* [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards
@ 2015-02-22 15:20 Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support Masahiro Yamada
` (9 more replies)
0 siblings, 10 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
Based on Tom's announce mail
(http://lists.denx.de/pipermail/u-boot/2015-February/203606.html),
let's start removing non-generic ARM boards.
No conversion patches have been posted for these boards.
Changes in v4:
- Rebase on commit 4641429695
Changes in v3:
- Do not remove devkit3250 because Vladimir has post a patch
to convert it into Generic Board.
Changes in v2:
- Do not remove armada100 boards because Ajay will send a patch
to convert them.
Masahiro Yamada (9):
ARM: remove mx31ads board support
ARM: mx31: remove imx31_phycore board
ARM: remove jadecpu board support
ARM: remove zmx25 board support
ARM: remove dkb board support
ARM: remove cm4008 and cm41xx board support
ARM: remove a320evb board support
ARM: remove tnetv107x board support
ARM: davinci: remove hawkboard support
arch/arm/Kconfig | 45 --
arch/arm/cpu/arm1176/Makefile | 1 -
arch/arm/cpu/arm1176/start.S | 22 -
arch/arm/cpu/arm1176/tnetv107x/Makefile | 6 -
arch/arm/cpu/arm1176/tnetv107x/aemif.c | 78 ----
arch/arm/cpu/arm1176/tnetv107x/clock.c | 432 ------------------
arch/arm/cpu/arm1176/tnetv107x/init.c | 22 -
arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S | 10 -
arch/arm/cpu/arm1176/tnetv107x/mux.c | 319 -------------
arch/arm/cpu/arm1176/tnetv107x/timer.c | 93 ----
arch/arm/cpu/arm920t/Makefile | 2 -
arch/arm/cpu/arm920t/a320/Makefile | 9 -
arch/arm/cpu/arm920t/a320/reset.S | 10 -
arch/arm/cpu/arm920t/a320/timer.c | 118 -----
arch/arm/cpu/arm920t/ks8695/Makefile | 9 -
arch/arm/cpu/arm920t/ks8695/lowlevel_init.S | 189 --------
arch/arm/cpu/arm920t/ks8695/timer.c | 77 ----
arch/arm/cpu/arm926ejs/Makefile | 2 -
arch/arm/cpu/arm926ejs/mb86r0x/Makefile | 8 -
arch/arm/cpu/arm926ejs/mb86r0x/clock.c | 27 --
arch/arm/cpu/arm926ejs/mb86r0x/reset.c | 24 -
arch/arm/cpu/arm926ejs/mb86r0x/timer.c | 115 -----
arch/arm/cpu/arm926ejs/pantheon/Makefile | 9 -
arch/arm/cpu/arm926ejs/pantheon/cpu.c | 85 ----
arch/arm/cpu/arm926ejs/pantheon/dram.c | 117 -----
arch/arm/cpu/arm926ejs/pantheon/timer.c | 201 ---------
arch/arm/include/asm/arch-a320/a320.h | 22 -
arch/arm/include/asm/arch-ks8695/platform.h | 294 ------------
arch/arm/include/asm/arch-mb86r0x/hardware.h | 15 -
arch/arm/include/asm/arch-mb86r0x/mb86r0x.h | 599 -------------------------
arch/arm/include/asm/arch-pantheon/config.h | 53 ---
arch/arm/include/asm/arch-pantheon/cpu.h | 77 ----
arch/arm/include/asm/arch-pantheon/gpio.h | 0
arch/arm/include/asm/arch-pantheon/mfp.h | 39 --
arch/arm/include/asm/arch-pantheon/pantheon.h | 38 --
arch/arm/include/asm/arch-tnetv107x/clock.h | 53 ---
arch/arm/include/asm/arch-tnetv107x/hardware.h | 160 -------
arch/arm/include/asm/arch-tnetv107x/mux.h | 291 ------------
arch/arm/lib/asm-offsets.c | 46 --
arch/arm/mach-davinci/Kconfig | 4 -
board/Marvell/dkb/Kconfig | 15 -
board/Marvell/dkb/MAINTAINERS | 6 -
board/Marvell/dkb/Makefile | 9 -
board/Marvell/dkb/dkb.c | 85 ----
board/cm4008/Kconfig | 12 -
board/cm4008/MAINTAINERS | 6 -
board/cm4008/Makefile | 8 -
board/cm4008/cm4008.c | 88 ----
board/cm4008/config.mk | 1 -
board/cm4008/flash.c | 395 ----------------
board/cm41xx/Kconfig | 12 -
board/cm41xx/MAINTAINERS | 6 -
board/cm41xx/Makefile | 8 -
board/cm41xx/cm41xx.c | 88 ----
board/cm41xx/config.mk | 1 -
board/cm41xx/flash.c | 395 ----------------
board/davinci/da8xxevm/Kconfig | 13 -
board/davinci/da8xxevm/MAINTAINERS | 8 -
board/davinci/da8xxevm/Makefile | 1 -
board/davinci/da8xxevm/README.hawkboard | 92 ----
board/davinci/da8xxevm/hawkboard-ais-nand.cfg | 4 -
board/davinci/da8xxevm/hawkboard.c | 120 -----
board/davinci/da8xxevm/u-boot-spl-hawk.lds | 69 ---
board/faraday/a320evb/Kconfig | 15 -
board/faraday/a320evb/MAINTAINERS | 6 -
board/faraday/a320evb/Makefile | 9 -
board/faraday/a320evb/a320evb.c | 59 ---
board/faraday/a320evb/lowlevel_init.S | 106 -----
board/freescale/mx31ads/Kconfig | 15 -
board/freescale/mx31ads/MAINTAINERS | 6 -
board/freescale/mx31ads/Makefile | 8 -
board/freescale/mx31ads/lowlevel_init.S | 268 -----------
board/freescale/mx31ads/mx31ads.c | 114 -----
board/freescale/mx31ads/u-boot.lds | 110 -----
board/imx31_phycore/Kconfig | 12 -
board/imx31_phycore/MAINTAINERS | 11 -
board/imx31_phycore/Makefile | 9 -
board/imx31_phycore/imx31_phycore.c | 153 -------
board/imx31_phycore/lowlevel_init.S | 88 ----
board/syteco/jadecpu/Kconfig | 15 -
board/syteco/jadecpu/MAINTAINERS | 6 -
board/syteco/jadecpu/Makefile | 13 -
board/syteco/jadecpu/jadecpu.c | 160 -------
board/syteco/jadecpu/lowlevel_init.S | 249 ----------
board/syteco/zmx25/Kconfig | 15 -
board/syteco/zmx25/MAINTAINERS | 6 -
board/syteco/zmx25/Makefile | 9 -
board/syteco/zmx25/lowlevel_init.S | 97 ----
board/syteco/zmx25/zmx25.c | 174 -------
board/ti/tnetv107xevm/Kconfig | 15 -
board/ti/tnetv107xevm/MAINTAINERS | 6 -
board/ti/tnetv107xevm/Makefile | 5 -
board/ti/tnetv107xevm/config.mk | 5 -
board/ti/tnetv107xevm/sdb_board.c | 134 ------
configs/a320evb_defconfig | 2 -
configs/cm4008_defconfig | 2 -
configs/cm41xx_defconfig | 2 -
configs/dkb_defconfig | 2 -
configs/hawkboard_defconfig | 4 -
configs/hawkboard_uart_defconfig | 5 -
configs/imx31_phycore_defconfig | 2 -
configs/imx31_phycore_eet_defconfig | 3 -
configs/jadecpu_defconfig | 2 -
configs/mx31ads_defconfig | 2 -
configs/tnetv107x_evm_defconfig | 2 -
configs/zmx25_defconfig | 2 -
doc/README.scrapyard | 44 +-
drivers/net/Makefile | 1 -
drivers/net/ks8695eth.c | 229 ----------
drivers/serial/Makefile | 1 -
drivers/serial/serial.c | 2 -
drivers/serial/serial_ks8695.c | 121 -----
drivers/video/Makefile | 1 -
drivers/video/mb86r0xgdc.c | 168 -------
drivers/watchdog/Makefile | 1 -
drivers/watchdog/tnetv107x_wdt.c | 165 -------
include/configs/a320evb.h | 211 ---------
include/configs/cm4008.h | 104 -----
include/configs/cm41xx.h | 104 -----
include/configs/dkb.h | 51 ---
include/configs/hawkboard.h | 220 ---------
include/configs/imx31_phycore.h | 202 ---------
include/configs/jadecpu.h | 273 -----------
include/configs/mx31ads.h | 188 --------
include/configs/tnetv107x_evm.h | 139 ------
include/configs/zmx25.h | 162 -------
include/netdev.h | 1 -
include/serial.h | 3 +-
128 files changed, 28 insertions(+), 9454 deletions(-)
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/Makefile
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/aemif.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/clock.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/init.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/mux.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/timer.c
delete mode 100644 arch/arm/cpu/arm920t/a320/Makefile
delete mode 100644 arch/arm/cpu/arm920t/a320/reset.S
delete mode 100644 arch/arm/cpu/arm920t/a320/timer.c
delete mode 100644 arch/arm/cpu/arm920t/ks8695/Makefile
delete mode 100644 arch/arm/cpu/arm920t/ks8695/lowlevel_init.S
delete mode 100644 arch/arm/cpu/arm920t/ks8695/timer.c
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/Makefile
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/clock.c
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/reset.c
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/timer.c
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
delete mode 100644 arch/arm/include/asm/arch-a320/a320.h
delete mode 100644 arch/arm/include/asm/arch-ks8695/platform.h
delete mode 100644 arch/arm/include/asm/arch-mb86r0x/hardware.h
delete mode 100644 arch/arm/include/asm/arch-mb86r0x/mb86r0x.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/config.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/gpio.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
delete mode 100644 arch/arm/include/asm/arch-tnetv107x/clock.h
delete mode 100644 arch/arm/include/asm/arch-tnetv107x/hardware.h
delete mode 100644 arch/arm/include/asm/arch-tnetv107x/mux.h
delete mode 100644 board/Marvell/dkb/Kconfig
delete mode 100644 board/Marvell/dkb/MAINTAINERS
delete mode 100644 board/Marvell/dkb/Makefile
delete mode 100644 board/Marvell/dkb/dkb.c
delete mode 100644 board/cm4008/Kconfig
delete mode 100644 board/cm4008/MAINTAINERS
delete mode 100644 board/cm4008/Makefile
delete mode 100644 board/cm4008/cm4008.c
delete mode 100644 board/cm4008/config.mk
delete mode 100644 board/cm4008/flash.c
delete mode 100644 board/cm41xx/Kconfig
delete mode 100644 board/cm41xx/MAINTAINERS
delete mode 100644 board/cm41xx/Makefile
delete mode 100644 board/cm41xx/cm41xx.c
delete mode 100644 board/cm41xx/config.mk
delete mode 100644 board/cm41xx/flash.c
delete mode 100644 board/davinci/da8xxevm/README.hawkboard
delete mode 100644 board/davinci/da8xxevm/hawkboard-ais-nand.cfg
delete mode 100644 board/davinci/da8xxevm/hawkboard.c
delete mode 100644 board/davinci/da8xxevm/u-boot-spl-hawk.lds
delete mode 100644 board/faraday/a320evb/Kconfig
delete mode 100644 board/faraday/a320evb/MAINTAINERS
delete mode 100644 board/faraday/a320evb/Makefile
delete mode 100644 board/faraday/a320evb/a320evb.c
delete mode 100644 board/faraday/a320evb/lowlevel_init.S
delete mode 100644 board/freescale/mx31ads/Kconfig
delete mode 100644 board/freescale/mx31ads/MAINTAINERS
delete mode 100644 board/freescale/mx31ads/Makefile
delete mode 100644 board/freescale/mx31ads/lowlevel_init.S
delete mode 100644 board/freescale/mx31ads/mx31ads.c
delete mode 100644 board/freescale/mx31ads/u-boot.lds
delete mode 100644 board/imx31_phycore/Kconfig
delete mode 100644 board/imx31_phycore/MAINTAINERS
delete mode 100644 board/imx31_phycore/Makefile
delete mode 100644 board/imx31_phycore/imx31_phycore.c
delete mode 100644 board/imx31_phycore/lowlevel_init.S
delete mode 100644 board/syteco/jadecpu/Kconfig
delete mode 100644 board/syteco/jadecpu/MAINTAINERS
delete mode 100644 board/syteco/jadecpu/Makefile
delete mode 100644 board/syteco/jadecpu/jadecpu.c
delete mode 100644 board/syteco/jadecpu/lowlevel_init.S
delete mode 100644 board/syteco/zmx25/Kconfig
delete mode 100644 board/syteco/zmx25/MAINTAINERS
delete mode 100644 board/syteco/zmx25/Makefile
delete mode 100644 board/syteco/zmx25/lowlevel_init.S
delete mode 100644 board/syteco/zmx25/zmx25.c
delete mode 100644 board/ti/tnetv107xevm/Kconfig
delete mode 100644 board/ti/tnetv107xevm/MAINTAINERS
delete mode 100644 board/ti/tnetv107xevm/Makefile
delete mode 100644 board/ti/tnetv107xevm/config.mk
delete mode 100644 board/ti/tnetv107xevm/sdb_board.c
delete mode 100644 configs/a320evb_defconfig
delete mode 100644 configs/cm4008_defconfig
delete mode 100644 configs/cm41xx_defconfig
delete mode 100644 configs/dkb_defconfig
delete mode 100644 configs/hawkboard_defconfig
delete mode 100644 configs/hawkboard_uart_defconfig
delete mode 100644 configs/imx31_phycore_defconfig
delete mode 100644 configs/imx31_phycore_eet_defconfig
delete mode 100644 configs/jadecpu_defconfig
delete mode 100644 configs/mx31ads_defconfig
delete mode 100644 configs/tnetv107x_evm_defconfig
delete mode 100644 configs/zmx25_defconfig
delete mode 100644 drivers/net/ks8695eth.c
delete mode 100644 drivers/serial/serial_ks8695.c
delete mode 100644 drivers/video/mb86r0xgdc.c
delete mode 100644 drivers/watchdog/tnetv107x_wdt.c
delete mode 100644 include/configs/a320evb.h
delete mode 100644 include/configs/cm4008.h
delete mode 100644 include/configs/cm41xx.h
delete mode 100644 include/configs/dkb.h
delete mode 100644 include/configs/hawkboard.h
delete mode 100644 include/configs/imx31_phycore.h
delete mode 100644 include/configs/jadecpu.h
delete mode 100644 include/configs/mx31ads.h
delete mode 100644 include/configs/tnetv107x_evm.h
delete mode 100644 include/configs/zmx25.h
--
1.9.1
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-23 22:32 ` Fabio Estevam
2015-02-22 15:20 ` [U-Boot] [PATCH v4 2/9] ARM: mx31: remove imx31_phycore board Masahiro Yamada
` (8 subsequent siblings)
9 siblings, 1 reply; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4:
- Rebase on commit 4641429695
Changes in v3:
- Do not remove devkit3250 because Vladimir has post a patch
to convert it into Generic Board.
Changes in v2:
- Do not remove armada100 boards because Ajay will send a patch
to convert them.
arch/arm/Kconfig | 5 -
board/freescale/mx31ads/Kconfig | 15 --
board/freescale/mx31ads/MAINTAINERS | 6 -
board/freescale/mx31ads/Makefile | 8 -
board/freescale/mx31ads/lowlevel_init.S | 268 --------------------------------
board/freescale/mx31ads/mx31ads.c | 114 --------------
board/freescale/mx31ads/u-boot.lds | 110 -------------
configs/mx31ads_defconfig | 2 -
doc/README.scrapyard | 35 +++--
include/configs/mx31ads.h | 188 ----------------------
10 files changed, 18 insertions(+), 733 deletions(-)
delete mode 100644 board/freescale/mx31ads/Kconfig
delete mode 100644 board/freescale/mx31ads/MAINTAINERS
delete mode 100644 board/freescale/mx31ads/Makefile
delete mode 100644 board/freescale/mx31ads/lowlevel_init.S
delete mode 100644 board/freescale/mx31ads/mx31ads.c
delete mode 100644 board/freescale/mx31ads/u-boot.lds
delete mode 100644 configs/mx31ads_defconfig
delete mode 100644 include/configs/mx31ads.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 820ba1c..7c8b324 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -272,10 +272,6 @@ config TARGET_QONG
bool "Support qong"
select CPU_ARM1136
-config TARGET_MX31ADS
- bool "Support mx31ads"
- select CPU_ARM1136
-
config TARGET_MX31PDK
bool "Support mx31pdk"
select CPU_ARM1136
@@ -797,7 +793,6 @@ source "board/freescale/ls1021atwr/Kconfig"
source "board/freescale/mx23evk/Kconfig"
source "board/freescale/mx25pdk/Kconfig"
source "board/freescale/mx28evk/Kconfig"
-source "board/freescale/mx31ads/Kconfig"
source "board/freescale/mx31pdk/Kconfig"
source "board/freescale/mx35pdk/Kconfig"
source "board/freescale/mx51evk/Kconfig"
diff --git a/board/freescale/mx31ads/Kconfig b/board/freescale/mx31ads/Kconfig
deleted file mode 100644
index eeeb6f4..0000000
--- a/board/freescale/mx31ads/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MX31ADS
-
-config SYS_BOARD
- default "mx31ads"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_SOC
- default "mx31"
-
-config SYS_CONFIG_NAME
- default "mx31ads"
-
-endif
diff --git a/board/freescale/mx31ads/MAINTAINERS b/board/freescale/mx31ads/MAINTAINERS
deleted file mode 100644
index 5f6ec26..0000000
--- a/board/freescale/mx31ads/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MX31ADS BOARD
-#M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
-S: Orphan (since 2013-09)
-F: board/freescale/mx31ads/
-F: include/configs/mx31ads.h
-F: configs/mx31ads_defconfig
diff --git a/board/freescale/mx31ads/Makefile b/board/freescale/mx31ads/Makefile
deleted file mode 100644
index 5e1440d..0000000
--- a/board/freescale/mx31ads/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := mx31ads.o
-obj-y += lowlevel_init.o
diff --git a/board/freescale/mx31ads/lowlevel_init.S b/board/freescale/mx31ads/lowlevel_init.S
deleted file mode 100644
index fcb5549..0000000
--- a/board/freescale/mx31ads/lowlevel_init.S
+++ /dev/null
@@ -1,268 +0,0 @@
-/*
- * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm/arch/imx-regs.h>
-
-.macro REG reg, val
- ldr r2, =\reg
- ldr r3, =\val
- str r3, [r2]
-.endm
-
-.macro REG8 reg, val
- ldr r2, =\reg
- ldr r3, =\val
- strb r3, [r2]
-.endm
-
-.macro DELAY loops
- ldr r2, =\loops
-1:
- subs r2, r2, #1
- nop
- bcs 1b
-.endm
-
-/* RedBoot: AIPS setup - Only setup MPROTx registers.
- * The PACR default values are good.*/
-.macro init_aips
- /*
- * Set all MPROTx to be non-bufferable, trusted for R/W,
- * not forced to user-mode.
- */
- ldr r0, =0x43F00000
- ldr r1, =0x77777777
- str r1, [r0, #0x00]
- str r1, [r0, #0x04]
- ldr r0, =0x53F00000
- str r1, [r0, #0x00]
- str r1, [r0, #0x04]
-
- /*
- * Clear the on and off peripheral modules Supervisor Protect bit
- * for SDMA to access them. Did not change the AIPS control registers
- * (offset 0x20) access type
- */
- ldr r0, =0x43F00000
- ldr r1, =0x0
- str r1, [r0, #0x40]
- str r1, [r0, #0x44]
- str r1, [r0, #0x48]
- str r1, [r0, #0x4C]
- ldr r1, [r0, #0x50]
- and r1, r1, #0x00FFFFFF
- str r1, [r0, #0x50]
-
- ldr r0, =0x53F00000
- ldr r1, =0x0
- str r1, [r0, #0x40]
- str r1, [r0, #0x44]
- str r1, [r0, #0x48]
- str r1, [r0, #0x4C]
- ldr r1, [r0, #0x50]
- and r1, r1, #0x00FFFFFF
- str r1, [r0, #0x50]
-.endm /* init_aips */
-
-/* RedBoot: MAX (Multi-Layer AHB Crossbar Switch) setup */
-.macro init_max
- ldr r0, =0x43F04000
- /* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
- ldr r1, =0x00302154
- str r1, [r0, #0x000] /* for S0 */
- str r1, [r0, #0x100] /* for S1 */
- str r1, [r0, #0x200] /* for S2 */
- str r1, [r0, #0x300] /* for S3 */
- str r1, [r0, #0x400] /* for S4 */
- /* SGPCR - always park on last master */
- ldr r1, =0x10
- str r1, [r0, #0x010] /* for S0 */
- str r1, [r0, #0x110] /* for S1 */
- str r1, [r0, #0x210] /* for S2 */
- str r1, [r0, #0x310] /* for S3 */
- str r1, [r0, #0x410] /* for S4 */
- /* MGPCR - restore default values */
- ldr r1, =0x0
- str r1, [r0, #0x800] /* for M0 */
- str r1, [r0, #0x900] /* for M1 */
- str r1, [r0, #0xA00] /* for M2 */
- str r1, [r0, #0xB00] /* for M3 */
- str r1, [r0, #0xC00] /* for M4 */
- str r1, [r0, #0xD00] /* for M5 */
-.endm /* init_max */
-
-/* RedBoot: M3IF setup */
-.macro init_m3if
- /* Configure M3IF registers */
- ldr r1, =0xB8003000
- /*
- * M3IF Control Register (M3IFCTL)
- * MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000
- * MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000
- * MRRP[2] = MBX not on priority list (0 << 0) = 0x00000000
- * MRRP[3] = MAX1 not on priority list (0 << 0) = 0x00000000
- * MRRP[4] = SDMA not on priority list (0 << 0) = 0x00000000
- * MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000
- * MRRP[6] = IPU1 on priority list (1 << 6) = 0x00000040
- * MRRP[7] = IPU2 not on priority list (0 << 0) = 0x00000000
- * ------------
- * 0x00000040
- */
- ldr r0, =0x00000040
- str r0, [r1] /* M3IF control reg */
-.endm /* init_m3if */
-
-/* RedBoot: To support 133MHz DDR */
-.macro init_drive_strength
- /*
- * Disable maximum drive strength SDRAM/DDR lines by clearing DSE1 bits
- * in SW_PAD_CTL registers
- */
-
- /* SDCLK */
- ldr r1, =0x43FAC200
- ldr r0, [r1, #0x6C]
- bic r0, r0, #(1 << 12)
- str r0, [r1, #0x6C]
-
- /* CAS */
- ldr r0, [r1, #0x70]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x70]
-
- /* RAS */
- ldr r0, [r1, #0x74]
- bic r0, r0, #(1 << 2)
- str r0, [r1, #0x74]
-
- /* CS2 (CSD0) */
- ldr r0, [r1, #0x7C]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x7C]
-
- /* DQM3 */
- ldr r0, [r1, #0x84]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x84]
-
- /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */
- ldr r2, =22 /* (0x2E0 - 0x288) / 4 = 22 */
-pad_loop:
- ldr r0, [r1, #0x88]
- bic r0, r0, #(1 << 22)
- bic r0, r0, #(1 << 12)
- bic r0, r0, #(1 << 2)
- str r0, [r1, #0x88]
- add r1, r1, #4
- subs r2, r2, #0x1
- bne pad_loop
-.endm /* init_drive_strength */
-
-/* CPLD on CS4 setup */
-.macro init_cs4
- ldr r0, =WEIM_BASE
- ldr r1, =0x0000D843
- str r1, [r0, #0x40]
- ldr r1, =0x22252521
- str r1, [r0, #0x44]
- ldr r1, =0x22220A00
- str r1, [r0, #0x48]
-.endm /* init_cs4 */
-
-.globl lowlevel_init
-lowlevel_init:
-
- /* Redboot initializes very early AIPS, what for?
- * Then it also initializes Multi-Layer AHB Crossbar Switch,
- * M3IF */
- /* Also setup the Peripheral Port Remap register inside the core */
- ldr r0, =0x40000015 /* start from AIPS 2GB region */
- mcr p15, 0, r0, c15, c2, 4
-
- init_aips
-
- init_max
-
- init_m3if
-
- init_drive_strength
-
- init_cs4
-
- /* Image Processing Unit: */
- /* Too early to switch display on? */
- REG IPU_CONF, IPU_CONF_DI_EN /* Switch on Display Interface */
- /* Clock Control Module: */
- REG CCM_CCMR, 0x074B0BF5 /* Use CKIH, MCU PLL off */
-
- DELAY 0x40000
-
- REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE /* MCU PLL on */
- REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS /* Switch to MCU PLL */
-
- /* PBC CPLD on CS4 */
- mov r1, #CS4_BASE
- ldrh r1, [r1, #0x2]
- /* Is 27MHz switch set? */
- ands r1, r1, #0x10
-
- /* 532-133-66.5 */
- ldr r0, =CCM_BASE
- ldr r1, =0xFF871D58
- /* PDR0 */
- str r1, [r0, #0x4]
- ldreq r1, MPCTL_PARAM_532
- ldrne r1, MPCTL_PARAM_532_27
- /* MPCTL */
- str r1, [r0, #0x10]
-
- /* Set UPLL=240MHz, USB=60MHz */
- ldr r1, =0x49FCFE7F
- /* PDR1 */
- str r1, [r0, #0x8]
- ldreq r1, UPCTL_PARAM_240
- ldrne r1, UPCTL_PARAM_240_27
- /* UPCTL */
- str r1, [r0, #0x14]
- /* default CLKO to 1/8 of the ARM core */
- mov r1, #0x000002C0
- add r1, r1, #0x00000006
- /* COSR */
- str r1, [r0, #0x1c]
-
- /* RedBoot sets 0x3f, 7, 7, 3, 5, 1, 3, 0 */
-/* REG CCM_PDR0, PDR0_CSI_PODF(0x3f) | PDR0_CSI_PRDF(7) | PDR0_PER_PODF(7) | PDR0_HSP_PODF(2) | PDR0_NFC_PODF(6) | PDR0_IPG_PODF(1) | PDR0_MAX_PODF(2) | PDR0_MCU_PODF(0)*/
-
- /* Redboot: 0, 51, 10, 12 / 0, 14, 9, 13 */
-/* REG CCM_MPCTL, PLL_PD(0) | PLL_MFD(0x33) | PLL_MFI(7) | PLL_MFN(0x23)*/
- /* Default: 1, 4, 12, 1 */
- REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1)
-
- /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */
- REG 0xB8001010, 0x00000004
- REG 0xB8001004, 0x006ac73a
- REG 0xB8001000, 0x92100000
- REG 0x80000f00, 0x12344321
- REG 0xB8001000, 0xa2100000
- REG 0x80000000, 0x12344321
- REG 0x80000000, 0x12344321
- REG 0xB8001000, 0xb2100000
- REG8 0x80000033, 0xda
- REG8 0x81000000, 0xff
- REG 0xB8001000, 0x82226080
- REG 0x80000000, 0xDEADBEEF
- REG 0xB8001010, 0x0000000c
-
- mov pc, lr
-
-MPCTL_PARAM_532:
- .word (((1-1) << 26) + ((52-1) << 16) + (10 << 10) + (12 << 0))
-MPCTL_PARAM_532_27:
- .word (((1-1) << 26) + ((15-1) << 16) + (9 << 10) + (13 << 0))
-UPCTL_PARAM_240:
- .word (((2-1) << 26) + ((13-1) << 16) + (9 << 10) + (3 << 0))
-UPCTL_PARAM_240_27:
- .word (((2-1) << 26) + ((9 -1) << 16) + (8 << 10) + (8 << 0))
diff --git a/board/freescale/mx31ads/mx31ads.c b/board/freescale/mx31ads/mx31ads.c
deleted file mode 100644
index ad89cb0..0000000
--- a/board/freescale/mx31ads/mx31ads.c
+++ /dev/null
@@ -1,114 +0,0 @@
-/*
- * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-int board_early_init_f(void)
-{
- int i;
-
- /* CS0: Nor Flash */
- /*
- * CS0L and CS0A values are from the RedBoot sources by Freescale
- * and are also equal to those used by Sascha Hauer for the Phytec
- * i.MX31 board. CS0U is just a slightly optimized hardware default:
- * the only non-zero field "Wait State Control" is set to half the
- * default value.
- */
- static const struct mxc_weimcs cs0 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 0, 15, 0, 0, 0),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(1, 0, 0, 0, 0, 1, 5, 0, 0, 0, 1, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(0, 0, 7, 2, 0, 0, 2, 1, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(0, &cs0);
-
- /* setup pins for UART1 */
- mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
- mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
- mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
- mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);
-
- /* SPI2 */
- mx31_gpio_mux(MUX_CSPI2_SS2__CSPI2_SS2_B);
- mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
- mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
- mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI);
- mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO);
- mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B);
- mx31_gpio_mux(MUX_CSPI2_SS1__CSPI2_SS1_B);
-
- /* start SPI2 clock */
- __REG(CCM_CGR2) = __REG(CCM_CGR2) | (3 << 4);
-
- /* PBC setup */
- /* Enable UART transceivers also reset the Ethernet/external UART */
- readw(CS4_BASE + 4);
-
- writew(0x8023, CS4_BASE + 4);
-
- /* RedBoot also has an empty loop with 100000 iterations here -
- * clock doesn't run yet */
- for (i = 0; i < 100000; i++)
- ;
-
- /* Clear the reset, toggle the LEDs */
- writew(0xDF, CS4_BASE + 6);
-
- /* clock still doesn't run */
- for (i = 0; i < 100000; i++)
- ;
-
- /* See 1.5.4 in IMX31ADSE_PERI_BUS_CNTRL_CPLD_RM.pdf */
- readb(CS4_BASE + 8);
- readb(CS4_BASE + 7);
- readb(CS4_BASE + 8);
- readb(CS4_BASE + 7);
-
- return 0;
-}
-
-int board_init(void)
-{
- gd->bd->bi_boot_params = 0x80000100; /* adress of boot parameters */
-
- return 0;
-}
-
-int checkboard(void)
-{
- printf("Board: MX31ADS\n");
- return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_CS8900
- rc = cs8900_initialize(0, CONFIG_CS8900_BASE);
-#endif
- return rc;
-}
-#endif
diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds
deleted file mode 100644
index 8a4a8a2..0000000
--- a/board/freescale/mx31ads/u-boot.lds
+++ /dev/null
@@ -1,110 +0,0 @@
-/*
- * January 2004 - Changed to support H4 device
- * Copyright (c) 2004 Texas Instruments
- *
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0x00000000;
-
- . = ALIGN(4);
- .text :
- {
- *(.__image_copy_start)
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- * (.vectors)
- arch/arm/cpu/arm1136/start.o (.text*)
- board/freescale/mx31ads/built-in.o (.text*)
- arch/arm/lib/built-in.o (.text*)
- net/built-in.o (.text*)
- drivers/mtd/built-in.o (.text*)
-
- . = DEFINED(env_offset) ? env_offset : .;
- common/env_embedded.o(.text*)
-
- *(.text*)
- }
- . = ALIGN(4);
- .rodata : { *(.rodata*) }
-
- . = ALIGN(4);
- .data : {
- *(.data*)
- }
-
- . = ALIGN(4);
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = ALIGN(4);
-
- .image_copy_end :
- {
- *(.__image_copy_end)
- }
-
- .rel_dyn_start :
- {
- *(.__rel_dyn_start)
- }
-
- .rel.dyn : {
- *(.rel*)
- }
-
- .rel_dyn_end :
- {
- *(.__rel_dyn_end)
- }
-
- .hash : { *(.hash*) }
-
- .end :
- {
- *(.__end)
- }
-
- _image_binary_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
- .bss_start __rel_dyn_start (OVERLAY) : {
- KEEP(*(.__bss_start));
- __bss_base = .;
- }
-
- .bss __bss_base (OVERLAY) : {
- *(.bss*)
- . = ALIGN(4);
- __bss_limit = .;
- }
- .bss_end __bss_limit (OVERLAY) : {
- KEEP(*(.__bss_end));
- }
-
- .dynsym _image_binary_end : { *(.dynsym) }
- .dynbss : { *(.dynbss) }
- .dynstr : { *(.dynstr*) }
- .dynamic : { *(.dynamic*) }
- .gnu.hash : { *(.gnu.hash) }
- .plt : { *(.plt*) }
- .interp : { *(.interp*) }
- .gnu : { *(.gnu*) }
- .ARM.exidx : { *(.ARM.exidx*) }
-}
diff --git a/configs/mx31ads_defconfig b/configs/mx31ads_defconfig
deleted file mode 100644
index 5105a9a..0000000
--- a/configs/mx31ads_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_MX31ADS=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 952ab87..c6f3d14 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,23 +12,24 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-icecube_5200 powerpc mpc5xxx - - Wolfgang Denk <wd@denx.de>
-Lite5200 powerpc mpc5xxx - -
-cpci5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-mecp5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-pf5200 powerpc mpc5xxx - - Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-PM520 powerpc mpc5xxx - - Josef Wagner <Wagner@Microsys.de>
-Total5200 powerpc mpc5xxx - -
-CATcenter powerpc ppc4xx - -
-PPChameleonEVB powerpc ppc4xx - - Andrea "llandre" Marson <andrea.marson@dave-tech.it>
-P2020DS powerpc mpc85xx - -
-P2020COME powerpc mpc85xx - - Ira W. Snyder <iws@ovro.caltech.edu>
-P2020RDB powerpc mpc85xx - - Poonam Aggrwal <poonam.aggrwal@freescale.com>
-P2010RDB powerpc mpc85xx - -
-P1020RDB powerpc mpc85xx - -
-P1011RDB powerpc mpc85xx - -
-MPC8360EMDS powerpc mpc83xx - - Dave Liu <daveliu@freescale.com>
-MPC8360ERDK powerpc mpc83xx - - Anton Vorontsov <avorontsov@ru.mvista.com>
+mx31ads arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
+icecube_5200 powerpc mpc5xxx 37b608a5 2015-01-23 Wolfgang Denk <wd@denx.de>
+Lite5200 powerpc mpc5xxx 37b608a5 2015-01-23
+cpci5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+mecp5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+pf5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+PM520 powerpc mpc5xxx a258e732 2015-01-23 Josef Wagner <Wagner@Microsys.de>
+Total5200 powerpc mpc5xxx ad734f7d 2015-01-23
+CATcenter powerpc ppc4xx 5344cc1a 2015-01-23
+PPChameleonEVB powerpc ppc4xx 5344cc1a 2015-01-23 Andrea "llandre" Marson <andrea.marson@dave-tech.it>
+P2020DS powerpc mpc85xx 168dcc6c 2015-01-23
+P2020COME powerpc mpc85xx 89123536 2015-01-23 Ira W. Snyder <iws@ovro.caltech.edu>
+P2020RDB powerpc mpc85xx 743d4815 2015-01-23 Poonam Aggrwal <poonam.aggrwal@freescale.com>
+P2010RDB powerpc mpc85xx 743d4815 2015-01-23
+P1020RDB powerpc mpc85xx 743d4815 2015-01-23
+P1011RDB powerpc mpc85xx 743d4815 2015-01-23
+MPC8360EMDS powerpc mpc83xx 8d1e3cb1 2015-01-23 Dave Liu <daveliu@freescale.com>
+MPC8360ERDK powerpc mpc83xx 8d1e3cb1 2015-01-23 Anton Vorontsov <avorontsov@ru.mvista.com>
P3G4 powerpc 74xx_7xx d928664f 2015-01-16 Wolfgang Denk <wd@denx.de>
ZUMA powerpc 74xx_7xx d928664f 2015-01-16 Nye Liu <nyet@zumanetworks.com>
ppmc7xx powerpc 74xx_7xx d928664f 2015-01-16
diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h
deleted file mode 100644
index 0f4bd91..0000000
--- a/include/configs/mx31ads.h
+++ /dev/null
@@ -1,188 +0,0 @@
-/*
- * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
- *
- * Configuration settings for the MX31ADS Freescale board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
- /* High Level Configuration Options */
-#define CONFIG_MX31 1 /* This is a mx31 */
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#define CONFIG_SYS_TEXT_BASE 0xA0000000
-
-#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS
-
-/*
- * Disabled for now due to build problems under Debian and a significant increase
- * in the final file size: 144260 vs. 109536 Bytes.
- */
-#if 0
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_FIT 1
-#define CONFIG_FIT_VERBOSE 1
-#endif
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
-
-/*
- * Hardware drivers
- */
-
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-#define CONFIG_HARD_SPI 1
-#define CONFIG_MXC_SPI 1
-#define CONFIG_DEFAULT_SPI_BUS 1
-#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_MXC_GPIO
-
-/* PMIC Controller */
-#define CONFIG_POWER
-#define CONFIG_POWER_SPI
-#define CONFIG_POWER_FSL
-#define CONFIG_FSL_PMIC_BUS 1
-#define CONFIG_FSL_PMIC_CS 0
-#define CONFIG_FSL_PMIC_CLK 1000000
-#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_FSL_PMIC_BITLEN 32
-#define CONFIG_RTC_MC13XXX
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/***********************************************************
- * Command definition
- ***********************************************************/
-
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_DATE
-
-#define CONFIG_BOOTDELAY 3
-
-#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "uboot_addr=0xa0000000\0" \
- "uboot=mx31ads/u-boot.bin\0" \
- "kernel=mx31ads/uImage\0" \
- "nfsroot=/opt/eldk/arm\0" \
- "bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
- "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "bootcmd=run bootcmd_net\0" \
- "bootcmd_net=run bootargs_base bootargs_nfs; " \
- "tftpboot ${loadaddr} ${kernel}; bootm\0" \
- "prg_uboot=tftpboot ${loadaddr} ${uboot}; " \
- "protect off ${uboot_addr} 0xa003ffff; " \
- "erase ${uboot_addr} 0xa003ffff; " \
- "cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \
- "setenv filesize; saveenv\0"
-
-#define CONFIG_CS8900
-#define CONFIG_CS8900_BASE 0xb4020300
-#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */
-
-/*
- * The MX31ADS board seems to have a hardware "peculiarity" confirmed under
- * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A
- * controller inverted. The controller is capable of detecting and correcting
- * this, but it needs 4 network packets for that. Which means, at startup, you
- * will not receive answers to the first 4 packest, unless there have been some
- * broadcasts on the network, or your board is on a hub. Reducing the ARP
- * timeout from default 5 seconds to 200ms we speed up the initial TFTP
- * transfer, should the user wish one, significantly.
- */
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x10000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-#define CONFIG_CMDLINE_EDITING 1
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 CSD0_BASE
-#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
-#define CONFIG_BOARD_EARLY_INIT_F
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_GBL_DATA_OFFSET)
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE CS0_BASE
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE (128 * 1024)
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
-#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
-
-/*
- * JFFS2 partitions
- */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-
-#endif /* __CONFIG_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 2/9] ARM: mx31: remove imx31_phycore board
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-23 13:09 ` Anatolij Gustschin
2015-02-22 15:20 ` [U-Boot] [PATCH v4 3/9] ARM: remove jadecpu board support Masahiro Yamada
` (7 subsequent siblings)
9 siblings, 1 reply; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 5 -
board/imx31_phycore/Kconfig | 12 ---
board/imx31_phycore/MAINTAINERS | 11 --
board/imx31_phycore/Makefile | 9 --
board/imx31_phycore/imx31_phycore.c | 153 ---------------------------
board/imx31_phycore/lowlevel_init.S | 88 ----------------
configs/imx31_phycore_defconfig | 2 -
configs/imx31_phycore_eet_defconfig | 3 -
doc/README.scrapyard | 1 +
include/configs/imx31_phycore.h | 202 ------------------------------------
10 files changed, 1 insertion(+), 485 deletions(-)
delete mode 100644 board/imx31_phycore/Kconfig
delete mode 100644 board/imx31_phycore/MAINTAINERS
delete mode 100644 board/imx31_phycore/Makefile
delete mode 100644 board/imx31_phycore/imx31_phycore.c
delete mode 100644 board/imx31_phycore/lowlevel_init.S
delete mode 100644 configs/imx31_phycore_defconfig
delete mode 100644 configs/imx31_phycore_eet_defconfig
delete mode 100644 include/configs/imx31_phycore.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 7c8b324..57cee0c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -264,10 +264,6 @@ config TARGET_INTEGRATORCP_CM1136
bool "Support integratorcp_cm1136"
select CPU_ARM1136
-config TARGET_IMX31_PHYCORE
- bool "Support imx31_phycore"
- select CPU_ARM1136
-
config TARGET_QONG
bool "Support qong"
select CPU_ARM1136
@@ -812,7 +808,6 @@ source "board/gumstix/pepper/Kconfig"
source "board/h2200/Kconfig"
source "board/hale/tt01/Kconfig"
source "board/icpdas/lp8x4x/Kconfig"
-source "board/imx31_phycore/Kconfig"
source "board/isee/igep0033/Kconfig"
source "board/jornada/Kconfig"
source "board/karo/tx25/Kconfig"
diff --git a/board/imx31_phycore/Kconfig b/board/imx31_phycore/Kconfig
deleted file mode 100644
index d3d2025..0000000
--- a/board/imx31_phycore/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_IMX31_PHYCORE
-
-config SYS_BOARD
- default "imx31_phycore"
-
-config SYS_SOC
- default "mx31"
-
-config SYS_CONFIG_NAME
- default "imx31_phycore"
-
-endif
diff --git a/board/imx31_phycore/MAINTAINERS b/board/imx31_phycore/MAINTAINERS
deleted file mode 100644
index 41f6cae..0000000
--- a/board/imx31_phycore/MAINTAINERS
+++ /dev/null
@@ -1,11 +0,0 @@
-IMX31_PHYCORE BOARD
-#M: -
-S: Maintained
-F: board/imx31_phycore/
-F: include/configs/imx31_phycore.h
-F: configs/imx31_phycore_defconfig
-
-IMX31_PHYCORE_EET BOARD
-#M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
-S: Orphan (since 2013-09)
-F: configs/imx31_phycore_eet_defconfig
diff --git a/board/imx31_phycore/Makefile b/board/imx31_phycore/Makefile
deleted file mode 100644
index e781c13..0000000
--- a/board/imx31_phycore/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := imx31_phycore.o
-obj-y += lowlevel_init.o
diff --git a/board/imx31_phycore/imx31_phycore.c b/board/imx31_phycore/imx31_phycore.c
deleted file mode 100644
index 3f45e4e..0000000
--- a/board/imx31_phycore/imx31_phycore.c
+++ /dev/null
@@ -1,153 +0,0 @@
-/*
- *
- * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#include <common.h>
-#include <s6e63d6.h>
-#include <netdev.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-int board_init(void)
-{
-
- gd->bd->bi_arch_number = MACH_TYPE_PCM037; /* board id for linux */
- gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */
-
- return 0;
-}
-
-int board_early_init_f(void)
-{
- /* CS0: Nor Flash */
- static const struct mxc_weimcs cs0 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 3, 15, 0, 0, 3),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(1, 0, 0, 0, 0, 1, 5, 0, 0, 0, 1, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(0, 0, 7, 2, 0, 0, 2, 1, 0, 0, 0, 0, 0, 0)
- };
-
- /* CS1: Network Controller */
- static const struct mxc_weimcs cs1 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 3, 31, 0, 0, 6),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(4, 4, 4, 10, 4, 0, 5, 4, 0, 0, 0, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(4, 4, 4, 4, 0, 1, 4, 3, 0, 0, 0, 0, 1, 0)
- };
-
- /* CS4: SRAM */
- static const struct mxc_weimcs cs4 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 3, 24, 0, 4, 3),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(2, 2, 2, 5, 2, 0, 5, 2, 0, 0, 0, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(2, 2, 2, 2, 0, 0, 2, 2, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(0, &cs0);
- mxc_setup_weimcs(1, &cs1);
- mxc_setup_weimcs(4, &cs4);
-
- /* setup pins for UART1 */
- mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
- mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
- mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
- mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);
-
- /* setup pins for I2C2 (for EEPROM, RTC) */
- mx31_gpio_mux(MUX_CSPI2_MOSI__I2C2_SCL);
- mx31_gpio_mux(MUX_CSPI2_MISO__I2C2_SDA);
-
- return 0;
-}
-
-#ifdef CONFIG_BOARD_LATE_INIT
-int board_late_init(void)
-{
-#ifdef CONFIG_S6E63D6
- struct s6e63d6 data = {
- /*
- * See comment in mxc_spi.c::decode_cs() for .cs field format.
- * We use GPIO 57 as a chipselect for the S6E63D6 and chipselect
- * 2 of the SPI controller #1, since it is unused.
- */
- .cs = 2 | (57 << 8),
- .bus = 0,
- .id = 0,
- };
- int ret;
-
- /* SPI1 */
- mx31_gpio_mux(MUX_CSPI1_SCLK__CSPI1_CLK);
- mx31_gpio_mux(MUX_CSPI1_SPI_RDY__CSPI1_DATAREADY_B);
- mx31_gpio_mux(MUX_CSPI1_MOSI__CSPI1_MOSI);
- mx31_gpio_mux(MUX_CSPI1_MISO__CSPI1_MISO);
- mx31_gpio_mux(MUX_CSPI1_SS0__CSPI1_SS0_B);
- mx31_gpio_mux(MUX_CSPI1_SS1__CSPI1_SS1_B);
- mx31_gpio_mux(MUX_CSPI1_SS2__CSPI1_SS2_B);
-
- /* start SPI1 clock */
- __REG(CCM_CGR2) = __REG(CCM_CGR2) | (3 << 2);
-
- /* GPIO 57 */
- /* sw_mux_ctl_key_col4_key_col5_key_col6_key_col7 */
- mx31_gpio_mux(IOMUX_MODE(0x63, MUX_CTL_GPIO));
-
- /* SPI1 CS2 is free */
- ret = s6e63d6_init(&data);
- if (ret)
- return ret;
-
- /*
- * This is a "magic" sequence to initialise a C0240QGLA / C0283QGLC
- * OLED display connected to a S6E63D6 SPI display controller in the
- * 18 bit RGB mode
- */
- s6e63d6_index(&data, 2);
- s6e63d6_param(&data, 0x0182);
- s6e63d6_index(&data, 3);
- s6e63d6_param(&data, 0x8130);
- s6e63d6_index(&data, 0x10);
- s6e63d6_param(&data, 0x0000);
- s6e63d6_index(&data, 5);
- s6e63d6_param(&data, 0x0001);
- s6e63d6_index(&data, 0x22);
-#endif
- return 0;
-}
-#endif
-
-int checkboard (void)
-{
- printf("Board: Phytec phyCore i.MX31\n");
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC911X
- rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
- return rc;
-}
diff --git a/board/imx31_phycore/lowlevel_init.S b/board/imx31_phycore/lowlevel_init.S
deleted file mode 100644
index 6ea3878..0000000
--- a/board/imx31_phycore/lowlevel_init.S
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- *
- * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm/arch/imx-regs.h>
-
-.macro REG reg, val
- ldr r2, =\reg
- ldr r3, =\val
- str r3, [r2]
-.endm
-
-.macro REG8 reg, val
- ldr r2, =\reg
- ldr r3, =\val
- strb r3, [r2]
-.endm
-
-.macro DELAY loops
- ldr r2, =\loops
-1:
- subs r2, r2, #1
- nop
- bcs 1b
-.endm
-
-.globl lowlevel_init
-lowlevel_init:
-
- REG IPU_CONF, IPU_CONF_DI_EN
- REG CCM_CCMR, 0x074B0BF5
-
- DELAY 0x40000
-
- REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE
- REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS
-
- REG CCM_PDR0, PDR0_CSI_PODF(0x3f) | PDR0_CSI_PRDF(7) | PDR0_PER_PODF(7) | PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | PDR0_MCU_PODF(0)
-
- REG CCM_MPCTL, PLL_PD(0) | PLL_MFD(0xe) | PLL_MFI(9) | PLL_MFN(0xd)
-
- REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(0x43) | PLL_MFI(12) | PLL_MFN(1)
-
- REG 0x43FAC26C, 0 /* SDCLK */
- REG 0x43FAC270, 0 /* CAS */
- REG 0x43FAC274, 0 /* RAS */
- REG 0x43FAC27C, 0x1000 /* CS2 (CSD0) */
- REG 0x43FAC284, 0 /* DQM3 */
- REG 0x43FAC288, 0 /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */
- REG 0x43FAC28C, 0
- REG 0x43FAC290, 0
- REG 0x43FAC294, 0
- REG 0x43FAC298, 0
- REG 0x43FAC29C, 0
- REG 0x43FAC2A0, 0
- REG 0x43FAC2A4, 0
- REG 0x43FAC2A8, 0
- REG 0x43FAC2AC, 0
- REG 0x43FAC2B0, 0
- REG 0x43FAC2B4, 0
- REG 0x43FAC2B8, 0
- REG 0x43FAC2BC, 0
- REG 0x43FAC2C0, 0
- REG 0x43FAC2C4, 0
- REG 0x43FAC2C8, 0
- REG 0x43FAC2CC, 0
- REG 0x43FAC2D0, 0
- REG 0x43FAC2D4, 0
- REG 0x43FAC2D8, 0
- REG 0x43FAC2DC, 0
- REG 0xB8001010, 0x00000004
- REG 0xB8001004, 0x006ac73a
- REG 0xB8001000, 0x92100000
- REG 0x80000f00, 0x12344321
- REG 0xB8001000, 0xa2100000
- REG 0x80000000, 0x12344321
- REG 0x80000000, 0x12344321
- REG 0xB8001000, 0xb2100000
- REG8 0x80000033, 0xda
- REG8 0x81000000, 0xff
- REG 0xB8001000, 0x82226080
- REG 0x80000000, 0xDEADBEEF
- REG 0xB8001010, 0x0000000c
-
- mov pc, lr
diff --git a/configs/imx31_phycore_defconfig b/configs/imx31_phycore_defconfig
deleted file mode 100644
index 563de57..0000000
--- a/configs/imx31_phycore_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_IMX31_PHYCORE=y
diff --git a/configs/imx31_phycore_eet_defconfig b/configs/imx31_phycore_eet_defconfig
deleted file mode 100644
index 9531952..0000000
--- a/configs/imx31_phycore_eet_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="IMX31_PHYCORE_EET"
-CONFIG_ARM=y
-CONFIG_TARGET_IMX31_PHYCORE=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index c6f3d14..cd51249 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+imx31_phycore arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
mx31ads arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
icecube_5200 powerpc mpc5xxx 37b608a5 2015-01-23 Wolfgang Denk <wd@denx.de>
Lite5200 powerpc mpc5xxx 37b608a5 2015-01-23
diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h
deleted file mode 100644
index 4195fa3..0000000
--- a/include/configs/imx31_phycore.h
+++ /dev/null
@@ -1,202 +0,0 @@
-/*
- * (C) Copyright 2004
- * Texas Instruments.
- * Richard Woodruff <r-woodruff2@ti.com>
- * Kshitij Gupta <kshitij@ti.com>
- *
- * Configuration settings for the phyCORE-i.MX31 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
-/* High Level Configuration Options */
-#define CONFIG_MX31 /* This is a mx31 */
-#define CONFIG_MX31_CLK32 32000
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 512 * 1024)
-
-/*
- * Hardware drivers
- */
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_CLK_OFFSET I2C2_CLK_OFFSET
-
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/***********************************************************
- * Command definition
- ***********************************************************/
-
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-
-#define CONFIG_BOOTDELAY 3
-
-#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:128k(uboot)ro," \
- "1536k(kernel),-(root)"
-
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.23.168
-#define CONFIG_SERVERIP 192.168.23.2
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootargs_base=setenv bootargs console=ttySMX0,115200\0" \
- "bootargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs " \
- "ip=dhcp nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \
- "bootargs_flash=setenv bootargs $(bootargs) " \
- "root=/dev/mtdblock2 rootfstype=jffs2\0" \
- "bootargs_mtd=setenv bootargs $(bootargs) $(mtdparts)\0" \
- "bootcmd=run bootcmd_net\0" \
- "bootcmd_net=run bootargs_base bootargs_mtd bootargs_nfs;" \
- "tftpboot 0x80000000 $(uimage);bootm\0" \
- "bootcmd_flash=run bootargs_base bootargs_mtd bootargs_flash;" \
- "bootm 0x80000000\0" \
- "unlock=yes\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
- "prg_uboot=tftpboot 0x80000000 $(uboot);" \
- "protect off 0xa0000000 +0x20000;" \
- "erase 0xa0000000 +0x20000;" \
- "cp.b 0x80000000 0xa0000000 $(filesize)\0" \
- "prg_kernel=tftpboot 0x80000000 $(uimage);" \
- "erase 0xa0040000 +0x180000;" \
- "cp.b 0x80000000 0xa0040000 $(filesize)\0" \
- "prg_jffs2=tftpboot 0x80000000 $(jffs2);" \
- "erase 0xa01c0000 0xa1ffffff;" \
- "cp.b 0x80000000 0xa01c0000 $(filesize)\0" \
- "videomode=video=ctfb:x:240,y:320,depth:16,mode:0," \
- "pclk:185925,le:9,ri:17,up:7,lo:10,hs:1,vs:1," \
- "sync:1241513985,vmode:0\0"
-
-
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0xa8000000
-#define CONFIG_SMC911X_32_BIT
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "uboot> "
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE 256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS 16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x10000
-
-#define CONFIG_SYS_LOAD_ADDR 0 /* default load address */
-
-#define CONFIG_CMDLINE_EDITING
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 0x80000000
-#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_SYS_TEXT_BASE 0xA0000000
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_GBL_DATA_OFFSET)
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE 0xa0000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max # of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max # of sectors/chip */
-/* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_ENV_OFFSET 0x00 /* env. starts here */
-#define CONFIG_ENV_SIZE 4096
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 5 bits = 32 octets */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10 ms delay */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* byte addr. lenght */
-
-/*
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/mtd/cfi_flash.c */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */
-
-/*
- * Timeout for Flash Erase and Flash Write
- * timeout values are in ticks
- */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100*CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100*CONFIG_SYS_HZ)
-
-/*
- * JFFS2 partitions
- */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-
-/* EET platform additions */
-#ifdef CONFIG_IMX31_PHYCORE_EET
-#define CONFIG_BOARD_LATE_INIT
-
-#define CONFIG_MXC_GPIO
-
-#define CONFIG_HARD_SPI
-#define CONFIG_MXC_SPI
-#define CONFIG_CMD_SPI
-
-#define CONFIG_S6E63D6
-
-#define CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_MX3
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_CMD_BMP
-#define CONFIG_BMP_16BPP
-#endif
-
-#endif /* __CONFIG_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 3/9] ARM: remove jadecpu board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 2/9] ARM: mx31: remove imx31_phycore board Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 4/9] ARM: remove zmx25 " Masahiro Yamada
` (6 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 5 -
arch/arm/cpu/arm926ejs/Makefile | 1 -
arch/arm/cpu/arm926ejs/mb86r0x/Makefile | 8 -
arch/arm/cpu/arm926ejs/mb86r0x/clock.c | 27 --
arch/arm/cpu/arm926ejs/mb86r0x/reset.c | 24 --
arch/arm/cpu/arm926ejs/mb86r0x/timer.c | 115 -----
arch/arm/include/asm/arch-mb86r0x/hardware.h | 15 -
arch/arm/include/asm/arch-mb86r0x/mb86r0x.h | 599 ---------------------------
arch/arm/lib/asm-offsets.c | 46 --
board/syteco/jadecpu/Kconfig | 15 -
board/syteco/jadecpu/MAINTAINERS | 6 -
board/syteco/jadecpu/Makefile | 13 -
board/syteco/jadecpu/jadecpu.c | 160 -------
board/syteco/jadecpu/lowlevel_init.S | 249 -----------
configs/jadecpu_defconfig | 2 -
doc/README.scrapyard | 1 +
drivers/video/Makefile | 1 -
drivers/video/mb86r0xgdc.c | 168 --------
include/configs/jadecpu.h | 273 ------------
include/serial.h | 2 +-
20 files changed, 2 insertions(+), 1728 deletions(-)
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/Makefile
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/clock.c
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/reset.c
delete mode 100644 arch/arm/cpu/arm926ejs/mb86r0x/timer.c
delete mode 100644 arch/arm/include/asm/arch-mb86r0x/hardware.h
delete mode 100644 arch/arm/include/asm/arch-mb86r0x/mb86r0x.h
delete mode 100644 board/syteco/jadecpu/Kconfig
delete mode 100644 board/syteco/jadecpu/MAINTAINERS
delete mode 100644 board/syteco/jadecpu/Makefile
delete mode 100644 board/syteco/jadecpu/jadecpu.c
delete mode 100644 board/syteco/jadecpu/lowlevel_init.S
delete mode 100644 configs/jadecpu_defconfig
delete mode 100644 drivers/video/mb86r0xgdc.c
delete mode 100644 include/configs/jadecpu.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 57cee0c..b24fb18 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -144,10 +144,6 @@ config TARGET_DEVKIT3250
bool "Support devkit3250"
select CPU_ARM926EJS
-config TARGET_JADECPU
- bool "Support jadecpu"
- select CPU_ARM926EJS
-
config TARGET_MX25PDK
bool "Support mx25pdk"
select CPU_ARM926EJS
@@ -843,7 +839,6 @@ source "board/st-ericsson/snowball/Kconfig"
source "board/st-ericsson/u8500/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/sunxi/Kconfig"
-source "board/syteco/jadecpu/Kconfig"
source "board/syteco/zmx25/Kconfig"
source "board/tbs/tbs2910/Kconfig"
source "board/ti/am335x/Kconfig"
diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile
index f5944cc..ac23116 100644
--- a/arch/arm/cpu/arm926ejs/Makefile
+++ b/arch/arm/cpu/arm926ejs/Makefile
@@ -16,7 +16,6 @@ endif
obj-$(CONFIG_ARMADA100) += armada100/
obj-$(if $(filter lpc32xx,$(SOC)),y) += lpc32xx/
-obj-$(CONFIG_MB86R0x) += mb86r0x/
obj-$(CONFIG_MX25) += mx25/
obj-$(CONFIG_MX27) += mx27/
obj-$(if $(filter mxs,$(SOC)),y) += mxs/
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/Makefile b/arch/arm/cpu/arm926ejs/mb86r0x/Makefile
deleted file mode 100644
index 365892c..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = clock.o reset.o timer.o
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/clock.c b/arch/arm/cpu/arm926ejs/mb86r0x/clock.c
deleted file mode 100644
index 1f6f66e..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/clock.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-/*
- * Get the peripheral bus frequency depending on pll pin settings
- */
-ulong get_bus_freq(ulong dummy)
-{
- struct mb86r0x_crg * crg = (struct mb86r0x_crg *)
- MB86R0x_CRG_BASE;
- uint32_t pllmode;
-
- pllmode = readl(&crg->crpr) & MB86R0x_CRG_CRPR_PLLMODE;
-
- if (pllmode == MB86R0x_CRG_CRPR_PLLMODE_X20)
- return 40000000;
-
- return 41164767;
-}
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/reset.c b/arch/arm/cpu/arm926ejs/mb86r0x/reset.c
deleted file mode 100644
index 7bd77ff..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/reset.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-/*
- * Reset the cpu by setting software reset request bit
- */
-void reset_cpu(ulong ignored)
-{
- struct mb86r0x_crg * crg = (struct mb86r0x_crg *)
- MB86R0x_CRG_BASE;
-
- writel(MB86R0x_CRSR_SWRSTREQ, &crg->crsr);
- while (1)
- /* NOP */;
- /* Never reached */
-}
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/timer.c b/arch/arm/cpu/arm926ejs/mb86r0x/timer.c
deleted file mode 100644
index bb07819..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/timer.c
+++ /dev/null
@@ -1,115 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian@popies.net>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * (C) Copyright 2010
- * Matthias Weisser, Graf-Syteco <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <div64.h>
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-#define TIMER_LOAD_VAL 0xffffffff
-#define TIMER_FREQ (CONFIG_MB86R0x_IOCLK / 256)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define timestamp gd->arch.tbl
-#define lastdec gd->arch.lastinc
-
-static inline unsigned long long tick_to_time(unsigned long long tick)
-{
- tick *= CONFIG_SYS_HZ;
- do_div(tick, TIMER_FREQ);
-
- return tick;
-}
-
-static inline unsigned long long usec_to_tick(unsigned long long usec)
-{
- usec *= TIMER_FREQ;
- do_div(usec, 1000000);
-
- return usec;
-}
-
-/* nothing really to do with interrupts, just starts up a counter. */
-int timer_init(void)
-{
- struct mb86r0x_timer * timer = (struct mb86r0x_timer *)
- MB86R0x_TIMER_BASE;
- ulong ctrl = readl(&timer->control);
-
- writel(TIMER_LOAD_VAL, &timer->load);
-
- ctrl |= MB86R0x_TIMER_ENABLE | MB86R0x_TIMER_PRS_8S |
- MB86R0x_TIMER_SIZE_32;
-
- writel(ctrl, &timer->control);
-
- /* capture current value time */
- lastdec = readl(&timer->value);
- timestamp = 0; /* start "advancing" time stamp from 0 */
-
- return 0;
-}
-
-/*
- * timer without interrupts
- */
-unsigned long long get_ticks(void)
-{
- struct mb86r0x_timer * timer = (struct mb86r0x_timer *)
- MB86R0x_TIMER_BASE;
- ulong now = readl(&timer->value);
-
- if (now <= lastdec) {
- /* normal mode (non roll) */
- /* move stamp forward with absolut diff ticks */
- timestamp += lastdec - now;
- } else {
- /* we have rollover of incrementer */
- timestamp += lastdec + TIMER_LOAD_VAL - now;
- }
- lastdec = now;
- return timestamp;
-}
-
-ulong get_timer_masked(void)
-{
- return tick_to_time(get_ticks());
-}
-
-void __udelay(unsigned long usec)
-{
- unsigned long long tmp;
- ulong tmo;
-
- tmo = usec_to_tick(usec);
- tmp = get_ticks(); /* get current timestamp */
-
- while ((get_ticks() - tmp) < tmo) /* loop till event */
- /*NOP*/;
-}
-
-ulong get_timer(ulong base)
-{
- return get_timer_masked() - base;
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk(void)
-{
- ulong tbclk;
-
- tbclk = TIMER_FREQ;
- return tbclk;
-}
diff --git a/arch/arm/include/asm/arch-mb86r0x/hardware.h b/arch/arm/include/asm/arch-mb86r0x/hardware.h
deleted file mode 100644
index 42a52bc..0000000
--- a/arch/arm/include/asm/arch-mb86r0x/hardware.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * (C) Copyright 2007
- *
- * Author : Carsten Schneider, mycable GmbH
- * <cs@mycable.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <linux/sizes.h>
-#include <asm/arch/mb86r0x.h>
-
-#endif
diff --git a/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h b/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h
deleted file mode 100644
index 7fec971..0000000
--- a/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h
+++ /dev/null
@@ -1,599 +0,0 @@
-/*
- * (C) Copyright 2007
- *
- * mb86r0x definitions
- *
- * Author : Carsten Schneider, mycable GmbH
- * <cs@mycable.de>
- *
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef MB86R0X_H
-#define MB86R0X_H
-
-#ifndef __ASSEMBLY__
-
-/* GPIO registers */
-struct mb86r0x_gpio {
- uint32_t gpdr0;
- uint32_t gpdr1;
- uint32_t gpdr2;
- uint32_t res;
- uint32_t gpddr0;
- uint32_t gpddr1;
- uint32_t gpddr2;
-};
-
-/* PWM registers */
-struct mb86r0x_pwm {
- uint32_t bcr;
- uint32_t tpr;
- uint32_t pr;
- uint32_t dr;
- uint32_t cr;
- uint32_t sr;
- uint32_t ccr;
- uint32_t ir;
-};
-
-/* The mb86r0x chip control (CCNT) register set. */
-struct mb86r0x_ccnt {
- uint32_t ccid;
- uint32_t csrst;
- uint32_t pad0[2];
- uint32_t cist;
- uint32_t cistm;
- uint32_t cgpio_ist;
- uint32_t cgpio_istm;
- uint32_t cgpio_ip;
- uint32_t cgpio_im;
- uint32_t caxi_bw;
- uint32_t caxi_ps;
- uint32_t cmux_md;
- uint32_t cex_pin_st;
- uint32_t cmlb;
- uint32_t pad1[1];
- uint32_t cusb;
- uint32_t pad2[41];
- uint32_t cbsc;
- uint32_t cdcrc;
- uint32_t cmsr0;
- uint32_t cmsr1;
- uint32_t pad3[2];
-};
-
-/* The mb86r0x clock reset generator */
-struct mb86r0x_crg {
- uint32_t crpr;
- uint32_t pad0;
- uint32_t crwr;
- uint32_t crsr;
- uint32_t crda;
- uint32_t crdb;
- uint32_t crha;
- uint32_t crpa;
- uint32_t crpb;
- uint32_t crhb;
- uint32_t cram;
-};
-
-/* The mb86r0x timer */
-struct mb86r0x_timer {
- uint32_t load;
- uint32_t value;
- uint32_t control;
- uint32_t intclr;
- uint32_t ris;
- uint32_t mis;
- uint32_t bgload;
-};
-
-/* mb86r0x gdc display controller */
-struct mb86r0x_gdc_dsp {
- /* Display settings */
- uint32_t dcm0;
- uint16_t pad00;
- uint16_t htp;
- uint16_t hdp;
- uint16_t hdb;
- uint16_t hsp;
- uint8_t hsw;
- uint8_t vsw;
- uint16_t pad01;
- uint16_t vtr;
- uint16_t vsp;
- uint16_t vdp;
- uint16_t wx;
- uint16_t wy;
- uint16_t ww;
- uint16_t wh;
-
- /* Layer 0 */
- uint32_t l0m;
- uint32_t l0oa;
- uint32_t l0da;
- uint16_t l0dx;
- uint16_t l0dy;
-
- /* Layer 1 */
- uint32_t l1m;
- uint32_t cbda0;
- uint32_t cbda1;
- uint32_t pad02;
-
- /* Layer 2 */
- uint32_t l2m;
- uint32_t l2oa0;
- uint32_t l2da0;
- uint32_t l2oa1;
- uint32_t l2da1;
- uint16_t l2dx;
- uint16_t l2dy;
-
- /* Layer 3 */
- uint32_t l3m;
- uint32_t l3oa0;
- uint32_t l3da0;
- uint32_t l3oa1;
- uint32_t l3da1;
- uint16_t l3dx;
- uint16_t l3dy;
-
- /* Layer 4 */
- uint32_t l4m;
- uint32_t l4oa0;
- uint32_t l4da0;
- uint32_t l4oa1;
- uint32_t l4da1;
- uint16_t l4dx;
- uint16_t l4dy;
-
- /* Layer 5 */
- uint32_t l5m;
- uint32_t l5oa0;
- uint32_t l5da0;
- uint32_t l5oa1;
- uint32_t l5da1;
- uint16_t l5dx;
- uint16_t l5dy;
-
- /* Cursor */
- uint16_t cutc;
- uint8_t cpm;
- uint8_t csize;
- uint32_t cuoa0;
- uint16_t cux0;
- uint16_t cuy0;
- uint32_t cuoa1;
- uint16_t cux1;
- uint16_t cuy1;
-
- /* Layer blending */
- uint32_t l0bld;
- uint32_t pad03;
- uint32_t l0tc;
- uint16_t l3tc;
- uint16_t l2tc;
- uint32_t pad04[15];
-
- /* Display settings */
- uint32_t dcm1;
- uint32_t dcm2;
- uint32_t dcm3;
- uint32_t pad05;
-
- /* Layer 0 extended */
- uint32_t l0em;
- uint16_t l0wx;
- uint16_t l0wy;
- uint16_t l0ww;
- uint16_t l0wh;
- uint32_t pad06;
-
- /* Layer 1 extended */
- uint32_t l1em;
- uint16_t l1wx;
- uint16_t l1wy;
- uint16_t l1ww;
- uint16_t l1wh;
- uint32_t pad07;
-
- /* Layer 2 extended */
- uint32_t l2em;
- uint16_t l2wx;
- uint16_t l2wy;
- uint16_t l2ww;
- uint16_t l2wh;
- uint32_t pad08;
-
- /* Layer 3 extended */
- uint32_t l3em;
- uint16_t l3wx;
- uint16_t l3wy;
- uint16_t l3ww;
- uint16_t l3wh;
- uint32_t pad09;
-
- /* Layer 4 extended */
- uint32_t l4em;
- uint16_t l4wx;
- uint16_t l4wy;
- uint16_t l4ww;
- uint16_t l4wh;
- uint32_t pad10;
-
- /* Layer 5 extended */
- uint32_t l5em;
- uint16_t l5wx;
- uint16_t l5wy;
- uint16_t l5ww;
- uint16_t l5wh;
- uint32_t pad11;
-
- /* Multi screen control */
- uint32_t msc;
- uint32_t pad12[3];
- uint32_t dls;
- uint32_t dbgc;
-
- /* Layer blending */
- uint32_t l1bld;
- uint32_t l2bld;
- uint32_t l3bld;
- uint32_t l4bld;
- uint32_t l5bld;
- uint32_t pad13;
-
- /* Extended transparency control */
- uint32_t l0etc;
- uint32_t l1etc;
- uint32_t l2etc;
- uint32_t l3etc;
- uint32_t l4etc;
- uint32_t l5etc;
- uint32_t pad14[10];
-
- /* YUV coefficients */
- uint32_t l1ycr0;
- uint32_t l1ycr1;
- uint32_t l1ycg0;
- uint32_t l1ycg1;
- uint32_t l1ycb0;
- uint32_t l1ycb1;
- uint32_t pad15[130];
-
- /* Layer palletes */
- uint32_t l0pal[256];
- uint32_t l1pal[256];
- uint32_t pad16[256];
- uint32_t l2pal[256];
- uint32_t l3pal[256];
- uint32_t pad17[256];
-
- /* PWM settings */
- uint32_t vpwmm;
- uint16_t vpwms;
- uint16_t vpwme;
- uint32_t vpwmc;
- uint32_t pad18[253];
-};
-
-/* mb86r0x gdc capture controller */
-struct mb86r0x_gdc_cap {
- uint32_t vcm;
- uint32_t csc;
- uint32_t vcs;
- uint32_t pad01;
-
- uint32_t cbm;
- uint32_t cboa;
- uint32_t cbla;
- uint16_t cihstr;
- uint16_t civstr;
- uint16_t cihend;
- uint16_t civend;
- uint32_t pad02;
-
- uint32_t chp;
- uint32_t cvp;
- uint32_t pad03[4];
-
- uint32_t clpf;
- uint32_t pad04;
- uint32_t cmss;
- uint32_t cmds;
- uint32_t pad05[12];
-
- uint32_t rgbhc;
- uint32_t rgbhen;
- uint32_t rgbven;
- uint32_t pad06;
- uint32_t rgbs;
- uint32_t pad07[11];
-
- uint32_t rgbcmy;
- uint32_t rgbcmcb;
- uint32_t rgbcmcr;
- uint32_t rgbcmb;
- uint32_t pad08[12 + 1984];
-};
-
-/* mb86r0x gdc draw */
-struct mb86r0x_gdc_draw {
- uint32_t ys;
- uint32_t xs;
- uint32_t dxdy;
- uint32_t xus;
- uint32_t dxudy;
- uint32_t xls;
- uint32_t dxldy;
- uint32_t usn;
- uint32_t lsn;
- uint32_t pad01[7];
- uint32_t rs;
- uint32_t drdx;
- uint32_t drdy;
- uint32_t gs;
- uint32_t dgdx;
- uint32_t dgdy;
- uint32_t bs;
- uint32_t dbdx;
- uint32_t dbdy;
- uint32_t pad02[7];
- uint32_t zs;
- uint32_t dzdx;
- uint32_t dzdy;
- uint32_t pad03[13];
- uint32_t ss;
- uint32_t dsdx;
- uint32_t dsdy;
- uint32_t ts;
- uint32_t dtdx;
- uint32_t dtdy;
- uint32_t qs;
- uint32_t dqdx;
- uint32_t dqdy;
- uint32_t pad04[23];
- uint32_t lpn;
- uint32_t lxs;
- uint32_t lxde;
- uint32_t lys;
- uint32_t lyde;
- uint32_t lzs;
- uint32_t lzde;
- uint32_t pad05[13];
- uint32_t pxdc;
- uint32_t pydc;
- uint32_t pzdc;
- uint32_t pad06[25];
- uint32_t rxs;
- uint32_t rys;
- uint32_t rsizex;
- uint32_t rsizey;
- uint32_t pad07[12];
- uint32_t saddr;
- uint32_t sstride;
- uint32_t srx;
- uint32_t sry;
- uint32_t daddr;
- uint32_t dstride;
- uint32_t drx;
- uint32_t dry;
- uint32_t brsizex;
- uint32_t brsizey;
- uint32_t tcolor;
- uint32_t pad08[93];
- uint32_t blpo;
- uint32_t pad09[7];
- uint32_t ctr;
- uint32_t ifsr;
- uint32_t ifcnt;
- uint32_t sst;
- uint32_t ds;
- uint32_t pst;
- uint32_t est;
- uint32_t pad10;
- uint32_t mdr0;
- uint32_t mdr1;
- uint32_t mdr2;
- uint32_t mdr3;
- uint32_t mdr4;
- uint32_t pad14[2];
- uint32_t mdr7;
- uint32_t fbr;
- uint32_t xres;
- uint32_t zbr;
- uint32_t tbr;
- uint32_t pfbr;
- uint32_t cxmin;
- uint32_t cxmax;
- uint32_t cymin;
- uint32_t cymax;
- uint32_t txs;
- uint32_t tis;
- uint32_t toa;
- uint32_t sho;
- uint32_t abr;
- uint32_t pad15[2];
- uint32_t fc;
- uint32_t bc;
- uint32_t alf;
- uint32_t blp;
- uint32_t pad16;
- uint32_t tbc;
- uint32_t pad11[42];
- uint32_t lx0dc;
- uint32_t ly0dc;
- uint32_t lx1dc;
- uint32_t ly1dc;
- uint32_t pad12[12];
- uint32_t x0dc;
- uint32_t y0dc;
- uint32_t x1dc;
- uint32_t y1dc;
- uint32_t x2dc;
- uint32_t y2dc;
- uint32_t pad13[666];
-};
-
-/* mb86r0x gdc geometry engine */
-struct mb86r0x_gdc_geom {
- uint32_t gctr;
- uint32_t pad00[15];
- uint32_t gmdr0;
- uint32_t gmdr1;
- uint32_t gmdr2;
- uint32_t pad01[237];
- uint32_t dfifog;
- uint32_t pad02[767];
-};
-
-/* mb86r0x gdc */
-struct mb86r0x_gdc {
- uint32_t pad00[2];
- uint32_t lts;
- uint32_t pad01;
- uint32_t lsta;
- uint32_t pad02[3];
- uint32_t ist;
- uint32_t imask;
- uint32_t pad03[6];
- uint32_t lsa;
- uint32_t lco;
- uint32_t lreq;
-
- uint32_t pad04[16*1024 - 19];
- struct mb86r0x_gdc_dsp dsp0;
- struct mb86r0x_gdc_dsp dsp1;
- uint32_t pad05[4*1024 - 2];
- uint32_t vccc;
- uint32_t vcsr;
- struct mb86r0x_gdc_cap cap0;
- struct mb86r0x_gdc_cap cap1;
- uint32_t pad06[4*1024];
- uint32_t texture_base[16*1024];
- struct mb86r0x_gdc_draw draw;
- uint32_t pad07[7*1024];
- struct mb86r0x_gdc_geom geom;
- uint32_t pad08[7*1024];
-};
-
-/* mb86r0x ddr2c */
-struct mb86r0x_ddr2c {
- uint16_t dric;
- uint16_t dric1;
- uint16_t dric2;
- uint16_t drca;
- uint16_t drcm;
- uint16_t drcst1;
- uint16_t drcst2;
- uint16_t drcr;
- uint16_t pad00[8];
- uint16_t drcf;
- uint16_t pad01[7];
- uint16_t drasr;
- uint16_t pad02[15];
- uint16_t drims;
- uint16_t pad03[7];
- uint16_t dros;
- uint16_t pad04;
- uint16_t dribsodt1;
- uint16_t dribsocd;
- uint16_t dribsocd2;
- uint16_t pad05[3];
- uint16_t droaba;
- uint16_t pad06[9];
- uint16_t drobs;
- uint16_t pad07[5];
- uint16_t drimr1;
- uint16_t drimr2;
- uint16_t drimr3;
- uint16_t drimr4;
- uint16_t droisr1;
- uint16_t droisr2;
-};
-
-/* mb86r0x memc */
-struct mb86r0x_memc {
- uint32_t mcfmode[8];
- uint32_t mcftim[8];
- uint32_t mcfarea[8];
-};
-
-#endif /* __ASSEMBLY__ */
-
-/*
- * Physical Address Defines
- */
-#define MB86R0x_DDR2_BASE 0xf3000000
-#define MB86R0x_GDC_BASE 0xf1fc0000
-#define MB86R0x_CCNT_BASE 0xfff42000
-#define MB86R0x_CAN0_BASE 0xfff54000
-#define MB86R0x_CAN1_BASE 0xfff55000
-#define MB86R0x_I2C0_BASE 0xfff56000
-#define MB86R0x_I2C1_BASE 0xfff57000
-#define MB86R0x_EHCI_BASE 0xfff80000
-#define MB86R0x_OHCI_BASE 0xfff81000
-#define MB86R0x_IRC1_BASE 0xfffb0000
-#define MB86R0x_MEMC_BASE 0xfffc0000
-#define MB86R0x_TIMER_BASE 0xfffe0000
-#define MB86R0x_UART0_BASE 0xfffe1000
-#define MB86R0x_UART1_BASE 0xfffe2000
-#define MB86R0x_IRCE_BASE 0xfffe4000
-#define MB86R0x_CRG_BASE 0xfffe7000
-#define MB86R0x_IRC0_BASE 0xfffe8000
-#define MB86R0x_GPIO_BASE 0xfffe9000
-#define MB86R0x_PWM0_BASE 0xfff41000
-#define MB86R0x_PWM1_BASE 0xfff41100
-
-#define MB86R0x_CRSR_SWRSTREQ (1 << 1)
-
-/*
- * Timer register bits
- */
-#define MB86R0x_TIMER_ENABLE (1 << 7)
-#define MB86R0x_TIMER_MODE_MSK (1 << 6)
-#define MB86R0x_TIMER_MODE_FR (0 << 6)
-#define MB86R0x_TIMER_MODE_PD (1 << 6)
-
-#define MB86R0x_TIMER_INT_EN (1 << 5)
-#define MB86R0x_TIMER_PRS_MSK (3 << 2)
-#define MB86R0x_TIMER_PRS_4S (1 << 2)
-#define MB86R0x_TIMER_PRS_8S (1 << 3)
-#define MB86R0x_TIMER_SIZE_32 (1 << 1)
-#define MB86R0x_TIMER_ONE_SHT (1 << 0)
-
-/*
- * Clock reset generator bits
- */
-#define MB86R0x_CRG_CRPR_PLLRDY (1 << 8)
-#define MB86R0x_CRG_CRPR_PLLMODE (0x1f << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X49 (0 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X46 (1 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X37 (2 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X20 (3 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X47 (4 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X44 (5 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X36 (6 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X19 (7 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X39 (8 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X38 (9 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X30 (10 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X15 (11 << 0)
-/*
- * DDR2 controller bits
- */
-#define MB86R0x_DDR2_DRCI_DRINI (1 << 15)
-#define MB86R0x_DDR2_DRCI_CKEN (1 << 14)
-#define MB86R0x_DDR2_DRCI_DRCMD (1 << 0)
-#define MB86R0x_DDR2_DRCI_CMD (MB86R0x_DDR2_DRCI_DRINI | \
- MB86R0x_DDR2_DRCI_CKEN | \
- MB86R0x_DDR2_DRCI_DRCMD)
-#define MB86R0x_DDR2_DRCI_INIT (MB86R0x_DDR2_DRCI_DRINI | \
- MB86R0x_DDR2_DRCI_CKEN)
-#define MB86R0x_DDR2_DRCI_NORMAL MB86R0x_DDR2_DRCI_CKEN
-#endif /* MB86R0X_H */
diff --git a/arch/arm/lib/asm-offsets.c b/arch/arm/lib/asm-offsets.c
index b0c26e5..e5bcaea 100644
--- a/arch/arm/lib/asm-offsets.c
+++ b/arch/arm/lib/asm-offsets.c
@@ -15,9 +15,6 @@
#include <common.h>
#include <linux/kbuild.h>
-#if defined(CONFIG_MB86R0x)
-#include <asm/arch/mb86r0x.h>
-#endif
#if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35) \
|| defined(CONFIG_MX51) || defined(CONFIG_MX53)
#include <asm/arch/imx-regs.h>
@@ -27,8 +24,6 @@ int main(void)
{
/*
* TODO : Check if each entry in this file is really necessary.
- * - struct mb86r0x_ddr2
- * - struct mb86r0x_memc
* - struct esdramc_regs
* - struct max_regs
* - struct aips_regs
@@ -40,47 +35,6 @@ int main(void)
* code. Is it better to define the macros directly in headers?
*/
-#if defined(CONFIG_MB86R0x)
- /* ddr2 controller */
- DEFINE(DDR2_DRIC, offsetof(struct mb86r0x_ddr2c, dric));
- DEFINE(DDR2_DRIC1, offsetof(struct mb86r0x_ddr2c, dric1));
- DEFINE(DDR2_DRIC2, offsetof(struct mb86r0x_ddr2c, dric2));
- DEFINE(DDR2_DRCA, offsetof(struct mb86r0x_ddr2c, drca));
- DEFINE(DDR2_DRCM, offsetof(struct mb86r0x_ddr2c, drcm));
- DEFINE(DDR2_DRCST1, offsetof(struct mb86r0x_ddr2c, drcst1));
- DEFINE(DDR2_DRCST2, offsetof(struct mb86r0x_ddr2c, drcst2));
- DEFINE(DDR2_DRCR, offsetof(struct mb86r0x_ddr2c, drcr));
- DEFINE(DDR2_DRCF, offsetof(struct mb86r0x_ddr2c, drcf));
- DEFINE(DDR2_DRASR, offsetof(struct mb86r0x_ddr2c, drasr));
- DEFINE(DDR2_DRIMS, offsetof(struct mb86r0x_ddr2c, drims));
- DEFINE(DDR2_DROS, offsetof(struct mb86r0x_ddr2c, dros));
- DEFINE(DDR2_DRIBSODT1, offsetof(struct mb86r0x_ddr2c, dribsodt1));
- DEFINE(DDR2_DROABA, offsetof(struct mb86r0x_ddr2c, droaba));
- DEFINE(DDR2_DROBS, offsetof(struct mb86r0x_ddr2c, drobs));
-
- /* clock reset generator */
- DEFINE(CRG_CRPR, offsetof(struct mb86r0x_crg, crpr));
- DEFINE(CRG_CRHA, offsetof(struct mb86r0x_crg, crha));
- DEFINE(CRG_CRPA, offsetof(struct mb86r0x_crg, crpa));
- DEFINE(CRG_CRPB, offsetof(struct mb86r0x_crg, crpb));
- DEFINE(CRG_CRHB, offsetof(struct mb86r0x_crg, crhb));
- DEFINE(CRG_CRAM, offsetof(struct mb86r0x_crg, cram));
-
- /* chip control module */
- DEFINE(CCNT_CDCRC, offsetof(struct mb86r0x_ccnt, cdcrc));
-
- /* external bus interface */
- DEFINE(MEMC_MCFMODE0, offsetof(struct mb86r0x_memc, mcfmode[0]));
- DEFINE(MEMC_MCFMODE2, offsetof(struct mb86r0x_memc, mcfmode[2]));
- DEFINE(MEMC_MCFMODE4, offsetof(struct mb86r0x_memc, mcfmode[4]));
- DEFINE(MEMC_MCFTIM0, offsetof(struct mb86r0x_memc, mcftim[0]));
- DEFINE(MEMC_MCFTIM2, offsetof(struct mb86r0x_memc, mcftim[2]));
- DEFINE(MEMC_MCFTIM4, offsetof(struct mb86r0x_memc, mcftim[4]));
- DEFINE(MEMC_MCFAREA0, offsetof(struct mb86r0x_memc, mcfarea[0]));
- DEFINE(MEMC_MCFAREA2, offsetof(struct mb86r0x_memc, mcfarea[2]));
- DEFINE(MEMC_MCFAREA4, offsetof(struct mb86r0x_memc, mcfarea[4]));
-#endif
-
#if defined(CONFIG_MX25)
/* Clock Control Module */
DEFINE(CCM_CCTL, offsetof(struct ccm_regs, cctl));
diff --git a/board/syteco/jadecpu/Kconfig b/board/syteco/jadecpu/Kconfig
deleted file mode 100644
index 6e9392e..0000000
--- a/board/syteco/jadecpu/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_JADECPU
-
-config SYS_BOARD
- default "jadecpu"
-
-config SYS_VENDOR
- default "syteco"
-
-config SYS_SOC
- default "mb86r0x"
-
-config SYS_CONFIG_NAME
- default "jadecpu"
-
-endif
diff --git a/board/syteco/jadecpu/MAINTAINERS b/board/syteco/jadecpu/MAINTAINERS
deleted file mode 100644
index b53e7ca..0000000
--- a/board/syteco/jadecpu/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-JADECPU BOARD
-M: Matthias Weisser <weisserm@arcor.de>
-S: Maintained
-F: board/syteco/jadecpu/
-F: include/configs/jadecpu.h
-F: configs/jadecpu_defconfig
diff --git a/board/syteco/jadecpu/Makefile b/board/syteco/jadecpu/Makefile
deleted file mode 100644
index 7426436..0000000
--- a/board/syteco/jadecpu/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2008
-# Stelian Pop <stelian@popies.net>
-# Lead Tech Design <www.leadtechdesign.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += jadecpu.o
-obj-y += lowlevel_init.o
diff --git a/board/syteco/jadecpu/jadecpu.c b/board/syteco/jadecpu/jadecpu.c
deleted file mode 100644
index 6c60a41..0000000
--- a/board/syteco/jadecpu/jadecpu.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * (c) 2010 Graf-Syteco, Matthias Weisser
- * <weisserm@arcor.de>
- *
- * (C) Copyright 2007, mycable GmbH
- * Carsten Schneider <cs@mycable.de>, Alexander Bigga <ab@mycable.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/mb86r0x.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_init(void)
-{
- struct mb86r0x_ccnt * ccnt = (struct mb86r0x_ccnt *)
- MB86R0x_CCNT_BASE;
-
- /* We select mode 0 for group 2 and mode 1 for group 4 */
- writel(0x00000010, &ccnt->cmux_md);
-
- gd->flags = 0;
- gd->bd->bi_boot_params = PHYS_SDRAM + PHYS_SDRAM_SIZE - 0x10000;
-
- icache_enable();
- dcache_enable();
-
- return 0;
-}
-
-static void setup_display_power(uint32_t pwr_bit, char *pwm_opts,
- unsigned long pwm_base)
-{
- struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *)
- MB86R0x_GPIO_BASE;
- struct mb86r0x_pwm *pwm = (struct mb86r0x_pwm *) pwm_base;
- const char *e;
-
- writel(readl(&gpio->gpdr2) | pwr_bit, &gpio->gpdr2);
-
- e = getenv(pwm_opts);
- if (e != NULL) {
- const char *s;
- uint32_t freq, init;
-
- freq = 0;
- init = 0;
-
- s = strchr(e, 'f');
- if (s != NULL)
- freq = simple_strtol(s + 2, NULL, 0);
-
- s = strchr(e, 'i');
- if (s != NULL)
- init = simple_strtol(s + 2, NULL, 0);
-
- if (freq > 0) {
- writel(CONFIG_MB86R0x_IOCLK / 1000 / freq,
- &pwm->bcr);
- writel(1002, &pwm->tpr);
- writel(1, &pwm->pr);
- writel(init * 10 + 1, &pwm->dr);
- writel(1, &pwm->cr);
- writel(1, &pwm->sr);
- }
- }
-}
-
-int board_late_init(void)
-{
- struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *)
- MB86R0x_GPIO_BASE;
- uint32_t in_word;
-
-#ifdef CONFIG_VIDEO_MB86R0xGDC
- /* Check if we have valid display settings and turn on power if so */
- /* Display 0 */
- if (getenv("gs_dsp_0_param") || getenv("videomode"))
- setup_display_power((1 << 3), "gs_dsp_0_pwm",
- MB86R0x_PWM0_BASE);
-
- /* The corresponding GPIO is always an output */
- writel(readl(&gpio->gpddr2) | (1 << 3), &gpio->gpddr2);
-
- /* Display 1 */
- if (getenv("gs_dsp_1_param") || getenv("videomode1"))
- setup_display_power((1 << 4), "gs_dsp_1_pwm",
- MB86R0x_PWM1_BASE);
-
- /* The corresponding GPIO is always an output */
- writel(readl(&gpio->gpddr2) | (1 << 4), &gpio->gpddr2);
-#endif /* CONFIG_VIDEO_MB86R0xGDC */
-
- /* 5V enable */
- writel(readl(&gpio->gpdr1) & ~(1 << 5), &gpio->gpdr1);
- writel(readl(&gpio->gpddr1) | (1 << 5), &gpio->gpddr1);
-
- /* We have special boot options if told by GPIOs */
- in_word = readl(&gpio->gpdr1);
-
- if ((in_word & 0xC0) == 0xC0) {
- setenv("stdin", "serial");
- setenv("stdout", "serial");
- setenv("stderr", "serial");
- setenv("preboot", "run gs_slow_boot");
- } else if ((in_word & 0xC0) != 0) {
- setenv("stdout", "vga");
- setenv("preboot", "run gs_slow_boot");
- } else {
- setenv("stdin", "serial");
- setenv("stdout", "serial");
- setenv("stderr", "serial");
- if (getenv("gs_devel")) {
- setenv("preboot", "run gs_slow_boot");
- } else {
- setenv("preboot", "run gs_fast_boot");
- }
- }
-
- return 0;
-}
-
-int misc_init_r(void)
-{
- return 0;
-}
-
-/*
- * DRAM configuration
- */
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
- PHYS_SDRAM_SIZE);
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM;
- gd->bd->bi_dram[0].size = gd->ram_size;
-}
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC911X
- rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
- return rc;
-}
diff --git a/board/syteco/jadecpu/lowlevel_init.S b/board/syteco/jadecpu/lowlevel_init.S
deleted file mode 100644
index 9568cec..0000000
--- a/board/syteco/jadecpu/lowlevel_init.S
+++ /dev/null
@@ -1,249 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2007, mycable GmbH
- * Carsten Schneider <cs@mycable.de>, Alexander Bigga <ab@mycable.de>
- *
- * (C) Copyright 2003, ARM Ltd.
- * Philippe Robin, <philippe.robin@arm.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/macro.h>
-#include <asm/arch/mb86r0x.h>
-#include <generated/asm-offsets.h>
-
-/* Set up the platform, once the cpu has been initialized */
-.globl lowlevel_init
-lowlevel_init:
-/*
- * Initialize Clock Reset Generator (CRG)
- */
-
- ldr r0, =MB86R0x_CRG_BASE
-
- /* Not change the initial value that is set by external pin.*/
-WAIT_PLL:
- ldr r2, [r0, #CRG_CRPR] /* Wait for PLLREADY */
- tst r2, #MB86R0x_CRG_CRPR_PLLRDY
- beq WAIT_PLL
-
- /* Set clock gate control */
- ldr r1, =CONFIG_SYS_CRG_CRHA_INIT
- str r1, [r0, #CRG_CRHA]
- ldr r1, =CONFIG_SYS_CRG_CRPA_INIT
- str r1, [r0, #CRG_CRPA]
- ldr r1, =CONFIG_SYS_CRG_CRPB_INIT
- str r1, [r0, #CRG_CRPB]
- ldr r1, =CONFIG_SYS_CRG_CRHB_INIT
- str r1, [r0, #CRG_CRHB]
- ldr r1, =CONFIG_SYS_CRG_CRAM_INIT
- str r1, [r0, #CRG_CRAM]
-
-/*
- * Initialize External Bus Interface
- */
- ldr r0, =MB86R0x_MEMC_BASE
-
- ldr r1, =CONFIG_SYS_MEMC_MCFMODE0_INIT
- str r1, [r0, #MEMC_MCFMODE0]
- ldr r1, =CONFIG_SYS_MEMC_MCFMODE2_INIT
- str r1, [r0, #MEMC_MCFMODE2]
- ldr r1, =CONFIG_SYS_MEMC_MCFMODE4_INIT
- str r1, [r0, #MEMC_MCFMODE4]
-
- ldr r1, =CONFIG_SYS_MEMC_MCFTIM0_INIT
- str r1, [r0, #MEMC_MCFTIM0]
- ldr r1, =CONFIG_SYS_MEMC_MCFTIM2_INIT
- str r1, [r0, #MEMC_MCFTIM2]
- ldr r1, =CONFIG_SYS_MEMC_MCFTIM4_INIT
- str r1, [r0, #MEMC_MCFTIM4]
-
- ldr r1, =CONFIG_SYS_MEMC_MCFAREA0_INIT
- str r1, [r0, #MEMC_MCFAREA0]
- ldr r1, =CONFIG_SYS_MEMC_MCFAREA2_INIT
- str r1, [r0, #MEMC_MCFAREA2]
- ldr r1, =CONFIG_SYS_MEMC_MCFAREA4_INIT
- str r1, [r0, #MEMC_MCFAREA4]
-
-/*
- * Initialize DDR2 Controller
- */
-
- /* Wait for PLL LOCK up time or more */
- wait_timer 20
-
- /*
- * (2) Initialize DDRIF
- */
- ldr r0, =MB86R0x_DDR2_BASE
- ldr r1, =CONFIG_SYS_DDR2_DRIMS_INIT
- strh r1, [r0, #DDR2_DRIMS]
-
- /*
- * (3) Wait for 20MCKPs(120nsec) or more
- */
- wait_timer 20
-
- /*
- * (4) IRESET/IUSRRST release
- */
- ldr r0, =MB86R0x_CCNT_BASE
- ldr r1, =CONFIG_SYS_CCNT_CDCRC_INIT_1
- str r1, [r0, #CCNT_CDCRC]
-
- /*
- * (5) Wait for 20MCKPs(120nsec) or more
- */
- wait_timer 20
-
- /*
- * (6) IDLLRST release
- */
- ldr r0, =MB86R0x_CCNT_BASE
- ldr r1, =CONFIG_SYS_CCNT_CDCRC_INIT_2
- str r1, [r0, #CCNT_CDCRC]
-
- /*
- * (7+8) Wait for 200us(=200000ns) or more (DDR2 Spec)
- */
- wait_timer 33536
-
- /*
- * (9) MCKE ON
- */
- ldr r0, =MB86R0x_DDR2_BASE
- ldr r1, =CONFIG_SYS_DDR2_DRIC1_INIT
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_DRIC2_INIT
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =CONFIG_SYS_DDR2_DRCA_INIT
- strh r1, [r0, #DDR2_DRCA]
- ldr r1, =MB86R0x_DDR2_DRCI_INIT
- strh r1, [r0, #DDR2_DRIC]
-
- /*
- * (10) Initialize SDRAM
- */
-
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 67 /* 400ns wait */
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_1
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_1
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_2
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_2
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_3
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_3
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_4
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_4
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_5
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_5
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 200
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_6
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_6
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_7
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_7
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 18 /* 105ns wait */
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_8
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_8
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- wait_timer 200 /* MRS to OCD: 200clock */
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_9
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_9
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_10
- strh r1, [r0, #DDR2_DRIC1]
- ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_10
- strh r1, [r0, #DDR2_DRIC2]
- ldr r1, =MB86R0x_DDR2_DRCI_CMD
- strh r1, [r0, #DDR2_DRIC]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCM_INIT
- strh r1, [r0, #DDR2_DRCM]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCST1_INIT
- strh r1, [r0, #DDR2_DRCST1]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCST2_INIT
- strh r1, [r0, #DDR2_DRCST2]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCR_INIT
- strh r1, [r0, #DDR2_DRCR]
-
- ldr r1, =CONFIG_SYS_DDR2_DRCF_INIT
- strh r1, [r0, #DDR2_DRCF]
-
- ldr r1, =CONFIG_SYS_DDR2_DRASR_INIT
- strh r1, [r0, #DDR2_DRASR]
-
- /*
- * (11) ODT setting
- */
- ldr r1, =CONFIG_SYS_DDR2_DROBS_INIT
- strh r1, [r0, #DDR2_DROBS]
- ldr r1, =CONFIG_SYS_DDR2_DROABA_INIT
- strh r1, [r0, #DDR2_DROABA]
- ldr r1, =CONFIG_SYS_DDR2_DRIBSODT1_INIT
- strh r1, [r0, #DDR2_DRIBSODT1]
-
- /*
- * (12) Shift to ODTCONT ON (SDRAM side) and DDR2 usual operation mode
- */
- ldr r1, =CONFIG_SYS_DDR2_DROS_INIT
- strh r1, [r0, #DDR2_DROS]
- ldr r1, =MB86R0x_DDR2_DRCI_NORMAL
- strh r1, [r0, #DDR2_DRIC]
-
- mov pc, lr
diff --git a/configs/jadecpu_defconfig b/configs/jadecpu_defconfig
deleted file mode 100644
index 4348e0e..0000000
--- a/configs/jadecpu_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_JADECPU=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index cd51249..fbeb2cd 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+jadecpu arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
imx31_phycore arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
mx31ads arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
icecube_5200 powerpc mpc5xxx 37b608a5 2015-01-23 Wolfgang Denk <wd@denx.de>
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index af2d47b..22a316b 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -32,7 +32,6 @@ obj-$(CONFIG_VIDEO_IMX25LCDC) += imx25lcdc.o videomodes.o
obj-$(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM) += hitachi_tx18d42vm_lcd.o
obj-$(CONFIG_VIDEO_LCD_SSD2828) += ssd2828.o
obj-$(CONFIG_VIDEO_MB862xx) += mb862xx.o videomodes.o
-obj-$(CONFIG_VIDEO_MB86R0xGDC) += mb86r0xgdc.o videomodes.o
obj-$(CONFIG_VIDEO_MX3) += mx3fb.o videomodes.o
obj-$(CONFIG_VIDEO_IPUV3) += mxc_ipuv3_fb.o ipu_common.o ipu_disp.o
obj-$(CONFIG_VIDEO_MXS) += mxsfb.o videomodes.o
diff --git a/drivers/video/mb86r0xgdc.c b/drivers/video/mb86r0xgdc.c
deleted file mode 100644
index bb7a749..0000000
--- a/drivers/video/mb86r0xgdc.c
+++ /dev/null
@@ -1,168 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * mb86r0xgdc.c - Graphic interface for Fujitsu MB86R0x integrated graphic
- * controller.
- */
-
-#include <common.h>
-
-#include <malloc.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <video_fb.h>
-#include "videomodes.h"
-
-/*
- * 4MB (at the end of system RAM)
- */
-#define VIDEO_MEM_SIZE 0x400000
-
-#define FB_SYNC_CLK_INV (1<<16) /* pixel clock inverted */
-
-/*
- * Graphic Device
- */
-static GraphicDevice mb86r0x;
-
-static void dsp_init(struct mb86r0x_gdc_dsp *dsp, char *modestr,
- u32 *videomem)
-{
- struct ctfb_res_modes var_mode;
- u32 dcm1, dcm2, dcm3;
- u16 htp, hdp, hdb, hsp, vtr, vsp, vdp;
- u8 hsw, vsw;
- u32 l2m, l2em, l2oa0, l2da0, l2oa1, l2da1;
- u16 l2dx, l2dy, l2wx, l2wy, l2ww, l2wh;
- unsigned long div;
- int bpp;
-
- bpp = video_get_params(&var_mode, modestr);
-
- if (bpp == 0) {
- var_mode.xres = 640;
- var_mode.yres = 480;
- var_mode.pixclock = 39721; /* 25MHz */
- var_mode.left_margin = 48;
- var_mode.right_margin = 16;
- var_mode.upper_margin = 33;
- var_mode.lower_margin = 10;
- var_mode.hsync_len = 96;
- var_mode.vsync_len = 2;
- var_mode.sync = 0;
- var_mode.vmode = 0;
- bpp = 15;
- }
-
- /* Fill memory with white */
- memset(videomem, 0xFF, var_mode.xres * var_mode.yres * 2);
-
- mb86r0x.winSizeX = var_mode.xres;
- mb86r0x.winSizeY = var_mode.yres;
-
- /* LCD base clock is ~ 660MHZ. We do calculations in kHz */
- div = 660000 / (1000000000L / var_mode.pixclock);
- if (div > 64)
- div = 64;
- if (0 == div)
- div = 1;
-
- dcm1 = (div - 1) << 8;
- dcm2 = 0x00000000;
- if (var_mode.sync & FB_SYNC_CLK_INV)
- dcm3 = 0x00000100;
- else
- dcm3 = 0x00000000;
-
- htp = var_mode.left_margin + var_mode.xres +
- var_mode.hsync_len + var_mode.right_margin;
- hdp = var_mode.xres;
- hdb = var_mode.xres;
- hsp = var_mode.xres + var_mode.right_margin;
- hsw = var_mode.hsync_len;
-
- vsw = var_mode.vsync_len;
- vtr = var_mode.upper_margin + var_mode.yres +
- var_mode.vsync_len + var_mode.lower_margin;
- vsp = var_mode.yres + var_mode.lower_margin;
- vdp = var_mode.yres;
-
- l2m = ((var_mode.yres - 1) << (0)) |
- (((var_mode.xres * 2) / 64) << (16)) |
- ((1) << (31));
-
- l2em = (1 << 0) | (1 << 1);
-
- l2oa0 = mb86r0x.frameAdrs;
- l2da0 = mb86r0x.frameAdrs;
- l2oa1 = mb86r0x.frameAdrs;
- l2da1 = mb86r0x.frameAdrs;
- l2dx = 0;
- l2dy = 0;
- l2wx = 0;
- l2wy = 0;
- l2ww = var_mode.xres;
- l2wh = var_mode.yres - 1;
-
- writel(dcm1, &dsp->dcm1);
- writel(dcm2, &dsp->dcm2);
- writel(dcm3, &dsp->dcm3);
-
- writew(htp, &dsp->htp);
- writew(hdp, &dsp->hdp);
- writew(hdb, &dsp->hdb);
- writew(hsp, &dsp->hsp);
- writeb(hsw, &dsp->hsw);
-
- writeb(vsw, &dsp->vsw);
- writew(vtr, &dsp->vtr);
- writew(vsp, &dsp->vsp);
- writew(vdp, &dsp->vdp);
-
- writel(l2m, &dsp->l2m);
- writel(l2em, &dsp->l2em);
- writel(l2oa0, &dsp->l2oa0);
- writel(l2da0, &dsp->l2da0);
- writel(l2oa1, &dsp->l2oa1);
- writel(l2da1, &dsp->l2da1);
- writew(l2dx, &dsp->l2dx);
- writew(l2dy, &dsp->l2dy);
- writew(l2wx, &dsp->l2wx);
- writew(l2wy, &dsp->l2wy);
- writew(l2ww, &dsp->l2ww);
- writew(l2wh, &dsp->l2wh);
-
- writel(dcm1 | (1 << 18) | (1 << 31), &dsp->dcm1);
-}
-
-void *video_hw_init(void)
-{
- struct mb86r0x_gdc *gdc = (struct mb86r0x_gdc *) MB86R0x_GDC_BASE;
- GraphicDevice *pGD = &mb86r0x;
- char *s;
- u32 *vid;
-
- memset(pGD, 0, sizeof(GraphicDevice));
-
- pGD->gdfIndex = GDF_15BIT_555RGB;
- pGD->gdfBytesPP = 2;
- pGD->memSize = VIDEO_MEM_SIZE;
- pGD->frameAdrs = PHYS_SDRAM + PHYS_SDRAM_SIZE - VIDEO_MEM_SIZE;
-
- vid = (u32 *)pGD->frameAdrs;
-
- s = getenv("videomode");
- if (s != NULL)
- dsp_init(&gdc->dsp0, s, vid);
-
- s = getenv("videomode1");
- if (s != NULL)
- dsp_init(&gdc->dsp1, s, vid);
-
- return pGD;
-}
diff --git a/include/configs/jadecpu.h b/include/configs/jadecpu.h
deleted file mode 100644
index 8175621..0000000
--- a/include/configs/jadecpu.h
+++ /dev/null
@@ -1,273 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * Configuation settings for the jadecpu board
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_MB86R0x
-#define CONFIG_MB86R0x_IOCLK get_bus_freq(0)
-#define CONFIG_SYS_TEXT_BASE 0x10000000
-
-
-#define CONFIG_USE_ARCH_MEMCPY
-#define CONFIG_USE_ARCH_MEMSET
-
-#define MACH_TYPE_JADECPU 2636
-
-#define CONFIG_MACH_TYPE MACH_TYPE_JADECPU
-
-/*
- * Environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "gs_fast_boot=setenv bootdelay 5\0" \
- "gs_slow_boot=setenv bootdelay 10\0" \
- "bootcmd=dcache off; mw.l 0x40000000 0 1024; usb start;" \
- "fatls usb 0; fatload usb 0 0x40000000 jadecpu-init.bin;" \
- "bootelf 0x40000000\0" \
- ""
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * Compressions
- */
-#define CONFIG_LZO
-
-/*
- * Hardware drivers
- */
-
-/*
- * Serial
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1 0xfffe1000 /* UART 0 */
-#define CONFIG_SYS_NS16550_COM2 0xfff50000 /* UART 2 */
-#define CONFIG_SYS_NS16550_COM3 0xfff51000 /* UART 3 */
-#define CONFIG_SYS_NS16550_COM4 0xfff43000 /* UART 4 */
-
-#define CONFIG_CONS_INDEX 4
-
-/*
- * Ethernet
- */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0x02000000
-#define CONFIG_SMC911X_16_BIT
-
-/*
- * Video
- */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_MB86R0xGDC
-#define CONFIG_SYS_WHITE_ON_BLACK
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_VIDEO_BMP_GZIP
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (800*480 + 256*4 + 10*1024)
-#define VIDEO_FB_16BPP_WORD_SWAP
-#define VIDEO_KBD_INIT_FCT 0
-#define VIDEO_TSTC_FCT serial_stub_tstc
-#define VIDEO_GETC_FCT serial_stub_getc
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-#define CONFIG_BOOTP_BOOTPATH 1
-#define CONFIG_BOOTP_GATEWAY 1
-#define CONFIG_BOOTP_HOSTNAME 1
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_CACHE
-
-#define CONFIG_SYS_HUSH_PARSER
-
-/* USB */
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0xFFF81000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mb86r0x"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x40000000 /* Start address of DDRRAM */
-#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR 0x01008000
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE 0x10000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE (128 * 1024)
-#define CONFIG_ENV_SIZE (128 * 1024)
-
-/*
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster */
-
-#define CONFIG_SYS_LOAD_ADDR 0x40000000 /* load address */
-
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM + (512*1024))
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM + PHYS_SDRAM_SIZE)
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_PROMPT "jade> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-
-#define CONFIG_PREBOOT ""
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "boot in %d s\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR "delaygs"
-#define CONFIG_AUTOBOOT_STOP_STR "stopgs"
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (10 << 20)
-#define CONFIG_SYS_MEM_TOP_HIDE (4 << 20)
-
-/*
- * Clock reset generator init
- */
-#define CONFIG_SYS_CRG_CRHA_INIT 0xffff
-#define CONFIG_SYS_CRG_CRPA_INIT 0xffff
-#define CONFIG_SYS_CRG_CRPB_INIT 0xfffe
-#define CONFIG_SYS_CRG_CRHB_INIT 0xffff
-#define CONFIG_SYS_CRG_CRAM_INIT 0xffef
-
-/*
- * Memory controller settings
- */
-#define CONFIG_SYS_MEMC_MCFMODE0_INIT 0x00000001 /* 16bit */
-#define CONFIG_SYS_MEMC_MCFMODE2_INIT 0x00000001 /* 16bit */
-#define CONFIG_SYS_MEMC_MCFMODE4_INIT 0x00000021 /* 16bit, Page*/
-#define CONFIG_SYS_MEMC_MCFTIM0_INIT 0x16191008
-#define CONFIG_SYS_MEMC_MCFTIM2_INIT 0x03061008
-#define CONFIG_SYS_MEMC_MCFTIM4_INIT 0x03061804
-#define CONFIG_SYS_MEMC_MCFAREA0_INIT 0x000000c0 /* 0x0c000000 1MB */
-#define CONFIG_SYS_MEMC_MCFAREA2_INIT 0x00000020 /* 0x02000000 1MB */
-#define CONFIG_SYS_MEMC_MCFAREA4_INIT 0x001f0000 /* 0x10000000 32 MB */
-
-/*
- * DDR2 controller init settings
- */
-#define CONFIG_SYS_DDR2_DRIMS_INIT 0x5555
-#define CONFIG_SYS_CCNT_CDCRC_INIT_1 0x00000002
-#define CONFIG_SYS_CCNT_CDCRC_INIT_2 0x00000003
-#define CONFIG_SYS_DDR2_DRIC1_INIT 0x003f
-#define CONFIG_SYS_DDR2_DRIC2_INIT 0x0000
-#define CONFIG_SYS_DDR2_DRCA_INIT 0xc124 /* 512Mbit DDR2SDRAM x 2 */
-#define CONFIG_SYS_DDR2_DRCM_INIT 0x0032
-#define CONFIG_SYS_DDR2_DRCST1_INIT 0x3418
-#define CONFIG_SYS_DDR2_DRCST2_INIT 0x6e32
-#define CONFIG_SYS_DDR2_DRCR_INIT 0x0141
-#define CONFIG_SYS_DDR2_DRCF_INIT 0x0002
-#define CONFIG_SYS_DDR2_DRASR_INIT 0x0001
-#define CONFIG_SYS_DDR2_DROBS_INIT 0x0001
-#define CONFIG_SYS_DDR2_DROABA_INIT 0x0103
-#define CONFIG_SYS_DDR2_DRIBSODT1_INIT 0x003F
-#define CONFIG_SYS_DDR2_DROS_INIT 0x0001
-
-/*
- * DRAM init sequence
- */
-
-/* PALL Command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_1 0x0017
-#define CONFIG_SYS_DDR2_INIT_DRIC2_1 0x0400
-
-/* EMR(2) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_2 0x0006
-#define CONFIG_SYS_DDR2_INIT_DRIC2_2 0x0000
-
-/* EMR(3) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_3 0x0007
-#define CONFIG_SYS_DDR2_INIT_DRIC2_3 0x0000
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_4 0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_4 0x0000
-
-/* MRS command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_5 0x0004
-#define CONFIG_SYS_DDR2_INIT_DRIC2_5 0x0532
-
-/* PALL command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_6 0x0017
-#define CONFIG_SYS_DDR2_INIT_DRIC2_6 0x0400
-
-/* REF command 1 */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_7 0x000f
-#define CONFIG_SYS_DDR2_INIT_DRIC2_7 0x0000
-
-/* MRS command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_8 0x0004
-#define CONFIG_SYS_DDR2_INIT_DRIC2_8 0x0432
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_9 0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_9 0x0380
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_10 0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_10 0x0002
-
-#endif /* __CONFIG_H */
diff --git a/include/serial.h b/include/serial.h
index 66ed12c..3d2e569 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -29,7 +29,7 @@ extern struct serial_device *default_serial_console(void);
#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_440) || \
- defined(CONFIG_MB86R0x) || defined(CONFIG_MPC5xxx) || \
+ defined(CONFIG_MPC5xxx) || \
defined(CONFIG_MPC83xx) || defined(CONFIG_MPC85xx) || \
defined(CONFIG_MPC86xx) || defined(CONFIG_SYS_SC520) || \
defined(CONFIG_TEGRA) || defined(CONFIG_SYS_COREBOOT) || \
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 4/9] ARM: remove zmx25 board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (2 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 3/9] ARM: remove jadecpu board support Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-23 22:30 ` Fabio Estevam
2015-02-22 15:20 ` [U-Boot] [PATCH v4 5/9] ARM: remove dkb " Masahiro Yamada
` (5 subsequent siblings)
9 siblings, 1 reply; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 5 --
board/syteco/zmx25/Kconfig | 15 ----
board/syteco/zmx25/MAINTAINERS | 6 --
board/syteco/zmx25/Makefile | 9 --
board/syteco/zmx25/lowlevel_init.S | 97 ---------------------
board/syteco/zmx25/zmx25.c | 174 -------------------------------------
configs/zmx25_defconfig | 2 -
doc/README.scrapyard | 1 +
include/configs/zmx25.h | 162 ----------------------------------
9 files changed, 1 insertion(+), 470 deletions(-)
delete mode 100644 board/syteco/zmx25/Kconfig
delete mode 100644 board/syteco/zmx25/MAINTAINERS
delete mode 100644 board/syteco/zmx25/Makefile
delete mode 100644 board/syteco/zmx25/lowlevel_init.S
delete mode 100644 board/syteco/zmx25/zmx25.c
delete mode 100644 configs/zmx25_defconfig
delete mode 100644 include/configs/zmx25.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index b24fb18..7ba9737 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -153,10 +153,6 @@ config TARGET_TX25
select CPU_ARM926EJS
select SUPPORT_SPL
-config TARGET_ZMX25
- bool "Support zmx25"
- select CPU_ARM926EJS
-
config TARGET_APF27
bool "Support apf27"
select CPU_ARM926EJS
@@ -839,7 +835,6 @@ source "board/st-ericsson/snowball/Kconfig"
source "board/st-ericsson/u8500/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/sunxi/Kconfig"
-source "board/syteco/zmx25/Kconfig"
source "board/tbs/tbs2910/Kconfig"
source "board/ti/am335x/Kconfig"
source "board/ti/am43xx/Kconfig"
diff --git a/board/syteco/zmx25/Kconfig b/board/syteco/zmx25/Kconfig
deleted file mode 100644
index 59a415d..0000000
--- a/board/syteco/zmx25/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_ZMX25
-
-config SYS_BOARD
- default "zmx25"
-
-config SYS_VENDOR
- default "syteco"
-
-config SYS_SOC
- default "mx25"
-
-config SYS_CONFIG_NAME
- default "zmx25"
-
-endif
diff --git a/board/syteco/zmx25/MAINTAINERS b/board/syteco/zmx25/MAINTAINERS
deleted file mode 100644
index 90f9fab..0000000
--- a/board/syteco/zmx25/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ZMX25 BOARD
-M: Matthias Weisser <weisserm@arcor.de>
-S: Maintained
-F: board/syteco/zmx25/
-F: include/configs/zmx25.h
-F: configs/zmx25_defconfig
diff --git a/board/syteco/zmx25/Makefile b/board/syteco/zmx25/Makefile
deleted file mode 100644
index d5edb48..0000000
--- a/board/syteco/zmx25/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (c) 2010 Graf-Syteco, Matthias Weisser
-# <weisserm@arcor.de>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += zmx25.o
-obj-y += lowlevel_init.o
diff --git a/board/syteco/zmx25/lowlevel_init.S b/board/syteco/zmx25/lowlevel_init.S
deleted file mode 100644
index 5eccf09..0000000
--- a/board/syteco/zmx25/lowlevel_init.S
+++ /dev/null
@@ -1,97 +0,0 @@
-/*
- * (C) Copyright 2011
- * Matthias Weisser <weisserm@arcor.de>
- *
- * (C) Copyright 2009 DENX Software Engineering
- * Author: John Rigby <jrigby@gmail.com>
- *
- * Based on U-Boot and RedBoot sources for several different i.mx
- * platforms.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm/macro.h>
-#include <asm/arch/macro.h>
-#include <asm/arch/imx-regs.h>
-#include <generated/asm-offsets.h>
-
-/*
- * clocks
- */
-.macro init_clocks
-
- /* disable clock output */
- write32 IMX_CCM_BASE + CCM_MCR, 0x00000000
- write32 IMX_CCM_BASE + CCM_CCTL, 0x50030000
-
- /*
- * enable all implemented clocks in all three
- * clock control registers
- */
- write32 IMX_CCM_BASE + CCM_CGCR0, 0x1fffffff
- write32 IMX_CCM_BASE + CCM_CGCR1, 0xffffffff
- write32 IMX_CCM_BASE + CCM_CGCR2, 0xfffff
-
- /* Devide NAND clock by 32 */
- write32 IMX_CCM_BASE + CCM_PCDR2, 0x0101011F
-.endm
-
-/*
- * sdram controller init
- */
-.macro init_lpddr
- ldr r0, =IMX_ESDRAMC_BASE
- ldr r2, =IMX_SDRAM_BANK0_BASE
-
- /*
- * reset SDRAM controller
- * then wait for initialization to complete
- */
- ldr r1, =(1 << 1) | (1 << 2)
- str r1, [r0, #ESDRAMC_ESDMISC]
-1: ldr r3, [r0, #ESDRAMC_ESDMISC]
- tst r3, #(1 << 31)
- beq 1b
- ldr r1, =(1 << 2)
- str r1, [r0, #ESDRAMC_ESDMISC]
-
- ldr r1, =0x002a7420
- str r1, [r0, #ESDRAMC_ESDCFG0]
-
- /* control | precharge */
- ldr r1, =0x92216008
- str r1, [r0, #ESDRAMC_ESDCTL0]
- /* dram command encoded in address */
- str r1, [r2, #0x400]
-
- /* auto refresh */
- ldr r1, =0xa2216008
- str r1, [r0, #ESDRAMC_ESDCTL0]
- /* read dram twice to auto refresh */
- ldr r3, [r2]
- ldr r3, [r2]
-
- /* control | load mode */
- ldr r1, =0xb2216008
- str r1, [r0, #ESDRAMC_ESDCTL0]
-
- /* mode register of lpddram */
- strb r1, [r2, #0x33]
-
- /* extended mode register of lpddrram */
- ldr r2, =0x81000000
- strb r1, [r2]
-
- /* control | normal */
- ldr r1, =0x82216008
- str r1, [r0, #ESDRAMC_ESDCTL0]
-.endm
-
-.globl lowlevel_init
-lowlevel_init:
- init_aips
- init_max
- init_clocks
- init_lpddr
- mov pc, lr
diff --git a/board/syteco/zmx25/zmx25.c b/board/syteco/zmx25/zmx25.c
deleted file mode 100644
index bdbf02a..0000000
--- a/board/syteco/zmx25/zmx25.c
+++ /dev/null
@@ -1,174 +0,0 @@
-/*
- * (c) 2011 Graf-Syteco, Matthias Weisser
- * <weisserm@arcor.de>
- *
- * Based on tx25.c:
- * (C) Copyright 2009 DENX Software Engineering
- * Author: John Rigby <jrigby@gmail.com>
- *
- * Based on imx27lite.c:
- * Copyright (C) 2008,2009 Eric Jarrige <jorasse@users.sourceforge.net>
- * Copyright (C) 2009 Ilya Yanok <yanok@emcraft.com>
- * And:
- * RedBoot tx25_misc.c Copyright (C) 2009 Red Hat
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux-mx25.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init()
-{
- static const iomux_v3_cfg_t sdhc1_pads[] = {
- NEW_PAD_CTRL(MX25_PAD_SD1_CMD__SD1_CMD, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_CLK__SD1_CLK, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA0__SD1_DATA0, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA1__SD1_DATA1, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA2__SD1_DATA2, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA3__SD1_DATA3, NO_PAD_CTRL),
- };
-
- static const iomux_v3_cfg_t dig_out_pads[] = {
- MX25_PAD_CSI_D8__GPIO_1_7, /* Ouput 1 Ctrl */
- MX25_PAD_CSI_D7__GPIO_1_6, /* Ouput 2 Ctrl */
- NEW_PAD_CTRL(MX25_PAD_CSI_D6__GPIO_1_31, 0), /* Ouput 1 Stat */
- NEW_PAD_CTRL(MX25_PAD_CSI_D5__GPIO_1_30, 0), /* Ouput 2 Stat */
- };
-
- static const iomux_v3_cfg_t led_pads[] = {
- MX25_PAD_CSI_D9__GPIO_4_21,
- MX25_PAD_CSI_D4__GPIO_1_29,
- };
-
- static const iomux_v3_cfg_t can_pads[] = {
- NEW_PAD_CTRL(MX25_PAD_GPIO_A__CAN1_TX, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_GPIO_B__CAN1_RX, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_GPIO_C__CAN2_TX, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_GPIO_D__CAN2_RX, NO_PAD_CTRL),
- };
-
- static const iomux_v3_cfg_t i2c3_pads[] = {
- MX25_PAD_CSPI1_SS1__I2C3_DAT,
- MX25_PAD_GPIO_E__I2C3_CLK,
- };
-
- icache_enable();
-
- /* Setup of core voltage selection pin to run at 1.4V */
- imx_iomux_v3_setup_pad(MX25_PAD_EXT_ARMCLK__GPIO_3_15); /* VCORE */
- gpio_direction_output(IMX_GPIO_NR(3, 15), 1);
-
- /* Setup of SD card pins*/
- imx_iomux_v3_setup_multiple_pads(sdhc1_pads, ARRAY_SIZE(sdhc1_pads));
-
- /* Setup of digital output for USB power and OC */
- imx_iomux_v3_setup_pad(MX25_PAD_CSI_D3__GPIO_1_28); /* USB Power */
- gpio_direction_output(IMX_GPIO_NR(1, 28), 1);
-
- imx_iomux_v3_setup_pad(MX25_PAD_CSI_D2__GPIO_1_27); /* USB OC */
- gpio_direction_input(IMX_GPIO_NR(1, 18));
-
- /* Setup of digital output control pins */
- imx_iomux_v3_setup_multiple_pads(dig_out_pads,
- ARRAY_SIZE(dig_out_pads));
-
- /* Switch both output drivers off */
- gpio_direction_output(IMX_GPIO_NR(1, 7), 0);
- gpio_direction_output(IMX_GPIO_NR(1, 6), 0);
-
- /* Setup of key input pin */
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX25_PAD_KPP_ROW0__GPIO_2_29, 0));
- gpio_direction_input(IMX_GPIO_NR(2, 29));
-
- /* Setup of status LED outputs */
- imx_iomux_v3_setup_multiple_pads(led_pads, ARRAY_SIZE(led_pads));
-
- /* Switch both LEDs off */
- gpio_direction_output(IMX_GPIO_NR(4, 21), 0);
- gpio_direction_output(IMX_GPIO_NR(1, 29), 0);
-
- /* Setup of CAN1 and CAN2 signals */
- imx_iomux_v3_setup_multiple_pads(can_pads, ARRAY_SIZE(can_pads));
-
- /* Setup of I2C3 signals */
- imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads));
-
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
- return 0;
-}
-
-int board_late_init(void)
-{
- const char *e;
-
-#ifdef CONFIG_FEC_MXC
-/*
- * FIXME: need to revisit this
- * The original code enabled PUE and 100-k pull-down without PKE, so the right
- * value here is likely:
- * 0 for no pull
- * or:
- * PAD_CTL_PUS_100K_DOWN for 100-k pull-down
- */
-#define FEC_OUT_PAD_CTRL 0
-
- static const iomux_v3_cfg_t fec_pads[] = {
- MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
- MX25_PAD_FEC_RX_DV__FEC_RX_DV,
- MX25_PAD_FEC_RDATA0__FEC_RDATA0,
- NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL),
- MX25_PAD_FEC_MDIO__FEC_MDIO,
- MX25_PAD_FEC_RDATA1__FEC_RDATA1,
- NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL),
-
- MX25_PAD_UPLL_BYPCLK__GPIO_3_16, /* LAN-RESET */
- MX25_PAD_UART2_CTS__FEC_RX_ER, /* FEC_RX_ERR */
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-
- /* assert PHY reset (low) */
- gpio_direction_output(IMX_GPIO_NR(3, 16), 0);
-
- udelay(5000);
-
- /* deassert PHY reset */
- gpio_set_value(IMX_GPIO_NR(3, 16), 1);
-
- udelay(5000);
-#endif
-
- e = getenv("gs_base_board");
- if (e != NULL) {
- if (strcmp(e, "G283") == 0) {
- int key = gpio_get_value(IMX_GPIO_NR(2, 29));
-
- if (key) {
- /* Switch on both LEDs to inidcate boot mode */
- gpio_set_value(IMX_GPIO_NR(1, 29), 0);
- gpio_set_value(IMX_GPIO_NR(4, 21), 0);
-
- setenv("preboot", "run gs_slow_boot");
- } else
- setenv("preboot", "run gs_fast_boot");
- }
- }
-
- return 0;
-}
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
- PHYS_SDRAM_SIZE);
- return 0;
-}
diff --git a/configs/zmx25_defconfig b/configs/zmx25_defconfig
deleted file mode 100644
index 80a66d0..0000000
--- a/configs/zmx25_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_ZMX25=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index fbeb2cd..b24bfea 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+zmx25 arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
jadecpu arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
imx31_phycore arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
mx31ads arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h
deleted file mode 100644
index 356ac88..0000000
--- a/include/configs/zmx25.h
+++ /dev/null
@@ -1,162 +0,0 @@
-/*
- * (c) 2011 Graf-Syteco, Matthias Weisser
- * <weisserm@arcor.de>
- *
- * Configuation settings for the zmx25 board
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_MX25
-#define CONFIG_SYS_TEXT_BASE 0xA0000000
-
-#define CONFIG_SYS_TIMER_RATE 32768
-#define CONFIG_SYS_TIMER_COUNTER \
- (&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
-
-#define CONFIG_MACH_TYPE MACH_TYPE_ZMX25
-/*
- * Environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "gs_fast_boot=setenv bootdelay 5\0" \
- "gs_slow_boot=setenv bootdelay 10\0" \
- "bootcmd=dcache off; mw.l 0x81000000 0 1024; usb start;" \
- "fatls usb 0; fatload usb 0 0x81000000 zmx25-init.bin;" \
- "bootm 0x81000000; bootelf 0x81000000\0"
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * Compressions
- */
-#define CONFIG_LZO
-
-/*
- * Hardware drivers
- */
-
-/*
- * GPIO
- */
-#define CONFIG_MXC_GPIO
-
-/*
- * Serial
- */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART2_BASE
-#define CONFIG_CONS_INDEX 1 /* use UART2 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-
-/*
- * Ethernet
- */
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_MXC_PHYADDR 0x00
-#define CONFIG_MII
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_CACHE
-
-/*
- * Additional command
- */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_USB
-
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * USB
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_MXC
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORT 1
-#define CONFIG_MXC_USB_PORTSC MXC_EHCI_MODE_SERIAL
-#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
-
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x80000000 /* start address of LPDDRRAM */
-#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR 0x78020000 /* end of internal SRAM */
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE 0xA0000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE (128 * 1024)
-#define CONFIG_ENV_SIZE (128 * 1024)
-
-/*
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* ~10x faster */
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
-
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM + (512*1024))
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM + PHYS_SDRAM_SIZE)
-
-#define CONFIG_SYS_PROMPT "zmx25> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-
-#define CONFIG_PREBOOT ""
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "boot in %d s\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR "delaygs"
-#define CONFIG_AUTOBOOT_STOP_STR "stopgs"
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (0x400000 - 0x8000)
-
-#endif /* __CONFIG_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 5/9] ARM: remove dkb board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (3 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 4/9] ARM: remove zmx25 " Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 6/9] ARM: remove cm4008 and cm41xx " Masahiro Yamada
` (4 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Lei Wen <leiwen@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 5 -
arch/arm/cpu/arm926ejs/Makefile | 1 -
arch/arm/cpu/arm926ejs/pantheon/Makefile | 9 --
arch/arm/cpu/arm926ejs/pantheon/cpu.c | 85 -----------
arch/arm/cpu/arm926ejs/pantheon/dram.c | 117 ---------------
arch/arm/cpu/arm926ejs/pantheon/timer.c | 201 --------------------------
arch/arm/include/asm/arch-pantheon/config.h | 53 -------
arch/arm/include/asm/arch-pantheon/cpu.h | 77 ----------
arch/arm/include/asm/arch-pantheon/gpio.h | 0
arch/arm/include/asm/arch-pantheon/mfp.h | 39 -----
arch/arm/include/asm/arch-pantheon/pantheon.h | 38 -----
board/Marvell/dkb/Kconfig | 15 --
board/Marvell/dkb/MAINTAINERS | 6 -
board/Marvell/dkb/Makefile | 9 --
board/Marvell/dkb/dkb.c | 85 -----------
configs/dkb_defconfig | 2 -
doc/README.scrapyard | 1 +
include/configs/dkb.h | 51 -------
18 files changed, 1 insertion(+), 793 deletions(-)
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
delete mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
delete mode 100644 arch/arm/include/asm/arch-pantheon/config.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/gpio.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
delete mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
delete mode 100644 board/Marvell/dkb/Kconfig
delete mode 100644 board/Marvell/dkb/MAINTAINERS
delete mode 100644 board/Marvell/dkb/Makefile
delete mode 100644 board/Marvell/dkb/dkb.c
delete mode 100644 configs/dkb_defconfig
delete mode 100644 include/configs/dkb.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 7ba9737..32d89e1 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -219,10 +219,6 @@ config ORION5X
bool "Marvell Orion"
select CPU_ARM926EJS
-config TARGET_DKB
- bool "Support dkb"
- select CPU_ARM926EJS
-
config TARGET_SPEAR300
bool "Support spear300"
select CPU_ARM926EJS
@@ -746,7 +742,6 @@ source "board/BuR/tseries/Kconfig"
source "board/CarMediaLab/flea3/Kconfig"
source "board/Marvell/aspenite/Kconfig"
source "board/Marvell/db-mv784mp-gp/Kconfig"
-source "board/Marvell/dkb/Kconfig"
source "board/Marvell/gplugd/Kconfig"
source "board/altera/socfpga/Kconfig"
source "board/armadeus/apf27/Kconfig"
diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile
index ac23116..63fa159 100644
--- a/arch/arm/cpu/arm926ejs/Makefile
+++ b/arch/arm/cpu/arm926ejs/Makefile
@@ -19,5 +19,4 @@ obj-$(if $(filter lpc32xx,$(SOC)),y) += lpc32xx/
obj-$(CONFIG_MX25) += mx25/
obj-$(CONFIG_MX27) += mx27/
obj-$(if $(filter mxs,$(SOC)),y) += mxs/
-obj-$(CONFIG_PANTHEON) += pantheon/
obj-$(if $(filter spear,$(SOC)),y) += spear/
diff --git a/arch/arm/cpu/arm926ejs/pantheon/Makefile b/arch/arm/cpu/arm926ejs/pantheon/Makefile
deleted file mode 100644
index 988341f..0000000
--- a/arch/arm/cpu/arm926ejs/pantheon/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2011
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Lei Wen <leiwen@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = cpu.o timer.o dram.o
diff --git a/arch/arm/cpu/arm926ejs/pantheon/cpu.c b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
deleted file mode 100644
index 4e2a177..0000000
--- a/arch/arm/cpu/arm926ejs/pantheon/cpu.c
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/pantheon.h>
-
-#define UARTCLK14745KHZ (APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1))
-#define SET_MRVL_ID (1<<8)
-#define L2C_RAM_SEL (1<<4)
-
-int arch_cpu_init(void)
-{
- u32 val;
- struct panthcpu_registers *cpuregs =
- (struct panthcpu_registers*) PANTHEON_CPU_BASE;
-
- struct panthapb_registers *apbclkres =
- (struct panthapb_registers*) PANTHEON_APBC_BASE;
-
- struct panthmpmu_registers *mpmu =
- (struct panthmpmu_registers*) PANTHEON_MPMU_BASE;
-
- struct panthapmu_registers *apmu =
- (struct panthapmu_registers *) PANTHEON_APMU_BASE;
-
- /* set SEL_MRVL_ID bit in PANTHEON_CPU_CONF register */
- val = readl(&cpuregs->cpu_conf);
- val = val | SET_MRVL_ID;
- writel(val, &cpuregs->cpu_conf);
-
- /* Turn on clock gating (PMUM_CCGR) */
- writel(0xFFFFFFFF, &mpmu->ccgr);
-
- /* Turn on clock gating (PMUM_ACGR) */
- writel(0xFFFFFFFF, &mpmu->acgr);
-
- /* Turn on uart2 clock */
- writel(UARTCLK14745KHZ, &apbclkres->uart0);
-
- /* Enable GPIO clock */
- writel(APBC_APBCLK, &apbclkres->gpio);
-
-#ifdef CONFIG_I2C_MV
- /* Enable I2C clock */
- writel(APBC_RST | APBC_FNCLK | APBC_APBCLK, &apbclkres->twsi);
- writel(APBC_FNCLK | APBC_APBCLK, &apbclkres->twsi);
-#endif
-
-#ifdef CONFIG_MV_SDHCI
- /* Enable mmc clock */
- writel(APMU_PERI_CLK | APMU_AXI_CLK | APMU_PERI_RST | APMU_AXI_RST,
- &apmu->sd1);
- writel(APMU_PERI_CLK | APMU_AXI_CLK | APMU_PERI_RST | APMU_AXI_RST,
- &apmu->sd3);
-#endif
-
- icache_enable();
-
- return 0;
-}
-
-#if defined(CONFIG_DISPLAY_CPUINFO)
-int print_cpuinfo(void)
-{
- u32 id;
- struct panthcpu_registers *cpuregs =
- (struct panthcpu_registers*) PANTHEON_CPU_BASE;
-
- id = readl(&cpuregs->chip_id);
- printf("SoC: PANTHEON 88AP%X-%X\n", (id & 0xFFF), (id >> 0x10));
- return 0;
-}
-#endif
-
-#ifdef CONFIG_I2C_MV
-void i2c_clk_enable(void)
-{
-}
-#endif
diff --git a/arch/arm/cpu/arm926ejs/pantheon/dram.c b/arch/arm/cpu/arm926ejs/pantheon/dram.c
deleted file mode 100644
index f77e3d0..0000000
--- a/arch/arm/cpu/arm926ejs/pantheon/dram.c
+++ /dev/null
@@ -1,117 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>,
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/pantheon.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Pantheon DRAM controller supports upto 8 banks
- * for chip select 0 and 1
- */
-
-/*
- * DDR Memory Control Registers
- * Refer Datasheet 4.4
- */
-struct panthddr_map_registers {
- u32 cs; /* Memory Address Map Register -CS */
- u32 pad[3];
-};
-
-struct panthddr_registers {
- u8 pad[0x100 - 0x000];
- struct panthddr_map_registers mmap[2];
-};
-
-/*
- * panth_sdram_base - reads SDRAM Base Address Register
- */
-u32 panth_sdram_base(int chip_sel)
-{
- struct panthddr_registers *ddr_regs =
- (struct panthddr_registers *)PANTHEON_DRAM_BASE;
- u32 result = 0;
- u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
-
- if (!CS_valid)
- return 0;
-
- result = readl(&ddr_regs->mmap[chip_sel].cs) & 0xFF800000;
- return result;
-}
-
-/*
- * panth_sdram_size - reads SDRAM size
- */
-u32 panth_sdram_size(int chip_sel)
-{
- struct panthddr_registers *ddr_regs =
- (struct panthddr_registers *)PANTHEON_DRAM_BASE;
- u32 result = 0;
- u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
-
- if (!CS_valid)
- return 0;
-
- result = readl(&ddr_regs->mmap[chip_sel].cs);
- result = (result >> 16) & 0xF;
- if (result < 0x7) {
- printf("Unknown DRAM Size\n");
- return -1;
- } else {
- return ((0x8 << (result - 0x7)) * 1024 * 1024);
- }
-}
-
-#ifndef CONFIG_SYS_BOARD_DRAM_INIT
-int dram_init(void)
-{
- int i;
-
- gd->ram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
- gd->bd->bi_dram[i].start = panth_sdram_base(i);
- gd->bd->bi_dram[i].size = panth_sdram_size(i);
- /*
- * It is assumed that all memory banks are consecutive
- * and without gaps.
- * If the gap is found, ram_size will be reported for
- * consecutive memory only
- */
- if (gd->bd->bi_dram[i].start != gd->ram_size)
- break;
-
- gd->ram_size += gd->bd->bi_dram[i].size;
-
- }
-
- for (; i < CONFIG_NR_DRAM_BANKS; i++) {
- /*
- * If above loop terminated prematurely, we need to set
- * remaining banks' start address & size as 0. Otherwise other
- * u-boot functions and Linux kernel gets wrong values which
- * could result in crash
- */
- gd->bd->bi_dram[i].start = 0;
- gd->bd->bi_dram[i].size = 0;
- }
- return 0;
-}
-
-/*
- * If this function is not defined here,
- * board.c alters dram bank zero configuration defined above.
- */
-void dram_init_banksize(void)
-{
- dram_init();
-}
-#endif /* CONFIG_SYS_BOARD_DRAM_INIT */
diff --git a/arch/arm/cpu/arm926ejs/pantheon/timer.c b/arch/arm/cpu/arm926ejs/pantheon/timer.c
deleted file mode 100644
index 6382d3b..0000000
--- a/arch/arm/cpu/arm926ejs/pantheon/timer.c
+++ /dev/null
@@ -1,201 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/pantheon.h>
-
-/*
- * Timer registers
- * Refer 6.2.9 in Datasheet
- */
-struct panthtmr_registers {
- u32 clk_ctrl; /* Timer clk control reg */
- u32 match[9]; /* Timer match registers */
- u32 count[3]; /* Timer count registers */
- u32 status[3];
- u32 ie[3];
- u32 preload[3]; /* Timer preload value */
- u32 preload_ctrl[3];
- u32 wdt_match_en;
- u32 wdt_match_r;
- u32 wdt_val;
- u32 wdt_sts;
- u32 icr[3];
- u32 wdt_icr;
- u32 cer; /* Timer count enable reg */
- u32 cmr;
- u32 ilr[3];
- u32 wcr;
- u32 wfar;
- u32 wsar;
- u32 cvwr[3];
-};
-
-#define TIMER 0 /* Use TIMER 0 */
-/* Each timer has 3 match registers */
-#define MATCH_CMP(x) ((3 * TIMER) + x)
-#define TIMER_LOAD_VAL 0xffffffff
-#define COUNT_RD_REQ 0x1
-
-DECLARE_GLOBAL_DATA_PTR;
-/* Using gd->arch.tbu from timestamp and gd->arch.tbl for lastdec */
-
-/*
- * For preventing risk of instability in reading counter value,
- * first set read request to register cvwr and then read same
- * register after it captures counter value.
- */
-ulong read_timer(void)
-{
- struct panthtmr_registers *panthtimers =
- (struct panthtmr_registers *) PANTHEON_TIMER_BASE;
- volatile int loop=100;
- ulong val;
-
- writel(COUNT_RD_REQ, &panthtimers->cvwr);
- while (loop--)
- val = readl(&panthtimers->cvwr);
-
- /*
- * This stop gcc complain and prevent loop mistake init to 0
- */
- val = readl(&panthtimers->cvwr);
-
- return val;
-}
-
-ulong get_timer_masked(void)
-{
- ulong now = read_timer();
-
- if (now >= gd->arch.tbl) {
- /* normal mode */
- gd->arch.tbu += now - gd->arch.tbl;
- } else {
- /* we have an overflow ... */
- gd->arch.tbu += now + TIMER_LOAD_VAL - gd->arch.tbl;
- }
- gd->arch.tbl = now;
-
- return gd->arch.tbu;
-}
-
-ulong get_timer(ulong base)
-{
- return ((get_timer_masked() / (CONFIG_SYS_HZ_CLOCK / 1000)) -
- base);
-}
-
-void __udelay(unsigned long usec)
-{
- ulong delayticks;
- ulong endtime;
-
- delayticks = (usec * (CONFIG_SYS_HZ_CLOCK / 1000000));
- endtime = get_timer_masked() + delayticks;
-
- while (get_timer_masked() < endtime)
- ;
-}
-
-/*
- * init the Timer
- */
-int timer_init(void)
-{
- struct panthapb_registers *apb1clkres =
- (struct panthapb_registers *) PANTHEON_APBC_BASE;
- struct panthtmr_registers *panthtimers =
- (struct panthtmr_registers *) PANTHEON_TIMER_BASE;
-
- /* Enable Timer clock@3.25 MHZ */
- writel(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(3), &apb1clkres->timers);
-
- /* load value into timer */
- writel(0x0, &panthtimers->clk_ctrl);
- /* Use Timer 0 Match Resiger 0 */
- writel(TIMER_LOAD_VAL, &panthtimers->match[MATCH_CMP(0)]);
- /* Preload value is 0 */
- writel(0x0, &panthtimers->preload[TIMER]);
- /* Enable match comparator 0 for Timer 0 */
- writel(0x1, &panthtimers->preload_ctrl[TIMER]);
-
- /* Enable timer 0 */
- writel(0x1, &panthtimers->cer);
- /* init the gd->arch.tbu and gd->arch.tbl value */
- gd->arch.tbl = read_timer();
- gd->arch.tbu = 0;
-
- return 0;
-}
-
-#define MPMU_APRR_WDTR (1<<4)
-#define TMR_WFAR 0xbaba /* WDT Register First key */
-#define TMP_WSAR 0xeb10 /* WDT Register Second key */
-
-/*
- * This function uses internal Watchdog Timer
- * based reset mechanism.
- * Steps to write watchdog registers (protected access)
- * 1. Write key value to TMR_WFAR reg.
- * 2. Write key value to TMP_WSAR reg.
- * 3. Perform write operation.
- */
-void reset_cpu (unsigned long ignored)
-{
- struct panthmpmu_registers *mpmu =
- (struct panthmpmu_registers *) PANTHEON_MPMU_BASE;
- struct panthtmr_registers *panthtimers =
- (struct panthtmr_registers *) PANTHEON_WD_TIMER_BASE;
- u32 val;
-
- /* negate hardware reset to the WDT after system reset */
- val = readl(&mpmu->aprr);
- val = val | MPMU_APRR_WDTR;
- writel(val, &mpmu->aprr);
-
- /* reset/enable WDT clock */
- writel(APBC_APBCLK, &mpmu->wdtpcr);
-
- /* clear previous WDT status */
- writel(TMR_WFAR, &panthtimers->wfar);
- writel(TMP_WSAR, &panthtimers->wsar);
- writel(0, &panthtimers->wdt_sts);
-
- /* set match counter */
- writel(TMR_WFAR, &panthtimers->wfar);
- writel(TMP_WSAR, &panthtimers->wsar);
- writel(0xf, &panthtimers->wdt_match_r);
-
- /* enable WDT reset */
- writel(TMR_WFAR, &panthtimers->wfar);
- writel(TMP_WSAR, &panthtimers->wsar);
- writel(0x3, &panthtimers->wdt_match_en);
-
- /*enable functional WDT clock */
- writel(APBC_APBCLK | APBC_FNCLK, &mpmu->wdtpcr);
-}
-
-/*
- * This function is derived from PowerPC code (read timebase as long long).
- * On ARM it just returns the timer value.
- */
-unsigned long long get_ticks(void)
-{
- return get_timer(0);
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk (void)
-{
- return (ulong)CONFIG_SYS_HZ;
-}
diff --git a/arch/arm/include/asm/arch-pantheon/config.h b/arch/arm/include/asm/arch-pantheon/config.h
deleted file mode 100644
index 1eed7b1..0000000
--- a/arch/arm/include/asm/arch-pantheon/config.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _PANTHEON_CONFIG_H
-#define _PANTHEON_CONFIG_H
-
-#include <asm/arch/pantheon.h>
-
-/* default Dcache Line length for pantheon */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
-#define CONFIG_SYS_TCLK (14745600) /* NS16550 clk config */
-#define CONFIG_SYS_HZ_CLOCK (3250000) /* Timer Freq. 3.25MHZ */
-#define CONFIG_MARVELL_MFP /* Enable mvmfp driver */
-#define MV_MFPR_BASE PANTHEON_MFPR_BASE
-#define MV_UART_CONSOLE_BASE PANTHEON_UART1_BASE
-#define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register
- represents UART Unit Enable */
-/*
- * I2C definition
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MV 1
-#define CONFIG_MV_I2C_REG 0xd4011000
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 0
-#define CONFIG_SYS_I2C_SLAVE 0xfe
-#endif
-
-/*
- * MMC definition
- */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT 1
-#define CONFIG_MMC 1
-#define CONFIG_GENERIC_MMC 1
-#define CONFIG_SDHCI 1
-#define CONFIG_MMC_SDHCI_IO_ACCESSORS 1
-#define CONFIG_SYS_MMC_MAX_BLK_COUNT 0x1000
-#define CONFIG_MMC_SDMA 1
-#define CONFIG_MV_SDHCI 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_EFI_PARTITION 1
-#define CONFIG_SYS_MMC_NUM 2
-#define CONFIG_SYS_MMC_BASE {0xD4280000, 0xd4281000}
-#endif
-
-#endif /* _PANTHEON_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-pantheon/cpu.h b/arch/arm/include/asm/arch-pantheon/cpu.h
deleted file mode 100644
index 3ccdf8a..0000000
--- a/arch/arm/include/asm/arch-pantheon/cpu.h
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _PANTHEON_CPU_H
-#define _PANTHEON_CPU_H
-
-#include <asm/io.h>
-#include <asm/system.h>
-
-/*
- * Main Power Management (MPMU) Registers
- * Refer Register Datasheet 9.1
- */
-struct panthmpmu_registers {
- u8 pad0[0x0024];
- u32 ccgr; /*0x0024*/
- u8 pad1[0x0200 - 0x024 - 4];
- u32 wdtpcr; /*0x0200*/
- u8 pad2[0x1020 - 0x200 - 4];
- u32 aprr; /*0x1020*/
- u32 acgr; /*0x1024*/
-};
-
-/*
- * Application Power Management (APMU) Registers
- * Refer Register Datasheet 9.2
- */
-struct panthapmu_registers {
- u8 pad0[0x0054];
- u32 sd1; /*0x0054*/
- u8 pad1[0x00e0 - 0x054 - 4];
- u32 sd3; /*0x00e0*/
-};
-
-/*
- * APB Clock Reset/Control Registers
- * Refer Register Datasheet 6.14
- */
-struct panthapb_registers {
- u32 uart0; /*0x000*/
- u32 uart1; /*0x004*/
- u32 gpio; /*0x008*/
- u8 pad0[0x02c - 0x08 - 4];
- u32 twsi; /*0x02c*/
- u8 pad1[0x034 - 0x2c - 4];
- u32 timers; /*0x034*/
-};
-
-/*
- * CPU Interface Registers
- * Refer Register Datasheet 4.3
- */
-struct panthcpu_registers {
- u32 chip_id; /* Chip Id Reg */
- u32 pad;
- u32 cpu_conf; /* CPU Conf Reg */
- u32 pad1;
- u32 cpu_sram_spd; /* CPU SRAM Speed Reg */
- u32 pad2;
- u32 cpu_l2c_spd; /* CPU L2cache Speed Conf */
- u32 mcb_conf; /* MCB Conf Reg */
- u32 sys_boot_ctl; /* Sytem Boot Control */
-};
-
-/*
- * Functions
- */
-u32 panth_sdram_base(int);
-u32 panth_sdram_size(int);
-int mv_sdh_init(u32 regbase, u32 max_clk, u32 min_clk, u32 quirks);
-
-#endif /* _PANTHEON_CPU_H */
diff --git a/arch/arm/include/asm/arch-pantheon/gpio.h b/arch/arm/include/asm/arch-pantheon/gpio.h
deleted file mode 100644
index e69de29..0000000
diff --git a/arch/arm/include/asm/arch-pantheon/mfp.h b/arch/arm/include/asm/arch-pantheon/mfp.h
deleted file mode 100644
index 7909d53..0000000
--- a/arch/arm/include/asm/arch-pantheon/mfp.h
+++ /dev/null
@@ -1,39 +0,0 @@
-/*
- * Based on arch/arm/include/asm/arch-armada100/mfp.h
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __PANTHEON_MFP_H
-#define __PANTHEON_MFP_H
-
-/*
- * Frequently used MFP Configuration macros for all PANTHEON family of SoCs
- *
- * offset, pull,pF, drv,dF, edge,eF ,afn,aF
- */
-/* UART2 */
-#define MFP47_UART2_RXD (MFP_REG(0x198) | MFP_AF6 | MFP_DRIVE_MEDIUM)
-#define MFP48_UART2_TXD (MFP_REG(0x19c) | MFP_AF6 | MFP_DRIVE_MEDIUM)
-#define MFP53_CI2C_SCL (MFP_REG(0x1b0) | MFP_AF2 | MFP_DRIVE_MEDIUM)
-#define MFP54_CI2C_SDA (MFP_REG(0x1b4) | MFP_AF2 | MFP_DRIVE_MEDIUM)
-
-/* More macros can be defined here... */
-#define MFP_MMC1_DAT7 (MFP_REG(0x84) | MFP_AF0 | MFP_DRIVE_MEDIUM)
-#define MFP_MMC1_DAT6 (MFP_REG(0x88) | MFP_AF0 | MFP_DRIVE_MEDIUM)
-#define MFP_MMC1_DAT5 (MFP_REG(0x8c) | MFP_AF0 | MFP_DRIVE_MEDIUM)
-#define MFP_MMC1_DAT4 (MFP_REG(0x90) | MFP_AF0 | MFP_DRIVE_MEDIUM)
-#define MFP_MMC1_DAT3 (MFP_REG(0x94) | MFP_AF0 | MFP_DRIVE_FAST)
-#define MFP_MMC1_DAT2 (MFP_REG(0x98) | MFP_AF0 | MFP_DRIVE_FAST)
-#define MFP_MMC1_DAT1 (MFP_REG(0x9c) | MFP_AF0 | MFP_DRIVE_FAST)
-#define MFP_MMC1_DAT0 (MFP_REG(0xa0) | MFP_AF0 | MFP_DRIVE_FAST)
-#define MFP_MMC1_CMD (MFP_REG(0xa4) | MFP_AF0 | MFP_DRIVE_FAST)
-#define MFP_MMC1_CLK (MFP_REG(0xa8) | MFP_AF0 | MFP_DRIVE_FAST)
-#define MFP_MMC1_CD (MFP_REG(0xac) | MFP_AF0 | MFP_DRIVE_MEDIUM)
-#define MFP_MMC1_WP (MFP_REG(0xb0) | MFP_AF0 | MFP_DRIVE_MEDIUM)
-
-#define MFP_PIN_MAX 117
-#endif
diff --git a/arch/arm/include/asm/arch-pantheon/pantheon.h b/arch/arm/include/asm/arch-pantheon/pantheon.h
deleted file mode 100644
index c3a71bf..0000000
--- a/arch/arm/include/asm/arch-pantheon/pantheon.h
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _PANTHEON_H
-#define _PANTHEON_H
-
-/* Common APB clock register bit definitions */
-#define APBC_APBCLK (1<<0) /* APB Bus Clock Enable */
-#define APBC_FNCLK (1<<1) /* Functional Clock Enable */
-#define APBC_RST (1<<2) /* Reset Generation */
-/* Functional Clock Selection Mask */
-#define APBC_FNCLKSEL(x) (((x) & 0xf) << 4)
-
-/* Common APMU register bit definitions */
-#define APMU_PERI_CLK (1<<4) /* Peripheral Clock Enable */
-#define APMU_AXI_CLK (1<<3) /* AXI Clock Enable*/
-#define APMU_PERI_RST (1<<1) /* Peripheral Reset */
-#define APMU_AXI_RST (1<<0) /* AXI Reset */
-
-/* Register Base Addresses */
-#define PANTHEON_DRAM_BASE 0xB0000000
-#define PANTHEON_TIMER_BASE 0xD4014000
-#define PANTHEON_WD_TIMER_BASE 0xD4080000
-#define PANTHEON_APBC_BASE 0xD4015000
-#define PANTHEON_UART1_BASE 0xD4017000
-#define PANTHEON_UART2_BASE 0xD4018000
-#define PANTHEON_GPIO_BASE 0xD4019000
-#define PANTHEON_MFPR_BASE 0xD401E000
-#define PANTHEON_MPMU_BASE 0xD4050000
-#define PANTHEON_APMU_BASE 0xD4282800
-#define PANTHEON_CPU_BASE 0xD4282C00
-
-#endif /* _PANTHEON_H */
diff --git a/board/Marvell/dkb/Kconfig b/board/Marvell/dkb/Kconfig
deleted file mode 100644
index f674894..0000000
--- a/board/Marvell/dkb/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_DKB
-
-config SYS_BOARD
- default "dkb"
-
-config SYS_VENDOR
- default "Marvell"
-
-config SYS_SOC
- default "pantheon"
-
-config SYS_CONFIG_NAME
- default "dkb"
-
-endif
diff --git a/board/Marvell/dkb/MAINTAINERS b/board/Marvell/dkb/MAINTAINERS
deleted file mode 100644
index c272b7a..0000000
--- a/board/Marvell/dkb/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-DKB BOARD
-M: Lei Wen <leiwen@marvell.com>
-S: Maintained
-F: board/Marvell/dkb/
-F: include/configs/dkb.h
-F: configs/dkb_defconfig
diff --git a/board/Marvell/dkb/Makefile b/board/Marvell/dkb/Makefile
deleted file mode 100644
index 9d88579..0000000
--- a/board/Marvell/dkb/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2011
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Lei Wen <leiwen@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := dkb.o
diff --git a/board/Marvell/dkb/dkb.c b/board/Marvell/dkb/dkb.c
deleted file mode 100644
index c0c3125..0000000
--- a/board/Marvell/dkb/dkb.c
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mvmfp.h>
-#include <i2c.h>
-#include <asm/arch/mfp.h>
-#include <asm/arch/cpu.h>
-#ifdef CONFIG_GENERIC_MMC
-#include <sdhci.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- u32 mfp_cfg[] = {
- /* Enable Console on UART2 */
- MFP47_UART2_RXD,
- MFP48_UART2_TXD,
-
- /* I2C */
- MFP53_CI2C_SCL,
- MFP54_CI2C_SDA,
-
- /* MMC1 */
- MFP_MMC1_DAT7,
- MFP_MMC1_DAT6,
- MFP_MMC1_DAT5,
- MFP_MMC1_DAT4,
- MFP_MMC1_DAT3,
- MFP_MMC1_DAT2,
- MFP_MMC1_DAT1,
- MFP_MMC1_DAT0,
- MFP_MMC1_CMD,
- MFP_MMC1_CLK,
- MFP_MMC1_CD,
- MFP_MMC1_WP,
-
- MFP_EOC /*End of configureation*/
- };
- /* configure MFP's */
- mfp_config(mfp_cfg);
-
- return 0;
-}
-
-int board_init(void)
-{
- /* arch number of Board */
- gd->bd->bi_arch_number = MACH_TYPE_TTC_DKB;
- /* adress of boot parameters */
- gd->bd->bi_boot_params = panth_sdram_base(0) + 0x100;
- return 0;
-}
-
-#ifdef CONFIG_GENERIC_MMC
-#define I2C_SLAVE_ADDR 0x34
-#define LDO13_REG 0x28
-#define LDO_V30 0x6
-#define LDO_VOLTAGE(x) ((x & 0x7) << 1)
-#define LDO_EN 0x1
-int board_mmc_init(bd_t *bd)
-{
- ulong mmc_base_address[CONFIG_SYS_MMC_NUM] = CONFIG_SYS_MMC_BASE;
- u8 i, data;
-
- /* set LDO 13 to 3.0v */
- data = LDO_VOLTAGE(LDO_V30) | LDO_EN;
- i2c_write(I2C_SLAVE_ADDR, LDO13_REG, 1, &data, 1);
-
- for (i = 0; i < CONFIG_SYS_MMC_NUM; i++) {
- if (mv_sdh_init(mmc_base_address[i], 0, 0,
- SDHCI_QUIRK_32BIT_DMA_ADDR))
- return 1;
- }
-
- return 0;
-}
-#endif
diff --git a/configs/dkb_defconfig b/configs/dkb_defconfig
deleted file mode 100644
index 0be9578..0000000
--- a/configs/dkb_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_DKB=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index b24bfea..ce9dcb1 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+dkb arm arm926ejs - - Lei Wen <leiwen@marvell.com>
zmx25 arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
jadecpu arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
imx31_phycore arm arm1136 - - Guennadi Liakhovetski <g.liakhovetski@gmx.de>
diff --git a/include/configs/dkb.h b/include/configs/dkb.h
deleted file mode 100644
index 7ffbb14..0000000
--- a/include/configs/dkb.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * (C) Copyright 2011
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Lei Wen <leiwen@marvell.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_DKB_H
-#define __CONFIG_DKB_H
-
-/*
- * Version number information
- */
-#define CONFIG_IDENT_STRING "\nMarvell-TTC DKB"
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SHEEVA_88SV331xV5 1 /* CPU Core subversion */
-#define CONFIG_PANTHEON 1 /* SOC Family Name */
-#define CONFIG_MACH_TTC_DKB 1 /* Machine type */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - 0x00200000)
-#define CONFIG_NR_DRAM_BANKS_MAX 2
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MMC
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-#undef CONFIG_ARCH_MISC_INIT
-
-/*
- * Environment variables configurations
- */
-#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
-#define CONFIG_ENV_SIZE 0x20000 /* 64k */
-
-#endif /* __CONFIG_DKB_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 6/9] ARM: remove cm4008 and cm41xx board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (4 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 5/9] ARM: remove dkb " Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 7/9] ARM: remove a320evb " Masahiro Yamada
` (3 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
These are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 10 -
arch/arm/cpu/arm920t/Makefile | 1 -
arch/arm/cpu/arm920t/ks8695/Makefile | 9 -
arch/arm/cpu/arm920t/ks8695/lowlevel_init.S | 189 -------------
arch/arm/cpu/arm920t/ks8695/timer.c | 77 ------
arch/arm/include/asm/arch-ks8695/platform.h | 294 ---------------------
board/cm4008/Kconfig | 12 -
board/cm4008/MAINTAINERS | 6 -
board/cm4008/Makefile | 8 -
board/cm4008/cm4008.c | 88 -------
board/cm4008/config.mk | 1 -
board/cm4008/flash.c | 395 ----------------------------
board/cm41xx/Kconfig | 12 -
board/cm41xx/MAINTAINERS | 6 -
board/cm41xx/Makefile | 8 -
board/cm41xx/cm41xx.c | 88 -------
board/cm41xx/config.mk | 1 -
board/cm41xx/flash.c | 395 ----------------------------
configs/cm4008_defconfig | 2 -
configs/cm41xx_defconfig | 2 -
doc/README.scrapyard | 2 +
drivers/net/Makefile | 1 -
drivers/net/ks8695eth.c | 229 ----------------
drivers/serial/Makefile | 1 -
drivers/serial/serial.c | 2 -
drivers/serial/serial_ks8695.c | 121 ---------
include/configs/cm4008.h | 104 --------
include/configs/cm41xx.h | 104 --------
include/netdev.h | 1 -
include/serial.h | 1 -
30 files changed, 2 insertions(+), 2168 deletions(-)
delete mode 100644 arch/arm/cpu/arm920t/ks8695/Makefile
delete mode 100644 arch/arm/cpu/arm920t/ks8695/lowlevel_init.S
delete mode 100644 arch/arm/cpu/arm920t/ks8695/timer.c
delete mode 100644 arch/arm/include/asm/arch-ks8695/platform.h
delete mode 100644 board/cm4008/Kconfig
delete mode 100644 board/cm4008/MAINTAINERS
delete mode 100644 board/cm4008/Makefile
delete mode 100644 board/cm4008/cm4008.c
delete mode 100644 board/cm4008/config.mk
delete mode 100644 board/cm4008/flash.c
delete mode 100644 board/cm41xx/Kconfig
delete mode 100644 board/cm41xx/MAINTAINERS
delete mode 100644 board/cm41xx/Makefile
delete mode 100644 board/cm41xx/cm41xx.c
delete mode 100644 board/cm41xx/config.mk
delete mode 100644 board/cm41xx/flash.c
delete mode 100644 configs/cm4008_defconfig
delete mode 100644 configs/cm41xx_defconfig
delete mode 100644 drivers/net/ks8695eth.c
delete mode 100644 drivers/serial/serial_ks8695.c
delete mode 100644 include/configs/cm4008.h
delete mode 100644 include/configs/cm41xx.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 32d89e1..e930bba 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -88,14 +88,6 @@ config TARGET_SCB9328
bool "Support scb9328"
select CPU_ARM920T
-config TARGET_CM4008
- bool "Support cm4008"
- select CPU_ARM920T
-
-config TARGET_CM41XX
- bool "Support cm41xx"
- select CPU_ARM920T
-
config TARGET_VCMA9
bool "Support VCMA9"
select CPU_ARM920T
@@ -758,8 +750,6 @@ source "board/broadcom/bcm28155_ap/Kconfig"
source "board/broadcom/bcmcygnus/Kconfig"
source "board/broadcom/bcmnsp/Kconfig"
source "board/cirrus/edb93xx/Kconfig"
-source "board/cm4008/Kconfig"
-source "board/cm41xx/Kconfig"
source "board/compulab/cm_t335/Kconfig"
source "board/compulab/cm_fx6/Kconfig"
source "board/congatec/cgtqmx6eval/Kconfig"
diff --git a/arch/arm/cpu/arm920t/Makefile b/arch/arm/cpu/arm920t/Makefile
index a16838b..29a350c 100644
--- a/arch/arm/cpu/arm920t/Makefile
+++ b/arch/arm/cpu/arm920t/Makefile
@@ -13,5 +13,4 @@ obj-$(CONFIG_USE_IRQ) += interrupts.o
obj-$(if $(filter a320,$(SOC)),y) += a320/
obj-$(CONFIG_EP93XX) += ep93xx/
obj-$(CONFIG_IMX) += imx/
-obj-$(CONFIG_KS8695) += ks8695/
obj-$(CONFIG_S3C24X0) += s3c24x0/
diff --git a/arch/arm/cpu/arm920t/ks8695/Makefile b/arch/arm/cpu/arm920t/ks8695/Makefile
deleted file mode 100644
index 400aa89..0000000
--- a/arch/arm/cpu/arm920t/ks8695/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = lowlevel_init.o
-obj-y += timer.o
diff --git a/arch/arm/cpu/arm920t/ks8695/lowlevel_init.S b/arch/arm/cpu/arm920t/ks8695/lowlevel_init.S
deleted file mode 100644
index a2a07f2..0000000
--- a/arch/arm/cpu/arm920t/ks8695/lowlevel_init.S
+++ /dev/null
@@ -1,189 +0,0 @@
-/*
- * lowlevel_init.S - basic hardware initialization for the KS8695 CPU
- *
- * Copyright (c) 2004-2005, Greg Ungerer <greg.ungerer@opengear.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/platform.h>
-
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- *************************************************************************
- *
- * Handy dandy macros
- *
- *************************************************************************
- */
-
-/* Delay a bit */
-.macro DELAY_FOR cycles, reg0
- ldr \reg0, =\cycles
- subs \reg0, \reg0, #1
- subne pc, pc, #0xc
-.endm
-
-/*
- *************************************************************************
- *
- * Some local storage.
- *
- *************************************************************************
- */
-
-/* Should we boot with an interactive console or not */
-.globl serial_console
-
-/*
- *************************************************************************
- *
- * Raw hardware initialization code. The important thing is to get
- * SDRAM setup and running. We do some other basic things here too,
- * like getting the PLL set for high speed, and init the LEDs.
- *
- *************************************************************************
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-#if DEBUG
- /*
- * enable UART for early debug trace
- */
- ldr r1, =(KS8695_IO_BASE+KS8695_UART_DIVISOR)
- mov r2, #((25000000+CONFIG_BAUDRATE/2) / CONFIG_BAUDRATE)
- str r2, [r1]
- ldr r1, =(KS8695_IO_BASE+KS8695_UART_LINE_CTRL)
- mov r2, #KS8695_UART_LINEC_WLEN8
- str r2, [r1] /* 8 data bits, no parity, 1 stop */
- ldr r1, =(KS8695_IO_BASE+KS8695_UART_TX_HOLDING)
- mov r2, #0x41
- str r2, [r1] /* write 'A' */
-#endif
-#if DEBUG
- ldr r1, =(KS8695_IO_BASE+KS8695_UART_TX_HOLDING)
- mov r2, #0x42
- str r2, [r1]
-#endif
-
- /*
- * remap the memory and flash regions. we want to end up with
- * ram from address 0, and flash at 32MB.
- */
- ldr r1, =(KS8695_IO_BASE+KS8695_MEM_CTRL0)
- ldr r2, =0xbfc00040
- str r2, [r1] /* large flash map */
- ldr pc, =(highflash+0x02000000-0x00f00000) /* jump to high flash address */
-highflash:
- ldr r2, =0x8fe00040
- str r2, [r1] /* remap flash range */
-
- /*
- * remap the second select region to the 4MB immediately after
- * the first region. This way if you have a larger flash (say 8Mb)
- * then you can have it all mapped nicely. Has no effect if you
- * only have a 4Mb or smaller flash.
- */
- ldr r1, =(KS8695_IO_BASE+KS8695_MEM_CTRL1)
- ldr r2, =0x9fe40040
- str r2, [r1] /* remap flash2 region, contiguous */
- ldr r1, =(KS8695_IO_BASE+KS8695_MEM_GENERAL)
- ldr r2, =0x30000005
- str r2, [r1] /* enable both flash selects */
-
-#ifdef CONFIG_CM41xx
- /*
- * map the second flash chip, using the external IO lines.
- */
- ldr r1, =(KS8695_IO_BASE+KS8695_IO_CTRL0)
- ldr r2, =0xafe80b6d
- str r2, [r1] /* remap io0 region, contiguous */
- ldr r1, =(KS8695_IO_BASE+KS8695_IO_CTRL1)
- ldr r2, =0xbfec0b6d
- str r2, [r1] /* remap io1 region, contiguous */
- ldr r1, =(KS8695_IO_BASE+KS8695_MEM_GENERAL)
- ldr r2, =0x30050005
- str r2, [r1] /* enable second flash */
-#endif
-
- /*
- * before relocating, we have to setup RAM timing
- */
- ldr r1, =(KS8695_IO_BASE+KS8695_SDRAM_CTRL0)
-#if (PHYS_SDRAM_1_SIZE == 0x02000000)
- ldr r2, =0x7fc0000e /* 32MB */
-#else
- ldr r2, =0x3fc0000e /* 16MB */
-#endif
- str r2, [r1] /* configure sdram bank0 setup */
- ldr r1, =(KS8695_IO_BASE+KS8695_SDRAM_CTRL1)
- mov r2, #0
- str r2, [r1] /* configure sdram bank1 setup */
-
- ldr r1, =(KS8695_IO_BASE+KS8695_SDRAM_GENERAL)
- ldr r2, =0x0000000a
- str r2, [r1] /* set RAS/CAS timing */
-
- ldr r1, =(KS8695_IO_BASE+KS8695_SDRAM_BUFFER)
- ldr r2, =0x00030000
- str r2, [r1] /* send NOP command */
- DELAY_FOR 0x100, r0
- ldr r2, =0x00010000
- str r2, [r1] /* send PRECHARGE-ALL */
- DELAY_FOR 0x100, r0
-
- ldr r1, =(KS8695_IO_BASE+KS8695_SDRAM_REFRESH)
- ldr r2, =0x00000020
- str r2, [r1] /* set for fast refresh */
- DELAY_FOR 0x100, r0
- ldr r2, =0x00000190
- str r2, [r1] /* set normal refresh timing */
-
- ldr r1, =(KS8695_IO_BASE+KS8695_SDRAM_BUFFER)
- ldr r2, =0x00020033
- str r2, [r1] /* send mode command */
- DELAY_FOR 0x100, r0
- ldr r2, =0x01f00000
- str r2, [r1] /* enable sdram fifos */
-
- /*
- * set pll to top speed
- */
- ldr r1, =(KS8695_IO_BASE+KS8695_SYSTEN_BUS_CLOCK)
- mov r2, #0
- str r2, [r1] /* set pll clock to 166MHz */
-
- ldr r1, =(KS8695_IO_BASE+KS8695_SWITCH_CTRL0)
- ldr r2, [r1] /* Get switch ctrl0 register */
- and r2, r2, #0x0fc00000 /* Mask out LED control bits */
- orr r2, r2, #0x01800000 /* Set Link/activity/speed actions */
- str r2, [r1]
-
-#ifdef CONFIG_CM4008
- ldr r1, =(KS8695_IO_BASE+KS8695_GPIO_MODE)
- ldr r2, =0x0000fe30
- str r2, [r1] /* enable LED's as outputs */
- ldr r1, =(KS8695_IO_BASE+KS8695_GPIO_DATA)
- ldr r2, =0x0000fe20
- str r2, [r1] /* turn on power LED */
-#endif
-#if defined(CONFIG_CM4008) || defined(CONFIG_CM41xx)
- ldr r2, [r1] /* get current GPIO input data */
- tst r2, #0x8 /* check if "erase" depressed */
- beq nobutton
- mov r2, #0 /* be quiet on boot, no console */
- ldr r1, =serial_console
- str r2, [r1]
-nobutton:
-#endif
-
- add lr, lr, #0x02000000 /* flash is now mapped high */
- add ip, ip, #0x02000000 /* this is a hack */
- mov pc, lr /* all done, return */
-
-#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
diff --git a/arch/arm/cpu/arm920t/ks8695/timer.c b/arch/arm/cpu/arm920t/ks8695/timer.c
deleted file mode 100644
index 23db557..0000000
--- a/arch/arm/cpu/arm920t/ks8695/timer.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * (C) Copyright 2004-2005, Greg Ungerer <greg.ungerer@opengear.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/platform.h>
-
-/*
- * Initial timer set constants. Nothing complicated, just set for a 1ms
- * tick.
- */
-#define TIMER_INTERVAL (TICKS_PER_uSEC * mSEC_1)
-#define TIMER_COUNT (TIMER_INTERVAL / 2)
-#define TIMER_PULSE TIMER_COUNT
-
-/*
- * Handy KS8695 register access functions.
- */
-#define ks8695_read(a) *((volatile ulong *) (KS8695_IO_BASE + (a)))
-#define ks8695_write(a,v) *((volatile ulong *) (KS8695_IO_BASE + (a))) = (v)
-
-ulong timer_ticks;
-
-int timer_init (void)
-{
- /* Set the hadware timer for 1ms */
- ks8695_write(KS8695_TIMER1, TIMER_COUNT);
- ks8695_write(KS8695_TIMER1_PCOUNT, TIMER_PULSE);
- ks8695_write(KS8695_TIMER_CTRL, 0x2);
- timer_ticks = 0;
-
- return 0;
-}
-
-ulong get_timer_masked(void)
-{
- /* Check for timer wrap */
- if (ks8695_read(KS8695_INT_STATUS) & KS8695_INTMASK_TIMERINT1) {
- /* Clear interrupt condition */
- ks8695_write(KS8695_INT_STATUS, KS8695_INTMASK_TIMERINT1);
- timer_ticks++;
- }
- return timer_ticks;
-}
-
-ulong get_timer(ulong base)
-{
- return (get_timer_masked() - base);
-}
-
-void __udelay(ulong usec)
-{
- ulong start = get_timer_masked();
- ulong end;
-
- /* Only 1ms resolution :-( */
- end = usec / 1000;
- while (get_timer(start) < end)
- ;
-}
-
-void reset_cpu (ulong ignored)
-{
- ulong tc;
-
- /* Set timer0 to watchdog, and let it timeout */
- tc = ks8695_read(KS8695_TIMER_CTRL) & 0x2;
- ks8695_write(KS8695_TIMER_CTRL, tc);
- ks8695_write(KS8695_TIMER0, ((10 << 8) | 0xff));
- ks8695_write(KS8695_TIMER_CTRL, (tc | 0x1));
-
- /* Should only wait here till watchdog resets */
- for (;;)
- ;
-}
diff --git a/arch/arm/include/asm/arch-ks8695/platform.h b/arch/arm/include/asm/arch-ks8695/platform.h
deleted file mode 100644
index 02f6049..0000000
--- a/arch/arm/include/asm/arch-ks8695/platform.h
+++ /dev/null
@@ -1,294 +0,0 @@
-/*
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __address_h
-#define __address_h 1
-
-#define KS8695_SDRAM_START 0x00000000
-#define KS8695_SDRAM_SIZE 0x01000000
-#define KS8695_MEM_SIZE KS8695_SDRAM_SIZE
-#define KS8695_MEM_START KS8695_SDRAM_START
-
-#define KS8695_PCMCIA_IO_BASE 0x03800000
-#define KS8695_PCMCIA_IO_SIZE 0x00040000
-
-#define KS8695_IO_BASE 0x03FF0000
-#define KS8695_IO_SIZE 0x00010000
-
-#define KS8695_SYSTEN_CONFIG 0x00
-#define KS8695_SYSTEN_BUS_CLOCK 0x04
-
-#define KS8695_FLASH_START 0x02800000
-#define KS8695_FLASH_SIZE 0x00400000
-
-/*i/o control registers offset difinitions*/
-#define KS8695_IO_CTRL0 0x4000
-#define KS8695_IO_CTRL1 0x4004
-#define KS8695_IO_CTRL2 0x4008
-#define KS8695_IO_CTRL3 0x400C
-
-/*memory control registers offset difinitions*/
-#define KS8695_MEM_CTRL0 0x4010
-#define KS8695_MEM_CTRL1 0x4014
-#define KS8695_MEM_CTRL2 0x4018
-#define KS8695_MEM_CTRL3 0x401C
-#define KS8695_MEM_GENERAL 0x4020
-#define KS8695_SDRAM_CTRL0 0x4030
-#define KS8695_SDRAM_CTRL1 0x4034
-#define KS8695_SDRAM_GENERAL 0x4038
-#define KS8695_SDRAM_BUFFER 0x403C
-#define KS8695_SDRAM_REFRESH 0x4040
-
-/*WAN control registers offset difinitions*/
-#define KS8695_WAN_DMA_TX 0x6000
-#define KS8695_WAN_DMA_RX 0x6004
-#define KS8695_WAN_DMA_TX_START 0x6008
-#define KS8695_WAN_DMA_RX_START 0x600C
-#define KS8695_WAN_TX_LIST 0x6010
-#define KS8695_WAN_RX_LIST 0x6014
-#define KS8695_WAN_MAC_LOW 0x6018
-#define KS8695_WAN_MAC_HIGH 0x601C
-#define KS8695_WAN_MAC_ELOW 0x6080
-#define KS8695_WAN_MAC_EHIGH 0x6084
-
-/*LAN control registers offset difinitions*/
-#define KS8695_LAN_DMA_TX 0x8000
-#define KS8695_LAN_DMA_RX 0x8004
-#define KS8695_LAN_DMA_TX_START 0x8008
-#define KS8695_LAN_DMA_RX_START 0x800C
-#define KS8695_LAN_TX_LIST 0x8010
-#define KS8695_LAN_RX_LIST 0x8014
-#define KS8695_LAN_MAC_LOW 0x8018
-#define KS8695_LAN_MAC_HIGH 0x801C
-#define KS8695_LAN_MAC_ELOW 0X8080
-#define KS8695_LAN_MAC_EHIGH 0X8084
-
-/*HPNA control registers offset difinitions*/
-#define KS8695_HPNA_DMA_TX 0xA000
-#define KS8695_HPNA_DMA_RX 0xA004
-#define KS8695_HPNA_DMA_TX_START 0xA008
-#define KS8695_HPNA_DMA_RX_START 0xA00C
-#define KS8695_HPNA_TX_LIST 0xA010
-#define KS8695_HPNA_RX_LIST 0xA014
-#define KS8695_HPNA_MAC_LOW 0xA018
-#define KS8695_HPNA_MAC_HIGH 0xA01C
-#define KS8695_HPNA_MAC_ELOW 0xA080
-#define KS8695_HPNA_MAC_EHIGH 0xA084
-
-/*UART control registers offset difinitions*/
-#define KS8695_UART_RX_BUFFER 0xE000
-#define KS8695_UART_TX_HOLDING 0xE004
-
-#define KS8695_UART_FIFO_CTRL 0xE008
-#define KS8695_UART_FIFO_TRIG01 0x00
-#define KS8695_UART_FIFO_TRIG04 0x80
-#define KS8695_UART_FIFO_TXRST 0x03
-#define KS8695_UART_FIFO_RXRST 0x02
-#define KS8695_UART_FIFO_FEN 0x01
-
-#define KS8695_UART_LINE_CTRL 0xE00C
-#define KS8695_UART_LINEC_BRK 0x40
-#define KS8695_UART_LINEC_EPS 0x10
-#define KS8695_UART_LINEC_PEN 0x08
-#define KS8695_UART_LINEC_STP2 0x04
-#define KS8695_UART_LINEC_WLEN8 0x03
-#define KS8695_UART_LINEC_WLEN7 0x02
-#define KS8695_UART_LINEC_WLEN6 0x01
-#define KS8695_UART_LINEC_WLEN5 0x00
-
-#define KS8695_UART_MODEM_CTRL 0xE010
-#define KS8695_UART_MODEMC_RTS 0x02
-#define KS8695_UART_MODEMC_DTR 0x01
-
-#define KS8695_UART_LINE_STATUS 0xE014
-#define KS8695_UART_LINES_TXFE 0x20
-#define KS8695_UART_LINES_BE 0x10
-#define KS8695_UART_LINES_FE 0x08
-#define KS8695_UART_LINES_PE 0x04
-#define KS8695_UART_LINES_OE 0x02
-#define KS8695_UART_LINES_RXFE 0x01
-#define KS8695_UART_LINES_ANY (KS8695_UART_LINES_OE|KS8695_UART_LINES_BE|KS8695_UART_LINES_PE|KS8695_UART_LINES_FE)
-
-#define KS8695_UART_MODEM_STATUS 0xE018
-#define KS8695_UART_MODEM_DCD 0x80
-#define KS8695_UART_MODEM_DSR 0x20
-#define KS8695_UART_MODEM_CTS 0x10
-#define KS8695_UART_MODEM_DDCD 0x08
-#define KS8695_UART_MODEM_DDSR 0x02
-#define KS8695_UART_MODEM_DCTS 0x01
-#define UART8695_MODEM_ANY 0xFF
-
-#define KS8695_UART_DIVISOR 0xE01C
-#define KS8695_UART_STATUS 0xE020
-
-/*Interrupt controlller registers offset difinitions*/
-#define KS8695_INT_CONTL 0xE200
-#define KS8695_INT_ENABLE 0xE204
-#define KS8695_INT_ENABLE_MODEM 0x0800
-#define KS8695_INT_ENABLE_ERR 0x0400
-#define KS8695_INT_ENABLE_RX 0x0200
-#define KS8695_INT_ENABLE_TX 0x0100
-
-#define KS8695_INT_STATUS 0xE208
-#define KS8695_INT_WAN_PRIORITY 0xE20C
-#define KS8695_INT_HPNA_PRIORITY 0xE210
-#define KS8695_INT_LAN_PRIORITY 0xE214
-#define KS8695_INT_TIMER_PRIORITY 0xE218
-#define KS8695_INT_UART_PRIORITY 0xE21C
-#define KS8695_INT_EXT_PRIORITY 0xE220
-#define KS8695_INT_CHAN_PRIORITY 0xE224
-#define KS8695_INT_BUSERROR_PRO 0xE228
-#define KS8695_INT_MASK_STATUS 0xE22C
-#define KS8695_FIQ_PEND_PRIORITY 0xE230
-#define KS8695_IRQ_PEND_PRIORITY 0xE234
-
-/*timer registers offset difinitions*/
-#define KS8695_TIMER_CTRL 0xE400
-#define KS8695_TIMER1 0xE404
-#define KS8695_TIMER0 0xE408
-#define KS8695_TIMER1_PCOUNT 0xE40C
-#define KS8695_TIMER0_PCOUNT 0xE410
-
-/*GPIO registers offset difinitions*/
-#define KS8695_GPIO_MODE 0xE600
-#define KS8695_GPIO_CTRL 0xE604
-#define KS8695_GPIO_DATA 0xE608
-
-/*SWITCH registers offset difinitions*/
-#define KS8695_SWITCH_CTRL0 0xE800
-#define KS8695_SWITCH_CTRL1 0xE804
-#define KS8695_SWITCH_PORT1 0xE808
-#define KS8695_SWITCH_PORT2 0xE80C
-#define KS8695_SWITCH_PORT3 0xE810
-#define KS8695_SWITCH_PORT4 0xE814
-#define KS8695_SWITCH_PORT5 0xE818
-#define KS8695_SWITCH_AUTO0 0xE81C
-#define KS8695_SWITCH_AUTO1 0xE820
-#define KS8695_SWITCH_LUE_CTRL 0xE824
-#define KS8695_SWITCH_LUE_HIGH 0xE828
-#define KS8695_SWITCH_LUE_LOW 0xE82C
-#define KS8695_SWITCH_ADVANCED 0xE830
-
-#define KS8695_SWITCH_LPPM12 0xE874
-#define KS8695_SWITCH_LPPM34 0xE878
-
-/*host communication registers difinitions*/
-#define KS8695_DSCP_HIGH 0xE834
-#define KS8695_DSCP_LOW 0xE838
-#define KS8695_SWITCH_MAC_HIGH 0xE83C
-#define KS8695_SWITCH_MAC_LOW 0xE840
-
-/*miscellaneours registers difinitions*/
-#define KS8695_MANAGE_COUNTER 0xE844
-#define KS8695_MANAGE_DATA 0xE848
-#define KS8695_LAN12_POWERMAGR 0xE84C
-#define KS8695_LAN34_POWERMAGR 0xE850
-
-#define KS8695_DEVICE_ID 0xEA00
-#define KS8695_REVISION_ID 0xEA04
-
-#define KS8695_MISC_CONTROL 0xEA08
-#define KS8695_WAN_CONTROL 0xEA0C
-#define KS8695_WAN_POWERMAGR 0xEA10
-#define KS8695_WAN_PHY_CONTROL 0xEA14
-#define KS8695_WAN_PHY_STATUS 0xEA18
-
-/* bus clock definitions*/
-#define KS8695_BUS_CLOCK_125MHZ 0x0
-#define KS8695_BUS_CLOCK_100MHZ 0x1
-#define KS8695_BUS_CLOCK_62MHZ 0x2
-#define KS8695_BUS_CLOCK_50MHZ 0x3
-#define KS8695_BUS_CLOCK_41MHZ 0x4
-#define KS8695_BUS_CLOCK_33MHZ 0x5
-#define KS8695_BUS_CLOCK_31MHZ 0x6
-#define KS8695_BUS_CLOCK_25MHZ 0x7
-
-/* -------------------------------------------------------------------------------
- * definations for IRQ
- * -------------------------------------------------------------------------------*/
-
-#define KS8695_INT_EXT_INT0 2
-#define KS8695_INT_EXT_INT1 3
-#define KS8695_INT_EXT_INT2 4
-#define KS8695_INT_EXT_INT3 5
-#define KS8695_INT_TIMERINT0 6
-#define KS8695_INT_TIMERINT1 7
-#define KS8695_INT_UART_TX 8
-#define KS8695_INT_UART_RX 9
-#define KS8695_INT_UART_LINE_ERR 10
-#define KS8695_INT_UART_MODEMS 11
-#define KS8695_INT_LAN_STOP_RX 12
-#define KS8695_INT_LAN_STOP_TX 13
-#define KS8695_INT_LAN_BUF_RX_STATUS 14
-#define KS8695_INT_LAN_BUF_TX_STATUS 15
-#define KS8695_INT_LAN_RX_STATUS 16
-#define KS8695_INT_LAN_TX_STATUS 17
-#define KS8695_INT_HPAN_STOP_RX 18
-#define KS8695_INT_HPNA_STOP_TX 19
-#define KS8695_INT_HPNA_BUF_RX_STATUS 20
-#define KS8695_INT_HPNA_BUF_TX_STATUS 21
-#define KS8695_INT_HPNA_RX_STATUS 22
-#define KS8695_INT_HPNA_TX_STATUS 23
-#define KS8695_INT_BUS_ERROR 24
-#define KS8695_INT_WAN_STOP_RX 25
-#define KS8695_INT_WAN_STOP_TX 26
-#define KS8695_INT_WAN_BUF_RX_STATUS 27
-#define KS8695_INT_WAN_BUF_TX_STATUS 28
-#define KS8695_INT_WAN_RX_STATUS 29
-#define KS8695_INT_WAN_TX_STATUS 30
-
-#define KS8695_INT_UART KS8695_INT_UART_TX
-
-/* -------------------------------------------------------------------------------
- * Interrupt bit positions
- *
- * -------------------------------------------------------------------------------
- */
-
-#define KS8695_INTMASK_EXT_INT0 ( 1 << KS8695_INT_EXT_INT0 )
-#define KS8695_INTMASK_EXT_INT1 ( 1 << KS8695_INT_EXT_INT1 )
-#define KS8695_INTMASK_EXT_INT2 ( 1 << KS8695_INT_EXT_INT2 )
-#define KS8695_INTMASK_EXT_INT3 ( 1 << KS8695_INT_EXT_INT3 )
-#define KS8695_INTMASK_TIMERINT0 ( 1 << KS8695_INT_TIMERINT0 )
-#define KS8695_INTMASK_TIMERINT1 ( 1 << KS8695_INT_TIMERINT1 )
-#define KS8695_INTMASK_UART_TX ( 1 << KS8695_INT_UART_TX )
-#define KS8695_INTMASK_UART_RX ( 1 << KS8695_INT_UART_RX )
-#define KS8695_INTMASK_UART_LINE_ERR ( 1 << KS8695_INT_UART_LINE_ERR )
-#define KS8695_INTMASK_UART_MODEMS ( 1 << KS8695_INT_UART_MODEMS )
-#define KS8695_INTMASK_LAN_STOP_RX ( 1 << KS8695_INT_LAN_STOP_RX )
-#define KS8695_INTMASK_LAN_STOP_TX ( 1 << KS8695_INT_LAN_STOP_TX )
-#define KS8695_INTMASK_LAN_BUF_RX_STATUS ( 1 << KS8695_INT_LAN_BUF_RX_STATUS )
-#define KS8695_INTMASK_LAN_BUF_TX_STATUS ( 1 << KS8695_INT_LAN_BUF_TX_STATUS )
-#define KS8695_INTMASK_LAN_RX_STATUS ( 1 << KS8695_INT_LAN_RX_STATUS )
-#define KS8695_INTMASK_LAN_TX_STATUS ( 1 << KS8695_INT_LAN_RX_STATUS )
-#define KS8695_INTMASK_HPAN_STOP_RX ( 1 << KS8695_INT_HPAN_STOP_RX )
-#define KS8695_INTMASK_HPNA_STOP_TX ( 1 << KS8695_INT_HPNA_STOP_TX )
-#define KS8695_INTMASK_HPNA_BUF_RX_STATUS ( 1 << KS8695_INT_HPNA_BUF_RX_STATUS )
-#define KS8695_INTMAKS_HPNA_BUF_TX_STATUS ( 1 << KS8695_INT_HPNA_BUF_TX_STATUS
-#define KS8695_INTMASK_HPNA_RX_STATUS ( 1 << KS8695_INT_HPNA_RX_STATUS )
-#define KS8695_INTMASK_HPNA_TX_STATUS ( 1 << KS8695_INT_HPNA_TX_STATUS )
-#define KS8695_INTMASK_BUS_ERROR ( 1 << KS8695_INT_BUS_ERROR )
-#define KS8695_INTMASK_WAN_STOP_RX ( 1 << KS8695_INT_WAN_STOP_RX )
-#define KS8695_INTMASK_WAN_STOP_TX ( 1 << KS8695_INT_WAN_STOP_TX )
-#define KS8695_INTMASK_WAN_BUF_RX_STATUS ( 1 << KS8695_INT_WAN_BUF_RX_STATUS )
-#define KS8695_INTMASK_WAN_BUF_TX_STATUS ( 1 << KS8695_INT_WAN_BUF_TX_STATUS )
-#define KS8695_INTMASK_WAN_RX_STATUS ( 1 << KS8695_INT_WAN_RX_STATUS )
-#define KS8695_INTMASK_WAN_TX_STATUS ( 1 << KS8695_INT_WAN_TX_STATUS )
-
-#define KS8695_SC_VALID_INT 0xFFFFFFFF
-#define MAXIRQNUM 31
-
-/*
- * Timer definitions
- *
- * Use timer 1 & 2
- * (both run at 25MHz).
- *
- */
-#define TICKS_PER_uSEC 25
-#define mSEC_1 1000
-#define mSEC_10 (mSEC_1 * 10)
-
-#endif
-
-/* END */
diff --git a/board/cm4008/Kconfig b/board/cm4008/Kconfig
deleted file mode 100644
index de87d5b..0000000
--- a/board/cm4008/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_CM4008
-
-config SYS_BOARD
- default "cm4008"
-
-config SYS_SOC
- default "ks8695"
-
-config SYS_CONFIG_NAME
- default "cm4008"
-
-endif
diff --git a/board/cm4008/MAINTAINERS b/board/cm4008/MAINTAINERS
deleted file mode 100644
index 5f08bc3..0000000
--- a/board/cm4008/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-CM4008 BOARD
-M: Greg Ungerer <greg.ungerer@opengear.com>
-S: Maintained
-F: board/cm4008/
-F: include/configs/cm4008.h
-F: configs/cm4008_defconfig
diff --git a/board/cm4008/Makefile b/board/cm4008/Makefile
deleted file mode 100644
index 04b1529..0000000
--- a/board/cm4008/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := cm4008.o flash.o
diff --git a/board/cm4008/cm4008.c b/board/cm4008/cm4008.c
deleted file mode 100644
index 740e164..0000000
--- a/board/cm4008/cm4008.c
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * (C) Copyright 2005
- * Greg Ungerer, OpenGear Inc, <greg.ungerer@opengear.com>
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/platform.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-
-#define ks8695_read(a) *((volatile unsigned int *) (KS8695_IO_BASE+(a)))
-#define ks8695_write(a,b) *((volatile unsigned int *) (KS8695_IO_BASE+(a))) = (b)
-
-/* ------------------------------------------------------------------------- */
-
-
-/*
- * Miscelaneous platform dependent initialisations
- */
-int env_flash_cmdline (void)
-{
- char *sp = (char *) 0x0201c020;
- char *ep;
- int len;
-
- /* Check if "erase" push button is depressed */
- if ((ks8695_read(KS8695_GPIO_DATA) & 0x8) == 0) {
- printf("### Entering network recovery mode...\n");
- setenv("bootargs", "console=ttyAM0,115200 mem=16M initrd=0x400000,6M root=/dev/ram0");
- setenv("bootcmd", "bootp 0x400000; gofsk 0x400000");
- setenv("bootdelay", "2");
- return 0;
- }
-
- /* Check for flash based kernel boot args to use as default */
- for (ep = sp, len = 0; ((len < 1024) && (*ep != 0)); ep++, len++)
- ;
-
- if ((len > 0) && (len <1024))
- setenv("bootargs", sp);
-
- return 0;
-}
-
-int board_late_init (void)
-{
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- return ks8695_eth_initialize();
-}
-
-int board_init (void)
-{
- /* arch number of CM4008 */
- gd->bd->bi_arch_number = 624;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x00000100;
-
- /* power down all but port 0 on the switch */
- ks8695_write(KS8695_SWITCH_LPPM12, 0x00000005);
- ks8695_write(KS8695_SWITCH_LPPM34, 0x00050005);
-
- return 0;
-}
-
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return (0);
-}
diff --git a/board/cm4008/config.mk b/board/cm4008/config.mk
deleted file mode 100644
index 0d5923b..0000000
--- a/board/cm4008/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x00f00000
diff --git a/board/cm4008/flash.c b/board/cm4008/flash.c
deleted file mode 100644
index 8315a57..0000000
--- a/board/cm4008/flash.c
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * (C) Copyright 2005
- * Greg Ungerer, OpenGear Inc, greg.ungerer at opengear.com
- *
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-#include <asm/sections.h>
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (unsigned char * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, unsigned char data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i;
- ulong size = 0;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- switch (i) {
- case 0:
- flash_get_size ((unsigned char *) PHYS_FLASH_1, &flash_info[i]);
- flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
- break;
- case 1:
- /* ignore for now */
- flash_info[i].flash_id = FLASH_UNKNOWN;
- break;
- default:
- panic ("configured too many flash banks!\n");
- break;
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + (__bss_end - __bss_start),
- &flash_info[0]);
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN)
- return;
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
- info->protect[i] = 0;
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F128J3A:
- printf ("28F128J3A\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (unsigned char * addr, flash_info_t * info)
-{
- volatile unsigned char value;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = 0xAA;
- addr[0x2AAA] = 0x55;
- addr[0x5555] = 0x90;
-
- mb ();
- value = addr[0];
-
- switch (value) {
-
- case (unsigned char)INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = 0xFF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- mb ();
- value = addr[2]; /* device ID */
-
- switch (value) {
-
- case (unsigned char)INTEL_ID_28F640J3A:
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case (unsigned char)INTEL_ID_28F128J3A:
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = 0xFF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int prot, sect;
- ulong type;
- int rcode = 0;
- ulong start;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot)
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- else
- printf ("\n");
-
- /* Disable interrupts which might cause a timeout here */
- disable_interrupts();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- volatile unsigned char *addr;
- unsigned char status;
-
- printf ("Erasing sector %2d ... ", sect);
-
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0);
-
- addr = (volatile unsigned char *) (info->start[sect]);
- *addr = 0x50; /* clear status register */
- *addr = 0x20; /* erase setup */
- *addr = 0xD0; /* erase confirm */
-
- while (((status = *addr) & 0x80) != 0x80) {
- if (get_timer(start) >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = 0xB0; /* suspend erase */
- *addr = 0xFF; /* reset to read mode */
- rcode = 1;
- break;
- }
- }
-
- *addr = 0x50; /* clear status register cmd */
- *addr = 0xFF; /* resest to read mode */
-
- printf (" done\n");
- }
- }
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- unsigned char data;
- int count, i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN)
- return 4;
-
- wp = addr;
- port_width = 1;
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- count = 0;
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- if (count++ > 0x800) {
- spin_wheel ();
- count = 0;
- }
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, unsigned char data)
-{
- volatile unsigned char *addr = (volatile unsigned char *) dest;
- ulong status;
- ulong start;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased@%08lx (%lx)\n", (ulong) addr,
- (ulong) * addr);
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- disable_interrupts();
-
- *addr = 0x40; /* write setup */
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0);
-
- /* wait while polling the status register */
- while (((status = *addr) & 0x80) != 0x80) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = 0xFF; /* restore read mode */
- return (1);
- }
- }
-
- *addr = 0xFF; /* restore read mode */
-
- return (0);
-}
-
-void inline spin_wheel (void)
-{
- static int p = 0;
- static char w[] = "\\/-";
-
- printf ("\010%c", w[p]);
- (++p == 3) ? (p = 0) : 0;
-}
diff --git a/board/cm41xx/Kconfig b/board/cm41xx/Kconfig
deleted file mode 100644
index 99e675b..0000000
--- a/board/cm41xx/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_CM41XX
-
-config SYS_BOARD
- default "cm41xx"
-
-config SYS_SOC
- default "ks8695"
-
-config SYS_CONFIG_NAME
- default "cm41xx"
-
-endif
diff --git a/board/cm41xx/MAINTAINERS b/board/cm41xx/MAINTAINERS
deleted file mode 100644
index f10eeb5..0000000
--- a/board/cm41xx/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-CM41XX BOARD
-#M: -
-S: Maintained
-F: board/cm41xx/
-F: include/configs/cm41xx.h
-F: configs/cm41xx_defconfig
diff --git a/board/cm41xx/Makefile b/board/cm41xx/Makefile
deleted file mode 100644
index b71ea05..0000000
--- a/board/cm41xx/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := cm41xx.o flash.o
diff --git a/board/cm41xx/cm41xx.c b/board/cm41xx/cm41xx.c
deleted file mode 100644
index eabad48..0000000
--- a/board/cm41xx/cm41xx.c
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * (C) Copyright 2005
- * Greg Ungerer, OpenGear Inc, <greg.ungerer@opengear.com>
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/platform.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-
-#define ks8695_read(a) *((volatile unsigned int *) (KS8695_IO_BASE+(a)))
-#define ks8695_write(a,b) *((volatile unsigned int *) (KS8695_IO_BASE+(a))) = (b)
-
-/* ------------------------------------------------------------------------- */
-
-
-/*
- * Miscelaneous platform dependent initialisations
- */
-int env_flash_cmdline (void)
-{
- char *sp = (char *) 0x0201c020;
- char *ep;
- int len;
-
- /* Check if "erase" push button is depressed */
- if ((ks8695_read(KS8695_GPIO_DATA) & 0x8) == 0) {
- printf("### Entering network recovery mode...\n");
- setenv("bootargs", "console=ttyAM0,115200 mem=32M initrd=0x400000,8M root=/dev/ram0");
- setenv("bootcmd", "bootp 0x400000; gofsk 0x400000");
- setenv("bootdelay", "2");
- return 0;
- }
-
- /* Check for flash based kernel boot args to use as default */
- for (ep = sp, len = 0; ((len < 1024) && (*ep != 0)); ep++, len++)
- ;
-
- if ((len > 0) && (len <1024))
- setenv("bootargs", sp);
-
- return 0;
-}
-
-int board_late_init (void)
-{
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- return ks8695_eth_initialize();
-}
-
-int board_init (void)
-{
- /* arch number of CM41xx */
- gd->bd->bi_arch_number = 672;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x00000100;
-
- /* power down all but port 0 on the switch */
- ks8695_write(KS8695_SWITCH_LPPM12, 0x00000005);
- ks8695_write(KS8695_SWITCH_LPPM34, 0x00050005);
-
- return 0;
-}
-
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return (0);
-}
diff --git a/board/cm41xx/config.mk b/board/cm41xx/config.mk
deleted file mode 100644
index 0d5923b..0000000
--- a/board/cm41xx/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x00f00000
diff --git a/board/cm41xx/flash.c b/board/cm41xx/flash.c
deleted file mode 100644
index 8315a57..0000000
--- a/board/cm41xx/flash.c
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * (C) Copyright 2005
- * Greg Ungerer, OpenGear Inc, greg.ungerer at opengear.com
- *
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-#include <asm/sections.h>
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (unsigned char * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, unsigned char data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i;
- ulong size = 0;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- switch (i) {
- case 0:
- flash_get_size ((unsigned char *) PHYS_FLASH_1, &flash_info[i]);
- flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
- break;
- case 1:
- /* ignore for now */
- flash_info[i].flash_id = FLASH_UNKNOWN;
- break;
- default:
- panic ("configured too many flash banks!\n");
- break;
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + (__bss_end - __bss_start),
- &flash_info[0]);
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN)
- return;
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
- info->protect[i] = 0;
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F128J3A:
- printf ("28F128J3A\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (unsigned char * addr, flash_info_t * info)
-{
- volatile unsigned char value;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = 0xAA;
- addr[0x2AAA] = 0x55;
- addr[0x5555] = 0x90;
-
- mb ();
- value = addr[0];
-
- switch (value) {
-
- case (unsigned char)INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = 0xFF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- mb ();
- value = addr[2]; /* device ID */
-
- switch (value) {
-
- case (unsigned char)INTEL_ID_28F640J3A:
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case (unsigned char)INTEL_ID_28F128J3A:
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = 0xFF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int prot, sect;
- ulong type;
- int rcode = 0;
- ulong start;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot)
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- else
- printf ("\n");
-
- /* Disable interrupts which might cause a timeout here */
- disable_interrupts();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- volatile unsigned char *addr;
- unsigned char status;
-
- printf ("Erasing sector %2d ... ", sect);
-
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0);
-
- addr = (volatile unsigned char *) (info->start[sect]);
- *addr = 0x50; /* clear status register */
- *addr = 0x20; /* erase setup */
- *addr = 0xD0; /* erase confirm */
-
- while (((status = *addr) & 0x80) != 0x80) {
- if (get_timer(start) >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = 0xB0; /* suspend erase */
- *addr = 0xFF; /* reset to read mode */
- rcode = 1;
- break;
- }
- }
-
- *addr = 0x50; /* clear status register cmd */
- *addr = 0xFF; /* resest to read mode */
-
- printf (" done\n");
- }
- }
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- unsigned char data;
- int count, i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN)
- return 4;
-
- wp = addr;
- port_width = 1;
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- count = 0;
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- if (count++ > 0x800) {
- spin_wheel ();
- count = 0;
- }
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, unsigned char data)
-{
- volatile unsigned char *addr = (volatile unsigned char *) dest;
- ulong status;
- ulong start;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased@%08lx (%lx)\n", (ulong) addr,
- (ulong) * addr);
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- disable_interrupts();
-
- *addr = 0x40; /* write setup */
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0);
-
- /* wait while polling the status register */
- while (((status = *addr) & 0x80) != 0x80) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = 0xFF; /* restore read mode */
- return (1);
- }
- }
-
- *addr = 0xFF; /* restore read mode */
-
- return (0);
-}
-
-void inline spin_wheel (void)
-{
- static int p = 0;
- static char w[] = "\\/-";
-
- printf ("\010%c", w[p]);
- (++p == 3) ? (p = 0) : 0;
-}
diff --git a/configs/cm4008_defconfig b/configs/cm4008_defconfig
deleted file mode 100644
index 487589d..0000000
--- a/configs/cm4008_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_CM4008=y
diff --git a/configs/cm41xx_defconfig b/configs/cm41xx_defconfig
deleted file mode 100644
index 15e9362..0000000
--- a/configs/cm41xx_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_CM41XX=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index ce9dcb1..ba84c90 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,8 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+cm4008 arm arm920t - - Greg Ungerer <greg.ungerer@opengear.com>
+cm41xx arm arm920t - -
dkb arm arm926ejs - - Lei Wen <leiwen@marvell.com>
zmx25 arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
jadecpu arm arm926ejs - - Matthias Weisser <weisserm@arcor.de>
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 46c4ac6..da5e2bc 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -33,7 +33,6 @@ obj-$(CONFIG_FTMAC110) += ftmac110.o
obj-$(CONFIG_FTMAC100) += ftmac100.o
obj-$(CONFIG_GRETH) += greth.o
obj-$(CONFIG_DRIVER_TI_KEYSTONE_NET) += keystone_net.o
-obj-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o
obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
obj-$(CONFIG_LAN91C96) += lan91c96.o
obj-$(CONFIG_MACB) += macb.o
diff --git a/drivers/net/ks8695eth.c b/drivers/net/ks8695eth.c
deleted file mode 100644
index b4822e9..0000000
--- a/drivers/net/ks8695eth.c
+++ /dev/null
@@ -1,229 +0,0 @@
-/*
- * ks8695eth.c -- KS8695 ethernet driver
- *
- * (C) Copyright 2004-2005, Greg Ungerer <greg.ungerer@opengear.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/****************************************************************************/
-
-#include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/io.h>
-#include <asm/arch/platform.h>
-
-/****************************************************************************/
-
-/*
- * Hardware register access to the KS8695 LAN ethernet port
- * (well, it is the 4 port switch really).
- */
-#define ks8695_read(a) *((volatile unsigned long *) (KS8695_IO_BASE + (a)))
-#define ks8695_write(a,v) *((volatile unsigned long *) (KS8695_IO_BASE + (a))) = (v)
-
-/****************************************************************************/
-
-/*
- * Define the descriptor in-memory data structures.
- */
-struct ks8695_txdesc {
- uint32_t owner;
- uint32_t ctrl;
- uint32_t addr;
- uint32_t next;
-};
-
-struct ks8695_rxdesc {
- uint32_t status;
- uint32_t ctrl;
- uint32_t addr;
- uint32_t next;
-};
-
-/****************************************************************************/
-
-/*
- * Allocate local data structures to use for receiving and sending
- * packets. Just to keep it all nice and simple.
- */
-
-#define TXDESCS 4
-#define RXDESCS 4
-#define BUFSIZE 2048
-
-volatile struct ks8695_txdesc ks8695_tx[TXDESCS] __attribute__((aligned(256)));
-volatile struct ks8695_rxdesc ks8695_rx[RXDESCS] __attribute__((aligned(256)));
-volatile uint8_t ks8695_bufs[BUFSIZE*(TXDESCS+RXDESCS)] __attribute__((aligned(2048)));;
-
-/****************************************************************************/
-
-/*
- * Ideally we want to use the MAC address stored in flash.
- * But we do some sanity checks in case they are not present
- * first.
- */
-unsigned char eth_mac[] = {
- 0x00, 0x13, 0xc6, 0x00, 0x00, 0x00
-};
-
-void ks8695_getmac(void)
-{
- unsigned char *fp;
- int i;
-
- /* Check if flash MAC is valid */
- fp = (unsigned char *) 0x0201c000;
- for (i = 0; (i < 6); i++) {
- if ((fp[i] != 0) && (fp[i] != 0xff))
- break;
- }
-
- /* If we found a valid looking MAC address then use it */
- if (i < 6)
- memcpy(ð_mac[0], fp, 6);
-}
-
-/****************************************************************************/
-
-static int ks8695_eth_init(struct eth_device *dev, bd_t *bd)
-{
- int i;
-
- debug ("%s(%d): eth_reset()\n", __FILE__, __LINE__);
-
- /* Reset the ethernet engines first */
- ks8695_write(KS8695_LAN_DMA_TX, 0x80000000);
- ks8695_write(KS8695_LAN_DMA_RX, 0x80000000);
-
- ks8695_getmac();
-
- /* Set MAC address */
- ks8695_write(KS8695_LAN_MAC_LOW, (eth_mac[5] | (eth_mac[4] << 8) |
- (eth_mac[3] << 16) | (eth_mac[2] << 24)));
- ks8695_write(KS8695_LAN_MAC_HIGH, (eth_mac[1] | (eth_mac[0] << 8)));
-
- /* Turn the 4 port switch on */
- i = ks8695_read(KS8695_SWITCH_CTRL0);
- ks8695_write(KS8695_SWITCH_CTRL0, (i | 0x1));
- /* ks8695_write(KS8695_WAN_CONTROL, 0x3f000066); */
-
- /* Initialize descriptor rings */
- for (i = 0; (i < TXDESCS); i++) {
- ks8695_tx[i].owner = 0;
- ks8695_tx[i].ctrl = 0;
- ks8695_tx[i].addr = (uint32_t) &ks8695_bufs[i*BUFSIZE];
- ks8695_tx[i].next = (uint32_t) &ks8695_tx[i+1];
- }
- ks8695_tx[TXDESCS-1].ctrl = 0x02000000;
- ks8695_tx[TXDESCS-1].next = (uint32_t) &ks8695_tx[0];
-
- for (i = 0; (i < RXDESCS); i++) {
- ks8695_rx[i].status = 0x80000000;
- ks8695_rx[i].ctrl = BUFSIZE - 4;
- ks8695_rx[i].addr = (uint32_t) &ks8695_bufs[(i+TXDESCS)*BUFSIZE];
- ks8695_rx[i].next = (uint32_t) &ks8695_rx[i+1];
- }
- ks8695_rx[RXDESCS-1].ctrl |= 0x00080000;
- ks8695_rx[RXDESCS-1].next = (uint32_t) &ks8695_rx[0];
-
- /* The KS8695 is pretty slow reseting the ethernets... */
- udelay(2000000);
-
- /* Enable the ethernet engine */
- ks8695_write(KS8695_LAN_TX_LIST, (uint32_t) &ks8695_tx[0]);
- ks8695_write(KS8695_LAN_RX_LIST, (uint32_t) &ks8695_rx[0]);
- ks8695_write(KS8695_LAN_DMA_TX, 0x3);
- ks8695_write(KS8695_LAN_DMA_RX, 0x71);
- ks8695_write(KS8695_LAN_DMA_RX_START, 0x1);
-
- printf("KS8695 ETHERNET: %pM\n", eth_mac);
- return 0;
-}
-
-/****************************************************************************/
-
-static void ks8695_eth_halt(struct eth_device *dev)
-{
- debug ("%s(%d): eth_halt()\n", __FILE__, __LINE__);
-
- /* Reset the ethernet engines */
- ks8695_write(KS8695_LAN_DMA_TX, 0x80000000);
- ks8695_write(KS8695_LAN_DMA_RX, 0x80000000);
-}
-
-/****************************************************************************/
-
-static int ks8695_eth_recv(struct eth_device *dev)
-{
- volatile struct ks8695_rxdesc *dp;
- int i, len = 0;
-
- debug ("%s(%d): eth_rx()\n", __FILE__, __LINE__);
-
- for (i = 0; (i < RXDESCS); i++) {
- dp= &ks8695_rx[i];
- if ((dp->status & 0x80000000) == 0) {
- len = (dp->status & 0x7ff) - 4;
- NetReceive((void *) dp->addr, len);
- dp->status = 0x80000000;
- ks8695_write(KS8695_LAN_DMA_RX_START, 0x1);
- break;
- }
- }
-
- return len;
-}
-
-/****************************************************************************/
-
-static int ks8695_eth_send(struct eth_device *dev, void *packet, int len)
-{
- volatile struct ks8695_txdesc *dp;
- static int next = 0;
-
- debug ("%s(%d): eth_send(packet=%p,len=%d)\n", __FILE__, __LINE__,
- packet, len);
-
- dp = &ks8695_tx[next];
- memcpy((void *) dp->addr, (void *) packet, len);
-
- if (len < 64) {
- memset((void *) (dp->addr + len), 0, 64-len);
- len = 64;
- }
-
- dp->ctrl = len | 0xe0000000;
- dp->owner = 0x80000000;
-
- ks8695_write(KS8695_LAN_DMA_TX, 0x3);
- ks8695_write(KS8695_LAN_DMA_TX_START, 0x1);
-
- if (++next >= TXDESCS)
- next = 0;
-
- return 0;
-}
-
-/****************************************************************************/
-
-int ks8695_eth_initialize(void)
-{
- struct eth_device *dev;
-
- dev = malloc(sizeof(*dev));
- if (dev == NULL)
- return -1;
- memset(dev, 0, sizeof(*dev));
-
- dev->iobase = KS8695_IO_BASE + KS8695_LAN_DMA_TX;
- dev->init = ks8695_eth_init;
- dev->halt = ks8695_eth_halt;
- dev->send = ks8695_eth_send;
- dev->recv = ks8695_eth_recv;
- strcpy(dev->name, "ks8695eth");
-
- eth_register(dev);
- return 0;
-}
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 63b0cbf..b385852 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -27,7 +27,6 @@ obj-$(CONFIG_OPENCORES_YANU) += opencores_yanu.o
obj-$(CONFIG_SYS_NS16550) += ns16550.o
obj-$(CONFIG_S5P) += serial_s5p.o
obj-$(CONFIG_IMX_SERIAL) += serial_imx.o
-obj-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o
obj-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
obj-$(CONFIG_MXC_UART) += serial_mxc.o
obj-$(CONFIG_PXA_SERIAL) += serial_pxa.o
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index 95c992a..9f78492 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -127,7 +127,6 @@ serial_initfunc(evb64260_serial_initialize);
serial_initfunc(imx_serial_initialize);
serial_initfunc(iop480_serial_initialize);
serial_initfunc(jz_serial_initialize);
-serial_initfunc(ks8695_serial_initialize);
serial_initfunc(leon2_serial_initialize);
serial_initfunc(leon3_serial_initialize);
serial_initfunc(lh7a40x_serial_initialize);
@@ -220,7 +219,6 @@ void serial_initialize(void)
imx_serial_initialize();
iop480_serial_initialize();
jz_serial_initialize();
- ks8695_serial_initialize();
leon2_serial_initialize();
leon3_serial_initialize();
lh7a40x_serial_initialize();
diff --git a/drivers/serial/serial_ks8695.c b/drivers/serial/serial_ks8695.c
deleted file mode 100644
index 13adabd..0000000
--- a/drivers/serial/serial_ks8695.c
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * serial.c -- KS8695 serial driver
- *
- * (C) Copyright 2004, Greg Ungerer <greg.ungerer@opengear.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/platform.h>
-#include <serial.h>
-#include <linux/compiler.h>
-
-#ifndef CONFIG_SERIAL1
-#error "Bad: you didn't configure serial ..."
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Define the UART hardware register access structure.
- */
-struct ks8695uart {
- unsigned int RX; /* 0x00 - Receive data (r) */
- unsigned int TX; /* 0x04 - Transmit data (w) */
- unsigned int FCR; /* 0x08 - Fifo Control (r/w) */
- unsigned int LCR; /* 0x0c - Line Control (r/w) */
- unsigned int MCR; /* 0x10 - Modem Control (r/w) */
- unsigned int LSR; /* 0x14 - Line Status (r/w) */
- unsigned int MSR; /* 0x18 - Modem Status (r/w) */
- unsigned int BD; /* 0x1c - Baud Rate (r/w) */
- unsigned int SR; /* 0x20 - Status (r/w) */
-};
-
-#define KS8695_UART_ADDR ((void *) (KS8695_IO_BASE + KS8695_UART_RX_BUFFER))
-#define KS8695_UART_CLK 25000000
-
-
-/*
- * Under some circumstances we want to be "quiet" and not issue any
- * serial output - though we want u-boot to otherwise work and behave
- * the same. By default be noisy.
- */
-int serial_console = 1;
-
-
-static void ks8695_serial_setbrg(void)
-{
- volatile struct ks8695uart *uartp = KS8695_UART_ADDR;
-
- /* Set to global baud rate and 8 data bits, no parity, 1 stop bit*/
- uartp->BD = KS8695_UART_CLK / gd->baudrate;
- uartp->LCR = KS8695_UART_LINEC_WLEN8;
-}
-
-static int ks8695_serial_init(void)
-{
- serial_console = 1;
- serial_setbrg();
- return 0;
-}
-
-static void ks8695_serial_raw_putc(const char c)
-{
- volatile struct ks8695uart *uartp = KS8695_UART_ADDR;
- int i;
-
- for (i = 0; (i < 0x100000); i++) {
- if (uartp->LSR & KS8695_UART_LINES_TXFE)
- break;
- }
-
- uartp->TX = c;
-}
-
-static void ks8695_serial_putc(const char c)
-{
- if (serial_console) {
- ks8695_serial_raw_putc(c);
- if (c == '\n')
- ks8695_serial_raw_putc('\r');
- }
-}
-
-static int ks8695_serial_tstc(void)
-{
- volatile struct ks8695uart *uartp = KS8695_UART_ADDR;
- if (serial_console)
- return ((uartp->LSR & KS8695_UART_LINES_RXFE) ? 1 : 0);
- return 0;
-}
-
-static int ks8695_serial_getc(void)
-{
- volatile struct ks8695uart *uartp = KS8695_UART_ADDR;
-
- while ((uartp->LSR & KS8695_UART_LINES_RXFE) == 0)
- ;
- return (uartp->RX);
-}
-
-static struct serial_device ks8695_serial_drv = {
- .name = "ks8695_serial",
- .start = ks8695_serial_init,
- .stop = NULL,
- .setbrg = ks8695_serial_setbrg,
- .putc = ks8695_serial_putc,
- .puts = default_serial_puts,
- .getc = ks8695_serial_getc,
- .tstc = ks8695_serial_tstc,
-};
-
-void ks8695_serial_initialize(void)
-{
- serial_register(&ks8695_serial_drv);
-}
-
-__weak struct serial_device *default_serial_console(void)
-{
- return &ks8695_serial_drv;
-}
diff --git a/include/configs/cm4008.h b/include/configs/cm4008.h
deleted file mode 100644
index 1cb54b3..0000000
--- a/include/configs/cm4008.h
+++ /dev/null
@@ -1,104 +0,0 @@
-/*
- * (C) Copyright 2004
- * Greg Ungerer <greg.ungerer@opengear.com>.
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_KS8695 1 /* it is a KS8695 CPU */
-#define CONFIG_CM4008 1 /* it is an OpenGear CM4008 boad */
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-#define CONFIG_DRIVER_KS8695ETH /* use KS8695 ethernet driver */
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_KS8695_SERIAL
-#define CONFIG_SERIAL1
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_SAVEENV
-
-
-#define CONFIG_BOOTDELAY 0
-#define CONFIG_BOOTARGS "mem=16M console=ttyAM0,115200"
-#define CONFIG_BOOTCOMMAND "gofsk 0x02200000"
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00800000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 16 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00008000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-
-#define CONFIG_SYS_INIT_SP_ADDR 0x00020000 /* lowest 128k of RAM */
-
-#define PHYS_FLASH_1 0x02000000 /* Flash Bank #1 */
-#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment */
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/cm41xx.h b/include/configs/cm41xx.h
deleted file mode 100644
index adebd4b..0000000
--- a/include/configs/cm41xx.h
+++ /dev/null
@@ -1,104 +0,0 @@
-/*
- * (C) Copyright 2005
- * Greg Ungerer <greg.ungerer@opengear.com>.
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_KS8695 1 /* it is a KS8695 CPU */
-#define CONFIG_CM41xx 1 /* it is an OpenGear CM41xx boad */
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-#define CONFIG_DRIVER_KS8695ETH /* use KS8695 ethernet driver */
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_KS8695_SERIAL
-#define CONFIG_SERIAL1
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_SAVEENV
-
-
-#define CONFIG_BOOTDELAY 0
-#define CONFIG_BOOTARGS "mem=32M console=ttyAM0,115200"
-#define CONFIG_BOOTCOMMAND "gofsk 0x02200000"
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00800000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 16 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00008000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-
-#define CONFIG_SYS_INIT_SP_ADDR 0x00020000 /* lowest 128k of RAM */
-
-#define PHYS_FLASH_1 0x02000000 /* Flash Bank #1 */
-#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment */
-
-#endif /* __CONFIG_H */
diff --git a/include/netdev.h b/include/netdev.h
index daffc12..90140bd 100644
--- a/include/netdev.h
+++ b/include/netdev.h
@@ -55,7 +55,6 @@ int ftmac100_initialize(bd_t *bits);
int ftmac110_initialize(bd_t *bits);
int greth_initialize(bd_t *bis);
void gt6426x_eth_initialize(bd_t *bis);
-int ks8695_eth_initialize(void);
int ks8851_mll_initialize(u8 dev_num, int base_addr);
int lan91c96_initialize(u8 dev_num, int base_addr);
int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
diff --git a/include/serial.h b/include/serial.h
index 3d2e569..de40e94 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -182,7 +182,6 @@ void evb64260_serial_initialize(void);
void imx_serial_initialize(void);
void iop480_serial_initialize(void);
void jz_serial_initialize(void);
-void ks8695_serial_initialize(void);
void leon2_serial_initialize(void);
void leon3_serial_initialize(void);
void lh7a40x_serial_initialize(void);
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 7/9] ARM: remove a320evb board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (5 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 6/9] ARM: remove cm4008 and cm41xx " Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 8/9] ARM: remove tnetv107x " Masahiro Yamada
` (2 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 5 -
arch/arm/cpu/arm920t/Makefile | 1 -
arch/arm/cpu/arm920t/a320/Makefile | 9 --
arch/arm/cpu/arm920t/a320/reset.S | 10 --
arch/arm/cpu/arm920t/a320/timer.c | 118 -------------------
arch/arm/include/asm/arch-a320/a320.h | 22 ----
board/faraday/a320evb/Kconfig | 15 ---
board/faraday/a320evb/MAINTAINERS | 6 -
board/faraday/a320evb/Makefile | 9 --
board/faraday/a320evb/a320evb.c | 59 ----------
board/faraday/a320evb/lowlevel_init.S | 106 -----------------
configs/a320evb_defconfig | 2 -
doc/README.scrapyard | 1 +
include/configs/a320evb.h | 211 ----------------------------------
14 files changed, 1 insertion(+), 573 deletions(-)
delete mode 100644 arch/arm/cpu/arm920t/a320/Makefile
delete mode 100644 arch/arm/cpu/arm920t/a320/reset.S
delete mode 100644 arch/arm/cpu/arm920t/a320/timer.c
delete mode 100644 arch/arm/include/asm/arch-a320/a320.h
delete mode 100644 board/faraday/a320evb/Kconfig
delete mode 100644 board/faraday/a320evb/MAINTAINERS
delete mode 100644 board/faraday/a320evb/Makefile
delete mode 100644 board/faraday/a320evb/a320evb.c
delete mode 100644 board/faraday/a320evb/lowlevel_init.S
delete mode 100644 configs/a320evb_defconfig
delete mode 100644 include/configs/a320evb.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e930bba..d5a9d15 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -73,10 +73,6 @@ config TARGET_INTEGRATORCP_CM920T
bool "Support integratorcp_cm920t"
select CPU_ARM920T
-config TARGET_A320EVB
- bool "Support a320evb"
- select CPU_ARM920T
-
config ARCH_AT91
bool "Atmel AT91"
@@ -759,7 +755,6 @@ source "board/denx/m28evk/Kconfig"
source "board/denx/m53evk/Kconfig"
source "board/embest/mx6boards/Kconfig"
source "board/esg/ima3-mx53/Kconfig"
-source "board/faraday/a320evb/Kconfig"
source "board/freescale/ls2085a/Kconfig"
source "board/freescale/ls1021aqds/Kconfig"
source "board/freescale/ls1021atwr/Kconfig"
diff --git a/arch/arm/cpu/arm920t/Makefile b/arch/arm/cpu/arm920t/Makefile
index 29a350c..6582938 100644
--- a/arch/arm/cpu/arm920t/Makefile
+++ b/arch/arm/cpu/arm920t/Makefile
@@ -10,7 +10,6 @@ extra-y = start.o
obj-y += cpu.o
obj-$(CONFIG_USE_IRQ) += interrupts.o
-obj-$(if $(filter a320,$(SOC)),y) += a320/
obj-$(CONFIG_EP93XX) += ep93xx/
obj-$(CONFIG_IMX) += imx/
obj-$(CONFIG_S3C24X0) += s3c24x0/
diff --git a/arch/arm/cpu/arm920t/a320/Makefile b/arch/arm/cpu/arm920t/a320/Makefile
deleted file mode 100644
index bbdab58..0000000
--- a/arch/arm/cpu/arm920t/a320/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += reset.o
-obj-y += timer.o
diff --git a/arch/arm/cpu/arm920t/a320/reset.S b/arch/arm/cpu/arm920t/a320/reset.S
deleted file mode 100644
index 81f9dc9..0000000
--- a/arch/arm/cpu/arm920t/a320/reset.S
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * (C) Copyright 2009 Faraday Technology
- * Po-Yu Chuang <ratbert@faraday-tech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-.global reset_cpu
-reset_cpu:
- b reset_cpu
diff --git a/arch/arm/cpu/arm920t/a320/timer.c b/arch/arm/cpu/arm920t/a320/timer.c
deleted file mode 100644
index 1ac5b60..0000000
--- a/arch/arm/cpu/arm920t/a320/timer.c
+++ /dev/null
@@ -1,118 +0,0 @@
-/*
- * (C) Copyright 2009 Faraday Technology
- * Po-Yu Chuang <ratbert@faraday-tech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <div64.h>
-#include <asm/io.h>
-#include <faraday/ftpmu010.h>
-#include <faraday/fttmr010.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define TIMER_CLOCK 32768
-#define TIMER_LOAD_VAL 0xffffffff
-
-static inline unsigned long long tick_to_time(unsigned long long tick)
-{
- tick *= CONFIG_SYS_HZ;
- do_div(tick, gd->arch.timer_rate_hz);
-
- return tick;
-}
-
-static inline unsigned long long usec_to_tick(unsigned long long usec)
-{
- usec *= gd->arch.timer_rate_hz;
- do_div(usec, 1000000);
-
- return usec;
-}
-
-int timer_init(void)
-{
- struct fttmr010 *tmr = (struct fttmr010 *)CONFIG_FTTMR010_BASE;
- unsigned int cr;
-
- debug("%s()\n", __func__);
-
- /* disable timers */
- writel(0, &tmr->cr);
-
- /* use 32768Hz oscillator for RTC, WDT, TIMER */
- ftpmu010_32768osc_enable();
-
- /* setup timer */
- writel(TIMER_LOAD_VAL, &tmr->timer3_load);
- writel(TIMER_LOAD_VAL, &tmr->timer3_counter);
- writel(0, &tmr->timer3_match1);
- writel(0, &tmr->timer3_match2);
-
- /* we don't want timer to issue interrupts */
- writel(FTTMR010_TM3_MATCH1 |
- FTTMR010_TM3_MATCH2 |
- FTTMR010_TM3_OVERFLOW,
- &tmr->interrupt_mask);
-
- cr = readl(&tmr->cr);
- cr |= FTTMR010_TM3_CLOCK; /* use external clock */
- cr |= FTTMR010_TM3_ENABLE;
- writel(cr, &tmr->cr);
-
- gd->arch.timer_rate_hz = TIMER_CLOCK;
- gd->arch.tbu = gd->arch.tbl = 0;
-
- return 0;
-}
-
-/*
- * Get the current 64 bit timer tick count
- */
-unsigned long long get_ticks(void)
-{
- struct fttmr010 *tmr = (struct fttmr010 *)CONFIG_FTTMR010_BASE;
- ulong now = TIMER_LOAD_VAL - readl(&tmr->timer3_counter);
-
- /* increment tbu if tbl has rolled over */
- if (now < gd->arch.tbl)
- gd->arch.tbu++;
- gd->arch.tbl = now;
- return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;
-}
-
-void __udelay(unsigned long usec)
-{
- unsigned long long start;
- ulong tmo;
-
- start = get_ticks(); /* get current timestamp */
- tmo = usec_to_tick(usec); /* convert usecs to ticks */
- while ((get_ticks() - start) < tmo)
- ; /* loop till time has passed */
-}
-
-/*
- * get_timer(base) can be used to check for timeouts or
- * to measure elasped time relative to an event:
- *
- * ulong start_time = get_timer(0) sets start_time to the current
- * time value.
- * get_timer(start_time) returns the time elapsed since then.
- *
- * The time is used in CONFIG_SYS_HZ units!
- */
-ulong get_timer(ulong base)
-{
- return tick_to_time(get_ticks()) - base;
-}
-
-/*
- * Return the number of timer ticks per second.
- */
-ulong get_tbclk(void)
-{
- return gd->arch.timer_rate_hz;
-}
diff --git a/arch/arm/include/asm/arch-a320/a320.h b/arch/arm/include/asm/arch-a320/a320.h
deleted file mode 100644
index f2db8e1..0000000
--- a/arch/arm/include/asm/arch-a320/a320.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * (C) Copyright 2009 Faraday Technology
- * Po-Yu Chuang <ratbert@faraday-tech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __A320_H
-#define __A320_H
-
-/*
- * Hardware register bases
- */
-#define CONFIG_FTSMC020_BASE 0x90200000 /* Static Memory Controller */
-#define CONFIG_DEBUG_LED 0x902ffffc /* Debug LED */
-#define CONFIG_FTSDMC020_BASE 0x90300000 /* SDRAM Controller */
-#define CONFIG_FTMAC100_BASE 0x90900000 /* Ethernet */
-#define CONFIG_FTPMU010_BASE 0x98100000 /* Power Management Unit */
-#define CONFIG_FTTMR010_BASE 0x98400000 /* Timer */
-#define CONFIG_FTRTC010_BASE 0x98600000 /* Real Time Clock*/
-
-#endif /* __A320_H */
diff --git a/board/faraday/a320evb/Kconfig b/board/faraday/a320evb/Kconfig
deleted file mode 100644
index 02c42cb..0000000
--- a/board/faraday/a320evb/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_A320EVB
-
-config SYS_BOARD
- default "a320evb"
-
-config SYS_VENDOR
- default "faraday"
-
-config SYS_SOC
- default "a320"
-
-config SYS_CONFIG_NAME
- default "a320evb"
-
-endif
diff --git a/board/faraday/a320evb/MAINTAINERS b/board/faraday/a320evb/MAINTAINERS
deleted file mode 100644
index f13b015..0000000
--- a/board/faraday/a320evb/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-A320EVB BOARD
-M: Po-Yu Chuang <ratbert@faraday-tech.com>
-S: Maintained
-F: board/faraday/a320evb/
-F: include/configs/a320evb.h
-F: configs/a320evb_defconfig
diff --git a/board/faraday/a320evb/Makefile b/board/faraday/a320evb/Makefile
deleted file mode 100644
index 518ce3f..0000000
--- a/board/faraday/a320evb/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := a320evb.o
-obj-y += lowlevel_init.o
diff --git a/board/faraday/a320evb/a320evb.c b/board/faraday/a320evb/a320evb.c
deleted file mode 100644
index c42635b..0000000
--- a/board/faraday/a320evb/a320evb.c
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * (C) Copyright 2009 Faraday Technology
- * Po-Yu Chuang <ratbert@faraday-tech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-
-#include <faraday/ftsmc020.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init(void)
-{
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- ftsmc020_init(); /* initialize Flash */
- return 0;
-}
-
-int dram_init(void)
-{
- unsigned long sdram_base = PHYS_SDRAM_1;
- unsigned long expected_size = PHYS_SDRAM_1_SIZE;
- unsigned long actual_size;
-
- actual_size = get_ram_size((void *)sdram_base, expected_size);
-
- gd->ram_size = actual_size;
-
- if (expected_size != actual_size)
- printf("Warning: Only %lu of %lu MiB SDRAM is working\n",
- actual_size >> 20, expected_size >> 20);
-
- return 0;
-}
-
-int board_eth_init(bd_t *bd)
-{
- return ftmac100_initialize(bd);
-}
-
-ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
-{
- if (banknum == 0) { /* non-CFI boot flash */
- info->portwidth = FLASH_CFI_8BIT;
- info->chipwidth = FLASH_CFI_BY8;
- info->interface = FLASH_CFI_X8;
- return 1;
- } else
- return 0;
-}
diff --git a/board/faraday/a320evb/lowlevel_init.S b/board/faraday/a320evb/lowlevel_init.S
deleted file mode 100644
index d366260..0000000
--- a/board/faraday/a320evb/lowlevel_init.S
+++ /dev/null
@@ -1,106 +0,0 @@
-/*
- * (C) Copyright 2009 Faraday Technology
- * Po-Yu Chuang <ratbert@faraday-tech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#include <asm/macro.h>
-#include <faraday/ftsdmc020.h>
-
-/*
- * parameters for the SDRAM controller
- */
-#define TP0_A (CONFIG_FTSDMC020_BASE + FTSDMC020_OFFSET_TP0)
-#define TP1_A (CONFIG_FTSDMC020_BASE + FTSDMC020_OFFSET_TP1)
-#define CR_A (CONFIG_FTSDMC020_BASE + FTSDMC020_OFFSET_CR)
-#define B0_BSR_A (CONFIG_FTSDMC020_BASE + FTSDMC020_OFFSET_BANK0_BSR)
-#define ACR_A (CONFIG_FTSDMC020_BASE + FTSDMC020_OFFSET_ACR)
-
-#define TP0_D CONFIG_SYS_FTSDMC020_TP0
-#define TP1_D CONFIG_SYS_FTSDMC020_TP1
-#define CR_D1 FTSDMC020_CR_IPREC
-#define CR_D2 FTSDMC020_CR_ISMR
-#define CR_D3 FTSDMC020_CR_IREF
-
-#define B0_BSR_D (CONFIG_SYS_FTSDMC020_BANK0_BSR | \
- FTSDMC020_BANK_BASE(PHYS_SDRAM_1))
-#define ACR_D FTSDMC020_ACR_TOC(0x18)
-
-/*
- * numeric 7 segment display
- */
-.macro led, num
- write32 CONFIG_DEBUG_LED, \num
-.endm
-
-/*
- * Waiting for SDRAM to set up
- */
-.macro wait_sdram
- ldr r0, =CONFIG_FTSDMC020_BASE
-1:
- ldr r1, [r0, #FTSDMC020_OFFSET_CR]
- cmp r1, #0
- bne 1b
-.endm
-
-.globl lowlevel_init
-lowlevel_init:
- mov r11, lr
-
- led 0x0
-
- bl init_sdmc
-
- led 0x1
-
- /* everything is fine now */
- mov lr, r11
- mov pc, lr
-
-/*
- * memory initialization
- */
-init_sdmc:
- led 0x10
-
- /* set SDRAM register */
-
- write32 TP0_A, TP0_D
- led 0x11
-
- write32 TP1_A, TP1_D
- led 0x12
-
- /* set to precharge */
- write32 CR_A, CR_D1
- led 0x13
-
- wait_sdram
- led 0x14
-
- /* set mode register */
- write32 CR_A, CR_D2
- led 0x15
-
- wait_sdram
- led 0x16
-
- /* set to refresh */
- write32 CR_A, CR_D3
- led 0x17
-
- wait_sdram
- led 0x18
-
- write32 B0_BSR_A, B0_BSR_D
- led 0x19
-
- write32 ACR_A, ACR_D
- led 0x1a
-
- mov pc, lr
diff --git a/configs/a320evb_defconfig b/configs/a320evb_defconfig
deleted file mode 100644
index 5ebf5e6..0000000
--- a/configs/a320evb_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_A320EVB=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index ba84c90..7ce7101 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+a320evb arm arm920t - - Po-Yu Chuang <ratbert@faraday-tech.com>
cm4008 arm arm920t - - Greg Ungerer <greg.ungerer@opengear.com>
cm41xx arm arm920t - -
dkb arm arm926ejs - - Lei Wen <leiwen@marvell.com>
diff --git a/include/configs/a320evb.h b/include/configs/a320evb.h
deleted file mode 100644
index 0d3cf36..0000000
--- a/include/configs/a320evb.h
+++ /dev/null
@@ -1,211 +0,0 @@
-/*
- * (C) Copyright 2009 Faraday Technology
- * Po-Yu Chuang <ratbert@faraday-tech.com>
- *
- * Configuation settings for the Faraday A320 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/a320.h>
-
-/*
- * mach-type definition
- */
-#define MACH_TYPE_FARADAY 758
-#define CONFIG_MACH_TYPE MACH_TYPE_FARADAY
-
-/*
- * Linux kernel tagged list
- */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
-/*
- * CPU and Board Configuration Options
- */
-#undef CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- * Power Management Unit
- */
-#define CONFIG_FTPMU010_POWER
-
-/*
- * Timer
- */
-
-/*
- * Real Time Clock
- */
-#define CONFIG_RTC_FTRTC010
-
-/*
- * Serial console configuration
- */
-
-/* FTUART is a high speed NS 16C550A compatible UART */
-#define CONFIG_BAUDRATE 38400
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_COM1 0x98200000
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_CLK 18432000
-
-/*
- * Ethernet
- */
-#define CONFIG_FTMAC100
-
-#define CONFIG_BOOTDELAY 3
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_PING
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "A320 # " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS 16
-
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
-
-/*
- * SDRAM controller configuration
- */
-#define CONFIG_SYS_FTSDMC020_TP0 (FTSDMC020_TP0_TRAS(2) | \
- FTSDMC020_TP0_TRP(1) | \
- FTSDMC020_TP0_TRCD(1) | \
- FTSDMC020_TP0_TRF(3) | \
- FTSDMC020_TP0_TWR(1) | \
- FTSDMC020_TP0_TCL(2))
-
-#define CONFIG_SYS_FTSDMC020_TP1 (FTSDMC020_TP1_INI_PREC(4) | \
- FTSDMC020_TP1_INI_REFT(8) | \
- FTSDMC020_TP1_REF_INTV(0x180))
-
-#define CONFIG_SYS_FTSDMC020_BANK0_BSR (FTSDMC020_BANK_ENABLE | \
- FTSDMC020_BANK_DDW_X16 | \
- FTSDMC020_BANK_DSZ_256M | \
- FTSDMC020_BANK_MBW_32 | \
- FTSDMC020_BANK_SIZE_64M)
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Load address and memory test area should agree with
- * board/faraday/a320/config.mk. Be careful not to overwrite U-boot itself.
- */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x2000000)
-
-/* memtest works on 63 MB in DRAM */
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x3F00000)
-
-#define CONFIG_SYS_TEXT_BASE 0
-
-/*
- * Static memory controller configuration
- */
-
-#define CONFIG_FTSMC020
-#include <faraday/ftsmc020.h>
-
-#define FTSMC020_BANK0_CONFIG (FTSMC020_BANK_ENABLE | \
- FTSMC020_BANK_BASE(PHYS_FLASH_1) | \
- FTSMC020_BANK_SIZE_1M | \
- FTSMC020_BANK_MBW_8)
-
-#define FTSMC020_BANK0_TIMING (FTSMC020_TPR_RBE | \
- FTSMC020_TPR_AST(3) | \
- FTSMC020_TPR_CTW(3) | \
- FTSMC020_TPR_ATI(0xf) | \
- FTSMC020_TPR_AT2(3) | \
- FTSMC020_TPR_WTC(3) | \
- FTSMC020_TPR_AHT(3) | \
- FTSMC020_TPR_TRNA(0xf))
-
-#define FTSMC020_BANK1_CONFIG (FTSMC020_BANK_ENABLE | \
- FTSMC020_BANK_BASE(PHYS_FLASH_2) | \
- FTSMC020_BANK_SIZE_32M | \
- FTSMC020_BANK_MBW_32)
-
-#define FTSMC020_BANK1_TIMING (FTSMC020_TPR_AST(3) | \
- FTSMC020_TPR_CTW(3) | \
- FTSMC020_TPR_ATI(0xf) | \
- FTSMC020_TPR_AT2(3) | \
- FTSMC020_TPR_WTC(3) | \
- FTSMC020_TPR_AHT(3) | \
- FTSMC020_TPR_TRNA(0xf))
-
-#define CONFIG_SYS_FTSMC020_CONFIGS { \
- { FTSMC020_BANK0_CONFIG, FTSMC020_BANK0_TIMING, }, \
- { FTSMC020_BANK1_CONFIG, FTSMC020_BANK1_TIMING, }, \
-}
-
-/*
- * FLASH and environment organization
- */
-
-/* use CFI framework */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-/* support JEDEC */
-#define CONFIG_FLASH_CFI_LEGACY
-#define CONFIG_SYS_FLASH_LEGACY_512Kx8
-
-#define PHYS_FLASH_1 0x00000000
-#define PHYS_FLASH_2 0x00400000
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2, }
-
-#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
-
-/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2
-
-/* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-#undef CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* environments */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x60000)
-#define CONFIG_ENV_SIZE 0x20000
-
-#endif /* __CONFIG_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 8/9] ARM: remove tnetv107x board support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (6 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 7/9] ARM: remove a320evb " Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 9/9] ARM: davinci: remove hawkboard support Masahiro Yamada
2015-02-23 11:53 ` [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Fabio Estevam
9 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chan-Taek Park <c-park@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/Kconfig | 5 -
arch/arm/cpu/arm1176/Makefile | 1 -
arch/arm/cpu/arm1176/start.S | 22 --
arch/arm/cpu/arm1176/tnetv107x/Makefile | 6 -
arch/arm/cpu/arm1176/tnetv107x/aemif.c | 78 -----
arch/arm/cpu/arm1176/tnetv107x/clock.c | 432 -------------------------
arch/arm/cpu/arm1176/tnetv107x/init.c | 22 --
arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S | 10 -
arch/arm/cpu/arm1176/tnetv107x/mux.c | 319 ------------------
arch/arm/cpu/arm1176/tnetv107x/timer.c | 93 ------
arch/arm/include/asm/arch-tnetv107x/clock.h | 53 ---
arch/arm/include/asm/arch-tnetv107x/hardware.h | 160 ---------
arch/arm/include/asm/arch-tnetv107x/mux.h | 291 -----------------
board/ti/tnetv107xevm/Kconfig | 15 -
board/ti/tnetv107xevm/MAINTAINERS | 6 -
board/ti/tnetv107xevm/Makefile | 5 -
board/ti/tnetv107xevm/config.mk | 5 -
board/ti/tnetv107xevm/sdb_board.c | 134 --------
configs/tnetv107x_evm_defconfig | 2 -
doc/README.scrapyard | 1 +
drivers/watchdog/Makefile | 1 -
drivers/watchdog/tnetv107x_wdt.c | 165 ----------
include/configs/tnetv107x_evm.h | 139 --------
23 files changed, 1 insertion(+), 1964 deletions(-)
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/Makefile
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/aemif.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/clock.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/init.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/mux.c
delete mode 100644 arch/arm/cpu/arm1176/tnetv107x/timer.c
delete mode 100644 arch/arm/include/asm/arch-tnetv107x/clock.h
delete mode 100644 arch/arm/include/asm/arch-tnetv107x/hardware.h
delete mode 100644 arch/arm/include/asm/arch-tnetv107x/mux.h
delete mode 100644 board/ti/tnetv107xevm/Kconfig
delete mode 100644 board/ti/tnetv107xevm/MAINTAINERS
delete mode 100644 board/ti/tnetv107xevm/Makefile
delete mode 100644 board/ti/tnetv107xevm/config.mk
delete mode 100644 board/ti/tnetv107xevm/sdb_board.c
delete mode 100644 configs/tnetv107x_evm_defconfig
delete mode 100644 drivers/watchdog/tnetv107x_wdt.c
delete mode 100644 include/configs/tnetv107x_evm.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index d5a9d15..b9284a3 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -282,10 +282,6 @@ config TARGET_RPI_2
bool "Support rpi_2"
select CPU_V7
-config TARGET_TNETV107X_EVM
- bool "Support tnetv107x_evm"
- select CPU_ARM1176
-
config TARGET_INTEGRATORAP_CM946ES
bool "Support integratorap_cm946es"
select CPU_ARM946ES
@@ -820,7 +816,6 @@ source "board/ti/am335x/Kconfig"
source "board/ti/am43xx/Kconfig"
source "board/ti/ti814x/Kconfig"
source "board/ti/ti816x/Kconfig"
-source "board/ti/tnetv107xevm/Kconfig"
source "board/timll/devkit3250/Kconfig"
source "board/toradex/colibri_pxa270/Kconfig"
source "board/tqc/tqma6/Kconfig"
diff --git a/arch/arm/cpu/arm1176/Makefile b/arch/arm/cpu/arm1176/Makefile
index ead2303..480e130 100644
--- a/arch/arm/cpu/arm1176/Makefile
+++ b/arch/arm/cpu/arm1176/Makefile
@@ -12,4 +12,3 @@ extra-y = start.o
obj-y = cpu.o
obj-$(CONFIG_BCM2835) += bcm2835/
-obj-$(CONFIG_TNETV107X) += tnetv107x/
diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S
index 0704bdd..ac937bf 100644
--- a/arch/arm/cpu/arm1176/start.S
+++ b/arch/arm/cpu/arm1176/start.S
@@ -96,28 +96,6 @@ mmu_disable:
mov pc, r2
mmu_disable_phys:
-#ifdef CONFIG_DISABLE_TCM
- /*
- * Disable the TCMs
- */
- mrc p15, 0, r0, c0, c0, 2 /* Return TCM details */
- cmp r0, #0
- beq skip_tcmdisable
- mov r1, #0
- mov r2, #1
- tst r0, r2
- mcrne p15, 0, r1, c9, c1, 1 /* Disable Instruction TCM if present*/
- tst r0, r2, LSL #16
- mcrne p15, 0, r1, c9, c1, 0 /* Disable Data TCM if present*/
-skip_tcmdisable:
-#endif
-#endif
-
-#ifdef CONFIG_PERIPORT_REMAP
- /* Peri port setup */
- ldr r0, =CONFIG_PERIPORT_BASE
- orr r0, r0, #CONFIG_PERIPORT_SIZE
- mcr p15,0,r0,c15,c2,4
#endif
/*
diff --git a/arch/arm/cpu/arm1176/tnetv107x/Makefile b/arch/arm/cpu/arm1176/tnetv107x/Makefile
deleted file mode 100644
index a4c1edf..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += aemif.o clock.o init.o mux.o timer.o
-obj-y += lowlevel_init.o
diff --git a/arch/arm/cpu/arm1176/tnetv107x/aemif.c b/arch/arm/cpu/arm1176/tnetv107x/aemif.c
deleted file mode 100644
index a0f5728..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/aemif.c
+++ /dev/null
@@ -1,78 +0,0 @@
-/*
- * TNETV107X: Asynchronous EMIF Configuration
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/mux.h>
-
-#define ASYNC_EMIF_BASE TNETV107X_ASYNC_EMIF_CNTRL_BASE
-#define ASYNC_EMIF_CONFIG(cs) (ASYNC_EMIF_BASE+0x10+(cs)*4)
-#define ASYNC_EMIF_ONENAND_CONTROL (ASYNC_EMIF_BASE+0x5c)
-#define ASYNC_EMIF_NAND_CONTROL (ASYNC_EMIF_BASE+0x60)
-#define ASYNC_EMIF_WAITCYCLE_CONFIG (ASYNC_EMIF_BASE+0x4)
-
-#define CONFIG_SELECT_STROBE(v) ((v) ? 1 << 31 : 0)
-#define CONFIG_EXTEND_WAIT(v) ((v) ? 1 << 30 : 0)
-#define CONFIG_WR_SETUP(v) (((v) & 0x0f) << 26)
-#define CONFIG_WR_STROBE(v) (((v) & 0x3f) << 20)
-#define CONFIG_WR_HOLD(v) (((v) & 0x07) << 17)
-#define CONFIG_RD_SETUP(v) (((v) & 0x0f) << 13)
-#define CONFIG_RD_STROBE(v) (((v) & 0x3f) << 7)
-#define CONFIG_RD_HOLD(v) (((v) & 0x07) << 4)
-#define CONFIG_TURN_AROUND(v) (((v) & 0x03) << 2)
-#define CONFIG_WIDTH(v) (((v) & 0x03) << 0)
-
-#define NUM_CS 4
-
-#define set_config_field(reg, field, val) \
- do { \
- if (val != -1) { \
- reg &= ~CONFIG_##field(0xffffffff); \
- reg |= CONFIG_##field(val); \
- } \
- } while (0)
-
-void configure_async_emif(int cs, struct async_emif_config *cfg)
-{
- unsigned long tmp;
-
- if (cfg->mode == ASYNC_EMIF_MODE_NAND) {
- tmp = __raw_readl(ASYNC_EMIF_NAND_CONTROL);
- tmp |= (1 << cs);
- __raw_writel(tmp, ASYNC_EMIF_NAND_CONTROL);
-
- } else if (cfg->mode == ASYNC_EMIF_MODE_ONENAND) {
- tmp = __raw_readl(ASYNC_EMIF_ONENAND_CONTROL);
- tmp |= (1 << cs);
- __raw_writel(tmp, ASYNC_EMIF_ONENAND_CONTROL);
- }
-
- tmp = __raw_readl(ASYNC_EMIF_CONFIG(cs));
-
- set_config_field(tmp, SELECT_STROBE, cfg->select_strobe);
- set_config_field(tmp, EXTEND_WAIT, cfg->extend_wait);
- set_config_field(tmp, WR_SETUP, cfg->wr_setup);
- set_config_field(tmp, WR_STROBE, cfg->wr_strobe);
- set_config_field(tmp, WR_HOLD, cfg->wr_hold);
- set_config_field(tmp, RD_SETUP, cfg->rd_setup);
- set_config_field(tmp, RD_STROBE, cfg->rd_strobe);
- set_config_field(tmp, RD_HOLD, cfg->rd_hold);
- set_config_field(tmp, TURN_AROUND, cfg->turn_around);
- set_config_field(tmp, WIDTH, cfg->width);
-
- __raw_writel(tmp, ASYNC_EMIF_CONFIG(cs));
-}
-
-void init_async_emif(int num_cs, struct async_emif_config *config)
-{
- int cs;
-
- clk_enable(TNETV107X_LPSC_AEMIF);
-
- for (cs = 0; cs < num_cs; cs++)
- configure_async_emif(cs, config + cs);
-}
diff --git a/arch/arm/cpu/arm1176/tnetv107x/clock.c b/arch/arm/cpu/arm1176/tnetv107x/clock.c
deleted file mode 100644
index 7ba28d3..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/clock.c
+++ /dev/null
@@ -1,432 +0,0 @@
-/*
- * TNETV107X: Clock management APIs
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm-generic/errno.h>
-#include <asm/io.h>
-#include <asm/processor.h>
-#include <asm/arch/clock.h>
-
-#define CLOCK_BASE TNETV107X_CLOCK_CONTROL_BASE
-#define PSC_BASE TNETV107X_PSC_BASE
-
-#define BIT(x) (1 << (x))
-
-#define MAX_PREDIV 64
-#define MAX_POSTDIV 8UL
-#define MAX_MULT 512
-#define MAX_DIV (MAX_PREDIV * MAX_POSTDIV)
-
-/* LPSC registers */
-#define PSC_PTCMD 0x120
-#define PSC_PTSTAT 0x128
-#define PSC_MDSTAT(n) (0x800 + (n) * 4)
-#define PSC_MDCTL(n) (0xA00 + (n) * 4)
-
-#define PSC_MDCTL_LRSTZ BIT(8)
-
-#define psc_reg_read(reg) __raw_readl((u32 *)(PSC_BASE + (reg)))
-#define psc_reg_write(reg, val) __raw_writel(val, (u32 *)(PSC_BASE + (reg)))
-
-/* SSPLL registers */
-struct sspll_regs {
- u32 modes;
- u32 postdiv;
- u32 prediv;
- u32 mult_factor;
- u32 divider_range;
- u32 bw_divider;
- u32 spr_amount;
- u32 spr_rate_div;
- u32 diag;
-};
-
-/* SSPLL base addresses */
-static struct sspll_regs *sspll_regs[] = {
- (struct sspll_regs *)(CLOCK_BASE + 0x040),
- (struct sspll_regs *)(CLOCK_BASE + 0x080),
- (struct sspll_regs *)(CLOCK_BASE + 0x0c0),
-};
-
-#define sspll_reg(pll, reg) (&(sspll_regs[pll]->reg))
-#define sspll_reg_read(pll, reg) __raw_readl(sspll_reg(pll, reg))
-#define sspll_reg_write(pll, reg, val) __raw_writel(val, sspll_reg(pll, reg))
-
-
-/* PLL Control Registers */
-struct pllctl_regs {
- u32 ctl; /* 00 */
- u32 ocsel; /* 04 */
- u32 secctl; /* 08 */
- u32 __pad0;
- u32 mult; /* 10 */
- u32 prediv; /* 14 */
- u32 div1; /* 18 */
- u32 div2; /* 1c */
- u32 div3; /* 20 */
- u32 oscdiv1; /* 24 */
- u32 postdiv; /* 28 */
- u32 bpdiv; /* 2c */
- u32 wakeup; /* 30 */
- u32 __pad1;
- u32 cmd; /* 38 */
- u32 stat; /* 3c */
- u32 alnctl; /* 40 */
- u32 dchange; /* 44 */
- u32 cken; /* 48 */
- u32 ckstat; /* 4c */
- u32 systat; /* 50 */
- u32 ckctl; /* 54 */
- u32 __pad2[2];
- u32 div4; /* 60 */
- u32 div5; /* 64 */
- u32 div6; /* 68 */
- u32 div7; /* 6c */
- u32 div8; /* 70 */
-};
-
-struct lpsc_map {
- int pll, div;
-};
-
-static struct pllctl_regs *pllctl_regs[] = {
- (struct pllctl_regs *)(CLOCK_BASE + 0x700),
- (struct pllctl_regs *)(CLOCK_BASE + 0x300),
- (struct pllctl_regs *)(CLOCK_BASE + 0x500),
-};
-
-#define pllctl_reg(pll, reg) (&(pllctl_regs[pll]->reg))
-#define pllctl_reg_read(pll, reg) __raw_readl(pllctl_reg(pll, reg))
-#define pllctl_reg_write(pll, reg, val) __raw_writel(val, pllctl_reg(pll, reg))
-
-#define pllctl_reg_rmw(pll, reg, mask, val) \
- pllctl_reg_write(pll, reg, \
- (pllctl_reg_read(pll, reg) & ~(mask)) | val)
-
-#define pllctl_reg_setbits(pll, reg, mask) \
- pllctl_reg_rmw(pll, reg, 0, mask)
-
-#define pllctl_reg_clrbits(pll, reg, mask) \
- pllctl_reg_rmw(pll, reg, mask, 0)
-
-/* PLLCTL Bits */
-#define PLLCTL_CLKMODE BIT(8)
-#define PLLCTL_PLLSELB BIT(7)
-#define PLLCTL_PLLENSRC BIT(5)
-#define PLLCTL_PLLDIS BIT(4)
-#define PLLCTL_PLLRST BIT(3)
-#define PLLCTL_PLLPWRDN BIT(1)
-#define PLLCTL_PLLEN BIT(0)
-
-#define PLLDIV_ENABLE BIT(15)
-
-static int pll_div_offset[] = {
-#define div_offset(reg) offsetof(struct pllctl_regs, reg)
- div_offset(div1), div_offset(div2), div_offset(div3),
- div_offset(div4), div_offset(div5), div_offset(div6),
- div_offset(div7), div_offset(div8),
-};
-
-static unsigned long pll_bypass_mask[] = { 1, 4, 2 };
-static unsigned long pll_div_mask[] = { 0x01ff, 0x00ff, 0x00ff };
-
-/* Mappings from PLL+DIV to subsystem clocks */
-#define sys_arm1176_clk {SYS_PLL, 0}
-#define sys_dsp_clk {SYS_PLL, 1}
-#define sys_ddr_clk {SYS_PLL, 2}
-#define sys_full_clk {SYS_PLL, 3}
-#define sys_lcd_clk {SYS_PLL, 4}
-#define sys_vlynq_ref_clk {SYS_PLL, 5}
-#define sys_tsc_clk {SYS_PLL, 6}
-#define sys_half_clk {SYS_PLL, 7}
-
-#define eth_clk_5 {ETH_PLL, 0}
-#define eth_clk_50 {ETH_PLL, 1}
-#define eth_clk_125 {ETH_PLL, 2}
-#define eth_clk_250 {ETH_PLL, 3}
-#define eth_clk_25 {ETH_PLL, 4}
-
-#define tdm_clk {TDM_PLL, 0}
-#define tdm_extra_clk {TDM_PLL, 1}
-#define tdm1_clk {TDM_PLL, 2}
-
-static const struct lpsc_map lpsc_clk_map[] = {
- [TNETV107X_LPSC_ARM] = sys_arm1176_clk,
- [TNETV107X_LPSC_GEM] = sys_dsp_clk,
- [TNETV107X_LPSC_DDR2_PHY] = sys_ddr_clk,
- [TNETV107X_LPSC_TPCC] = sys_full_clk,
- [TNETV107X_LPSC_TPTC0] = sys_full_clk,
- [TNETV107X_LPSC_TPTC1] = sys_full_clk,
- [TNETV107X_LPSC_RAM] = sys_full_clk,
- [TNETV107X_LPSC_MBX_LITE] = sys_arm1176_clk,
- [TNETV107X_LPSC_LCD] = sys_lcd_clk,
- [TNETV107X_LPSC_ETHSS] = eth_clk_125,
- [TNETV107X_LPSC_AEMIF] = sys_full_clk,
- [TNETV107X_LPSC_CHIP_CFG] = sys_half_clk,
- [TNETV107X_LPSC_TSC] = sys_tsc_clk,
- [TNETV107X_LPSC_ROM] = sys_half_clk,
- [TNETV107X_LPSC_UART2] = sys_half_clk,
- [TNETV107X_LPSC_PKTSEC] = sys_half_clk,
- [TNETV107X_LPSC_SECCTL] = sys_half_clk,
- [TNETV107X_LPSC_KEYMGR] = sys_half_clk,
- [TNETV107X_LPSC_KEYPAD] = sys_half_clk,
- [TNETV107X_LPSC_GPIO] = sys_half_clk,
- [TNETV107X_LPSC_MDIO] = sys_half_clk,
- [TNETV107X_LPSC_SDIO0] = sys_half_clk,
- [TNETV107X_LPSC_UART0] = sys_half_clk,
- [TNETV107X_LPSC_UART1] = sys_half_clk,
- [TNETV107X_LPSC_TIMER0] = sys_half_clk,
- [TNETV107X_LPSC_TIMER1] = sys_half_clk,
- [TNETV107X_LPSC_WDT_ARM] = sys_half_clk,
- [TNETV107X_LPSC_WDT_DSP] = sys_half_clk,
- [TNETV107X_LPSC_SSP] = sys_half_clk,
- [TNETV107X_LPSC_TDM0] = tdm_clk,
- [TNETV107X_LPSC_VLYNQ] = sys_vlynq_ref_clk,
- [TNETV107X_LPSC_MCDMA] = sys_half_clk,
- [TNETV107X_LPSC_USB0] = sys_half_clk,
- [TNETV107X_LPSC_TDM1] = tdm1_clk,
- [TNETV107X_LPSC_DEBUGSS] = sys_half_clk,
- [TNETV107X_LPSC_ETHSS_RGMII] = eth_clk_250,
- [TNETV107X_LPSC_SYSTEM] = sys_half_clk,
- [TNETV107X_LPSC_IMCOP] = sys_dsp_clk,
- [TNETV107X_LPSC_SPARE] = sys_half_clk,
- [TNETV107X_LPSC_SDIO1] = sys_half_clk,
- [TNETV107X_LPSC_USB1] = sys_half_clk,
- [TNETV107X_LPSC_USBSS] = sys_half_clk,
- [TNETV107X_LPSC_DDR2_EMIF1_VRST] = sys_ddr_clk,
- [TNETV107X_LPSC_DDR2_EMIF2_VCTL_RST] = sys_ddr_clk,
-};
-
-static const unsigned long pll_ext_freq[] = {
- [SYS_PLL] = CONFIG_PLL_SYS_EXT_FREQ,
- [ETH_PLL] = CONFIG_PLL_ETH_EXT_FREQ,
- [TDM_PLL] = CONFIG_PLL_TDM_EXT_FREQ,
-};
-
-static unsigned long pll_freq_get(int pll)
-{
- unsigned long mult = 1, prediv = 1, postdiv = 1;
- unsigned long ref = CONFIG_SYS_INT_OSC_FREQ;
- unsigned long ret;
- u32 bypass;
-
- bypass = __raw_readl((u32 *)(CLOCK_BASE));
- if (!(bypass & pll_bypass_mask[pll])) {
- mult = sspll_reg_read(pll, mult_factor);
- prediv = sspll_reg_read(pll, prediv) + 1;
- postdiv = sspll_reg_read(pll, postdiv) + 1;
- }
-
- if (pllctl_reg_read(pll, ctl) & PLLCTL_CLKMODE)
- ref = pll_ext_freq[pll];
-
- if (!(pllctl_reg_read(pll, ctl) & PLLCTL_PLLEN))
- return ref;
-
- ret = (unsigned long)(ref + ((unsigned long long)ref * mult) / 256);
- ret /= (prediv * postdiv);
-
- return ret;
-}
-
-static unsigned long __pll_div_freq_get(int pll, unsigned int fpll,
- int div)
-{
- int divider = 1;
- unsigned long divreg;
-
- divreg = __raw_readl((void *)pllctl_regs[pll] + pll_div_offset[div]);
-
- if (divreg & PLLDIV_ENABLE)
- divider = (divreg & pll_div_mask[pll]) + 1;
-
- return fpll / divider;
-}
-
-static unsigned long pll_div_freq_get(int pll, int div)
-{
- unsigned int fpll = pll_freq_get(pll);
-
- return __pll_div_freq_get(pll, fpll, div);
-}
-
-static void __pll_div_freq_set(int pll, unsigned int fpll, int div,
- unsigned long hz)
-{
- int divider = (fpll / hz - 1);
-
- divider &= pll_div_mask[pll];
- divider |= PLLDIV_ENABLE;
-
- __raw_writel(divider, (void *)pllctl_regs[pll] + pll_div_offset[div]);
- pllctl_reg_setbits(pll, alnctl, (1 << div));
- pllctl_reg_setbits(pll, dchange, (1 << div));
-}
-
-static unsigned long pll_div_freq_set(int pll, int div, unsigned long hz)
-{
- unsigned int fpll = pll_freq_get(pll);
-
- __pll_div_freq_set(pll, fpll, div, hz);
-
- pllctl_reg_write(pll, cmd, 1);
-
- /* Wait until new divider takes effect */
- while (pllctl_reg_read(pll, stat) & 0x01);
-
- return __pll_div_freq_get(pll, fpll, div);
-}
-
-unsigned long clk_get_rate(unsigned int clk)
-{
- return pll_div_freq_get(lpsc_clk_map[clk].pll, lpsc_clk_map[clk].div);
-}
-
-unsigned long clk_round_rate(unsigned int clk, unsigned long hz)
-{
- unsigned long fpll, divider, pll;
-
- pll = lpsc_clk_map[clk].pll;
- fpll = pll_freq_get(pll);
- divider = (fpll / hz - 1);
- divider &= pll_div_mask[pll];
-
- return fpll / (divider + 1);
-}
-
-int clk_set_rate(unsigned int clk, unsigned long _hz)
-{
- unsigned long hz;
-
- hz = clk_round_rate(clk, _hz);
- if (hz != _hz)
- return -EINVAL; /* Cannot set to target freq */
-
- pll_div_freq_set(lpsc_clk_map[clk].pll, lpsc_clk_map[clk].div, hz);
- return 0;
-}
-
-void lpsc_control(int mod, unsigned long state, int lrstz)
-{
- u32 mdctl;
-
- mdctl = psc_reg_read(PSC_MDCTL(mod));
- mdctl &= ~0x1f;
- mdctl |= state;
-
- if (lrstz == 0)
- mdctl &= ~PSC_MDCTL_LRSTZ;
- else if (lrstz == 1)
- mdctl |= PSC_MDCTL_LRSTZ;
-
- psc_reg_write(PSC_MDCTL(mod), mdctl);
-
- psc_reg_write(PSC_PTCMD, 1);
-
- /* wait for power domain transition to end */
- while (psc_reg_read(PSC_PTSTAT) & 1);
-
- /* Wait for module state change */
- while ((psc_reg_read(PSC_MDSTAT(mod)) & 0x1f) != state);
-}
-
-int lpsc_status(unsigned int id)
-{
- return psc_reg_read(PSC_MDSTAT(id)) & 0x1f;
-}
-
-static void init_pll(const struct pll_init_data *data)
-{
- unsigned long fpll;
- unsigned long best_pre = 0, best_post = 0, best_mult = 0;
- unsigned long div, prediv, postdiv, mult;
- unsigned long delta, actual;
- long best_delta = -1;
- int i;
- u32 tmp;
-
- if (data->pll == SYS_PLL)
- return; /* cannot reconfigure system pll on the fly */
-
- tmp = pllctl_reg_read(data->pll, ctl);
- if (data->internal_osc) {
- tmp &= ~PLLCTL_CLKMODE;
- fpll = CONFIG_SYS_INT_OSC_FREQ;
- } else {
- tmp |= PLLCTL_CLKMODE;
- fpll = pll_ext_freq[data->pll];
- }
- pllctl_reg_write(data->pll, ctl, tmp);
-
- mult = data->pll_freq / fpll;
- for (mult = max(mult, 1UL); mult <= MAX_MULT; mult++) {
- div = (fpll * mult) / data->pll_freq;
- if (div < 1 || div > MAX_DIV)
- continue;
-
- for (postdiv = 1; postdiv <= min(div, MAX_POSTDIV); postdiv++) {
- prediv = div / postdiv;
- if (prediv < 1 || prediv > MAX_PREDIV)
- continue;
-
- actual = (fpll / prediv) * (mult / postdiv);
- delta = (actual - data->pll_freq);
- if (delta < 0)
- delta = -delta;
- if ((delta < best_delta) || (best_delta == -1)) {
- best_delta = delta;
- best_mult = mult;
- best_pre = prediv;
- best_post = postdiv;
- if (delta == 0)
- goto done;
- }
- }
- }
-done:
-
- if (best_delta == -1) {
- printf("pll cannot derive %lu from %lu\n",
- data->pll_freq, fpll);
- return;
- }
-
- fpll = fpll * best_mult;
- fpll /= best_pre * best_post;
-
- pllctl_reg_clrbits(data->pll, ctl, PLLCTL_PLLENSRC);
- pllctl_reg_clrbits(data->pll, ctl, PLLCTL_PLLEN);
-
- pllctl_reg_setbits(data->pll, ctl, PLLCTL_PLLRST);
-
- pllctl_reg_clrbits(data->pll, ctl, PLLCTL_PLLPWRDN);
- pllctl_reg_clrbits(data->pll, ctl, PLLCTL_PLLDIS);
-
- sspll_reg_write(data->pll, mult_factor, (best_mult - 1) << 8);
- sspll_reg_write(data->pll, prediv, best_pre - 1);
- sspll_reg_write(data->pll, postdiv, best_post - 1);
-
- for (i = 0; i < 10; i++)
- if (data->div_freq[i])
- __pll_div_freq_set(data->pll, fpll, i,
- data->div_freq[i]);
-
- pllctl_reg_write(data->pll, cmd, 1);
-
- /* Wait until pll "go" operation completes */
- while (pllctl_reg_read(data->pll, stat) & 0x01);
-
- pllctl_reg_clrbits(data->pll, ctl, PLLCTL_PLLRST);
- pllctl_reg_setbits(data->pll, ctl, PLLCTL_PLLEN);
-}
-
-void init_plls(int num_pll, struct pll_init_data *config)
-{
- int i;
-
- for (i = 0; i < num_pll; i++)
- init_pll(&config[i]);
-}
diff --git a/arch/arm/cpu/arm1176/tnetv107x/init.c b/arch/arm/cpu/arm1176/tnetv107x/init.c
deleted file mode 100644
index d870826..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/init.c
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * TNETV107X: Architecture initialization
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-void chip_configuration_unlock(void)
-{
- __raw_writel(TNETV107X_KICK0_MAGIC, TNETV107X_KICK0);
- __raw_writel(TNETV107X_KICK1_MAGIC, TNETV107X_KICK1);
-}
-
-int arch_cpu_init(void)
-{
- icache_enable();
- chip_configuration_unlock();
-
- return 0;
-}
diff --git a/arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S b/arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S
deleted file mode 100644
index a8bce47..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/lowlevel_init.S
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * TNETV107X: Low-level pre-relocation initialization
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-.globl lowlevel_init
-lowlevel_init:
- /* nothing for now, maybe needed for more exotic boot modes */
- mov pc, lr
diff --git a/arch/arm/cpu/arm1176/tnetv107x/mux.c b/arch/arm/cpu/arm1176/tnetv107x/mux.c
deleted file mode 100644
index 310d84d..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/mux.c
+++ /dev/null
@@ -1,319 +0,0 @@
-/*
- * TNETV107X: Pinmux configuration
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/mux.h>
-
-#define MUX_MODE_1 0x00
-#define MUX_MODE_2 0x04
-#define MUX_MODE_3 0x0c
-#define MUX_MODE_4 0x1c
-
-#define MUX_DEBUG 0
-
-static const struct pin_config pin_table[] = {
- /* reg shift mode */
- TNETV107X_MUX_CFG(0, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(0, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(0, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(0, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(0, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(0, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(0, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(0, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(0, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(0, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(0, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(0, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(1, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(1, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(1, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(1, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(1, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(1, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(1, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(1, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(1, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(1, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(1, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(1, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(2, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(2, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(2, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(2, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(2, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(2, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(2, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(2, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(2, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(2, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(2, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(2, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(3, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 0, MUX_MODE_4),
- TNETV107X_MUX_CFG(3, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(3, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 5, MUX_MODE_4),
- TNETV107X_MUX_CFG(3, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(3, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 10, MUX_MODE_4),
- TNETV107X_MUX_CFG(3, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(3, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 15, MUX_MODE_4),
- TNETV107X_MUX_CFG(3, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(3, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 20, MUX_MODE_4),
- TNETV107X_MUX_CFG(3, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(3, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(3, 25, MUX_MODE_4),
- TNETV107X_MUX_CFG(4, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(4, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(4, 0, MUX_MODE_4),
- TNETV107X_MUX_CFG(4, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(4, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(4, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(4, 15, MUX_MODE_4),
- TNETV107X_MUX_CFG(4, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(4, 20, MUX_MODE_3),
- TNETV107X_MUX_CFG(4, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(4, 25, MUX_MODE_4),
- TNETV107X_MUX_CFG(5, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(5, 0, MUX_MODE_4),
- TNETV107X_MUX_CFG(5, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(5, 5, MUX_MODE_4),
- TNETV107X_MUX_CFG(5, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(5, 10, MUX_MODE_4),
- TNETV107X_MUX_CFG(5, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(5, 15, MUX_MODE_4),
- TNETV107X_MUX_CFG(5, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(5, 20, MUX_MODE_4),
- TNETV107X_MUX_CFG(5, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(5, 25, MUX_MODE_4),
- TNETV107X_MUX_CFG(6, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(6, 0, MUX_MODE_4),
- TNETV107X_MUX_CFG(6, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(6, 5, MUX_MODE_4),
- TNETV107X_MUX_CFG(6, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(6, 10, MUX_MODE_4),
- TNETV107X_MUX_CFG(6, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(6, 15, MUX_MODE_4),
- TNETV107X_MUX_CFG(6, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(6, 20, MUX_MODE_4),
- TNETV107X_MUX_CFG(6, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(6, 25, MUX_MODE_4),
- TNETV107X_MUX_CFG(7, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(7, 0, MUX_MODE_4),
- TNETV107X_MUX_CFG(7, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(7, 5, MUX_MODE_4),
- TNETV107X_MUX_CFG(7, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(7, 10, MUX_MODE_4),
- TNETV107X_MUX_CFG(7, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(7, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(7, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(7, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(7, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(7, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(8, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(8, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(8, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(8, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(8, 5, MUX_MODE_4),
- TNETV107X_MUX_CFG(8, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(8, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(9, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(9, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(9, 0, MUX_MODE_4),
- TNETV107X_MUX_CFG(9, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(9, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(9, 5, MUX_MODE_4),
- TNETV107X_MUX_CFG(9, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(9, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(9, 10, MUX_MODE_4),
- TNETV107X_MUX_CFG(9, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(9, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(9, 15, MUX_MODE_4),
- TNETV107X_MUX_CFG(9, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(9, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(9, 20, MUX_MODE_4),
- TNETV107X_MUX_CFG(10, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(10, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(10, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(10, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(10, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(10, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(10, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(10, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(10, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(10, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(10, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(10, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(11, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(11, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(12, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(12, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(12, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(12, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(12, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(12, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(13, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(13, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(13, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(13, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(14, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(14, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(14, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(14, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(14, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(14, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(15, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(15, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(15, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(15, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(15, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(15, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(15, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(15, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(16, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(16, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(16, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(16, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(16, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(16, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(16, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(17, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(17, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(17, 0, MUX_MODE_3),
- TNETV107X_MUX_CFG(17, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(17, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(17, 5, MUX_MODE_3),
- TNETV107X_MUX_CFG(17, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(17, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(17, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(17, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(17, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(17, 15, MUX_MODE_3),
- TNETV107X_MUX_CFG(18, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(18, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(18, 0, MUX_MODE_3),
- TNETV107X_MUX_CFG(18, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(18, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(18, 5, MUX_MODE_3),
- TNETV107X_MUX_CFG(18, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(18, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(18, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(18, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(18, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(18, 15, MUX_MODE_3),
- TNETV107X_MUX_CFG(19, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(19, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(19, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(19, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(19, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(19, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(20, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(20, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(20, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(20, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(20, 15, MUX_MODE_3),
- TNETV107X_MUX_CFG(20, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(20, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(21, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(21, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(21, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(21, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(21, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(21, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 5, MUX_MODE_3),
- TNETV107X_MUX_CFG(22, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(22, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(22, 15, MUX_MODE_3),
- TNETV107X_MUX_CFG(22, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 20, MUX_MODE_3),
- TNETV107X_MUX_CFG(22, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(22, 25, MUX_MODE_3),
- TNETV107X_MUX_CFG(23, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(23, 0, MUX_MODE_3),
- TNETV107X_MUX_CFG(23, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(23, 5, MUX_MODE_3),
- TNETV107X_MUX_CFG(23, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(23, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(24, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(24, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(24, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(24, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(24, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(24, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(24, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(24, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(24, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(24, 15, MUX_MODE_3),
- TNETV107X_MUX_CFG(24, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(24, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(24, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(24, 25, MUX_MODE_2),
- TNETV107X_MUX_CFG(25, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(25, 0, MUX_MODE_2),
- TNETV107X_MUX_CFG(25, 0, MUX_MODE_3),
- TNETV107X_MUX_CFG(25, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(25, 5, MUX_MODE_2),
- TNETV107X_MUX_CFG(25, 5, MUX_MODE_3),
- TNETV107X_MUX_CFG(25, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(25, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(25, 10, MUX_MODE_3),
- TNETV107X_MUX_CFG(25, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(25, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(25, 15, MUX_MODE_3),
- TNETV107X_MUX_CFG(25, 15, MUX_MODE_4),
- TNETV107X_MUX_CFG(26, 0, MUX_MODE_1),
- TNETV107X_MUX_CFG(26, 5, MUX_MODE_1),
- TNETV107X_MUX_CFG(26, 10, MUX_MODE_1),
- TNETV107X_MUX_CFG(26, 10, MUX_MODE_2),
- TNETV107X_MUX_CFG(26, 15, MUX_MODE_1),
- TNETV107X_MUX_CFG(26, 15, MUX_MODE_2),
- TNETV107X_MUX_CFG(26, 20, MUX_MODE_1),
- TNETV107X_MUX_CFG(26, 20, MUX_MODE_2),
- TNETV107X_MUX_CFG(26, 25, MUX_MODE_1),
- TNETV107X_MUX_CFG(26, 25, MUX_MODE_2),
-};
-
-const int pin_table_size = sizeof(pin_table) / sizeof(pin_table[0]);
-
-int mux_select_pin(short index)
-{
- const struct pin_config *cfg;
- unsigned long mask, mode, reg;
-
- if (index >= pin_table_size)
- return 0;
-
- cfg = &pin_table[index];
-
- mask = 0x1f << cfg->mask_offset;
- mode = cfg->mode << cfg->mask_offset;
-
- reg = __raw_readl(TNETV107X_PINMUX(cfg->reg_index));
- reg = (reg & ~mask) | mode;
- __raw_writel(reg, TNETV107X_PINMUX(cfg->reg_index));
-
- return 1;
-}
-
-int mux_select_pins(const short *pins)
-{
- int i, ret = 1;
-
- for (i = 0; pins[i] >= 0; i++)
- ret &= mux_select_pin(pins[i]);
-
- return ret;
-}
diff --git a/arch/arm/cpu/arm1176/tnetv107x/timer.c b/arch/arm/cpu/arm1176/tnetv107x/timer.c
deleted file mode 100644
index 6e0dd0d..0000000
--- a/arch/arm/cpu/arm1176/tnetv107x/timer.c
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * TNETV107X: Timer implementation
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-
-struct timer_regs {
- u_int32_t pid12;
- u_int32_t pad[3];
- u_int32_t tim12;
- u_int32_t tim34;
- u_int32_t prd12;
- u_int32_t prd34;
- u_int32_t tcr;
- u_int32_t tgcr;
- u_int32_t wdtcr;
-};
-
-#define regs ((struct timer_regs *)CONFIG_SYS_TIMERBASE)
-
-#define TIMER_LOAD_VAL (CONFIG_SYS_HZ_CLOCK / CONFIG_SYS_HZ)
-#define TIM_CLK_DIV 16
-
-static ulong timestamp;
-static ulong lastinc;
-
-int timer_init(void)
-{
- clk_enable(TNETV107X_LPSC_TIMER0);
-
- lastinc = timestamp = 0;
-
- /* We are using timer34 in unchained 32-bit mode, full speed */
- __raw_writel(0x0, ®s->tcr);
- __raw_writel(0x0, ®s->tgcr);
- __raw_writel(0x06 | ((TIM_CLK_DIV - 1) << 8), ®s->tgcr);
- __raw_writel(0x0, ®s->tim34);
- __raw_writel(TIMER_LOAD_VAL, ®s->prd34);
- __raw_writel(2 << 22, ®s->tcr);
-
- return 0;
-}
-
-static ulong get_timer_raw(void)
-{
- ulong now = __raw_readl(®s->tim34);
-
- if (now >= lastinc)
- timestamp += now - lastinc;
- else
- timestamp += now + TIMER_LOAD_VAL - lastinc;
-
- lastinc = now;
-
- return timestamp;
-}
-
-ulong get_timer(ulong base)
-{
- return (get_timer_raw() / (TIMER_LOAD_VAL / TIM_CLK_DIV)) - base;
-}
-
-unsigned long long get_ticks(void)
-{
- return get_timer(0);
-}
-
-void __udelay(unsigned long usec)
-{
- ulong tmo;
- ulong endtime;
- signed long diff;
-
- tmo = CONFIG_SYS_HZ_CLOCK / 1000;
- tmo *= usec;
- tmo /= (1000 * TIM_CLK_DIV);
-
- endtime = get_timer_raw() + tmo;
-
- do {
- ulong now = get_timer_raw();
- diff = endtime - now;
- } while (diff >= 0);
-}
-
-ulong get_tbclk(void)
-{
- return CONFIG_SYS_HZ;
-}
diff --git a/arch/arm/include/asm/arch-tnetv107x/clock.h b/arch/arm/include/asm/arch-tnetv107x/clock.h
deleted file mode 100644
index dfc3b1b..0000000
--- a/arch/arm/include/asm/arch-tnetv107x/clock.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * TNETV107X: Clock APIs
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __ASM_ARCH_CLOCK_H
-#define __ASM_ARCH_CLOCK_H
-
-#define PSC_MDCTL_NEXT_SWRSTDISABLE 0x0
-#define PSC_MDCTL_NEXT_SYNCRST 0x1
-#define PSC_MDCTL_NEXT_DISABLE 0x2
-#define PSC_MDCTL_NEXT_ENABLE 0x3
-
-#define CONFIG_SYS_INT_OSC_FREQ 24000000
-
-#ifndef __ASSEMBLY__
-
-/* PLL identifiers */
-enum pll_type_e {
- SYS_PLL,
- TDM_PLL,
- ETH_PLL
-};
-
-/* PLL configuration data */
-struct pll_init_data {
- int pll;
- int internal_osc;
- unsigned long pll_freq;
- unsigned long div_freq[10];
-};
-
-void init_plls(int num_pll, struct pll_init_data *config);
-int lpsc_status(unsigned int mod);
-void lpsc_control(int mod, unsigned long state, int lrstz);
-unsigned long clk_get_rate(unsigned int clk);
-unsigned long clk_round_rate(unsigned int clk, unsigned long hz);
-int clk_set_rate(unsigned int clk, unsigned long hz);
-
-static inline void clk_enable(unsigned int mod)
-{
- lpsc_control(mod, PSC_MDCTL_NEXT_ENABLE, -1);
-}
-
-static inline void clk_disable(unsigned int mod)
-{
- lpsc_control(mod, PSC_MDCTL_NEXT_DISABLE, -1);
-}
-
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-tnetv107x/hardware.h b/arch/arm/include/asm/arch-tnetv107x/hardware.h
deleted file mode 100644
index d458e0b..0000000
--- a/arch/arm/include/asm/arch-tnetv107x/hardware.h
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * TNETV107X: Hardware information
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#ifndef __ASSEMBLY__
-
-#include <linux/sizes.h>
-
-#define ASYNC_EMIF_NUM_CS 4
-#define ASYNC_EMIF_MODE_NOR 0
-#define ASYNC_EMIF_MODE_NAND 1
-#define ASYNC_EMIF_MODE_ONENAND 2
-#define ASYNC_EMIF_PRESERVE -1
-
-struct async_emif_config {
- unsigned mode;
- unsigned select_strobe;
- unsigned extend_wait;
- unsigned wr_setup;
- unsigned wr_strobe;
- unsigned wr_hold;
- unsigned rd_setup;
- unsigned rd_strobe;
- unsigned rd_hold;
- unsigned turn_around;
- enum {
- ASYNC_EMIF_8 = 0,
- ASYNC_EMIF_16 = 1,
- ASYNC_EMIF_32 = 2,
- } width;
-};
-
-void init_async_emif(int num_cs, struct async_emif_config *config);
-
-int wdt_start(unsigned long msecs);
-int wdt_stop(void);
-int wdt_kick(void);
-
-#endif
-
-/* Chip configuration unlock codes and registers */
-#define TNETV107X_KICK0 (TNETV107X_CHIP_CONFIG_SYS_BASE+0x38)
-#define TNETV107X_KICK1 (TNETV107X_CHIP_CONFIG_SYS_BASE+0x3c)
-#define TNETV107X_PINMUX(n) (TNETV107X_CHIP_CONFIG_SYS_BASE+0x150+(n)*4)
-#define TNETV107X_KICK0_MAGIC 0x83e70b13
-#define TNETV107X_KICK1_MAGIC 0x95a4f1e0
-
-/* Module base addresses */
-#define TNETV107X_TPCC_BASE 0x01C00000
-#define TNETV107X_TPTC0_BASE 0x01C10000
-#define TNETV107X_TPTC1_BASE 0x01C10400
-#define TNETV107X_INTC_BASE 0x03000000
-#define TNETV107X_LCD_CONTROLLER_BASE 0x08030000
-#define TNETV107X_INTD_BASE 0x08038000
-#define TNETV107X_INTD_IPC_BASE 0x08038000
-#define TNETV107X_INTD_FAST_BASE 0x08039000
-#define TNETV107X_INTD_ASYNC_BASE 0x0803A000
-#define TNETV107X_INTD_SLOW_BASE 0x0803B000
-#define TNETV107X_PKA_BASE 0x08040000
-#define TNETV107X_RNG_BASE 0x08044000
-#define TNETV107X_TIMER0_BASE 0x08086500
-#define TNETV107X_TIMER1_BASE 0x08086600
-#define TNETV107X_WDT0_ARM_BASE 0x08086700
-#define TNETV107X_WDT1_DSP_BASE 0x08086800
-#define TNETV107X_CHIP_CONFIG_SYS_BASE 0x08087000
-#define TNETV107X_GPIO_BASE 0x08088000
-#define TNETV107X_UART1_BASE 0x08088400
-#define TNETV107X_TOUCHSCREEN_BASE 0x08088500
-#define TNETV107X_SDIO0_BASE 0x08088700
-#define TNETV107X_SDIO1_BASE 0x08088800
-#define TNETV107X_MDIO_BASE 0x08088900
-#define TNETV107X_KEYPAD_BASE 0x08088A00
-#define TNETV107X_SSP_BASE 0x08088C00
-#define TNETV107X_CLOCK_CONTROL_BASE 0x0808A000
-#define TNETV107X_PSC_BASE 0x0808B000
-#define TNETV107X_TDM0_BASE 0x08100000
-#define TNETV107X_TDM1_BASE 0x08100100
-#define TNETV107X_MCDMA_BASE 0x08108000
-#define TNETV107X_UART0_DMA_BASE 0x08108200
-#define TNETV107X_USBSS_BASE 0x08120000
-#define TNETV107X_VLYNQ_CONTROL_BASE 0x0810D000
-#define TNETV107X_ASYNC_EMIF_CNTRL_BASE 0x08200000
-#define TNETV107X_VLYNQ_MEM_MAP_BASE 0x0C000000
-#define TNETV107X_IMCOP_BASE 0x01CC0000
-#define TNETV107X_MBX_LITE_BASE 0x07000000
-#define TNETV107X_ETHSS_BASE 0x0803C000
-#define TNETV107X_CPSW_BASE 0x0803C000
-#define TNETV107X_SPF_BASE 0x0803C800
-#define TNETV107X_IOPU_ETHSS_BASE 0x0803D000
-#define TNETV107X_VTP_CNTRL_0 0x0803D800
-#define TNETV107X_VTP_CNTRL_1 0x0803D900
-#define TNETV107X_UART2_DMA_BASE 0x08108400
-#define TNETV107X_INTERNAL_MEMORY 0x20000000
-#define TNETV107X_ASYNC_EMIF_DATA_CE0_BASE 0x30000000
-#define TNETV107X_ASYNC_EMIF_DATA_CE1_BASE 0x40000000
-#define TNETV107X_ASYNC_EMIF_DATA_CE2_BASE 0x44000000
-#define TNETV107X_ASYNC_EMIF_DATA_CE3_BASE 0x48000000
-#define TNETV107X_DDR_EMIF_DATA_BASE 0x80000000
-#define TNETV107X_DDR_EMIF_CONTROL_BASE 0x90000000
-
-/* LPSC module definitions */
-#define TNETV107X_LPSC_ARM 0
-#define TNETV107X_LPSC_GEM 1
-#define TNETV107X_LPSC_DDR2_PHY 2
-#define TNETV107X_LPSC_TPCC 3
-#define TNETV107X_LPSC_TPTC0 4
-#define TNETV107X_LPSC_TPTC1 5
-#define TNETV107X_LPSC_RAM 6
-#define TNETV107X_LPSC_MBX_LITE 7
-#define TNETV107X_LPSC_LCD 8
-#define TNETV107X_LPSC_ETHSS 9
-#define TNETV107X_LPSC_AEMIF 10
-#define TNETV107X_LPSC_CHIP_CFG 11
-#define TNETV107X_LPSC_TSC 12
-#define TNETV107X_LPSC_ROM 13
-#define TNETV107X_LPSC_UART2 14
-#define TNETV107X_LPSC_PKTSEC 15
-#define TNETV107X_LPSC_SECCTL 16
-#define TNETV107X_LPSC_KEYMGR 17
-#define TNETV107X_LPSC_KEYPAD 18
-#define TNETV107X_LPSC_GPIO 19
-#define TNETV107X_LPSC_MDIO 20
-#define TNETV107X_LPSC_SDIO0 21
-#define TNETV107X_LPSC_UART0 22
-#define TNETV107X_LPSC_UART1 23
-#define TNETV107X_LPSC_TIMER0 24
-#define TNETV107X_LPSC_TIMER1 25
-#define TNETV107X_LPSC_WDT_ARM 26
-#define TNETV107X_LPSC_WDT_DSP 27
-#define TNETV107X_LPSC_SSP 28
-#define TNETV107X_LPSC_TDM0 29
-#define TNETV107X_LPSC_VLYNQ 30
-#define TNETV107X_LPSC_MCDMA 31
-#define TNETV107X_LPSC_USB0 32
-#define TNETV107X_LPSC_TDM1 33
-#define TNETV107X_LPSC_DEBUGSS 34
-#define TNETV107X_LPSC_ETHSS_RGMII 35
-#define TNETV107X_LPSC_SYSTEM 36
-#define TNETV107X_LPSC_IMCOP 37
-#define TNETV107X_LPSC_SPARE 38
-#define TNETV107X_LPSC_SDIO1 39
-#define TNETV107X_LPSC_USB1 40
-#define TNETV107X_LPSC_USBSS 41
-#define TNETV107X_LPSC_DDR2_EMIF1_VRST 42
-#define TNETV107X_LPSC_DDR2_EMIF2_VCTL_RST 43
-#define TNETV107X_LPSC_MAX 44
-
-/* Interrupt controller */
-#define INTC_GLB_EN (TNETV107X_INTC_BASE + 0x10)
-#define INTC_HINT_EN (TNETV107X_INTC_BASE + 0x1500)
-#define INTC_EN_CLR0 (TNETV107X_INTC_BASE + 0x380)
-
-#define DAVINCI_ASYNC_EMIF_CNTRL_BASE TNETV107X_ASYNC_EMIF_CNTRL_BASE
-
-#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/include/asm/arch-tnetv107x/mux.h b/arch/arm/include/asm/arch-tnetv107x/mux.h
deleted file mode 100644
index 3f832c4..0000000
--- a/arch/arm/include/asm/arch-tnetv107x/mux.h
+++ /dev/null
@@ -1,291 +0,0 @@
-/*
- * TNETV107X: Pinmux APIs
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __ASM_ARCH_MUX_H
-#define __ASM_ARCH_MUX_H
-
-struct pin_config {
- unsigned char reg_index;
- unsigned char mask_offset;
- unsigned char mode;
-};
-
-#define TNETV107X_MUX_CFG(reg, offset, mux_mode) \
- { reg, offset, mux_mode }
-
-int mux_select_pin(short index);
-int mux_select_pins(const short *pins);
-
-enum tnetv107x_pin_mux_index {
- TNETV107X_PIN_ASR_A00,
- TNETV107X_PIN_GPIO32,
- TNETV107X_PIN_ASR_A01,
- TNETV107X_PIN_GPIO33,
- TNETV107X_PIN_ASR_A02,
- TNETV107X_PIN_GPIO34,
- TNETV107X_PIN_ASR_A03,
- TNETV107X_PIN_GPIO35,
- TNETV107X_PIN_ASR_A04,
- TNETV107X_PIN_GPIO36,
- TNETV107X_PIN_ASR_A05,
- TNETV107X_PIN_GPIO37,
- TNETV107X_PIN_ASR_A06,
- TNETV107X_PIN_GPIO38,
- TNETV107X_PIN_ASR_A07,
- TNETV107X_PIN_GPIO39,
- TNETV107X_PIN_ASR_A08,
- TNETV107X_PIN_GPIO40,
- TNETV107X_PIN_ASR_A09,
- TNETV107X_PIN_GPIO41,
- TNETV107X_PIN_ASR_A10,
- TNETV107X_PIN_GPIO42,
- TNETV107X_PIN_ASR_A11,
- TNETV107X_PIN_BOOT_STRP_0,
- TNETV107X_PIN_ASR_A12,
- TNETV107X_PIN_BOOT_STRP_1,
- TNETV107X_PIN_ASR_A13,
- TNETV107X_PIN_GPIO43,
- TNETV107X_PIN_ASR_A14,
- TNETV107X_PIN_GPIO44,
- TNETV107X_PIN_ASR_A15,
- TNETV107X_PIN_GPIO45,
- TNETV107X_PIN_ASR_A16,
- TNETV107X_PIN_GPIO46,
- TNETV107X_PIN_ASR_A17,
- TNETV107X_PIN_GPIO47,
- TNETV107X_PIN_ASR_A18,
- TNETV107X_PIN_GPIO48,
- TNETV107X_PIN_SDIO1_DATA3_0,
- TNETV107X_PIN_ASR_A19,
- TNETV107X_PIN_GPIO49,
- TNETV107X_PIN_SDIO1_DATA2_0,
- TNETV107X_PIN_ASR_A20,
- TNETV107X_PIN_GPIO50,
- TNETV107X_PIN_SDIO1_DATA1_0,
- TNETV107X_PIN_ASR_A21,
- TNETV107X_PIN_GPIO51,
- TNETV107X_PIN_SDIO1_DATA0_0,
- TNETV107X_PIN_ASR_A22,
- TNETV107X_PIN_GPIO52,
- TNETV107X_PIN_SDIO1_CMD_0,
- TNETV107X_PIN_ASR_A23,
- TNETV107X_PIN_GPIO53,
- TNETV107X_PIN_SDIO1_CLK_0,
- TNETV107X_PIN_ASR_BA_1,
- TNETV107X_PIN_GPIO54,
- TNETV107X_PIN_SYS_PLL_CLK,
- TNETV107X_PIN_ASR_CS0,
- TNETV107X_PIN_ASR_CS1,
- TNETV107X_PIN_ASR_CS2,
- TNETV107X_PIN_TDM_PLL_CLK,
- TNETV107X_PIN_ASR_CS3,
- TNETV107X_PIN_ETH_PHY_CLK,
- TNETV107X_PIN_ASR_D00,
- TNETV107X_PIN_GPIO55,
- TNETV107X_PIN_ASR_D01,
- TNETV107X_PIN_GPIO56,
- TNETV107X_PIN_ASR_D02,
- TNETV107X_PIN_GPIO57,
- TNETV107X_PIN_ASR_D03,
- TNETV107X_PIN_GPIO58,
- TNETV107X_PIN_ASR_D04,
- TNETV107X_PIN_GPIO59_0,
- TNETV107X_PIN_ASR_D05,
- TNETV107X_PIN_GPIO60_0,
- TNETV107X_PIN_ASR_D06,
- TNETV107X_PIN_GPIO61_0,
- TNETV107X_PIN_ASR_D07,
- TNETV107X_PIN_GPIO62_0,
- TNETV107X_PIN_ASR_D08,
- TNETV107X_PIN_GPIO63_0,
- TNETV107X_PIN_ASR_D09,
- TNETV107X_PIN_GPIO64_0,
- TNETV107X_PIN_ASR_D10,
- TNETV107X_PIN_SDIO1_DATA3_1,
- TNETV107X_PIN_ASR_D11,
- TNETV107X_PIN_SDIO1_DATA2_1,
- TNETV107X_PIN_ASR_D12,
- TNETV107X_PIN_SDIO1_DATA1_1,
- TNETV107X_PIN_ASR_D13,
- TNETV107X_PIN_SDIO1_DATA0_1,
- TNETV107X_PIN_ASR_D14,
- TNETV107X_PIN_SDIO1_CMD_1,
- TNETV107X_PIN_ASR_D15,
- TNETV107X_PIN_SDIO1_CLK_1,
- TNETV107X_PIN_ASR_OE,
- TNETV107X_PIN_BOOT_STRP_2,
- TNETV107X_PIN_ASR_RNW,
- TNETV107X_PIN_GPIO29_0,
- TNETV107X_PIN_ASR_WAIT,
- TNETV107X_PIN_GPIO30_0,
- TNETV107X_PIN_ASR_WE,
- TNETV107X_PIN_BOOT_STRP_3,
- TNETV107X_PIN_ASR_WE_DQM0,
- TNETV107X_PIN_GPIO31,
- TNETV107X_PIN_LCD_PD17_0,
- TNETV107X_PIN_ASR_WE_DQM1,
- TNETV107X_PIN_ASR_BA0_0,
- TNETV107X_PIN_VLYNQ_CLK,
- TNETV107X_PIN_GPIO14,
- TNETV107X_PIN_LCD_PD19_0,
- TNETV107X_PIN_VLYNQ_RXD0,
- TNETV107X_PIN_GPIO15,
- TNETV107X_PIN_LCD_PD20_0,
- TNETV107X_PIN_VLYNQ_RXD1,
- TNETV107X_PIN_GPIO16,
- TNETV107X_PIN_LCD_PD21_0,
- TNETV107X_PIN_VLYNQ_TXD0,
- TNETV107X_PIN_GPIO17,
- TNETV107X_PIN_LCD_PD22_0,
- TNETV107X_PIN_VLYNQ_TXD1,
- TNETV107X_PIN_GPIO18,
- TNETV107X_PIN_LCD_PD23_0,
- TNETV107X_PIN_SDIO0_CLK,
- TNETV107X_PIN_GPIO19,
- TNETV107X_PIN_SDIO0_CMD,
- TNETV107X_PIN_GPIO20,
- TNETV107X_PIN_SDIO0_DATA0,
- TNETV107X_PIN_GPIO21,
- TNETV107X_PIN_SDIO0_DATA1,
- TNETV107X_PIN_GPIO22,
- TNETV107X_PIN_SDIO0_DATA2,
- TNETV107X_PIN_GPIO23,
- TNETV107X_PIN_SDIO0_DATA3,
- TNETV107X_PIN_GPIO24,
- TNETV107X_PIN_EMU0,
- TNETV107X_PIN_EMU1,
- TNETV107X_PIN_RTCK,
- TNETV107X_PIN_TRST_N,
- TNETV107X_PIN_TCK,
- TNETV107X_PIN_TDI,
- TNETV107X_PIN_TDO,
- TNETV107X_PIN_TMS,
- TNETV107X_PIN_TDM1_CLK,
- TNETV107X_PIN_TDM1_RX,
- TNETV107X_PIN_TDM1_TX,
- TNETV107X_PIN_TDM1_FS,
- TNETV107X_PIN_KEYPAD_R0,
- TNETV107X_PIN_KEYPAD_R1,
- TNETV107X_PIN_KEYPAD_R2,
- TNETV107X_PIN_KEYPAD_R3,
- TNETV107X_PIN_KEYPAD_R4,
- TNETV107X_PIN_KEYPAD_R5,
- TNETV107X_PIN_KEYPAD_R6,
- TNETV107X_PIN_GPIO12,
- TNETV107X_PIN_KEYPAD_R7,
- TNETV107X_PIN_GPIO10,
- TNETV107X_PIN_KEYPAD_C0,
- TNETV107X_PIN_KEYPAD_C1,
- TNETV107X_PIN_KEYPAD_C2,
- TNETV107X_PIN_KEYPAD_C3,
- TNETV107X_PIN_KEYPAD_C4,
- TNETV107X_PIN_KEYPAD_C5,
- TNETV107X_PIN_KEYPAD_C6,
- TNETV107X_PIN_GPIO13,
- TNETV107X_PIN_TEST_CLK_IN,
- TNETV107X_PIN_KEYPAD_C7,
- TNETV107X_PIN_GPIO11,
- TNETV107X_PIN_SSP0_0,
- TNETV107X_PIN_SCC_DCLK,
- TNETV107X_PIN_LCD_PD20_1,
- TNETV107X_PIN_SSP0_1,
- TNETV107X_PIN_SCC_CS_N,
- TNETV107X_PIN_LCD_PD21_1,
- TNETV107X_PIN_SSP0_2,
- TNETV107X_PIN_SCC_D,
- TNETV107X_PIN_LCD_PD22_1,
- TNETV107X_PIN_SSP0_3,
- TNETV107X_PIN_SCC_RESETN,
- TNETV107X_PIN_LCD_PD23_1,
- TNETV107X_PIN_SSP1_0,
- TNETV107X_PIN_GPIO25,
- TNETV107X_PIN_UART2_CTS,
- TNETV107X_PIN_SSP1_1,
- TNETV107X_PIN_GPIO26,
- TNETV107X_PIN_UART2_RD,
- TNETV107X_PIN_SSP1_2,
- TNETV107X_PIN_GPIO27,
- TNETV107X_PIN_UART2_RTS,
- TNETV107X_PIN_SSP1_3,
- TNETV107X_PIN_GPIO28,
- TNETV107X_PIN_UART2_TD,
- TNETV107X_PIN_UART0_CTS,
- TNETV107X_PIN_UART0_RD,
- TNETV107X_PIN_UART0_RTS,
- TNETV107X_PIN_UART0_TD,
- TNETV107X_PIN_UART1_RD,
- TNETV107X_PIN_UART1_TD,
- TNETV107X_PIN_LCD_AC_NCS,
- TNETV107X_PIN_LCD_HSYNC_RNW,
- TNETV107X_PIN_LCD_VSYNC_A0,
- TNETV107X_PIN_LCD_MCLK,
- TNETV107X_PIN_LCD_PD16_0,
- TNETV107X_PIN_LCD_PCLK_E,
- TNETV107X_PIN_LCD_PD00,
- TNETV107X_PIN_LCD_PD01,
- TNETV107X_PIN_LCD_PD02,
- TNETV107X_PIN_LCD_PD03,
- TNETV107X_PIN_LCD_PD04,
- TNETV107X_PIN_LCD_PD05,
- TNETV107X_PIN_LCD_PD06,
- TNETV107X_PIN_LCD_PD07,
- TNETV107X_PIN_LCD_PD08,
- TNETV107X_PIN_GPIO59_1,
- TNETV107X_PIN_LCD_PD09,
- TNETV107X_PIN_GPIO60_1,
- TNETV107X_PIN_LCD_PD10,
- TNETV107X_PIN_ASR_BA0_1,
- TNETV107X_PIN_GPIO61_1,
- TNETV107X_PIN_LCD_PD11,
- TNETV107X_PIN_GPIO62_1,
- TNETV107X_PIN_LCD_PD12,
- TNETV107X_PIN_GPIO63_1,
- TNETV107X_PIN_LCD_PD13,
- TNETV107X_PIN_GPIO64_1,
- TNETV107X_PIN_LCD_PD14,
- TNETV107X_PIN_GPIO29_1,
- TNETV107X_PIN_LCD_PD15,
- TNETV107X_PIN_GPIO30_1,
- TNETV107X_PIN_EINT0,
- TNETV107X_PIN_GPIO08,
- TNETV107X_PIN_EINT1,
- TNETV107X_PIN_GPIO09,
- TNETV107X_PIN_GPIO00,
- TNETV107X_PIN_LCD_PD20_2,
- TNETV107X_PIN_TDM_CLK_IN_2,
- TNETV107X_PIN_GPIO01,
- TNETV107X_PIN_LCD_PD21_2,
- TNETV107X_PIN_24M_CLK_OUT_1,
- TNETV107X_PIN_GPIO02,
- TNETV107X_PIN_LCD_PD22_2,
- TNETV107X_PIN_GPIO03,
- TNETV107X_PIN_LCD_PD23_2,
- TNETV107X_PIN_GPIO04,
- TNETV107X_PIN_LCD_PD16_1,
- TNETV107X_PIN_USB0_RXERR,
- TNETV107X_PIN_GPIO05,
- TNETV107X_PIN_LCD_PD17_1,
- TNETV107X_PIN_TDM_CLK_IN_1,
- TNETV107X_PIN_GPIO06,
- TNETV107X_PIN_LCD_PD18,
- TNETV107X_PIN_24M_CLK_OUT_2,
- TNETV107X_PIN_GPIO07,
- TNETV107X_PIN_LCD_PD19_1,
- TNETV107X_PIN_USB1_RXERR,
- TNETV107X_PIN_ETH_PLL_CLK,
- TNETV107X_PIN_MDIO,
- TNETV107X_PIN_MDC,
- TNETV107X_PIN_AIC_MUTE_STAT_N,
- TNETV107X_PIN_TDM0_CLK,
- TNETV107X_PIN_AIC_HNS_EN_N,
- TNETV107X_PIN_TDM0_FS,
- TNETV107X_PIN_AIC_HDS_EN_STAT_N,
- TNETV107X_PIN_TDM0_TX,
- TNETV107X_PIN_AIC_HNF_EN_STAT_N,
- TNETV107X_PIN_TDM0_RX,
-};
-
-#endif
diff --git a/board/ti/tnetv107xevm/Kconfig b/board/ti/tnetv107xevm/Kconfig
deleted file mode 100644
index 637f20e..0000000
--- a/board/ti/tnetv107xevm/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_TNETV107X_EVM
-
-config SYS_BOARD
- default "tnetv107xevm"
-
-config SYS_VENDOR
- default "ti"
-
-config SYS_SOC
- default "tnetv107x"
-
-config SYS_CONFIG_NAME
- default "tnetv107x_evm"
-
-endif
diff --git a/board/ti/tnetv107xevm/MAINTAINERS b/board/ti/tnetv107xevm/MAINTAINERS
deleted file mode 100644
index 8a92c6b..0000000
--- a/board/ti/tnetv107xevm/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-TNETV107XEVM BOARD
-#M: Chan-Taek Park <c-park@ti.com>
-S: Orphan (since 2014-06)
-F: board/ti/tnetv107xevm/
-F: include/configs/tnetv107x_evm.h
-F: configs/tnetv107x_evm_defconfig
diff --git a/board/ti/tnetv107xevm/Makefile b/board/ti/tnetv107xevm/Makefile
deleted file mode 100644
index 0a6128f..0000000
--- a/board/ti/tnetv107xevm/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += sdb_board.o
diff --git a/board/ti/tnetv107xevm/config.mk b/board/ti/tnetv107xevm/config.mk
deleted file mode 100644
index 51c2886..0000000
--- a/board/ti/tnetv107xevm/config.mk
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-CONFIG_SYS_TEXT_BASE = 0x83FC0000
diff --git a/board/ti/tnetv107xevm/sdb_board.c b/board/ti/tnetv107xevm/sdb_board.c
deleted file mode 100644
index a84ec84..0000000
--- a/board/ti/tnetv107xevm/sdb_board.c
+++ /dev/null
@@ -1,134 +0,0 @@
-/*
- * TNETV107X-EVM: Board initialization
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <linux/mtd/nand.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/clock.h>
-#include <asm/io.h>
-#include <asm/mach-types.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/mux.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static struct async_emif_config async_emif_config[ASYNC_EMIF_NUM_CS] = {
- { /* CS0 */
- .mode = ASYNC_EMIF_MODE_NAND,
- .wr_setup = 5,
- .wr_strobe = 5,
- .wr_hold = 2,
- .rd_setup = 5,
- .rd_strobe = 5,
- .rd_hold = 2,
- .turn_around = 5,
- .width = ASYNC_EMIF_8,
- },
- { /* CS1 */
- .mode = ASYNC_EMIF_MODE_NOR,
- .wr_setup = 2,
- .wr_strobe = 27,
- .wr_hold = 4,
- .rd_setup = 2,
- .rd_strobe = 27,
- .rd_hold = 4,
- .turn_around = 2,
- .width = ASYNC_EMIF_PRESERVE,
- },
- { /* CS2 */
- .mode = ASYNC_EMIF_MODE_NOR,
- .wr_setup = 2,
- .wr_strobe = 27,
- .wr_hold = 4,
- .rd_setup = 2,
- .rd_strobe = 27,
- .rd_hold = 4,
- .turn_around = 2,
- .width = ASYNC_EMIF_PRESERVE,
- },
- { /* CS3 */
- .mode = ASYNC_EMIF_MODE_NOR,
- .wr_setup = 1,
- .wr_strobe = 90,
- .wr_hold = 3,
- .rd_setup = 1,
- .rd_strobe = 26,
- .rd_hold = 3,
- .turn_around = 1,
- .width = ASYNC_EMIF_8,
- },
-};
-
-static struct pll_init_data pll_config[] = {
- {
- .pll = ETH_PLL,
- .internal_osc = 1,
- .pll_freq = 500000000,
- .div_freq = {
- 5000000, 50000000, 125000000, 250000000, 25000000,
- },
- },
-};
-
-static const short sdio1_pins[] = {
- TNETV107X_PIN_SDIO1_CLK_1, TNETV107X_PIN_SDIO1_CMD_1,
- TNETV107X_PIN_SDIO1_DATA0_1, TNETV107X_PIN_SDIO1_DATA1_1,
- TNETV107X_PIN_SDIO1_DATA2_1, TNETV107X_PIN_SDIO1_DATA3_1,
- -1
-};
-
-static const short uart1_pins[] = {
- TNETV107X_PIN_UART1_RD, TNETV107X_PIN_UART1_TD, -1
-};
-
-static const short ssp_pins[] = {
- TNETV107X_PIN_SSP0_0, TNETV107X_PIN_SSP0_1, TNETV107X_PIN_SSP0_2,
- TNETV107X_PIN_SSP1_0, TNETV107X_PIN_SSP1_1, TNETV107X_PIN_SSP1_2,
- TNETV107X_PIN_SSP1_3, -1
-};
-
-int board_init(void)
-{
-#ifndef CONFIG_USE_IRQ
- __raw_writel(0, INTC_GLB_EN); /* Global disable */
- __raw_writel(0, INTC_HINT_EN); /* Disable host ints */
- __raw_writel(0, INTC_EN_CLR0 + 0); /* Clear enable */
- __raw_writel(0, INTC_EN_CLR0 + 4); /* Clear enable */
- __raw_writel(0, INTC_EN_CLR0 + 8); /* Clear enable */
-#endif
-
- gd->bd->bi_arch_number = MACH_TYPE_TNETV107X;
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- init_plls(ARRAY_SIZE(pll_config), pll_config);
-
- init_async_emif(ARRAY_SIZE(async_emif_config), async_emif_config);
-
- mux_select_pin(TNETV107X_PIN_ASR_CS3);
- mux_select_pins(sdio1_pins);
- mux_select_pins(uart1_pins);
- mux_select_pins(ssp_pins);
-
- return 0;
-}
-
-int dram_init(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return 0;
-}
-
-#ifdef CONFIG_NAND_DAVINCI
-int board_nand_init(struct nand_chip *nand)
-{
- davinci_nand_init(nand);
-
- return 0;
-}
-#endif
diff --git a/configs/tnetv107x_evm_defconfig b/configs/tnetv107x_evm_defconfig
deleted file mode 100644
index b0915d2..0000000
--- a/configs/tnetv107x_evm_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_TNETV107X_EVM=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7ce7101..f34afce 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+tnetv107x arm arm1176 - - Chan-Taek Park <c-park@ti.com>
a320evb arm arm920t - - Po-Yu Chuang <ratbert@faraday-tech.com>
cm4008 arm arm920t - - Greg Ungerer <greg.ungerer@opengear.com>
cm41xx arm arm920t - -
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 1dc0f5a..482a4bd 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -10,7 +10,6 @@ obj-$(CONFIG_FTWDT010_WATCHDOG) += ftwdt010_wdt.o
ifneq (,$(filter $(SOC), mx31 mx35 mx5 mx6 vf610 ls102xa))
obj-y += imx_watchdog.o
endif
-obj-$(CONFIG_TNETV107X_WATCHDOG) += tnetv107x_wdt.o
obj-$(CONFIG_S5P) += s5p_wdt.o
obj-$(CONFIG_XILINX_TB_WATCHDOG) += xilinx_tb_wdt.o
obj-$(CONFIG_BFIN_WATCHDOG) += bfin_wdt.o
diff --git a/drivers/watchdog/tnetv107x_wdt.c b/drivers/watchdog/tnetv107x_wdt.c
deleted file mode 100644
index 3d3f366..0000000
--- a/drivers/watchdog/tnetv107x_wdt.c
+++ /dev/null
@@ -1,165 +0,0 @@
-/*
- * TNETV107X: Watchdog timer implementation (for reset)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-
-#define MAX_DIV 0xFFFE0001
-
-struct wdt_regs {
- u32 kick_lock;
-#define KICK_LOCK_1 0x5555
-#define KICK_LOCK_2 0xaaaa
- u32 kick;
-
- u32 change_lock;
-#define CHANGE_LOCK_1 0x6666
-#define CHANGE_LOCK_2 0xbbbb
- u32 change;
-
- u32 disable_lock;
-#define DISABLE_LOCK_1 0x7777
-#define DISABLE_LOCK_2 0xcccc
-#define DISABLE_LOCK_3 0xdddd
- u32 disable;
-
- u32 prescale_lock;
-#define PRESCALE_LOCK_1 0x5a5a
-#define PRESCALE_LOCK_2 0xa5a5
- u32 prescale;
-};
-
-static struct wdt_regs* regs = (struct wdt_regs *)TNETV107X_WDT0_ARM_BASE;
-
-#define wdt_reg_read(reg) __raw_readl(®s->reg)
-#define wdt_reg_write(reg, val) __raw_writel((val), ®s->reg)
-
-static int write_prescale_reg(unsigned long prescale_value)
-{
- wdt_reg_write(prescale_lock, PRESCALE_LOCK_1);
- if ((wdt_reg_read(prescale_lock) & 0x3) != 0x1)
- return -1;
-
- wdt_reg_write(prescale_lock, PRESCALE_LOCK_2);
- if ((wdt_reg_read(prescale_lock) & 0x3) != 0x3)
- return -1;
-
- wdt_reg_write(prescale, prescale_value);
-
- return 0;
-}
-
-static int write_change_reg(unsigned long initial_timer_value)
-{
- wdt_reg_write(change_lock, CHANGE_LOCK_1);
- if ((wdt_reg_read(change_lock) & 0x3) != 0x1)
- return -1;
-
- wdt_reg_write(change_lock, CHANGE_LOCK_2);
- if ((wdt_reg_read(change_lock) & 0x3) != 0x3)
- return -1;
-
- wdt_reg_write(change, initial_timer_value);
-
- return 0;
-}
-
-static int wdt_control(unsigned long disable_value)
-{
- wdt_reg_write(disable_lock, DISABLE_LOCK_1);
- if ((wdt_reg_read(disable_lock) & 0x3) != 0x1)
- return -1;
-
- wdt_reg_write(disable_lock, DISABLE_LOCK_2);
- if ((wdt_reg_read(disable_lock) & 0x3) != 0x2)
- return -1;
-
- wdt_reg_write(disable_lock, DISABLE_LOCK_3);
- if ((wdt_reg_read(disable_lock) & 0x3) != 0x3)
- return -1;
-
- wdt_reg_write(disable, disable_value);
- return 0;
-}
-
-static int wdt_set_period(unsigned long msec)
-{
- unsigned long change_value, count_value;
- unsigned long prescale_value = 1;
- unsigned long refclk_khz, maxdiv;
- int ret;
-
- refclk_khz = clk_get_rate(TNETV107X_LPSC_WDT_ARM);
- maxdiv = (MAX_DIV / refclk_khz);
-
- if ((!msec) || (msec > maxdiv))
- return -1;
-
- count_value = refclk_khz * msec;
- if (count_value > 0xffff) {
- change_value = count_value / 0xffff + 1;
- prescale_value = count_value / change_value;
- } else {
- change_value = count_value;
- }
-
- ret = write_prescale_reg(prescale_value - 1);
- if (ret)
- return ret;
-
- ret = write_change_reg(change_value);
- if (ret)
- return ret;
-
- return 0;
-}
-
-unsigned long last_wdt = -1;
-
-int wdt_start(unsigned long msecs)
-{
- int ret;
- ret = wdt_control(0);
- if (ret)
- return ret;
- ret = wdt_set_period(msecs);
- if (ret)
- return ret;
- ret = wdt_control(1);
- if (ret)
- return ret;
- ret = wdt_kick();
- last_wdt = msecs;
- return ret;
-}
-
-int wdt_stop(void)
-{
- last_wdt = -1;
- return wdt_control(0);
-}
-
-int wdt_kick(void)
-{
- wdt_reg_write(kick_lock, KICK_LOCK_1);
- if ((wdt_reg_read(kick_lock) & 0x3) != 0x1)
- return -1;
-
- wdt_reg_write(kick_lock, KICK_LOCK_2);
- if ((wdt_reg_read(kick_lock) & 0x3) != 0x3)
- return -1;
-
- wdt_reg_write(kick, 1);
- return 0;
-}
-
-void reset_cpu(ulong addr)
-{
- clk_enable(TNETV107X_LPSC_WDT_ARM);
- wdt_start(1);
- wdt_kick();
-}
diff --git a/include/configs/tnetv107x_evm.h b/include/configs/tnetv107x_evm.h
deleted file mode 100644
index 00a1a9e..0000000
--- a/include/configs/tnetv107x_evm.h
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * Copyright (C) 2008 Texas Instruments, Inc <www.ti.com>
- *
- * Based on davinci_dvevm.h. Original Copyrights follow:
- *
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <linux/sizes.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/clock.h>
-
-/* Architecture, CPU, etc */
-#define CONFIG_TNETV107X
-#define CONFIG_TNETV107X_EVM
-#define CONFIG_TNETV107X_WATCHDOG
-#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_DISABLE_TCM
-#define CONFIG_PERIPORT_REMAP
-#define CONFIG_PERIPORT_BASE 0x2000000
-#define CONFIG_PERIPORT_SIZE 0x10
-#define CONFIG_SYS_CLK_FREQ clk_get_rate(TNETV107X_LPSC_ARM)
-
-#define CONFIG_SYS_TIMERBASE TNETV107X_TIMER0_BASE
-#define CONFIG_SYS_HZ_CLOCK clk_get_rate(TNETV107X_LPSC_TIMER0)
-
-#define CONFIG_PLL_SYS_EXT_FREQ 25000000
-#define CONFIG_PLL_TDM_EXT_FREQ 19200000
-#define CONFIG_PLL_ETH_EXT_FREQ 25000000
-
-/* Memory Info */
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024)
-#define PHYS_SDRAM_1 TNETV107X_DDR_EMIF_DATA_BASE
-#define PHYS_SDRAM_1_SIZE 0x04000000
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024)
-#define CONFIG_NR_DRAM_BANKS 1
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/* Serial Driver Info */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_COM1 TNETV107X_UART1_BASE
-#define CONFIG_SYS_NS16550_CLK clk_get_rate(TNETV107X_LPSC_UART1)
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* Flash and environment info */
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_ENV_SIZE (SZ_128K)
-#define CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_NAND_1BIT_ECC
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_SYS_NAND_BASE TNETV107X_ASYNC_EMIF_DATA_CE0_BASE
-#define CONFIG_SYS_NAND_MASK_CLE 0x10
-#define CONFIG_SYS_NAND_MASK_ALE 0x8
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_JFFS2_NAND
-#define CONFIG_ENV_OFFSET 0x180000
-
-/*
- * davinci_nand is a bit of a misnomer since this particular EMIF block is
- * commonly used across multiple TI devices. Unfortunately, this misnomer
- * (amongst others) carries forward into the kernel too. Consequently, if we
- * use a different device name here, the mtdparts variable won't be usable as
- * a kernel command-line argument.
- */
-#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=davinci_nand.0:" \
- "1536k(uboot)ro," \
- "128k(params)ro," \
- "4m(kernel)," \
- "-(filesystem)"
-
-/* General U-Boot configuration */
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_SYS_PROMPT "U-Boot > "
-#define CONFIG_SYS_CBSIZE 1024
-#define CONFIG_SYS_MAXARGS 64
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + \
- 0x700000)
-#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS "mem=32M console=ttyS1,115200n8 " \
- "root=/dev/mmcblk0p1 rw noinitrd"
-#define CONFIG_BOOTCOMMAND ""
-#define CONFIG_BOOTDELAY 1
-
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_EDITENV
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_ITEST
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_SOURCE
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_JFFS2
-
-#endif /* __CONFIG_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 9/9] ARM: davinci: remove hawkboard support
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (7 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 8/9] ARM: remove tnetv107x " Masahiro Yamada
@ 2015-02-22 15:20 ` Masahiro Yamada
2015-02-23 11:53 ` [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Fabio Estevam
9 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-22 15:20 UTC (permalink / raw)
To: u-boot
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/mach-davinci/Kconfig | 4 -
board/davinci/da8xxevm/Kconfig | 13 --
board/davinci/da8xxevm/MAINTAINERS | 8 -
board/davinci/da8xxevm/Makefile | 1 -
board/davinci/da8xxevm/README.hawkboard | 92 -----------
board/davinci/da8xxevm/hawkboard-ais-nand.cfg | 4 -
board/davinci/da8xxevm/hawkboard.c | 120 --------------
board/davinci/da8xxevm/u-boot-spl-hawk.lds | 69 --------
configs/hawkboard_defconfig | 4 -
configs/hawkboard_uart_defconfig | 5 -
doc/README.scrapyard | 1 +
include/configs/hawkboard.h | 220 --------------------------
12 files changed, 1 insertion(+), 540 deletions(-)
delete mode 100644 board/davinci/da8xxevm/README.hawkboard
delete mode 100644 board/davinci/da8xxevm/hawkboard-ais-nand.cfg
delete mode 100644 board/davinci/da8xxevm/hawkboard.c
delete mode 100644 board/davinci/da8xxevm/u-boot-spl-hawk.lds
delete mode 100644 configs/hawkboard_defconfig
delete mode 100644 configs/hawkboard_uart_defconfig
delete mode 100644 include/configs/hawkboard.h
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
index 613f04d..6827721 100644
--- a/arch/arm/mach-davinci/Kconfig
+++ b/arch/arm/mach-davinci/Kconfig
@@ -21,10 +21,6 @@ config TARGET_CAM_ENC_4XX
bool "CAM ENC 4xx board"
select SUPPORT_SPL
-config TARGET_HAWKBOARD
- bool "Hawkboard"
- select SUPPORT_SPL
-
config TARGET_DAVINCI_DM355EVM
bool "DM355 EVM board"
diff --git a/board/davinci/da8xxevm/Kconfig b/board/davinci/da8xxevm/Kconfig
index 1a841ce..1108e4b 100644
--- a/board/davinci/da8xxevm/Kconfig
+++ b/board/davinci/da8xxevm/Kconfig
@@ -23,16 +23,3 @@ config SYS_CONFIG_NAME
default "da850evm"
endif
-
-if TARGET_HAWKBOARD
-
-config SYS_BOARD
- default "da8xxevm"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "hawkboard"
-
-endif
diff --git a/board/davinci/da8xxevm/MAINTAINERS b/board/davinci/da8xxevm/MAINTAINERS
index dd66f07..10c4e2f 100644
--- a/board/davinci/da8xxevm/MAINTAINERS
+++ b/board/davinci/da8xxevm/MAINTAINERS
@@ -12,11 +12,3 @@ F: include/configs/da850evm.h
F: configs/da850_am18xxevm_defconfig
F: configs/da850evm_defconfig
F: configs/da850evm_direct_nor_defconfig
-
-HAWKBOARD BOARD
-M: Syed Mohammed Khasim <sm.khasim@gmail.com>
-M: Sughosh Ganu <urwithsughosh@gmail.com>
-S: Maintained
-F: include/configs/hawkboard.h
-F: configs/hawkboard_defconfig
-F: configs/hawkboard_uart_defconfig
diff --git a/board/davinci/da8xxevm/Makefile b/board/davinci/da8xxevm/Makefile
index d3acacc..4da509b 100644
--- a/board/davinci/da8xxevm/Makefile
+++ b/board/davinci/da8xxevm/Makefile
@@ -9,4 +9,3 @@
obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += da830evm.o
obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += da850evm.o
-obj-$(CONFIG_MACH_DAVINCI_HAWK) += hawkboard.o
diff --git a/board/davinci/da8xxevm/README.hawkboard b/board/davinci/da8xxevm/README.hawkboard
deleted file mode 100644
index d6ae02e..0000000
--- a/board/davinci/da8xxevm/README.hawkboard
+++ /dev/null
@@ -1,92 +0,0 @@
-Summary
-=======
-The README is for the boot procedure used for TI's OMAP-L138 based
-hawkboard. The hawkboard comes with a 128MiB Nand flash and a 128MiB
-DDR SDRAM along with a host of other controllers.
-
-The hawkboard is booted in three stages. The initial bootloader which
-executes upon reset is the Rom Boot Loader(RBL) which sits in the
-internal ROM of the omap. The RBL initialises the memory and the nand
-controller, and copies the image stored at a predefined location(block
-1) of the nand flash. The image loaded by the RBL to the memory is the
-AIS signed spl image. This, in turns copies the u-boot binary from the
-nand flash to the memory and jumps to the u-boot entry point.
-
-AIS is an image format defined by TI for the images that are to be
-loaded to memory by the RBL. The image is divided into a series of
-sections and the image's entry point is specified. Each section comes
-with meta data like the target address the section is to be copied to
-and the size of the section, which is used by the RBL to load the
-image. At the end of the image the RBL jumps to the image entry
-point.
-
-The secondary stage bootloader(spl) which is loaded by the RBL then
-loads the u-boot from a predefined location in the nand to the memory
-and jumps to the u-boot entry point.
-
-The reason a secondary stage bootloader is used is because the ECC
-layout expected by the RBL is not the same as that used by
-u-boot/linux. This also implies that for flashing the spl image,we
-need to use the u-boot which uses the ECC layout expected by the
-RBL[1]. Booting u-boot over UART(UART boot) is explained here[2].
-
-
-Compilation
-===========
-Three images might be needed
-
-* spl - This is the secondary bootloader which boots the u-boot
- binary.
-
-* u-boot binary - This is the image flashed to the nand and copied to
- the memory by the spl.
-
- Both the images get compiled with hawkboard_config, with the TOPDIR
- containing the u-boot images, and the spl image under the spl
- directory.
-
- The spl image needs to be processed with the AISGen tool for
- generating the AIS signed image to be flashed. Steps for generating
- the AIS image are explained here[3].
-
-* u-boot for uart boot - This is same as the u-boot binary generated
- above, with the sole difference of the CONFIG_SYS_TEXT_BASE being
- 0xc1080000, as expected by the RBL.
-
- hawkboard_uart_config
-
-
-Flashing the images to Nand
-===========================
-The spl AIS image needs to be flashed to the block 1 of the Nand
-flash, as that is the location the RBL expects the image[4]. For
-flashing the spl, boot over the u-boot specified in [1], and flash the
-image
-
-=> tftpboot 0xc0700000 <nand_spl_ais.bin>
-=> nand erase 0x20000 0x20000
-=> nand write.e 0xc0700000 0x20000 <nand_spl_size>
-
-The u-boot binary is flashed at location 0xe0000(block 6) of the nand
-flash. The spl loader expects the u-boot at this location. For
-flashing the u-boot binary
-
-=> tftpboot 0xc0700000 u-boot.bin
-=> nand erase 0xe0000 0x40000
-=> nand write.e 0xc0700000 0xe0000 <u-boot-size>
-
-
-Links
-=====
-
-[1]
- http://code.google.com/p/hawkboard/downloads/detail?name=u-boot_uart_ais_v1.bin
-
-[2]
- http://elinux.org/Hawkboard#Booting_u-boot_over_UART
-
-[3]
- http://elinux.org/Hawkboard#Signing_u-boot_for_UART_boot
-
-[4]
- http://processors.wiki.ti.com/index.php/RBL_UBL_and_host_program#RBL_booting_from_NAND_and_ECC.2FBad_blocks
diff --git a/board/davinci/da8xxevm/hawkboard-ais-nand.cfg b/board/davinci/da8xxevm/hawkboard-ais-nand.cfg
deleted file mode 100644
index 2b12b6c..0000000
--- a/board/davinci/da8xxevm/hawkboard-ais-nand.cfg
+++ /dev/null
@@ -1,4 +0,0 @@
-# PLL0CFG0 PLL0CFG1
-PLL0 0x00180001 0x00000205
-# PLL1CFG0 PLL1CFG1 DRPYC1R SDCR SDTIMR1 SDTIMR2 SDRCR CLK2XSRC
-DDR2 0x15010001 0x00000002 0x00000043 0x00134632 0x26492a09 0x7d13c722 0x00000249 0x00000000
diff --git a/board/davinci/da8xxevm/hawkboard.c b/board/davinci/da8xxevm/hawkboard.c
deleted file mode 100644
index d5992a5..0000000
--- a/board/davinci/da8xxevm/hawkboard.c
+++ /dev/null
@@ -1,120 +0,0 @@
-/*
- * Modified for Hawkboard - Syed Mohammed Khasim <khasim@beagleboard.org>
- *
- * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar@ti.com>
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- * Copyright (C) 2004 Texas Instruments.
- * Copyright (C) 2012 Sughosh Ganu <urwithsughosh@gmail.com>.
- *
- * ----------------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <asm/errno.h>
-#include <asm/arch/hardware.h>
-#include <asm/io.h>
-#include <asm/arch/davinci_misc.h>
-#include <asm/arch/pinmux_defs.h>
-#include <asm/arch/da8xx-usb.h>
-#include <ns16550.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct pinmux_resource pinmuxes[] = {
- PINMUX_ITEM(emac_pins_mii),
- PINMUX_ITEM(emac_pins_mdio),
- PINMUX_ITEM(emifa_pins_cs3),
- PINMUX_ITEM(emifa_pins_cs4),
- PINMUX_ITEM(emifa_pins_nand),
- PINMUX_ITEM(uart2_pins_txrx),
- PINMUX_ITEM(uart2_pins_rtscts),
-};
-
-const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
-
-const struct lpsc_resource lpsc[] = {
- { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
- { DAVINCI_LPSC_SPI1 }, /* Serial Flash */
- { DAVINCI_LPSC_EMAC }, /* image download */
- { DAVINCI_LPSC_UART2 }, /* console */
- { DAVINCI_LPSC_GPIO },
-};
-
-const int lpsc_size = ARRAY_SIZE(lpsc);
-
-int board_init(void)
-{
- /* arch number of the board */
- gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_HAWKBOARD;
-
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- return 0;
-}
-
-int board_early_init_f(void)
-{
- /*
- * Kick Registers need to be set to allow access to Pin Mux registers
- */
- writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0);
- writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1);
-
- /* set cfgchip3 to select mii */
- writel(readl(&davinci_syscfg_regs->cfgchip3) &
- ~(1 << 8), &davinci_syscfg_regs->cfgchip3);
-
- return 0;
-}
-
-int misc_init_r(void)
-{
- char buf[32];
-
- printf("ARM Clock : %s MHz\n",
- strmhz(buf, clk_get(DAVINCI_ARM_CLKID)));
-
- return 0;
-}
-
-int usb_phy_on(void)
-{
- u32 timeout;
- u32 cfgchip2;
-
- cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
-
- cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN |
- CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ |
- CFGCHIP2_USB1PHYCLKMUX);
- cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON |
- CFGCHIP2_REFFREQ_24MHZ | CFGCHIP2_USB2PHYCLKMUX |
- CFGCHIP2_USB1SUSPENDM;
-
- writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
-
- /* wait until the usb phy pll locks */
- timeout = DA8XX_USB_OTG_TIMEOUT;
- while (timeout--)
- if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD)
- return 1;
-
- /* USB phy was not turned on */
- return 0;
-}
-
-void usb_phy_off(void)
-{
- u32 cfgchip2;
-
- /*
- * Power down the on-chip PHY.
- */
- cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
- cfgchip2 &= ~(CFGCHIP2_PHY_PLLON | CFGCHIP2_USB1SUSPENDM);
- cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | CFGCHIP2_RESET;
- writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
-}
diff --git a/board/davinci/da8xxevm/u-boot-spl-hawk.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds
deleted file mode 100644
index 5c629db..0000000
--- a/board/davinci/da8xxevm/u-boot-spl-hawk.lds
+++ /dev/null
@@ -1,69 +0,0 @@
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0xc1080000;
-
- . = ALIGN(4);
- .text :
- {
- *(.vectors)
- arch/arm/cpu/arm926ejs/start.o (.text*)
- arch/arm/cpu/arm926ejs/built-in.o (.text*)
- drivers/mtd/nand/built-in.o (.text*)
-
- *(.text*)
- }
-
- . = ALIGN(4);
- .rodata : { *(.rodata*) }
-
- . = ALIGN(4);
- .data : {
- *(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
- }
-
- . = ALIGN(4);
- __image_copy_end = .;
- __rel_dyn_start = .;
- __rel_dyn_end = .;
-
- __got_start = .;
- . = ALIGN(4);
- .got : { *(.got) }
-
- __got_end = .;
-
- .bss :
- {
- . = ALIGN(4);
- __bss_start = .;
- *(.bss*)
- . = ALIGN(4);
- __bss_end = .;
- }
-
- .end :
- {
- *(.__end)
- }
-}
diff --git a/configs/hawkboard_defconfig b/configs/hawkboard_defconfig
deleted file mode 100644
index 4084f9c..0000000
--- a/configs/hawkboard_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SPL=y
-+S:CONFIG_ARM=y
-+S:CONFIG_ARCH_DAVINCI=y
-+S:CONFIG_TARGET_HAWKBOARD=y
diff --git a/configs/hawkboard_uart_defconfig b/configs/hawkboard_uart_defconfig
deleted file mode 100644
index d7eeae7..0000000
--- a/configs/hawkboard_uart_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="UART_U_BOOT"
-+S:CONFIG_ARM=y
-+S:CONFIG_ARCH_DAVINCI=y
-+S:CONFIG_TARGET_HAWKBOARD=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index f34afce..9f84d4a 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+hawkboard arm arm926ejs - - Syed Mohammed Khasim <sm.khasim@gmail.com>:Sughosh Ganu <urwithsughosh@gmail.com>
tnetv107x arm arm1176 - - Chan-Taek Park <c-park@ti.com>
a320evb arm arm920t - - Po-Yu Chuang <ratbert@faraday-tech.com>
cm4008 arm arm920t - - Greg Ungerer <greg.ungerer@opengear.com>
diff --git a/include/configs/hawkboard.h b/include/configs/hawkboard.h
deleted file mode 100644
index 1d78e72..0000000
--- a/include/configs/hawkboard.h
+++ /dev/null
@@ -1,220 +0,0 @@
-/*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on davinci_dvevm.h. Original Copyrights follow:
- *
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Board
- */
-#define CONFIG_SYS_USE_NAND 1
-
-/*
- * SoC Configuration
- */
-#define CONFIG_MACH_DAVINCI_HAWK
-#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */
-#define CONFIG_SOC_DA850 /* TI DA850 SoC */
-#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
-#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
-#define CONFIG_SYS_OSCIN_FREQ 24000000
-#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
-#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_AIS_CONFIG_FILE "board/$(BOARDDIR)/hawkboard-ais-nand.cfg"
-
-#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
- DAVINCI_SYSCFG_SUSPSRC_EMAC | \
- DAVINCI_SYSCFG_SUSPSRC_I2C | \
- DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
- DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
- DAVINCI_SYSCFG_SUSPSRC_UART2)
-
-#if defined(CONFIG_UART_U_BOOT)
-#define CONFIG_SYS_TEXT_BASE 0xc1080000
-#elif !defined(CONFIG_SPL_BUILD)
-#define CONFIG_SYS_TEXT_BASE 0xc1180000
-#endif
-
-/* Spl */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_LIBGENERIC_SUPPORT /* for udelay and __div64_32 for NAND */
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-hawk.lds"
-#define CONFIG_SPL_TEXT_BASE 0xc1080000
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
-
-/*
- * Memory Info
- */
-#define CONFIG_SYS_MALLOC_LEN (1*1024*1024) /* malloc() len */
-#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */
-#define CONFIG_SYS_SDRAM_BASE 0xc0000000
-#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 -\
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_MONITOR_LEN 0x60000
-
-/* memtest start addr */
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1)
-
-/* memtest will be run on 16MB */
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024)
-
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-
-/*
- * Serial Driver info
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE
-#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Network & Ethernet Configuration
- */
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-
-/*
- * Nand Flash
- */
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE (128 << 10)
-#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
-#define CONFIG_CLE_MASK 0x10
-#define CONFIG_ALE_MASK 0x8
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
-#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST /* SPL nand driver configuration */
-#define CFG_DAVINCI_STD_NAND_LAYOUT
-#define CONFIG_SYS_NAND_CS 3
-#define CONFIG_SYS_NAND_PAGE_2K
-/* Max number of NAND devices */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE_LIST { 0x62000000, }
-/* Block 0--not used by bootcode */
-#define CONFIG_ENV_OFFSET 0x0
-
-#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0xe0000
-#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1180000
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
- CONFIG_SYS_NAND_U_BOOT_SIZE - \
- CONFIG_SYS_MALLOC_LEN - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_NAND_ECCPOS { \
- 24, 25, 26, 27, 28, \
- 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
- 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
- 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
- 59, 60, 61, 62, 63 }
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 10
-#define CONFIG_SYS_NAND_OOBSIZE 64
-
-#endif /* CONFIG_SYS_USE_NAND */
-
-/* USB Configs */
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_OHCI_DA8XX
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x01E25000
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "hawkboard"
-
-/*
- * U-Boot general configuration
- */
-#define CONFIG_MISC_INIT_R
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_PROMPT "hawkboard > " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-
-/*
- * Linux Information
- */
-#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS \
- "mem=128M console=ttyS2,115200n8 root=/dev/ram0 rw initrd=0xc1180000,"\
- "4M ip=static"
-#define CONFIG_BOOTDELAY 3
-
-/*
- * U-Boot commands
- */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_EXT2
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#ifdef CONFIG_SYS_USE_NAND
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-#define CONFIG_CMD_NAND
-#endif
-
-#ifndef CONFIG_DRIVER_TI_EMAC
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_DHCP
-#undef CONFIG_CMD_MII
-#undef CONFIG_CMD_PING
-#endif
-
-#endif /* __CONFIG_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
` (8 preceding siblings ...)
2015-02-22 15:20 ` [U-Boot] [PATCH v4 9/9] ARM: davinci: remove hawkboard support Masahiro Yamada
@ 2015-02-23 11:53 ` Fabio Estevam
9 siblings, 0 replies; 19+ messages in thread
From: Fabio Estevam @ 2015-02-23 11:53 UTC (permalink / raw)
To: u-boot
Hi Masahiro,
On Sun, Feb 22, 2015 at 12:20 PM, Masahiro Yamada
<yamada.m@jp.panasonic.com> wrote:
>
> Based on Tom's announce mail
> (http://lists.denx.de/pipermail/u-boot/2015-February/203606.html),
> let's start removing non-generic ARM boards.
>
> No conversion patches have been posted for these boards.
>
>
> Changes in v4:
> - Rebase on commit 4641429695
>
> Changes in v3:
> - Do not remove devkit3250 because Vladimir has post a patch
> to convert it into Generic Board.
>
> Changes in v2:
> - Do not remove armada100 boards because Ajay will send a patch
> to convert them.
>
> Masahiro Yamada (9):
> ARM: remove mx31ads board support
> ARM: mx31: remove imx31_phycore board
> ARM: remove jadecpu board support
> ARM: remove zmx25 board support
I have just sent patches converting mx31ads, mx31_phycore and zmx25 to
generic board.
Regards,
Fabio Estevam
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 2/9] ARM: mx31: remove imx31_phycore board
2015-02-22 15:20 ` [U-Boot] [PATCH v4 2/9] ARM: mx31: remove imx31_phycore board Masahiro Yamada
@ 2015-02-23 13:09 ` Anatolij Gustschin
0 siblings, 0 replies; 19+ messages in thread
From: Anatolij Gustschin @ 2015-02-23 13:09 UTC (permalink / raw)
To: u-boot
Hi Masahiro,
On Mon, 23 Feb 2015 00:20:10 +0900
Masahiro Yamada <yamada.m@jp.panasonic.com> wrote:
...
> 10 files changed, 1 insertion(+), 485 deletions(-)
> delete mode 100644 board/imx31_phycore/Kconfig
> delete mode 100644 board/imx31_phycore/MAINTAINERS
> delete mode 100644 board/imx31_phycore/Makefile
> delete mode 100644 board/imx31_phycore/imx31_phycore.c
> delete mode 100644 board/imx31_phycore/lowlevel_init.S
> delete mode 100644 configs/imx31_phycore_defconfig
> delete mode 100644 configs/imx31_phycore_eet_defconfig
> delete mode 100644 include/configs/imx31_phycore.h
There is a pending patch, converting this board to generic board.
I'll test it in the next week, so do not remove this board, please.
Thanks,
Anatolij
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 4/9] ARM: remove zmx25 board support
2015-02-22 15:20 ` [U-Boot] [PATCH v4 4/9] ARM: remove zmx25 " Masahiro Yamada
@ 2015-02-23 22:30 ` Fabio Estevam
0 siblings, 0 replies; 19+ messages in thread
From: Fabio Estevam @ 2015-02-23 22:30 UTC (permalink / raw)
To: u-boot
On Sun, Feb 22, 2015 at 12:20 PM, Masahiro Yamada
<yamada.m@jp.panasonic.com> wrote:
> This is still a non-generic board.
>
> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
> Cc: Matthias Weisser <weisserm@arcor.de>
> Acked-by: Marek Vasut <marex@denx.de>
I have sent a patch adding generic support for this board. Please do
not remove it.
Thanks
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-02-22 15:20 ` [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support Masahiro Yamada
@ 2015-02-23 22:32 ` Fabio Estevam
2015-02-24 2:54 ` Masahiro Yamada
0 siblings, 1 reply; 19+ messages in thread
From: Fabio Estevam @ 2015-02-23 22:32 UTC (permalink / raw)
To: u-boot
On Sun, Feb 22, 2015 at 12:20 PM, Masahiro Yamada
<yamada.m@jp.panasonic.com> wrote:
> This is still a non-generic board.
>
> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
> Acked-by: Marek Vasut <marex@denx.de>
I have sent a patch adding generic support for this board. Please do
not remove it.
Thanks
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-02-23 22:32 ` Fabio Estevam
@ 2015-02-24 2:54 ` Masahiro Yamada
2015-02-24 12:46 ` Fabio Estevam
0 siblings, 1 reply; 19+ messages in thread
From: Masahiro Yamada @ 2015-02-24 2:54 UTC (permalink / raw)
To: u-boot
Hi Fabio,
Thanks for converting some boards.
I have dropped 1/9, 2/9, 4/9
and have posted v5.
BTW, is it possible to use the common linker script
instead of board/freescale/mx31ads/u-boot.lds ?
I am just wondering why U-Boot nees so many
board-customised linker scripts.
On Mon, 23 Feb 2015 19:32:23 -0300
Fabio Estevam <festevam@gmail.com> wrote:
> On Sun, Feb 22, 2015 at 12:20 PM, Masahiro Yamada
> <yamada.m@jp.panasonic.com> wrote:
> > This is still a non-generic board.
> >
> > Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
> > Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
> > Acked-by: Marek Vasut <marex@denx.de>
>
> I have sent a patch adding generic support for this board. Please do
> not remove it.
>
> Thanks
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-02-24 2:54 ` Masahiro Yamada
@ 2015-02-24 12:46 ` Fabio Estevam
2015-03-17 6:07 ` Masahiro Yamada
0 siblings, 1 reply; 19+ messages in thread
From: Fabio Estevam @ 2015-02-24 12:46 UTC (permalink / raw)
To: u-boot
On Mon, Feb 23, 2015 at 11:54 PM, Masahiro Yamada
<yamada.m@jp.panasonic.com> wrote:
> Hi Fabio,
>
> Thanks for converting some boards.
>
> I have dropped 1/9, 2/9, 4/9
> and have posted v5.
Thanks, Masahiro.
>
> BTW, is it possible to use the common linker script
> instead of board/freescale/mx31ads/u-boot.lds ?
Yes, I think this is a good idea.
Regards,
Fabio Estevam
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-02-24 12:46 ` Fabio Estevam
@ 2015-03-17 6:07 ` Masahiro Yamada
2015-04-08 15:21 ` Fabio Estevam
0 siblings, 1 reply; 19+ messages in thread
From: Masahiro Yamada @ 2015-03-17 6:07 UTC (permalink / raw)
To: u-boot
Hi Fabio,
2015-02-24 21:46 GMT+09:00 Fabio Estevam <festevam@gmail.com>:
> On Mon, Feb 23, 2015 at 11:54 PM, Masahiro Yamada
> <yamada.m@jp.panasonic.com> wrote:
>> Hi Fabio,
>>
>> Thanks for converting some boards.
>>
>> I have dropped 1/9, 2/9, 4/9
>> and have posted v5.
>
> Thanks, Masahiro.
>
>>
>> BTW, is it possible to use the common linker script
>> instead of board/freescale/mx31ads/u-boot.lds ?
>
> Yes, I think this is a good idea.
>
Could you do it, please?
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-03-17 6:07 ` Masahiro Yamada
@ 2015-04-08 15:21 ` Fabio Estevam
2015-04-09 11:37 ` Masahiro Yamada
0 siblings, 1 reply; 19+ messages in thread
From: Fabio Estevam @ 2015-04-08 15:21 UTC (permalink / raw)
To: u-boot
Hi Masahiro
On Tue, Mar 17, 2015 at 3:07 AM, Masahiro Yamada
<yamada.masahiro@socionext.com> wrote:
>>> BTW, is it possible to use the common linker script
>>> instead of board/freescale/mx31ads/u-boot.lds ?
>>
>> Yes, I think this is a good idea.
>
> Could you do it, please?
I don't have access to a mx31ads board, so I can't work on it.
Regards,
Fabio Estevam
^ permalink raw reply [flat|nested] 19+ messages in thread
* [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support
2015-04-08 15:21 ` Fabio Estevam
@ 2015-04-09 11:37 ` Masahiro Yamada
0 siblings, 0 replies; 19+ messages in thread
From: Masahiro Yamada @ 2015-04-09 11:37 UTC (permalink / raw)
To: u-boot
Hi Fabio,
2015-04-09 0:21 GMT+09:00 Fabio Estevam <festevam@gmail.com>:
> Hi Masahiro
>
> On Tue, Mar 17, 2015 at 3:07 AM, Masahiro Yamada
> <yamada.masahiro@socionext.com> wrote:
>
>>>> BTW, is it possible to use the common linker script
>>>> instead of board/freescale/mx31ads/u-boot.lds ?
>>>
>>> Yes, I think this is a good idea.
>>
>> Could you do it, please?
>
> I don't have access to a mx31ads board, so I can't work on it.
>
OK.
IIRC, we are supposed to do run-test just in case
when we convert a board into Generic board.
So, I thought you had this board.
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2015-04-09 11:37 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-02-22 15:20 [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 1/9] ARM: remove mx31ads board support Masahiro Yamada
2015-02-23 22:32 ` Fabio Estevam
2015-02-24 2:54 ` Masahiro Yamada
2015-02-24 12:46 ` Fabio Estevam
2015-03-17 6:07 ` Masahiro Yamada
2015-04-08 15:21 ` Fabio Estevam
2015-04-09 11:37 ` Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 2/9] ARM: mx31: remove imx31_phycore board Masahiro Yamada
2015-02-23 13:09 ` Anatolij Gustschin
2015-02-22 15:20 ` [U-Boot] [PATCH v4 3/9] ARM: remove jadecpu board support Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 4/9] ARM: remove zmx25 " Masahiro Yamada
2015-02-23 22:30 ` Fabio Estevam
2015-02-22 15:20 ` [U-Boot] [PATCH v4 5/9] ARM: remove dkb " Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 6/9] ARM: remove cm4008 and cm41xx " Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 7/9] ARM: remove a320evb " Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 8/9] ARM: remove tnetv107x " Masahiro Yamada
2015-02-22 15:20 ` [U-Boot] [PATCH v4 9/9] ARM: davinci: remove hawkboard support Masahiro Yamada
2015-02-23 11:53 ` [U-Boot] [PATCH v4 0/9] ARM: remove non-generic boards Fabio Estevam
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.