);
                val = readl(phy_status);
@@ -555,7 +555,10 @@ static int ehci_usb_of_to_plat(struct udevice *dev)
                break;
        case USB_DR_MODE_OTG:
        case USB_DR_MODE_UNKNOWN:
-               return ehci_usb_phy_mode(dev);
+               if (is_imx8mm())
+                       plat->init_type = USB_INIT_HOST;
+               else
+                       return ehci_usb_phy_mode(dev);
        };

        return 0;
@@ -657,6 +660,13 @@ static int ehci_usb_probe(struct udevice *dev)
        mdelay(1);
 #endif

+       if (is_imx8mm() && (usb_get_dr_mode(dev_ofnode(dev)) ==
USB_DR_MODE_OTG)) {
+               ret = ehci_usb_phy_mode(dev);
+               if (ret)
+                       return ret;
+               priv->init_type = plat->init_type;
+       };
+
 #if CONFIG_IS_ENABLED(DM_REGULATOR)
        ret = device_get_supply_regulator(dev, "vbus-supply",
                                          &priv->vbus_supply);


>
> > imx8m_power_domain_probe power-domain at 0
> > imx8m_power_domain_probe power-domain at 3
> > imx8m_power_domain_on power-domain at 3
> > imx8m_power_domain_on power-domain at 0
> > ehci_usb_probe usb at 32e50000
> > USB EHCI 1.00
> > usb at 32e50000 probe ret=0
> > scanning bus usb at 32e50000 for devices... imx8m_power_domain_on power-domain at 3
> > imx8m_power_domain_on power-domain at 0
> > 3 USB Device(s) found
> >         scanning usb for storage devices... 0 Storage Device(s) found
> > u-boot=>
> >
> > I also verified your patch does not break USB for IMX6Q/DL ventana as well.
>
> That's good, thank you
>
> > I am still a bit concerned that the power-domain patches you merged in
> > this series are introducing bindings that are not approved upstream:
> > d78f7d8199 ARM: dts: imx8mn: Add power domain nodes
> > f0e10e33e5 ARM: dts: imx8mm: Add power domain nodes
> >
> > Are you under the impression that is what will go upstream?
>
> Pretty much, yes. And if there are some changes further down the line,
> we can pick those later when they hit upstream. I think this is better
> than having no working USB at all.
>
> > I'm still
> > waiting to see what this 'virtual power-domain' patch looks like that
> > I believe Abel or Jacky was going to work on. Perhaps you, Adam, or
> > Frieder took part in that discussion?
>
> That is still going on, yes.

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Marek Vasut]

On 4/27/21 2:01 AM, Tim Harvey wrote:
[...]
>>> Why would the power domain get probed/enabled for the usbotg2
>>> bus but not the usbotg1 bus? Here is some debugging:
>>> u-boot=> usb start
>>> starting USB...
>>> Bus usb at 32e40000: ehci_usb_phy_mode usb at 32e40000
>>> usb at 32e40000 probe ret=-22
>>> probe failed, error -22
>>> ^^^ probe fails here because ehci_usb_phy_mode returns EINVAL for
>>> dr_mode=otg but if we try to read the phy_status reg we will hang b/c
>>> power domain is not enabled yet
>>> Bus usb at 32e50000: imx8m_power_domain_probe gpc at 303a0000
>>> imx8m_power_domain_probe pgc
>>> ^^^ why did power domain get probed on the 2nd bus and not the first?
>>
>> I don't know, can you have a look ?
> 
> Marek,
> 
> The reg domain does not get enabled for usbotg1 because
> device_of_to_plat gets called 'before' dev_power_domain_on in
> device_probe.
> 
> The following will get imx8mm USB otg working:
> 
> For OTG defer setting type until probe after clock and power have been
> brought up.
> index 06be9deaaa..2183ae4f9d 100644
> --- a/drivers/usb/host/ehci-mx6.c
> +++ b/drivers/usb/host/ehci-mx6.c
> @@ -523,7 +523,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
>                          plat->init_type = USB_INIT_DEVICE;
>                  else
>                          plat->init_type = USB_INIT_HOST;
> -       } else if (is_mx7()) {
> +       } else if (is_mx7() || is_imx8mm()) {
>                  phy_status = (void __iomem *)(addr +
>                                                USBNC_PHY_STATUS_OFFSET);
>                  val = readl(phy_status);
> @@ -555,7 +555,10 @@ static int ehci_usb_of_to_plat(struct udevice *dev)
>                  break;
>          case USB_DR_MODE_OTG:
>          case USB_DR_MODE_UNKNOWN:
> -               return ehci_usb_phy_mode(dev);
> +               if (is_imx8mm())

Does this mean OTG doesn't work on the 8MM then ?

> +                       plat->init_type = USB_INIT_HOST;
> +               else
> +                       return ehci_usb_phy_mode(dev);
>          };
> 
>          return 0;
> @@ -657,6 +660,13 @@ static int ehci_usb_probe(struct udevice *dev)
>          mdelay(1);
>   #endif
> 
> +       if (is_imx8mm() && (usb_get_dr_mode(dev_ofnode(dev)) ==
> USB_DR_MODE_OTG)) {
> +               ret = ehci_usb_phy_mode(dev);
> +               if (ret)
> +                       return ret;
> +               priv->init_type = plat->init_type;
> +       };

I have to wonder, why not move the whole OTG/Host/Device detection to 
probe then ?

Also, could you submit a regular patch ?

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Tim Harvey]

On Mon, Apr 26, 2021, 5:35 PM Marek Vasut <marex@denx.de> wrote:
>
> On 4/27/21 2:01 AM, Tim Harvey wrote:
> [...]
> >>> Why would the power domain get probed/enabled for the usbotg2
> >>> bus but not the usbotg1 bus? Here is some debugging:
> >>> u-boot=> usb start
> >>> starting USB...
> >>> Bus usb at 32e40000: ehci_usb_phy_mode usb at 32e40000
> >>> usb at 32e40000 probe ret=-22
> >>> probe failed, error -22
> >>> ^^^ probe fails here because ehci_usb_phy_mode returns EINVAL for
> >>> dr_mode=otg but if we try to read the phy_status reg we will hang b/c
> >>> power domain is not enabled yet
> >>> Bus usb at 32e50000: imx8m_power_domain_probe gpc at 303a0000
> >>> imx8m_power_domain_probe pgc
> >>> ^^^ why did power domain get probed on the 2nd bus and not the first?
> >>
> >> I don't know, can you have a look ?
> >
> > Marek,
> >
> > The reg domain does not get enabled for usbotg1 because
> > device_of_to_plat gets called 'before' dev_power_domain_on in
> > device_probe.
> >
> > The following will get imx8mm USB otg working:
> >
> > For OTG defer setting type until probe after clock and power have been
> > brought up.
> > index 06be9deaaa..2183ae4f9d 100644
> > --- a/drivers/usb/host/ehci-mx6.c
> > +++ b/drivers/usb/host/ehci-mx6.c
> > @@ -523,7 +523,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
> >                          plat->init_type = USB_INIT_DEVICE;
> >                  else
> >                          plat->init_type = USB_INIT_HOST;
> > -       } else if (is_mx7()) {
> > +       } else if (is_mx7() || is_imx8mm()) {
> >                  phy_status = (void __iomem *)(addr +
> >                                                USBNC_PHY_STATUS_OFFSET);
> >                  val = readl(phy_status);
> > @@ -555,7 +555,10 @@ static int ehci_usb_of_to_plat(struct udevice *dev)
> >                  break;
> >          case USB_DR_MODE_OTG:
> >          case USB_DR_MODE_UNKNOWN:
> > -               return ehci_usb_phy_mode(dev);
> > +               if (is_imx8mm())
>
> Does this mean OTG doesn't work on the 8MM then ?

IMX8MM USB in general still doesn't work without your:
usb: ehci-mx6: Limit PHY address parsing to !CONFIG_PHY

With your patch, IMX8MM 'host' works but 'otg' will fail probe with
-22 (due ehci_usb_phy_mode called from of_to_plat and it not having a
case for imx8mm)

>
> > +                       plat->init_type = USB_INIT_HOST;
> > +               else
> > +                       return ehci_usb_phy_mode(dev);
> >          };
> >
> >          return 0;
> > @@ -657,6 +660,13 @@ static int ehci_usb_probe(struct udevice *dev)
> >          mdelay(1);
> >   #endif
> >
> > +       if (is_imx8mm() && (usb_get_dr_mode(dev_ofnode(dev)) ==
> > USB_DR_MODE_OTG)) {
> > +               ret = ehci_usb_phy_mode(dev);
> > +               if (ret)
> > +                       return ret;
> > +               priv->init_type = plat->init_type;
> > +       };
>
> I have to wonder, why not move the whole OTG/Host/Device detection to
> probe then ?

Yes, I think that is the right thing to do.

>
> Also, could you submit a regular patch ?

Yes, I will post patches to fix IMX8MM OTG. Can you submit your 'usb:
ehci-mx6: Limit PHY address parsing to !CONFIG_PHY' patch so I can go
on top of that or can I just pull that into my series?

Best regards,

Tim

[PATCH V2 24/24] ARM: imx8m: verdin-imx8mm: Enable USB Host support

[Adam Ford]

On Tue, Apr 27, 2021 at 10:50 AM Tim Harvey <tharvey@gateworks.com> wrote:
>
> On Mon, Apr 26, 2021, 5:35 PM Marek Vasut <marex@denx.de> wrote:
> >
> > On 4/27/21 2:01 AM, Tim Harvey wrote:
> > [...]
> > >>> Why would the power domain get probed/enabled for the usbotg2
> > >>> bus but not the usbotg1 bus? Here is some debugging:
> > >>> u-boot=> usb start
> > >>> starting USB...
> > >>> Bus usb at 32e40000: ehci_usb_phy_mode usb at 32e40000
> > >>> usb at 32e40000 probe ret=-22
> > >>> probe failed, error -22
> > >>> ^^^ probe fails here because ehci_usb_phy_mode returns EINVAL for
> > >>> dr_mode=otg but if we try to read the phy_status reg we will hang b/c
> > >>> power domain is not enabled yet
> > >>> Bus usb at 32e50000: imx8m_power_domain_probe gpc at 303a0000
> > >>> imx8m_power_domain_probe pgc
> > >>> ^^^ why did power domain get probed on the 2nd bus and not the first?
> > >>
> > >> I don't know, can you have a look ?
> > >
> > > Marek,
> > >
> > > The reg domain does not get enabled for usbotg1 because
> > > device_of_to_plat gets called 'before' dev_power_domain_on in
> > > device_probe.
> > >
> > > The following will get imx8mm USB otg working:
> > >
> > > For OTG defer setting type until probe after clock and power have been
> > > brought up.
> > > index 06be9deaaa..2183ae4f9d 100644
> > > --- a/drivers/usb/host/ehci-mx6.c
> > > +++ b/drivers/usb/host/ehci-mx6.c
> > > @@ -523,7 +523,7 @@ static int ehci_usb_phy_mode(struct udevice *dev)
> > >                          plat->init_type = USB_INIT_DEVICE;
> > >                  else
> > >                          plat->init_type = USB_INIT_HOST;
> > > -       } else if (is_mx7()) {
> > > +       } else if (is_mx7() || is_imx8mm()) {
> > >                  phy_status = (void __iomem *)(addr +
> > >                                                USBNC_PHY_STATUS_OFFSET);
> > >                  val = readl(phy_status);
> > > @@ -555,7 +555,10 @@ static int ehci_usb_of_to_plat(struct udevice *dev)
> > >                  break;
> > >          case USB_DR_MODE_OTG:
> > >          case USB_DR_MODE_UNKNOWN:
> > > -               return ehci_usb_phy_mode(dev);
> > > +               if (is_imx8mm())
> >
> > Does this mean OTG doesn't work on the 8MM then ?
>
> IMX8MM USB in general still doesn't work without your:
> usb: ehci-mx6: Limit PHY address parsing to !CONFIG_PHY
>
> With your patch, IMX8MM 'host' works but 'otg' will fail probe with
> -22 (due ehci_usb_phy_mode called from of_to_plat and it not having a
> case for imx8mm)
>
> >
> > > +                       plat->init_type = USB_INIT_HOST;
> > > +               else
> > > +                       return ehci_usb_phy_mode(dev);
> > >          };
> > >
> > >          return 0;
> > > @@ -657,6 +660,13 @@ static int ehci_usb_probe(struct udevice *dev)
> > >          mdelay(1);
> > >   #endif
> > >
> > > +       if (is_imx8mm() && (usb_get_dr_mode(dev_ofnode(dev)) ==
> > > USB_DR_MODE_OTG)) {
> > > +               ret = ehci_usb_phy_mode(dev);
> > > +               if (ret)
> > > +                       return ret;
> > > +               priv->init_type = plat->init_type;
> > > +       };
> >
> > I have to wonder, why not move the whole OTG/Host/Device detection to
> > probe then ?
>
> Yes, I think that is the right thing to do.
>
> >
> > Also, could you submit a regular patch ?
>
> Yes, I will post patches to fix IMX8MM OTG. Can you submit your 'usb:
> ehci-mx6: Limit PHY address parsing to !CONFIG_PHY' patch so I can go
> on top of that or can I just pull that into my series?

If you want me to test it on either a Mini or Nano, feel free to CC me
as well.  I was out of town the last week, so I wasn't in a place to
do any work.
I am a little behind, so I might need some pointers to prerequisite
patches if they're necessary.

thanks,

adam

>
> Best regards,
>
> Tim

[PATCH V2 01/24] phy: nop-phy: Add standard usb-nop-xceiv compat string

[Sean Anderson]

On 4/11/21 12:28 PM, Marek Vasut wrote:
> The USB no-op PHY uses "usb-nop-xceiv" compatible string. This driver is
> compatible with USB no-op PHY, so add the compatible string.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
> Cc: Murali Karicheri <m-karicheri2@ti.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Ye Li <ye.li@nxp.com>
> Cc: uboot-imx <uboot-imx@nxp.com>
> ---
> V2: No change
> ---
>   drivers/phy/nop-phy.c | 1 +
>   1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/phy/nop-phy.c b/drivers/phy/nop-phy.c
> index 84aac80623..9f12ebc062 100644
> --- a/drivers/phy/nop-phy.c
> +++ b/drivers/phy/nop-phy.c
> @@ -43,6 +43,7 @@ static int nop_phy_probe(struct udevice *dev)
>   
>   static const struct udevice_id nop_phy_ids[] = {
>   	{ .compatible = "nop-phy" },
> +	{ .compatible = "usb-nop-xceiv" },
>   	{ }
>   };
>   
> 

For the whole series (on i.MX6ULLEVK with mx6ul_14x14_evk_defconfig):

Tested-by: Sean Anderson <sean.anderson@seco.com>