* IRQ issues with multiple SiI3114's on Kernel 3.2
@ 2012-07-27 16:40 Stirling Westrup
2012-07-27 17:24 ` Stan Hoeppner
0 siblings, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-07-27 16:40 UTC (permalink / raw)
To: linux-ide
I recently purchased a large system for use as a backup server for a
pair of small businesses. It contains a boot drive plus 10 more
storage drives. Despite having three onboard SATA controllers, the
motherboard didn't have enough SATA connectors for all the drives, so
I installed a pair of identical SiI3114 raid cards to handle the extra
connections. It has a Sandy Bridge chipset, so I installed a 3.2
kernel.
# uname -a
Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
x86_64 GNU/Linux
# lspci
00:00.0 Host bridge: Intel Corporation Sandy Bridge DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root
Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation Sandy Bridge
Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation Cougar Point HECI
Controller #1 (rev 04)
00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network
Connection (rev 05)
00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced
Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation Cougar Point High Definition
Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root
Port 1 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root
Port 2 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root
Port 4 (rev b5)
00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root
Port 5 (rev b5)
00:1c.6 PCI bridge: Intel Corporation 82801 PCI Bridge (rev b5)
00:1c.7 PCI bridge: Intel Corporation Cougar Point PCI Express Root
Port 8 (rev b5)
00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced
Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation Cougar Point LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA
AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05)
03:00.0 USB Controller: Device 1b21:1042
04:00.0 SATA controller: JMicron Technology Corp. JMB362 AHCI
Controller (rev 10)
05:00.0 USB Controller: Device 1b21:1042
06:00.0 PCI bridge: Device 1b21:1080 (rev 01)
07:00.0 RAID bus controller: Silicon Image, Inc. SiI 3114
[SATALink/SATARaid] Serial ATA Controller (rev 02)
07:01.0 RAID bus controller: Silicon Image, Inc. SiI 3114
[SATALink/SATARaid] Serial ATA Controller (rev 02)
07:02.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire
II(M)] IEEE 1394 OHCI Controller (rev c0)
08:00.0 SATA controller: Marvell Technology Group Ltd. Device 9172 (rev 11)
The drives are connect in the following layout:
# ls -la /dev/disk/by-path/
total 0
drwxr-xr-x 2 root root 340 Jul 27 00:11 .
drwxr-xr-x 6 root root 120 Jul 27 00:11 ..
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:00:1f.2-scsi-0:0:0:0
-> ../../sr0
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:00:1f.2-scsi-1:0:0:0
-> ../../sda
lrwxrwxrwx 1 root root 10 Jul 27 00:11
pci-0000:00:1f.2-scsi-1:0:0:0-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 Jul 27 00:11
pci-0000:00:1f.2-scsi-1:0:0:0-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 Jul 27 00:11
pci-0000:00:1f.2-scsi-1:0:0:0-part3 -> ../../sda3
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:00:1f.2-scsi-2:0:0:0
-> ../../sdb
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:00.0-scsi-0:0:0:0
-> ../../sdd
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:00.0-scsi-1:0:0:0
-> ../../sde
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:00.0-scsi-2:0:0:0
-> ../../sdf
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:00.0-scsi-3:0:0:0
-> ../../sdg
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:01.0-scsi-0:0:0:0
-> ../../sdh
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:01.0-scsi-1:0:0:0
-> ../../sdi
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:01.0-scsi-2:0:0:0
-> ../../sdj
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:07:01.0-scsi-3:0:0:0
-> ../../sdk
lrwxrwxrwx 1 root root 9 Jul 27 00:11 pci-0000:08:00.0-scsi-0:0:0:0
-> ../../sdc
/dev/sda is the boot drive, and along with /dev/sdb is controlled by
the onboard Cougar Point controller.
/dev/sdc is controlled via the Marvell Technology controller.
/dev/sdd through /dev/sdg is controlled by the first SiI3114
/dev/sdh through /dev/sdk is controlled by the first SiI3114
Now, since I've been burned by hardware raid controllers dying in the
past, and taking their drives with them, I did a (perhaps foolish)
thing, and I
striped my raids ACROSS the two SiI3114s. That is, I built two raid6's
with the following components:
raid6: /dev/md0: /dev/sdb, /dev/sdd, /dev/sde, /dev/sdh, /dev/sdi
raid6: /dev/md1: /dev/sdc, /dev/sdf, /dev/sdg, /dev/sdj, /dev/sdk
Thus, each raid is built upon three different SATA controllers, and
loss of any one controller and all attached drives is recoverable.
Okay, enough background. Here's the issue: I had no trouble building
and sync'ing the first array, but when I try to sync the second array,
I always get the following dmesg an hour or so into the process:
irq 19: nobody cared (try booting with the "irqpoll" option)
[ 346.120572] Pid: 1100, comm: md1_resync Not tainted 3.2.0-0.bpo.2-amd64 #1
[ 346.120573] Call Trace:
...
[ 346.120697] handlers:
[ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
[ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
[ 346.120703] Disabling IRQ #19
[ 346.122145] sched: RT throttling activated
>From this point onward syncing drops to a tiny fraction of its
previous speed. I've tried booting with 'irqpoll' as the error message
suggests, but it has had no effect. I'm really not sure if there is a
conflict between my two SiI3114's or between the SiI's and the Marvell
controller (although I've never had an issue with Marvell in the
past), nor how to go about diagnosing or fixing this. I'll include a
full dmesg dump below, as well as my currently loaded modules. If
anyone wants any further info, just ask.
# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-0.bpo.2-amd64 (Debian
3.2.20-1~bpo60+1) (debian-kernel@lists.debian.org) (gcc version 4.4.5
(Debian 4.4.5-8) ) #1 SMP Fri Jun 29 20:42:29 UTC 2012
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.2.0-0.bpo.2-amd64
root=UUID=118651d8-368b-4b99-b34f-54d30ec810cd ro irqpoll quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000099000 (usable)
[ 0.000000] BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
[ 0.000000] BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
[ 0.000000] BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
[ 0.000000] BIOS-e820: 0000000040200000 - 00000000da391000 (usable)
[ 0.000000] BIOS-e820: 00000000da391000 - 00000000da941000 (reserved)
[ 0.000000] BIOS-e820: 00000000da941000 - 00000000dab86000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dab86000 - 00000000dab94000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dab94000 - 00000000dabc1000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dabc1000 - 00000000dabc6000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dabc6000 - 00000000dac09000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dac09000 - 00000000db000000 (usable)
[ 0.000000] BIOS-e820: 00000000db800000 - 00000000dfa00000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed04000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000021f600000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: System manufacturer System Product Name/P8Z68-V
PRO GEN3, BIOS 3202 02/17/2012
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x21f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask E00000000 write-back
[ 0.000000] 1 base 200000000 mask FE0000000 write-back
[ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 3 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 4 base 0DB800000 mask FFF800000 uncachable
[ 0.000000] 5 base 21F800000 mask FFF800000 uncachable
[ 0.000000] 6 base 21F600000 mask FFFE00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000db800000 - 0000000100000000
(usable) ==> (reserved)
[ 0.000000] last_pfn = 0xdb000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fcde0] fcde0
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000094000] 94000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-00000000db000000
[ 0.000000] 0000000000 - 00db000000 page 2M
[ 0.000000] kernel direct mapping tables up to db000000 @ 1fffb000-20000000
[ 0.000000] init_memory_mapping: 0000000100000000-000000021f600000
[ 0.000000] 0100000000 - 021f600000 page 2M
[ 0.000000] kernel direct mapping tables up to 21f600000 @ daff6000-db000000
[ 0.000000] RAMDISK: 17d91000 - 18040000
[ 0.000000] ACPI: RSDP 00000000000f0450 00024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 00000000dab86070 00064 (v01 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 00000000dab91c68 000F4 (v04 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 00000000dab86168 0BAFE (v02 ALASKA A M I
00000015 INTL 20051117)
[ 0.000000] ACPI: FACS 00000000dabbff80 00040
[ 0.000000] ACPI: APIC 00000000dab91d60 00072 (v03 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 00000000dab91dd8 0003C (v01 ALASKA A M I
01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000dab91e18 00038 (v01 ALASKA A M I
01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 00000000dab91e50 0036D (v01 SataRe SataTabl
00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 00000000dab921c0 009AA (v01 PmRef Cpu0Ist
00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000dab92b70 00A92 (v01 PmRef CpuPm
00003000 INTL 20051117)
[ 0.000000] ACPI: BGRT 00000000dab93608 00038 (v00 ALASKA A M I
01072009 AMI 00010013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000021f600000
[ 0.000000] Initmem setup node 0 0000000000000000-000000021f600000
[ 0.000000] NODE_DATA [000000021f5fb000 - 000000021f5fffff]
[ 0.000000] [ffffea0000000000-ffffea00077fffff] PMD ->
[ffff880216c00000-ffff88021ddfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x0021f600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x00000099
[ 0.000000] 0: 0x00000100 -> 0x00020000
[ 0.000000] 0: 0x00020200 -> 0x00040000
[ 0.000000] 0: 0x00040200 -> 0x000da391
[ 0.000000] 0: 0x000dac09 -> 0x000db000
[ 0.000000] 0: 0x00100000 -> 0x0021f600
[ 0.000000] On node 0 totalpages: 2070801
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3916 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 875456 pages, LIFO batch:31
[ 0.000000] Normal zone: 16093 pages used for memmap
[ 0.000000] Normal zone: 1160995 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 0000000000099000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[ 0.000000] PM: Registered nosave memory: 0000000040000000 - 0000000040200000
[ 0.000000] PM: Registered nosave memory: 00000000da391000 - 00000000da941000
[ 0.000000] PM: Registered nosave memory: 00000000da941000 - 00000000dab86000
[ 0.000000] PM: Registered nosave memory: 00000000dab86000 - 00000000dab94000
[ 0.000000] PM: Registered nosave memory: 00000000dab94000 - 00000000dabc1000
[ 0.000000] PM: Registered nosave memory: 00000000dabc1000 - 00000000dabc6000
[ 0.000000] PM: Registered nosave memory: 00000000dabc6000 - 00000000dac09000
[ 0.000000] PM: Registered nosave memory: 00000000db000000 - 00000000db800000
[ 0.000000] PM: Registered nosave memory: 00000000db800000 - 00000000dfa00000
[ 0.000000] PM: Registered nosave memory: 00000000dfa00000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed04000
[ 0.000000] PM: Registered nosave memory: 00000000fed04000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
[ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at dfa00000 (gap:
dfa00000:18600000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512
nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88021f200000 s82304
r8192 d24192 u524288
[ 0.000000] pcpu-alloc: s82304 r8192 d24192 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 2040367
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line:
BOOT_IMAGE=/vmlinuz-3.2.0-0.bpo.2-amd64
root=UUID=118651d8-368b-4b99-b34f-54d30ec810cd ro irqpoll quiet
[ 0.000000] Misrouted IRQ fixup and polling support enabled
[ 0.000000] This may significantly impact system performance
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 8088628k/8902656k available (3517k kernel code,
619452k absent, 194576k reserved, 3216k data, 612k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:33024 nr_irqs:712 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.004000] Detected 3110.150 MHz processor.
[ 0.000001] Calibrating delay loop (skipped), value calculated
using timer frequency.. 6220.30 BogoMIPS (lpj=12440600)
[ 0.000004] pid_max: default: 32768 minimum: 301
[ 0.000031] Security Framework initialized
[ 0.000034] AppArmor: AppArmor disabled by boot time parameter
[ 0.000525] Dentry cache hash table entries: 1048576 (order: 11,
8388608 bytes)
[ 0.001852] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.002408] Mount-cache hash table entries: 256
[ 0.002487] Initializing cgroup subsys cpuacct
[ 0.002490] Initializing cgroup subsys memory
[ 0.002498] Initializing cgroup subsys devices
[ 0.002500] Initializing cgroup subsys freezer
[ 0.002501] Initializing cgroup subsys net_cls
[ 0.002503] Initializing cgroup subsys blkio
[ 0.002507] Initializing cgroup subsys perf_event
[ 0.002527] CPU: Physical Processor ID: 0
[ 0.002528] CPU: Processor Core ID: 0
[ 0.002532] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.002532] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.002534] mce: CPU supports 7 MCE banks
[ 0.002543] CPU0: Thermal monitoring enabled (TM1)
[ 0.002548] using mwait in idle threads.
[ 0.003385] ACPI: Core revision 20110623
[ 0.220687] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.260341] CPU0: Intel(R) Core(TM) i3-2100 CPU @ 3.10GHz stepping 07
[ 0.368106] Performance Events: PEBS fmt1+, SandyBridge events,
Intel PMU driver.
[ 0.368110] PEBS disabled due to CPU errata.
[ 0.368112] ... version: 3
[ 0.368113] ... bit width: 48
[ 0.368113] ... generic registers: 4
[ 0.368114] ... value mask: 0000ffffffffffff
[ 0.368115] ... max period: 000000007fffffff
[ 0.368116] ... fixed-purpose events: 3
[ 0.368117] ... event mask: 000000070000000f
[ 0.368203] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.368272] Booting Node 0, Processors #1
[ 0.368273] smpboot cpu 1: start_ip = 94000
[ 0.476133] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.476206] #2
[ 0.476207] smpboot cpu 2: start_ip = 94000
[ 0.584022] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.584099] #3 Ok.
[ 0.584100] smpboot cpu 3: start_ip = 94000
[ 0.691952] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.691974] Brought up 4 CPUs
[ 0.691976] Total of 4 processors activated (24880.69 BogoMIPS).
[ 0.694444] devtmpfs: initialized
[ 0.696696] PM: Registering ACPI NVS region at da941000 (2379776 bytes)
[ 0.696774] PM: Registering ACPI NVS region at dab94000 (184320 bytes)
[ 0.696781] PM: Registering ACPI NVS region at dabc6000 (274432 bytes)
[ 0.696890] print_constraints: dummy:
[ 0.696932] NET: Registered protocol family 16
[ 0.696997] ACPI FADT declares the system doesn't support PCIe
ASPM, so disable it
[ 0.696999] ACPI: bus type pci registered
[ 0.697049] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem
0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.697051] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.702100] PCI: Using configuration type 1 for base access
[ 0.702613] bio: create slab <bio-0> at 0
[ 0.702678] ACPI: Added _OSI(Module Device)
[ 0.702680] ACPI: Added _OSI(Processor Device)
[ 0.702681] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.702682] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.703769] ACPI: EC: Look up EC in DSDT
[ 0.704809] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.720258] ACPI: SSDT 00000000da8ee018 0083B (v01 PmRef Cpu0Cst
00003001 INTL 20051117)
[ 0.720545] ACPI: Dynamic OEM Table Load:
[ 0.720547] ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst
00003001 INTL 20051117)
[ 0.732102] ACPI: SSDT 00000000da8efa98 00303 (v01 PmRef ApIst
00003000 INTL 20051117)
[ 0.732421] ACPI: Dynamic OEM Table Load:
[ 0.732423] ACPI: SSDT (null) 00303 (v01 PmRef ApIst
00003000 INTL 20051117)
[ 0.743955] ACPI: SSDT 00000000da8f0c18 00119 (v01 PmRef ApCst
00003000 INTL 20051117)
[ 0.744230] ACPI: Dynamic OEM Table Load:
[ 0.744231] ACPI: SSDT (null) 00119 (v01 PmRef ApCst
00003000 INTL 20051117)
[ 0.756403] ACPI: Interpreter enabled
[ 0.756406] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.756428] ACPI: Using IOAPIC for interrupt routing
[ 0.762044] ACPI: Power Resource [FN00] (off)
[ 0.762111] ACPI: Power Resource [FN01] (off)
[ 0.762177] ACPI: Power Resource [FN02] (off)
[ 0.762242] ACPI: Power Resource [FN03] (off)
[ 0.762308] ACPI: Power Resource [FN04] (off)
[ 0.762541] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
[ 0.762712] ACPI: No dock devices found.
[ 0.762713] HEST: Table not found.
[ 0.762716] PCI: Using host bridge windows from ACPI; if necessary,
use "pci=nocrs" and report a bug
[ 0.763000] \_SB_.PCI0:_OSC invalid UUID
[ 0.763001] _OSC request data:1 8 1f
[ 0.763004] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.763463] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.763465] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.763467] pci_root PNP0A08:00: host bridge window [mem
0x000a0000-0x000bffff]
[ 0.763468] pci_root PNP0A08:00: host bridge window [mem
0x000d0000-0x000d3fff]
[ 0.763470] pci_root PNP0A08:00: host bridge window [mem
0x000d4000-0x000d7fff]
[ 0.763471] pci_root PNP0A08:00: host bridge window [mem
0x000d8000-0x000dbfff]
[ 0.763472] pci_root PNP0A08:00: host bridge window [mem
0x000dc000-0x000dffff]
[ 0.763474] pci_root PNP0A08:00: host bridge window [mem
0x000e0000-0x000e3fff]
[ 0.763475] pci_root PNP0A08:00: host bridge window [mem
0x000e4000-0x000e7fff]
[ 0.763477] pci_root PNP0A08:00: host bridge window [mem
0xdfa00000-0xfeafffff]
[ 0.763486] pci 0000:00:00.0: [8086:0100] type 0 class 0x000600
[ 0.763515] pci 0000:00:01.0: [8086:0101] type 1 class 0x000604
[ 0.763538] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.763540] pci 0000:00:01.0: PME# disabled
[ 0.763555] pci 0000:00:02.0: [8086:0102] type 0 class 0x000300
[ 0.763563] pci 0000:00:02.0: reg 10: [mem 0xf7400000-0xf77fffff 64bit]
[ 0.763567] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.763571] pci 0000:00:02.0: reg 20: [io 0xf000-0xf03f]
[ 0.763616] pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
[ 0.763637] pci 0000:00:16.0: reg 10: [mem 0xf7e2c000-0xf7e2c00f 64bit]
[ 0.763708] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.763711] pci 0000:00:16.0: PME# disabled
[ 0.763738] pci 0000:00:19.0: [8086:1503] type 0 class 0x000200
[ 0.763755] pci 0000:00:19.0: reg 10: [mem 0xf7e00000-0xf7e1ffff]
[ 0.763762] pci 0000:00:19.0: reg 14: [mem 0xf7e29000-0xf7e29fff]
[ 0.763770] pci 0000:00:19.0: reg 18: [io 0xf080-0xf09f]
[ 0.763832] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.763835] pci 0000:00:19.0: PME# disabled
[ 0.763858] pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
[ 0.763878] pci 0000:00:1a.0: reg 10: [mem 0xf7e28000-0xf7e283ff]
[ 0.763964] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.763968] pci 0000:00:1a.0: PME# disabled
[ 0.763991] pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
[ 0.764004] pci 0000:00:1b.0: reg 10: [mem 0xf7e20000-0xf7e23fff 64bit]
[ 0.764068] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.764071] pci 0000:00:1b.0: PME# disabled
[ 0.764091] pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
[ 0.764165] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.764169] pci 0000:00:1c.0: PME# disabled
[ 0.764191] pci 0000:00:1c.1: [8086:1c12] type 1 class 0x000604
[ 0.764265] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.764268] pci 0000:00:1c.1: PME# disabled
[ 0.764291] pci 0000:00:1c.3: [8086:1c16] type 1 class 0x000604
[ 0.764365] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.764369] pci 0000:00:1c.3: PME# disabled
[ 0.764391] pci 0000:00:1c.4: [8086:1c18] type 1 class 0x000604
[ 0.764464] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.764468] pci 0000:00:1c.4: PME# disabled
[ 0.764491] pci 0000:00:1c.6: [8086:244e] type 1 class 0x000604
[ 0.764565] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[ 0.764568] pci 0000:00:1c.6: PME# disabled
[ 0.764590] pci 0000:00:1c.7: [8086:1c1e] type 1 class 0x000604
[ 0.764664] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[ 0.764667] pci 0000:00:1c.7: PME# disabled
[ 0.764693] pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
[ 0.764713] pci 0000:00:1d.0: reg 10: [mem 0xf7e27000-0xf7e273ff]
[ 0.764798] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.764802] pci 0000:00:1d.0: PME# disabled
[ 0.764824] pci 0000:00:1f.0: [8086:1c44] type 0 class 0x000601
[ 0.764942] pci 0000:00:1f.2: [8086:1c02] type 0 class 0x000106
[ 0.764959] pci 0000:00:1f.2: reg 10: [io 0xf0d0-0xf0d7]
[ 0.764966] pci 0000:00:1f.2: reg 14: [io 0xf0c0-0xf0c3]
[ 0.764973] pci 0000:00:1f.2: reg 18: [io 0xf0b0-0xf0b7]
[ 0.764980] pci 0000:00:1f.2: reg 1c: [io 0xf0a0-0xf0a3]
[ 0.764987] pci 0000:00:1f.2: reg 20: [io 0xf060-0xf07f]
[ 0.764994] pci 0000:00:1f.2: reg 24: [mem 0xf7e26000-0xf7e267ff]
[ 0.765036] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.765038] pci 0000:00:1f.2: PME# disabled
[ 0.765054] pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
[ 0.765067] pci 0000:00:1f.3: reg 10: [mem 0xf7e25000-0xf7e250ff 64bit]
[ 0.765086] pci 0000:00:1f.3: reg 20: [io 0xf040-0xf05f]
[ 0.765126] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.765169] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.765246] pci 0000:03:00.0: [1b21:1042] type 0 class 0x000c03
[ 0.765274] pci 0000:03:00.0: reg 10: [mem 0xf7d00000-0xf7d07fff 64bit]
[ 0.765418] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.765423] pci 0000:03:00.0: PME# disabled
[ 0.771812] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 0.771821] pci 0000:00:1c.1: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 0.771914] pci 0000:04:00.0: [197b:2362] type 0 class 0x000101
[ 0.771949] pci 0000:04:00.0: reg 10: [io 0xe040-0xe047]
[ 0.771965] pci 0000:04:00.0: reg 14: [io 0xe030-0xe033]
[ 0.771980] pci 0000:04:00.0: reg 18: [io 0xe020-0xe027]
[ 0.771996] pci 0000:04:00.0: reg 1c: [io 0xe010-0xe013]
[ 0.772012] pci 0000:04:00.0: reg 20: [io 0xe000-0xe00f]
[ 0.772027] pci 0000:04:00.0: reg 24: [mem 0xf7c10000-0xf7c101ff]
[ 0.772101] pci 0000:04:00.0: PME# supported from D3hot
[ 0.772107] pci 0000:04:00.0: PME# disabled
[ 0.779804] pci 0000:00:1c.3: PCI bridge to [bus 04-04]
[ 0.779809] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
[ 0.779815] pci 0000:00:1c.3: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.779915] pci 0000:05:00.0: [1b21:1042] type 0 class 0x000c03
[ 0.779943] pci 0000:05:00.0: reg 10: [mem 0xf7b00000-0xf7b07fff 64bit]
[ 0.780088] pci 0000:05:00.0: PME# supported from D3hot D3cold
[ 0.780093] pci 0000:05:00.0: PME# disabled
[ 0.787797] pci 0000:00:1c.4: PCI bridge to [bus 05-05]
[ 0.787805] pci 0000:00:1c.4: bridge window [mem 0xf7b00000-0xf7bfffff]
[ 0.787895] pci 0000:06:00.0: [1b21:1080] type 1 class 0x000604
[ 0.788015] pci 0000:00:1c.6: PCI bridge to [bus 06-07] (subtractive decode)
[ 0.788019] pci 0000:00:1c.6: bridge window [io 0xd000-0xdfff]
[ 0.788023] pci 0000:00:1c.6: bridge window [mem 0xf7800000-0xf79fffff]
[ 0.788029] pci 0000:00:1c.6: bridge window [io 0x0000-0x0cf7]
(subtractive decode)
[ 0.788031] pci 0000:00:1c.6: bridge window [io 0x0d00-0xffff]
(subtractive decode)
[ 0.788032] pci 0000:00:1c.6: bridge window [mem
0x000a0000-0x000bffff] (subtractive decode)
[ 0.788034] pci 0000:00:1c.6: bridge window [mem
0x000d0000-0x000d3fff] (subtractive decode)
[ 0.788035] pci 0000:00:1c.6: bridge window [mem
0x000d4000-0x000d7fff] (subtractive decode)
[ 0.788037] pci 0000:00:1c.6: bridge window [mem
0x000d8000-0x000dbfff] (subtractive decode)
[ 0.788038] pci 0000:00:1c.6: bridge window [mem
0x000dc000-0x000dffff] (subtractive decode)
[ 0.788040] pci 0000:00:1c.6: bridge window [mem
0x000e0000-0x000e3fff] (subtractive decode)
[ 0.788042] pci 0000:00:1c.6: bridge window [mem
0x000e4000-0x000e7fff] (subtractive decode)
[ 0.788043] pci 0000:00:1c.6: bridge window [mem
0xdfa00000-0xfeafffff] (subtractive decode)
[ 0.788102] pci 0000:07:00.0: [1095:3114] type 0 class 0x000104
[ 0.788132] pci 0000:07:00.0: reg 10: [io 0xd110-0xd117]
[ 0.788149] pci 0000:07:00.0: reg 14: [io 0xd100-0xd103]
[ 0.788166] pci 0000:07:00.0: reg 18: [io 0xd0f0-0xd0f7]
[ 0.788183] pci 0000:07:00.0: reg 1c: [io 0xd0e0-0xd0e3]
[ 0.788200] pci 0000:07:00.0: reg 20: [io 0xd0d0-0xd0df]
[ 0.788216] pci 0000:07:00.0: reg 24: [mem 0xf7902000-0xf79023ff]
[ 0.788234] pci 0000:07:00.0: reg 30: [mem 0xf7880000-0xf78fffff pref]
[ 0.788284] pci 0000:07:00.0: supports D1 D2
[ 0.788312] pci 0000:07:01.0: [1095:3114] type 0 class 0x000104
[ 0.788342] pci 0000:07:01.0: reg 10: [io 0xd0c0-0xd0c7]
[ 0.788359] pci 0000:07:01.0: reg 14: [io 0xd0b0-0xd0b3]
[ 0.788375] pci 0000:07:01.0: reg 18: [io 0xd0a0-0xd0a7]
[ 0.788392] pci 0000:07:01.0: reg 1c: [io 0xd090-0xd093]
[ 0.788409] pci 0000:07:01.0: reg 20: [io 0xd080-0xd08f]
[ 0.788426] pci 0000:07:01.0: reg 24: [mem 0xf7901000-0xf79013ff]
[ 0.788443] pci 0000:07:01.0: reg 30: [mem 0xf7800000-0xf787ffff pref]
[ 0.788493] pci 0000:07:01.0: supports D1 D2
[ 0.788522] pci 0000:07:02.0: [1106:3044] type 0 class 0x000c00
[ 0.788552] pci 0000:07:02.0: reg 10: [mem 0xf7900000-0xf79007ff]
[ 0.788570] pci 0000:07:02.0: reg 14: [io 0xd000-0xd07f]
[ 0.788699] pci 0000:07:02.0: supports D2
[ 0.788701] pci 0000:07:02.0: PME# supported from D2 D3hot D3cold
[ 0.788707] pci 0000:07:02.0: PME# disabled
[ 0.788783] pci 0000:06:00.0: PCI bridge to [bus 07-07] (subtractive decode)
[ 0.788792] pci 0000:06:00.0: bridge window [io 0xd000-0xdfff]
[ 0.788798] pci 0000:06:00.0: bridge window [mem 0xf7800000-0xf79fffff]
[ 0.788808] pci 0000:06:00.0: bridge window [io 0xd000-0xdfff]
(subtractive decode)
[ 0.788809] pci 0000:06:00.0: bridge window [mem
0xf7800000-0xf79fffff] (subtractive decode)
[ 0.788811] pci 0000:06:00.0: bridge window [??? 0x00000000 flags
0x0] (subtractive decode)
[ 0.788813] pci 0000:06:00.0: bridge window [??? 0x00000000 flags
0x0] (subtractive decode)
[ 0.788814] pci 0000:06:00.0: bridge window [io 0x0000-0x0cf7]
(subtractive decode)
[ 0.788816] pci 0000:06:00.0: bridge window [io 0x0d00-0xffff]
(subtractive decode)
[ 0.788817] pci 0000:06:00.0: bridge window [mem
0x000a0000-0x000bffff] (subtractive decode)
[ 0.788819] pci 0000:06:00.0: bridge window [mem
0x000d0000-0x000d3fff] (subtractive decode)
[ 0.788821] pci 0000:06:00.0: bridge window [mem
0x000d4000-0x000d7fff] (subtractive decode)
[ 0.788822] pci 0000:06:00.0: bridge window [mem
0x000d8000-0x000dbfff] (subtractive decode)
[ 0.788824] pci 0000:06:00.0: bridge window [mem
0x000dc000-0x000dffff] (subtractive decode)
[ 0.788825] pci 0000:06:00.0: bridge window [mem
0x000e0000-0x000e3fff] (subtractive decode)
[ 0.788827] pci 0000:06:00.0: bridge window [mem
0x000e4000-0x000e7fff] (subtractive decode)
[ 0.788829] pci 0000:06:00.0: bridge window [mem
0xdfa00000-0xfeafffff] (subtractive decode)
[ 0.788900] pci 0000:08:00.0: [1b4b:9172] type 0 class 0x000106
[ 0.788917] pci 0000:08:00.0: reg 10: [io 0xc040-0xc047]
[ 0.788929] pci 0000:08:00.0: reg 14: [io 0xc030-0xc033]
[ 0.788941] pci 0000:08:00.0: reg 18: [io 0xc020-0xc027]
[ 0.788954] pci 0000:08:00.0: reg 1c: [io 0xc010-0xc013]
[ 0.788966] pci 0000:08:00.0: reg 20: [io 0xc000-0xc00f]
[ 0.788978] pci 0000:08:00.0: reg 24: [mem 0xf7a10000-0xf7a101ff]
[ 0.788991] pci 0000:08:00.0: reg 30: [mem 0xf7a00000-0xf7a0ffff pref]
[ 0.789048] pci 0000:08:00.0: PME# supported from D3hot
[ 0.789053] pci 0000:08:00.0: PME# disabled
[ 0.795790] pci 0000:00:1c.7: PCI bridge to [bus 08-08]
[ 0.795795] pci 0000:00:1c.7: bridge window [io 0xc000-0xcfff]
[ 0.795801] pci 0000:00:1c.7: bridge window [mem 0xf7a00000-0xf7afffff]
[ 0.795851] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.796034] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.796068] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.796105] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.796147] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.796183] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP08._PRT]
[ 0.796217] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT]
[ 0.796259] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP07._PRT]
[ 0.796291] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP07.PXSX._PRT]
[ 0.796414] \_SB_.PCI0:_OSC invalid UUID
[ 0.796415] _OSC request data:1 1f 1f
[ 0.796418] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.796462] \_SB_.PCI0:_OSC invalid UUID
[ 0.796462] _OSC request data:1 0 1d
[ 0.796465] pci0000:00: ACPI _OSC request failed (AE_ERROR),
returned control mask: 0x1d
[ 0.796466] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.802038] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.802081] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.802122] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 0.802164] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.802204] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 10 11 12 14 15)
[ 0.802245] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12
14 15) *0, disabled.
[ 0.802285] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 10 11 12 14 15)
[ 0.802326] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.802403] vgaarb: device added:
PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.802412] vgaarb: loaded
[ 0.802413] vgaarb: bridge control possible 0000:00:02.0
[ 0.802438] PCI: Using ACPI for IRQ routing
[ 0.803780] PCI: pci_cache_line_size set to 64 bytes
[ 0.803891] reserve RAM buffer: 0000000000099000 - 000000000009ffff
[ 0.803893] reserve RAM buffer: 00000000da391000 - 00000000dbffffff
[ 0.803896] reserve RAM buffer: 00000000db000000 - 00000000dbffffff
[ 0.803897] reserve RAM buffer: 000000021f600000 - 000000021fffffff
[ 0.803977] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.803981] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.805995] Switching to clocksource hpet
[ 0.807345] pnp: PnP ACPI init
[ 0.807357] ACPI: bus type pnp registered
[ 0.807600] pnp 00:00: [bus 00-3e]
[ 0.807601] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.807603] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.807604] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.807606] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.807607] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.807608] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.807609] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.807611] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.807612] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.807613] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.807615] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.807616] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.807617] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.807619] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.807620] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.807621] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.807622] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.807624] pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
[ 0.807625] pnp 00:00: [mem 0x00010000-0x0001ffff window]
[ 0.807675] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08
PNP0a03 (active)
[ 0.807692] pnp 00:01: [mem 0xfed40000-0xfed44fff]
[ 0.807724] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.807726] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.807735] pnp 00:02: [io 0x0000-0x001f]
[ 0.807737] pnp 00:02: [io 0x0081-0x0091]
[ 0.807738] pnp 00:02: [io 0x0093-0x009f]
[ 0.807739] pnp 00:02: [io 0x00c0-0x00df]
[ 0.807741] pnp 00:02: [dma 4]
[ 0.807756] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.807762] pnp 00:03: [mem 0xff000000-0xffffffff]
[ 0.807806] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.807874] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.807892] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.807901] pnp 00:05: [io 0x002e-0x002f]
[ 0.807902] pnp 00:05: [io 0x004e-0x004f]
[ 0.807903] pnp 00:05: [io 0x0061]
[ 0.807904] pnp 00:05: [io 0x0063]
[ 0.807905] pnp 00:05: [io 0x0065]
[ 0.807906] pnp 00:05: [io 0x0067]
[ 0.807908] pnp 00:05: [io 0x0070]
[ 0.807908] pnp 00:05: [io 0x0080]
[ 0.807909] pnp 00:05: [io 0x0092]
[ 0.807911] pnp 00:05: [io 0x00b2-0x00b3]
[ 0.807912] pnp 00:05: [io 0x0680-0x069f]
[ 0.807913] pnp 00:05: [io 0x0200-0x020f]
[ 0.807914] pnp 00:05: [io 0xffff]
[ 0.807915] pnp 00:05: [io 0xffff]
[ 0.807916] pnp 00:05: [io 0x0400-0x0453]
[ 0.807917] pnp 00:05: [io 0x0458-0x047f]
[ 0.807918] pnp 00:05: [io 0x0500-0x057f]
[ 0.807919] pnp 00:05: [io 0x164e-0x164f]
[ 0.807959] system 00:05: [io 0x0680-0x069f] has been reserved
[ 0.807960] system 00:05: [io 0x0200-0x020f] has been reserved
[ 0.807962] system 00:05: [io 0xffff] has been reserved
[ 0.807964] system 00:05: [io 0xffff] has been reserved
[ 0.807965] system 00:05: [io 0x0400-0x0453] has been reserved
[ 0.807967] system 00:05: [io 0x0458-0x047f] has been reserved
[ 0.807968] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.807970] system 00:05: [io 0x164e-0x164f] has been reserved
[ 0.807972] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.807978] pnp 00:06: [io 0x0070-0x0077]
[ 0.807985] pnp 00:06: [irq 8]
[ 0.808001] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.808024] pnp 00:07: [io 0x0454-0x0457]
[ 0.808053] system 00:07: [io 0x0454-0x0457] has been reserved
[ 0.808055] system 00:07: Plug and Play ACPI device, IDs INT3f0d
PNP0c02 (active)
[ 0.808110] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
[ 0.808111] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
[ 0.808113] pnp 00:08: [io 0x0290-0x029f]
[ 0.808114] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
[ 0.808145] system 00:08: [io 0x0290-0x029f] has been reserved
[ 0.808147] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.808165] pnp 00:09: [io 0x0010-0x001f]
[ 0.808166] pnp 00:09: [io 0x0022-0x003f]
[ 0.808168] pnp 00:09: [io 0x0044-0x005f]
[ 0.808169] pnp 00:09: [io 0x0062-0x0063]
[ 0.808171] pnp 00:09: [io 0x0065-0x006f]
[ 0.808172] pnp 00:09: [io 0x0072-0x007f]
[ 0.808173] pnp 00:09: [io 0x0080]
[ 0.808174] pnp 00:09: [io 0x0084-0x0086]
[ 0.808175] pnp 00:09: [io 0x0088]
[ 0.808176] pnp 00:09: [io 0x008c-0x008e]
[ 0.808177] pnp 00:09: [io 0x0090-0x009f]
[ 0.808178] pnp 00:09: [io 0x00a2-0x00bf]
[ 0.808179] pnp 00:09: [io 0x00e0-0x00ef]
[ 0.808180] pnp 00:09: [io 0x04d0-0x04d1]
[ 0.808217] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.808219] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.808225] pnp 00:0a: [io 0x00f0-0x00ff]
[ 0.808229] pnp 00:0a: [irq 13]
[ 0.808249] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.808479] pnp 00:0b: [mem 0xfed1c000-0xfed1ffff]
[ 0.808480] pnp 00:0b: [mem 0xfed10000-0xfed17fff]
[ 0.808481] pnp 00:0b: [mem 0xfed18000-0xfed18fff]
[ 0.808482] pnp 00:0b: [mem 0xfed19000-0xfed19fff]
[ 0.808484] pnp 00:0b: [mem 0xf8000000-0xfbffffff]
[ 0.808485] pnp 00:0b: [mem 0xfed20000-0xfed3ffff]
[ 0.808486] pnp 00:0b: [mem 0xfed90000-0xfed93fff]
[ 0.808487] pnp 00:0b: [mem 0xfed45000-0xfed8ffff]
[ 0.808488] pnp 00:0b: [mem 0xff000000-0xffffffff]
[ 0.808489] pnp 00:0b: [mem 0xfee00000-0xfeefffff]
[ 0.808491] pnp 00:0b: [mem 0xdfa00000-0xdfa00fff]
[ 0.808541] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.808543] system 00:0b: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.808545] system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.808546] system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.808548] system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.808550] system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.808552] system 00:0b: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.808553] system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.808555] system 00:0b: [mem 0xff000000-0xffffffff] has been reserved
[ 0.808557] system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.808559] system 00:0b: [mem 0xdfa00000-0xdfa00fff] has been reserved
[ 0.808560] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.808684] pnp 00:0c: [mem 0x20000000-0x201fffff]
[ 0.808685] pnp 00:0c: [mem 0x40000000-0x401fffff]
[ 0.808733] system 00:0c: [mem 0x20000000-0x201fffff] has been reserved
[ 0.808734] system 00:0c: [mem 0x40000000-0x401fffff] has been reserved
[ 0.808736] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.808755] pnp: PnP ACPI: found 13 devices
[ 0.808756] ACPI: ACPI bus type pnp unregistered
[ 0.814998] PCI: max bus depth: 2 pci_try_num: 3
[ 0.815063] pci 0000:00:1c.0: BAR 14: assigned [mem 0xdfb00000-0xdfcfffff]
[ 0.815066] pci 0000:00:1c.0: BAR 15: assigned [mem
0xdfd00000-0xdfefffff 64bit pref]
[ 0.815069] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.815070] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.815074] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.815077] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.815082] pci 0000:00:1c.0: bridge window [mem 0xdfb00000-0xdfcfffff]
[ 0.815086] pci 0000:00:1c.0: bridge window [mem
0xdfd00000-0xdfefffff 64bit pref]
[ 0.815091] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 0.815095] pci 0000:00:1c.1: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 0.815103] pci 0000:00:1c.3: PCI bridge to [bus 04-04]
[ 0.815106] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
[ 0.815110] pci 0000:00:1c.3: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.815118] pci 0000:00:1c.4: PCI bridge to [bus 05-05]
[ 0.815122] pci 0000:00:1c.4: bridge window [mem 0xf7b00000-0xf7bfffff]
[ 0.815130] pci 0000:06:00.0: PCI bridge to [bus 07-07]
[ 0.815134] pci 0000:06:00.0: bridge window [io 0xd000-0xdfff]
[ 0.815142] pci 0000:06:00.0: bridge window [mem 0xf7800000-0xf79fffff]
[ 0.815155] pci 0000:00:1c.6: PCI bridge to [bus 06-07]
[ 0.815158] pci 0000:00:1c.6: bridge window [io 0xd000-0xdfff]
[ 0.815162] pci 0000:00:1c.6: bridge window [mem 0xf7800000-0xf79fffff]
[ 0.815170] pci 0000:00:1c.7: PCI bridge to [bus 08-08]
[ 0.815173] pci 0000:00:1c.7: bridge window [io 0xc000-0xcfff]
[ 0.815177] pci 0000:00:1c.7: bridge window [mem 0xf7a00000-0xf7afffff]
[ 0.815193] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.815195] pci 0000:00:01.0: setting latency timer to 64
[ 0.815200] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.815204] pci 0000:00:1c.0: setting latency timer to 64
[ 0.815213] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.815216] pci 0000:00:1c.1: setting latency timer to 64
[ 0.815223] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.815227] pci 0000:00:1c.3: setting latency timer to 64
[ 0.815232] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.815236] pci 0000:00:1c.4: setting latency timer to 64
[ 0.815243] pci 0000:00:1c.6: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.815247] pci 0000:00:1c.6: setting latency timer to 64
[ 0.815253] pci 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.815258] pci 0000:06:00.0: setting latency timer to 64
[ 0.815265] pci 0000:00:1c.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.815268] pci 0000:00:1c.7: setting latency timer to 64
[ 0.815272] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.815273] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.815274] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.815276] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[ 0.815277] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[ 0.815278] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[ 0.815279] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[ 0.815281] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
[ 0.815282] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
[ 0.815283] pci_bus 0000:00: resource 13 [mem 0xdfa00000-0xfeafffff]
[ 0.815285] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.815286] pci_bus 0000:02: resource 1 [mem 0xdfb00000-0xdfcfffff]
[ 0.815288] pci_bus 0000:02: resource 2 [mem 0xdfd00000-0xdfefffff
64bit pref]
[ 0.815289] pci_bus 0000:03: resource 1 [mem 0xf7d00000-0xf7dfffff]
[ 0.815290] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.815292] pci_bus 0000:04: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 0.815293] pci_bus 0000:05: resource 1 [mem 0xf7b00000-0xf7bfffff]
[ 0.815294] pci_bus 0000:06: resource 0 [io 0xd000-0xdfff]
[ 0.815295] pci_bus 0000:06: resource 1 [mem 0xf7800000-0xf79fffff]
[ 0.815297] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7]
[ 0.815298] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff]
[ 0.815299] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.815301] pci_bus 0000:06: resource 7 [mem 0x000d0000-0x000d3fff]
[ 0.815302] pci_bus 0000:06: resource 8 [mem 0x000d4000-0x000d7fff]
[ 0.815303] pci_bus 0000:06: resource 9 [mem 0x000d8000-0x000dbfff]
[ 0.815304] pci_bus 0000:06: resource 10 [mem 0x000dc000-0x000dffff]
[ 0.815306] pci_bus 0000:06: resource 11 [mem 0x000e0000-0x000e3fff]
[ 0.815307] pci_bus 0000:06: resource 12 [mem 0x000e4000-0x000e7fff]
[ 0.815308] pci_bus 0000:06: resource 13 [mem 0xdfa00000-0xfeafffff]
[ 0.815310] pci_bus 0000:07: resource 0 [io 0xd000-0xdfff]
[ 0.815311] pci_bus 0000:07: resource 1 [mem 0xf7800000-0xf79fffff]
[ 0.815312] pci_bus 0000:07: resource 4 [io 0xd000-0xdfff]
[ 0.815313] pci_bus 0000:07: resource 5 [mem 0xf7800000-0xf79fffff]
[ 0.815315] pci_bus 0000:07: resource 8 [io 0x0000-0x0cf7]
[ 0.815316] pci_bus 0000:07: resource 9 [io 0x0d00-0xffff]
[ 0.815317] pci_bus 0000:07: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.815318] pci_bus 0000:07: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.815320] pci_bus 0000:07: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.815321] pci_bus 0000:07: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.815322] pci_bus 0000:07: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.815324] pci_bus 0000:07: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.815325] pci_bus 0000:07: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.815326] pci_bus 0000:07: resource 17 [mem 0xdfa00000-0xfeafffff]
[ 0.815327] pci_bus 0000:08: resource 0 [io 0xc000-0xcfff]
[ 0.815329] pci_bus 0000:08: resource 1 [mem 0xf7a00000-0xf7afffff]
[ 0.815381] NET: Registered protocol family 2
[ 0.815545] IP route cache hash table entries: 262144 (order: 9,
2097152 bytes)
[ 0.816290] TCP established hash table entries: 524288 (order: 11,
8388608 bytes)
[ 0.817300] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.817415] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.817417] TCP reno registered
[ 0.817428] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.817453] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.817550] NET: Registered protocol family 1
[ 0.817962] pci 0000:00:02.0: BIOS left Intel GPU interrupts
enabled; disabling
[ 0.818170] pci 0000:00:02.0: Boot video device
[ 0.818185] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.945896] pci 0000:00:1a.0: PCI INT A disabled
[ 0.945937] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.069798] pci 0000:00:1d.0: PCI INT A disabled
[ 1.069821] pci 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.069872] pci 0000:03:00.0: PCI INT A disabled
[ 1.069886] pci 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.069917] pci 0000:05:00.0: PCI INT A disabled
[ 1.069938] PCI: CLS 64 bytes, default 64
[ 1.069973] Unpacking initramfs...
[ 1.109933] Freeing initrd memory: 2748k freed
[ 1.110190] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.110194] Placing 64MB software IO TLB between ffff8800d6391000 -
ffff8800da391000
[ 1.110195] software IO TLB at phys 0xd6391000 - 0xda391000
[ 1.110583] audit: initializing netlink socket (disabled)
[ 1.110590] type=2000 audit(1343362262.748:1): initialized
[ 1.126988] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.141556] VFS: Disk quotas dquot_6.5.2
[ 1.141580] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.141636] msgmni has been set to 15803
[ 1.141760] alg: No test for stdrng (krng)
[ 1.141785] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 253)
[ 1.141787] io scheduler noop registered
[ 1.141788] io scheduler deadline registered
[ 1.141803] io scheduler cfq registered (default)
[ 1.141873] pcieport 0000:00:01.0: setting latency timer to 64
[ 1.141892] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 1.142135] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.142152] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.142153] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.142484] intel_idle: MWAIT substates: 0x1120
[ 1.142485] intel_idle: v0.4 model 0x2A
[ 1.142486] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.142520] ERST: Table is not found!
[ 1.142521] GHES: HEST is not enabled!
[ 1.142565] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.309938] Linux agpgart interface v0.103
[ 1.309997] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[ 1.310057] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K
total, 262144K mappable
[ 1.310782] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 1.310871] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 1.310957] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.313590] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.313594] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.313696] mousedev: PS/2 mouse device common for all mice
[ 1.313728] rtc_cmos 00:06: RTC can wake from S4
[ 1.313824] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.313849] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.313940] cpuidle: using governor ladder
[ 1.314062] cpuidle: using governor menu
[ 1.314175] TCP cubic registered
[ 1.314256] NET: Registered protocol family 10
[ 1.314632] Mobile IPv6
[ 1.314633] NET: Registered protocol family 17
[ 1.314636] Registering the dns_resolver key type
[ 1.314740] PM: Hibernation image not present or could not be loaded.
[ 1.314748] registered taskstats version 1
[ 1.322426] rtc_cmos 00:06: setting system clock to 2012-07-27
04:11:03 UTC (1343362263)
[ 1.322482] Initializing network drop monitor service
[ 1.323214] Freeing unused kernel memory: 612k freed
[ 1.323273] Write protecting the kernel read-only data: 6144k
[ 1.324587] Freeing unused kernel memory: 560k freed
[ 1.326161] Freeing unused kernel memory: 720k freed
[ 1.334738] udev[56]: starting version 164
[ 1.351366] ACPI: Fan [FAN0] (off)
[ 1.351405] ACPI: Fan [FAN1] (off)
[ 1.351442] ACPI: Fan [FAN2] (off)
[ 1.351481] ACPI: Fan [FAN3] (off)
[ 1.351516] ACPI: Fan [FAN4] (off)
[ 1.355456] SCSI subsystem initialized
[ 1.362502] libata version 3.00 loaded.
[ 1.363106] ahci 0000:00:1f.2: version 3.0
[ 1.363120] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.363169] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 1.373929] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.373931] ACPI: Thermal Zone [TZ00] (28 C)
[ 1.374055] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.374057] ACPI: Thermal Zone [TZ01] (30 C)
[ 1.377715] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6
Gbps 0x7 impl SATA mode
[ 1.377718] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum
part ems apst
[ 1.377722] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.394016] scsi0 : ahci
[ 1.394119] scsi1 : ahci
[ 1.394178] scsi2 : ahci
[ 1.394232] scsi3 : ahci
[ 1.394284] scsi4 : ahci
[ 1.394328] scsi5 : ahci
[ 1.394550] ata1: SATA max UDMA/133 abar m2048@0xf7e26000 port
0xf7e26100 irq 41
[ 1.394553] ata2: SATA max UDMA/133 abar m2048@0xf7e26000 port
0xf7e26180 irq 41
[ 1.394556] ata3: SATA max UDMA/133 abar m2048@0xf7e26000 port
0xf7e26200 irq 41
[ 1.394557] ata4: DUMMY
[ 1.394558] ata5: DUMMY
[ 1.394559] ata6: DUMMY
[ 1.394580] ahci 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.394705] ahci 0000:04:00.0: AHCI 0001.0100 32 slots 2 ports 3
Gbps 0x3 impl SATA mode
[ 1.394708] ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 1.394716] ahci 0000:04:00.0: setting latency timer to 64
[ 1.394930] scsi6 : ahci
[ 1.394977] scsi7 : ahci
[ 1.395033] ata7: SATA max UDMA/133 abar m512@0xf7c10000 port
0xf7c10100 irq 19
[ 1.395037] ata8: SATA max UDMA/133 abar m512@0xf7c10000 port
0xf7c10180 irq 19
[ 1.395054] ahci 0000:08:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.395125] ahci 0000:08:00.0: irq 42 for MSI/MSI-X
[ 1.395179] ahci 0000:08:00.0: AHCI 0001.0000 32 slots 2 ports 6
Gbps 0x3 impl SATA mode
[ 1.395181] ahci 0000:08:00.0: flags: 64bit ncq sntf led only pmp
fbs pio slum part sxs
[ 1.395186] ahci 0000:08:00.0: setting latency timer to 64
[ 1.395377] scsi8 : ahci
[ 1.395423] scsi9 : ahci
[ 1.395455] ata9: SATA max UDMA/133 abar m512@0xf7a10000 port
0xf7a10100 irq 42
[ 1.395458] ata10: SATA max UDMA/133 abar m512@0xf7a10000 port
0xf7a10180 irq 42
[ 1.713416] ata7: SATA link down (SStatus 0 SControl 300)
[ 1.713419] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.713467] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.713477] ata8: SATA link down (SStatus 0 SControl 300)
[ 1.713485] ata10: SATA link down (SStatus 0 SControl 300)
[ 1.713512] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.713972] ACPI Error: [DSSP] Namespace lookup failure,
AE_NOT_FOUND (20110623/psargs-359)
[ 1.713977] ACPI Error: Method parse/execution failed
[\_SB_.PCI0.SAT0.SPT2._GTF] (Node ffff88021649a6f0), AE_NOT_FOUND
(20110623/psparse-536)
[ 1.715065] ACPI Error: [DSSP] Namespace lookup failure,
AE_NOT_FOUND (20110623/psargs-359)
[ 1.715074] ACPI Error: Method parse/execution failed
[\_SB_.PCI0.SAT0.SPT1._GTF] (Node ffff88021649a768), AE_NOT_FOUND
(20110623/psparse-536)
[ 1.715814] ata2.00: ATA-8: WDC WD1002FAEX-00Y9A0, 05.01D05, max UDMA/133
[ 1.715818] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth
31/32), AA
[ 1.717050] ACPI Error: [DSSP] Namespace lookup failure,
AE_NOT_FOUND (20110623/psargs-359)
[ 1.717059] ACPI Error: Method parse/execution failed
[\_SB_.PCI0.SAT0.SPT0._GTF] (Node ffff88021649a7e0), AE_NOT_FOUND
(20110623/psparse-536)
[ 1.717078] ata1.00: ATAPI: HL-DT-ST DVDRAM GH24NS90, IN01, max UDMA/100
[ 1.717518] ACPI Error: [DSSP] Namespace lookup failure,
AE_NOT_FOUND (20110623/psargs-359)
[ 1.717527] ACPI Error: Method parse/execution failed
[\_SB_.PCI0.SAT0.SPT1._GTF] (Node ffff88021649a768), AE_NOT_FOUND
(20110623/psparse-536)
[ 1.717719] ata2.00: configured for UDMA/133
[ 1.723950] ACPI Error: [DSSP] Namespace lookup failure,
AE_NOT_FOUND (20110623/psargs-359)
[ 1.723959] ACPI Error: Method parse/execution failed
[\_SB_.PCI0.SAT0.SPT0._GTF] (Node ffff88021649a7e0), AE_NOT_FOUND
(20110623/psparse-536)
[ 1.723978] ata1.00: configured for UDMA/100
[ 1.736830] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM
GH24NS90 IN01 PQ: 0 ANSI: 5
[ 1.737007] scsi 1:0:0:0: Direct-Access ATA WDC
WD1002FAEX-0 05.0 PQ: 0 ANSI: 5
[ 1.739850] ata3.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 1.739855] ata3.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth
31/32), AA
[ 1.740335] ACPI Error: [DSSP] Namespace lookup failure,
AE_NOT_FOUND (20110623/psargs-359)
[ 1.740343] ACPI Error: Method parse/execution failed
[\_SB_.PCI0.SAT0.SPT2._GTF] (Node ffff88021649a6f0), AE_NOT_FOUND
(20110623/psparse-536)
[ 1.740654] ata3.00: configured for UDMA/133
[ 1.740780] scsi 2:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 1.741914] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks:
(1.00 TB/931 GiB)
[ 1.741946] sd 2:0:0:0: [sdb] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 1.741949] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[ 1.741969] sd 1:0:0:0: [sda] Write Protect is off
[ 1.741971] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.741992] sd 2:0:0:0: [sdb] Write Protect is off
[ 1.741994] sd 1:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.741997] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.742016] sd 2:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.759948] sda: sda1 sda2 sda3
[ 1.760286] sd 1:0:0:0: [sda] Attached SCSI disk
[ 1.761585] sdb: sdb1
[ 1.761878] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 1.885238] ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.898816] ata9.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 1.898821] ata9.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 2.109050] Refined TSC clocksource calibration: 3110.146 MHz.
[ 2.109055] Switching to clocksource tsc
[ 2.133621] ata9.00: configured for UDMA/133
[ 2.133817] scsi 8:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 2.133908] sd 8:0:0:0: [sdc] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 2.133911] sd 8:0:0:0: [sdc] 4096-byte physical blocks
[ 2.133975] sd 8:0:0:0: [sdc] Write Protect is off
[ 2.133977] sd 8:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2.134049] sd 8:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 2.143577] sdc: sdc1
[ 2.143841] sd 8:0:0:0: [sdc] Attached SCSI disk
[ 2.423806] async_tx: api initialized (async)
[ 2.423983] xor: automatically using best checksumming function: generic_sse
[ 2.440758] generic_sse: 13891.000 MB/sec
[ 2.440763] xor: using function: generic_sse (13891.000 MB/sec)
[ 2.508716] raid6: int64x1 3326 MB/s
[ 2.576669] raid6: int64x2 3262 MB/s
[ 2.644609] raid6: int64x4 2993 MB/s
[ 2.712565] raid6: int64x8 2321 MB/s
[ 2.780512] raid6: sse2x1 8388 MB/s
[ 2.848461] raid6: sse2x2 10300 MB/s
[ 2.916407] raid6: sse2x4 11857 MB/s
[ 2.916408] raid6: using algorithm sse2x4 (11857 MB/s)
[ 2.917476] md: raid6 personality registered for level 6
[ 2.917477] md: raid5 personality registered for level 5
[ 2.917479] md: raid4 personality registered for level 4
[ 2.919301] mdadm: sending ioctl 1261 to a partition!
[ 2.919303] mdadm: sending ioctl 1261 to a partition!
[ 2.919866] mdadm: sending ioctl 1261 to a partition!
[ 2.919869] mdadm: sending ioctl 1261 to a partition!
[ 2.927265] mdadm: sending ioctl 1261 to a partition!
[ 2.927269] mdadm: sending ioctl 1261 to a partition!
[ 2.927380] mdadm: sending ioctl 1261 to a partition!
[ 2.927382] mdadm: sending ioctl 1261 to a partition!
[ 2.927479] mdadm: sending ioctl 1261 to a partition!
[ 2.927481] mdadm: sending ioctl 1261 to a partition!
[ 2.986826] kjournald starting. Commit interval 5 seconds
[ 2.986961] EXT3-fs (sda3): mounted filesystem with ordered data mode
[ 3.965497] udev[335]: starting version 164
[ 4.075072] wmi: Mapper loaded
[ 4.171168] input: PC Speaker as /devices/platform/pcspkr/input/input0
[ 4.176232] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 4.176268] ACPI: Power Button [PWRB]
[ 4.176316] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 4.176345] ACPI: Power Button [PWRF]
[ 4.195967] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level,
low) -> IRQ 18
[ 4.195973] ACPI: resource 0000:00:1f.3 [io 0xf040-0xf05f]
conflicts with ACPI region SMBI [io 0xf040-0xf04f]
[ 4.195975] ACPI: If an ACPI driver is available for this device,
you should use it instead of the native driver
[ 4.205863] [drm] Initialized drm 1.1.0 20060810
[ 4.240713] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.240717] i915 0000:00:02.0: setting latency timer to 64
[ 4.246792] asus_wmi: ASUS WMI generic driver loaded
[ 4.247292] asus_wmi: Initialization: 0x0
[ 4.247314] asus_wmi: BIOS WMI version: 0.9
[ 4.247366] asus_wmi: SFUN value: 0x0
[ 4.247730] input: Eee PC WMI hotkeys as
/devices/platform/eeepc-wmi/input/input3
[ 4.248637] asus_wmi: Backlight controlled by ACPI video driver
[ 4.268283] mtrr: type mismatch for e0000000,10000000 old:
write-back new: write-combining
[ 4.268285] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 4.268490] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[ 4.268494] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 4.268495] [drm] Driver supports precise vblank timestamp query.
[ 4.268521] vgaarb: device changed decodes:
PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.302448] e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
[ 4.302449] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 4.357824] firewire_ohci 0000:07:02.0: PCI INT A -> GSI 17 (level,
low) -> IRQ 17
[ 4.367843] usbcore: registered new interface driver usbfs
[ 4.367886] usbcore: registered new interface driver hub
[ 4.367914] usbcore: registered new device driver usb
[ 4.419355] firewire_ohci: Added fw-ohci device 0000:07:02.0, OHCI
v1.10, 4 IR + 8 IT contexts, quirks 0x11
[ 4.426085] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.460049] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 4.460079] xhci_hcd 0000:03:00.0: setting latency timer to 64
[ 4.460084] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 4.460104] xhci_hcd 0000:03:00.0: new USB bus registered, assigned
bus number 1
[ 4.488868] sata_sil 0000:07:00.0: version 2.4
[ 4.488895] sata_sil 0000:07:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.488930] sata_sil 0000:07:00.0: Applying R_ERR on DMA activate
FIS errata fix
[ 4.489348] scsi10 : sata_sil
[ 4.489409] scsi11 : sata_sil
[ 4.489914] scsi12 : sata_sil
[ 4.489967] scsi13 : sata_sil
[ 4.490006] ata11: SATA max UDMA/100 mmio m1024@0xf7902000 tf
0xf7902080 irq 18
[ 4.490013] ata12: SATA max UDMA/100 mmio m1024@0xf7902000 tf
0xf79020c0 irq 18
[ 4.490017] ata13: SATA max UDMA/100 mmio m1024@0xf7902000 tf
0xf7902280 irq 18
[ 4.490022] ata14: SATA max UDMA/100 mmio m1024@0xf7902000 tf
0xf79022c0 irq 18
[ 4.490055] sata_sil 0000:07:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 4.490093] sata_sil 0000:07:01.0: Applying R_ERR on DMA activate
FIS errata fix
[ 4.490507] scsi14 : sata_sil
[ 4.490561] scsi15 : sata_sil
[ 4.490616] scsi16 : sata_sil
[ 4.490663] scsi17 : sata_sil
[ 4.490703] ata15: SATA max UDMA/100 mmio m1024@0xf7901000 tf
0xf7901080 irq 19
[ 4.490708] ata16: SATA max UDMA/100 mmio m1024@0xf7901000 tf
0xf79010c0 irq 19
[ 4.490713] ata17: SATA max UDMA/100 mmio m1024@0xf7901000 tf
0xf7901280 irq 19
[ 4.490718] ata18: SATA max UDMA/100 mmio m1024@0xf7901000 tf
0xf79012c0 irq 19
[ 4.513805] fbcon: inteldrmfb (fb0) is primary device
[ 4.521203] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf7d00000
[ 4.521265] xhci_hcd 0000:03:00.0: irq 44 for MSI/MSI-X
[ 4.521268] xhci_hcd 0000:03:00.0: irq 45 for MSI/MSI-X
[ 4.521271] xhci_hcd 0000:03:00.0: irq 46 for MSI/MSI-X
[ 4.521274] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X
[ 4.521277] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X
[ 4.521370] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.521371] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.521373] usb usb1: Product: xHCI Host Controller
[ 4.521374] usb usb1: Manufacturer: Linux 3.2.0-0.bpo.2-amd64 xhci_hcd
[ 4.521375] usb usb1: SerialNumber: 0000:03:00.0
[ 4.521445] xHCI xhci_add_endpoint called for root hub
[ 4.521446] xHCI xhci_check_bandwidth called for root hub
[ 4.521476] hub 1-0:1.0: USB hub found
[ 4.521484] hub 1-0:1.0: 2 ports detected
[ 4.521541] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 4.521546] xhci_hcd 0000:03:00.0: new USB bus registered, assigned
bus number 2
[ 4.521571] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.521572] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.521574] usb usb2: Product: xHCI Host Controller
[ 4.521575] usb usb2: Manufacturer: Linux 3.2.0-0.bpo.2-amd64 xhci_hcd
[ 4.521577] usb usb2: SerialNumber: 0000:03:00.0
[ 4.521631] xHCI xhci_add_endpoint called for root hub
[ 4.521632] xHCI xhci_check_bandwidth called for root hub
[ 4.521660] hub 2-0:1.0: USB hub found
[ 4.521667] hub 2-0:1.0: 2 ports detected
[ 4.535256] xhci_hcd 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.535288] xhci_hcd 0000:05:00.0: setting latency timer to 64
[ 4.535291] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 4.535298] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 3
[ 4.596398] xhci_hcd 0000:05:00.0: irq 16, io mem 0xf7b00000
[ 4.596491] xhci_hcd 0000:05:00.0: irq 49 for MSI/MSI-X
[ 4.596495] xhci_hcd 0000:05:00.0: irq 50 for MSI/MSI-X
[ 4.596497] xhci_hcd 0000:05:00.0: irq 51 for MSI/MSI-X
[ 4.596500] xhci_hcd 0000:05:00.0: irq 52 for MSI/MSI-X
[ 4.596503] xhci_hcd 0000:05:00.0: irq 53 for MSI/MSI-X
[ 4.596589] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.596591] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.596592] usb usb3: Product: xHCI Host Controller
[ 4.596593] usb usb3: Manufacturer: Linux 3.2.0-0.bpo.2-amd64 xhci_hcd
[ 4.596594] usb usb3: SerialNumber: 0000:05:00.0
[ 4.596675] xHCI xhci_add_endpoint called for root hub
[ 4.596676] xHCI xhci_check_bandwidth called for root hub
[ 4.596696] hub 3-0:1.0: USB hub found
[ 4.596702] hub 3-0:1.0: 2 ports detected
[ 4.596755] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 4.596760] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 4
[ 4.596780] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.596781] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.596782] usb usb4: Product: xHCI Host Controller
[ 4.596783] usb usb4: Manufacturer: Linux 3.2.0-0.bpo.2-amd64 xhci_hcd
[ 4.596784] usb usb4: SerialNumber: 0000:05:00.0
[ 4.596836] xHCI xhci_add_endpoint called for root hub
[ 4.596837] xHCI xhci_check_bandwidth called for root hub
[ 4.596863] hub 4-0:1.0: USB hub found
[ 4.596870] hub 4-0:1.0: 2 ports detected
[ 4.688002] Console: switching to colour frame buffer device 128x48
[ 4.689644] fb0: inteldrmfb frame buffer device
[ 4.689645] drm: registered panic notifier
[ 4.711404] acpi device:63: registered as cooling_device9
[ 4.711556] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 4.711624] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.711676] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.711710] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 4.711720] e1000e 0000:00:19.0: setting latency timer to 64
[ 4.711816] e1000e 0000:00:19.0: irq 54 for MSI/MSI-X
[ 4.807971] ata15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 4.808060] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 4.815920] ata11.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 4.815922] ata11.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.815940] ata15.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 4.815942] ata15.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.847855] ata11.00: configured for UDMA/100
[ 4.847876] ata15.00: configured for UDMA/100
[ 4.847942] scsi 10:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 4.848080] sd 10:0:0:0: [sdd] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 4.848083] sd 10:0:0:0: [sdd] 4096-byte physical blocks
[ 4.848140] sd 10:0:0:0: [sdd] Write Protect is off
[ 4.848142] sd 10:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 4.848160] sd 10:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.871035] sdd: unknown partition table
[ 4.871210] sd 10:0:0:0: [sdd] Attached SCSI disk
[ 4.919032] firewire_core: created device fw0: GUID 001fc600001c5cd1, S400
[ 5.017679] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width
x1) c8:60:00:31:91:20
[ 5.017681] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 5.017730] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
[ 5.017753] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.017785] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 5.017788] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 5.017796] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned
bus number 5
[ 5.017810] ehci_hcd 0000:00:1a.0: broken D3 during system sleep on ASUS
[ 5.017826] ehci_hcd 0000:00:1a.0: debug port 2
[ 5.021703] ehci_hcd 0000:00:1a.0: Enabling legacy PCI PM
[ 5.021711] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 5.021723] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf7e28000
[ 5.034839] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 5.034876] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.034878] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.034879] usb usb5: Product: EHCI Host Controller
[ 5.034880] usb usb5: Manufacturer: Linux 3.2.0-0.bpo.2-amd64 ehci_hcd
[ 5.034881] usb usb5: SerialNumber: 0000:00:1a.0
[ 5.035012] hub 5-0:1.0: USB hub found
[ 5.035016] hub 5-0:1.0: 2 ports detected
[ 5.035070] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 5.035084] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 5.035087] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 5.035093] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 6
[ 5.035105] ehci_hcd 0000:00:1d.0: broken D3 during system sleep on ASUS
[ 5.035118] ehci_hcd 0000:00:1d.0: debug port 2
[ 5.038994] ehci_hcd 0000:00:1d.0: Enabling legacy PCI PM
[ 5.039003] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 5.039019] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf7e27000
[ 5.054825] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 5.054859] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.054861] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.054862] usb usb6: Product: EHCI Host Controller
[ 5.054863] usb usb6: Manufacturer: Linux 3.2.0-0.bpo.2-amd64 ehci_hcd
[ 5.054865] usb usb6: SerialNumber: 0000:00:1d.0
[ 5.054993] hub 6-0:1.0: USB hub found
[ 5.054997] hub 6-0:1.0: 2 ports detected
[ 5.055067] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level,
low) -> IRQ 22
[ 5.055113] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[ 5.055132] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 5.166806] ata12: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 5.175369] ata12.00: ATA-8: ST2000DM001-9YN164, CC4B, max UDMA/133
[ 5.175371] ata12.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 5.215327] ata12.00: configured for UDMA/100
[ 5.215484] scsi 11:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4B PQ: 0 ANSI: 5
[ 5.215587] sd 11:0:0:0: [sde] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 5.215590] sd 11:0:0:0: [sde] 4096-byte physical blocks
[ 5.215665] sd 11:0:0:0: [sde] Write Protect is off
[ 5.215668] sd 11:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 5.215689] sd 11:0:0:0: [sde] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.236677] sde: unknown partition table
[ 5.236838] sd 11:0:0:0: [sde] Attached SCSI disk
[ 5.346609] usb 5-1: new high-speed USB device number 2 using ehci_hcd
[ 5.478953] usb 5-1: New USB device found, idVendor=8087, idProduct=0024
[ 5.478956] usb 5-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.479236] hub 5-1:1.0: USB hub found
[ 5.479324] hub 5-1:1.0: 6 ports detected
[ 5.534544] ata13: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 5.543097] ata13.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 5.543100] ata13.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 5.575058] ata13.00: configured for UDMA/100
[ 5.575204] scsi 12:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 5.575306] sd 12:0:0:0: [sdf] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 5.575309] sd 12:0:0:0: [sdf] 4096-byte physical blocks
[ 5.575347] sd 12:0:0:0: [sdf] Write Protect is off
[ 5.575349] sd 12:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 5.575369] sd 12:0:0:0: [sdf] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.590427] usb 6-1: new high-speed USB device number 2 using ehci_hcd
[ 5.601390] sdf: unknown partition table
[ 5.601550] sd 12:0:0:0: [sdf] Attached SCSI disk
[ 5.722771] usb 6-1: New USB device found, idVendor=8087, idProduct=0024
[ 5.722773] usb 6-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.723060] hub 6-1:1.0: USB hub found
[ 5.723138] hub 6-1:1.0: 8 ports detected
[ 5.794465] usb 5-1.1: new low-speed USB device number 3 using ehci_hcd
[ 5.893392] usb 5-1.1: New USB device found, idVendor=046d, idProduct=c313
[ 5.893394] usb 5-1.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 5.893396] usb 5-1.1: Product: USB Multimedia Keyboard
[ 5.893397] usb 5-1.1: Manufacturer: LITEON Technology
[ 5.894245] ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 5.902831] ata14.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 5.902833] ata14.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 5.934789] ata14.00: configured for UDMA/100
[ 5.934935] scsi 13:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 5.935040] sd 13:0:0:0: [sdg] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 5.935042] sd 13:0:0:0: [sdg] 4096-byte physical blocks
[ 5.935080] sd 13:0:0:0: [sdg] Write Protect is off
[ 5.935082] sd 13:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 5.935098] sd 13:0:0:0: [sdg] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.935163] scsi 14:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 5.935363] sd 14:0:0:0: [sdh] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 5.935366] sd 14:0:0:0: [sdh] 4096-byte physical blocks
[ 5.935415] sd 14:0:0:0: [sdh] Write Protect is off
[ 5.935416] sd 14:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 5.935434] sd 14:0:0:0: [sdh] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.949457] input: LITEON Technology USB Multimedia Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb5/5-1/5-1.1/5-1.1:1.0/input/input5
[ 5.949522] generic-usb 0003:046D:C313.0001: input,hidraw0: USB HID
v1.10 Keyboard [LITEON Technology USB Multimedia Keyboard] on
usb-0000:00:1a.0-1.1/input0
[ 5.952397] input: LITEON Technology USB Multimedia Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb5/5-1/5-1.1/5-1.1:1.1/input/input6
[ 5.952464] generic-usb 0003:046D:C313.0002: input,hidraw1: USB HID
v1.10 Device [LITEON Technology USB Multimedia Keyboard] on
usb-0000:00:1a.0-1.1/input1
[ 5.952474] usbcore: registered new interface driver usbhid
[ 5.952475] usbhid: USB HID core driver
[ 5.954683] sdh: unknown partition table
[ 5.954991] sd 14:0:0:0: [sdh] Attached SCSI disk
[ 5.955691] sdg: unknown partition table
[ 5.955831] sd 13:0:0:0: [sdg] Attached SCSI disk
[ 5.994321] usb 6-1.7: new full-speed USB device number 3 using ehci_hcd
[ 6.086748] usb 6-1.7: New USB device found, idVendor=0cf3, idProduct=3000
[ 6.086751] usb 6-1.7: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 6.253994] ata16: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 6.262558] ata16.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 6.262560] ata16.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 6.294526] ata16.00: configured for UDMA/100
[ 6.294682] scsi 15:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 6.294792] sd 15:0:0:0: [sdi] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 6.294795] sd 15:0:0:0: [sdi] 4096-byte physical blocks
[ 6.294889] sd 15:0:0:0: [sdi] Write Protect is off
[ 6.294891] sd 15:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 6.294968] sd 15:0:0:0: [sdi] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 6.320690] sdi: unknown partition table
[ 6.321017] sd 15:0:0:0: [sdi] Attached SCSI disk
[ 6.613725] ata17: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 6.622290] ata17.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 6.622292] ata17.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 6.662250] ata17.00: configured for UDMA/100
[ 6.662393] scsi 16:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 6.662488] sd 16:0:0:0: [sdj] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 6.662491] sd 16:0:0:0: [sdj] 4096-byte physical blocks
[ 6.662549] sd 16:0:0:0: [sdj] Write Protect is off
[ 6.662551] sd 16:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 6.662626] sd 16:0:0:0: [sdj] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 6.681319] sdj: unknown partition table
[ 6.681471] sd 16:0:0:0: [sdj] Attached SCSI disk
[ 6.981449] ata18: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 6.990018] ata18.00: ATA-8: ST2000DM001-9YN164, CC4C, max UDMA/133
[ 6.990021] ata18.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 7.029978] ata18.00: configured for UDMA/100
[ 7.030096] scsi 17:0:0:0: Direct-Access ATA
ST2000DM001-9YN1 CC4C PQ: 0 ANSI: 5
[ 7.030187] sd 17:0:0:0: [sdk] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 7.030189] sd 17:0:0:0: [sdk] 4096-byte physical blocks
[ 7.030313] sd 17:0:0:0: [sdk] Write Protect is off
[ 7.030316] sd 17:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 7.030393] sd 17:0:0:0: [sdk] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 7.051090] sdk: unknown partition table
[ 7.051410] sd 17:0:0:0: [sdk] Attached SCSI disk
[ 7.066363] sr0: scsi3-mmc drive: 48x/12x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 7.066366] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 7.066492] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 7.138206] HDMI status: Codec=3 Pin=7 Presence_Detect=0 ELD_Valid=0
[ 7.138346] input: HDA Intel PCH HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 7.138506] input: HDA Intel PCH Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 7.171430] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 7.171473] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 7.171513] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 7.171552] sd 8:0:0:0: Attached scsi generic sg3 type 0
[ 7.171595] sd 10:0:0:0: Attached scsi generic sg4 type 0
[ 7.171987] sd 11:0:0:0: Attached scsi generic sg5 type 0
[ 7.172039] sd 12:0:0:0: Attached scsi generic sg6 type 0
[ 7.172138] sd 13:0:0:0: Attached scsi generic sg7 type 0
[ 7.172181] sd 14:0:0:0: Attached scsi generic sg8 type 0
[ 7.172217] sd 15:0:0:0: Attached scsi generic sg9 type 0
[ 7.172255] sd 16:0:0:0: Attached scsi generic sg10 type 0
[ 7.172300] sd 17:0:0:0: Attached scsi generic sg11 type 0
[ 7.217612] Bluetooth: Core ver 2.16
[ 7.217622] NET: Registered protocol family 31
[ 7.217624] Bluetooth: HCI device and connection manager initialized
[ 7.217625] Bluetooth: HCI socket layer initialized
[ 7.217626] Bluetooth: L2CAP socket layer initialized
[ 7.217629] Bluetooth: SCO socket layer initialized
[ 7.261840] Bluetooth: Atheros AR30xx firmware driver ver 1.0
[ 7.449650] Bluetooth: Error loading firmware
[ 7.449683] ath3k: probe of 6-1.7:1.0 failed with error -5
[ 7.449702] usbcore: registered new interface driver ath3k
[ 8.092515] Adding 31250428k swap on /dev/sda2. Priority:-1
extents:1 across:31250428k
[ 8.375202] EXT3-fs (sda3): using internal journal
[ 8.531468] loop: module loaded
[ 8.557506] md: md1 stopped.
[ 8.561218] md: bind<sdf>
[ 8.561443] md: bind<sdg>
[ 8.561669] md: bind<sdj>
[ 8.562104] md: bind<sdk>
[ 8.562248] md: bind<sdc>
[ 8.563795] bio: create slab <bio-1> at 1
[ 8.563802] md/raid:md1: not clean -- starting background reconstruction
[ 8.563812] md/raid:md1: device sdc operational as raid disk 0
[ 8.563814] md/raid:md1: device sdk operational as raid disk 4
[ 8.563815] md/raid:md1: device sdj operational as raid disk 3
[ 8.563817] md/raid:md1: device sdg operational as raid disk 2
[ 8.563819] md/raid:md1: device sdf operational as raid disk 1
[ 8.564244] md/raid:md1: allocated 5332kB
[ 8.565191] md/raid:md1: raid level 6 active with 5 out of 5
devices, algorithm 2
[ 8.565193] RAID conf printout:
[ 8.565195] --- level:6 rd:5 wd:5
[ 8.565196] disk 0, o:1, dev:sdc
[ 8.565198] disk 1, o:1, dev:sdf
[ 8.565200] disk 2, o:1, dev:sdg
[ 8.565201] disk 3, o:1, dev:sdj
[ 8.565203] disk 4, o:1, dev:sdk
[ 8.565238] md1: detected capacity change from 0 to 6001191813120
[ 8.576664] md: md0 stopped.
[ 8.578433] md: bind<sdd>
[ 8.579509] md: bind<sde>
[ 8.579878] md: bind<sdh>
[ 8.580910] md: bind<sdi>
[ 8.581028] md: bind<sdb>
[ 8.581461] md1: unknown partition table
[ 8.584352] md/raid:md0: device sdb operational as raid disk 0
[ 8.584355] md/raid:md0: device sdi operational as raid disk 4
[ 8.584357] md/raid:md0: device sdh operational as raid disk 3
[ 8.584359] md/raid:md0: device sde operational as raid disk 2
[ 8.584361] md/raid:md0: device sdd operational as raid disk 1
[ 8.584795] md/raid:md0: allocated 5332kB
[ 8.584822] md/raid:md0: raid level 6 active with 5 out of 5
devices, algorithm 2
[ 8.584824] RAID conf printout:
[ 8.584825] --- level:6 rd:5 wd:5
[ 8.584826] disk 0, o:1, dev:sdb
[ 8.584827] disk 1, o:1, dev:sdd
[ 8.584828] disk 2, o:1, dev:sde
[ 8.584829] disk 3, o:1, dev:sdh
[ 8.584830] disk 4, o:1, dev:sdi
[ 8.584852] md0: detected capacity change from 0 to 6001191813120
[ 8.587172] md0: unknown partition table
[ 8.926356] kjournald starting. Commit interval 5 seconds
[ 8.926517] EXT3-fs (sda1): using internal journal
[ 8.926520] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 8.975245] SGI XFS with ACLs, security attributes, realtime, large
block/inode numbers, no debug enabled
[ 8.975421] SGI XFS Quota Management subsystem
[ 8.996893] XFS (md0): Mounting Filesystem
[ 9.338163] XFS (md0): Ending clean mount
[ 9.365108] XFS (md1): Mounting Filesystem
[ 9.612625] md: resync of RAID array md1
[ 9.612628] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 9.612630] md: using maximum available idle IO bandwidth (but not
more than 200000 KB/sec) for resync.
[ 9.612634] md: using 128k window, over a total of 1953512960k.
[ 9.612635] md: resuming resync of md1 from checkpoint.
[ 9.774855] XFS (md1): Ending clean mount
[ 10.544176] fuse init (API version 7.17)
[ 11.192332] RPC: Registered named UNIX socket transport module.
[ 11.192334] RPC: Registered udp transport module.
[ 11.192335] RPC: Registered tcp transport module.
[ 11.192336] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.564209] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.611884] svc: failed to register lockdv1 RPC service (errno 97).
[ 11.611909] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state
recovery directory
[ 12.116657] e1000e 0000:00:19.0: irq 54 for MSI/MSI-X
[ 12.169607] e1000e 0000:00:19.0: irq 54 for MSI/MSI-X
[ 12.170093] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.587445] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.587447] Bluetooth: BNEP filters: protocol multicast
[ 13.602250] Bluetooth: RFCOMM TTY layer initialized
[ 13.602254] Bluetooth: RFCOMM socket layer initialized
[ 13.602256] Bluetooth: RFCOMM ver 1.11
[ 13.661202] Bridge firewalling registered
[ 13.727256] e1000e: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow
Control: None
[ 13.727259] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 13.731780] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.402318] lp: driver loaded but no devices found
[ 14.404276] ppdev: user-space parallel port driver
[ 19.322951] sshd (2110): /proc/2110/oom_adj is deprecated, please
use /proc/2110/oom_score_adj instead.
[ 24.244525] eth0: no IPv6 routers present
[ 346.120568] irq 19: nobody cared (try booting with the "irqpoll" option)
[ 346.120572] Pid: 1100, comm: md1_resync Not tainted 3.2.0-0.bpo.2-amd64 #1
[ 346.120573] Call Trace:
[ 346.120575] <IRQ> [<ffffffff8109950b>] ? __report_bad_irq+0x2c/0xb7
[ 346.120582] [<ffffffff8109970e>] ? note_interrupt+0x178/0x1fa
[ 346.120584] [<ffffffff81097aad>] ? handle_irq_event_percpu+0x166/0x184
[ 346.120587] [<ffffffff81024f7f>] ? lapic_next_event+0x18/0x1d
[ 346.120588] [<ffffffff81097aff>] ? handle_irq_event+0x34/0x55
[ 346.120590] [<ffffffff81099d76>] ? handle_fasteoi_irq+0x8d/0xdb
[ 346.120593] [<ffffffff8100fa93>] ? handle_irq+0x1a/0x23
[ 346.120595] [<ffffffff8100f33b>] ? do_IRQ+0x45/0xaa
[ 346.120598] [<ffffffff813655ee>] ? common_interrupt+0x6e/0x6e
[ 346.120601] [<ffffffff811adf9a>] ? blk_done_softirq+0x3e/0x78
[ 346.120604] [<ffffffff8104f1a2>] ? __do_softirq+0xc4/0x1a0
[ 346.120605] [<ffffffff81097aad>] ? handle_irq_event_percpu+0x166/0x184
[ 346.120607] [<ffffffff8104f21b>] ? __do_softirq+0x13d/0x1a0
[ 346.120610] [<ffffffff8136cb6c>] ? call_softirq+0x1c/0x30
[ 346.120612] [<ffffffff8100fa3f>] ? do_softirq+0x3f/0x79
[ 346.120613] [<ffffffff8104ef72>] ? irq_exit+0x44/0xb5
[ 346.120615] [<ffffffff8100f38a>] ? do_IRQ+0x94/0xaa
[ 346.120616] [<ffffffff813655ee>] ? common_interrupt+0x6e/0x6e
[ 346.120617] <EOI> [<ffffffff813652b0>] ?
_raw_spin_unlock_irqrestore+0xb/0x11
[ 346.120638] [<ffffffffa00634b3>] ? ata_scsi_queuecmd+0x65/0x74 [libata]
[ 346.120643] [<ffffffffa001f555>] ? scsi_dispatch_cmd+0x181/0x21c [scsi_mod]
[ 346.120649] [<ffffffffa00247a9>] ? scsi_request_fn+0x338/0x48f [scsi_mod]
[ 346.120651] [<ffffffff811aacb2>] ? blk_queue_bio+0x2ac/0x2ce
[ 346.120653] [<ffffffff811aa026>] ? generic_make_request+0x8e/0xcd
[ 346.120657] [<ffffffffa00e5970>] ? handle_stripe+0x1ab3/0x1bcd [raid456]
[ 346.120661] [<ffffffffa00e622b>] ? sync_request+0x2af/0x1084 [raid456]
[ 346.120666] [<ffffffffa00c26a0>] ? is_mddev_idle+0xb5/0x10b [md_mod]
[ 346.120670] [<ffffffffa00c2e80>] ? md_do_sync+0x78a/0xb98 [md_mod]
[ 346.120673] [<ffffffff8100d65c>] ? __switch_to+0x175/0x2b1
[ 346.120675] [<ffffffff81044620>] ? update_curr+0xbc/0x160
[ 346.120679] [<ffffffffa00c3513>] ? md_thread+0x105/0x123 [md_mod]
[ 346.120683] [<ffffffffa00c340e>] ? md_rdev_init+0xea/0xea [md_mod]
[ 346.120687] [<ffffffffa00c340e>] ? md_rdev_init+0xea/0xea [md_mod]
[ 346.120689] [<ffffffff810633c5>] ? kthread+0x7a/0x82
[ 346.120692] [<ffffffff8136ca74>] ? kernel_thread_helper+0x4/0x10
[ 346.120694] [<ffffffff8106334b>] ? kthread_worker_fn+0x147/0x147
[ 346.120696] [<ffffffff8136ca70>] ? gs_change+0x13/0x13
[ 346.120697] handlers:
[ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
[ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
[ 346.120703] Disabling IRQ #19
[ 346.122145] sched: RT throttling activated
# lsmod
Module Size Used by
acpi_cpufreq 12893 0
mperf 12411 1 acpi_cpufreq
cpufreq_userspace 12576 0
cpufreq_stats 12762 0
cpufreq_conservative 13147 0
cpufreq_powersave 12454 0
parport_pc 22191 0
ppdev 12725 0
lp 17190 0
parport 31650 3 parport_pc,ppdev,lp
bridge 69831 0
stp 12392 1 bridge
rfcomm 32745 0
bnep 17386 2
nfsd 218618 11
lockd 66785 1 nfsd
nfs_acl 12511 1 nfsd
auth_rpcgss 36848 1 nfsd
sunrpc 175670 12 nfsd,lockd,nfs_acl,auth_rpcgss
binfmt_misc 12914 1
fuse 61427 1
xfs 599918 1
loop 22699 0
firewire_sbp2 17741 0
ath3k 12629 0
bluetooth 122093 11 rfcomm,bnep,ath3k
crc16 12343 1 bluetooth
sg 25769 0
snd_hda_codec_hdmi 30578 1
sr_mod 21824 0
usbhid 39946 0
hid 80937 1 usbhid
snd_hda_codec_realtek 188417 1
cdrom 35139 1 sr_mod
xhci_hcd 72574 0
snd_hda_intel 26023 0
snd_hda_codec 81579 3
snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
ehci_hcd 39586 0
usbcore 127444 5 ath3k,usbhid,xhci_hcd,ehci_hcd
snd_hwdep 13148 1 snd_hda_codec
snd_pcm 67465 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
firewire_ohci 35248 0
snd_seq 44678 0
snd_timer 22658 2 snd_pcm,snd_seq
snd_seq_device 13155 1 snd_seq
firewire_core 47887 2 firewire_sbp2,firewire_ohci
snd 52458 9
snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 13014 1 snd
snd_page_alloc 12969 2 snd_hda_intel,snd_pcm
e1000e 128116 0
eeepc_wmi 12564 0
asus_wmi 18670 1 eeepc_wmi
sparse_keymap 12760 1 asus_wmi
i915 357970 2
drm_kms_helper 26950 1 i915
drm 167089 3 i915,drm_kms_helper
rfkill 18970 3 bluetooth,asus_wmi
i2c_i801 16870 0
crc_itu_t 12347 1 firewire_core
i2c_algo_bit 12834 1 i915
usb_common 12354 1 usbcore
i2c_core 23766 5 i915,drm_kms_helper,drm,i2c_i801,i2c_algo_bit
button 12895 1 i915
evdev 17512 12
processor 27588 1 acpi_cpufreq
pcspkr 12579 0
tpm_tis 17315 0
tpm 17841 1 tpm_tis
tpm_bios 12903 1 tpm
video 17553 1 i915
mxm_wmi 12473 0
psmouse 64191 0
serio_raw 12875 0
wmi 13243 2 asus_wmi,mxm_wmi
ext3 160741 2
jbd 55645 1 ext3
mbcache 12930 1 ext3
raid456 51931 1
md_mod 87021 2 raid456
async_raid6_recov 12507 1 raid456
async_pq 12559 2 raid456,async_raid6_recov
raid6_pq 86619 2 async_raid6_recov,async_pq
async_xor 12385 3 raid456,async_raid6_recov,async_pq
xor 12556 1 async_xor
async_memcpy 12350 2 raid456,async_raid6_recov
async_tx 12566 5
raid456,async_raid6_recov,async_pq,async_xor,async_memcpy
sd_mod 35644 9
crc_t10dif 12348 1 sd_mod
ahci 24997 4
libahci 22714 1 ahci
libata 139579 3 sata_sil,ahci,libahci
scsi_mod 161684 5 firewire_sbp2,sg,sr_mod,sd_mod,libata
thermal 17330 0
fan 12674 0
thermal_sys 17992 4 processor,video,thermal,fan
--
Stirling Westrup
Programmer, Entrepreneur.
https://www.linkedin.com/e/fpf/77228
http://www.linkedin.com/in/swestrup
http://technaut.livejournal.com
http://sourceforge.net/users/stirlingwestrup
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-27 16:40 IRQ issues with multiple SiI3114's on Kernel 3.2 Stirling Westrup
@ 2012-07-27 17:24 ` Stan Hoeppner
2012-07-27 22:14 ` Stirling Westrup
0 siblings, 1 reply; 14+ messages in thread
From: Stan Hoeppner @ 2012-07-27 17:24 UTC (permalink / raw)
To: Stirling Westrup; +Cc: linux-ide
On 7/27/2012 11:40 AM, Stirling Westrup wrote:
> I recently purchased a large system for use as a backup server for a
> pair of small businesses. It contains a boot drive plus 10 more
> storage drives. Despite having three onboard SATA controllers, the
> motherboard didn't have enough SATA connectors for all the drives, so
> I installed a pair of identical SiI3114 raid cards to handle the extra
> connections. It has a Sandy Bridge chipset, so I installed a 3.2
> kernel.
>
> # uname -a
> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
> x86_64 GNU/Linux
...
> Okay, enough background. Here's the issue: I had no trouble building
> and sync'ing the first array, but when I try to sync the second array,
> I always get the following dmesg an hour or so into the process:
>
> irq 19: nobody cared (try booting with the "irqpoll" option)
> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
3.2.0-0.bpo.2-amd64 #1
> [ 346.120573] Call Trace:
> ...
> [ 346.120697] handlers:
> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
> [ 346.120703] Disabling IRQ #19
> [ 346.122145] sched: RT throttling activated
...
> From this point onward syncing drops to a tiny fraction of its
> previous speed. I've tried booting with 'irqpoll' as the error message
> suggests, but it has had no effect. I'm really not sure if there is a
> conflict between my two SiI3114's or between the SiI's and the Marvell
> controller (although I've never had an issue with Marvell in the
> past), nor how to go about diagnosing or fixing this. I'll include a
> full dmesg dump below, as well as my currently loaded modules. If
> anyone wants any further info, just ask.
Have you tried irqbalance to spread the interrupts across cores/cache
domains? https://irqbalance.org/documentation.html
Dual/quad socket machines benefit more than a single socket machine, but
the latter can still benefit if the cache hierarchy is appropriate.
~$ aptitude install irqbalance
No guarantees this will fix your problem but it's worth a shot. Takes a
few seconds to install, and it won't cause any negative effects, even if
it yields no positive effects.
--
Stan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-27 17:24 ` Stan Hoeppner
@ 2012-07-27 22:14 ` Stirling Westrup
2012-07-28 2:20 ` Stirling Westrup
0 siblings, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-07-27 22:14 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>
>> I recently purchased a large system for use as a backup server for a
>> pair of small businesses. It contains a boot drive plus 10 more
>> storage drives. Despite having three onboard SATA controllers, the
>> motherboard didn't have enough SATA connectors for all the drives, so
>> I installed a pair of identical SiI3114 raid cards to handle the extra
>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>> kernel.
>>
>> # uname -a
>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>> x86_64 GNU/Linux
> ...
>> Okay, enough background. Here's the issue: I had no trouble building
>> and sync'ing the first array, but when I try to sync the second array,
>> I always get the following dmesg an hour or so into the process:
>>
>> irq 19: nobody cared (try booting with the "irqpoll" option)
>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
> 3.2.0-0.bpo.2-amd64 #1
>> [ 346.120573] Call Trace:
>> ...
>> [ 346.120697] handlers:
>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>> [ 346.120703] Disabling IRQ #19
>> [ 346.122145] sched: RT throttling activated
> ...
>> From this point onward syncing drops to a tiny fraction of its
>> previous speed. I've tried booting with 'irqpoll' as the error message
>> suggests, but it has had no effect. I'm really not sure if there is a
>> conflict between my two SiI3114's or between the SiI's and the Marvell
>> controller (although I've never had an issue with Marvell in the
>> past), nor how to go about diagnosing or fixing this. I'll include a
>> full dmesg dump below, as well as my currently loaded modules. If
>> anyone wants any further info, just ask.
>
> Have you tried irqbalance to spread the interrupts across cores/cache
> domains? https://irqbalance.org/documentation.html
>
Thanks for the tip! I installed irqbalance and rebooted the system,
and everything has been running smoothly for the last two hours. I'll
let everyone know tomorrow if it actually finished the full 20-hour
resync without incidence.
--
Stirling Westrup
Programmer, Entrepreneur.
https://www.linkedin.com/e/fpf/77228
http://www.linkedin.com/in/swestrup
http://technaut.livejournal.com
http://sourceforge.net/users/stirlingwestrup
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-27 22:14 ` Stirling Westrup
@ 2012-07-28 2:20 ` Stirling Westrup
2012-07-28 9:10 ` Stan Hoeppner
0 siblings, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-07-28 2:20 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Fri, Jul 27, 2012 at 6:14 PM, Stirling Westrup <swestrup@gmail.com> wrote:
> On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>>
>>> I recently purchased a large system for use as a backup server for a
>>> pair of small businesses. It contains a boot drive plus 10 more
>>> storage drives. Despite having three onboard SATA controllers, the
>>> motherboard didn't have enough SATA connectors for all the drives, so
>>> I installed a pair of identical SiI3114 raid cards to handle the extra
>>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>>> kernel.
>>>
>>> # uname -a
>>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>>> x86_64 GNU/Linux
>> ...
>>> Okay, enough background. Here's the issue: I had no trouble building
>>> and sync'ing the first array, but when I try to sync the second array,
>>> I always get the following dmesg an hour or so into the process:
>>>
>>> irq 19: nobody cared (try booting with the "irqpoll" option)
>>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
>> 3.2.0-0.bpo.2-amd64 #1
>>> [ 346.120573] Call Trace:
>>> ...
>>> [ 346.120697] handlers:
>>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>>> [ 346.120703] Disabling IRQ #19
>>> [ 346.122145] sched: RT throttling activated
>> ...
>>> From this point onward syncing drops to a tiny fraction of its
>>> previous speed. I've tried booting with 'irqpoll' as the error message
>>> suggests, but it has had no effect. I'm really not sure if there is a
>>> conflict between my two SiI3114's or between the SiI's and the Marvell
>>> controller (although I've never had an issue with Marvell in the
>>> past), nor how to go about diagnosing or fixing this. I'll include a
>>> full dmesg dump below, as well as my currently loaded modules. If
>>> anyone wants any further info, just ask.
>>
>> Have you tried irqbalance to spread the interrupts across cores/cache
>> domains? https://irqbalance.org/documentation.html
>>
>
> Thanks for the tip! I installed irqbalance and rebooted the system,
> and everything has been running smoothly for the last two hours. I'll
> let everyone know tomorrow if it actually finished the full 20-hour
> resync without incidence.
>
>
> --
> Stirling Westrup
> Programmer, Entrepreneur.
> https://www.linkedin.com/e/fpf/77228
> http://www.linkedin.com/in/swestrup
> http://technaut.livejournal.com
> http://sourceforge.net/users/stirlingwestrup
Alas, all it did was delay the IRQ error by a few hours. Does anyone
else have any ideas about how I could tackle this?
--
Stirling Westrup
Programmer, Entrepreneur.
https://www.linkedin.com/e/fpf/77228
http://www.linkedin.com/in/swestrup
http://technaut.livejournal.com
http://sourceforge.net/users/stirlingwestrup
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-28 2:20 ` Stirling Westrup
@ 2012-07-28 9:10 ` Stan Hoeppner
2012-07-28 17:48 ` Stirling Westrup
2012-07-28 18:19 ` Stirling Westrup
0 siblings, 2 replies; 14+ messages in thread
From: Stan Hoeppner @ 2012-07-28 9:10 UTC (permalink / raw)
To: swestrup; +Cc: linux-ide
On 7/27/2012 9:20 PM, Stirling Westrup wrote:
> On Fri, Jul 27, 2012 at 6:14 PM, Stirling Westrup <swestrup@gmail.com> wrote:
>> On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>>> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>>>
>>>> I recently purchased a large system for use as a backup server for a
>>>> pair of small businesses. It contains a boot drive plus 10 more
>>>> storage drives. Despite having three onboard SATA controllers, the
>>>> motherboard didn't have enough SATA connectors for all the drives, so
>>>> I installed a pair of identical SiI3114 raid cards to handle the extra
>>>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>>>> kernel.
>>>>
>>>> # uname -a
>>>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>>>> x86_64 GNU/Linux
>>> ...
>>>> Okay, enough background. Here's the issue: I had no trouble building
>>>> and sync'ing the first array, but when I try to sync the second array,
>>>> I always get the following dmesg an hour or so into the process:
>>>>
>>>> irq 19: nobody cared (try booting with the "irqpoll" option)
>>>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
>>> 3.2.0-0.bpo.2-amd64 #1
>>>> [ 346.120573] Call Trace:
>>>> ...
>>>> [ 346.120697] handlers:
>>>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>>>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>>>> [ 346.120703] Disabling IRQ #19
>>>> [ 346.122145] sched: RT throttling activated
>>> ...
>>>> From this point onward syncing drops to a tiny fraction of its
>>>> previous speed. I've tried booting with 'irqpoll' as the error message
>>>> suggests, but it has had no effect. I'm really not sure if there is a
>>>> conflict between my two SiI3114's or between the SiI's and the Marvell
>>>> controller (although I've never had an issue with Marvell in the
>>>> past), nor how to go about diagnosing or fixing this. I'll include a
>>>> full dmesg dump below, as well as my currently loaded modules. If
>>>> anyone wants any further info, just ask.
>>>
>>> Have you tried irqbalance to spread the interrupts across cores/cache
>>> domains? https://irqbalance.org/documentation.html
>>>
>>
>> Thanks for the tip! I installed irqbalance and rebooted the system,
>> and everything has been running smoothly for the last two hours. I'll
>> let everyone know tomorrow if it actually finished the full 20-hour
>> resync without incidence.
> Alas, all it did was delay the IRQ error by a few hours. Does anyone
> else have any ideas about how I could tackle this?
Try irqpoll and irqbalance together. Also, which motherboard is this,
exact make/model please. May be a BIOS issue. Doesn't seem to be using
MSIs. If the mobo and cards all support MSIs, enabling that may fix
this as well.
Also what make/model are the SiI3114 cards? PCIe or PCI? Have you
tried different slot combinations? Moving one card to a different slot
may get it routed to PCI INTB instead of INTA. That may get it mapped
to something other than IRQ#19. Updating the 3114 boards to their
latest firmware is worth a shot, if not there already.
--
Stan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-28 9:10 ` Stan Hoeppner
@ 2012-07-28 17:48 ` Stirling Westrup
2012-07-28 23:41 ` Stirling Westrup
2012-07-28 18:19 ` Stirling Westrup
1 sibling, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-07-28 17:48 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Sat, Jul 28, 2012 at 5:10 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
> On 7/27/2012 9:20 PM, Stirling Westrup wrote:
>> On Fri, Jul 27, 2012 at 6:14 PM, Stirling Westrup <swestrup@gmail.com> wrote:
>>> On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>>>> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>>>>
>>>>> I recently purchased a large system for use as a backup server for a
>>>>> pair of small businesses. It contains a boot drive plus 10 more
>>>>> storage drives. Despite having three onboard SATA controllers, the
>>>>> motherboard didn't have enough SATA connectors for all the drives, so
>>>>> I installed a pair of identical SiI3114 raid cards to handle the extra
>>>>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>>>>> kernel.
>>>>>
>>>>> # uname -a
>>>>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>>>>> x86_64 GNU/Linux
>>>> ...
>>>>> Okay, enough background. Here's the issue: I had no trouble building
>>>>> and sync'ing the first array, but when I try to sync the second array,
>>>>> I always get the following dmesg an hour or so into the process:
>>>>>
>>>>> irq 19: nobody cared (try booting with the "irqpoll" option)
>>>>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
>>>> 3.2.0-0.bpo.2-amd64 #1
>>>>> [ 346.120573] Call Trace:
>>>>> ...
>>>>> [ 346.120697] handlers:
>>>>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>>>>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>>>>> [ 346.120703] Disabling IRQ #19
>>>>> [ 346.122145] sched: RT throttling activated
>>>> ...
>>>>> From this point onward syncing drops to a tiny fraction of its
>>>>> previous speed. I've tried booting with 'irqpoll' as the error message
>>>>> suggests, but it has had no effect. I'm really not sure if there is a
>>>>> conflict between my two SiI3114's or between the SiI's and the Marvell
>>>>> controller (although I've never had an issue with Marvell in the
>>>>> past), nor how to go about diagnosing or fixing this. I'll include a
>>>>> full dmesg dump below, as well as my currently loaded modules. If
>>>>> anyone wants any further info, just ask.
>>>>
>>>> Have you tried irqbalance to spread the interrupts across cores/cache
>>>> domains? https://irqbalance.org/documentation.html
>>>>
>>>
>>> Thanks for the tip! I installed irqbalance and rebooted the system,
>>> and everything has been running smoothly for the last two hours. I'll
>>> let everyone know tomorrow if it actually finished the full 20-hour
>>> resync without incidence.
>
>> Alas, all it did was delay the IRQ error by a few hours. Does anyone
>> else have any ideas about how I could tackle this?
>
> Try irqpoll and irqbalance together. Also, which motherboard is this,
> exact make/model please. May be a BIOS issue. Doesn't seem to be using
> MSIs. If the mobo and cards all support MSIs, enabling that may fix
> this as well.
>
> Also what make/model are the SiI3114 cards? PCIe or PCI?
The motherboard is an Asus P8768-V Pro/Gen3 and has full MSI support,
but the cards
are labeled "Syba SiI 3114 PCI to 4 Port Sata 150" and don't support MSI.
> Have you
> tried different slot combinations? Moving one card to a different slot
> may get it routed to PCI INTB instead of INTA. That may get it mapped
> to something other than IRQ#19. Updating the 3114 boards to their
> latest firmware is worth a shot, if not there already.
At one point the system was mapping the interrupt to IRQ#17, instead
of 19, but it still failed.
I haven't tried moving the cards to different slots or anything but,
IIRC, it only has two PCI slots.
I also have yet to try upgrading the BIOS of the mobo or updating the
card firmware. I was hoping to have a better
idea of what was going wrong before going down that route.
I also wonder if it the problem could be kernel or libata related.
(which is why I'm asking in this forum).
--
Stirling Westrup
Programmer, Entrepreneur.
https://www.linkedin.com/e/fpf/77228
http://www.linkedin.com/in/swestrup
http://technaut.livejournal.com
http://sourceforge.net/users/stirlingwestrup
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-28 9:10 ` Stan Hoeppner
2012-07-28 17:48 ` Stirling Westrup
@ 2012-07-28 18:19 ` Stirling Westrup
2012-07-28 18:45 ` Stirling Westrup
1 sibling, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-07-28 18:19 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Sat, Jul 28, 2012 at 5:10 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
> On 7/27/2012 9:20 PM, Stirling Westrup wrote:
>> On Fri, Jul 27, 2012 at 6:14 PM, Stirling Westrup <swestrup@gmail.com> wrote:
>>> On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>>>> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>>>>
>>>>> I recently purchased a large system for use as a backup server for a
>>>>> pair of small businesses. It contains a boot drive plus 10 more
>>>>> storage drives. Despite having three onboard SATA controllers, the
>>>>> motherboard didn't have enough SATA connectors for all the drives, so
>>>>> I installed a pair of identical SiI3114 raid cards to handle the extra
>>>>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>>>>> kernel.
>>>>>
>>>>> # uname -a
>>>>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>>>>> x86_64 GNU/Linux
>>>> ...
>>>>> Okay, enough background. Here's the issue: I had no trouble building
>>>>> and sync'ing the first array, but when I try to sync the second array,
>>>>> I always get the following dmesg an hour or so into the process:
>>>>>
>>>>> irq 19: nobody cared (try booting with the "irqpoll" option)
>>>>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
>>>> 3.2.0-0.bpo.2-amd64 #1
>>>>> [ 346.120573] Call Trace:
>>>>> ...
>>>>> [ 346.120697] handlers:
>>>>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>>>>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>>>>> [ 346.120703] Disabling IRQ #19
>>>>> [ 346.122145] sched: RT throttling activated
>>>> ...
>>>>> From this point onward syncing drops to a tiny fraction of its
>>>>> previous speed. I've tried booting with 'irqpoll' as the error message
>>>>> suggests, but it has had no effect. I'm really not sure if there is a
>>>>> conflict between my two SiI3114's or between the SiI's and the Marvell
>>>>> controller (although I've never had an issue with Marvell in the
>>>>> past), nor how to go about diagnosing or fixing this. I'll include a
>>>>> full dmesg dump below, as well as my currently loaded modules. If
>>>>> anyone wants any further info, just ask.
>>>>
>>>> Have you tried irqbalance to spread the interrupts across cores/cache
>>>> domains? https://irqbalance.org/documentation.html
>>>>
>>>
>>> Thanks for the tip! I installed irqbalance and rebooted the system,
>>> and everything has been running smoothly for the last two hours. I'll
>>> let everyone know tomorrow if it actually finished the full 20-hour
>>> resync without incidence.
>
> Try irqpoll and irqbalance together.
Didn't help. In fact, this time the kernel felt it had to disable BOTH
IRQ#19 and then IRQ#17
--
Stirling Westrup
Programmer, Entrepreneur.
https://www.linkedin.com/e/fpf/77228
http://www.linkedin.com/in/swestrup
http://technaut.livejournal.com
http://sourceforge.net/users/stirlingwestrup
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-28 18:19 ` Stirling Westrup
@ 2012-07-28 18:45 ` Stirling Westrup
0 siblings, 0 replies; 14+ messages in thread
From: Stirling Westrup @ 2012-07-28 18:45 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Sat, Jul 28, 2012 at 2:19 PM, Stirling Westrup <swestrup@gmail.com> wrote:
> On Sat, Jul 28, 2012 at 5:10 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>> On 7/27/2012 9:20 PM, Stirling Westrup wrote:
>>> On Fri, Jul 27, 2012 at 6:14 PM, Stirling Westrup <swestrup@gmail.com> wrote:
>>>> On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>>>>> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>>>>>
>>>>>> I recently purchased a large system for use as a backup server for a
>>>>>> pair of small businesses. It contains a boot drive plus 10 more
>>>>>> storage drives. Despite having three onboard SATA controllers, the
>>>>>> motherboard didn't have enough SATA connectors for all the drives, so
>>>>>> I installed a pair of identical SiI3114 raid cards to handle the extra
>>>>>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>>>>>> kernel.
>>>>>>
>>>>>> # uname -a
>>>>>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>>>>>> x86_64 GNU/Linux
>>>>> ...
>>>>>> Okay, enough background. Here's the issue: I had no trouble building
>>>>>> and sync'ing the first array, but when I try to sync the second array,
>>>>>> I always get the following dmesg an hour or so into the process:
>>>>>>
>>>>>> irq 19: nobody cared (try booting with the "irqpoll" option)
>>>>>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
>>>>> 3.2.0-0.bpo.2-amd64 #1
>>>>>> [ 346.120573] Call Trace:
>>>>>> ...
>>>>>> [ 346.120697] handlers:
>>>>>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>>>>>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>>>>>> [ 346.120703] Disabling IRQ #19
>>>>>> [ 346.122145] sched: RT throttling activated
>>>>> ...
>>>>>> From this point onward syncing drops to a tiny fraction of its
>>>>>> previous speed. I've tried booting with 'irqpoll' as the error message
>>>>>> suggests, but it has had no effect. I'm really not sure if there is a
>>>>>> conflict between my two SiI3114's or between the SiI's and the Marvell
>>>>>> controller (although I've never had an issue with Marvell in the
>>>>>> past), nor how to go about diagnosing or fixing this. I'll include a
>>>>>> full dmesg dump below, as well as my currently loaded modules. If
>>>>>> anyone wants any further info, just ask.
>>>>>
>>>>> Have you tried irqbalance to spread the interrupts across cores/cache
>>>>> domains? https://irqbalance.org/documentation.html
>>>>>
>>>>
>>>> Thanks for the tip! I installed irqbalance and rebooted the system,
>>>> and everything has been running smoothly for the last two hours. I'll
>>>> let everyone know tomorrow if it actually finished the full 20-hour
>>>> resync without incidence.
>>
>
>> Try irqpoll and irqbalance together.
>
> Didn't help. In fact, this time the kernel felt it had to disable BOTH
> IRQ#19 and then IRQ#17
>
Actually, looking at my dmesg log from the run with both irqpoll and
irqbalance, I see something very different. I have dozens of errors
reported by ironlake_irq_handler inside i915_irq, which is my graphics
subsystem.
I have no idea if this is a new problem, or another symptom of the old
one. In any case, since the dmesg log is huge, I'll just link to a
pastebin of it:
http://pastebin.com/NmgVVvC2
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-28 17:48 ` Stirling Westrup
@ 2012-07-28 23:41 ` Stirling Westrup
2012-07-29 9:24 ` Stan Hoeppner
0 siblings, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-07-28 23:41 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Sat, Jul 28, 2012 at 1:48 PM, Stirling Westrup <swestrup@gmail.com> wrote:
> On Sat, Jul 28, 2012 at 5:10 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>> On 7/27/2012 9:20 PM, Stirling Westrup wrote:
>>> On Fri, Jul 27, 2012 at 6:14 PM, Stirling Westrup <swestrup@gmail.com> wrote:
>>>> On Fri, Jul 27, 2012 at 1:24 PM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>>>>> On 7/27/2012 11:40 AM, Stirling Westrup wrote:
>>>>>
>>>>>> I recently purchased a large system for use as a backup server for a
>>>>>> pair of small businesses. It contains a boot drive plus 10 more
>>>>>> storage drives. Despite having three onboard SATA controllers, the
>>>>>> motherboard didn't have enough SATA connectors for all the drives, so
>>>>>> I installed a pair of identical SiI3114 raid cards to handle the extra
>>>>>> connections. It has a Sandy Bridge chipset, so I installed a 3.2
>>>>>> kernel.
>>>>>>
>>>>>> # uname -a
>>>>>> Linux ttt 3.2.0-0.bpo.2-amd64 #1 SMP Fri Jun 29 20:42:29 UTC 2012
>>>>>> x86_64 GNU/Linux
>>>>> ...
>>>>>> Okay, enough background. Here's the issue: I had no trouble building
>>>>>> and sync'ing the first array, but when I try to sync the second array,
>>>>>> I always get the following dmesg an hour or so into the process:
>>>>>>
>>>>>> irq 19: nobody cared (try booting with the "irqpoll" option)
>>>>>> [ 346.120572] Pid: 1100, comm: md1_resync Not tainted
>>>>> 3.2.0-0.bpo.2-amd64 #1
>>>>>> [ 346.120573] Call Trace:
>>>>>> ...
>>>>>> [ 346.120697] handlers:
>>>>>> [ 346.120699] [<ffffffffa00479e0>] ahci_interrupt
>>>>>> [ 346.120702] [<ffffffffa02f17ec>] sil_interrupt
>>>>>> [ 346.120703] Disabling IRQ #19
>>>>>> [ 346.122145] sched: RT throttling activated
>>>>> ...
>>>>>> From this point onward syncing drops to a tiny fraction of its
>>>>>> previous speed. I've tried booting with 'irqpoll' as the error message
>>>>>> suggests, but it has had no effect. I'm really not sure if there is a
>>>>>> conflict between my two SiI3114's or between the SiI's and the Marvell
>>>>>> controller (although I've never had an issue with Marvell in the
>>>>>> past), nor how to go about diagnosing or fixing this. I'll include a
>>>>>> full dmesg dump below, as well as my currently loaded modules. If
>>>>>> anyone wants any further info, just ask.
>>>>>
>>>>> Have you tried irqbalance to spread the interrupts across cores/cache
>>>>> domains? https://irqbalance.org/documentation.html
>>>>>
>>>>
>>>> Thanks for the tip! I installed irqbalance and rebooted the system,
>>>> and everything has been running smoothly for the last two hours. I'll
>>>> let everyone know tomorrow if it actually finished the full 20-hour
>>>> resync without incidence.
>>
>>> Alas, all it did was delay the IRQ error by a few hours. Does anyone
>>> else have any ideas about how I could tackle this?
>>
>> Try irqpoll and irqbalance together. Also, which motherboard is this,
>> exact make/model please. May be a BIOS issue. Doesn't seem to be using
>> MSIs. If the mobo and cards all support MSIs, enabling that may fix
>> this as well.
>>
>> Also what make/model are the SiI3114 cards? PCIe or PCI?
>
> The motherboard is an Asus P8768-V Pro/Gen3 and has full MSI support,
> but the cards
> are labeled "Syba SiI 3114 PCI to 4 Port Sata 150" and don't support MSI.
>
>> Have you
>> tried different slot combinations? Moving one card to a different slot
>> may get it routed to PCI INTB instead of INTA. That may get it mapped
>> to something other than IRQ#19. Updating the 3114 boards to their
>> latest firmware is worth a shot, if not there already.
>
> At one point the system was mapping the interrupt to IRQ#17, instead
> of 19, but it still failed.
>
> I haven't tried moving the cards to different slots or anything but,
> IIRC, it only has two PCI slots.
>
> I also have yet to try upgrading the BIOS of the mobo or updating the
> card firmware. I was hoping to have a better
> idea of what was going wrong before going down that route.
>
> I also wonder if it the problem could be kernel or libata related.
> (which is why I'm asking in this forum).
>
Okay, it looks like its a known hardware chipset problem, and was
first reported 6-months ago.
It affects all PCI cards in Asus Sandy-Bridge Motherboards. No known
fix as of yet.
https://lkml.org/lkml/2012/1/30/216
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-28 23:41 ` Stirling Westrup
@ 2012-07-29 9:24 ` Stan Hoeppner
2012-07-29 19:00 ` Stirling Westrup
0 siblings, 1 reply; 14+ messages in thread
From: Stan Hoeppner @ 2012-07-29 9:24 UTC (permalink / raw)
To: swestrup; +Cc: linux-ide
On 7/28/2012 6:41 PM, Stirling Westrup wrote:
> Okay, it looks like its a known hardware chipset problem, and was
> first reported 6-months ago.
>
> It affects all PCI cards in Asus Sandy-Bridge Motherboards. No known
> fix as of yet.
>
> https://lkml.org/lkml/2012/1/30/216
At least our discussion got you looking in multiple directions, one of
which led you to this information.
Given the problem is related to legacy PCI INTx sharing/routing, whether
on the PCI or PCIe bus, I'd recommend you step up to a high quality PCIe
x8 SAS/SATA HBA, such as the LSI 9211-8i PCIe x8, which supports MSI-X
and should instantly solve your problem.
http://www.newegg.com/Product/Product.aspx?Item=N82E16816118112
You'll need two breakout cables:
http://www.newegg.com/Product/Product.aspx?Item=N82E16816116098
This solution will set you back almost $300 USD. I just did some
research on the Syba 4 port SiI 3124 PCIe x1 card. The SiI 3124 is a
native PCI/X chip, thus the board uses a PCI-X to PCIe bridge chip which
hides under the large heatsink. Thus this card will not work, as it
uses legacy PCI interrupts:
http://www.newegg.com/Product/Product.aspx?Item=N82E16816124027
I also looked at the Syba and Adaptec Marvell PCIe x1 SATAII 4 port
cards. While the Marvell chip is native PCIe I'm unable to confirm it
supports MSI/X. And given these cards run $80-90, that's $160-180 for
two of them. The LSI above is pretty much guaranteed to work for ~$100
more. What's your reputation with your client worth?
Speaking of which, don't even look at the $110 8 port Supermicro
SAS/SATA controller. It uses the Marvell SAS chip. Although the chip
itself is fine and works with Windows, the Linux driver *will* eat your
data, all the way up to kernel 3.4. I've personally rectified this
situation for a half dozen users who bought this SM SAS board on price
alone. I converted them all to LSI HBAs and no problems since. The
solution cost them 2-3x as much but they're all happy because it simply
works reliably, and fast.
Or you can start swapping $150+ motherboards until you find one that
works with those $20 Syba 3114 cards. But then you need to ask
yourself, how much is your time worth. You could easily burn 20 or more
hours going that route.
Get the LSI and be done with this.
--
Stan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-29 9:24 ` Stan Hoeppner
@ 2012-07-29 19:00 ` Stirling Westrup
2012-07-29 20:17 ` Stan Hoeppner
2012-08-01 23:43 ` Stirling Westrup
0 siblings, 2 replies; 14+ messages in thread
From: Stirling Westrup @ 2012-07-29 19:00 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Sun, Jul 29, 2012 at 5:24 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
> On 7/28/2012 6:41 PM, Stirling Westrup wrote:
>
>> Okay, it looks like its a known hardware chipset problem, and was
>> first reported 6-months ago.
>>
>> It affects all PCI cards in Asus Sandy-Bridge Motherboards. No known
>> fix as of yet.
>>
>> https://lkml.org/lkml/2012/1/30/216
>
> At least our discussion got you looking in multiple directions, one of
> which led you to this information.
>
> Given the problem is related to legacy PCI INTx sharing/routing, whether
> on the PCI or PCIe bus, I'd recommend you step up to a high quality PCIe
> x8 SAS/SATA HBA, such as the LSI 9211-8i PCIe x8, which supports MSI-X
> and should instantly solve your problem.
> http://www.newegg.com/Product/Product.aspx?Item=N82E16816118112
>
> You'll need two breakout cables:
> http://www.newegg.com/Product/Product.aspx?Item=N82E16816116098
>
> This solution will set you back almost $300 USD. I just did some
> research on the Syba 4 port SiI 3124 PCIe x1 card. The SiI 3124 is a
> native PCI/X chip, thus the board uses a PCI-X to PCIe bridge chip which
> hides under the large heatsink. Thus this card will not work, as it
> uses legacy PCI interrupts:
> http://www.newegg.com/Product/Product.aspx?Item=N82E16816124027
>
> I also looked at the Syba and Adaptec Marvell PCIe x1 SATAII 4 port
> cards. While the Marvell chip is native PCIe I'm unable to confirm it
> supports MSI/X. And given these cards run $80-90, that's $160-180 for
> two of them. The LSI above is pretty much guaranteed to work for ~$100
> more. What's your reputation with your client worth?
>
> Speaking of which, don't even look at the $110 8 port Supermicro
> SAS/SATA controller. It uses the Marvell SAS chip. Although the chip
> itself is fine and works with Windows, the Linux driver *will* eat your
> data, all the way up to kernel 3.4. I've personally rectified this
> situation for a half dozen users who bought this SM SAS board on price
> alone. I converted them all to LSI HBAs and no problems since. The
> solution cost them 2-3x as much but they're all happy because it simply
> works reliably, and fast.
>
> Or you can start swapping $150+ motherboards until you find one that
> works with those $20 Syba 3114 cards. But then you need to ask
> yourself, how much is your time worth. You could easily burn 20 or more
> hours going that route.
>
> Get the LSI and be done with this.
>
The above sounds like excellent advice, and you have saved me several
hours of perusing catalogs trying to figure out what to buy to replace
the two SiI cards. I greatly appreciate the help, and I have sent off
an order to NewEgg for the LSI board and cables.
--
Stirling Westrup
Programmer, Entrepreneur.
https://www.linkedin.com/e/fpf/77228
http://www.linkedin.com/in/swestrup
http://technaut.livejournal.com
http://sourceforge.net/users/stirlingwestrup
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-29 19:00 ` Stirling Westrup
@ 2012-07-29 20:17 ` Stan Hoeppner
2012-08-01 23:43 ` Stirling Westrup
1 sibling, 0 replies; 14+ messages in thread
From: Stan Hoeppner @ 2012-07-29 20:17 UTC (permalink / raw)
To: swestrup; +Cc: linux-ide
On 7/29/2012 2:00 PM, Stirling Westrup wrote:
> On Sun, Jul 29, 2012 at 5:24 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>> On 7/28/2012 6:41 PM, Stirling Westrup wrote:
>>
>>> Okay, it looks like its a known hardware chipset problem, and was
>>> first reported 6-months ago.
>>>
>>> It affects all PCI cards in Asus Sandy-Bridge Motherboards. No known
>>> fix as of yet.
>>>
>>> https://lkml.org/lkml/2012/1/30/216
>>
>> At least our discussion got you looking in multiple directions, one of
>> which led you to this information.
>>
>> Given the problem is related to legacy PCI INTx sharing/routing, whether
>> on the PCI or PCIe bus, I'd recommend you step up to a high quality PCIe
>> x8 SAS/SATA HBA, such as the LSI 9211-8i PCIe x8, which supports MSI-X
>> and should instantly solve your problem.
>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816118112
>>
>> You'll need two breakout cables:
>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816116098
>>
>> This solution will set you back almost $300 USD. I just did some
>> research on the Syba 4 port SiI 3124 PCIe x1 card. The SiI 3124 is a
>> native PCI/X chip, thus the board uses a PCI-X to PCIe bridge chip which
>> hides under the large heatsink. Thus this card will not work, as it
>> uses legacy PCI interrupts:
>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816124027
>>
>> I also looked at the Syba and Adaptec Marvell PCIe x1 SATAII 4 port
>> cards. While the Marvell chip is native PCIe I'm unable to confirm it
>> supports MSI/X. And given these cards run $80-90, that's $160-180 for
>> two of them. The LSI above is pretty much guaranteed to work for ~$100
>> more. What's your reputation with your client worth?
>>
>> Speaking of which, don't even look at the $110 8 port Supermicro
>> SAS/SATA controller. It uses the Marvell SAS chip. Although the chip
>> itself is fine and works with Windows, the Linux driver *will* eat your
>> data, all the way up to kernel 3.4. I've personally rectified this
>> situation for a half dozen users who bought this SM SAS board on price
>> alone. I converted them all to LSI HBAs and no problems since. The
>> solution cost them 2-3x as much but they're all happy because it simply
>> works reliably, and fast.
>>
>> Or you can start swapping $150+ motherboards until you find one that
>> works with those $20 Syba 3114 cards. But then you need to ask
>> yourself, how much is your time worth. You could easily burn 20 or more
>> hours going that route.
>>
>> Get the LSI and be done with this.
>>
>
> The above sounds like excellent advice, and you have saved me several
> hours of perusing catalogs trying to figure out what to buy to replace
> the two SiI cards. I greatly appreciate the help, and I have sent off
> an order to NewEgg for the LSI board and cables.
Always glad to help others with hardware. The 9211-8i comes with RAID
firmware and supports RAID0/1/1E/10. This is not fakeraid, but it's not
really 'true' RAID either as the HBA has no cache, thus it can't sort
writes. Which is why most use this card in JBOD mode as a standard
SAS/SATA HBA with Linux md/RAID. I also recommend using the deadline
elevator, if you're not already.
--
Stan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-07-29 19:00 ` Stirling Westrup
2012-07-29 20:17 ` Stan Hoeppner
@ 2012-08-01 23:43 ` Stirling Westrup
2012-08-02 1:08 ` Stan Hoeppner
1 sibling, 1 reply; 14+ messages in thread
From: Stirling Westrup @ 2012-08-01 23:43 UTC (permalink / raw)
To: stan; +Cc: linux-ide
On Sun, Jul 29, 2012 at 3:00 PM, Stirling Westrup <swestrup@gmail.com> wrote:
> On Sun, Jul 29, 2012 at 5:24 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>> On 7/28/2012 6:41 PM, Stirling Westrup wrote:
>>
>>> Okay, it looks like its a known hardware chipset problem, and was
>>> first reported 6-months ago.
>>>
>>> It affects all PCI cards in Asus Sandy-Bridge Motherboards. No known
>>> fix as of yet.
>>>
>>> https://lkml.org/lkml/2012/1/30/216
>>
>> At least our discussion got you looking in multiple directions, one of
>> which led you to this information.
>>
>> Given the problem is related to legacy PCI INTx sharing/routing, whether
>> on the PCI or PCIe bus, I'd recommend you step up to a high quality PCIe
>> x8 SAS/SATA HBA, such as the LSI 9211-8i PCIe x8, which supports MSI-X
>> and should instantly solve your problem.
>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816118112
>>
>> You'll need two breakout cables:
>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816116098
>>
>> This solution will set you back almost $300 USD. I just did some
>> research on the Syba 4 port SiI 3124 PCIe x1 card. The SiI 3124 is a
>> native PCI/X chip, thus the board uses a PCI-X to PCIe bridge chip which
>> hides under the large heatsink. Thus this card will not work, as it
>> uses legacy PCI interrupts:
>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816124027
>>
>> I also looked at the Syba and Adaptec Marvell PCIe x1 SATAII 4 port
>> cards. While the Marvell chip is native PCIe I'm unable to confirm it
>> supports MSI/X. And given these cards run $80-90, that's $160-180 for
>> two of them. The LSI above is pretty much guaranteed to work for ~$100
>> more. What's your reputation with your client worth?
>>
>> Speaking of which, don't even look at the $110 8 port Supermicro
>> SAS/SATA controller. It uses the Marvell SAS chip. Although the chip
>> itself is fine and works with Windows, the Linux driver *will* eat your
>> data, all the way up to kernel 3.4. I've personally rectified this
>> situation for a half dozen users who bought this SM SAS board on price
>> alone. I converted them all to LSI HBAs and no problems since. The
>> solution cost them 2-3x as much but they're all happy because it simply
>> works reliably, and fast.
>>
>> Or you can start swapping $150+ motherboards until you find one that
>> works with those $20 Syba 3114 cards. But then you need to ask
>> yourself, how much is your time worth. You could easily burn 20 or more
>> hours going that route.
>>
>> Get the LSI and be done with this.
>>
>
> The above sounds like excellent advice, and you have saved me several
> hours of perusing catalogs trying to figure out what to buy to replace
> the two SiI cards. I greatly appreciate the help, and I have sent off
> an order to NewEgg for the LSI board and cables.
>
Just wanted to let everyone know that the new hardware arrived
yesterday, and today my two raid's finished rebuilding without any
problems at all, and at a fair bit higher speed than before.
So, thanks for all your help, in getting my backup system operational.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: IRQ issues with multiple SiI3114's on Kernel 3.2
2012-08-01 23:43 ` Stirling Westrup
@ 2012-08-02 1:08 ` Stan Hoeppner
0 siblings, 0 replies; 14+ messages in thread
From: Stan Hoeppner @ 2012-08-02 1:08 UTC (permalink / raw)
To: swestrup; +Cc: linux-ide
On 8/1/2012 6:43 PM, Stirling Westrup wrote:
> On Sun, Jul 29, 2012 at 3:00 PM, Stirling Westrup <swestrup@gmail.com> wrote:
>> On Sun, Jul 29, 2012 at 5:24 AM, Stan Hoeppner <stan@hardwarefreak.com> wrote:
>>> On 7/28/2012 6:41 PM, Stirling Westrup wrote:
>>>
>>>> Okay, it looks like its a known hardware chipset problem, and was
>>>> first reported 6-months ago.
>>>>
>>>> It affects all PCI cards in Asus Sandy-Bridge Motherboards. No known
>>>> fix as of yet.
>>>>
>>>> https://lkml.org/lkml/2012/1/30/216
>>>
>>> At least our discussion got you looking in multiple directions, one of
>>> which led you to this information.
>>>
>>> Given the problem is related to legacy PCI INTx sharing/routing, whether
>>> on the PCI or PCIe bus, I'd recommend you step up to a high quality PCIe
>>> x8 SAS/SATA HBA, such as the LSI 9211-8i PCIe x8, which supports MSI-X
>>> and should instantly solve your problem.
>>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816118112
>>>
>>> You'll need two breakout cables:
>>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816116098
>>>
>>> This solution will set you back almost $300 USD. I just did some
>>> research on the Syba 4 port SiI 3124 PCIe x1 card. The SiI 3124 is a
>>> native PCI/X chip, thus the board uses a PCI-X to PCIe bridge chip which
>>> hides under the large heatsink. Thus this card will not work, as it
>>> uses legacy PCI interrupts:
>>> http://www.newegg.com/Product/Product.aspx?Item=N82E16816124027
>>>
>>> I also looked at the Syba and Adaptec Marvell PCIe x1 SATAII 4 port
>>> cards. While the Marvell chip is native PCIe I'm unable to confirm it
>>> supports MSI/X. And given these cards run $80-90, that's $160-180 for
>>> two of them. The LSI above is pretty much guaranteed to work for ~$100
>>> more. What's your reputation with your client worth?
>>>
>>> Speaking of which, don't even look at the $110 8 port Supermicro
>>> SAS/SATA controller. It uses the Marvell SAS chip. Although the chip
>>> itself is fine and works with Windows, the Linux driver *will* eat your
>>> data, all the way up to kernel 3.4. I've personally rectified this
>>> situation for a half dozen users who bought this SM SAS board on price
>>> alone. I converted them all to LSI HBAs and no problems since. The
>>> solution cost them 2-3x as much but they're all happy because it simply
>>> works reliably, and fast.
>>>
>>> Or you can start swapping $150+ motherboards until you find one that
>>> works with those $20 Syba 3114 cards. But then you need to ask
>>> yourself, how much is your time worth. You could easily burn 20 or more
>>> hours going that route.
>>>
>>> Get the LSI and be done with this.
>>>
>>
>> The above sounds like excellent advice, and you have saved me several
>> hours of perusing catalogs trying to figure out what to buy to replace
>> the two SiI cards. I greatly appreciate the help, and I have sent off
>> an order to NewEgg for the LSI board and cables.
>>
>
> Just wanted to let everyone know that the new hardware arrived
> yesterday, and today my two raid's finished rebuilding without any
> problems at all, and at a fair bit higher speed than before.
>
> So, thanks for all your help, in getting my backup system operational.
That's great to hear Stirling. Glad it's working well. Coincidentally,
an OP posted today to the LInux-RAID list that he was getting silent
data corruption, again, from his second set of cheapo cards, first Syba,
then Rosewill. I gave him the same advice.
When one spends more on a couple of large pizzas or a case of beer than
on one's disk controller...need I say more?
--
Stan
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2012-08-02 1:08 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-07-27 16:40 IRQ issues with multiple SiI3114's on Kernel 3.2 Stirling Westrup
2012-07-27 17:24 ` Stan Hoeppner
2012-07-27 22:14 ` Stirling Westrup
2012-07-28 2:20 ` Stirling Westrup
2012-07-28 9:10 ` Stan Hoeppner
2012-07-28 17:48 ` Stirling Westrup
2012-07-28 23:41 ` Stirling Westrup
2012-07-29 9:24 ` Stan Hoeppner
2012-07-29 19:00 ` Stirling Westrup
2012-07-29 20:17 ` Stan Hoeppner
2012-08-01 23:43 ` Stirling Westrup
2012-08-02 1:08 ` Stan Hoeppner
2012-07-28 18:19 ` Stirling Westrup
2012-07-28 18:45 ` Stirling Westrup
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.